Casio CE-6000 User`s manual

ELECTRONIC CASH REGISTER
TK-6000/6500
6~00
E
L
P
AP
PIE
E
E
F
F
O
C
6%00
H
C
N
E
R
F
D
E
I
FR
H
C
I
W
D
N
SA
M
A
E
R
C
ICE
Eu
Di
U.K.
CI
Canada
USER'S MANUAL
Introduction & Contents
Introduction
Congratulations on your selection of a CASIO TK-6000/TK-6500 series electronic cash register. This ECR is
the product of the world's most advanced electronic technology, for outstanding versatility and reliability.
Simplified operation is made possible by a specially designed keyboard layout and a wide selection of
automated, programmable functions.
A specially designed keyboard layout and a bright, easy-to-read display help to take the fatigue out of long
hours operation.
Notes for TK-6000-1
Casio Electronics Co., Ltd.
Unit 6, 1000 North Circular Road
London NW2 7JD, U.K.
Please keep all information for future reference.
Notes for TK-6000/6500
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A.
(Not applicable to other areas)
WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of Canadian Department of Communications.
The main plug on this equipment must be used to disconnect mains power.
Please ensure that the socket outlet is installed near the equipment and shall be easily
accessible.
2
Important!
Introduction & Contents
Your new cash register has been carefully tested before shipment to ensure proper operation.
Safety devices eliminate worries about breakdowns resulting from operator errors or improper handling. In order to ensure years of trouble-free operation, however, the following points should be
noted when handling the cash register.
Do not locate the cash register where it will be
subjected to direct sunlight, high humidity,
splashing with water or other liquids, or high
temperature (such as near a heater).
Be sure to check the sticker on the side of the
cash register to make sure that its voltage
matches that of the power supply in the area.
Never operate the cash register while your
hands are wet.
Use a soft, dry cloth to clean the exterior of the
cash register. Never use benzene, thinner, or
any other volatile agent.
Never try to open the cash register or attempt
your own repairs. Take the cash register to your
authorized CASIO dealer for repairs.
TK-6000/6500 User's Manual
3
Introduction & Contents
Introduction & Contents ............................................................................................................ 2
Getting Started ........................................................................................................................... 8
Remove the cash register from its box. .................................................................................................. 8
Remove the tape holding parts of the cash register in place. ................................................................ 8
Remove the cash drawer from its box. ................................................................................................... 8
Connect the drawer. ............................................................................................................................... 8
Mount the cash register. ......................................................................................................................... 9
Plug the cash register into a wall outlet. ................................................................................................. 9
Insert the mode key marked “OW” into the mode switch. ...................................................................... 9
Install receipt/journal paper. .................................................................................................................10
Set the date. ......................................................................................................................................... 12
Set the time. ..........................................................................................................................................12
Introducing TK-6000/6500 ....................................................................................................... 14
General guide .......................................................................................................................................14
Display (TK-6000/TK-6500) ..................................................................................................................18
Keyboard (TK-6000) ............................................................................................................................. 20
Keyboard (TK-6500) ............................................................................................................................. 22
Allocatable functions ............................................................................................................................. 24
How to remove/replace the sheet holder (TK-6000 only) .................................................................... 26
How to install a menu sheet in the sheet holder (TK-6000 only) ......................................................... 27
Basic Operations and Setups ................................................................................................. 28
How to read the printouts ............................................................................................................... 28
How to use your cash register ........................................................................................................ 29
Assigning a clerk .................................................................................................................................. 30
Clerk button ................................................................................................................................. 30
Clerk lock/clerk key ...................................................................................................................... 30
Clerk secret number key ............................................................................................................. 30
Displaying the time and date ................................................................................................................ 31
Preparing coins for change ..................................................................................................................31
Preparing and using department/flat-PLU keys ............................................................................. 32
Registering department/flat-PLU keys.................................................................................................. 32
Programming department/flat-PLU keys .............................................................................................. 33
To program a unit price for each department/flat-PLU ................................................................ 33
To program the tax calculation status for each department/flat-PLU .......................................... 33
To program high amount limit for each department/flat-PLU ...................................................... 34
Registering department/flat-PLU keys by programming data .............................................................. 35
Preset price ................................................................................................................................. 35
Preset tax status .......................................................................................................................... 35
Locking out high amount limitation .............................................................................................. 35
Preparing and using PLUs ............................................................................................................. 36
Programming PLUs ..............................................................................................................................36
To program a unit price for each PLU ......................................................................................... 36
To program tax calculation status for each PLU ......................................................................... 36
Registering PLUs .................................................................................................................................. 37
Shifting the taxable status of an item ............................................................................................. 39
Calculation merchandise subtotal ........................................................................................................ 39
Preparing and using discounts ....................................................................................................... 40
Programming discounts ........................................................................................................................40
Registering discounts ........................................................................................................................... 40
Discount for items and subtotals ................................................................................................. 40
4
Preparing and using reductions ..................................................................................................... 41
Introduction & Contents
Programming for reductions .................................................................................................................41
To program preset reduction amount .......................................................................................... 41
Registering reductions .......................................................................................................................... 41
Reduction for items ...................................................................................................................... 41
Reduction for subtotal ................................................................................................................. 42
Registering credit and check payments ......................................................................................... 43
Check ........................................................................................................................................... 43
Credit ........................................................................................................................................... 43
Mixed tender (cash, credit and check) ........................................................................................ 43
Preparing and registering the Euro ................................................................................................ 44
Basic programming for the Euro and its exchange rate ....................................................................... 44
Registering the Euro ............................................................................................................................. 44
Validation printing ........................................................................................................................... 46
Total amount validation ................................................................................................................ 46
Validation sample ........................................................................................................................ 46
Registering returned goods in the REG mode ............................................................................... 47
Registering returned goods in the RF mode .................................................................................. 47
Normal refund transaction .................................................................................................................... 47
Reduction of amounts paid on refund .................................................................................................. 48
Registering money received on account ........................................................................................
Registering money paid out ...........................................................................................................
Registering loan amounts ..............................................................................................................
Registering pick up amounts ..........................................................................................................
Changing media in drawer .............................................................................................................
Making corrections in a registration ...............................................................................................
48
48
49
49
49
50
To correct an item you input but not yet registered .............................................................................. 50
To correct an item you input and registered ......................................................................................... 51
To cancel all items in a transaction....................................................................................................... 52
No sale registration ........................................................................................................................ 52
Printing the daily sales reset report ................................................................................................ 53
Advanced Operations .............................................................................................................. 54
Clerk interrupt function ................................................................................................................... 54
Single item cash sales.................................................................................................................... 55
Addition .......................................................................................................................................... 56
Addition (plus) ....................................................................................................................................... 56
Premium (%+) ....................................................................................................................................... 56
Tray total ......................................................................................................................................... 57
Tray total premium/discount .................................................................................................................57
Multiple item totalling function .............................................................................................................. 57
Coupon transactions ...................................................................................................................... 58
Coupon registration using <COUPON> (coupon key) ......................................................................... 58
Coupon registration using <COUPON2> (coupon 2 key) .................................................................... 58
Preset tender amount ..................................................................................................................... 59
Bottle link operation ........................................................................................................................ 60
Bottle returns ........................................................................................................................................ 60
Bottle return key .......................................................................................................................... 60
Arrangement key registrations ....................................................................................................... 61
Set menu ........................................................................................................................................ 61
TK-6000/6500 User's Manual
5
Introduction & Contents
Currency exchange function .......................................................................................................... 62
Registering foreign currency ................................................................................................................ 62
Full amount tender in foreign currency ........................................................................................ 62
Partial tender in a foreign currency ............................................................................................. 63
Food stamp function ....................................................................................................................... 64
Food stamp registration ........................................................................................................................64
No change due ............................................................................................................................ 64
Mixed food stamp/cash change ................................................................................................... 65
Food stamp registration (Illinois rule) ................................................................................................... 67
No change due ............................................................................................................................ 67
Mixed food stamp/cash change ................................................................................................... 69
Electronic benefits transfer ...................................................................................................................73
About mixed EBT card tenders ................................................................................................... 73
No change due ............................................................................................................................ 73
Tips .................................................................................................................................................
Inputting the number of customers .................................................................................................
Text recall .......................................................................................................................................
Temporarily releasing compulsion ..................................................................................................
Printing slip .....................................................................................................................................
74
75
76
76
77
Printing slips ......................................................................................................................................... 77
To perform auto batch printing 1 .................................................................................................. 78
To perform auto batch printing 2 .................................................................................................. 78
About the maximum number of slip lines .................................................................................... 78
Check tracking systems ................................................................................................................. 78
Check tracking system .........................................................................................................................78
Opening a check .......................................................................................................................... 79
Adding to a check ........................................................................................................................ 79
Issuing a guest receipt ................................................................................................................ 80
Closing a check memory ............................................................................................................. 80
New/old check key operation ...................................................................................................... 81
Add check .................................................................................................................................... 82
Separate check ............................................................................................................................ 83
Clerk transfer ............................................................................................................................... 84
Table transfer ............................................................................................................................... 84
VAT breakdown printing.................................................................................................................. 85
Deposit registrations....................................................................................................................... 85
Deposit from customer ................................................................................................................ 85
Deposit from customer during sales transaction ......................................................................... 85
Bill copy .......................................................................................................................................... 86
Programming to clerk ..................................................................................................................... 87
Programming clerk number ..................................................................................................................87
Programming trainee status .................................................................................................................87
Programming commission rate .............................................................................................................87
Programming descriptors and messages ....................................................................................... 88
Programming receipt message and clerk name ...................................................................................88
Machine number .......................................................................................................................... 88
Programming department/transaction key descriptor .......................................................................... 90
Programming flat-PLU descriptor ......................................................................................................... 91
Entering characters ........................................................................................................................ 92
Entering characters by code .................................................................................................................92
Character code list ....................................................................................................................... 92
Using character keyboard..................................................................................................................... 93
6
Printing read/reset reports .............................................................................................................. 94
Introduction & Contents
To print the individual department, PLU/flat-PLU read report .............................................................. 94
To print the financial read report ...........................................................................................................95
To print the individual clerk read/reset report ....................................................................................... 95
To print the daily sales read/reset report .............................................................................................. 96
To print the PLU/flat-PLU read/reset report .......................................................................................... 98
To print the hourly sales read/reset report ............................................................................................ 98
To print the monthly sales read/reset report ......................................................................................... 99
To print the group read/reset report ...................................................................................................... 99
To print the periodic 1/2 sales read/reset reports ...............................................................................100
To print other sales read/reset reports ...............................................................................................101
Reading the cash register's program ........................................................................................... 101
To print unit price/rate program (except PLU/flat-PLU) ...................................................................... 101
To print key descriptor, name, message program (except PLU) ........................................................ 102
To print the PLU/flat-PLU program .....................................................................................................103
Troubleshooting ..................................................................................................................... 104
When an error occurs ...................................................................................................................
In case of power failure ................................................................................................................
Clearing a machine lock up ..........................................................................................................
When the register does not operate at all ....................................................................................
104
105
106
106
User Maintenance and Options ............................................................................................ 107
To replace the ink ribbon ..............................................................................................................
To replace journal paper ...............................................................................................................
To replace receipt paper ...............................................................................................................
To replenish the stamp ink ...........................................................................................................
Options .........................................................................................................................................
107
108
109
109
109
Specifications ......................................................................................................................... 110
Index ......................................................................................................................................... 111
TK-6000/6500 User's Manual
7
Getting Started
This section outlines how to unpack the cash register and get it ready to operate. You should read this part of
the manual even if you have used a cash register before. The following is the basic set up procedure, along with
page references where you should look for more details.
1.
Remove the cash register from its box.
2.
3.
4.
Also remove the small plastic bag taped to
the printer cover. Inside you will find the
mode keys.
Remove the cash drawer from its box.
The cash register and cash drawer are packed separately.
Connect the drawer.
1. Connect drawer connector (three color lead on
drawer) to the cash register.
2. Connect frame drawer connector (green lead on
drawer) to the cash register.
8
Remove the tape holding parts
of the cash register in place.
5.
Mount the cash register.
6.
Getting Started
1. Screw in 2 fixing screws bottom side of the
register.
2. Mount the cash register on the top of the
drawer, ensuring that the feet on the bottom of
the cash register go into the holes on the
drawer.
Plug the cash register into a wall
outlet.
Be sure to check the sticker on the side of the cash
register to make sure that its voltage matches that of
the power supply in your area. The printer will
operate for a few seconds. Please do not pass the
power cable under the drawer.
7.
Insert the mode key marked
“OW” into the mode switch.
REG2
REG1
OFF
CA3
2
X1
Z1
X2/Z2
RF
PGM
TK-6000/6500 User’s Manual
9
Getting Started
8.
Install receipt/journal paper.
Loading journal paper
The same type of paper (45 mm × 83 mm i.d.) is used for receipts and journal. Load the new paper
before first operating the cash register or when red paper appears from the printer.
REG2 X1
REG1
Z1
OFF
X2/Z2
RF
1
Use a mode key to set the
mode switch to REG1
position.
PGM
2
Open the printer cover
using the printer cover
key.
3
Drop the paper roll gently
and insert paper to the
paper inlet.
6
Cut off the leading end of
the paper so it is even.
Press the j key until
about 20 cm to 30 cm of
paper is fed from the
printer.
4
7
Ensuring the paper is
being fed from the bottom
of the roll, lower the roll
into the space behind the
printer.
10
5
Slide the leading end of
the paper into the groove
on the spindle of the takeup reel and wind it onto
the reel two or three turns.
Loading receipt paper
through
3
under “Loading journal paper” on the
4
Ensuring the paper is
being fed from the
bottom of the roll, lower
the roll into the space
behind the printer.
8
Place the take-up reel into
place behind the printer,
above the roll paper.
9
Press the j key to take
up any slack in the paper.
5
Drop the paper roll gently
and insert paper to the
paper inlet.
6
Press the f key until
about 20 cm to 30 cm of
paper is fed from the
printer.
0
Close the printer cover.
7
Set the printer cover,
passing the leading end of
the paper through the
paper outlet. Close the
printer cover and tear off
the excess paper.
Important!
Never operate the cash register without paper. It can damage the printer.
TK-6000/6500 User’s Manual
11
Getting Started
1
Follow steps
previous page.
Getting Started
9.
Set the date.
REG2
X1
REG1
Z1
OFF
X2/Z2
6 1s 6 : : : : : : 6
RF
Current date
PGM
Year
X1
REG1
Z1
X2/Z2
Month
6 1s 6 : : : : 6
Current time
RF
PGM
Mode Switch
x
or
X
Example:
08:20 AM 2 0820
09:45 PM 2 2145
(24-hour military time)
12
6C
X
Day
Set the time.
REG2
OFF
or
Example:
April 3, 2000 2 000403
Mode Switch
10.
x
6C
Getting Started
TK-6000/6500 User’s Manual
13
Introducing TK-6000/6500
General guide
This part of the manual introduces you to the cash register and provides a general explanation of its various
parts.
Pop-up display
Main display
Mode switch
Keyboard
Menu sheet holder
Take-up reel
Roll paper
Printer
Printer ink ribbon
Drawer
Drawer lock
Printer sub cover
Printer cover
Printer cover key
Roll paper
TK-6000
(with slit drawer)
Receipt on/off switch
You can use the roll paper to print receipts and a
journal (pages 10 ~ 11).
Printer ink ribbon
Indicator
RECEIPT
ON/OFF
Provides ink for printing of registration details on the
roll paper (page 107).
Receipt on/off key
Receipt on/off switch / key
Use the receipt on/off switch/key in REG1, REG2 and
RF modes to control issuance of receipts. In other
modes, receipts or reports are printed regardless the
receipt switch/key setting.
A post-finalization receipt can still be issued after
finalization when the switch/key is set to off. The cash
register can also be programmed to issue a post-finalization receipt even when the switch/key is set to on.
14
8(
RECEIPT
ON/OFF
RCT
Indicator
When the register issues receipts, this indicator is lit.
Pop-up display
Main display
Mode switch
Take-up reel
Roll paper
Printer
Keyboard
Drawer
Drawer lock
Printer sub cover
Printer cover
TK-6500
(with slit drawer)
Printer cover key
Mode key (for U.K., U.S. and Canada)
Mode key (for other area)
The following four types of mode keys are provided
with the unit in the United Kingdom, the United States
and Canada.
The following three types of mode keys are provided
with the unit in areas outside of the United Kingdom,
the United States and Canada.
OP
C-A02
M
C-A08
OW
C-A08
PGM
C-A32
a. OP (Operator) key
Switches between OFF and REG1.
b. M (Master) key
Switches between OFF, REG1, REG2, X1 and RF.
c. OW (Owner) key
Switches between OFF, REG1, REG2, X1, Z1, X2/
Z2 and RF.
d. PGM (Program) key
Switches to any position.
TK-6000/6500 User’s Manual
OP
C-A02
M
OW
C-A08
C-A32
a. OP (Operator) key
Switches between OFF and REG1.
b. M (Master) key
Switches between OFF, REG1, REG2, X1 and RF.
c. OW (Owner) key
Switches to any position.
15
Introducing TK-6000/6500
Wetproof cover
Printer ink ribbon
Introducing TK-6000/6500
Mode switch
Use the mode keys to change the position of the mode
switch and select the mode you want to use.
REG2
REG1
OFF
X1
Z1
X2/Z2
RF
PGM
Mode
Mode name
switch
Description
OFF
Stand-by
Any of the mode control keys can be inserted and
removed from the mode switch in this position.
REG1
Register 1
Used for normal sales transactions. Any of the mode
control keys can be inserted and removed from the mode
switch in this position.
REG2
Register 2
Used for special operations. Since switching to REG2
requires a special key, such functions as discounts, credit
sales, charge sales, check payments, and paid outs can be
controlled by programming them as prohibited in REG1
and allowed in REG2.
RF
Refund
Reg minus
Used for processing refunds.
When the mode switch of the register is in RF position,
you can access either the refund mode or the register
minus mode.
X1
Daily sales
read
Used to obtain daily reports without resetting (clearing)
all total data.
Z1
Daily sales
reset
Used to obtain daily reports while resetting (clearing) all
total data.
X2/Z2
PGM
Periodic sale Used to obtain periodic sales reports without resetting
read/reset total data or while resetting all total data.
Program
Used when programming functions and preset data such
as unit prices and tax rates. Also used when reading
program data.
Clerk key/button/lock
On models available in the United States and Canada,
clerk or cashier assignment can be performed using
clerk secret numbers only (clerk buttons are not
equipped).
In Germany, you can assign clerks by using clerk key
or by clerk secret number (clerk key is equipped).
In other areas, you can assign clerks by using clerk
button or by clerk secret number.
The method you are assigning clerk depends on the
programming of your cash register.
16
Clerk secret number key
Clerk button
When the cash register is programmed to use clerk
secret numbers for clerk or cashier assignment, the
clerk buttons are not functional.
You can assign the clerk or cashier using the four
buttons located below the display panel.
CLK1 CLK2 CLK3 CLK4
CLK#
You can assign the clerk or cashier inserting a clerk key
into the clerk lock .
111 1
Clerk lock
Clerk key
Drawer
The drawer opens automatically whenever you finalize
a registration and whenever you issue a read or reset
report. The drawer will not open if it is locked with the
drawer key.
Drawer lock
Use the drawer key to lock and unlock the drawer.
When the cash drawer does not open!
In case of power failure or the machine is in malfunction, the cash drawer does not open automatically. Even
in these cases, you can open the cash drawer by pulling
drawer release lever (see below).
Important!
The drawer will not open, if it is locked with a drawer lock key.
TK-6000/6500 User’s Manual
17
Introducing TK-6000/6500
Clerk lock/key
Introducing TK-6000/6500
Display (TK-6000/TK-6500)
Display panel
Main display for the U.S.
PLU
DEPT
AMOUNT
RPT MENU
01
RCT
REG
Customer display for all area
1"34
X1
Z1
T/S1
T/S2
T/S3
F/S
TOTAL
CHANGE
Main display for Canada and Germany
PLU
DEPT
AMOUNT
RPT MENU
0122
RCT
REG
X1
Z1
"34
1
2
3
4
TOTAL
CHANGE
TAX
Main display for other area
PLU
DEPT
AMOUNT
RPT MENU
12#45
REG
X1
Z1
1
2
3
TAX
18
4
TOTAL
CHANGE
5&78
TOTAL CHANGE
Display example
Item registration
012
RCT
1 Amount/Quantity
AMOUNT
RPT MENU
X1
REG
1"34
Z1
T/S1
T/S2
2 4
T/S3
F/S
3
TOTAL
CHANGE
PLU
3 Taxable sales status indicators
AMOUNT
When you register a taxable item, the corresponding
indicator is lit.
RPT MENU
-2RCT
X1
REG
Z1
1
2
3
4
TOTAL
CHANGE
TAX
Repeat registration
PLU
5 Menu sheet number
MENU key to designate the 1st ~
When you press the B
AMOUNT
RPT MENU
5
X1
REG
!23
Z1
1
2
3
4
TOTAL
CHANGE
6
Totalize operation
PLU
AMOUNT
X1
REG
Z1
T/S1
T/S2
6 Number of repeats
7 Total/Change indicators
RPT MENU
1"34
RCT
6th menu sheet, the corresponding number is displayed.
Anytime you perform a repeat registration (pages
32, 37), the number of repeats appears here.
Note that only one digit is displayed for the number
of repeats. This means that a “5” could mean 5, 15
or even 25 repeats.
TAX
DEPT
4 PLU, flat-PLU number
When you register a PLU, flat-PLU item, the corresponding PLU, flat-PLU number appears here.
5
DEPT
2 Department number
When you press a department key to register a unit
price, the corresponding department number (01 ~
04, 08) appears here.
1
Menu shift
DEPT
This part of the display shows monetary amounts. It
also can be used to show the current date and time.
T/S3
F/S
8
TOTAL
CHANGE
When the TOTAL indicator is lit, the displayed
value is monetary total or subtotal amount. When
the CHANGE indicator is lit, the displayed value is
the change due.
7
8 RCT, REG, X1, Z1 indicators
PLU
DEPT
AMOUNT
RPT MENU
12#45
REG
X1
Z1
1
2
3
4
TOTAL
RCT: When the register issues receipts, this indicator is lit.
