STC-A33A
Product Specification
Small Cubic Type – VGA CCD
Monochrome Analog Camera
STC-A33A
Safety Precautions
CAUTION
CAUTION
CAUTION
RISK
OF ELECTRIC
RISK
OF
ELECTRIC
SHOCK SHOCK
NOT OPEN
DO NOT DO
OPEN
RISK OF ELECTRIC SHOCK
DO NOT OPEN
For U.S.A.
For U.S.A.
Warning:
Warning:
!! !
For U.S.A.
Warning:
This equipment
generates
and
usesfrequency
radio frequency
This
equipment
generates
and uses
radio
energy energy
and if and if
not installed
andproperly,
used properly,
I.e.,
inaccordance
strict accordance
the
not
installed
and used
I.e., in
strict
withand
thewith
This
equipment
generates
and uses
radio
frequency
energy
if
instruction
manual,
mayharmful
cause harmful
interference
to radio
instruction
manual,
mayproperly,
cause
to radio
not installed
and used
I.e., ininterference
strict accordance
with the
communications.
It hastested
been and
tested
and to
found
to comply
communications.
It has
found
comply
with thewith the
instruction manual,
maybeen
cause harmful
interference
to radio
limits
for aAClass
A computing
device
pursuant
to Subpart
J of Part
limits
for
a Class
computing
deviceand
pursuant
of Part
communications.
It
has been tested
foundto
toSubpart
comply Jwith
the
15 ofRules,
FCC Rules,
which
are designed
to provide
reasonable
15limits
of FCC
which
are
designed
to
provide
reasonable
for a Class A computing device pursuant to Subpart J of Part
protection against such interference when operated in a commercial
protection
interference
when
operatedreasonable
in a commercial
15 of FCCagainst
Rules,such
which
are designed
to provide
environment.
protection against such interference when operated in a commercial
environment.
environment.
CAUTION:
CAUTION:
TO REDUCE TH E RISK OF EL ECTRIC SHOCK, DO N OT
CAUTION:
TO
REDUCE TH E RISK OF EL ECTRIC SHOCK, DO N OT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
REMOVE
COVER
(OR BACK). NO USER SERVICEABLE
TO REDUCE
TH E RISK OF EL ECTRIC SHOCK, DO N OT
PARTS INSIDE.
PARTS
INSIDE.
REMOVE
COVER (OR BACK). NO USER SERVICEABLE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
PARTSSERVICING
INSIDE. TO QUALIFIED SERVICE PERSONNEL.
REFER
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
For Canada
For Canada
Warning:
For Canada
Warning:
Warning:
This digital apparatus does not exceed the Class A limits for radio
This digital
exceed
the Class
limits
forRadio
radio
noiseapparatus
emissionsdoes
fromnot
digital
apparatus
setAout
in the
Thisemissions
digital apparatus
does not
exceedset
theout
Class
A limits
noise
from
digital
apparatus
in Department
the
Radio forofradio
Interference
Regulations
of the Canadian
noise emissions
from digital
out in the Radio
Interference
Regulations
of theapparatus
Canadianset
Department
of
Communications.
Interference Regulations of the Canadian Department of
Communications.
Communications.
The li ghtning flash with arrowhea d
The lightning
flash with
arrowhea triangle,
d
symbol, within
an equilateral
The li ghtning
flash
with arrowhea
d
symbol,
an
equilateral
triangle,
i s within
i nt ended
t o al ert the
use r t o the
within
an equilateral
issymbol,
intended
to alert
the
use r triangle,
to“dangerous
the
pre sence
of uni
nsulated
i s sence
i nt ended
t o al ert the“dangerous
use r t o the
pre
v o lof
t a guninsulated
e ” w i t h i n t h e p r o du c t ’ s
sence
nsulated
v pre
o lta
genclosure
e ” of
w iuni
th in
e p “dangerous
rbe
o du
t ’ s ent
t hatthmay
ofc suffici
v o l t a g e ” w i t h i n t h e p r o du c t ’ s
enclosure
thatude
mayt obec onst
of sufficient
ma gnit
i tut e a ri sk of
enclosure t hat may be of suffici ent
ma gnitude
toshock
c onstitute
a risk of
electric
to persons.
ma gnit ude t o c onst i tut e a ri sk of
electric shock to persons.
electric shock to persons.
