Cleveland ConvectionPro Steamers 36CGM16 Owner`s manual

Heated Cabinet/Proofer
• Piper’s aluminum heated cabinets/proofers are designed with
features to make your operation efficient
• Controls can be easily accessed at the front of the cabinet without
opening the doors
• Entire heater unit can be removed for cleaning and maintenance
• Holds (34) 18” x 26” pans
• One year parts and labor warranty
• 213⁄8” w. x 31” d. x 681⁄8” h., channels spaced on 11⁄2” centers with
5
⁄8” ledge
• 120V, 1500 watts
934-H
Equipment
Proofer Cabinet, Oven, Blast Chiller/Shock Freezer
Cook & Hold Oven
• The Chef System Cook & Hold Oven roasts meat, poultry and fish,
to juicy tenderness...and holds the flavor until ready to serve.
• Exclusive Roast-Air™ process, Chef System uses radiant and
convection heat that browns naturally, tenderizes and holds
natural juices, creating distinctive and tasteful entrees
• Holds 5 pans
• 261⁄4” w. x 347⁄8” d. x 34” h. w/standard casters
• Cabinet opening: 181⁄4” w. x 201⁄2” h.
• One year parts and labor warranty
• 120/60/1 or 208/240/60/1
CS2-5
Blast Chiller/Shock Freezer
•
•
•
•
•
•
•
•
•
•
•
•
Monoblock construction
Stainless steel top, sides, doors
Stainless steel feet - 2” with adjustable height
Electronic control board with display, showing the status of the
appliance in every moment
Microprocessor is able to memorize till 100 programs
Self-closing doors
Polyurethane insulation, HCFC-free
Anti-condensation heating element in the body
Full length ergonomic handle
R404A refrigerant
31.10˝ w. x 27.56˝ d. x 33.46˝ h.
208-240V, 1 Ph., 60 Hz.
RCM051S
222_241NAFEDcat.indd 229
229
9/26/07 4:23:44 PM
Equipment
Impinger Ovens
Fusion™ Conveyor Toasters
Dome-shaped reflector bounces heat in a focused manner, and watt distribution along the heater’s length
allows concentration of heat where it is most needed. Fully adjustable for faster toasted foods thanks to better
convection and focused heat.
• Stainless steel finish standard, optional colors available
• Self-contained and conveyorized
• Designed for countertop use and must be used with the appropriate 4˝ legs for proper cooling
• Energy saving “sleep” mode
• Cool-Skin exterior stays cool to the touch during operation
• Air curtain prevents heat loss
• Convenient controls include four programmable buttons/pre-sets
with a “manual” cook setting mode, conveyor direction control
and sleep mode switch
• Intensity is adjustable from 0.0 to 10.0
• Flexible stainless steel conveyor belt has the capacity
for 14˝ wide product and a travel distance of 401⁄4˝,
of which 21˝ is in the chamber
• Conveyor speed is adjustable from 15 seconds to
5 minutes cooking time
• Removable crumb trays for ease of cleaning
2040
2041
208/240V, 1 Phase
208/240V, 3 Phase
Impinger® Ovens
The Lincoln® Impinger® oven will bake, cook, reheat and finish virtually any food item up to two to four times faster than other conventional
ovens - at lower temperatures, in less space and at less cost. Even a small oven can greatly increase hourly output over a deck oven. This
means faster service for your customers and greater profits for you.
Countertop Impinger® Ovens
• This impinger puts large oven capacity almost
anywhere you need it
• The Impinger Countertop cooks just like the larger
Impinger models and can be stacked two high
• In most applications it requires no venting
• Bakes 144 chocolate chip cookies or
14 large pizzas per hour
• Capacity equal to a half size convection
oven or up to five microwave ovens
• 16˝ conveyor capacity
• 493⁄4˝ l. x 313⁄8˝ d. x 18˝ h.
SHOWN WITH OPTIONAL
1301/1353
208V
EXTENDED 50˝ CONVEYOR
1302/1353
240V
Impinger® II Express Ovens
• Front loading, removable conveyor
• Designed for applications where demand is
high and floor space is limited
• The 18˝ conveyor can move as much
as one or two deck ovens
• Can be stacked 3 high, maximizing
capacity and flexibility
• 56˝ l. x 46.12˝ d. x 42˝ h.
1116-000-U
1117-000-U
1130-000-U
Natural Gas 40,000 BTU, 120V
LP Gas 40,000 BTU, 120V
Electric 10kW, 120/208V
SHOWN WITH
OPTIONAL MOBILE
STANDS
230
222_241NAFEDcat.indd 230
230
9/26/07 4:23:48 PM
BCX Series Combi Oven
THE NEW BCX SERIES COMBI OVEN FROM BLODGETT - LET OUR DURABILITY PROFIT FOR YOU!
The future of Combi cooking has arrived with the introduction of the NEW BCX-14 Series Combi Ovens. Built with solid, reliable Blodgett
construction, the BCX-14 is designed to last for years of rigorous use in the American kitchen. The BCX-14 provides all the features you need
to increase production while decreasing your time, labor and maintenance costs.
• User friendly controls - cutting edge technology yet simple to operate
• EXCLUSIVE Steam On Demand which allows you to inject steam at the touch of a button
• Four speed, bi-directional fan to eliminate hot spots and a vent switch to vent the oven
cavity at any time
• EXCLUSIVE Time to Delime indicator with semi-automatic deliming
• Four bright halogen lights for superior product visibility
• Detachable core temperature probe for precise probe placement and easy cleaning
• Two step door latch keeps the operator safe from escaping steam. Just turn the handle to
left to vent the steam, then to the right to fully open the door
• Dual pane thermal glass window swings open for cleaning between the panes
• No spill, door mounted drip pan keeps your floors dry
• Integrated wash down hose
• Thirteen (13) position rack guides
• Five (5) stainless steel wire shelves
• Pan capacity: (7) full size 18” x 26” bake pans
or (14) 12” x 20” x 2-1/2” steam table pans
BCX-14E Electric, Single Unit
BCX-14G Gas, Single Unit
Equipment
Convection Ovens
BCX-14G SHOWN
WITH OPTIONAL
STAND AND CASTERS
BCX-14E SHOWN
WITH OPTIONAL
STAND AND CASTERS
DFG-100 Full Size Dual Flow Gas Convection Oven
THE DFG-100 OVEN OFFERS ALL OF BLODGETT’S SIGNATURE FEATURES
• Welded angle iron frame, modular slide out front control panel, double-sided porcelain cavity, triple
mounted dependent doors, rigid frame "Blodgett Block" insulation to eliminate hot or cold spots
• Full two-year parts, one year labor warranty, five year limited warranty on door for U.S. & Canada
PLUS YOU GET THE ADVANTAGES OF THESE STANDARD FEATURES
• Stainless steel front, top, and sides
• Standard depth baking compartment - accepts five 18” x 26” standard full size
baking pans in left-to-right positions
• Dual pane thermal glass windows encased in stainless steel door frames
• Solid state thermostat with temperature control range of 200-500˚F.
• Dual Flow Gas system combines direct and indirect heat
• Solid state manual control (other control options available), with separate dials
to control thermostat and timer
• Two-speed, 1⁄3 hp. convection motor w/ automatic thermal overload protection
• Two speed fan motor (60 Hz only, not available in 50 Hz)
• Triple-mounted pressure lock door design with turnbuckle assembly
• Porcelain door handle with simultaneous door operation
• Solid mineral fiber insulation at top, back, sides and bottom
• Double-sided porcelainized baking compartment liner (14 gauge)
• Aluminized steel combustion chamber
• Dual inlet blower wheel
• Five chrome-plated racks, eleven rack positions with a minimum of 15⁄8˝ spacing
• Interior lights, two 50 watt commercial bake oven lamps
• Electronic spark ignition control system
• Removable dual tube burners
• Pressure regulator
• Manual gas service cut-off switch located on the front of the control panel
• Air mixers with adjustable air shutters
DFG-100
• Control area cooling fan
SHOWN WITH
• Adjustable stainless steel legs
OPTIONAL CASTERS
• Blodgett ovens stand the test off time, have a low cost of ownership,
and are easy to clean and service
DFG-100
222_241NAFEDcat.indd 231
231
9/26/07 4:23:51 PM
Equipment
Steamers, Ranges & Skillets
Eco-Tech™ Steamers
Most hassle-free steamer you’ll ever install!
• Simply hook up to your power
• No need for a water filter, water connection or drain
• Fill the Eco-Tech™ with 21⁄2 gallons of water, and minutes
later you’re ready to cook
• Early warning light lets you know when to add water, while
an audible alert sounds before the generator is empty
• Choose from 3 or 6 pan models
• Comes standard with a removable drip trough and drain pan, power saver
mode switch, steam & hold capability and 4˝ adjustable feet
• Both models available in the following electrical configurations: 208, 220,
240 and 480 volts; 1 and 3 phase
SUPERIOR PERFORMANCE: The Eco-tech™ provides faster and better cooking
performance than competitive models. It virtually eliminates flavor transfer
because of its unique design. It even has a constant steam mode and idle
mode for quick recovery.
EASY TO MAINTAIN: Designed for reliability, with easy maintenance and
serviceability built in. Does not require daily deliming.
ET-3E
ET-6E
Holds 3 pans
Holds 6 pans
6 kW input
9 kW input
24˝ w. x 30˝ d. x 211⁄2˝ h.
24˝ w. x 30˝ d. x 28˝ h.
ET-6E
SHOWN ON OPTIONAL
STAND WITH CASTERS
Gas Range
UniVerse Plus Tilting Skillets™
• 6 burner range • Stainless steel front, ledge, sides, backguard & shelf
• Chrome plated rack with support rack guides allowing
up to four rack positions
• Exclusive double-venting beneath stainless steel high
back shelf to reduce heat build-up
• “No Burn-Zone” to reduce burn stains on stainless steel back
• 35,000 BTU lift-off burner heads (40,000 BTU on request) with builtin pilot shield for high performance cooking and easy cleaning
• 12˝ x 12˝ heavy duty cast iron section grates remove easily & safely
• Cast-in bowl directs heat to the cooking surface
• Grate design allows pots to slide from section to section
• 6˝ wide stainless landing ledge provides a functional working area
• 30˝ w. oven is porcelainized on 5 contact surfaces for easy cleaning
• 36˝ w. x 295⁄8˝ d. x 565⁄8˝ h.
Add convenience and versatility to your kitchen by enabling
you to cook several different ways from one compact unit!
• Ideal for soups, pancakes, stir-fry and more
• Add a new level of efficiency to any medium-to-large
scale foodservice operation
• Available in gas or electric inputs in 30 or 40 gallon sizes
• All come in marked 5-gallon increments
• Heavy-duty hinged assist cover with condensate vent is also included
• Motorized or manual tilt mechanism, easy-pour lip design, removable
grease strainer and 60-minute timer
MF-R6
SHOWN WITH
OPTIONAL
CASTERS
232
222_241NAFEDcat.indd 232
232
9/26/07 4:23:54 PM
Bronze Convection Oven
•
•
•
•
•
•
•
•
•
SHOWN WITH
OPTIONAL CASTERS
Single – 55" standard height
54,000 BTU
Uni-body construction
"Plug and Play" controls
Fully front serviceable
Double sealed dependent doors
Patented Jet Stream burner system
Hot surface ignition system
24/7 Warranty
COMBINING COOKING TECHNOLOGIES, WHEN APPLIED APPROPRIATELY, WILL
RESULT IN HIGH QUALITY FOOD PRODUCTS, REDUCED COOK TIMES AND REDUCED
STEPS IN PREPARATION. CONVECTION AND MICROWAVE COOKING HAVE BOTH
PROVEN THEMSELVES AS STAND ALONE TECHNOLOGIES. HOWEVER, WHEN BOTH
ARE USED SIMULTANEOUSLY, THE OPERATOR PRODUCES FOOD IN A REDUCED TIME
FRAME THAT HAS A BETTER APPEARANCE.
Equipment
Convection Ovens
SilverStar Convection Oven
•
•
•
•
•
•
•
•
•
•
•
•
Single – 55" standard height/Double – 64" standard height
72,000 BTU
Stainless steel front, top, sides
Uni-body construction
"Plug and Play" controls
Interior light
Fully welded door frames
Fully front serviceable
SHOWN WITH
Double sealed dependent doors
OPTIONAL CASTERS
Patented Jet Stream burner system
Hot surface ignition system
24/7 Warranty
Marathoner Gold Convection Oven
•
•
•
•
•
•
•
•
•
•
•
•
•
Single – 55" standard height/Double – 64" standard height
90,000 BTU
Stainless steel front, top, sides
Stainless steel rear jacket
Uni-body construction
"Plug and Play" controls
Fully welded door frames
Fully front serviceable
Double sealed dependent doors
Patented Jet Stream burner system
Hot surface ignition system
Interior lights
24/7 Warranty
SHOWN WITH
OPTIONAL CASTERS
233
222_241NAFEDcat.indd 233
9/26/07 4:23:58 PM
Equipment
Combi-Oven Steamers
Convotherm by Cleveland
Combi Oven-Steamers
FEATURING THE “ADVANCED CLOSED SYSTEM +3”
COOKING MODES:
• Hot Air • Retherm • “Delta T” slow cooking
• Steam • “Cook & Hold” • “Crisp & Tasty” • Combi
PRODUCT FEATURES:
• Efficient heating system provides fast heat up times
• Advanced closed system with “Crisp & Tasty” de-moisturizing feature
• Polished cooking compartment with coved corners for easy cleaning
• Hinged fan guard and hinged removable pan racks
• Space saving, easy to close “Disappearing Door”
• Door latch with safety vent position and wear-free door switch
• Vented, double glass door with integrated door stop
• Easy to change, press-fit door seal
• Oven light with shock resistant safety glass
• Multipoint core temperature probe
• Easy to use electronic controls for all operational functions
• Self diagnostic system with full text message display
• Easy to understand menu icons with bright graphics display
• User friendly selector dial
• Exclusive “Smart Key” for selecting option settings
• Digital controls for temperature, time and core probe settings
• Eight (8) “Press & Go” one step, recipe start buttons
• Cook book library for up to 250 stored recipe
programs, each recipe capable of 20 steps
• Smooth action hand shower for compartment cleaning
OEB-10.10
• Capacity: Ten (10) - 12” x 20” x 21⁄2” pans
• Includes three (3) 26” x 20” wire shelves
OES-10.10
OEB-10.10
OGS-10.10
OGB-10.10
Electric, Boilerless
Electric, With Steam Generator
Gas, Boilerless
Gas, With Steam Generator
GAS AND ELECTRIC BOILERLESS MODELS
• Fully insulated cooking compartment for maximum energy savings
• Injection system for steam
• Auto reversing convection fan for even heat distribution
GAS AND ELECTRIC STEAM GENERATOR MODELS
• Fully insulated steam generator and cooking
compartment for maximum energy savings
• Two (2) speed auto reversing convection fan for even heat distribution
• Built-in automatic rinse system
• Automatic fill and water level control
• Automatic generator drain
OEB-20.20
OES-6.20
• Capacity: Seven (7) - 18” x 26” full size sheet pans
Fourteen (14) - 12” x 20” x 21⁄2” pans
• Includes three (3) 26” x 20” wire shelves
OES-6.20
OEB-6.20
OGS-6.20
OGB-6.20
234
222_241NAFEDcat.indd 234
Electric, Boilerless
Electric, With Steam Generator
Gas, Boilerless
Gas, With Steam Generator
• Capacity: Twenty (20) - 18” x 26” full size sheet pans
Forty (40) - 12” x 20” x 21⁄2” pans
• Includes six (6) 26” x 20” wire shelves
OES-20.20
OEB-20.20
OGS-20.20
OGB-20.20
Electric, Boilerless
Electric, With Steam Generator
Gas, Boilerless
Gas, With Steam Generator
234
9/26/07 4:24:01 PM
SteamChef™ Electric Counter Type Convection Steamers
• Easy-to-clean open “boilerless style” electric steam generator
• Fan forced convection steam with KleanShield™ cooking compartment design – eliminates
foaming and avoids contamination of the reservoir water • Automatic water fill
• High temperature safety shut-off
• Comes standard with SureCook compartment controls, 60 minute electro-mechanical
timer with load compensating feature, LED indicator lights for SureCook cycle, power on
and reset • Timed and manual bypass switch for constant steaming
• Exclusive SteamChef™ automatic drain control
• Heavy-duty 4˝ skid resistant stainless steel adjustable
legs with flanged feet
22CET3.1
22CET6.1
Holds up to (3) 21⁄2” d. Full-size Steam Table Pans, 9 kW
Holds up to (6) 21⁄2” d. Full-size Steam Table Pans, 13.5 kW
OPTIONAL STAINLESS STEEL EQUIPMENT STANDS
ES222834
34” high, Economy Stand, Holds One 22CET3A
ES222834PR 34” high, Deluxe Stand with Bottom Shelf and One Set of Pan Racks, Holds One 22CET6
STACKING STANDS AVAILABLE FOR MOUNTING TWO STEAMCHEF™ STEAMERS
22CET3.1
Equipment
Convection Steamers
SteamCraft® Ultra Convection Steamers
THE MOST ADVANCED COUNTER TYPE CONVECTION STEAMER IN THE INDUSTRY!