X1: Indicates daily sales read mode
Z1: Indicates daily sales reset mode
CHANGE
TAX
8
7
RECEIPT
ON/OFF
TK-6000/6500 User’s Manual
19
Introducing TK-6000/6500
PLU
DEPT
Introducing TK-6000/6500
Keyboard (TK-6000)
1RECEIPT
FEED
JOURNAL
FEED
8 K L
RC
CLK#
PD
T
2 0 A N
RECEIPT
–
4
8
T/S2
3
7
%–
3RECEIPT D E
ON/OFF
T/S1
5 F G#
RF
VALID
C
7
7
4
5
9
6
1
2
3
0
00
•
27
36
45
54
63
72
81
90
99
108
8
17
26
35
44
53
62
71
80
89
98
107
7
16
25
34
43
52
61
70
79
88
97
106
6
15
24
33
42
51
60
69
78
87
96
105
6
1
5
5
14
23
32
41
50
59
68
77
86
95
104
CR1
CR2
4
13
22
31
40
49
58
67
76
85
94
103
P QCHK/
3
12
21
30
39
48
57
66
75
84
93
102
2
11
20
29
38
47
56
65
74
83
92
101
1
10
19
28
37
46
55
64
73
82
91
100
ERR.
CORR
CANCEL
8
18
2
NS
6 H J
X/FOR
DATE
TIME
9
O
CH
TEND
R
SUBTOTAL
SCA
AMT
TEND
for the U.S. and Canada
• Register Mode
1 Paper feed key f, j
Hold this key down to feed paper from the printer.
2 Post receipt key ;
Use this key to produce a post-finalization receipt .
3 Receipt on/off key Q
Use this key pressing two times to change the status
“receipt issue” or “no receipt.” In case of “receipt issue”,
the indicator is lit.
4 Open key O
Use this key to temporarily release a limitation on the
number of digits that can be input for a unit price.
5 Refund key R
Use this key to input refund amounts and void certain
entries.
6 Clear key C
Use this key to clear an entry that has not yet been
registered.
7 Ten key pad 0, 1 ~ 9, -, ^
Use these keys to input numbers.
8 Clerk number key o
Use this key to sign clerk on and off the register.
9 VAT key V
Use this key to print a VAT breakdown.
0 Discount key p
Use this key to register discounts.
A Minus key m
Use this key to input values for subtraction.
20
B Loan key l
This key is used to input the amount of money provided
for making change. This operation affects media totals,
rather than sales totals. Loans are made for all types of
money which can be specified by the finalize key.
C Pick up key L
When the amount in drawer exceeds the limit value
(sentinel function), the manager performs a pick up
operation. This key is used for this function. This
operation affects media totals, rather than sales totals.
Pick ups are made for all types of money which can be
specified by the finalize key.
D Tax status shift 1 key t
Use this key to change the Taxable 1 status of the next
item.
E Tax status shift 2 key T
Use this key to change the Taxable 2 status of the next
item.
F Validation key v
Use this key to validate transaction amounts on slip.
G Non-add/No sale key N
Non-add key: To print reference number (to identify a
personal check, credit card, etc.) during a transaction, use
this key after some numerical entries.
No sale key: Use this key to open the drawer without
registering anything.
FEED
JOURNAL
FEED
9 K MEURO
RC
VAT
2 B CPICK N
RECEIPT
LOAN
ON/OFF
%–
VALID
3
2
NS
6 I J
C
7
X
DATE
TIME
8
9
4
5
6
1
2
3
0
00
•
FEED
JOURNAL
FEED
9 K MEURO
VAT
RC
2 B CPICK N
RECEIPT
LOAN
OPEN
–
5 F G#
RF
4
UP
%–
VALID
T
PD
3
2
NS
6 I J
ERR.
CORR
CANCEL
7
1RECEIPT
4 0 A
–
5 F G#
RF
4
UP
3RECEIPT0 A
T
PD
1
O
7
CR1
CR2
P QCHK/
CH
TEND
R
SUBTOTAL
SCA
C
AMT
TEND
for German
H Multiplication/For/Date/Time key x
Use this key to input a quantity for a multiplication
operation and registration of split sales of packaged
items. Between transactions, this key displays the current
time and date.
I Multiplication/Date/Time key X
Use this key to input a quantity for a multiplication
operation. Between transactions, this key displays the
current time and date.
J Error correction/Cancellation key e
Use this key to correct registration errors and to cancel
registration of entire transactions.
K Received on account key r
Use this key following a numeric entry to register money
received for non-sale transactions.
X
DATE
TIME
ERR.
CORR
CANCEL
7
8
9
4
5
6
1
2
3
0
00
•
1
O
CR1
CR2
P QCHK/
CH
Introducing TK-6000/6500
1RECEIPT
TEND
R
SUBTOTAL
SCA
AMT
TEND
for other area
O Credit key c, d
Use this key to register a credit sale.
P Charge key h
Use this key to register a charge sale.
Q Check key k
Use this key to register a check tender.
R Subtotal key s
Use this key to display and print the current subtotal
(includes add-on tax) amount.
S Cash/Amount tendered key a
Use this key to register a cash tender.
T Flat PLU key (, ) ~ /
Use these keys to register items to flat PLUs.
L Paid out key P
Use this key following a numeric entry to register money
paid out from the drawer.
M Euro/Paid out key q
Euro key: Use this key to convert the main currency to
the sub currency (the euro/the local money), when
registering a subtotal amount. This key is also used for
specifying sub currency while entering an amount of
payment or declaration in drawers.
Paid out key: Use this key following a numeric entry to
register money paid out from the drawer.
N Department keys !, ", # ~ $ ,%
Use these keys to register items to departments.
TK-6000/6500 User’s Manual
21
Introducing TK-6000/6500
Keyboard (TK-6500)
1
2
RECEIPT JOURNAL
FEED FEED
3
4
5
I
RECEIPT VALID CLK#
25
34
43
52
61
70
79
88
97
106
6RECEIPT7
ON/OFF
8
16
24
33
42
51
60
69
78
87
96
105
7
15
23
32
41
50
59
68
77
86
95
104
6
14
22
31
40
49
58
67
76
85
94
103
CORR
CANCEL
5
13
21
30
39
48
57
66
75
84
93
102
C
4
12
20
29
38
47
56
65
74
83
92
101
9
0
H
UP
A
—
BERR. C
E
PD
8PICKK
LOAN
%–
J
RC
RF
D
T/S1
T/S2
FX/FOR G#
DATE
TIME
NS
7
8
9
5
6
3
11
19
28
37
46
55
64
73
82
91
100
4
2
10
18
27
36
45
54
63
72
81
90
99
1
2
3
1
9
17
26
35
44
53
62
71
80
89
98
0
00
•
L
4
8
3
7
2
6
1
5
CR2
CR1
M
N
CHK/
TEND
CH
O
SUBTOTAL
PCA
AMT
TEND
for the U.S.
• Register Mode
1 Paper feed key f, j
Hold this key down to feed paper from the printer.
2 Flat PLU key (, ) ~ .
Use these keys to register items to flat PLUs.
3 Post receipt key ;
Use this key to produce a post-finalization receipt .
4 Validation key v
Use this key to validate transaction amounts on slip.
5 Clerk number key o
Use this key to sign clerk on and off the register.
6 Receipt on/off key Q
Use this key pressing two times to change the status
“receipt issue” or “no receipt.” In case of “receipt issue”,
the indicator is lit.
7 Loan key l
This key is used to input the amount of money provided
for making change. This operation affects media totals,
rather than sales totals. Loans are made for all types of
money which can be specified by the finalize key.
8 Pick up key L
When the amount in drawer exceeds the limit value
(sentinel function), the manager performs a pick up
operation. This key is used for this function. This
operation affects media totals, rather than sales totals.
Pick ups are made for all types of money which can be
specified by the finalize key.
9 Discount key p
Use this key to register discounts.
22
0 Minus key m
Use this key to input values for subtraction.
A Refund key R
Use this key to input refund amounts and void certain
entries.
B Error correction/Cancellation key e
Use this key to correct registration errors and to cancel
registration of entire transactions.
C Tax status shift 1 key t
Use this key to change the Taxable 1 status of the next
item.
D Tax status shift 2 key T
Use this key to change the Taxable 2 status of the next
item.
E Clear key C
Use this key to clear an entry that has not yet been
registered.
F Multiplication/For/Date/Time key x
Use this key to input a quantity for a multiplication
operation and registration of split sales of packaged
items. Between transactions, this key displays the current
time and date.
G Non-add/No sale key N
Non-add key: To print reference number (to identify a
personal check, credit card, etc.) during a transaction, use
this key after some numerical entries.
No sale key: Use this key to open the drawer without
registering anything.
Introducing TK-6000/6500
H Ten key pad 0, 1 ~ 9, -, ^
Use these keys to input numbers.
I Received on account key r
Use this key following a numeric entry to register money
received for non-sale transactions.
J Paid out key P
Use this key following a numeric entry to register money
paid out from the drawer.
K Department keys !, ", # ~ %
Use these keys to register items to departments.
L Credit key c, d
Use this key to register a credit sale.
M Check key k
Use this key to register a check tender.
N Charge key h
Use this key to register a charge sale.
O Subtotal key s
Use this key to display and print the current subtotal
(includes add-on tax) amount.
P Cash/Amount tendered key a
Use this key to register a cash tender.
TK-6000/6500 User’s Manual
23
Introducing TK-6000/6500
Allocatable functions
You can tailor a keyboard to suit your particular type of
business.
Add check
Use this key in a check tracking system to combine the
details of more than one check into a single check.
Arrangement
Use this key to activate an arrangement program programmed in the arrangement file. Any operation that can
be performed from the keyboard, as well as mode, can be
programmed in an arrangement program, and can be
performed merely by pressing this key. In addition, one
numeric entry can be included in an arrangement program. In this case, input the number and press this key.
The mode control function of this key can be programmed for all modes except for the OFF and PGM
mode.
Bill copy
Use this key to issue bill copy.
Bottle return
Use this key to specify next item as bottle return.
Cancel
Invalidates all preceding data registered for departments,
PLUs and set menus within a transaction. This key must
be pressed before the transaction involving the data to be
invalidated is finalized. It is also effective even after
calculation of subtotal amount.
Check endorsement
Use this key to print a preset check endorsement message
using the slip printer.
Check print
Use this key to print the check on the slip printer.
Clerk transfer
Use this key to transfer opened checks to another clerk.
Coupon
Use this key for registering coupons.
Coupon 2
Use this key to declare the next item registration as
coupon.
Cube
This key provides the same functions as the Square key.
In addition, this key also has a cube multiplication
function.
Currency exchange
Use this key to convert foreign currency to local currency
or vice versa using the exchange rate preset for the key
and displays the result.
Use this key for conversions of a home currency subtotal
or merchandise subtotal to equivalent of another
country's currency.
Use this key for conversions of another country's currency to the equivalent of the home currency.
24
Customer number
Use this key to register the number of customers.
Declaration
Use this key to declare in drawer amount for money
declaration.
Deposit
Use this key to register deposits.
Eat-in
Use this key to specify if the customer eats in the restaurant. Before closing a transaction press this key.
EBT (electronic benefit transfer)
Use this key to register an EBT amount with a tender
amount input.
Food stamp shift
Use this key to change food stamp status.
Food stamp subtotal
Use this key to obtain the food stamp applicable amount.
Food stamp tender
Use this key to register a food stamp payment amount
with a tender amount input.
Ketten Bon
Use this key to enter quantities for multiplication.
Multiplication by this key issues singular order prints.
Manual tax
Use this key to register a tax amount.
Menu shift
Use this key to shift key to the 1st ~ 6th menu.
Merchandise subtotal
Use this key to obtain subtotal excluding the add-on tax
amount and the previous balance.
New balance
Use this key for adding the latest registered total amount
to the previous balance to obtain a new balance.
New check
Use this key in a check tracking system to input a new
check number in order to open a new check under that
number.
New/Old check
Use this key in a check tracking system to input check
numbers in order to open new checks and to reopen
existing checks. When the clerk inputs a check number,
the register checks to see if that number already exists in
the check tracking memory. If there is no matching
number in the memory, a new check is opened under the
input number. If the check number input matches a
number already stored in the memory, that check is
reopened for further registration or finalization.
No sale
Use this key to open the drawer between transaction.
Non add
Use this key to print reference numbers (personal check
number, card number, etc.)
Use this key to change the order status from Bon to normal.
Old check
Use this key in a check tracking system to input the
number of an existing check (previously created by the
New check key) whose details are stored in the check
tracking memory. Existing checks are reopened to
perform further registration or to finalize them.
Open 2
Use this key to suspend the compulsory specifications.
Open check
Use this key to issue an open check report of an assigned
clerk.
Operator number
Use this key to enter a clerk number during clerk transfer.
Operator X/Z
Use this key to issue a clerk’s individual X/Z report.
Plus
Use this key for registering surcharge.
Premium
Use this key to apply a preset % or manual input % to
obtain the premium amount for the last registered item or
subtotal.
Previous balance
Use this key to register the previous negative/positive
balance at the beginning of or during a transaction.
Previous balance subtotal
Use this key to obtain subtotal excluding the add-on tax
amount and current balance.
Price
Use this key to register an open PLU.
Price inquiry
Use this key to confirm the price and descriptors of PLU
without registering.
Rate tax
Use this key to activate the preset tax rate or manually
input rate to obtain the tax for the preceding taxable
status 1 amount.
Recall
Use this key for recalling the transferred check number
by the store key. When this key is pressed, the check
number will appear in order of the oldest record.
Review
Use this key to examine the current transaction by
displaying item descriptor and registered amount. This
key is also used for void operation.
Separate check
Use this key in a check tracking system to separate
selected items from one check to another check.
TK-6000/6500 User’s Manual
Slip feed/release
Use this key to feed slips inserted into the slip printer.
This is done by specifying the number of feed lines. This
key is also used to release the slip paper holder if numbers are not entered.
Slip back feed/release
Use this key to back feed slips inserted into the slip
printer. This is done by specifying the number of feed
lines. This key is also used to release the slip paper
holder if numbers are not entered.
Slip print
Use this key to execute a slip batch printing on the slip
printer. Pressing this key prints the sales details. Actual
printing is performed following receipt issuance.
Square
This key provides the same functions as the Multiplication key. In addition, this key also has a square multiplication function.
Store
Use this key for storing the check number of the registered items. When this key is pressed, registered item
data will be stored, and then these data will transfer to
the youngest check number.
Table number
Use this key to input table numbers.
Table transfer
Use this key to transfer the contents of a check to another
check.
Takeout
Use this key to specify if the customer takes out items.
Before total a transaction. Press this key for the tax
exemption.
Tax exempt
Use this key to change taxable amounts to nontaxable
amounts.
Taxable amount subtotal
Use this key to obtain taxable amount subtotal.
Text print
Use this key to enter characters to print.
Text recall
Use this key to print preset characters.
Tip
Use this key to register tips.
Tray total
Use this key to display the total amount for all registrations from the last registration until this key is pressed or
registrations between presses of this key.
Void
Use this key to invalidate preceding item data registered.
25
Introducing TK-6000/6500
Normal receipt
Introducing TK-6000/6500
How to remove/replace the sheet holder (TK-6000 only)
Remove the sheet holder
Follow steps 1 ~ 2.
2
1
Replace the sheet holder
Follow steps 3 ~ 4.
3
4
26
How to install a menu sheet in the sheet holder (TK-6000 only)
Open the sheet holder
Follow the steps 1 ~ 3.
1
Introducing TK-6000/6500
1
1
UP
UP
2
3
Set a menu sheet in the sheet holder
Follow the steps 4 ~ 6.
UP ide
k s
Bac
5
9
36
27
18
26
17
8
15
6
33
24
5
32
23
14
UP
4
21
12
3
28
19
10
1
46
37
102
92
82
73
64
55
103
93
83
74
65
56
47
38
29
20
11
2
UP
39
30
104
94
84
75
66
57
48
105
95
85
76
67
58
49
40
31
22
13
50
41
106
86
77
68
59
96
87
78
69
60
51
42
107
97
88
79
70
61
52
43
34
25
16
7
53
44
35
108
98
89
80
71
62
99
90
81
72
63
54
45
101
91
1
4
100
UP
side
Back
6
27
18
9
13
4
1
TK-6000/6500 User’s Manual
29
11
2
10
20
28
38
37
47
46
56
55
65
64
74
73
103
93
84
75
66
57
48
39
30
21
12
3
31
22
58
49
40
104
94
85
76
67
105
95
86
77
68
59
50
41
32
23
14
5
33
24
15
6
60
51
42
106
96
87
78
69
107
97
88
79
70
61
52
43
34
25
16
7
35
26
17
8
62
53
44
108
98
89
80
71
99
90
81
72
63
54
45
36
83
82
102
92
101
91
1
100
19
27
Basic Operations and Setups
How to read the printouts
• The journal and receipts are records of all transactions and operations.
• The contents printed on receipts and journal are almost identical.
• You can choose the journal skip function.
If the journal skip function is selected, the cash register will print the total amount of each transaction, and the
details of premium, discount and reduction operations only, without printing department and PLU item registrations on the journal.
• The following items can be skipped on receipts and journal.
• Consecutive number
• Taxable status
• Taxable amount
• Item counter
Journal Sample
(Item lines Included)
Receipt Sample
************************
* THANK YOU *
— Logo message
**
CALL AGAIN
**
************************
*
*
*
*
COMMERCIAL
COMMERCIAL
COMMERCIAL
COMMERCIAL
MESSAGE
MESSAGE
MESSAGE
MESSAGE
*
*
— Commercial message
*
*
— Mode/Date/Time
REG 03-04-2000 11:58
C01
MC#01
000123 — Clerk/Machine No.
Consecutive No.
1 DEPT01
1 DEPT02
5 DEPT03
T1
T1
•1.00 — Q’ty/Item
•2.00
•5.00 — Item counter
7 No
TA1
TX1
TL
CASH
CG
***
***
***
***
BOTTOM
BOTTOM
BOTTOM
BOTTOM
•3.00
•0.15
•8.15
•10.00
•1.85
MESSAGE
MESSAGE
MESSAGE
MESSAGE
***
— Bottom message
***
***
***
REG 03-04-2000 11:58
C01
MC#01
000123
1 DEPT01
T1
•1.00
1 DEPT02
T1
•2.00
5 DEPT03
•5.00
7 No
TA1
•3.00
TX1
•0.15
TL
•8.15
CASH
•10.00
CG
•1.85
REG 03-04-2000 11:59
C02
MC#01
000124
1 DEPT01
T1
•1.00
1 DEPT03
T1
•3.00
1 DEPT02
T1
•2.00
1 DEPT04
T1
•4.00
5 DEPT05
•5.00
9 No
TA1
•10.00
TX1
•0.50
TL
•15.50
CASH
•20.00
CG
•4.50
Journal Sample
(Item lines Skipped)
REG 03-04-2000 11:57
C01
MC#01
000123
7 No
TA1
•3.00
TX1
•0.15
TL
•8.15
CASH
•10.00
CG
•1.85
REG 03-04-2000 11:57
C02
MC#01
000124
9 No
TA1
•10.00
TX1
•0.50
TL
•15.50
CASH
•20.00
CG
•4.50
REG 03-04-2000 11:58
C01
MC#01
000125
7 No
TA1
•3.00
TX1
•0.15
TL
•9.35
CASH
•10.00
CG
•0.65
REG 03-04-2000 11:59
In the operation examples contained in this manual, the print samples are what would be produced if the roll
paper is being used for receipts. They are not actual size. Actual receipts are 45 mm wide. Also, all sample receipts
and journals are printout images.
28
How to use your cash register
The following describes the general procedure you should use in order to get the most out of your cash register.
BEFORE business hours…
Basic Operations and Setups
• Check to make sure that the cash register is
plugged in securely.
Page 9
• Check to make sure there is enough paper
left on the roll.
Pages 10, 11
• Read the financial totals to confirm that they are
all zero.
Page 95
• Check the date and time.
Page 31
DURING business hours…
• Register transactions.
• Periodically read totals.
Page 32
Page 94
AFTER business hours…
•
•
•
•
TK-6000/6500 User’s Manual
Reset the daily totals.
Remove the journal.
Empty the cash drawer and leave it open.
Take the cash and journal to the office.
Page 53
Page 108
Page 17
29
Basic Operations and Setups
Assigning a clerk
On models available in the United States and Canada, clerk or cashier assignment can
be performed using clerk secret numbers only (clerk buttons are not equipped).
In Germany, you can assign clerks by using clerk key or by clerk secret number
(clerk key is equipped).
In other areas, you can assign clerks by using clerk button or by clerk secret number.
The method you of assigning clerk depends on the programming of your cash register.
ALL
Mode switch
Clerk button
You can assign the clerk or cashier using the four buttons located below the display panel.
Clerk lock/clerk key
You can assign the clerk or cashier inserting a clerk key into the clerk lock .
Clerk secret number key
When the cash register is programmed to use clerk secret numbers for clerk or cashier assignment, the clerk
buttons are not functional.
Clerk sign on
OPERATION
RECEIPT
1 6 o
2 6 o
Signing clerk 1 on:
* COMMERCIAL MESSAGE *
○
○
○
Signing clerk 2 on:
Signing clerk 10 on:
10 6 o
Clerk secret number
(1 ~ 10 is set as default.)
REG 03-04-2000 11:58
C01
MC#01
000123 — Clerk name/machine No./consecutive No.
1 DEPT01
T1
•1.00
• If you do not want the clerk secret number to be shown on the display, press o before entering the number.
Clerk sign off
OPERATION
Signing clerk off:
(except PGM mode)
0 6 o
• The current clerk is also signed off whenever you set the mode switch to OFF position.
Important!
• The error code “E008” appears on the display whenever you try to perform a registration, a read/
reset operation without signing on.
• A clerk cannot sign on unless other clerk is signed off.
• The signed on clerk is also identified on the receipt/journal.
30
Displaying the time and date
REG
You can show the time or date on the display of the cash register whenever there is
no registration being made.
Mode switch
To display and clear the time
OPERATION
DISPLAY
x or X
08-3~
Time appears on the display
Hour
Minutes
C
~00
Clears the time display
OPERATION
DISPLAY
x or X
08-3!
(Time is displayed first)
x or X
03-04-2000
Date appears on the display
C
~00
Clears the date display
Preparing coins for change
REG
You can use the following procedure to open the drawer without registering an item.
This operation must be performed out of a sale.
(You can use the r key instead of the N key. See page 52.)
Mode switch
Opening the drawer without a sale
OPERATION
RECEIPT
N
REG 03-04-2000 09:00
C01
MC#01
000001
#/NS
TK-6000/6500 User’s Manual
•••••••••
31
Basic Operations and Setups
To display and clear the date
Basic Operations and Setups
Preparing and using department/flat-PLU keys
Registering department/flat-PLU keys
REG
The following examples show how you can use the department/flat-PLU keys in
various types of registrations.
