Vizion UF-216 series Specifications

Manufacturing
Numbers:
9700435
Water filtration
system
P/N 1011078 Rev. B 03/12
UF-216 Series
Owner ’s Manual
UF-216 water Filtration system
A.J. Antunes & Co.
Table of contents
Owner Information......................................................2
General.......................................................................2
Warranty Information..................................................2
Service/Technical Assistance.....................................3
Important Safety Information.....................................4
Specifications..............................................................5
Dimensions.................................................................5
Replacement Cartridges.............................................5
Ultra Filter Cartridge Capacities.................................5
Electrical Ratings........................................................5
Electrical Cord & Plug Configurations........................5
Overview......................................................................7
Overview.....................................................................7
Manual Flushing.........................................................7
Installation....................................................................8
Unpacking...................................................................8
Equipment Setup........................................................8
Mounting the System..................................................9
Inlet Water Plumbing..................................................9
Permeate Line Plumbing..........................................10
Drain Valve Connection............................................10
Starting the Controller..............................................10
Rinsing the Ultra Filter Cartridge..............................11
Sanitizing the System and Lines..............................11
Maintenance...............................................................12
Replacing the Ultra Filter Cartridge..........................12
System Sanitization..................................................12
Changing the Interval Setting...................................13
Resetting the Timer Program...................................13
Troubleshooting........................................................14
Replacement Parts ...................................................15
Limited Warranty.......................................Back Cover
Owner Information
General
Warranty Information
VIZION, a division of A.J. Antunes & Co., has partnered
with companies from around the globe to produce the
UF-216 Series water filtration system. The UF-216
Series reduces cysts and turbidity that can enter a
typical water supply. This patented technology is now
available to you, sized for your particular application.
All filter configurations utilize NeoH capillary membranes, providing the latest innovation in reusable surface filtration technology.
Please read the full text of the Limited Warranty in this
manual.
This manual provides the safety, installation and
operating procedures for the UF-216 Series water
filtration system. We recommend that all information
contained in this manual be read prior to installing and
operating the unit.
• Damages caused in shipment or damage as
result of improper use.
• Installation of electrical service.
• Normal maintenance as outlined in this manual.
• Malfunction resulting from improper maintenance.
• Damage from moisture leaking into electrical
components.
• Normal maintenance as outlined in this manual.
• Damage from tampering with, removal of, or
changing any preset control or safety device.
If the unit arrives damaged, contact the carrier immediately and file a damage claim with them. Save all
packing materials when filing a claim. Freight damage
claims are the responsibility of the purchaser and are
not covered under warranty.
The warranty does NOT extend to:
Your UF-216 Series unit is manufactured from the finest
materials available and is assembled to VIZION’s strict
quality standards. This unit has been tested at the factory
to ensure dependable trouble-free operation.
Important! Keep these instructions for future reference. If the unit changes
ownership, be sure this manual accompanies the equipment.
2
P/N 1011078 Rev. B 03/12
UF-216 water filtration system
A.J. Antunes & Co.
Owner information (continued)
Service/Technical Assistance
Suggested replacement period for Ultra Filter Cartridge
is approximately 3 years.
If you experience any problems with the installation or
operation of your unit, contact us at 1-630-784-1000, or
toll free in the United States at 1-800-253-2991.
For sales in the state of Iowa:
Fill in the information in the next column and have it
handy when calling for assistance. The serial number
is on the specification plate located on the unit.
Seller: Date:
Buyer: Date:
Purchased From:
Date of Purchase:
Model No.:
Serial No.:
Mfg. No.:
Important
A.J. Antunes and Co. reserves the right to change specifications and product design without
notice. Such revisions do NOT entitle the buyer to corresponding changes, improvements,
additions or replacements for previously purchased equipment.
P/N 1011078 Rev. B 03/12
3
UF-216 water Filtration system
A.J. Antunes & Co.
Important Safety Information
In addition to the warnings and cautions in this manual,
use the following guidelines for safe operation of the unit:
• Read all instructions before using equipment.
