Blodgett Mark V XCEL Specifications

mark v-100 xcel
convection oven
INSTALLATION - OPERATION - MAINTENANCE
(Formerly MARK V XCEL)
BLODGETT OVEN COMPANY
www.blodgett.com
44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone: (802) 658-6600 Fax: (802)864-0183
PN 36433 Rev Q (3/14)
© 2014 - G.S. Blodgett Corporation
Your Service Agency’s Address:
Model
Serial number
Oven installed by
Installation checked by
TABLE OF CONTENTS
IMPORTANT
WARNING: Improper installation, adjustment, alternation,
service or maintenance can
cause property damage, injury or death. Read the instllation, operation and maintenance instructions thoroughly
before installing or servicing
this equipment.
FOR YOUR SAFETY
Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or any
other appliance.
The information contained in this
manual is important for the proper installation, use, and maintenance of this oven. Adherence
to these procedures and instructions will result in satisfactory
baking results and long, trouble free service. Please read
this manual carefully and retain
it for future reference.
ERRORS: Descriptive, typographic or pictorial errors are
subject to correction. Specifications are subject to change
without notice.
INSTALLATION
Oven Description and Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Delivery and Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Oven Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Sanitation Bolts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Leg Attachment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Caster Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Double Section Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Oven Leveling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Utility Connections - Standards and Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Initial Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OPERATION
Safety Information.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Solid State Manual Control.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Solid State Digital Control.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CH-Pro3 (Solid State Programmable Digital Control). . . . . . . . . . . . . . . . . . . . . . . . 17
Blodgett IQ2™ Vision Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SmartTouch Touchscreen Control.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
How Cook & Hold Works.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
General Guidelines for Operating Personnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Suggested Times and Temperatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
MAINTENANCE
Cleaning and Preventative Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installation
Oven Description and Specifications
Cooking in a convection oven differs from cooking in a
conventional deck or range oven since heated air is constantly recirculated over the product by a fan in an enclosed chamber. The moving air continually strips away
the layer of cool air surrounding the product, quickly allowing the heat to penetrate. The result is a high quality product, cooked at a lower temperature in a shorter
amount of time.
Blodgett convection ovens represent the latest advancement in energy efficiency, reliability, and ease of operation. Heat normally lost, is recirculated within the cooking
chamber before being vented from the oven: resulting in
substantial reductions in energy consumption and enhanced oven performance.
Air Flow Pattern for Mark V-100 XCEL
Figure 1
voltage
hz
kW
U.S. and Canadian installations
208
60
11.0
208
60
11.0
220-240
60
11.0
220-240
60
11.0
440
60
11.0
480
60
11.0
General Export installations
220-240
50
11.0
220/380
50
11.0
240/415
50
11.0
230/400
50
11.0
electrical ratings- MKV1XL/AA
max load (amps
Phase
L1
L2
L3
N
Motor
1
3
1
3
3
3
53
33
50
28
16
15
—
28
—
23
13
12
53
33
50
28
16
15
—
—
—
—
—
—
6 AWG
8 AWG
6 AWG
8 AWG
12 AWG
12 AWG
1
3
3
3
50
17
19
19
—
15
14
14
50
15
14
14
—
4
5
5
Size per local code
Size per local code
Size per local code
Size per local code
2
Installation
Delivery and Location
Delivery and inspection
It is essential that an adequate air supply to the oven be
maintained to provide a sufficient flow of combustion and
ventilation air.
All Blodgett ovens are shipped in containers to prevent
damage. Upon delivery of your new oven:
•
Place the oven in an area that is free of drafts.
•
Inspect the shipping container for external damage.
Any evidence of damage should be noted on the
delivery receipt which must be signed by the driver.
•
Keep the oven area free and clear of all combustibles such as paper, cardboard, and flammable
liquids and solvents.
•
Uncrate the oven and check for internal damage.
Carriers will accept claims for concealed damage if
notified within fifteen days of delivery and the shipping container is retained for inspection.
•
Do not place the oven on a curb base or seal to
a wall. This will restrict the flow of air and prevent
proper ventilation. Tripping of the blower motor’s
thermal overload device is caused by an excessive
ambient temperature on the right side of the oven.
This condition must be corrected to prevent permanent damage to the oven.
The Blodgett Oven Company cannot assume responsibility for loss or damage suffered in transit. The carrier assumed full responsibility for delivery in good order when
the shipment was accepted. We are, however, prepared
to assist you if filing a claim is necessary.
Before making any utility connections to this oven, check
the rating plate to be sure the oven specifications are
compatible with the electrical services supplied for the
oven.
oven location
The well planned and proper placement of your oven will
result in long term operator convenience and satisfactory
performance.
1. Pull out control panel. The rating plate attached to the
inside of the control compartment.
The following clearances must be maintained between
the oven and any combustible or non-combustible construction.
•
Oven body right side - 0” (0 cm)
•
Oven body left side - 0” (0 cm)
•
Oven body back - 0” (0 cm)
•
Oven body bottom - 1/2” (1.2 cm)
The following clearances must be available for servicing.
•
Oven body sides - 12” (30 cm)
•
Oven body back - 12” (30 cm)
3
Installation
Oven Assembly
Sanitation Bolts
These bolts are required by NSF to block any exposed
hole on the back of an oven. This includes:
1. Locate the 5/16” bolts that were shipped with the
oven.
•
any unit, single or stacked, without a back panel.
2. Install the bolts as shown.
•
any holes in stacked units not used for mounting
stacking brackets.
Double Stacked Units
Units without back panels
Figure 2
4
Installation
Oven Assembly
Leg Attachment
Caster Assembly
1. Lay the oven on its back.
NOTE: Install the locking casters on the front of the
oven. Install the non-locking casters on the back
of the oven.
2. Align the threaded stud in each leg with the nut located inside each bottom corner of the oven frame. Turn
the legs clockwise and tighten to the nearest full turn.
Casters for Single and Double Stacked Ovens:
1. Attach the legs as described.
3. Align the two leg plate holes in each leg with those
in the oven bottom. Secure each leg using two 1/2”
bolts.
2. Pry the adjustable feet out of the legs
3. Insert one caster into each leg as shown. Tighten the
lock nuts to secure the casters.
NOTE: If using casters see CASTER ASSEMBLY
before proceeding.
4. Level the oven by screwing the adjustable leg feet in
or out as necessary.
Adjustable
Leg Foot
Caster Assembly
25” (64 cm) Legs Shown
Figure 4
Low Profile Casters for Double Stacked Ovens:
1. Align the three holes in each caster assembly plate
with those in the oven bottom. Secure each caster
using three 1/2” bolts.
6” (15 cm) Legs Shown
Figure 3
Figure 5
5
Installation
Oven Assembly
Double Section Assembly
Oven Leveling
1. Secure the short legs to the bottom sections as described.
After assembly, the oven should be leveled and moved to
the operating location.
2. Attach lower flue box to lower oven.
1. The oven can be leveled by adjusting the feet or casters located on the bottom of each leg.
3. Place the upper section in position on top of the lower
oven.
4. Attach the stacking brackets using the remaining
5/16” bolts shipped with the ovens.
5. Install flue riser and attach upper flue box to upper
oven.
WARNING!!
When stacking ovens be sure to remove the
single oven flue boxes prior to attaching upper and lower boxes and riser.
Flue
Boxes
Flue Riser
Figure 6
6
Installation
Utility Connections - Standards and Codes
THE INSTALLATION INSTRUCTIONS CONTAINED
HEREIN ARE FOR THE USE OF QUALIFIED INSTALLATION AND SERVICE PERSONNEL ONLY. INSTALLATION OR SERVICE BY OTHER THAN QUALIFIED
PERSONNEL MAY RESULT IN DAMAGE TO THE OVEN
AND/OR INJURY TO THE OPERATOR.
U.S. and Canadian installations
Qualified installation personnel are individuals, a firm,
a corporation, or a company which either in person or
through a representative are engaged in, and responsible
for:
The ventilation of this oven should be in accordance with
local codes. In the absence of local codes, refer to the
National ventilation code titled, “Standard for the Installation of Equipment for the Removal of Smoke and Grease
Laden Vapors from Commercial Cooking Equipment”,
NFPA-96-Latest Edition.
•
All ovens, when installed, must be electrically grounded
in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA
70-Latest Edition and/or Canadian National Electric Code
C22.2 as applicable.
the installation of electrical wiring from the electric
meter, main control box or service outlet to the electric appliance.
Appliance is to be installed with backflow prevention in
accordance with applicable federal, province and local
codes.
Qualified installation personnel must be experienced in
such work, familiar with all precautions required, and have
complied with all requirements of state or local authorities
having jurisdiction.
General export installations
Installation must conform with Local and National installation standards. Local installation codes and/or requirements may vary. If you have any questions regarding the
proper installation and/or operation of your Blodgett oven,
please contact your local distributor. If you do not have a
local distributor, please call the Blodgett Oven Company
at 0011-802-658-6600.
7
Installation
Electrical Connection
Wiring diagrams are located in the control compartment
and on the back of the oven.
4. Connect the supply wires to top of right contactor in
the control compartment at the lower right corner of
the oven.
