Combi Savona TS 4200 Series Specifications

Door control
and security
hardware
Introduction
Since pioneering the first exit device in 1908, Von Duprin life safety products have
provided unparalleled quality, performance and flexibility for schools, hospitals,
stadiums and public buildings.
From innovative exit devices to electronic access control solutions and accessories,
Von Duprin never compromises when lives are at stake.
Von Duprin exit devices meet or exceed domestic and international quality
standards. All devices are UL listed for panic or fire hardware and are ANSI certified.
Many models are built to resist hurricane conditions.
VON DUPRIN
Administrative Offices
2720 Tobey Dr.
Indianapolis, IN 46219
Customer Service
877-671-7011
800-999-0328 - Fax
2 • Von Duprin Door control and security hardware
Technical Support
877-671-7011
Table of contents
Electric strikes
4200 Series electric strikes
4-5
5100 Series electric strikes
6-7
6000 Series electric strikes
8
6100 Series electric strikes
9-11
6200 Series electric strikes
12-16
6300 Series electric strikes
17-18
Electric strike / Lock information
19
E996L Electrified Breakaway
lever trim
20
Lever styles
21
EL/QEL Electric latch retraction
22
RX/LX Switches
23
SS Signal switch
24
RX330/RX350 Push pad
25
Chexit delayed exit
26-27
DE 5101
28
ALK Exit alarm kit
29
GUARD-X
30
E7500 Electric mortise lock
31
Electrical options / Power supplies 32
Electric power transfer
accessories
33
Monitor strikes
34-36
Mullions
37
Von Duprin Door control and security hardware • 3
4200 Series electric strikes for cylindrical locks
Overview
The 4200 Series electric strikes are easy to order, configure in the
field and install. This makes it a great choice for commercial
applications where traffic control is the primary function.
Compatible with a wide range of cylindrical devices, the 4200
series makes electrifying an opening simple. It is designed and
tested to work will all Schlage and Falcon cylindrical locks as
well those of many other manufacturers’.
4200 Series electric strikes for cylindrical locks
With a variety of field configurable options, the 4200 series is
able to address a broad range of needs. The power failure mode
(fail safe or fail secure) can be changed in the field without
disassembling the strike. The 4200 series also features a 12/24
dual-voltage solenoid for field wiring of either input voltage.
Additional factory orderable options provide even greater
flexibility. The 4200 series can be ordered with or without
latchbolt monitor. Square face plate is offered standard to
accommodate hollow metal frames, and rounded corner
faceplates are available as an option for aluminum frames.
An entry buzzer and rectifier kits are also available options.
The 4200 was developed with Von Duprin’s high standards and
engineering expertise. Its heavy duty stainless steel construction
is designed to withstand abuse.
Features
§§ Field configurable 12/24 voltage utilizing dual-voltage internal
solenoid
§§ Field configurable power failure mode (fail-safe/fail-secure)
Technical specifications
Strike
12 VDC
12 VDC
Current (amps)
0.20 A
0.10 A
Latchbolt monitor
30 VDC
Current (amps)
0.20 A
The 4200 series requires a DC regulated power supply, and the Schlage PS900 series
power supplies are recommended.
§§ Non-handed, internal solenoid design
§§ Heavy duty stainless steel faceplate
§§ Latchbolt monitoring standard on 4212 only
Model specifications
Model number
4211
/4 "
4212
/8 "
§§ Optional entry buzzer and rectifier kits available for AC to DC
operation
Latchbolt throw
Latchbolt monitor switch
---
•
§§ 1 year electrical product warranty
Face plate length
4 7/8 "
4 7/8 "
Backbox depth
1 3/8 "
1 3/8 "
Cylindrical
•
•
Deadlatch
•
•
Mortise
---
-----
Lockset
Lockset compatibility
The 4200 series is compatible with all Schlage and Falcon
cylindrical locks as well as cylindrical and deadlatch locks of
many other manufacturers.
§§ The 4211 is compatible with locksets with 5⁄8" (15 mm) throw
latchbolts, or up to 3⁄4" (19mm) throw latchbolts with a 1⁄8"
door gap.
§§ The 4212 is compatible with locksets with ⁄2" (12.7mm) throw
latchbolts, or up to 5⁄8" (15 mm) throw latchbolts with a 1⁄8"
door gap.
44• Von Duprin Door control and security hardware
3
5
Rim exit devices
---
Number
of doors
Single
•
•
Pair
---
---
Door and
frame type
Hollow metal
•
•
Aluminum
•
•
Wood
---
---
EB (entry buzzer fail-secure only)
•
•
SO12 & SO24 rectifier
kit for AC to DC
operation
•
•
Round corner faceplate
•
•
1
Options
4200 Series electric strikes dimensions
Ordering information
Brown
Brown-White
24 VDC strike wiring
1
2
3
* Optional
Selections correspond with the numbers above
Orange
24 VDC input
nonpolarized
Buzzer*
Orange-White
Rectifier
kit*
12 VDC input
nonpolarized
Model
4200 -S024- EB
Orange
Orange-White
Brown
Brown-White
Latchbolt monitoring switch (4212 only)
1
Model
4211
4212
See model specification chart to make the proper selection
See model specification chart to make the proper selection
2
Rectifier kit (optional)
S012
S024
Converts 12 VAC voltage to 12 VDC to operate the solenoid
Converts 24 VAC voltage to 24 VDC to operate the solenoid
3
Buzzer (optional)
EB
Entry Buzzer, with fail-secure (FSE) configured
4200 Series electric strikes dimensions
12 VDC strike wiring
Standard features
S1
S1
Red
Red
Blue
Blue
Yellow
Yellow
§§ Power failure mode: Field configurable fail-secure/ fail-safe
§§ Voltage: Field configurable 12 VDC/24 VDC dual voltage solenoid
§§ Finish: 630 satin stainless steel
Switch shown with latch status tripper depressed
5
Von Duprin Door control and security hardware • 5
5100 Series electric strikes for cylindrical locksets
Overview
The Von Duprin 5100 electric strike has been designed and
manufactured to meet the needs of locksmiths and security
professionals. This easy-to-install electric strike was created for
medium-duty applications, specifically to control traffic flow
through interior and exterior openings in retail and commercial
environments.
5100 Series electric strikes for cylindrical locksets
The 5100 electric strike is designed for maximum flexibility. It
comes standard with three faceplates for hollow metal, wood or
aluminum frames in every box. The internal 12/24VDC solenoid
provides additional versatility. While the adjustable keeper
improves fit for applications with weather stripping or tight door
preps. Furthermore, power failure mode is field selectable
fail-safe/fail-secure.
With multiple faceplates and flexible options, the 5100 provides
added convenience by ensuring the right parts are in the box to
get the job done. This reduces labor expense and reduces return
trips to the job site.
The 5100 was developed with Von Duprin’s high standards and
engineering expertise. Its heavy-duty construction and tamperresistant design is able to withstand abuse. The 5100 is tested to
over one million cycles and provides 1300 lbs holding strength.
Technical specifications
Power options
Features
§§ Three faceplates standard in every box
§§ 12/24 dual-voltage
§§ Fail-safe/fail-secure
DC: Regulated power supplies
(recommended)
PS902 power supply
AD/DC: Conversion
Von Duprin SO-24 kit
12VDC
12VDC
Resistance (ohms)
32
128
Power (watts)
4.5
4.5
§§ Backbox depth of 1 ⁄16" Current (amps)
0.38
0.19
§§ Keeper depth of ⁄2"
All specs ± 10% @ 77°F/25°C
§§ Adjustable keeper
§§ Internal solenoid §§ Non-handed
11
1
§§ Mounting tabs
§§ Retrofit kit
§§ Illustrated installation instructions
Model specifications
Model #
5100
§§ One year electrical product warranty
Latchbolt throw
1
§§ Continuous duty operation
Face plate length
4 7⁄8" or 7 15⁄16"
§§ Heavy duty construction
Depth
1 11⁄16"
§§ Meets BHMA A156.31, Grade 1 for endurance and dynamic
strength, and Grade 2 for static strength
Lockset
Cylindrical
Door/frame type
Hollow metal, aluminum and wood
Number of doors
Single
Certifications
ANSI/BHMA 156.5 Grade 1,
UL 1034 burglary listing
Application notes
Versatile electric strike for aftermarket,
covering multiple applications in one SKU.
§§ Tamper resistant
§§ Static strength 1300 lbs
§§ Dynamic strength 70 ft-lbs
§§ Endurance 1,000,000 cycles
⁄2" to 5⁄8" with 1⁄8" door-frame gap
Lockset compatibility: Keeper depth of 1⁄2" is sufficient to accommodate all cylindrical
locks up to 5⁄8" throw and most aluminum narrow stile deadlatches.
66• Von Duprin Door control and security hardware
5100 Series electric strikes dimensions
5/32" radius
on 4 corners
5/32" radius
on 4 rners
co
(Aluminum frame)
3-23/32"
3-31/32"
2-7/16"
7-7/16"
7-15/16"
2-1/16"
4-7/8"
4-1/8"
1-1/16"
1-1/2"
1"
1-11/16"
1-11/16"
CL strike
3-3/8"
31/32"
1-1/4"
31/32"
5/8"
CL Lock and strike
23/32"
CL Lock and strike
5100-S 024
12 VAC input
12 VDC output
Yellow for 12V
Red for 24 V
White
1
White
Rectifier kit*
Ordering information
Model
Solenoid power requirements; 12VDC, 0.38 A, 24 VDC, 0.19 A
For DC operation, Von Duprin PS902 series power supply is recommended. For AC
operation, Von Duprin SO24 kit is recommended.