• Install or locate the equipment only for its intended
use as described in this manual. Do NOT use
corrosive chemicals in this equipment.
• Do NOT operate this equipment if it has a damaged
cord or plug; if it is not working properly, or if it has
been damaged or dropped.
• This equipment should be serviced by qualfied personnel only. Contact A.J. Antunes & Co. for repair.
• Do NOT immerse cord or plug in water.
• Keep cord away from heated surfaces.
The following warnings and cautions appear throughout
this manual and should be carefully observed:
• Unplug the power cord before performing any
service or maintenance on the unit.
• All electrical connections must be in accordance
with local electrical codes and any other applicable
codes.
• Warning electrical shock hazard. Failure to follow these instructions
could result in serious injury or death.
• If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a similarly qualified person.
• This equipment is to be installed to comply with the
local plumbing code and any other applicable code.
• Water pressure must not exceed 100 psig (690
kPa). To reduce water pressure, install a water
pressure regulator and set water pressure to suit
application.
• The trans membrane pressure (inlet water pressure minus the permeate water pressure) must not
exceed 45 psi (310 kPa).
• System should be supplied only with cold water.
• Commonwealth of Massachusetts Plumbing Code
248 CMR shall be adhered to. The use of saddle
valves are not permitted, please consult your local
plumber.
• A ground fault circuit interrupter (GFCI) must be
installed on the circuit to this system
• When installed on metallic plumbing, a properly
sized electrical bonding jumper must be installed
across the inlet and outlet pipes serving this device.
- Do NOT modify the power supply cord plug. If
it does not fit the outlet, have a proper outlet
installed by a qualified electrician.
- Do NOT use an extension cord with this unit.
4
P/N 1011078 Rev. B 03/12
UF-216 water filtration system
A.J. Antunes & Co.
Specifications
Dimensions
Electrical Ratings
A
Model &
Mfg. No.
Voltage Watts
UF-216
9700435
100‒240
10
Amps
Hertz
0.8
50/60
Electrical Cord & Plug Configurations
B
Kit Model
Number
Description
0012146
DC Power Supply
100 - 240 VAC
Includes the
4 plug adaptors
below
NOTE: PLUG STYLE
MAY VARY
US
NEMA 1-15 (2 pin)
or NEMA 5-15
(3 Pin)
C
Euro
CEE 7/16
Model &
Mfg. No.
Width
(A)
Depth
(B)
Height
(C)
Operating
Weight
UF-216
9700435
11”
(28 cm)
4”
(10 cm)
26”
(66 cm)
12 lbs.
(5.5 kg)
AS/NZS
3112
AUS
(2 Pin)
UK
BS 1363
Replacement Cartridges
Replacement Cartridge
UF-216
Configuration
Ultra Filter Cartridge
Part No.
EURO
CEE 7/16
AS/NZS 3112
AUS
(2 PIN)
UK
BS 1363
Caution
All electrical connections must be in accordance
with local electrical codes and any other
applicable codes.
7000466
Ultra Filter Cartridge Capacities
A ground fault circuit interrupter (GFCI) must be
installed on the circuit to this system.
Max.Operating Pressure
100 psig (690 kPa)
Max. Operating Temp. 104°F (40°C)
Min. Operating Temp. 40°F (4°C)
Max. Trans Membrane Pressure 45 psi (3.1 bar)
pH Range3-10
MWCO 100 kD
P/N 1011078 Rev. B 03/12
US
NEMA 1-15 (2 PIN)
or NEMA 5-15
(3 PIN)
When installed on metallic plumbing, a properly
sized electrical bonding jumper must be installed
across the inlet and outlet pipes serving this
device
5
UF-216 water Filtration system
A.J. Antunes & Co.
Specifications (continued)
Permeate
Outlet
Drain
Pulse
Controller
Mounting
Bracket
Filter
Housing
Flush Button
Inlet
Figure 1. Components
6
P/N 1011078 Rev. B 03/12
UF-216 water filtration system
A.J. Antunes & Co.
Overview
Overview
The UF-216 system operates in two modes:
• Normal Operation Mode
• Flush Mode
During Normal Operation Mode, water enters the Inlet
and flows through the Ultra Filter before exiting the
Permeate Outlet as usable product water.
During Flush Mode, the Drain Valve opens and water
entering the Inlet flushes and cleans the Ultra Filter
membrane by removing any debris collecting on the
membrane wall.
The Drain Valve is only powered during Flush Mode.
NOTE: Do NOT unplug the power cord or turn off
the system during Flush Mode. If there is a power
outage or the system is unplugged, water will continue to be filtered but the system will NOT flush.
This could cause the Ultra Filter to plug prematurely and may void the warranty.
Figure 2. UF-216 System
The flush is automated by the controller to last 10
seconds and take place in one hour intervals. This
interval can be changed (see Changing the Interval
Setting in the Maintenance section of this manual).
Caution
Changing the flush interval can cause the Ultra
Filter to plug prematurely and may void the warranty. Consult the factory for more information.
Manual Flushing
A manual flush can be activated at any time by pressing
the FLUSH button.
When the FLUSH button is pressed, the Flush LED on
the controller flashes and the Drain Valve opens for 10
seconds. After flushing is complete, the Drain Valve will
close, the Flush LED will stop flashing and the unit will
automatically return to Normal Operation Mode.
NOTE: A manual flush will not affect the interval
flush setting.
P/N 1011078 Rev. B 03/12
7
UF-216 water Filtration system
A.J. Antunes & Co.
Installation
Unpacking
Plumbing
1. Remove the system and all packing materials
from the shipping carton.
NOTE: This unit is designed to use tap water not to
exceed 100°F (38°C) or 100 psig (690 kPa).
2. Remove all packing materials and protective
coverings from the system
The UF-216 system uses the following connections
(Figure 1):
3. Remove the information packet. To prevent any
delay in obtaining warranty coverage, fill out and
mail the warranty card.
NOTE: If any parts are damaged, contact A.J.
Antunes & Co. IMMEDIATELY at 1-800-253-2991 or
1-630-784-1000.
General
When placing the unit into service, pay attention to the
following guidelines:
Suggested Tools and Supplies for Installation
If soldered plumbing is used, do NOT apply heat to,
or near, the filtration system. The use of union (O-ring
seal) connections is highly recommended for ease of
installation and future servicing.
The following tools and supplies are suggested to make
the installation easier:
Screwdriver
Drill with bits
Tape measure
Pipe wrenches
Strap wrench (up
to 3” diameter)
1/2” NPT
1/2” NPT
1/2” NPT
Do NOT over tighten the connections. It is recommended that plastic fittings be used when connecting to
the plastic connections of the system. This will reduce
the possibility of cracking the connections due to overtightening.
• Do NOT immerse cord or plug in water.
• Keep cord away from heated surfaces.
•
•
•
•
•
Water Inlet Permeate (Product Water)
Drain When making a plumbing connection to the system,
remember to use a back-up wrench on the supporting
plumbing. Always use a good quality, approved pipe
sealant or thread seal tape on pipe threads. Be careful
not to get the pipe sealant inside the pipe when making
the connections.
Equipment Setup
•
•
•
• Adjustable wrenches
• Level
• Two gallon bucket
• Pipe dope or thread seal tape
• Fresh 5 1/4% liquid chlorine bleach
IMPORTANT
Commonwealth of Massachusetts Plumbing Code
248 CMR shall be adhered to. The use of saddle
valves are not permitted, please consult your local
plumber.
Electrical
Caution
This equipment is to be installed to comply with
the basic plumbing code of the Building Officials
and Code Administrators, Inc. (BOCA) and the
Food Service Sanitation Manual of the Food and
Drug Administration (FDA).
Ensure that the line voltage corresponds to the stated
voltage on the units specification label. Make sure that
the plug on the power cord from the system and the
outlet match. For proper operation, and to ensure the
highest quality water from the system, make sure that
the system is not connected to a switched electrical
outlet.