The electric motor, indicator lights and related switches
are connected to the oven as follows:
5. Reinstall the bottom trim and control panel covers.
1. Remove the bottom trim and control panel covers.
Slide the control panel forward.
NOTE: To prevent damage there is no power to the
heating elements when the blower is not operating.
2. Connect the supply conduit to the wire duct located
in the lower left hand corner on the back of the oven.
The Blodgett Oven Company cannot assume
responsibility for loss or damage suffered
as a result oF improper installATION.
3. Run the supply wires through the duct to the front of
the oven.
Install incoming
power on this
contactor
Figure 7
8
Installation
Initial Startup
Oven restraint
Adjustments associated with initial installation
If casters are used in conjunction with a power supply
cord for movable appliances, a fixed restraint should be
provided.
The restraint (ie: heavy gauge cable) should be attached
without damaging the building. DO NOT use the gas piping or electrical conduit for the attachment of the permanent end of the restraint! Use anchor bolts in concrete or
cement block. On wooden walls, drive hi test wood lag
screws into the studs of the wall.
Each oven, and its component parts, have been thoroughly tested and inspected prior to shipment. However, it is
often necessary to further test or adjust the oven as part
of a normal and proper installation. These adjustments
are the responsibility of the installer, or dealer. Since
these adjustments are not considered defects in material or workmanship, they are not covered by the Original
Equipment Warranty. They include, but are not limited to:
If the oven is moved from its regular location, the restraint
must be reconnected when the oven is returned.
•
calibration of the thermostat
•
adjustment of the doors
•
leveling
•
tightening of fasteners.
1. Mount the supplied bracket to the leg bolt just below
the power cord.
2. Attach the clip on restraining cable to the mounting
bracket.
No installation should be considered complete without
proper inspection, and if necessary, adjustment by qualified installation or service personnel.
Back of Oven
Restraint Cable
Bracket
Double stacked unit shown. Use the same
procedure for single units.
Figure 8
9
Operation
Safety Information
The information contained in this section is provided for
the use of qualified operating personnel. Qualified operating personnel are those who have carefully read the information contained in this manual, are familiar with the
functions of the oven and/or have had previous experience with the operation of the equipment described. Adherence to the procedures recommended herein will assure the achievement of optimum performance and long,
trouble-free service.
SAFETY TIPS
For your safety read before operating
General safety tips:
Please take the time to read the following safety and operating instructions. They are the key to the successful
operation of your Blodgett oven.
10
•
If the oven needs to be moved for any reason, the
supply cord must be disconnected from the unit
before removing the restraint cable. Reconnect the
restraint after the oven has been returned to its
original location.
•
DO NOT remove the control panel cover unless the
oven is unplugged.
Operation
Solid State Manual Control
control Description
1. SELECTOR SWITCH - controls power to the oven for
high fan, low fan or cool down.
2. OVEN READY LIGHT - when lit indicates elements
are heating. When the light goes out the oven has
reached operating temperature.
1
3. SOLID STATE THERMOSTAT - allows an infinite selection of temperatures from 150-550°F (66-288°C).
(infinite control shown)
4. TIMER - activates an electric buzzer that sounds
when the cook time expires.
2
5. LIGHTS SWITCH - controls interior lights.
6. CIRCUIT BREAKER SWITCH - controls power to the
oven.
3
operation
1. Turn the SELECTOR Switch (1) to either HIGH FAN
or LOW FAN. The blower and control compartment
cooling fan operate and are controlled automatically
by the action of the doors.
4
2. Set the SOLID STATE THERMOSTAT (3) to the desired setting or temperature.
3. Preheat until the OVEN READY LIGHT (2) goes out.
4. Load product into the oven. Determine cook time and
set the TIMER (4).
5
5. When the buzzer sounds, remove the product from
the oven. Turn the TIMER knob (4) to OFF to silence
the buzzer.
6. Turn the SELECTOR Switch (1) to OVEN OFF.
Oven Cool Down:
1. Turn the SELECTOR Switch (1) to COOL DOWN.
NOTE: The doors may be opened to speed the
cooling process.
6
Oven Shut Down:
1. Turn the SELECTOR SWITCH (1) to OVEN OFF.
Figure 9
11
Operation
Solid State Digital Control
control Description
1. SELECTOR SWITCH - turns power to the oven on
or off. Allows selection of Cook or Cool Down Modes
and fan speed (if applicable).
1
2. DISPLAY - displays time or temperature and other information related to oven function.
3. HEAT LAMP - lights when heater is on.
4. PULSE LAMP - lights when Pulsed Fan Mode is
turned on.
5. HOLD LAMP - lights when Hold Mode is turned on.
2
6. DIAL - used to enter set points in display
4
7. START/STOP KEY - starts or stops the timer.
8. TIME KEY - used to show time in the display.
3
5
9. TEMP KEY - used to show set temperature in the display.
NOTE: Actual temperature is shown while the
TEMP key is held down.
6
8
10. HOLD KEY - turns Hold Mode on or off.
7
9
10
11
11. PULSE KEY - turns Pulse Mode on or off.
12. LIGHTS SWITCH - controls interior lights.
13. CIRCUIT BREAKER SWITCH - controls power to the
oven.
Programming
To set the cook temperature:
12
1. Press TEMP (9) key.
2. Rotate dial (6) to enter temperature.
To set the cook time:
1. Press TIME (8) key.
2. Rotate the dial (6) to enter time.
NOTE: Time is entered in hours:minutes (0:00) or
minutes:seconds (00:00).
13
To set the hold time:
1. Press HOLD key (10) to turn hold mode on.
NOTE: HOLD light is on.
2. Rotate dial (6) to enter the hold temperature.
3. Press START/STOP key (7)
Figure 10
12
Operation
Solid State Digital Control
To set the pulse time:
Cook with Pulse:
1. Press PULSE KEY (11) to turn pulse mode on.
NOTE: PULSE light is on when pulse mode is on and off
when pulse mode is off.
NOTE: Pulse light is on.
1. Turn the SELECTOR SWITCH (1) to the desired position.
2. Rotate DIAL (6) to enter the pulse time. Pulse time is
a portion of the pre-set cook time.
2. Enter cook time and cook temperature.
operation
3. Press PULSE KEY (11). Enter the pulse time. A minimum of one minute must be entered to operate.
Cook Only:
1. Turn SELECTOR switch (1) to the desired position.
NOTE: Pulse time is a portion of the cook time and
does not increase the previously entered
cook time.
2. Enter the cook time and temperature.
3. Load product into oven.
4. Load product into oven.
NOTE: The display reads LOAD with the oven is
near the set temperature.
NOTE: The display reads LOAD with the oven is
near the set temperature.
4. Press the START/STOP key (7). The timer begins to
count down.
5. Push START/STOP KEY (7). The timer begins to
count down the cook time. The oven will be in pulse
mode for the set pulse time. Once the set time has expired, the unit will automatically switch to cook mode
and continue counting down.
5. When the cook timer reaches 00:00 the buzzer
sounds and the display reads DONE.
6. Press the START/STOP key (7) to silence the buzzer.
7. Remove the product.
6. When the cook timer reaches 00:00 the buzzer
sounds and the display reads DONE.
Cook with Hold:
7. Push the START/STOP KEY (7) to turn the buzzer off.
NOTE: HOLD light is on when hold mode is on and off
when hold mode is off.
8. Remove the product.
1. Turn SELECTOR switch (1) to the desired position.
Oven Cool Down:
2. Enter the cook time and temperature.
1. Turn the SELECTOR Switch (1) to COOL DOWN.
NOTE: The doors may be opened to speed the
cooling process.
3. Press the HOLD key (10). Enter the hold temperature.
4. Load product into oven.
Oven Shut Down:
1. Turn the SELECTOR SWITCH (1) to OVEN OFF.
NOTE: The display reads LOAD with the oven is
near the set temperature.
5. Push the START/STOP (7) key. Timer begins to count
down.
6. When the cook timer reaches 00:00 the buzzer sounds
and the display reads DONE. The buzzer turns off after a few seconds. The display reads HOLD until the
oven reaches the hold temperature. Then the timer
begins to count up.
7. Push the START/STOP key (7) to stop timer.
8. Remove the product.
9. Push HOLD (10) key to turn off hold mode.
13
Operation
Solid State Digital Control with Humidaire
control Description
1. SELECTOR SWITCH - controls power to the oven for
high fan, low fan or cool down.
2. DISPLAY - displays time or temperature and other
information related to oven function.
1
3. HEAT LAMP - lights when heater is on.
4. PULSE LAMP - lights when Pulsed Fan Mode is
turned on.
5. HOLD LAMP - lights when Hold Mode is turned on.
6. DIAL - used to enter set points in display
2
7. START/STOP KEY - starts or stops the timer.
3
4
8. TIME KEY - used to show time in the display.
5
9. TEMP KEY - used to show set temperature in the
display.
NOTE: Actual temperature is shown while the
TEMP key is held down.