2
* Optional
Black
Selections correspond with the numbers above
SO Kit
24 VAC input
24 VDC output
1
Model
5100
Electric strike for cylindrical locksets
2
Rectifier kit (optional)
S012Converts 12 VAC voltage to 12 VDC to operate the solenoid
S024Converts 24 VAC voltage to 24 VDC to operate the solenoid
12 VDC strike wiring
Red
12 VDC input
nonpolarized
Black
Red-White
Black-White
Standard features
5100 Series electric strikes dimensions
1-7/16"
3/32"
§§ 24 volts DC
24 VDC strike wiring
§§ Fail-secure
Red
24 VDC input
nonpolarized
§§ Field convertible to fail-safe
Black
Red-White
Black-White
7
Von Duprin Door control and security hardware • 7
6000 Series electric strikes
Overview
Von Suprin 6000 Series electric strikes
Von Duprin is the leading manufacturer of premium, heavy-duty
electric strikes known for their reliability, durability and security.
Electric Strikes provide remote release of a locked door. They
allow the door to be opened without retracting the latchbolt.
This occurs by the releasing of the electric strike lip (sometimes
called keeper or gate). When the door closes the beveled
latchbolt rides over the lip and falls into the electric strike pocket.
Von Duprin 6100 Series electric strikes
Electric strikes for use with rim exit devices
Von Duprin 6200 Series electric strikes
Electric strikes for use with mortise/cylindrical electric locks
Versatility
§§ Furnished 24VDC standard with 12VDC and AC operation
optional. 16VDC solenoids available.
6000
6000 Series electric strikes
§§ Furnished fail secure (FSE) standard, with fail safe (FS)
optional.
§§ Strike box is adjustable to compensate for misalignment of the
door or frame.
§§ Two piece plug connectors are furnished for ease of installation
and for removal during strike servicing.
Durability
Developed with Von Duprin’s high standards and engineering
expertise.
§§ Heavy-duty stainless steel construction. Tested to over
250,000 cycles.
Options
AC operation
SO12 and SO24 are rectifier kits to convert AC voltage to operate
the DC solenoids. These kits are field installable and plug in-line
to solenoid.
DS and DS-LC — Dual switch monitoring
(Factory Installed Only)
Dual switch monitoring option has two SPDT contacts, one
switch monitors the tripper which is depressed when the
latchbolt is inserted into the strike pocket. The second switch
monitors the condition of the strike lip, open or closed and
locked.
Features and Benefits
§§ Stainless Steel Construction
§§ Accepts 3⁄4" (19mm) Throw Latchbolt
§§ Six Finishes
§§ Non-handed
§§ Fail Secure
DS is standard, rated 24V, operating range from 2 ampere to 50
milliampere.
§§ Plug Connectors
Specifications
12V
Resistance in Ohms±10% @ 70°F
21
82
Watt-seated @ 70°F
7.5
8
Amps-seated @ 70°F
.6
.33
Amps-inrush @ 70°F
.6
.33
To order, specify
1. Model number
2. FS (fail safe, when required)
3. DS or DS-LC (dual switch, when required)
4. V
oltage 12VDC or 24VDC
For 16V solenoids order separately
5. SO12 or SO24 (required when using AC)
6. Finish: US3, US4, US10, US10B, US32, US32D
7. EB (Entry buzzer), FSE only (when required)
Note: Information listed is for use on new applications.
On retrofit applications, modification of the frame preparation
may be required, consult factory.
24V
DS-LC low current gold contact switches for use on applications
associated with computer control and monitoring, rated 24V,
operating range 50 milliampere or below.
Fail secure — FSE
FSE — FAIL-SECURE electric strikes require power to be applied
to unlock the strike lip. On loss of power, the strike is locked. Field
convertible with parts.
Fail safe — FS
FS — FAIL-SAFE electric strikes require power to be applied to
lock the strike lip. On loss of power, the strike is unlocked.
Building codes prohibit the use of fail-safe strikes on labeled
openings. Field convertible with parts.
Entry buzzer — EB
EB — Entry buzzer is available for use with fail-secure strikes.
Installed in the frame and in parallel with the circuit, the buzzer
will sound when the strike is unlocked.
UL listed
UL Listed Burglary-Resistant and Electric Strike for fire doors and
frames. A label for single doors and B label for double doors.
Strikes meet the requirements of ANSI 156.5, Grade 1, 1992.
+ Dual Monitor Switches (DS or DS-LC) are not available on open back strikes.
88• Von Duprin Door control and security hardware
6100 Series strikes for rim exit devices
Overview
Von Duprin electric strikes are known for their reliability,
durability and security. The 6100 Series is designed to withstand
abuse. Its heavy-duty stainless steel construction is fully UL1034
and UL10C Listed and ANSI/BHMA Grade 1, 1500 lb hold force
rated.
6100 Series electric strikes are designed for use with a variety of
rim exit devices. They interface with the latch mechanism of the
exit device. The movable lip (keeper) allows a door to open even
when the latch bolt is extended. This feature, called remote
release, provides added benefits such as increased convenience
and efficiency. The 6100 Series also provides added security and
traffic control.
6100 Series electric strikes can be used for retrofit applications
or new construction. To assure the proper selection of an electric
strike on new applications, lockset compatibility charts are
shown on the next page. When using a lockset not listed or when
door, power must be applied. Fail-safe strikes which are
commonly used for life safety applications are non-fire-rated. To
unlock a fail-safe strike, power is removed. The 6100 comes
standard 24 VDC; 12 VDC and AC operation are optional.
Features and benefits
§§ Non-handed design provides greater flexibility
§§ Strike box is adjustable to compensate for misalignment of the
door or frame
§§ Two piece plug connectors are furnished for ease of installation
and for removal during strike servicing
§§ ANSI 156.5 Grade 1, 1500 lb hold force rated
§§ UL1034 burglary-resistant and UL10C electric strike for fire
door
§§ Six finishes available to suite with existing hardware
§§ Durable stainless steel construction
§§ 24 VDC standard with 12 VDC and AC operation optional
§§ Meets BHMA A156.31, Grade 1 for endurance and strength
The power failure mode of the 6100 can be specified at the time
of order. Fail-secure is available for fire rated openings. In a
fail-secure application, the door is normally locked. To unlock the
§§ Dynamic strength 70 ft-labs
§§ Static strength 1300 lbs
§§ Endurance 1,000,000 cycles
Model specifications
Model number
6111
6112
6113
6114
6121
Retrofits model
VD 3031
FA 310-4
VD 3011, VD 3021
FA 310-5
FA 310-4-100
Latchbolt throw
3
3
3
3
3
Face plate length
6"
9"
6"
7"
9 1⁄8"
Backbox depth
1 3⁄4"
1 3⁄4"
1 15⁄16"
---
N/A
Lockset
Rim exit device
Rim exit device
Rim exit device
Rim nightlatch
Rim exit device
Single




---
Double door with mullion

---
---
---
---
Double door without mullion
---
---
---
---






Aluminum





Wood



---

Blade stop shim
Yes
No
Yes
No
No
DS or DS-LC (dual monitor switches)
Yes
Yes
Yes
Yes
Yes
EB (entry buzzer - fail-secure only)
Yes
Yes
Yes
Yes
Yes
Number
of doors
⁄4"
Door/frame type Hollow metal
Options
⁄4"
⁄4"
⁄4"
Certifications
UL1034, UL10C, ANSI/BHMA 156.5 Grade 1, 1500 lb hold-force rated
Application notes
1
2
3
4
⁄4"
6100 Series strikes for rim exit devices
retrofitting a strike to an existing application, please contact Von
Duprin technical support for application assistance.
5
Note: 16 VDC and 28 VDC solenoid are sold as replacement parts for existing strikes. Please contact customer care for details.
Application notes:
1. For use with rim exit devices on single doors or double doors with mullion
applications. 1⁄2" projection blade stop shim 010055-XX available for use on
cased opening or blade stop frames. Specify when using 55 rim devices. May
also be used with vertical rod exit devices noted on previous page x Pullman
latch LBR. Non-fired-rated.
2. F
or use with rim exit devices on single door applications. Designed to replace
Folger Adam 310-4, minor fame prep modification required.
3. 1⁄2" projection blade stop shim 010055-XX available for use on cased opening
or blade stop frames. Non-fire rated.
4. S
urface applied strike for use with rim nightlatches on single door
applications. Designed to replace Folger Adam 310-5, with different mounting
hole locations from Folger Adam.
5. Non-fire rated. For use with rim exit devices on double door applications
without mullion. Strike mounts on inactive leaf. Replace Folger Adam
310-4-100.
Rim exit device compatibility
6111, 6112, 6113 & 6121 Strikes
Manufacturer
Device
Von Duprin
22, 33A, 35A, 551, 88, 98, 99
8827 LBR4 x Pullman latch Non-Fire rated
9827 LBR4 x Pullman latch Non-Fire rated
9927 LBR4 x Pullman latch Non-Fire rated
Falcon Monarch2
XX-R, 18-R, 19-R, 24-R, 25-R
Falcon Doromatic
1790
Precision2
2100
Sargent
2800, 6500, 6800, 8500, 8800, 9500, 98003, 9898
Yale
1500, 700
1. Strike must be factory modified, specify when using with a 55 Rim device
2. Deadlocking feature will not properly function, consult factory
3. Panic only, Not fire-rated
4. 6111 is recommended for LBR applications
Note: When using a lockset not listed or when retrofitting an existing application, please contact
Von Duprin technical support for application assistance
9
Von Duprin Door control and security hardware • 9
6100 Series strikes dimensions
Wiring
AC
6100 Series specifications
12V
24V
Resistance in Ohms±10% @ 70°F
21
82
Watt-seated @ 70°F
7.5
8
Amps-seated @ 70°F
0.6
0.33
Amps-inrush @ 70°F
0.6
0.33
Dimensions
AC with buzzer
6111
1 5/8"
(41mm)
6"
(152mm)
6112
1/2"
(13mm)
2 3/16"
(56mm)
4 1/2"
(114mm)
6100 Series strikes dimensions
9"
(229mm)
1 11/16"
(43mm)
4 1/2"
(114mm)
2 9/16"
(65mm)
7/16”
Minimum
Clearance
1 3/8"
(35mm)
7/8"
(22mm)
3/4"
(19mm)
1 5/8"
(41mm)
1 5/8"
(41mm)
1”
1 5/8"
(41mm)
13/16"
(21mm)
6-5/8”
7/8"
(22mm)
6”
DC
Minimum
Clearance
9/16"
(14mm)
RH door shown
3”
3-5/16”
CLstrike
#25 drill and #10-24 tap
4 places
Edge of frame
6113
1 5/8"
(41mm)
6114
15/16”
Edge of frame
1/2” diameter hole
for wiring access
2 places
Frame Preparation for Strike
7/8"
(22mm)
1”
1 15/16"
(49mm)
9/16"
(14mm)
7/16”
1-9/16”
1-15/16”
1”
6"
(152mm)
DC with buzzer
1-5/8”
3-3/32”
4 1/2"
(114mm)
2 1/4"
(57mm)
1 3/8"
(35mm)
7/8"
(22mm)
Minimum
Clearance
Strike Dimensions
2 1/2"
(64mm)
7/8"
(22mm)
1 5/8"
(41mm)
10• Von Duprin Door control and security hardware
10
9 1/8"
(232mm)
3-3/4”
1-7/8”
931243_00 Rev. 5/12-b
Optional DS (FSE shown)
7-1/2”
3-5/16”
6121
CL of latch
CL of strike
6-5/8”
6100 Series how to order
Ordering information
Voltage
3
4
5
Buzzer*
Dual switch*
2
Finish
Power
failure mode
1
Rectifier kit*
Model
6112-FSE -DS- 24 - S024 - US3 - EB
6
7
* Optional
Selections correspond with the numbers above
3
DS
DS-LC
4
24
12 Dual switch (optional)
Monitors latch bolt and lock status.