• Ideal for restaurants and cafeterias or hospitals
• Heavy duty stainless steel construction • Electric or gas steam generator
• Gas model includes 4” stainless steel adjustable legs
• Easy access generator cleaning port
• Standard with 60 minute electro-mechanical timer and switch for manual operation
• Main power on/off switch • Automatic generator drain
• Unique patented steam cooking distribution system
• Patented automatic remote probe type water level control
• Exclusive “Cool to the Touch” two-piece compartment door design
ELECTRIC
21CET8
Holds up to (3) 21⁄2” d. Full-size Steam Table Pans, 8.5 kW
21CET16 Holds up to (5) 21⁄2” d. Full-size Steam Table Pans, 16.5 kW
GAS
21CGA5 Holds up to (5) 21⁄2˝ d. or (10) 1˝ d. Full-size Steam Table Pans, 75,000 BTU
21CET16
SHOWN WITH
OPTIONAL ELECTRONIC
TIMER
OPTIONAL STAINLESS STEEL EQUIPMENT STANDS
ES21301 34” high, with Bottom Shelf and One Set of Pan Racks, Holds One 21CET8 or 21CET16 or 21CGA5 Steamer
ES2130S Holds Two 21CET8 Steamers
ES2446
Includes Bottom Shelf and One Set of Pan Racks, Holds Two 21CET8 or One 21CET8 and One 21CET16, or Two 21CET16 Steamers
Steamcraft® Gas Steamers
•
•
•
•
•
•
•
Durable 14 gauge stainless steel construction for compartment door, cavity and steam generator
Two 60 minute timers and switches for manual operation
Main power On/Off switch • Automatic drain • Condensate drip trough
Unique patented steam cooking distribution system
Exclusive “Cool to the Touch” two-piece compartment door design
Total Capacity: (10) 21⁄2” d. full-size steam table pans
NSF certified 6” stainless steel legs
24CGA10
STEAMCRAFT® ULTRA 10
• Pressureless vertical atmospheric steam generator
• 125,000 BTU input
24CGP10
STEAMCRAFT® POWER 10
• High efficiency forced air gas-fired boiler – produces 180 lb. of steam per hour
• 10-12 PSI operating generator pressure
• 240,000 BTU input
OPTIONAL ELECTRONIC TIMER WITH LOAD COMPENSATING FEATURE IS AVAILABLE.
24CGA10
SHOWN WITH
OPTIONAL ELECTRONIC
TIMER
235
222_241NAFEDcat.indd 235
9/26/07 4:24:06 PM
Equipment
Convection Steamers
Cleveland Classic Series Convection Steamers
•
•
•
•
•
•
•
•
•
•
•
•
•
24” wide modular cabinet base with hinged door
NSF Certified 6” stainless steel legs
Pressureless cooking with forced convection steam permits doors to be opened while cooking continues
Solid state controls operate water level and safety functions
Each compartment is equipped with a 60 minute mechanical timer, separate bypass switch
for constant steaming and a cold water condenser for superior cooking results
Instant steam standby mode holds generator at steaming temperature
Steam generator automatic water fill on start up and automatic generator drain at shutdown
Separate main power switch for “On/Off”
Durable 14 gauge stainless steel cooking compartment door and steam cooking cavity
Cold water condenser for each compartment maintains a dry steam
Exclusive “cool to the touch” compartment door design with stainless steel slam/latch door latch mechanism
Left hand door hinging: compartment doors hinged left, controls on the right
Each compartment holds up to (3) 21⁄2” d. full-size steam table pans
24-CGM-200
200,000 BTU Gas Fired Steam Generator with Nickelguard™
24-CEM-24
24 kW Electric Steam Generator
OPTIONAL ELECTRONIC TIMER WITH LOAD COMPENSATING FEATURE IS AVAILABLE
24-CEM-24
ConvectionPro XVI® Convection Steamers
•
•
•
•
•
•
•
•
•
•
36” wide modular cabinet base with hinged door
Heavy duty stainless steel base frame
NSF Certified 6” stainless steel legs
Pressureless cooking with forced convection steam permits
doors to be opened while cooking continues
Solid state controls operate water level and safety functions
Each compartment is equipped with a 60 minute mechanical timer, separate bypass
switch for constant steaming and a cold water condenser for superior cooking results
Audible and visual signals for cycle completion and steam shut-off
Durable 10 gauge stainless steel cooking compartment door and steam cooking cavity
Insulated cooking compartments
Each compartment holds up to (8) 21⁄2” d. full-size steam table pans or (4) 12” x 18” bun pans
36-CGM-16-300
300,000 BTU Gas Fired Steam Generator with Nickelguard™
36-CEM-16-48
48 kW Electric Steam Generator
OPTIONAL ELECTRONIC TIMER WITH LOAD
COMPENSATING FEATURE IS AVAILABLE
36-CGM-16-300
SHOWN WITH OPTIONAL ELECTRONIC TIMER
SteamCraft® Gemini™ Pressureless Steamers
• Twin, independent steam generators – each steam-cooking compartment is independently operated and
controlled by a separate stainless steel steam generator
• Gas-fired models have high efficiency independent power burner steam generators
• Electric model has two 8 kW fire bar heating elements per compartment
• Doors hinged left and the controls on the right
• Easy access cleaning port
• Generator cleaning light
• Generator steam standby mode
• Each compartment has one, 60-minute electro-mechanical timer with “Sure-Cook” load compensating
feature. Manual bypass switch for constant steaming
• 14 gauge stainless steel construction for compartment door, cooking cavity and steam generator
• Exclusive Gemini drain/power control system: 1⁄2” “ball valve” type drain that controls main power on/off
and automatically fills generator (located on the control panel)
• Brass steam jets distribute steam evenly
• 6” stainless steel adjustable legs with flanged feet
• Compartment steam shut-off switch when door is opened
236
GAS
24CGA6.2
Each compartment holds (3) 21⁄2˝ d. full-size pans, 50,000 BTU’s per compartment
24CGA10.2
Each compartment holds (5) 21⁄2˝ d. full-size pans, 72,000 BTU’s per compartment
ELECTRIC
24CEA10
Each compartment holds (5) 21⁄2˝ d. full-size pans, 16 kW per compartment
OPTIONAL ELECTRONIC TIMER WITH LOAD COMPENSATING FEATURE IS AVAILABLE
24CGA10.2
222_241NAFEDcat.indd 236
236
9/26/07 4:24:09 PM
Gas-Fired Stationary Steam Jacketed Kettles
•
•
•
•
2/3 steam jacketed
Steam jacket permanently filled with treated distilled water
Support legs with level adjustable feet, flanged for floor bolting
Precise, consistent temperature control with less than 1°C. temperature variance
– ideal for simmering
• Operating temperature range from 145°F. - 260°F. (63°C. - 127°C.)
• “Splash-Proof” solid-state control panel
• Type 304 stainless steel with #4 finish on kettle and supports
• 50 psi steam jacket rating and safety valve
• Spring-assisted cover and 2” tangent draw-off are standard
• Automatic ignition system
• Standard for natural gas operation
• Supplied with cord and plug for 115V operation
ALSO AVAILABLE SHORT SERIES™ WITH LOWER RIM
KGL-25
25 gallon capacity
HEIGHTS. ALSO AVAILABLE TILTING.
KGL-30
30 gallon capacity
KGL-40
40 gallon capacity
KGL-60
60 gallon capacity
KGL-80
80 gallon capacity
KGL-100
100 gallon capacity
Equipment
Kettles
KGL-40
Electric Stationary
Steam Jacketed Kettles
•
•
•
•
2/3 steam jacketed
Steam jacket permanently filled with treated distilled water
Support legs with level adjustable feet, flanged for floor bolting
Precise, consistent temperature control with less than 1°C.
temperature variance – ideal for simmering
• Operating temperature range from 145°F. - 260°F.
(63°C. - 127°C.)
• “Splash-Proof” solid-state control panel
• Type 304 stainless steel with #4 finish on kettle and supports
• 50 psi steam jacket rating and safety valve
• Spring-assisted cover and 2” tangent draw-off are standard
• Welded-in heating elements
• Standard voltage 208-240V, 60 Hz., 3-phase, 3-wire
ALSO AVAILABLE SHORT SERIES™ WITH LOWER RIM HEIGHTS.
ALSO AVAILABLE TILTING.
KEL-40
KEL-25
KEL-30
KEL-40
KEL-60
KEL-80
KEL-100
KEL-40-SH
SHORT SERIES™
SHOWN WITH OPTIONAL HOT &
COLD WATER FAUCET
25 gallon capacity
30 gallon capacity
40 gallon capacity
60 gallon capacity
80 gallon capacity
100 gallon capacity
Steam Jacketed Kettles
• Precise, consistent temperature control with less than 1° F. variance
• Steam jacket permanently filled with treated distilled water
• Solid state controls
• Kettle and all exterior surfaces type 304 stainless steel
• Easy manual tilting
• Large pouring lip for chunky products
AVAILABLE WITH OPTIONAL LIFT-OFF COVER
TABLE TOP MODELS
GAS
KGT-12-T 12 gallon, 24” w. x 183⁄4” d. x 283⁄4” h.
ELECTRIC
KET-3-T
3 gallon, 201⁄4” w. x 131⁄4” d. x 287⁄8” h.
KET-6-T
6 gallon, 24” w. x 17” d. x 281⁄2” h.
KET-12-T
12 gallon, 271⁄2” w. x 20” d. x 34” h.
FLOOR MODEL
• Includes 6” level adjustable feet
ELECTRIC
KET-20-T
20 gallon, 32” w. x 271⁄2” d. x 493⁄4” h.
222_241NAFEDcat.indd 237
KET-20-T
KET-12-T
237
9/26/07 4:24:12 PM
Equipment
Skillets
DuraPan™ Series Tilting Skillets
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Available with modular or open base design
Power tilt
Stainless steel clad 5⁄8˝ cooking surface
Stainless steel coved cornered pan
Space-saving design
All stainless steel construction for durability and easy cleaning
Adjustable, electronic thermostat controls temperature from 100° F. to 425° F.
Fast heat-up and recovery time
Two pilot lights indicate power on and temperature cycling
Spring assist cover with adjustable vent and full width handle
On/off switch
Four stainless steel, level adjustable feet
Serviceable from front
Splash proof controls
Anti-splash pouring lip
OPEN BASE
GAS MODELS
SGL-30-TR
SGL-40-TR
MODULAR
SGM-30-TR
SGM-40-TR
ELECTRIC MODELS
SEL-30-TR
SEM-30-TR
SEL-40-TR
SEM-40-TR
30 gallon, 91,000 BTU, 36˝ wide
40 gallon, 130,000 BTU, 48˝ wide
30 gallon, 14 kW, 36˝ wide
40 gallon, 18 kW, 48˝ wide
SGL-30-TR
Power Pan™ Series Tilting Skillets
• 12 gauge, 304 stainless steel pan construction
• 5⁄8˝ mild steel clad bottom plus a 1⁄16˝ stainless steel plate for even temperature distribution
• Bead blasted cooking surface prevents food from sticking
• Low 35˝ rim height for easy operation and cleaning
• Easy-to-turn manual hand tilt, optional power tilt with manual override available
• Splash proof controls and construction
• Open base design for easy cleaning and maintenance
• Spring-assist cover with full width handle and vent
• Available with optional 2” tangent draw-off valve (TD2)
GAS MODELS
• Electronic “spark ignition system”
• Exclusive ultra efficient power burner (forced-air) gas combustion system
with automatic ignition
• Exclusive dual power settings:
90,000 and 125,000 BTU for 30 gallon;160,000 and 200,000 BTU for 40 gallon
ELECTRIC MODELS
• Standard voltages 208-240V 1 and 3 ph.
• High efficiency heating system:
12 kW for 30 gallon;18 kW for 40 gallon
• Available with high Wattage Option (HW)
16 kW on 30 gallon; 24 kW on 40 gallon
GAS
SGL-30-T1
SGL-40-T1
238
222_241NAFEDcat.indd 238
ELECTRIC
SEL-30-T1
SEL-40-T1
30 gallon, 391⁄8” wide
40 gallon, 511⁄8” wide
SHOWN WITH
OPTIONAL DOUBLE
PANTRY FAUCET
238
9/26/07 4:24:17 PM
Vortex® 100 Connectionless Steamer
STANDARD VORTEX® 100 PERFORMANCE FEATURES
• Convection fan circulates steam throughout the cooking cavity for even cooking pan to pan
• Reversible doors for left-hand and right-hand opening
• Push-up door latch for ease of operation
• Easy clean with bright interior finish
• Electronic timer with buzzer
• 4-gallon water reservoir
• Hands free push up door latch for ease of operation
• Easy to use diagnostics that automatically indicate when
the steamer is not operating at optimal performance
• ENERGY STAR® rated - eligible for ENERGY company rebates
VRC-3/6E FEATURES
• 208, 240 and 480V operation with plug/cord included
• Left-hand or right-hand door opening/field reversible
VRC-3E
VRC-6E
VRC-6E
Holds (3) 12˝ x 20˝ x 21⁄2˝ Pans
Holds (6) 12˝ x 20˝ x 21⁄2˝ Pans
SmartSteam™ 100 Boilerless Steamer
Equipment
Steamers, Kettles & Braising Pan
STANDARD SMARTSTEAM™ 100 PERFORMANCE FEATURES
• "Bad-water" proof – uses poor quality tap water, never requires conditioned water or deliming
• Single point water and drain connection (all models)
• Convection fan circulates steam throughout the cooking cavity for fast, even cooking from pan to pan
• Slide-out steam lid allows adding cold pans without lowering cavity or water temperature
• Easy-clean, mirror finish interior • Hands free push up door latch
• Low water consumption • 2 year warranty
SSB-( )E SMARTSTEAM™ 100 ELECTRIC FEATURES
• Generates more power: 3-pan 9 kW; 5-pan 12 kW; 10-pan 21 kW
• Heating element never immersed in water – providing longer life, uniform heat distribution, higher
energy utilization and no deliming
SSB-( )G SMARTSTEAM™ 100 GAS FEATURES
• Produces more BTUs per cavity with 3-pan 54,000 BTU, 5-pan 62,000 BTU and 10-pan 100,000 BTU
• State-of-the-art infrared burners – use gas more efficiently with more uniform heat distribution and less
wasted energy
ELECTRIC
SSB-3E/EF
SSB-5E/EF
SSB-10EF
(2)SSB-3EF
(2)SSB-5EF
(2)SSB-10EF
GAS
SSB-3G/GF
SSB-5G/GF
SSB-10GF
(2)SSB-3GF
(2)SSB-5GF
(2)SSB-10GF
Table Top/Floor Model Holds (3) 12˝ x 20˝ x 21⁄2˝ Pans
Table Top/Floor Model Holds (5) 12˝ x 20˝ x 21⁄2˝ Pans
Floor Model
Holds (10) 12˝ x 20˝ x 21⁄2˝ Pans
Floor Model
Holds (6) 12˝ x 20˝ x 21⁄2˝ Pans
Floor Model
Holds (10) 12˝ x 20˝ x 21⁄2˝ Pans
Floor Model
Holds (20) 12˝ x 20˝ x 21⁄2˝ Pans
Steam Jacketed Kettles
STANDARD FEATURES:
• Great for soups, stews, pasta and vegetables
• Self-contained
• Water resistant
• Electric or gas heated steam source
• 2⁄3 jacketed construction
• Counterbalanced manual tilt
or smooth action hand crank
• Reinforced bar rim and butterfly
shaped pouring lip
• Precise thermostatic
temperature control
DIRECT STEAM, CABINET
MOUNTED, WALL MOUNTED &
COOKER MIXER KETTLES ALSO AVAILABLE
ELECTRIC
GAS
TDB/6
N/A
Table Top, Tilting
TDB
TDH
Table Top, Tilting
TDBC
TDHC
Table Top, Crank Tilt
DEE/4
DH
Floor Mounted, Tilting
EE
AH/1
Floor Mounted, Stationary
Eclipse™ Tilting Braising Pan
TDBC SHOWN
WITH OPTIONAL
TS-9 STAND
& OPTIONAL
DRAIN CART
• Ergonomic, hard working and so versatile it can braise,
grill, hold, steam or cook just about anything
• Heats to 350° in just minutes
• Water resistant - less susceptible to water splash
back or spray
• Heavy-duty fully adjustable counterbalanced cover
with condensate drip shield and cover vent
• 40 gal. pan is 48˝w. and 30 gal. pan is 381⁄2˝w.
• Available in gas or electric
BPM Manual Crank Tilt
BPP Electric Tilt
10 qt.
20, 40 qt.
20, 40 qt.
