Datalogic QuickScan i Technical data

2983.book Page 1 Monday, January 12, 2009 12:43 PM
QuickScan® i
QD2100 Barcode Imager
Quick Reference Guide
2983.book Page 2 Monday, January 12, 2009 12:43 PM
Datalogic Scanning, Inc.
959 Terry Street
Eugene, Oregon 97402
Telephone: (541) 683-5700
Fax: (541) 345-7140
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior
written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic
Scanning”). Owners of Datalogic products are hereby granted a non-exclusive, revocable license to
reproduce and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this
documentation and shall ensure that all notices appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting
your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website (www.scanning.datalogic.com) or provided on appropriate media. If you visit our website and
would like to make comments or suggestions about this or other Datalogic publications, please let us
know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and
accurate, however, Datalogic reserves the right to change any specification at any time without prior
notice.
Datalogic is a registered trademark of Datalogic S.p.A. in many countries and the Datalogic logo is a
trademark of Datalogic S.p.A. All other brand and product names referred to herein may be trademarks
of their respective owners.
This product may be covered by one or more of the following patents: 4603262 • 4639606 • 4652750 • 4672215 • 4699447 •
4709369 • 4749879 • 4786798 • 4792666 • 4794240 • 4798943 • 4799164 • 4820911 • 4845349 • 4861972 • 4861973 • 4866257
• 4868836 • 4879456 • 4939355 • 4939356 • 4943127 • 4963719 • 4971176 • 4971177 • 4991692 • 5001406 • 5015831 •
5019697 • 5019698 • 5086879 • 5115120 • 5144118 • 5146463 • 5179270 • 5198649 • 5200597 • 5202784 • 5208449 • 5210397
• 5212371 • 5212372 • 5214270 • 5229590 • 5231293 • 5232185 • 5233169 • 5235168 • 5237161 • 5237162 • 5239165 •
5247161 • 5256864 • 5258604 • 5258699 • 5260554 • 5274219 • 5296689 • 5298728 • 5311000 • 5327451 • 5329103 • 5330370
• 5347113 • 5347121 • 5371361 • 5382783 • 5386105 • 5389917 • 5410108 • 5420410 • 5422472 • 5426507 • 5438187 •
5440110 • 5440111 • 5446271 • 5446749 • 5448050 • 5463211 • 5475206 • 5475207 • 5479011 • 5481098 • 5491328 • 5493108
• 5504350 • 5508505 • 5512740 • 5541397 • 5552593 • 5557095 • 5563402 • 5565668 • 5576531 • 5581707 • 5594231 •
5594441 • 5598070 • 5602376 • 5608201 • 5608399 • 5612529 • 5629510 • 5635699 • 5641958 • 5646391 • 5661435 • 5664231
• 5666045 • 5671374 • 5675138 • 5682028 • 5686716 • 5696370 • 5703347 • 5705802 • 5714750 • 5717194 • 5723852 •
5750976 • 5767502 • 5770847 • 5786581 • 5786585 • 5787103 • 5789732 • 5796222 • 5804809 • 5814803 • 5814804 • 5821721
• 5822343 • 5825009 • 5834708 • 5834750 • 5837983 • 5837988 • 5852286 • 5864129 • 5869827 • 5874722 • 5883370 •
5905249 • 5907147 • 5923023 • 5925868 • 5929421 • 5945670 • 5959284 • 5962838 • 5979769 • 6000619 • 6006991 • 6012639
• 6016135 • 6024284 • 6041374 • 6042012 • 6045044 • 6047889 • 6047894 • 6056198 • 6065676 • 6069696 • 6073849 •
6073851 • 6094288 • 6112993 • 6129279 • 6129282 • 6134039 • 6142376 • 6152368 • 6152372 • 6155488 • 6166375 • 6169614
• 6173894 • 6176429 • 6188500 • 6189784 • 6213397 • 6223986 • 6230975 • 6230976 • 6244510 • 6259545 • 6260763 •
6266175 • 6273336 • 6276605 • 6279829 • 6290134 • 6290135 • 6293467 • 6303927 • 6311895 • 6318634 • 6328216 • 6332576
• 6332577 • 6343741 • 6454168 • 6478224 • 6568598 • 6578765 • 6705527 • 6857567 • 6974084 • 6991169 • 7051940 •
7170414 • 7172123 • 7201322 • 7204422 • 7215493 • 7224540 • 7234641 • 7243850 • 7374092 • 601 26 118.6 • AU703547 •
D312631 • D313590 • D320011 • D320012 • D323492 • D330707 • D330708 • D349109 • D350127 • D350735 • D351149 •
D351150 • D352936 • D352937 • D352938 • D352939 • D358588 • D361565 • D372234 • D374630 • D374869 • D375493 •
D376357 • D377345 • D377346 • D377347 • D377348 • D388075 • D446524 • EP0256296 • EP0260155 • EP0260156 •
EP0295936 • EP0325469 • EP0349770 • EP0368254 • EP0442215 • EP0498366 • EP0531645 • EP0663643 • EP0698251 •
EP01330772 • GB2252333 • GB2284086 • GB2301691 • GB2304954 • GB2307093 • GB2308267 • GB2308678 • GB2319103 •
GB2333163 • GB2343079 • GB2344486 • GB2345568 • GB2354340 • ISR107546 • ISR118507 • ISR118508 • JP1962823 •
JP1971216 • JP2513442 • JP2732459 • JP2829331 • JP2953593 • JP2964278 • MEX185552 • MEX187245 • RE37166 •
RE40.071 • Other Patents Pending
2983.book Page 1 Monday, January 12, 2009 12:43 PM
Datalogic Scanning, Inc.
