Baotian BT49QT-11 User manual

BT49QT-12 Tanco – User Manual, Service Schedule & History
Introduction
Welcome to your new BAOTIAN BT49QT-12 (Tanco), which has been developed by BAOTIAN
MOTORCYCLE INDUSTRIAL CO. LTD. We hope you enjoy your new Baotian BT49QT-12 (Tanco).
This owner’s handbook contains information necessary:
• to enable you to get to know your Baotian BT49QT-12 (Tanco), to use it to the best advantage and to
benefit from all the latest developments which it incorporates.
• to ensure that it always give the best performance by following the simple, but strict, advice concerning
regular maintenance.
• to enable you to deal quickly with minor faults not requiring specialist attention.
It is well worth taking a few minutes to read this handbook to familiarise yourself with the information and
guidelines it contains about the BT49QT-12 (Tanco) and its features. If certain points are still unclear, the
technicians at your local Baotian dealer will be only too pleased to provide you with any additional information
you require.
IMPORTANT
Please make sure that an initial inspection is conducted after the first 300 km
and thereafter in accordance with service schedule.
This motorcycle has been designed and manufactured in full compliance with EU Safety Standards.
The maximum speed is 45km/h. Do not change any parts without professional advice.
CONTENTS
Guidance............................................................................................................................................................1
Position of parts .................................................................................................................................................3
Controlling parts.................................................................................................................................................4
Fuel tank ............................................................................................................................................................6
Fuel and engine oil ............................................................................................................................................6
Starting pedal.....................................................................................................................................................6
Pre-riding inspection ..........................................................................................................................................7
Engine starting .................................................................................................................................................. 8
Running-in..........................................................................................................................................................9
Regular maintenance.......................................................................................................................................10
Technical Parameters .....................................................................................................................................15
Electrical Circuit Chart .....................................................................................................................................17
Guidance
Please keep safety in mind and observe the regulations of transportation while enjoying your ride.
Pay attention to the following rules:
1. Pre-riding inspection
Please read the details in the relevant chapter for
your safety.
IMPORTANT
It is dangerous to drive on wet roads.
Do not make any abrupt turning while
accelerating and keep a safe distance from
other vehicles on the road.
2. Helmet
Do wear a helmet at all times while riding the
motorcycle.
3. Being familiar with motorcycle operation
It is of great importance to ensure your safety at
all times, especially whilst becoming familiar with
your motorcycle .
4. Speed limitation
Drive at appropriate speed for the road
conditions, the weather and your driving skill.
1
5. Positions of the numbers
When your motorcycle needs to be inspected,
repaired or undertake any service, these
numbers will assist your Baotian Dealer when
servicing your motorcycle. Please note down
your numbers here:
The frame number: ................................................
The engine number: .............................................
2
1
2
3
4
5
6
7
8
Front signal light
Left front turning light
Head light
Rear brake lever
Rear-view mirrors
Left switches
Seat lock
Left rear turning light
9
10
11
12
14
15
16
17
Starting pedal
Muffler
Right rear turning light
Rear light
Main stand
Helmet hook
Throttle control lever
Meters
3
18
19
20
21
22
23
24
Light switches
Front brake lever
Ignition switch
Right front turning light
Brake assembly
Brake disc
Hand hold
1. Rear brake lever
A. Horn button
B. Turning signal switch
Hold it tight and the rear brake works
Left turning light
➯
➯ right turning light
C. Switch for high/low beam lights
3. Meters and indicating lights
2. Switches on the left handle
A. Indicates the speed in Km/h and Mph
B. Indicates total distance the motorcycle has run
C. Left turning light indicator
D. High beam indicator
E. Right turning light indicator
F. Fuel gauge
4
4. Front brake lever
6. Ignition switch
Press it tightly and the front brake works.
---ON
---OFF
---LOCK
5. Switches on the right
ON
OFF
The whole circuit is cut. Engine and lights
cannot be operated and the key can be
taken out.
LOCK Turn the steering handle fully to the left,
slightly press the key and turn it to the
position lock . Then the key can be taken
out.
A. Head light switch
B. Electric starting button
C. Off switch
When the ignition switch is at ON position, hold
the brake and press the electric starting button
and then the engine starts.
Engine can be started and all the lights can
be operated. The key cannot be taken out.
5
Fuel and engine oil
Fuel tank
A. Petrol
Usage of the fuel tank lock:
Ensure unleaded petrol is used at all times.7
1. Turn the little cap on the fuel cap clockwise.
Insert the key and turn the key clockwise and
take out the fuel cap.
B. Engine oil
2. Align the lock tongue on fuel cap with the notch on
fuel tank, press the fuel cap and lock it.