DS switches rated at 24 VDC
50 milliampere - 2 amps.
Optional for computer monitoring.
Monitors latch bolt & lock status.
DS switches rated 24 VDC
50 milliampere or less.
Voltage (VDC)
Low voltage DC power
Low voltage DC power
If AC power is required specify rectifier kit below.
5
SO12
S024
Rectifier kit (optional)
Converts 12 VAC voltage to 12 VDC
to operate the solenoid
Converts 24 VAC voltage to 24 VDC
to operate the solenoid
6Finish
US number/Von Duprin number
US3/85 Plated polished brass on
stainless steel
US4/84 Plated dull brass on stainless steel
US10/06 Plated dull bronze on stainless
steel
US10B/86 Plated dark bronze on
stainless steel
US32/31 Stainless steel, polished
US32D/32 Stainless steel, satin
7
Buzzer (optional)
EB
Entry Buzzer.
Only available if Fail-Secure (FSE) is specified.
6100 Series how to order
1Model
6111
See chart on page 3 to make the
proper selection
6112
See chart on page 3 to make the
proper selection
6113
See chart on page 3 to make the
proper selection
6114
See chart on page 3 to make the
proper selection
6121
See chart on page 3 to make the
proper selection
2
Power failure mode
FSE
Fail-secure. Requires power to be
applied to unlock the strike lip. On
loss of power, the strike lip is
locked.
Fire-rated.
FS
Fail-safe. Requires power to be applied to lock the strike lip. On loss
of power, the strike lip is unlocked. Non-fire-rated.
11
Von Duprin Door control and security hardware • 11
6200 Series strikes for mortise or cylindrical devices
Overview
Von Duprin electric strikes are known for their reliability,
durability and security. The 6200 Series is designed to withstand
abuse. Its heavy-duty stainless steel construction is fully UL1034
and UL10C Listed and ANSI/BHMA Grade 1, 1500 lb hold force
rated.
6200 Series strikes for mortise or cylindrical devices
6200 Series electric strikes are designed for use with a variety of
mortise or cylindrical locksets, as well as mortise exit devices. It
interfaces with the latch mechanism of the exit device. The 6200
Series movable lip (keeper) allows a door to open, even when
the latch bolt is extended. This feature, called remote release
provides added benefits such as increased convenience and
efficiency. The 6200 Series also provides added security and
traffic control.
6200 Series electric strikes can be used for retrofit applications
or new construction. To assure the proper selection of an electric
strike on new applications, lockset compatibility charts are
shown on the next page. When using a lockset not listed or when
retrofitting a strike to an existing application, please contact Von
Duprin Technical Support for application assistance.
The power failure mode of the 6200 Series can be specified at
the time of order. Fail-secure is available for fire rated openings.
In a fail-secure application, the door is normally locked. To unlock
the door power must be applied. Fail-safe strikes, which are
commonly used for life safety applications, are non-fire rated. To
unlock a fail-safe strike, power is removed. The 6200 Series
comes standard with 24 VDC; 12 VDC and AC operation are
optional.
Mortise Lockset Compatibility
6211, 6211AL, 6211WF, 6212, 6213, 6214, 6215, 6221, 6222,
6223, 6224, 6224AL, 6225 & 6226 Strikes
Manufacturer
Model Number
Von Duprin
7500
Adams Rite
4510, 4710
Baldwin
6000
Best
24H, 30H
Corbin
9000
Falcon
M2300, M2500, M2600, M3300, M3500, M3600
§§ Non handed design provides greater flexibility
Precision
Mortise
§§ Strike box is adjustable to compensate for misalignment of the
door or frame
Russwin
Mortise
Sargent
7700, 8100, 9000
Schlage
L9000, K30, K40, K50, K60
§§ Two piece plug connectors are furnished for ease of installation
and for removal during strike servicing
Yale
7030, 7130, 8600, 8700
§§ ANSI 156.5 Grade 1, 1500 lb hold-force rated
Mortise Lockset Compatibility
Features and benefits
§§ UL1034 Burglary-Resistant and UL10C Electric Strike for
Fire Door
6210
Manufacturer
Model Number
Von Duprin
7500
Best
30H (not 45H/47H)
§§ Durable stainless steel construction
Corbin/Russwin
§§ 24 VDC standard with 12 VDC and AC operation optional
ML2200, 5000, 9000, CR2200
(not 2000)
Falcon
M100, M200, M300, M400, M500, M600
§§ Meets BHMA A156.31, Grade 1 for endurance and strength
Sargent
7700, 8100 (not 7800/8200)
Schlage
L9000
Yale
8700 (not 8800)
§§ Six finishes available to suite with existing hardware
§§ Static strength 1300 lbs
§§ Dynamic strength 70 ft-lbs
§§ Endurance 1,000,000 cycles
Cylindrical Lockset Compatibility1,3
Specifications
12V
24V
Resistance in Ohms±10% @ 70°F
21
82
Watt-seated @ 70°F
7.5
8
Amps-seated @ 70°F
0.6
0.33
Amps-inrush @ 70°F
0.6
0.33
6211, 6211AL, 6211WF, 6212, 6213, 6214, 6215, 6221, 6222, 6223,
6224, 6224AL, 6225 & 6226 Strikes
Manufacturer
Model Number
Baldwin
1
Best
3
Corbin
1
Falcon
1
Russwin
1
Sargent
1
Schlage
3
Yale
1
⁄2" – 3⁄4" (13mm – 19mm)
⁄8" – 3⁄4" (10mm – 19mm)
⁄2" – 3⁄4" (13mm – 19mm)
⁄2" – 3⁄4" (13mm – 19mm)
⁄2" – 3⁄4" (13mm – 19mm)
⁄2" – 3⁄4" (13mm – 19mm)
⁄8" – 3⁄4" (10mm – 19mm)
⁄2" – 3⁄4" (13mm – 19mm)
1. Von Duprin cannot guarantee compatibility as other manufacturer’s designs may
change without notice.
2. Signalling may not function when using 3⁄8" (10mm) throw bolt. Deadlocking
cannot be guaranteed with all locks.
3. When using a lockset not listed or when retrofitting a strike to an existing application,
please contact Von Duprin Technical Support for assistance.
12• Von Duprin Door control and security hardware
12
6200 Series strikes for mortise or cylindrical devices
Wiring
AC
AC with buzzer
DC
DC with buzzer
Model Specifications
Model #
6210
6211
6211AL
6211WF
6212
Retrofits model
n/a
VD 3140, FA 712
FA 722
FA 732
VD 3146
Latchbolt throw
3
3
3
Face plate length
4 7/8"
4 7/8"
4 7/8"
/4"
Backbox depth
Lockset
# Doors
Door &
frame type
Options
/4"
/4"
3
3
4 7/8"
6 3/8"
1 21/32"
1 21/32"
4 1/2"
1 21/32"
Wood
•
--•
--•
•
---
•
•
•
--•
•
---
•
•
•
----•
---
•
•
•
------•
•
•
•
--•
•
---
DS or DS-LC (dual
monitor switches)
•
•
•
•
•
EB (Entry buzzer - fail secure only)
UL10C
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ANSI/BHMA 156.5 Grade 1
1500lb. Hold force rated
•
•
•
•
•
1
2
3
4
5
Cylindrical
Single
Pair
Hollow metal
Aluminum
16 VDC solenoid
UL1034
Application notes
/4"
1 21/32"
Mortise
28 VDC AC rectifier kit
Certifications
/4"
Application notes:
1For use with mortise locks without deadbolt on single door, hollow metal frame
applications and using ANSI prep at standard height. Strike pocket inserts are provided to
accommodate different manufacturers deadlocking trigger locations.
2For use on new installations with mortise locks without deadbolt or cylindrical locks on
single door, hollow metal frame applications. Designed to replace Von Duprin 3140 or
Folger Adam 712.
3For use on new installations with mortise locks without deadbolt or cylindrical locks on
single door, aluminum frame applications
6200 Series strikes for mortise or cylindrical devices
Optional DS (FSE shown)
4For use on new installations with mortise locks without deadbolt or cylindrical
locks on single door wood frame applications. Designed to replace Folger Adams
732. Wood frame horizontal solenoid location differs from Folger Adams. Requires
additional frame prep when retrofitting.
5For use with mortise locks without deadbolt or cylindrical locks on single door,
hollow metal or aluminum frame applications. Fits modified ANSI 115.2 cutout.
