Bissell TWIN POWER DUAL CYCLONIC User`s guide

Twin Power Dual Cyclonic
B A G L E S S
V A C U U M
USER’S GUIDE
3950 SERIES 220-240V
3
Safety Instructions
4
Product View
5-6
Assembly
6-9
Operation
10-16
Maintenance and Care
17
Troubleshooting
18
Consumer Services
19
Replacement Parts
20
Warranty
Thanks for buying a BISSELL Vacuum
We’re glad you purchased a BISSELL vacuum. Everything we know about
floor care went into the design and construction of this complete,
high-tech home cleaning system.
Your BISSELL vacuum is well made, and we back it with a limited one
year warranty. We also stand behind it with a knowledgeable, dedicated
Consumer Services department, so, should you ever have a problem, you’ll
receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is
a global leader in the design, manufacture, and service of high quality
homecare products like your BISSELL vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
22
www.bissell.com
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance,
basic precautions should be observed,
including the following:
■ Remove plug from electrical outlet before cleaning or
Read all instructions
before using your
upright VACUUM.
by the manufacturer or its service agent in order to
avoid a hazard.
■ Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, petrol, etc.).
■ Do not allow to be used as a toy.
■ Do not use for any purpose other than described in
this User’s Guide.
■ Use only manufacturer’s recommended attachments.
■ Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
■ Keep appliance on a level surface.
■ Turn off all controls before unplugging.
■ Be extra careful when cleaning stairs.
■ This appliance is provided with double
insulation. Use only identical replacement parts.
■ Do not use without debris tank and/or filters in
place.
■ Pay close attention when working
around children.
WARNING:
To reduce
the risk of fire, electric shock,
or injury:
■ Use indoors only.
■ Do not leave machine when it is plugged in.
■ Do not use with damaged cord or plug.
■ If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, return it to a service agent.
■ Do not handle unit with wet hands.
■ Do not pull or carry by cord, use cord as a handle,
close door on cord, pull cord around sharp corners
or edges, run appliance over cord, or expose cord to
heated surfaces.
■ Do not unplug by pulling on cord. unplug by
grasping plug.
■ Do not run appliance over cord.
■ Do not handle plug or appliance with wet hands.
■ Do not expose hair, loose clothing, fingers or body
parts to openings or moving parts.
■ Do not pick up hot or burning objects such as
cigarettes, matches, or hot ashes.
■ Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc.) or use in the
presence of explosive liquids or vapour.
■ Do not use appliance in an enclosed space filled with
vapours given off by oil base paint, paint
thinner, some moth proofing substances, flammable
dust, or other explosive or toxic vapours.
■ Not intended for use by young children or infirm
persons without supervision.
■ Young children should be supervised to ensure that they
do not play with the appliance.
www.bissell.com
maintaining the appliance.
■ If the supply cord is damaged, it must be replaced
SAVE THESE
INSTRUCTIONS.
This model is for HOUSEHOLD use only.
IMPORTANT
FOR OPERATION ON A 220-240 VOLT A.C. 50/60 Hz
POWER SUPPLY ONLY.
FOR RESIDENTS OF THE
UNITED KINGDOM ONLY
If your appliance is fitted with a nonrewireable BS
1363 plug it must not be used unless a 13 amp (ASTA
approved to BS 1362) fuse is fitted in the carrier
contained in the plug. (Spares may be obtained from
your BISSELL supplier). If for any reason the plug is cut
off, it must be disposed of, as it is an electric shock
hazard should it be inserted into a 13 amp socket.
3
Product view
Ergonomic
Loop Handle
Hose and Cord Clip
Quick Release™
Cord Wrap
Dusting Brush/
Upholstery Tool
Carry Handle
Power Cord
Stretch Hose
Crevice Tool
Extension Wand
Twist ‘n
Snap™
Hose
Pet TurboBrush™
Power Switch
Clean Filter Indicator
Lower
Hose Clip
Upper Tank
HEPA Media
Post Motor Filter
Easy Empty™
Dirt Container
Washable
Pre-Motor Filter
Lock ‘n Seal™ Lever
Handle Release
Pedal
Headlight
Foot
Window
Height Adjustment
Knob
Scuff Resistant Bumper
Wide Cleaning Foot
4
Curved
Hose
Wand
www.bissell.com
Hose
Wand
Base
CAUTION
:
Do not plug in your
Assembly
vacuum cleaner until
you are familiar with
all instructions and
operating procedures.