Caution
Water pressure must not exceed 100 psig (690
kPa). To reduce water pressure, install a water
pressure regulator and set water pressure to suit
application. Note that the trans membrane pressure must not exceed 45 psi (310 kPa).
8
P/N 1011078 Rev. B 03/12
UF-216 water filtration system
A.J. Antunes & Co.
Installation (continued)
Mounting the System
Inlet Water Plumbing
The UF-216 system comes with a Mounting Bracket to
mount the system securely. When mounting the system,
pay attention to the following guidelines:
The Inlet water plumbing line should be 3/4” NPT or
larger. A shutoff valve (not supplied) should be installed
in the line leading to the system. The valve should be
mounted close to the system inlet and sized properly for
the inlet plumbing line.
•
Note the location of the water supply, drain, and
an appropriate electrical outlet when choosing a
mounting location.
•
Allow sufficient access for cartridge replacement.
•
Mount the system near but NOT above an appropriate electrical outlet.
•
Do NOT mount the system above any electrical
equipment or items that may be damaged if they
get wet.
•
Mount the system near a drain for flushing operations.
•
Mount the system before all consumable water
filtration processes.
•
Secure the Mounting Bracket into wall studs or with
the appropriate heavy duty mounting hardware.
An optional “T” or Cross Fitting with cap or plug can be
installed between the Inlet Valve and the System Inlet.
This fitting can be used for draining and sanitizing the
system and downstream plumbing.
The system should only be connected to the cold water
line.
Before connecting the fitting to the System Inlet, the
plumbing to the system must be flushed clear of all
debris. Hold a bucket at the inlet water line and slowly
open the Inlet Water Valve. Allow the pipe to flush until
all debris is removed.
The system is pre-assembled to a Mounting Bracket.
The Mounting Bracket has mounting holes to secure
the bottom of the system to the wall.
P/N 1011078 Rev. B 03/12
9
UF-216 water Filtration system
A.J. Antunes & Co.
Installation (continued)
Permeate Line Plumbing
Secure
End
To ensure the highest quality and safest water, it is
recommended that a check valve (to prevent backflow)
be installed in the water line after the permeate connection. This will help prevent possible contamination of the
filter system due to other equipment downstream. The
check valve (not supplied) should be mounted close to
the system outlet, and sized properly for the plumbing
line. Check with local codes for the proper specification.
2” (5.1 cm)
minimum
Standpipe
A shutoff valve (not supplied) should be installed in the
filtered water line leading from the system. The valve
should be mounted close to the system outlet and sized
properly for the plumbing line. This valve will allow for
easier servicing and future cartridge replacement.
Drain
Drain Valve Connection
Drain Line
from System
The drain line is for flushing particle buildup out of the
system during self cleaning. When connecting the drain
line, pay attention to the following guidelines:
Secure
End
• The drain line plumbing must be able support the
flow rate whenever the system flushes. This flow
rate is dependent on the inlet water pressure, inlet
pipe size, and system.
Floor
Drain
• The drain line leading out of the system must be
as short as possible and slope downwards without
any kinks or loops.
• The drain used must not be blocked or restricted.
• The drain used must be as large or larger than
the drain line plumbing.
2” (5.1 cm)
minimum
Figure 3. Proper Drain Plumbing
• The drain line plumbing must be position and
secured at least 2 inches above the drain (Figure
3). This air gap protects the system from contamination in the event of a backed-up drain.
Drain Line
from System
Starting the Controller
1. Select the proper AC plug for your electrical outlet
and install it onto the power supply.
2. Plug the appropriate end of the power cord into
the controller.
3. Plug the other end of the power cord into the electrical outlet. The LEDs on the controller will light up.
4. The controller automatically enters Flush Mode
and the Flush LED starts to flash.
5. When flushing is complete, the Flush LED will
stop flashing and one or more LEDs will remain lit,
indicating the unit has power and which interval is
selected in the controller.
10
P/N 1011078 Rev. B 03/12
UF-216 water filtration system
A.J. Antunes & Co.