20, 40, 60 gal.
20, 40, 60, 80, 100 gal.
TS/9*
Stand, 28˝ x 171⁄2˝h.
20 & 40 qt.
*Available with bullet feet or casters, drain cart sold separately
222_241NAFEDcat.indd 239
(2)SSB-5EF
SHOWN WITH
OPTIONAL
CASTERS
BPM-40
SHOWN
239
9/26/07 4:24:20 PM
Equipment
Sectional Equipment Battery
Platinum 32 - The NEW Standard in Sectional Equipment Batteries
Southbend sectional batteries are designed to withstand the rigors of high-volume restaurants, hotel kitchens, and institutional kitchens.
Heavy duty ranges, griddles, charbroilers, stock pot ranges, fryers, and broilers can be combined for a 100% custom line-up to fit the
needs of any high-volume operation.
Spray hose mounted on 4˝
spreader cabinet or pot fill faucet 2-year warranty on operational parts
on front rail
and 1-year labor
Choice of three shelves: (available in single or double)
– Solid
– Tray
– Tubed
Signature Broiler mounted
on convection oven
Standard and Convection
Ovens – 45,000 BTU with
electronic ignition standard
Free Battery Design Assistance
Ranges can be mounted
on cabinet, standard
or convection oven or
refrigerated base
Four 20,000 BTU burners with
Hi/Lo setting and removable
steel plate with 700˚F surface
temperature
Continuous 9˝
front rail standard
– optional 7.25˝
front rail with square
belly bar
Four 20,000 BTU burners with
1˝ thick griddle plate, side
splashers and stainless steel
grease drawer
Standard oven interior is large
enough to fit 26˝ x 26˝ sheet
pan either way
Porcelain oven interior standard.
Optional stainless steel interior
80,000 BTU charbroiler with removable cast iron
grates and uniform cooking surface up to 600˚F. Can
be mounted on any base. Field convertible from cast
iron radiants to lava rocks
33,000 BTU and
Signature 45,000 BTU
non-clogging burner
Removable cast
iron grates large
enough to fit
stock pot
Front and Rear
gas connection
– standard
Heat resistant
handle
240
Stainless steel cabinet
base with dual side by
side removable doors and
optional shelf
222_241NAFEDcat.indd 240
240
9/26/07 4:24:24 PM
300 Series Ranges
•
•
•
•
•
•
•
•
•
•
Patented 26,000 BTU clog-free burner
32,000 BTU standard oven/30,000 BTU convection oven
Stainless steel front rail and shelf
Deep standard oven holds sheet pans in both directions
Removable cast iron, flush top grates
Single piece drip tray under burners
On/Off switch for convection oven
Heat resistant door handle
Hinged lower valve panel
24/7 warranty
Equipment
Ranges
SHOWN WITH
OPTIONAL
CASTERS
400 Series Ranges
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Patented 33,000 BTU clog-free burner
45,000 BTU standard oven/30,000 BTU convection oven
Individual cast iron grates with 15˝ rear section
Heavy cool-to-touch handle
Front serviceable
Stainless steel front rail
Deep standard oven holds sheet pans in both directions
Coved interior
Lift-out porcelain oven bottom
Single piece drip tray under burners
On/Off switch for convection oven
High impact knob with set screw
Factory installed regulator
24/7 warranty
SHOWN WITH
OPTIONAL
CASTERS
SHOWN WITH OPTIONAL
CASTERS
222_241NAFEDcat.indd 241
241
9/26/07 4:24:28 PM
Equipment
Ventilation System
EcoArch Energy Efficient
Ventilation System
THE MOST ENERGY EFFICIENT VENTILATION SYSTEM.
The Avtec EcoArch is an economical and environmentally
safe solution to the need for high-quality, cost effective
ventilation performance in today’s foodservice kitchens.
The EcoArch ventilation system addresses the growing
need to reduce the amount of conditioned air from a
kitchen space. The combination of the patent pending
arch top and the front mounted high velocity exhaust
slot reduces the amount of exhausted CFM by 45%
compared to traditional CFM rates. This translates into an
annual electric and gas savings of up to 40%.
NOW THAT’S MAXIMIZING YOUR ENERGY
AND COST SAVINGS!
The Avtec EcoArch is the latest addition in the premium
systems that continue Avtec’s reputation as an innovative,
technology leader focused on providing solutions for our
customer’s needs.
FRONT MOUNTED EXHAUST PLENUM
The EcoArch is different from almost all other kitchen
exhaust hoods on the market today. The exhaust plenum
is in the front of the hood versus the traditional rear
location to minimize exhausted kitchen air and for easier
and safer access to the filter medium for cleaning and/or
replacement.
HIGH VELOCITY EXHAUST SLOT
Locating the high velocity slot as close to the top of the
hood as possible allows the arched top to easily direct
the contaminated heated air directly into the exhaust plenum. The slot is designed to create a rate of speed faster than the updraft
velocities developing from the cooking process. The higher rate of speed, in conjunction with the arch,
is the key to successfully capturing contaminated air at very low exhaust requirements.
EXCLUSIVE AERODYNAMIC ARCH
The arch dramatically reduces the amount of turbulence by directing contaminated heated air into the front location exhaust plenum.
In contrast to traditional hoods, testing indicated that about 70% of the heated air is immediately exhausted out of the reservoir area.
The remaining air is directed back by the arch towards the rear of the hood with little or no turbulence until it can be exhausted.
Preventative Maintenance Can . . . Save You Money, Extend the Life of Your
Equipment, Prevent Food Safety Hazards & Possible Downtime!
GENERAL PREVENTATIVE MAINTENANCE CHECKLIST:
✔ Are hinges, handles, knobs, grates, etc., all in good condition?
✔ Does the gas-fired equipment burn a steady blue flame?
✔ Are motors noisy or don’t turn at all?
✔ Are temperatures within ±5°F. of the desired setting?
✔ Are door gaskets worn or torn?
✔ Is water-feed equipment delimed on a periodic basis?
✔ Is the hood system operating?
✔ Are hood filters clean?
✔ Is the fire suppression system operational?
✔ Has the fire suppression system been inspected recently?
✔ Are all utilities working properly and resets checked?
-Source: www.cfesa.com
THINGS TO AVOID:
• Hosing down equipment
• Neglecting filter changes
• Improper application or use
• Operating equipment with frayed, burnt power cords or
exposed wiring
• Operating any equipment without knowing proper operation
and use as outlined in owner’s manual
242
-Source: www.cfesa.com
242_261NAFEDcat.indd 242
RANGE CHECKLIST:
✔ Check that rear flue is on the range
✔ Keep burner valves greased and inspect for cracks
✔ Keep burner parts clear and open
✔ Avoid standing on oven doors
✔ Check that oven racks are level and that the doors close tightly
✔ Make sure gas cocks turn smoothly
CONVECTION OVEN CHECKLIST:
✔ Avoid overloading the oven
✔ Check that the snorkel tube is not blocked
✔ Inspect the blower wheel for obstructions
✔ Check door openings and closings for proper alignment
and seal
✔ Ensure temperatures stay within 15° of 350°F.
✔ Verify that the cool-down is operational with the door open
and closed
✔ Avoid using scouring powder or pads on glass; clean door
gaskets and oven interior every day with warm soapy water
✔ Check to make sure the flue is free of all obstructions when
the oven is in operation
✔ Make sure gas units on casters have a restraining device to
prevent gas line breaks
242
9/26/07 4:30:38 PM
Gas Connector Kits for
Gas Equipment
• Kit contains all accessories required to be in
compliance with American Standard ANSI
Z21.69 and Canadian Standard C.G.A.
6.16-M87, including a full port valve, quick
disconnect and elbows
• Easier to connect moveable foodservice
appliances to gas utility lines with the Safety
System gas appliance connector kit
• Installation instructions, restraining device and
mounting hardware are included in the kit
1650 KIT
1675 KIT
16100 KIT
16125 KIT
1
⁄2˝ Diameter Hose
⁄4˝ Diameter Hose
1˝ Diameter Hose
11⁄4˝ Diameter Hose
3
CONSIDER PURCHASING EQUIPMENT WITH CASTERS AND
USING FLEXIBLE GAS APPLIANCE CONNECTORS TO IMPROVE SANITATION
AND SAFETY IN YOUR KITCHEN. IN A TYPICAL
FIXED INSTALLATION, THE DEAD SPACE BEHIND EQUIPMENT IS
INACCESSIBLE TO CLEANING. CASTERS AND FLEXIBLE
CONNECTORS ALLOW EQUIPMENT TO BE SAFELY AND
EASILY MOVED SO THAT REGULAR CLEANING IS EASY.
SafetyQuik®
and SwivelMax™
Gas Connector Kits
• Provide the safest gas connection possible
• Combines the most control of gas flow and
the widest range of motion available into
one convenient kit
SAFETYQUIK® W/SWIVELMAX™ FITTING
1
1650 KITCFS
⁄2˝ Diameter Hose
3
1675 KITCFS
⁄4˝ Diameter Hose
16100 KITCFS
1˝ Diameter Hose
SAFETYQUIK® W/2 SWIVELMAX™ FITTINGS
1
⁄2˝ Diameter Hose
1650 KITCF2S
3
1675 KITCF2S
⁄4˝ Diameter Hose
16100 KITCF2S
1˝ Diameter Hose
Posi-Set™
• Wheel placement system for
commercial cooking equipment
• Flame retardant thermo plastic resin, able
to resist 500 p.s.i. of direct force
• Ensures that specific cooking equipment is
replaced in the proper location after
removal for cleaning
• Can be installed in new and existing applications
• Installation hardware included • 93⁄4˝ x 41⁄4˝ x 1˝
• Can be added to any “BPQR” or “KIT” series hose - Just
add PS to the end of the part #
PSOne Set of Posi-Set™ - Bagged
3
⁄4˝ x 48˝ Connector Kit w/Posi-Set™
1675KIT48PS
3
16675KITS48PS
⁄4˝ x 48˝ Connector Kit w/SwivelMax™ & Posi-Set™
3
1675KIT2S48PS
⁄4˝ x 48˝ Connector Kit w/Double SwivelMax™ &
Posi-Set™
1675KITCF2S48PS 3⁄4˝ x 48˝ Connector Kit w/Double SwivelMax™,
SafetyQuik™ & Posi-Set™
242_261NAFEDcat.indd 243
Countertop Appliance Connectors
• Specifically designed to convey natural or LP gas to appliances
that are located on a counter top or peg-leg appliance stand
• Keeps kitchens safe and in compliance with
new industry codes and standards
• Kit includes 1⁄2˝ elbow, 3⁄4˝ x 1⁄2˝ reducing elbow
and 1⁄2˝ full port gas ball valve
• 1⁄2˝ I.D.
CT1650KIT24
CT1650KIT36
Equipment
Gas Connectors
24˝ length
36˝ length
Safety™ Quik Fitting
Safety Quik QDV, the first and only Quick-Disconnect Valve
combination fitting designed for the foodservice industry, meets the
safety and operational needs of commercial kitchens. Safety Quik
does the work of both the quick-disconnect and the valve.
• Innovative safety-sleeve, incorporates added
safety design features
• With Safety Quik, the gas connector can not be disconnected
until the gas valve is shut off, and can not be opened until the
gas connector is attached
CF50
CF75
CF100
1
⁄2˝ Diameter Hose
⁄4˝ Diameter Hose
1˝ Diameter Hose
3
SwivelMax™
Multi-Plane
Fittings
• Dramatically increases the
mobility of caster-mounted
equipment
• With 360° of spherical movement, the SwivelMax™ allows easy
movement of caster-mounted equipment back-and-forth, from
side-to-side and diagonally without locking up
• Safer gas connection by preventing crimping and tearing at the
ends of the gas connector that could cause potential leaks
• SwivelMax™ fittings are available in Dormont Gas Equipment
Installation Kits
S50
S75
S100
S125
1
⁄2˝ Diameter Hose
⁄4˝ Diameter Hose
1˝ Diameter Hose
11⁄4˝ Diameter Hose
3
243
9/26/07 4:30:39 PM
Equipment
Ranges
Performer S Series
Gas Restaurant Range
•
•
•
•
•
•
60˝w. x 32˝d. x 433⁄8˝h.
Stainless steel front, sides and front plate rail
6˝ chrome plated adjustable legs
Six one-piece, cast iron open burners
32,000 BTU per burner (NAT), 28,000 BTU per burner (PRO)
One 24˝w. broiler/griddle with 5⁄8˝ thick steel plate with manual
valve control and 3˝w. drip trough
• Two 26˝ ovens with range of low to 500°F.
• Ovens have one chrome plated oven rack with four position
removable rack guides
• 1 year limited warranty on parts and labor
PS-6-24BG-2626
Starfire Series Gas
Restaurant Ranges
• The famous even heating star burner now
delivers 24,000 BTU’s* for faster cooking
• The standard rugged cast iron top
sections can be substituted with black
porcelainized steel top sections
• Choose optional 12˝ hot top sections
and griddles in widths from 12˝ to 72˝
• Contoured stainless steel front rails
level with the top surface, stainless steel
backguard/plate shelf, 5⁄8˝ thick griddles
with spatula-width grease troughs and
accurate FDO oven thermostats are a
few of the outstanding features offered
on the Starfire Series line
* NATURAL GAS RATING. PROPANE WILL
YIELD AN IMPRESSIVE 20,000 BTU
H286
SHOWN WITH
OPTIONAL
CASTERS
H289
WITH STARFIRE BURNERS
24˝ WIDE RANGES
H28
24˝ w., 4 open burners,
H28S
24˝ w., 4 open burners,
36˝ WIDE RANGES
H286
36˝ w., 6 open burners,
H286S 36˝ w., 6 open burners,
48˝ WIDE RANGES
H288
48˝ w., 8 open burners,
H288S 48˝ w., 8 open burners,
1 open storage compt.
1 space-saver oven
1 open storage compt.
1 standard oven
1 open storage compt.
2 space saver ovens
1 standard oven,
WITH STARFIRE BURNERS
60˝ WIDE RANGES
H284
60˝ w., 10 open burners, 2 standard ovens
H287
60˝ w., 10 open burners, 1 standard oven,
1 open storage compt.
H283
60˝ w., 6 open burners, 2 standard ovens,
24˝ wide raised griddle/broiler
H282
60˝ w., 6 open burners,
1 standard oven, 1 open storage compt.,
24˝ w. raised griddle/broiler
72˝ WIDE RANGES
H289
72˝ w., 12 open burners, 2 standard ovens
H289S 72˝ w., 12 open burners, 1 standard oven,
1 open storage compt.
SunFire® Series Gas Restaurant Range
•
•
•
•
•
•
•
•
36”w. x 331⁄8”d. x 321⁄2”h.
Stainless steel front, sides and 41⁄2˝ plate rail
6˝ chrome plated adjustable legs
Six one-piece, cast iron open burners
28,000 BTU per burner
30,000 BTU/hr. oven
Thermostat with temperature range of low to 500°F.
One chrome plated oven rack with two position
removable rack guides
• Strong, keep-cool oven door handle
• 1 year limited warranty on parts and labor
244
MANY OTHER SIZES AVAILABLE!
242_261NAFEDcat.indd 244
SX-6-26
244
9/26/07 4:30:43 PM
Cuisine Series Heavy Duty 36˝ Gas Ranges
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Stainless steel front and sides
30,000 BTU open burners
One-piece, cast iron, lift-off top grates
Automatic lighting – all burners
6˝ stainless steel stub back
36˝ wide x 36˝ deep
100% safety oven pilot
Stainless steel valve panel
3-position rack guides w/1 oven rack
Stainless steel tubular legs on modular models
One-year parts and labor warranty
11⁄4˝ front gas manifold
Available in all standard top configurations
Optional 1˝ thick griddle plates
C836-6RC
SHOWN WITH
OPTIONAL
CASTERS
moisture+™ Oven
Equipment
Ranges & Ovens
A FULL-SIZE, MULTIFUNCTION OVEN
• Solid state control (temp. range 150˚F (66˚C) to 500˚F (260˚C))
• 100 hour, electro-mechanical timer and automatic moisture injection
• Two-speed fan with 3⁄4 hp. motor • All stainless construction
• Stainless steel oven interior with coved corners
• Shower stall style cavity base with drain
• Single door with “Split” window for easy cleaning • Quartz illumination
• 24” cooking cavity height • Six oven racks with 13 position rack guides
• “Pull-Out” control section for easy maintenance & service
• Service accessibility from front (all but water system)
• Double stack model available
• One year limited parts and labor warranty
GAS-FIRED
GAS - SPECIFY NATURAL OR LP
MP-GS-10-S
Standard Oven, Single Deck
MP-GS-20-S
Standard Oven, Double Deck
FOR DEEP DEPTH OVEN CHANGE “GS” TO “GD”
ELECTRIC - 11KW, 208 OR 240V
MP-ES-10-S
Standard Oven, Single Deck
MP-ES-20-S
Standard Oven, Double Deck
FOR DEEP DEPTH OVEN CHANGE “ES” TO “ED”
The Master™ Full-Size Gas Convection Oven
• Master 200 Solid State Control with 150° F (66°C) to 500°F (250°C)
temperature range and electromechanical timer
• Electronic spark ignition, including
automatic pilot system with 100%
safety shut off
• 2-speed fan control (high & low)
with 3⁄4 hp. fan motor
• Total of 60,000 BTU (17.6 kW)
loading per oven cavity
• Natural or propane gas
• Stainless steel front, sides, top, and legs
• 60/40 dependent door design with
double pane thermal window in both
doors and interior lighting
• Full Length, stainless steel positive
door closure
• Patented “Safety Door System”
MCO-GS-10-S
• Porcelain enameled oven interior with
SHOWN WITH
coved corners
OPTIONAL
• 24” cooking cavity height w/6 chrome
plated oven racks on 13-position rack guides CASTERS
• 1 year limited parts & labor warranty (USA & Canada only)
• 5 year limited door warranty, excluding window (USA & Canada only)
SINGLE DECK - 38” w. x 57” h.