The only tool you’ll need to assemble your
vacuum cleaner is a Phillips screwdriver.
Attach handle to vacuum
1.
Locate the handle and cord wrap. Remove
the screw packet taped to the handle.
2.
Stand the vacuum upright and from the rear of the unit, slide the base of the handle
firmly into the grooves at the top of the
vacuum body.
3.
IMPORTANT – before inserting the screws
into the handle, slide the cord wrap into the
handle.
4.
Ensure that the handle and cord wrap are
firmly fit to the vacuum body. If there are
any gaps, continue to push firmly until the
handle and cord wrap are flush.
5.
Insert 2 of the screws provided (3 total)
into the existing holes, attaching the cord
wrap and handle to the body of the vacuum.
Tighten securely with a screwdriver.
6.
Attach the hose and cord clip by snapping
it into the handle of the unit. Secure it by
inserting the screw provided.
7.
Attach the lower hose clip by snapping it into place and twisting to the right.
2.
3.
6.
7.
Warning
:
Plastic film can be
Hose Clip
www.bissell.com
dangerous. To avoid
danger of suffocation,
keep away from babies
and children.
5
Assembly
1.
Twist 'n
Snap Hose
Attach vacuum hose and tools
1.
Line up the tabs on the base of the Twist ‘n
Snap hose with the corresponding notches
on the hose collar as shown.
2.
Turn the Twist ‘n Snap hose to the left to lock the hose into place.
3.
Connect the curved hose wand to the hose.
Grasping the curved hose wand, slide the
end of the curved hose wand onto the hose
wand base. Snap the hose into the hose clip.
NOTE: The vacuum will not operate effectively
unless the curved hose wand is firmly attached.
4.
Slide the extension wand and crevice tool
together into the storage clip.
5.
Slide the dusting brush/upholstery tool into
the storage clip.
6.
Attach the Pet TurboBrush by snapping it
onto the top cap of the upper tank as shown.
Operation
Power switch
The power switch is located just below the
handle on the front of the vacuum. Push the
rocker switch “ON” (I) to vacuum, and “OFF” (O)
when cleaning is complete.
6.
CAUTION:
Before using your vacuum,
make sure that the dirt
container is in the locked
position and that all filters
(pre-motor and HEPA postmotor) are in place. Do not
operate your vacuum
without these filters.
NOTICE:
For above floor cleaning, the floor
brush will continue to rotate but
is raised above floor. To prevent
carpet damage, do not lean on
the vacuum or let the powerfoot
tilt forward.
CAUTION:
To avoid personal injury
and to prevent the cleaner
from falling when cleaning
stairs, always place it at
the bottom of the stairs.
6
www.bissell.com
1.
Operation
2.
Handle positions
3.
Press the handle release pedal, located on the
lower left side of the vacuum, with your foot to
place your vacuum into one of three cleaning
positions.
1. Upright – For storage and above floor cleaning with tools.
2.Normal Cleaning – Press handle release
pedal once. Position used for most household floor cleaning tasks.
Tip:
Before cleaning under low furniture, check
3.Low Cleaning – With the vacuum in normal area first for objects that might harm the unit
cleaning position, press handle release pedal
or block the vacuum hose.
again. Use for reaching under low furniture
such as tables, chairs or beds.
Height adjustment
The powerfoot/rotating floor brush on your
vacuum can be adjusted to clean several floor
surfaces
NOTE: For optimal cleaning performance,
adjust to the lowest practical setting. If
your cleaner is difficult to push, adjust to
the next higher setting.
1.
1.
Turn height adjustment knob to desired setting.
Bare Floor
For non-carpeted, indoor surfaces
Lowest Setting
For short pile carpets
Medium Setting For short and medium pile carpets
Highest Setting
For plush pile carpet
Transporting cleaner
1.
To move your cleaner from room to room,
put the handle in the upright position, tilt the
cleaner back on its rear wheels and push
forward.
2.
The cleaner can also be moved by using the
carry handle.
www.bissell.com
2a.
right way to carry
2b.
wrong way to carry
7
Operation
Clean filter indicator
The clean filter indicator tells you when the airflow
in your vacuum is reduced due to dirty filters or a
clog in the hose. The clean filter indicator will remain
green while the unit is running until the airflow is
reduced by a clog or dirty filter. At that time, it begins
to change to red or black. When it is fully red, the
airflow is significantly reduced or clogged by a dirty
filter. Follow the steps on page 11 to clean your
filters. All filters in the vacuum should be cleaned or
replaced when the clean filter indicator turns red.