6
8
10. HOLD KEY - turns Hold Mode on or off.
11. PULSE KEY - turns Pulse Mode on or off.
7
9
10
11
12. LIGHTS SWITCH - controls interior lights.
13. HUMIDAIRE START SWITCH - activates moisture
injection for a preset period of 30 seconds.
14. HUMIDAIRE LAMP - lights when water is being injected
14
15. CIRCUIT BREAKER SWITCH - controls power to the
oven.
12
13
15
Figure 11
14
Operation
Solid State Digital Control with Humidaire
Programming
Cook with Hold:
To set the cook temperature:
NOTE: HOLD light is on when hold mode is on and off
when hold mode is off.
1. Press TEMP (9) key.
2. Rotate dial (6) to enter temperature.
1. Turn the SELECTOR switch (1) to the desired position.
To set the cook time:
2. Enter the cook time and temperature.
1. Press TIME (8) key.
3. Press the HOLD key (10). Enter the hold temperature.
2. Rotate the dial (6) to enter time.
4. Load product into the oven.
NOTE: Time is entered in hours:minutes (0:00) or
minutes:seconds (00:00).
NOTE: The display reads LOAD when the oven is
near the set temperature.
To set the hold time:
5. Push the START/STOP (7) key. Timer begins to count
down.
1. Press HOLD key (10) to turn hold mode on.
NOTE: HOLD light is on.
To set the pulse time:
6. When the cook timer reaches 00:00 the buzzer sounds
and the display reads DONE. The buzzer turns off after a few seconds. The display reads HOLD until the
oven reaches the hold temperature. Then the timer
begins to count up.
1. Press PULSE KEY (11) to turn pulse mode on.
7. Push the START/STOP key (7) to stop timer.
2. Rotate dial (6) to enter the hold temperature.
3. Press START/STOP key (7)
NOTE: Pulse light is on.
8. Remove the product.
2. Rotate DIAL (6) to enter the pulse time. Pulse time is
a portion of the pre-set cook time.
9. Push HOLD (10) key to turn off hold mode.
Cook with Pulse:
operation
Cook Only:
NOTE: PULSE light is on when pulse mode is on and off
when pulse mode is off.
1. Turn the SELECTOR switch (1) to the desired position.
1. Turn the SELECTOR SWITCH (1) to the desired position.
2. Enter the cook time and temperature.
2. Enter cook time and cook temperature.
3. Load product into the oven.
3. Press PULSE KEY (11). Enter the pulse time. A minimum of one minute must be entered to operate.
NOTE: The display reads LOAD when the oven is
near the set temperature.
NOTE: Pulse time is a portion of the cook time and
does not increase the previously entered
cook time.
4. Press the START/STOP key (7). The timer begins to
count down.
4. Load product into the oven.
5. When the cook timer reaches 00:00 the buzzer
sounds and the display reads DONE.
NOTE: The display reads LOAD when the oven is
near the set temperature.
6. Press the START/STOP key (7) to silence the buzzer.
7. Remove the product.
15
Operation
Solid State Digital Control with Humidaire
5. Push START/STOP KEY (7). The timer begins to
count down the cook time. The oven will be in pulse
mode for the set pulse time. Once the set time has expired, the unit will automatically switch to cook mode
and continue counting down.
The amount of water injected during the Humidaire cycle
may be adjusted as follows:
1. Check the pressure gauge on the back of the oven
while the water is dispensing. The pressure should be
no higher than 3 psi. If less moisture is desired, the
pressure can be set below 3 psi.
6. When the cook timer reaches 00:00 the buzzer
sounds and the display reads DONE.
2. To adjust the water pressure, loosen the locknut on
the pressure regulator.
7. Push the START/STOP KEY (7) to turn the buzzer off.
Turn the adjusting screw counter clockwise to decrease the water pressure.
8. Remove the product.
Oven Cool Down:
Turn the adjusting screw clockwise to increase the
water pressure if it is below 3 psi.
1. Turn the SELECTOR Switch (1) to COOL DOWN.
NOTE: Increasing the water pressure will increase
the amount of water injected during the
humidaire cycle. Decreasing the pressure
will decrease the water injected during the
humidaire cycle.
NOTE: The doors may be opened to speed the
cooling process.
Oven Shut Down:
1. Turn the SELECTOR SWITCH (1) to OVEN OFF.
The Humidaire Function:
3. Reset the locknut on the regulator.
Moisture may be injected into the oven cavity at any time
during the cook cycle.
4. Recheck the water pressure.
1. Press the HUMIDAIRE START SWITCH (13). Water
injects into the oven cavity for 30 seconds. After the
water stops injecting, the motor automatically turns
off for 30 seconds. This enables the moisture to saturate the product. Once the humidaire cycle is complete, the oven resumes normal operation.
WARNING!!
Setting the pressure above 3 psi will lead to
excessive water in the oven.
Water Pressure
Adjustment Screw
NOTE: The oven must be above 230°F (110°C) for
humidaire to operate.
Locknut
Rear view of oven
Figure 12
16
Operation
CH-Pro3 (Solid State Programmable Digital Control)
component Description
1. SELECTOR SWITCH - controls power to the oven for
high fan, low fan or cool down.
1
2. TIME DISPLAY - gives cook time.
3. TIME ARROW KEYS - press to enter cook and/or
pulse times.
4. READY INDICATOR - when lit indicates the oven has
reached the setpoint temperature and product may
be loaded.
2
5. TEMPERATURE DISPLAY - gives cook and hold
temperatures.
4
6. HEAT INDICATOR - when lit indicates the oven is
heating.
3
5
7. TEMPERATURE ARROW KEYS - press to enter
cook and hold temperatures.
7
6
8
9
11
13
8. HOLD KEY - turns hold mode on or off.
10
9. TEMP KEY - press to display actual oven temperature.
12
10. FAN KEY - turns pulse mode on or off. The LED
above the fan key is always on.
15
11. PRODUCT KEYS - three programmable keys.
12. MANUAL PRODUCT KEY - default product key used
for manual operation.
14
13. START KEY - press to begin a cook cycle.
14. PROGRAM KEY - press to enter programming mode
and save programmed settings.
16
15. STOP KEY - press to silence audible alarms and cancel cook cycles.
16. LIGHTS SWITCH - controls interior lights.
17. CIRCUIT BREAKER SWITCH - controls power to the
oven.
17
Figure 13
17
Operation
CH-Pro3 (Solid State Programmable Digital Control)
MANUAL operation
8. Press the STOP KEY (15) to stop the timer.
NOTE: Press the arrow keys to change the cook time
and temperature at any point duringmanual operation.
9. Remove the product.
Cook Only:
Cook with Pulse:
10. Push the HOLD KEY (8) to turn off hold mode.
1. Turn the SELECTOR SWITCH (1) to the desired position.
1. Turn the SELECTOR SWITCH (1) to the desired position.
2. Press the TIME ARROW KEYS (3) to enter the cook
time.
2. Press the TIME ARROW KEYS (3) to enter the cook
time.
3. Press the TEMPERATURE ARROW KEYS (7) to enter the cook temperature.
3. Press the TEMPERATURE ARROW KEYS (7) to enter the cook temperature.
4. The READY INDICATOR (4) lights when the oven is
at the set temperature. Load product into the oven.
4. Press the FAN KEY (10) for five seconds. The TEMPERATURE DISPLAY (5) goes blank. The fan key
LED flashes. Use the TIME ARROW KEYS (3) to enter the pulse time.
5. Press the START KEY (13). The TIME DISPLAY (2)
counts down. The manual key LED flashes.
NOTE: Pulse time is a portion of the cook time and
does not increase the previously entered
cook time.
6. When the cook time expires the LEDs and both displays flash and an audible alarm sounds. Press the
STOP KEY (15) to silence the alarm.
5. Press the FAN KEY (10) again. The TEMPERATURE
DISPLAY (5) lights.
7. Remove the product.
Cook with Hold:
6. The READY INDICATOR (4) in the temperature display lights when the oven is at the set temperature.
Load product into the oven.
1. Turn the SELECTOR SWITCH (1) to the desired position.
2. Press the TIME ARROW KEYS (3) to enter the cook
time.
7. Press the START KEY (13). The manual key LED
flashes. The TIME DISPLAY (2) counts down the
cook time. The fan cycles on for 30 seconds then off
for 30 seconds until the set pulse time has expired.
3. Press the TEMPERATURE ARROW KEYS (7) to enter the cook temperature.
8. When the pulse time expires both displays flash and
an audible alarm sounds. Press the STOP KEY (15)
to silence the alarm.
4. Press and hold the HOLD KEY (8) then release. Use
the TEMPERATURE ARROW KEYS (7) to enter the
hold temperature. The hold key LED lights. Press the
hold key again to exit the hold mode.
9. Remove the product.
Oven Cool Down:
5. The READY INDICATOR (4) lights when the oven is
at the set temperature. Load product into the oven.
1. Turn the SELECTOR Switch (1) to COOL DOWN.
6. Press the START KEY (13). The TIME DISPLAY (2)
counts down. The manual key LED flashes.
NOTE: The doors may be opened to speed the
cooling process.