QUICKSCAN® PRODUCT SERIES END USER LICENSE
AGREEMENT
Notice to End User: The Datalogic Product you have acquired contains
embedded Software, which is integral to the product's operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed
to have accepted the terms and conditions of this Agreement. If you do not
intend to be bound to the terms of this Agreement, Datalogic is not willing to
license the Software to you, you may not use the Datalogic Product or the
Software, and you must contact the party from whom you acquired the Datalogic Product for instructions.
This End User Software License Agreement ("Agreement") is a legally binding
agreement governing the licensing of the Software and Documentation by Datalogic Scanning, Inc. and its Affiliates ("Datalogic") to the entity or person who
has purchased or otherwise acquired a Datalogic Product ("End User"). For
purposes of this Agreement, any software that is associated with a separate
end-user license agreement is licensed to you under the terms of that license
agreement. Datalogic and End User hereby agree as follows:
1. Definitions.
1.1 "Affiliate" means a business entity currently existing or later acquired that
controls, is controlled by, or is under common control with Datalogic
S.p.A.
1.2 "Documentation" means materials such as user's guides, program reference guides, quick reference guides, manuals, or similar materials
associated with or related to the Datalogic Product, whether in printed,
"online", or other form.
1.3 "Proprietary Information" means: (a) source code, object code, software,
documentation, and any related internal design, system design, data
base design, algorithms, technology, technical data or information,
implementation techniques, and trade secrets related to the Software,
(b) any other trade secrets marked appropriately or identified as proprietary or confidential, and (c) any information that End User, under the
circumstances, should recognize as confidential. Proprietary Information does not include any information that the receiving party can
establish was (1) in the public domain, (2) already in the receiving
party's possession or rightfully known prior to receipt, (3) rightfully
learned from a third party not in violation of any other's proprietary
rights, or (4) independently developed without access to Proprietary
Information.
1.4 "Datalogic Product" means the Datalogic® Quickscan® series scanner
product, including all embedded Software in and all Documentation
related to such product, which has been purchased or otherwise
acquired by End User, whether obtained directly or indirectly from Datalogic.
1.5 "Software" means any software or computer programs of Datalogic or its
third party licensors in machine readable form which is embedded in
the Datalogic Product, whether obtained directly or indirectly from Datalogic, including any replacement, update, upgrade, enhancement or
modification.
2. Scope Of License Granted.
2.1 Datalogic grants to End User a non-exclusive, non-transferable, perpetual
license to use the Software, solely on the Datalogic Product in which it
is embedded ("designated Datalogic Product"), in machine-readable
form only, solely for End User's internal business purposes. This Agreement does not convey ownership of the Software to End User. Title to
the Software shall be and remain with Datalogic or the third party from
whom Datalogic has obtained a licensed right. As used in this Agreement, the term "purchase" or its equivalents when applied to the Software shall mean "acquire under license." End User is not entitled to
Quick Reference Guide
1
2983.book Page 2 Monday, January 12, 2009 12:43 PM
2.2
receipt or use of the source code to any Software.
End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or remanufacture the Software, whether
modified or unmodified, nor sell, assign, sublicense, distribute, lend,
rent, give, or otherwise transfer the Software to any other person or
organization, for purposes other than as expressly provided in this
Agreement, without Datalogic's prior written consent.
3. Transfers, Support.
3.1
3.2
3.3
Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer, or other use of the Software on other than the
designated Datalogic Product will be a material breach of this Agreement. However, Datalogic may elect not to terminate this Agreement or
the granted licenses, but instead may elect to notify End User that End
User is deemed to have ordered and accepted a license for each
breaching use. End User shall pay Datalogic the applicable list price for
such licenses as of the date of such breach.
End User shall not sell, assign, sublicense, distribute, lend, rent, give,
or otherwise transfer the Datalogic Product to any third party unless
such third party agrees with Datalogic in writing to be bound by the
terms and conditions of this Agreement. Any such transfer of the Datalogic Product absent such agreement shall be null and void.
End User may obtain support for Software from Datalogic at Datalogic's
standard support fees and under Datalogic's standard support terms
and conditions in effect at the time the support is requested.
4. Intellectual Property.
End User acknowledges that the Software constitutes valuable trade secrets of
Datalogic or Datalogic's third party licensors and that the Software is protected
by intellectual property laws and treaties. The license set forth in this Agreement does not transfer to End User any ownership of Datalogic's or its third
party licensors' copyrights, patents, trademarks, service marks, trade secrets,
or other intellectual property rights and End User shall have no right to commence any legal actions to obtain such rights. End User shall not remove, modify, or take any other action that would obscure any copyright, trademark, patent
marking, or other intellectual property notices contained in or on the Datalogic
Product.
5. Proprietary Information.
5.1
5.2
5.3
End User acknowledges that Proprietary Information is the confidential,
proprietary, and trade secret property of Datalogic and Datalogic's third
party licensors and End User acquires no right or interest in any Proprietary Information.
End User shall not disclose, provide, or otherwise make available the
Proprietary Information of Datalogic or its third party licensors to any
person other than End User's authorized employees or agents who are
under confidentiality agreement, and End User shall not use the Proprietary Information other than in conjunction with use of the Datalogic
Product exclusively for End User's internal business purposes. End
User shall take steps to protect the Proprietary Information no less
securely than if it were End User's own intellectual property.
The provisions of this Proprietary Information Section shall survive and
continue for five (5) years after the termination of this Agreement.
6. Limited Warranty.
6.1
2
Datalogic warrants that, under normal use and operation, the Datalogic
Product will conform substantially to the applicable Documentation for
the period specified in the Documentation. During this period, for all
reproducible nonconformities for which Datalogic has been given written notice, Datalogic will use commercially reasonable efforts to remedy nonconformities verified by Datalogic. End User agrees to supply
Datalogic with all reasonably requested information and assistance
necessary to help Datalogic in remedying such nonconformities. For all
defects reported to Datalogic within the warranty period, Datalogic's liability is limited to providing End User with one copy of corrections or
QuickScan® i
2983.book Page 3 Monday, January 12, 2009 12:43 PM
6.2
responding to End User's problem reports according to Datalogic's
standard assistance practices. Datalogic does not warrant that the
product will meet End User's requirements or that use of the product
will be uninterrupted or error free, or that Datalogic's remedial efforts
will correct any nonconformance. This limited warranty does not cover
any product that have been subjected to damage or abuse, whether
intentionally, accidentally, or by neglect, or to unauthorized repair or
unauthorized installation, and shall be void if End User modifies the
product, uses the product in any manner other than as established in
the Documentation, or if End User breaches any of the provisions of
this Agreement.
EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC
PRODUCT IS PROVIDED "AS IS" AND DATALOGIC MAKES NO
WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WRITTEN OR
ORAL, WITH RESPECT TO THE PRODUCT, AND SPECIFICALLY
DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
7. Infringement.
7.1
7.2
7.3
7.4
Datalogic will defend End User against any claim in a lawsuit that the
Datalogic Product furnished hereunder infringe a United States patent
or copyright of a third party and Datalogic will pay any damages finally
awarded against End User by a court of competent jurisdiction that are
attributable to such claim or will pay End User's part of any settlement
that is attributable to such claim, provided, that 1) End User notifies
Datalogic promptly in writing of the claim, 2) Datalogic controls the
defense or settlement of the claim, and 3) End User cooperates fully
with Datalogic in such defense or settlement. All notices of a claim
should be sent to Datalogic Scanning, Inc., Legal Department, 959
Terry Street, Eugene, OR 97402.
In the defense or settlement of any such claim, Datalogic may, at its
option, 1) procure for End User the right to continue using the Datalogic
Product, 2) modify the Datalogic Product so that it becomes
non-infringing, 3) replace the Datalogic Product with an equivalent
product not subject to such claim, or 4) provide End User an opportunity to return the Datalogic Product and receive a refund of the purchase price paid, less a reasonable allowance for use.
Datalogic shall have no liability to End User for claims of infringement
based upon 1) the use of any Datalogic Product in combination with
any product which Datalogic has not either furnished or authorized for
use with such Datalogic Product 2) the use of any Datalogic Product
designed, manufactured, or modified to the specifications of End User,
or 3) End User's modification of the Datalogic Product without written
authorization from Datalogic.