SAE-15w/40 SF
20w/40-20w/50
15w/40-15w/50
10w/30
10w/40
-10
Starting lever
T
20
0
20
10
40
60
30
80
Starting lever is for kick starting the engine.
Warning:
◆ Turn off the engine when refilling the tank.
◆ Turn off the cap slowly.
◆ Don’t overfill the fuel over the designated scale
◆ Do not add anything into the petrol.
6
40 C
100 F
Pre-riding inspection
Please check the following parts before you drive.
No.
Items
Inspection content
2
Brake system
1.Travel of the front brake and the rear brake. 2. No damage to the cable
2. Flexible function
1
Steering handle bar
1.Flexibility. 2. No gap or loose appearance
3
Tyres
1. Correct pressure. 2. No splits in rubber
5
Engine oil
Sufficient engine oil
Horn
Workable
4
6
7
8
9
10
Fuel
Lights
Sufficient fuel
Workable
Gear oil
Sufficient oil
All the bolts and nuts
Not loose.
Throttle
1. Proper gap
2. Flexible function 3. Smooth throttle control function.
7
Engine starting
3. Engine Starting
1. Please check the volume of engine oil and fuel
before starting. The main stand should be stood
up while starting the engine.
Grip the brake lever and press the starter button
and then the engine will start.
2. Turn the ignition switch to the “ON” position.
Warning:
◆ Grip the rear brake lever to prevent forward
motion whilst starting
8
Warning:
Warning:
◆ 5 seconds is the maximum limit for each
starting and 10 seconds is the minimum
interval.
◆ After the engine has started, the kick start
pedal should be taken back to its original
position. Otherwise, it will affect the driver’s
safety.
◆ Stop pressing the starting button immediately
after the engine starts.
◆ Don’t start the engine in enclosed spaces, as
this can create Carbon Monoxide which can
cause loss of life.
◆ Do not press the starting button while the
engine is running, or the starter motor will be
damaged.
◆ The electric start will not operate without the
brake lever applied firmly.
Running in
To maintain your motorcycle running in a good
condition, please follow the below rules during the
new running-in period.
◆ When using electric starting, don’t operate the
starting motor continually, or it may cause
damage to the starter motor and the battery.
◆ Warm up the engine after cold starting (about
3 minutes).
Distance (km)
Speed limitation (km/h)- (mph)
300-1000
35
0-300
4. Kick Starting
Grip the brake lever, kick the kick start pedal
downwards 2 or 3 times in rapid succession.
1000——-
9
25
≤45
3. Air cleaner
1. Battery
•
12V/4Ah battery
•
Place the ignition switch to OFF position before
battery replacement.
•
•
•
When the voltage is less than 11.5V, please use
kicking start in stead of electric starting.
Electrode identification: “+”-red line, “-“-black line.
Replace the battery every 4 years.
A: Remove 6 tightening screws of air cleaner cover.
Remove air cleaner cover.
2. Carburetor and idle speed adjustment
•
•
B: Take out the sponge core.
Keep the engine warmed up for 2-3 minutes.
CLEANING:
Adjust the idling speed screw to set the engine at
speed if 1900 ±100 rpm. The idling speed
adjusting screw is following:.
Pour the non-inflammable detergent into a basin
and immerse the sponge core into the detergent.
Press the core to squeeze the detergent out of it
by hand. Never twist the filter it in case it is
broken.
Immerse the core into filter oil.
10
Squeeze the excess oil out but keep it lightly
oiled. If it has been damaged, please replace a
new one.
NOTE: Do not clean it with any oil or water.
4. Spark plug
•
Clean the carbon deposit on the spark plug with a
piece of hard wire or steel needle.
•
Use A7RC when replacement is needed.
•
6. Engine oil
Replace the engine oil with engine warmed up.
Adjust the gap to 0.6-0.7mm with a feeler gauge.
Remove the oil dipstick.
Remove the oil plug for displacement to drain the
used oil.
5. Fuel
Reinstall the oil plug for displacement, paying
attention to be tightened .
Always refill with unleaded petrol.
Refill 0.8 L recommended fresh engine oil.
⑤ Fasten all the nuts and screws.
Try to refill before the needle reaches the red
zone of the gauge.
11
7. Brake system
_
Normal free travel of the brake lever is about
2-5mm.
◆ FREE TRAVEL means the distance
between the positions from free status to
the beginning performance of the brake.
◆ Pay attention to the sensitivity of the
brake.
1. The front brake (disk brake)
Disk brake
◆Grip the brake lever and check the wear and
tear indicator. If the indicator nearly touched
the brake disc, please ask your Baotian
Dealer to change the brake pads.
2. The rear brake (drum brake)
Turn the adjusting nut to get a proper travel.
Normal free travel of the brake lever is
about 10-20mm.
◆Check the following items of brake system
before driving the motorcycle:
Check if there are any leakages.