Oven Shut Down:
7. When the cook time expires both displays flash and
an audible alarm sounds for several seconds then
self cancels. The hold key LED flashes. The time display begins to count up while the oven cools to the
hold temperature. When the oven reaches the hold
temperature the time display resets to 00:00 then begins to count up the hold time. The fan cycles with
heat demand in the hold mode.
1. Turn the SELECTOR SWITCH (1) to OVEN OFF.
18
Operation
CH-Pro3 (Solid State Programmable Digital Control)
programming the manual key default
programming the product keys
1. Turn the SELECTOR SWITCH (1) to the desired position.
1. Turn the SELECTOR SWITCH (1) to the desired position.
2. Press the MANUAL KEY (12). The manual and fan
key LEDs light.
2. Press the desired PRODUCT KEY (11). The product
and fan key LEDs light.
3. Press the TIME ARROW KEYS (3) to enter the cook
time.
3. Press and hold the PROGRAM KEY (14) until the corresponding LED flashes, approximately five seconds.
4. Press the TEMPERATURE ARROW KEYS (7) to enter the cook temperature.
4. Press the TIME ARROW KEYS (3) to enter the cook
time.
5. For Cook and Hold - Press and hold the HOLD KEY
(8). Use the TEMPERATURE ARROW KEYS (7) to
enter the hold temperature. The hold key LED lights.
Press the hold key again to exit the hold mode.
5. Press the TEMPERATURE ARROW KEYS (7) to enter the cook temperature.
6. For Cook and Hold - Press and hold the HOLD KEY
(8). Use the TEMPERATURE ARROW KEYS (7) to
enter the hold temperature. The hold key LED lights.
Press the hold key again to exit the hold mode.
For Cook with Pulse - Press the FAN KEY (10). Use
the TIME ARROW KEYS (3) to enter the pulse time.
If no pulse is required, leave pulse time at 0:00. The
fan key LED flashes. Press the fan key again to exit
fan mode.
For Cook with Pulse - Press the FAN KEY (10). Use
the TIME ARROW KEYS (3) to enter the pulse time.
If no pulse is required, leave pulse time at 0:00. The
fan key LED flashes. Press the fan key again to exit
the fan mode.
6. Press the PROGRAM KEY (14) to save the program
settings.
7. Press the PROGRAM KEY (14) to save the program
settings.
manual key default operation
1. Turn the SELECTOR SWITCH (1) to the desired position.
product key operation
2. Press the MANUAL KEY (12). The applicable LEDs
light.
1. Turn the SELECTOR SWITCH (1) to the desired position.
3. Press the START KEY (13). The TIME DISPLAY (2)
counts down. The manual key LED flashes.
2. Press the desired PRODUCT KEY (11). The applicable LEDs light.
NOTE: In Cook with Pulse the fan LED flashes.
3. Press the START KEY (13). The TIME DISPLAY (2)
counts down. The product key LED flashes.
NOTE: Press the arrow keys to change the cook
time and temperature at any point during
manual key operation.
NOTE: In Cook with Pulse the fan LED flashes.
4. When the cook time expires the applicable LEDs and
both displays flash and an audible alarm sounds.
4. When the cook or pulse time expires the applicable
LEDs and both displays flash and an audible alarm
sounds.
5. Press the STOP KEY (15) to silence the alarm.
5. Press the STOP KEY (15) to silence the alarm.
NOTE: In Cook & Hold the alarm self cancels. The
oven cools to the hold temperature and the
time display counts up.
NOTE: In Cook & Hold the alarm self cancels. The
oven cools to the hold temperature and the
time display counts up.
6. Remove the product.
6. Remove the product.
7. Turn the SELECTOR SWITCH (1) to OFF to shut
down the oven.
7. Turn the SELECTOR SWITCH (1) to OFF to shut
down the oven.
19
Operation
Blodgett IQ2™ Vision Control
component Description
1. OVEN POWER SWITCH - controls power to the oven.
1
2. DISPLAY - displays temperature and other controller
related information.
Mark V
XCEL
3. PROGRAM KEY - press to enter the programming
mode.
4. PROGRAM ARROW KEYS - use to move through
programming menus and options
2
4
3
7
5. HEAT LED - when lit indicates the control is calling
for heat.
6. PROG LED - when lit indicates the controller is in the
programming mode.
7. HIGH FAN LED - when lit indicates the fan is running
at high speed.
8
5
6
14
8. LOW FAN LED - when lit indicates the fan is running
at low speed.
9
9. SCAN KEY - Press to view time remaining on multiple
cook cycles and to review recipe programming.
10
10. COOL DOWN KEY - press to enter the cool down
mode.
11. TEMP/TOGGLE/CLEAR KEY - press during programming to toggle options.
11
15
12. HOLD KEY - press to enter hold mode.
13. SET BACK KEY -
12
14. PRODUCT KEYS (1-10) - assigns a key to a programmed recipe and begins a programmed cooking
process. Also used to enter numeric values in the programming mode.
16
13
15. PRODUCT LEDS - when lit indicate which product
keys are currently in use or programmed for the current oven temperature and fan speed.
16. SHELF KEYS (1-5) - assigns a shelf key.
DISCONNECT FROM THE SOURCE OF
SUPPLY BEFORE SERVICING
www.blodgett.com
Figure 14
20
Operation
Blodgett IQ2™ Vision Control
Oven Operation
Oven Startup:
NOTE: Press and hold the selected product key for
three seconds to cancel the cook cycle for
normal operation. To cancel the cook cycle
when using shelf timing, press and hold the
corresponding SHELF KEY (16) for 3 seconds.
1. Toggle the POWER SWITCH (1) to ON. The display
gives the software revision level. The oven preheats
to the lowest programmed first stage temperature.
The LEDS (15) for all products with the same first
stage temperature light.
4. When the cook time expires an alarm sounds and the
DISPLAY (2) reads:
Single Product Cooking Procedure:
NOTE: If the led next to the desired product key is lit
skip step 1.
DONE
Product name
1. Press the desired PRODUCT KEY (14). The oven
preheats to the first stage temperature for the selected product. When the oven reaches 10° of the preheat temperature an alarm sounds and the DISPLAY
(2) read:
5. Press the selected product key to silence the alarm.
Remove the product. If shelf timing is used, press the
flashing SHELF KEY (16) to silence the alarm.
LOAD
Multiple Batch Cooking Procedure:
This procedure is for single stage recipes with the same
cook temperature and fan speed only.
2. Load the product into the oven. Press the desired
PRODUCT KEY (14).
NOTE: If the led next to the first desired product key is lit
skip step 1.
3. If the shelf timing function is toggled to the on position for that product key, the DISPLAY (2) reads:
1. Press the first desired PRODUCT KEY (14). The
LEDS for all recipes with the same cook temperature
and fan speed will light.
PICK SHLF
The oven preheats to the cook temperature for the
selected product. When the oven reaches +10° of the
preheat temperature an alarm sounds and the DISPLAY (2) reads:
Press a SHELF KEY (16) to assign the product to that
shelf and start the cook cycle. Within five seconds,
the DISPLAY (2) scrolls the product name and shelf
number and counts down the remaining cook time.
LOAD
If the shelf timing function is toggled to the off
position for that product, pressing the product key
will start the cook cycle. The DISPLAY (2) scrolls the
product name and counts down the remaining cook
time.
NOTE: If the selected product has a cook time of
greater than 59:59 the DISPLAY (2) switches to hours:minutes.
NOTE: If the selected product is a single stage
recipe the LEDS for all single stage products with the same cook temperature and
fan speed will light. If the selected product
is a multiple stage recipe no other product
LEDS will light.
21
Operation
Blodgett IQ2™ Vision Control
2. Load the product into the oven. Press the desired
PRODUCT KEY (14).
6. Press the SHELF KEY (16) for the finished product
to silence the alarm. Remove the product. Close the
oven door. The DISPLAY (2) scrolls the product name
and counts down the remaining cook time for the
product with the least time remaining.
If the shelf timing function is toggled to the on position for that product key, the DISPLAY (2) reads
7. When the cook time expires an alarm sounds and the
display reads:
PICK SHLF
Press a SHELF KEY (16) to assign the product to that
shelf and start the cook cycle. Within five seconds,
the DISPLAY (2) scrolls the product name and shelf
number and counts down the remaining cook time.
DONE
8. Press the SHELF KEY (16) to silence the alarm. Remove the product.
If the shelf timing function is toggled to the off position
for that product, pressing the product key will start
the cook cycle. The DISPLAY (2) scrolls the product
name and counts down the remaining cook time.
Oven Cool Down:
1. Close the oven door. Press the COOL DOWN KEY
(10).
3. Load the second product. Press the desired PRODUCT KEY (14). the DISPLAY (2) reads
NOTE: Cool down cannot be activated with the
oven door open. Once the cool down cycle
has begun the doors may be opened to
speed the cooling process.
PICK SHLF
To Review Repipe Programming:
Press a SHELF KEY (16) to assign the product to that
shelf and start the cook cycle for product two.
1. Press the SCAN KEY (9). The display reads:
NOTE: Only products with lighted LEDS may be
selected.
RECIPE REVIEW
Select Product
Repeat step 3 for additional products.