Installation (continued)
Rinsing the Ultra Filter Cartridge
Sanitizing the System and Lines
The Ultra Filter Cartridge must be rinsed before the system is used to remove any air and protective solution.
The plumbing must be sanitized to eliminate possible
contamination that may have occurred during the installation process.
NOTE: Ultra Filter Cartridge must be rinsed to drain
before use. Rinsing to drain removes storage solution and air. Do NOT rinse into carbon if present.
Carbon life and/or performance may be affected.
1. Direct water from the Permeate Outlet to a drain.
One ounce (30 ml) of liquid chlorine bleach (regular
bleach, unscented 6% sodium hypochlorite) can be
used to sanitize the plumbing. The amount of bleach
needed depends on the system and the amount of
plumbing downstream of the system.
2. Open the tap or faucet closest downstream to the
filter system.
NOTE: Follow the handling and safety instructions
supplied with the bleach.
3. Slowly open the inlet water valve and allow water
to enter the system.
1. Follow the steps in the Rinsing the Ultra Filter
Cartridge in the Installation section of this manual.
4. Press the FLUSH button. The Drain Valve will
open and air and water will come out of the drain
line. Repeat six times to ensure all air and storage solution are flushed out of the Ultra Filter
Cartridge.
2. Turn off the water to the system.
3. Open the faucet or tap closest downstream to the
system.
4. Close the Inlet Water Valve and allow the system
to depressurize.
5. Allow water to continue to run through the system
and out the faucet for 15 minutes.
5. Place a bucket under the “T” or cross fitting at the
inlet connection to the system. Open the inlet drain
valve or unscrew the cap to drain the system.
6. Inspect the unit for any leaks and repair as
needed.
6. Press the FLUSH button to help drain the system.
7. After 15 minutes with water flow, close the tap or
faucet and let the system stand without water flow
for 15 minutes to allow trapped air to come out of
the hollow fibers of the Ultra Filter Cartridge.
7. When the water flow out of the inlet fitting stops,
close the inlet drain valve and pour the liquid
bleach into the inlet connection fitting. Be careful
not to spill bleach onto clothing or skin. You may
want to add the bleach using a cup. Reattach the
cap on the fitting.
8. After 15 minutes without water flow, open the tap
or faucet for five minutes to flush out the trapped
air.
8. Slowly open the inlet water valve and allow water
to flow out of the tap until the smell of bleach is
present.
9. Close the tap or faucet.
10. Press the FLUSH button to open the Drain Valve.
Repeat six times to ensure any remaining air is
flushed out of the system.
9. Immediately close the tap and let the system
stand with no water flow for at least 15 minutes to
allow the bleach to sanitize the pipes.
10. After 15 minutes without water flow, open the tap
and flush until the presence of bleach is gone. All
other taps should be opened to flush any bleach
from the plumbing. Close the taps.
11. Press the FLUSH button to complete the flushing
process.
P/N 1011078 Rev. B 03/12
11
UF-216 water Filtration system
A.J. Antunes & Co.
Maintenance
Replacing the Ultra Filter Cartridge
1. Open the faucet or tap closest downstream to the
filtration system.
End Cap
2. Close the Inlet Water Valve and allow the system
to depressurize.
3. Place a bucket under the strainer at the inlet
connection to the system. Open the strainer by
unscrewing the cap. Water will flow out of the
strainer as the system drains.
Permeate
Port
Connection
4. Press the FLUSH button to help drain the system.
5. Reattach the cap on the strainer when the water
flow stops. Unplug the power cord.
Cartridge
Bracket
6. Using a strap wrench (up to 6” capacity), loosen
the top and bottom End Caps. Do NOT remove
the top and bottom End Caps yet.
Cartridge
7. Disconnect the Permeate Port Connection.
8. Using a screwdriver, remove the screws from the
Cartridge Bracket and set the bracket and screws
aside.
