Runco VIDEO XTREME VX-22I Specifications

O W N E R ’S O P E R A T I N G M A N U A L
VX-40d / VX-50d / VX-60d / VX-80d
Digital Cinema Projectors
Table of Contents
Limited Warranty ..................................................................................................................... v
Preface .................................................................................................................................. viii
Introduction.............................................................................................................................. 1
1.1 Projector overview ................................................................................................1
1.2 Components ........................................................................................................1
Installation and Setup ............................................................................................................. 3
2.1 Quick Setup .........................................................................................................3
2.2 Installation Considerations ....................................................................................5
2.3 Connecting Sources ...........................................................................................15
2.4 Connecting Communications ..............................................................................18
2.5 Power Connection ..............................................................................................19
Operation ............................................................................................................................... 21
3.1 About the Projector ............................................................................................21
3.2 Using the Remote or Built-in Keypad ...................................................................23
3.3 Navigating the Menus .........................................................................................30
3.4 Using Inputs and Channels .................................................................................34
3.5 Adjusting the Image ............................................................................................39
3.6 Adjusting System Parameters and Advanced Controls .........................................53
3.7 Working with the Lamp .......................................................................................62
3.8 Status Menu ......................................................................................................66
3.9 Error Conditions .................................................................................................67
Maintenance .......................................................................................................................... 71
4.1 Warnings and Safety Guidelines ..........................................................................71
4.2 Cleaning and Maintenance Guide ........................................................................74
4.3 Replacing Remote Batteries ................................................................................75
4.4 Lamp and Filter Replacement .............................................................................75
4.5 Replacing the Projection Lens .............................................................................78
5.1 Displays .............................................................................................................81
5.2 Lamp .................................................................................................................83
Specifications ........................................................................................................................ 85
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
iii
Table of Contents (continued)
Glossary ................................................................................................................................. 93
Serial Communications Cables ............................................................................................ 99
Throw Distance.................................................................................................................... 101
Optional Input Modules ...................................................................................................... 103
iv
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
TWO YEAR LIMITED WARRANTY
For Projectors, Video Processors and Controllers
Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe
Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup and care, you
should enjoy many years of unparalleled video performance.
This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and
retain it with your other important documents.
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
SERVICE LABOR: Runco will pay for service labor by a Runco Authorized Service Center when needed as
a result of manufacturing defect for a period of two (2) years from the effective date of delivery to the end
user (excluding the lamp).
PARTS: (Not including the lamp) Runco will provide new or rebuilt replacement parts for the parts that fail
due to defects in materials or workmanship for a period of two (2) years from the effective date of delivery
to the end user. Such replacement parts are then subsequently warranted for the remaining portion (if any)
of the original warranty period.
PROJECTOR LAMP: Runco will pay for service labor by a Runco Authorized Service Center when needed as
a result of a manufacturing defect for a period of six (6) months or 1000 hours, which ever comes first, from
the effective date of delivery to the end user. In addition, Runco will provide a new or rebuilt replacement lamp
for the lamp that fails due to defects in materials or workmanship for a period of six (6) months or 1000 hours,
which ever comes first, from the effective date of delivery to the end user. Such replacement lamps are then
subsequently warranted for the remaining portion (if any) of the original warranty period.
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
This Limited Warranty only covers failure due to defects in materials and workmanship that occur during
normal use and does not cover normal maintenance. This Limited Warranty does not cover cabinets or any
appearance items; failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication,
faulty or improper installation or setup adjustments; improper maintenance, alteration, improper use of any
input signal; damage due to lightning or power line surges, spikes and brownouts; damage that occurs
during shipping or transit; or damage that is attributed to acts of God. In the case of remote control units,
damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under
this Limited Warranty.
CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO
AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE
UNDER THIS LIMITED WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM
IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS
LIMITED WARRANTY.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
v
RIGHTS, LIMITS AND EXCLUSIONS:
Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty
period. There are no express warranties. Runco also excludes any obligation on its part for incidental or consequential
damages related to the failure of this product to function properly. Some states do not allow limitations on how long
an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential
damages. So the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights that vary from state to state.
EFFECTIVE WARRANTY DATE:
This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of
sale as evidence of the purchase date.
IMPORTANT: WARRANTY REGISTRATION:
Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly
if we should discover a safety problem or product update for which you must be notified.
CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:
Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at the
location of the product, during usual working hours, providing location of product is within normal operating distance
from a Runco Authorized Service Center. In some instances it may be necessary for the product to be returned to the
Runco factory for repairs. If, solely in Runco’s judgment, location of product to be repaired is beyond normal operating
distance of the closest Runco Authorized Service Center, or the repair requires the unit be returned to the Runco factory,
it is the owner’s responsibility to arrange for shipment of the product for repair. These arrangements must be made
through the selling Runco Dealer. If this is not possible, contact Runco directly for a Return Authorization number and
shipping instructions. Runco will return product transportation prepaid in the United States, unless no product defect is
discovered. In that instance, shipping costs will be the responsibility of the owner.
COPYRIGHT AND TRADEMARKS
© Copyright 2005 Runco International. This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other
means, in any form, without prior written permission of the manufacturer.
All trademarks and registered trademarks are the property of their respective owners.
vi
ADDITIONAL INFORMATION:
To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about
this Limited Warranty, please call or write:
RUNCO INTERNATIONAL, INC.
Attn: Customer Service Department
2900 Faber Street
Union City, CA 94587
Ph: (510) 324-7777
Fax: (510) 324-9300
Toll Free: (800) 23-RUNCO
RUNCO VIDEO PRODUCT INFORMATION
RETAIN THIS INFORMATION FOR YOUR RECORDS
Model Purchased
Date
Serial Number
Runco Authorized Dealer Name
Address
City
State/Province
Phone
Fax
vii
Postal Code
Preface
ABOUT THIS MANUAL
This manual is designed for use with the VX-40d, VX-50d, VX-60d and VX-80d
projectors. Information in this document has been carefully checked for accuracy;
however, no guarantee is given to the correctness of the contents. The information
in this document is subject to change without notice.
COPYRIGHT
© Copyright 2005 Runco International
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic or
other means, in any form, with out prior written permission of the manufacturer
TRADEMARKS
All trademarks and registered trademarks are the property of their respective
owners.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
viii
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
SECTION 1
Introduction
The Runco VX-40d, VX-50d, VX-60d and VX-80d Video Xtreme™ projectors are
professional 3-chip projectors based on next-generation Digital Light Processing™
(DLP™) technology by Texas Instruments™. These projectors are compatible with
standard international video formats and can interface with IBM®-compatible PC,
Macintosh® computers and workstations. All models deliver high-brightness, highresolution and high-quality images. Runco Video Xtreme™ projectors are an ideal choice
for most exclusive home theaters.
1.1 Projector overview
Key Features
•
Native SXGA+ resolution (1400 x 1050,
fully scaleable)
•
10-bit video processing
•
Built-in multi-standard video decoder
•
Replaceable Xenon lamp
•
Motorized lens mount
•
Auto-setup feature
•
Status LED display on built-in keypad for easy projector status monitoring
•
Control with IR or built-in keypad
Refer to Section 6 for a complete list of specifications including brightness and
contrast.
How the Projector Works
The projector accepts video input signals for projection onto front or rear flat screens.
High-brightness light is generated by an internal Xenon lamp then modulated by
three Digital Micromirror Device (DMD) panels that provide digitized red, green or blue
color information. Light from the “on” pixels of each panel is reflected, converged
and then projected to the screen through a single front lens, where all pixels are
perfectly superimposed as a sharp full-color image.
The following listed items are shipped with your projector. Ensure you have received all
these items before using your projector.
•
Owner’s Operating Manual (this document)
•
Programmable theater master remote (includes four, 1.5V AAA batteries)
•
Power cord
•
Warranty Card
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
1
1.2 Components
Section 1: Introduction
This page is intentionally left blank.
2
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
SECTION 2
Installation and Setup
Step 1
➤
Step 2
➤
Install the Projection Lens
The projection lens is shipped separately from the projector and must be installed prior to
setting up the projector. Install the projection lens as described in Section 4.5, Replacing
the Projection Lens.
2.1 Quick Setup
➤
The instructions provided here are for those that are familiar with the projector and wish
to quickly set it up and use it temporarily. Refer to the remaining subsections of this
manual for a more complete setup.
Step 3
Remove the lens plug from the lens opening in the projector before installing the
lens.
Remove the lens when shipping the projector and reuse the lens plug to prevent
dust and debris from entering and settling on critical optical components.
Position the Projector
Place the projector on a sturdy, level surface and position it so that it is perpendicular to
the screen at a suitable distance. In general, the further back the projector is positioned
from the screen, the larger the image will be.
If required, you can level the projector by adjusting its three feet. With the projector
positioned perpendicular to the screen the image will appear rectangular and not
keystoned.
For more detailed instructions on positioning the projector, refer to Projector Position and
Mounting later in this section.
Connect a Source
Located at the back of the projector is the input panel where all source connections are
made. Each input is clearly labeled for easy identification. Using the appropriate cable(s),
connect your source. Connect RGB and YPbPr sources to INPUT 1 located in the upper
right corner of the input panel. Use the DVI-I connector at INPUT 2 to connect analog
or digital display signals. INPUTS 3 and 4 (Composite and S-Video) are available but
generally not used since these signals would be input to the included DHD Controller.
NOTE: One of the available optional input modules can be installed at INPUT 5 or
INPUT 6 for additional connections.
Refer to Section 2.3, Connecting Sources, for more details on connecting a specific
source.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
3
Section 2: Installation and Setup
Step 4 ➤
Connect the Power Cord
NOTE: The North American rated power cord is provided with each projector.
Plug the power cord to the AC receptacle located on the right hand side of the projector
and the 3-pronged end into a grounded AC outlet. The input voltage to the projector must
be between 100 and 240 VAC in 1000W models (VX-40d and VX-60d) and between 200
and 240VAC in 1200W models (VX-50d and VX-80d). Refer to Section 6, Specifications,
for complete details on all power requirements.
Use the approved North American-rated power cord supplied with the projector. If you are
connecting to an area outside of North America make sure you are using an appropriately
rated power cord.
Step 5 ➤
Turn the Projector ON
Press the
POWER button on either the remote or built-in keypad to turn the projector
on, or turn the power on the DHD Controller (after fully connecting it to the projector),
which will also turn on the projector. Wait a few minutes to allow the projector to warm up.
The LED status window displays an active pattern of segments to indicate the projector is
changing its state from powered down to powered up. The message “On” appears in the
display when the projector has completed its initialization and is ready for use.
Step 6 ➤
Select a Source
Press one of the input keys on the remote or built-in keypad to select and display the
image for the source. With the DHD Controller, this would be either RGB (Input 1) or DVI
(Input 2).
Step 7 ➤
Adjust Image
To perform an “Auto-setup,” press FUNCS, then AUTO followed by Enter to initiate an
automated process in which the projector optimizes critical display parameters such as
size, position, pixel tracking etc. for the selected source. Press Enter again to keep the
new settings.
NOTE: You can also access the menu system and adjust these and other image settings
by pressing MENU on the remote.
4
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 2: Installation and Setup
Proper installation of your projector will ensure the quality of your display. Whether you
are installing a projector temporarily or permanently you should take the following into
account to ensure your projector performs optimally.
2.2 Installation
Considerations
Choose the installation type that best suits your needs: front or rear screen, floor mount
or inverted mount.
Front Screen, Floor Mount Installation
Advantages
• Easy to set up
• Can be moved or changed quickly
• Easy to access
Considerations
• Shares floor space with audience
Front Screen, Inverted Mount (ceiling) Installation
Advantages
• Does not take up audience space
• Projector is unobtrusive
• Projector cannot be accidentally moved
Considerations
• Installation is more permanent
• It is more difficult to access the projector
Rear Screen, Floor Mount Installation
Advantages
• Projector is completely hidden
• Projector is easily accessed
• Usually good ambient light rejection
Considerations
• Requires separate room
• Installation cost is usually higher
Rear Screen, Inverted Mount (ceiling) Installation
Advantages
• Projector is completely hidden
• Usually good ambient light rejection
Considerations
• Requires separate room
• Installation cost is usually higher
Rear Screen, Floor Mount with Mirror
• Projector is completely hidden
• Usually good ambient light rejection
• Requires less space behind screen than other
rear screen installations
Considerations
• Requires separate room
• Installation cost is usually higher
Front Screen Installations
In front-screen installations, the projector and audience are positioned in front of the
screen, which can be flat or curved.
Flat screens are recommended with this projector. They offer a gain of about 1 with
a viewing angle just less than 180°. This type of screen reflects incident light equally
in all directions so the audience can see the display from various angles.
Curved screens have a gain greater than 1 with a viewing angle much less than 180°.
This type of screen does not reflect incident light equally in all directions; instead,
it is concentrated in a viewing cone. The audience sitting within the viewing cone
area sees a brighter image than those sitting just outside this area. Runco generally
does not recommend use of curved screens with the Video Xtreme series, due to
excessive brightness and uncorrectable geometrical distortion.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
5
➤
Advantages
Screen Type
Section 2: Installation and Setup
Rear screen installations
There are two basic types of rear screens: diffused and optical.
A diffusion screen has a surface which spreads the light striking it. Purely diffused screens
have a gain of less than 1. The main advantage of the diffused screen is its wide viewing
angle, similar to that of a flat screen for front screen projection. This type of screen is
suitable when a wide viewing angle is required but there is low ambient room lighting.
Optical screens take light from the projector and redirect it to increase the light intensity at
the front of the screen. This reduces it in other areas. A viewing cone similar to that of a
curved, front-screen installation is created. This type of screen is better suited for brightly
lit rooms where the audience is situated within the viewing cone.
Screen size
Choose a screen size that is appropriate for your lens and application. The size of the
room and viewing distance are the defining factors; a rule of thumb is that the primary
viewing distance be 1.5 times the screen width.
To fill a screen with an image, the aspect ratio of the screen should be equal to the aspect
ratio of the image (expressed as the ratio of its width to its height). Standard video from
a VCR has a 4:3 or 1.33:1 aspect ratio. For example, to display a VCR output with a 4:3
aspect ratio onto a 10-foot (3m) high screen, the width of the screen must be at least 13.3
feet (4m).
6
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 2: Installation and Setup
➤
Ambient Light
➤
Other Considerations
➤
The high brightness of this projector is well suited for locations where ambient lighting
might be considered less than ideal for projection. A typical room with ceiling lights and
windows rarely requires special attention. Contrast ratio in your images will be noticeably
reduced only if light directly strikes the screen, such as when a shaft of light from a
window or floodlight falls on the image. Images may then appear washed out and less
vibrant.
Projector Position
and Mounting
In general, avoid or eliminate light sources directed at the screen.
Other considerations and tips that can help improve your installation:
•
Keep the ambient temperature constant and below 35°C (95°F). Keep the projector
away from heating and/or air conditioning vents. Changes in temperature may
cause drifts in the projector circuitry, which may affect performance.
•
Keep the projector away from devices that radiate electromagnetic energy such
as motors and transformers. Common sources of these include slide projectors,
speakers, power amplifiers, elevators, etc.
Throw distance
Throw distance is the distance measured from the projector’s lens to the screen. This
is an important calculation in any projector installation, as it determines whether or
not you have enough room to install your projector with a desired screen size and if
your image will be of the right size for your screen.
You can quickly estimate the throw distance by taking the width of the screen and
multiplying it by the lens throw ratio. See Figure 2.1. The result of this calculation tells
you roughly how far back the projector should be positioned from the screen in order to
project a focused image large enough to fill the screen. For example, using a 0.75:1 lens,
throw distance would roughly be 0.75 x screen width.
�������������������������
������������������������������������������������������������
���
���
����
����
�
�
��
Figure 2.1 Estimating Throw Distance
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
7
Section 2: Installation and Setup
Vertical and horizontal position
The correct vertical and horizontal position of the projector in relation to the screen
depends on the lens type and the screen size. Ideally, the projector should be positioned
perpendicular to the screen. This way, the image will appear rectangular instead of
keystoned (trapezoidal).
The vertical position of the image can be offset – that is, moved above or below
the optical axis (lens center) – by adjusting the fully motorized lens mount using the
keypad. The amount of vertical offset available depends directly on the lens installed
in the projector and can be slightly limited if horizontal offset has been applied.
Vertical offset can also be expressed as the percent of half the image height OR the
number of pixels of shift from lens center. See Figure 2.2 for some illustrated examples
of vertical offset.
Figure 2.2 Examples of Vertical Offset
8
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 2: Installation and Setup
Table 2.1, Table 2.2 and Figure 2.3 show the maximum vertical offset of a lens or
alternatively, how much of your projected image will appear above or below lens center if
the maximum vertical offset is applied using that lens.
Table 2.1 Lens Offsets for the VX-40d / VX-50d
Lens Type
Vertical Offset
(% of Half Height)
Maximum amount of
projected image above
or below lens center
Horizontal Offset
(% of Half Width)
Maximum amount of
projected image to one
side of lens center
%
Pixels
%
Pixels
%
Pixels
%
Pixels
0.8:1 fixed
37%
+/-196
69%
+/-721
22%
+/-153
61%
+/-853
1.6 - 2.0:1 zoom
100%
+/-525
100%
+/-1050
50%
+/-350
75%
+/-1050
2.0 - 2.7:1 zoom
100%
+/-525
100%
+/-1050
50%
+/-350
75%
+/-1050
2.7 - 5.0:1 zoom
100%
+/-525
100%
+/-1050
50%
+/-350
75%
+/-1050
5.0 - 8.0:1 zoom
100%
+/-525
100%
+/-1050
50%
+/-350
75%
+/-1050
% Offset = # pixels of offset / half panel resolution x 100.
Table 2.2 Lens Offsets for the VX-60d / VX-80d
Lens Type
Vertical Offset
(% of Half Height)
Maximum amount of
projected image above
or below lens center
Horizontal Offset
(% of Half Width)
Maximum amount of
projected image to one
side of lens center
%
Pixels
%
Pixels
%
Pixels
%
Pixels
0.73:1 fixed
37%
+/-196
69%
+/-721
22%
+/-153
61%
+/-853
1.45 - 1.8:1 zoom
100%
+/-525
100%
+/-1050
50%
+/-350
75%
+/-1050
1.8 - 2.5:1 zoom
100%
+/-525
100%
+/-1050
50%
+/-350
75%
+/-1050
2.5 - 4.5:1 zoom
100%
+/-525
100%
+/-1050
50%
+/-350
75%
+/-1050
4.5 - 7.3:1 zoom
100%
+/-525
100%
+/-1050
50%
+/-350
75%
+/-1050
% Offset = # pixels of offset / half panel resolution x 100.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
9
Section 2: Installation and Setup
Vertical Offset for 0.73:1 Fixed Lens
Vertical Offset for 1.6 - 2.0:1, 2.0 - 2.7:1, 2.7 - 5.0:1, 5.0 - 8.0:1 Zoom Lens
Figure 2.3 Lens Vertical Offsets
10
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 2: Installation and Setup
The horizontal position of the image can be offset – that is, moved to the left or right of
lens center – by adjusting the fully motorized lens mount. The amount of horizontal offset
available depends on the lens installed and if the image has already been vertically offset.
Horizontal offset can also be expressed as the percent of half the image width – the
number of pixels of shift to one side of lens center. See Figure 2.4 for some illustrated
examples of horizontal offset.
Also refer to Tables 2.1, Table 2.2 and Figure 2.5, which shows the maximum horizontal
offset of a lens or alternatively, how much of your projected image will appear to one side
of lens center if the maximum horizontal offset is applied using that lens.
Figure 2.4 Horizontal Offset Examples
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
11
Section 2: Installation and Setup
Horizontal Offset for 0.73:1 Fixed Lens
horizontal
Horizontal
Horizontal Offset for 1.6 - 2.0:1, 2.0 - 2.7:1, 2.7 - 5.0:1, 5.0 - 8.0:1 Zoom Lens
Figure 2.5 Horizontal Offset Examples
12
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 2: Installation and Setup
Mounting
There are several methods for mounting the projector. Depending on your chosen
installation, one method may be more suitable than another. In typical front and rear
screen installations the projector can be mounted to a secure and level surface, such
as a table or cart. Carts are useful when moving a projector during a presentation or
from site to site. If possible, lock the wheels when it’s in position to prevent it from being
moved during a presentation.