Designed to replace Von Duprin 3146
13
Von Duprin Door control and security hardware • 13
6200 Series strikes for mortise or cylindrical devices
Model Specifications
Model #
6212WF
6213
6214
6215
6216
6221
Retrofits model
n/a
VD 3041, 3042,
3061, 3062
FA 310-2 3/4
FA 310-2
FA 310-3-1
VD 3071 & 3072
Latchbolt throw
3
3
Face plate length
6 3/8"
• 6"
9"
4 3/4"
2 1/2"
1 5/8"
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Backbox depth
6200 Series strikes for mortise or cylindrical devices
Lockset
# Doors
Door &
frame type
Mortise
Cylindrical
Single
/4"
/4"
3
/4"
/4"
Hollow metal
Aluminum
Wood
EB (Entry buzzer - fail secure only)
28 VDC AC rectifier kit
16 VDC solenoid
UL1034
Certifications UL10C
ANSI/BHMA 156.5 Grade 1
1500lb. Hold force rated
•
•
•
•
•
•
•
See note 2 below
•
•
•
•
•
•
•
•
•
•
•
•
/4"
3
3
9"
6"
1 5/8"
3 5/32"
43/4"
•
•
•
•
•
•
•
•
9"
Pair
DS or DS-LC (dual monitor switches)
Options
/4"
3
•
•
•
•
•
•
Application notes
6
7
8
9
10
11
Model #
6222
6223
6224
6224AL
6225
6226
Retrofits model
FA 310-23/4 OB
VD 3091 & 3092
FA 310-2 3/4
FA 310-2RF
FA 310-2 OB
FA 310-2
Latchbolt throw
3
3
Face plate length
9"
6"
9"
Backbox depth
1 5/8"
4 1/2"
1 5/8"
1 5/8"
1 5/8"
1 5/8"
Cylindrical
•
•
•
•
•
•
•
•
•
•
•
•
Single
---
---
---
---
---
---
Pair
Aluminum
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Wood
---
•
•
•
•
---
---
---
---
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
12
13
14
15
16
17
Lockset
# Doors
Door &
frame type
Mortise
Hollow metal
DS or DS-LC (dual
monitor switches)
Options
EB (Entry buzzer - fail secure only)
28 VDC AC rectifier kit
16 VDC solenoid
UL1034
Certifications UL10C
ANSI/BHMA 156.5 Grade 1 1500lb. Hold
force rated
Application notes
/4"
/4"
3
/4"
3
/4"
9"
/4"
/4"
3
3
9"
9"
6For use with mortise locks without deadbolt or cylindrical locks on single door,
wood frame applications.
12Open back electric strike for use with mortise locks without deadbolt or cylindrical
locks on 1 3/4" (44mm) thick double door applications
7For use with mortise locks without deadbolt or cylindrical locks on
single door hollow metal or aluminum frame applications (includes wood frame on retrofit
applications). Designed to replace Von Duprin 3041, 3042, 3061 and 3062.
13Closed back electric stirke for use with mortise locks without deadbolt or
cylindrical locks on 1 3/4" (44mm) thick double door applications. 4 3/4" (120mm)
minimum stile required. For a concealed vertical rod and mortise device
combination specify “A” backbox.
8For use with mortise locks without deadbolt or cylindrical locks on sing door hollow metal or
aluminum frame applications. Designed to replace Folger Adams 310-2 3/4
9For use with mortise locks without deadbolt or cylindrical locks on single door hollow metal
or aluminum frame applications. Designed to replace Folger Adams 310-2.
10For use with mortise locks with deadbolt 1" throw on single door
hollow metal aluminum or wood frame applications. Deadbolt must be manually
operated. Designed to replace Folger Adams 310-3-1.
11Open back electric strike for use with mortise locks without deadbolt or cylindrical locks on
1 3/4" (44mm) thick double door applications. 4 3/4" (120 mm) minimum stile required. For a
concealed vertical rod and mortise device combination, specify “A” backbox.
14• Von Duprin Door control and security hardware
14
14Closed back electric strike for use with mortise locks without deadbolt or
cylindrical locks on 1 3/4" (44mm) or 2 1/4" (57mm) thick double door applications.
15Closed back electric strike for use with mortise locks without deadbolt or
cylindrical locks on 1 3/4" (44mm) or 2 1/4" (57mm) thick aluminum double door
applications.
16Open back electric stirke for use with mortise locks without deadbolt or cylindrical
locks on 1 3/4" (44mm) thick double door applications.
17Closed back electric strike for use with mortise locks without deadbolt or
cylindrical locks on 1 3/4" (44mm) or 2 1/4" (57mm) thick double door applications.
6200 Series strikes dimensions
Dimensions
6212
6210
1 1/4"
(32mm)
7/8"
(22mm)
1/2"
(13mm)
6215
1 15/32"
(37mm)
1 3/8"
(35mm)
1 11/16"
(43mm)
1 3/4"
(44mm)
4 7/8"
(124mm)
1 3/8"
(35mm)
1 1/4"
(32mm)
1 9/16"
(38mm)
(41mm)
3 3/8"
(86mm)
3 1/4"
(83mm)
12"
(305mm)
1/8"
(3mm)
3 3/8"
(86mm)
6 3/8"
(162mm)
12" (305mm)
Minimum
Clearance
2 1/16"
(52mm)
6212WF
1 1/4"
(32mm)
1/2"
(13mm)
12"
(305mm)
Minimum
Clearance
1/8"
(3mm)
3 9/16"
(90mm)
2 1/16"
(52mm)
7/8"
(22mm)
1/2"
(13mm)
6211AL
1 1/4"
(32mm)
1 11/16"
(43mm)
3 3/8"
(86mm)
2 1/6"
(52mm)
4 7/8"
(124mm)
7/8"
(22mm)
1 1/4"
(32mm)
2 3/16"
(56mm)
1 15/32"
(37mm)
1/2"
(13mm)
12"
(305mm)
Minimum
Clearance
3 7/8"
(98mm)
6"
(152mm)
1/8"
(3mm)
21/29"
(64mm)
4 1/2"
(114mm)
1/4"
(6mm)
4 1/2"
(114mm)
4 7/8"
(124mm)
3 3/8"
(86mm)
2 1/6"
(52mm)
7/8"
(22mm)
1/8"
(3mm)
9"
(229mm)
3 9/16"
(90mm)
Minimum
Clearance
1"
(25mm)
11/16"
(17mm)
1 3/8"
(35mm)
5/32"
1"
(25mm) (4mm)
5 3/8"
(137mm)
1 5/8"
(41mm)
3 7/8"
(98mm)
6"
(152mm)
6 1/8"
(156mm)
35/32"
(80mm)
Minimum
15/16"
Clearance
7
(24mm)2 /8"
(73mm)
3 3/4"
(95mm)
6 1/8"
(156mm)
Minimum
1 5/8" Clearance
(41mm)
5
1 1/4" /32"
(32mm)(4mm)
4 1/2"
(114mm)
Minimum
Clearance
1 7/16"
(37mm)
3 7/8"
(98mm)
1 1/4"
(32mm)
1 3/4"
(44mm)
6222
1 3/8"
(35mm)
1 15/32"
(37mm)
3 3/4"
(95mm)
3/4"
(19mm)
Minimum
Clearance
6214
1 1/4"
(32mm)
9"
(229mm)
5/32"
(4mm)
1 3/8"
(35mm)
1"
(25mm)
1 1/4"
(32mm)
6211WF
12 "(305mm)
Minimum
Clearance
6221
6213
1 1/4"
(32mm)
1 5/8"
(41mm)
3/4"
(19mm)
Minimum
Clearance 1 5/8"
(41mm)
3 3/4"
(95mm)
5 3/8"
(137mm)
9"
(229mm)
1 1/2"
(38mm)
1/8"
(3mm)
2 7/8"
(73mm)
1"
(25mm)
3 3/8"
(86mm)
6 3/8"
(162mm)
3 5/32"
(80mm)
2 1/16"(41mm)
2"
(51mm)
1 5/8"
(41mm)
3 3/4"
(95mm)
5
1 /8"
(41mm)
5/32"
(4mm)
2"(51mm)
1 5/8"
(41mm)
12"(305mm)
Minimum
Clearance
9"
(229mm)
1 5/8"
(41mm)
12"(305mm)
Minimum
Clearance
6200 Series strikes dimensions
7/8"
(22mm)
3 3/8"
(86mm)
2 1/16"
(52mm)
(4mm)
1 3/8"
(35mm)
4 1/2"
(114mm)
1 11/16"
(43mm)
4 7/8"
(124mm)
1 5/8"
(41mm)
6216
1 15/32"
(37mm)
1 1/4"
(32mm)
1 15/32"
(37mm)
(95mm)
11/16"
(17mm)
1/8"
(3mm)
1/2"
(13mm)
1/2"
(13mm)
(305mm)
9"
(229mm)
1"
(25mm)
7/8"
(22mm)
6211
1 1/4"
(32mm)
(38mm)
3 3/4"
(95mm)
1 3/8"
(35mm)
15
Von Duprin Door control and security hardware • 15
6200 Series strikes dimensions
Dimensions
6224AL
6223
1 1/4"
(32mm)
4 1/2"
(114mm)
1 3/8"
(35mm)
9"
(229mm)
3 7/8"(98mm)
3 7/8"
(98mm)
6"
(152mm)
6126
1 3/8"
(35mm)
1 5/8"
(41mm)
Minimum
Clearance
1 3/4"
(44mm)
1/4"
(6mm)
9"
(229mm)
1 5/8"
(41mm)
1 1/2"
(38mm)
1 5/8"
(41mm)
3 3/4"
(95mm)
1"
(25mm)
11/16"
(17mm)
12"(305mm)
Minimum
Clearance
5/32"
(4mm)
6225
2"
(51mm)
1 3/8"
(35mm)
1 1/2"(38mm)
2 1/16"(22mm)
1 5/8"
(41mm)
9"
(229mm)
3 3/4"
(95mm)
1"
(25mm)
1 5/8"
(41mm)
12"(305mm)
Minimum
Clearance
9"
(229mm)
1 5/8"
(41mm)
1 5/8"
(41mm)
5/32"
(4mm)
11/16"
(17mm)
1 3/8"
(35mm)
12"(305mm)
Minimum
Clearance
3 3/4"
(95mm)
5/32"(4mm)
Ordering information
3
4
5
Buzzer*
Voltage
2
Finish
Dual switch*
1
Rectifier kit*
Power
failure mode
6210-FSE -DS- 24 - S024 - US3 - EB
Model
6200 Series strikes dimensions
12"(305mm)
Minimum
Clearance
5/32"
(4mm)
11/16"
(17mm)
6224
3 3/4"
(95mm)
1 5/8"
(41mm)
1"
(25mm)
1"
(25mm)
1 3/8"
(35mm)
1 1/2"
(38mm)
1 5/8"
(41mm)
6
7
* Optional
Selections correspond with the numbers above
1Model
2
6210
6211
6211AL
6211WF
6212
6212WF
6213
6214
6215
6216
6221
6222
6223
6224
6224AL
6225
6226
FSE
Fail-secure. Requires power to be
applied to unlock the strike lip. On
loss of power, the strike lip is locked.