4. The DISPLAY (2) scrolls the product name and counts
down the remaining cook time for the product with the
least time remaining.
The LEDs (15) for all previously programmed product
keys light. Press the PRODUCT KEY (14) you wish
to review. The display gives the recipe cook time for
stage 1. Use the PROGRAM ARROW KEYS (4) to
scroll through the recipe programming for the selected product key.
NOTE: To view the remaining cook time for the
other products press and hold the SCAN
KEY (9). The display cycles through the
remaining cook times for each product. Only
the led for the product with the cook time
displayed will be lit.
2. The control will exit recipe review after 30 seconds if
no key is pressed.
5. When a cook time expires an alarm sounds. The display reads
DONE
The led for the finished product lights. All other LEDS
are dark.
22
Operation
Blodgett IQ2™ Vision Control
product key Programming
To enter the product programming mode
To program the product
1. Press and hold the PROGRAM KEY (3). The DISPLAY (2) reads:
4. The display reads:
Shelf Cook
AAA
Prod Cnt
Programming
Definition: Shelf cook enables the operator to
reference product to one of the five shelf positions in the oven. At the end of a shelf cooking cycle the oven will display the name of the
product and the shelf number that is ready to
be pulled. Shelf cooking is not available for
multi-stage recipes.
Use the PROGRAM ARROW KEYS (4) to highlight
Programming. Press the PROGRAM KEY (3) to select. The display reads:
ENTER CODE
Use the PRODUCT KEYS (14) to enter the programming access code 1724. Press the PROGRAM KEY
(3). The display reads:
Use non shelf cooking when you do not need
to reference product to one of the five shelf
positions in the oven. Non shelf cooking may
be used for single stage recipes and MUST be
use for multi-stage recipes.
RECIPE
Press the PROGRAM KEY (3). All of the product
LEDSs will light and the display reads:
Use the PROGRAM ARROW KEYS (4) to select
either YES (for shelf cooking) or NO (for non shelf
cooking). Press the PROGRAM KEY (3).
Select Product
to Program
5. The display reads:
Stage 1 Time
XX:XX
To select the product to program
2. Press the desired product key. The display reads:
Use the PRODUCT KEYS (14) to enter the desired
cook time. Press the PROGRAM KEY (3).
All
Name
6. The display reads:
With All highlighted, press the PROGRAM KEY (3).
The display reads:
Stage 1 Temp
XXXF (or C)
Product Name
AAA
Use the PRODUCT KEYS (14) to enter the desired
cook temperature. Press the PROGRAM KEY (3).
The first alphabetical listing in the product name library appears.
3. To change the product name, use the PROGRAM
ARROW KEYS (4) to scroll through the product name
library. When the desired product name is highlighted,
press the PROGRAM KEY (3) to select.
23
Operation
Blodgett IQ2™ Vision Control
7. The display reads:
Use the PRODUCT KEYS (14) to enter the desired
length of the time the fan should be on in the pulse
cycle. Press PROGRAM KEY (3). The display reads:
Stage 1 Timing
XX:XX
Stage 1 Fan Off
XX:XX
Definition: There are 3 options for timing
mode when shelf cooking: Straight, Flex and
Sensitivity. Straight has no time adjustment.
Flex adjusts the cook time to compensate for
any difference between the setpoint and actual
temperature. Sensitivity enables a product key
to have a flex adjustment for each of the five
shelves. Sensitivity values are set in the manager level programming.
Use the PRODUCT KEYS (14) to enter the desired
length of the time the fan should be off in the pulse
cycle. Press the PROGRAM KEY (3).
10. If you are programming a product using shelf cooking
skip to step 11.
If you are programming a product that does not use
shelf cooking the display reads:
Stage 2 Time
XX:XX
NOTE: Sensitivity is only available when using shelf
cooking.
Use the PROGRAM ARROW KEYS (4) to select the
desired timing mode. Press the PROGRAM KEY (3).
Repeat steps 5 through 10 for each remaining stage.
If you are programming a single stage recipe without
shelf cooking enter at time of 00:00 for stage 2.
8. The display reads:
11. The display reads:
Stage 1 Fan Speed
XX
Alarm 1 Time
XX:XX
Use the PROGRAM ARROW KEYS (4) to select either HIGH or LOW fan speed. Press the PROGRAM
KEY (3).
Definition: If you would like the alarm to sound
prior to the completion of the cook cycle you
may program it here. The alarm time counts
up from the beginning of the cook cycle. For
example, if you want an alarm 9 minutes into
the cook cycle, program the alarm time at 9:00.
9. The display reads:
Stage 1 Fan Cyc
XXX
Use the PRODUCT KEYS (14) to enter the time for
the first alarm to sound. If 00:00 is entered for an
alarm time, skip to step 12.
Definition: There are 3 options for fan cycle
time: Pulse, Heat and Full. Pulse allows the fan
to turn on and off as programmed. Heat allows
the fan to operate with heat only. Full provides
continuous fan operation when door is closed.
Press the PROGRAM KEY (3). If a time other than
00:00 is entered the display reads:
Use the PROGRAM ARROW KEYS (4) to select the
fan cycle. If heat or full are selected skip to step 10. If
pulse is selected the display reads:
Stage 1 Fan On
XX:XX
24
Operation
Blodgett IQ2™ Vision Control
14. The display reads:
Alarm 1 Name
AAA
Hold Done
XXX
To change the alarm name, use the PROGRAM ARROW KEYS (4) to scroll through the alarm name library.
Use the PROGRAM ARROW KEYS (4) to select either AUTOMATIC or MANUAL. Press the PROGRAM
KEY (3).
Press the PROGRAM KEY (3). The display reads:
15. The display reads:
Alarm 1 Done
XXX
Hold Fan Speed
XXX
Use the PROGRAM ARROW KEYS (4) to select either AUTOMATIC or MANUAL.
Use the PROGRAM ARROW KEYS (4) to select
HIGH or LOW. Press the PROGRAM KEY (3).
Press the PROGRAM KEY (3). The display reads:
To exit the program mode
Alarm 1 Tone
XXX
16. The display reads:
Exit
All
Use the PROGRAM ARROW KEYS (4) to select either NONE, SHORT, MEDIUM, LONG, DOUBLE, or
LONG/SHORT.
Press the PROGRAM KEY (3). The display reads:
Use the PROGRAM ARROW KEYS (4) to scroll
down until exit is highlighted. Press the PROGRAM
KEY (3). The display reads:
Alarm 2 Time
AAA
Recipe
Exit
Repeat step 11 for alarm 2. If no Alarm 2 is desired,
enter a time of 0.
12. Press the PROGRAM KEY (3). The display reads:
To program another product key select recipe. To exit
the progam mode select exit. The display reads:
Hold Time
XX:XX
Product Cnt
Programming
Use the PRODUCT KEYS (14) to enter desired hold
time. If a hold time of 00:00 is entered skip to step 13.
Use the PROGRAM ARROW KEYS (4) to scroll down
until exit is highlighed. Press the PROGRAM KEY (3)
to exit the programming mode.
Press the PROGRAM KEY (3).
13. The display reads:
Hold Temp
XXXF
Use the PRODUCT KEYS (14) to enter desired hold
temperature. The minimum hold temperature is 140F.
Press the PROGRAM KEY (3).
25
Operation
Blodgett IQ2™ Vision Control
SYSTEM LEVEL PROGRAMMING
3. The display reads:
Entering the system programming mode
1. Press and hold the PROGRAM KEY (3). The display
reads:
Tone Volume
XXX
Product Cnt
Programming
Use the PROGRAM ARROW KEYS (4) to select
None, 1, 2, 3 or 4. Press the PROGRAM KEY (3) to
select the desired level for all audible signals.
Use the PROGRAM ARROW KEYS (4) to highlight
Programming. Press the PROGRAM KEY (3) to select. The display reads:
4. The display reads:
Temperature
XXX
ENTER CODE
Use the PROGRAM ARROW KEYS (4) to select either F or C. Press the PROGRAM KEY (3) to select
the desired temperature units.
Use the PRODUCT KEYS (14) to enter the programming access code 6647. Press the PROGRAM KEY
(3). The display reads:
5. The display reads:
System
Prod Name Lib
Hold Time
XX:XX
Programming the SYSTEM options
1. With System highlighted, press the PROGRAM KEY
(3) to select. The display reads:
Use the PRODUCT KEYS (14) to enter a hold time.
Press the PROGRAM KEY (3).
6. The display reads:
Appliance Type
XXX
Setback Time
XX:XX
Use the PROGRAM ARROW KEYS (4) to highlight
electric half, electric full, gas half or gas full. Press
the PROGRAM KEY (3) to select the correct appliance type.
Definition: Setback time is an energy savings
feature that automatically lowers the cavity
temperature when the oven is idle.
If the appliance type is changed the display scrolls
“Are you sure, existing recipes will be cleared?” Use
the PROGRAM ARROW KEYS (4) to select either
Use the PRODUCT KEYS (14) to enter a setback
time. Press the PROGRAM KEY (3).
YES or NO.