CEILING MOUNT—The projector can also be inverted and suspended from the ceiling
using a specially designed ceiling mount fixture. This type of mounting is recommended
for fixed installations and for those that want the projector out of sight or have a limited
space for projector and audience.
Use only the Runco-approved ceiling mount kit designed for your projector.
SPECIAL MOUNTING—The projector can be rotated (front-to-back) up to 360 degrees
and mounted without it affecting performance. However, the side-to-side tilt limit of
the projector must not exceed ±15 degrees. This tilt limit is required to ensure optimal
performance of the lamp. See Figure 2.6.
������
�����
Figure 2.6 Mounting Angle Ranges (Front-to-Back and Side-to-Side)
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
13
Section 2: Installation and Setup
Adjusting projector height
To compensate for a slightly unlevel mounting surface, you can modify the height of the
projector by adjusting the two feet threaded into the front bottom chassis. Turn each foot
clock-wise or counterclockwise until the projector is level on all sides. See Figure 2.7.
TURN
Adjust projector feet manually.
Figure 2.7 Projector Height Adjustment
Folded Optics
In rear-screen applications where space behind the projector is limited, a mirror may be
used to fold the optical path. See Figure 2.8. The position of the projector and mirror
must be accurately set. If you are considering this type of installation, call your dealer for
assistance.
Figure 2.8 Folded Optics
Runco Logo
The Runco logos on the front and rear of the projector
can be rotated to match a floor or ceiling installation.
To rotate the logo, grip it at the sides, pull it away from
the projector and rotate it 180 degrees.
14
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 2: Installation and Setup
Sources connect to the Input Panel located at the back of the projector. See Figure 2.9.
The upper right corner (INPUT 1) typically accepts an RGB signal from an external analog
RGB source, or it can also be used for YPbPr signals or additional video sources. The
DVI-I connector (INPUT 2) accepts digital or analog display signals from a computer.
INPUT 3 accepts and analog composite video signal; INPUT 4 an S-Video signal.
(Normally, however, you would connect these types of signals to the DHD Controller.)
2.3 Connecting
Sources
There are also several optional interfaces available for connecting other sources. These
interfaces slide into the remaining unused option slot, and can be done while the projector
is running.
From DHD Controller
RGB (BNC)
Figure 2.9 Input Panel
NOTES:
1) Refer to Section 6, Specifications, for details regarding compatible inputs.
2) Use only high-quality, shielded cables for all connections.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
15
➤
INPUT 1 consists of 5 BNC connectors and can be used as the input from the DHD
Controller. This projector supports multiple sync types with RGB signals: sync-on-green,
composite sync, and separate H and V syncs.
RGB Signals
Section 2: Installation and Setup
Fron DHD
Controller
Figure 2.10 Connecting RGB and Sync
NOTES:
1) If, for some reason, the projector fails to recognize a signal as an RGB signal, specify
this Color Space option within the Image Settings menu. Refer to Section 3.5,
Adjusting the Image.
2) To connect YPbPr signals – such as from DVDs or analog HDTV sources – to
INPUT 1, use the red, green and blue BNCs as described in YPbPr Signals (below).
YPbPr signals ➤
(COMPONENT VIDEO)
Connect a YPbPr signal (component video) to INPUT 1 or INPUT 2 as shown in
Figure 2.11.
NOTES:
1) If, for some reason, the projector fails to recognize a YPbPr signal, specify this Color
Space option within the Image Settings menu. Refer to Section 3.5, Adjusting the
Image.
2) Do not connect digital component signals (known as YCbCr) to INPUT 1. Install an
appropriate optional module in INPUT 5 or INPUT 6 for this.
Figure 2.11 Connecting YPbPr sources
16
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 2: Installation and Setup
INPUT 3 and INPUT 4 provide simultaneous connection of both a composite video
source (INPUT 3) and an S-Video source (INPUT 4), though typically these connections
would be made at the DHD Controller. See Figure 2.12.
Composite and S-Video
Figure 2.12 Connecting Composite or S-Video sources
➤
Use the DVI-I connector at INPUT 2 to connect either analog or digital video devices to
the projector. You can connect the DHD Controller here as well; if you do this, change the
Display Device setting on the DHD Controller to DVI.
DVI Digital Video
Use a cable with DVI-I connectors at both ends to connect devices that transmit digital
and analog video signals such as high-quality DVD players, satellite receiver and digital
cable TVs.
NOTES:
1) To ensure true digital output from devices that transmit digital signals, connect to the
DVI-I connector.
2) DVI loop through is not available unless you have the optional DVI Input Module
installed at INPUT 5 or INPUT 6.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
17
➤
Refer to Appendix D, Optional Input Modules, for a list of available optional input
modules.
Optional Inputs
Section 2: Installation and Setup
2.4 Connecting
Communications
Remote Keypads ➤
As desired, direct the projector’s IR remote keypad towards the projector’s IR sensors.
In normal operation, the DHD Controller will control the projector, but for setup and
calibration, use the projector remote.
Serial Port Connections ➤
There are two types of serial ports available on the projector: RS232 and RS422. The
RS232 port is used for communication with the DHD Controller, and subsequently the
RS422 port will be unused. If the projector is used as a standalone unit, either port could
be used for serial control.
Connecting RS232 from the DHD Controller
The 9-pin DIN connector labeled RS232 IN on the input panel is dedicated to serial
communication with the DHD Controller. Using the appropriate serial communication
cables and supplied adapter, connect the DHD Controller.
From DHD Controller
Figure 2.13 Connecting RS232 from the Controller
18
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 2: Installation and Setup
Connecting RS422
If you wish to control the projector with an automation system with RS422 capability and
a DHD Controller is not used (not recommended), connect a RS422 serial communication
cable between the automation system and the RS422 port on the projector. RS422 is better
suited for serial communication over long distances than is RS232 communication.
Use the RS422 port only if your device has RS422 capability — always consult the
literature provided with your equipment before connecting. Connecting to the RS422
port with incompatible equipment could damage your projector.
����������������
������������
Figure 2.14 Connecting RS422
Reserved for future use.
➤
Plug the power cord to the AC receptacle located at the back of the projector, below
the input panel, and the 3-pronged end into a grounded AC outlet. The input voltage to
the projector must be between 100 and 240 VAC in 1000W models (VX-40d and VX60d) and between 200 and 240VAC in 1200W models (VX-50d and VX-80d). (See also
Section 6 – Specifications for complete details on all power requirements.)
2.5 Power Connection
Use the approved North American-rated power cord supplied with the projector. If you are
connecting to an area outside of North America make sure you are using an appropriately
rated power cord.
Always power down the projector before unplugging the AC power cord. Wait
5 to 10 minutes for the main exhaust fan to turn off and for the lamp to cool sufficiently
before unplugging the projector.
WARNINGS
Do not attempt operation if the AC supply and cord are
not within the specified voltage and power range.
Wait for the cooling fans to turn off before unplugging the projector.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
19
Ethernet Port
Section 2: Installation and Setup
This page is intentionally left blank.
20
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
SECTION 3
Operation
This section explains how to effectively operate the projector once it has been installed.
Runco recommends that you read this section and familiarize yourself with the components
and the available menu options before you begin using your projector.
3.1 About the Projector
Projection Lens
Front IR Sensor
Adjustable Feet (2)
Status LED Display
Top IR Sensor
Built-in Keypad
Input Panel
Lamp Door
AC Receptacle
Non-adjustable Foot
Figure 3.1 Projector Basics
The built-in keypad is located at the back of the projector, beside the input panel. Use it
similarly to the IR remote to control the projector. A status LED display is also included on
this keypad for monitoring projector status.
➤
Built-in Keypad
The AC receptacle is located at the back of the projector just below the input panel. Use
this outlet to plug in an appropriately rated power cord. Refer to Section 6, Specifications,
for details.
➤
AC Receptacle
Located on the underside of the projector are two fully adjustable feet. Raise or lower
these feet when positioning the projector to ensure it is level on all sides so the displayed
image will appear rectangular without any keystone. NOTE: The third foot, located at the
rear of the projector (underside) is not adjustable.
➤
Adjustable Feet
Refer to Adjusting Projector Height in Section 2 for instructions on how to adjust the
projector’s feet.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
21
Section 3: Operation
Lens Mount and ➤
Projection Lenses
The projector is built with a motorized lens mount that allows for easy lens control and
adjustment. This includes such functions as adjusting vertical and horizontal offsets, zoom
and focus. The lens mount can be fitted with any one of the available optional lenses.
Refer to Section 6, Specifications.
•
Zoom and Focus — There are two internal lens motors that allow for quick
motorized adjustment of zoom and focus. Adjust zoom to fit the displayed image
on the screen and adjust focus to improve the clarity of the image.
•
Lens Offset — Vertical and horizontal offset is performed on the lens mount
through the use of DC motors.
•
Shutter — Standard on all models, the shutter allows you to turn the screen
absolutely black when in the “on” state. To operate the shutter, press the MUTE
button on the remote and hold it for 1-2 seconds. Or, press the Shutter button
on the built-in keypad.
•
Optical Aperture — Enables adjustment of light output and contrast ratio. The
optical aperture control is in the Advanced Image Settings menu (described later
in this section).
NOTES:
1) The projection lens is shipped separately from the projector.
2) Use the lens cap when transporting the projector to avoid scratching and damaging
the lens, which could affect your displayed image.
Input Panel ➤
Connect your signal sources to the input panel on the back of the DHD controller; refer
to the DHD controller manual for details. Connect the RGB and/or DVI output of the DHD
Controller to INPUT 1 and/or INPUT 2 respectively on the projector.
Cooling and Air Vents ➤
There are numerous air vents located around the projector. It is important these vents remain
unobstructed. Adequate airflow through the projector will prevent it from overheating.
Front and Top IR Sensors ➤
The two IR sensors located on the projector receive transmissions from the IR remote
from up to 100 feet away. It is important to keep the transmission path to these sensors
unobstructed for uninterrupted communications with the projector. The front IR sensor is
located next to the projector’s nameplate and the top IR sensor is located at the top of
the projector.
Lamp Door ➤
The lamp door is located at the back of the projector, which provides easy access to the
lamp module for replacement. Refer to Section 4.4, Lamp and Filter Replacement, for
lamp replacement procedures.
22
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
3.2 Using the Remote
or Built-in Keypad
➤
Keypad Commands
➤
Built-in
➤
The projector can be controlled using one of the following keypads:
IR Remote
• Built-in Keypad (located at the back of the projector)
• Theater Master Infrared (IR) Remote
Although each keypad provides complete control of the projector, they differ slightly in
their arrangement of keys and in what functions can be accessed directly with a key press
(as opposed to using the menu system). You may find one keypad more convenient than
another for your specific installation and application.
To control the projector when signals from a remote keypad cannot reach the projector,
use the projector’s built-in keypad. The nearby LED display provides feedback indicating
current status and activities of the projector. Because the built-in keypad has fewer keys
than the remote keypad, certain projector functions are accessible only through the menu
system rather than via a direct key.
Figure 3.2 Built-in Keypad
See Figure 3.3 and refer to the key function descriptions for the IR remote that follow.
The IR remote keypad controls the projector by way of wireless communications from
a battery-powered infrared transmitter. Use the IR remote keypad the same way you
would use a remote keypad supplied with a TV or VCR. When making key presses, direct
the keypad toward the front or top of the projector. One of the two IR sensors on the
projector will detect the signals and relay the commands for internal processing.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
23
Section 3: Operation
SYSTEM
1
MAIN
11
LENS
FUNCS
2
3
4
12
SOURC
+
GUIDE
13
PREV
CH
+
MENU
5
6
7
8
14
EXIT
INFO
9
15
DIS
10
Figure 3.3 Theater Master IR Remote Control
24
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
POWER Button
Hold this button down for 1-2 seconds to turn on or off the projector.
2.
FUNCS Button
This button brings you to a sub-page in which you can access the projector’s
internal test patterns, view help text, auto-calibrate the projector and perform
various other functions.
3.
BACKLIGHT Button
Lights the LCD display and buttons for use in a dark room.
4.
LCD Display
Displays currently-selected LCD Menu page.
5.
MAIN Button
Brings up the Main LCD Menu page.
6.
MUTE Button
Activates the Shutter control on the projector. Press and hold for 1-2 seconds to
activate the shutter, and press and hold again to de-activate the shutter.
7.
MENU Button
Displays or hides the on-screen projector menu.
8.
ENTER Button
Though it has a ‘stop’ icon (and can be programmed as such for other sources),
this button serves as an ‘ENTER’ button for the projector when navigating through
the menus.
9.
Numeric Keypad
Used for entering numeric values or passcodes. Also allows direct selection of
numbered on-screen menu items.
10.
ENTER Button
Same as 8.
11. LENS Button
Brings up the lens adjustment LCD Menu for making zoom, focus and shift
adjustments.
12.
SOURC Button
Brings up the projector’s source selection LCD Menu.
13.
Directional Keypad
Used for navigating through the on-screen projector menus and adjusting values.
14. EXIT Button
When in the menu structure, the EXIT button brings the menu back one page or
cancels the current function.
15. FUNCTION Button
Though labled ‘DIS,’ this button has been programmed as a ‘FUNCTION’ button
used in several menu items. (You can also use the FUNCN button in the Functions
LCD Menu.)
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
25
➤
1.
Remote Control
Button Descriptions
Section 3: Operation
Guide to Keypads ➤
Keep in mind the following guidelines:
•
Press keys one at a time; there are no simultaneous key combinations required.
•
Note that two keys, POWER and MUTE, are “press-and hold” keys that do not
function with a typical quick press-and-release key press.
•
Hold arrow keys down for continuous adjustment/movement in one direction.
•
If you press a key while the projector is still responding to the previous action,
such as during power-up, the second key press may not take effect.
Specific keypad commands are explained below:
Keypad commands ➤
Power ON/OFF
Press and hold
for two seconds to toggle the projector on or off with a single keystroke.
Or press and release
followed immediately by ▲ (on) or ▼ (off) to guarantee the correct
toggle (useful if you are unsure of the present state).
NOTES:
1) After powering down, the lamp cooling fan remains on for approximately five minutes
to cool the lamp.
2) Avoid turning the projector back on until it has been off for a few minutes. Hot restrikes of the lamp may reduce lamp life.
LCD Menu ➤
The IR remote has its own menu structure, independent
of the on-screen menus. The IR remote menus provide
convenient shortcuts for selecting the signal source,
operating the lens and performing certain other
projector functions.
MAIN
LENS
FUNCS
SOURC
26
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
LENS (Focus, Zoom and Lens Shift)
Press LENS to adjust the image for focus, zoom and horizontal and vertical positioning.
A small window appears on the screen to indicate the type of adjustment taking place.
•
FCUS▲ / FCUS▼: Use the FCUS▲ and/or FCUS▼ keys to improve image
clarity.
•
LENS▲ / LENS▼: Use the LENS▲ and/or LENS▼ keys to adjust the vertical
position of the image.
LENS
FCUS▲
LENS▲
FCUS▼
LENS▼
ZOOM+
LENS◄
ZOOM-
LENS►
PAGE 1
•
ZOOM+ / ZOOM-: Use the ZOOM+ and/or ZOOM- keys to achieve the desired
image size.
•
LENS◄ / LENS►: Use the LENS◄ and/or LENS► keys to adjust the horizontal
position of the image.
To shift the lens using the built-in keypad, press the LENS SHIFT button on that
keypad, then use the directional buttons (◄►▲▼) to position the image. Press
Exit when finished.
FUNCS
Press FUNCS to access the projector’s help text, internal test pattern and “Auto Setup”
features.
•
HELP: Press HELP to display on-screen help text. Press HELP again (or Exit)
to hide it.
•
TESTP: Press TESTP and then use the left- and right-arrow keys (or press
TESTP repeatedly) to cycle in either direction through the test patterns only (no
input). Press Exit to get out of the test pattern mode.
•
FUNCN: This is a general-purpose “function” key used in various places throughout
the menu system.
Note: The FUNCN button (on the FUNCS sub-page in the LCD menu) and the
DIS button (next to “0” on numeric keypad) can be used interchangeably.
•
CHANL: Press CHANL to access the Channel Selection menu. This menu lets you
select a specific source setup (channel) defined and stored in projector memory.
When you enter a 2-digit channel number (or, if there is a list displayed, highlight
it and press Enter), the display automatically changes and updates according
to the numerous setup parameters defined for that channel. Note that a new
channel is automatically created if you adjust an image from a new source.
NOTE: Channel (CH) key behavior during a presentation depends on whether or
not the Display Channel List option is enabled in the Menu Preferences menu.
You can use the scrollable list of channels when you press CHANL, or you may
prefer to enter the desired channel number “blind;” that is, without on-screen
feedback. Refer to Menu Preferences later in this section.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
27
FUNCS
HELP
TESTP
FUNCN
CHANL
AUTO
PAGE 1
Section 3: Operation
•
AUTO: Select AUTO to initiate an automated process in which the projector
optimizes critical display parameters for the current source. Table 3.1 lists these
parameters. An Auto Setup allows you to quickly get the image “in the ballpark,”
after which you can (and in most cases, should) perform further calibration.
Table 3.1 Auto Setup
What an “Auto Setup” Does
OPTIMIZES:
SETS TO DEFAULT:
Pixel Tracking
Contrast
Pixel Phase
Brightness
Size and Blanking
Auto Input Level (off)
Vertical Stretch
Detail (if video source)
Position
Filter
Input Levels
Luma Delay
NOTE: You must have an unlocked channel present to use Auto Setup. For more about
channels, refer to Using Inputs and Channels, later in this section.
SOURC
RGB
DVI
INPT3
INPT4
INPT5
INPT6
PAGE 1
SOURC
Press SOURC to select the desired input signal source:
•
RGB: Press RGB to display from the data or video input source connected to
the BNCs at Input 1.
•
DVI: Press DVI to display from the DVI source connected to Input 2.
•
INPT3: Press INPT3 to display from the composite video source connected to
Input 3.
•
INPT4: Press INPT4 to display from the S-video source connected to Input 4.
•
INPT5: Press INPT5 to display from the Input 5 interface module installed in the
Option 1 slot.
NOTE: If you have the optional Dual SD/HD-SDI Module installed and there are two
inputs connected to it, the second input is considered Input 7. If you are using the
built-in keypad or the remote keypad, press INPT5 to access Input 7 as follows:
•
While displaying from Input 5, press INPT5 again. This switches to Input 7.
28
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
•
INPT6: Press INPT6 to display from the Input 6 interface module installed in
the Option 2 slot.
NOTE: If you have the optional Dual SD/HD-SDI Module installed and there are two
inputs connected to it, the second input is considered INPUT 8. If you are using
the built-in keypad or the remote keypad, press INPUT 6 to access INPUT 8 as
follows:
•
While displaying from Input 6, press INPT6 again. This switches to Input 8.
•
While displaying from any input other than the Dual SD/HD-SDI Module, press
Input 6. This switches to either Input 6 or Input 8, depending on which of the
Dual SD/HD-SDI Module inputs was last used. Press INPT6 again to display
from the other Dual SD/HD-SDI Module input.
MUTE (Shutter)
Press and hold MUTE on the Theater Master remote for two seconds to toggle the
internal mechanical shutter blade closed or open with a single keystroke.
A closed shutter blanks the display (turns it to black). Close the shutter to mute all
display while maintaining access to projector functions. Opening the shutter restores the
image.
NOTES:
1) “Sh” appears in the LED display when the shutter is closed.
2) The shutter is open upon power-up.
Menu
Press Menu to enter or exit the projector’s menu system.
Function (FUNCN / DIS) Key
Note: The FUNCN button (on the FUNCS sub-page in the LCD menu) and the DIS
button (next to “0” on numeric keypad) can be used interchangeably.
DIS
IF WITHIN A MENU: Press FUNCN to perform special tasks within the menu system,
as described with the appropriate topic later in this section. For example, press FUNCN
while in the Channel Setup menu to delete or copy a channel.
IF WITHIN A PRESENTATION: Press FUNCN or DIS
followed by a 2-digit number to enable a specific color or
colors in the display (see right). For example, FUNCN 6 4
displays only red and green data and FUNCN 6 7 displays all
color data. Eliminating one or more colors can help with certain
diagnostics and setups, such as when accurately overlaying
one image on top of another from stacked projectors.
���
���
���
���
���
���
���
NOTE: Color enabling can also be implemented from numerous locations within the
menu system.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
29
Section 3: Operation
Enter
Press Enter to select a highlighted item, to toggle a checkbox or to accept a parameter
adjustment and return to the previous menu or image.
