Analog way Orchestra^2 User manual

Add to my manuals
4 Pages

advertisement

Analog way Orchestra^2 User manual | Manualzz

QUICK START GUIDE

Orchestra²

- Ref. ORC50

Thank you for choosing Analog Way and the Orchestra². By following these simple steps, you will be able to setup and use your powerful High End Remote Controller within minutes. Discover the Orchestra² extensive capabilities and intuitive interface while configuring your first show, and unleash your creativity for a new experience in show and event management by Analog Way.

WHAT’S IN THE BOX

• 1 x Orchestra² (ORC50)

• 1 x Power supply cord

• 1 x Console mounting bar and screws

• 1 x Set of 3 stylus for touchscreen

• 2 x Adjustable feet

• 1 x User manual (PDF version)*

• 1 x Quick start guide*

* User manual and quick start guide are also available on www.analogway.com

ORCHESTRA² SETTINGS

Before starting with Orchestra², please see the following steps:

• Front Panel Description

• Setting up the Orchestra²

• Configurating the show.

If connecting the Orchestra² and device directly, be sure to use an Ethernet crossover cable, otherwise you can use a standard ethernet hub and straight cables.

The Orchestra² automatically detects if the connected devices are running the correct firmware version.

To program a preset, use the following steps:

1.

Select a Screen #1 to #6

2.

Create a layer by “Preset Edition” section

3.

Select a source

4.

Save the configuration of the Screen in a Preset.

>> Restart the steps #1 to #4 if several Screens are associated to a Preset.

Specific commands:

• For saving a Preset with black content, you must save an empty Preset.

• Short press on a preset: loads the saved preset and saved screen selection.

• Long press on a preset: loads the saved preset on only the currently selected screens

• For clearing a Preset (Memory): Save To Preset >

Confirm the reset of the preset on the touch screen.

The check boxes are not automatically checked by the software.

The operator must confirm the action of erasing.

Status Bar (upper right corner of the screen).

Each Screen is represented as a circle:

• Ready Status Bar

- Grey dark circle: No device Configured

- Grey light circle: Device not connected

- Yellow circle: Initializing and synchronizing device

- Green circle: Device connected and ready for operation.

• TAKE Status Bar

- Grey dark circle: No device

- Grey light circle: Screen unselected, no action scheduled

- Red circle: The Main is different from Preview.

The screen will change after a Take.

Navigation bar (bottom of screen):

The Navigation bar shows your current page, and is also a shortcut to the listed menu pages.

FRONT PANEL DESCRIPTION

Please refer to User manual for comprehensive explanations.

Preset memory: Each time you configure a screen (background,

PIPs, logos), you can save it to a Preset Memory for future use.

To do this, configure a screen with all the desired elements, press the SAVE TO PRESET button and then a preset memory button.

Settings: allows you to access all of the Orchestra menus and functionalities quickly and easily. The 4 top rotative knobs will allow you to set values, while the last knob will allow to navigate through the interface, to access source or element settings for example.

Position: Joystick for easy adjustments (position/size). Adjust the selected PIP or Logo, X-Axis (Left/Right), Y-Axis (Up/Down).

Snap function: Enable this function by long pressing POS or

SIZE buttons. With this tool, your PIP/logo will be automatically positioned at the closest predefined position.

Screen: Screen selection

Source main:

Status only

Source Preview: select your sources. It will appear on the

Preview output of your switcher and press TAKE to go live on your

Main output.

Preset Edition: Save, load and modify presets.

Various layer properties are also available in this section.

- CLEAR ALL: delete all layers.

- QUICK FRAME: allows the instant display of a stored emergency frame above all layers. NOTE: This function requires Eikos², Saphyr, SmartMatriX², Pulse²,

QuickMatriX or QuickVu.

Please refer to our User manual for all the functions in this section.

Transition: Selection of Effects and User Effects.

T-Bar to control effect level.

TAKE: Press the TAKE button to display the pre-selected sources onto the MAIN output with the selected effects.

• 3 functions associated with TAKE and T-BAR:

- STEP BACK: > short press activates the Step Back function

> long press to enable/disable the PRESET TOGGLE function.

- INIT T-BAR

- TAKE CUT

SETTING UP THE ORCHESTRA²

USER CONFIGURATION:

On startup, the Orchestra² tactile screen will display the

User page. The first time you use the Orchestra², you will have to create a new user.

1.

Press the New User button on the tactile screen

2.

Name the new user as required and press the OK button to validate your choice. Press OK to skip password creation.

3.

On the User page, choose the user you just created, and press the OK button. The Orchestra² will display its default menu screen.

SYSTEM CONFIGURATION:

The Orchestra² System Configuration page lets you adjust properties like the IP address of the Orchestra².

1.

Press System on the tactile screen. The Network

Configuration tab will be displayed.

2.

Select the Lan Settings option, rotate the corresponding knobs to change the IP address of the Orchestra² (IP1,2,3,4) or press the <Default> button to restore the address to 192.168.0.9.