2. The display reads:
7. The display reads:
Language
XXX
Shelf Sense
XXX
Use the PROGRAM ARROW KEYS (4) to selecteither English or Other. Press the PROGRAM KEY (3)
to select the desired language.
26
Operation
Blodgett IQ2™ Vision Control
This enables you to program a product name. Use
the PROGRAM ARROW KEYS (4) to select either
Yes or No. Press the PROGRAM KEY (3).
Definition: If you are using sensitivity as a timing mode for single stage stage recipes this
feature must be turned on.
12. The display reads:
Use the PROGRAM ARROW KEYS (4) to select either Yes or No. Press the PROGRAM KEY (3).
Recipe Shelf
YES
8. The display reads:
Use the PROGRAM ARROW KEYS (4) to select either Yes or No. Press the PROGRAM KEY (3).
Shelf 1 Sense
XXX
13. The display reads:
Use the PRODUCT KEYS (14) to enter sensitivity
level of 1-9 for shelf 1. Press the PROGRAM KEY
(3). Repeat for shelves 2-5.
Recipe Fan Speed
YES
9. The display reads:
Use the PROGRAM ARROW KEYS (4) to select either Yes or No. Press the PROGRAM KEY (3).
Preheat Time
XXX
14. The display reads:
Recipe Fan Cycle
YES
Definition: This function programs time for the
oven to idle after reaching the preheat temperature allowing heat to saturate the oven cavity.
The preheat time only applies to the initial preheat after a cold start. This is strictly a prompt,
the user may begin a bake cycle even with the
preheat prompt displayed.
Use the PROGRAM ARROW KEYS (4) to select either Yes or No. Press the PROGRAM KEY (3).
15. The display reads:
Recipe Alarm
YES
Use the PRODUCT KEYS (14) to enter a preheat
time. Press the PROGRAM KEY (3).
10. The display reads:
Use the PROGRAM ARROW KEYS (4) to select either Yes or No. Press the PROGRAM KEY (3).
Recipe Stage
YES
16. The display reads:
Recipe Hold
YES
Use the PROGRAM ARROW KEYS (4) to select either Yes or No. Press the PROGRAM KEY (3).
11. The display reads:
Use the PROGRAM ARROW KEYS (4) to select either Yes or No. Press the PROGRAM KEY (3).
Recipe Name
YES
27
Operation
Blodgett IQ2™ Vision Control
17. The display reads:
2. Use the up and down PROGRAM ARROW KEYS (4)
to scroll through the existing product names. Or press
the PRODUCT KEY (14) that corresponds with the
first letter of the name you are looking for. Then use
the PROGRAM ARROW KEYS (4) to scroll to the desired name.
Recipe Timing
YES
Use the PROGRAM ARROW KEYS (4) to select either Yes or No. Press the PROGRAM KEY (3).
3. Press the SCAN KEY (9) to edit the name.
4. Use the PRODUCT KEYS (14) to edit the product
name. Press the right arrow key to advance to the
next character.
18. The display reads
Global Timing
YES
To clear the product name, press the TEMP/TOGGLE/CLEAR KEY (11).
NOTE: Use product key 1 for spaces, periods, quotation marks and underlines.
Definition: There are 3 options for timing
mode when shelf cooking: Straight, Flex and
Sensitivity. Straight has no time adjustment.
Flex adjusts the cook time to compensate for
any difference between the setpoint and actual
temperature. Sensitivity enables a product key
to have a flex adjustment for each of the five
shelves. Sensitivity values are set in the manager level programming.
5. Once the product name has been entered, press the
PROGRAM KEY (3). The display reads:
Save Library
ADD
Use the PROGRAM ARROW KEYS (4) to select either ADD, MODIFY or CANCEL. Select ADD to create a new product name. Select MODIFY to change
an existing product name. Select CANCEL to exit the
edit mode without saving your changes.
Use the PROGRAM ARROW KEYS (4) to select the
timing mode. Press the PROGRAM KEY (3).
Programming the PRODUCT NAME
NOTE: To delete an exsisting product name, find
the name in the product library. Press
the TEMP/TOGGLE/CLEAR KEY (11) to
clear the entire product name. Then select
MODIFY to overwrite the name with a clear
screen.
NOTE: Use these instructions to modify an existing
name, to add a product name or to delete a
name already in the library.
NOTE: Names may be up to 16 characters long and can
contain letters and numbers.
1. After entering the manager level programming (see
page 36) the display reads:
6. Press the PROGRAM KEY (3) to exit the product
name library.
System
Prod Name Lib
With ProdName Lib highlighted, press the PROGRAM KEY (3) to select. The display reads:
Product Name Lib
28
Operation
Blodgett IQ2™ Vision Control
Use the PROGRAM ARROW KEYS (4) to select either ADD, MODIFY or CANCEL. Select ADD to create a new alarm name. Select MODIFY to change an
existing alarm name. Select CANCEL to exit the edit
mode without saving your changes.
Programming the ALARM NAME
NOTE: Use these instructions to modify an existing
name, to add an alarm name or to delete a name
already in the library.
NOTE: Names may be up to 16 characters long and can
contain letters and numbers.
NOTE: To delete an exsisting alarm name, find
the name in the product library. Press the
TEMP/TOGGLE/CLEAR KEY (11) to clear
the entire alarm name. Then select MODIFY
to overwrite the name with a clear screen.
1. After entering the system level programming (see
page 36) the display reads:
6. Press the PROGRAM KEY (3) to exit the alarm name
library.
System
Prod Name Lib
Exiting the system program mode
Use the PROGRAM ARROW KEYS (4) to highlight
Alarm Lib. Press the PROGRAM KEY (3) to select.
The display reads:
1. The display reads:
System
Prod Name Lib
Alarm Name Lib
Use the PROGRAM ARROW KEYS (4) to scroll up
until Exit is highlighted. Press the PROGRAM KEY
(3). The display reads:
2. Use the up and down PROGRAM ARROW KEYS (4)
to scroll through the existing alarm names. Or press
the PRODUCT KEY (14) that corresponds with the
first letter of the name you are looking for. Then use
the PROGRAM ARROW KEYS (4) to scroll to the
desired name.
Product Cnt
Programming
3. Press the SCAN KEY (9) to edit the name.
Use the PROGRAM ARROW KEYS (4) to scroll up
until Exit is highlighted. Press the PROGRAM KEY
(3) to exit the programming mode.
4. Use the PRODUCT KEYS (14) to edit the alarm
name. Press the right arrow key to advance to the
next character.
To clear the alarm name, press the TEMP/TOGGLE/
CLEAR KEY (11).
NOTE: Use product key 1 for spaces, periods, quotation marks and underlines.
5. Once the alarm name has been entered, press the
PROGRAM KEY (3). The display reads:
Save Library
ADD
29
Operation
SmartTouch Touchscreen Control
component description
1. DISPLAY - displays controller related information.
2. USB PORT and COVER - Use to transfer recipes and
data to/from the control
3. CORE PROBE CONNECTION - plug core temperature probe in here when using probe cooking
4. OVEN POWER SWITCH - controls power to the oven.
1
2
3
4
Figure 15
30
Operation
SmartTouch Touchscreen Control
manual mode cooking
1. Select the POWER button to turn on the oven and
proceed to the manual screen.
2. Set the desired cook settings.
A) Temperature - Press the temperature text and
enter the desired oven temperature on the keypad
provided. Press SAVE & EXIT key to return to this
screen.
B) Cook Time - Press the time text and enter the desired cook time on the keypad provided. Press SAVE
& EXIT to return to this screen.
C) Core Probe Cooking - To use the core probe cooking feature, press the PROBE COOK icon. Press the
temperature text that appears and enter the desired
product core temperature on the keypad provided.
Press SAVE & EXIT key to return to the manual cook
screen. Insert a product probe in the probe outlet on
the control panel. To use the HOLD option, press the
HOLD key. Once activated, key will be blue. To escape from probe cooking press the time icon.
D) Fan Speed - Press the fan speed text to toggle
between Low or High.
E) Lights - At any time the lights can be turned on by
pressing the LIGHT icon. The lights will remain on for
15 seconds.
A
C
B
D
E
Figure 16
Figure 17
3. Press START Icon to begin cooking. Press Cancel
key to stop cooking. Press +1 MIN to add 1 minute to
the cook time.
31
Operation
SmartTouch Touchscreen Control
Menu mode cooking
1. On a manual screen, press the ESC key to exit.
4. Select the desired food category for your product.
2. Select the MENU key to cook using the preprogrammed menu items.
Figure 20
5. Within the food category, select the desired product
you wish to cook.
Figure 18
3. Push the SELECT ITEM PRODUCT ICON in the top
right corner of the screen
Figure 21
6. Once selected the control returns to the Menu Cooking screen. Press the START KEY to begin the cook
cycle.
Figure 19
32
Operation
SmartTouch Touchscreen Control
shelf cooking
1. Select the SHELF COOKING key.
3. During the cook cycle, individual shelf cook timers will
count down as the product is cooked. If you wish to
cancel the bake, you can press the PAUSE key, or
you can pause individual shelves.
To add time, select +1 MIN key for individual shelves
or +1 MIN ALL key to add time to all shelves. Each
time the key is pressed, 1 minute of cook time is added.