Exit
Press Exit to return to the previous menu.
NOTE: Exit does not save changes within text editing boxes (including number editing of
a slidebar value) or within pull-down lists. It acts as a “cancel” in these cases.
Directional Keypad
The directional keypad (large, black button just above the numeric keypad) behaves
similarly to a joystick.
Press the left or right side of this button to change a slidebar value or to select a different
option within a pull-down list without having to first scroll through options. (Also refer to
Editing Text, later in Section 3.) Press the top or bottom of this button to navigate within a
menu, pull-down list or text box.
3.3 Navigating the
Menus
Most of the controls for the projector are accessed from within the projector’s menu
system. There are several groups of related functions, with each group selectable from the
Main Menu, shown in Figure 3.4. Press MENU at any time to display this menu.
�������������������
Figure 3.4 Runco Video Extreme Main Menu
On the remote keypad, do one of the following:
•
Enter the number corresponding to the function menu you wish to access, such
as 2 for the Image Settings menu.
•
Press ▲ and/or ▼ on the directional keypad to highlight the desired option, then
press Enter or ►.
The corresponding function menu or pull-down list of further options will then
appear.
You navigate the function menus in a similar manner: enter a menu option number for any
numbered option, or use the ▲ and ▼ keys to highlight the desired option, then press
Enter. Extra long menus have a scroll bar on the right; use the arrow keys to access the
remainder of the menu. Locked items or items that do not pertain to the current action or
condition appear dimmed and cannot be selected.
30
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
NOTES:
1) If there is no signal present, all source-dependent adjustments are disabled.
2) After 15 minutes of inactivity, the projector leaves the menu system and returns to
the presentation.
3) The Status menu is read-only.
When finished with a function menu, do one of the following:
• Press Exit to return to the previous screen.
• Press MENU to leave the menu system and return to the presentation.
If at any time you are uncertain what to do next, press HELP to display summary
information about the current menu or highlighted option; see Figure 3.5. Press HELP
again to exit. In addition, a line of “hint” text is included at the bottom of some menus.
➤
Help
If a slidebar, menu or message is displayed you have limited time in which to make
a keypad entry before the projector returns to presentation level and the graphic
disappears. These time-outs may vary depending on what is displayed.
➤
Time-outs
Menu options that include this icon apply universally to any incoming
signal.
➤
The Global Icon
Figure 3.5 Context-sensitive Help
From presentation level, press HELP to access general Help Topics (Figure 3.6). Scroll as
necessary within a topic. Press HELP or Exit to return to your presentation.
Figure 3.6 Accessing General Help Topics
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
31
Section 3: Operation
Using Slidebars and Other ➤
Controls
Most of the function menus allow you to change settings by using slidebars, checkboxes
and pull-down lists. To select a slidebar, toggle a checkbox status or view a pull-down
list, do one of the following within the function menu:
•
Enter the menu option number corresponding to the setting you wish to change
(for example, press MENU 1 3 to select Vertical Stretch in the Size and Position
menu).
•
Move the highlight to the option desired and press Enter.
•
Move the highlight to the option desired and press ◄ and/or ► to adjust
immediately.
•
Bypass the menus entirely and use a single key to immediately access an
adjustment during your presentation. This applies only to options having their
own key, such as Focus (FCUS) or Zoom.
•
For “blind” access, hide the entire menu system (see OSD key, above) and/or
direct slidebars activated by their own key (such as Contrast, Brightness, etc.).
Control by using the proper keypress or numerical sequence of key presses.
Once selected, change the setting as desired and press Enter to save and return to
the current function menu.
Slidebars in menus — The current value for a given parameter,
such as size or vertical stretch, appears to the left of its slidebar
icon (adjustment window). This number often expresses a percentage, or it may have
units associated with it (such as pixels or kelvin), depending on the specific option. Press
◄ ► to gradually adjust the setting up or down—both the number and the length of the
bar change accordingly. Hold for continuous adjustment. Or, press Enter to activate a
slidebar text box for specific number entry via the keypad, then press Enter to save or
Exit to cancel.
Checkboxes — Conditions are present if its adjacent
checkbox contains a checkmark. To toggle the checkbox,
highlight it and press Enter, or highlight and use ► to check and ◄ to uncheck. If a
checkbox is numbered, simply enter its number to immediately toggle the checkbox.
Pull-down lists — To see a pull-down list of options available for a given parameter
labeled with a ▼, highlight it and press Enter, or enter the menu option number.
Use ▲ or ▼ keys to navigate up and down within the list (the current choice is noted with
a small ►). Press Enter to choose an option from the list.
Figure 3.7 Example of Pull-Down List
32
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
If you prefer to quickly scroll through a list without first pulling it down, highlight the
option and use ◄ or ►. Press Enter when the desired choice appears.
NOTES:
1) Long pull-down lists consist of two or more “pages.” To jump between pages, press
◄ or ►.
2) Press Exit while in a pull-down list to cancel any change.
➤
Editing Text
➤
ACTIVATE THE EDIT WINDOW: To enter or edit text, highlight the desired parameter
(such as a channel name) and press Enter to activate its adjacent edit window. Any
previously entered text is displayed with its first character highlighted in a square cursor,
signifying that this character is ready for editing.
Editing Numerical Values
NAVIGATE WITHIN THE EDIT WINDOW: Press ► to move the cursor forward or ◄ to
move the cursor backwards as desired.
EDIT A CHARACTER: To edit a highlighted
character, use ▲ and ▼ to scroll through the
alphabet, numbers, spaces and punctuation
available. When the character you need appears,
press ► to select it — the cursor will move to
the next character of current text, if present.
Note that you can also enter a number directly
from the keypad — it will be accepted and the
cursor will move on.
Figure 3.8 Entering Text
INSERT A SPACE OR DELETE A CHARACTER: To insert a space at the cursor
location, press FUNCN (or DIS) followed by ►. To delete a highlighted character (or
space), press FUNCN followed by ◄.
FUNCN
FUNCN
PRESS ENTER WHEN FINISHED: To accept edits and leave the edit window, press
ENT (Enter). To cancel changes and return to the previously-defined text, press Exit at
any time.
Enter numbers directly from the keypad in order to specify numbers representing
projectors, channels (source setups) or slots. As each digit is entered, it is displayed
and the cursor moves on. Note that channel numbers are defined with 2 digits—for
example, if you enter only a single digit (such as “7”) for a channel number, the channel
will automatically be defined as “07”. Enter “07” to utilize this channel.
NOTES:
1) Once you enter the first digit, this digit replaces all old digits.
2) If you press any non-numbered key, the number entered up to that point is accepted
and updated as the new value.
3) Press Exit to cancel editing of numerical values.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
33
Section 3: Operation
3.4 Using Inputs and
Channels
NOTE: See Section 2, Installation and Setup, for details on connecting sources to
the projector.
The projector stores and automatically recalls up to 50 different channels (source setups)
for a variety of inputs. This memory feature allows you to define and conveniently use
a wide variety of customized setups rather than having to repeatedly re-configure the
projector for different presentations. Each physical source connection (i.e., input at the
projector) can have several different channels associated with it.
NOTE: Channels are pre-configured at the Runco factory for use with the DHD
Controller, and do not necessarily need to be changed. The following information applies
only if other sources are connected directly to the projector.
Do I Select an Input ➤
or a Channel?
INPUT — An input is a source physically connected at the projector. Input describes the
source signal according to which input slot it is connected.
SWITCHING INPUTS — Press SOURC followed by the appropriate “direct” key (RGB,
DVI, INPT3, INPT4, INPT5 or INPT6) to quickly display from one of the six inputs
connected. The image will be displayed according to the following:
If it is the first time you have used the source/input (or if you used the input but
did not define a channel by adjusting anything), the projector will recognize the new
input signal based on its frequencies and polarities, and will automatically display an
image according to default settings for such a signal. In general, the image from the
new source will be as large as possible without losing its aspect ratio. This and other
default image settings depend on the incoming source.
If you used the source once before and changed a display parameter such as
contrast, V-Position, etc., then a channel was automatically created and still exists in
projector memory (see below). Using one of the Input keys will automatically recall this
channel—and all its setup parameters—and update the display accordingly.
If more than one channel exists for the input, the image will be displayed according
to the setup parameters for the first channel with matching characteristics.
NOTE: Inputs 7 and 8 require the Dual SD/HD-SDI module in either of the projector’s
option slots. For their selection, see also 3.2, Using the Remote or Built-In Keypad.
CHANNEL — A channel is a collection of measurements, locations and settings that
tailor the display of a signal to your specific needs. Since source types and applications
can vary greatly, you will likely want to adjust and define a wide variety of parameters,
such as brightness, contrast, size etc., in order to customize and optimize the display
from or for a particular source. For example, the display settings you choose for a VCR
source may be very different from those you choose for a high resolution computer
source, or one signal may simply vary from another signal used previously through
the same input location. Once you have adjusted a display parameter, such as pixel
tracking or contrast, all current settings are collectively stored in the projector’s memory
as a unique 2-digit channel, such as 0 9. You can have numerous distinct channels
available for the same input, any of which can be selected by pressing FUNCS then
CHANL on the keypad, followed by the two-digit channel number.
34
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Shown at right is a sample channel list.
CHNL
NOTE: The Channel key may display a channel list
or not, depending on the current “Display Channel
List” setting (refer to Menu Preferences later in this
section).
Channel List
When you select a direct input (RGB, DVI, INPT3, INPT4, INPT5 or INPT6) any existing
channels in the projector are searched for matching input and signal parameters – this
only occurs if Auto Source is enabled on these channels. If no match to the incoming
input signal is found in currently-defined channels, a new channel is temporarily created
based on factory-defined defaults for this type of signal. The channel number assigned is
the lowest available number from 01 to 50.
NOTES: 1) An automatic channel will be discarded unless one or more of its parameters
are changed and will not appear in the channel list (see below). 2) If two channels have
the same distinguishing source characteristics except for the reversal of sync connectors
(i.e., H-sync and V-sync, are switched), they are still defined as distinct channels. 3) You
cannot define a new channel without an incoming signal.
If the incoming signal does match an existing channel, the image will be set up and
displayed as usual according to the parameters currently defined for that channel.
USING A CHANNEL: You can
normally select a channel at any
time by pressing CHNL (see right).
If you want to prevent a channel
from appearing in this list, you
must edit the channel as described
in Channel Edit later in this section.
Such a channel can still be selected
by entering its number as shown at
right.
CHNL
NOTES: 1) The current channel is highlighted upon entering the channel list, or, if this
channel is not displayed here, the first channel in the list is highlighted. 2) Channels
created automatically do not appear in the channel list unless a parameter for the channel
has been changed.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
35
➤
To use a new source with the projector, you must add a new channel to projector
memory so that the projector will respond properly to an input signal from that source
in the future. A new channel can be created automatically, as described here, or it
can be copied from an existing channel and then edited as necessary (see Copying
or Deleting Channels later in this section).
Creating a New Channel
– AUTOMATIC –
Section 3: Operation
What Channels ➤
Are Defined So Far?
All available channels are
listed in the Channel Setup
menu, which describes
how each channel can be
accessed and which serves
as the gateway for editing,
copying
and
deleting
channels.
Figure 3.9. Typical Channel Setup Menu
From the presentation level, press MENU to display the Main Menu. To display the
Channel Setup menu, press 3 or highlight Channel Setup and press Enter or ►. The
Channel Setup menu appears with the active channel highlighted.
WHAT APPEARS IN CHANNEL SETUP MENU? This menu lists all channels defined so
far and indicates where they are connected on the input panel.
The far left column lists channel numbers currently defined. The
values in the far right columns indicate horizontal and vertical
frequencies—if someone has defined a name for this channel,
it appears here instead. Remaining columns contain details pertaining to each channel
setup, such as its switcher number (always 0 = projector), slot location, a variety of icons
indicating access to each channel, and an abbreviated description of each signal type.
Refer to Editing a Channel Setup for details.
NOTE: If you have more than a handful of channels, use ◄ and ► to see the remaining
channels not visible in the initial display of channels.
SIGNAL TYPE — Either channel list, whether the Channel key list or the Channel Setup
menu, identifies signal types in a shortened form, as shown in Table 3.2. These descriptors
indicate what signal information the projector uses to identify a match for a given channel,
and are preceded by either an “i” (for interlaced signals) or “p” (for progressive signals).
Table 3.2. Signal Type Abbreviations
Abbrev.
Signal Type
4WH
Composite (4 wire) on HC input
4WV
Composite (4 wire) on V input
SG
Sync-on-green
5W
Separate H,V
5WR
Separate H,V swapped
SVid
S-Vid
CVid
Composite Video
Dig
Digital
36
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
FUNCTIONS WITHIN THE CHANNEL SETUP MENU — To copy, delete or edit a
channel, highlight the desired channel in the Channel Setup menu and either:
Press FUNCN (or DIS) if you want to copy the selected channel or delete this
or other channels (refer to Copying or Deleting a Channel, below); or
•
Press Enter if you want to edit channel setups (i.e., non-image related parameters)
for the selected channel. Refer Editing a Channel Setup.
TO COPY A CHANNEL, highlight the desired channel in the Channel Setup menu, then
press DIS to go to the Channel Copy/Delete submenu. Select “Copy” and press Enter.
This creates a new channel that is identical to original -- which remains -- but it is identified
with the next available number from 01 to 50. If you change your mind and do not want to
copy the current channel, press Exit to cancel and return to the previous menu. Copying
channels is a quick way to create numerous channels, each of which can then be edited
and adjusted for a variety of presentations in the future.
Figure 3.10. Copying A Channel
TO DELETE A CHANNEL, highlight the desired channel in the Channel Setup menu,
then press DIS to activate the Channel Copy/Delete submenu. Select “Delete” and press
Enter. A confirmation window appears. Press Enter again to confirm the deletion or
select Cancel if you change your mind.
�����
Figure 3.11. Deleting a Channel
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
37
➤
•
Copying or Deleting
Channels
Section 3: Operation
TO DELETE MULTIPLE CHANNELS, highlight any channel in the Channel Setup menu
and press DIS (or FUNCN) to go to the Channel Copy/Delete submenu. Select “Delete
Unlocked Only” and press to delete all unlocked channels. Or select “Delete All Channels”
to delete all channels, even those that are locked. In either case, the current channel will
remain but will be redefined from projector defaults.
NOTE: For any deletion, a confirmation box appears to make sure that you really want to
delete. Select “Cancel” (default) if you don’t want to delete after all.
Editing a Channel Setup ➤
The basic setups that describe how and where a channel can be accessed are listed in
the Channel Setup menu. These channel setups can be edited at any time in the Channel
Edit submenu.
CHANNEL EDIT — STEP 1
From the presentation level press MENU to display the main menu. To display the Channel
Setup menu, press 3, or move the highlight to the Channel Setup option and press Enter
or ►. The Channel Setup menu will appear.
CHANNEL EDIT — STEP 2
To edit parameters shown in the Channel Setup menu, select the relevant channel and
press Enter or ►. The Channel Edit menu, shown in Figure 3.12, appears.
Figure 3.12. Typical Channel Edit Menu
CHANNEL EDIT — STEP 3
If desired, review and/or edit the following channel setups in the Channel Edit menu:
•
CHANNEL NAME: An alpha-numeric label can be defined and/or changed here.
Channel names can be up to 12 characters in length.
•
CHANNEL NUMBER: A 2-digit channel number can be changed here.
NOTES: 1) If you enter a channel number that already exists, a dialog message
appears indicating that this number is already in use – assign a different channel
number. 2) You can define up to 50 channels.
•
INPUT: 1-8, corresponding to where on the projector’s input panel the source is
connected.
•
IN MENU: If checked (default, except for automatically defined channels with
unchanged parameters), this defined channel will then appear in the list available
when CHANL key is pressed. If unchecked, the channel must be accessed via
CHANL on the keypad or via the Auto Source function.
NOTE: To enable or disable on-screen display of the Channel List, use the Menu
Preferences menu (described later in this section).
38
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
•
AUTO SOURCE: If checked, (default), the projector can automatically locate this
channel when an incoming input signal matches. If not checked, the projector
can locate the selected channel only when it is directly selected via CHANL on
the keypad—and a change in input signal will not result in a channel change.
•
LOCKED: If checked, all of the image settings for this channel are disabled. If
unchecked (default), all available image settings can be adjusted as desired. You
cannot use Auto Setup with a locked channel.
•
PREVIOUS CHANNEL: Select this option to see or change Channel Edit settings
for the previous channel in the Channel Setup list.
•
NEXT CHANNEL: Select this option to see or change Channel Edit settings for
the next channel in the Channel Setup list.
The most commonly used options for image adjustments are accessed through two
menus: Size and Position (MENU 1) and Image Settings (MENU 2), both of which appear
in the Main menu. From either of these two menus, you can change settings affecting the
image from the current channel by working with the appropriate slidebars, checkboxes
and pull-down lists. Exit will return to the previous menu (or to the presentation, if from
the Main menu) and accept any changes you may have entered. Settings are saved with
the current channel.
3.5 Adjusting the
Image
From your presentation, you can access any of the individual options in these menus by
pressing MENU followed by the appropriate two-digit number representing their location
in the menu system. For example, press MENU 2 3 to quickly access the “Gamma”
option in the Image Settings menu.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
39
➤
Use Auto Setup (AUTO)
For a good and efficient first step in perfecting the image, press FUNCS followed by AUTO
on the remote control. This initiates an automated process in which the projector quickly
optimizes critical display parameters such as size, position and pixel tracking, based on
the type of incoming source data detected. An Auto Setup can save considerable setup
time, and you can still modify the adjustments as desired using menu options described
below.
Before You Begin
Section 3: Operation
Size and Position Menu ➤
In the Size and Position Menu,
you can increase or decrease
the size of your image, change
its proportion (aspect ratio),
move the image to a specific
area of the screen, and refine
other related parameters. Use
Size and Position controls to
match the image precisely to
the screen used at the site.
Refer to Using Slidebars and Other Controls (earlier in this section) if you need help using
any of the options and controls. Changes made in the Size and Position menu take effect
immediately and are saved when you exit the menu (press Exit or MENU).
Resize Presets
Select a Resize Presets option to quickly display an image in its native resolution or to
automatically resize an image to
closely fill the projector’s native
resolution of 1400 x 1050, or
to optimize the width or height
of your display. Size, Position
and Blanking parameters will
automatically adjust accordingly,
or if Blanking is set first, which
defines an Active Input Area,
Resize Preset scaling will occur
in this region of interest only.
Resizing options are explained in
detail below.
WHAT IS THE RESIZING DEFAULT? By default, when you select a new source, the
image utilizes as much of the projector’s display area (1400 x 1050) as possible for the
type of incoming source data, but with minimal or no changes to aspect ratio. See Select
“Default,” below.
WHEN “CUSTOM” APPEARS: The “Custom” re-size descriptor automatically appears
in the Size and Position menu when any of the values for Size, Vertical Stretch, H-Position,
V-Position or Blanking do not correspond to those for a preset. This option is not offered
in the Resize Presets pull-down list.
•
Select “DEFAULT” for most sources (factory default). The image will be centered
and displayed as large as possible depending on the type of source, as described
below:
✔A 5:4 graphic image will enlarge to fill the screen height, and be centered between
narrow black side bars.
✔A video image or 4:3 graphic image will enlarge to fill the screen.
✔An anamorphic (16:9) image will fill the width and be centered between black
bars on top and bottom.
40
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
•
Select No Resizing to display the image in its native resolution, which may or
may not match the projector’s 1400 x 1050 resolution. For example, for a source
with a native resolution of 800 x 600, “No Resizing” will use the central 800 x
600 pixels and have a black border—the black border areas are unused areas.
•
Select Full Size to use
all pixels (1400 x 1050)
for displaying the image,
regardless of source
or original aspect ratio.
Incoming source material
having a different aspect
ratio than the projector will
be stretched for display.
•
Select Full Width to fill the
projector’s display from leftto-right without changing the
original aspect ratio of the
image. Depending on the
source, data at the top and
bottom may be discarded
(cropped), or the display
may have black borders at
the top and bottom (called
“letterbox”).
•
Select Full Height to fill the
display from top-to-bottom.
Depending on the source,
this may create borders.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
41
Section 3: Operation
•
Select Anamorphic to display an anamorphic image in
its native 16:9 aspect ratio. The image will fill the screen
from side-to-side and be centered between black bars
at top and bottom.