Press the OK button to validate

3. Press OK again to Exit the system page.

CONFIGURING THE SHOW

SHOW CONFIGURATION:

When starting with the Orchestra², you will need to create a new show.

1.

Press the Shows button on the tactile screen then “Create a New Show” button.

2.

The Orchestra² will display the Show Edit Name screen, you can now enter a new name. Choose a name for your show, then press the OK button to validate your choice.

3.

The Orchestra² will display a blank show page.

SCREEN SETUP:

1.

Select a Screen in the Screen section of the Orchestra² by pressing one of the six available buttons. The Screen page will appear on the Orchestra² tactile screen.

2.

Press Screen Setup on the tactile screen.

3.

On the <Screen Setup>, select the slave device type and mode. Press Edit to rename your screen.

4.

Press Edit Devices. Add Device. Using the tactile screen, Configure the communication settings of the device that the ORC50 will control.

5.

Press the OK button to validate your changes. The

Orchestra² will begin connecting to the configured device.

6.

Press the OK button to return to the Screen Setup page.

OUTPUT CONFIGURATION:

1.

In the Screen Setup page, press Edit Outputs and select the output, Main or Preview, you wish to adjust, then configure the output format

(resolution), output rate, output type required.

2.

Press Pattern, and select an available pattern to check your output settings on screen. Press

Pattern again, and select None to revert to your image on screen.

3.

Press the OK button to return to the screen setup page.

INPUT CONFIGURATION:

1.

In the Screen Setup page, press Edit Input, you can manually configure the type of plug, the signal type or press the AUTO SETTING ALL button, for an automatic setup of your inputs.

2.

Press OK button.

SOFT EDGE SETUP:

Please refer to the Soft Edge Setup Chapter of the

User manual.

IMAGE SETTINGS:

In the screen setup page, to access source image settings, press the IMAGE SETTINGS button .

REAR PANEL DESCRIPTION

LOGOS & FRAMES CONFIGURATION:

1.

In the screen setup page, press the LOGOS/FRAMES button.

2.

Select a source you wish to use as a logo or frame.

3.

Choose the memory slot to save the Logo/Frame into, edit size, position with the joystick, and the keying settings by rotating the approriate knobs.

4.

Press STORE to store your logo or frame.

RS-232: Serial port

(not in use)

RJ-45 connector: Connect the Orchestra² to 10/100

Ethernet LAN using this female RJ-45 connector: used to control switcher

Auxiliary display output:

Clone of the tactile screen

RJ-45 - Auxiliary:

Not in use

DC 100-250 VAC

2A 50-60Hz

Mounting Bar:

For installation

FRONT PANEL DESCRIPTION

• LAYERS:

Backgrounds, frames, PIPs, and logos are all considered layers.

To work with a layer, press the BACKGROUND LIVE , BACKGROUND FRAME , ADD PIP or ADD LOGO button.

In the Source Preview section, select the source you wish to assign to that layer. It will appear on the Preview output of your slave device. Press TAKE to go live on your Main output.

Selected objects can be moved or resized with the help of the joystick.

Any selected object can be cleared by pressing the CLEAR button twice (to clear multiple layers, press CLEAR PIPS ,

CLEAR LOGOS or CLEAR ALL , twice).

Source parameters of the selected layer can be accessed via the options on the last line of the tactile screen or via the

5 th knob.

• THE TAKE BUTTON:

The TAKE button will bring everything you have configured, from your Preview output to your Main output.

The Orchestra² T-Bar makes the same transition, but you can manually control the progress of the effect.

The TAKE CUT button allows you to override all transition effects with a cut effect.

Finally, the STEPBACK button will help you to revert your main output to its previous screen state. Press the STEPBACK button and press TAKE to do this.

• PRESET MEMORIES:

Each time you configure a screen (background, PIPs, logos), you can save it to a Preset Memory for future use, then call it back at any time.

To do this, configure a screen with all the desired elements, and press the SAVE TO MEMORY button.

In the Preset Memory section, choose the memory slot you wish to save to by pressing a button (#1 to #8).

To recall that memory and use it, press the LOAD FROM PRESET button, press a Preset Memory button and press TAKE .

TIP: Pressing the PAGE button while selecting a Preset Memory (#1 to #8), will select a memory page, each containing 8 memory slots (64 in total).

• OFF-LINE PROGRAMMING:

Define your Show while you have no hardware device connected to the ORC50. You can configure screens and define presets in advance and recall them later.

MANAGING WITH THE ORCHESTRA²

The Orchestra² can control the following Seamless Switchers:

Control Mode

Seamless Mixer

Seamless Matrix

Quadravision

Soft Edge Blending x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x

WARRANTY

All Analog Way products have a 3 year warranty on parts and labor, return to factory, but do not include faults resulting from user negligence, any unauthorized modifications, electrical surges, mishandling (drop/crush), and/or any other damage caused by misuse.

Please note: The included carrying case and protective foam is not covered under warranty.

GOING FURTHER WITH THE ORCHESTRA²

Please check the User manual and our website for further information: www.analogway.com

Version: 4.00 - 04/24/2014

Code: 140104

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement