Software - Backup - D-Link

Table of Contents
Table of Contents
Introduction ................................................................................... 1
Product Overview .............................................................. 2
Package Contents ......................................................................... 2
System Requirements ................................................................. 2
Features............................................................................................ 3
Hardware Overview ..................................................................... 5
Front Panel .............................................................................. 5
Hardware Overview ..................................................................... 6
Front Panel .............................................................................. 6
Rear Panel (Connections) ................................................... 7
Using the OLED ............................................................................. 8
Chapter 1 - Hardware ........................................................ 9
Hardware Setup - Installing Hard Drives ............................10
Hardware Setup - Removing Brackets ................................11
Hardware Setup - Attaching the Hard Drive to the Hard
Drive Tray .......................................................................................12
Hardware Setup - Installing Hard Drives ............................13
Network Setup - Plugging in the Network Cables..........14
Network Setup - Plugging in the Cables ............................15
Power Cable Setup - Plugging in the Cables ....................16
Powering on the Device ...........................................................17
Powering on the Device - Software .....................................18
Chapter 2 - Software Installation ...................................19
Software Setup - Default IP Address Location .................20
Software Setup - EZ Search Utility........................................21
D-Link ShareCenter Pro 1100-04 User Manual
Getting Started ............................................................................22
Getting Started - Browser Setup ...........................................24
Using the Web UI ........................................................................26
Using the Web UI Part II ............................................................27
Understanding the Web UI .....................................................28
Understanding the WEB UI Part II .........................................29
Chapter 3 - Setup Wizard .........................................................30
Using the Setup Wizard for the First Time .........................31
Using the Setup Wizard for the First Time .........................32
Using the Setup Wizard for the First Time .........................33
Using the Setup Wizard for the First Time .........................34
Using the Setup Wizard for Static IP Addresses ...............35
Using the Setup Wizard for Static IP Addresses ...............36
Using the Setup Wizard for Host Names ............................37
Using the Setup Wizard for File Sharing .............................38
Using the Setup Wizard for RAID Levels .............................39
Encrypting your Drive ...............................................................40
Setup Wizard Summary ............................................................41
Setup Wizard Summary Part II ...............................................42
Creating a Clean Volume..........................................................43
Formatting a Volume.................................................................44
Accessing the Drive for the First Time .................................45
Chapter 4 - Hardware - Installing more Drives ..............46
Hardware - Installing more Drives ........................................47
Hardware - Installing more Drives ........................................48
Hardware - Installing more Drives ........................................49
i
Table of Contents
Chapter 5 - Software - Creating Volumes & Formatting50
Software - Installing more Drives .........................................51
Software - Coniguring more than one drive ...................52
Software - Coniguring more than one drive ...................53
Software - Creating RAID .........................................................54
Software - Encryption Settings ..............................................55
Software - Creating the Volume ............................................56
Software - Creating the RAID & Formatting ......................57
Software - Volume & RAID Created ......................................58
Chapter 6 - Software - Creating Users ............................59
Software - Creating Users ........................................................60
Software - Creating Users ........................................................61
Software - User Information ...................................................62
Software - Creating Groups ....................................................63
Software - Creating Share Folder Lists ................................64
Software - User Summary ........................................................65
Software - User Information ...................................................66
Software - Creating more than One User...........................67
Software - Creating more than One User...........................68
Software - Creating more than One User...........................69
Software - Creating more than One User...........................70
Software - User Summary ........................................................71
Software - User Information ...................................................72
Software - Deleting a User ......................................................73
Software - Deleting a User ......................................................74
Software - Importing Users .....................................................75
Software - Importing Users .....................................................76
Software - Importing Users - Creating a User List ...........77
D-Link ShareCenter Pro 1100-04 User Manual
Software - Importing Users - Checking the User List.....78
Software - Creating a Batch User List ..................................79
Software - Creating a Batch User List ..................................80
Software - Creating a Batch User List ..................................81
Software - Creating a Batch User List ..................................82
Software - Creating a Batch User List ..................................83
Software - Creating a Batch User List ..................................84
Chapter 7 - Software - Creating a Shared Folder...........85
Software - Creating a Shared Folder ....................................86
Create Share Folder ............................................................87
Create Share Folder - Volumes & Quotas....................88
Create Share Folder - Volumes & Quotas....................89
Create Share Folder - Volumes & Quotas....................90
Create Share Folder - Volumes & Quotas....................91
Create Share Folder - Volumes & Quotas....................92
Create Share Folder - Volumes & Quotas....................93
Create Share Folder - Select Service ............................94
Create Share Folder - Access Rights .............................95
Create Share Folder - Access Rights .............................96
Shared Folders .....................................................................97
Create Share Folder - Summary .....................................98
Chapter 8 - Software - Creating a Group ........................99
Software - Creating a Group ........................................ 100
Software - Creating a Group ........................................ 101
Software - Creating a Group ........................................ 102
Software - Adding Users to a Group ......................... 103
Software - Adding Users to a Group ......................... 104
My Favorites............................................................................... 105
ii
Table of Contents
Chapter 9 - Software - Admin Password ......................106
Software - Admin Password ................................................. 107
Software - Admin Password ................................................. 108
Software - Admin Password ................................................. 109
Chapter 10 - Software - System & Hard Drive Status ..110
Software - Status Management.......................................... 111
Software - System Status ...................................................... 112
Software - System Status ...................................................... 113
System Status ............................................................................ 114
Software - Hard Drive Status ............................................... 115
Software - Hard Drive Status ............................................... 116
Software - Hard Drive Status ............................................... 117
Software - Hard Drive Status ............................................... 118
Software - Resource Monitor............................................... 119
Software - Resource Monitor............................................... 120
Software - Resource Monitor............................................... 121
Software - Resource Monitor............................................... 122
Chapter 11 - Software - Disk Management..................124
Software - Disk Management.............................................. 125
Software - Disk Management.............................................. 126
Software - Disk Management - Volume ........................... 127
Software - Disk Management - Creat a Volume ............ 128
Software - Disk Management - Create a Volume ......... 129
Software - Disk Management - Create a Volume ......... 130
Software - Disk Management - Extend/Spare a Volume131
Software - Disk Management - Migrate a Volume ....... 132
Software - Disk Management - Expand a Volume ....... 133
D-Link ShareCenter Pro 1100-04 User Manual
Disk Management - Change the Encryption Settings 134
Disk Management - Change the Encryption Settings 135
Disk Management - Change the Encryption Settings 136
iSCSI Target......................................................................... 137
iSCSI Target - iSCSI Manager ........................................ 139
iSCSI Target - iSCSI Targets ............................................ 142
iSCSI Target - Editing iSCSI Targets ............................ 148
iSCSI Target - Deleting iSCSI Targets ......................... 151
iSCSI Target - Details of an iSCSI Targets .................. 153
iSCSI Target - iSCSI LUN .................................................. 154
Edit an iSCSI LUN .............................................................. 158
View details of an iSCSI LUN ........................................ 159
iSCSI Target - LUN ACL.................................................... 160
Editing the LUN ACL ....................................................... 163
Virtual Volume .................................................................. 166
Disk Diagnostic ................................................................. 168
Disk Management - Scheduling a Disk Diagnostics ... 172
Disk Management - Scan a Volume .................................. 173
Disk Management - Format a Volume.............................. 174
Account Management ........................................................... 175
Admin Password .............................................................. 176
Users ..................................................................................... 177
Groups ................................................................................. 191
Shared Folders .................................................................. 194
Shared Folders - Editing a Shared Folder ................ 206
Shared Folders - Management.................................... 212
Accounts Management - Shared Folders ................ 229
ISO Mounts......................................................................... 230
iii
Table of Contents
ISO Mounts - Editing an ISO Mount .......................... 238
ISO Mounts - Deleting an ISO Mount ....................... 242
System Management - Edit a Syslog Server Rule . 285
System Management - Delete a Syslog Server
Rule ....................................................................................... 290
System Management - Enable/Disable a Syslog
Server Rule ......................................................................... 292
System Management - Clearing a Syslog Server
Log ........................................................................................ 293
Chapter 12 - Software - System Management .............245
Software - System Management - Network Settings . 246
Software - System Management - Network Settings . 247
System Management - Network Settings - LAN 1 ....... 248
System Management - Network Settings - LAN 2 ....... 249
System Management - Network Settings - Global Settings Chapter 13 - Software - Network Services ...................295
250
Software - Network Services........................................ 296
System Management - Network Settings - Route ....... 251
Software - Network Services - File Sharing............. 297
System Management - Network Settings - Route ....... 252
Software - Network Services - File Sharing - FTP .. 298
System Management - Time and Date Settings ........... 253
Software - Network Services - File Sharing - CIFS 299
System Management - Time and Date Settings ........... 254
Software - Network Services - File Sharing - DFS . 300
System Management - System Settings.......................... 255
Software - Network Services - File Sharing - DFS . 301
System Management - System Settings.......................... 256
Software - Network Services - Dynamic DNS ........ 302
System Management - Power Management ................. 257
Software - Network Services - Dynamic DNS ........ 303
System Management - Power Management ................. 258
Software - Network Services - SNMP ........................ 304
System Management - Schedule Settings ..................... 259
Software - Network Services - SNMP ........................ 305
System Management - Power Management - UPS ..... 260
Software - Network Services - Network Discovery
System Management - Email Alerts .................................. 268
Services ............................................................................... 306
System Management - Email Alerts .................................. 269
Software - Network Services - Network Discovery
System Management - Firmware Upgrade .................... 270
Services ............................................................................... 307
System Management - Firmware Upgrade .................... 271
System Management - Logs ................................................ 272 Chapter 14 - Software - Applications ...........................308
Software - Applications - Web File Manager .......... 309
System Management - Logs ................................................ 273
Software - Applications - Web File Manager .......... 310
System Management - Logs ................................................ 274
Software - Applications - Download Manager ...... 311
System Management - Syslog Server ............................... 275
Software - Applications - Download Manager ...... 312
System Management - Syslog Server Rule ..................... 277
D-Link ShareCenter Pro 1100-04 User Manual
iv
Table of Contents
Software - Applications - Download Manager ...... 313
Software - Applications - Download Manager ...... 314
Chapter 15 - Software - Backup ....................................315
Software - Backup............................................................ 316
Software - Backup - Volume Snapshot ..................... 317
Software - Backup - Volume Snapshot ..................... 318
Software - Backup - Volume Snapshot ..................... 319
Software - Backup - Volume Snapshot ..................... 320
Software - Backup - Volume Snapshot ..................... 321
Software - Backup - Local Backup .............................. 322
Software - Backup - Local Backup .............................. 323
Software - Backup - Local Backup .............................. 324
Software - Backup - Local Backup .............................. 325
Software - Backup - Local Backup .............................. 326
Software - Backup - Remote Backup Server........... 327
Software - Backup - Remote Backup Job ................ 328
Software - Backup - Remote Backup Job ................ 329
Software - Backup - Remote Backup Job ................ 330
Software - Backup - Remote Backup Job ................ 331
Software - Backup - Remote Backup Job ................ 332
Software - Backup - Remote Backup Job ................ 333
Software - Backup - External Backup ........................ 334
Software - Backup - External Backup ........................ 335
Software - Backup - External Backup ........................ 336
Amazon S3 ......................................................................... 337
Amazon S3 ......................................................................... 338
Chapter 19 - Appendix ..................................................347
Knowledge Base ............................................................348
What is RAID? ............................................................................ 348
Mapping a Drive ...................................................................... 350
USB Print Server ....................................................................... 353
iSCSI Drive Mapping ............................................................... 361
Hot-swap ........................................................................370
Storing non-English Character Files ............................371
Chapter 18 - Software - Extension Pack .......................344
Extension Pack .......................................................................... 345
Extension Pack .................................................................. 346
D-Link ShareCenter Pro 1100-04 User Manual
v
Section 1 - Product Overview
Introduction
The D-Link ShareCenter Pro 1100 (DNS-1100-04) 4-Bay Network Attached Storage handles the ever-growing data storage
requirements for households/SOHO and SMB users. The need for data consolidation and data sharing makes the DNS-1100-04
an ideal storage solution. Its iSCSI capability delivers blistering transfer rates and provides an extra layer of stability.
The DNS-1100-04 CD contains the D-Link’s EZ Search Utility. This utility allows you to locate the ShareCenter Pro 1100
automatically and map drives to your computer on the ly. The D-Link EZ Storage Utility allows you to conigure the device
and set IP addresses.
Once setup and conigured on your network, the DNS-1100-04, acts as a FTP, Web, Music, and Multimedia server. Windows™,
MAC, and Linux computers on the network can access any data of the server without adding new software locally and becaue
of its stable and powerful feature set sensitive data can be securely managed.
D-Link ShareCenter Pro 1100-04 User Manual
1
Section 1 - Product Overview
Product Overview
Package Contents
D-Link ShareCenter Pro 1100-04
CD-ROM with Manual and Software
Quick Installation Guide
Power Cord
Cat5E Ethernet Cable
Front Panel Lock Key
Note: Use the power supply that came with your device. Failure to do so might damage the unit and void the warranty.
Note: The ShareCenter Pro 1100-04 should only be maintained by authorized staf or an IT administrator. The front panel key locks the
device and keeps intruders from tampering with the device.
If any of the above items are missing, please contact your reseller.
System Requirements
For best results, the following minimum requirements are recommended on any system used to conigure and access
the ShareCenter Pro:
Computer with: 1Ghz processor / 512 MB RAM / 200 MB available space / CD-ROM drive
Internet Explorer version 7.0, Mozilla Firefox 3.0, Apple Safari, Google Chrome 3, Opera 10
Windows® XP (with Service Pack 2), Windows® Vista™ Windows® 7
3.5” SATA Hard Drive(s)
D-Link ShareCenter Pro 1100-04 User Manual
2
Section 1 - Product Overview
Features
The D-Link ShareCenter Pro 1100 is packed with a wide variety of features geared toward the small and medium business
environment. Some of these features are listed below:
Four 3.5-inch SATA Hard Drives with support for 3TB
and above
2 Gigabit Ethernet ports
2 USB 2.0 ports
UPS, printer, and external storage support
Concurrent NAS/iSCSI: Supports ile sharing and
iSCSI block devices
Data Protection: Supports RAID 0/1/5/6/5+Spare/
JBOD and S.M.A.R.T. disk diagnostic.
Ease of Use: iSCSI targets appear as a local drive on
your client PC. Access NAS iles via the easy-to-use
web ile manager.
Accessibility: Share iles across the network or over
the Internet via FTP or the web ile manager.
Security: Create users, groups, and iSCSI targets with
password authentication.
Account management: Manage users/groups and
Read/Write permission
iSNS
Virtual Disks
Thin-provisioning
DDNS
Volume Snapshot
Up to 64 iSCSI Targets
SNMP (D-View 6.0 compatible)
CHAP
D-Link ShareCenter Pro 1100-04 User Manual
�
�
�
�
�
�
�
�
�
Link Aggregation
Fail-over/Fail-back
VLAN tag Support
DFS Support
AES Support
FTP w/ TLS/SSL
NFS
ADS support
Backup
Remote backup
Local backup
External backup
PC client to NAS backup
Web File Manager
Print server
Power management to conserve energy and extend
hard drive life.
Schedule power on/of
Hard disk hibernation
SMART for hard disk health scan
D-Link Green Ethernet
Resource Monitor
Multi-LUNs per Target
Supports LUN Mapping & LUN Masking
Supports MPIO
Supports MC/S
3
Section 1 - Product Overview
�
�
�
�
�
�
�
�
Supports Windows Server 2008 Hyper-V
Network access by service
AFP support
Syslog server
Network UPS
ISO mount
WebDAV
Amazon S3
D-Link ShareCenter Pro 1100-04 User Manual
4
Section 1 - Product Overview
Hardware Overview
Front Panel
OLED Screen
OLED Button
Drive Trays
Front Panel
Lock
Power Button
COMPONENT
Front Panel Lock
DESCRIPTION
Turn the key to the up position to unlock. Turn key to left position to lock.
OLED Button
Drive Trays
Power Button
This button switches the OLED screen to display System, HD Volume Information and Error Messages.
Unclip the bays to remove the cage and install the hard drives
Use this button to switch the device on or of.
To switch on the device press the button once.
To switch of the device hold the button down for 5 seconds.
This screen displays detailed information about the following:
System Information, HD Volume Information and Error Messages
OLED Screen
D-Link ShareCenter Pro 1100-04 User Manual
5
Section 1 - Product Overview
Hardware Overview
Front Panel
Component
4 Disk LED’s
Color
Green
Red
Component
2 LAN LED’s
D-Link ShareCenter Pro 1100-04 User Manual
Status
Static
Blinking
Of
Static
Color
Blue
Description
Disk Ready
Disk being accessed
No internal disk
Disk error. Cannot Read/ Write
Status
Static
Description
A network connection is available
Blinking
Of
The network is active
The network is inactive
6
Section 1 - Product Overview
Rear Panel (Connections)
Cooling Fan
Reset Button
USB Connectors
Power Receptacle
COMPONENT
Gigabit Ethernet Port
Power Receptacle
USB Connector
Reset Button
Cooling Fan
Gigabit Ethernet Ports
DESCRIPTION
Two Gigabit Ethernet Ports to connect the ShareCenter Pro 1100-04 to the local network.
Connect the supplied power cord to the receptacle.
Two USB 2.0 (Type A) connectors. The USB Host ports are for Print Servers, USB memory disks or
USB UPS monitoring.
Press this button for more than 5 seconds to reset the unit to factory defaults.
The cooling fan is used to cool the hard drives and feature speed control.
D-Link ShareCenter Pro 1100-04 User Manual
7
Section 1 - Product Overview
Using the OLED
The ShareCenter Pro 1100-04 features an OLED that enables the administrator to easily view information about the ShareCenter
Pro. The OLED screen displays the system information, hard drive volume information and error messages. The OLED has three
diferent screens:
y
System Information- This screen shows the following information:
{
{
{
y
Hard Drive Volume information- This screen shows the following information:
{
y
The hostname of the ShareCenter Pro
The IP address of the ShareCenter Pro
The hard drive slots information
The percentage of used space on the hard drives.
Error Messages- This screen shows error messages during system failures
Press the following button
once to alternate between the diferent Status screens.
D-Link ShareCenter Pro 1100-04 User Manual
8
Section 3 - Coniguration
Chapter 1 - Hardware
The D-Link ShareCenter Pro 1100-04 is a solid NAS. It can hold four hot-swappable drives, provides auto encryption and has
dual Ethernet ports. Let’s take a closer look.