MCO-GS-10-S 39” d.
MCO-GD-10-S 43” d.
242_261NAFEDcat.indd 245
DOUBLE DECK - 38” w. x 701⁄2” h.
MCO-GS-20-S 39” d.
MCO-GD-20-S 43” d.
Sunfire Series Gas
Convection Ovens
• Stainless steel front; 40” width
• Fully porcelainized oven interior
w/coved corners
• Solid state control with
60 minute timer
• Two speed, 3⁄4 hp. fan motor
• Electronic spark ignition
• 60/40 doors w/lights & windows
in both doors
• Dependent doors
• Temperature range: 200°F to
500°F (93°C to 260°C)
• 1 year parts and labor warranty
• Specify natural or propane gas
SDG-1
GAS-FIRED
GAS - 43˝ DEEP DEPTH
SDG-1
Full size, single deck, 80,000 BTU/23.4 kW total
SDG-2
Full size, double deck, 160,000 BTU/46.8 kW total
ELECTRIC - 43˝ DEEP DEPTH
ICO-E-10-M
Full size, single deck, 11 kW total, 208 or 240V
ICO-E-20-M
Full size, double deck, 22 kW total, 208 or 240V
245
9/26/07 4:30:48 PM
Equipment
Fryer Filters & Griddles
Fryer
Filtration Systems
FM-14
SHOWN WITH
(2) MX-14E
FRYERS
• Straight forward, hands free, and simple to operate
• Keep your shortening clean and produce a top quality tasting product
• Cost savings pay for the filter system in less than 1 year
• All Anets filter systems are engineered with the same easy to use design
• All quick disconnect assembly for thorough cleaning
• Stainless steel tank removes and can be put through dish machine
• Filter unit rolls completely out of fryer cabinet
• Motor is mounted on roll out filter unit and is equipped
with a cord, plug and power switch
• By adding the optional hose, the unit may be relocated
and plugged in for shortening disposal
• This also allows the unit to be used as a portable filter
• Anets filter element uses envelope filter paper to
eliminate clogging
• Filter intake draws shortening from the top and bottom
leaving virtually no shortening residue
• Adaptable to multiple screen options (paper, standard, carbon)
FM-14
100 lb. cap. filter for use under minimum of (2) 14˝ fryers
FM-18
120 lb. cap. filter for use under minimum of (2) 18˝ fryers
NOTE: MAY BANK UP TO 4 ADDITIONAL 14˝ OR 18˝ FRYERS IN ANY COMBINATION ON EITHER MODEL
FILT II-14
100 lb. cap. filter for use w/14˝ fryers
FILT II-14W
100 lb. cap. filter w/Crispy Food Warmer for use with 14˝ fryers
FILT II-18
120 lb. cap. filter for use w/18˝ fryers
FILT II-18W
120 lb. cap. filter w/Crispy Food Warmer for use with 18˝ fryers
NOTE: MAY BANK UP TO SIX, 14˝, 18˝ OR 20˝ FRYERS TO FILTRONIC II
FFM80
Portable filter, 80 lb. shortening capacity (not shown)
FFM150
Portable filter, 150 lb. shortening capacity (not shown)
FILT II-14W
SHOWN WITH
(2) MX-14E FRYERS
Gas Griddles
ANETS HAS SEVERAL COMBINATIONS OF GRIDDLES
AVAILABLE FOR A WIDE VARIETY OF APPLICATIONS
• The SLMG SERIES has manually operated burners
• The AG SERIES has thermostatically controlled burners
• The AGC SERIES adds a hard chrome finish to the
thermostatically controlled models
• Labor saving open side grease drawer models available
• Cooking surface sizes include 24˝ deep and 30˝
deep and 24˝ wide to 72˝ wide models
• Available in LP
• All models available with optional stainless steel stand
• U-shaped burners located every 12˝ for recovery and even heat distribution
• 3⁄4˝ thick high nickel content plate – Lifetime warranty against cracking
• 30,000 BTU per burner (24˝d. models); 40,000 BTU per burner (30˝d. models)
• All welded cabinet and backsplash
• Snap action thermostat every 12˝ (AG and AGC models)
• Double front wall construction keeps the operator and kitchen cool
• Special options such as an 11˝ h. backsplash and lift off cutting boards
complete the griddle line
SLMG SERIES
SLMG24X24
SLMG24X36
SLMG24X48
---
AG SERIES
AG24X24
AG24X36
AG24X48
AG24X60
AG24X72
AGC SERIES
AGC24X24
AGC24X36
AGC24X48
AGC24X60
AGC24X72
24˝
24˝
24˝
24˝
24˝
x
x
x
x
x
24˝
36˝
48˝
60˝
72˝
cooking
cooking
cooking
cooking
cooking
surface,
surface,
surface,
surface,
surface,
60,000 BTU
90,000 BTU
120,000 BTU
150,000 BTU
180,000 BTU
AG24X48
AGC24X48
SHOWN WITH OPTIONAL
MOBILE STAND
30˝ DEEP GRIDDLES ALSO AVAILABLE - PLEASE ASK YOUR SALES REPRESENTATIVE!
246
CHROME GRIDDLES
The griddle plate goes through special hardening, grinding and polishing processes that produces a finish that micropenetrates the steel and
becomes one with the griddle plate. Chrome models are incredibly easy to clean, simply scrape, scrub and shine using Anets AllShine and
the provided griddle cleaning kit. Chrome finished griddles have unique properties that maintain more of the heat in the griddle, radiate
less heat into the kitchen therefore keeping your cook and kitchen cooler. The smooth finish assures no flavor transfer between loads. And
the easy to clean surface provides labor savings and improves employee retention.
242_261NAFEDcat.indd 246
246
9/26/07 4:30:52 PM
18AA
SHOWN WITH
OPTIONAL CASTERS
MAXIMIZE FRYING
CAPACITY WITH ANETS
GOLDENFRY HIGH
PRODUCTION SERIES
GAS FRYERS.
High Production Series Gas Fryers
• 18˝ and 20˝ wide tube type fryers
• Perfect for high production frying of fries,
chicken pieces and breaded products
• 150,000 BTU input assures quick recovery for heavy loads
• Tube type design provides maximum heat transfer and
the necessary recovery for the large fry area
18E
18EG
18AA
20E
20EG
70-100 lb. shortening capacity, 150,000 BTU
70-100 lb. shortening capacity, 150,000 BTU, gas operated thermostat
70-100 lb. shortening capacity, 150,000 BTU, twin automatic basket lifts
100-120 lb. shortening capacity, 160,000 BTU
100-120 lb. shortening capacity, 160,000 BTU, gas operated thermostat
MX14 Gas Fryers
Electric Fryers
• 111,000 BTU cooks
like 145,000 BTU
• High efficiency, high recovery
for great tasting fried foods
• Open vat easy to clean design
• Multitude of configurations
and options to meet
your kitchen needs
• Equipped with copper
flashed heat exchangers
which provide remarkable
temperature recovery
• Sealed construction immersion
type heating elements
• “Ribbon type” elements are
high temperature alloy with
a stainless steel sheath
• Heating elements lift up out of
open pot for easy cleaning
• Solid state thermostat for
precise temperature control
• Built-in circuit breaker,
redundant contactors and hi-limit
control for increased safety
14EL-17
SHOWN WITH
OPTIONAL
CASTERS
MX-14E
SHOWN WITH
OPTIONAL CASTERS
MX-14E
MX-14EG
MX-14AA
14˝ h. efficiency fryer
14˝ h. efficiency fryer w/gas operated thermostat
14˝ h. efficiency fryer w/twin automatic basket lifts
Equipment
Fryers
14EL-14
14EL-14AA
14EL-17
14EL-17AA
14˝
14˝
14˝
14˝
electric
electric
electric
electric
fryer,
fryer,
fryer,
fryer,
14kW
14kW w/twin automatic basket lifts
17kW
17kW w/twin automatic basket lifts
Gas Fryer
SLG40 Gas Fryer
• Open vat design with sloped sides
for easy cleaning
• Open access to deep and wide
cold zone to remove food particles
• 111,000 BTU input uses unique
cross fire burners to cook
like a 125,000 BTU fryer
• 4 sided heating system
provides maximum recovery
• Fully insulated cabinet
keeps the kitchen cool
• Extra large 11⁄2˝ full port
ball drain valve
• Available with any Anets
fryer filtration system
• Built to perform, totally reliable
and priced to purchase today
• Efficient heating system uses only 2
burner tubes to achieve 90,000 BTU
input giving you maximum recovery
while maintaining easy access to
the cold zone for ease of cleaning
• Elliptical shaped tubes provide
14% more heat transfer
area than oval tubes
• Center mounted thermostat
provides quick response to fry loads
14GS
•
•
•
•
LARGER SIZE AVAILABLE!
SLG100 Gas Fryer
150,000 BTU
Shortening capacity 70-100 lb.
Spark ignitor
Casters standard
247
242_261NAFEDcat.indd 247
9/26/07 4:30:56 PM
Equipment
Fryers
Decathlon Gas Fryer
Super Runner
Gas Fryer
• Specifically designed for economy
all-purpose frying
• Stainless steel frypot with
35-43 lb. fat capacity
• 105,000 BTU
• 14˝ x 14˝ frying area
• Cool zone traps particles and
prevents contamination of oil
• Thermo-Tube design heats oil
quickly, yet consumes less gas per
load of product cooked
• Mechanical thermostat eliminates
time lost in waiting between loads
– requires no electrical hook up
• Standard with stainless steel front,
door, backsplash/flue cover
• 6˝ adjustable steel legs
SR42G
SHOWN WITH
OPTIONAL CASTERS
• Specifically designed for frying chicken
and other breaded products
• Stainless steel frypot with
60-75 lb. fat capacity
• 150,000 BTU’s provide maximum
heat dispersion with minimum energy
consumption
• 18˝ x 18˝ frying area with large
cool zone
• Solid state Thermatron temperature
controls for rapid recovery –
eliminates wait time between loads
• Standard with stainless steel frypot
• Stainless steel front and sides
• 6˝ adjustable steel legs at front with
stationary rear casters
D60G
SHOWN WITH
OPTIONAL COMPUTER,
BASKET LIFTS AND
CASTERS
Flat Bottom Gas Fryers
Specifically designed for volume specialty frying... the ultimate units for delicate liquid batter
(tempura-style) and bulk cooking. Perfect for golden fried products such as tortilla chips, taco
shells, fish fillets and shellfish – broad surface area allows quantity frying for peak demand
periods. For this free-float type frying, shallow oil depth and flat bottom design are a must.
The smooth, flat bottom design accommodates hand utensils for easy product removal.
• Mild steel tank prevents sticking
• Thermatron™ solid state temperature control system
• 120,000 BTU
• Standard with stainless steel front, door and back riser
• 6˝ adjustable steel legs
1824G
SHOWN WITH
OPTIONAL PAN
1824G
45-70 lb. Fat Capacity
18˝ x 24˝ Frying Area
DIVIDER, MARINE EDGE
2424G
65-90 lb. Fat Capacity
24˝ x 24˝ Frying Area
TOP CAP AND CASTERS
Super Cascade™ Under Fryer Filter
•
•
•
•
•
•
•
•
•
•
93 lb. oil capacity
Space-saving filter which fits inside cabinet of two fryers
5 GPM filter pump (120V)
1
⁄3 hp. motor
Filter Starter kit: filtration powder sample, 25 sheets filter paper,
clean-out rod, gloves, cleaning brush
Top connecting strips
Internally plumbed oil drain and return lines
11⁄4˝ diameter one-point end connection rear manifold gas line
without shut-off valve (gas only)
Filter heater standard
11⁄2˝ drain line standard
85UFF
248
242_261NAFEDcat.indd 248
SHOWN WITH
OPTIONAL CASTERS
248
9/26/07 4:31:00 PM
Gas Fryer
Gas Fryer
ALL-PURPOSE ECONOMY FRYER
• Open-pot design, no tubes, easy to clean
• Deep cold zone
• 11⁄4˝ IPS ball-type drain valve
• Five-year limited warranty on stainless frypot
• No burner tube radiants to burn out, no
cleaning or adjusting air shutters
• Available in steel or stainless fry pot
GF14
SHOWN WITH
OPTIONAL
CASTERS
Gas Fryer
DESIGNED FOR HIGH-VOLUME FRYING
• 40-50 lb. fat capacity
• Open-pot design, no tubes, easy to clean
• Centerline thermostat, two-year limited
warranty
• 7 to 10 second response to loads, 1°
anticipating action reducing temperature
overshoot
• Deep cold zone
• 11⁄4˝ IPS ball-type drain valve
• Lifetime limited warranty on stainless frypot
• 120V
SHOWN WITH
OPTIONAL
MJ45E
COMPUTER &
CASTERS
MJ35
Gas Fryers
SHOWN WITH
OPTIONAL
CASTERS
DESIGNED FOR HIGH PRODUCTION FRYING
• Up to 50 lb. shortening capacity
• 80,000 BTU for maximum fuel efficiency
• Electronic ignition
• Centerline thermostat provides 7 to 10
second response to loads
• Solid state controller
• Open fry pot with no hard to clean tubes
• Deep cold zone
• Boil-out mode
• 120V
H55 & H55-2 (SPLIT POT)
H55
SHOWN WITH
OPTIONAL COMPUTER
& CASTERS
Shortening Disposal Units
Gas Fryer
DESIGNED FOR FRYING CHICKEN, FISH
AND BREADED PRODUCTS
• 60 - 80 lb. shortening capacity
• 150,000 BTU/hr.
• Centerline thermostat provides 7 to 10
second response to loads, accurate to 1˚
• Millivolt temperature control circuit
• Deep cold zone
• 11⁄4˝ IPS ball-type drain valve
• Open fry pot with no hard to clean tubes
MJCF
DESIGNED FOR ALL-PURPOSE FRYING
• 30 - 40 lb. shortening capacity
• 110,000 BTU/hr.
• Produce 65 lb. of french fries per hour
– frozen to done
• Millivolt temperature control circuit
• Centerline thermostat provides quick
response to loads, accurate to 1˚
• Open-pot design, no tubes, easy to clean
• Deep cold zone
• 11⁄4˝ IPS ball-type drain valve
Equipment
Fryers & Filters
SHOWN WITH
OPTIONAL
CASTERS
• Specifically designed for the removal of waste
oil from the kitchen
• Drain height of 95⁄8˝ (cover open) fits under
most fryers for direct draining
• Heavy-duty manual pump can empty 60 lb. of
oil in less than 60 seconds
• Pump located at convenient height
• 90-day warranty
• Large wheels provide easy transport of oil
• Also available in 90 lb. capacity (SDU90)
SDU50
SHOWN WITH
OPTIONAL
COMPUTERS
&
FOR GAS & ELECTRIC FRYERS
CASTERS
Specifically designed to reduce operational expenses by eliminating the need for additional
floor and storage space, and to increase the useful life of shortening, while ensuring
quality fried products. It is engineered with features that allow added convenience, easier
serviceability and allows for using three different filter mediums with one pan.
Frymaster’s FootPrint® PRO Filtration System
•
•
•
•
•
•
•
•
State-of-the art filter pan design has coved, easy-to-clean corners – save time and money
Large capacity filter pan design is light weight for easy removal
Filter pan designed on rails to clear floormats
Ample cleaning space when filter pan is removed
All the benefits of a Filter Magic® without taking up additional floor space
Space saving – saves hood expense, floor space
Convenient – self contained so you can filter more often
Labor Saving – sloped drain pan leaves minimal shortening
residue behind after filtering
• Increased diameter on oil pick-up tube prevents clogging
242_261NAFEDcat.indd 249
249
9/26/07 4:31:05 PM
Equipment
Fryers, Filters & Pasta Cookers
Electric Fryers
SPECIFICALLY DESIGNED
FOR HIGH-VOLUME FRYING
• 40-50 lb. fat capacity
• Deep cold zone
• 11⁄4˝ IPS ball-type drain valve
• Low watt density, long-life heating
elements (increased reliability)
• Open-pot design (split or full)
• Boil-out mode for easy cleaning
• Controller assures pinpoint
accuracy of shortening
temperature, extending
shortening life
• Elements have low-watt density
for increased reliability
GSMS
SHOWN WITH OPTIONAL CASTERS
RE-14
SHOWN WITH
OPTIONAL CASTERS
Spaghetti Magic Systems
®
• Delivers incredibly large amounts of quality cooked
pasta automatically, reliably and inexpensively
• Electronic programmable controls
• Stainless steel cookpot
• Enamel cabinet
• Bulk cooking basket
• Portion cup racks
• Swing away hot/cold rinse faucet
• Overflow drain removes excess water and starch
• Automatic basket lift feature
• 6˝ adjustable legs
• Optional auto-fill/starch skimmer available
8SMS
GSMS
Electric – Delivers 1080 (10 oz.) Servings
Reconstituted Pasta Per Hour
Gas – Delivers 1440 (10 oz.) Servings
Reconstituted Pasta Per Hour
8 kW
80,000 BTU
14 KW FRYERS - 70 LB. FRENCH FRIES/HOUR, FROZEN TO DONE
RE-14
Stainless Steel Pot
RE-14SD
Stainless Steel Pot & Door
RE-14SC
Stainless Steel Pot, Door & Cabinet
17 KW FRYERS - 80 LB. FRENCH FRIES/HOUR, FROZEN TO DONE
RE-17
Stainless Steel Pot
RE-17SD
Stainless Steel Pot & Door
RE-17SC
Stainless Steel Pot, Door & Cabinet
22 KW FRYERS - 90 LB. FRENCH FRIES/HOUR, FROZEN TO DONE
RE-22
Stainless Steel Pot
RE-22SD
Stainless Steel Pot & Door
RE-22SC
Stainless Steel Pot, Door & Cabinet
Decathlon Gas Fryers
• Maximize your profits and get superior results and higher
production by providing precise temperature control, rapid
recovery, and economical operation with this Thermo-Tube design
• Dean’s Thermatron solid state temperature control system,
accurate to within plus or minus one degree, makes sure that
your fryer responds to load demand as you add product
HD50G
HD60G
HD50G
250
242_261NAFEDcat.indd 250
50 lb. Shortening Capacity
80 lb. Shortening Capacity
HD60G
SHOWN WITH
OPTIONAL
COMPUTERS &
CASTERS
250
9/26/07 4:31:12 PM
Solstice™ Stand Alone
SG18S
SG14S
TUBE FIRED GAS FRYER
• Solstice burner/baffle design increases cooking
production, lowers flue temperature, improves working
environment and generates more production per BTU
than previous models
• Millivolt thermostat maintains selected temperature
automatically between 200˚F and 400˚F
• Deep cool zone traps food and debris prolonging oil life
and reducing taste transfer
• Standard with stainless steel fry tank, front,
door and sides
• Includes 9˝ adjustable legs
• Also available as a twin tank providing two 7˝ fryer tanks
in a 14˝ cabinet.
SG14S
SG14RS
SG14TS
SG18S
*EACH TANK
CAPACITY
40-50 lb.
40-50 lb.
20-25 lb.*
70-90 lb.
BTU/HR INPUT
110,000
122,000
50,000*
140,000
Equipment
Fryers
FRIES/HR
88 lb.
110 lb.
41 lb.*
120 lb.
Economy Tube Fired Gas Fryer
35C+
• Astro-Therm tubes, an exclusive Pitco design, permit over 50% more
heat to be transferred to the oil, limiting waits between loads
• Wide spacing between tubes at the center of fryer permits easy access by
hand to all areas below and between tubes for easy, simple cleaning
• Optional stainless steel tanks available
35C+
• 35-40 lb. mild steel tank, stainless steel front and door
• 90,000 BTU produces 63 lb. of potatoes raw to done in 1 hour
45C+
• 42-50 lb. mild steel tank, stainless steel front and door
• 122,000 BTU produces 85 lb. of potatoes raw to done in 1 hour
• IN ORDER TO PRODUCE CONSISTENTLY GOOD TASTING FOOD,
KEEP THE FRYING OIL FREE OF CONTAMINANTS – NEVER SALT FOOD OVER THE OIL…KEEP
FRYPOTS COVERED WHEN NOT IN USE…AND ALWAYS RINSE AND DRY THE POT THOROUGHLY
AFTER WASHING.
• PROPER OIL MANAGEMENT IS ESSENTIAL TO GETTING THE MOST FROM YOUR COOKING OIL…
AND REALIZING A NICE ANNUAL SAVINGS IN SHORTENING COSTS.
• KEEP YOUR FRYING OIL AT THE PROPER FRYING TEMPERATURE (340° TO 350°F). OTHERWISE, ITS
QUALITY WILL SUFFER AND BREAK-DOWN WILL OCCUR AT DOUBLE THE RATE FOR EVERY 10
DEGREES OVER 350°.
• TO PROLONG THE LIFE OF FRYING OIL, FILTER TWICE A DAY AND THEN ADD 10% NEW OIL.
251
242_261NAFEDcat.indd 251
9/26/07 4:31:16 PM
Equipment
Fryers & Filters
Solstice™ Electric Fryers
• Solstice electric fryers have all of the same great mix-andmatch capability of the extremely popular gas series
• The design of the Solstice Electric Fryer employs heating element
construction that keeps the element in a fixed position
• Fixed element design allows for the removal of costly
and failure-prone components that would normally
be found in a pivoting element assembly
• Standard with 17kW elements, or boost the
production capacity with optional 22kW.
17 KW INPUT
SE14S
SE14TS
SE18S
22 KW INPUT
SE14S
SE14TS
SE18S
*EACH TANK
CAPACITY
40-50 lb.
20-25 lb.*
70-90 lb.
FRIES/HR
75 lb.
45 lb.*
120 lb.
40-50 lb.
20-25 lb.*
70-90 lb.
100 lb.
58 lb.*
155 lb.
SE14/SE14T
SHOWN WITH OPTIONAL CASTERS
Solstice™ Solofilter
SOLSTICE™ SOLOFILTER
DON’T HAVE THE ROOM FOR A BATTERY OF FRYERS
BUT STILL NEED THE FILTRATION CAPABILITY?
• Same great filter system as the Solstice Filter
Drawer, but contained in a single fryer cabinet
• The Soltice SoloFilter fits the need by keeping
the filtration system inside the fryer cabinet
• SoloFilter is available for any Solstice
full size, standard efficiency fryer
BOTH THE FILTER DRAWER SYSTEM AND THE
SOLOFILTER ALLOW FOR FUTURE FRYER ADD-ON.
SHOWN WITH OPTIONAL CASTERS
Solstice™
Filter Drawer System
252
242_261NAFEDcat.indd 252
SOLSTICE™ FILTER DRAWER
SHOWN WITH OPTIONAL CASTERS
DRIVE COST OUT OF YOUR PRODUCTION WITH
THE PITCO SOLSTICE FILTER DRAWER SYSTEM
WITH BASKET LIFTS. BASKET LIFTS REDUCE
LABOR AND IMPROVE COOKING CONSISTENCY
WHILE FILTRATION CAN ADD 40 TO 50% TO
YOUR OIL LIFE.
• Solstice series gas and electric fryers
have been designed to improve
mix-and-match capabilities
• Choose between twin tank or full
size high production models, or
even a large 18˝ tank fryer
• The filter drawer is designed to fit under the
fryers so no extra floor space is required
• The filtration system consists of an extra
large 3˝ round drain line, 8 gallon per
minute oil pump and 1⁄2˝ dia return lines
for fast, easy to use, two step oil filtration
252
9/26/07 4:31:19 PM
Solstice™ Supreme High Efficiency Gas Fryers
Pitco’s newest series of fryers, the “Solstice Supreme”, are a major breakthrough in fryer design and efficiency. Our engineers
have designed a system that has the highest gas efficiency rating, combined with the lowest cost in the industry.
Pitco’s Solstice Supreme fryer category has more gas models than any manufacturer (25 lb., 50 lb., ect.) that achieve the
Energy Star rating.
The smart simple design eliminates all of the failure prone moving parts found in old technology high efficiency fryers. With
the push of a button, once a day, our matchless lighting system ignites a standing pilot. This begins a 30 second automatic self
cleaning burner procedure, which ensures optimal burner efficiency. This procedure ensures that the burners stay clean and
efficient all day, every day....PERIOD!
You now have the flexibility to mix and match any Supreme fryer and create your own custom design.
• Standard with solid state controller
• Combine any SSH55, SSH55T or SSH75
• Solstice™ Supreme filtration is designed with a 3˝ round drain line, 5 gallon per minute oil
pump and 1⁄4˝ return lines for filtering high volume, lightly or non-breaded products
SSH55-F
SSH55-T
SSH75-F
Full Tank
Twin Tank
Full Tank
CAPACITY
40-50 lb.
20-25 lb.
75 lb.
BTU
80,000
40,000
105,000
Equipment
Fryers
FRIES/HR
80 lb.
80 lb.
105 lb.
SSH75/SSH55/SSH55T WITH OPTIONAL
FILTER DRAWER AND CASTERS
253
242_261NAFEDcat.indd 253
9/26/07 4:31:24 PM
Equipment
Donut Fryers & Pasta Cookers
24R-UFM
WITH OPTIONAL CASTERS
24P
WITH OPTIONAL CASTERS
Donut Fryer
• Super efficient donut fryer produces high quality
donuts and bakery products with 33% less oil and
40% less BTU’s than conventional 24˝ donut fryers
• It also features advanced solid state thermostat with melt
cycle capability and a Spacefighter™ filtration system
• Electronic ignition is also available
• 72,000 BTU/hr
• Produces up to 80 dozen donuts per hour
• Oil capacity 100 - 117 lb.
Donut Fryer
24RUFM
24P
• Produces golden brown donuts,
cruller, drycakes and bismarks
• Large cool zone traps particles and crumbs,
prevents a major cause of fat breakdown
• Frying area is 24˝ x 24˝ x 41⁄2˝
• 120,000 BTU/hr
• Oil capacity 150 lb.
Pasta Perfect Cooker
AUTOMATED COOKING PROCESS PRODUCES PERFECT PASTA EVERY
TIME
• Precise, consistent results with automatic basket lifts
• Reconstitutes over 500/10 oz. servings per hour of pasta product
• Stainless steel cabinet with 11⁄4˝ drain valve
• Digital thermostat and controls
• Available in both gas (natural or propane) and electric
GAS
PG14D
ELECTRIC
PE14
CAPACITY
12 gal.
INPUT
77,500 BTU/hr
7 gal.
6kW - 208/240V
PPG-14D-L
SHOWN WITH OPTIONAL CASTERS
254
242_261NAFEDcat.indd 254
254
9/26/07 4:31:26 PM
Equipment Stands
•
•
•
•
Exclusive patented uni-lok® design for superior strength
Features 16 gauge type 304 stainless steel top with galvanized legs and adjustable undershelf
11⁄2˝ upturn on back and both ends • All equipment stands have three standard hat channels for extra support
72” long tables feature six legs for increased stability
24"D. STANDS
30"D. STANDS
WXL
T2436GS
T3036GS
243⁄8" x 363⁄16"
T2448GS
T3048GS
243⁄8" x 483⁄16"
T2460GS
T3060GS
243⁄8" x 603⁄16"
T2472GS
T3072GS
243⁄8" x 723⁄16"
OPTIONAL CUTTING BOARDS
307105
36" Length
8" wide, 11⁄4" thick laminated
307106
48" Length
maple top w/adjustable stainless
307107
60" Length
steel tubular supports.
307108
72" Length
SEE OUR SALES PERSONNEL FOR OPTIONS & ACCESSORIES
INCLUDING DRAWERS & A FULL RANGE OF TABLE STYLES
Equipment
Work Tables
Mixer Stands
• Highly polished 16 gauge type 304 stainless steel flat top
• Exclusive patented uni-lok® design for superior strength
• Available with choice of either galvanized legs & adjustable
undershelf or galvanized tubular base
• 24˝ working height
UNDERSHELF
MS2424
MS3024
MS3030
TUBULAR BASE
TMS2424
TMS3024
TMS3030
WXL
24" x 24"
30" x 24"
30" x 30"
Work Tables
• Exclusive patented uni-lok® system for superior strength
• All worktables 60˝ and longer come standard with three hat channels
• All tables prepunched including attachment bolts for installing drawer
assemblies
“B” SERIES WORK TABLES
“B” Series worktables feature all 430 stainless steel tops,
galvanized legs and adjustable galvanized undershelf.
FLAT TOP
T2436B
T2448B
T2460B
T2472B
T2496B
T3036B
T3048B
T3060B
T3072B
T3096B
4" BACKSPLASH
T2436B-BS
T2448B-BS
T2460B-BS
T2472B-BS
T2496B-BS
T3036B-BS
T3048B-BS
T3060B-BS
T3072B-BS
T3096B-BS
SIZE
24" x
24" x
24" x
24" x
24" x
30" x
30" x
30" x
30" x
30" x
36"
48"
60"
72"
96"
36"
48"
60"
72"
96"
“SEB” SERIES WORK TABLES
“SEB” Series worktables feature all 304 stainless
steel tops, legs & adjustable undershelf.
FLAT TOP
T2436SEB
T2448SEB
T2460SEB
T2472SEB
T2496SEB
T3036SEB
T3048SEB
T3060SEB
T3072SEB
T3096SEB
4" BACKSPLASH
T2436SEB-BS
T2448SEB-BS
T2460SEB-BS
T2472SEB-BS
T2496SEB-BS
T3036SEB-BS
T3048SEB-BS
T3060SEB-BS
T3072SEB-BS
T3096SEB-BS
SIZE
24" x
24" x
24" x
24" x
24" x
30" x
30" x
30" x
30" x
30" x
36"
48"
60"
72"
96"
36"
48"
60"
72"
96"
255
242_261NAFEDcat.indd 255
9/26/07 4:31:30 PM
Equipment
Sinks
Mop Sinks
• Floor mount for the ultimate in sanitation
• Exclusive anti-splash double-offset “V” edge reduces spillage
• Deep-drawn seamless bowl with 8" water depth
• All stainless steel construction provides long life and easy maintenance
• 211⁄2" wide x 245⁄8" long
F1916
ACCESSORIES FOR MOP SINK
312690
Service Faucet
312689
Hose & Bracket
312688
Mop Holder
Clean Dishtables
Clean dishtables feature
polished stainless steel work
surface. Crossbraced legs.
Adjustable non-marking bullet
feet. Available in 14 or 16
gauge stainless steel.
LEFT
CDTL-24
CDTL-30
CDTL-36
CDTL-48
CDTL-60
CDTL-72
RIGHT
CDTR-24
CDTR-30
CDTR-36
CDTR-48
CDTR-60
CDTR-72
24”
30"
36"
48"
60"
72"
LEFT
SDTL-36
SDTL-48
SDTL-60
SDTL-72
SDTL-96
RIGHT
SDTR-36
SDTR-48
SDTR-60
SDTR-72
SDTR-96
36”
48"
60"
72"
96"
Soiled Dishtables
Dishtable Package Special
Dishtable package includes 48˝ 16 gauge 304 stainless steel
clean dishtable and soiled dishtable, rubber scrap block,
prerinse faucet (part #300718), prerinse basket & slide bar,
and 42˝ KD tubular rack shelf. (Dishwasher not included.)
DTC-48LR-16/3 or DTC-48RL-16/3
Includes polished stainless steel
work surface. 20” x 20” x 5”
prerinse sink. Crossbraced
legs. Scrap block furnished. 8”
backsplash. 11⁄2” rolled rim on
open sides. Available in three
types of stainless steel (16 ga. 430 or 304 or 14 ga. - 304).
Work Tables With Flex-Master® Overshelf System
•
•
•
•
•
Eagle worktables & Flex-Master® Overshelf System are packaged in convenient kits; ready for immediate shipment
Table tops are predrilled for rear mounting of posts & shelves
Overshelf posts are stainless steel with grooves on 1˝ increments for flexible shelf placement
All tables feature exclusive patented uni-lok® design for superior strength
Available in 2 styles: “FM” Style includes four 30˝ stainless steel posts, & two 12˝ overshelves;
“FM-PL” Style includes two 30˝ stainless steel posts, two 48˝ stainless steel posts, two
12˝ stainless steel overshelves, & two pot racks.
SPEC-MASTER “SE” SERIES WORK TABLES
All stainless steel construction, including 14 gauge type 304 stainless steel top, stainless
steel legs, undershelf & feet.
“FM” STYLE
T3048SE-FM
T3060SE-FM
T3072SE-FM
“FMPL” STYLE
T3048SE-FMPL
T3060SE-FMPL
T3072SE-FMPL
SIZE
30" x 48"
30" x 60"
30" x 72"
“SB” SERIES WORK TABLES
16 gauge type 430 stainless steel top, stainless steel legs & undershelf, plastic feet.