THE FOREGOING STATES DATALOGIC'S COMPLETE AND ENTIRE
OBLIGATION CONCERNING CLAIMS OF PATENT, COPYRIGHT, OR
OTHER INTELLECTUAL PROPERTY INFRINGEMENT, CANCELS
AND SUPERCEDES ANY PRIOR AGREEMENTS, WHETHER ORAL
OR WRITTEN, BETWEEN THE PARTIES CONCERNING SUCH
CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY
PAST, CONTEMPORANEOUS, OR FUTURE AGREEMENTS OR
DEALINGS BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY
BOTH PARTIES.
8. Limitation Of Liability.
EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE
FOR ANY CLAIMS AGAINST END USER BY ANY OTHER PARTY. IN NO
EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY, WHETHER
BASED UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT
LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY OTHER BASIS,
EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DATALOGIC
PRODUCT. UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE
TO END USER OR ANY THIRD PARTY FOR LOST PROFITS, LOST DATA,
INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF DATALOGIC
Quick Reference Guide
3
2983.book Page 4 Monday, January 12, 2009 12:43 PM
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9. Government Restricted Rights; International Use.
9.1
9.2
Use, duplication, or disclosure of the Software by the U.S. Government
is subject to the restrictions for computer software developed at private
expense as set forth in the U.S. Federal Acquisition Regulations at FAR
52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013(c)(1)(ii), whichever is
applicable.
If End User is using the Datalogic Product outside of the United States,
End User must comply with the applicable local laws of the country in
which the Datalogic Product is used, with U.S. export control laws, and
with the English language version of this Agreement. The provisions of
the "United Nations Convention on International Sale of Goods" shall
not apply to this Agreement.
10. Termination.
10.1
10.2
Either party may terminate this Agreement or any license granted
under this Agreement at any time upon written notice if the other party
breaches any provision of this Agreement.
Upon termination of this Agreement, End User immediately shall cease
using any nonembedded software and shall return to Datalogic or
destroy all non-embedded software covered by this Agreement, and
shall furnish Datalogic with a certificate of compliance with this provision signed by an officer or authorized representative of End User. For
embedded software, End User agrees to sign a waiver prepared by
Datalogic concerning further use of the embedded Software. End
User's resumed or continued use of the embedded Software after termination shall constitute End User's agreement to be bound by the
terms and conditions of this Agreement for such use.
11. General Provisions.
11.1 Entire Agreement; Amendment. This document contains the entire
agreement between the parties relating to the licensing of the Software
and supersedes all prior or contemporaneous agreements, written or
oral, between the parties concerning the licensing of the Software. This
Agreement may not be changed, amended, or modified except by written document signed by Datalogic.
11.2 Notice. All notices required or authorized under this Agreement shall be
given in writing, and shall be effective when received, with evidence of
receipt. Notices to Datalogic shall be sent to the attention of Contract
Administration, Datalogic Scanning, Inc., 959 Terry Street, Eugene, OR
97402, or such other address as may be specified by Datalogic in writing.
11.3 Waiver. A party's failure to enforce any of the terms and conditions of this
Agreement shall not prevent the party's later enforcement of such
terms and conditions.
11.4 Governing Law; Venue: This Agreement and the rights of the parties
hereunder shall be governed by and construed in accordance with the
laws of the State of Oregon U.S.A, without regard to the rules governing conflicts of law. The state or federal courts of the State of Oregon
located in either Multnomah or Lane counties shall have exclusive jurisdiction over all matters regarding this Agreement, except that Datalogic
shall have the right, at its absolute discretion, to initiate proceedings in
the courts of any other state, country, or territory in which End User
resides, or in which any of End User's assets are located.
11.5 Attorneys' Fees. In the event an action is brought to enforce the terms
and conditions of this Agreement, the prevailing party shall be entitled
to reasonable attorneys' fees, both at trial and on appeal.
- END -
4
QuickScan® i
2983.book Page 5 Monday, January 12, 2009 12:43 PM
Software Product Policy
Software Product Policy
Datalogic reserves the right to ship its products with the latest version of software/firmware available. This provides our customers with the very latest in Datalogic software
technology.
The only exception to this policy is when the buyer has a signed contract with Datalogic
that clearly defines the terms and conditions for making software/firmware changes in
products shipped to the buyer.
Customers Under Software Support
Customers that elect to subscribe to Datalogic Software Maintenance and Support
Agreement will receive 30 days advance notification of: (1) the release of a new software
version; and/or (2) discontinuation of any prior software version that will no longer be
supported. Datalogic will provide maintenance for a fee that will assist customers in
transitioning to the next software version. If a customer is currently using the software
version being discontinued, the customer may elect to transition to any one of the
newer versions, depending on the hardware in use.
To arrange for a Software Maintenance and Support Agreement please contact your
Datalogic sales person.