NOTE: If using a 16:9 screen, you may have to go to the
Anamorphic mode after performing an auto setup.
Size
“Size” controls both the image width and height in tandem, maintaining the current aspect
ratio (proportion) of the displayed signal data.
Vertical Stretch
“Vertical Stretch” adjusts the height of the image while keeping the width constant. Use
Vertical Stretch to change the aspect ratio of the display.
Pixel Track
Steady flickering or several soft vertical stripes or bands across the entire image indicates
poor pixel tracking. Proper pixel tracking helps ensure that the image quality is consistent
across the screen, that aspect ratio is maintained, and that pixel phase can be optimized
(described below). Tracking determines the frequency of the pixel sampling clock, indicated
by the number of incoming pixels per line, so that all pixels generated by a particular
source are sampled.
NOTE: By default, the projector samples at the correct frequency for most sources.
For best results, use a good test pattern such as a smooth gray consisting of a clear
pattern of black and white pixels, or a similar “half on, half off” graphic image, such as
the Windows shutdown screen. Adjust the slidebar until the vertical stripes broaden to
the point where one large stripe fills the image. If the image still exhibits some shimmer or
noise, adjust Pixel Phase (below).
Pixel Phase
NOTE: Adjust “Pixel Phase” after “Pixel Tracking”.
Adjust pixel phase when the image (usually from an RGB source) still shows shimmer
or “noise” after pixel tracking is optimized. Pixel phase adjusts the phase of the pixel
sampling clock relative to the incoming signal.
For best results, use a good test pattern such as a smooth gray consisting of a clear
pattern of black and white pixels, or a similar “half on, half off” graphic image, such as
the Windows shutdown screen. Adjust the slidebar until the image stabilizes and each
pixel is clearly defined. You may notice that you can stabilize the image at more than one
point — that is, you may find that the image appearance at “11” is identical to the image
appearance at “38,” thus you can use either setting.
If some shimmer from a video or HDTV source persists, use the “Filter” control in the
Image Settings menu (described later) to remove high-frequency noise from the signal.
42
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
H-Position
This option moves the image right or left within the area of available pixels.
NOTE: The value shown represents where the approximate center of the image lies in
relation to the total number of pixels available horizontally. This varies widely according to
the signal—watch the image while adjusting.
V-Position
This option moves the image up or down within the area of available pixels.
NOTE: The value shown represents where the approximate center of the image lies in
relation to the total number of pixels available vertically. This varies widely according to
the signal—watch the image while adjusting.
Advanced Size and Position — SUBMENU
This submenu consists of the following options:
ACTIVE INPUT WINDOW: This read-only value indicates the current size (i.e., area) of
your displayed data or “region of interest” as defined by the blanking controls. By default,
the projector automatically determines what portion of its full resolution to use, and pixels
in the surrounding borders are turned off. You can also specify a specific active input
window size by adjusting one or more “Blank” settings. For example, if you have blanked
(cropped) 100 pixels from both the left and right edges of an incoming source of 1400 x
1050, the remaining active input window will be reduced to 1200 x 1050. When using SD
or HD, or a decoded video source at INPUT 3 (Composite) or INPUT 4 (S-Video), the
default blanking of “0” defines an active input window of 720 x 483.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
43
Section 3: Operation
BLANKING (TOP, BOTTOM, LEFT, and
RIGHT): Crop the image as desired so
that unwanted edges are removed from
the display (changed to black—see right).
Blanking defines the size of the Active Input
Window, or area of interest. The range of
adjustment depends on the source resolution
and other factors.
PLUG & DISPLAY (EDID): By default, a Plug & Play (EDID)
source outputs a signal according to the EDID information
provided by the projector. To override this information and
display in a different format (for example, if your Plug & Play
[EDID] device does not support the projector’s resolution and/or
frequency), select the desired Plug & Play (EDID) resolution from
the list.
Any daisy-chained projectors will also display according to the
chosen Plug & Play (EDID) format.
EDID = Extended Display Identification Data standard.
Image Settings Menu ➤
Use options in the Image
Settings menu to alter your
image without affecting its size
or position. Changes made to
the Image Settings menu are
applied immediately and are
saved when you exit the menu
(press EXIT or MENU). Options
not available for the projector
model or source are disabled
and appear dim (gray).
44
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Contrast
“Contrast” increases or decreases the perceived difference between light and dark areas
of your image (0-100). For best results, keep it under 50. If contrast is set too high, the
light parts of the image lose detail and clarity. If set too low, the light areas will not be as
bright as they could be and the overall image will be dim. For best results, start with a low
value and increase so that whites remain bright but are not distorted or tinted and that
light areas do not become white (i.e., are “crushed”).
NOTE: If the environment lighting changes, an adjustment of Gamma is recommended
(see below).
Brightness
“Brightness” increases or decreases the amount of black in the image (0-100). For
best results, keep close to 50. Start with a high value and decrease so that dark
areas do not become black (i.e., are “crushed”). Conversely, high brightness changes
black to dark gray, causing washed-out images.
Gamma
“Gamma” is a global setting that determines how gray shades are displayed between
minimum input (black) and maximum input (white) for all signals. A good gamma
setting helps to optimize blacks and whites while ensuring smooth transitions for
the “in-between” values utilized in other grays. Unlike the Brightness and Contrast
controls, the overall tone of your images can be lightened or darkened without
changing the extremes and all images will be more vibrant while still showing good
detail in dark areas when using the “Gamma” control.
The normal gamma setting of 2.2 is correct for virtually all signals and conditions.
If excess ambient light washes out the image and it becomes difficult or impossible
to see details in dark areas, lower the gamma setting to compensate. This will
improve contrast while maintaining good details for blacks. Conversely, if the image
is washed out and unnatural, with excessive detail in black areas, increase the
setting. Again, good gamma improves contrast while maintaining good details for
blacks and whites.
Filter
The proper filter setting is automatically set for virtually all signals,
and rarely needs to be changed. It applies a low pass filter for noise
reduction in the incoming input signal, particularly for HDTV or
SDTV. Applied in the analog domain before sampling, this filtering
removes high frequencies and thus reduces pixel phase noise (note this also reduces
signal bandwidth). Override only if standard pixel tracking and phase adjustments do
not adequately clear up a “noisy” video signal, or if a graphics signal appears overly
“soft”. Both instances indicate that “Filter” may be set to the wrong option.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
45
Section 3: Operation
Detail
“Detail” adjusts the sharpness of a video image so that edges remain clearly defined. It
can be particularly useful if a significant “Noise Reduction” adjustment has caused the
image to appear too soft. Adjust until the display is as sharp as desired, keeping in mind
that because “Detail” adds some high frequencies back into the image, it can also reintroduce a certain degree of noise.
Noise Reduction
“Noise Reduction” is similar to the “Filter” control, but operates in the post-sampling digital
domain with a more subtle effect. Higher settings are most useful for clearing up noisy
RGB images such as those from a PC. Adjust as desired, keeping in mind that reducing
noise (which reduces high frequencies) may also soften the image.
Color Space
“Color Space” determines how the color components of an analog
input signal are decoded for accurate color in the display. Selecting
a color space option is useful only for analog signals connected to
INPUT 1, INPUT 2, INPUT 5 or INPUT 6. Although color space for
these analog signals is automatically determined by the projector, in some circumstances
you may wish to override this and manually set a specific color space.
NOTE: For digital signals or for signals connected to INPUT 3 or INPUT 4, the color
space function is entirely automatic and the pull-down list disabled.
The current color space appears in the Image Settings menu. Press 7 (or highlight Color
Space and press Enter) to select a different option:
•
Select RGB unless you are using component video at INPUT 1, 2, 5 or 6.
•
Select YPbPr (Video) with a standard definition televised signal (SDTV)
•
Select YPbPr (HDTV) with a high definition televised signal (HDTV).
NOTE: When certain RGB signals are first connected, the projector may not initially
recognize them as RGB and will incorrectly decode their color information as YPbPr
(video). These signals, which appear magenta, can include:
•
RGB signals in NTSC, PAL, SECAM frequency ranges
•
Scan-doubled sync-on-green
•
Scan-quadrupled sync-on-green
For these signals, change the Color Space to RGB.
46
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Video Options — SUBMENU
This submenu is used with video sources only
(Input 3 or Input 4).
ENABLE DECODER AGC: Automatic Gain
Control (AGC) affects decoded video images
only. Enter a checkmark (default) in most
instances—this activates the decoder’s AGC circuit to ensure properly bright images.
Delete the checkmark if a decoded video image exhibits strange color artifacts such as
stripes in highly saturated colors, indicating an incompatibility between this source and
the AGC.
VIDEO STANDARD: For all but the more unusual video standards
available in the world, the projector automatically detects the incoming
horizontal and vertical frequencies and sets the projector’s processing
of this signal to the corresponding standard. The current video standard
name appears in the Video Options submenu, and includes an “A” if it
has been auto-detected. Press Enter to view or select a different video
standard from those available to the projector—any that are disabled
have frequency characteristics that differ from those of the incoming
signal. Selecting a specific standard forces the projector to process the
signal according to this standard.
Standard
Where Used (SUBJECT-TO-CHANGE)
NTSC
N. America and Japan
NTSC 4.43
A tape-only standard for partially-translated hybrid signals
PAL
Most of Europe, China, Australia, some of S. America, some of Africa
PAL-M
Brazil
PAL-NC
Argentina, Chile, other Latin American countries
PAL 60
SECAM
France, Eastern Europe, most of Africa
NOTE: Generally, use “Auto” for all instances EXCEPT: 1) a poor quality input signal or
2) a black-and-white video signal. In order to detect and display such signals, select the
relevant standard from the list.
INPUT VIDEO BLACK — This control
compensates for incoming elevated black levels
present in certain video signals, and ensures
that blacks in the display are neither crushed (i.e., where dark grays appear black) nor
excessively elevated (i.e., where blacks appear dark gray). By default, the projector
automatically determines the best setting according to the type of incoming video
signal:
•
0 IRE – Used for DVD output with “enhanced black”, SECAM, most PAL standards,
and Japanese NTSC.
•
7.5 IRE – Used for most NTSC video signals.
For some types of video, you can override the setting. The control is disabled for other
types of video (and all graphics sources). Generally, if black appears crushed when
brightness = 50, choose 0 IRE. If black appears excessively elevated, use 7.5 IRE.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
47
Section 3: Operation
COLOR — This slidebar adjusts the color saturation level, i.e. the amount of color in
a video image. Lower settings produce less saturated colors — for example a setting
of “0” produces a black and white image. If the color level is too high, colors will be
overpowering and unrealistic.
TINT — This slidebar adjusts the red/green color hue for true color reproduction of
video signals connected to INPUT 3 or 4. For best results, adjust tint while displaying
an external color bars test pattern—otherwise, use the default setting.
DECODER LUMA DELAY – This control affects any incoming composite or S-video
signal, delaying the luma signal (intensity) in relation to the chroma (color). In the
image, increasing the luma delay will move luma (seen as a shadow where colors
overlap) to the right slightly, with colors remaining in place. Decreasing this delay will
move the shadow slightly to the left. If necessary for your current source, adjust so
that no shadows occur with adjacent colors.
Input Levels — SUBMENU
NOTES: 1) Because the projector automatically optimizes input levels for all but the most
unusual of sources, it is recommended that only experienced users use the Input Levels
submenu. 2) Before beginning, check that overall contrast and brightness settings
are near 50 and that color temperature is properly set up on an internal grayscale test
pattern. 3) There must be at least two consecutive white pixels present in the image for
the “Auto Input Level” function to work properly. Uncheck this item before exiting this
menu.
Good RGB or input levels
— that is, the drives and
blacklevels for each of the
three colors, red, green and
blue — ensure that images
from analog sources other
than decoded video have
maximum contrast without
crushing black or white.
By default (and in an “Auto
S e t u p ” ) , t h e p ro j e c t o r
automatically determines
the best input levels by
monitoring image content and adjusting the controls appropriately; further adjustment
is typically not required to obtain proper blacks or whites.
NOTE: This automatic adjustment requires at least two consecutive white pixels in
the image. Without these pixels, input levels may produce skewed colors, particularly in
nonvideo images.
However, for a very unusual source exhibiting one or more overly high blacklevels
(typically caused by a noisy source causing blacklevel spikes), an experienced user
may prefer to use the Input Levels menu (shown above). These adjustments, which
together serve as a calibration process compensating for differences in sources and
cabling, enable an experienced user to perfect the source image input levels and
eliminate the “overshoot” and “undershoot”. Note that Input Levels are of limited
use with digital signals, but do offer some ability to tweak poorly mastered source
materials.
48
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
AUTO INPUT LEVEL – Keep off for virtually all sources (default). Temporarily enter a
checkmark only if you are an experienced user and you have an unusual source that
you feel needs further color temperature and/or input level adjustment. After entering
a checkmark, wait for the six slidebar values to stabilize, then delete the checkmark
and exit. This compensates for incoming out-of-range drives (white) and blacklevels
(black) that would cause “crushing” of light and dark colors in the image.
BLACK LEVELS AND DRIVES - To check your image and adjust these controls:
1. Make sure overall “Contrast” and “Brightness” settings are both set to near 50.
(Not required for “Auto” adjustment.)
• Contrast = 50 (approx.)
• Brightness = 50 (approx.)
2. Check the color temperature setup using an internal grayscale test pattern,
making sure to obtain a neutral grayscale. (Not required for “Auto” adjustment.)
3. Confirm that you are using an analog source not connected to INPUT 3 or
INPUT 4, as Input Levels are not applicable for digital sources or sources going
through the decoder. A grayscale is recommended.
4. If the blacks and/or whites appear OK, input levels do not need adjustment. If
black levels are too high (and/or whites are too low, which is rare), you likely have
a noisy source that is producing skewed input levels. Continue with Step 5.
5. Temporarily enable “Auto” in the Input Levels submenu. Wait for all 6 values to
stabilize. Alternatively, do not use “Auto”—reduce blacklevels manually instead.
Judge by eye and change one or more of the six levels as necessary to obtain
proper blacks and whites. You may want to see only a certain color while
adjusting; if so, use the “Color Enable” option (described below).
6. Delete the “Auto” checkmark and leave the Input Levels menu.
AUTO COLOR ENABLE – When a checkmark is present, selecting a specific
blacklevel or drive to adjust will automatically enable the corresponding color in the
display. Delete the checkmark to see all colors.
CLAMP LOCATION – This option (formerly known as sync
tip clamping) can brighten the image produced from certain
high-resolution, high-frequency graphic sources. For almost all
sources, the best clamp location is automatically selected by
the projector.
Use the normal Back Porch location if the image is either sufficiently bright or overly
bright. Select Sync Tip if the image appears unusually dim, if there are horizontal
streaks across the image, or if there is significant color drift. This moves the clamping
pulse from the normal back porch location (which is likely too short) to the tip of the
horizontal sync pulse. Tri Level is typically recommended for an HDTV source where
the back porch is also short.
NOTE: Clamp Location is not used for video sources or any RGB source with sync
information included on the video (e.g., sync-on-green). Use Tri Level instead.
COLOR ENABLE – Select which color or colors you want to see in the display, useful
while working with color temperature white levels or input levels.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
49
Section 3: Operation
NOTES: 1) Input levels apply for the current source only, but for any color temperature
used. 2) Assuming that color temperature has been set up based on the internal test
patterns, you can then set up input levels for a given source so that it matches the color
temperature of the internal test patterns.
PEAK DETECTOR – The Peak Detector is a fast method for defining individual input
levels, and can improve the accuracy of input levels set by the Auto Input level function.
Enabling the Peak Detector activates a special operating mode for detecting only pixels
that are considered black or white—all other levels are displayed as a mid-level gray.
When used with a smooth grayscale pattern in which black and white are known to
be at opposite edges of the image, you can watch these isolated areas while adjusting
individual blacklevels and input drives until both black and white edges are just visible and
distinguished from neighboring pixels. Images from this source will then display correct
blacks and whites without crushing.
See Figure 3.13. Adjusting Input Levels Using the Peak Detector:
1. Display a 16 level grayscale test pattern from the desired external source, and
enter a checkmark in the Peak Detector checkbox. NOTE: The “Peak Detector”
will initially render the grayscale as a uniform gray field before adjustment.
2. Display one primary color (use Color Enable to select).
3. For the current color, adjust its corresponding “Blacklevel” slidebar just until a
single band of black appears at one edge of the screen. This band represents the
first band of the grayscale pattern, which should be 100% black. Do not adjust
too far.
4. With the same color still active, adjust its corresponding “Input Drive” slidebar just
until a single band of color appears at the opposite edge of the screen. This band
represents the last band of the grayscale pattern, which should be 100% white
(or the current color, if a certain color is enabled). Do not adjust too far.
5. Go back and check the black band—adjust the blacklevel slidebar if necessary.
Blacklevel and Input Drive adjustments are related, so you may have to go back
and forth until both bands are just optimized.
6. Repeat Steps 2-5 with the other two remaining primary colors. When each
primary color shows one optimized black band and white (or colored) band, the
input levels for this source are correctly set. Upon exiting the Input Levels menu,
the Peak Detector checkbox will clear.
50
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Figure 3.13. Adjusting Input Levels Using the Peak Detector (RED EXAMPLE SHOWN)
Advanced Image Settings —
SUBMENU
GAMMA TABLE: This control selects
and applies the normal 2.2 gamma
setting or a user-defined “arbitrary”
(custom) gamma table that has been
previously downloaded to projector
memory (these custom gamma
tables—a.k.a. curves—are created in
Runco’s Arbitrary Gamma application
for the PC, and are downloaded via a
separate utility). Use of custom curves
can improve performance for certain
kinds of source input and applications.
Generally the best gamma curve is
one that produces maximum contrast, brightness and color performance for the current
signal and ambient lighting conditions.
NOTE: If no such curves have been defined and downloaded to projector memory, only
the “2.2, Normal” default gamma curve is available here—adjust as desired in the main
Image Settings menu.
SELECT COLOR ADJUSTMENT: In “Select Color
����������������
Adjustment”, choose an overall color performance for all
����������������������
images. The “Max Drives” factory default simply drives all
�������������
3 colors at their maximum level so that they are fully on
�������������
and cannot be changed. The two other pre-defined color
������������
��������������
adjustment choices—SD Video and HD Video—apply a
�����������
color gamut optimized for video sources (standard or high�����������
definition). Alternatively, you can specify a color temperature,
which enables the nearby Color Temperature slidebar and
applies its current setting (default = 6500K). If none of the pre-defined “Select Color
Adjustment” options or color temperatures suit your application, select one of four
color gamuts previously defined by a user (ISF Day, ISF Night, 3, 4). A “User” option
applies a customized color performance in which the user has precisely set the
hue and intensity of each color component in the Color Adjustment by X/Y or Color
Saturation submenus, and is most often needed with multiple-projector applications.
Select the color adjustment producing the best color accuracy for your application
and installation.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
51
Section 3: Operation
To configure a “User” color adjustment (gamut), use either the Color Adjustment by
X/Y or Color Saturation submenu found in the Configuration menu under Geometry
and Color.
NOTES: 1) “Color Temperature” defaults to 6500K until changed. Both “User” options
default to SD Video unless they have been redefined by the user. 2) Factory defined
color primaries, which ensure consistent color gamut from projector-to-projector, can
be altered in the Service menu only. If you suspect alteration, the factory settings can be
recovered with selection of Factory Defaults in the Service menu (password-protected).
COLOR TEMPERATURE — Adjust to apply a specific and accurate color temperature
to all displays. Color temperatures are expressed in kelvins (3200-9300K), and utilize
different combinations of the projector’s original native color primaries to produce
a “coloration” or cast (reddish or bluish) in images—the lower the temperature, the
more reddish the cast; the higher the temperature, the more bluish the cast. Note
that the slidebar is enabled only if you have a source connected and have selected
“Color Temperature” in the adjacent “Select Color Adjustment” pull-down list in the
Advanced Image Settings menu.
FRAME DELAY — Set the interval of delay desired between the input signal and
its appearance on screen. For applications such as simulation, where the feeling of
“real time” image response is a priority, a minimum setting is usually preferable. For
projectors capable of 3D (stereographic) applications where alternating left-right
frames must be synchronized with the corresponding L/R shutters in 3D glasses, a
frame delay setting of two (or multiple of two) may be more useful. Delay may vary
between sources.