“FM” STYLE
T3048SB-FM
T3060SB-FM
T3072SB-FM
“FMPL” STYLE
T3048SB-FMPL
T3060SB-FMPL
T3072SB-FMPL
SIZE
30" x 48"
30" x 60"
30" x 72"
“B” SERIES WORK TABLES
16 gauge type 430 stainless steel top, galvanized legs & adjustable
galvanized undershelf, plastic feet.
“FM” STYLE
T3048B-FM
T3060B-FM
T3072B-FM
256
242_261NAFEDcat.indd 256
“FMPL” STYLE
T3048B-FMPL
T3060B-FMPL
T3072B-FMPL
SIZE
30" x 48"
30" x 60"
30" x 72"
256
9/26/07 4:31:33 PM
Coved Corner Sinks
• All EAGLE coved corner sinks feature 91⁄2˝
backsplash, deep drawn seamless
coved corner bowls
• 14˝ water level
• Legs crossbraced front to back
• New Euro-style design includes new
Euro-style edging, new bowl design and
enhanced polishing techniques
414 SERIES feature heavy gauge stainless steel
construction, type 304 bowls and type 430
drainboards and backsplash.
314 SERIES feature heavy gauge stainless steel
construction, type 304 bowls, drainboards and
backsplash.
414 SERIES
414-16-1
414-16-1-18R OR L
414-24-1
414-16-2
414-16-2-18R OR L
414-16-2-18
414-22-2-24
414-16-3
414-16-3-18R OR L
414-16-3-18
414-22-3-24
414-24-3-24
314 SERIES
314-16-1
314-16-1-18R OR L
314-24-1
314-16-2
314-16-2-18R OR L
314-16-2-18
314-22-2-24
314-16-3
314-16-3-18R OR L
314-16-3-18
314-22-3-24
314-24-3-24
One comp, no drainboard
One comp, 18" drainboard R or L
One comp, no drainboard
Two comp, no drainboard
Two comp, 18" drainboard R or L
Two comp, two 18" drainboards
Two comp, two 24" drainboards
Three comp, no drainboard
Three comp, 18" drainboard R or L
Three comp, two 18" drainboards
Three comp, two 24" drainboards
Three comp, two 24" drainboards
OA Length
22"
393⁄4"
29"
39"
551⁄2"
72"
96"
57"
731⁄2"
90"
120"
126"
Bowl Size
20" x 16"
20" x 16"
24" x 24"
20" x 16"
20" x 16"
20" x 16"
22" x 22"
20" x 16"
20" x 16"
20" x 16"
22" x 22"
24" x 24"
Equipment
Sinks
Hand Sinks
• EAGLE hand sinks are the most specified in the industry
• Feature positive drain, deep drawn seamless stainless steel design
• A variety of models are offered, including basic units, units with
towel dispensers and all electronic units
• All models are wall mounted and include faucets
• A variety of models to choose from
HSA-10-F
HSAN-10-F
HSA-10-FL
HSA-10-FA
HSA-10-FO
HSA-10-FDP
HSA-10-FLDP
HSA-10-FE
HSA-10-FE-B
HSA-10-FDPE
HSA-10-FDPE-B
Basic Hand Sink w/Basket Drain
Narrow Hand Sink, 12" From Side to Side
Basic Hand Sink w/Lever Drain
Basic Hand Sink w/P-trap and Overflow
Basic Hand Sink w/Overflow
W/Towel & Soap Dispenser, Basket Drain
W/Towel & Soap Dispenser, Lever Drain
Basic Handsink w/Electronic Eye
Basic Handsink w/Battery Powered Electronic Eye
w/Electronic Eye on Sink, Towel & Soap Dispenser
w/Battery Powered Electronic Eye on
Sink, Towel & Soap Dispenser
Hand Sink With Waste Receptacle
• Includes splash mounted gooseneck faucet, towel and soap dispenser,
waste skirt, waste receptacle and basket drain
• Wall mounted
• Waste receptacle slides onto bottom of waste skirt
• Patented design
• Model shown with optional wrist handles
HSA-10-FDPS-T
Hand Sinks with Microgard® Antimicrobial Protection
• An antimicrobial agent which contains built in protection to retard the growth of a
broad range of bacteria, mold and mildew on the surface of bowl that cause stains, odors and degradation
• MICROGARD® is a second line of defense
• In keeping with good hygiene practices, clean this product as usual
• The protection will not wash out, while organic bactericides may
• Available on electronic eye handsinks
How to order MICROGARD® on handsinks:
To order, add suffix “-MG” to model (example: HSA-10-FE-B-MG)
See our sales personnel for Options & Accessories
257
242_261NAFEDcat.indd 257
9/26/07 4:31:36 PM
Equipment
Sinks
Utility Sinks
• Constructed of all 16 gauge stainless steel with roll rim partition, 14" deep
compartments and adjustable bullet feet
• 36" working height
• Crumb cup strainer standard
• Available in either type 430 or type 304 stainless steel (Non-NSF)
16/430 S/S
1818-1-16/4
2118-1-16/4
2124-1-16/4
2424-1-16/4
2136-2-16/4
2448-2-16/4
2136-3-16/4
2148-3-16/4
2154-3-16/4
2472-3-16/4
16/304 S/S
1818-1-16/3
2118-1-16/3
2124-1-16/3
2424-1-16/3
2136-2-16/3
2448-2-16/3
2136-3-163
2148-3-16/3
2154-3-16/3
2472-3-16/3
# OF BOWLS
1
1
1
1
2
1
3
3
3
3
BOWL SIZE
18" x 18"
21" x 18"
21" x 24"
24" x 24"
21" x 18"
24" x 24"
21" x 12"
21" x 16"
21" x 18"
24" x 24"
O.A. LENGTH
21"
21"
27"
27"
39"
51"
39"
51"
57"
75"
Cocktail Units
•
•
•
•
Type 304 stainless steel ice chest, stainless steel top, front & sides
Fully insulated with 60 lb. ice capacity
1800 Series underbar equipment measures 18" front to back
2200 Series measures 22" front to back
1800 SERIES
2200 SERIES
B2CT-18
B2CT-22
2' Cocktail Ice Chest
B3CT-18
B3CT-22
3' Cocktail Ice Chest w/Sliding Cover
B2CT-18-7
B2CT-22-7
2' Cocktail Ice Chest w/7-Circuit Cold Plate
B3CT-18-7
B3CT-22-7
3' Cocktail Ice Chest w/7-Circuit Cold Plate
B36IC-18
B36IC-22
3' Ice Chest - 125 lb. capacity
SEE OUR SALES PERSONNEL FOR OPTIONS & ACCESSORIES
Underbar Units
• All stainless steel top, front & ends
• Type 304 stainless steel 10˝ x 14˝ x 10˝ bowls, complete with
5˝ backsplash, 11⁄2˝ drains
• Faucets included
• 1800 Series underbar equipment measures 18" front to back
• 2200 Series measures 22" front to back
1800 SERIES
B5C-18
B6C-18
B6C4-18
2200 SERIES
B5C-22
B6C-22
B6C4-22
5' Bar Sink, 3 Bowls, 13" Drainboards
6' Bar Sink, 3 Bowls, 19" Drainboards
6' Bar Sink, 4 Bowls, 13" Drainboards
Convenience Store Sinks
•
•
•
•
•
•
Constructed of all 304 stainless steel bowls, drainboards and backsplash
36” working height
Deep drawn coved corner bowls
Legs crossbraced front to back
Three compartments.
Crumb cup strainer included
310 SERIES
310-10-3-12
310-10-3-18
312 SERIES
312-12-3-12
312-14-3-12
258
242_261NAFEDcat.indd 258
Three Comp., 10” Bowl, Two 12” Drainboards
Three Comp., 10” Bowl, Two 18” Drainboards
Three Comp., 12” Bowl, Two 12” Drainboards
Three Comp., 14” Bowl, Two 12” Drainboards
258
9/26/07 4:31:41 PM
Dormont Grease Interceptors
Don’t let grease and effluent cause problems with your drainage system.
Dormont offers a full line of PDI certified, epoxy coated, steel constructed
grease interceptors for installation on cooking/prep sinks, pot, pan,
scullery sinks and dishwasher applications.
WD-4
WD-7
WD-10
WD-15
WD-20
WD-25
WD-35
WD-50
8 lb. Grease Capacity
14 lb. Grease Capacity
20 lb. Grease Capacity
30 lb. Grease Capacity
40 lb. Grease Capacity
50 lb. Grease Capacity
70 lb. Grease Capacity
100 lb. Grease Capacity
10˝ w. x 11˝ h. x 16˝ l.
13˝ w. x 12˝ h. x 18˝ l.
14˝ w. x 12˝ h. x 213⁄4˝ l.
15˝ w. x 14˝ h. x 22˝ l.
153⁄4˝ w. x 15˝ h. x 24˝ l.
161⁄2˝ w. x 161⁄2˝ h. x 26˝ l.
18˝ w. x 19˝ h. x 30˝ l.
22˝ w. x 211⁄2˝ h. x 32˝ l.
Equipment
Grease Interceptors/Pre-Rinse Assembly
PRSH-S
POWERForce™ Pre-Rinse Assemblies
Dormont Manufacturing proudly offers the PowerForce™ line of commercial
faucets, drains and pre-rinse assemblies. Dormont’s commitment to
quality is reflected in the 2 year warranty that all Powerforce™ products
carry: the best in the industry. Dormont also offers a full range of
PowerForce™ replacement parts and accessories.
•
•
•
•
•
⁄4 turn full-on valves
Solid Brass Construction
Chrome-Plated Finish
100% Factory Tested
Tested and certified by WQA against NSF/ANSI 61,
Section 9 and ASME A112.18.1
1
PRE-RINSE
P-WS8B*
PRSH-S*
PRH-G44
Wall Mount, 8” Base
Spray Head Assembly
44”l. Replacement Hose
PRH-G44
*MEETS ENERGY POLICY ACT OF 2005; 1.6 GPM
WALL MOUNT FAUCET
F-WST8-S12S
8” Adjustable Center w/12” Swivel Spout
P-WS8B
F-WST8-S12S
259
242_261NAFEDcat.indd 259
9/26/07 4:31:46 PM
Equipment
Sinks & Underbar Equipment
n
n
n
n
Quality stainless steel underbar equipment
Design and layout assistance
Custom fabrication available
Delivery within 7-10 days
Sinks
Ice Chests & Cocktails
19˝ SERIES
SD24
SD30
SD36
19˝ SERIES
SD53C
SD63C
SD64C
Add-On Units
21˝ SERIES
SK53C
SK63C
SK64C
All Products Include:
• FAUCETS AND DRAIN ASSEMBLIES
• STANDARD 4˝ BACKSPLASH
• NSF APPROVED STAINLESS STEEL
CONSTRUCTION
HAND SINKS
BLENDER STATIONS
DIPPER WELL
260
242_261NAFEDcat.indd 260
21˝ SERIES
SK24
SK30
SK36
Glass Racks
SK24GR
CL24GR
(Smooth or drainboard
top available)
260
9/26/07 4:31:50 PM
B-0610 POT AND KETTLE FILLER:
• Wall mounted mixing faucet assembly
on 8” centers
• 1⁄2˝ IPS female inlets with vacuum breaker
connection for hose
• Five feet of polished flexible stainless steel hose
• Hook nozzle with self-closing valve
• Valve is furnished with retaining ring for
continuous flow of water if desired
• Hose hangs down approximately 32˝ from
faucet connection when not in use
• Built-in check valves to prevent cross flow of
hot and cold water
B-7222-CO1 RETRACTABLE HOSE REEL:
• Heavy-duty, 30 foot hose of 3⁄8˝ I.D. with
adjustable hose bumper
• Enclosed reel with epoxy
coated steel finish
• Spray valve with heat
resistant handle
• Ratcheting system
holds the length of
hose until a slight tug;
retracts automatically
• Multi-fit bracket for wall, ceiling or under-sink mounting
• 3⁄8˝ NPT female inlet
B-0107-C LOW FLOW SPRAY VALVE:
• T&S Brass led the industry with their
B-0107-C low flow spray valve,
which has been on the market for
nearly twenty years
• One of the easiest and most cost effective energy saving devices
available, it reduces water consumption, water heating energy
and sewer charges
• With a flow rate of 1.24 gpm, it has passed the ASTM test for
pre-rinse spray valves with an average cleanability rate of 21
seconds and is the only pre-rinse spray valve made that is
endorsed by the Green Restaurant Association
• Fully compliant with EPAct 2005 low flow standards and can be
used in place of the B-0107 with any T&S pre-rinse assembly
B-0231
SWIVEL BASE FAUCET:
• Wall mount mixing faucet
on 8˝ centers
• 1⁄2˝ NPT female eccentric inlet flanges,
lever handles, 12˝ swing nozzle with
stream regulator
B-0290 FAUCET:
• Delivers high volume
of water
• 12˝ swing nozzle
• 8˝ centers adjustable from 73⁄4˝ to 81⁄4˝
• With female 3⁄4˝ IPS model LL street EL inlets
with locknuts, to fit within 2˝ space behind splashback
• Removable seats • Four arm handles • (If street EL inlets not
required specify) When street ELs are removed, faucet has
3⁄4˝ IPS eccentric inlets to fit on front face of splashback
• 11⁄4˝ diameter holes required in splashback
EC-3101 CHEKPOINT ELECTRONIC
WALL MOUNT GOOSENECK FAUCET:
• Easy to install in any design
• Hands-free, sensor-operated faucets significantly
conserve water by shutting off during scrubbing, which
also greatly reduces the risk of cross-contamination
• The proven electronic technology is tested to exceed
500,000 washes and boasts a long battery life (2-3 years
with AA size batteries) and low-battery indicator light
• Made of chrome-plated brass and come
pre-assembled with all mounting hardware
• Additional features include a temperature control mixing
valve, vandal resistant aerator and 18˝ hot and cold supply
stop flexible connector hoses
• All models are AC/DC and are ADA compliant
242_261NAFEDcat.indd 261
Workboard Faucet with
Swing Nozzle
for Deck Mounting
• Bronze body with removable seats
• High luster chrome plated
brass escutcheon 61⁄2˝ long x 2˝ wide
• Shanks on 4˝ centers, 1˝
long, 1⁄2˝ NPS thread
• Heavy wall 6˝ tubular swing nozzle
B-1110
Pot and Kettle Filling Faucet
Equipment
Faucets & Pre-Rinse Units
• Wall mounted faucet for single temperature control
• 1⁄2˝ IPS female inlet
• 18˝ double-joint nozzle with insulated,
on-off control grip on tip of nozzle
B-0592
Push-Back Glass Filler
•
•
•
•
•
Heavy duty construction
Wall mounted – 3⁄8˝ IPS female inlet with adjustable flange
Volume regulator
Center of outlet to wall – 33⁄4˝
Translucent blue Lexan
push-back arm, instantaneous shut-off
B-1200
Pre-Rinse
Units With
Spring Action
Gooseneck
DECK MOUNT PRE-RINSE UNIT
• Deck type faucet has undersink mixing spreader with
built-in spring checks
• 1⁄4˝ IPS tailpiece connections on
4˝ centers
• 40˝ high
B-0113
B-0113
WALL MOUNT PRE-RINSE UNIT
• 1⁄2˝ IPS female eccentric
flanged inlets
• 8˝ center wall mounted faucet
• 34˝ high
B-0133
B-0133
261
9/26/07 4:31:54 PM
Equipment
Sinks/Underbar Stations
Insulated Ice Bins
•
•
•
•
•
Stainless steel interior, top, front, sides & backsplash
Removable bottle racks
Optional built-in 7 circuit cold plate available for soda system
Additional sizes available
1” drain
1800 SERIES
18-24
18-24-7
18-36
18-36-7
2100 SERIES
21-24
21-24-7
21-36
21-36-7
24”
24”
36”
36”
x
x
x
x
12”d.,
12”d.,
12”d.,
12”d.,
80 lb. Ice Cap.
w/Cold Plate (80 lb.)
115 lb. Ice Cap.
w/Cold Plate (115 lb.)