!!
The excl ama ti on poi nt wi t hi n a n
equilateral
triangle iswithin
intended to alert
The
The exclama
excl amation
ti onpoint
poi nt wi t hi na an n
the user to the
presence toofalert
import ant
equilateral
equilateraltriangle
triangleisisintended
intended to alert
operatingpresence
and maintenance (servicing)
the
theuser
usertotothe
the presenceofofimportant
import ant
i n st r u cmaintenance
t i o ns i n t h e l i t e r a t u r e
operating
operatingand
and maintenance(servicing)
(servicing)
the appliance.
i ni nststr uraccompanying
uc ctitoi onsns ini n t ht he e l il te
i t er ar at ut ur er e
accompanying
accompanyingthe
theappliance.
appliance.
WARNING:
WARNING:
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE
TO RAIN OR MOISTURE.
TO
TOPREVENT
PREVENTFIRE
FIREOR
ORSHOCK
SHOCKHAZARD,
HAZARD,DO
DONOT
NOTEXPOSE
EXPOSE
THIS
APPLIANCE
TO
RAIN
THIS APPLIANCE TO RAINOR
ORMOISTURE.
MOISTURE.
Product Precautions








Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling
or storage could damage the camera.
Do not pull or damage the camera cable.
During camera use, do not wrap he unit in any material. This will cause the internal temperature of the
unit to increase.
Do not expose the camera to moisture, or do not try to operate it in wet areas.
Do not operate the camera beyond its temperature, humidity and power source ratings.
While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or
contamination from getting in the CCD or filter area and scratching or damaging this area.
Do not keep the camera under the following conditions:
 In wet, moist, and high humidity areas
 Under hot direct sunlight
 In high temperature areas
 Near an object that releases a strong magnetic or electric field
 Areas with strong vibrations
Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not
scratch the surface of the glass.
Product Specification
2
Rev 2.1
STC-A33A
Copyright & Disclaimer
Sensor Technologies America, Inc. (DBA Sentech America) believes the contents and specifications of its website, catalog,
documentation and ads are correct; however, Sentech America provides no representation or warranty regarding such information or
product(s) contained therein. It is requested that Sentech America be given appropriate acknowledgement in any subsequent use of
such work by a third party.
While every effort has been made to ensure that the details contained in Sentech America’s website and all documentation are correct
and up-to-date, Sentech America assumes no liability, legal or otherwise for any errors in listings, specifications, part numbers,
process, software or model applications. Sentech America reserves the right to change specifications, product descriptions, product
quality, pricing and application at any time without prior written or oral notice. Any party using such information assumes all risk for
any and all damaged caused to themselves, a third party and/or property by virtue of incorrect information and/or failure of these
products. By installing and/or using a Sentech America software development kit or other similar product and/or information obtained
from Sentech America’s website, catalog, documentation or ads, you hereby accept and understand these stated terms and conditions.