D-Link ShareCenter Pro 1100-04 User Manual
9
Section 2 - Installation
Hardware Setup - Installing Hard Drives
The D-Link ShareCenter Pro 1100 takes four 3.5” hard disk drives. The hard drives do not have to be the same size. However, to
create a RAID, it would be preferable to have all hard drives the same size. In this guide we show how to take the hard drive
cases apart, install the drives and turn on the device.
To install the Hard Drives, refer to the steps below:
tep 1: emove the hard drive cages from the
enclosure.
D-Link ShareCenter Pro 1100-04 User Manual
10
Section 2 - Installation
Hardware Setup - Removing Brackets
tep 2: emove the plastic bracket inside the hard
drive cage.
D-Link ShareCenter Pro 1100-04 User Manual
11
Section 2 - Installation
Hardware Setup - Attaching the Hard Drive to the Hard
Drive Tray
tep 3: lace a 3.5” SATA hard drive into the drive
tray, and screw it into place. There are four
holes on either side of the drive tray.
tep 4: ive trays into the enclosure.
D-Link ShareCenter Pro 1100-04 User Manual
12
Section 2 - Installation
Hardware Setup - Installing Hard Drives
tep 5: epress the blue clip in place to shut the
drive tray in the enclosure.
D-Link ShareCenter Pro 1100-04 User Manual
13
Section 2 - Installation
Network Setup - Plugging in the Network Cables
tep 1: lug in one end of the CAT5E cable (provided
in the box) into one of the Gigabyte ports at
the back of the ShareCenter Pro.
D-Link ShareCenter Pro 1100-04 User Manual
14
Section 2 - Installation
Network Setup - Plugging in the Cables
tep 2: lug the other end of the CAT5E cable into a
router or switch.
D-Link ShareCenter Pro 1100-04 User Manual
15
Section 2 - Installation
Power Cable Setup - Plugging in the Cables
tep 1: lug the power cord into the back of the
ShareCenter Pro 1100-04.
tep 2: lug the other end into the wall socket and
power up the device.
D-Link ShareCenter Pro 1100-04 User Manual
16
Section 2 - Installation
Powering on the Device
Before connecting to the ShareCenter Pro 1100-04, test to see if the device is powered on correctly.
tep 1:
o not slot any of the hard drive bays into the
tep 2:
ress the “On” button in front of the
ShareCenter Pro.
ShareCenter Pro and wait for the OLED
screen to display “Welcome to ShareCenter
Pro “1100”. There will also be a blinking blue
network LED that indicates the device is
connected to the network.
Power Button
OLED Screen
Network LED
D-Link ShareCenter Pro 1100-04 User Manual
17
Section 2 - Installation
Powering on the Device - Software
tep 3: lace the accompanied CD-ROM into your
CD-ROM drive and browse to D-Link’s DNS1100-04 EZSearch. Double-click the icon to
activate the program.
tep 4: his starts the EZSearch utility. The EZSearch
utility locates the ShareCenter Pro 1100-04
and it’s IP address.
D-Link ShareCenter Pro 1100-04 User Manual
18
Section 3 - Coniguration
Chapter 2 - Software Installation
The D-Link ShareCenter Pro 1100-04 is a solid NAS. Installing, coniguring, and creating shares on the ly is the ShareCenter Pro’s strengths. Let’s
take a closer look.
D-Link ShareCenter Pro 1100-04 User Manual
19
Section 2 - Installation
Software Setup - Default IP Address Location
During the initial boot sequence, the ShareCenter Pro 1100-04 awaits to be assigned a DHCP IP address. If it does not receive
a DHCP assigned IP address, the ShareCenter Pro 1100 reverts to its Auto-IP address. The Auto-IP address will look similar to
(eg. 169.254.x.x). The Username and Password information is just below the IP address information.
Username
Password
It is recommended to use the D-Link EZ Search Utility when accessing and coniguring the ShareCenter Pro for the irst time.
If you want to change the IP address before logging in or are unable to connect to the ShareCenter Pro’s IP address, you can
use the EZ Search Utility provided on the product CD to locate the device on your network and make any changes.
D-Link ShareCenter Pro 1100-04 User Manual
20
Section 2 - Installation
Software Setup - EZ Search Utility
Here is a closer look at the EZ Search Utility
work
Storage
Device
efresh
!oniguration
ƒAN
‹pply
"#!#$ %rive
The EZ Search Utility displays any D-Link NAS or ShareCenter Pro
device on the network here.
Click Refresh to refresh the device list.
Click Coniguration to access the Web based coniguration of the
ShareCenter Pro.
Conigure the LAN Settings for the ShareCenter Pro here.
Click Apply to save changes to the LAN Settings.
Displays the available iSCSI targets on the ShareCenter Pro.
Mapping
!onnect
anagement
%rive Mapping
‹vailable
Drive Letters
‹bout
&"
Click Connect to connect to the iSCSI target.
Click Management to edit the information.
Volumes available for mapping are displayed here.
Choose an available drive letter. Click Connect to map the selected
volume. Click Disconnect to disconnect the selected mapped
volume.
Click About to view the software version of the Easy Search Utility.
Click Exit to close the utility.
D-Link ShareCenter Pro 1100-04 User Manual
21
Section 3 - Coniguration
Getting Started
To run the EZ Search Utility, insert the ShareCenter Pro CD into your CD-ROM drive:
'tep 1: ()*+, -./ EZ Search Utility link.
Click EZ Search Utility.
D-Link ShareCenter Pro 1100-04 User Manual
22
Section 3 - Coniguration
0tep 2:
12345 Coniguration to the right of the
Network Storage Device.
The Coniguration button launches your computer’s default
web browser and directs it to the IP address listed for the
device. Make sure your browser is not conigured to use a
proxy server.
Note: The computer used to access the web-based
coniguration manager must be on the same subnet as the
ShareCenter Pro. If your network is using a DHCP server and
the computer receives IP settings from the DHCP server, the
ShareCenter Pro will automatically be in the same subnet.
D-Link ShareCenter Pro 1100-04 User Manual
23
Section 2 - Installation
Getting Started - Browser Setup
Alternatively, open your default browser and type in the IP address of your ShareCenter Pro 1100-04.
D-Link ShareCenter Pro 1100-04 User Manual
24
Section 3 - Coniguration
The Login screen will appear:
Select System Administrator and
leave the password ield blank.
Note: The computer used to access the web-based
coniguration manager must be on the same subnet as the
ShareCenter Pro. If your network is using a DHCP server and
the computer receives IP settings from the DHCP server, the
ShareCenter Pro will automatically be in the same subnet.
Click Login.
6tep 3: 789:; <=> ?@<<on next to System
Administrator, leave the Password ield
blank and click Login.
D-Link ShareCenter Pro 1100-04 User Manual
25
Section 3 - Coniguration
Using the Web UI
The screen loads to the default page. If there are no drives, the browser loads to the Disk Management, Volumes page.
D-Link ShareCenter Pro 1100-04 User Manual
26
Section 3 - Coniguration
Using the Web UI Part II
Load the hard drives into the bays. Once the bays are installed, the Create Volume window appears but this only occurs if no
RAID has been created. The ShareCenter Pro 1100-04 immediately recognizes the capacity of the drive(s) and prompts you
to select a RAID level. See Creating Your First Volume in the next section. You can also close this window and use the Setup
Wizard to conigure the ShareCenter Pro 1100-04.
Note: If there is only one drive
installed into the system, the device
will act as a standalone drive as no
RAID can be created.
D-Link ShareCenter Pro 1100-04 User Manual
27
Section 3 - Coniguration
Understanding the Web UI
Once a volume has been created, the Web UI defaults to the Homepage ( ). The main categories for coniguring the ShareCenter
Pro 1100-04 are located in the folders at the left of the page. Click the icon to see the categories of each folder. The categories
available for coniguration include: Homepage, Status, Disk Management, Account Management, System Management, Network
Services, Applications, Backup and Extension Pack.
D-Link ShareCenter Pro 1100-04 User Manual
28
Section 3 - Coniguration
Understanding the WEB UI Part II
The following is a short explanation of the Web UI:
y
y
y
y
y
y
y
y
y
Homepage- Contains the System Wizard, Create User, Create Share Folder and My Favorites.
Status- Contains the System Status, Hard Drive Status, and Resource Monitor.
Disk Management- Allows the ShareCenter Pro administrator to create/conigure a Volume, iSCSI Target, Virtual Volume,
and perform Disk Diagnostic.
Account Management- Allows the ShareCenter Pro administrator to conigure Admin Password, Users, Groups and Share
Folders
System Management- Contains Network, Time and Date, System Settings, Power Management, Email Alerts, Firmware
Upgrade and Logs.
Network Services- Contains File Sharing, Dynamic DNS, SNMP and Network Discovery Services.
Applications- Contains Web File Manager and Download Management.
Backup- Contains Volume Snapshot, Local Backup, Remote Backup and External Backup.
Extension Pack- Allows the ShareCenter Pro administrator to add more applications to the device and supports several
Multi-language packs.
These pages and their coniguration options will be discussed in detail in the following pages of this manual.
Note: After logging in to the ShareCenter Pro for the irst time it is recommended to add a password to the admin account.
D-Link ShareCenter Pro 1100-04 User Manual
29
Section 3 - Coniguration
Chapter 3 - Setup Wizard
The ShareCenter Pro 1100-04 provides a Setup Wizard to easily conigure the DNS-1100-04. This chapter shows you how to
create volumes and format drives.
D-Link ShareCenter Pro 1100-04 User Manual
30
Section 3 - Coniguration
Using the Setup Wizard for the First Time
The Setup Wizard is the easiest and fastest way to setup your ShareCenter Pro 1100-04. Once you have entered your IP address
into the browser, follow these few steps to get started:
Create Volume (close)
Atep 1: BCDEF GHF Breate Volume window.
D-Link ShareCenter Pro 1100-04 User Manual
31
Section 3 - Coniguration
Using the Setup Wizard for the First Time
Itep 2: JKLMN OPQ Home icon at the top right of the
browser.
Home Icon
D-Link ShareCenter Pro 1100-04 User Manual
32
Section 3 - Coniguration
Using the Setup Wizard for the First Time
Rtep 3: STUVW XYZ Setup Wizard icon on the main
Homepage
System Wizard Icon
D-Link ShareCenter Pro 1100-04 User Manual
33
Section 3 - Coniguration
Using the Setup Wizard for the First Time
[tep 4: \he ShareCenter Pro 1100-04 System Wizard
starts. Read the instructions carefully and
click Next.
Next
D-Link ShareCenter Pro 1100-04 User Manual
34
Section 3 - Coniguration
Using the Setup Wizard for Static IP Addresses
]tep 5: ^he ShareCenter Pro 1100-04 System
Wizard provides information on setting
up your local LAN, VLAN, and Port
Bonding.
Enter the Static IP address, Subnet
Mask, Jumbo Frame, and Gateway
details provided by your systems
administrator. Leave Jumbo Frame
Disabled if your Service Provider does
not support it.
Setup the VLAN settings according to
your virtual LAN.
Enable Port Bonding according to your
speciied needs.
Click Next to continue.
Note: If your network environment
is setup with DHCP, select DHCP. If,
however, you are setting up your
network environment using your own
set of IP addresses, select Static IP.
D-Link ShareCenter Pro 1100-04 User Manual
35
Section 3 - Coniguration
Using the Setup Wizard for Static IP Addresses
_tep 6: `he ShareCenter Pro 1100-04 System
Wizard provides information on
setting up your second local LAN,
VLAN, and Port Bonding too.
Enter the Static IP address, Subnet
Mask, Jumbo Frame, and Gateway
details provided by your systems
administrator. Leave Jumbo Frame
Disabled if your Service Provider does
not support it.
Setup the VLAN settings according to
your virtual LAN.
Click Next to continue.
Note: If you are not coniguring the
ShareCenter Pro to use the second
LAN port, click DHCP Client.
D-Link ShareCenter Pro 1100-04 User Manual
36
Section 3 - Coniguration
Using the Setup Wizard for Host Names
atep 7: bhe ShareCenter Pro 1100-04 System
Wizard allows you to change the
hostname. Enter the Host Name,
Primary DNS and Secondary DNS, and
the Default Gateway for either LAN
card.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
37
Section 3 - Coniguration
Using the Setup Wizard for File Sharing
ctep 8: dhe ShareCenter Pro 1100-04 System Wizard
allows you to select the ile sharing protocols.
Click Enable or Disable to activate or
deactivate these share options.
CIFS: Common Internet File System, provides
shared access to iles, printers, and serial ports.
FTP: File Transfer Protocol, provides is used to
copy a ile from one host to another.
NFS: Network File System, allows a client
computer to access iles over the network as if
the device is part of local storage.
DFS: Distributed File System, is a remote
ile access protocol that provides faster
performance over slower networks.
Quota: Provides disk and network quotas
based on user’s setting.
AFP: Apple Filing Protocol, is a network
protocol that ofers ile services for Mac OS X
and previous Mac OS’s.
WebDAV: Web-based Distributed Authoring
and Versioning,is a set of methods based on
the Hypertext Transfer Protocol (HTTP).
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
38
Section 3 - Coniguration
Using the Setup Wizard for RAID Levels
etep 9: fhe ShareCenter Pro 1100-04 System
Wizard automatically detects the
amount of hard drives present and
creates a table to select which drives
you want.
In our example, we inserted one drive.
The RAID level is automatically selected
(standalone).
Select the Disk Array and click Next.
D-Link ShareCenter Pro 1100-04 User Manual
39
Section 3 - Coniguration
Encrypting your Drive
gtep 10: hijkl Create Volume, Settings choose to
encrypt your hard drive. Enter a Password
and re-enter to conirm your Password.
Select Auto Unlock to unlock the hard drive
on powering the NAS or select USB Key to
save the password on an external USB drive.
Click Apply.
Password Field
Note: Select either Auto Unlock or USB Key.
You cannot select both.
Auto Unlock Checkbox
USB Key Checkbox
D-Link ShareCenter Pro 1100-04 User Manual
40
Section 3 - Coniguration
Setup Wizard Summary
mtep 11: nhe ShareCenter Pro 1100-04 now
provides a summary of all the stages
you completed.
LAN 1
LAN 2
D-Link ShareCenter Pro 1100-04 User Manual
41
Section 3 - Coniguration
Setup Wizard Summary Part II
otep 12: phe ShareCenter Pro 1100-04 now provides a
summary of all the stages you completed.
Global Settings
File Sharing
Create Volume
Click Apply to continue.
D-Link ShareCenter Pro 1100-04 User Manual
42
Section 3 - Coniguration
Creating a Clean Volume
qtep 13: rstuv Yes to create a new Volume on the
drive. All data on the selected disk will be
erased.
qtep 14: whe ShareCenter Pro 1100-04 now creates a
volume for the hard drive.
D-Link ShareCenter Pro 1100-04 User Manual
43
Section 3 - Coniguration
Formatting a Volume
xtep15: yz{e the Volume is created, the ShareCenter
Pro 1100-04 will format the drive. (As shown
below)
D-Link ShareCenter Pro 1100-04 User Manual
44
Section 3 - Coniguration
Accessing the Drive for the First Time
When the Setup Wizard is complete, use your Windows Explorer to access the drives on the ShareCenter Pro 1100-04.
D-Link ShareCenter Pro 1100-04 User Manual
45
Section 3 - Coniguration
Chapter 4 - Hardware - Installing more Drives
The D-Link ShareCenter Pro 1100-04 can take up to four hard drives. All these hard drives can be individually conigured and
grouped in an array for RAID. Let’s take a look further.
D-Link ShareCenter Pro 1100-04 User Manual
46
Section 3 - Coniguration
Hardware - Installing more Drives
Installing new hard drives in the ShareCenter Pro 1100 is convenient and funtional. Let’s take a look at this in more detail.
|tep1: •hen you irst purchase the ShareCenter
Pro 1100, there are no drives in it. The Setup
Wizard will prompt you to install drives (as
seen below).
Click OK and install the drives.
D-Link ShareCenter Pro 1100-04 User Manual
47
Section 3 - Coniguration
Hardware - Installing more Drives
}tep 2: ~nstall the irst drive
}tep 3: he top OLED indicates the position of
the drive on the ShareCenter Pro, while
the bottom OLED displays the active drive
number in green.
Top OLED
Bottom OLED
D-Link ShareCenter Pro 1100-04 User Manual
48
Section 3 - Coniguration
Hardware - Installing more Drives
€tep 4: nstall the second drive
Hard Drive Installation
€tep 5: ‘s you install the second drive, the
ShareCenter Pro automatically recognizes
the drives and displays the information on
the OLED screens.
Top OLED showing
two drives
Bottom OLED showing
drive numbers
D-Link ShareCenter Pro 1100-04 User Manual
49
Section 3 - Coniguration
Chapter 5 - Software - Creating Volumes & Formatting
The D-Link ShareCenter Pro 1100-04 handles each drive diferently. Once a new drive is installed the WEB UI creates a volume
and formats the drive according to the user’s requirements. Let’s take a closer look.
D-Link ShareCenter Pro 1100-04 User Manual
50
Section 3 - Coniguration
Software - Installing more Drives
Once the hard drives are installed in the ShareCenter Pro 1100-04, the drives can be formatted and conigured.
‚tep1: „…†‡ ˆour default browser and type in the
IP Address displayed on the OLED screen.
Browser window
LED IP Address
If you cannot see the top OLED screen click the
icon on the right side of the ShareCenter Pro.
D-Link ShareCenter Pro 1100-04 User Manual
Touch Display
51
Section 3 - Coniguration
Software - Coniguring more than one drive
‰tep 2:
The Login screen will appear:
Select System Administrator and
leave the password ield blank.
Note: The computer used to access the web-based
coniguration manager must be on the same subnet as
the ShareCenter Pro. If your network is using a DHCP
server and the computer receives IP settings from the
DHCP server, the ShareCenter Pro will automatically be
in the same subnet.
Click Login.
‰tep 3: ŠŒŽ’“ ”–— ˜™””on next to System
Administrator, leave the Password ield
blank and click Login.
D-Link ShareCenter Pro 1100-04 User Manual
52
Section 3 - Coniguration
Software - Coniguring more than one drive
štep 4: ›œžŸ Disk Management, Disk Diagnostics
Disk Diagnostics shows all the drives placed
in the NAS (formatted or unformatted)
D-Link ShareCenter Pro 1100-04 User Manual
53
Section 3 - Coniguration
Software - Creating RAID
tep 5: ¡¢£¤¥ Disk Management click
Volume. The Create Volume
window appears.
tep 6: ¡¢£¤¥ Create Volume, select the
RAID Level best suited for your
purpose. (See More About RAID
in other chapters)
tep 7: ¦elect the Array you wish to use
and click Next.