Fire-rated.
FS
Fail-safe. Requires power to be applied to lock the strike lip. On loss
of power, the strike lip is unlocked. Non-fire-rated.
See chart on page 13 to make the
proper selection
See chart on page 13 to make the
proper selection
See chart on page 13 to make the
proper selection
See chart on page 13 to make the
proper selection
See chart on page 13 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
See chart on page 14 to make the
proper selection
16• Von Duprin Door control and security hardware
16
Power failure mode
3
Dual switch (optional)
DS
DS-LC
Monitors latch bolt and lock status.
DS switches rated at 24 VDC
50 milliampere - 2 amps.
Optional for computer monitoring.
Monitors latch bolt & lock status.
DS-LS switches rated 24 VDC
50 milliampere or less.
4
Voltage (VDC)
24
Low voltage DC power
12 Low voltage DC power
If AC power is required, specify rectifier kit below.
5
Rectifier kit (optional)
SO12
S024
Converts 12 VAC voltage to 12 VDC
to operate the solenoid
Converts 24 VAC voltage to 24 VDC
to operate the solenoid
6Finish
US number/Von Duprin number
US3/85 Plated polished brass on
stainless steel
US4/84 Plated dull brass on stainless steel
US10/06 Plated dull bronze on stainless steel
US10B/86Plated dark bronze on
stainless steel
US32/31 Stainless steel, polished
US32D/32Stainless steel, satin
7
Buzzer (optional)
EB
Entry Buzzer. Only available if Fail-Secure (FSE) is specified.
6300 Series surface mounted strike for rim exit devices
Overview
Von Duprin electric strikes are known for their reliability,
durability and security. The 6300 Series is designed to withstand
abuse. Its heavy-duty stainless steel construction is fully UL1034
and UL10C Listed.
6300 Series electric strikes are designed for use with a variety of
rim devices. It interfaces with the latch mechanism of the exit
device. The movable lip (keeper) allows a door to open even
when the latch bolt is extended. This feature, called remote
release, provides added benefits such as increased convenience
and efficiency. The 6300 Series also provides added security
and traffic control.
The 6300 is fail-secure (FSE) only to achieve compliance with
UL10C for fire-rated openings. In a fail-secure application, the
door is normally locked. To unlock the door, power must be
applied. The 6300 strike can be used with either 12VDC or
24VDC. There are 2 connectors that ship with it and the
appropriate connector for either 12VDC or 24VDC will be used,
based upon the available voltage at the opening.
Features
§§ Non-handed design provides greater flexibility
§§ Requires no alteration or cutting to existing frame
6300 Surface mount specifications
Model
Voltage
Current
Duty
Amps
Ohms
6300
12V
DC
Continuous
0.50
22
6300
24V
DC
Continuous
0.24
89
Rim exit device compatibility 6300 strikes
Manufacturer
Model Number
§§ UL10C electric strike for fire door
Von Duprin
VD 22/22-F Rim
§§ Stainless steel (satin) finish
Von Duprin
VD 33A/35A Rim
§§ Durable stainless steel construction
Von Duprin
VD 55 Rim
§§ Field selectable voltage 12VDC or 24VDC
Von Duprin
VD 88/88-F Rim device
§§ Meets BHMA A156.31, Grade 1 for endurance and strength
Von Duprin
VD 98/99 and 98/99-F Rim
§§ Static strength 1300 lbs
Falcon
Falcon 24/24-F Rim
Falcon
Falcon 25/25-F Rim
Falcon
Falcon 19/19-F Rim
Falcon Doromatic
Falcon Doromatic 1790
Falcon Doromatic
Falcon Doromatic 2090
§§ UL1034 burglary-resistant and
§§ Dynamic strength 70 ft-lbs
§§ Endurance 1,000,000 cycles
Model specifications
Model #
6300
Retrofits model
N/A
Latchbolt throw
3
Face plate length
9"
/4"
Projection
3
Lockset
Rim exit device
# Doors
Single or pair with mullion
Door/frame type
Hollow metal, aluminum and wood
EB (entry buzzer)
Optional
Certifications
UL1034, UL10C
Application notes
Surface mounted electric strike ideal for aftermarket
applications. Strike designed for use with Von Duprin
98/99, however it can be used with most rim exit
devices.
6300 Series surface mounted strike for rim exit devices
6300 Series electric strikes are ideal for aftermarket
applications. It is easy to install without modifying or altering the
door frame. To assure the proper selection of an electric strike on
new applications, lockset compatibility charts are shown on the
next page. When using a lockset not listed or when retrofitting a
strike to an existing application, please contact Von Duprin
technical support for application assistance.
/4"
17
Von Duprin Door control and security hardware • 17
6300 Series dimensions
1-3/4"
3/4"
AC
(19.0mm)
(44.5mm)
HORIZONTAL
ADJUSTMENT
MOUNTING
HOLES
9"
8-1/4"
(228.6mm)
5-1/2"
(209.6mm)
1-5/8"
(139.7mm)
(42.0mm)
AC with buzzer
LOCK DOWN
HOLES
DC = Direct current
Continuous duty = Energized 1 min. or more
Note: W
hen using device not listed or when retrofitting a strike to an existing application, please
contact Von Duprin Technical Support for application assistance.
Ordering information
Rectifier
kit*
Buzzer*
6300-S024- EB
Model
6300 Series dimensions
DC
1
2
3
DC with buzzer
* Optional
1
Model
6300
Surface mounted strike for rim exit devices
2
Rectifier kit (optional)
S012
S024
Converts 12 VAC voltage to 12 VDC to operate the solenoid
Converts 24 VAC voltage to 24 VDC to operate the solenoid
3
Buzzer (optional)
EB
Entry buzzer
Standard features
§§ Power failure mode: Fail-Secure (FSE)
§§ Voltage: field selectable 24 VDC or 12 VDC
§§ Finish: stainless steel, satin (US32D/32)
18• Von Duprin Door control and security hardware
18
Electric Strike/Lock information
Finishes
US number BHMA number Description
US3
—
Plated polished brass
on stainless steel
US4
—
Plated dull brass on
stainless steel
84
US10
639
Plated dull bronze on
stainless steel
06
US10B
640
Wire size selection
Von Duprin
number
Current requirement at 24VDC
85
Plated dark bronze on 86
stainless steel
US32
629
Stainless steel,
polished
31
US32D
630
Stainless steel, satin
32
Length of wire run (in feet) 0-.5 Amp .5-1 Amp
1-2 Amp
2-3 Amp
0-100
18
18
18
18
100-200
18
18
18
16
200-300
18
18
16
14
300-450
18
16
14
12
450-600
18
16
12
NR
600-900
16
14
NR
NR
900-1200
14
12
NR
NR
NR — Not recommended
Cross reference
Strike/Lock mounting
# Doors
Frame materal(SGL
Faceplate length
DR)
Door material(BL DR)
Drop in replaces
Von Duprin:
6111
Rim device
6112
Rim device
Single1
All
6"
3031
Single
All
9"
6113
Rim device
Single
All
6"
Drop in
replaces
Folger Adam:
310-44
3011, 3021
6114
Rim nightlatch
Single
All
7"
310-55
6121
Rim device
Double-closed back
All
9"
310-4-1005
6210
Mortise
Single
HM/Alu
47⁄8"
6211
Mortise or cylindrical
Single
HM/Alu
47⁄8"
6211AL
Mortise or cylindrical
Single
Aluminum
47⁄8"
6211WF
Mortise or cylindrical
Single
Wood
47⁄8"
6212
Mortise or cylindrical
Single
HM/Alu
63⁄8"
6212WF
Mortise or cylindrical
Single
Wood
63⁄8"
3140
712
722
7326
3146
6213
Mortise or cylindrical
Single
All2
6"
6214
Mortise or cylindrical
Single
All3
9"
310-2 3/4
6215
Mortise or cylindrical
Single
All3
9"
310-2
6216
Mortise and deadbolt
Single
HM/Alu
9"
6221
Mortise or cylindrical
Double-open back
All
6"
6222
Mortise or cylindrical
Double-open back
HM/Alu
9"
6223
Mortise or cylindrical
Double-closed back
All
6"
3041, 42, 61, 62
310-3-1
3071, 72
310-2 3/4 OB
3091, 3092
6224
Mortise or cylindrical
Double-closed back
HM/Alu
9"
310-2 3/4
6224AL
Mortise or cylindrical
Double-closed back
Aluminum
9"
310-2 RF
6225
Mortise or cylindrical
Double-open back
HM/Alu
9"
310-2 OB
6226
Mortise or cylindrical
Double-closed back
HM/Alu
9"
310-2
Electric Strike/Lock information
1
Name
Includes double door with mullion.