Figure 4. Replacing the Ultra Filter Cartridge
System Sanitization
9. Unscrew the End Caps from the cartridge.
The system and downstream plumbing should be sanitized at least once a year. When necessary, follow the
procedure in Sanitizing the System and Lines in the
Installation section of this manual.
10. Install a new cartridge to the system using the
cartridge bracket and screws from Step 8.
11. Connect the Permeate Port Connection.
12. Inspect the O-rings to ensure they are clean and
not splitting or cut. For all O-rings, ensure they are
lubricated with an approved food grade lubricant
acceptable for drinking water use.
13. Screw each End Cap onto the cartridge. Tighten
with a strap wrench if necessary.
14. Plug in the power cord.
15. Open the Inlet Water Valve and allow the system
to pressurize.
16. Rinse the new Ultra Filter Cartridge before
placing the system back into operation. Follow
the Rinsing the Ultra Filter Cartridge and
Sanitizing the System and Lines procedures in
the Installation section of this manual to complete
the cartridge change.
17. When rinsing is complete, repressurize the
system.
12
P/N 1011078 Rev. B 03/12
UF-216 water filtration system
A.J. Antunes & Co.
maintenance (continued)
Changing the Interval Setting
Caution
Changing the flush interval can cause the Ultra
Filter to plug prematurely and may void the warranty. Consult the factory for more information.
Though not recommended, the Interval Setting on the
controller can be changed. If the setting must be
changed, use the chart below. Press and hold the corresponding button. After 5 seconds, the Button LED will
turn on. After 10 seconds, the Flush LED will also turn
on.
Flush
Interval
Button
Hold Time
Button
LED
Flush
LED
15 minutes
A
10 seconds
On
On
30 minutes
B
10 seconds
On
On
45 minutes
C
10 seconds
On
On
1 hour
A
5 seconds
On
Off
4 hour
B
5 seconds
On
Off
6 hours
C
5 seconds
On
Off
12 hours
D
5 seconds
On
Off
24 hours
D
10 seconds
On
On
Figure 5. Controller
Resetting the Timer Program
During the normal operation, the system will flush
according to the set interval. It is possible the system
will flush at a time of high water use. If this poses a
problem, the controller can be reset. Unplug the power
supply, wait for 5 seconds, and then plug the power
supply in. When power is restored to the controller, it
will automatically enter Flush Mode. The controller will
then begin timing from the point when power is restored
based on the interval setting selected.
P/N 1011078 Rev. B 03/12
13
UF-216 water Filtration system
A.J. Antunes & Co.
Troubleshooting
Problem
Possible Cause
Corrective Action
Unit does not have power.
The power cord is not correctly
plugged in.
Plug power cord in correctly.
The Control Display is blank.
The power cord is not correctly
plugged in.
Plug power cord in correctly.
Control Board is inoperable.
Transformer is inoperable.
Contact your maintenance person or
Authorized Service agency.
Inlet Valve closed
Open the Inlet Valve
Inlet Strainer is plugged
Clean/replace Inlet Strainer
End of the capillaries plugged
Clean/replace Ultra Filter Cartridge
See above.
See above.
The system may be in a flush cycle.
Wait for the flush cycle to end.
Flushing program not set correctly
for water conditions.
Decrease the flush interval (refer to the
Operation section of this manual).
Drain Valve is stuck open.
Replace/rebuild the Drain Valve.
The inlet water pressure is too low.
Boost the inlet water pressure/replace
pipes.
Storage/shipping solution not completely rinsed out of system.
Rinse system for a longer period of time.
Biological growth in pipes.
Sanitize plumbing.
Water conditions changed.
Consider installing taste and odor filtration.
Broken capillary in Filter Cartridge.
Replace Filter Cartridge.
Drain Valve stuck open.
Replace/rebuild the Drain Valve.
Controller sending continuous signal
to valve.
Replace the controller.
Flush occurs at time of high
water usage.
The Flush Interval is set to interfere
with water use.
Change Flush Interval. Unplug unit and
plug in at a time of lower water usage.
Water splashes at drain during flush.
Drain line not positioned properly.