If the indicator turns black, it means you have a clog
in your hose. To check and remove the clog, remove
the hose from the unit by turning the Twist ‘n Snap
hose to the right. Try to visually locate the clog. Once
you have done this, use a blunt long object such as a
broom handle to loosen and remove the debris. Once
this is completed, reassemble the hose to the unit,
If the indicator remains red or black with the
vacuum running, follow the steps on page 15 to
check for and clear clogs.
NOTE: When your vacuum is turned off,
the clean filter indicator will go to the red
color setting. The clean filter indicator
only detects reductions in airflow when
the vacuum power is on.
Clean
Filter
Indicator
NOTICE:
While vacuuming, certain carpets
and low humidity conditions may
generate small static discharges.
The discharges are entirely
harmless and are not associated
in any way with the main
power supply.
Dusting Brush/
Upholstery Tool
Special on-board tools
Your vacuum is not only a powerful carpet and
rug cleaner, it’s also a versatile above floor
Crevice Tool
vacuum cleaner when you select one of the
special tools.
Extension Wand
1. Raise the handle to the upright position.
2.
3.
Grasp the curved hose wand handle to
separate from hose wand base.
Curved Hose Attach tools by firmly pushing onto vacuum Wand
hose, curved hose wand or extension
wand. They are a friction fit, so be sure the
hose and tool fit snuggly together.
Dusting Brush/Upholstery Tool: Two types of
cleaning tools in one attachment.
• Use the dusting brush to dust Hose Wand Base
furniture, blinds, books, lamps,
shelves and baseboards.
• Slide the brush off to use the upholstery tool on cushions, draperies and fabrics.
8
www.bissell.com
Operation
Crevice Tool: Use in tight narrow spaces. Extension Wand: Use with desired attachment for
a longer reach.
Curved Hose Wand: Use with desired attachment
for a longer reach or for cleaning hard to
reach places.
Pet TurboBrush™: (Select Models only)
Use rotating brush action for cleaning and
removing pet hair from stairs, upholstery, area
rugs and other small areas.
1. Attach to the end of the hose or extension wand.
2.
Pull toward you in a raking motion. Press gently
when using the Pet TurboBrush to gain maximum
cleaning. Too much pressure could damage the pet
hair grabbers or cause the brush to stop rotating.
NOTE: This tool is designed to remove pet
hair from upholstered or carpeted surfaces.
It should not be used on pets.
Power cord usage
1.
To use your vacuum, remove the cord and plug
it into an electrical outlet. For your convenience,
there are two quick release cord wraps for easy
cord removal. There is also a cord clip that is
part of the upper cord wrap where you can
attach the cord when vacuuming.
2.
When you are finished cleaning, turn vacuum cleaner off.
3.
Unplug power cord by grasping the plug (NOT
the cord) and disconnect from outlet.
4.
Loop power cord around cord wraps on rear
of vacuum cleaner. Be sure to first return the
quick release cord wraps back to their original position before wrapping the cord.
5.
Clip molded plug to power cord to secure.
Quick Release
Cord Wrap
www.bissell.com
NOTICE:
For above floor cleaning, the floor
brush will continue to rotate but
is raised above floor. To prevent
carpet damage, do not lean on
the vacuum or let the powerfoot
tilt forward.
CAUTION:
The rotating floor brush
continues to rotate while
tools are in use. To reduce
the risk of injury from
moving parts, always
move the cleaner with the
carrying handle. Always
place vacuum cleaner
on the floor with handle
in upright position when
using tools. Never place
your fingers under the
cleaner when it is
running. Never place
powerfoot on furniture or
uneven surfaces. Do not
place vacuum cleaner
close enough to objects
to pull them into the
rotating floor brush.
9
Maintenance and care
To maximize your cleaning performance and
extend the life of your vacuum, it is very
important that you empty your dirt container
and check and clean your filters frequently.
Perform the following maintenance steps:
1. Empty the dirt container when the dirt reaches
the “Full” line on the container, or more frequently
to prevent overfills. For best performance, empty
after each use.
W
ARNING:
To reduce the risk of electric
shock, turn power switch OFF
and disconnect plug from
electrical outlet before
performing maintenance or
troubleshooting checks.