D-Link ShareCenter Pro 1100-04 User Manual
54
Section 3 - Coniguration
Software - Encryption Settings
The ShareCenter Pro 1100-04 ofers bootup encryption and remote encryption via a USB stick drive. Select the method that
best suits your needs.
§tep 8: ¨elect Auto-rebuild to automatically unlock the
Select to enable or disable the auto-rebuild
function of RAID 1, RAID 5, or RAID 6
volume on startup.
Select Encryption to encrypt the device
Type a Password for encryption.
§tep 9: ©ª«¬­ Apply to continue.
Click the Enable radio button to encrypt the
volumes. Enter a password in the Password and
Conirm Password ields.
Tick the Auto Unlock check box to automatically
unlock the volume when the system starts.
Tick the USB Key check box to save the password
to a USB drive.
Click Apply to continue.
D-Link ShareCenter Pro 1100-04 User Manual
55
Section 3 - Coniguration
Software - Creating the Volume
®tep 10: ¯°±²³ Yes to create the Volume.
A warning message appears before starting to
create the volume.
Click Yes to continue.
The volume is being created. The status bar
displays the percentage of completion in real
time.
D-Link ShareCenter Pro 1100-04 User Manual
56
Section 3 - Coniguration
Software - Creating the RAID & Formatting
´tep 11: µ¶·e the Volume is created,
the ShareCenter Pro 1100-04
formats the drives and creates
the RAID.
Note: The ShareCenter Pro
1100-04 will automatically
create the Volume, a
Standalone Volume, if the
size of the hard drives are
diferent.
Once the volume is created, the Volume
page opens to show the information.
D-Link ShareCenter Pro 1100-04 User Manual
57
Section 3 - Coniguration
Software - Volume & RAID Created
The ShareCenter Pro 1100-04 creates a Volume and conigures the RAID. Windows Explorer can see the share but users on the
network cannot access it unless a shared folder is created.
D-Link ShareCenter Pro 1100-04 User Manual
58
Section 3 - Coniguration
Chapter 6 - Software - Creating Users
The D-Link ShareCenter Pro 1100-04 allows you to create individual accounts or group accounts accordingly. Let’s take a look.
D-Link ShareCenter Pro 1100-04 User Manual
59
Section 3 - Coniguration
Software - Creating Users
¸tep 1: ¹º»e you have logged into
the Web UI, click the Home
icon on the left side of the
browser.
Click the Create User icon.
Click Create User
D-Link ShareCenter Pro 1100-04 User Manual
60
Section 3 - Coniguration
Software - Creating Users
¼tep 2: ½he “Create User” wizard
appears.
Click Next to proceed.
Click the Create User icon in the Homepage window
and the Create User window appears.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
61
Section 3 - Coniguration
Software - User Information
¾tep 3: ¿Àter the User Name and Password in
the ields provided.
Conirm the Password entered.
¾tep 4: ¿Àter a storage size in
megabytes if you wish to limit
a user’s storage quota.
Click Next to continue
Enter a name in User Name, and a
password in Password and Confirm
Password.
If setting a speciic storage quota for the user,
tick the Set Quota check box and enter the
storage quota in megabytes (MB).
If you use 0 in the Quota it represents
unlimited disk space.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
62
Section 3 - Coniguration
Software - Creating Groups
Átep 5: ÂÃÄÅÆ Group List, view the groups you wish the user to
belong to.
Click Next to continue.
If there is no Group List just click Next and you can add
Groups at a later stage
Select a group from the list. If there is no entry in
the list, you can go to Account Management >>
User to update the information after a group has
been created.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
63
Section 3 - Coniguration
Software - Creating Share Folder Lists
Çtep 6: ÈÉÊËÌ Share Folder List, view the shared folder you wish
the user to belong to.
Click Next to continue.
If there is no Share Folder List just click Next and you can
add the Folder at a later stage.
Select a share folder from the list. If there is no entry
in the list, you can go to Account Management >
User to update the information after a share folder
is created.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
64
Section 3 - Coniguration
Software - User Summary
Ítep 7: ÎÏÐÑÒ Summary, view details about the user
you have just created.
Click Apply to save the settings.
This window displays the information that has
been conigured.
Click Apply to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
65
Section 3 - Coniguration
Software - User Information
Ótep 8: ÔÕÖ×Ø Account
Management, Users.
There you will ind the
New User that you have
created.
Account Manager
Users
New User
D-Link ShareCenter Pro 1100-04 User Manual
66
Section 3 - Coniguration
Software - Creating more than One User
Ùtep 1: ÚÛÜe you have
the Account
Management window
open, simply click
Create at the top of
the right window
pane.
Create
D-Link ShareCenter Pro 1100-04 User Manual
67
Section 3 - Coniguration
Software - Creating more than One User
Ýtep 2: Þßter the details of the new user and
click Next.
New User details
D-Link ShareCenter Pro 1100-04 User Manual
68
Section 3 - Coniguration
Software - Creating more than One User
àtep 3: áâãäå Group List, view the groups you wish the user
to belong to.
Click Next to continue.
If there is no Group List just click Next and you can
add Groups at a later stage
Select a group from the list. If there is no entry in
the list, you can go to Account Management >>
User to update the information after a group has
been created.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
69
Section 3 - Coniguration
Software - Creating more than One User
ætep 4: çèéêë Share Folder List, view the shared folder
you wish the user to belong to.
Click Next to continue.
If there is no Share Folder List just click Next and
you can add the Folder at a later stage
Select a share folder from the list. If there is no entry
in the list, you can go to Account Management >
User to update the information after a share folder
is created.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
70
Section 3 - Coniguration
Software - User Summary
ìtep 5: íîïðñ Summary, view details about the
user you have just created.
Click Apply to save the settings.
This window displays the information that has
been conigured.
Click Apply to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
71
Section 3 - Coniguration
Software - User Information
òtep 6: óôõö÷ Account Management,
Users.
There you will ind the New
User that you have created.
Account Manager
Users
Second User created
D-Link ShareCenter Pro 1100-04 User Manual
72
Section 3 - Coniguration
øtep 1: ùúûüý þÿ check-box next to
Software - Deleting a User
the User’s name and click
Delete.
Check-box next to User
details.
D-Link ShareCenter Pro 1100-04 User Manual
73
Section 3 - Coniguration
Software - Deleting a User
tep 2: onirm that you want to
delete the User from the User
List and click Yes.
tep 3: he User no longer exists in the User List.
D-Link ShareCenter Pro 1100-04 User Manual
74
Section 3 - Coniguration
Software - Importing Users
tep 1: Import
Users button
at the top of
the Account
Management,
Users window.
Click Import Users
D-Link ShareCenter Pro 1100-04 User Manual
75
Section 3 - Coniguration
Software - Importing Users
tep 2: he welcome window is displayed. Click
Next to continue.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
76
Section 3 - Coniguration
Software - Importing Users - Creating a User List
tep 3: ownload button to see an example .txt
ile. The ile looks similar to this:
#user name;user password;user groups;
shared folder(rw); shared folder(ro); shared
folder(deny);user quota
user001;11111;Group1,Group2;Volume_1,Volume
_50;B,Volume_51;;10240
Note: Consult a systems administrator or a
programmer to design the script for this ile.
Note: The ShareCenter Pro only accepts “txt” iles at
the moment.
tep 4: x next to Overwrite duplicate
accounts to write over user accounts you already
have in the ShareCenter Pro.
tep 5: Browse button to locate the ile you
created and click Next.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
77
Section 3 - Coniguration
Software - Importing Users - Checking the User List
tep 6: his window displays all the users in the ile. If there
are any error warnings in the State ield, the user
will not be able to go to the next window.
Click Next to continue.
tep 7: he window displays the inal results of importing
users to the ShareCenter Pro.
Click Apply to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
78
Section 3 - Coniguration
Software - Creating a Batch User List
tep 1: !" #$% Create Batch button at the top of the
Account Management, Users window.
Click Create Batch
D-Link ShareCenter Pro 1100-04 User Manual
79
Section 3 - Coniguration
Software - Creating a Batch User List
&tep 2: 'he welcome window appears. Click Next to
continue.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
80
Section 3 - Coniguration
Software - Creating a Batch User List
(tep 3:
,his window allows you to create multiple users.
User Name Preix
(tart Number
)reate Number
Enter the preix of the users
Enter the start number of the users.
Enter the total number of the users.
*assword Enter the password of the users
)onirm Retype the password
Password
+verwrite
duplicate
Accounts
(et Quota
Tick the check box to replace duplicate accounts.
Tick the Set Quota check box to limit the storage
capacity (in megabyte) for the user. The value of
0 means an unlimited quota size.
Click Next to continue
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
81
Section 3 - Coniguration
Software - Creating a Batch User List
-tep 4:
This window is used to add the users to groups. If there is no entry in the list, you can go to Account Management > Groups
to create groups.
-earch Enter the search keyword and click
‹dd
.age
to search for
the group. Click
to clear the search ield and all
groups’ information appears.
Tick the corresponding check box to add the users
to the groups.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or
Last page ( ) to search for the group.
/efresh Click
to update the group list.
Click Next to continue.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
82
Section 3 - Coniguration
Software - Creating a Batch User List
0tep 5:
This window is used to assign access rights to the users for the corresponding share folder(s) to the share folders. If there is no
entry in the list, you can go to Account Management > Share Folders to create share folders.
0earch Enter the search keyword and click
1ead Only
1ead/Write
23y
to search for
the folder. Click
to clear the search ield and all
folders appear.
Tick the check box for read only access right.
Tick the check box for both read
and write access rights.
Tick the check box for no access right.
4age Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or
Last page ( ) to search for the group.
1efresh Click
to update the folder list.
Click Next to continue.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
83
Section 3 - Coniguration
Software - Creating a Batch User List
5tep 6:
This window displays a summary of the conigured information.
Click Previous to modify the settings.
Click Apply to save the settings. Depending on the amount
of users, the procedure may take a few hours.
Click Apply to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
84
Section 3 - Coniguration
Chapter 7 - Software - Creating a Shared Folder
The D-Link ShareCenter Pro 1100-04 allows you to create shared folders for users to access. Let’s take a look.
D-Link ShareCenter Pro 1100-04 User Manual
85
Section 3 - Coniguration
Software - Creating a Shared Folder
6tep 1: ƒ78e you have logged into
the Web UI, click the Home
icon on the left side of the
browser.
Click the Create Share Folder
icon.
Click Create Share
Folder
D-Link ShareCenter Pro 1100-04 User Manual
86
Section 3 - Coniguration
Create Share Folder
9tep 2: :he Create Share Folder introduction window
appears. Click Next to continue.
Click the Create Share Folder icon in the Homepage
window and the Create Share Folder window appears.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
87
Section 3 - Coniguration
Create Share Folder - Volumes & Quotas
;tep 3: <=>?@ Volume Path, click
on the Select Path ield to
choose a folder.
;tep 4: ABCCD? EB? Volume you wish
to use by double-clicking or
click Create.
Click the
Select Path ield to choose the path of a folder.
Click Create
D-Link ShareCenter Pro 1100-04 User Manual
88
Section 3 - Coniguration
Create Share Folder - Volumes & Quotas
Ftep 5: ŠGter a Share Folder name in the
ield provided and click OK.
D-Link ShareCenter Pro 1100-04 User Manual
89
Section 3 - Coniguration
Create Share Folder - Volumes & Quotas
Htep 6: IJKe the Share Folder name
is chosen, select one or all of
the Share Folder Options.
Click the radio buttons to conigure the folder
options.
Lplocks are: guarantees made by a server for
a shared logical volume to its clients. These
guarantees inform the Client that a ile’s
content will not be allowed to be changed
by the server, or if some change is imminent,
the client will be notiied before the change is
allowed to proceed.
Select Enable or Disable according to your
choice.
D-Link ShareCenter Pro 1100-04 User Manual
90
Section 3 - Coniguration
Create Share Folder - Volumes & Quotas
Mtep 6: ap Archive: means that backed up data is
kept in a ile that lists what iles were backed up
and on what dates. It compares ile modiication
dates and maps data to that archive.
Click the Set Quota box and enter a number in
Megabytes
D-Link ShareCenter Pro 1100-04 User Manual
91
Section 3 - Coniguration
Create Share Folder - Volumes & Quotas
Ntep 6: Oecycle Bin is: means that any iles within
the Share Folders can be deleted and
placed in the Recycle Bin. If this is disabled
then a user cannot delete an item into the
Recycled Bin.
Click the Set Quota box and enter a number in
Megabytes
D-Link ShareCenter Pro 1100-04 User Manual
92
Section 3 - Coniguration
Create Share Folder - Volumes & Quotas
Ptep 7: QRSTU VWX Set Quota check box and type
the storage amount in megabytes.
Click Next to continue.
If setting a speciic storage quota for the
share folder, tick the Set Quota check box
and enter the storage quota in megabyte
(MB).
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
93
Section 3 - Coniguration
Create Share Folder - Select Service
Ytep 8: Zelect the Service you wish to enable.
There are six services: CIFS, AFP, FTP, NFS,
Web File Manager, and WebDAV.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
94
Section 3 - Coniguration
Create Share Folder - Access Rights
[tep 8: \elect All Users or Speciic
User. Click Next to continue.
Use the radio button to select All Users or
Speciic User
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
95
Section 3 - Coniguration
Create Share Folder - Access Rights
]tep 9: ^elect the Access Rights of the folder.
Read Only: Give the users read only access.
Read/Write: Give the users read and write
access to the folder
Deny: Deny the user from accessing the
shared folder.
Click Next to continue.
Select either Read Only, Read/Write, or Deny.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
96
Section 3 - Coniguration
Shared Folders
_tep 10: `he Summary window appears detail the
events you just conigured.
Click Apply when done.
Summary Report
Click Apply to continue.
D-Link ShareCenter Pro 1100-04 User Manual
97
Section 3 - Coniguration
Create Share Folder - Summary
atep 11: bcdef Account Management,
Shared Folders. The newly created
Shared Folder appears in the
right-hand pane.
Shared Folder
Usage/Size
Status Options
Management
D-Link ShareCenter Pro 1100-04 User Manual
98
Section 3 - Coniguration
Chapter 8 - Software - Creating a Group
The D-Link ShareCenter Pro 1100-04 allows you to create groups for users/shared folders to access. Let’s take a look.
D-Link ShareCenter Pro 1100-04 User Manual
99
Section 3 - Coniguration
Software - Creating a Group
gtep 1:
hije logged in click Account
Management, then Groups.
D-Link ShareCenter Pro 1100-04 User Manual
100
Section 3 - Coniguration
Software - Creating a Group
ktep 2:
lmnop Create.
Click Create
D-Link ShareCenter Pro 1100-04 User Manual
101
Section 3 - Coniguration
Software - Creating a Group
qtep 3:
rstuv Group Name type in the name of the
group and click Next
Enter a Group Name
Click Next to continue
D-Link ShareCenter Pro 1100-04 User Manual
102
Section 3 - Coniguration
Software - Adding Users to a Group
wtep 4:
‘dd Users to the Group. Click the checkbox next to the name of the user.
Add a User to the Group
Click Apply to
save the changes.
D-Link ShareCenter Pro 1100-04 User Manual
103
Section 3 - Coniguration
Software - Adding Users to a Group
xtep 5: yfter the changes are
applied, the ShareCenter Pro
reverts back to the Accounts
Management, Groups
window.
The new Group is created with
information on the users
Group Name
Users added to
the Group
D-Link ShareCenter Pro 1100-04 User Manual
104
Section 3 - Coniguration
My Favorites
Click the (Homepage) icon to see the My Favorites ield at the lower half of the window. To add a category in My Favorites,
click an arrow key next to a folder icon to display all categories within the folder in the left window, and drag the category to
the My Favorites ield. To delete a category in My Favorites, drag the category in My Favorites ield to the left window. Once
the category is added to My Favorites, click the icon to see the category in the list. Click to directly link to the window of the
category.
D-Link ShareCenter Pro 1100-04 User Manual
105
Section 3 - Coniguration
Chapter 9 - Software - Admin Password
The D-Link ShareCenter Pro 1100-04 allows you to create and change the Administrator Password. Let’s take a look.
D-Link ShareCenter Pro 1100-04 User Manual
106
Section 3 - Coniguration
Software - Admin Password
ztep 1: {og into the ShareCenter Pro.
Click Account Management,
then click Admin Password.
Click Admin Password
D-Link ShareCenter Pro 1100-04 User Manual
107
Section 3 - Coniguration
Software - Admin Password
|tep 2: }~ter a Username, the original password. Then the New Password and retype that password again in the ields provided.
€ser Name Displays administrator’s user name.
assword Enter the original password.
‚w Enter a new password.
Password
„onirm
Password
Retype the new password.
Click Apply to continue.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
108
Section 3 - Coniguration
Software - Admin Password
…tep 3: † ‡onirmation window
appears to inform you that
the changes have been
saved.
Click OK
D-Link ShareCenter Pro 1100-04 User Manual
109
Section 3 - Coniguration
Chapter 10 - Software - System & Hard Drive Status
The D-Link ShareCenter Pro 1100-04 allows you to check the status of your machine through the web UI. Let’s take a look.
D-Link ShareCenter Pro 1100-04 User Manual
110
Section 3 - Coniguration
Software - Status Management
ˆtep 1: ‰ŒŽ’ “”• Status Folder
icon in the left pane of the
ShareCenter Pro 1100-04. It
reveals System Status, Hard
Drive Status, and Resource
Monitor.
D-Link ShareCenter Pro 1100-04 User Manual
111
Section 3 - Coniguration
Software - System Status
–tep 2: —˜™š› œž System Status
icon.
Click the System
Status icon
D-Link ShareCenter Pro 1100-04 User Manual
112
Section 3 - Coniguration
Software - System Status
Ÿtep 3: he Status, System Status
information window pane
provides Basic Information,
LAN 1 & 2 information,
Network Settings, and Date
and Time Settings.
D-Link ShareCenter Pro 1100-04 User Manual
113
Section 3 - Coniguration
System Status
¡asic
Information
¢AN Info
£¤¥work
Settings
¦§te and
Time
¨©¡ ¦isk
Information
Displays the model name, current irmware version and current temperature of the ShareCenter Pro.
Displays the local network settings of the ShareCenter Pro
Displays the host name, and DNS information of the ShareCenter Pro
Displays the current date and time settings of the ShareCenter Pro.
Displays information for a connected USB printer, memory disk or UPS. Click the Unmount button to remove the device
from the ShareCenter Pro.