Recommended on wood frames only if drop in replacement is needed for 3041, 42, 61, 62 on wood frames. Otherwise use 6211WF.
Recommended on wood frames only if drop in replacement is needed for 310-2 3/4, 310-2 on wood frames. Otherwise use 6211WF.
4
Strike lip area cutout is slightly larger than Folger Adam.
5
Surface applied strike. Mounting hole locations different from Folger Adam.
6
Wood frame horizontal solenoid location differs from Folger Adam. May require frame prep modification when retrofitting.
2
3
19
Von Duprin Door control and security hardware • 19
E996L Electrified Breakaway™ lever trim
E996L Electrified Breakaway lever trim provides remote locking and
unlocking capabilities while incorporating the patented Breakaway trim
design.
The 24VDC solenoid can be energized from a distant controller, thus
allowing access control of the opening. The control of stairwells in
high-rise buildings is a common application for this trim.
When electrically unlocked the unit operates as a normal lever trim.
When electrically locked, the lever feels locked, but when more than 35
pounds of torque pressure is applied, the Breakaway lever feature
engages.
E996L Electrified Breakaway™ lever trim
The E996L is provided standard in a fail safe (FS) condition, but can be
field converted to a fail secure (FSE) where allowed. The trim can be
ordered with a device, added to an existing 98/99 series device
application, or a conversion kit can be added to an existing 996L
Breakaway lever trim. On new construction applications, the E996L trim
will require less door prep.
The E996L is available with a blank escutcheon (BE) function, or with
cylinder operation for night latch (NL) function.
The E996L electrified trim replaces the current “E” electric feature on
98/99 series rim devices. Consult factory forrequirements.
To order, specify:
1. Use “E” prefix, example E996L.
When ordering with device specify trim series with “E”
prefix, example 9927L-BE 3´ US26D E996.
E996L Electrical wiring
§§ Power input for E996L is 24VDC
§§ Two wires on trim are non-polarized (18 AWG minimum)
Power Wire Runs Through
Exit Device Body
2. Device type, R/V (rim/surface or concealed vertical rod)
or M (mortise).
Power Supply
PS902
24 VDC
output
3. RHR is furnished standard if not specified. Field reversible.
4. Lever style (06 lever is furnished standard).
5. Finish: US3, US4, US10, US10B, SP313, US26, US26D, SPBLK, US15
Specifications
Solenoid – continuous duty 24VDC
Solenoid draw – 0.22 amp
20 Von Duprin Door control and security hardware
20•
E996L
Trim
Power Transfer
(EPT2 shown)
Control Switch
(normally closed)
Lever styles
Decorative Levers
M51
Knurling available
M52
Knurling available
M53
M54
M55
M56
M57 ••
M61
(Handed)
M62 ••
(Handed)
M63
(Handed)
M81
Knurling available
M82
M83
M84
M85
(Handed)
•• Available in Stainless Steel substrate ONLY.
Lever styles
Standard Levers
01
02
Knurling available
03*
Knurling available
05
06*
Default lever
Knurling available
07
12
(Handed)
16
(Omega)
17*
Knurling available
18
ACC
(Accent)
(Handed)
AST
(Asti)
(Handed)
MER
(Merano)
(Handed)
STA
(St. Annes)
(Handed)
LAT*
Latitude
LON*
Longitude
*Available in Stainless Steel - specify SS when ordering
21
Von Duprin Door control and security hardware • 21
EL/QEL Electric latch retraction
QEL Quiet electric latch retraction
EL Electric latch retraction
The EL feature allows for the remote unlatching of exit devices. A
control station operator can flip a switch to retract the latch bolt
and immediately change an exit door to push-pull operation. A
powerful, continuous duty solenoid retracts the latch bolt, either
for momentary unlatching, or for extended periods of time. The
EL feature is an alternative to manual dogging.
If manual hex-key dogging is required, specify HD-EL. If cylinder
dogging is required, the standard cylinder dogging is not
available, but special center case dogging is available, specify
SD-EL. SD-EL is not available on the 9875 or 9975 devices.
EL devices are also useful with automatic door operators, and
may be applied to fire-rated applications when under the control
of an automatic fire alarm system.
UL approved for Class II circuit applications.
EL Signal switch
The EL option does not include the power transfer from door to
frame, the power supply, or the control operator. Refer to EPT-2
power transfer and the PS914 power supply.
The PS914 with the 9002RS option card is the minimum option
card required. Other option cards available for other functions,
see PS914 power supply for additional information.
Solenoid specifications:
Continuous duty – 24 VDC
Current inrush – 16 Amps
Current holding – 0.3 Amps
Solenoid resistance:
-grn-yel 1.2 – 2.2 OHMS
-grn-org 100 – 150 OHMS
To order, specify:
PS872 Wiring
Standard – use prefix EL, example EL99L.
Hex Key dogging – Use prefix HD-EL, example HD-EL99L
special center case dogging – Use prefix SD-EL, example
SD-EL99L
Popular EL application
Power supply PS914-2RS
Electric power transfer EPT-2 or EPT-10
The QEL feature allows for the remote unlatching of exit devices.
A control station operator can flip a switch to retract the latch
bolt and immediately change an exit door to push-pull operation.
Different than the popular EL, the QEL quiet operation is
achieved using an electric drive motor which retracts the latch
bolt either momentary unlatching or for extended periods of
time. This feature is an alternative to manual dogging.
If cylinder dogging is required, the standard cylinder dogging is
not available, but special center case dogging is available,
specify
SD-QEL. SD-QEL is not available on the 9875 or 9975 devices.
QEL devices are also useful with automatic door operators, and
may be applied to fire-rated applications when under the control
of an automatic fire alarm system.
UL approved for Class II circuit applications.
The QEL option does not include the power transfer from door to
frame, the power supply, or the control operator. Refer to EPT-2
power transfer and the PS902 or 914 power supply.
The PS902/914 with the 2RS, 4RL or 4R board is the minimum
required. Other option boards available for other functions, see
PS902/914 power supply for additional information.
The QEL has a low in rush current, so it can be used with
standard Schlage power supplies. Calculate the peak current
draw of all devices in the system to determine the required
amperage of the supply.
QEL Electrical load
Voltage
24VDC
Current
1.0 A Inrush (0.5 sec.) / 0.14 A Holding
The 900-2RS option board designed to control two electric latch
retraction devices and provide time delay between the firing of
outputs is required. The power transfer is also sold separately.
Schlage PS902
Schlage PS904
Schlage PS906
up to 2 amps
up to 4 amps
up to 6 amps
PS872 Wiring
To order, specify:
Standard — use prefix QEL, example QEL99L.
Special center case dogging — use prefix SD-QEL,
example SD-QEL99L
120/240
VAC
SC I1 O1 I2 O2 GND
Popular application
Power supply PS902-2RS
Electric power transfer EPT-2 or EPT-10
EPT-2
EL #2
a*
Input #2
120/240
VAC
(Required for
independent
operation only).
b*
SC I1 O1 I2 O2 GND
EPT-2
QEL #2
EPT-2
a*
EL #1
a*
EL 98/99 Rim
EL 33A/35A Rim
a*
b*
All other 98/99EL
and EL33A/35A
device types
Control Switch
(Required for
independent
operation only).
b*
Input #1
b*
Von Duprin
exit device
Input #2
EPT-2
EL Wire
length (feet)1
Wire gauge
(AWG)
0-500
0-300
0-200
0-250
0-150
0-100
0-1200
12
14
16
12
14
16
18
1. Wire lengths include an EPT, Door loop, electric hinge or pivot and are
measured one way between the PS914/option board and the device.
2. Table is applicable to devices that have shipped after August 2012.
22 Von Duprin Door control and security hardware
22•
QEL #1
a*
Input #1
b*
a*
b
*
Distance (one-way)
200´
Wire gauge
18 AWG
320´
16 AWG
500´
14 AWG
800´
12 AWG
Wire selection
1200 ft. Max.
Switch wire size
18 gauge standard
RX/LX Switches
LX33A/LX35A
RX33A/RX35A
LX98/LX99
RX98/RX99
Rim device shown — Refer to 33A/35A or 98/99
series catalog for complete product information,
mounting styles, outside trim, finishes, etc.
RX Request to exit
The RX (2xit) feature is used to signal the use of an opening.
This device is equipped with one internal SPDT switch which
monitors the pushpad.
LX Latchbolt monitoring
The device can be connected to a security console, or may be
used as a single door alarm when used with a horn and power
supply.
The RX switch option should not be used to control a load, but
as a signalling switch (0.5 amps. resistive maximum).
The RX switch is available in a low current (LC) switch. Most
commonly used in computer operated monitoring systems.
To order, specify:
§§ Standard – Use prefix RX, example RX99EO
Low Current – Use prefix RX-LC, example RX-LC98EO
RX2 Double request to exit
To order, specify:
§§ Standard – Use prefix RX2, example RX299EO
WP-RX Waterproof request to exit
The device can be connected to a security console, or may be
used as a single door alarm when used with a horn and power
supply.
The LX switch option should not be used to control a load, but as
a signalling switch
(0.5 amps. resistive maximum).
The LX switch is available in a low current (LC) switch. Most
commonly used in computer operated monitoring systems.
To order, specify:
§§ Standard – Use prefix LX, example LX99EO
§§ Low Current – Use prefix LX-LC, example LX-LC98EO
Electrical rating for all switches:
§§ Standard – 2 Amp maximum @ 24VDC
§§ Low Current (LC) - below 50 Milliamps @ 24VDC
Note: All switches can be either factory or field installed
RX/LX Signal switch
The RX2 feature uses two RX switches.
The LX feature is used to signal the use of an opening. This
device is equipped with one internal SPDT switch which
monitors the latch bolt.
23
23
Von Duprin Door control and security hardware • 23
SS Signal switch
Monitors pushpad and latch bolt
The SS feature is used to signal the unauthorized use of an
opening. This device is equipped with two internal SPDT
switches. One switch monitors both the pushpad and the latch
bolt assembly, making the latch bolt tamper resistant, for
positive security. An additional SPDT switch is connected to the
1 1/4" (32mm) mortise cylinder with straight cam for alarm
“bypass.” (Schlage cam reference B502-191). The device can be
connected to a security console, or may be used as a single door
alarm when used with a horn and power supply.