MOTION FILTER — This control is most useful for smoothing out
moving images from interlaced sources. In most cases the proper
Motion Filter setting is automatically determined according to the type of
incoming source signal. However, if your source is jittery and/or tearing
you may wish to “force” a setting to ensure stable processing for this
source—if desired, override the default “Auto” setting by selecting the appropriate
motion filter:
1. AUTO: The projector will automatically use the correct motion filter according
to the incoming signal.
2. STILL: For static images with no motion, such as graphics from a CD.
3. MOTION: For video images that did not originate from film, or for moving
computer-generated images.
4. FILM: For video images that originated from film. This will optimize image
quality and stability.
FILM MODE THRESHOLD — This setting determines how sensitively the projector
can detect if an incoming video signal originated from film or not.
DETAIL THRESHOLD — Use “Detail Threshold” to define at what frequency level the
“Detail” control will begin to magnify high frequencies, which adds details back into
the image. Raise the threshold to ignore more of these high frequencies, and lower
the threshold to magnify more of these frequencies. A setting of “0”, for example,
means no noise will be ignored and all will be magnified. An ideal detail threshold is
one in which high frequencies that are causing objectionable noise are not magnified
when using “Detail”, but frequencies which can help sharpen an overly-soft image
are magnified when using “Detail”.
52
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Use the Configuration menu to
define general operating parameters
and communications with other
projectors and equipment, and to
access other advanced processing
and image adjustments affecting
overall performance. In addition, the
Configuration menu provides access
to diagnostic and calibration tools,
as well as the Service submenu
(password protected).
3.6 Adjusting System
Parameters and
Advanced Controls
Keep in mind that settings in the Configuration menu (and its submenus) are typically
“global” settings applied regardless of the type of source your are using. This
characteristic is identified with the (globe) icon alongside the option. NOTE: The
Configuration menu is recommended for experienced users/technicians only.
➤
The first six options in the Configuration menu are explained below:
System Configuration
— GENERAL —
Language
Choose from available languages to use in the projector’s menus. The change will take
effect immediately.
Image Orientation
Set the orientation of the image according to the orientation of your projector. If the
setting is incorrect, projected images will be reversed and/or upside down.
Fade Time
Set how long (in seconds) it takes to gradually dissolve one image into another for a
source switch.
Auto Power-up
Enter a checkmark to enable the projector to automatically power up after losing power
due to a power failure or due to unplugging the projector during operation. Runco
recommends that this be left unchecked, as a power loss in an unattended house will
result in the projector turning on without anyone realizing it is on.
Note that unsaved display adjustments may be lost.
Set Date and Time
Enter/read the current year-month-day and hour-minute-second. Changes here reset the
projector’s real-time clock.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
53
Section 3: Operation
Menu Preferences —
SUBMENU
Use the options in this submenu
to adjust the appearance, content
and/or location of on-screen menus
and messages.
LARGE MENU FONT — Enter a
checkmark to enlarge menus and
their text. You may have to adjust “Menu Location” to accommodate the increased menu
area.
MENU LOCATION — Use the pull-down list to choose a pre-defined default or customized
location for the display of all on-screen menus.
To create a custom menu location quickly, choose a preset that is closest to the desired
location. Then adjust “Horizontal Shift” and “Vertical Shift” slidebars to move the menu to
the desired location. Avoid locations too close to a corner or edge to prevent cropping of
larger menus.
HORIZONTAL SHIFT AND VERTICAL SHIFT — Shift your menus as desired, creating
a customized menu location.
DISPLAY CHANNEL LIST — Enter a checkmark if you want to see a scrollable channel
list whenever you press Channel (CHANL) from your presentation. Channels marked with
a list icon in the Channel Setup menu will appear here. The “Display Channel List” option
also enables on-screen feedback when using the Input key. If you prefer to hide the channel
list and input dialog box while switching channels and sources during a presentation, clear
the checkbox.
NOTE: The Channel List and input dialog box cannot be hidden during use of the
menus.
DISPLAY SLIDEBARS — This setting is not applicable to this projector/remote
combination.
DISPLAY ERROR MESSAGES — Choose in what way you want to be notified of errors
detected in either the incoming signal or projector. Select “Screen” or “All” to see a brief
on-screen message or select “RS232” to receive messages via RS232 (or RS422) serial
communication only. Select “Off” to hide error message displays. Because the DHD
Controller uses the RS232 port, Runco recommends this be set to Screen.
54
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Figure 3.14. Communications
Baud Rates
The baud rate setting determines the speed of communication to and from the
projector on the RS232 or RS422 links. The maximum rate for either standard is
115200. The default baud rate for use with the DHD Controller is 115200. If this is
changed, communication with the DHD Controller will be lost.
Projector
Enter a three-digit number (such as “001”) to assign or change a number to the
projector currently in use. If the current projector already has a number assigned,
that number will appear here (for example, “004” in Figure 3.14, above). Numerical
identity for projectors enables you to communicate with a single projector within a
multiple-projector application. If you make a mistake in assigning or changing the
projector number, press Exit to cancel.
NOTE: This feature is not used when the projector is used with the DHD Controller.
Network Routing
NOTE: This feature is not applicable when the projector is used by itself, with the DHD
Controller or in a simple serial network with only one type of controller and linking.
SEPARATE: Select “Separate” (factory default) to keep RS232, RS422 and Ethernet
messages on their respective paths instead of being broadcast to the other types
of ports.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
55
➤
Settings in the Communications submenu define and control how single or multiple
projectors are can link with each other and with a controlling device.
System Configuration
— COMMUNICATIONS —
Section 3: Operation
Ethernet Settings (SUBMENU)
This menu is reserved for future use.
Backlight
Toggle the built-in keypad lighting on/off.
Front IR / Back IR
As needed for your application, set to “on” so that the front and/or rear IR sensor
locations on the projector responds to the IR keypad. Set to “off” to disable.
To disable both IR sensors, you cannot use the IR remote keypad to select the second
OFF setting. This safeguard prevents accidentally disabling an IR keypad while you
are using it. Instead, use either the built-in keypad or a wired remote (optional) to
set the remaining active sensor to OFF. The projector will no longer respond to an
IR remote keypad.
Wired Keypad
Select “On” to enable use of a wired remote keypad connected to the rear of the
projector. The projector will then respond to incoming commands from either port.
To disable the wired keypad, you must use a different keypad—the built-in or an IR
remote keypad—to select “off”. This safeguard prevents you from accidentally disabling
the wired keypad during use.
56
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
In the Configuration menu, select
the Geometry and Color submenu
when you need to modify overall
color performance and/or image
geometry for all sources.
➤
Test Pattern
Choose the desired internal test pattern or select OFF to turn off a test pattern.
Alternatively, use the TESTP key for cycling through test patterns.
Vertical Keystone
Use to correct a keystoned image shape in which both sides of your image are
inclined toward the top or bottom edge. Keystone is typically caused by tilting the
projector in relation to the screen, so that the lens surface and screen are no longer
parallel to each other.
Figure 3.15. Keystone Adjustment
NOTE: Runco recommends that the keystone feature not be used unless absolutely
necessary, as it may cause some artifacting in the image.
Brightness Uniformity — SUBMENU
Brightness Uniformity provides further refinement of displays already matched for
their primary colors and overall light output. Use Brightness Uniformity to create an
exceptionally smooth image in which no area appears brighter and/or more red, green
or blue than another. In the Brightness Uniformity menu, check the “Uniformity Enable”
checkbox to access a multitude of adjustments for critical color light output control
in specific areas throughout the image. Your settings apply as long as the “Uniformity
Enable” checkbox is enabled and you are using a “User” color temperature defined
by the Brightness Uniformity controls. Remove the checkmark from the “Uniformity
Enable” checkbox to disable the Brightness Uniformity function.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
57
Geometry And Color
Section 3: Operation
Edge Blending — SUBMENU
The Edge Blending submenu provides a range of controls for smoothing together
the overlapping bright edges of multiple adjacent projected images to create a single
larger “seamless” image.
Color Adjustments by X/Y, and Color Saturation — SUBMENUS
NOTES: 1) For defining or changing a User 1, 2, 3, or 4 color performance or “gamut”.
Sometimes known as Comprehensive Color Adjustment™. 2) Factory-measured
primary color levels, which ensure a specific color performance from projector-toprojector, can be altered in the Service menu only. If you suspect alteration of these
defaults, the factory settings can be recovered with selection of “ Factory Defaults”
in the Color Primary Settings submenu accessed via the Service menu (passwordprotected).
From the factory, the projector can utilize any
of the three pre-defined color performance
settings identified at right (default=Max
Drives) or colors can be driven on the basis
of color temperature. For most applications,
one of these options will produce accurate
and realistic colors from a variety of sources.
They can be applied at any time in the
Advanced Image Settings menu (“Select
Color Adjustment”) and are not adjustable.
DEFINING “USER” COLOR GAMUTS: In some cases, you may find that none of the
predefined “Select Color Adjustment” options exactly suit your needs. For example,
you may require a unique color gamut (range) for a single projector or application, or
you may need to precisely match colors across multiple adjacent displays. In such
cases, use either the Color Adjustments by X,Y or Color Saturation submenu to define
the precise hue of each primary color component (red, green, blue, and white) used
to generate the millions of colors produced in displays. You can create up to four
custom color gamuts (User 1, 2, 3, or 4) defined by these adjustments.
Note that the two menus differ only in their user interface, so use whichever menu best
suits your needs and application.
•
Color Adjustments by X,Y — Enter known x/y coordinates from the chromaticity
graph. For best results, use with a color meter.
•
Color Saturation — Adjust color slidebars and judge image color by eye. A color
meter can also be used.
A user-defined color “adjustment” can be applied by selecting it in the Advanced
Image Settings menu (“Select Color Adjustment”).
NOTE: Defining a “User” color gamut when a test pattern is displayed does not get
saved in the current channel. Display the source first, then select a color gamut (User)
from Select Color Adjustment. Changes here are then saved for that source in channel
memory.
58
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
COLOR ADJUSTMENT BY X,Y:
Use this submenu if you want to
alter, add or copy a color gamut
(i.e., “color adjustment”). Controls
in this menu define the precise hue
of each primary color component
(red, green, blue, and white) used
to generate the millions of colors
produced in displays. The x/y
coordinates for each color define
its location on the standard CIE
chromaticity graph (see Figure
3.16)—changing either or both
of these numbers will change the
hue of the color, and relocate the
“triangle” for possible colors. For example, changing the x/y coordinates for red will
either move the color closer to orange or closer to violet, which will in turn affect all
displayed colors having a red component. Adjust the slidebars or enter new specific
coordinates as desired to define or change up to four “User” color gamuts needed
for your environment and applications. Apply the new “User” color gamuts at any
time in the Advanced Image Settings menu.
Figure 3.16. CIE 1931 Chromaticity Diagram
NOTE: Keep new x,y coordinates within the original color gamut triangle shown here.
Refer to Section 6, Specifications, for color primaries.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
59
Section 3: Operation
COLOR SATURATION: Use this
submenu if you do not have specific
color coordinates in mind and will
simply judge color performance
by eye (or meter). Like the Color
Adjustment by X,Y submenu, each
color control actually defines new
x/y coordinates for that color and
changes its hue — it is just a different
interface.
Adjust the hue of each primary color
(red, green, blue, and white) by using
more or less of it in relation to the
other colors.
Figure 3.17. Customize Color
NOTE: A Color Saturation adjustment sets the corresponding x/y coordinates shown
in the Color Adjustment by X,Y submenu. These x/y coordinates will remain stable for
this User gamut until they are changed again via either menu. Values displayed in the
Color Saturation menu, however, will likely fluctuate as you use the projector, and will
be different when you return to this menu at some point in the future. These floating
changes do not affect the x/y coordinates or gamut.
Diagnostics and Calibration ➤
Test Pattern
Choose the desired internal test
pattern to display or select OFF to
turn off a test pattern. Alternatively,
use the TESTP button on the
remote control for cycling through
test patterns.
NOTE: Runco recommends that all
calibration parameters (grey scale,
sizing, etc.) be done with external
test patterns.
Test Pattern Grey Level
Set the desired level of grey for displaying in the full gray field test pattern.
Freeze Image
Enter a check mark to freeze (stop) an image on a single frame. This diagnostic tool is
useful if you need to examine in detail a still version of an incoming image that cannot
be “frozen” at the source. For example, in moving images it is sometimes difficult to
observe artifacts such as external deinterlacing/resizing and signal noise. Remove
the checkmark to return back to normal.
60
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Color Enable
Select which color or colors you want to see. This is useful while working with color
temperature, input levels or other special setup parameters.
Odd Pixel Adjustment
NOTES: Factory-set and rarely required by user.
When using certain RGB sources, you may need to adjust the normal gain or offset
of odd pixels in relation to even pixels. This will smooth out very narrow (1-pixel wide)
“checks” or vertical stripes that indicate adjacent “on” and “off” pixels. Although offset
and gain slidebars can be adjusted individually and manually, using the Level Detector
simplifies this process (see Figure 3.21):
1. Use an external analog native-sized continuous grayscale test pattern with at
least 256-levels.
2. Turn “Level Detector” on.
3. Set “Level Value” to ~200. The image should now be black-and-white (or blackand-one color, if you use “Color Enable” function).
4. Adjust offset. Half of the pixels will move, the other half will not.
5. Adjust until the two transition regions overlap. The stripe of noise will be minimized,
defined by the value in the slidebar.
6. Set “Level Value” to ~800. The image should now be black-and-white.
7. Repeat Steps 4 and 5, but adjusting gain.
8. Repeat Steps 3-7 for all remaining colors. Your RGB source should now be
OK.
Figure 3.18. Using Odd Pixel Adjustment
NOTES: 1) Adjust offset before gain, since offset affects gain. 2) A value of 128
represents no change in normal odd pixel offset or gain. 3) Odd Pixel Adjustment
eliminates “1 pixel on, 1 pixel off” patterns only, not any type of larger patterns.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
61
Section 3: Operation
Reserved
No function.
Peak Detector
The “Peak Detector” is fast method of defining individual input levels, and can improve
the accuracy of input levels set by the Auto Input Level function. Enabling the “Peak
Detector” activates a special operating mode for detecting only pixels that are
considered black or white — all other levels are displayed as a mid-level gray. When
used with a 16-step grayscale pattern in which the two black and white bands are
known to be at opposite edges of the image, you can watch these isolated areas
while adjusting individual blacklevels and input drives until both bands are just visible.
Images from this source will then display correct blacks and whites without crushing
or washing out.
Level Detector
The “Level Detector” checkbox enables specific thresholds for blacks and whites — input
levels that fall below a specified Level Value (see below) are displayed as black, and
all others are displayed as white. It aids in Odd Pixel Adjustment. To use:
1. Enable “Level Detector” and display a continuous grayscale.
2. Set “Level Value” to near black (such as 200).
3. Adjust Offsets to minimize area of black stripe.
4. Set “Level Value” to near white (such as 800).
5. Adjust Gains to minimize area of white stripe.
Level Value
The “Level Value” defines the value to be used by the Level Detector in recognizing
blacks and whites. Refer to Level Detector, above.
3.7 Working with the
Lamp
Whenever you install a new lamp in the
projector, access the Lamp menu to record
the lamp serial number in the projector’s
memory. You can also choose a lamp mode
for regulating power and light output, change
optical aperture size, and access other readonly information pertaining to past and present
lamps.
LAMP HOURS shows the number of hours logged on the current lamp. Whenever you
record a new lamp serial number this value automatically resets to “0”, where it begins to
log time for the new lamp.
NOTE: Read-only. This information also appears in the Status menu.
LAMP S/N is the serial number recorded for the current lamp. When you install a new
lamp and enter its serial number, the number will appear here. NOTE: Read-only.
62
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Enter a checkmark for LAMP MESSAGE to enable a warning message that will appear
upon power-up when the lamp has reached the specified lamp limit and should be
replaced. Delete the checkmark to prevent display of this message—instead, when your
lamp expires, only the status display messages on the back of the projector will provide
the visual warning to replace the lamp.
NOTES: 1) It is recommended that the Lamp Message checkbox remain enabled.
2) When a lamp warning message appears, press Exit to temporarily cancel the
message. The message will continue to appear upon power-up until you install a new
lamp.
Set LAMP LIMIT to the number of hours you expect to log on the current lamp before
replacing it. This will trigger a lamp message on-screen (if enabled).
NOTES: 1) If you change modes over the life of a lamp, the lamp limit you originally
expected may no longer be possible. 2) Turning the lamp on and off reduces lamp life
significantly, as do other factors. 3) It is recommended that Lamp Limit not exceed the
expected lamp life, otherwise a lamp could become dangerously fragile with overuse.
Set which LAMP MODE you want to use in order to control the
light output. You can choose to run the lamp as bright as possible
(i.e., always using maximum power—this is the default upon
power up) or you can power the lamp with a specific wattage
appropriate for the installed lamp or you can set a specific
intensity (brightness) to maintain. Although there are exceptions,
generally higher light output or higher power settings can shorten
lamp life.
Figure 3.19. Lamp Mode
Use the lamp mode that best suits your brightness needs. For example, in a tiled application
you may want to precisely match brightness levels between adjacent images—judge by
eye and set each individual Lamp Power setting as necessary. Or if you want images
to be as bright as possible—choose Max Brightness. Always keep in mind that higher
lamp power settings can shorten lamp life.
Lamp modes are described below:
•
Max Brightness: The lamp will always burn as brightly as possible, driven by
100% of the power level rating for the installed lamp (see Section 6, Specifications).
Keep in mind that the “maximum brightness” for any lamp gradually diminishes
with age — images will become dimmer over time. Its current output level appears
in the “Intensity” option (note: not in lumens).
•
Intensity: Brightness will remain close to a specified level for as long as possible.
Once you select this option, enter a number representing the intensity level
(brightness) you wish to maintain—the projector will automatically adjust power
as needed to maintain this intensity as closely as possible. Note that the intensity
value is a correlation only and does not represent an actual lumens level. See
“Intensity” on the next page.
•
Power: The power supplied to the lamp will remain at your specified wattage
level. Once you select this option, enter the number of watts representing the
power level you wish to maintain. See “Power” on the next page.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
63
Section 3: Operation
POWER – This slidebar and number indicates how many
watts are applied to the lamp. You can apply anywhere
from approximately 60-65% of the maximum power intended for the installed lamp up to
100% of the lamp rating. Set for the number of watts as desired, keeping in mind that
lower power levels produce dimmer images. When in either Power or Max Brightness
modes, the power level remains constant. Specifying a maximum power level here is the
same as operating in Max Brightness mode.
NOTES: Power level can be set only if the lamp is in Power mode.
INTENSITY – This value and slidebar represents the
current brightness of your lamp, decreasing over time
when you are operating in Max Brightness mode or at a specific Power level. When
you are operating in “Intensity” mode this value remains at the original “Intensity” setting
chosen and cannot be adjusted.
NOTE: The number shown for “intensity” is not the actual lumen output, but rather a
correlated value only—1246 may represent 3500 lumens, for example.
To use “Intensity” mode, judge by eye (or use a meter) and set the level as desired for
your application. Over time, the projector will automatically increase the power supplied to
the lamp as needed to maintain the chosen intensity as closely as possible.
HOW LONG CAN I MAINTAIN BRIGHTNESS? Software can maintain your “Intensity”
setting until the required power reaches the maximum rating for the lamp. The lower the
setting, the longer it will take to reach this threshold and the longer you can maintain
the desired brightness. Keep in mind that once the lamp power reaches its maximum
wattage (see “Power”, above), this tracking is no longer possible. At this point, the lamp
will gradually begin to dim as usual, even though your original “Intensity” value will still
appear in the menu. To resume accurate tracking, reduce the intensity setting so that the
resulting “Power” value is less than its maximum—the lower the intensity, the longer it
can be maintained.
For example, a 1000 watt lamp can be driven at no more than 1000 watts. To produce
desired brightness at the screen, a new lamp would likely need less than this maximum
rating — perhaps 812 watts (example only). Over time, however, the lamp will require more
and more current in order to generate the desired light, until eventually the lamp wattage
reaches its 1000-watt maximum and the lamp power automatically levels off. At this point,
the tracking function terminates (i.e., the power level stabilizes) and the lamp will begin to
dim normally. Either reduce your “Intensity” setting or replace the lamp.
Do not lower the “Intensity” so much that the corresponding “Power” value reaches
its minimum—the intensity setting will be inaccurate and cannot be maintained. For best
results in achieving uniform intensity amongst tiled images, choose an “Intensity” setting
that enables all lamps to operate at less than the maximum number of watts available in
your projector but high enough to keep the corresponding lamp power above its minimum.