Mode switch
Single item sale
Example 1
OPERATION
RECEIPT
1-
Unit price $1.00
————————
——
Item Quantity
1
————————
——
Dept.
1
—————————————
Payment Cash
$1.00
Unit price
!
Department
— Date/time
REG 03-04-2000 09:05
C01
MC#01
000002 — Mode/consecutive No.
1 DEPT01
TL
CASH
•1.00 — Department No./unit price
•1.00 — Total amount
•1.00
F
Example 2 (Subtotal registration and change computation)
OPERATION
Unit price $12.34
————————
——
Item Quantity
1
————————
——
Flat-PLU
1
—————————————
Payment Cash
$20.00
1234
Unit price
(
Flat-PLU
s
F
20-F
RECEIPT
REG 03-04-2000 09:10
C01
MC#01
000003
1 PLU001
TL
CASH
CG
•12.34
•12.34 — Total amount
•20.00— Amount tendered
•7.66— Change
Amount tendered
Repeat
OPERATION
Unit price $1.50
————————
——
Item Quantity
3
————————
——
Dept.
1
—————————————
Payment Cash
$10.00
32
150!
!
!
s
10-F
RECEIPT
REG 03-04-2000 09:15
C01
MC#01
000004
1 DEPT01
1 DEPT01
1 DEPT01
TL
CASH
CG
•1.50
•1.50 — Repeat
•1.50 — Repeat
•4.50
•10.00
•5.50
Multiplication
OPERATION
RECEIPT
X
12X
Unit price $1.00
————————
——
Quantity
Item Quantity
12
(4-digit integer/2-digit decimal)
————————
——
1-(
Flat-PLU
1
—————————————
s
Payment Cash
$20.00
20-F
REG 03-04-2000 09:20
C01
MC#01
000005
•12.00 — Quantity/result
12 PLU0001
12
PLU00001
TL
CASH
CG
or
—
Quantity/unit q’ty/@
@1/ 1.00
—
•12.00 Result
•12.00
•20.00
•8.00
Basic Operations and Setups
• The model for the U.S./Canada, use x instead of X.
Split sales of packaged items
OPERATION
Unit price 4 for $10.00
————————
——
Quantity
3
Item ————————
——
Dept.
1
————————
——
Taxable
No
—————————————
Payment Cash
$10.00
RECEIPT
3x
x
Quantity being purchased
(4-digit integer/2-digit decimal)
REG 03-04-2000 09:25
C01
MC#01
000006
4x
x
Package quantity
(4-digit integer/2-digit decimal)
10-!
Package price
s
10-F
3 DEPT01
•7.50— Quantity/result
or
3
DEPT01
— Quantity/unit q’ty/@
@4/ 10.00
•7.50— Result
TL
CASH
CG
•7.50
•10.00
•2.50
• If x is not allocated on the keyboard, key allocation is necessary.
Programming department/flat-PLU keys
To program a unit price for each department/flat-PLU
Different setting
Same setting
PGM
6 1s 6 : : : : : : 6
Mode switch
Unit price
Department
6s
Flat-PLU
To program the tax calculation status for each department/flat-PLU
Tax calculation status
This specification defines which tax table should be used for automatic tax calculation.
TK-6000/6500 User’s Manual
33
Basic Operations and Setups
Programming procedure
To another department/flat-PLU
Same program
PGM
6 3s 60366s 6 : : 6
D2 D1
Mode switch
Department
6s
Flat-PLU
for the U.S./Singapore
Food stamp (for Singapore, always “0”)
Yes = 1
No = 0
Taxable 1 status
a
Yes = 1
No = 0
Taxable 2 status
b
Yes = 2
No = 0
Taxable 3 status
c
Yes = 4
No = 0
:
D2
:
(a+b+c)
D1
for Canada
Donuts status
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Yes = 1
No = 0
:
D2
Taxable 3 = 3
Taxable 4 = 4
Taxable 1 & 2 = 5
Taxable 1 & 3 = 6
Taxable 1 & 4 = 7
Significant
number
:
Taxable 4 = 4
Taxable 5 = 5
Taxable 6 = 6
Taxable 7 = 7
Taxable 8 = 8
Taxable 9 = 9
Taxable 10 = 10
Significant
numbers
::
D1
for other area
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
D2 D1
To program high amount limit for each department/flat-PLU
Programming procedure
PGM
To another department/flat-PLU
Same program
6 3s 61566s 6 :
Description
High amount limit for entering unit price manually.
34
: 6
~
D6 ~ D1
Mode switch
Choice
Significant
numbers
Department
Flat-PLU
Program code
::~::
D6 D5 ~ D2 D1
6s
Registering department/flat-PLU keys by programming data
REG
Mode switch
Preset price
OPERATION
REG 03-04-2000 09:30
C01
MC#01
000007
1 DEPT02
TL
CASH
•1.00 — Department No./unit price
•1.00
•1.00
Basic Operations and Setups
"
F
Unit price ($1.00)preset
—————————
Item Quantity
1
—————————
Dept.
2
—————————————
Payment Cash
$1.00
RECEIPT
Preset tax status
OPERATION
Unit price ($2.00)preset
—————————
Quantity
5
Item 1 —————————
Dept.
3
—————————
Taxable (1)preset
—————————————
Unit price ($2.00)preset
—————————
Quantity
1
Item 2 —————————
Dept.
4
—————————
Taxable (2)preset
—————————————
Payment Cash
$20.00
5X
#
$
s
20-F
RECEIPT
REG 03-04-2000 09:35
C01
MC#01
000008
Tax status
5 DEPT03
1 DEPT04
TA1
TX1
TA2
TX2
TL
CASH
CG
T1
T2
•10.00
•2.00
•10.00—
•0.40—
•2.00—
•0.20—
•12.60
•20.00
•7.40
Taxable Amount 1
Tax 1
Taxable Amount 2
Tax 2
• The model for the U.S./Canada, use x instead of X.
Locking out high amount limitation
OPERATION
Unit price $1.05
—————————
Quantity
1
Item —————————
Dept.
3
—————————
Max.amount($10.00)preset
—————————————
Payment Cash
$2.00
TK-6000/6500 User’s Manual
1050#
#
ERROR ALARM (E037)
(Exceeding high amount)
C
105#
s
2-F
RECEIPT
REG 03-04-2000 09:40
C01
MC#01
000009
1 DEPT03
TL
CASH
CG
•1.05
•1.05
•2.00
•0.95
35
Basic Operations and Setups
Preparing and using PLUs
This section describes how to prepare and use PLUs.
CAUTION:
Before you use PLUs, you must first program the unit price and tax status.
Programming PLUs
To program a unit price for each PLU
To new (not sequencial) PLU
Different program to the next PLU
Same program
PGM
6 1s 6 PLU No.+ 6 : : : : : : 6 a 6 s
Mode switch
Unit price
To program tax calculation status for each PLU
To new (not sequencial) PLU
Different program
to the next PLU
Same program
PGM
Mode switch
6 3s 6 0366s 6 PLU No.+ 6 : : 6 a 6 s
D2 D1
for the U.S./Singapore
Food stamp (for Singapore, always “0”)
Yes = 1
No = 0
Taxable 1 status
a
Yes = 1
No = 0
Taxable 2 status
b
Yes = 2
No = 0
Taxable 3 status
c
Yes = 4
No = 0
:
D2
:
(a+b+c)
D1
for Canada
Donuts status
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Yes = 1
No = 0
:
D2
Taxable 3 = 3
Taxable 4 = 4
Taxable 1 & 2 = 5
Taxable 1 & 3 = 6
Taxable 1 & 4 = 7
Significant
number
:
Taxable 4 = 4
Taxable 5 = 5
Taxable 6 = 6
Taxable 7 = 7
Taxable 8 = 8
Taxable 9 = 9
Taxable 10 = 10
Significant
numbers
::
D1
for other area
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
36
D2 D1
Registering PLUs
The following examples show how you can use PLUs in various types of
registrations.
REG
Mode switch
PLU single item sale
OPERATION
14
PLU code
+
s
3-F
REG 03-04-2000 09:45
C01
MC#01
000010
1 PLU0014
TL
CASH
CG
•2.50 — PLU No./unit price
•2.50
•3.00
•0.50
Basic Operations and Setups
Unit price ($2.50)preset
—————————
Item Quantity
1
—————————
PLU
14
—————————————
Payment Cash
$3.00
RECEIPT
PLU repeat
OPERATION
Unit price ($2.50)preset
—————————
Item Quantity
3
—————————
PLU
14
—————————————
Payment Cash
$10.00
14+
+
+
s
10-F
RECEIPT
REG 03-04-2000 09:50
C01
MC#01
000011
1 PLU0014
1 PLU0014
1 PLU0014
TL
CASH
CG
•2.50
•2.50
•2.50
•7.50
•10.00
•2.50
PLU multiplication
OPERATION
Unit price ($2.00)preset
—————————
Item Quantity
10
—————————
PLU
7
—————————————
Payment Cash
$20.00
10X
X
Quantity
(4-digit integer/2-digit decimal)
7+
s
20-F
RECEIPT
REG 03-04-2000 09:55
C01
MC#01
000012
10 PLU0007
10
PLU0007
TL
CASH
CG
•20.00 — Quantity/result
or
—
Quantity/unit q’ty/@
@1/ 2.00
—
•20.00 Result
•20.00
•20.00
•0.00
• The model for the U.S./Canada, use x instead of X.
TK-6000/6500 User’s Manual
37
Basic Operations and Setups
Split sales of packaged item
OPERATION
Unit price (5for$20.00)preset
——————————
Item Quantity
3
——————————
PLU
28
——————————————
Payment Cash
$15.00
3x
x
Quantity being purchased
(4-digit integer/2-digit decimal)
5x
x
Package quantity
(4-digit integer/2-digit decimal)
28+
s
15-F
RECEIPT
REG 03-04-2000 10:00
C01
MC#01
000013
3 PLU0028
•12.00 — Quantity/result
or
3
PLU0028
— Quantity/unit q’ty/@
@5/ 20.00
•12.00 — Result
•12.00
•15.00
•3.00
TL
CASH
CG
• If x is not allocated on the keyboard, key allocation is necessary.
Open PLU
OPERATION
30+
Unit price
$32.80
——————————
3280:
Item 1 Quantity
1
——————————
Unit price
PLU
30
——————————————
31+
Unit price
$13.00
——————————
13-:
Item 2 Quantity
2
——————————
Repeat
:
PLU
31
——————————————
Payment Cash
$60.00
RECEIPT
REG 03-04-2000 10:05
C01
MC#01
000014
1 PLU0030
•32.80
1 PLU0031
•13.00
1 PLU0031
•13.00
TL
•58.80
CASH
•60.00
CG
•1.20
s
60-F
• Before registering an open PLU, it is necessary to preset it as an open PLU.
38
Shifting the taxable status of an item
By pressing “Tax Shift” key, you can shift the taxable status of an item.
REG
Mode switch
Calculation merchandise subtotal
OPERATION
REG 03-04-2000 10:10
C01
MC#01
000015
1
1
1
1
DEPT01
DEPT02
DEPT03
DEPT04
TA1
TX1
TA2
TX2
TL
CASH
CG
T2
•4.00
T1
•2.00
T12 •6.00
•7.00
•8.00
•0.32
•10.00
•0.50
•19.82
•20.00
•0.18
Basic Operations and Setups
4-!
Dept. 1
$4.00
—————————
t
Item 1 Quantity
1
—————————
2-"
Taxable (2)preset
————————————— Pressing t changes the tax status
Dept. 2
$2.00 from Nontaxable to Taxable 1
—————————
T
Item 2 Quantity
1
—————————
6-#
Taxable (No)→1
————————————— Pressing T changes the tax status
Dept. 3
$6.00 from Taxable 1 to Taxable 1, 2
—————————
T
Item 3 Quantity
1
—————————
7-$
Taxable (1)→1, 2
————————————— Pressing T changes the tax status
Dept. 4
$7.00 from Taxable 2 to Nontaxable
—————————
s
Item 4 Quantity
1
—————————
20-F
Taxable (2)→No
—————————————
Payment Cash
$20.00
RECEIPT
Important!
• To change the tax status of the next item to be registered, be sure to press t, T.
If the last item registered is programmed as nontaxable, a discount (p key) operation on this item is
always nontaxable.
In this case, you cannot manually change the tax status to Taxable 1 or 2 by pressing the t, T
keys.
TK-6000/6500 User’s Manual
39
Basic Operations and Setups
Preparing and using discounts
This section describes how to prepare and register discounts.
Programming discounts
To program a rate to the p key
PGM
Mode switch
W
6 1s 6 : : : : 6 p 6 s
Preset rate
Example:
10% 2 10
5.5% 2 5^5
12.34% 2 12^34
Registering discounts
REG
The following example shows how you can use the p key in various types of
registration.
Mode switch
Discount for items and subtotals
OPERATION
Dept. 1
$5.00
—————————
Item 1 Quantity
1
—————————
Taxable
(1)preset
—————————————
PLU 16 ($10.00)preset
—————————
Item 2 Quantity
1
—————————
Taxable
(2)preset
—————————————
Discount Rate
(5%)preset
—————————————
Rate
3.5%
Subtotal ———————––––
discount Taxable Nontaxable
—————————————
Payment Cash
$15.00
5-!
16+
p
Applies the preset discount
rate to the last item registered.
s
p
3^5p
The input value takes priority
of the preset value.
s
15-F
RECEIPT
REG 03-04-2000 10:15
C01
MC#01
000016
1 DEPT01
1 PLU016
5%
%ST
3.5%
%TA1
TX1
TA2
TX2
TL
CASH
CG
T1
T2
•5.00
•10.00
T2
-0.50
•14.50
-0.51
•5.00
•0.20
•9.50
•0.48
•14.67
•15.00
•0.33
• You can manually input rates up to 4 digits long (0.01% to 99.99%).
Taxable status of the p key
• Whenever you perform a discount operation on the last item registered, the tax calculation for discount amount
is performed in accordance with the tax status programmed for that item.
• Whenever you perform a discount operation on a subtotal amount, the tax calculation for the subtotal amount is
performed in accordance with the tax status programmed for the p key.
40
Preparing and using reductions
This section describes how to prepare and register reductions.
Programming for reductions
You can use the m key to reduce single item or subtotal amounts.
To program preset reduction amount
PGM
6 1s 6 : : : : : : 6 m 6 s
Mode switch
Unit price
REG
Basic Operations and Setups
Registering reductions
The following examples show how you can use the m key in various types of
registration.
Mode switch
Reduction for items
OPERATION
Dept. 1
$5.00
—————————
Item 1 Quantity
1
—————————
Taxable
(1)preset
—————————————
Reduction Amount
$0.25
—————————————
PLU 45 ($6.00)preset
—————————
Item 2 Quantity
1
—————————
Taxable
(1)preset
—————————————
Reduction Amount ($0.50)preset
—————————————
Payment Cash
$11.00
5-!
m
25m
Reduces the last amount
registered by the value input.
45+
m
s
11-F
RECEIPT
REG 03-04-2000 10:20
C01
MC#01
000017
1 DEPT01
T1
•5.00
T1
-0.25
1 PLU0045
T1
•6.00
T1
-0.50
TA1
•10.25
TX1
•0.41
TL
•10.66
CASH
•11.00
CG
•0.34
• You can manually input reduction values up to 7 digits long.
• If you want to subtract the reduction amount from the department or PLU totalizer, program “Net totaling.”
TK-6000/6500 User’s Manual
41
Basic Operations and Setups
Reduction for subtotal
OPERATION
Dept. 1
$3.00
—————————
Item 1 Quantity
1
———————––––
Taxable
(1)preset
—————————————
Dept. 2
$4.00
—————————
Item 2 Quantity
1
———————––––
Taxable
(2)preset
—————————————
Amount
$0.75
Subtotal ———————––––
Reduction Taxable (No)
preset
—————————————
Payment Cash
$7.00
42
3-!
4-"
s
m
75m
Reduces the subtotal by the
value input here.
s
7-F
RECEIPT
REG 03-04-2000 10:25
C01
MC#01
000018
1 DEPT01
1 DEPT02
TA1
TX1
TA2
TX2
TL
CASH
CG
T1
T2
•3.00
•4.00
-0.75
•3.00
•0.12
•4.00
•0.20
•6.57
•7.00
•0.43
Registering credit and check payments
The following examples show how to register credits and payments by check.
REG
Mode switch
Check
OPERATION
11-!
s
k
20-k
REG 03-04-2000 10:30
C01
MC#01
000019
1 DEPT01
TL
CHECK
CG
•11.00
•11.00
•20.00
•9.00
Basic Operations and Setups
Dept. 1
$11.00
—————————
Quantity
1
—————————————
Payment Check
$20.00
Item
RECEIPT
Credit
OPERATION
Dept. 4
$15.00
Item —————————
Quantity
1
—————————————
Reference Number
1234
—————————————
Payment Credit
$15.00
15-$
s
N
1234N
c
RECEIPT
REG 03-04-2000 10:35
C01
MC#01
000020
1 DEPT04
•15.00
#/NS
1234 — Reference No.
TL
•15.00
CREDIT1
•15.00
Mixed tender (cash, credit and check)
OPERATION
Dept. 4
$55.00
—————————
Quantity
1
—————————————
Check
$30.00
—————————
Payment Cash
$5.00
—————————
Credit
$20.00
Item
TK-6000/6500 User’s Manual
55-$
s
k
30-k
F
5-F
c
RECEIPT
REG 03-04-2000 10:40
C01
MC#01
000021
1 DEPT04
•55.00
TL
•55.00
CHECK
•30.00
CASH
•5.00
CREDIT1
•20.00
43
Basic Operations and Setups
Preparing and registering the Euro
Basic programming for the Euro and its exchange rate
Before registering the Euro, you must define the main currency, and its exchange rate.
If you need to select cash drawer or some rounding specification, please ask your dealer.
Description
Define the euro as the main currency.
Select rounding option:
Round off = 0, Cut off = 1, Round up = 2
D10
Significant
numbers
Decimal point position of exchange rate:
Integer only = 0
1st decimal place = 1, 2nd decimal place = 2, 3rd decimal place = 3,
4th decimal place = 4, 5th decimal place = 5, 6th decimal place = 6
Example: (D8 ~ D2)
1Euro = 1.977DM; Set “001977”
1Euro = 1957.77319 Lit; Set “1957772”
Significant
number (0 ~ 6)
:
:
D9
::::::
D8 D7 D6 D5 D4 D3
:
D2
;
Always “0”
Mode switch
Program code
Significant
number (0 ~ 2)
Exchange rate (within 6-digits)
PGM
Choice
Yes = 0
No = 1
D1
6 3s 62822s 6 : ------- : 6 a 6 s
D10 ------- D1
Registering the Euro
REG
The following example shows the basic operation using the currency exchange
function.
Mode switch
(1) Case A
(2) Case B
44
Main currency
Payment
Change
Rate
Local
Euro
Local
1 Euro = 0.5 FFr
Main currency
Payment
Change
Rate
Euro
Local
Euro
1 Euro = 0.5 FFr
Case A
OPERATION
DISPLAY
600 !
q 1
s
Press the q key, which converts the subtotal amount
into the sub currency by applying the preset exchange
rate.
After you press the s key, the result is shown on the
display.
q 1
Press the q key if you enter the payment in the sub
currency.
15-
~00e
1"00e
~00e
1%00e
Press the a key to finalize the transaction.
The change amount is shown in the programmed
currency.
!50
Case B
OPERATION
DISPLAY
12- !
q 1
s
q 1
6-
~00l
Press the q key if you enter the payment in the sub
currency.
~00l
&00l
&00l
a 1
Printouts
Press the q key, which converts the subtotal amount
into the sub currency by applying the preset exchange
rate.
After you press the s key, the result is shown on the
display.
Press the a key to finalize the transaction.
The change amount is shown in the programmed
currency.
CASE A
CASE B
REG 03-04-2000 10:45
C01
MC#01
000022
1 DEPT01
TL
EURO money
CASH
CASH
CG
TK-6000/6500 User’s Manual
~00
•6.00
•6.00
⁄12.00
⁄15.00
•7.50
•1.50
REG 03-04-2000 10:50
C01
MC#01
000023
1 DEPT01
TL
LOCAL money
CASH
CASH
CG
⁄12.00
⁄12.00
•6.00
•6.00
⁄12.00
⁄0.00
45
Basic Operations and Setups
a 1
Basic Operations and Setups
Validation printing
You can perform total amount validation following finalization using a, h, k,
c, d keys and r, P keys. Also you can perform single item validation.
REG
Mode switch
Total amount validation
OPERATION
Dept. 1
$14.00
—————————
Quantity
1
—————————————
Payment Check
$20.00
—————————————
Validation
Item
14-!
s
20-k
RECEIPT
REG 03-04-2000 10:55
C01
MC#01
000024
1 DEPT01
TL
CHECK
CG
•14.00
•14.00
•20.00
•6.00
1 Open the journal window.
2 Insert paper.
3 Press v.
1
2
Validation sample
70 mm Min.
135 mm ~ 210 mm
Mode (4 digits)
Clerk name (6 digits)
Date (6 digits), Time (4 digits)
Machine/Cons. No. (6 digits ea.)
Key descriptor
Amount
Format A
REG C01
Format B
46
REG C01
030400 1055 MC#01 000024 CHECK
030400 1055 MC#01 024 CHECK
•20.00
•20.00
Registering returned goods in the REG mode
The following example shows how to use the R key in the REG mode to register
goods returned by customers.
REG
Mode switch
Dept. 1
$2.35
Item 1 —————————
Quantity
1
—————————————
Dept. 2
$2.00
Item 2 —————————
Quantity
1
—————————————
PLU 1 ($1.20)preset
Item 3 —————————
Quantity
1
—————————————
Dept. 1
$2.35
Returned —————————
Item 1 Quantity
1
—————————————
PLU 1 ($1.20)preset
Returned —————————
Item 3 Quantity
1
—————————————
Payment Cash
$2.00
235!
2-"
1+
R
235!
Press R before the item you
want to return.
R
1+
s
F
RECEIPT
REG 03-04-2000 11:00
C01
MC#01
000025
1 DEPT01
1 DEPT02
1 PLU0001
RF
1 DEPT01
RF
1 PLU0001
TL
CASH
•2.35
•2.00
•1.20
•••••••••
-2.35
•••••••••
-1.20
•2.00
•2.00
Registering returned goods in the RF mode
RF
The following examples show how to use the RF mode to register goods returned by
customers.
Mode switch
Normal refund transaction
OPERATION
Dept. 1
$1.50
Returned —————————
Item 1 Quantity
2
—————————————
PLU 2 ($1.20)preset
Returned —————————
Item 2 Quantity
6
—————————————
Payment Cash
$10.20
150!
!
6X
2+
F
RECEIPT
—————————————— RF mode symbol
RF 03-04-2000 11:05
C01
MC#01
000026
1 DEPT01
•1.50
1 DEPT01
•1.50
6 PLU0002
•7.20
TL
•10.20
CASH
•10.20
• The model for the U.S./Canada, use x instead of X.
TK-6000/6500 User’s Manual
47
Basic Operations and Setups
OPERATION
Basic Operations and Setups
Reduction of amounts paid on refund
OPERATION
Dept. 3
$4.00
Returned —————————
Item 1 Quantity
1
—————————————
Reduction Amount
$0.15
—————————————
PLU 2 ($1.20)preset
Returned —————————
Item 2 Quantity
1
—————————————
Discount Rate
(5%)preset
—————————————
Payment Cash
$5.20
4-#
15m
2+
p
s
F
RECEIPT
RF 03-04-2000 11:10
C01
MC#01
000027
1 DEPT03
1 PLU0002
5%
%TA1
TX1
TA2
TX2
TL
CASH
T1
T1
T2
•4.00
-0.15
•1.20
T2
-0.06
•3.85
•0.15
•1.14
•0.06
•5.20
•5.20
Important!
• To avoid miss registrations in the RF mode, return the mode switch to the former position immediately.
Registering money received on account
REG
The following example shows how to register money received on account. This
registration must be performed out of a sale.
Mode switch
OPERATION
Received amount
$700.00
7--r
r
Amount can be up to 8 digits.
RECEIPT
REG 03-04-2000 11:15
C01
MC#01
000028
RC
•700.00
Registering money paid out
REG
The following example shows how to register money paid out from the register. This
registration must be performed out of a sale.
Mode switch
OPERATION
Paid out amount
$1.50
P
150 or
q
Amount can be up to 8 digits.
48
RECEIPT
REG 03-04-2000 11:20
C01
MC#01
000029
PD
•1.50
Registering loan amounts
Use this procedure to register loan or bank received from the office.
REG
Mode switch
OPERATION
Note
$1.00
—————————
Quantity
10
Item —————————
Note
$5.00
—————————
Quantity
5
—————————————
Media
Cash
$35.00
10X
l
1-l
5X
l
5-l
a
RECEIPT
REG 03-04-2000 11:25
C01
MC#01
000030
LOAN
LOAN
CASH
•10.00
•25.00
•35.00
Basic Operations and Setups
• The model for the U.S./Canada, use x instead of X.
Registering pick up amounts
Use this procedure to register pick up money from cash drawer.
REG
Mode switch
OPERATION
Coin
$0.50
—————————
Quantity
10
Item —————————
Coin
$0.10
—————————
Quantity
5
—————————————
Media
Cash
$5.50
10X
L
50L
5X
L
10L
a
RECEIPT
REG 03-04-2000 11:30
C01
MC#01
000031
P.UP
P.UP
CASH
•5.00
•0.50
•5.50
• The model for the U.S./Canada, use x instead of X.
Changing media in drawer
Use this procedure to change media in drawer.
REG
Mode switch
OPERATION
i
Check
-10.00
—————————
10-k
Media
Cash
$8.00
————————— Enter the amount to be changed.
Charge
$2.00
8-a
2-h
TK-6000/6500 User’s Manual
RECEIPT
REG 03-04-2000 11:35
C01
MC#01
000032
MEDIA CHG
CHECK
CASH
CH
•••••••••
•10.00
•8.00
•2.00
49
Basic Operations and Setups
Making corrections in a registration
There are three techniques you can use to make corrections in a registration.
• To correct an item that you input but not yet registered.
• To correct the last item you input and registered.
• To cancel all items in a transaction.
REG
Mode switch
To correct an item you input but not yet registered
OPERATION
2-
RECEIPT
—
REG 03-04-2000 11:40
C01
MC#01
000033
C — Correction of unit price
1 DEPT01
1-! —
11 DEPT02
12X —
1 PLU0003
1 PLU0015
C
TL
— Correction of quantity
CASH
11X
CREDIT1
2-" —
2
—
C — Correction of PLU No.
3+ —
15+ —
6C — Correction of open PLU unit price
15+
Enter PLU No. again.
10-: —
s
10—
C — Correction of partial tender amount
15-F —
c
• The model for the U.S./Canada, use x instead of X.
50
•1.00
•22.00
•1.30
•10.00
•34.30
•15.00
•19.30
To correct an item you input and registered
1-!
2-"
"—
— Clearance
e—
2+ —
e — Correction of PLU No.
5+ —
15+ —
6-:
e — Correction of open
PLU unit price
15+
10-: —
8X —
4-$
e — Correction of quantity
6X
4-$ —
s—
50p
e — Correction of discount
s
5p —
R2-" —
e — Correction of refund item
R220" —
s
20-F —
e — Correction of partial tender
15-F —
c
RECEIPT
REG 03-04-2000 11:45
C01
MC#01
000034
1 DEPT01
•1.00
1 DEPT02
•2.00
1 DEPT02
•2.00
CORR
-2.00
1 PLU0002
•1.20
CORR
-1.20
1 PLU0005
•1.50
1 PLU0015
•6.00
CORR
-6.00
1 PLU0015
•10.00
8 DEPT04
•32.00
CORR
-32.00
6 DEPT04
•24.00
ST
•38.50
50%
%-19.25
CORR
•19.25
ST
•38.50
5%
%-1.93
RF
•••••••••
1 DEPT02
-2.00
CORR
•2.00
RF
•••••••••
1 DEPT02
-2.20
TL
•34.37
CASH
•20.00
CORR
-20.00
CASH
•15.00
CREDIT1
•19.37
Basic Operations and Setups
OPERATION
• The model for the U.S./Canada, use x instead of X.
TK-6000/6500 User’s Manual
51
Basic Operations and Setups
To cancel all items in a transaction
OPERATION
RECEIPT
1-!
2-"
3-#
4-$
s
Pressing s key is necessary to cancel
the transaction.
REG 03-04-2000 11:50
C01
MC#01
000035
1
1
1
1
DEPT01
DEPT02
DEPT03
DEPT04
CANCEL
•1.00
•2.00
•3.00
•4.00
•••••••••
e
No sale registration
REG
You can use the following procedure to open the drawer without registering a sale.
This operation must be performed out of a sale.
Mode switch
OPERATION
RECEIPT
N
REG 03-04-2000 11:55
C01
MC#01
000036
#/NS
52
•••••••••
Printing the daily sales reset report
This report shows daily sales totals.
OPERATION
REPORT
CH
56
•1,174.85
RC
No
4
•810.00
PD
No
5
•520.00
•5.00
CORR
No
14
•39.55
VLD
No
19
RCT
No
3
NS
No
5
-----------------------Z
DEPT
0001 — Department report title/reset counter
0001015 — Report code
Mode switch
8
F
—
Z 03-04-2000 17:40
C01
MC#01
000174 —
-----------------------—
Z
BATCH01
-----------------------Z
FIX
0001 —
0001011 —
GROSS
981.25 —
•6,574.40
NET
No
111
—
•7,057.14
CAID
•1,919.04 —
CHID
•139.04 —
CKID
•859.85 —
CRID(1)
•709.85 —
-----------------------RF
No
3
—
•10.22
—
CUST
CT
111
AVRG
•63.57 —
DC
•1.22 —
REF
•2.42 —
—
CLEAR
No
85
ROUND
•0.00 —
CANCEL
No
2
—
•12.97
-----------------------TA1
•2,369.69 —
TX1
•128.86 —
TA2
•2,172.96 —
TX2
•217.33 —
-----------------------GT1
•00000000125478.96 —
GT2
•00000000346284.23 —
GT3
•00000000123212.75 —
-----------------------Z
TRANS
0001 —
0001012 —
CASH
No
362
—
•1,638.04
Date/time
Clerk name/mc No./consecutive No.
Report title
Fixed total report title/reset counter
Report code
No
DEPT01
203.25 —
•1,108.54
DEPT02
183
•1,362.26
DEPT04
5
•17.22
-----------------------TL
421.25 —
•2,872.28
-----------------------Z
CASHIER
0001 —
0001017 —
Gross total *2
Net total *2
Cash in drawer *2
Charge in drawer *2
Check in drawer *2
Credit in drawer *2
Refund mode *2
Number of customer *2
Average sales per customer *2
Discount total *2
Refund key *2
Clear key count *2
Rounding total *2
C01
GROSS
NET
Cancellation *2
CAID
CHID
RF
Taxable 1 amount *2
Tax 1 amount *2
Taxable 2 amount *2
Tax 2 amount *2
CLEAR
Grand total 1 *2
Grand total 2 *2
Grand total 3 *2
C02
...........1 —
421.25 —
•2,872.28
No
111
—
•1,845.35
•1,057.14 —
•139.04
No
1
—
•1.00
No
5
—
•4.43
Department count/amount *1
Department total count/total amount
Clerk report title/reset counter
Report code
Clerk name/drawer No. *1
Gross total *1
Net total *1
Cash in drawer *1
Refund mode *1
Clear key count *1
...........1 — Clerk name/drawer No.
Function key report title/reset counter
Report code
*1
Function key count/amount *1
TK-6000/6500 User’s Manual
*2
Zero totalled departments/functions/clerks are not printed by
programming.
These items can be skipped by programming.
53
Basic Operations and Setups
Z1
Advanced Operations
This chapter describes more sophisticated operations that you can use to suit the needs of your retail
environment.
Clerk interrupt function
There are two types of clerk interrupt function, illustrated by PROCEDURE 1 and PROCEDURE 2 below.
• In PROCEDURE 1, each clerk possesses a unique clerk interrupt buffer, and so the clerk interrupt function
gives each individual clerk the ability to perform an independent registration operation. In this case, each clerk
is individually linked to a unique clerk interrupt buffer.
• In PROCEDURE 2, multiple clerks use the same clerk interrupt buffer, and so a single clerk interrupt
operation (clerk change during registration) can be performed any registration is in progress.
In this case, multiple clerks are linked to a single clerk interrupt buffer.
Note the following important points concerning the clerk interrupt function.
• The register must be programmed to allow the clerk interrupt function.
• To use the clerk interrupt function, a clerk interrupt buffer must be allocated with the memory allocation
operation. Next the manager control operation (X1 mode) should be used to perform clerk assignment for the
clerk interrupt function. The clerk interrupt operation cannot be performed by clerks who are not linked to a
clerk interrupt buffer.
• You cannot use the clerk interrupt function on a register set up to function as part of a check tracking system.
In the REG1, REG2, and RF modes, clerks can be changed while a transaction is in progress, making it
possible for multiple clerks to simultaneously perform registrations in the same mode using a single register.
For example, if clerk 1 is interrupted while registering a transaction, clerk 2 can use the same machine to
register a different transaction. Then clerk 1 can continue the original registration from the point where it was
interrupted.
PROCEDURE 1
Clerk 1
Sign on
<NEW BALANCE>
Sign on
Registration A
<CASH>
Sign on
Finalization A
Sign on
Clerk 2
<NEW BALANCE>
Registration B
<RECEIPT>
Post receipt A
Sign on
<CASH>
Finalization B
PROCEDURE 2
Clerk 1
Sign on
<NEW BALANCE>
Registration A
<CASH>
Finalization A + B
Sign on
Clerk 2
Sign on
<NEW BALANCE>
Registration B
NOTES
• A guest receipt can be issued following clerk change, and receipts can be issued separately for each clerk.
• A cancel operation can be performed during registration by either of the clerks. When clerk 1 signs back on
(after being interrupted by clerk 2), the cancel operation cancels only the items registered after signing back on
(only this receipt) or from the top of the transaction. This is selectable by the key program.
54
Single item cash sales
A department key or PLU programmed with single item sale status finalizes the transaction as soon as it is
registered.
The single item sales function cannot work properly if the keyboard does not include <CASH> (the cash key).
The single item sales function can only be used for cash sales.
Example 1
OPERATION
Dept. 1
$1.00
————————
——
Item Quantity
1
————————
——
Status
S.I.S
—————————————
Payment Cash
$1.00
1-!
!
The transaction is
immediately finalized.
RECEIPT
— Mode/date/time
REG 03-04-2000 13:00
C01
MC#01
000101 — Clerk/consecutive No.
1 DEPT01
TL
CASH
•1.00— Department No./unit price
•1.00 — Cash total amount
•1.00
Example 2
OPERATION
3X
!
The transaction is
immediately finalized.
REG 03-04-2000 13:05
C01
MC#01
000102
3 DEPT01
TL
CASH
Advanced Operations
Dept. 1
($1.00)
————————
——
Item Quantity
3
————————
——
Status
S.I.S
—————————————
Payment Cash
$3.00
RECEIPT
•3.00
•3.00
•3.00
• The model for the U.S./Canada, use x instead of X.
Example 3
OPERATION
Dept. 3
$2.00
————————
——
Item 1 Quantity
1
————————
——
Status
Normal
—————————————
Dept. 1
$1.00
————————
——
Item 2 Quantity
1
————————
——
Status
S.I.S
—————————————
Payment Cash
$3.00
TK-6000/6500 User’s Manual
2-#
!
The transaction is not finalized.
Because another item is
registered before the single
item sales department.
F
RECEIPT
REG 03-04-2000 13:10
C01
MC#01
000103
1 DEPT03
1 DEPT01
TL
CASH
•2.00
•1.00
•3.00
•3.00
55
Advanced Operations
Addition
Addition (plus)
Example
OPERATION
Dept. 1
$1.00
————————
——
Item 1 Quantity
1
————————
——
Addition $0.10
—————————————
Dept. 1
$2.00
————————
——
Item 2 Quantity
3
————————
——
Addition 3 × ($0.20)
—————————————
Payment Cash
$7.70
1-!
+
B
10B
3X
2-!
3X
+
B
F
RECEIPT
REG 03-04-2000 13:15
C01
MC#01
000104
1 DEPT01
+
3 DEPT01
+
TL
CASH
•1.00
•0.10
•6.00
•0.60
•7.70
•7.70
• The model for the U.S./Canada, use x instead of X.
Premium (%+)
Example
OPERATION
Dept. 1
$1.00
————————
——
Item 1 Quantity
1
————————
——
Premium
10%
—————————————
Dept. 1
$2.00
Item 2 ————————
——
Quantity
3
—————————————
Subtotal Premium
15%
—————————————
Payment Cash
$8.17
1-!
%+
B
10B
3X
2-!
s
%+
B
F
• The model for the U.S./Canada, use x instead of X.
56
RECEIPT
REG 03-04-2000 13:20
C01
MC#01
000105
1 DEPT01
10%
%+
3 DEPT01
ST
15%
%+
TL
CASH
•1.00
•0.10
•6.00
•7.10
•1.07
•8.17
•8.17
Tray total
Tray total premium/discount
The buffer memory stores all items that fall into the prescribed range, starting from the first item registered for
a transaction up to the point that <TRAY TOTAL> (the tray total key) is pressed to perform a tray total
premium/discount operation. Following a premium/discount operation, the buffer is cleared and storage of new
data starts from registration of the next item following the first premium/discount operation. The following
operations clear the buffer memory.
• Press <TRAY TOTAL> twice.
• Press <TRAY TOTAL> and then perform a premium/discount operation. The contents of the buffer memory are
restored if an error correction operation is performed to delete the premium/discount operation.
Example
OPERATION
RECEIPT
1-!
2-#
TRAY
B
TOTAL
p
3-#
4-$
TRAY
B
TOTAL
10p
F
REG 03-04-2000 13:25
C01
MC#01
000106
1 DEPT01
1 DEPT03
TRAY TL
5%
%1 DEPT03
1 DEPT04
TRAY TL
10%
%TL
CASH
•1.00
•2.00
•3.00
-0.15
•3.00
•4.00
•7.00
-0.70
•9.15
•9.15
Multiple item totalling function
This function accumulates all items registered from the first item registered up to point that <TRAY TOTAL>
is pressed, or all items between two presses of <TRAY TOTAL>. Pressing <TRAY TOTAL> displays the total
amount with the tax included and prints it on the receipt and journal (printing on receipt and journal is
programmable.)
Example
OPERATION
RECEIPT
Dept. 1
$1.00
Customer A————————
——
Dept. 3
$2.00
—————————————
Dept. 3
$3.00
Customer B————————
——
Dept. 4
$4.00
—————————————
Payment Cash
$10.00
TK-6000/6500 User’s Manual
1-!
2-#
TRAY
B
TOTAL
3-#
4-$
TRAY
B
TOTAL
F
REG 03-04-2000 13:30
C01
MC#01
000107
1 DEPT01
•1.00
1 DEPT03
•2.00
TRAY TL
•3.00
1 DEPT03
•3.00
1 DEPT04
•4.00
TRAY TL
•7.00
TL
•10.00
CASH
•10.00
57
Advanced Operations
Dept. 1
$1.00
————————
——
Group 1 Dept. 3
$2.00
————————
——
Discount (5%)preset
—————————————
Dept. 3
$3.00
————————
——
Group 2 Dept. 4
$4.00
————————
——
Discount
10%
—————————————
Payment Cash
$9.15
Advanced Operations
Coupon transactions
Note that errors result when the result of a calculation is negative if the cash register is programmed to prohibit
credit balances.
Coupon registration using <COUPON> (coupon key)
Example
OPERATION
Dept. 1
$3.00
————————
——
Item 1 Quantity
2
————————
——
Coupon $0.50 × 2
—————————————
Dept. 3
$4.00
————————
——
Item 2 Quantity
1
————————
——
Coupon ($1.00)
—————————————
Payment Cash
$8.00
2X
3-!
2X
CPN
B
50B
4-#
CPN
B
F
RECEIPT
REG 03-04-2000 13:35
C01
MC#01
000108
2 DEPT01
CPN
1 DEPT03
CPN
TL
CASH
•6.00
-1.00
•4.00
-1.00
•8.00
•8.00
• The model for the U.S./Canada, use x instead of X.
Coupon registration using <COUPON2> (coupon 2 key)
Example
OPERATION
Dept. 1
$15.00
————————
——
Quantity
1
Item 1 ————————
——
Coupon 2
$1.50
Dept.1
—————————————
PLU 10
$5.00
————————
——
Quantity
1
Item 2 ————————
——
Coupon 2
($0.50)
PLU 50
—————————————
Payment Cash
$18.00
58
15-!
CPN2 150!
B
10+
CPN2 50+
B
F
RECEIPT
REG 03-04-2000 13:40
C01
MC#01
000109
1 DEPT01
•15.00
CPN2
•••••••••
1 DEPT01
-1.50
1 PLU0010
•5.00
CPN2
•••••••••
1 PLU0050
-0.50
TL
•18.00
CASH
•18.00
Preset tender amount
An amount up to six digits long can be programmed to <CASH> (cash/amount tendered key). Then, when
<CASH> is pressed without inputting a value, the programmed value is automatically registered and the
transaction is finalized. When an amount is programmed to <CASH>, attempting to manually input an amount
results in an error.
Example 1
OPERATION
RECEIPT
Dept. 1
$8.00
————————
——
Quantity
1
—————————————
Payment Cash
($10.00)
Item
8-!
F
The preset amount is tendered.
REG 03-04-2000 13:45
C01
MC#01
000110
1 DEPT01
TL
CASH
CG
•8.00
•8.00
•10.00
•2.00
Example 2
OPERATION
TK-6000/6500 User’s Manual
15-!
10-F
An error occurs by manual input
C
5-k
F
REG 03-04-2000 13:50
C01
MC#01
000111
1 DEPT01
TL
CHECK
CASH
CG
Advanced Operations
Dept. 1
$15.00
————————
——
Quantity
1
—————————————
Cash
($10.00)
Payment ————————
——
Check
$5.00
Item
RECEIPT
•15.00
•15.00
•5.00
•10.00
•0.00
59
Advanced Operations
Bottle link operation
You can link PLU or subdepartment to a PLU.
Example
OPERATION
PLU 1
($8.00)
————————
——
Item 1 PLU 11linked ($0.80)
————————
——
Quantity
1
—————————————
PLU 2
($5.00)
————————
——
Item 2 PLU 12linked ($0.50)
————————
——
Quantity
3
—————————————
Payment Cash
$30.00
1+
3X
2+
30-F
RECEIPT
REG 03-04-2000 13:55
C01
MC#01
000112
1
1
3
3
PLU0001
•8.00
PLU0011
•0.80
PLU0002
•15.00
PLU0012
•1.50
TL
•25.30
CASH
•30.00
CG
•4.70
• The model for the U.S./Canada, use x instead of X.
Bottle returns
Bottle return key
You can use the linked bottle return key to register a bottle return. A PLU whose programmed unit price
represents the contents of the bottle, can be linked with PLU whose programmed unit price represents the
deposit on the bottle. In the following example, the bottle return key has been programmed to operate as a
linked bottle return key.
The bottle return key must be pressed before input of each new linked bottle return.
Example
OPERATION
RECEIPT
PLU 1
($8.00)
————————
——
Return PLU 11
($0.80)
linked
Item 1
————————
——
Quantity
1
—————————————
PLU 2
($5.00)
————————
——
Return PLU 12
($0.50)
linked
Item 2
————————
——
Quantity
3
—————————————
Payment Cash
$2.30
BR 1+
B
3X
BR 2+
B
F
• The model for the U.S./Canada, use x instead of X.
60
REG 03-04-2000 14:00
C01
MC#01
000113
BR
1 PLU0011
BR
3 PLU0012
TL
CASH
•••••••••
-0.80
•••••••••
-1.50
-2.30
-2.30
Arrangement key registrations
Key operations can be assigned to an <ARRANGE> (arrangement key). Then, simply pressing <ARRANGE>
performs all of the key functions assigned to it.
Key operations can also be assigned to an address code. Then, when you input the address code using
<ARRANGE>, all of the key functions assigned to the address code are performed.