SS Signal switch
Pushpad reads: “Emergency Exit ONLY – Push To Open And
Sound Alarm.” Pushpad is only available in US32D finish with red
silk-screened lettering.
The SS mortise lock device is furnished with both the signal
switch device and the SS7500 mortise lock. The SS7500 mortise
lock has the versatility and advantages of the 7500 lock with the
addition of signalling functions to monitor latch bolt operation
and the trim locking function. The SS7500 mortise lock is
supplied standard with the SS mortise lock device.
To order, specify:
1. Prefix SS, example SS99L.
2. Handing required, LHR or RHR.
Electrical ratings:
Up to 2.0 AMPS @ 24VDC
24 Von Duprin Door control and security hardware
24•
Popular SS Application
Unauthorized use of this opening will activate the local horn. The
key switch permits inhibiting this ­system for authorized entry.
RX330/RX350 Push pad
RX330
RX330 and RX350 bar features an active push pad with
monitoring switch or “request to exit” switch, used to inhibit
alarms for authorized exiting. The 330 grooved outer case and
the 350 smooth outer case are designed as companion units for
series 33A, 35A, 98 and 99 exit devices.
Minimum door openings:
The RX switch option is also available on 55DU and 88DU
crossbars, and are designed as companion units for series 55 and
88 exit devices.
1. Prefix series 330 or 350 with “RX”.
The internal SPDT switch should not be used to control a load,
but as a signaling switch.
3' (914mm)
2'6" (762mm) to 3' (914mm)
4' (1219mm)
3'1" (940mm) to 4' (1219mm)
To order, specify:
Example, RX330
2. Size 3' or 4' (3' supplied standard if size not specified)
3. Finish: US3, US4, US10, US28, US26, US26D, 313AN, 315AN
SPDT 0.5 ampere @ 24VDC Solenoid draw - 0.22 amp
RX
Yellow
Red
Blue
RX330/RX350 Signal switch
Specifications
25
Von Duprin Door control and security hardware • 25
CX The Chexit®
Door position input: An external door position switch can be
connected to the Chexit.
Using the door position input ensures that the door is in the
closed and latched position before the device rearms.
Designed for use on delayed exit applications, the Chexit ­system is
ideal for controlled areas.
All controls, auxiliary locking, local alarm, and remote signalling are
self-contained in the Chexit, providing safe, secure, easy to install
and simple to operate door control and exit hardware.
Chexit controlled exit device for use on panic or fire exit hardware
applications.
This concept in delayed exit systems combines life safety with the
needs of security and meets all requirements of NFPA 101 for
“special locking arrangement.”
The Chexit device includes a 6" x 20" decal for application on door.
“PUSH UNTIL ALARM SOUNDS.
DOOR CAN BE OPENED IN 15 SECONDS”
Alarmed exit devices
Minimum width door opening:
§§ 3' Device 34" opening
§§ 4' Device 40" opening
Consult factory for other size requirements.
Solenoid specifications:
§§ Continuous duty – 24VDC
§§ Current inrush – 16 amperes
§§ Current holding – .3 amperes
Requires PS914 Power Supply
Request to exit switch: Built into the device to detect when
someone attempts to exit. Pushing the push pad when the device
is armed will cause this switch to start an irreversible alarm cycle.
Nuisance alarm: When a Chexit is located in a public area, it can be
desireable to limit false alarms. If the Nuisance Delay options are
set to off, the device will go into alarm as soon as the push pad is
touched (when armed). Turning the Nuisance Delay on will require
the push pad to be pressed for 1 second before the Chexit goes into
alarm. If the Nuisance Audible and Nuisance Delay are both on, the
alarm will sound as soon as the push pad is pressed, but the alarm
sequence will stop unless the push pad is held for 1 second or more.
External inhibit input: This optional input is provided to allow
authorized egress of the Chexit in the armed condition. It also
allows remote reset of the Chexit in an alarmed condition.
Fire alarm input: This input disables the Chexit immediately
upon a fire alarm.
Internal auxiliary lock: The Auxiliary Lock is engaged when the
Chexit is armed. The locking mechanism is specifically designed
to hold securely even when the exit device is struck with forceful
blows.
User defineable rearm time: The Rearm time is the amount of
time after the device is activated before it arms. It is designed to
give someone time to pass through the door before rearming
oocurs. Timing can be changed by the user for any time between
2 and 28 seconds in two second increments. There is also an
infinite rearm setting that requires the use of an external door
position switch. In this setting the door remains in the rearm
mode until the door is closed. This can be useful on jet way doors
in an airport.
Factory defineable delay time: Most jurisdictions allow 15
seconds of delay before allowing egress. In those cases where 15
seconds is not appropriate, Von Duprin can set the Chexit for any
delay time between 0 and 60 seconds on 2 second increments.
For delays greater than 15 seconds a letter from the local
authority is required.
Chexit typical application
Chexit single door with options – The Chexit is used as an
access control device. The card reader allows access. Also
shown in this application is an external horn and door position
switch. The auxiliary horn is used for increased volume in
remote locations. Using a door position switch gives added
security to the opening in case the door is not reclosed.
With the Chexit disarmed, the opening functions as a normal
exit device. If card readers are required on both sides of the
door, the normally closed contacts of the readers should be
weird in series.
120 VAC 3 x 14 ga.
2 x 12 ga.
Power Supply
To Fire Alarm 2 x 18 ga.
2 x 18 ga.
Remote alarm: A relay contact is provided to give external alarm
indication. This contact close when the device is in an irreversible
alarm condition. This contact can be used to drive a horn, lamp, or
other indicative device.
Horn
2 x 18 ga.
(new)
EPT
KPT-10
Key switch: The Key switch provides the means to arm, disarm or
reset the Chexit. The key can be removed in either the Arm or
Disarm position.
Chexit mortise lock device
the outside trim works
independently from the
Chexit device.
Cable
Card
Reader
(Inside or
Outside)
Indicator lamp: The status of the Chexit can be determined by the
indicator lamp. When the lamp is off, this indicates the device is
disarmed and is functioning as a normal exit device (no delay). A
continuously on lamp indicates the device has just been armed and
as soon as the selectable rearm timer expires, the device will arm.
A slow flashing lamp indicates the device is armed. A fast flashing
indicator lamp indicates the device is in alarm.
Chexit
Gnd
+24
PS914
Power Supply
Fire Alarm
Internal horn: Whenever the device is in alarm or the push pad is
pressed the internal horn will sound. The volume level of this horn
exceeds 85 db at 6 feet.
Door Position
Switch
Card Reader
–
26 Von Duprin Door control and security hardware
26•
2 x 18 ga.
2 x 12 ga.
6 x 18 ga.
+
Horn
Note: Chexit rim or vertical
rod/cable devices lock any
outside trim input when the
device is in the armed
condition. If access is
needed from the trim side
of the door, some type of
electric switch would need
to be tied into the external
inhibit input of the device.
+24
Red
Gnd
Black
SC
White
FA
Yellow
DPS
Orange
III
Green
CM+
Gray
CM-
Violet
NO
Brown
C
Chexit
Cable
Blue
CX The Chexit®
To order, specify:
1. Prefix product description number “CX”.
Example: CX99L
2. D
oor size other than 3' (914mm).
3. Door thickness other than 1 3/4" (45mm).
4. Finish.
5. H
anding, LHR or RHR. Required with “CD” option.
Options
RCM Remote Chexit Module — is designed to provide the
concept of the Chexit delayed exit system for door sizes smaller
than the standard Chexit device can accommodate. The Chexit
module is installed in a control box and mounted in a remote
location. Features and functions of the standard Chexit exit
device are available on the Remote Chexit Module.
Cylinder dogging — Special center case cylinder dogging option
is available to allow push/pull operation of the Chexit, when
disarmed and used in a heavy traffic area. Prefix device with “CD”
and specify handing.
Cylinders — Cylinders are not furnished with the Chexit device
and must be specified when ordering. Uses a standard 1 1⁄ "
(32mm) mortise cylinder for the device and the CD cylinder
dogging option.
4
RCM Control
box, lens, cover
Door width reference for CX devices
Device
3' (914mm)
Length
4' (1219mm)
Length
CX33A/35A/33A-F/35A-F
2'10 1/2" (864mm)
3'4 1/2" (1016mm)
CX98/98-F/99/99-F
2'10 1/2" (864mm)
3'4 1/2" (1016mm)
CX9875/9875-F/9975/9975-F
2'10" (864mm)
3'4" (1016mm)
CX9827/9827-F/9927/9927-F
2'10" (864mm)
3'4" (1016mm)
CX9857/9857-F/9957/9957-F
2'10" (864mm)
3'4" (1016mm)
CX9847/9847-F/9947/9947-F
2'10" (864mm)
3'4" (1016mm)
CX9848/9848-F/9948/9948-F
2'10" (864mm)
3'4" (1016mm)
CX9849/9849-F/9949/9949-F
2'10" (864mm)
3'4" (1016mm)
CX9849/9849-F/9949/9949-F
2'10" (864mm)
3'4" (1016mm)
CX-R 33A/35A
2'4" (838mm)
2'10" (1041mm)
CX-R 98/9927
2'4" (838mm)
2'10" (1041mm)
CX-R 98/9947
2'4" (838mm)
2'10" (1041mm)
CX-R 98/9947-F
2'5" (864mm)
2'11" (1016mm)
CX-R 98/9947WDC
2'5" (864mm)
2'11" (1016mm)
CX-R 98/9975
2'5" (864mm)
2'11" (1016mm)
Alarmed exit devices
RCM Module
27
Von Duprin Door control and security hardware • 27
Alarmed exit devices
The DE5101, like the Chexit system, is used on delayed exit
application and is ideal for controlled areas. This concept in
delayed exit systems combines life safety with the needs of
security and meets all requirements of NFPA 101 for “Special
Locking Arrangement.”