See “Power”, above.
NOTES: 1) Lamps become more stable over time, thus a specific intensity is more easily
maintained as the lamp ages. 2) Intensity can be set only if the lamp is in “Intensity” mode
3) Intensity cannot exceed the output of Max Brightness mode.
64
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
OPTICAL APERTURE – The optical aperture
inside the projector controls the diameter of the
light beam passing through the system. With a
fully open aperture (slidebar default of “0”), the
maximum amount of light passes through for
maximum brightness in your images. Increase the slidebar setting to reduce the aperture
diameter and maximize contrast ratio instead.
LAMP HISTORY – This read-only option lists the lamps most recently installed and
recorded in the projector. Lamp History automatically updates whenever
you record a new lamp serial number—the new lamp is added to the
bottom of the list.
Use CHANGE LAMP to record the serial number for a newly installed lamp:
In the Lamp S/N window, use the number text entry keys to record the new lamp serial
number and press Enter again to accept the change. See Using Slidebars and Other
Controls if you need help entering the number. Once entered, the new lamp serial number
will be added to the Lamp History menu and the Lamp Hours timer will reset to “0”. Lamp
Mode and Lamp Limit remain as they were for the previous lamp and can be changed
at any time.
Figure 3.20. Recording the New Lamp Serial Number
NOTE: Enter a serial number only if you have just installed a new lamp. This will help
ensure that lamp timer is not reset on an old lamp and that the number of hours logged
on the lamp will be accurate.
IMPORTANT
Always record the serial number of a NEW lamp.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
65
Section 3: Operation
How Old is My Lamp? ➤
When a new lamp is installed and its serial
number recorded by selecting “Change
Lamp” in the Lamp menu, the lamp timer
resets to “0” and begins logging time for
the new lamp. This tally appears in both
the Lamp menu (see right) and the Status
menu.
To review the number of hours logged for
previous lamps, consult the Lamp History
menu.
When to Replace ➤
the Lamp
If the “Lamp Message” checkbox has been enabled in the Lamp menu (recommended),
an expiry message will appear upon power-up when the lamp has reached its defined
“Lamp Limit”. The lamp should be replaced.
The “Lamp Limit” setting should not exceed the expected lamp life, as an old lamp
becomes increasingly fragile and more prone to sudden failure. See also 4.4, Lamp
Replacement.
3.8 Status Menu
The read-only Status menu lists a variety of details about the standard and optional
components currently detected in the projector. Refer to the Status menu for versions
of hardware and software installed, the type (size) of lamp, the hours logged in total and
for a specific period (such as a rental period), and for your projector model name and
serial number. In addition, the Status menu identifies the current channel, its location, its
frequencies and other details.
Scroll the full Status menu using ▲ and ▼ on the directional keypad. Use ◄ and ►
for page up/down.
66
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Occasionally the projector will encounter an error condition that can interrupt normal
operation. Such a condition can be caused by a simple invalid keypad entry, an input
signal error (most common) or a system error. The manner in which users are to be
notified of error conditions is set in the Menu Preferences menu:
•
To see error messages displayed on-screen, select the “Screen” or “All” option.
(recommended by Runco)
•
To be notified via a serial communication only, select the “RS232” option.
•
To receive both types of notifications, select “All”.
•
To disable error messages (except for “invalid user key entry”, which can’t be
hidden), select “Off”.
3.9 Error Conditions
Note that a two-digit error code appears in the status LED display window located
beside the built-in keypad at the rear of the projector. Normal operation is indicated
by the “On”status code.
LED status
display window
➤
User Errors
➤
Invalid User Entry
A keypad entry not recognized by the projector triggers a short on-screen error message
identifying the problem. For example, if you specify a channel number that is not available,
the message “Invalid Channel” will appear. Or if you try to enter the wrong password,
you’ll see “Invalid Password”. Press Enter or Exit to clear the message and try again.
Input Signal Errors
NOTE: On-screen display of “Invalid User Entry” messages cannot be disabled, even if
Display Error Messages has been set to “Off”.
An input signal error message occurs if you are in presentation level (i.e., there are no
menus present) and have selected an input on which the projector detects a problem.
While menus remain operational and any key press will temporarily remove any displayed
error message, you must resolve the signal problem in order to permanently eliminate
the message.
No Signal
The message “No signal” occurs when there is no source signal detected at the selected
input—both HSYNC and VSYNC are inactive and the screen background is black.
Connect or correct the signal, or try another input.
Bad Sync
The message “Bad Sync” occurs when HSYNC or VSYNC are active but the signal
cannot be displayed. Such a condition occurs when only one of the two sync signals
is present or when either sync signal is unstable or of the wrong frequency. Correct the
signal or select another input.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
67
Section 3: Operation
Other Signal Error Messages
In addition to the common “Bad Sync” and “No Signal” errors, you may encounter a
signal error message indicating that HSYNC and/or VSYNC are either too fast or too
slow. When such a message appears, check the frequencies shown in the Status
menu. If they are correct, then the signal is not recognized by the projector. On some
PCs you may be able to change the settings to generate a compatible signal. If the
frequencies shown in the Status menu are incorrect, check the cabling to see where
the problem might originate.
When the projector encounters a system malfunction, either a System Warning message
or a System Error message may appear. Both types of messages are accompanied
by a numerical error code on the status LED display. A system malfunction can be
cleared with Exit from presentation level, but may indicate the need for service by a
qualified service technician.
NOTE: System messages appear on-screen only if Display Error Messages has been set
to “Screen” or “All”.
System Warnings
A system warning indicates that a system malfunction has been detected (see Status
LED Codes, below). A system warning message replaces any input signal message
and disappears when the input signal status changes. While the projector will remain
operational, the message indicates the presence of a potentially serious problem
that should be investigated. You can press Exit to remove the message, but for best
results you should reset the projector—power the projector down and up again with
the (power) key.
System Errors
A system error message indicates that a serious malfunction has been detected
and must be investigated as soon as possible (see Status LED Codes, below). The
projector will no longer operate and must be reset—power the projector down and
up again with the (power) key.
The Status LED Codes
If the status code display on the back of the projector shows one of the following
values, you have encountered a likely system error requiring the attention of a qualified
service technician (see System Warnings and System Errors, above). Acknowledge
and clear the error with Exit from presentation level, or try resetting the projector by
powering it off and on again, cooling when necessary. Refer to Table 3.3 and contact
your dealer if the problem persists.
The specific code number identifies the source of the error detected, and is particularly
useful in cases where the projector is far away. For example, the code “27” means
the lamp could not be turned on. Table 3.3 lists the error codes for this projector.
68
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 3: Operation
Code
Description
GENERAL
12
Software bug. Contact dealer/factory.
13
CRC error in flash ROM. Download new software.
14
Engineering-only programming is complete. Call Runco, replace TIPM.
15
Attempting to download code without being in boot mode
16
Invalid interrupt. Power off/on. If it persists, contact dealer/factory.
17
User forced system to stay in boot mode
18
Jumper for programming boot not installed
LAMP FAILURES
20
Lamp turned on unexpectedly (fault related to ballast)
21
Lamp airflow low, overheating imminent
23
Cannot read valid ballast ID
26
Lamp 1 Interlock: lamp door open, lamp not installed
27
Can’t turn lamp on
28
Lamp turned off unexpectedly
29
Lamp ballast overheated
POWER AND COOLING
46
Red DMD temperature probe overheated
4C
Projector shutdown due to critical error
C0
Lamp blower failure (lamp not turned on)
51
LVPS fan failed (Fan 1)
52
LVPS/ Red cooling fan failed (Fan 2)
53
DC lamp fan failed in 500W / 1kW models (Fan 3)
54
Red DMD heatsink fan failed on 1kW and 1.2kW models (Fan 4)
55
Green DMD heatsink fan failed on 1kW and 1.2kW models (Fan 5)
56
Blue DMD heatsink fan failed on 1kW and 1.2kW models (Fan 6)
57
TIPM fan failed (Fan 7)
58
TIPM fan failed (Fan 8)
TIPM (Image Processor)
60
Boot code CRC failed
61
Unable to program DigMux PLD
62
Unable to program Control PLD
63
Unable to program Bubks PLD
64
Unrecognized ROM type
65
Write to flash ROM failed
66
TIPM failure
67
Downloaded code will not fit
68
Scaler communication problem
BUILT-IN KEYPAD
70
Unable to access EEPROM on the built-in keypad
71
EEPROM memory re-initialization on the built-in keypad
PANEL DRIVER AND FORMATTER
80
Unrecognized Panel Driver
81
Unable to program device on Panel Driver
82
TI flash download failure
83
TI flash download failure
84
TI flash download failure
85
TI-I2C write failure
86
One or more Formatters not responding — Probable Formatter s/w fault
87
Formatter reports RDRAM failure
88
Red modular Formatter communication failure
89
Green modular Formatter communication failure
8A
Blue modular Formatter communication failure
93
Modular formatter architecture error
94
Modular formatter DMD mismatch
95
Modular formatter sequence mismatch
MISCELLANEOUS
A0
Unable to program the optional module
A1
Unable to power the optional module
A2
Unable to program the Dual Slot Backplane Module (DSBP)
A3
Unable to program the optional Post Processing Module (Warp module)
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
69
Table 3.3 Error Codes
Clear system errors with ‘Exit Exit’. If
necessary, try resetting the projector
by powering it off and on again
(cooling if necessary). Contact
dealer/factory if error persists. Codes
omitted from this table should not
appear in your projector.
Section 3: Operation
This page is intentionally left blank.
70
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
SECTION 4
Maintenance
The projector is an international regulatory agency approved product designed for
safe and reliable operation. To assure complete safety at all times it is important to
acknowledge the following precautions while operating the projector.
4.1 Warnings and
Safety Guidelines
WARNING
Always remove the lens when shipping the projector.
WARNING
NEVER look directly into the projector lens.
The high brightness of this projector
could cause permanent eye damage.
WARNING
For protection from ultraviolet radiation, keep all projector shielding
intact during operation.
Installer
DEPENDENT
Installation should be performed by qualified personnel.
Observe and follow all warnings and instructions marked on the projector.
➤
Labels and Markings
Read all operating instructions prior to using the projector.
➤
Instructions
Operate the projector in an environment that meets the operating range specified in
Section 6 – Specifications.
➤
Projector Location
The exclamation point within the equilateral triangle alerts the user to important operating
and maintenance (servicing) instructions in the literature accompanying the projector.
The lightning flash and arrowhead symbol within the equilateral triangle alerts the user to
uninsulated “dangerous voltage” within the projector’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
• Do not operate the projector close to water, such as near a swimming pool. Do
not operate in extremely humid environments.
• Do not place the projector on an unstable cart, stand or table. A projector and
cart combination should be used with care. Sudden stops, excessive force and
uneven surfaces may cause the projector and cart combination to overturn.
• Only use Runco-approved ceiling mount fixture, if the projector is to be ceiling
mounted.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
71
Section 4: Maintenance
Lamp: The projector uses a Cermax® Xenon lamp to deliver its high brightness. A lamp
should be replaced when it has reached its end of life (1000 hrs, typical) or if a noticeable
change in brightness or excessive lamp flicker occurs. Keep track of the number of hours
the lamp has been in use (Lamp Menu) and be aware of any changes to brightness. These
indicators will help you effectively maintain operation of the projector.
WARNING
Wait approximately 5 minutes after powering down
the projector to allow internal cooling fans to stop and for
the lamp to cool sufficiently before removing.
The lamp is under great pressure when hot and may explode causing
physical injury and/or property damage. Allow a lamp to cool before
handling or unplugging the projector.
WARNING
Use lamps of the correct wattage for your projector model
when replacing.
Use only lamps supplied by Runco.
Refer to 4.4 Lamp Replacement for instructions.
Use only the attachments and/or accessories recommended by Runco. Use of others
may result in the risk of fire, shock or personal injury.
WARNING
Use only the AC power cord supplied. Do not attempt operation if the AC
supply is not within the specified voltage and power range.
Refer to the Specifications in Section 6.
•
Do not set or rest items on the power cord. Place the projector in an area where
the projector cord cannot be abused or damaged by persons walking on it or by
objects rolling over it.
•
Operate the projector at the specified voltage only. Do not overload power outlets
and extension cords as this can result in fire or shock hazards.
•
The projector is equipped with a three-wire plug having a third grounding pin. This
is a safety feature – if you are unable to insert the plug into an outlet contact an
electrician to have the outlet replaced. Do not defeat the safety purpose of this
grounding-type plug.
72
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 4: Maintenance
Do not place the projector over a radiator or heat register. The projector should
not be placed in an enclosure unless proper ventilation is provided.
•
Do not insert objects into the ventilation openings of the projector. They may
touch dangerous voltages or short-out components resulting in a fire or shock
hazard. Do not spill liquids of any kind into the projector. Should an accidental
spill occur, immediately unplug the projector and have it serviced by a qualified
service technician.
If any of the following conditions exist, immediately unplug the projector from the power
outlet and ask a qualified service technician to look at it.
•
The power cord has been damaged.
•
The internal cooling fans do not turn on within two minutes when the projector
is first powered up.
•
Liquid has been spilled into the projector.
•
The projector has been exposed to excessive moisture.
•
The projector is not operating normally or its performance has significantly
deteriorated in a short period of time.
•
The projector has been dropped or the shipping case (if applicable) has been
badly damaged.
WARNING
Do not attempt to service the projector yourself. All servicing must be
performed by Runco accredited service technicians.
Use replacement parts that are manufacturer-approved only. Use of any
other part other than the ones specified by the manufacturer can result
in fire, electric shock or other damage.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
73
Ventilation
➤
•
➤
Slots and vents in the projector provide ventilation. Never block or cover these openings.
This ensures reliable operation of the projector and prevents overheating.
Servicing
Section 4: Maintenance
4.2 Cleaning and
Maintenance
Guide
WARNING
Always power down and unplug the projector before cleaning or
servicing.
Part
Description
Frequency
Action
Lens
As required
CLEAN: Clean if absolutely necessary. A small
amount of dust on the lens has very little affect
on picture quality.
To clean: Apply a solvent such as acetone,
alcohol or vinegar sparingly to clean, lint-free
lens tissue. Wipe across the surface of the lens.
Do not scrub or rub tissue in circular motion, this
will scratch the lens. Do not reuse tissue. Do not
use cleaning tools treated with Ether. If particles
still appear on the lens, try using compressed air
to remove.
Lamp
CLEAN: Clean if absolutely necessary. Never
touch the glass surface of the lamp. Fingerprints
left on the glass will seriously degrade lamp
performance or cause “hotspots” which can
lead to an accumulation of intense heat in the
touched area and cause the lamp to shatter.
As required
To clean: Wait until lamp is cool. Moisten a
clean, lint-free cotton cloth with isopropyl alcohol
and gently rub the surface of the glass in a
circular motion until clean.
Covers
(External)
1000 hrs or
sooner if required
REPLACE: Refer to 4.4 Lamp Replacement
procedure later in this section.
As required
CLEAN: Clean dust from external covers using a
clean, lint free cotton cloth as required.
NOTE: Before cleaning the modules, it is
recommended that you install the lens cap. This
will keep dust particles from settling on the glass
surface of the lens.
Table 4.1. Maintenance Guide
74
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 4: Maintenance
The optional IR remote uses four AAA size, 1.5V alkaline batteries. To replace the batteries
simply turn the remote over and remove the battery cover.
4.3 Replacing Remote
Batteries
Remove and properly discard the old batteries. Insert new batteries in the proper positive/
negative orientation as shown etched in the bottom of the compartment (2). Replace the
cover by inserting the tabbed end into the opening and snapping the opposite end into
place.
1
Figure 4.1. Replacing remote batteries (underside of keypad shown)
Use the following instructions when replacing the lamp. The lamp is located at the back of
the projector (below the input panel) and can be accessed by removing the lamp access
panel. Use only the Runco approved Lamp and Filter Kit for your specific projector model.
See chart below.
Projector Model
Lamp (Watts)
Part Number
Runco VX-40d
1000W
RUPA-006400
Runco VX-50d
1200W
RUPA-006700
Runco VX-60d
1000W
RUPA-006800
Runco VX-80d
1200W
RUPA-006850
A lamp should be replaced when it reaches its end of life (1000 hours, typical) or
sooner if a noticeable degradation in brightness occurs (typical in aging lamps). You
can set the number of hours you expect to log with the lamp before replacing it, by
setting the Lamp Limit in the Lamp menu. You can also enable a warning message
to appear upon powering up the projector that will indicate the lamp has reached the
limit you set, by entering a checkmark beside the Lamp Message option. NOTE: The
lamp mode you choose to run the projector in may affect the lamp life.
Tools required: #1 Phillips screwdriver
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
75
4.4 Lamp and Filter
Replacement
Section 4: Maintenance
WARNING
Handle lamp with care. Lamp may explode if dropped.
Wear protective clothing and safety goggles when
handling lamps.
Use only Runco approved lamps provided for your projector.
1. Press to power down the projector. Wait at least 5 minutes to allow the internal cooling
fans to stop before unplugging the projector. This wait period is also required to allow the
lamp to sufficiently cool before handling.
WARNING
Always power down and unplug the projector prior to servicing.
Allow the lamp to cool before handling.
2. Using a screwdriver, loosen the four screws from the lamp door located at the back of
the projector, below the input panel. (Figure 4.2.)
Lamp door - 4 screws
Figure 4.2. Removing the Lamp Door
3. Pull (out) and turn the lamp lock lever, which is located to the left of the lamp module, a
quarter turn counter clockwise to the “unlock” position. (Figure 4.3.)
Figure 4.3. Unlocking the Lamp
76
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 4: Maintenance
4. Grasp the lamp by its housing only and pull it straight out (lamp slides along guides)
until it’s free. (Figure 4.4.) Discard the lamp using safe disposal/recycling practices
or contact your Runco dealer for a possible re-lamping program.
Figure 4.4. Removing the Lamp
5. Align the new lamp with the top and bottom guides on the left side of the lamp
compartment. (Figure 4.5.) Slide the lamp all the way in – a slightly harder push may be
required right at the end to make sure it is fully seated into the terminal block. NOTE: The
projector will not power up again if the lamp is not fully connected to the terminal block.
Figure 4.5. Installing a New Lamp
6. Pull (out) and turn the lamp lock lever (turned up in Step 3) a quarter turn clockwise to
“lock” the lamp in place. NOTE: If you can’t turn the lamp lock into position it is likely the
lamp is not fully inserted. In this case, partially remove the lamp and try pushing it back
in again. Then, try switching the lock lever to the “lock” position.
7. Replace the lamp door and tighten the four screws to secure.
8. The next time the projector is powered up, enter the new serial number of the newly
installed lamp. Access the Lamp menu and select “Change Lamp.”
Enter the serial number in the Lamp S/N text box using the numeric keypad.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
77
Section 4: Maintenance
4.5 Replacing the
Projection Lens
Use the following instructions when replacing a projection lens:
NOTE for first time use: The projection lens is shipped separately from the projector.
Before you install a lens it is important that you remove the lens plug from the lens
opening in the projector.
1. Power down the projector and wait five minutes to allow the lamp to cool before
continuing with Step 2.
2. Place the lens cap on the projection lens to protect it from being damaged during the
installation or removal process. For first time installations, remove the rear cap from
the lens – this protective cap is only used during shipping to protect the lens from
damage.
3. When removing the projection lens – Press and hold the “lens release” button
located in the top right corner of the lens panel. Grasping the lens barrel, turn it in a
counter-clockwise direction until it stops. Then pull it forward to remove it (disconnects
from the connector assembly).
OR
When installing a projection lens, make sure Steps 1 and 2 are complete. Slide the
new lens into the lens opening of the projector – make sure to align the connector that is
located on the side of the lens with the connector assembly on the lens retaining ring. As
you connect the lens, you may have to re-align it slightly until the tabs on the lens will fit
into the slots in the lens retaining ring. With the lens fully inserted (and connected) turn it
clockwise until the lens release button “pops” indicating the lens is fully inserted.
Figure 4.6. Lens Assembly (Front View)
78
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 4: Maintenance
Figure 4.7. Removing or Installing A Lens
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
79
Section 4: Maintenance
This page is intentionally left blank.