Example 1
OPERATION
RECEIPT
A
Arrangement 1
—————————————
PLU 1
($8.00)
Item 1 ————————
——
Quantity
1
—————————————
PLU 2
($5.00)
Item 2 ————————
——
Quantity
1
—————————————
Payment Cash
$13.00
REG 03-04-2000 14:05
C01
MC#01
000114
1 PLU0001
•8.00
1 PLU0002
•5.00
TL
•13.00
CASH
•13.00
Example 2
Arrangement 5
—————————————
Dept. 1
$1.00
Item 1 ————————
——
Quantity
1
—————————————
Dept. 2
$2.00
Item 2 ————————
——
Quantity
1
—————————————
Payment Cash
$3.00
5A
A
RECEIPT
Advanced Operations
OPERATION
REG 03-04-2000 14:10
C01
MC#01
000115
1 DEPT01
1 DEPT02
TL
CASH
•1.00
•2.00
•3.00
•3.00
Set menu
When you register a set menu, its total amount is added to the PLU totalizer and counter. The price of each set
menu item is also added to each respective PLU totalizer and counter.
Example
OPERATION
RECEIPT
Set menu PLU 35
$5.00
—————————————
Item 1
PLU 1
-————————
——
Item 2
PLU 2
-—————————
Item 3
PLU 3
-————————
——
Item 4
PLU 4
-—————————————
Payment Cash
$5.00
TK-6000/6500 User’s Manual
35+
+
F
REG 03-04-2000 14:15
C01
MC#01
000116
1 PLU0035
PLU0001
PLU0002
PLU0003
PLU0004
TL
CASH
•5.00
•5.00
•5.00
61
Advanced Operations
Currency exchange function
When <CE> (currency exchange key) is pressed, a current subtotal including tax is converted directly into
foreign currency and the result is displayed, and the subsequent finalization is handled using the foreign
currency. The currency exchange function is released by finalizing a transaction, partial tender operation,
receipt issuance, or by pressing <SUBTOTAL>.
Before using the currency exchange function, it is necessary to program the conversion rate.
Registering foreign currency
Full amount tender in foreign currency
* Pre-programmed exchange rate: ¥ 100 = $0.9524
Important!
Tenders in a foreign currency can be registered using a and k only.
Other finalize keys cannot be used.
OPERATION
10-!
5 Enter the unit price and press the
applicable department key.
20-"
5 Enter the next unit price and press
the applicable department key.
Es
5 Press E and s without entering a numeric value. This operation converts the subtotal (including tax) dollar value into yen
by applying a pre-programmed exchange rate. The result is shown
on the display and printed on the
receipt/journal by programming.
50-E
E
5 Enter the amount tendered in yen
and press E. This operation
converts the entered yen
amount into dollars by applying a
pre-programmed exchange rate.
The result is shown on the display.
(5,000)
a
62
DISPLAY
5 Press to finalize the transaction.
Note that you do not need to reenter the dollar amount.
The register automatically calculates the change amount due in
dollars and shows it on the display, receipts and journal.
01 1~00
(Displays in $)
02 2~00
(Displays in $)
#150
(Displays in ¥: 3,150)
%000
1¶62
(Displays in $)
RECEIPT
REG 03-04-2000 14:20
C01
MC#01
000117
1 DEPT01
2 DEPT02
TL
CE
CASH
CASH
CG
•10.00
•20.00
•30.00
¥5,000
•47.62
•17.62
Partial tender in a foreign currency
* Pre-programmed exchange rate: ¥ 100 = $0.9524
Important!
Partial tender in a foreign currency can be registered using a and k only. Other finalization
keys cannot be used, but the remaining tender can be finalized using any finalize key.
DISPLAY
10-!
5 Enter the unit price and press the
applicable department key.
01 1~00
20-"
5 Enter the next unit price and press
the applicable department key.
02 2~00
Es
5 Press E and s without entering a numeric value. This operation converts the subtotal (including tax) dollar value into yen
by applying a pre-programmed exchange rate. The result is shown
on the display and printed on the
receipt/journal by programming.
#150
(Displays in $)
(Displays in $)
(Displays in ¥: 3,150)
20-E
E
5 Enter the partial amount tendered
in yen and press E.
This operation converts the entered yen amount into dollars by
applying a pre-programmed exchange rate. The result is shown
on the display.
"000
a
5 Press a to specify cash tender
for the yen partial tender. Note
that you do not need to reenter the
dollar amount.
The register automatically deducts
the dollar equivalent of the yen
amount tendered from the total
amount due and shows the amount
on the display.
1~95
k
5 Press to finalize the transaction.
(2,000)
TK-6000/6500 User’s Manual
RECEIPT
REG 03-04-2000 14:25
C01
MC#01
000118
1 DEPT01
1 DEPT02
TL
CE
CASH
CASH
CHK
•10.00
•20.00
•30.00
¥2,000
•19.05
•10.95
Advanced Operations
OPERATION
(Displays in $)
1~95
(Displays in $)
63
Advanced Operations
Food stamp function
Food stamp registration
No change due
REG
Mode switch
OPERATION
Dept. 1
$1.00
Item 1 —————————
Taxable
1, F/S
—————————————
Dept. 2
$2.00
Item 2 —————————
Taxable
2
—————————————
Dept. 3
$3.00
Item 3 —————————
Taxable No → F/S
—————————————
Food stamp $2.00
Payment —————————
Cash
$4.14
64
RECEIPT
1-!
2-"
K3-#
Shifting food stamp
status, press K key.
J
Press J, at the top of
the food stamp tender.
2-I
I
a
REG 03-04-2000 14:30
C01
MC#01
000119
1 DEPT01
1 DEPT02
1 DEPT03
TA1
TX1
TA2
TX2
TL
FSST
FSTD
CASH
T1 F $1.00
T2
$2.00
F $3.00
$1.00
$0.04
$2.00
$0.10
$6.14 — Subtotal
$4.04 — Food stamp subtotal
$2.00 — Food stamp tendered
$4.14
Mixed food stamp/cash change
Example 1
OPERATION
Dept. 1
$1.00
Item 1 —————————
Taxable
1, F/S
—————————————
Dept. 2
$2.00
Item 2 —————————
Taxable
2, F/S
—————————————
Dept. 3
$3.00
Item 3 —————————
Taxable
F/S
—————————————
Payment Food stamp $7.00
1-!
K2-"
K3-#
J
I
7-I
RECEIPT
REG 03-04-2000 14:35
C01
MC#01
000120
1 DEPT01
1 DEPT02
1 DEPT03
TA1
TX1
TA2
TX2
TL
FSST
FSTD
CG
T1 F $1.00
T2 F $2.00
F $3.00
$1.00
$0.04
$2.00
$0.10
$6.14 —
$6.14 —
$7.00 —
$0.86 —
Subtotal
Food stamp subtotal
Food stamp tendered
Cash change
Advanced Operations
The change in food stamp transactions is automatically calculated as cash for amounts of $1.00 or less, and as
food stamps for amounts greater than $1.00.
Example 2
OPERATION
Dept. 1
$2.00
—————————
Taxable
1, F/S
—————————————
Payment Food stamp $5.00
Item
2-!
J
I
5-I
RECEIPT
REG 03-04-2000 14:40
C01
MC#01
000121
1 DEPT01
TA1
TX1
TL
FSST
FSTD
FSCG
CG
T1 F $2.00
$2.00
$0.08
$2.08
$2.08
$5.00
$2.00
$0.92
In the above example, the total amount of change due is $2.92; $2.00 in food stamps and $0.96 in cash.
TK-6000/6500 User’s Manual
65
Advanced Operations
Mixed food stamp/cash change (continued…)
Example 3
OPERATION
Dept. 1
$2.00
Item 1 —————————
Taxable
1, F/S
—————————————
$0.50
Dept. 4
Item 2 —————————
Taxable
No
—————————————
Payment Food stamp $5.00
RECEIPT
2-!
50$
J
I
5-I
REG 03-04-2000 14:45
C01
MC#01
000122
1 DEPT01
1 DEPT04
TA1
TX1
TL
FSST
FSTD
FSCG
CG
T1 F $1.00
$0.50
$2.00
$0.08
$2.58
$2.08
$5.00
$2.00
$0.42
When food stamp items are included in a transaction, the amount of change due in cash is applied as a cash
amount tendered for cash (nonfood stamp) items. In this example, the $0.50 purchased (department 4) is
automatically deducted from the $0.92 cash due in change from the food stamp purchase (department 4).
Example 4
OPERATION
Dept. 1
$1.00
Item 1 —————————
Taxable
1, F/S
—————————————
Dept. 2
$2.00
Item 2 —————————
Taxable
2
—————————————
Dept. 3
$3.00
Item 3 —————————
Taxable
No
—————————————
Food stamp $5.00
Payment —————————
Cash
$4.14
RECEIPT
1-!
2-"
3-#
J
5-I
a
REG 03-04-2000 14:50
C01
MC#01
000123
1 DEPT01
1 DEPT02
1 DEPT03
TA1
TX1
TA2
TX2
TL
FSST
FSTD
FSCG
CASH
T1 F $1.00
T2
$2.00
$3.00
$1.00
$0.04
$2.00
$0.10
$6.14
$1.04
$5.00
$3.00
$4.14
The following calculation is performed internally to apply the cash change due on the food stamp transaction to
the balance due of the cash transaction.
Price items:
Tax:
Total due:
Amount tendered:
Amount due:
Change amount due:
Total:
66
Food stamp transaction
$1.00
$0.04
$1.04
$5.00 (food stamp)
$1.04
$3.00 (food stamp), $0.96 (cash)
Cash transaction
$5.00
$0.10
$5.10
$4.14 (cash), $0.96 (change from food stamp)
$5.10
Food stamp registration (Illinois rule)
No change due
Example 1
OPERATION
1-!
2-!
3-$
J
6-I
I
REG 03-04-2000 14:55
C01
MC#01
000124
1 DEPT01
1 DEPT01
DEPT04
TL
FSST
FSTD
T1 F $1.00
T1 F $2.00
F $3.00
$6.00
$6.00
$6.00
Advanced Operations
Dept. 1
$1.00
Item 1 —————————
Taxable
1, F/S
—————————————
$2.00
Dept. 1
Item 2 —————————
Taxable
1, F/S
—————————————
$3.00
Dept. 4
Item 3 —————————
Taxable
F/S
—————————————
Payment Food stamp $6.00
RECEIPT
Example 2
OPERATION
Dept. 1
$2.00
Item 1 —————————
Taxable
1, F/S
—————————————
$3.00
Dept. 1
Item 2 —————————
Taxable
1, F/S
—————————————
$4.00
Dept. 4
Item 3 —————————
Taxable
1, F/S
—————————————
Food stamp $5.00
Payment —————————
Cash
$4.16
TK-6000/6500 User’s Manual
2-!
3-!
4-$
J
5-I
I
a
RECEIPT
REG 03-04-2000 15:00
C01
MC#01
000125
1 DEPT01
1 DEPT01
1 DEPT04
FSST
FSTD
TA1
TX1
CASH
T1 F $2.00
T1 F $3.00
F $4.00
$9.00
$5.00
$4.00
$0.16
$4.16
67
Advanced Operations
No change due (continued…)
Example 3
OPERATION
Dept. 1
$2.00
Item 1 —————————
Taxable
1, F/S
—————————————
$3.00
Dept. 2
Item 2 —————————
Taxable
2, F/S
—————————————
Food stamp $1.00
Payment —————————
Cash
$4.14
2-!
3-"
J
I
1-I
a
RECEIPT
REG 03-04-2000 15:05
C01
MC#01
000126
1 DEPT01
1 DEPT02
FSST
FSTD
TA1
TX1
TA2
TX2
CASH
T1 F $2.00
T2 F $3.00
$5.00
$1.00
$1.00
$0.04
$2.00
$0.10
$4.14
If the total of the food stamps tendered is less than the food stamp total, the food stamp tendered amount is
deducted from the taxable 1 and 2 amount.
Example 4
OPERATION
Dept. 1
$1.00
Item 1 —————————
Taxable
1, F/S
—————————————
$5.00
Dept. 2
Item 2 —————————
Taxable
2, F/S
—————————————
Food stamp $4.00
Payment —————————
Cash
$2.05
1-!
5-"
J
I
4-I
a
In this example, the result of the taxable 1 amount is “0”.
68
RECEIPT
REG 03-04-2000 15:10
C01
MC#01
000127
1 DEPT01
1 DEPT02
FSST
FSTD
TA2
TX2
CASH
T1 F $1.00
T2 F $5.00
$6.00
$4.00
$1.00
$0.05
$2.05
Mixed food stamp/cash change
Example 1
OPERATION
Dept. 1
$1.50
Item 1 —————————
Taxable
1, F/S
—————————————
$2.00
Dept. 1
Item 2 —————————
Taxable
1, F/S
—————————————
$3.00
Dept. 4
Item 3 —————————
Taxable
F/S
—————————————
Payment Food stamp $10.00
150!
2-!
3-$
J
10-I
I
RECEIPT
REG 03-04-2000 15:15
C01
MC#01
000128
1 DEPT01
1 DEPT01
1 DEPT04
TL
FSST
FSTD
FSCG
CG
T1 F $1.50
T1 F $2.00
F $3.00
$6.50
$6.50
$10.00
$3.00
$0.50
The change in food stamp transactions is automatically calculated as cash for amount of $1.00 or less, and as
food stamps for amounts greater than $1.00. In the above example, the total amount of change due is $3.50
($3.00 in food stamps and $0.50 in cash).
OPERATION
Dept. 1
$2.00
—————————
Taxable
1, F/S
—————————————
Payment Food stamp $5.00
Item
2-!
J
5-I
I
TK-6000/6500 User’s Manual
Advanced Operations
Example 2
RECEIPT
REG 03-04-2000 15:20
C01
MC#01
000129
1 DEPT01
TL
FSST
FSTD
FSCG
T1 F $2.00
$2.00
$2.00
$5.00
$3.00
69
Advanced Operations
Mixed food stamp/cash change (continued…)
Example 3
OPERATION
Dept. 1
$2.00
Item 1 —————————
Taxable
1, F/S
—————————————
$1.20
Dept. 1
Item 2 —————————
Taxable
1, F/S
—————————————
$0.30
Dept. 3
Item 3 —————————
Taxable
1
—————————————
PaymentFood stamp $5.00
2-!
120!
30#
J
5-I
I
RECEIPT
REG 03-04-2000 15:25
C01
MC#01
000130
1 DEPT01
1 DEPT01
1 DEPT03
TA1
TX1
TL
FSST
FSTD
FSCG
CG
T1 F $2.00
T1 F $1.20
T1
$0.30
$0.30
$0.01
$3.51
$3.20
$5.00
$1.00
$0.49
When food stamp items are included in a transaction, the amount of change due in cash is applied as a cash
amount tendered for cash (nonfood stamp) items. In this example, the $0.30 purchase is automatically deducted
from the $0.80 cash due in change from the food stamp purchase.
Example 4
OPERATION
Dept. 1
$1.00
Item 1 —————————
Taxable
1, F/S
—————————————
$2.50
Dept. 1
Item 2 —————————
Taxable
1, F/S
—————————————
$5.00
Dept. 3
Item 3 —————————
Taxable
No
—————————————
Food stamp $5.00
Payment —————————
Cash
$4.50
1-!
250!
5-#
J
5-I
I
a
RECEIPT
REG 03-04-2000 15:30
C01
MC#01
000131
1 DEPT01
1 DEPT01
1 DEPT03
FSST
FSTD
FSCG
CASH
T1 F $1.00
T1 F $2.50
$5.00
$3.50
$5.00
$1.00
$4.50
The following calculation is performed internally to apply the cash change due on the food stamp transaction to
the balance due of the cash transaction.
Food stamp transaction
Cash transaction
Price items:
$3.50
$5.00
Tax:
$0.00
$0.00
Total due:
$3.50
$5.00
Amount tendered:
$5.00 (food stamp)
$4.50 (cash), $0.50 (change from food stamp)
Amount due:
$3.50
Change amount due: $1.00 (food stamp), $0.50 (cash)
Total:
$5.00
70
Mixed food stamp/cash change (continued…)
Food stamp + Taxable 1 + Taxable 2
When food stamps are received as partial tender for items preset with the status “food stamp”, “taxable 1”, and
“taxable 2”, the calculation are performed using one of the two cases described in this section. The case used
depends on the food stamp amount received as partial tender.
Case 1
This case is used when the total amount of the items preset with the status “food stamp”, “taxable 1”, and
“taxable 2” is greater than or equal to the food stamp amount received as partial tender. Case 1 subtracts the
food stamp amount tendered from both the taxable 1 amount and taxable 2 amount.
Example 5
OPERATION
2-!
3-"
T2-!
J
2-I
I
a
REG 03-04-2000 15:35
C01
MC#01
000132
1 DEPT01
1 DEPT02
1 DEPT01
FSST
FSTD
TA1
TX1
TA2
TX2
CASH
T1 F $2.00
T2 F $3.00
T12F $2.00
$7.00
$2.00
$2.00
$0.08
$3.00
$0.15
$5.23
Advanced Operations
Dept. 1
$2.00
Item 1 —————————
Taxable
1, F/S
—————————————
$3.00
Dept. 2
Item 2 —————————
Taxable
2, F/S
—————————————
$2.00
Dept. 1
Item 3 —————————
Taxable 1/2, F/S
—————————————
Food stamp $2.00
Payment —————————
Cash
$5.23
RECEIPT
In this example, the food stamp received as partial tender is $2.00, so that amount is deducted from both the
taxable 1 amount and taxable 2 amount. This means that the remaining taxable 1 amount is $2.00, while the
remaining taxable 2 amount is $3.00.
TK-6000/6500 User’s Manual
71
Advanced Operations
Mixed food stamp/cash change (continued…)
Case 2
This case is used when the total amount of the items preset with the status “food stamp”, “taxable 1”, and
“taxable 2” is less than or equal to the food stamp amount received as partial tender.
Example 6
OPERATION
Dept. 1
$2.00
Item 1 —————————
Taxable
1, F/S
—————————————
$3.00
Dept. 2
Item 2 —————————
Taxable
2, F/S
—————————————
$2.00
Dept. 1
Item 3 —————————
Taxable 1/2, F/S
—————————————
Food stamp $4.00
Payment —————————
Cash
$3.05
72
2-!
3-"
T2-!
J
4-I
I
a
RECEIPT
REG 03-04-2000 15:40
C01
MC#01
000133
1 DEPT01
1 DEPT02
1 DEPT01
FSST
FSTD
TA2
TX2
CASH
T1 F $2.00
T2 F $3.00
T12F $2.00
$7.00
$4.00
$1.00
$0.05
$3.05
Electronic benefits transfer
In addition to standard food stamp tender finalizations, this model also allows finalization for tenders electronic
benefits transfer (EBT) card.
EBT tenders can be accepted for New Jersey rule or Illinois rule food stamp tenders, as well as for food stamp
tenders that do not follow these rules.
About mixed EBT card tenders
When the register is programmed to prohibit an EBT amount tendered that exceeds the food stamp subtotal,
nonfood stamp items cannot be paid for using an EBT card. In this case, the following applies:
• ST – (EBT/TEND – FS/ST) = Balance due (the remaining balance due must be finalized using another finalize key.)
When the register is programmed to allow an EBT amount tendered that exceeds the food stamp subtotal,
nonfood stamp items can be paid for using an EBT card. In this case, there are two possible situations:
• ST > EBT/TEND
ST – (EBT/TEND – FS/ST) = Balance due (the remaining balance due must be finalized using another finalize key.)
• EBT/TEND > or = ST
EBT/TEND – ST = cash change
No change due
Example 1
OPERATION
TK-6000/6500 User’s Manual
1-!
2-"
3-#
J
EBT
6-B
B
REG 03-04-2000 15:45
C01
MC#01
000134
1 DEPT01
1 DEPT02
1 DEPT03
TL
FSST
EBTTD
Advanced Operations
Dept. 1
$1.00
Item 1 —————————
Taxable
1, F/S
—————————————
$2.00
Dept. 2
Item 2 —————————
Taxable
2, F/S
—————————————
$3.00
Dept. 3
Item 3 —————————
Taxable
F/S
—————————————
$6.00
Payment EBT
RECEIPT
T1 F $1.00
T2 F $2.00
F $2.00
$6.00
$6.00
$6.00
73
Advanced Operations
Example 2
OPERATION
Dept. 1
$1.00
Item 1 —————————
Taxable
1, F/S
—————————————
$2.00
Dept. 2
Item 2 —————————
Taxable
1, F/S
—————————————
$3.00
Dept. 3
Item 3 —————————
Taxable
1
—————————————
EBT
$5.00
Payment —————————
Cash
$1.12
1-!
2-"
3-#
J
EBT
5-B
B
F
RECEIPT
REG 03-04-2000 15:50
C01
MC#01
000135
1 DEPT01
1 DEPT02
1 DEPT03
FSST
EBTTD
TA1
TX1
CASH
T1 F $1.00
T1 F $2.00
T1
$3.00
$3.00
$5.00
$3.00
$0.12
$1.12
Change due
OPERATION
Dept. 1
$1.00
Item 1 —————————
Taxable
1, F/S
—————————————
$1.20
Dept. 2
Item 2 —————————
Taxable
1, F/S
—————————————
$0.30
Dept. 3
Item 3 —————————
Taxable
1
—————————————
$5.00
Payment EBT
1-!
120"
30#
J
EBT
5-B
B
RECEIPT
REG 03-04-2000 15:55
C01
MC#01
000136
1 DEPT01
1 DEPT02
1 DEPT03
TA1
TX1
TL
FSST
EBTTD
CG
T1 F $1.00
T1 F $1.20
T1
$0.30
$0.30
$0.01
$2.51
$2.20
$5.00
$2.49
Tips
Example
OPERATION
Unit price $3.00
Item 1 —————————
Dept.
1
—————————————
Unit price $5.00
Item 2 —————————
Dept.
2
—————————————
$0.80
Tip
Amount
—————————————
$10.00
Payment Cash
74
3-!
5-"
s
TIP
B
80B
10-F
RECEIPT
REG 03-04-2000 16:00
C01
MC#01
000137
1 DEPT01
1 DEPT02
TIP
TL
CASH
CG
•3.00
•5.00
•0.80
$8.80
$10.00
$1.20
Inputting the number of customers
Example 1
OPERATION
CST
2B
B
15-!
5-"
s
F
REG 03-04-2000 16:05
C01
MC#01
000138
CT
1 DEPT01
1 DEPT02
TL
CASH
2
•15.00
•5.00
•20.00
•20.00
Example 2
You can only use the following operation to re-input the number of customers when <CUSTOMER> (customer
number key) is preset to allow re-input. When programming prohibits re-input of the number of customers, this
operation causes an error.
OPERATION
RECEIPT
CST
3B
B
15-!
5-"
CST
B
2B
s
20-F
REG 03-04-2000 16:10
C01
MC#01
000139
CT
1 DEPT01
1 DEPT02
CT
TL
CASH
3
•15.00
•5.00
2
•20.00
•20.00
You can re-input the number of customers either immediately after the initial input or during later registration.