Quick Reference Guide
5
2983.book Page 6 Monday, January 12, 2009 12:43 PM
NOTES
6
QuickScan® i
2983.book Page 1 Monday, January 12, 2009 12:43 PM
Connect/Disconnect Cable
1
Connect/Disconnect Cable
Connect Host Interface
2
Keyboard Wedge Interface
RS-232 Interface
USB Interface
IBM 46xx Interface
Quick Reference Guide1
2983.book Page 2 Monday, January 12, 2009 12:43 PM
Aim and Scan
3
012345
012345
65°
65°
2
QuickScan
®
i
2983.book Page 3 Monday, January 12, 2009 12:43 PM
Parts of the Imager
Parts of the Imager
LED
Scan
Window
Trigger
Nose
Boot
Scanning Modes
The imager can operate in one of several scanning modes:
Trigger Single — When the trigger is pulled, scanning is activated
until one of the following occurs:
- a programmable duration1 has elapsed
- a label has been read
- the trigger is released
This mode is associated with typical handheld reader operation:
when the trigger is pulled, scanning starts and the product scans
until the trigger is released, or a label is read, or the maximum
programmable duration1 has elapsed.
Trigger Hold Multiple — When the trigger is pulled, scanning starts
and the product scans until the trigger is released or a programmable duration1 has elapsed. Reading a label does not disable
scanning. Double Read Timeout2 prevents undesired multiple
reads while in this mode.
Trigger Pulse Multiple — When the trigger is pulled and released,
scanning is activated until programmable duration1 has elapsed
or the trigger has been pulled again to transition to another
state. Double Read Timeout2 prevents undesired multiple
reads while in this mode.
Flashing — The reader flashes3 on and off regardless of the trigger
status.
1.
2.
3.
See the Product Reference Guide (PRG) for additional programmable
features, in this case: Scanning Active Time.
Double Read Timeout is also programmed using the PRG.
Controlled by Flash On Time and Flash Off Time. Use the PRG to program these options.
Quick Reference Guide3
2983.book Page 4 Monday, January 12, 2009 12:43 PM
Always On — No trigger pull is required to read a barcode. Scanning
is continually on. If the trigger is pulled, the reader acts as if it
is in Trigger Single Mode. Double Read Timeout1 prevents
undesired multiple reads while in this mode.
Stand Mode — No trigger pull is required to read a bar code. Scan-
ning is turned on automatically when an item is placed in reader’s field of view. If the trigger is pulled, the reader acts as if it
in Trigger Single mode. Double Read Timeout2 prevents undesired multiple reads while in this mode.
Trigger Object Sense — This mode is similar to Stand Mode, ex-
cept that a trigger pull is required to activate the decoder.
Scan Mode = Trigger Single
Scan Mode = Trigger Hold Multiple
Scan Mode = Trigger Pulse Multiple
1.
2.
4
Double Read Timeout is programmed using the PRG.
Double Read Timeout is programmed using the PRG.
QuickScan
®
i
2983.book Page 5 Monday, January 12, 2009 12:43 PM
Scanning Modes
Scanning Modes — continued
Scan Mode = Flashing
Scan Mode = Always On
Scan Mode = Stand Mode
Scan Mode = Trigger Object Sense
Quick Reference Guide5
2983.book Page 6 Monday, January 12, 2009 12:43 PM
Troubleshooting
Problem
Possible Cause
Nothing happens when
the scan button is
pulled.
Possible Solutions
No power to the
imager.
Check system power.
Ensure power supply is
connected.
Interface or power
cables are loose.
Ensure all cable connections are secure.
Imager not proLED comes on, but bargrammed for correct
code does not decode.
barcode type.
Ensure imager is programmed to read the type
of barcode scanned. Refer
to the Product Reference
Guide (PRG) for more
information.
Barcode label is
unreadable.
Check the label to ensure
it is not defaced. Try scanning another barcode
type.
Distance between
imager and barcode
is incorrect.
Move imager closer to or
further from the barcode.
Barcode reading ability
has degraded.
Scan Window has
become scratched or
contaminated with
dust.
Replace window as
instructed in this guide.
Barcode is decoded but
not transmitted to the
host.
Imager not programmed for the correct host type.
Scan the appropriate host
type barcode. Refer to the
Product Reference Guide
(PRG) for more information.
For detailed troubleshooting, refer
to the Product Reference Guide.
NOTE
6
QuickScan
®
i
2983.book Page 7 Monday, January 12, 2009 12:43 PM
LED and Beeper Indications
LED and Beeper Indications
The imager’s beeper sounds and its LED illuminates to indicate
various functions or errors on the reader. A “Green Spot” also
lights to indicate a good read. The tables below list these indications. One exception to the behaviors listed in the tables is
that the reader’s functions are programmable, and may or may
not be turned on. For example, certain indications, such as the
power-up beep can be disabled using programming barcode labels. Reference the PRG for a more detailed list.