Check if there are any leakages or cracks on
the hydraulic hose.
The brake lever should be kept with a certain
∼20mm.
free travel of 10∼
Wear of the brake pads.
12
8. Tyres
Brake fluid level
•
•
It has been filled with the special brake fluid
before the motorcycle leaves the factory. Fluid
should only ever be replace or filled with DOT4
brake fluid. Never replace or mix other fluids,
otherwise it will damage the brake system.
Insufficient tyre pressure increases wear to them
and affects the riding stability. Please check the tyre
pressure and tread depth when carrying out regular
maintenance.
•
If the brake fluid level is insufficient, it might be
possible for air to enter into the brake system and
result in brake failure
•
Tyre pressure: front 250 KPa, rear 250 KPa.
Tread depth: It is suggested to replace a tyre
when the tread depth is less than 1.6mm.
Warning:
Warning:
◆ The standard tyre is 120/70-12 56J for front
and 130/70-12 58J for rear tyres. Another type
of tyre may cause instability
◆ Brake fluid is a corrosive material. It causes
damage to all painted material.
◆ If fluid is sprayed on the skin or eyes, it should
be washed immediately with clean cold water
and medical advice sought.
◆ Tyre inflation pressures and the general tyre
condition are extremely important to the
performance and safety of the motorcycle.
13
How to change gear oil
9. Starter motor
Check the fastening bolts and the contact
brushes, and replace them if necessary.
An inline fuse is located in the live wire from the
battery. When a light or circuit fails suddenly,
please check the fuse first.
•
Replacing capacity: 100ml
•
•
Take out the oil drain plug for draining, let out all
the dirty gear oil.
•
•
11. Gear oil
Please use the recommended gear oil:
SAE 5W/90
Stand up the main stand.
•
10. Fuse
•
•
Total capacity: 110ml
14
Take off the oil plug for refill.
Tighten the oil drain plug.
Refill with fresh gear oil and tighten the oil refill
plug.
After refilling, please make sure you have locked
the oil plugs and bolts.
Technical Parameters
Size
Weight
Capacity
Circuit system
Length
Width
Height
Wheel base
1850mm
680mm
1150mm
1300mm
Unloaded weight
Mass weight
88kg
242kg
Max. Speed
Slope
45km/h
≥6º
Spark plug
Battery
Fuse
Headlight
Turning lights
Brake light
Indicating lights
A7RC
12V / 5.7AH
10A
12V 35/35W
12V 10W
12V 21W / 5W
12V 5W
Volume of the fuel tank
Volume of the engine oil tank
4L
1L
15
Technical Parameters
Engine
Suspension
Brake system
Model
Type
Cylinder
Bore and stroke
Cylinder volume
Compression ratio
Max. power
Max. torque
Carburetor
Air cleaner
Ignition type
Starting mode
Cooling mode
Lubrication
139QMA
4 stroke
1
39 x 41.4mm
49ml
10.5:1
2.61 kW / 8000 (r/min)
3.56 NM / 5500 (r/min)
PZ18J
Sponge core
CDI
Electric / kick start
Forced air-cooled
Pressure spray
Front absorber
Variable-pitch spring & hydraulic damping
shock absorber
Variable-pitch spring & hydraulic damping
shock absorber
Rear cushion
Front disc brake, rear drum brake
Tyres
120/70-12 56J front tyre
130/70-12 58J rear tyre
16
17
Baotian Warranty
EXCLUSIONS:
1. No liability will be accepted:
In the event of a sudden mechanical or electrical failure please contact your supplying
dealer.
a. For faults reported after 14 days of being discovered.
b. For machines used in competition or time trials.
Your 24-month warranty covers your scooter/motorcycle in the event of mechanical
breakdown or component failure. The first 12 months of cover extends to the entire
scooter with the exceptions detailed below. For the second year, warranty is limited to
the covered engine and transmission components only.
c. For machines used for hire or rewards, including taxi, riding schools, couriers
etc.
d. For machines where non-standard parts have been fitted and customisation
made.
This cover is extended to the registered owner. In the event of change of ownership,
please send written advice within 14 days of change to Baotian UK, Casino Industrial
Estate, Canterbury Road, Wingham, Kent CT3 1NL. Please enclose copies of service
history to verify validity of warranty.
2. No liability will be accepted for damage caused by:
a. Neglect.
b. Corrosion.
c. Intrusion of foreign matter.
All parts are covered subject to the following exclusions:
d. Lack of servicing.
GENERAL
e. The effects of overheating.
All body panels including covers, cowlings, fairings, windshield, paintwork, trims and
seat. Routine replacement of parts such as lubricants, tyres and control cables.
f. Freezing.
g. Consequential damage, how so ever caused.