Example 3
You can use the following operation to add customers to an original number of customers input (when addition
to the number of the customer is allowed).
OPERATION
RECEIPT
CST
3B
B
15-!
5-"
CST
B
2B
s
20-F
TK-6000/6500 User’s Manual
REG 03-04-2000 16:15
C01
MC#01
000140
CT
1 DEPT01
1 DEPT02
CT
TL
CASH
3
•15.00
•5.00
5
•20.00
•20.00
75
Advanced Operations
Unit price $15.00
Item 1 —————————
Dept.
1
—————————————
Unit price $5.00
Item 2 —————————
Dept.
2
—————————————
Customer Number
2
—————————————
$20.00
Payment Cash
RECEIPT
Advanced Operations
Text recall
This procedure is used to recall text by inputting the address where the text is stored. The recalled text is
printed on the receipt and journal.
Example
OPERATION
RECEIPT
Unit price $46.00
Item 1 —————————
Dept.
1
—————————————
Unit price $10.00
Item 2 —————————
Dept.
2
—————————————
$56.00
Payment Cash
—————————————
Text 1 MEDIUM SIZE
—————————————
Text 2
SMALL SIZE
46-!
TEXT
B
1B
RECALL
10-"
TEXT
B
2B
RECALL
s
F
REG 03-04-2000 16:20
C01
MC#01
000141
CT
3
1 DEPT01
•46.00
MEDIUM SIZE
1 DEPT02
•10.00
SMALL SIZE
TL
•56.00
CASH
•56.00
Temporarily releasing compulsion
<OPEN 2> (open 2 key) can be programmed to release specific compulsion.
Example 1
OPERATION
RECEIPT
Unit price $10.00
—————————
Dept.
1
—————————————
$10.00
Payment Check
—————————————
Validation compulsory
Item
10-!
10-k
2-"
REG 03-04-2000 16:25
C01
MC#01
000142
1 DEPT01
TL
CHECK
•10.00
•10.00
•10.00
Validation compulsory (E041)
OPEN
B
2
Validation compulsory
is temporarily released.
Example 2
OPERATION
RECEIPT
10-! REG 03-04-2000 16:30
Input customer No. compulsory
————————————— Input customer No. compulsory
C01
MC#01
000143
Unit price $10.00
(E019)
Item —————————
OPEN
1 DEPT01
•10.00
B
2
Dept.
1
TL
•10.00
—————————————
$10.00 Compulsory is temporarily released.
CHECK
•10.00
Payment Check
—————————————
10-!
10-k
76
Printing slip
•
•
•
•
•
•
To perform batch printing on the slip printer, you must first use the memory allocation operation (see program
5 mode in the dealer’s manual) to reserve slip buffer memory. The capacity of the slip buffer memory is
determined by the number of units of slip buffer memory reserved by the memory allocation operation.
The register can be programmed to check the status of the registration buffer memory whenever slip batch
printing is performed, and sound an alarm when the buffer memory is almost full. The alarm sounds when there
are 12 lines or less remaining, and once it starts to sound, the only operation you can perform is the cancel
operation or operations using one of the following keys.
<CA/AMT TEND> (cash/amount tendered key) operation
<CH> (charge key) operation
<CHK/TEND> (check tendered key) operation
<DEPOSIT> (deposit key) operation
<NEW BALANCE> (new balance key) operation
<SUBTOTAL> (subtotal key) operation
You must perform one of above operations when the registration buffer alarm sounds. Any other operations
results in an error.
The cash register can be connected to the optional SP-1300 slip printer, which features an automatic feed
function and automatic back feed function.
• Automatic feed function
This function makes it possible to program the number of line feeds that should be inserted from the normal
print start position before starting slip printing of a new slip. Even if line feeds are programmed for this
function, they are not inserted for validation printing, check endorsement printing, and check printing
performed using the slip printer. Note also that line feeds are not inserted automatically at the beginning of a
second slip when the transaction requires printing that extends from one slip to another.
• Automatic back feed function
This function performs automatic back feed following slip printing, validation printing, and endorsement
printing on the slip printer. The slip paper is released once the back feed operation is complete.
• Manual feed function
<SLIP FEED/RELEASE> (slip feed/release key: assigned to the register’s keyboard using the program 4 mode)
can be used for manual feed of the slip paper. You perform manual feed by inputting a value for the number of
lines (up to two digits in the range of 1 to 99) and then press <SLIP FEED/RELEASE>.
• Manual back feed function
<SLIP BACK FEED/RELEASE> (slip back feed/release key: assigned to the register’s keyboard using the
program 4 mode) can be used for manual back feed of the slip paper. Manual back feed can be performed by
inputting a value for the number of lines (up to two digits in the range of 1 to 99) and then press <SLIP BACK
FEED/RELEASE>.
You can print slips using automatic or manual batch printing. The slip print operation can be performed in
REG1, REG2, and RF modes only.
Finalizing a registration without inserting a slip paper into the slip printer when the register is programmed as
“slip paper insertion into slip printer compulsory before finalizing registration” produces an error.
TK-6000/6500 User’s Manual
77
Advanced Operations
Printing slips
Advanced Operations
To perform auto batch printing 1
Finalization
Registration
Print receipt/journal.
Insert a slip paper
into the slip printer.
Print receipt/journal.
Print slip.
Remove slip paper.
To perform auto batch printing 2
SLIP
PRINT
Registration/
finalization
Print receipt/journal.
Insert a slip paper
into the slip printer.
Print slip.
Remove slip paper.
About the maximum number of slip lines
You can program the maximum number of lines that can be printed on a slip. Once you do, any attempt to
exceed the preset maximum results in an error. When such an error occurs, press <C>, change slip paper and
press <SLIP PRINT> to restart printing.
Check tracking systems
Check tracking system
With the check tracking system, the amount, check number, number of slip print lines, store number, date/time
and registration detail data are stored in two files (check tracking index file and check tracking detail file).
• Check tracking detail file and index file are cleared by the following timing:
1.The check is cleared after printing finalized data on slip or guest check receipts, or the check is also cleared
when the new or old check operation is made.
2.The check is cleared after printing finalized data on slip or guest check receipt, or check is also cleared when
the same finalized check number is assigned in new check operation.
You can select one of these options by programming.
• Auto new balance function
The register can be programmed so that whenever a clerk (by clerk key) signs off while a check is open, a
<NEW BALANCE> operation is automatically performed to temporarily finalize the open check.
• You can specify a range of checks that can be opened by each clerk. Once you do, any attempt by a clerk to
open a check using a number that is not within his specified range results in an error.
• Either of the following two operations can be used to correct input of a wrong check number.
<NEW CHECK>
Re-input the correct check number, or cancel the original check number, issue a receipt, and then re-input the
correct check number.
<OLD CHECK>, <NEW/OLD>
Temporary finalize the original check number, issue a receipt, and then re-input the correct check number.
78
Opening a check
Example
OPERATION
Check#
1234
—————————————
Table#
33
—————————————
$10.00
Dept. 1
Item 1 —————————
Quantity
2
—————————————
$20.00
Dept. 2
Item 2 —————————
Quantity
2
—————————————
$30.00
Dept. 3
Item 3 —————————
Quantity
1
RECEIPT
NEW
1234B
B
CHECK
TABLE
B
33B
#
10-!
!
20-"
"
30-#
Insert slip
REG 03-04-2000 16:35
C01
MC#01
000144
CHECK No.1234
1
1
1
1
1
TBL-#
000033
DEPT01
•10.00
DEPT01
•10.00
DEPT02
•20.00
DEPT02
•20.00
DEPT03
•30.00
+
•0.50
SRVC TL •90.50
NB
B
Remove slip
Press <NEW BALANCE> to temporarily close the transaction. If you want to finalize a check immediately, use
<CASH>, <CHARGE>, <CREDIT> or <CHECK>.
Advanced Operations
Adding to a check
Example
OPERATION
Check#
1234
—————————————
Table#
33
—————————————
$30.00
Dept. 1
Item 1 —————————
Quantity
1
—————————————
$10.00
Dept. 2
Item 2 —————————
Quantity
1
RECEIPT
OLD
1234B
B
CHECK
30-!
10-"
Insert slip
NB
B
Remove slip
REG 03-04-2000 16:40
C01
MC#01
000145
TABLE No.000033
CT
1
CHECK No.1234
ST
•90.50
1 DEPT01
•30.00
1 DEPT02
•10.00
+
•0.50
SRVC TL
•131.00
• The table number is stored in the check tracking index memory so its input is not required in this operation
even if table number input is preset as compulsory. Table number input after inputting the check number may
be performed, however, without generating an error.
• Once a check is opened under a number in a certain mode (REG1 or REG2), the same mode must be used to
make additions to the check.
TK-6000/6500 User’s Manual
79
Advanced Operations
Issuing a guest receipt
The following operation can be used to print out the balance of a temporarily finalized check.
Example
OPERATION
RECEIPT
GUEST
1234B
B
RECEIPT
Input the number of check you
want.
REG 03-04-2000 16:45
C01
MC#01
000146
TABLE No.000033
CT
1
CHECK No. 1234
1
1
1
1
1
DEPT01
DEPT01
DEPT02
DEPT02
DEPT03
+
1 DEPT01
1 DEPT02
+
SRVC TL
•10.00
•10.00
•20.00
•20.00
•30.00
•0.50
•30.00
•10.00
•0.50
•131.00
Closing a check memory
Example
OPERATION
OLD
1234B
B
CHECK
150-F
RECEIPT
REG 03-04-2000 16:50
C01
MC#01
000147
TABLE No.000033
CT
1
CHECK No.1234
ST
CASH
CG
80
•131.00
•150.00
•19.00
SLIP
REG
03-04-2000
C01
MC#01
TABLE No.000033
CHECK No. 1234
1
1
1
1
1
#13
#17
DEPT01
DEPT01
DEPT02
DEPT02
DEPT03
+
SRVC TL
1 DEPT01
1 DEPT02
+
SRVC TL
TL
CASH
CG
16:50
000147
CT
1
•10.00
•10.00
•20.00
•20.00
•30.00
•0.50
•90.50
•30.00
•10.00
•0.50
•131.00
•131.00
•150.00
•19.00
New/old check key operation
NEW/
3456B
B
OLD
Input a check number and press
<NEW/OLD>.
10-!
20-"
NB
B
Advanced Operations
Example 1
When a check number is input and <NEW/OLD> is pressed, the key works as a new check key function if
there is no matching check number in the check tracking memory.
OPERATION
RECEIPT
REG 03-04-2000 16:55
C01
MC#01
000148
CHECK No.3456
1 DEPT01
•10.00
1 DEPT02
•20.00
+
•0.50
SRVC TL •30.50
Example 2
When a check number is input and <NEW/OLD> is pressed, the key works as an old check key if there is
matching check number in the check tracking memory.
OPERATION
RECEIPT
NEW/
3456B
B
OLD
31-F
REG 03-04-2000 17:00
C01
MC#01
000149
CT
1
CHECK No.3456
ST
TL
CASH
CG
TK-6000/6500 User’s Manual
•30.50
•30.50
•31.00
•0.50
81
Advanced Operations
Add check
This operation lets you combine the amounts of more than one check into a single check.
Example
Registration for check number 1234
OPERATION
Original check
Check#
1234
—————————————
$10.00
Dept. 1
Item 1 —————————
Quantity
1
—————————————
$20.00
Dept. 2
Item 2 —————————
Quantity
1
NEW
1234B
B
CHECK
TABLE
33B
#
10-!
20-"
NB
B
Registration for check number 3456
OPERATION
Added check
Check#
3456
—————————————
$30.00
Dept. 1
Item —————————
Quantity
1
NEW
3456B
B
CHECK
30-!
NB
B
Registration for check number 1234
OPERATION
Check No. :
1234
Check No. :
3456
OLD
1234B
CHECK
ADD
B
3456B
CHECK
NB
B
RECEIPT
REG 03-04-2000 17:05
C01
MC#01
000150
CHECk No.1234
TBL-#
000033
1 DEPT01
•10.00
1 DEPT02
•20.00
+
•0.50
SRVC TL •30.50
RECEIPT
REG 03-04-2000 17:10
C01
MC#01
000151
CHECK No.3456
1 DEPT01
•30.00
+
•0.50
SRVC TL •30.50
RECEIPT
REG 03-04-2000 17:15
C01
MC#01
000152
TABLE No.000033
CT
1
CHECK No.1234
ST
•30.50
ADD CHK
3456
ST
•30.50
+
•0.50
SRVC TL •61.50
82
Separate check
This operation makes it possible to split a single check into separate checks.
Example
Separated check
Original check
Check#
3456
—————————————
$10.00
Dept. 1
Item 1 —————————
Quantity
1
—————————————
$30.00
Dept. 3
Item 2 —————————
Quantity
1
—————————————
Payment Cash
$40.00
Check#
1234
—————————————
Dept. 1
$10.00
Item 1 —————————
Quantity
1
—————————————
$20.00
Dept. 2
Item 2 —————————
Quantity
1
—————————————
$30.00
Dept. 3
Item 3 —————————
Quantity
1
—————————————
$40.00
Dept. 4
Item 4 —————————
Quantity
1
RECEIPT
NEW
3456B
CHECK
This input of a temporary check
number can be skipped.
1234B
B
CHECK
REG 03-04-2000 17:20
C01
MC#01
000153
CHECK No.3456
Advanced Operations
OPERATION
SEPARATE
Input the original check number
by <SEP CHK>.
Display shows the 1st item
which will be separated.
B
CHECK
SEPARATE
After <SEP CHK>, this item is
separated.
SEP CHK
1234
1 DEPT01
•10.00
1 DEPT03
•30.00
ST
•40.00
CASH
•40.00
CG
•0.00
REVIEW
B
Display shows the 3rd item
which will be separated.
B
CHECK
NB
B
40-F
SEPARATE
TK-6000/6500 User’s Manual
83
Advanced Operations
Clerk transfer
This operation lets you change the clerk who is in charge of a specific open check number.
Example
To change the clerk for check number 1234 from clerk 1 to clerk number 4.
OPERATION
RECEIPT
Press this key if you do not want the clerk No.
or clerk secret No. to appear on the display.
o
CLK
1B
B
TRANS
Input the clerk No. of the clerk who is currently in
charge of check No. 1234 (target check).
OPE
4B
#
Input the clerk No. of the clerk who will take over
check No. 1234 (target check).
REG 03-04-2000 17:25
C01
MC#01
000154
CLK TRANS
C01
C04
1234
•60.50 — Check No./NB amount
-----------------------TL
•60.50
NEW
1234B
CHECK
Input the target check No. that is transferred from clerk 1 to 4.
You can use either <OLD CHK>, <NEW/OLD>.
Note that if you skip this step, all check Nos currently assigned
to clerk 1 are transferred to clerk 4.
CLK
B
TRANS
Table transfer
With this operation, you can change the number of a check.
Example 1
To change the check number 1234 to 1111 (which is newly opened).
OPERATION
Check No:
1234
NEW
1234B
CHECK
10-!
CHECK
B
1111B
TRANS
1111 <CHK TRN>
Input the new check No.
Check No:
1234
Check No:
1111
RECEIPT
REG 03-04-2000 17:30
C01
MC#01
000155
CHECK No.1234
1 DEPT01
•10.00
ST
•10.00
TBL TRANS
1111
SRVC TL •10.00
Example 2
To change the check number 3456 to 2222 (which has already been opened).
OPERATION
RECEIPT
Check No:
3456
Check No:
2222
1111 <CHK TRN>
Check No:
3456
Check No:
2222
Added
84
OLD
3456B
CHECK
10-!
CHECK
B
2222B
TRANS
REG 03-04-2000 17:35
C01
MC#01
000156
CHECK No.3456
ST
•10.00
1 DEPT01
•10.00
TBL TRANS
2222
SRVC TL •30.00
VAT breakdown printing
You can force printing of the VAT breakdown at the finalize stage, regardless of whether the cash register is
programmed to print or skip printing of the VAT breakdown.
Every time you want to have VAT breakdown, press <VAT>.
Example
OPERATION
RECEIPT
Dept. 1
$1.00
Item 1 —————————
1
Taxable
—————————————
PLU 1
($2.00)
Item 2 —————————
2
Taxable
—————————————
$3.00
Payment Cash
1-!
2+
V
F
REG 03-04-2000 17:40
C01
MC#01
000156
1 DEPT01
1 PLU0001
TA1
TX1
TA2
TX2
CASH
T1 •1.00
T2 •2.00
•0.90
•0.10
•1.90
•0.10
•3.00
Advanced Operations
Deposit registrations
Use the following procedures to register deposits.
Deposit from customer
OPERATION
Deposit
Cash
$50.00
DEPOSIT
50-B
B
–
F
RECEIPT
REG 03-04-2000 17:45
C01
MC#01
000157
DEPOTL
CASH
•50.00
•50.00
•50.00
Deposit from customer during sales transaction
OPERATION
Dept. 1
$10.00
Items —————————
$20.00
Dept. 2
—————————————
$20.00
Deposit
—————————————
$10.00
Payment Cash
TK-6000/6500 User’s Manual
10-!
20-"
DEPOSIT
B
20-B
+
F
RECEIPT
REG 03-04-2000 17:50
C01
MC#01
000158
1 DEPT01
1 DEPT02
DEPO+
TL
CASH
•10.00
•20.00
-20.00
•10.00
•10.00
85
Advanced Operations
Bill copy
Example 1
To issue a copy of a bill dated February 1, 2000 in the amount of $35.00 cash.
OPERATION
RECEIPT
BILL
02012000B
B
COPY
Enter date by date order.
35-F
*
*
*
*
BILL
BILL
BILL
BILL
TOP
TOP
TOP
TOP
MESSAGE
MESSAGE
MESSAGE
MESSAGE
1
2
3
4
*
* — Bill top message *1
*
*
REG 02-01-2000
C01
MC#01
* BILL COPY MESSAGE 1 *
* BILL COPY MESSAGE 2 * — Bill copy message *1
* BILL COPY MESSAGE 3 *
* BILL COPY MESSAGE 4 *
TA1
•35.00
TX1
•3.50 — Add-on tax amount
TL
•38.50
CASH
•38.50
*
*
*
*
BILL
BILL
BILL
BILL
BTM
BTM
BTM
BTM
MESSAGE
MESSAGE
MESSAGE
MESSAGE
1
2
3
4
*
* — Bill bottom message *1
*
*
*1
Programmable option
Note that you can finalize this operation using the cash amount tendered key.
Example 2
To issue a copy of a bill dated February 1, 2000 in the amount of Euro 30.00 cash (sub-currency).
OPERATION
RECEIPT
BILL
02012000B
B
COPY
q
30-F
*
*
*
*
BILL
BILL
BILL
BILL
TOP
TOP
TOP
TOP
MESSAGE
MESSAGE
MESSAGE
MESSAGE
1
2
3
4
*
* — Bill top message *1
*
*
REG 02-01-2000
C01
MC#01
* BILL COPY MESSAGE 1 *
* BILL COPY MESSAGE 2 * — Bill copy message *1
* BILL COPY MESSAGE 3 *
* BILL COPY MESSAGE 4 *
TA1
⁄27.28
TX1
⁄2.72 — Add-in tax amount
TL
⁄30.00
CASH
⁄30.00
*
*
*
*
86
BILL
BILL
BILL
BILL
BTM
BTM
BTM
BTM
MESSAGE
MESSAGE
MESSAGE
MESSAGE
1
2
3
4
* — Bill bottom message *1
*
*
*1
Programmable option
*
Programming to clerk
You can program up to 4-digit assigning number (clerk number), trainee status of clerk (i.e. training cashier)
and commission rate for each clerk.
Programming clerk number
To other clerk
6 3s 6
PGM
Mode switch
Rec. No.
1
:
10
{ }
07s
6::::a 6s
Clerk number
Programming trainee status
To other clerk
63s6
Mode switch
{ }
• Normal clerk = 0
• Training clerk = 1
Programming commission rate
To other clerk
PGM
63s6
Mode switch
{ }
Trainee
status
Clerk number
Record
No.
D4
D3
D2
Rec. No.
1
07s668s
:
10
D1
D6
00000
1
00000
2
00000
3
00000
4
00000
5
00000
6
00000
7
00000
8
00000
9
00000
10
00000
TK-6000/6500 User’s Manual
To the next clerk
6 : ~ : a6s
D8 ~ D1
Commission rate
Commission rate
Commission rate 1
Commission rate 2
Integer
Decimal
Integer
Decimal
D8
D7
D6
D5
D4
D3
D2
D1
87
Advanced Operations
PGM
To the next clerk
Rec. No.
1
07s667s6 : 0~0a6s
:
D6
10
Trainee status:
Advanced Operations
Character programming can be performed in two ways:
• Character keyboard programming (see page 93),
or
• Entering characters by code (see page 92).
Programming descriptors and messages
The following descriptors and messages can be programmed;
• Messages (Logo, commercial and bottom message)
• Clerk name
• PLU item descriptor
• Department key descriptor
• Machine number
Programming receipt message and clerk name
To other address code
To the next address code
6 2s 6 : : : : s 6 Characters 6 a 6 s
☞ See “Entering characters” section.
PGM
Mode switch
Address
code
Address code
Contents
Initial character
0107
Clerk 01
C01
0207
Clerk 02
C02
0307
Clerk 03
C03
0407
Clerk 04
C04
0507
Clerk 05
C05
0607
Clerk 06
C06
0707
Clerk 07
C07
0807
Clerk 08
C08
0907
Clerk 09
C09
1007
Clerk 10
C10
Machine number
Up to 8 characters can be set.
Address
code
Machine number
0191
88
Contents
Machine number
Initial character
MC#01
Yours
Address
code
0132
1st line of logo message
0232
2nd line of logo message
THANK
0332
3rd line of logo message
CALL
0432
4th line of logo message
0532
1st line of commercial message
0632
2nd line of commercial message
0732
3rd line of commercial message
0832
4th line of commercial message
0932
1st line of bottom message
1032
2nd line of bottom message
1132
3rd line of bottom message
1232
4th line of bottom message
1332
1st line of bill top message
1432
2nd line of bill top message
1532
3rd line of bill top message
1632
4th line of bill top message
1732
1st line of bill copy message
1832
2nd line of bill copy message
1932
3rd line of bill copy message
2032
4th line of bill copy message
2132
1st line of bill bottom message
2232
2nd line of bill bottom message
2332
3rd line of bill bottom message
2432
4th line of bill bottom message
2532
Post receipt message
2632
1st line of guest intermediate msg.