80
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
SECTION 5
Troubleshooting
If the projector does not appear to be operating properly, note the symptoms present
and use the following guide to assist you. If you cannot resolve the problems yourself,
contact your dealer for assistance.
NOTE: A qualified Runco service technician is required when opening the projector
to diagnose any “probable cause”.
SYMPTOM
The projector is on but
there’s no display...
CAUSE/REMEDY
Was a lens cover accidentally left on? Remove lens
cover.
Make sure the shutter is OPEN.
Is the lamp ignited? Check for interlock problems such
as an open lamp door OR check for light spillage out the
back.
Is the correct input selected? Check cable connections.
Check if menus appear on screen.
Can you access test patterns? Make sure there is not a
full black test pattern selected for display—press Menu
to access test patterns, then cycle patterns with keys.
Check your source connections again.
Severe motion
artifacts...
Most likely there is a synchronization problem with
reversed 3/2 pull-down in 60Hz-to-24Hz film-to-digital
conversion in your source. Correct at the source.
Was an excessive amount of keystone used?
Image appears
Check your Resizing selection.
“squeezed” or vertically
stretched into center of Check the DHD Controller’s aspect ratio selection.
screen
The display is jittery or
unstable...
If the display is jittery or blinking erratically, ensure that
the source is properly connected and of adequate
quality for detection. With a poor quality or improperly
connected source, the projector will repeatedly attempt
to display an image, however briefly.
The horizontal or vertical scan frequency of the input
signal may be out of range for the projector. Refer to
Section 6, Specifications for scan frequency ranges.
The sync signal may be inadequate. Correct the source
problem.
The display is faint...
Brightness and/or contrast and/or gamma may be set
incorrectly.
The source may be double terminated. Ensure the
source is terminated only once.
The source (if non-video) may need a different sync tip
clamp location.
The upper portion of
the display is waving,
tearing or jittering...
This can sometimes occur with video or VCR sources.
Check your source.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
81
5.1 Displays
Section 5: Troubleshooting
SYMPTOM
CAUSE/REMEDY
Portions of the display
are cut off or wrap to
the opposite edge...
Resizing and/or blanking may need adjustment.
The display appears
compressed ...
The aspect ratio selected at the DHD Controller may be
incorrect.
The horizontal or vertical scan frequency of the input signal
may be out of range for the projector. Refer to Section 6,
Specifications for scan frequency ranges.
Resizing, vertical stretch and positioning options may
be improperly adjusted for the incoming source signal.
(Example: The DVD player is set for the wrong screen
type.)
Data is cropped from
edges
Check settings for Blanking.
Display quality
appears to drift from
good to bad, bad to
good...
The source input signal may be of low quality.
The display has
suddenly frozen...
It’s possible that excessive voltage noise on the AC or
ground input has interrupted the projector’s ability to lock
on to a signal. Power down the projector and disconnect
from AC. Then plug in again and power up as usual.
Colors in the display
are inaccurate...
Try Auto Setup.
If incoming data is still missing from the image, reduce
the image size to within the display area available in the
projector.
The color, tint, color space, color temperature and/or
other settings may require adjustment.
Ensure signal connections are correct.
Make sure you are using the proper channel for this
source.
Values in Color
Saturation slidebars
vary over time...
Once defined, Color Saturation slidebar values fluctuate
over time and will likely be different upon subsequent
visits to this menu. This is normal and should be ignored,
as these changes do not redefine the x/y coordinates or
color gamut.
The display is not
rectangular...
Check leveling of the projector. Make sure that the lens
surface and screen are as parallel to each other as
possible.
The display is
“noisy”...
Display adjustment at your input source may be required.
The video input may not be terminated. Make sure the
video input is terminated (75Ω). If it is the last connection in
a loop-through chain, the video input should be terminated
at the last source input only.
The input signal and/or signal cables carrying the input
signal may be of poor quality.
If the distance between the input source device and the
projector is greater than 75 feet, signal amplification/
conditioning may be required.
If the source is a VCR or off-air broadcast, detail may be
set too high.
82
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 5: Troubleshooting
SYMPTOM
Lamp does not ignite
CAUSE/REMEDY
If the lamp won’t ignite, there may be an interlock failure
such as an open lamp door, or failed lamp fan. An error
code will display on the status LED display located on the
built in keypad.
If a temperature is too high (e.g.“DMD over critical temp
limit”), the lamp will not ignite until the temperature is low
enough. Cool the projector and try again.
If the lamp does not ignite after a second and third try,
replace the lamp.
Lamp suddenly turns
Off
Try increasing the lamp power.
The DMDs may be overheated.
Replace the lamp.
Flicker, Shadows or
Dimness
Increase lamp power, if possible.
Replace the lamp.
Intensity does not seem Make sure “Intensity” is selected in the Lamp menu.
to work
If the lamp power has increased to its maximum in order
to maintain an intensity setting, intensity is automatically
terminated. If the values shown in the Lamp menu indicate
that the lamp power has reached this “over-drive” state,
either reduce your intensity setting or install a new lamp.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
83
5.2 Lamp
Section 5: Troubleshooting
This page is intentionally left blank.
84
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
SECTION 6
Specifications
➤
Projector Type:
Digital Light Processing™ (DLP™),
3-Chip, 16:9 Darkchip2™ DMD™
Native Resolution:
1280 x 720
Aspect Ratios:
Determined by supplied DHD Video Processor
Video Standards:
NTSC, PAL
DTV Compatibility:
480p, 720p, 1080i
Scan Frequency:
Horizontal: 15 – 120kHz
Vertical: 23.97 – 150Hz
Picture Size
(16:9 screens)
Recommended Width: 72 – 192 in.
Maximum Width: 300 in.
Lens Option 1: Zoom 4.96 – 7.90
Throw Distance
(Factor x Screen Width) Lens Option 2: Zoom 1.65 – 1.95
Lens Option 3: Zoom 2.04 – 2.73
Lens Option 4: Zoom 2.86 – 4.83
Lens Option 5: Fixed 0.8 (for rear screen applications)
Horizontal and
Vertical Offset:
Horizontal offset varies per lens up to 50%, Vertical offset
varies per lens, up to 100%; Short Throw: H: 69%, V: 37%
(Contact Runco technical support for installation details.)
Lamp:
1000W Xenon lamp module
Lamp Life:
1000 Hours @ 6,500K
Inputs:
(1) Composite, (1) S-Video, (1) DVI,
(1) RGB/Component, (1) RS232, (1) RS422
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
85
VX-40d
Section 6: Specifications
VX-40d (continued) ➤
Brightness and
Contrast:
Cinema Standards Measurement System (CSMS) Specifications
- Brightness: 86 foot-Lamberts (fL)
- Contrast Ratio: 232:1 to 285:1 (variable depending on lens
aperture setting)
These measurements are taken from the projector in a controlled,
home theater environment. All measurements are made to ANSI/
NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial movie theaters to express image brightness at the screen
surface. The Society of Motion Picture and Television Engineers
(SMPTE) specifies 16 fL as the target image brightness for filmbased projectors using an open gate (without film in the projector).
More importantly, today SMPTE specifies 12 fL as the target image
brightness in Digital Cinema theaters. The foot-Lambert measurement is dependent on screen size, screen gain and projector light
output.
Home Theater Calibration Specifications
- Light Output: 2180 ANSI Lumens
- Contrast Ratio: 232:1 to 285:1
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
Industry-Standard Specifications
- Light Output: 4000 ANSI Lumens
- Contrast Ratio: 1500:1 to 1800:1
These are typical projector brightness and contrast specifications
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with
other manufacturers’ projectors. These measurements are typically taken at 9,000K to 13,000K to get expected performance
data when the projector is used in professional, commercial and
industrial displays.
12V Output:
See Controller for Specifications
Power Requirements:
100-240V AC, 50/60Hz, 1700W
Operating Environments: 40 to 95ºF (5 to 35ºC); 20-80% humidity (non-condensing)
Dimensions (w/o feet):
Width: 29.03 in. (737 mm)
Depth: 28.23 in. (717 mm)
Height: 12.24 in. (311 mm)
Weight (without lens):
85 lbs. (38.55 kg)
Regulatory Approvals:
Complies with FCC Class B, CE, C-Tick
Limited Warranty:
Projector: Two (2) years parts and labor from the date of
delivery to the end user.
Lamp Warranty: 1000 hours or six (6) months, whichever
comes first.
86
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 6: Specifications
➤
Projector Type:
Digital Light Processing™ (DLP™),
3-Chip, 16:9 Darkchip2™ DMD™
Native Resolution:
1280 x 720
Aspect Ratios:
Determined by supplied DHD Video Processor
Video Standards:
NTSC, PAL
DTV Compatibility:
480p, 720p, 1080i
Scan Frequency:
Horizontal: 15 – 120kHz
Vertical: 23.97 – 150Hz
Picture Size
(16:9 screens)
Recommended Width: 72 – 240 in.
Maximum Width: 350 in.
Lens Option 1: Zoom 4.96 – 7.90
Throw Distance
(Factor x Screen Width) Lens Option 2: Zoom 1.65 – 1.95
Lens Option 3: Zoom 2.04 – 2.73
Lens Option 4: Zoom 2.86 – 4.83
Lens Option 5: Fixed 0.8 (for rear screen applications)
Horizontal and
Vertical Offset:
Horizontal offset varies per lens up to 50%, Vertical offset
varies per lens, up to 100%; Short Throw: H: 69%, V: 37%
(Contact Runco technical support for installation details.)
Lamp:
1.2kW Xenon lamp module
Lamp Life:
1000 Hours @ 6,500K
Inputs:
(1) Composite, (1) S-Video, (1) DVI,
(1) RGB/Component, (1) RS232, (1) RS422
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
87
VX-50d
Section 6: Specifications
VX-50d (continued) ➤
Brightness and
Contrast:
Cinema Standards Measurement System (CSMS) Specifications
- Brightness: 107.3 foot-Lamberts (fL)
- Contrast Ratio: 229:1 to 279:1 (variable depending on lens
aperture setting)
These measurements are taken from the projector in a controlled,
home theater environment. All measurements are made to ANSI/
NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial movie theaters to express image brightness at the screen
surface. The Society of Motion Picture and Television Engineers
(SMPTE) specifies 16 fL as the target image brightness for filmbased projectors using an open gate (without film in the projector).
More importantly, today SMPTE specifies 12 fL as the target image
brightness in Digital Cinema theaters. The foot-Lambert measurement is dependent on screen size, screen gain and projector light
output.
Home Theater Calibration Specifications
- Light Output: 3462 ANSI Lumens
- Contrast Ratio: 229:1 to 279:1
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
Industry-Standard Specifications
- Light Output: 6000 ANSI Lumens
- Contrast Ratio: 1500:1 to 1800:1
These are typical projector brightness and contrast specifications
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with
other manufacturers’ projectors. These measurements are typically taken at 9,000K to 13,000K to get expected performance
data when the projector is used in professional, commercial and
industrial displays.
12V Output:
See Controller for Specifications
Power Requirements:
200-240V AC, 50/60Hz, 2100W
Operating Environments: 40 to 95ºF (5 to 35ºC); 20-80% humidity (non-condensing)
Dimensions (w/o feet):
Width: 29.03 in. (737 mm)
Depth: 28.23 in. (717 mm)
Height: 12.24 in. (311 mm)
Weight (without lens):
89 lbs. (40.37 kg)
Regulatory Approvals:
Complies with FCC Class B, CE, C-Tick
Limited Warranty:
Projector: Two (2) years parts and labor from the date of
delivery to the end user.
Lamp Warranty: 1000 hours or six (6) months, whichever
comes first.
88
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 6: Specifications
➤
Projector Type:
Digital Light Processing™ (DLP™),
3-Chip, Darkchip2™ DMD™
Native Resolution:
1400 x 1050
Aspect Ratios:
Determined by Supplied DHD Video Processor
Video Standards:
NTSC, PAL
DTV Compatibility:
480p, 720p, 1080i
Scan Frequency:
Horizontal: 15 – 120kHz
Vertical: 23.97 – 150Hz
Picture Size
(16:9 screens)
Recommended Width: 72 – 192 in.
Maximum Width: 300 in.
Lens Option 1: Zoom 4.48 – 7.15
Throw Distance
(Factor x Screen Width) Lens Option 2: Zoom 1.48 – 1.75
Lens Option 3: Zoom 1.81 – 2.40
Lens Option 4: Zoom 2.56 – 4.35
Lens Option 5: Fixed 0.75 (for rear screen applications)
Horizontal and
Vertical Offset:
Horizontal offset varies per lens up to 50%, Vertical offset varies per lens, up to 100%; Short Throw: H: 69%, V: 37%
(Contact Runco technical support for installation details.)
Lamp:
1000W Xenon lamp module
Lamp Life:
1000 Hours @ 6500K
Inputs:
(1) Composite, (1) S-Video, (1) DVI,
(1) RGB/ Component, (1) RS232, (1) RS422
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
89
VX-60d
Section 6: Specifications
VX-60d (continued) ➤
Brightness and
Contrast:
Cinema Standards Measurement System (CSMS) Specifications
- Brightness: 94 foot-Lamberts (fL)
- Contrast Ratio: 227:1 to 282:1 (variable depending on lens
aperture setting)
These measurements are taken from the projector in a controlled,
home theater environment. All measurements are made to ANSI/
NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial
movie theaters to express image brightness at the screen surface.
The Society of Motion Picture and Television Engineers (SMPTE)
specifies 16 fL as the target image brightness for film-based
projectors using an open gate (without film in the projector). More
importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters. The foot-Lambert measurement is
dependent on screen size, screen gain and projector light output.
Home Theater Calibration Specifications
- Light Output: 2360 ANSI Lumens
- Contrast Ratio: 227:1 to 282:1
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
Industry-Standard Specifications
- Light Output: 4000 ANSI Lumens
- Contrast Ratio: 1500:1 to 1800:1
These are typical projector brightness and contrast specifications
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with
other manufacturers’ projectors. These measurements are typically
taken at 9,000K to 13,000K to get expected performance data
when the projector is used in professional, commercial and industrial
displays.
12V Output:
See Controller for Specifications
Power Requirements:
100-240V AC, 50/60Hz, 1700W
Operating Environments: 40 to 95ºF (5 to 35ºC); 20-80% humidity
(non-condensing)
Dimensions (w/o feet):
Width: 29.03 in. (737 mm)
Depth: 28.23 in. (717 mm)
Height: 12.24 in. (311 mm)
Weight (without lens):
85 lbs. (38.55 kg)
Regulatory Approvals:
Complies with FCC Class B, CE, C-Tick
Limited Warranty:
Projector: Two (2) years parts and labor from the date of
delivery to the end user.
Lamp Warranty: 1000 hours or six (6) months, whichever
comes first.
90
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Section 6: Specifications
➤
Projector Type:
Digital Light Processing™ (DLP™),
3-Chip, Darkchip2™ DMD™
Native Resolution:
1400 x 1050
Aspect Ratios:
Determined by Supplied DHD Video Processor
Video Standards:
NTSC, PAL
DTV Compatibility:
480p, 720p, 1080i
Scan Frequency:
Horizontal: 15 – 120kHz
Vertical: 23.97 – 150Hz
Picture Size
(16:9 screens)
Recommended Width: 72 – 288 in.
Maximum Width: 375 in.
Throw Distance
(Factor x Screen Width)
Lens Option 1: Zoom 4.48 – 7.15
Lens Option 2: Zoom 1.48 – 1.75
Lens Option 3: Zoom 1.81 – 2.40
Lens Option 4: Zoom 2.56 – 4.35
Lens Option 5: Fixed 0.75 (for rear screen applications)
Horizontal and
Vertical Offset:
Horizontal offset varies per lens up to 50%, Vertical offset
varies per lens, up to 100%; Short Throw: H: 69%, V: 37%
(Contact Runco technical support for installation details.)
Lamp:
1.2kW Xenon lamp module
Lamp Life:
1000 Hours @ 6500K
Inputs:
(1) Composite, (1) S-Video, (1) DVI,
(1) RGB/ Component, (1) RS232, (1) RS422
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
91
VX-80d
Section 6: Specifications
VX-80d (continued) ➤
Brightness and
Contrast:
Cinema Standards Measurement System (CSMS) Specifications
- Brightness: 188.6 foot-Lamberts (fL)
- Contrast Ratio: 225:1 to 277:1 (variable depending on lens
aperture setting)
These measurements are taken from the projector in a controlled,
home theater environment. All measurements are made to ANSI/
NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial movie theaters to express image brightness at the screen
surface. The Society of Motion Picture and Television Engineers
(SMPTE) specifies 16 fL as the target image brightness for filmbased projectors using an open gate (without film in the projector).
More importantly, today SMPTE specifies 12 fL as the target image
brightness in Digital Cinema theaters. The foot-Lambert measurement is dependent on screen size, screen gain and projector light
output.
Home Theater Calibration Specifications
- Light Output: 5740 ANSI Lumens
- Contrast Ratio: 225:1 to 277:1
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
Industry-Standard Specifications
- Light Output: 8000 ANSI Lumens
- Contrast Ratio: 1500:1 to 1800:1
These are typical projector brightness and contrast specifications
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with
other manufacturers’ projectors. These measurements are typically taken at 9,000K to 13,000K to get expected performance
data when the projector is used in professional, commercial and
industrial displays.
12V Output:
See Controller for Specifications
Power Requirements:
200-240V AC, 50/60Hz, 2100W
Operating Environments: 40 to 95ºF (5 to 35ºC); 20-80% humidity
(non-condensing)
Dimensions (w/o feet):
Width: 29.03 in. (737 mm)
Depth: 28.23 in. (717 mm)
Height: 12.24 in. (311 mm)
Weight (without lens):
89 lbs. (40.37 kg)
Regulatory Approvals:
Complies with FCC Class B, CE, C-Tick
Limited Warranty:
Projector: Two (2) years parts and labor from the date of
delivery to the end user.
Lamp Warranty: 1000 hours or six (6) months, whichever
comes first.
92
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
APPENDIX A
Glossary
This appendix defines the specific terms used in this manual as they apply to this projector.
Also included are other general terms commonly used in the projection industry.
Active Line Time ➤
Ambient Light Rejection ➤
Analog Video ➤
Anamorphic ➤
ANSI ➤
The time, inside one horizontal scan line, during which video is generated.
The ability of a screen to reflect ambient light in a direction away from the “line of best
viewing”. Curved screens usually have good ambient light rejection. Flat screens usually
have less ambient light rejection.
The video output of most computers and videotape machines. Analog video can generate
a large number of colors.
Having or requiring a linear distortion, generally in the horizontal direction.
Anamorphic lenses can restore a ‘scope’ (CinemaScope) or ‘flat’ format film frame to the
correct wide-screen appearance by increasing its horizontal proportion.
The American National Standards Institute is the organization that denotes the
measurement standard for lamp brightness.
Aspect Ratio ➤
The ratio of the width of an image to its height, such as the 4:3 aspect ratio common in
video output. Can also be expressed as a decimal number, such as 1.77, 1.85 or 2.39.
The larger the ratio or decimal, the wider and “less square” the image.
Auto Source ➤
The ability of the projector to automatically recognize and synchronize to the horizontal
and vertical scan frequencies of an input signal for proper display.
Bandwidth ➤
The frequency range of the projector’s video amplifier.
Baud Rate ➤
The speed (bits-per-second) at which serial communications travel from their origin.
Blanking Time ➤
Brightness ➤
Candela or Candle ➤
Channel ➤
Channel List ➤
Channel Number ➤
Checkbox ➤
Chrominance ➤
Color Gamut ➤
Color Shift ➤
The time inside one scan line during which video is not generated. The blanking time of the
input signal must be equal to or greater than the retrace time of the projector.
In projection, brightness usually describes the amount of light emitted from a surface such
as a screen. It is measured in foot-lamberts or candelas per square meter.
Unit of measure for measuring intensity of light.
A collection of measurements stored by the projector for a given input source, including
frequencies, pulse width, polarity, syncs, channel number and location, user adjustable
display settings, etc. Use channels to switch between a variety of setups quickly,
automatically recalling previously defined display parameters.
A list/menu of previously-defined channels available in projector memory.
A number that uniquely identifies a specific channel retained in projector memory. The
projector can retain up to 99 channels.
A menu item that indicates whether an option is currently in effect (checked) or not
(unchecked).
The signal representing the color information (hue and saturation) when the image is
represented as separate chrominance and luminance. Same as “chroma”.