D-Link ShareCenter Pro 1100-04 User Manual
114
Section 3 - Coniguration
Software - Hard Drive Status
ªtep 1: «¬­®¯ °±² Status Folder
icon in the left pane of the
ShareCenter Pro 1100-04
D-Link ShareCenter Pro 1100-04 User Manual
115
Section 3 - Coniguration
Software - Hard Drive Status
³tep 2: ´µ¶·¸ ¹º» Hard Drive Status
icon in the right pane
Click the Hard
Drive Status icon
D-Link ShareCenter Pro 1100-04 User Manual
116
Section 3 - Coniguration
Software - Hard Drive Status
¼tep 3: ½his window displays the
Vendor, Model name,
Temperature, and Size of
the hard disks installed in the
ShareCenter Pro, along with
the slot they are installed in.
D-Link ShareCenter Pro 1100-04 User Manual
117
Section 3 - Coniguration
Software - Hard Drive Status
¾tep 4: ¿ouble-click each hard
drive to view the S.M.A.R.T.
information
The S.M.A.R.T. information
for the selected hard drive
is displayed. Click the Close
button to go back to the
Hard Drive Status window.
Click the
window.
to close the
D-Link ShareCenter Pro 1100-04 User Manual
118
Section 3 - Coniguration
Software - Resource Monitor
Àtep 1: ÁÂÃÄÅ ÆÇÈ Status Folder
icon in the left pane of the
ShareCenter Pro 1100-04
D-Link ShareCenter Pro 1100-04 User Manual
119
Section 3 - Coniguration
Software - Resource Monitor
Étep 2: ÊËÌÍÎ ÏÐÑ Resource Monitor
icon in the right pane.
Click the Resource
Monitor icon
D-Link ShareCenter Pro 1100-04 User Manual
120
Section 3 - Coniguration
Software - Resource Monitor
Òtep 3: Another Status utility is the Resource Monitor. It has ive informational screens: CPU Usage, Disk Usage, Memory Usage, Bandwidth
Usage, and Process.
ÓÔÕ Õsage Shows what percentage of data
is being used for the CPU.
Öisk Usage Shows the used space, the
available space, and the total
space.
The iSCSI Target Used Size will be
displayed when iSCSI LUNs are
created
D-Link ShareCenter Pro 1100-04 User Manual
121
Section 3 - Coniguration
Software - Resource Monitor
×tep 4: Øemory Shows how much memory is being consumed.
Usage
Ùandwidth Shows data transfer on 2 LAN ports.
Usage
D-Link ShareCenter Pro 1100-04 User Manual
122
Section 3 - Coniguration
Ûtep 5:
Úrocess This table shows PID, User, Memory, CPU Usage, and
Command data information.
D-Link ShareCenter Pro 1100-04 User Manual
123
Section 3 - Coniguration
Chapter 11 - Software - Disk Management
The D-Link ShareCenter Pro 1100-04 allows you to manage various aspects of the machine - primarily the disks. Let’s take
a look.
D-Link ShareCenter Pro 1100-04 User Manual
124
Section 3 - Coniguration
Software - Disk Management
Ütep 1: ÝÞßàá âãä Disk Management Folder icon in the left pane of the ShareCenter Pro 1100-04
D-Link ShareCenter Pro 1100-04 User Manual
125
Section 3 - Coniguration
Software - Disk Management
åtep 2: æçèéê ëìí Volume
icon.
Click the Volume icon
D-Link ShareCenter Pro 1100-04 User Manual
126
Section 3 - Coniguration
Software - Disk Management - Volume
îtep 3: ïhen you click a volume
the ShareCenter Pro 1100-04
provides diferent volume
coniguration types. Click a
volume and the choices are
alight.
ðreate Click this button to create a new volume.
ñòóòôe Click this button to delete a volume.
õötend/ Click to add a hard drive(s) to extend a volume, or
Spare
÷igrate
set a spare for a volume
Click to change the RAID level of a volume.
õöøùúû Click to enlarge a volume by replacing one of the
üúóýþÿ
existing hard drive with a larger capacity hard drive.
Click to unlock an encrypted volume
õúþyption Click to conigure the encryption
uto Rebuild
‹
settings of the volume.
Click to enable or disable the auto-rebuild function.
D-Link ShareCenter Pro 1100-04 User Manual
127
Section 3 - Coniguration
Software - Disk Management - Creat a Volume
tep 4:
Create to create a
new volume. The following
choices are provided.
tandalone
™
AID 0
AID 1
AID 5
AID 6
rray
e
Standalone requires only one hard drive in the array.
Each hard drive is its own volume.
JBOD requires a minimum of two hard drives,
concatenates the hard drives in a linear fashion, and
creates one large volume geared towards maximum
available space.
RAID requires a minimum of two hard drives. The
data is stored in a striped fashion and geared towards
maximum available space and performance.
CAUTION: RAID 0 does not provide data redundancy.
RAID 1 requires a minimum of two hard drives and
mirrors the hard drives for data redundancy.
RAID 5 requires a minimum of three hard drives and
provides data striping with distributed parity.
RAID 6 requires a minimum of four hard
drives, and stripes data and double-parity
information across all of the member drives.
Tick the check box to select the corresponding
hard drive to be part of the volume.
Tick the check box to select the corresponding
hard drive as a spare for the volume.
Click Next to continue
D-Link ShareCenter Pro 1100-04 User Manual
128
Section 3 - Coniguration
Software - Disk Management - Create a Volume
tep 5:
vailable are:
ƒ uto-rebuild
yption
assword
onirm
Password
uto Unlock
€
ey
!
Click the radio buttons to enable or disable autorebuild setting. Only RAID 1, RAID 5 and RAID 6 can
conigure this setting.
Click the radio buttons to enable or disable
encryption settings.
When encryption is enabled, enter a password in the
ield. A minimum of 5 digits is required.
Retype the password in the ield.
Tick the check box to automatically unlock the
volume when the system starts.
Tick the check box to save the password to a USB
drive.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
129
Section 3 - Coniguration
Software - Disk Management - Create a Volume
"
tep 6:
arning message appears before starting to create
the volume.
‘ #
Click Yes to continue.
The volume is being created. The status bar displays
the percentage of completion in real time. Once the
volume is created successfully, the Volume window
appears.
D-Link ShareCenter Pro 1100-04 User Manual
130
Section 3 - Coniguration
Software - Disk Management - Extend/Spare a Volume
tep 7:
$
rray
$-./e
,
isk
$01e

olume and the Extend/Spare button to see the
following window.
%&'() * +
Tick the check box to extend the volume.
Tick the check box to select the disk to be a spare
disk.
Displays the conigured disk number.
Displays the size of the hard disk.
Note: Only JBOD, RAID 0/1/5/6 supports volume
extensions and only RAID 1/5 and 6 supports spare
disk settings.
D-Link ShareCenter Pro 1100-04 User Manual
131
Section 3 - Coniguration
Software - Disk Management - Migrate a Volume
2
tep 7:
olume and the Migrate button to see the following
window.
34567 8 9
The windows allows you to change the RAID level of the
volume. Choose a RAID level and select the hard disks to
be used in the migration.
The wizard allows you to change the volume RAID level.
Choose a RAID level and select the hard disks to be used in
the migration.
To migrate a volume to another RAID level, the ShareCenter
Pro requires a volume’s disk array and one or more unused
disks to do the migration. The ShareCenter Pro software will
extend the volume capacity after the migration is complete.
Migration can only take place in the following instances:
Standalone to JBOD
Standalone to RAID 0/1/5/6
RAID 1 to JBOD
RAID 1 to RAID 0/5, and 6
Click OK to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
Click OK to save the
changes
132
Section 3 - Coniguration
Software - Disk Management - Expand a Volume
:
tep 8: 1. To expand a volume you need several larger capacity hard
drives.
2. Replace all the disks of this volume with larger disks, one
at a time.
3. Once you have replaced each disk, it takes a while for the
volume to recover.
4. Once the disks of the volume is replaced, ShareCenter Pro
extends the volume capacity.
ONLY RAID 1, 5 and RAID 6 supports volume expansion.
;<=>? @AB
Expand button to see the following window.
Click Yes, to continue.
Follow the instruction in the State column to expand the
Volume.
D-Link ShareCenter Pro 1100-04 User Manual
133
Section 3 - Coniguration
Disk Management - Change the Encryption Settings
tep 9:
C
DEFGH IJK
Encryption button to see the following window.
The Encryption window appears and there are four tabs
in the window. This window displays the settings in the
Change tab.
Lhange
Password
Muto Unlock
ey
NCO P
Tick the check box and enter the new password
in New Password and Conirm Password ields.
Tick the check box to automatically unlock
the volume when the system starts.
Tick the check box to save the password to a USB
drive.
Click OK to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
134
Section 3 - Coniguration
Disk Management - Change the Encryption Settings
tep 10: Rhis window displays the setting in the Save tab.
Q
Click Save to save the password to local.
tep 11: Rhis window displays the setting in the Load tab.
Q
Soad
password
from local
Click the Browse button to locate the path of the
password that is saved to the local computer.
Click the Load button to get the password from local to
unlock this volume.
D-Link ShareCenter Pro 1100-04 User Manual
135
Section 3 - Coniguration
Disk Management - Change the Encryption Settings
T
tep 10: Uhis window displays the setting in the Mail tab.
Click Mail to send the password to the administrator.
Click Mail
D-Link ShareCenter Pro 1100-04 User Manual
136
Section 3 - Coniguration
iSCSI Target
Your ShareCenter NAS supports multiple iSCSI targets and logical unit numbers (LUN) for storage expansion and backup
destination of servers. Before applying an iSCSI LUN, make sure at least one iSCSI LUN has been created on the NAS. iSCSI is
a Client-Server based protocol, except that the client process requesting data is called an “initiator” and the server process
serving the data is called a “target”. In an iSCSI implementation, the storage that is ofered by the target appears as local disk to
the initiator. The client can make block-based operations on that storage. Since this involves formatting the disk, partitioning,
creating a ile system on the disk, no more than one initiator can have read/write access to the speciic iSCSI device at a time.
However, it is possible that you can mount a iSCSI device as read-only on multiple initiators.
D-Link ShareCenter Pro 1100-04 User Manual
137
Section 3 - Coniguration
Things to know before we start
Between your computer and your storage device lies an initiator. Its called this because it initiates a connection to the device
called a target. Do not connect 2 diferent clients to the same iSCSI target at the same time. This will lead to data loss and
system crash.
Create an iSCSI Target using the iSCSI Manager
Login to your ShareCenter Pro 1100-04 as an administrator. Follow the instructions on the next page.
D-Link ShareCenter Pro 1100-04 User Manual
138
Section 3 - Coniguration
iSCSI Target - iSCSI Manager
The iSCSI Target should not be confused with iSCSI which is a protocol, iSCSI Target is a storage server instance. iSCSI is a
dedicated network connected hard disk storage device, like the DNS-1100-04. The 1100-04 provides distinct iSCSI targets for
numerous clients.
tep 1: Click Disk Management on
the left pane.
V
D-Link ShareCenter Pro 1100-04 User Manual
139
Section 3 - Coniguration
W
tep 2: Click iSCSI Target.
The right pane displays the iSCSI Manager.
W
tep 3: Click the Enable iSCSI Target checkbox to enable this
function.
Click Enable iSNS and enter the iSNS server IP address.
Click Apply to continue.
D-Link ShareCenter Pro 1100-04 User Manual
140
Section 3 - Coniguration
X
tep 4: The program saves
all conigurations.
D-Link ShareCenter Pro 1100-04 User Manual
141
Section 3 - Coniguration
iSCSI Target - iSCSI Targets
Y
tep 1: Click Disk Management under the main category window.
Click iSCSI Target, then the iSCSI Targets button
Click Create.
NB: In order to run this, you must enable iSCSI Target under iSCSI Manager.
D-Link ShareCenter Pro 1100-04 User Manual
142
Section 3 - Coniguration
tep 2: The Create iSCSI Target window opens.
Z
Under the iSCSI Target Settings enter a name for the iSCSI
Target. The name will be the suffix of this target’s iSCSI
Qualiied Name (IQN).
IQN is the acronym used to recognise this iSCSI Target. On the
ShareCenter Pro , it will be constructed to “iqn.2010-01.com.dlink:” + the device’s hostname + “:” + enter the name here.
Check the No or Yes radio button to disable or activate CHAP
services
Enter a name and password for CHAP services.
D-Link ShareCenter Pro 1100-04 User Manual
143
Section 3 - Coniguration
Note: The iSCSI Target name can contain numbers, letters of
the alphabet and some symbol like dash ‘-’ , colon ‘:’ and dot ‘.’.
Note: The CHAP name must be between 1 to 8 characters.
The CHAP password must be between 12 to 16 characters.
Both of them can accepts English letters, numbers, and
underscore ‘_’ .
Note: Both CHAP name and password can accepts English letters, numbers, and underscore ‘_’
D-Link ShareCenter Pro 1100-04 User Manual
144
Section 3 - Coniguration
tep 3: Enter the appropriate ields.
[
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
145
Section 3 - Coniguration
\
tep 4: Select None, if you do not wish to create LUN Mapping here
Click Apply.
Map the LUNs to this iSCSI target. You can specify the iSCSI LUN to map, or just create an iSCSI
Target.
NB: iSCSI Target must map one iSCSI LUN at least.
1. None: no map LUN to this target. You can map it later.
2. Create a New LUN: create a new LUN and map it to this iSCSI target.
3. Map Existing LUNs: map existing LUNs to this target.
D-Link ShareCenter Pro 1100-04 User Manual
146
Section 3 - Coniguration
tep 5: The newly created iSCSI Target appears in the iSCSI Target table.
]
The connection status will show in the “Status” column.
D-Link ShareCenter Pro 1100-04 User Manual
147
Section 3 - Coniguration
iSCSI Target - Editing iSCSI Targets
Follow these instructions to edit an iSCSI Target.
tep 1: Under iSCSI Targets, click the iSCSI Target entry you
wish to edit.
^
Click Edit.
D-Link ShareCenter Pro 1100-04 User Manual
148
Section 3 - Coniguration
_
tep 2: The Edit iSCSI Target window appears. Editing the
iSCSI Target Settings is limited to the CHAP settings.
Choose to enable or disable CHAP settings or
change the CHAP name and password settings.
_
tep 3: The next window asks you to edit the iSCSI LUN
Mapping.
You can re-map any existing LUN to this iSCSI target.
If this window doesn’t show any data, go to iSCSI
LUNs to create a new one.
D-Link ShareCenter Pro 1100-04 User Manual
149
Section 3 - Coniguration
tep 4: The iSCSI Targets window returns to the table.
`
D-Link ShareCenter Pro 1100-04 User Manual
150
Section 3 - Coniguration
iSCSI Target - Deleting iSCSI Targets
Follow these instructions to delete an iSCSI Target.
tep 1: Select the iSCSI Target
a
D-Link ShareCenter Pro 1100-04 User Manual
151
Section 3 - Coniguration
b
tep 2: The Warning message indicates that the iSCSI
Target will be deleted.
b
tep 3: The items in the iSCSI Targets table no longer exists.
D-Link ShareCenter Pro 1100-04 User Manual
152
Section 3 - Coniguration
iSCSI Target - Details of an iSCSI Targets
Follow these instructions to view details of an iSCSI Target.
c
tep 1: Select the iSCSI Target.
c
tep 2: Click the Details button to show
all details on the iSCSI Target.
D-Link ShareCenter Pro 1100-04 User Manual
153
Section 3 - Coniguration
iSCSI Target - iSCSI LUN
Introduction:
In an iSCSI environment, LUNs are essentially numbered disk drives. An initiator negotiates with a target to establish connectivity
to a LUN; the result is an iSCSI connection that emulates a connection to a SCSI hard disk. The LUN can be created using the
following two methods.
Thin provisioning:
The space is allocated only when needed. Advantages of Thin Provisioning on the ShareCenter Pro. With thin provisioning, you
can lexibly allocate the disk space (on iSCSI LUN) to the server applications to expand the storage capacity anytime regardless
of their current storage size. The adding of the storage space on the servers can be easily done on diferent operation systems
by the iSCSI initiator. Thin provisioning allows eicient storage management since the system administrator has to monitor
only the storage capacity of one single server (ShareCenter Pro) rather than extra hard drives or tapes on other sub-storage
systems. Over-allocation is allowed since the storage capacity of the NAS can be expanded.
Pre-Allocate:
The space will be allocated now. If you create a 50 GB LUN, then 50 GB will be immediately reserved for that LUN. (Note that
the creation will also take more time because of that process).
D-Link ShareCenter Pro 1100-04 User Manual
154
Section 3 - Coniguration
tep 1: Click Disk Management, iSCSI Target
d
Click the iSCSI LUN button to see the LUN coniguration.
Click the Create button to start to create an iSCSI LUN.
tep 2: Enter the basic iSCSI LUN settings
d
Name: The LUN name, you can use English letters,
numbers and some symbols like dash ‘-’ , colon ‘:’ and dot ‘.’.
Pre-allocate: Select “ Yes” to allocate volume space as the
iSCSI LUN needs; Selec t “No” to do Thin Provisioning. This
has been introduced in a previous section.
Volume: This is the Volume where the iSCSI LUN will be
stored.
Size: The size of the iSCSI LUN is in Gigabytes. If you
choose Pre-allocate as “Yes”, you can enter a size from 1 to
the maximum free size of the volume. Otherwise, you can
enter a size from 1 to the volume size. The upper bound
of the possible maximum LUN size is 2043 GB.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
155
Section 3 - Coniguration
e
tep 3: Specify an iSCSI Target to map from the iSCSI LUN you
just created.
None: no iSCSI Target will be mapped to this LUN.
Create a New Target: Create a new iSCSI Target in the
next step, and this LUN will be mapped to it.
Map Existing Target: This maps this LUN to an iSCSI Target
that has been created before.
e
tep 4: Enter the basic Target settings.
In the Name ield, enter the suix of the Target’s IQN.
Under Enable CHAP, select Yes, if you wish to have
authentication to login to the Target. Click No, if you do
not want authentication.
In the Name ield, enter the CHAP name.
In the Password ield, enter the CHAP password.
D-Link ShareCenter Pro 1100-04 User Manual
156
Section 3 - Coniguration
tep 5: The new iSCSI LUN shows up in the iSCSI LUN table.
f
D-Link ShareCenter Pro 1100-04 User Manual
157
Section 3 - Coniguration
Edit an iSCSI LUN
tep 1: Select an iSCSI LUN.
g
Click the edit button
Change the LUN size if the LUN is in thin-provisioning
settings
tep 2: Change the LUN Mapping settings here.
g
Click Apply to save settings.
D-Link ShareCenter Pro 1100-04 User Manual
158
Section 3 - Coniguration
View details of an iSCSI LUN
h
tep 1: Select an iSCSI LUN.