2. Check the pre-motor filter and post-motor HEPA
media filter at least once a month and clean or
replace as needed.
NOTE: Be sure to clean or replace your
filters anytime the clean filter indicator
(select models only) begins to turn red.
3. Replace the post-motor HEPA media filter
Tip:
To maximize cleaning performance, check
and clean or replace all filters as suggested.
every three to six months.
NOTE: More frequent filter cleaning may be
necessary if you are vacuuming new carpet,
fine dust, or have allergy concerns. Follow
the instructions on the following pages to
perform these simple maintenance steps.
Empty dirt container
The dirt container needs to be emptied when the
dirt reaches the “Full” line on the container.
1. Unplug the vacuum from electrical outlet
3.
2. Slide the Lock ‘n Seal Lever to the “Unlock”
position.
3. Grasp handle and pull the dirt container
straight out to remove from the vacuum.
Unlock
4. Empty dirt into garbage container.
NOTE: Emptying the dirt container after
every use will help prevent over filling and
ensure that the vacuum is ready to go the
next time you clean.
4.
10
www.bissell.com
Maintenance and care
Cleaning the pre-motor filter and replacing the post-motor HEPA media filter
1. Unplug the vacuum from electrical outlet.
2. The pre-motor filter protects the motor
from dirt particles. It is located in the
slide out tray underneath the dirt container. If the filter becomes dirty, pull
out the tray, lift out the foam filter pad
and clean it.
NOTE: The pre-motor filter may be
hand washed in cold water with mild
detergent. Rinse well and air dry
Washable
thoroughly before replacing.
Pre-Motor
3. The post-motor HEPA media filter
assists in the filtration process to return clean air to the room. It is located behind the door on the side of the vacuum. If the filter becomes
dirty, open the door, remove the filter
and replace.
NOTE: The post-motor filter is a
white, pleated HEPA media filter. This
filter is NOT washable and must be
replaced when it becomes dirty.
Post-Motor
HEPA Media Filter
Filter
W
ARNING:
Do not operate vacuum
cleaner with damp or wet
filters or without all filters
in place.
www.bissell.com
11
Maintenance and care
Check rotating floor brush and drive belt
You should check your vacuum cleaners
rotating floor brush and drive belt regularly
for wear or damage. You should also clean
the brush and brush ends of strings, hair
and carpet fibers. This type of debris can
wrap around the brush and hamper its
ability to effectively clean your carpet. Also
remove any debris that has accumulated
under the brush cover.
1. Unplug the vacuum from electrical outlet.
2. Place handle in low position and turn
vacuum cleaner over so bottom side is
facing up.
3. Remove the screws marked 1 and 2.
Release the latches marked 3 and 4. Lift
off the brush cover.
W
ARNING:
To reduce the risk of injury
from moving parts, turn
power switch off and
disconnect plug from
electrical outlet.
6.
1
3
4
2
4. Grasp rotating floor brush at both ends
and lift.
5. Clean strings, hair and other debris from
rotating floor brush, paying particular
attention to brush ends.
6. Clean strings, hair and other debris from
motor pulley and drive belt areas.
7. Check drive belt carefully for wear, cuts or
stressed areas. Motor Pulley
8. Check air passageway for obstructions.
Remove debris from this area. Air Passageway
12
www.bissell.com
Maintenance and care
Replace drive belt
1. Unplug the vacuum from electrical outlet.
2. With rotating floor brush removed from
vacuum cleaner (Steps 1-4 of check
rotating floor brush and drive belt),
grasp old drive belt and remove from
motor pulley. Discard the old drive belt.
3. Place new drive belt over motor pulley
3.
and loop other end over rotating floor
Motor Pulley
brush in the space between the bristles.
NOTE: It is important that you use only
genuine BISSELL replacement belts.
Generic belts may not meet the exact
specifications required to keep your
vacuum operating at its peak performance.
The use of unbranded belts could lead to
early failure of the vacuum and could void
your warranty.
4. Pull the rotating floor brush firmly into
position, stretching the drive belt and
placing ends of rotating floor brush
down into the slots on sides. Alignment
of brush ends in slots may be necessary
to fully insert the brush.
6.
1
3
5. Turn rotating floor brush by hand several
times in the direction of motor pulley. If
properly installed, drive belt will center
itself on rotating brush crown.