2732
2nd line of guest intermediate msg.
2832
3rd line of guest intermediate msg.
2932
4th line of guest intermediate msg.
3032
1st line of guest bottom msg.
3132
2nd line of guest bottom msg.
3232
3rd line of guest bottom msg.
3332
4th line of guest bottom msg.
3432
5th line of guest bottom msg.
3532
6th line of guest bottom msg.
3632
7th line of guest bottom msg.
3732
8th line of guest bottom msg.
3832
9th line of guest bottom msg.
3932
10th line of guest bottom msg.
TK-6000/6500 User’s Manual
Initial character
YOUR
Yours
RECEIPT
YOU
AGAIN
Advanced Operations
Contents
89
Advanced Operations
Programming department/transaction key descriptor
To another department/transaction key
6 2s 6
Characters
6
☞ See “Entering characters” section.
PGM
Mode switch
Contents
Department
Department
Department
Department
Department
Department
Department
Department
Transaction key
Initial character
Yours
DEPT01
DEPT02
DEPT03
DEPT04
DEPT05
DEPT06
DEPT07
DEPT08
01
02
03
04
05
06
07
08
Contents
Cash/Amount tendered
Charge
Check
Credit 1
Credit 2
Loan
Received on account
Paid out
Pick up
Minus
Discount
Refund
Correction
Validation
Receipt
Non add/No sale
VAT
Tax shift 1
Tax shift 2
Open
Clerk number
Subtotal
Receipt on/off
Multiplication/Date time
Multiplication/for/Date time
Two zero
Decimal point
Media change
90
Department key
Initial character
CASH
CHARGE
CHECK
CREDIT1
CREDIT2
LOAN
RC
PD
P.UP
%RF
CORR
VLD
RCT
#/NS
VAT
T/S1
T/S2
OPEN
CLK#
SUBTOTAL
RCT ON/OFF
X
QT
00
.
MEDIA CHG
Yours
6s
Programming flat-PLU descriptor
To another flat-PLU key
PGM
Mode switch
MENU 6
6 2s 6 Characters 6 B
☞ See “Entering characters” section.
flat-PLU key
6s
MENU to program to 2nd ~ 6th flat-PLU key.
Use B
Contents
Initial character
002
PLU 002
PLU0002
003
PLU 003
PLU0003
004
PLU 004
PLU0004
005
PLU 005
PLU0005
006
PLU 006
PLU0006
007
PLU 007
PLU0007
008
PLU 008
PLU0008
009
PLU 009
PLU0009
010
PLU 010
PLU0010
011
PLU 011
PLU0011
012
PLU 012
PLU0012
013
PLU 013
PLU0013
014
PLU 014
PLU0014
015
PLU 015
PLU0015
016
PLU 016
PLU0016
017
PLU 017
PLU0017
018
PLU 018
PLU0018
019
PLU 019
PLU0019
020
PLU 020
PLU0020
021
PLU 021
PLU0021
022
PLU 022
PLU0022
023
PLU 023
PLU0023
024
PLU 024
PLU0024
025
PLU 025
PLU0025
026
PLU 026
PLU0026
027
PLU 027
PLU0027
028
PLU 028
PLU0028
029
PLU 029
PLU0029
106
PLU 106
PLU0106
107
PLU 107
PLU0107
108
PLU 108
PLU0108
TK-6000/6500 User’s Manual
Yours
PLU0001
Advanced Operations
PLU No.
PLU 001
001
91
Advanced Operations
Entering characters
In this section, the method to enter descriptors or messages (characters) to the cash register during
programming is described.
Characters are specified by character keyboard or by codes. In the first half of this section, inputting method by
character code is described. In the latter half, the usage of character keyboard is described.
Entering characters by code
Every time you enter a character, choose character codes by the character code list (below) and press the ^
key to settle it. After you complete entering characters, press the - key to fix them.
Example:
Input “
A
p
p
l
e
J
u
i
c
e
enter “ 255^65^ 112^ 112^ 108^ 101^ 32^ 74^ 117^ 105^ 99^ 101^ -
Character code list
Chara
Code
Chara
Code
Chara
Code
Code
Chara
Code
Space
32
0
48
!
33
1
49
@
64
P
80
A
65
Q
81
a
96
p
112
Ç
128
97
q
113
ü
"
34
2
50
B
66
R
129
82
b
98
r
#
35
3
51
C
67
S
114
é
130
83
c
99
s
115
â
$
36
4
52
D
68
131
T
84
d
100
t
116
ä
132
%
&
37
5
53
E
38
6
54
F
69
U
85
e
101
u
117
à
133
70
V
86
f
102
v
118
å
'
39
7
55
134
G
71
W
87
g
103
w
119
ç
135
(
40
8
)
41
9
56
H
72
X
88
h
104
x
120
ê
136
57
I
73
Y
89
i
105
y
121
ë
*
137
42
:
58
J
74
Z
90
j
106
z
+
122
è
138
43
;
59
K
75
[
91
k
107
{
123
ï
139
,
44
<
60
L
76
\
92
l
108
|
124
î
140
-
45
=
61
M
77
]
93
m
109
}
125
ì
141
.
46
>
62
N
78
^
94
n
110
~
126
Ä
142
/
47
?
63
O
79
_
95
o
111
127
Å
143
Chara
Code
Chara
Code
Chara
Code
Chara
Code
Chara
Code
Chara
Code
É
144
á
160
176
192
208
Ó
224
240
æ
145
í
161
177
193
209
ß
225
241
Æ
146
ó
162
178
194
Ê
210
Ô
226
242
ô
147
ú
163
179
195
Ë
211
Ò
227
243
ö
148
ñ
164
180
196
È
212
õ
228
¶
244
ò
149
Ñ
165
Á
181
197
⁄
213
Õ
229
§
245
û
150
ª
166
Â
182
ã
198
Í
214
µ
230
246
ù
151
º
167
À
183
Ã
199
Î
215
231
247
ÿ
152
¿
168
©
184
200
Ï
216
232
248
Ö
153
®
169
185
201
217
Ú
233
¨
249
Ü
154
170
186
202
218
Û
234
•
250
ø
155
171
187
203
219
Ù
235
251
£
156
188
204
220
236
252
Ø
157
¡
189
205
221
237
253
ƒ
92
Code Chara
Code Chara
172
173
¢
158
«
174
¥
159
»
175
190
191
206
¤
207
Chara
Ì
«
222
238
223
239
Chara Code
254
Double
size
255
”,
”
Using character keyboard
Example:
Input “
A
p
p l e
enter “DBL”“A” “SHIFT”“p” “p” “l” “e” “SPACE”
RECEIPT
FEED
7
JOURNAL
FEED
Â
â
009
Á
008
007
006
7
8
Q
9
4
5
1
6
q
2
9
0
00
3
0
A
#-2
Ö
2
Ù
Ü
023
w
z
S
s
012
X
032
e
x
021
C
011
020
001
#-1
010
041
r
031
F
d
030
V
c
f
t
g
039
B
v
029
Æ
i
Ñ
6
b
038
Y
RECEIPT JOURNAL Û
û
FEED FEED
025
Î
Á
Í
Ó
á
008
À
Ò
à
007
Ä
005
q
004
A
9
I
O
*
068
u
058
J
h
057
M
n
047
i
m
K
056
087
(
0
<
065
106
096
)
-
086
o
075
.
097
'
P
076
k
107
±
_
L
066
,
088
¤
077
067
j
098
ß
078
8
059
y
¡
089
079
>>
¢
069
&
U
048
N
070
<<
060
7
^
080
6
w
a
s
011
X
z
002
1
e
028
x
010
CAP
SHIFT
001
009
5
5
d
037
f
c
V
6
046
055
l
>
;
084
/
083
105
=
_
095
p
[
094
:
?
'
093
+
104
]
{
085
074
064
g
037
v
7
y
h
b
N
<<
8
066
u
I
056
J
}
103
`
"
~
102
•
\
092
¥
101
4
073
082
091
100
n
>>
*
9
O
k
,
0
o
<
.
-
p
;
>
103
_
[
=
:
{
]
"
?
027
036
045
054
063
072
081
090
017
026
035
044
053
062
071
080
089
4
7
8
9
~
4
5
6
¥
1
2
3
099
DBL
1 Shift key
Pressing this key shifts the character from the uppercase
letter to lower case letter and returns to the uppercase
letter in sequence.
2 Left cursor key
This key is not used for this model.
3 Right cursor key
This key is not used for this model.
4 Double size letter key
Specifies that the next character you input to a double
size character.
You must press this key before each double size character.
5 Space key
Sets a space by depression.
6 CAP key
C
}
100
•
018
8
101
`
091
\
+
102
092
'
082
/
104
093
083
l
105
094
)
P
073
—>
_ ¿
ƒ
084
074
L
3
<—
±
095
'
085
(
2
ô
¡
086
075
064
m
096
¤
076
i
K
055
M
087
Ô
106
ß
077
¢
065
j
097
º
078
067
&
U
046
ª
â
088
¬
057
047
H
ÿ
068
õ
Â
079
y
Õ
048
t
B
Y
£
069
058
^
Y
ã
059
ñ
ø
070
060
æ
Ñ
038
028
Ã
049
%
G
å
Æ
039
r
061
050
ë
T
Ø
051
è
Ë
029
F
019
C
È
030
020
D
Å
040
$
R
é
”,
- .
DBL
019
ç
052
041
ï
4
021
012
ì
Ï
Ç
042
031
#
E
É
032
ü
3
í
Ì
022
@
S
003
Z
Ü
013
W
ù
ê
043
033
023
ö
014
2
!
ú
Ù
015
006
Q
Ú
Ê
034
024
ò
Ö
ä
1
ó
016
î
e
108
º
7
TK-6500
c
¿
099
¬
061
049
H
071
õ
090
ª
y
Õ
ñ
081
ÿ
062
ƒ
£
ø
072
ã
Y
æ
050
040
G
Ã
å
051
%
T
Å
063
052
ë
042
5
$
R
022
D
043
033
4
#
Ø
ç
053
è
Ë
ï
024
E
044
034
Ç
054
é
È
ì
Ï
ü
3
É
035
Ì
ù
ê
045
í
025
ö
@
W
Í
ú
026
ò
Ê
î
036
5
6CAP 1
SHIFT
B
•
a
002
Ò
013
003
Z
Ú
014
004
A
ó
015
!
005
8
Ó
Î
û
027
016
ä
1
C
Û
017
à
Ä
ô
018
á
À
Ô
u
Advanced Operations
TK-6000
J
“CAP”“J” “SHIFT”“u” “i” “c” “e”
098
9
0
00
0
•
A
#-2
B
#-1
7 Alphabet keys
Used input to characters.
8 Numeric keys
Used to enter program codes, memory number and
character codes.
9 Character fixed key
Enters when the alphabetic entry for a descriptor, name
or message has been completed.
0 Backspace/Character code fixed key
Registers one character with code (2 or 3 digit).
Clears the last input character, much like a back space
key. (Does not clear the double size letter key entry.)
A Program end key
Terminates the character programming.
B Character enter key
Registers the programmed characters.
Shifts the character to the upper case letter.
TK-6000/6500 User’s Manual
93
Advanced Operations
Printing read/reset reports
• Daily sales read report (“X1” mode)
You can print read reports at any time during the business day without affecting the data stored in the cash
register's memory.
• Daily sales reset report (“Z1” mode)
You should print reset reports at the end of the business day.
Important!
• The reset operation issues a report and also clears all sales data from the cash register's memory.
• Be sure to perform the reset operations at the end of each business day. Otherwise, you will not be
able to distinguish between the sales data for different dates.
To print the individual department, PLU/flat-PLU read report
This report shows sales for specific departments or PLUs/flat-PLUs.
OPERATION
X1
Mode switch
8
• Specifying a department
!, ", #~
• Specifying a PLU
1+ ~
• Specifying a flat-PLU
(, ) ~
8
s
After you finish to select items, press s to terminate.
94
REPORT
— Mode/date/time
X 03-04-2000 19:00
C01
MC#01
001234 — Clerk/Mc No./consecutive No.
X
INDIVIDUAL
— Read symbol/report title
—
DEPT01
38
8.13%
•257.53 —
—
PLU0001
17
0.53%
•17.00 —
—
#000001
#000123
17
-----------------------TL
88.61 —
•516.10 —
Department Name/No. of items
Sales ratio/amount
PLU Name/No. of items
Sales ratio/PLU amount
PLU random code
Total No. of items
Total amount
To print the financial read report
This report shows gross sales, net sales, cash in drawer and check in drawer.
OPERATION
REPORT
X
X1
Mode switch
8
Money declaration *1
• Main currency:
(Cash in drawer amount b, N or n)
• Sub currency:
(q cash in drawer amount b, N or n)
8
x or X
FLASH
— Read symbol/report title
Command code
Declared cash in drawer of main currency *1
Difference (= declared - accumulated) *1
Declared cash in drawer of sub currency *1
Difference (= declared - accumulated) *1
0000071 —
•6,919.04 —
•0.00 —
⁄187.67 —
-10.87 —
DECLA
EURO money
GRS
111.15 —
•7,054.14 —
No
120
—
•7,263.20 —
•6,919.04 —
⁄178.60 —
NET
CAID
CAID2
FSID
EBTTL
Gross No. of items
Gross amount
Net No. of customers
Net amount
Cash in drawer of main currency
Cash in drawer of sub currency
•172.85 — Food stamp in drawer
•6.00 — EBT in drawer
This report shows individual clerk totals.
OPERATION
X1/Z1
(read/reset)
Mode switch
8
Money declaration *1
• Main currency:
(Cash in drawer amount b, N or n)
• Sub currency:
(q cash in drawer amount b, N or n)
REPORT
Z
DECLA
EURO money
C01
GROSS
8
NET
8
CAID
CHID
RF
20017a
::::a
Enter the appricable clerk number.
CLEAR
8
s
CASHIER
C02
0001 — Read symbol/report title/reset counter
0020017 — Command code
•6,919.04 —
•0.00 —
⁄187.67 —
-10.87 —
............1 —
421.25 —
•2,872.28
No
111
—
•1,845.35
•1,057.14 —
•139.04
No
1
—
•1.00
No
5
—
•4.43
Declared cash in drawer of main currency *1
Difference (= declared - accumulated) *1
Declared cash in drawer of sub currency *1
Difference (= declared - accumulated) *1
Clerk name/drawer No.
Gross total
Net total
Cash in drawer
Refund mode
Clear key count
............1 — Clerk name/drawer No.
After you finish to select clerks, press s to terminate.
*1
Money declaration:
Count how much cash is in the drawer and input this amount (up to 10 digits).
The cash register will automatically compare the input with the cash in drawer in the memory and print the
difference between these two amounts.
Note that if money declaration is required by programming, you cannot skip this procedure.
TK-6000/6500 User’s Manual
95
Advanced Operations
To print the individual clerk read/reset report
Advanced Operations
To print the daily sales read/reset report
This report shows sales except for PLUs.
OPERATION
X1/Z1
(read/reset)
Mode switch
8
Money declaration *1
• Main currency:
(Cash in drawer amount b, N or n)
REPORT
-----------------------— Report title
Z
BATCH01
-----------------------Z
FIX
0001 — Fixed total report title/reset counter *4
0001011 — Report code
DECLA
EURO money
• Sub currency:
(q cash in drawer amount b, N or n)
8
F
96
GROSS
•6,919.04 —
•0.00 —
⁄187.67 —
-10.87 —
981.25
—
•6,574.40
NET
No
111
—
•7,057.14
CAID
•6,919.04 —
CHID
•139.04 —
CKID
•859.85 —
CRID(1)
•709.85 —
-----------------------RF
No
3
—
•10.22
—
CUST
CT
111
AVRG
•63.57 —
DC
•1.22 —
REF
•2.42 —
—
CLEAR
No
85
ROUND
•0.00 —
CANCEL
No
2
—
•12.97
-----------------------TA1
•2,369.69 —
TX1
•128.86 —
TA2
•2,172.96 —
TX2
•217.33 —
-----------------------GT1
•00000000125478.96 —
GT2
•00000000346284.23 —
GT3
•00000000123212.75 —
-----------------------Z
TRANS
0001 —
Declared cash in drawer of main currency *1
Difference (= declared - accumulated) *1
Declared cash in drawer of sub currency *1
Difference (= declared - accumulated) *1
Gross total *3
Net total *3
Cash in drawer *3
Charge in drawer *3
Check in drawer *3
Credit in drawer *3
Refund mode *3
Customer number *3
Average sales per customer *3
Discount total *3
Refund key *3
Clear key count *3
Rounding total *3
Cancellation *3
Taxable 1 amount *3
Tax 1 amount *3
Taxable 2 amount *3
Tax 2 amount *3
Grand total 1 *3
Grand total 2 *3
Grand total 3 *3
Function key report title/reset counter
0001012 —
362
—
•1,638.04
CH
No
56
•1,174.85
RC
No
4
•810.00
PD
No
5
•520.00
•5.00
CORR
No
14
•39.55
VLD
No
19
RCT
No
3
NS
No
5
-----------------------Z
DEPT
0001 —
0001015 —
Report code
DEPT01
8.13%
DEPT02
—
38
•257.53 —
183
•1,362.26
-----------------------TL
88.61 —
•1,916.10 —
-----------------------Z
CASHIER
0001 —
0001017 —
Department name/No. of items *2
Sales ratio/amount *2
C01
GROSS
Clerk name/drawer No.
NET
CAID
CHID
RF
CLEAR
C02
*1
*2
*3
*4
No
............1 —
421.25 —
•2,872.28
No
111
—
•1,845.35
•1,057.14 —
•139.04
No
1
—
•1.00
No
5
—
•4.43
Function key count/amount *2
Department report title/reset counter
Report code
Advanced Operations
CASH
Total No. of items
Total amount
Clerk report title/reset counter
Report code
Gross total
Net total
Cash in drawer
Refund mode
Clear key count
............1 — Clerk name/drawer No.
Money declaration:
Count how much cash is in the drawer and input this amount (up to 10 digits).
The cash register will automatically compare the input with the cash in drawer in the memory and print the
difference between these two amounts.
Note that if money declaration is required by programming, you cannot skip this procedure.
Zero totalled departments/functions (the amount and item numbers are both zero) are not printed.
These items can be skipped by programming.
The “*” symbol is printed on the reset report, memory overflow occurred in the counter/totalizer.
TK-6000/6500 User’s Manual
97
Advanced Operations
To print the PLU/flat-PLU read/reset report
This report shows sales for PLUs.
OPERATION
X1/Z1
(read/reset)
Mode switch
8
014F
REPORT
X
PLU
— Read symbol/report title
0000014 — Report code
—
PLU0001
17
0.53%
•17.00 —
—
#000001
PLU0100
42
4.03%
•69.00
#000100
-----------------------TL
188.61 —
•516.10 —
PLU name/No. of items
Sales ratio/PLU amount
PLU random code
Total No. of items
Total amount
To print the hourly sales read/reset report
This report shows hourly breakdowns of sales.
OPERATION
X1/Z1
(read/reset)
Mode switch
8
019F
98
REPORT
X
HOURLY
— Read symbol/report title
0000019 — Report code
—
00:00->01:00
—
CT
1
GROSS
•1.10 —
—
NET
No
1
1.90%
•1.20 —
23:00->00:00
CT
1
GROSS
•3.45
NET
No
1
3.90%
•3.59
-----------------------—
TL
CT
280
GROSS
•1,937.61 —
—
NET
No
25
•2,096.80 —
Time range
No. of customers
Gross sales amount
No. of receipt
Sales ratio/net sales amount
Total No. of customers
Gross total amount
Total No. of receipt
Net total amount
To print the monthly sales read/reset report
This report shows monthly breakdowns of sales.
OPERATION
X1/Z1
(read/reset)
Mode switch
8
020F
REPORT
X
MONTHLY
— Read symbol/report title
0001020 — Report code
1......
GROSS
NET
— Date of a month
Gross symbol/No. of items
Gross sales amount
Net symbol/No. of customers
Net sales amount
1236.76 —
•12,202.57 —
—
No
214
•12,202.57 —
31......
GROSS
Total symbol
Gross symbol/No. of items
Gross sales amount
Average daily gross sales
Net symbol/No. of customers
Net sales amount
Average daily net sales
Advanced Operations
2132
•14,187.57
NET
No
205
•13,398.76
-----------------------—
TL
GROSS
9746.63 —
•161,022.49 —
•16.52 —
—
NET
No 2351
•161,022.49 —
•68.49 —
To print the group read/reset report
This report shows PLU/subdepartment/department group totals.
OPERATION
X1/Z1
(read/reset)
Mode switch
8
016F
TK-6000/6500 User’s Manual
REPORT
X
GROUP
— Read symbol/report title
0001016 — Report code
GROUP01
203.25 —
33.87%
•1,108.54 —
GROUP02
183
40.58%
•1,327.80
GROUP03
12
0.40%
•13.25
GROUP99
13
0.54%
•17.80
-----------------------—
TL
862
•3,272.00 —
Group No./No. of items
Sales ratio/group amount
Group total No. of items
Group total amount
99
Advanced Operations
• Periodic sales read report (“X2” mode)
You can print read reports at any time during the business day without affecting the data stored in the cash
register's memory.
• Periodic sales reset report (“Z2” mode)
You should print reset reports at the end of the business day.
To print the periodic 1/2 sales read/reset reports
These reports show sales breakdowns of sales by any two kinds of period you want.
OPERATION
REPORT
CASH
X2/Z2
(read/reset)
Mode switch
8
1F
-----------------------— Report title
ZZ1
BATCH02
-----------------------ZZ1
FIX
0001 — Fixed total report title/reset counter
0001111 — Report code
GROSS
981.25
—
•6,574.40
NET
No
111
—
•7,057.14
CAID
•6,919.04 —
CHID
•139.04 —
CKID
•859.85 —
CRID(1)
•709.85 —
-----------------------RF
No
3
—
•10.22
—
CUST
CT
111
AVRG
•63.57 —
DC
•1.22 —
REF
•2.42 —
—
CLEAR
No
85
ROUND
•0.00 —
CANCEL
No
2
—
•12.97
-----------------------TA1
•2,369.69 —
TX1
•128.86 —
-----------------------ZZ1 TRANS
0001 —
0001112 —
*1
*2
Gross total *2
Net total *2
Cash in drawer *2
Charge in drawer *2
Check in drawer *2
Credit in drawer *2
Refund mode
*2
Customer number *2
Average sales per customer *2
Discount total *2
Refund key *2
Clear key count *2
Rounding total *2
No
362
— Function key count/amount *1
•1,638.04
CH
No
56
•1,174.85
VLD
No
19
RCT
No
3
NS
No
5
-----------------------ZZ1 DEPT
0001 — Department report title/reset counter
0001115 — Report code
—
38
•257.53 —
183
•1,362.26
-----------------------TL
88.61 —
•1,916.10 —
-----------------------ZZ1 CASHIER
0001 —
0001117 —
DEPT01
8.13%
DEPT02
C01
GROSS
NET
CAID
CHID
RF
Cancellation *2
CLEAR
Taxable 1 amount *2
Tax 1 amount *2
C02
............1 —
421.25 —
•2,872.28
No
111
—
•1,845.35
•1,057.14 —
•139.04
No
1
—
•1.00
No
5
—
•4.43
Department Name/No. of items *1
Sales ratio/amount *1
Total No. of items
Sales ratio/total amount
Clerk report title/reset counter
Report code
Clerk name/drawer No.