Click the Details button
The Details window shows the basic settings of an iSCSI
LUN and its ACL settings in the ACL table.
D-Link ShareCenter Pro 1100-04 User Manual
159
Section 3 - Coniguration
iSCSI Target - LUN ACL
LUN ACL(LUN Access Control List) deines the access permission for the initiators to the LUNs. When you need to create an
access control rule for an initiator, you need to create a new LUN ACL for it to operate. The Default Policy will be applied if the
initators are not on the list. The Default Policy is read/write in iSCSI LUN. You also can edit the Default Policy to Read Only or
Deny.
tep 1: The Default Policy will always be irst ACL on the LUN
ACL table when the iSCSI Target service is enabled.
i
Click the Create button to create a new LUN ACL for the
initiator.
D-Link ShareCenter Pro 1100-04 User Manual
160
Section 3 - Coniguration
j
tep 2: Create the iSCSI LUN ACL.
Enter the policy name and the initiator IQN
Change the LUNs’ access rights for this initiator to Read
Only, Read/Write, or Deny.
Read Only: The initiator will grant Read access rights to
the LUN.
Read/Write: The initiator will grant Read and Write access
rights to the LUN.
Deny: The initiator will not see the LUN.
Click Apply to continue.
D-Link ShareCenter Pro 1100-04 User Manual
161
Section 3 - Coniguration
k
tep 3: A warning message appears asking you to reconnect to
the initiator.
Click OK to continue.
k
tep 4: The created LUN ACL will appear here.
D-Link ShareCenter Pro 1100-04 User Manual
162
Section 3 - Coniguration
Editing the LUN ACL
You can edit the LUN ACL at your convenience.
Caution: Disconnect the iSCSI initiator from the ShareCenter Pro before editing the LUN ACL. Failure to do so can cause system
problems.
Follow these instructions to edit the LUN ACL.
l
tep 1: Select the LUN ACL you want to modify.
D-Link ShareCenter Pro 1100-04 User Manual
163
Section 3 - Coniguration
tep 2: Select the LUN ACL entry and click the Edit button.
m
tep 3: Change the LUN access permissions on the initiator.
Select either Read Only, Read/Write or Deny.
m
D-Link ShareCenter Pro 1100-04 User Manual
164
Section 3 - Coniguration
tep 4: Press the Apply button, and the modiied rule will be
applied.
n
tep 5: A LUN warning message appears asking that you
reconnect the initiator to apply the modiied ACL.
n
D-Link ShareCenter Pro 1100-04 User Manual
165
Section 3 - Coniguration
Virtual Volume
Click the Virtual Volume icon in the Disk Management window or the Virtual Volume link in the left window to conigure the
virtual volume. The Virtual Volume allows the ShareCenter Pro to expand its iSCSI capacity. By utilizing the built-in iSCSI initiator,
the ShareCenter Pro will be able to connect to other iSCSI targets on the network and convert them into virtual volumes.
These virtual volumes are seen as multiple single volumes on the ShareCenter Pro. Up to 8 virtual volumes can be stacked.
The ShareCenter 1100-04 acts as the storage stack master server. Virtual Volumes can be used to store and backup data, just
like a local volume.
reate
pdit
o
e
qrsrt
ormat

onnect/
Disconnect
o
Click the button to add a virtual volume.
Select a target and click the button to change the
settings.
Select a target and click the button to remove the
virtual volume from the list.
When using the virtual volume for the irst
time, the volume must be formatted before
mounting to the ShareCenter Pro.
Click Connect to link to a virtual volume. Click
Disconnect to terminate the connection.
D-Link ShareCenter Pro 1100-04 User Manual
166
Section 3 - Coniguration
Create a Virtual Volume
Click the Create button to see this window.
uv
vice IP
ort
xearch
w
argets
y
hare Folder
x
uthentication
Enter the IP address of the device you want
connected to the iSCSI Target
Enter the port for the device.
Click the button to search for the iSCSI targets on
the network.
Displays the available iSCSI targets.
Enter a name for the share folder to access.
ser Name
Click the Yes radio button to enable
the authentication function.
Enter the user name for authentication.
assword
Enter the password for authentication
z
{
w
Click Apply to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
167
Section 3 - Coniguration
Disk Diagnostic
Click the Disk Diagnostic icon in the Disk Management window or the Disk Diagnostic link in the left window to conigure the
Disk Diagnostic. This window is used to run a SMART (Self-Monitoring Analysis, and Reporting Technology) or Scan test. The
hard drive is grayed out if it does not support SMART.
ž
uick test
|}
~
tended
test
chedule
top
~
~
can
ormat

Click to run a quick SMART test. The test checks the
electrical, mechanical, and read performance of the
hard drive.
Click to run an extended SMART test. This takes
longer time, but checks more thoroughly and
complete than the quick test.
Click to conigure a scheduled test for the selected
hard drive.
Click to stop a test
Click to scan if there are any errors or there
is any corruption for the ile system.
Click to format a volume. All data on
the volume will be deleted.
D-Link ShareCenter Pro 1100-04 User Manual
168
Section 3 - Coniguration
Schedule Disk Diagnostic
Click the Schedule button to see this window.
‚
chedule
ype
„ime
„
eekday
–
te
…†
Use the drop-down menu to select the frequency
of the self-test schedule.
Click the radio buttons to select the type of the test.
Use the drop-down menu to select hour and minute
of the day.
Use the drop-down menu to select which day of
the week.
Use the drop-down menu to select a date.
Click OK to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
169
Section 3 - Coniguration
Scan a Volume
Click the Scan button to see this window.
Select a volume and click Scan to start to check the ile
system.
D-Link ShareCenter Pro 1100-04 User Manual
170
Section 3 - Coniguration
Format a Volume
Click the Format button to see this window.
Select a volume and click Format to format the volume.
A warning message appears to double confirm if the
formatting will proceed. Click Yes to proceed.
D-Link ShareCenter Pro 1100-04 User Manual
171
Section 3 - Coniguration
Disk Management - Scheduling a Disk Diagnostics
Schedule button to
tee this window.
Ž’“” •—˜
‡
chedule
ype
ˆime
ˆ
eekday
‰
ŠŒ
te
Use the drop-down menu to select the frequency
of the self-test schedule.
Click the radio buttons to select the type of the test.
Use the drop-down menu to select hour and minute
of the day.
Use the drop-down menu to select which day of
the week.
Use the drop-down menu to select a date.
Click OK to save the settings
D-Link ShareCenter Pro 1100-04 User Manual
172
Section 3 - Coniguration
Disk Management - Scan a Volume
Scan button to see
this window.
š›œŸ ¡¢
Select a volume and click
Scan to start to check the ile
system.
D-Link ShareCenter Pro 1100-04 User Manual
173
Section 3 - Coniguration
Disk Management - Format a Volume
Format button to
see this window.
£¤¥¦§ ¨©ª
Select a volume and click
Format to format the
volume.
A warning message appears
to double conirm if the
formatting will proceed. Click
Yes to proceed.
D-Link ShareCenter Pro 1100-04 User Manual
174
Section 3 - Coniguration
Account Management
This folder contains the Admin Password, Users, Groups, Share Folders, and ISO Mount. Click the folder to see the subcategories.
D-Link ShareCenter Pro 1100-04 User Manual
175
Section 3 - Coniguration
Admin Password
Click the Admin Password icon in the Account Management window or the Admin Password link in the left window to
conigure the Admin Password. This window is used to change the administrator’s password.
ser Name
¬assword
­®w
Password
¯onirm
Password
«
Displays administrator’s user name.
Enter the original password.
Enter a new password.
Retype the new password.
Click Apply to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
176
Section 3 - Coniguration
Users
Click the Users icon in the Account Management window or the Users link in the left window to create, edit or delete users.
This window also can assign users to various groups.
reate
±dit
mport Users
Click the button to create a new user.
Select a user and click the button to conigure the
user’s information.
Select a user and click the button to remove the user
from the list.
Click the button to import a ile with a list of users.
reate Batch
Click the button to create multiple users at one time.
earch
Enter the search keyword and click to search for
the user. Click to clear the search ield and all users’
information appears.
°
e
²³´³µ
¶
°
·
D-Link ShareCenter Pro 1100-04 User Manual
177
Section 3 - Coniguration
Create a User
Click the Create button to see the welcome window.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
178
Section 3 - Coniguration
ser Name
¹assword
ºonirm
Password
»et Quota
¸
Enter the name of a user.
Enter the password of the user.
Retype the password.
Tick the Set Quota check box to limit the storage
capacity in megabyte for the user. The value of 0
means an unlimited quota size.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
179
Section 3 - Coniguration
This window is used to add the user to a group. If there is
no entry in the list, you can go to Account Management >
Groups to create a group.
¼
earch
dd
½
age
¾
¿
efresh
Enter the search keyword and click to search for
the group. Click to clear the search ield and all of
the group’s information appears.
Tick the corresponding check box to add the user
to the group.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or
Last page ( ) to search for the group.
Click
to update the group list.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
180
Section 3 - Coniguration
This window is used to assign access rights to the user for the
corresponding share folder(s). If there are no entries in the
list, you can go to Account Management > Share Folders
to create share folders.
À
earch
ead Only
Áead/Write
Á
y
ÂÃÄ
age
Å
Á
efresh
Enter the search keyword and click to search for
to clear the search ield and all
the folder. Click
folders appear.
Tick the check box for read only access right.
Tick the check box for both read
and write access rights.
Tick the check box for no access right.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or
Last page ( ) to search for the group.
Click
to update the folder list.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
181
Section 3 - Coniguration
This window displays a summary of the configured
information.
Click Previous to modify the settings.
Click Apply to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
182
Section 3 - Coniguration
Import Users
Click the Import Users button to see the welcome window.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
183
Section 3 - Coniguration
This window allows you to import a user list ile.
wnload
ÆÇ
verwrite
duplicate
accounts
Éser List File
È
Click this button to see the example for listing
the users in the ile.
Tick the check box to replace duplicate accounts.
Click the Browse button to locate the ile.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
184
Section 3 - Coniguration
This window displays all the users in the ile. If there are any
error warnings in the State iled, the user will not be able to
go to the next window.
Click Next to continue.
The window displays the inal results of importing users to
the ShareCenter 1100-04.
Click Apply to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
185
Section 3 - Coniguration
Create Batch Users
Click the Create Batch button to see the welcome window.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
186
Section 3 - Coniguration
This window allows you to create multiple users.
ser Name Preix
Ëtart Number
Ìreate Number
Ê
assword
Ìonirm
Password
Î verwrite
duplicate
Accounts
Ëet Quota
Í
Enter the preix of the users
Enter the start number of the users.
Enter the total number of the users.
Enter the password of the users
Retype the password
Tick the check box to replace duplicate accounts.
Tick the Set Quota check box to limit the storage
capacity (in megabyte) for the user. The value of
0 means an unlimited quota size.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
187
Section 3 - Coniguration
This window is used to add the users to groups. If there is
no entry in the list, you can go to Account Management >
Groups to create groups.
Ï
earch
dd
Ð
age
Ñ
Ò
efresh
Enter the search keyword and click to search for
the group. Click to clear the search ield and all of
the group’s information appears.
Tick the corresponding check box to add the users
to the groups.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or
Last page ( ) to search for the group.
Click
to update the group list.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
188
Section 3 - Coniguration
This window is used to assign access rights to the users for
the corresponding share folder(s) to the share folders. If there
is no entry in the list, you can go to Account Management
> Share Folders to create share folders.
Ó
earch
ead Only
Ôead/Write
Ô
y
ÕÖ×
age
Ø
Ô
efresh
Enter the search keyword and click to search for
the folder. Click
to clear the search ield and all
folders appear.
Tick the check box for read only access right.
Tick the check box for both read
and write access rights.
Tick the check box for no access right.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or
Last page ( ) to search for the group.
Click
to update the folder list.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
189
Section 3 - Coniguration
This window displays a summary of the configured
information.
Click Previous to modify the settings.
Click Apply to save the settings. Depending on the amount
of users, the procedure may take a few hours.
D-Link ShareCenter Pro 1100-04 User Manual
190
Section 3 - Coniguration
Groups
Click the Groups icon in the Account Management window or the Groups link in the left window to create, edit or delete a
group.
reate
Údit
Ù
e
ÛÜÝÜÞ
ß
earch
Click the button to create a new group.
Select a group and click the button to conigure the
group’s information.
Select a group and click the button to remove the
group from the list.
Enter the search keyword and click to search for
the group. Click
to clear the search ield and all
groups’ information appears.
D-Link ShareCenter Pro 1100-04 User Manual
191
Section 3 - Coniguration
Create a Group
Click the Create button to see the welcome window.
à
roup Name
Enter a name of the group
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
192
Section 3 - Coniguration
This window is used to add the users to the group. If there is
no entry in the list, you can go to Account Management >
Users to create users.
á
earch
dd
â
age
ã
ä
efresh
Enter the search keyword and click to search for
the user. Click to clear the search ield and all users’
information appears.
Tick the corresponding check box to add the user
to the group.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or
Last page ( ) to search for the group.
Click
to update the group list.
Click Apply to save the settings.
D-Link ShareCenter Pro 1100-04 User Manual
193
Section 3 - Coniguration
Shared Folders
Shared Folders creates folders users can share over the network. These folders can be created, edited or deleted.
tep 1: Log into the system.
å
Click Create Shared Folder.
D-Link ShareCenter Pro 1100-04 User Manual
194
Section 3 - Coniguration
tep 2: The “Create Share Folder” window pops up. Here you can:
æ
• Create a Shared Folder
• Select a volume path where that folder will go
• Set share folder options and size
• Set other services like: CIFS,AFP, FTP, NFS, Web, File Manager, and WebDAV
• Set shared folder access rights
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
195
Section 3 - Coniguration
tep 3: Under Volume Path, select the path by clicking once on
the open ield. A drop down menu appears of the drives
on your NAS.
ç
Click Create to make a new folder.
D-Link ShareCenter Pro 1100-04 User Manual
196
Section 3 - Coniguration
è
tep 4: Enter a name for your new folder and click OK.
D-Link ShareCenter Pro 1100-04 User Manual
197
Section 3 - Coniguration
tep 5: Once you have entered the volume path, select the Share
Folder Option
é
Select to enable or disable the Map Archive, or Recycle Bin
D-Link ShareCenter Pro 1100-04 User Manual
198
Section 3 - Coniguration
ê
tep 6: Select to Enable the CIFS Services, Map Archive and Recycle Bin
Select the Set Quota checkbox.
Enter a Quota. The Quota is the number of MB you wish to designate the Shared Folder.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
199
Section 3 - Coniguration
tep 7: Select the Service you wish to incorporate onto this share folder.
ë
Choose from CFS, AFP, FTP, NFS, Web File Manager, or WebDAV.
Click Enable to authenticate it or Disable to stop the service.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
200
Section 3 - Coniguration
ì
tep 8: Select who you would like to access this Shared Folder.
Select All Users to give all users access to the Shared Folder
Select Speciic User to choose a user from your list or enter details of a user.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
201
Section 3 - Coniguration
tep 9: Select the Access Rights of the Shared Folder.
í
Select either Read Only, Read/Write, or Deny access.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
202
Section 3 - Coniguration
tep 10: The inal screen shows a summary of the coniguration
options just carried out. Read through the settings you
have just made.
î
Click Apply to inish the Shared Folder coniguration
settings.
D-Link ShareCenter Pro 1100-04 User Manual
203
Section 3 - Coniguration
tep 11: ShareCenter 1100-04 starts to save your settings.
ï
D-Link ShareCenter Pro 1100-04 User Manual
204
Section 3 - Coniguration
ð
tep 12: ShareCenter 1100-04 returns you to Accounts Management, Share Folders.
The table displays the Shared Folder created with size, status, and management functions.
D-Link ShareCenter Pro 1100-04 User Manual
205
Section 3 - Coniguration
Shared Folders - Editing a Shared Folder
Edit a Shared Folder within ShareCenter 1100-04.
ñ
tep 1: Select the Shared Folder you wish edit.
Click Edit.
D-Link ShareCenter Pro 1100-04 User Manual
206
Section 3 - Coniguration
ò
tep 2: The Volume is selected. Edit the Share Folder Options
(services) and Quota accordingly.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
207
Section 3 - Coniguration
tep 3: Edit the Services manually according to your needs.
ó
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
208
Section 3 - Coniguration
ô
tep 4: Edit the Access Rights in the Shared Folder for all users
or speciic users.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
209
Section 3 - Coniguration
tep 5: Now select the Permissions. The permissions can be for a local user or a local group.
õ
Select the user and select the Permission for the user
Click Apply to continue.
D-Link ShareCenter Pro 1100-04 User Manual
210
Section 3 - Coniguration
ö
tep 6: ShareCenter 1100-04 saves your configuration and
returns you to the Share Folder Table.
D-Link ShareCenter Pro 1100-04 User Manual
211
Section 3 - Coniguration
Shared Folders - Management
Manage the Shared Folder from a few icons on the table
tep 1: Click the S button under Management to provide details
on the Share Path.
÷
Click OK to exit.
D-Link ShareCenter Pro 1100-04 User Manual
212
Section 3 - Coniguration
tep 2: Click the P button to change the Access Rights.
ø
Select between All Users or Speciic Users.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
213
Section 3 - Coniguration
tep 3: Select the Access Rights for the volume.
ù
Read Only, Read/Write, or Deny.
Click Apply to complete the changes.
D-Link ShareCenter Pro 1100-04 User Manual
214
Section 3 - Coniguration
tep 4: Click the C button to change CIFS services.
ú
Select between Enable (activate) or Disable (deactivate).
Click Apply to continue.
Clicking Disable changes the color of the letter to
indicate that the service has been deactivated.
D-Link ShareCenter Pro 1100-04 User Manual
215
Section 3 - Coniguration
tep 5: Click the A button to change AFP services.
û
Select between Enable (activate) or Disable (deactivate).
Click Apply to continue.
Clicking Disable changes the color of the letter to indicate
that the service has been deactivated.
D-Link ShareCenter Pro 1100-04 User Manual
216
Section 3 - Coniguration
ü
tep 6: Click the F button to change FTP services.
Select between Enable (activate) or Disable (deactivate).
Click Apply to continue.
Clicking Disable changes the color of the letter to indicate
that the service has been deactivated.
D-Link ShareCenter Pro 1100-04 User Manual
217
Section 3 - Coniguration
tep 7: For NFS settings, the coniguration window allows you
to Disable NFS or Create a new rule.
ý
To Create a new rule click Create.