2
4
6. Insert front edge of brush cover, rotate
into place, snap two latches and replace
two screws.
Replace lightbulb
2.
1. Unplug the vacuum from electrical outlet.
2. Using a flat bladed screwdriver, pry the tab
on the left and right side out and pull out to
remove the lens.
3.
4.
Remove the bulb from the socket by grasping the bulb and pulling gently. Install
the new bulb by pushing it gently into the
socket until the bulb snaps into place.
3.
4.
Reposition the lens and snap it back into place.
www.bissell.com
13
Maintenance and care
Maintaining Pet TurboBrush
The Pet TurboBrush should be checked regularly
for clogs or debris wrapping around the brush.
1. Unplug the vacuum from electrical outlet.
14
2.
If a clog is present or debris is visible, unscrew
the two screws on the back of the Pet
TurboBrush to remove the faceplate and clear
any obstructions.
3.
To clean debris from the brush, remove the
brush from the drive belt and clean debris.
4.
Reposition the drive belt on the brush. Place ends of brush in slots on sides as
shown. Reposition faceplate and secure with
two screws.
www.bissell.com
2.
4.
Maintenance and care
Clearing clogs
Tip:
Low suction or poor pickup may be due to a clog
in the vacuum cleaner. If you notice a change in
Hair, string and small objects can block
the sound of the motor, check for clogs.
the
vacuum hose or tools. Check them
1. Unplug the vacuum from electrical outlet.
occasionally for obstructions.
2.
Empty dirt container.
3.
Check upper tank for build up or clogs.
4.
If you notice a clog in the upper tank,
remove the separator plate (see section
"Cleaning the Upper Tank" on page 16). 5.
Grasp the curved wand and separate it from
the hose wand base. Check for a clog in the
base, the wand or in the hose.
4.
NOTE: On select units that have the clean
filter indicator, when the indicator reads
black, there is a clog in the hose which is
diminishing suction power. Remove the clog
in the hose to restore full suction power.
6.
Remove the Twist ‘n Snap hose from the vacuum
by turning to the right. Straighten the hose and
unclog with a long, narrow object.
7.
If you notice debris or dirt clogged in the connecting tube, remove it by pulling it out at the
top and lifting the tube out. Clean the tube of any
debris and clear any possible clog from the port to the pre-motor filter. Reattach tube by first
installing the base and then push in the top of
the tube.
8.
If the clog persists, follow the instructions for
checking the rotating floor brush and drive
belt on page 12 and inspect the air passageway for obstructions.
2.
5.
Connecting Tube
Hose Wand Base
Bottom Port
www.bissell.com
15
Maintenance and care
Cleaning the upper tank
1.
1. Grasp the inner cyclone and twist to the left
or to the unlocked marking, until the locking
tabs stop the rotation. Pull down from the
upper tank to remove it.
2. Wipe out the inside of the upper tank and the
inner cyclone with a damp cloth moistened
with water or a mild cleaning solution.
3. If you desire to thoroughly clean the louvers
located in the upper portion of the inner
cyclone, hold the bottom of the cyclone and
gently pull straight up on the louvers.
3.
4. The inner cyclone and louvers may be
washed using a mild detergent. Be sure they are completely dry before reassembling or
damage to your unit may result.
5. Once cleaning is completed, reassemble the
louvers over the inner cyclone by sliding it straight down on the top of the
inner cyclone. Be sure to line up the tabs
when reassembling for proper installation.
5.
6. To replace the inner cyclone, slide it into
the upper housing. Be sure to line up the
inner cyclone by having the marking (Front)
positioned toward the front of the unit. Push
the inner cyclone in and rotate it to the right
or locked marking until the locking tabs stop
the rotation.
16
www.bissell.com
6.
Troubleshooting
Vacuum cleaner won’t run
WARNING:
To reduce the risk of electric shock,
turn power switch OFF and
disconnect plug from electrical
outlet before performing
maintenance or troubleshooting.