Electrical fuses, lights, lenses and bulbs, indicator assemblies, drive unit [variators],
drive belts and chains, sprockets, rubber gaiters, suspension, wheels, fuels hoses and
tank cap.
h. The use of incorrect grade fuel, incorrect lubricant or incorrect anti-freeze.
i. Neglect, abuse or wilful damage including continuing to ride the machine when
it is not mechanically sound.
Frame and stands, accident damage, corrosion. Steering locks, brake friction material,
brake levers.
j. Subjecting the machine to loads greater than manufacturer’s recommendation.
k. Fire, explosion, flood water damage, theft or attempted theft and any such
extreme cause.
ENGINE
Engine tuning and adjustments or any other parts, which deteriorate during normal
usage.
3. No liability will be accepted for:
a. The affects of poor repair.
Lubricants, coolant additives, filters and breathers, spark plugs and caps, brackets and
mountings, hoses and hose clips.
b. Parts that have been fitted incorrectly.
c. Parts not fitted as standard by the manufacturer.
CLUTCH
d. Investigatory or remedial work commenced prior to the replacement of
defective covered parts.
Frictional material where the condition is related to wear and tear.
e. Routine servicing or repair.
CONDITIONS & EXCLUSIONS
f. Any parts that have been previously reported during routine service as to be
requiring replacement.
The scooter/motorcycle must be serviced in accordance with the manufacturer’s
schedule. Services may only be carried out to a maximum of 150km before or after the
due distance. VAT receipts must be retained.
The rights as set out in this document are in addition to your legal rights and subject to
English law.
g. Death, bodily injury or loss of use or any consequential loss of whatever nature.
18
4. No liability is accepted for any damage caused by a road traffic accident or
collision or any road hazard whether or not insured under any motor insurance
or accidental damage policy caused by mechanical or electrical failure.
INITIAL INSPECTION
SERVICE 2
Date:
Date:
Mileage:
Mileage:
Dealer stamp:
Dealer stamp:
SERVICE 1
SERVICE 3
Date:
Date:
Mileage:
Mileage:
Dealer stamp:
Dealer stamp:
19
SERVICE 4
SERVICE 6
Date:
Date:
Mileage:
Mileage:
Dealer stamp:
Dealer stamp:
SERVICE 5
SERVICE 7
Date:
Date:
Mileage:
Mileage:
Dealer stamp:
Dealer stamp:
20
SERVICE 8
SERVICE 10
Date:
Date:
Mileage:
Mileage:
Dealer stamp:
Dealer stamp:
SERVICE 9
SERVICE 11
Date:
Date:
Mileage:
Mileage:
Dealer stamp:
Dealer stamp:
21
SERVICE 12
SERVICE 14
Date:
Date:
Mileage:
Mileage:
Dealer stamp:
Dealer stamp:
SERVICE 13
SERVICE 15
Date:
Date:
Mileage:
Mileage:
Dealer stamp:
Dealer stamp:
22
Maintenance Schedule
Engine Oil
PDI
Gear Oil
Battery
Spark Plug
Fuel Filter
Carb
Odometer Cable
Control Cables
Tyre Pressure
Tyres / Wheels
Brake Fluid
Brake System
Drive Belt
Replace
Replace
Oil Strainer
Air Filter
300 KM
Charge
Replace
Clean
Clean
Inspect
Inspect
Inspect
Inspect
Inspect
Adjust
Inspect
Inspect
Inspect
Replace
3,000 KM
Clean
Adjust
Lubricate
1,000 KM
Adjust
Inspect
Inspect
Clean
Adjust
Clean
Inspect
Adjust
Inspect
Inspect
Replace
Inspect
Replace
Clean
Clean
Inspect
Adjust
Replace
Replace
Inspect
Replace
Replace
Clean
Inspect
Inspect
Inspect
Inspect
Inspect
Adjust
Adjust
Inspect
Inspect
Inspect
Inspect
Lighting
Inspect
Inspect
Inspect
Inspect
Clean
Replace
Inspect
Inspect
Inspect
Inspect
Inspect
Inspect
23
Adjust
Inspect
Adjust
Inspect
Inspect
Inspect
Replace
Inspect
Replace
Inspect
Inspect
Inspect
Inspect
Inspect
Inspect
Inspect
Inspect
Inspect
Every 2
Years
Replace
Lubricate
Inspect
Suspension
Replace
Replace
Lubricate
Inspect
Inspect
Replace
Lubricate
Inspect
Inspect
Replace
12,000 KM
Lubricate
Headstock Bearings
All Bolts & Fixings
Replace
9,000 KM
Lubricate
Vaiator Rollers
Clutch
6,000 KM
Adjust
Inspect
Inspect
Replace
Replace
Inspect
Inspect
Inspect
Inspect
Inspect
Replace