D-Link ShareCenter Pro 1100-04 User Manual
218
Section 3 - Coniguration
þ
tep 8: Under Create NFS Share, select the Permission level.
There are two choices: Read Only & Read/Write.
D-Link ShareCenter Pro 1100-04 User Manual
219
Section 3 - Coniguration
tep 9: Under Root Squash, select to activate Root Squash or
not.
ÿ
D-Link ShareCenter Pro 1100-04 User Manual
220
Section 3 - Coniguration
tep 10: Enter the Host address.
Click Apply.
D-Link ShareCenter Pro 1100-04 User Manual
221
Section 3 - Coniguration
tep 11: The NFS table now shows the changes made.
D-Link ShareCenter Pro 1100-04 User Manual
222
Section 3 - Coniguration
tep 12: To Edit
Select the volume you wish to edit, click Edit.
D-Link ShareCenter Pro 1100-04 User Manual
223
Section 3 - Coniguration
tep 13: Users can edit the Permissions of a volume in this section.
Once complete. Click Apply.
D-Link ShareCenter Pro 1100-04 User Manual
224
Section 3 - Coniguration
tep 14: Delete an NFS volume by clicking the volume.
Then, click Delete.
D-Link ShareCenter Pro 1100-04 User Manual
225
Section 3 - Coniguration
tep 15: A warning message prompts you to verify your selection.
Click Yes to delete the NFS volume.
Click No to return to your original settings.
D-Link ShareCenter Pro 1100-04 User Manual
226
Section 3 - Coniguration
tep 16: Click the M button to modify the Web File Manager.
Select between Enable (activate) or Disable (deactivate).
Click Apply to continue.
Clicking Disable changes the color of the letter to indicate
that the service has been deactivated.
D-Link ShareCenter Pro 1100-04 User Manual
227
Section 3 - Coniguration
tep 17: Click the W button to modify the WebDAV Services
Select between Enable (activate) or Disable (deactivate).
Click Apply to continue.
Clicking Disable changes the color of the letter to indicate
that the service has been deactivated.
D-Link ShareCenter Pro 1100-04 User Manual
228
Section 3 - Coniguration
Accounts Management - Shared Folders
Inactive Service
Active Service
D-Link ShareCenter Pro 1100-04 User Manual
229
Section 3 - Coniguration
ISO Mounts
Follow these steps to mount and save an ISO ile.
tep 1: Log into the system.
D-Link ShareCenter Pro 1100-04 User Manual
230
Section 3 - Coniguration
tep 2: Click Accounts Management
Click ISO Mount.
D-Link ShareCenter Pro 1100-04 User Manual
231
Section 3 - Coniguration
tep 3: Click Create, the Create ISO Mount window appears.
Read the instructions and click Next.
D-Link ShareCenter Pro 1100-04 User Manual
232
Section 3 - Coniguration
tep 4: Click the empty ield to browse to the ISO File Path.
The ISO File must be located on the NAS to authenticate
this procedure.
The ISO ile cannot be on a volume. Click the volume to
extend your search.
D-Link ShareCenter Pro 1100-04 User Manual
233
Section 3 - Coniguration
tep 5: Click Next to continue
D-Link ShareCenter Pro 1100-04 User Manual
234
Section 3 - Coniguration
tep 6: Select the Service by using one of the radio buttons
The choices include: CIFS, AFP, FTP, NFS, Web File
Manager, and WebDAV.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
235
Section 3 - Coniguration
tep 7: Under Access Rights specify the user - All Users or
Speciic Users.
Click Next to continue
tep 8: Select which Access Rights you want to assign a user.
Choose either Read Only or Deny.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
236
Section 3 - Coniguration
tep 9: The inal step is a summary. The summary displays the Path, Allowed Services, and Access Rights.
Click Apply to accept the coniguration changes or click Cancel.
D-Link ShareCenter Pro 1100-04 User Manual
237
Section 3 - Coniguration
ISO Mounts - Editing an ISO Mount
Follow these steps to edit an ISO ile.
tep 1: Once the coniguration is saved and you need to edit
your settings once again, click Edit.
D-Link ShareCenter Pro 1100-04 User Manual
238
Section 3 - Coniguration
tep 2: Select the Services you want.
Click Enable to activate the services.
Click Disable to deactivate the services.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
239
Section 3 - Coniguration
tep 3: Select the User you wish to assign or edit.
Click Next.
tep 4: Selecting a Speciic User.
Under Permissions, select the speciic user, check the
permission you want to set for this user.
Click Apply to continue.
D-Link ShareCenter Pro 1100-04 User Manual
240
Section 3 - Coniguration
tep 5: Once you have clicked Apply, the screen reverts back to the ISO Mount table.
D-Link ShareCenter Pro 1100-04 User Manual
241
Section 3 - Coniguration
ISO Mounts - Deleting an ISO Mount
Follow these steps to delete an ISO mount setting. Please note: The ISO ile will not be deleted.
tep 1: Select the ISO Mount you wish to delete
Click the Delete button.
D-Link ShareCenter Pro 1100-04 User Manual
242
Section 3 - Coniguration
tep 2: A warning message appears verifying if you want to
delete the shared folder.
Click Yes to conirm the delete instruction
Click No to exit this instruction
D-Link ShareCenter Pro 1100-04 User Manual
243
Section 3 - Coniguration
tep 3: The folder is deleted and the ISO Mount directory is empty.
D-Link ShareCenter Pro 1100-04 User Manual
244
Section 3 - Coniguration
Chapter 12 - Software - System Management
The D-Link ShareCenter Pro 1100-04 allows you to manage key system functions of your NAS. Let’s take a look.
D-Link ShareCenter Pro 1100-04 User Manual
245
Section 3 - Coniguration
Software - System Management - Network Settings
tep 1: ƒ our browser and click System Management.
D-Link ShareCenter Pro 1100-04 User Manual
246
Section 3 - Coniguration
Software - System Management - Network Settings
tep 2: ! "#$ Network icon
Click the Network icon
D-Link ShareCenter Pro 1100-04 User Manual
247
Section 3 - Coniguration
System Management - Network Settings - LAN 1
%tep 3: &he System Management,
Network window previews
all the network settings.
The main set of network
functions appear at the top
of the window. Below are
their properties.
'() (lient Click the radio button to obtain the IP address from
a DHCP server.
%tatic IP Click the radio button to assign a static IP address to
the ShareCenter Pro.
*) +ddress Enter a static IP address.
%,-./0 1ask
™,2-3
Frame
“ateway
„4AN
Enter the subnet mask for the IP address.
Use the drop-down menu to select the larger
frame size than standard Ethernet frame size.
Enter the gateway IP address
for the ShareCenter Pro.
Enable or disable the VLAN.
„4AN ID
Enter a VLAN ID when VLAN is enabled.
)ort
Bonding
5ption
Enable or disable port bonding which
is also known as port trunking.
Use the drop-down menu to select the
port bonding method. Available methods
are Round Robin, Active Backup, XOR,
Broadcast, 802.3ad, Adaptvie Transmit Load
Balancing, and Adaptive Load Balancing.
D-Link ShareCenter Pro 1100-04 User Manual
Click Apply to save the
changes
248
Section 3 - Coniguration
System Management - Network Settings - LAN 2
6tep 4: 789:; LAN 2 button to
preview settings for the
second LAN installed on the
1100-04.
<=>? >lient
6tatic IP
@? Address
6BCDEF Gask
HBICJ
Frame
Kateway
LMAN
LMAN ID
Click the radio button to obtain the IP address from
a DHCP server.
Click the radio button to assign a static IP address to
the ShareCenter Pro.
Enter a static IP address.
Enter the subnet mask for the IP address.
Use the drop-down menu to select the larger
frame size than standard Ethernet frame size.
Enter the gateway IP address
for the ShareCenter Pro.
Enable or disable the VLAN.
Enter a VLAN ID when VLAN is enabled.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
249
Section 3 - Coniguration
System Management - Network Settings - Global Settings
Ntep 5: OPQRS Global Settings to
provide an network identity
for the ShareCenter Pro.
TUV WXYZ
[rimary DNS
Necondary
DNS
\ateway
Enter the name of the ShareCenter Pro.
Enter the main DNS address for the ShareCenter Pro.
Enter the secondary DNS address for the ShareCenter
Pro.
Use the drop-down menu to
select the LAN interface.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
250
Section 3 - Coniguration
System Management - Network Settings - Route
]tep 6: ^_`ab Route to view the
Route pane.
create
dit
defege
hage
iefresh
Click to create a new routing path.
Select a routing path and click the button to edit the
routing path.
Select a routing path and click the button to remove
the entry from the list.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or
Last page ( ) to search for the group.
Click
to update the group list.
D-Link ShareCenter Pro 1100-04 User Manual
251
Section 3 - Coniguration
System Management - Network Settings - Route
jtep 7: klmno pqr Create button to
create a new routing path.
stuwork
Address
jvwxtu yask
yetric
Enter an IP address of the routing path.
Enter the subnet mask for the IP address.
Enter an integer cost metric for the route.
znterface
Use the drop-down menu to select the interface.
{ateway
Enter the forwarding or next hop IP address.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
252
Section 3 - Coniguration
System Management - Time and Date Settings
|tep 8: }~€‚ …†‡ Time and Date icon
to conigure these settings.
Click the Time
and Date icon
D-Link ShareCenter Pro 1100-04 User Manual
253
Section 3 - Coniguration
System Management - Time and Date Settings
ˆtep 9: ‰Š‹Œ Ž‘’ Time and Date icon
to conigure these settings.
”urrent Time
•ime Zone
ˆet from
Computer
ˆet Manually
ˆet from
NTP Server
Displays the current time of the ShareCenter Pro.
Use the drop-down menu to select the time zone
of your area.
Click the radio button to synchronize the ShareCenter
Pro’s time with your computer.
Click the radio button to set the time and date
manually.
Click the radio button and select a NTP server to
synchronize the ShareCenter Pro’s time with the
NTP server.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
254
Section 3 - Coniguration
System Management - System Settings
–tep 10: —˜š›œ žŸ System Settings icon
Click the System
Settings icon
D-Link ShareCenter Pro 1100-04 User Manual
255
Section 3 - Coniguration
System Management - System Settings
tep 11: ¡he System Settings
window pane provides
coniguration options for:
ave
Coniguration
¢oad
Coniguration
£¤¥¦§¨©
Coniguration
ªeb Timeout
ystem Overheat
Temperature
Click the Save button to save the current
settings to the selected location.
Click the Browse button to locate the path for
the coniguration ile and click Load to load
the ile.
Click Restore to reset the ShareCenter Pro back
to the factory default settings.
Enter a period of time. If the web is idle longer
than the time, it will be automatically logged
out.
Toggle between Celsius and Fahrenheit and enter
a temperature. Once the system temperature is
over the entered temperature;, the ShareCenter
Pro will automatically shut down.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
256
Section 3 - Coniguration
System Management - Power Management
«tep 12: ¬­®¯° ±²³ Power Management icon
Click the Power
Management icon
D-Link ShareCenter Pro 1100-04 User Manual
257
Section 3 - Coniguration
System Management - Power Management
´tep 13: µ¶·¸¹ Power Saving
Settings, select the
preferences that best suite
your needs.
º»¼d Drive
Hiberation
½urn Of
Hard Drive
¾¿ÀÁ
Display
Âuto Power
Recovery
½ype
Click Enable to enable the function.
Use the drop-down menu to select an idle time, after
which the hard drives will enter into hibernation
mode.
Use the drop-down menu to select an idle time, after
which the OLED will be turned of.
Click Enable to have the power restored
when encountering a power failure.
Use the drop-down menu to select a fan speed mode.
Available choices are Auto (Off/Low/High), Auto
(Low/High) and Manual (Always on High).
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
258
Section 3 - Coniguration
System Management - Schedule Settings
Ãtep 14: ÄÅÆÇÈ ÉÊË Schedule Power On/of Settings tab to see the
following window. This function will be deactivated if the
schedule is conigured at the same time as the irmware
update.
Ãchedule
Power On/Of
Ãchedule On
& Schedule
Of
Click Enable to set a schedule for automatic system
power on and of.
Use the drop-down menus to select the time of
system power on and of.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
259
Section 3 - Coniguration
System Management - Power Management - UPS
Follow these steps to conigure a UPS device to the NAS. This function provides a way for the NAS to monitor the UPS status
through the network. This device plays the role of the master and standalone if its connected with a USB cable. If it is not
connected in this way, the device will play the role as the slave. In the slave role it will monitor the UPS status through the
network.
Ìtep 1: Log-in to the NASÍ
D-Link ShareCenter Pro 1100-04 User Manual
260
Section 3 - Coniguration
Îtep 2: Click System Management
D-Link ShareCenter Pro 1100-04 User Manual
261
Section 3 - Coniguration
Ïtep 3: Click Power Management
D-Link ShareCenter Pro 1100-04 User Manual
262
Section 3 - Coniguration
Ðtep 4: Click UPS
UPS has two modes, Master and Standalone
From the drop-down list select Standalone
D-Link ShareCenter Pro 1100-04 User Manual
263
Section 3 - Coniguration
Ñtep 5: Once you have selected
Standalone mode, scroll
down to UPS Status.
The UPS Status provides
Device Information,
Manufac turer, Produc t,
Battery Charge, and Status.
Click Apply to continue
D-Link ShareCenter Pro 1100-04 User Manual
264
Section 3 - Coniguration
Òtep 6: The alternative is to select Master UPS mode.
The Master UPS mode has three slave device IP address inputs.
D-Link ShareCenter Pro 1100-04 User Manual
265
Section 3 - Coniguration
Ótep 7: Enter an IP address into the ield provided.
Click Apply to submit the changes.
D-Link ShareCenter Pro 1100-04 User Manual
266
Section 3 - Coniguration
Ôtep 8: A network UPS slave communicates with network UPS master
to receive the UPS status. To set up your NAS with UPS as
network slave mode, follow the steps below:
1.
Make sure the NAS is connected to the same physical
network as the network UPS master.
2.
Select the option “Enable Network UPS”.
3.
Enter the IP address of the network UPS master.
4.
Click “Apply” to conirm.
Note: Coniguring network UPS is not the default coniguration. Ask a systems administrator to assist you with all coniguration
operations. This feature is ideal for SOHO and medium size businesses that use more than one UPS and NAS. Make sure your
network supports network UPS alerts.
D-Link ShareCenter Pro 1100-04 User Manual
267
Section 3 - Coniguration
System Management - Email Alerts
Õtep 15: Ö×ØÙÚ ÛÜÝ Email Alerts icon.
Click the Email Alerts icon
D-Link ShareCenter Pro 1100-04 User Manual
268
Section 3 - Coniguration
System Management - Email Alerts
êtep 16: îïðñò óôõ Email Alerts icon to conigure the email alert
settings.
Þßàáâ ãlert
êëTP Server
Click the radio buttons to enable or disable the
e-mail alert function.
Use the drop-down menu to select the
login method. If the SMTP server requires
authentication, select Login. If not, select
Anonymous.
If Login is selected in Login Method, enter the
user name of the e-mail account.
If Login is selected in Login Method, enter the
password of the e-mail account.
Select SSL/TLS if the SMTP server requires
authentication.
Enter the IP address of the SMTP server.
æort Number
Enter the port number of the SMTP server.
äogin Method
åser Name
æassword
Þçèéyption
êender E-mail
ìeceiver E-mail
íest E-mail
Þvent Alert
Settings
Enter the sender’s e-mail address.
Enter the e-mail address that the e-mail alert
sends to.
Click the Test E-Mail button
to send a test e-mail.
Tick the check boxes to select the situation that
will cause the e-mail alert to be sent out.
D-Link ShareCenter Pro 1100-04 User Manual
269
Section 3 - Coniguration
System Management - Firmware Upgrade
ötep 17: ÷øùúû üýþ Firmware Upgrade icon.
Click the Firmware
Upgrade icon
D-Link ShareCenter Pro 1100-04 User Manual
270
Section 3 - Coniguration
System Management - Firmware Upgrade
ÿtep 18: Choose File, select a ile to update the irmware.
urrent
Firmware Version
irmware Date
ile Path
Displays the current irmware in the system.
Displays the date of the irmware.
Click the Browse button to locate the irmware.
You must save the irmware to the local hard
drive of your computer before upgrading the
irmware.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
271
Section 3 - Coniguration
System Management - Logs
tep 19: Logs icon
Click the Logs icon
D-Link ShareCenter Pro 1100-04 User Manual
272
Section 3 - Coniguration
System Management - Logs
tep 20: onigure the log settings based on your needs. The list includes:
ƒog Settings
Click the radio buttons to enable various situations
which will be recorded in the logs.
ystem Log: Keeps a log of your system
stats.
NFS: Enable Network File Systems to access
iles over the network.
CIFS: Provides shared access to iles.
FTP: File transfer Protocol to setup ile
transfer.
Event: To monitor your events on your NAS.
Log Settings
D-Link ShareCenter Pro 1100-04 User Manual
273
Section 3 - Coniguration
System Management - Logs
tep 21: Log Message List to
monitor the activity on your
system.
You can refresh logs, clear a
log, or save a log.
D-Link ShareCenter Pro 1100-04 User Manual
274
Section 3 - Coniguration
System Management - Syslog Server
tep 22 Log in to your NAS.
tep 23 Click System Management.
D-Link ShareCenter Pro 1100-04 User Manual
275
Section 3 - Coniguration
tep 24 Under System Management, Syslog Server, click
Enable Syslog Server.
Click Apply to continue.
D-Link ShareCenter Pro 1100-04 User Manual
276
Section 3 - Coniguration
System Management - Syslog Server Rule
Follow these steps to create a Syslog Server Role.
tep 1
Under System Management, Syslog Server, click
Syslog Server Rule.
Click Create.
D-Link ShareCenter Pro 1100-04 User Manual
277
Section 3 - Coniguration
tep 2
Under Create Syslog Server Rule, create a Rule Name
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
278
Section 3 - Coniguration
tep 3
Under Protocols and Severity, select from the
options available.
Facility:- Auth, Crons, Daemon, FTP, Kern, LPR,
Mail, News, Syslog
Severity:- Debug, Information, Notice, Warning,
Error, Alert, Critical, Emergency
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
279
Section 3 - Coniguration
tep 4
Under Log File, browse to the path where you
want to save the ile.
Type a File Name
D-Link ShareCenter Pro 1100-04 User Manual
280
Section 3 - Coniguration
!tep 5: Click Next to continue.
!tep 6: Under Log File Rotation.
Click Enable.
D-Link ShareCenter Pro 1100-04 User Manual
281
Section 3 - Coniguration
"tep 7: Enter the Number of Log Files
Click Rotate by Size. Enter the Maximum Log File Size in “MB”
Click Rotate by Frequency.