SHOWN WITH
OPTIONAL SPEEDRAIL
Cocktail Workstations
•
•
•
•
•
Complete workstation for added efficiency
Stainless steel top, front, sides and backsplash
Raised edges on drainboard to keep glasses dry
24” x 12” deep ice bin holds 80 lb. of ice
Large 18” blender/dump sink for two blenders
with a dump/hand sink in the rear
• Faucet and drains included
• Optional built-in cold plate for soda systems
listed below
1800 SERIES
18-W66R
18-W66R-7
2100 SERIES
21-W66R
21-W66R-7
5’6” Workstation
5’6” Workstation w/Coldplate
Underbar Sinks
• Quality construction built for durability
• Stainless steel top, front & backsplash
• Large 10” x 10” 304 series stainless steel sink bowls
with corner drains for increased bowl capacity
• Faucet, drains & stainless steel overflows included
• 1800 series depth 181⁄2”; 2100 series depth 21”
1800 SERIES
18-53C
18-63C
18-64C
2100 SERIES
21-53C
21-63C
21-64C
SHOWN WITH
OPTIONAL SPEEDRAILS
5’ Sink, 3 Bowls, 12” drainboards
6’ Sink, 3 Bowls, 18” drainboards
6’ Sink, 4 Bowls, 18” drainboards
Royal Series Underbar
• Free bar layout and design
• High quality Underbar built
for your individual needs
• Heavy duty construction with built-in sound
deadened speedrails and high quality faucets
• Stainless steel front, tops, sides, backsplashes
& legs
• Built-in high volume 8-circuit cold plate for
soda system with optional 10-circuit available
• Units pre-assembled at factory to
cut installation time
• Also available in Modular Bar design which
eliminates all legs
262
262_272NAFEDcat.indd 262
262
9/26/07 4:40:14 PM
Wall Mount Pre-Rinse
w/Add-On Faucet
•
•
•
•
•
Commercial Series
Wall Mount Faucet
• Built for medium volume use
• 8” center wall mount
12-808
12-810
12-812
12-814
8”
10”
12”
14”
Built for high volume use
Includes add-on faucet with 12” spout
8” center wall mount
Wall bracket included
Built-in internal check valves
17-109W
FULL LINE OF
REPLACEMENT
PARTS AVAILABLE!
FULL LINE OF
REPLACEMENT PARTS
AVAILABLE!
Wall Mount
Pre-Rinse
Royal Series
Wall Mount Faucet
•
•
•
•
• Built for high volume use
• 8” center wall mount
• Built-in internal check valves
14-808
14-810
14-812
14-814
8”
10”
12”
14”
Equipment
Pre-Rinse/Faucets
Built for high volume use
8” center wall mount
Wall bracket included
Built-in internal check valves
17-108W
FULL LINE OF
REPLACEMENT
PARTS AVAILABLE!
Service Sink
Faucet
•
•
•
•
Built for high volume use
8” centers with 61⁄2” spout
Wall bracket included
Built-in vacuum breaker
Add-On
Faucet
16-127
• Interchangeable
with all brands
• 12” spout
FULL LINE OF
REPLACEMENT
21-139
PARTS AVAILABLE!
FULL LINE OF
REPLACEMENT
PARTS AVAILABLE!
Replacement
Spray Head
• Interchangeable to all brands
• Complies with EPA act 2005
• Chrome plated brass
21-129
Replacement Hose
• Interchangeable with all brands
• 44” length
Deck Mount
Pre-Rinse
• Built for high volume use
• Single hole deck mount
for 11⁄4” opening
• Wall bracket included
• Built-in internal check valves
21-133
17-202W
262_272NAFEDcat.indd 263
FULL LINE OF
REPLACEMENT
PARTS AVAILABLE!
263
9/26/07 4:40:19 PM
Equipment
Sinks & Work Tables
Work Tables
WT24X72-BG
WT24X84-BG
WT24X96-BG
WT24X108-BG
WT24X120-BG
WT30X30-BG
WT30X36-BG
WT30X48-BG
WT30X60-BG
WT30X72-BG
WT30X84-BG
WT30X96-BG
WT30X108-BG
WT30X120-BG
•
•
•
•
16 gauge 304 stainless steel top
4˝ backsplash
Working height 36˝ tall
BG models have adjustable 11⁄4˝ galvanized
cross bracing and legs with plastic feet
• BS models have adjustable 11⁄4˝ S/S cross
bracing and legs with S/S feet
• Shipped knocked down
WT24X30-BG
WT24X36-BG
WT24X48-BG
WT24X60-BG
WT24X30-BS
WT24X36-BS
WT24X48-BS
WT24X60-BS
24˝
24˝
24˝
24˝
x
x
x
x
30˝
36˝
48˝
60˝
Soiled Dish Tables
•
•
•
•
•
•
•
16 gauge 304 stainless steel top and tub
201⁄4˝ x 201⁄4˝ x 6˝ deep tub size
15⁄8˝ galvanized legs with adjustable plastic feet
Basket strainer included - faucet is extra
Welded pre-rinse tub
10˝ backsplash with 2˝ return
Specify backsplash or deck mount faucet holes
DDT-36-L
30˝ x 36˝
DDT-36-R
30˝ x 36˝
DDT-48-L
30˝ x 48˝
DDT-48-R
30˝ x 48˝
DDT-60-L
30˝ x 60˝
DDT-60-R
30˝ x 60˝
DDT-72-L
30˝ x 72˝
DDT-72-R
30˝ x 72˝
“L” or “R” indicates tub position
3 Compartment Sinks
•
•
•
•
•
16 gauge 304 stainless steel top and tubs
10˝ backsplash with 2˝ return
Three 12˝ deep welded tubs with 2˝ divider
15⁄8˝ galvanized legs with adjustable 1˝ plastic feet
Basket strainers included, faucets not included
264
262_272NAFEDcat.indd 264
24˝
24˝
24˝
24˝
24˝
30˝
30˝
30˝
30˝
30˝
30˝
30˝
30˝
30˝
WT24X72-BS
WT24X84-BS
WT24X96-BS
WT24X108-BS
WT24X120-BS
WT30X30-BS
WT30X36-BS
WT30X48-BS
WT30X60-BS
WT30X72-BS
WT30X84-BS
WT30X96-BS
WT30X108-BS
WT30X120-BS
x
x
x
x
x
x
x
x
x
x
x
x
x
x
72˝
84˝
96˝
108˝
120˝
30˝
36˝
48˝
60˝
72˝
84˝
96˝
108˝
120˝
Clean Dish Tables
•
•
•
•
30˝
30˝
30˝
30˝
30˝
30˝
30˝
CDT-24-L
CDT-24-R
CDT-36-L
CDT-36-R
CDT-48-L
CDT-48-R
CDT-60-L
x
x
x
x
x
x
x
24˝
24˝
36˝
36˝
48˝
48˝
60˝
16 gauge 304 stainless steel top
15⁄8˝ galvanized legs
1˝ adjustable plastic feet
10˝ backsplash with 2˝ return
CDT-60-R
CDT-72-L
CDT-72-R
CDT-84-L
CDT-84-R
CDT-96-L
CDT-96-R
30˝
30˝
30˝
30˝
30˝
30˝
30˝
x
x
x
x
x
x
x
60˝
72˝
72˝
84˝
84˝
96˝
96˝
E Series
Wall Shelves
• 18 gauge construction
• 2 wall brackets included
(84˝ and 96˝ include 3 brackets)
EWMS-12-24
EWMS-12-36
EWMS-12-48
EWMS-12-60
EWMS-12-72
EWMS-12-84
12˝
12˝
12˝
12˝
12˝
12˝
x
x
x
x
x
x
24˝
36˝
48˝
60˝
72˝
84˝
3C17X17-0
3C17X23-0
3C23X23-0
3C17X17-L-18
3C17X17-R-18
3C17X23-L-18
3C17X23-R-18
3C17X23-L-24
3C17X23-R-24
3C23X23-L-24
3C23X23-R-24
3C17X17-2-18
3C17X17-2-24
3C17X23-2-18
3C17X23-2-24
3C23X23-2-24
3C20X28-2-20
3C20X28-2-24
EWMS-12-96
EWMS-14-24
EWMS-14-36
EWMS-14-48
EWMS-14-60
EWMS-14-72
EWMS-14-84
EWMS-14-96
TUB SIZE
17˝ x 17˝
17˝ x 23˝
23˝ x 23˝
17˝ x 17˝
17˝ x 17˝
17˝ x 23˝
17˝ x 23˝
17˝ x 23˝
17˝ x 23˝
23˝ x 23˝
23˝ x 23˝
17˝ x 17˝
17˝ x 17˝
17˝ x 23˝
17˝ x 23˝
23˝ x 23˝
20˝ x 28˝
20˝ x 28˝
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
12˝
14˝
14˝
14˝
14˝
14˝
14˝
14˝
SIZE
221⁄2˝
281⁄2˝
281⁄2˝
221⁄2˝
221⁄2˝
281⁄2˝
281⁄2˝
281⁄2˝
281⁄2˝
281⁄2˝
281⁄2˝
221⁄2˝
221⁄2˝
281⁄2˝
281⁄2˝
281⁄2˝
231⁄2˝
331⁄2˝
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
96˝
24˝
36˝
48˝
60˝
72˝
84˝
96˝
60˝
60˝
78˝
751⁄2˝
751⁄2˝
751⁄2˝
751⁄2˝
811⁄2˝
811⁄2˝
991⁄2˝
991⁄2˝
91˝
103˝
91˝
103˝
121˝
104˝
112˝
264
9/26/07 4:40:25 PM
Undercounter Dishwasher
•
•
•
•
Top mounted controls
All stainless steel construction
Built-in booster heater and pumped drain
141⁄2” height clearance accommodates
larger dishes and half size sheet pans
• Low water consumption
• 30 racks/120 covers per hour
• 24” w. x 25” d. x 331⁄4” h.
MODEL CMA-180UC
High Temperature Door-Type Dishwasher
•
•
•
•
•
•
Uses only .96 gallons of water per cycle • Auto fill
60 Racks/240 covers per hour
High temperature sanitizing with built-in booster heater
All stainless steel construction
External Poly Pro™ scrap accumulator
Upper and lower stainless steel wash arms with reinforced end
caps - easily removed for cleaning
• 251⁄2” w. x 25” d. x 60” h.
SPECIFY CORNER OR STRAIGHT MODEL
Equipment
Dishwashing Machines
MODEL CMA-180B
High Temperature Conveyor Dishwasher
• Uses only .94 gallons of water per cycle • Auto fill
• 205 Racks/820 covers per hour
• High temperature sanitizing with built-in booster heater
• All stainless steel construction
• Unique 3-stage washing process provides pre-wash, power wash and final rinse
• External Poly Pro™ scrap accumulator
• Built-in chemical resistant industrial 10kW heater
• Large 19” high opening accommodates larger items and utensils
• Three speed settings available for optimum cleaning performance
• 44” w. x 251⁄8” d. x 551⁄2” h.
SPECIFY DIRECTION OF TRAVEL; LEFT TO RIGHT, RIGHT TO LEFT.
MODEL CMA-44H
Chemical Sanitizing Conveyor Dishwasher
•
•
•
•
•
Economical – uses only .8 gallons of water per cycle • Auto fill
242 Racks/968 covers per hour
Low temperature chemical sanitizing
All stainless steel construction
Four-stage washing process provides pre-wash,
dual power wash and final rinse
• External Poly Pro™ scrap accumulator
• Built-in chemical resistant industrial 10kW heater
• Large 19” high opening accommodates larger items and utensils
• Three speed settings available for optimum cleaning performance
• 66” w. x 251⁄8” d. x 551⁄2” h.
SPECIFY DIRECTION OF TRAVEL; LEFT TO RIGHT, RIGHT TO LEFT.
MODEL CMA-66L
265
262_272NAFEDcat.indd 265
9/26/07 4:40:30 PM
Equipment
Dishwashing Machines
E-series Rack Conveyor Dishwasher
The Champion 44DR offers lowest water consumption without sacrificing clean
results. The advantage....Dual Rinse technology ensures all wares are fully
rinsed with more than 300+ gallons of water per hour with actual fresh water
consumption of no more than 112 gallons per hour.
ADDITIONAL BENEFITS:
• ENERGY STAR® rated
• The Dual Rinse technology has reduced water consumption by more than 65%
which converts into considerable money and energy savings
• Optional nested electric booster which transfers heat back into the wash tank
for additional savings
• One-piece wash manifold designed to strip soils from wares
• Standard vertical clearance accepts 18˝ x 26˝ sheet pans
• Multiple-tank models, loading and unloading options, and many other
accessories available
MODEL 44DR
TO HELP DETERMINE WHAT SIZE DISHWASHING MACHINE YOU WILL
NEED, YOU MUST FIRST DETERMINE HOW MANY RACKS OF DISHES
PER HOUR YOU WILL GENERATE. HERE’S AN EQUATION THAT MAY
HELP: (# OF PIECES PER PERSON) X (# OF PERSONS PER HOUR)
÷ 20 PIECES PER RACK = RACKS PER HOUR REQUIRED.
High Temperature Door-Type Dishwasher
All stainless steel construction, easy access, and top mounted controls make the DH-1000
the perfect choice in dishwashers when limited space is a concern. Equipped with a
stainless steel built-in electric booster in 40°F. rise or optional 70°F. rise provides 180°F. final
rinse water for sanitizing.
• ENERGY STAR® rated
• Straight-through or corner application – simple conversion in a matter of minutes
• Parts commonality with other machines
• Superior rinse results – machine fills exclusively through the pump, helping
thoroughly flush out wash water from the spray system during drain cycle.
This feature ensures soap-free rinse water for superior results
• Direct replacement – the DH-1000 is a direct replacement to
most competitor’s models without table modification
• Machine fully assembled, ready to install
• 1 hp. pump motor
• Door safety switch
• Interchangeable upper and lower spray arms
• Aircap design feature eliminates vacuum breaker
• Optional detergent and rinse pump available
MODEL DH-1000
High Temperature Undercounter Dishwasher
266
The new E-series undercounter offers enhanced performance capacity, increased efficiency
with reduced water consumption. The electro-mechanical control package ensures reliable
trouble-free operation and low service cost.
ADDITIONAL BENEFITS:
• ENERGY STAR® rated
• 30 racks per hour • 0.9 gallons fresh water consumption per cycle
• Soft-start pump – for delicate wares
• Rinse sentry – extends the cycle time to ensure 180˚F. final rinse
• Built-in booster options – 40˚F. rise (6kW) standard or 70˚F. rise (9kW) optional
• Extended wash/delime switch for heavy soils
• Upper and lower stainless steel wash/rinse spray arms
• Stainless steel top and sides are standard
• Detergent and rinse pumps are standard
• Double wall construction for whisper quiet operation
• Pumped drain
MODEL UH170B
262_272NAFEDcat.indd 266
266
9/26/07 4:40:35 PM
Avenger™ HT
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Built-in booster heater, detergent and rinse pump
Automatic fill, push button start, two minute automatic cycle
1.1 gallons of water per rack, 26.4 gallons of water per hour
Labyrinth type door design
Automatic pumped drain for floor
and wall drain installations
Pre-installed water pressure regulator
304 stainless steel construction
Stainless steel wash pump
Electro mechanical components
Manual override for extended wash and deliming
Simplified controls allow easy access for operation
and service
Door safety switch
Pumped drain
One (1) each peg and combination rack included
Above water scrap tray
3
⁄4 hp wash motor pump
Unique timer allows customized cycle times
Fresh water rinse eliminates wash water contamination
CAUTION! IF YOU ARE USING A
LOW TEMP OR CHLORINE BATH
TYPE DISHWASHING SYSTEM,
TAKE GREAT CARE IN FOLLOWING
THE MANUFACTURER’S
INSTRUCTIONS. AN OVERCONCENTRATION OF SODIUM
HYPOCHLORITE (BLEACH), THE
ACTIVE SANITIZING AGENT OF
THESE SYSTEMS, WILL ATTACK
MOST METAL TABLEWARE.
IMPROPER USE OR FAULTY
EQUIPMENT FUNCTIONING WILL
CAUSE STAINING OR CORROSION
OF EVEN THE FINEST STAINLESS
STEEL. IT IS VERY IMPORTANT
THAT YOU USE ONLY A PLASTIC
OR STAINLESS STEEL PAN FOR
PRESOAKING.
Equipment
Dishwashing Machines
TempStar™
DOOR-TYPE DISHWASHER
• Total automatic cycle – 58 seconds
• Low water usage – 1 gallon per rack
• Built-in booster heater sized to raise incoming
140˚F water to 180˚F for sanitizing rinse
• Built-in pressure regulator and gauge
• Specially designed stainless steel nozzles provide superior cleaning action
• 171⁄4˝ door opening accepts 18˝ trays
• Field convertible straight through to corner
• Heavy duty stainless steel construction
• Auto-fill and auto-start
• Safety door switch
• Delime/manual wash switch
• Hi-limit thermostat and low water protection
• Top mounted controls for ease of installation
• Uses standard 20˝ x 20˝ racks
• Detergent/rinse additive signal connection fuse block
• No external booster heater is required
• Also available with 70˚ rise option (No extra cost)
Traditional Series
Conveyor Dishwasher
•
•
•
•
•
•
•
•
•
•
•
•
•
•
252 racks per hour hi-temp sanitizing rinse
0.74 gallons per rack hi-temp sanitizing rinse
Incoming water pressure regulator
Standard 18” clearance
Complete Right-to-Left and Left-to-Right convertibility in the field
Totally electro-mechanical; no solid state controls utilized
Fully automatic including auto-fill
Completely self-draining stainless steel wash pump
Exclusive “Energy Guard” controls system operates wash and
rinse sections only when a rack is being washed or rinsed
A long 16” wash section as well as 18” separation
between wash and rinse produces superior results
Convenient, externally operated lever drain
Stainless steel frame, legs, adjustable bullet feet,
and front appearance panel are all standard
Standard 8” vent cowls/splash shields on both
wash and rinse ends of the machine
208/230V, 60Hz, 1 or 3 Phase
MODEL TS-44
262_272NAFEDcat.indd 267
267
9/26/07 4:40:39 PM
Equipment
Warewashing
OptiClean™ Warewashing System
OptiClean’s open profile facilitates superior washing, complete rinsing and fast drying. Racks drain quickly to
reduce spotting/drying time – no flat surfaces to trap water or loose food particles inside the rack. Double wall
construction provides maximum strength. Comfort curved handles are molded into all four sides for easy handling,
won’t pinch fingers. Unique “honeycomb” design distributes load more effectively. Sturdy bottom with four-way
tracking for easy dish machine loading – eliminates the need to rotate racks. Positive stacking from either direction
– stacks with all major competitors. All racks are NSF listed. Color: Carlisle Blue.