Product Specification
3
Rev 2.1
STC-A33A
Content
I. Specifications ....................................................................................................................................................... 5-8
A. Electronic Specifications / Mechanical Specifications / Environmental Conditions ....................................................... 5
B. Rear Panel Specifications ................................................................................................................................................ 6
1. Connector Pin Assignment .......................................................................................................................................... 6
2. DIP Switch Settings...................................................................................................................................................... 7
3. External Sync ............................................................................................................................................................... 8
4. Gain Mode Setting ...................................................................................................................................................... 8
II. Dimensions ....................................................................................................................................................... 9-11
A. Dimensions ..................................................................................................................................................................... 9
B. Dimensions (Tripod) ...................................................................................................................................................... 10
C. Dimensions (Camera with Tripod) ................................................................................................................................ 11
Product Specification
4
Rev 2.1
STC-A33A
I. Specifications
A. Electronic Specifications / Mechanical Specifications / Environmental Conditions
Product
Imager
Total Picture Elements
Effective Picture Elements
Active Picture Elements
Chip Size
Cell Size
Scanning Systems
Scanning Method
Electronic
Specifications
Vertical Frequency
Horizontal Frequency
Pixel Frequency
S/N Ratio (Standard Deviation)
Minimum Scene Illumination
Sync. System
Video Output
DIP Switch
Shutter Speed
Communication
Gain
Gamma
Input Voltage
Power Supply
Consumption
Trigger Mode
Communication
Dimensions
Optical Filter
Optical Center Accuracy
Mechanical
Specifications
Material
Case
Tripod
Lens Mount
Interface Connector
Tripod
Weight
Temperature
and Humidity
Environmental
Conditions
Operational
Storage
Vibration
Shock
Standard Compliancy
RoHS
Product Specification
STC-A33A
1/3” Interline VGA Monochrome Progressive CCD: ICX424AL
692 (H) x 504 (V)
659 (H) x 494 (V)
VGA: 648 (H) x 494 (V)
5.79 (H) x 4.89 (V)
7.4 (H) x 7.4 (V) µm
Progressive
Full Scanning, Partial Full Scanning, ½ Partial Scanning,
¼ Partial Scanning, Variable Partial Scanning,
Binning, Binning Partial Scanning
Binning ½ Partial Scanning, Binning ¼ Partial Scanning
Binning Variable Partial Scanning
31.47 (30fps) / 62.94 (60fps) / 94.784 (90fps) Hz
15.7343 (30fps) / 31.4685 (60fps) / 47.2028 (90fps) kHz
12.2727 (30fps) / 24.5454 (60fps) / 36.8181 (90fps) MHz
56 dB (GAIN 0 dB)
1 Lux at F1.4
Internal / External
1.0 Vp-p / 75Ω, DC Coupling (0V)
OFF; 1/200; 1/500; 1/1000; 1/2000; 1/4000; 1/8000; 1/20,000 second
OFF; ½ to 1/100,000 sec. (Variable at every H and Clock)
0 to 27 dB
1.0 / 0.45
DC 12V ± 10%
Less than 1.8 W
Edge Preset Trigger (V-reset, Non-reset)
Pulse Width Trigger (V-reset, Non-reset)
RS232 via 12 Pin Connector
28(W) x 28(H) x 46.3(D)mm including lens mount and connector
No IR Cut Filter
Positional Accuracy in H and V directions: +/- 0.31mm
Front, Base, and Rear: Aluminum Die Cast (ADC12)
Cover: Steel Sheet Covered with Zinc
Polycarbonate ABS
C Mount
HR10A-10R-12PB (Hirose) or equivalent
Tripod can be attached to 4 plates
(4 screws on the bottom plate, 3 screws on the other 3 plates)
Approximately 52g (Camera: 43g, Tripod: 9g)
Temperature: -5 to 50:C; Relative Humidity: 0 to 85%
(No Condensation)
Temperature: -30 to 65:C; Relative Humidity: 0 to 90%
(No Condensation)
20Hz to 200Hz to 20Hz (5 min./cycle), Acceleration 10G,
3 Directions 30 Minutes Each
Acceleration 70G, Half Amplitude 6ms,
3 Directions 3 Times Each
EMS: EN61000-6-2, EMI: EN55011 (Class B)
RoHS Compliant
5
Rev 2.1
STC-A33A
B. Rear Panel Specifications
1. Connector Pin Assignment
12 Pin Connector
DIP Switch
Gain Mode Switch
Manual Gain Pot
External Sync (HD/VD)
Signal Impedance Switch
Figure 1
12 Pin Connector Assignment
The connector type: HR10A-10R-12PB (Hirose) or equivalent
Pin Assignment
No.