Gross total
Net total
Cash in drawer
Refund mode
Clear key count
............1 — Clerk name/drawer No.
Function key report title/reset counter
Report code
Zero totalled departments/functions (the amount and item numbers are both zero) are not printed.
These items can be skipped by programming.
100
To print other sales read/reset reports
The following reports can be issued.
Procedure
X1/Z1
X2/Z2
(read/reset)
Mode switch
6 Money declaration
6 : : ~ : :a
(if necessary)
Command code
Report/command code list
Fix totalizer *2
Transaction key
Subdepartment *1
PLU by record number (all)
best 50 (amount order)
best 50 (quantity order)
menu (1st)
menu (2nd) *1
menu (3rd) *1
menu (4th) *1
menu (5th) *1
menu (6th) *1
Command
code
11
12
13
14
60014
70014
81
82
83
84
85
86
Report name
Command
code
15
60015
70015
16
17
19
20
25
28
Department
best 50 (amount order)
best 50 (quantity order)
Group
Clerk *2
Hourly sales
Monthly sales
Open check
Table analysis
*1
Memory allocation is necessary.
*2
Input money in drawer, if the money decalration
is compulsory.
Advanced Operations
Report name
Reading the cash register's program
To print unit price/rate program (except PLU)
OPERATION
PGM
REPORT
P01.................... — Program read symbol
CASH
CHECK
%-
@100.00 — Transaction key unit price or rate
@1.00
@1.00
10%
8
DEPT01
s
DEPT02
0001-05 — Department descriptor/rec-#/file-#
@1.00 — Unit quantity/unit price
0002-05
@2.00
Mode switch
8
1s
TK-6000/6500 User’s Manual
1.2
1
101
Advanced Operations
To print key descriptor, name, message program (except PLU)
OPERATION
REPORT
PGM
Mode switch
8
2s
FIX
TRANS
PLU
8
s
0001-24
0002-24— Report header character
0003-24
0004-24
0001-29
0002-29— Batch X/Z character
0003-29
0004-29
P02.................... — Program read symbol
BATCH 01
BATCH 02
BATCH 03
GROSS
NET
CAID
CATL
0001-32
YOUR RECEIPT
— Receipt message
0002-32
THANK YOU
GT1
GT2
GT3
0001-01
0002-01
0003-01 —
0004-01
0005-01
0001-02
0002-02 —
0003-02
0004-02
0001-03
0002-03 —
0003-03
0004-03
0001-05
0002-05 —
0003-05
0004-05
0001-06
0002-06 —
0003-06
0004-06
0001-07
0002-07 —
0003-07
0004-07
0001-18
0002-18 —
0003-18
0004-18
0001-20
0002-20
0003-20
• @No/ ** ⁄
NoCT@ LB *QT
X
BUSY
0001-23
0002-23 — Special character
0003-23
CASH
CHARGE
CHECK
SUBDEPT01
SUBDEPT02
SUBDEPT03
DEPT01
DEPT02
DEPT03
GROUP01
GROUP02
GROUP03
C01
C02
C03
TBL01
TBL02
TBL03
102
Fix total character
Transaction key character
Subdepartment character
Department character
Group character
Clerk character
Table character
0001-33
***ENDORSE MESSAGE******—
****************
0002-33
ESSAGE******
0001-34
***SLIP MESSAGE*********—
****************
0002-34
AGE*********
0001-39
CHARACTER RECALL********—
****************
0002-39
CALL********
ORDER01
0001-65
ORDER02
0002-65—
ORDER03
0003-65
0004-65
MC#01
0001-91
MC#02
0002-91—
MC#03
0003-91
Check endorsement message
Slip/external printer message
Recall character
Order character
Terminal connection table character
0001-96
AT COMMAND**************
************************— AT command
**************
0002-96
— Online password
ATA
ATI4
PASSWORD
0001-97
To print the PLU/flat-PLU program
OPERATION
REPORT
P01.................... — Program read symbol
PGM
—
#000001 - #999999
PLU0001
0001-04—
#000001—
1.2
@1.00—
PLU0002
0002-04
#000002
1
@2.00
Mode switch
8
6s
8
Read range
Item character/rec-#/file-#
Random code
Unit quantity/unit price
104s (PLU unit price read)
304s (PLU program read)
8
::::::
PLU start No.
8 If skipped, starts from PLU1.
F
8
::::::
PLU end No.
8 If skipped, ends the last PLU.
—
#000001 - #999999
PLU0001
0001-04—
00000000000000—
11-66
000000—
12-66
#000001—
13-66
<- 0001-28—
14-66
0—
15-66
@1234.56—
16-66
000000—
17-66
00—
PLU0002
0002-04
00000000000000
11-66
000000
Read range
Item character/rec-#/file-#
Batch program 01 ~ 1066, 18 ~ 1966
Batch program 1166
Batch program 1266
Batch program 1366
Not used
Batch program 1566
Not used
Not used
F
8
F
TK-6000/6500 User’s Manual
103
Advanced Operations
P03.................... — Program read symbol
Troubleshooting
This section describes what to do when you have problems with operation.
When an error occurs
Errors are indicated by an error codes. When this happens, you can usually find out what the problem is as
shown below.
Press C and check the appropriate section of this manual for the operation you want to perform.
Error code
Meaning
E001
Mode switch position changed before finalization.
Clerk button pressed before finalization of a registration being
performed under another clerk button.
E003
The signed on clerk differs from the clerk performed the tracking
check registration.
E004
Initialization or unit lock clear operation in progress.
E005
Memory allocation exceeds total memory capacity.
E008
Registration without entering a clerk number.
E009
Operation without entering the password.
The drawer is left open longer than the program time (drawer
E010
open alarm).
E011
Attempt to register while the cash drawer is open.
E013
Journal paper near end. (option)
E015
Printer error
E016
E017
E018
E019
E021
E023
E024
E026
E029
E030
E031
E032
E033
E035
E036
E037
E038
E040
E041
E044
E045
E046
E047
E048
E049
E050
E051
E053
E054
104
Action
Return the mode switch to its original setting and finalize the operation.
Press the original clerk button and finalize the transaction before
pressing another clerk button.
Input correct check number or assign the proper clerk number.
Complete operation.
Reallocate memory or expand memory (if possible).
Enter a clerk number.
Enter password.
Close the drawer.
Shut the cash drawer.
Replace the journal paper.
Switch to another mode and then back to the RF mode for the next
transaction.
Attempt made to register an item without inputting a check number. Input a check number.
Attempt made to register an item without inputting a table number. Input a table number.
Finalize operation attemped without entering the number of
Enter the number of customer.
customer.
No department linked PLU is registered.
Correct the program.
Actual stock quantity becomes less than the minimum stock
Perform stock maintenance.
quantity.
Actual stock quantity becomes/is negative.
Perform stock maintenance.
No condiment/preparation PLU is registered.
Register condiment/preparation PLU.
Item registration is prohibited, while partial tender.
Finalize the transaction.
Finalization of a transaction attempted without registering rate-tax.
Register <RATE TAX>.
Finalization of a transaction attempted without confirming the subtotal. Press <SUBTOTAL>.
Finalization of a transaction attmempted without confirming of the
Press <FS/ST>.
food stamp subtotal.
Finalize operation attempted without entering amount tender.
Enter the amount tendered.
Change amount exceeds preset limit.
Input amount tendered again.
Contents of the drawer exceed programmed limit.
Perform pick up operation.
High amount lock out/low digit lock out error
Enter correct amount.
Read/reset operation without declaring cash in drawer. This error
Perform money declaration.
appears only when this function is activated.
Attempt to register a new transaction without issuing a guest receipt. Issue a guest receipt.
Attempt to register a new transaction without validation.
Perform validation operation.
Attempt to register a new transaction without printing check.
Perform check print.
Attempt to register a new transaction without printing check
Perform check endorsement.
endorsement.
Registration buffer full.
Finalize the transaction.
Separate check buffer full.
Allocate sufficient separate check buffer.
Attempt to register a new transaction without printing slip.
Perform slip printing operation.
No paper is inserted or paper is out in the slip printer.
Insert new slip paper.
Check tracking index memory full.
Finalize and close the check number currently used.
Check tracking detail memory full.
Finalize and close the check number currently used.
Attempt to made use <NEW CHECK> to open a new check using
Finalize and close the check that is currently under the number that you
a number that is already used for an existing check in check
want to use or use a different check number.
tracking memory.
Use the correct check number (if you want to reopen a check that already exists
Attempt made to use <OLD CHECK> reopen a new check using a
number that is not used for an existing check in check tracking memory. in check tracking memory) or use <NEW CHECK> to open a new check.
Check number range over.
Enter correct number.
Two consecutive transactions attempted in the refund mode.
Troubleshooting
Action
Terminate separate check operation.
Press <EAT-IN> or <TAKEOUT>.
Replace new paper.
Print from the beginning of the transaction.
Register item(s) until the balance becomes positive amount.
Clear the data.
Perform it at master terminal.
Enter proper minus/coupon amount.
Set the arrangement properly.
Set memory cassette.
Check the operation and retry.
Use a vacant (formatted) memory cassette.
Check the write protect switch.
Ceheck the operation and retry.
In case of power failure
•
•
•
•
If the power supply to the cash register is cut by a power failure or any other reason, simply wait for power to be
restored. The details of any on-going transaction as well as all sales data in memory are protected by the
memory backup batteries.
Power failure during a registration
The subtotal for items registered up to the power failure is retained in memory. You will be able to continue with
the registration when power is restored.
Power failure during printing a read/reset report
The data already printed before the power failure is retained in memory. You will be able to issue a report when
power is restored.
Power failure during printing of a receipt and the journal
Printing will resume after power is restored. A line that was being printed when the power failure occurred is
printed in full.
Other
The power failure symbol is printed and any item that was being printed when the power failure occurred is
reprinted in full.
The memory protection battery is constantly charging and discharging as you switch the cash register on and off
during normal operations. This causes the capacity of the battery to decrease after approximately five years of
use.
Important !
• Remember …a weak battery has the potential of losing valuable transaction data.
• A label on the back of the cash register shows the normal service period of the battery installed in
your cash register.
• Have the battery replaced by your dealer within the period noted on this label.
TK-6000/6500 User's Manual
105
Troubleshooting
Error code
Meaning
E055
Normal registration is prohibited during separate check operation.
Attempt to finalize a transaction without specifying <EAT-IN> or
E059
<TAKEOUT>.
E060
External printer offline
E061
External printer went down.
E062
External printer paper end
E063
External printer is now printing.
E064
Printing buffer full
E066
Attept to print the last separated transaction on slip.
A
ttempt to finalize a transaction when balance is less than or
E075
equal to zero.
E085
Data exists in the consolidation file.
E100
Prohibit master operation.
E121
Network startup error.
Attempt to register <–> or <CPN> when the balance becomes
E139
negative.
E146
Arrangement file is full.
E200
No memory cassette is set.
Can not read, because no designated file is in the memory cassette
E202
or nternal flash memory.
Insufficient memory in the memory cassette or internal flash
E203
memory.
E204
Write protect switch of the memory cassette is on.
Can not write, because designated file has already been in the
E205
memory cassette or internal flash memory.
Troubleshooting
Clearing a machine lock up
If you make a mistake in operation, the cash register may lock up to avoid damage to programs and preset data.
Should it happens, you can use the following procedure to clear the lock up without losing any data.
1 Power off the register.
2 Insert the PGM key in the mode switch.
3 Press down f, and turn the mode switch to PGM mode.
4 The display shows ten Fs, then release f.
5 Press s. The display shows ten Fs and issue a receipt.
Important!
• If the register does not show ten Fs, never press s and call service representative.
When the register does not operate at all
Perform the following check whenever the cash register enter an error condition as soon as you switch it on. The
results of this check are required by service personnel, so be sure to perform this check before you contact a
CASIO representative for servicing.
Start
Is register plugged in?
No
Plug in the power cord.
Yes
Is power on?
No
Set the mode switch to any position other than OFF.
Yes
Do figures appear on the display?
Yes
No
Is the electrical outlet active?
No
Use other outlet.
No
Set to correct position.
No
Load paper.
Yes
Contact CASIO service
representative.
Do keys function?
Is the mode switch position
correct?
No
Yes
Yes
Contact CASIO service
representative.
Does paper feed?
No
Is paper loaded correctly?
Yes
Yes
Contact CASIO service
representative.
Printing becomes light?
Yes
Install new ink ribbon.
106
No
Contact CASIO service
representative.
To replace the ink ribbon
4
1
Load a new ink ribbon
cassette into the unit.
Open the printer cover.
5
2
Turn the knob on the right
side of the cassette to take
up any slack in the ribbon.
Remove the printer sub
cover.
3
Pull up the knob of the
ribbon cassette.
Knob
6
Replace the printer cover and printer sub cover.
Important!
Use only the ERC-32(P) ribbon (purple). Other types of ink ribbons can damage the printer.
Never try to extend the life of an ink ribbon by replenishing the ink.
Once an ink ribbon is in place, press <#/NS> or <NS> to test for correct operation.
TK-6000/6500 User's Manual
107
Troubleshooting/User Maintenance and Options
User Maintenance and Options
User Maintenance and Options
To replace journal paper
REG2 X1
REG1
Z1
1
OFF
Set the mode switch to the
REG1 position and remove
the printer cover.
X2/Z2
RF
PGM
2
6
Press j to feed about 20
cm of paper.
Cut the journal paper as
shown in the photograph.
3
7
Cut the journal paper at the
point where nothing is
printed.
Press j to feed the
remaining paper from the
printer.
4
8
Remove the journal take-up
reel from its holder.
Do not pull the paper out
of the printer by hand. It
can damage the printer.
5
9
Slide the printed journal
from the take-up reel.
Remove the old paper roll
from the cash register.
0
Load new paper as
described on page 10 of
this manual.
108
User Maintenance and Options
To replace receipt paper
1
under “To replace journal paper” on the previous page.
4
2
Do not pull the paper out of
the printer by hand. It can
damage the printer.
Cut the receipt paper as
shown in the photograph.
5
3
Remove the old paper roll
from the cash register.
Press f to feed the
remaining paper from the
printer.
6
Load new paper as
described on page 11 of this
manual.
To replenish the stamp ink
Follow step
1
under “To replace journal paper” on the previous page.
3
2
Squirt one or two drops of
ink into the holes on the
back of the stamp pad.
Remove the stamp pad
from its holder by lifting
the knob.
4
Replace the stamp pad on
its holder.
Options
Wetproof cover:
Memory chip:
Memory cassette:
C-NET card:
WT-78,
WT-79 (For TK-6000)
RAM-610-10LL
RAC-9
I/O-PB-14
Slip printer:
Cable:
External printer:
Cable:
Power supply:
SP-1300
PRT-CB-8C
UP-350, UP-250
PRT-CB-8A or PRT-CB-8B
PS-170 and AC-170
Consult with your CASIO dealer for details.
TK-6000/6500 User's Manual
109
User Maintenance and Options
Follow step
Specifications
Input method
Entry:
Department:
Display
10-key system, buffer memory 8 keys (2-key roll over)
Full key system
Amount 10 digits (zero suppression); department No., PLU No., No. of repeats, total, change,
receipt on/off, transaction indicator
Printer
Receipt:
Logo stamp:
Journal:
Validation:
Paper roll:
Paper feed:
Print speed:
Listing capacity
Amount:
Quantity:
Tendered amount:
Percent:
Tax rate:
Numbers:
Chronological data
Date print:
Time print:
Alarm
Dot matrix alpha-numeric system 24 digits, receipt on/off switch (key)
Store name or slogan is printed automatically
20 (H) × 30 (W) mm
Dot matrix alpha-numeric system 24 digits
Automatic take up roll winding
Journal paper near end sensor (option)
55 digits, one line, for 135 mm (minimum) wide slip
45 (W) × 83 (D) mm
Separate for receipt and journal
3.0 l/s
99999999
9999.999
9999999999
99.99
9999.9999
9999999999999999
Automatic date printout on receipt or journal, automatic calendar
Automatic time printout on receipt or journal, 24-hour system/12-hour system
Key catch tone, error alarm, sentinel alarm
Memory protection battery
48-hour full charge protects memories for approximately 90 days.
Battery should be replaced every five years.
Power supply/power consumption
See the rating plate.
Operation temperature
0˚C ~ 40˚C (32˚F ~ 104˚F)
Humiditiy
10 ~ 90%
Demensions and weight
454mm (H) × 345mm (W) × 218mm (D) /6.5kg
177/8" (H) × 139/16" (W) × 89/16" (D)/14lbs. 5oz.
…without drawer
Totalizers
Category
Department
PLU
Clerk
Hourly sales
Monthly sales
Transaction
No. of
totalizers
Amount
(10 digits)
Up to 10
Up to 108
10
24
31
Variable with
program
✔
✔
✔
✔
✔
Non ressettable
grand total
Reset counter
12
Consecutive No.
1
3
Contents
No. of items
Count
(6 integer/
(
4
digits)
3 decimal)
✔
✔
✔
✔
Periodic
totalizers
✔
✔
✔
✔
✔
Variable with
program
✔
(16 digits)
* Specifications and design are subject to change without notice.
110
No. of
customers
(6 digits)
✔
✔
(6 digits)
✔
Index
D
add check 24, 82
adding to a check 79
addition (+) 56
alphabet key 93
arrangement 24, 61
assigning a clerk 30
daily sales read/reset report 96
daily sales reset report 53
date display 31
date set 12
declaration 24
department 21, 23, 32
deposit 24, 85
descriptor 88
discount 20, 22, 40
display 18
double size letter key 93
drawer 17
B
backspace key 93
bill copy 24, 86
bottle link 60
bottle return 24, 60
bottom message 28, 88
E
C
cancel 21, 22, 24, 52
cash/amount tendered 21, 43
change 32
character code 92
character code fixed key 93
character enter key 93
character fixed key 93
character keyboard 93
charge 21, 23
check 21, 43
check endorsement 24
check print 24
check tracking 78
clearing a machine lock up 106
clerk button 17, 30
clerk interrupt 54
clerk key/button/lock 16, 30
clerk lock 17, 30
clerk name 30, 88
clerk number 20, 22, 87
clerk read/reset report 95
clerk secret number key 17, 30
clerk transfer 24, 84
closing a check 80
commercial message 28, 88
commission rate 87
consecutive No. 28
correction 50
coupon 24, 58
coupon II (2) 24, 58
credit 21, 23, 43
cube 24
currency exchange 24, 62
customer display 18
customer number 24
eat-in 24
EBT (electronic benefits transfer) 24, 73
entering character 92
error code 104
error correction 21, 22, 51
Euro 21, 44
F
financial read report 95
flat PLU 21, 22, 32
food stamp 64
food stamp shift 24, 64
food stamp subtotal 24, 64
food stamp tender 24, 64
Specifications/Index
A
G
group read/reset report 99
guest receipt 80
H
high amount limitation 34
hourly sales read/reset report 98
I
Illinois rule 67
indicator 19
individual clerk read/reset report 95
individual department, PLU/flat-PLU read report 94
ink ribbon 14, 107
item counter 28
J
journal 10, 28, 108
journal skip 28
K
Ketten Bon 24
keyboard (TK-6000) 20
keyboard (TK-6500) 22
TK-6000/6500 User's Manual
111
Index
L
P
left cursor key 93
loan 20, 22, 49
logo message 28, 88
paid out 21, 23, 48
paper feed 20, 22
periodic sales 100
pick up 20, 22, 49
PLU 36
PLU/flat-PLU read/reset report 98
plus 25
post receipt 20, 22
power failure 105
premium (%+) 25, 56
preset price 35
preset tax status 35
preset tender 59
previous balance 25
previous balance subtotal 25
price 25, 38
price inquiry 25
printing slip 77
program end key 93
M
machine No. 28
main display 18
manual tax 24
media change 49
menu shift 24
merchandise subtotal 24, 39
message 28, 88
minus 20, 22, 41
mixed tender 43
mode key 15
mode switch 16
money declaration 95, 97
monthly sales read/reset report 99
multiplication 21, 33, 37
multiplication/for 21, 23, 33
R
N
rate tax 25
read report 94
recall 25
receipt 11, 28, 109
receipt on/off 20, 22
receipt on/off switch / key 14
received on account 21, 23, 48
reduction (-) 41
refund 20, 22, 47
repeat 19, 32, 37
reset report 53, 94
return 47
review 25, 83
RF mode 47
right cursor key 93
roll paper 14
new balance 24, 79
new check 24, 79
new/old check 24, 81
no sale 20, 22, 24, 52
non add 20, 23, 24
normal receipt 25
number of customers 75
O
old check 25, 79
open 20
open check 25
open II (2) 25, 76
open PLU 38
opening a check 79
operator number 25, 84
operator X/Z 25
option 109
112
S
separate check 25, 83
set menu 61
shift key 93
sign off 30
sign on 30
single item 32, 37, 55
slip 77
slip back feed/release 25, 77
slip feed/release 25, 77
slip print 25, 77
space key 93
split sales of packaged item 33, 38
square 25
stamp ink 109
store 25
subtotal 21
Index
T
table number 25, 82
table transfer 25, 84
takeout 25
tax exempt 25
tax shift 20, 22, 39
taxable amount subtotal 25
text print 25
text recall 25, 76
time display 31
time set 12
tip 25, 74
trainee status 87
tray total 25, 57
V
validation 20, 22, 46
VAT 20, 85
void 25
W
Index
wetproof cover 15, 109
TK-6000/6500 User's Manual
113
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome
Shibuya-ku, Tokyo 151-8543, Japan
SA0002-A
TK-6000*E