Rotation Frequency is Daily, Weekly, or Monthly
Click Apply.
D-Link ShareCenter Pro 1100-04 User Manual
282
Section 3 - Coniguration
#tep 8: The Total Number of Log Files cannot exceed “10”.
The warning message prompts you change your
coniguration.
D-Link ShareCenter Pro 1100-04 User Manual
283
Section 3 - Coniguration
$tep 9: Enter the Log File amount.
Click Apply.
$tep 10: The Rule now appears in Syslog
Server Rule table.
D-Link ShareCenter Pro 1100-04 User Manual
284
Section 3 - Coniguration
System Management - Edit a Syslog Server Rule
Follow these steps to edit a Syslog Server Rule:
%tep 1: Select the Server Rule you wish to edit
Click Edit.
D-Link ShareCenter Pro 1100-04 User Manual
285
Section 3 - Coniguration
&tep 2: The Rule Name window is irst.
However, the Rule Name cannot be edited.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
286
Section 3 - Coniguration
'tep 3: Under Protocols and Severity, select from the options available.
Select or deselect the options you want to edit
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
287
Section 3 - Coniguration
(tep 4: Edit the Log File, the path and/or
File Name.
D-Link ShareCenter Pro 1100-04 User Manual
288
Section 3 - Coniguration
)tep 5: Edit the Log File Rotation according
to your requirements.
Click Apply.
The changes take efect immediately.
D-Link ShareCenter Pro 1100-04 User Manual
289
Section 3 - Coniguration
System Management - Delete a Syslog Server Rule
Follow these steps to edit a Syslog Server Rule.
*tep 1: Select the Server Rule you wish to delete
Click Delete.
D-Link ShareCenter Pro 1100-04 User Manual
290
Section 3 - Coniguration
+tep 2: A warning message asks you to conirm your selection.
Click Yes to delete the Rule.
Click No to cancel your coniguration.
D-Link ShareCenter Pro 1100-04 User Manual
291
Section 3 - Coniguration
System Management - Enable/Disable a Syslog Server Rule
Follow these steps to toggle between enabling and disabling a Syslog Server Rule:
,tep 1: Select the Server Rule you wish to
enable or disable
Click the Enable/Disable Rule
button to toggle between the two.
The Status column will indicate
whether the device is enabled or
disabled.
D-Link ShareCenter Pro 1100-04 User Manual
292
Section 3 - Coniguration
System Management - Clearing a Syslog Server Log
Follow these steps to clear a Syslog Server Log File:
-tep 1: Select the Server Log you wish to clear.
Click Clean Log.
D-Link ShareCenter Pro 1100-04 User Manual
293
Section 3 - Coniguration
.tep 2: A warning message appears to notify you that the log will
be deleted.
Click Yes to clear the Log ile.
Click No to make no changes.
Click the Download Log button to download the log.
D-Link ShareCenter Pro 1100-04 User Manual
294
Section 3 - Coniguration
Chapter 13 - Software - Network Services
The D-Link ShareCenter Pro 1100-04 allows you to monitor and conigure Network Services. Let’s take a look.
D-Link ShareCenter Pro 1100-04 User Manual
295
Section 3 - Coniguration
Software - Network Services
/tep 1:
01234 567 Network Services
folder to the right. Click File
Sharing.
Click the File Sharing
icon
D-Link ShareCenter Pro 1100-04 User Manual
296
Section 3 - Coniguration
Software - Network Services - File Sharing
8tep 2:
9he File Sharing
coniguration window ofers
ive important protocol
options.
CIFS:
FTP:
NFS:
DFS:
Quota:
AFP:
WebDAV:
Each of these protocols can
be conigured.
Select the choices you want
to enable and click Apply.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
297
Section 3 - Coniguration
Software - Network Services - File Sharing - FTP
:tep 3: ABCDE FGH FTP tab
Control Port
;ort Range of
Passive FTP
<espond with
external IP
address for
Passive mode
=lient Language
ax
Connections
ax
Connections per
IP
=onnection Idle
Time
ˆandwidth
Restriction
‹nonymous
The default port for FTP is 21. Enter a port
number in the range of 1025 to 3688, 3690 to
49999, and 65501 to 65535.
The default port range for passive FTP is from
55536 to 55663. Click the Use the following port
range radio button and manually enter the port
range from 1025 to 65535.
Click Enable to respond with external IP address
for the passive FTP connection request.
Use the drop-down menu to select the supported
language for the FTP clients.
Use the drop-down menu to select the maximum
number of concurrent FTP connection.
Use the drop-down menu to select the maximum
number of concurrent FTP connection per IP
address.
Use the drop-down menu to select the time that
the FTP server logs out the user after this period
of idle time.
Click Enable to restrict the bandwidth of each
FTP connection. Enter the number in KB/s for
the maximum speed of upload and download.
Click Enable to allow anonymous FTP to log in.
Click Apply to save the
changes
Support
::>?@>:
Connection Only
Click Enable to only allow SSL or TLS connection
requests from the FTP clients.
D-Link ShareCenter Pro 1100-04 User Manual
298
Section 3 - Coniguration
Software - Network Services - File Sharing - CIFS
Itep 4: JKLMN OPQ CIFS tab to conigure this protocol
RSTUVWXVYZ
–orkgroup
[ctive
Directory
€ser Name
\assword
]I
–orkgroup
^ealm Name
[ Ierver
Enter the description of your device.
Click the radio button to choose the system to be
in a workgroup. Enter the name of the workgroup
in the ield.
Click the radio button to choose the system to be in
an Active Directory (AD).
Enter the AD server account name.
Enter the AD server account password.
Enter a DNS IP address to analyze the
domain name of the AD server.
Enter the name of the workgroup which should
be the same as the computers on the network.
Enter the AD server domain name.
Enter the AD server hostname.
Name
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
299
Section 3 - Coniguration
Software - Network Services - File Sharing - DFS
_tep 5: `abcd efg DFS tab to conigure this protocol
hreate
dit
ijkjle
_earch
mage
nefresh
Click to add a new DFS share.
Select a local share name and click the button to edit
the DFS share.
Select a local share name and click the button to
remove the entry from the list.
to search for
Enter the search keyword and click
the DFS share. Click
to clear the search ield and
see all the entries.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or Last
page ( ) to search for the group.
Click
to update the group list.
D-Link ShareCenter Pro 1100-04 User Manual
300
Section 3 - Coniguration
Software - Network Services - File Sharing - DFS
otep 6: pqrst uvw Create button to add a new DFS share.
xyz
{emote
share folder
|ocal share
name
Enter an IP address, a host name or a URL in the ield.
Enter a remote share folder location manually, or click
the Get Host Share Folder button to search for one.
Enter the local share name in the ield.
Click Apply to save the
changes.
D-Link ShareCenter Pro 1100-04 User Manual
301
Section 3 - Coniguration
Software - Network Services - Dynamic DNS
}tep 1:
~‚„…† ‡‰Š Dynamic DNS folder
Click the Dynamic DNS
icon
D-Link ShareCenter Pro 1100-04 User Manual
302
Section 3 - Coniguration
Software - Network Services - Dynamic DNS
Œtep 2:
Ž‘’“” •—˜ Dynamic DNS folder
™ynamic DNS
Œerver Address
š›œ žŸ ¡
¢sername or Key
£assword or Key
¤erify Password
or Key
¥imeout
Œtatus
Click the radio button to enable or disable the
dynamic DNS function.
Use the drop-down menu to select a dynamic
DNS service provider.
Enter the host name.
Enter the username or key provided by the
dynamic DNS service provider.
Enter the password or key provided by the
dynamic DNS service provider.
Re-type the password or key.
Enter a time in hours for periodic updates from
the dynamic DNS provider.
Displays the current status to the server.
Click Apply to save the
changes
D-Link ShareCenter Pro 1100-04 User Manual
303
Section 3 - Coniguration
Software - Network Services - SNMP
¦tep 1:
§¨©ª« ¬­® SNMP folder.
Click the SNMP icon
D-Link ShareCenter Pro 1100-04 User Manual
304
Section 3 - Coniguration
Software - Network Services - SNMP
¯tep 2:
°onigure the SNMP settings. SNMP is used to
monitor the conditions of the network-attached
devices.
¯±²³
¯±²³
Community
±´µ¶·¸¹tion
±´µ¶·¸¹tion IP
Enable or Disable SNMP.
Enter the name of the SNMP community.
Enable or Disable trap support.
Enter the IP address that will receive the
notiication.
Click Apply to save the
changes.
D-Link ShareCenter Pro 1100-04 User Manual
305
Section 3 - Coniguration
Software - Network Services - Network Discovery Services
ºtep 1: »¼½¾¿ ÀÁ Network
Discovery Services
folder
Click the Network
Discovery
Services icon
D-Link ShareCenter Pro 1100-04 User Manual
306
Section 3 - Coniguration
Software - Network Services - Network Discovery Services
Ãtep 2: Åhe Network Discovery Services settings are as follows:
UPnP Discovery
ÄÄTD
Click Enable to allow the ShareCenter Pro to be
discovered on a network via the UPnP discovery
protocol.
Click Enable to allow the ShareCenter Pro to be
discovered by the network map under Windows
Vista or Windows 7.
Click Apply to save the
changes.
D-Link ShareCenter Pro 1100-04 User Manual
307
Section 3 - Coniguration
Chapter 14 - Software - Applications
The D-Link ShareCenter Pro 1100-04 allows you to conigure a Web File Manager and Download Manager. Let’s take a look.
D-Link ShareCenter Pro 1100-04 User Manual
308
Section 3 - Coniguration
Software - Applications - Web File Manager
Ætep 1:
ÇÈÉÊË ÌÍÎ Web File Manager folder
Click the Web File
Manager icon
D-Link ShareCenter Pro 1100-04 User Manual
309
Section 3 - Coniguration
Software - Applications - Web File Manager
Ïtep 2:
Ðonigure the Web File Manager to start a web server
for users to upload and download iles through the
web browser.
Ïerver
ÑÒTP Port
ÏÏÓ Ôonnection
ÏÏÓ Õort
Click the radio buttons to enable or disable the
server.
Enter the port number for the function. Port 80
cannot be used as it is used for administration
purposes.
Click the radio buttons to enable or disable the
HTTPS connection.
Enter the port number for the HTTPS connection.
Click Apply to save the
changes.
D-Link ShareCenter Pro 1100-04 User Manual
310
Section 3 - Coniguration
Software - Applications - Download Manager
Ötep 3:
×ØÙÚÛ ÜÝÞ Download
Manager folder
Click the Download
Manager icon
D-Link ShareCenter Pro 1100-04 User Manual
311
Section 3 - Coniguration
Software - Applications - Download Manager
ßtep 4:
àhe Download Manager is used to schedule downloading
iles from teh FTP or HTTP sites.
áreate
âdit
ãäåäæe
çage
èefresh
Click to add a new download job.
Select an entry and click the button to edit.
Select an entry and click the button to remove the
entry from the list.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or Last
page ( ) to search for the group.
Click
to update the group list.
D-Link ShareCenter Pro 1100-04 User Manual
312
Section 3 - Coniguration
Software - Applications - Download Manager
étep 5:
êëìíî ïðñ Create button to create a downloading Job.
òównload
Type
ôogin method
õser Name
öassword
÷ype
õøô
éave To
Toggle between the FTP or HTTP download
methods.
Click the Account radio button when a password
is required for downloading files. Click the
Anonymous where there is no password required
for downloading iles.
Enter a user name for downloading.
Enter a password for downloading.
Toggle between File or Folder to download the
speciic ile or all iles in a speciic folder.
Enter the FTP, HTTP or local site address for the
scheduled download. Click the Test button to see
if the URL can be connected.
Click the ield to show the available folders. Click
the Create button to add a new folder. Double-click
a folder to select it.
Click Next
D-Link ShareCenter Pro 1100-04 User Manual
313
Section 3 - Coniguration
Software - Applications - Download Manager
ùtep6:
úo schedule a new Download job.
ûecurring
Download
ühen
ýime
üeekly
þonthly
Use the drop-down menu to have repeated
scheduled download time every day, week or
month. Select None to disable the recurring
download.
Click
to select year and date for downloading.
Use the drop-down menu to select downloading
time.
Select a day of the week for recurring download.
Select the month for recurring download.
Click Apply to save the
changes.
D-Link ShareCenter Pro 1100-04 User Manual
314
Section 3 - Coniguration
Chapter 15 - Software - Backup
The D-Link ShareCenter Pro 1100-04 allows you to conigure a Backup service for your NAS. Let’s take a look.
D-Link ShareCenter Pro 1100-04 User Manual
315
Section 3 - Coniguration
Software - Backup
ÿtep 1:
Backup folder on
the left pane
Click the Backup Folder
D-Link ShareCenter Pro 1100-04 User Manual
316
Section 3 - Coniguration
Software - Backup - Volume Snapshot
Volume Snapshot.
C l i c k t h e Vo l u m e
Snapshot icon.
D-Link ShareCenter Pro 1100-04 User Manual
317
Section 3 - Coniguration
Software - Backup - Volume Snapshot
tep 2:
reate
dit
e
ake
snapshot
how
snapshot
he Volume Snapshot is used to create, edit, or delete
a snapshot job. It also allows you to take a snapshot of a
volume. The ShareCenter Pro supports up to 10 snapshots
and each job can have a maximum of 20 snapshots.
Click to add a new snapshot job.
Select an entry and click the button to edit.
Select an entry and click the button to remove the
entry from the list.
Click the button to take a snapshot of a volume.
Click the button to show the calendar indicating on
which dates a snapshot had been taken.
D-Link ShareCenter Pro 1100-04 User Manual
318
Section 3 - Coniguration
Software - Backup - Volume Snapshot
tep 3:
Create button to
creat a Snapshot job.
older

ount
chedule
ime
!
eekday
–
"#
te
Click the ield to show the available folders. Click a
folder to see the sub-folders. Double-click a folder
to select it.
Use the drop-down menu to select the number of
snapshots for this job.
Use the drop-down menu to select manually
schedule the job, or schedule to take the snapshot
on a daily, weekly or monthly basis.
Use the drop-down menus to select hour and
minute of the day.
Use the drop-down menu to select the day of the
week.
Use the drop-down menu to select the day of the
month.
Click Apply to save the
changes.
D-Link ShareCenter Pro 1100-04 User Manual
319
Section 3 - Coniguration
Software - Backup - Volume Snapshot
tep 4:
$
alendar
-
Show Snapshot
button to see the calendar
%&'() *+,
Find the year and month of the snapshot on that
day. The date cell is highlighted when there are
snapshots on that day. Click the cell to view details
of the volume’s snapshot(s).
Click Close to go back to the
Volume Snapshot window.
Click Close.
D-Link ShareCenter Pro 1100-04 User Manual
320
Section 3 - Coniguration
Software - Backup - Volume Snapshot
tep 5:
.
/0102
e
age
3
4
efresh
fter the calendar is closed the ShareCenter Pro 1100-04
provides snapshot information.
‘
Select an entry and click the button to remove the
entry from the list.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or Last
page ( ) to search for the group.
Click
to update the group list.
Click Close to go back to the previous window.
Click Close.
D-Link ShareCenter Pro 1100-04 User Manual
321
Section 3 - Coniguration
Software - Backup - Local Backup
tep 1:
5
6789: ;<=
Local Backup icon
Click the Local Backup
icon
D-Link ShareCenter Pro 1100-04 User Manual
322
Section 3 - Coniguration
Software - Backup - Local Backup
tep 2:
>
reate
@dit
ABCBDe
?
age
E
F
efresh
ocal Backup allows iles and folders to be backed up to
local folders.
ƒ
Click to add a new backup job.
Select an entry and click the button to edit.
Select an entry and click the button to remove the
entry from the list.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or Last
page ( ) to search for the group.
Click
to update the group list.
D-Link ShareCenter Pro 1100-04 User Manual
323
Section 3 - Coniguration
Software - Backup - Local Backup
tep 3:
G
HIJKL MNO
ogin Method
P
ser Name
Qassword
Rype
€
ath
Q
G
S
ave To
ncremental
Backup
Create button to create a Local Backup Job.
Click the Account radio button when a password is
required for the procedure. Click the Anonymous
where there is no password required for the
procedure.
Enter a user name for backup.
Enter a password for backup.
Toggle between File or Folder to download the
speciic ile or all iles in a speciic folder.
Enter the path manually, or click Local to locate the
path. Click the Test button to see if the path can be
connected to.
Click the ield to show the available folders. Click
the Create button to add a new folder. Double-click
a folder to select it.
Tick the check box to enable the incremental
backup method. All backups after the first full
backup will be on an incremental basis. Only the
changes since the last backup will be backed up.
D-Link ShareCenter Pro 1100-04 User Manual
Click Next.
324
Section 3 - Coniguration
Software - Backup - Local Backup
tep 4:
T
V
ecurring
Backup
W
hen
ime
X
eekly
onthly
W
U
et the schedule for local backups by doing:
Use the drop-down menu to enable a recurring
backup. This can be done on a daily, weekly or
monthly basis. Select None to disable the recurring
backup.
to select year and date for backup.
Click
Use the drop-down menu to select the time for
backup.
Select a day of the week for recurring backup.
Select the month for recurring backup.
Click Apply to save the
changes.
D-Link ShareCenter Pro 1100-04 User Manual
325
Section 3 - Coniguration
Software - Backup - Local Backup
tep 1:
Y
Z[\]^ _`a
Remote Backup
icon.
Click the Remote
Backup icon.
D-Link ShareCenter Pro 1100-04 User Manual
326
Section 2 - Installation
Software - Backup - Remote Backup Server
tep 2:
b
Remote Backup Server tab to see this window
and the options available.
cdefg hij
emote
Backup
rassword
klmnop q
Tick the check box to enable the function.
Enter the password for backing up iles and folders
from or to the ShareCenter Pro. This is the remote
backup password. The password for the remote
NAS should be the same as the password of the
ShareCenter Pro.
Click Apply to save the settings.
Click Apply to save the
changes.
D-Link ShareCenter Pro 1100-04 User Manual
327
Section 3 - Coniguration
Software - Backup - Remote Backup Job
tep 3:
s
tuvwx yz{
reate
}dit
~‚„e
|
ˆ
ackup
}…†‡‚‰
Disable
Schedule
Šage
‹
efresh
Remote Backup Job
Click to add a new remote backup job.
Select an entry and click the button to edit.
Select an entry and click the button to remove the
entry from the list.
Click the button to back up.
Click the button to enable or disable the schedule
remote backup function.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page.
Click First Page ( ), Previous Page ( ), Next Page (
) or Last page ( ) to search for the group.