The range of colors allowed in a specific system, as defined within a triangular area located
on the CIE color locus diagram whose corners are the three primaries defined in the
system. Also known as color space.
A change in the tint of a white field across an image.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
93
Appendix A: Glossary
Color Temperature ➤
Component Video ➤
Composite Video ➤
Contrast (ratio) ➤
Convergence ➤
CSMS ➤
Curved Screen ➤
DDC ➤
DDI ➤
DMD™ ➤
Decoder ➤
Detail ➤
The coloration (reddish, white, bluish, greenish, etc.) of white in an image, measured using
the Kelvin (degrees K) temperature scale. Higher temperatures output more light.
See YCbCr or YPbPr.
The output of video tape players and some computers, characterized by synchronization,
luminance and color signals combined on one output cable.
The degree of difference between the lightest and darkest areas of the image.
The alignment of the red, green, and blue elements of a projected image so that they
appear as a single element.
The Cinema Standards Measurement System (CSMS) is a method of measuring home
theater projector light output in terms that Runco believes can be better understood by
the typical consumer. It consists of three separate measurement steps to provide three
separate ratings for the projector: ANSI Lumens, ANSI Home Theater Lumens and FootLamberts.
A projection screen which is slightly concave for improved screen gain. Curved screens
usually have screen gains, which are greater than 1 but viewing angles much less than
180°. Curved screens are not recommended for use with this projector.
The Display Data Channel VESA standard enables communication between PCs and
monitors, and is based on E-EDID protocol.
A “direct digital interface” signal can be supplied to the projector via an optional digital
input module installed in INPUT 5. For example, you can input an SMPTE- 259M signal
using a Serial Digital Input Module or input an SMPTE-272M signal from a Digital HDTV
Serial Input Module.
Digital Micromirror Devices™ used in this projector for processing red, green and blue
color data.
Located at INPUT 3 and INPUT 4, this device converts NTSC 3.58, NTSC 4.4, PAL, PALN, PAL-M, or SECAM to RGB video.
The sharpness of a display from a video source.
Diffused Screen ➤
A type of rear-projection screen which spreads the light striking it. Screen gain is less than
1 but audience viewing angles are increased.
Display Setting ➤
An adjustment that affects the display of an image. Such display settings include contrast,
brightness, tint, blanking, size, offsets, and others.
Dot Clock ➤
The maximum frequency of the pixel clock. Also known as pixel clock rate.
E-EDID ➤
The Enhanced Extended Display Identification Data standard, established by VESA,
enables properties (such as resolution) of a display device to be detected by the display
card in a controlling device such as a PC. The PC, in turn, can then output in a matching
format to fill the display. Some sources used with the projector are VESA EEDID reported.
Flicker ➤
A very rapid variation in image brightness caused by a frame rate that is too slow. (See
Interlace) See also Lamp Flicker.
Foot-Candle ➤
Foot-Lambert ➤
Frame Rate ➤
The intensity of visible light per square foot.
The luminance (brightness) which results from one foot-candle of illumination falling on a
perfectly diffuse surface.
The frequency at which complete images are generated. For non-interlaced signals, the
frame rate is identical to the vertical frequency. For interlaced signals, the frame rate (also
known as field rate) is one half of vertical frequency.
94
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Appendix A: Glossary
Gain or Screen Gain ➤
The ability of a screen to direct incident light to an audience. A flat matte white wall has
a gain of approximately 1. Screens with gain less than 1 attenuate incident light; screens
with gain more than 1 direct more incident light to the audience but have a narrow viewing
angle. For example: An image reflecting off a 10 gain screen appears 10 times brighter
than it would if reflected off a matte white wall. Curved screens usually have larger gain
than flat screens.
HDCP ➤
High-bandwidth Digital Content Protection (HDCP) is a specification developed by the Intel®
corporation for protecting digital entertainment content that uses a digital visual interface
(DVI). HDCP encrypts the transmission of digital content (signal) between the video source
and the digital display. HDCP does not prevent the copying or recording of digital content; it
only protects the integrity of content as it is transmitted.
HDTV ➤
High-definition Television (1035, 1080 and 1125 lines interlace, and 720 and 1080 line
progressive formats with a 16:9 (i.e. 1.77) aspect ratio.
Help Text ➤
A display of help information regarding the current task or presentation.
Horizontal Frequency ➤
The frequency at which scan lines are generated, which varies amongst sources. Also called
horizontal scan rate or line rate.
Horizontal Offset ➤
The difference between the center of the projected image and the center of the projector
lens. For clarity, offset is often expressed as the maximum amount of the image that can
be projected to one side of the lens center without degrading the image quality. Horizontal
offset ranges can be affected by the type of lens in use, and whether or not the image is
offset vertically at the same time.
Hot Spot ➤
A circular area of a screen where the image appears brighter than elsewhere on the screen.
A hot spot appears along the line of sight and “moves” with the line of sight. High gain
screens and rear screens designed for slide or movie projection usually have a hot spot.
Input ➤
A physical connection route for a source signal, described by a 2-digit number representing
1) its switcher/projector location and 2) its slot in the switcher/projector.
Input Signal ➤
Signal sent from a source device to the projector.
Interface ➤
A device, such as the Serial Digital Input Module, that accepts an input signal for display by
the projector.
Interlace ➤
A method used by video tape players and some computers to double the vertical resolution
without increasing the horizontal line rate. If the resulting frame/field rate is too low, the
image may flicker depending on the image content.
Keypad ➤
A small push-button device for controlling most projector settings and operation. For more
information, refer to 3.3, Using the Keypad.
Keystone ➤
A distortion of the image which occurs when the top and bottom borders of the image
are unequal in length. Side borders both slant in or out, producing a “keyhole” shaped
image. It is caused when the screen and lens surface are not parallel, or by poor Keystone
adjustment.
Lamp Flicker ➤
As the lamp ages, the shape of two anodes may change from two points to a flattened
state. When this occurs, the arc jumps across the gap from varying points. This is seen as
image flicker. Turning the Lamp Conditioning feature ON will pulse the lamp and gradually
“condition” the two anodes back to two points. Lamp Conditioning may take seconds,
minutes or hours to reach full effectiveness. NOTE: Lamp flicker can occur at any time in
the lamps life. The length of time, over which flicker may occur varies considerably and
unpredictably. This behavior is inherent in UHP lamps.
Linearity ➤
The reproduction of the horizontal and vertical size of characters and/or shapes over the
entire screen.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
95
Appendix A: Glossary
Appendix A: Glossary
Line of Best Viewing ➤
When light from a projector is incident on a screen, the light reflects from the screen such
that the angle of reflection equals the angle of incidence. The Line of Best Viewing is along
the line of reflection.
Loopthrough (Loopthru) ➤
The method of feeding a series of high impedance inputs from a single video source with a
coaxial transmission line in such a manner that the line is terminated with its characteristic
impedance at the last input on the line.
Lumen ➤
Luminance ➤
Lux ➤
Menu ➤
The unit of measure for the amount of visible light emitted by a light source.
The signal representing the measurable intensity (comparable to brightness) of an
electronic image when the image is represented as separate chrominance and luminance.
Luminance also expresses the light intensity of a diffuse source as a function of its area;
measured in lumens or candles per square foot (1 lumen per square foot = 1 foot-lambert).
SMPTE RP 98 calls for a luminance of 12 to 22 foot-lamberts for theatre screens. See:
Foot-lambert.
The amount of visible light per square meter incident on a surface. 1 lux = 1 lumen/square
meter = 0.093 foot-candles
A list of selectable options displayed on the screen.
NTSC Video ➤
A video output format of some video tape and disk players. There are two types of NTSC
(National Television Standards Committee) video: NTSC 3.58 and NTSC 4.43. NTSC 3.58
is used primarily in North America and Japan. NTSC 4.43 is less commonly used.
Optical Screen ➤
A type of rear-projection screen which re-directs light through the screen to increase
image brightness in front of the screen. Screen gain is usually greater than 1 but audience
viewing angles are reduced.
PAL Video ➤
Pixel ➤
Pixel Phase ➤
Pixel Tracking ➤
Projector-to-Screen ➤
Distance
Protocol ➤
Pull-down List ➤
PAL (Phase Alternating Line) video is a 50 Hz standard with 768 x 576 resolution. It is
found on some video tape and disk players (used primarily in Europe, China and some
South American and African countries).
The smallest discernible element of data from a computer-generated image.
The phase of the pixel sampling clock relative to incoming data.
The frequency of the pixel sampling clock, indicated by the number of pixels per line.
The distance between the projector’s lens and the screen. Also called “Throw Distance”.
The syntax used by the communication system.
A selectable menu item that unfolds into a list of options pertaining to it.
Rear Screen ➤
A translucent panel for screen projection. Incident light travels through the incident surface
of a rear screen and forms an image on the other surface.
Resizing ➤
The ability to manipulate through software commands the physical size, placement and/or
aspect ratio of an image.
Resolution (lens) ➤
Resolution (projector) ➤
Retrace Time ➤
(Horizontal)
Rise Time ➤
The maximum number of alternate white and black horizontal lines that can be
distinguished on a screen when a photographic target is placed between the lens and a
light source and illuminated by that source.
The maximum number of pixels that the projector can display horizontally and vertically
across an image, such as 1024 x 768 (called XGA).
The minimum time required for a CRT projector to move the position of the scanning spot
from the right edge to the left edge.
The time required by the video amplifier of the projector to increase its output from 10% to
90% of the maximum value.
96
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Appendix A: Glossary
Appendix A: Glossary
RGB Video ➤
The video output (analog or digital) of most computers. Analog RGB video can have 3, 4,
or 5 wires — one each for red, green, and blue, and either none, one or two for sync. For
three-wire RGB, the green wire usually provides sync. (See TTL Video).
RS232 ➤
A common asynchronous data transmission standard recommended by the Electronics
Industries Association (EIA). Also called serial communication.
RS422 ➤
A less common asynchronous data transmission standard in which balanced differential
voltage is specified. RS422 is especially suited to long distances.
S-Video ➤
Scan Frequency ➤
The output from certain video tape players and video equipment. S-Video separates sync
and luminance from color information, typically producing a higher quality display than
composite video.
The horizontal or vertical frequency at which images are generated. Also known as scan
rate or refresh rate.
Scan Line ➤
One horizontal line on the display.
Scan Rate ➤
The horizontal or vertical frequency at which images are generated.
SECAM ➤
Slidebar ➤
Source ➤
Source Setup ➤
Switcher ➤
Sync ➤
A video output format of some video tape and disk players (used primarily in France).
SECAM (Sequential Couleur avec Mémoire) signals are similar in resolution and frequency
to PAL signals. The primary difference between the two standards is in the way color
information is encoded.
A slidebar is a graphical display of an adjustable setting. The numerical setting often
represents a percentage but can be a specific unit such as degrees Kelvin.
The device, such as a computer or VCR, connected to the projector for display. A source
may have numerous corresponding channels defined and recognized by the projector. See
Input.
See Channel.
A signal selector that can be connected to a projector for the purpose of adding more
sources.
This term refers to the part of the video signal that is used to stabilize the picture. Sync can
occur in three forms:
1) “Composite sync”: the horizontal and vertical components are together on one cable.
2) “Sync-on-green”: the sync is part of the green video.
3) “Separate sync” or “H.SYNC and V.SYNC”: the horizontal and vertical components of
the sync are on two separate cables.
Sync Width ➤
TTL Video ➤
Terminated ➤
Throw Distance ➤
Throw Ratio ➤
Tint ➤
The duration of each sync pulse generated by a computer. The sync width is part of the
blanking time.
A type of RGB video with digital characteristics.
A wire connecting a single video source to a display device, such as a projector, must be
terminated by a resistance (usually 75Ω for video).
The distance between the projector’s lens and the screen. Also called “Projector-to-Screen
Distance”. Always use the correct Runco throw distance formula to calculate the proper
throw distance required for your lens.
Throw ratio = throw distance / screen width. Typically used to differentiate lenses.
Balance of red-to-green necessary for realistic representation of NTSC signals.
Variable Scan ➤
The ability of a projector to synchronize to inputs with frequencies within a specified range.
Vertical Frequency ➤
The frequency at which images are generated. Vertical frequencies vary amongst sources.
Also called vertical scan rate.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
97
Appendix A: Glossary
Vertical Offset ➤
The difference between the center of the projected image and the center of the projector
lens. For clarity, offset is often expressed as the maximum amount of the image that can
be projected above or below the lens center without degrading the image quality. Vertical
offset ranges depend on the type of lens in use, and whether or not the image is offset
horizontally at the same time.
Video ➤
The signal that is used by display devices (such as projectors) to generate an image. This
term also refers to the output of video tape/disk players and computers.
Video Decoder ➤
Video Standard ➤
An optional device that converts NTSC 3.58, NTSC 4.4, PAL, PAL-N, PAL-M or SECAM to
RGB video.
A specific type of video signal, such as NTSC, PAL, SECAM. This projector can
automatically recognize and interpret the incoming standard and display accordingly.
Viewing Angle ➤
Screens do not reflect equally in all directions. Most light is reflected in a conical volume
centered around the “line of best viewing”. Maximum brightness is perceived if you are
within the viewing cone defined by the horizontal and vertical viewing angles.
White Balance ➤
The color temperature of white used by the projector.
White Field ➤
The area of an image that is white only. For example, a full white field is an image that is
white everywhere. A 10% white field is a white area (usually rectangular) that occupies
10% of the image; the remaining 90% is black.
YCbCr ➤
A high-end digital component video signal.
YPbPr ➤
A high-end analog component video signal. Sometimes called YUV, Component, or Y, R-Y,
B-Y, the YPbPr signal by-passes the video decoder in this projector.
YUV ➤
Zoom ➤
See YPbPr.
The adjustment of image size by means of a zoom lens.
98
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
APPENDIX B
Serial Communications Cables
A serial link of RS232 or RS422 enables ASCII communication with the projector so that it
can be controlled remotely from a PC or other controller. From a PC, connect a standard
9-wire RS232 serial cable to the RS232 IN port. Or, for long-distance (>100 ft.) links with
an RS422-compatible PC or controller, connect RS422 cable to the RS422 port.
From projector to DHD Controller (RS232)
1 Gnd
2 Rx
3 Tx
4 Gnd
1 Gnd
2 Rx
3 Tx
4 Gnd
From projector to Automation System
Automation
System
From projector to RS422 compatible control system
▪ Wiring from your control system (or RS232-toRS422 adapter) may vary. Consult the
documentation for your device.
▪ Connect Tx+ to Rx+
▪ Connect Tx- to Rx▪ Connect Rx+ to Tx+
▪ Connect Rx- to Tx-
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
99
Appendix B: Serial Communications Cables
This page is intentionally left blank.
100
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
APPENDIX C
Throw Distance
Calculating Throw Distance
It is important throw distance be precisely calculated for your installation using the
appropriate formula from the chart below. To calculate throw distance you must know the
screen size and the lens type installed in the projector. In general, the larger you want the
image to be the greater the distance you must allow between the lens and the screen.
NOTES: 1) Throw distance is
measured from the screen to
the center of the projector’s
lens. 2) This measurement is not
necessarily parallel to the floor as
the projector and/or screen may
be inclined.
Throw Distance (TD) is measured from the
screen to the center of the projector’s lens.
Lens Option
VX-40d / VX-50d Throw Distances
VX-60d / VX-80d Throw Distances
1
1.65 - 1.95
1.48 - 1.75
2
2.04 - 2.73
1.81 - 2.40
3
2.86 - 4.83
2.56 - 4.35
4
4.96 - 7.90
4.48 - 7.15
5
0.8 (Approx.)
0.75 (Approx.)
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
101
Appendix C: Throw Distance
This page is intentionally left blank.
102
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
APPENDIX D
Optional Input Modules
There are many optional input modules and accessories currently available for this
projector. Contact your dealer for a complete and up-to-date listing.
➤
RGB500 Input Module
➤
The RGB500 Input Module may be installed in this projector, a Marquee Signal Switcher,
or a Marquee Case/Power Supply. The module receives analog RGB input signals from
computers or other RGB source devices.
RGB400BA Input Module
RGB500 Features
• accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or separate
horizontal and vertical sync), up to 500 MHz bandwidth
• accepts YPbPr, composite (on green) and Y/C (on red/blue)
• BNC connectors for RGB signal inputs
NOTE: The audio connectors are not functional.
The RGB400 Buffered Amplifier Input Module may be installed in this projector, in a
Marquee Signal Switcher or in a Marquee Case/Power Supply. Connect three-, four-, or
five-wire RGB video signals of up to 400 MHz bandwidth, signals typically produced by
high-resolution computer or workstations. The buffering capability of the module enables
the incoming signal to be sent to a remote destination. Inputs are 75Ω terminated.
RGB400BA Features
• accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or separate
horizontal and vertical sync)
• accepts YPbPr, composite (on green) and Y/C (on red/blue)
• BNC connectors for RGB signal inputs
• Buffered signals to a remote destination
NOTE: The audio connectors are not functional.
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
103
Appendix D: Optional Input Modules
RGB400 Active Loop-Thru ➤
Input Module
The RGB400 ALT Input Module may be installed in this projector, a Marquee Signal
Switcher, or a Marquee Case/Power Supply. The module receives analog RGB input
signals from computers or other RGB source devices. Video inputs are 75Ω terminated.
Video outputs provide buffered loop-through to another display device.
RGB400ALT Features
• accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or separate
horizontal and vertical sync)
• accepts YPbPr, composite (on green) and Y/C (on red/blue)
• BNC connectors for RGB signal inputs
• buffered loop-through video outputs
NOTE: The audio connectors are not functional.
PC250 Analog Input Module ➤
The PC250 Analog Input Module may be installed in this projector, a Marquee Signal
Switcher or a Marquee Case/Power Supply. The module receives analog RGB input signals
from IBM PC compatibles or Macintosh computers. Video inputs are 75Ω terminated.
Video outputs are provided for buffered loop-through to another display device.
PC250 Analog Features
• accepts VGA or MAC RGB video
• 15 pin D connectors for video
• active loop-through video outputs
NOTES: 1) This interface does not accept VGA and MAC signals simultaneously. 2) The
audio connectors are not functional. 3) Trademarks are the rights of their respective
owners.
104
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
Appendix D: Optional Input Modules
➤
The module receives either composite video or S-video input signals from tape or disk
players (do not connect both types of signals simultaneously). Video inputs are 75Ω
terminated. Video outputs are provided for buffered loop-through to another display
device.
Composite / S-Video
Input Module
Composite/S-video Features
• BNC connectors for composite RGB signals
• 4-pin mini-DIN connectors for S-Video signals
• buffered loop-through video outputs
NOTES:
1) This interface is not a decoder. NTSC, PAL, or SECAM signals must connect to the
video decoder installed at INPUT 3 / INPUT 4.
2) The audio connectors are not functional.
3) Do not connect both composite video and S-video signals to the Composite / SVideo Input Module. Connect one or the other, even when plugged into a switcher.
Features
• supports Digital Visual Interface (DVI) single-channel
• supports VESA® Extended Display Identification Data (EDID™)
• provides an active-loop-through using a DVI connector (conforming to the DVI
Specification)
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
105
➤
This module can display digital video input signals conforming to the DVI (Digital Visual
Interface) single-channel standard.
DVI Input Module
Appendix D: Optional Input Modules
Appendix D: Optional Input Modules
Serial Digital Input Module ➤
The module accepts a serial digital 4:2:2 component video signal (YCbCr) via a single
SERIAL IN BNC connector. The signal can loop through the SERIAL OUT BNC connector
to another device (such as another projector). Inputs are 75Ω Terminated.
SDI Features
• accepts serial digital 4:2:2 component video (YCbCr)
Dual SD/HD-SDI Module ➤
•
provides both a SERIAL IN and a SERIAL OUT BNC connector includes status
LEDs for signal and error
•
SMPTE 259M compatible
The Dual SD/HD-SDI Module enables incoming serial digital (SD or HD) data to be tiled
across multiple screen displays, overlapped for extra-bright displays, or distributed to
additional projectors for multiple, same-image screens.
Dual SD/HD-SDI Features
• Accepts and decodes up to two serial digital inputs
• Outputs up to two 10-bit YCbCr 4:2:2 video signals
• Provides input(s) to output(s) loop-through capability
• Supplies interchangeable inputs as part of the Picture-in Picture display
• SMPTE 259M compatible
106
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
SERIAL NUMBE R
RUMA-011010
rev 08-29-05
Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300
www.runco.com