Possible causes
Remedies
1. Power cord not plugged in
1. Check electrical plug
Vacuum cleaner and tools won’t pick up dirt
Possible causes
Remedies
1. Incorrect height adjustment
1. Adjust powerfoot to correct height
2. Hose not attached to suction opening
2. Firmly push curved hose wand into hose wand base
3. Twist 'n Snap hose not securely attached
3. Make sure Twist 'n Snap hose is snapped into locked position
4. Crack or hole in hose
4. Check hose and replace if needed
5. Broken or worn drive belt
5. Replace drive belt, see pages 12-13 6. Rotating floor brush bristles worn
6. Replace brush
7. Rotating floor brush jammed
7. Remove brush and clean debris from brush ends
8. Clog in vacuum
8. Clear clogs, see page 15
9. Dirt container full
9. Empty dirt container
10. Dirt container not installed properly
10.Position correctly and lock in place
11. Filters are dirty
11.Check and clean or replace pre-motor and post-motor filters
12. Pet TurboBrush is clogged or debris is wrapped
around the brush roll
12.Check Pet TurboBrush, see page 14
Vacuum cleaner is difficult to push
Possible causes
Remedies
1. Incorrect height setting
1. Adjust powerfoot to correct height setting
Visible dirt escaping from cleaner
Possible causes
Remedies
1. Dirt container full
1. Empty dirt container
2. Filters missing or installed incorrectly
2. Check pre-motor and post-motor filters for correct installation
3. Dirt container installed incorrectly
3. Pull out and re-insert dirt container correctly
Other maintenance or service not included in the manual should be performed by an
authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
www.bissell.com
17
BISSELL Consumer Services
If your BISSELL product should require service:
In the UK, Australia or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you
the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in
country distributor for questions, service, or repair.
If you have questions about your warranty or need replacement parts please contact the numbers below.
For UK inquiries:
Monday - Thursday 9 am — 5 pm
Friday 9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
The Boat Yard
105 Straight Road
Old Windsor
Berkshire, SL4 2SE
United Kingdom
Telephone: 0870-225-0109
For Australian inquiries:
Monday - Friday 9 am — 5 pm
BISSELL Australia PTY LIMITED
Unit 35
15 Ricketts Road
Mount Waverley, Victoria 3149
Australia
Telephone: 1-800-811-183
For New Zealand inquiries:
Monday - Friday 9 am — 5 pm
Parex Industries Ltd.
103 Central Park Drive
Henderson
Auckland
New Zealand
Telephone: 0800-247-735
For all other inquiries:
Monday - Friday 8 am — 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, MI 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
18
www.bissell.com
Replacement parts
ItemPart No.Part Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
32074Style 7/9/10/12/14 Drive Belt (2-Pack)
203-1297Headlight Bulb
203-1063
Crevice Tool
203-1228
Dusting Brush/Upholstery Tool
203-1399
Pet TurboBrush
203-1022Extension Wand
203-2303
Curved Hose Wand
203-2304
Twist 'n Snap Vacuum Hose (clear)
203-2305
Wide Window Foot Brush Roll (gray)
3290Style 7/8/14 Pre-Motor Foam Filter
3091Style 8/14 HEPA Media POST-Motor Filter
203-2306Hose & Cord Wrap
203-2307
Cord Clip
203-2308Hose Clip
1
2
3
4
5
6
7
8
9
10
11
12
13
14
www.bissell.com
19
Warranty - BISSELL Twin Power Dual Cyclonic Bagless Vacuum
This warranty gives you specific legal rights, and you may also have other rights which may vary from country
to country. If you need additional instruction regarding this warranty or have questions regarding what it may
cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or
contact your local in country distributor.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., will replace (with
new or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the
original purchaser, for one year any defective or malfunctioning part do to manufacturers defect.
This warranty applies to product used for personal, and not commercial or rental service. This warranty does
not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction
caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.
For UK inquiries:
Monday - Thursday 9 am — 5 pm
Friday 9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
The Boat Yard
105 Straight Road
Old Windsor
Berkshire, SL4 2SE
United Kingdom
Telephone: 0870-225-0109
For Australian inquiries:
Monday - Friday 9 am — 5 pm
BISSELL Australia PTY LIMITED
Unit 35
15 Ricketts Road
Mount Waverley, Victoria 3149
Australia
Telephone: 1-800-811-183
For New Zealand inquiries:
Monday - Friday 9 am — 5 pm
Parex Industries Ltd.
103 Central Park Drive
Henderson
Auckland
New Zealand
Telephone: 0800-247-735
For all other inquiries:
Monday - Friday 8 am — 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, MI 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT.
BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES
EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE
BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS
DESCRIBED ABOVE.
20
www.bissell.com
©2007 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 603-2378
Rev 8/07
Visit our website at:
www.bissell.com