1
2
3
4
5
6
7
8
9
10
11
12
Figure 2
Signal types
Internal sync
External sysnc
GND
GND
+12V DC
+12V DC
VIDEO GND
VIDEO GND
VIDEO OUT
VIDEO OUT
HD GND
HD GND
HD OUT
HD IN
VD OUT
VD IN
GND
GND
TXD
TXD
WEN OUT
WEN OUT
TRG IN
TRG IN
RXD (Note)
RXD (Note)
*Note: Pin No.12 can be connected to GND
The camera settings can change by RS232C communication with No. 9 and 12.
Please refer the detail for the user’s guide.
Product Specification
6
Rev 2.1
STC-A33A
2. DIP Switch Settings (Refer to Dip Switch in Figure 1)
DIP Switch No. 1 to 3: Shutter Speed
1
O
2
N
3
4
DIP Switch No. 4 to 5: Reset Mode
5
6
7
DIP Switch No. 6: Trigger Polarity
8
9
0
DIP Switch No.7 to 8: Scanning Method
Figure 3
DIP Switch No.9: Sync. System
DIP Switch No.10: Binning
Product Specification
7
Rev 2.1
STC-A33A
3. External Sync. (HD/VD) signal impedance setting (See External Sync. in Figure 1)
ON:
OFF:
75Ohm termination
High impedance
4. Gain Mode Setting (See Gain Mode Switch in Fig. 1)
FIX:
MAN:
Product Specification
Fixed gain
Manual gain
The gain can be adjustable by the manual gain pot (See Manual Gain Pot in Fig. 1).
8
Rev 2.1
STC-A33A
II. Dimensions
A. Camera Dimensions
Unit: mm
Product Specification
9
Rev 2.1
STC-A33A
B. Tripod Dimensions
Tripod screw depth 5.5
33.5
22
12
24
(9)
2-M4 (P=0.7) depth 5.5
4
6.5
9.5
(10.5)
(10.5)
9.5
(R13.8)
Unit: mm
Product Specification
10
Rev 2.1
STC-A33A
C. Camera with Tripod Dimensions
Unit: mm
Product Specification
11
Rev 2.1
STC-A33A
Revisions
Revision
Date (D/M/Y)
Changes
Name
1.0
23/08/2006
Created Document
Sam Aimono
1.1
22/08/2006
Update whole document
Sam Aimono
1.2
19/09/2006
Change document structure
Sam Aimono
1.3
25/04/2007
1.4
01/10/2007
2.0
16/04/2008
Separate document from “Specification” to “Specification” and “User’s Guide”
Sam Aimono
2.1
12/05/2008
Edited English
Michelle Campbell
Product Specification
Update
1) Output timing chart
2) Connector
Update
1) Mechanical Specifications (optical center accuracy)
2) Communication Specifications (Add the initial data and the data range)
3) Tripod drawing (Change Japanese to English)
4) Camera Modes
12
Changes
Sam Aimono
Sam Aimono
Rev 2.1
STC-A33A
Sensor Technologies America, Inc.
1345 Valwood Pkwy, Suite 320
Carrollton, Texas 75006-6891
TEL (972) 481-9223 FAX (972) 481-9209
URL http://www.sentechamerica.com/
Sensor Technology Co., Ltd.
7F, Harada Center Building
9-17, Naka cho 4chrome
Atsugi-city, Kanagawa
243-0018 Japan
TEL +81-46-295-7061 FAX +81-46-295-7066
URL http://www.sentech.co.jp/
Taiwan Sensor Technology, Inc.
3F-6, No. 9, Aiguo W, Rd,. Jhong Jheng
District
Taipei City 100, Taiwan, R.O.C.
TEL 886-2-2383-2331 FAX 886-2-2370-8775
EMAIL: sentech0501@yahoo.com.tw
Product Specification
13
Rev 2.1