Indication
LED
Beeper
Power-up
LED flashes/blinks on
power-up, however, this may
be too rapid to view. With a
USB interface, the LED
blinks until enumeration with
the host is completed.
Imager beeps four times
at highest frequency and
volume upon power-up.
Good Read
One beep at current freLED behavior for this indica- quency, volume,
tion is configurable using the mono/bi-tonal setting and
duration upon a successPRG.
ful label scan.
ROM Failure
200ms on / 200ms off
Limited Scanning
Label Read
N/A
Imager Disabled
The LED blinks continuously
100mS on / 900 mS off
Quick Reference Guide7
Imager sounds one error
beep at highest volume
for 200 mS.
Imager 'chirps' six times
at the highest frequency
and current volume.
N/A
2983.book Page 8 Monday, January 12, 2009 12:43 PM
Programming Barcodes
For your convenience, this guide includes the programming
barcodes required to configure the imager for use with different
interface (terminal/host) types.
See the Product Reference Guide (PRG) for more complete information about programming and configurable features. You
can download the latest version of the PRG and any other available publications for the imager from the website listed on the
back cover of this manual.
Resetting the Standard Product Defaults
If you aren’t sure what programming options are in your imager, or you’ve changed some options and want the factory settings restored, scan the Factory Default Settings barcode below.
This will copy the factory configuration for the currently active
interface to the current configuration.
Factory Default Settings
Host Interfaces
Cables may vary depending upon system configuration.
NOTE
8
Some interfaces require the imager to
start in the disabled state when powered on. If additional imager configuration is desired while in this state, pull
the trigger and hold it for five seconds.
The imager will change to a state that
allows programming with barcodes.
QuickScan
®
i
2983.book Page 9 Monday, January 12, 2009 12:43 PM
Programming Barcodes
RS-232 Interface
To use an RS-232 interface, scan the barcode for the desired
RS-232 host type.
Select RS-232 Standard
Select RS-232 Wincor Nixdorf
Select RS-232 OPOS (for use with OPOS/UPOS/JavaPOS)
IBM Interface
Select IBM Port 5B
Select IBM Port 9B
Quick Reference Guide9
2983.book Page 10 Monday, January 12, 2009 12:43 PM
USB Interface
The imager attaches directly to a USB host, or a powered USB
hub, and is powered by it. No additional power supply is required. When using a USB interface, the imager auto-detects
the USB and defaults to the HID keyboard interface.
Select USB-COM-STD1 (simulates RS-232 standard interface)
Select USB Keyboard (with standard key encoding)
Select USB Alternate Keyboard (with alternate key encoding)
Select USB OEM
Select USB-KBD-APPLE (for Apple computers)
1.
10
Download the correct USB Com driver from www.datalogic.com.
QuickScan
®
i
2983.book Page 11 Monday, January 12, 2009 12:43 PM
Programming Barcodes
Keyboard Wedge Interface
To use a Keyboard Wedge interface, scan the barcode for the
desired keyboard type.
Select KBD-AT
(AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95
w/Standard Key Encoding)
Select KBD-AT-NK
(IBM AT PS2 with standard key encoding but without external kbd.)
Select KBD-AT-ALT
(AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95
w/Alternate Key)
Select KBD-AT-ALT-NK (for IBM AT PS2 with alternate key
encoding but without external keyboard)
Quick Reference Guide11
2983.book Page 12 Monday, January 12, 2009 12:43 PM
Keyboard Wedge Interface — continued
Select KBD-XT (PC/XT w/Standard Key Encoding)
Select KBD-IBM-3153 (for IBM Terminal 3153)
Select KBD-IBM-M
(for IBM Terminals 31xx, 32xx, 34xx, 37xx make only keyboard)
Select KBD-IBM-MB
(for IBM Terminals 31xx, 32xx, 34xx, 37xx make break keyboard)
Select KBD-DIG-VT
(for DIGITAL Terminals VT2xx, VT3xx, VT4xx)
12
QuickScan
®
i
2983.book Page 13 Monday, January 12, 2009 12:43 PM
Ergonomic Recommendations
Ergonomic Recommendations
In order to avoid or minimize the
potential risk of ergonomic injury follow the recommendations below.
Consult with your local Health &
CAUTION Safety Manager to ensure that you
are adhering to your company’s
safety programs to prevent employee
injury.
•
•
•
•
•
•
•
•
•
•
•
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment
Improve work procedures.
Regulatory Information
All models are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
Any changes or modifications to equipment, not expressly approved by Datalogic could void the user's authority to operate
the equipment.
Power Supply
Use only a power supply approved by Datalogic for this product and model. Models require either a Listed class II or class
III with a Limited Power Source(LPS) which supplies power directly to the imager. For the safety certification to be valid, class
III input power sources must be IEC/EN60950-1 (EN
60335-series, EN 60065 or relevant) approved.