Press STOP again to reset to the original values.
CLEAR ALL to clear all products from all shelves. All
Shelves must be cleared to escape the screen.
Once the bake is complete the beeper will sound.
Figure 22
2. Select item icon in the upper right corner to select
which item to cook. Select which shelves you intend
to place the selected food item on. Press selected
item icon in the upper right corner of the screen to
add different items that share the same cook temperature but may have different cook times.
Once preheated, start icons will appear. You can
choose start all or start individual shelves.
Figure 24
Figure 23
33
Operation
SmartTouch Touchscreen Control
editing a menu
1. Select the MENU/EDIT icon to edit the recipes in the
menu mode.
3. To edit an existing item, select the item while the EDIT
key at the bottom is highlighted.
To delete an Item, select the item while the DELETE
key is highlighted.
To create a new item, select the NEW ? icon while the
EDIT key is highlighted.
Figure 25
2. Select the EDIT ITEMS icon to edit the menu items.
Figure 27
Figure 26
34
Operation
SmartTouch Touchscreen Control
4. Each recipe is made up of steps containing four settings - temperature, time, fan, etc. A new step is needed when you desire a different setting within a step.
To edit a setting within a particular step, press the
icon for that setting. A keypad will appear for you to
input your value.
To add a step, press the + key icon.
To edit a step, press the arrow keys on the bottom left
hand corner of the screen to highlight the step you
wish to edit. Follow the instructions above to edit the
settings.
To delete a step, use the arrow keys on the bottom
left hand corner of the screen to highlight the step
you wish to delete. Press the red X icon to delete the
highlighted step.
Once you are finished, press the DISK icon to save
the changes.
Figure 28
35
Operation
SmartTouch Touchscreen Control
editing a category
1. Select the MENU/EDIT icon to edit the recipes in the
menu mode.
To delete a category, select the category while the
DELETE key is highlighted.
To create a new category, select the NEW ? icon
while the EDIT key is highlighted.
Figure 29
Figure 31
2. Select the EDIT CATEGORIES icon to select which
items are in each category.
4. Select what you would like to edit.
To edit the name, press the EDIT NAME key. A keyboard will appear, enter the desired name and press
ENTER to return to this menu.
Figure 30
3. To edit an existing category, select the category while
the EDIT key is highlighted.
Figure 32
36
Operation
SmartTouch Touchscreen Control
5. To edit the category icon, press the category icon displayed in the category edit screen. The Select Icon
screen is displayed. Select the desired icon. To view
more icon options, press the arrow key.
6. To edit items within a category, press the SELECT
ITEMS key on the edit category screen.
Select the items you would like to appear within the
category. When complete, press ESC key to return
to the previous menu. Press the DISK icon to save
your changes.
Once the category icon is selected, the category edit
screen is displayed. Press the DISK icon to save your
changes.
Figure 34
Figure 33
37
Operation
SmartTouch Touchscreen Control
creating new menu items
5. Program the recipe steps - Each recipe is made
up of steps containing seven settings - temperature,
time, fan, etc. A new step is needed when you desire
a different setting within a step.
1. Select the EDIT ITEMS key.
To edit a setting within a particular step, press the
icon for that setting. A keypad will appear for you to
input your value.
To add a step, press the + key icon.
To edit a step, press the arrow keys on the bottom left
hand corner of the screen to highlight the step you
wish to edit. Follow the instructions above to edit the
settings.
To delete a step, use the arrow keys on the bottom
left hand corner of the screen to highlight the step
you wish to delete. Press the red X icon to delete the
highlighted step.
Once you are finished, press the DISK icon to save
the changes.
6. To file recipe under an existing category, press the
EDIT CATEGORIES key. Select the desired category. Press the SELECT ITEMS key. Highlight the new
item. Press the ESC key. The disk will be displayed,
press to save your changes.
Figure 35
2. Select New?
3. Select the food icon to be displayed. Use the arrow keys to page through the available icons. Press
the desired icon to select and return to the previous
screen.
4. Name the item. Press the blank shelf below the icon
to name the recipe. A keyboard will appear. Enter the
desired name. Press ENTER when finished to return
to the previous screen.
38
Operation
SmartTouch Touchscreen Control
creating new categories
1. Select the EDIT CATEGORIES key.
4. Press EDIT NAME. A keyboard will appear. Enter the
desired name. Press ENTER when finished to return
to the previous screen.
5. Press SELECT ITEMS. Select items to be filed in the
new category. Items will be highlighted as they are
selected. Press ESC key to return to the previous
screen. The disk will be displayed, press to save your
changes.
6. To display the category, it must be added to the default menu as follows:
Press the EDIT MENUS key. Select the DEFAULT
key. Select the CATEGORIES key. Highlight the new
category. Press the ESC key to return to the previous
screen. The disk will be displayed, press to save your
changes.
Figure 36
2. Select New?
3. Select the category icon to be displayed. Use the arrow keys to page through the available icons. Press
the desired icon to select and return to the previous
screen.
39
Operation
SmartTouch Touchscreen Control
transferring recipes using the usb
To Store Menu Data to a USB
1. Return to the power screen.
1. Press the STORE MENU DATA to USB key to transfer recipes to the USB.
Figure 37
Figure 39
2. Press the TOOLS key. Enter the code 6647 on the
keypad.
2. The keyboard screen is displayed. Use to enter desired file name. Press the ENTER key when finished.
Figure 38
Figure 40
3. Press the MANAGE MENU DATA key. Insert the USB
drive into the Intelliport.
40
Operation
SmartTouch Touchscreen Control
3. The status screen appears to display the download
status. The display returns to the previous screen
when download is complete.
Figure 43
3. The overwrite warning screen appears. Press YES
to continue
Figure 41
4. Press the ESC key to exit USB screen.
To Retrieve Menu Data from USB
1. Press the GET MENU DATA from USB key to transfer
recipes from the USB.
Figure 44
4. The status screen appears to display the upload status. The display returns to the previous screen when
upload is complete.
Figure 42
5. Press the ESC key to exit USB screen.
2. The control displays all menu (.MNU) files on the
USB drive. Select the desired file.
41
Operation
SmartTouch Touchscreen Control
cool down
1. To cool down the unit, press the COOL DOWN icon.
2. The oven will toggle between cooling and open door
in yellow until the oven is cool. Once cool, the oven
will go to standby.
NOTE: If the oven is shut down with the circuit
breaker switch at the bottom of the front
panel, the display will return to the power
screen. Select your option to begin.
Figure 45
Figure 46
42
Operation
How Cook & Hold Works
With the optional COOK & HOLD feature, meat is roasted
at lower temperatures for longer periods of time. This preserves flavor and tenderness and prevents over drying.
There are three phases in cook and hold roasting.
Primary Cooking - controlled by the COOK & HOLD
TIMER. The meat is cooked at a low temperature
until approximately 2/3 done.
•
Cooking from Stored Heat - when the primary cook
time expires, the oven automatically switches to
HOLD. The product continues to cook from the heat
stored in the oven. Meat must remain in the hold
cycle for a minimum of 1-1/2 to 2 hours before being
served.
•
Oven Temp
Product may be
removed and served.
Meat Temp
Hold - holds the product for several hours before
serving without loss of moisture or tenderness.
Time (hours)
All meat should be completely thawed by refrigeration. Using frozen meat increases the cook time causing shrinkage.
Prime rib, bone cap off
14-18 lbs. (6.4-8.1 kg)
Cook
Temp.
200°F
93°C
Prime rib, bone cap on
14-18 lbs. (6.4-8.1 kg)
200°F
93°C
140°F
60°C
Top or bottom rounds
20-22 lbs. (9.1-10.0 kg)
200°F
93°C
140°F
60°C
Pork roast or ham
10-12 lbs. (4.5-5.4 kg)
250°F
121°C
170°F
76°C
Turkey
20-22 lbs. (9.1-10.0 kg)
Leg of Lamb, bone in
8-10 lbs. (4.36-4.5 kg)
250°F
121°C
225°F
107°C
170°F
76°C
160°F
71°C
Product
Stored heat
Product may be
held up to 16 hours
Temperature (°F)
•
Oven switches from cook to hold
Figure 47
Hold Temp.
Quantity
140°F
60°C
1
3
6
1
3
6
1
3
6
2
4
6
1
6
2
4
6
43
Cook Time
(Hrs)
3
3-1/4
3-1/2
3-1/2
4
4-1/2
3-1/2
4
4-1/2
4
4-1/4
4-1/2
3-1/4
4
2-1/2
2-3/4
3
Min. Hold
Time (Hrs)
1
1-1/2
2
1
1-1/2
2
1
1-1/2
2
1
1-1/2
2
1
1-1/2
1
1-1/2
2
Total Time
(Hrs)
4
4-3/4
5-1/2
4-1/2
5-1/2
6-1/2
4-1/2
5-1/2
6-1/2
5
5-3/4
6-1/2
4-3/4
5-1/2
3-1/2
4-1/4
5
Operation
General Guidelines for Operating Personnel
Cook Times and Temperatures
Operating tips
Preheating the oven
Pans and Racks
Always preheat the oven before baking or roasting. We
recommend preheating 50°F (28°C) above the cook temperature to offset the drop in temperature when the doors
are opened and cold product is loaded into the oven. Set
the thermostat to the cook temperature after the product
is loaded.