Reposition the end of the drain line.
Water leaks at the ends of the
Filter Cartridge after changing
cartridges.
Cartridge end connections are not
tight enough.
Tighten with wrench if necessary.
O-rings not lubricated.
Lubricate O-rings with food-grade lubricant.
O-rings are split, cut, or twisted
Replace O-rings.
Permeate port is not tight enough
Tighten, with wrench if necessary.
O-ring not lubricated.
Lubricate O-ring with food-grade lubricant.
O-ring split, cut, or twisted.
Replace O-ring.
Fitting broken or loose.
Retighten or replace the fitting.
Not enough pipe thread sealant
used.
Redo the fitting with the proper amount of
sealant.
No water comes out of the filter system
Low water flow/pressure out
of system
Water tastes bad.
Flush runs continuously.
Water leaks from Permeate
port.
Water leaks from system fitting or connection.
14
P/N 1011078 Rev. B 03/12
UF-216 water filtration system
A.J. Antunes & Co.
Replacement Parts
Replacement Parts can be purchased from an authorized dealer. Contact
A.J. Antunes & Co. at 1-630-754-1000 or toll free in the United States at 1-800-253-2991.
Item
9
10
11
2
16
3
4
12
8
6
7
5
4
13
14
3
2
1
P/N 1011078 Rev. B 03/12
15
Part
No.
1
2
3
4
5
6
7
8
9
10
2190133
2180177
2180173
0200219
2090120
0503981
308P157
7000360
2070123
2070132
11
12
13
14
15
16
4040189
0505948
0012357
0012146
0700769
2190169
Description
Strainer, Tee 1/2” NPT
End Cap Filter, 2”
Slide Connector, 2”
O-ring, 2”
Cartridge Filter 2” x 16”
Filter Clamp, 2”
Screw Tap #8-32 x 3/8” (Pkg. of 10)
Permeate Assembly
90° Street Elbow 1/2” NPT
Reducer Bushing
3/4” NPT to 1/2” NPT
Solenoid Valve, 24 VDC, 3/4” NPT
Mounting Bracket
Universal Pulse Controller
Power Adapter
Wire Harness (not shown)
Reducer Bushing
3/4” NPT to 1/2” NPT
Qty.
1
2
2
4
1
1
1
1
1
1
1
1
1
1
1
Limited Warranty
Equipment manufactured by A.J. Antunes & Co. has been constructed of the finest materials available and manufactured to high quality standards. These units are warranted to be free from defects
in materials and workmanship for a period of one year from date of purchase under normal use and
service, and when installed in accordance with manufacturer’s recommendations*. The ultra filtration
membrane cartridge is warranted under the same terms and conditions on a prorated basis for 24
months from date of purchase.
*To ensure continued proper operation of the units, follow the maintenance procedure outlined in the
Owner’s Manual.
1. This warranty does not cover failures due to improper system installation, defects caused by improper
storage or handling prior to placing of the equipment into service. This warranty does not include
overtime charges or work done by unauthorized service agencies or personnel. This warranty does
not cover normal maintenance, calibration, or regular adjustments as specified in operating and maintenance instructions of this manual, and/or labor involved in moving adjacent objects to gain access to
the Equipment.
2. A.J. Antunes & Co. reserves the right to make changes in design or add any improvements on any
product. The right is always reserved to modify equipment because of factors beyond our control and
government regulations. Changes to update equipment do not constitute a warranty charge.
3.If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier.
Careful inspection should be made of the shipment as soon as it arrives and visible damage should
be noted upon the carrier’s documentation. Damage should be reported to the carrier. This damage
is not covered under this warranty.
4.This warranty is exclusive and is in lieu of all other warranties, expressed or implied, including any implied warranty or merchantability or fitness for a particular purpose, each of which is hereby expressly disclaimed. The remedies described above are exclusive and in no event shall A.J. ANtunes & CO.
be liable for special consequential or incidental damages for the breach or delay in performance of this warranty.
Prices and specifications are subject to change without notice.