Input: 100 - 240 VACOutput: 5.2 VDC
Max Current: 0.4 AmpsPower: 15 Watts
For USB Power Off Terminal applications, attach to USB 1.0, 1.1 or
2.0 host device only.
NOTE
Quick Reference Guide
13
2983.book Page 14 Monday, January 12, 2009 12:43 PM
Hinweis
Benutzen Sie nur eine von Datalogic genehmigte Stromversorgung. Die Modelle erfordern eine Stromquelle der Klasse II
oder III mit einer Leistungsbegrenzung (LPS). Für eine gültige
Sicherheitszertifizierung müssen Klasse III Stromquellen am
Eingang nach den Bestimmungen IEC/EN60950-1 (EN
60335-Serien, EN 60065 oder entsprechenden) zugelassen
sein.
Eingang: 100 - 240 VACAusgang: 5.2 VDC
Max. Strom: 0.4 AmpsMax. Leistung: 15 W
Radio Frequency Interference Requirements
This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However there is no guarantee
that interference will not occur in a particular installation. If the
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Tested to comply
with FCC Standards
FOR HOME OR OFFICE USE
The user is cautioned that changes
or modifications not expressly
approved by the party responsible
for compliance could void the
CAUTION user’s authority to operate the
equipment.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
14
QuickScan
®
i
2983.book Page 15 Monday, January 12, 2009 12:43 PM
Replacing the Scan Window
Replacing the Scan Window
If the Scan Window becomes scratched, broken or contaminated with heavy dust, fix it by removing the Nose Boot and cleaning or installing a new window. Datalogic offers a replacement
window as an orderable accessory.
Nose Boot
Scan Window
To replace the Scan Window, first remove power from the imager then hold the imager with the Scan Window facing up.
Gently pull off the Nose Boot and tilt the imager to one side to
remove the window.
Proceed to the next step immediately. DO NOT leave the interior of
the imager exposed.
CAUTION
Holding it by its edges, carefully place the clean replacement
Scan Window in position and secure it in place by reinstalling
the Nose Boot.
Quick Reference Guide
15
2983.book Page 16 Monday, January 12, 2009 12:43 PM
Imager Labeling
Labels are shown here to illustrate their location only. Please
view the labels on your product for actual details.
S/N
Laser &
Regulatory
Regulatory &
Serial Number
FOR LASER VERSION: COMPLIES WITH 21 CFR
1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS
PURSUANT TO LASER NOTICE NO. 50 DATED
JUNE 24, 2007. IEC/EN60825-1:2007. SEE QRG FOR
PATENT INFO.
N263
Waste Electrical and Electronic Equipment (WEEE) Statement
English
For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website
at www.scanning.datalogic.com.
Italian
Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web
www.scanning.datalogic.com.
French
Pour toute information relative à l’élimination des déchets électroniques (WEEE), veuillez consulter le site internet
www.scanning.datalogic.com.
German
Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE) erhalten Sie auf der Webseite
www.scanning.datalogic.com.
Spanish
Si desea información acerca de los procedimientos para el desecho de los residuos del equipo eléctrico y electrónico
(WEEE), visite la página Web www.scanning.datalogic.com.
Portuguese
Para informações sobre a disposição de Sucatagem de Equipamentos Elétricos e Eletrônicos (WEEE -Waste
Electrical and Electronic Equipment), consultar o site web www.scanning.datalogic.com.
Chinese
Japanese
廃電気電子機器 (WEEE) の処理についての関連事項は Datalogic のサイト
www.scanning.datalogic.com をご参照下さい。
16
QuickScan
®
i
2983.book Page 17 Monday, January 12, 2009 12:43 PM
Imager Labeling
Warranty
Datalogic warrants to Customer that Datalogic's products will be free from defects in materials and workmanship
for a period of 5 years from product shipment. In order to obtain service under this Warranty, Customer must
notify Datalogic of the claimed defect before the expiration of the Warranty period and obtain from Datalogic a
return authorization number for return of the product to designated Datalogic service center. If Datalogic determines Customer’s claim is valid, Datalogic will repair or replace product without additional charge for parts and
labor. Customer shall be responsible for packaging and shipping the product to the designated Datalogic service
center, with shipping charges prepaid. Datalogic shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Datalogic service center is located. Customer shall be
responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any
other locations.
Warranty is subject to the limitations and exclusions set forth in the paragraphs that follow.
WARRANTY SET FORTH ABOVE IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING MERCHANTABILITY AND FITNESS.
Exclusions
Warranty coverage shall not apply to any claimed defect, failure or damage which Datalogic determines was
caused by: improper use of product; failure to provide product maintenance, including but not limited to cleaning
of the upper window in accordance with product manual; installation or service of product by other than Datalogic
representatives; use of product with any other instrument, equipment or apparatus; modification or alteration of
product. External cables and replacement of upper window/cartridge due to scratching, stains or other degradation will not be covered under the Warranty. External power supplies returned for service must be accompanied
by the original product for performance of service.