OPTICLEAN™ OPEN/BOWL RACKS
• Sturdy open bottom rack
• Ideal for all large dishes, containers, brushes, utensils and cutlery
• Use for all types of bowls
RB
Bowl Rack
RE*
Open Extender
* NOTE: “RE OPEN EXTENDER” CAN BE USED WITH ANY OPTICLEAN™ GLASS OR DISH RACK
RB
RF
RW20
OPTICLEAN™ FLATWARE RACKS
• Bottom grid allows for free flow of water and air
• Keeps flatware in place for thorough washing and drying
• Perfect for utensils, ramekins, and other small items
RF
Combination/Flatware Rack
OPTICLEAN™ NEWAVE™ GLASS RACKS
• Holds 20% more than comparable square compartmented glass racks
• Reduces storage space, labor, inventory and chemical usage by up to 20%
• Rounded design holds glasses more securely in place
• Designed to fit the most popular sizes of glasses and tumblers
20-COMPARTMENT
30-COMPARTMENT
RW20 With Integrated Extender
RW30
With Integrated Extender
RW20-1 With 2 Extenders
RW30-1 With 2 Extenders
RW20-2 With 3 Extenders
RW30-2 With 3 Extenders
RW20-3 With 4 Extenders
RW30-3 With 4 Extenders
OPTICLEAN™ 16-COMPARTMENT GLASS RACKS
• Perfect for large cocktail glasses and delicate wine stems w/oversize bowls
• Compartment size: 41⁄2˝ x 41⁄2˝, accommodates glasses up to 43⁄8˝ in dia.
RG16-1 With 1 Extender
RG16-2 With 2 Extenders
RG16-3 With 3 Extenders
RG16-4 With 4 Extenders
RE16
16-Compartment divided extender
OPTICLEAN™ 25-COMPARTMENT GLASS RACKS
• Use for large diameter beverage glasses and most red wine stems and goblets
• Compartment size: 31⁄2˝ x 31⁄2˝, accommodates glasses up to 33⁄8˝ in dia.
RG25-1 With 1 Extender
RG25-2 With 2 Extenders
RG25-3 With 3 Extenders
RG25-4 With 4 Extenders
RE25
25-Compartment divided extender
RG25-1
OPTICLEAN™ 36-COMPARTMENT GLASS RACKS
• Use with tumblers, white wine glasses and other narrow bowl stems
• Compartment size: 215⁄16˝ x 215⁄16˝, accommodates glasses up to 27⁄8˝ in dia.
RG36-1 With 1 Extender
RG36-2 With 2 Extenders
RG36-3 With 3 Extenders
RG36-4 With 4 Extenders
RE36
25-Compartment divided extender
E-Z Glide™ Rack Dollies
• Dollies trap water from wet racks; convenient drain
feature makes emptying water easy
• Large 4˝ ball bearing swivel casters with rubber wheels
• Colors available: Blue or Black
C2235R
268
262_272NAFEDcat.indd 268
C2235R
C2235HR
Glass Rack Dolly w/o handle
Glass Rack Dolly w/handle
268
9/26/07 4:40:43 PM
Full-Size Compartment Racks
•
•
•
•
Individual compartments help prevent chipping and breakage
Wide range of sizes, capacities, and interchangeable dividers and risers
Ideal for storage and machine washing, provide excellent protection and minimize costly replacement
Open design promotes thorough washing action, complete rinsing,
rapid drying and quick glass cooling for spot-free glassware
• Outside dimensions: 193⁄4˝ x 193⁄4˝ (50 x 50 cm)
• Rack Colors: Light Green, Cocoa, Red, Light Blue, Gold, Gray, Royal Blue, Burgundy
9-COMPARTMENT
• Maximum inside compartment size 57⁄8˝ (14.9 cm) square
• Diagonal Dimensions: 85⁄16˝ (21.1 cm)
16-COMPARTMENT
• Maximum inside compartment size 43⁄8˝ (11.1 cm) square
• Diagonal Dimensions: 63⁄16˝ (15.7 cm)
25-COMPARTMENT
• Maximum inside compartment size 31⁄2˝ (8.9 cm) square
• Diagonal Dimensions: 415⁄16˝ (12.5 cm)
36-COMPARTMENT
• Maximum inside compartment size 27⁄8˝ (7.3 cm) square
• Diagonal Dimensions: 41⁄16˝ (10.3 cm)
52715
49-COMPARTMENT
• Maximum inside compartment size 27⁄16˝ (6.2 cm) square
• Diagonal Dimensions: 37⁄16˝ (8.7 cm)
52720
Equipment
Warewashing
52712
9 COMP
52726
52727
52728
52730
52729
52731
16 COMP
52694
52718
52719
52720
52721
52732
25 COMP
52684
52710
52711
52712
52713
52733
36 COMP
52689
52714
52715
52716
52717
52734
49 COMP
52699
52722
52723
52724
52725
52735
Short – 41⁄8˝ Overall Height, 213⁄16˝ Inside Height
Medium – 55⁄8˝ Overall Height, 45⁄16˝ Inside Height
Tall – 7˝ Overall Height, 511⁄16˝ Inside Height
X Tall – 81⁄2˝ Overall Height, 71⁄8˝ Inside Height
XX Tall – 97⁄8˝ Overall Height, 81⁄2˝ Inside Height
XXX Tall – 115⁄16˝ Overall Height, 915⁄16˝ Inside Height
Full-Size Cup Racks
THE PROPER SIZE GLASS RACK
IS ESSENTIAL TO AVOID COSTLY
BREAKAGE DURING WASHING
AND STORAGE. OUR SALES
STAFF CAN HELP YOU SELECT
THE PROPER RACKS TO FIT YOUR
GLASSWARE. ASK US!
• Holds most standard-sized cups
• Extra-high, molded compartments prevent chipping
and breakage
• Molded tilting device prevents water from pooling in
bottom of cup
• Outside dimensions: 193⁄4˝ x 193⁄4˝ (50 x 50 cm)
16 COMP
20 COMP
52674
52675
Short – 41⁄8˝ Overall Height, 23⁄4˝ Inside Height
52676
52677
Medium – 59⁄16˝ Overall Height, 41⁄8˝ Inside Height
Full-Size Plate & Tray Rack
Full-Size Open Racks
• Holds plates and trays upright for the ideal cleaning angle
• Plate lock to keep plates from touching, reducing
chipping and breakage
• Extended height rack has taller pegs and
sidewalls to accommodate larger plates
• Outside dimensions: 193⁄4˝ x 193⁄4˝
(50 x 50 cm)
• Distance between pegs:
19⁄16˝ x 19⁄16˝ (4 x 4 cm)
• Designed for uniquely shaped
or oversized dishes, utensils
and cookware
• Outside dimensions:
193⁄4˝ x 193⁄4˝
(50 x 50 cm)
52672
31⁄4˝ Overall Height, 23⁄4˝ Inside Height
Full-Size Open End Racks
• Ideal for washing trays
• Item 52678 has a stainless
steel-reinforced channel to support fiberglass
and laminated trays or metal items
• Item 52673 designed only
for fast food trays
• Outside dimensions:
193⁄4˝ x 193⁄4˝ (50 x 50 cm)
52673
52678
33⁄4˝ Overall Height, 23⁄4˝ Inside Height
33⁄4˝ Overall Height, 23⁄4˝ Inside Height
262_272NAFEDcat.indd 269
52670
52680
52681
52682
52683
Short – 41⁄8˝ Overall Height, 213⁄16˝ Inside Height
Medium – 51⁄2˝ Overall Height, 41⁄8˝ Inside Height
Tall – 67⁄8˝ Overall Height, 51⁄2˝ Inside Height
X Tall – 83⁄16˝ Overall Height, 613⁄16˝ Inside Height
XX Tall – 99⁄16˝ Overall Height, 81⁄4˝ Inside Height
Full-Size Flatware Rack
• Tight lattice bottom grid prevents
flatware from falling through
• Outside dimensions:
193⁄4˝ x 193⁄4˝
(50 x 50 cm)
52671
41⁄8˝ Overall Height, 25⁄8˝ Inside Height
269
9/26/07 4:40:47 PM
Equipment
Waste Disposers
High-Efficiency Waste Disposing Systems For Every Application...
Salvajor
S914
Scrapmaster
Salvajor
Collectors
• The Salvajor Scrapmaster is
a pre-rinsing and disposing
system designed to increase
the speed and efficiency of
scrapping and pre-rinsing
for small to medium sized
conveyor dish machines
• Not only will it double
(if not triple) overall
efficiency, the Scrapmaster
saves thousands of
dollars per year in wasted
water and sewer costs
by using recirculated
water for pre-rinsing
Salvajor
TroughVeyor
• The Salvajor S914
and S419 Collectors
are designed for use
in areas prohibiting
food waste disposers
• The S914 is designed
for non-trough
applications, the S419
is for use with troughs
• Collectors are
unique in output and
simplicity: Instead of
collecting every scrap
of garbage, collectors
wash soluble foods
harmlessly through the
sewers, reducing bulk
waste by as much as
50%. Only fibrous
and non-soluble
food is left behind
for the land fills
• The Collector water
system recirculates
water at the rate of
30 gallons per minute
while only consuming
2 gallons, saving
thousands of dollars
in wasted water
S419
• The Salvajor TroughVeyor
is a food waste conveying
and disposing system which
uses recirculated water
to propel food down the
trough with the power of 70
gallons of water per minute
• The TroughVeyor is designed
for use with large conveyor
and flight dish machines
and is used in place of
fresh water troughs which
require excessive amounts
of water in order to float
food waste to the disposer
Salvajor Disposer
• Water-cooled motor runs cooler
than ordinary types for maximum
efficiency and longer life
• Heavy duty, corrosion-resistant
aluminum housing retains sanitary,
handsome chrome-like finish
• Water controls save thousands of
dollars on water and sewer costs
• Larger mixing chamber ensures a
better water-to-waste ratio, allowing
water consumption control and
smooth sewer flow
• Water-tight controls ensure safety in
wet dishroom climate
• Safety is assured for product liability
• Short top housing permits installation
of any unit (1-10 Hp), under a 14˝
deep sink
D
C
B
E
F
G
A
2˝ or 3˝ DRAIN
D
E
B
F
C
G
H
A
2˝ or 3˝
DRAIN
270
262_272NAFEDcat.indd 270
Salvajor SA Sink
Assembly
EQUIPMENT FURNISHED FOR
SINK MOUNT APPLICATION:
A. Disposer
B. Sink mount, 31⁄2˝ or 61⁄2˝
C. Fixed nozzle, 1⁄2˝
D. Vacuum breaker
E. Solenoid valve, 1⁄2˝
F. Flow control
Salvajor CA Cone
Assembly
EQUIPMENT FURNISHED
FOR CONE-STYLE
APPLICATION:
A. Disposer
B. 12˝, 15˝, or 18˝ cone
C. Fixed nozzle, 1⁄2˝
D. Vacuum breaker
E. Solenoid valve, 1⁄2˝
F. Scrap ring
G. Flow control
270
9/26/07 4:40:52 PM
COMPLETE SYSTEM SHOWN
Waste Xpress®
Food Waste
Reduction Systems
REDUCE WASTE VOLUME BY 85%.
• Waste Xpress systems are designed
to work without cardboard
• They efficiently reduce food waste,
paper, plastic and similar materials
• There’s less waste to haul and
minimal water consumption
• Quick and easy to clean, no tools
are required
• Fits under a standard table minimum height 34˝
Food Waste Disposers
• Built to perform, day in and day out and the
overwhelming choice of commercial users
• From our light-duty LC-50 to our big-capacity
workhorse 10 hp. models, we have disposers
for any size food service operation
LC-50
SS-50
SS-75
SS-100
SS-125
SS-150
SS-200
SS-300
SS-500
SS-750
SS-1000
SS-500
Light Duty
1
⁄2 hp.
3
⁄4 hp.
1 hp.
11⁄4 hp.
11⁄2 hp.
2 hp.
3 hp.
5 hp.
71⁄2 hp.
10 hp.
Aqua-Saver®
Systems For
Disposers
Wide selection, superior quality and the industry’s most complete
service network make InSinkErator®
the choice of food service professionals.
Add-on device to
existing disposer system
Control panel
(includes Aqua-Saver device)
AS-101
Hot Water
Systems
Point-Of-Use Undersink
Water Heaters
• Three ways to save
time, energy and water
• All systems install without
expensive connections
to a central source
• Dispense 190˚ hot water
instantly, so there’s
no waste
SPECIFICALLY FOR NEW OR RETROFIT INSTALLATIONS.
• These heaters are available in 21⁄2 and 4 gallon sizes
and can go almost anywhere, under a sink
or under a cabinet
• Each has a 1500 watt heating element to quickly
bring water to any thermostat setting between
110˚ and 170˚ F.
• Tanks are corrosion-resistant brass, wrapped in
polystyrene and steel-jacketed for maximum heat
retention and energy savings
H-778
UW/UWL
262_272NAFEDcat.indd 271
21⁄2 gallon tank
4 gal. tank
AS-101
• Cut disposer water
usage by 70% or more
• When the disposer is
grinding, Aqua-Saver
lets just enough water
flow to flush away waste
• When disposer is idle,
water flow is minimum
• Users report saving
thousands of gallons
per day
AS
152
154
Equipment
Waste Disposers & Water Systems
CI300
154
Provides 190˚ water for cooking
& hot drinks, 2⁄3 gal. tank
Delivers warm water instantly for
clean-up
Provides 190˚ water in a sleek,
modern look
271
9/26/07 4:40:58 PM
Equipment
Water Heaters
Booster Water Heaters
• Provides 180° F. sanitizing rinse water for dishwashers
• Dishes and flatware air-dry instantly to
save time, space and money
• Available in models from 4 kW to 57 kW and
storage capacity of 6 gallons (23 liters)
• Castone® lined tank is standard and features
a 10 year limited warranty
• 208V, 240V, and 480V
C-12
Mini-Compact Booster Water Heaters
MC-10
• Features a stainless steel tank and fast recovery, making it ideal for
hot water sanitizing or point-of-use hot water dispensing
• Available in 10 kW and 11 kW, the unit is small enough to be
installed almost anywhere on 6˝ legs, with brackets or surface
mounted
• 208V and 240V
A HATCO BOOSTER HEATER, WHEN COMBINED WITH A GOOD
COMMERCIAL DISHWASHING MACHINE, PROVIDES HOT WATER
FOR A SANITIZING RINSE, RAPID SELF-DRYING, AND SPARKLING
CLEAN GLASSES AND TABLEWARE.
• HATCO BOOSTER HEATERS BRING HOT WATER FROM LINE
TEMPERATURE UP TO 180° F.
• EVERY HATCO BOOSTER HEATER HAS AN “ENERGY CUT-OFF SWITCH” (ECO)
TO PREVENT THE WATER TEMPERATURE FROM EXCEEDING PRE-SET LIMITS
3CS Sanitizing Sink Heaters
• Maintains 180°F. rinse water for manual warewashing
operations without taking up valuable sink space
• Designed to fit under the sink, the 3CS is ideal for 3 or 4
compartment sinks, pot and pan sinks and bar sinks
• Shipped ready to install with gaskets and fittings
• 208V, 240V and 480V
3CS-6 SHOWN WITH OPTIONAL
TEMPERATURE MONITOR
IF YOU ARE THINKING OF SWITCHING FROM A LOW-TEMP WAREWASHING SYSTEM TO A HIGH-TEMP SYSTEM, A BOOSTER WATER HEATER
IS THE MOST EFFICIENT WAY TO HEAT WATER TO THE REQUIRED 180°F. MINIMUM RINSE TEMPERATURE. NOT ONLY WILL YOU REALIZE
A SAVINGS ON SANITIZING CHEMICALS, BUT YOU’LL USE LESS WATER, TOO!
272
262_272NAFEDcat.indd 272
272
9/26/07 4:41:02 PM