Product or pan height determines how many racks are
used. The oven holds up to ten 18” x 26” (45.7 x 66.0 cm)
bun pans.
Load the oven from the bottom, centering the pans on the
rack. Never place a pan or aluminum foil on the bottom
of the oven. This obstructs the flow of air and results in
uneven baking and roasting.
NOTE: For frozen product, preheat the oven 100°F
(56°C) above the cook temperature.
Roasting
Cook Temperatures
To reduce shrinkage when roasting, place meat directly on
the racks. Place a sheet pan one-half full of water in the
bottom rack position. The water evaporates, increasing
humidity in the oven chamber. The pan catches grease
from the meat, making oven cleaning easier.
Generally, cook temperatures should be 50°F (28°C) lower than deck or range oven recipes. If the edges of the
product are done but the center is raw, or if there is color
variation, reduce the thermostat setting another 15-25°F
(10-15°C). Continue to reduce the cook temperature on
successive loads until the desired results are achieved.
Baking
Weigh the product to ensure equal distribution in each
pan. Varying amounts of product will cause uneven baking results.
NOTE: Cooking at excessive temperatures will not
reduce cook time, it will produce unsatisfactory
baking and roasting results.
Fans
Cook Time
The fan must be operating for the oven to heat. Use the
Pulse Plus feature to allow light or liquid product to set
in the pan and to avoid rippling towards the fan. If your
oven is not equipped with this feature use the following
procedure.
Check the product in about half the time recommended
for deck or range oven recipes. Record times and temperatures which provide best results for future reference.
NOTE: Cook time will vary with the amount of product
loaded, the type of pan and the temperature.
1. Preheat the oven 25°F (15°C) above the baking temperature.
2. Load the oven with product. Close the doors.
3. Set the thermostat to the baking temperature.
4. Turn the oven off.
5. Allow the product to set for 5-7 minutes with the fan
off. The residual heat in the oven sets the product.
6. Turn the oven on for the remainder of the bake.
Lights
Turn the oven lights off when not viewing the product.
Leaving the lights on for extended periods of time shortens the bulb life considerably.
44
Operation
Suggested Times and Temperatures
product
temperature
time
# shelves
Hamburger Patties (5 per lb)
400°F (205°C)
8-10 mins.
10
Steamship Round (80 lb. quartered)
275°F (135°C)
2 hrs 45 mins.
2
Standing Rib Choice (20 lbs, trimmed, rare)
235°F (115°C)
2 hrs 45 mins.
2
Banquet Shell Steaks (10 oz. meat)
450°F (235°C)
7-8 mins.
5
Swiss Steak after Braising
275°F (135°C)
1 hr.
5
Baked Stuffed Pork Chop
375°F (190°C)
25-30 mins.
5
Boned Veal Roast (15 lbs.)
300°F (150°C)
3 hrs. 10 mins.
2
Lamb Chops (small loin)
400°F (205°C)
7-8 mins.
5
Bacon (on racks in 18” x 26” pans)
Poultry
400°F (205°C)
5-7 mins.
10
Chicken Breast & Thigh
350°F (175°C)
40 mins.
5
Chicken Back & Wing
350°F (175°C)
35 mins.
5
Chicken (21/2 lbs. quartered)
350°F (175°C)
30 mins.
5
Turkey Rolled (18 lb. rolls)
Fish and Seafood
310°F (155°C)
3 hrs 45 mins.
3
Halibut Steaks, Cod Fish (frozen 5 oz)
350°F (175°C)
20 mins.
5
Baked Stuffed Lobster (21/2 lb.)
400°F (205°C)
10 mins.
3
Lobster Tails (frozen)
Cheese
425°F (220°C)
9 mins.
5
Macaroni & Cheese Casserole
350°F (175°C)
30 mins.
5
Melted Cheese Sandwiches
Potatoes
400°F (205°C)
8 mins.
10
Idaho Potatoes (120 ct.)
400°F (205°C)
50 mins.
5
Oven Roasted Potatoes (sliced or diced)
Baked Goods
325°F (165°C)
10 mins.
5
Frozen Berry Pies (22 oz)
325°F (150°C)
35 mins.
5 (30 pies)
Fresh Apple Pie (20 oz.)
350°F (175°C)
25-30 mins.
5 (30 pies)
Pumpkin Pies (32 oz.)
300°F (150°C)
30-50 mins.
5 (20 pies)
Fruit Crisp
300°F (150°C)
25 mins.
5
Bread (24 - 1 lb. loaves)
325°F (155°C)
30 mins.
3
Southern Corn Bread
375°F (190°C)
15-20 mins.
5
Baking Soda Biscuits
400°F (205°C)
6 mins.
5
Brown & Serve Rolls
350°F (175°C)
15 mins.
5
Sheet Cakes (5 lb. mixed batter per pan)
325°F (160°C)
16-18 mins.
5
Chocolate Cake
325°F (160°C)
20 mins.
5
Meats
Brownies
325°F (150°C)
15 mins.
5
NOTE: Actual times and temperatures may vary considerably from those shown above. They are affected by weight of
load, temperature of the product, recipe, type of pan and calibration of thermostat. Should your recipe vary, write
in your proven time and temperature for ready reference.
45
Maintenance
Cleaning and Preventative Maintenance
daily cleaning
Clean cooling fan
Oven Cool Down:
1. Brush off the cooling fan located on the back of the
oven behind the control compartment.
1. Turn the oven to COOL DOWN.
NOTE: The doors may be opened to speed the
cooling process.
preventative maintenance
Annual Maintenance
Cleaning the exterior
The following checks should be part of an annual scheduled maintenance. This maintenance must be performed
by an authorized service agency. Contact your local
Blodgett service company, a factory representative or the
Blodgett Oven company.
1. Saturate a cloth with a mild soap and water mixture.
Wipe the oven when it is cold.
2. Dry the oven with a clean cloth.
3. Heat tint and heavy discoloration may be removed
with any non-toxic, non-caustic, commercial oven
cleaner and stainless steel polish.
1. Check venting system.
2. Check temperature calibration.
Cleaning the interior
3. Adjust and grease door switch for proper closure.
Deposits of baked on splatter may be removed with any
non-toxic, non-caustic, food safe, commercial oven cleaner.
4. Clean any debris out of control tray. Check for loose
connections. Replace any discolored connections.
5. Retorque all electrical connections between the element and contactors.
1. Apply cleaner following the manufacturer’s direction.
Always rub with the grain of the metal.
WARNING!!
weekly cleaning
Always disconnect the appliance from the
power supply before servicing or cleaning.
1. Remove any loose debris or particle buildup from the
racks, rack supports, baffle, blower wheel and temperature probe.
monthly cleaning
Clean racks, rack supports, baffle and blower wheel
1. Remove the racks, rack supports and baffle.
2. Hold the blower wheel with a gloved hand.
3. Use an L-shaped brush to clean the fins on the blower wheel.
4. Use a hand brush to clean the center portion of the
blower wheel.
5. Wipe around the fan with a damp towel.
6. Soak racks, supports and baffle in a solution of nontoxic, non-caustic, food safe, commercial oven cleaner. Allow to soak overnight if necessary.
7. Reinstall parts.
Clean temperature probe
1. Use a damp towel to wipe the probe. Handle with
care.
46
Maintenance
Troubleshooting Guide
POSSIBLE CAUSE(S)
SYMPTOM: Heating elements do not come on.
• Oven not plugged in.
•
Plug in electrical supply cord.
•
Power switch on the control panel is off.
•
Set the control panel to COOK or OVEN ON.
•
Control set below ambient temperature.
•
Set to desired cook temperature.
•
Doors are open.
•
Close doors.
•
Computerized controls - error code on display.
•
*
SYMPTOM: Oven does not come to ready.
• The oven has not reached preheat temperature.
•
Wait for oven to reach preheat temperature.
•
Fan delay feature may be activated, if applicable.
•
Deactivate fan delay feature.
•
Internal problem with main temperature control.
•
*
SYMPTOM: Convection fan does not run.
• Oven is not plugged in.
•
Plug in electrical supply cord.
•
Oven is not set to the cook mode.
•
Set the control panel to COOK or OVEN ON.
•
Circuit breaker tripped.
•
Reset the breaker.
•
Fan delay feature may be activated, if applicable.
•
Deactivate fan delay feature.
•
Doors are open
•
Close doors.
•
Reprogram control per Operation section.
SYMPTOM: General baking problems.
• Computerized controls - incorrect product programming.
SUGGESTED REMEDY
• Thermostat out of calibration.
• *
*Denotes remedy is a difficult operation and should be performed by qualified personnel only. It is recommended, however, that All repairs and/or adjustments be done by your local Blodgett service agency and not by the owner/operator.
Blodgett cannot assume responsibility for damage as a result of servicing done by unqualified personnel.
WARNING!!
Always disconnect the power supply before cleaning or servicing the oven.
47