Limitation of Liability
Datalogic's REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCT AS SET FORTH ABOVE IS THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY ON ACCOUNT OF CLAIMS OF BREACH OF WARRANTY OR
PRODUCT DEFECT. UNDER NO CIRCUMSTANCES WILL Datalogic BE LIABLE TO CUSTOMER OR ANY
THIRD PARTY FOR ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL
OR CONTINGENT DAMAGES REGARDLESS OF WHETHER Datalogic HAD ADVANCE NOTICE OF THE
POSSIBILITY OF SUCH DAMAGES.
Assignment
Customer may not assign or otherwise transfer its rights or obligations under Warranty except to a purchaser or
transferee of product. No attempted assignment or transfer in violation of this provision shall be valid or binding
upon Datalogic.
Risk of Loss
Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic shall assume risk of loss
or damage for product in Datalogic's possession or product being returned to Customer by Datalogic, except
such loss or damage as may be caused by the negligence of Customer, its agents or employees. In the absence
of specific written instructions for the return of product to Customer, Datalogic will select the carrier, but Datalogic
shall not thereby assume any liability in connection with the return shipment.
Quick Reference Guide
17
2983.book Page 18 Monday, January 12, 2009 12:43 PM
NOTES
18
QuickScan
®
i
2983.book Page 1 Monday, January 12, 2009 12:43 PM
EUROPEAN DECLARATION OF CONFORMITY
Datalogic Scanning, Inc. hereby declares that the apparatus specified
below has been tested and found compliant to the following European
Council Directives and Harmonized Standards:
Apparatus: QuickScan i: Model QD2100
Directives:
EMC 2004/108/EC
Low Voltage 2006/95/EC
RoHS 2002/95/EC
WEEE 2002/96/EC
Standards:
EN 55022:2006
CISPR 22:2007
AN/NZS CISPR22:2008
EN 55024:1998+A1:2001+A2:2003
IEC 60950-1:2007
EN 61000-3-2:2006
EN 61000-3-3:1995+A1:2001+A2:2005
EN 61000-4-3:2002
Equipment Type:
Interface Protocol:
Placed into EU Service:
Responsible Manufacturer:
Generic Emissions
Generic Emissions
Generic Emissions
Generic Immunity – ITE
(Includes EN610004-2 (ESD), 4-4 (EFT),
4-5 (Surge),
4-6 (Cond Immunity) and
4-11 (Voltage dips/interruptions)
ITE Safety
Harmonic Current
Voltage Fluctuation/Flicker
Radiated RF Immunity
(Susceptibility)
Handheld Barcode Scanning Equipment
RS-232, USB, Keyboard Wedge, IBM
November 2008 under the Datalogic logo
Datalogic Scanning, Inc.
959 Terry St.
Eugene, Oregon USA
Brad West
October 24, 2008
Vice President
Supply Chain Operations
Datalogic Scanning, Inc.
2983.book Page 2 Monday, January 12, 2009 12:43 PM
Australia
Japan
Datalogic Scanning Pty Ltd
Telephone: [61] (2) 9870 3200
australia.scanning@datalogic.com
Datalogic Scanning KK
Telephone: 81 (0)3 3491 6761
japan.scanning@datalogic.com
France and Benelux
Latin America
Datalogic Scanning Sarl
Telephone: [33].01.64.86.71.00
france.scanning@datalogic.com
Datalogic Scanning, Inc
Telephone: (305) 591-3222
latinamerica.scanning@datalogic.com
Germany
Singapore
Datalogic Scanning GmbH
Telephone: 49 (0) 61 51/93 58-0
germany.scanning@datalogic.com
Datalogic Scanning Singapore PTE LTD
Telephone: (65) 6435-1311
singapore.scanning@datalogic.com
India
Spain and Portugal
Datalogic Scanning India
Telephone: 91- 22 - 64504739
india.scanning@datalogic.com
Datalogic Scanning Sarl Sucursal en España
Telephone: 34 91 746 28 60
spain.scanning@datalogic.com
Italy
United Kingdom
Datalogic Scanning SpA
Telephone: [39] (0) 39/62903.1
italy.scanning@datalogic.com
Datalogic Scanning LTD
Telephone: 44 (0) 1923 809500
uk.scanning@datalogic.com
www.scanning.datalogic.com
Datalogic Scanning, Inc.
959 Terry Street
Eugene, OR 97402
USA
Telephone: (541) 683-5700
Fax: (541) 345-7140
© 2008 - 2009 Datalogic Scanning, Inc.
R44-2983 (Rev. A)
1/09