Click
to update the group list.
D-Link ShareCenter Pro 1100-04 User Manual
328
Section 3 - Coniguration
Software - Backup - Remote Backup Job
tep 4:
Œ
Œ
Ž’“”•
erver Type
Create.
Use the drop-down menu to select between D-Link
NAS Server or Rsync Server.
Click Next to continue.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
329
Section 3 - Coniguration
Software - Backup - Remote Backup Job
tep 5:
—
˜™
š›œ žŸ older Path
¡
ter the Job Name and Folder Path.
Enter the name of the remote backup job.
Click the ield to select the source ile/folder to be
backed up remotely.
Click Next to continue.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
330
Section 3 - Coniguration
Software - Backup - Remote Backup Job
tep 6:
¢
£¤
ter the Destination Settings and click Next.
emote
Server
¦assword
ª«¬­ yption
Support
®eep Existing
File
¥¦ §¨ ©
Enter the IP address of the server.
Enter the password of the destination server.
Tick the check box to enable SSH encryption.
Tick the check box to keep the existing ile with
the same name at the remote server and create
another copy for backup.
D-Link ShareCenter Pro 1100-04 User Manual
331
Section 3 - Coniguration
Software - Backup - Remote Backup Job
tep 7:
¯
°±
ter the Destination Path and click Next.
tion
Path
²³´µ¶·¸
Click the ield to select the destination path.
D-Link ShareCenter Pro 1100-04 User Manual
332
Section 3 - Coniguration
Software - Backup - Remote Backup Job
tep 8:
¹
ter the Destination Schedule details, including where
to place recurring backups.
º»
Click Apply to continue.
¼
ecurring
Backup
½
hen
ime
¾
eekly
¿onthly
½
Use the drop-down menu to enable a recurring
remote backup. This can be done on a daily, weekly
or monthly basis. Select Backup now to start the
backup.
to select year and date for backup.
Click
Use the drop-down menu to select the time for
backup.
Select a day of the week for recurring backup.
Select the month for recurring backup.
Click Apply to save the
changes.
D-Link ShareCenter Pro 1100-04 User Manual
333
Section 3 - Coniguration
Software - Backup - External Backup
tep 1:
À
ÁÂÃÄÅ ÆÇÈ
External Backup
icon
Click the Ex ternal
Backup icon
D-Link ShareCenter Pro 1100-04 User Manual
334
Section 3 - Coniguration
Software - Backup - External Backup
tep 2:
É
É
É
nsert your device into the USB slot at the back of the
NAS and select the path and USB port you want to
backup your information to.
Ê
ource
elect Path
Ë
ode
Click the USB port that is connected to an external
USB storage device.
Click the ield to show the available folders. Click the
Create button to add a new folder. Double-click a
folder to select it.
Tick the Incremental Backup check box to enable
the incremental backup method. All backups after
irst full backup will be on an incremental basis. Only
the changes since the last backup will be backed up.
D-Link ShareCenter Pro 1100-04 User Manual
335
Section 3 - Coniguration
Software - Backup - External Backup
Ì
tep 1:
ÍÎÏÐÑ ÒÓÔ
Amazon S3 icon.
Click the Amazon S3
icon.
D-Link ShareCenter Pro 1100-04 User Manual
336
Section 3 - Coniguration
Amazon S3
mazon S3 (Simple Storage Service) is an online storage web service ofered by AWS (Amazon Web Services), and it provides a simple web
services interface that can be used to store and retrieve any amount of data, at any time, from anywhere on the web. With Amazon S3 support,
you can easily upload the data from your ShareCenter Pro to Amazon S3 or download the data from Amazon S3 to your NAS.
Õ
This Amazon S3 How-To will show you how to:
y
Create your AWS Account with which you can use to access the Amazon S3 services.
y
Create a bucket on the Amazon S3 Server where you can upload or download your ShareCenter Pro data to/from.
y
Create an Amazon S3 Scheduled Backup on your ShareCenter Pro to automatically upload any ShareCenter Pro Network Share to the
Amazon S3 service.
D-Link ShareCenter Pro 1100-04 User Manual
337
Section 3 - Coniguration
Amazon S3
Follow these steps to setup Amazon S3:
tep 1: Log in. Click Backup, Amazon S3.
Ö
Click Create.
D-Link ShareCenter Pro 1100-04 User Manual
338
Section 3 - Coniguration
×
tep 2: The Create Amazon S3 Job wizard
appears providing the following
details:
Job Name Settings
Remote Settings
Server Type
Local Settings
Schedule Settings
Finish
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
339
Section 3 - Coniguration
tep 3: Enter a Job Name
Ø
Click Next to continue.
tep 4: Remote Settings
Ø
Enter the Access Key, Private Key,
Remote Path and Region supplied
my Amazon
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
340
Section 3 - Coniguration
tep 5: Select whether you want to upload
files or download files from the
dropdown list.
Ù
Select the Backup Type under the
next drop-down list.
Click Next to continue.
tep 6: Select the Local Path settings for
your backup
Ù
Click in the Local Path area. Your
NAS drive should appear.
Locate the path of your drive.
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
341
Section 3 - Coniguration
Ú
tep 7: Select the Schedule Settings.
Under Schedule Mode you can select Manual setup,
Once (once clicked the time settings appear), and
Schedule (the daily, weekly, and monthly) options
appear
You can also setup to Backup Now.
Click Enable or Disable to set these settings.
Ú
tep 8: A summary of the coniguration just completed is
displayed. This is the inal step in the wizard.
Click Apply to end the wizard or Previous to back
and make changes. Click cancel to exit and make no
changes.
D-Link ShareCenter Pro 1100-04 User Manual
342
Section 3 - Coniguration
tep 9: Once you have applied the settings and return to
the main Amazon S3 screen, the results of your
coniguration is highlighted and depending on
your coniguration is “running”
Û
Highlighting your Amazon S3 setup and clicking
the Edit button allows you to make changes to
your coniguration.
Click the Edit button to make changes. You are
returned to the Amazon S3 wizard. Make relevant
changes.
Highlighting the task you wish to delete.
A warning message will appear asking you if you
wish to delete the task.
Click Yes to delete.
Click No to return back to the previous page.
D-Link ShareCenter Pro 1100-04 User Manual
343
Section 3 - Coniguration
Chapter 18 - Software - Extension Pack
The D-Link ShareCenter Pro 1100-04 allows you to conigure extension features for your NAS. Let’s take a look.
Note: The Extension Pack only supports the Multi-Language package.
D-Link ShareCenter Pro 1100-04 User Manual
344
Section 3 - Coniguration
Extension Pack
This folder contains the Extension Pack. Click the folder to see the subcategories.
D-Link ShareCenter Pro 1100-04 User Manual
345
Section 3 - Coniguration
Extension Pack
Click the Extension Pack icon in the Extension Pack window or the Extension Pack link in the left window to conigure the
add-ons.
ile Path
Ü
dd-ons
List
Þtatus
Ý
tart/Stop
ßàáàâe
ãefresh
Þ
age
ä
Click the Browse button to locate the ile. Click Apply
to add the ile to the Add-ons list.
Displays a list of all add-on modules.
Displays if the module is currently activated (Enabled)
or deactivated (Disabled).
Activate/Deactivate the module.
Remove the add-on module from the list.
Displays number of pages. You can enter a page
number in the ield to jump to the speciic page. Click
First Page ( ), Previous Page ( ), Next Page ( ) or Last
page ( ) to search for the group.
Click
to update the group list.
D-Link ShareCenter Pro 1100-04 User Manual
346
Section 3 - Coniguration
Chapter 19 - Appendix
The D-Link ShareCenter Pro 1100-04 knowledge base is a helpful link to technological terms within this manual.
D-Link ShareCenter Pro 1100-04 User Manual
347
Section 4 - Knowledge Base
Knowledge Base
What is RAID?
RAID, short for Redundant Array of Independent Disks, is a combination of two or more disks with the aim of providing fault
tolerance and improving performance. There are several diferent levels of RAID, with each one providing a diferent method of
sharing or distributing data among the drives. The ShareCenter Pro supports JBOD, RAID 0, RAID 1, RAID 5, and Standalone.
å
AID 0
RAID 0 provides data striping, which spreads out
blocks of data over all drives, but does not provide
data redundancy.
Although performance is improved, the lack of
fault tolerance means that if one drive fails, all data
in the array will be lost.
D-Link ShareCenter Pro 1100-04 User Manual
å
AID 1
RAID 1 provides mirroring over multiple disks, with the
same read/write speed of a single disk. A RAID 1 array can
only be as large as it’s smallest member disk.
Because the data is stored on multiple disks,
RAID 1 provides fault tolerance and protection, in
addition to performance advantages.
348
Section 4 - Knowledge Base
æ
AID 5
RAID 5 provides data striping with distributed parity, which stores information that can be used to reconstruct data. A RAID 5
array will be the size of all the combined disks capacity less the capacity of one disk, e.g. If there are 4x 80GB disks in the array,
the arrays capacity will be 240GB (3x80GB).
Implementing RAID 5 on the ShareCenter Pro allows it to continue operating even if one of the disks fails.
The diagram below indicates the operation of RAID 5:
D-Link ShareCenter Pro 1100-04 User Manual
349
Section 4 - Knowledge Base
Mapping a Drive
You can use the D-Link EZ Search Utility to map drives to your computer. Insert the ShareCenter Pro CD into your CD-ROM drive.
Click EZ Search Utility.
The EZ Search Utility will load and detect any ShareCenter Pro devices that are on the local network.
D-Link ShareCenter Pro 1100-04 User Manual
350
Section 4 - Knowledge Base
If the ShareCenter Pro you are working with does not show up in the device list, click Refresh.
Highlight an available ShareCenter.
Available volumes will be displayed
under Drive Mapping. Highlight the
volume you want to map.
Select an available drive letter from the
drop-down menu and click Connect.
Once connected, your mapped drive(s) will appear in My Computer.
D-Link ShareCenter Pro 1100-04 User Manual
351
Section 4 - Knowledge Base
ouble-click the My Computer
icon on your desktop.
ç
Double-click the mapped drive
to access the iles and folders.
D-Link ShareCenter Pro 1100-04 User Manual
352
Section 4 - Knowledge Base
USB Print Server
The ShareCenter Pro features a built-in USB print server, giving users the ability to share a printer on their local network. Connect
a USB printer to the USB port on the back of the ShareCenter Pro. It is important to ensure that any of the printer manufacturer’s
drivers are already installed on any computer you want to print from.
To add a printer:
Click Start and select Printers and Faxes.
D-Link ShareCenter Pro 1100-04 User Manual
353
Section 4 - Knowledge Base
Select Add a printer.
The Windows® Add Printer Wizard will launch:
Click Next to continue.
D-Link ShareCenter Pro 1100-04 User Manual
354
Section 4 - Knowledge Base
When prompted to choose a local, or network
printer, select “A network printer, or a printer
attached to another computer.”
Click Next to continue.
Select “Browse for a printer” and click Next to
continue.
D-Link ShareCenter Pro 1100-04 User Manual
355
Section 4 - Knowledge Base
Select Double-click DNS-1100-04 from the
Shared Printers list to expand the tree.
Select the available USB printer, and click Next
to continue.
D-Link ShareCenter Pro 1100-04 User Manual
356
Section 4 - Knowledge Base
The following printer driver messages will appear:
Click Yes to continue.
Click OK to continue and select a
printer driver.
Select the appropriate printer driver from the list
and click OK to complete the wizard. If the driver
is not in the list, select Have Disk.
D-Link ShareCenter Pro 1100-04 User Manual
357
Section 4 - Knowledge Base
Insert the print driver CD or browse to the
appropriate directory.
Select the appropriate driver ile, and click
Open to continue.
Click OK to continue.
D-Link ShareCenter Pro 1100-04 User Manual
358
Section 4 - Knowledge Base
Verify the driver is correct, and click OK to
continue.
The wizard will install the printer drivers, and
return a completion screen. Click Finish.
D-Link ShareCenter Pro 1100-04 User Manual
359
Section 4 - Knowledge Base
The printer should now appear as an available
printer.
D-Link ShareCenter Pro 1100-04 User Manual
360
Section 4 - Knowledge Base
iSCSI Drive Mapping
The iSCSI Drive Mapping is used to manage the iSCSI settings on the ShareCenter Pro.
Carry out the following to conigure the iSCSI settings:
1. Click the listed ShareCenter Pro.
2. The available iSCSI target names in
the iSCSI Drive Mapping section appear.
Note: If you cannot see the latest list, click the Refresh button to update the status.
Note: You will need to create iSCSI volume in the Disk Management -> iSCSI Target. Click the iSCSI Targets tab to see the iSCSI
target name in this section.
D-Link ShareCenter Pro 1100-04 User Manual
361
Section 4 - Knowledge Base
The diferent parameters in the iSCSI Drive Mapping section are described below:
èéêë
ctive
ì
onnect/Disconnect
í
î
anagement
Displays the names of the available iSCSI
targets on the ShareCenter Pro.
Displays Yes if the target is active. Displays
No if the target is not active.
Choose a target from the list and click
the Connect/Disconnect button to
activate/deactivate the Target. If CHAP
authentication has been enabled, then a
username and password will be required.
Click the button to see the Management
window. The window allows you to add,
delete, mount and unmount the partition.
D-Link ShareCenter Pro 1100-04 User Manual
362
Section 4 - Knowledge Base
Coniguring Targets
1. When attempting to connect a target
for the irst time, choose the target from
the list
2. Click the Connect button.
3. If the CHAP is enabled, you will see this
window appears requesting CHAP User
and Password.
D-Link ShareCenter Pro 1100-04 User Manual
363
Section 4 - Knowledge Base
You will see the Format window.
The diferent parameters in the Format window are described
below:
arget
ðartition Size
ï
ormat Type
ñ
ò
rive Letter
Displays the iSCSI target name you chose.
Tick the Use Maximum Available Space
checkbox to specify that the maximum
available space on the disk will be used
to create the new partition. To specify
a size un-tick the checkbox and type
in the capacity size of the partition (in
megabytes) in the Megabytes ield.
Choose whether to format the new
partition with NTFS or FAT32 by ticking the
appropriate checkbox.
Choose the drive letter that you want to
allocate to the iSCSI partition from the
drop-down menu.
When you have inished coniguring the Target Settings, click
the Format button to see the window below
D-Link ShareCenter Pro 1100-04 User Manual
364
Section 4 - Knowledge Base
Coniguring Disks
This window appears after clicking the Format button. Or,
select a target in the iSCSI Drive Mapping list and click the
Management button to see the window.
The Management window allows you to manage partition
on the disks installed in the ShareCenter Pro and Mount /
Unmount the disks installed in the ShareCenter Pro.
The Disk Management section displays the following
parameters:
ó
isk
artition
ô
olume
õ
ile System
ö
apacity
÷
arget
ø
Displays the ID number of the disk
installed in the ShareCenter Pro.
Displays the partition number of the disks
partition.
Displays the drive letter that the partition
is mapped to on the client machine.
Displays the File System that the partition
was formatted with.
Displays the total capacity of the partition.
Displays the iSCSI target name of the
partition.
D-Link ShareCenter Pro 1100-04 User Manual
365
Section 4 - Knowledge Base
Adding a new partition
Right-click an unallocated partition and
click Add.
The Partition Manager window opens:
To add a partition, conigure the parameters as explained
below:
artition Size
ù
ormat Type
ú
û
rive Letter
Tick the Use Maximum Available Space
check box to specify that the maximum
available space on the disk will be used
to create the new partition. To specify a
size, un-tick the check box and type in
the capacity of size of the partition (in
megabytes) in the Megabytes ield.
Choose whether to format the new
partition with NTFS or FAT32 by ticking the
appropriate checkbox.
Choose the drive letter that you want to
allocate to the iSCSI partition from the
drop-down menu.
When you have inished coniguring the partition settings,
click the Format button to add the new partition.
D-Link ShareCenter Pro 1100-04 User Manual
366
Section 4 - Knowledge Base
Deleting an existing partition
Right-click an existing partition and click
Delete.
D-Link ShareCenter Pro 1100-04 User Manual
367
Section 4 - Knowledge Base
Mounting Disks
When a partition is not mounted, a * (star) symbol will appear in the Volume column in the Disk Management list.
Carry out the following steps to mount a disk:
1. Right-click an unmounted partition
and click Mount.
The Drive Select window appears.
2. Select the drive letter in the Device
drop-down list.
3. Click the OK button.
D-Link ShareCenter Pro 1100-04 User Manual
368
Section 4 - Knowledge Base
4. The mounted disk is displayed in the
Disk Management list.
3. The newly mounted disk is displayed
in the My Computer window and can be
used as if it was a locally attached disk.
D-Link ShareCenter Pro 1100-04 User Manual
369
Section 4 - Knowledge Base
Hot-swap
The ShareCenter Pro supports hot-swap drive trays. You can eject or insert 3.5” SATA hard drive(s) when the ShareCenter Pro
is operating.
However, if the hard drives are created into various levels of RAID, you cannot hot swap all the hard drives at the same time.
Hot swapping all the hard drives will cause a loss of data, and the RAID volume will need to be re-created again. Diferent levels
of RAID required various numbers of hard drives remaining in the ShareCenter Pro.
Standalone/JBOD/RAID 0: The data will be lost and the volume will crash, if any of the hard drives are hot swapped.
RAID 1: You can hot swap the hard drives as long as one of the hard drives in the mirror is still in the ShareCenter Pro. Removal
of all hard drives will result in a loss of all data and volume will have crashed.
RAID 5: In a RAID 5 volume, it is only possible to hot swap 1 hard drive at a time without losing all data. This is because a RAID
5 volume can only tolerate the loss of 1 hard drive and still continue to work. After hot swapping a hard drive, the
volume must irst be rebuilt before another hard drive can be hot swapped, otherwise this will also result in a loss of
all data and the RAID volume will have crashed.
You can check the RAID coniguration from the Disk Management -> Volume page on the Web UI. When hot swapping
hard drives, you will see the changes in the Disk(s) column. Hot swap one of the hard drives, make sure the Disk number has
disappeared from the Disk(s) column, and then hot swap the next hard drive.
D-Link ShareCenter Pro 1100-04 User Manual
370
Section 4 - Knowledge Base
Storing non-English Character Files
By default the ShareCenter Pro will support Unicode which is an industry standard allowing computers to consistently represent
and manipulate text expressed in most of the world’s writing formats.
D-Link ShareCenter Pro 1100-04 User Manual
371
Safety Declarations
CE Mark Warning:
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit diferent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link
oice.
D-Link ShareCenter Pro 1100-04 User Manual
372