The DE5101 is commonly used on narrow stile doors where a
standard or narrow stile Chexit is not practical. DE5101 Delayed
Exit System uses a Chexit logic board and a Von Duprin RX
(request to exit) panic device to control a Locknetics Direct Hold
Magnetic Lock.
The Chexit module for the DE5101 is installed in a control box and
mounted in the wall adjacent to the door. Features and functions
of the standard Chexit exit device are available on the DE5101
(see page 22).
Size: 3.75" x 5.57" x 2.50"
Cylinders — Cylinders are not furnished with the DE5101 system
and must be specified when ordering. Uses a standard
1 1⁄4" (32mm) mortise cylinder for the control.
(Schlage cam - B502-191)
Specifications
To order, specify:
Fire alarm input, external inhibit input, door position input –
set-up for normally closed dry contacts.
1. DE5101
Continuous duty – 24VDC
Current holding DE5101 without magnetic locks – 300 mA
External alarm contact – 1 ampere @ 24VDC
2. M
420, M450, or M490 magnetic lock (order direct
from Schlage Electronics).
3. RX22/33A/35A/98/99 device.
4. PS900 Series
5. EPT-2/10
JUNCTION
BOX
NO
DSM
C
NC
320, 350,
OR 390
MAGNETIC
LOCK
GRN
ORG
YEL
RED
WHT
GRN
YEL
ORG
BLU
BRN
GRY
VIO
DE5101
BLK
ORG
ORG
120 VAC
1 AMP
GND
NEU
HOT
FIRE
ALARM
CONTACT
NC
TO
FIRE ALARM
PANEL
2X18
10X18
2X18
EPT-2
RX DEVICE
YEL
RED
BLU
RX
GND
+24
28 Von Duprin Door control and security hardware
28•
EPT-2
OR
UL APPROVED
ELECTRIC HINGE
840
3X14
JUNCT. BOX
DE5101
PS914
2X18
4X18
Alarmed exit devices
The DE5101 includes decal for application on door.
“PUSH UNTIL ALARM SOUNDS. DOOR CAN BE OPENED IN 15
SECONDS”. This is a code based requirement.
MAGNETIC LOCK:
USE LOCKNETICS
320, 350 OR 390
120 VAC
1 AMP
ALK Alarm kit
ALK Alarm kit is a simple yet effective way to deter unauthorized
use of an opening. While the exit device is still a means of egress,
the ALK kit contains an internal horn. When the touch bar is
depressed, the horn sounds to provide an audible means of
signaling that the opening has been violated. The alarm kit can
be armed or disarmed by key thus allowing the exit device to be
set in an armed or disarmed mode. The horn is rated at 85
decibels.
For Hardware Applications
The assembly includes both a 24VDC Input and External Inhibit
standard. The External Inhibit provides remote arming and
dis-arming.
The alarm can automaticaly re-arm with a 1 1/2, 3 or 4 1/2 minute
time delay upon request.
Alarm kits are available with a choice of two switch kits, RX or
LX. RX monitors the touchpad and is furnished standard. LX
optional latch bolt monitoring is recommended for use with
surface vertical rod exit devices or when alarm needs to sound
from both the exit device and trim side of the door. Specify
ALK-LX.
Note: For latch bolt monitoring on a 98/9975 with ALK, specify a SS7500 lock. LX switch
not available for 98/9975 devices.
ALK Alarm kit is a simple yet effective way to deter unauthorized
use of an opening. While the exit device is still a means of egress,
the ALK kit contains an internal horn. When the touch bar is
depressed, the horn sounds to provide an audible means of
signaling that the opening has been violated. The alarm kit can
be armed or disarmed by key thus allowing the exit device to be
The ALK includes a 6" x 20" decal for application on door
“EMERGENCY EXIT ONLY. ALARM WILL SOUND.” RSS push bar
trim can be used instead of the door decal, specify RSS push bar
trim when ordering the device.
When the ALK is used, standard dogging is removed. If cylinder
dogging is required there are two choices. Special center case
dogging is available or for 3' or 4' doors. The ALK can be moved
to the hinge side of the device and standard cylinder dogging can
be added.
To Order, Specify:
1. Standard, 98 ALK
2. Cylinder Dogging, CD98 ALK
3. Special center case dogging, SD98 ALK (98/99 Series only)
4. If AR desired, specify AR 1.5, 3 or 4.5
Minimum door opening sizes on ALK applications
Device
3' (914mm)
Length
4' (1219mm)
Length
98/98-F/99/99-F
2'10" (864mm)
3'4" (1016mm)
9875/9875-F/9975/9975-F
2'10" (864mm)
3'4" (1016mm)
9827/9827-F/9927/9927-F
2'10" (864mm)
3'4" (1016mm)
9857/9857-F/9957/9957-F
2'10" (864mm)
3'4" (1016mm)
9847/9847-F/9947/9947-F
2'9" (838mm)
3'3" (991mm)
9848/9848-F/9948/9948-F
2'9" (838mm)
3'3" (991mm)
Device
3' (914mm)
Length
4' (1219mm)
Length
33A/35A
2'9" (838mm)
3'3" (991mm)
3327A/3527A
2'8" (813mm)
3'2" (966mm)
3347A/3347A-F
3547A/3547A-F
2'8" (813mm)
3'2" (966mm)
3348A/3348A-F
3548A/3548A-F
2'8" (813mm)
3'2" (966mm)
ALK Battery alarm kit
The key switch uses a standard 1 1/4" (32mm) mortise cylinder
with a straight cam (Schlage 20-001, B502-191 cam). The unit
operates on one standard 9-volt alkaline battery. When the
battery is weak, the horn will emit an intermittent low battery
alert signal.
The ALK is available in two styles, 33A/99ALK, grooved cover
and 35A/98ALK, smooth cover.
Minimum door sizes
29
Von Duprin Door control and security hardware • 29
GUARD-X Exit alarm lock
2670 GUARD-X provides secure, alarmed code-compliant
protection for secondary emergency exits. The GUARD-X exit
alarm lock readily identifies the door on which it is mounted as
an emergency exit and secures the ­opening against unauthorized
use. It is ideal for deterring theft in restaurants and retail
establishments such as: discount stores, grocery stores, drug
stores, clothing stores and sporting goods stores.
GUARD-X Exit device
The GUARD-X lock provides secure protection through a large
stainless steel deadbolt, which is 2" x 1⁄2" (51mm x 13mm) and
has over 3⁄4" (19mm) throw. The engagement area into the strike
is over 1 1⁄4" (32mm) square inches. The cast aluminum latch
case protects the internal mechanism and resists tampering or
vandalism from inside the door. This unit has been tested to
withstand up to 1600 pounds of static load force against the
door.
GUARD-X does not allow re-latching or resetting the alarm after
an unauthorized exit, other than by an authorized person with a
key. A 100-decibel alarm provides clear, attention getting
warning for an unauthorized exit or attempted exit. The armed
indicator light informs the owner that the alarm is armed, and an
audible low-battery alert signals the owner to replace the battery
when necessary.
The GUARD-X non-handed design means the installer can
mount it for either hand by just removing and reversing the
“EMERGENCY EXIT – ALARM WILL SOUND” sign built into the
device. The standard warning sign is in English with Braille;
French and Spanish are available.
GUARD-X is UL/cUL listed for Panic Exit Hardware, complies with
NFPA 101 Life Safety Code, meets UL305 requirements and is
tested in accordance to ANSI A156.3 Grade 1 Panic Hardware. It is
compliant with NFPA 101 Life Safety Code by providing a push
pad that extends at least one-half the width of any door up to
48" wide. The impact-resistant end caps meet UL305
requirements by providing a design that will not catch on
clothing during egress.
To order, specify:
1. Model 2670
2. Finish: US28, 313, 315.
3. Strike if other than standard 267.
4. Language if other than English.
5. Specify Rim Cylinder or Sex Bolts if required.
6. O
utside trim if needed.
A standard 9-volt battery powers the alarm. An exterior 9-volt
power supply is available, Model PT-790, a 120VAC plug-in.
When using the external power supply, the 9-volt battery
functions as a battery backup during a power failure.
GUARD-X is armed and disarmed by key using a standard rim
cylinder. It can be operated from the building exterior by a
standard rim cylinder, so an authorized user can easily arm and
disarm it to enter or exit the building when required. When using
exterior operation a pull trim is recommended, use 210DT or
230DT. Rim cylinders are not furnished and must be ordered
separately.
The 267 strike is furnished standard for single door applications.
The optional 2609 strike is available for double door
applications.
Touchbar height
to finished floor
2 3/4"
(70mm)
40" (1016mm) at center
Door width range 36" (914mm) to 48" (1219mm)
Touchbar
projection —
neutral
4 1/8" (103mm)
depressed
2 3/4" (70mm)
Latch case
housing
7" (179mm) x 4 1/16" (103mm) x 4 1/8" (105mm)
Device length
32 1/2" (826mm)
Minimum stile
requirement
Single door - 5 7/8", Double door - 6 1/4"
Note: Von Duprin trim does not thru-bolt to the Guard-X. Ives door pulls 8102-6 and
8105-6 offer dimensions that align and thru-bolt to the Guard-X Exit Lock - Order
separately from Ives.
30 Von Duprin Door control and security hardware
30•
4 1/16"
(109mm)
7"
(179mm)
4 1/8"
(105mm)
Y
ONL
T
I
EX D
NCIYLL SOUN
E
G
W
R
EME LARM
A
32 1/2"
(826mm)
E7500 Electric mortise lock
Allegion Connect
The electric mortise lock device has all the versatility and
advantages of the standard mortise lock device, plus the
advantage of being electrically controlled by a remote switching
device, an access control system or an automatic fire alarm
system. The device features the E7500 mortise lock. The E7500
controls the locking of the outside trim. When unlocked, the door
remains latched, preserving the fire rating of the door and making
it particularly useful where codes permit locking but require
unlocking during a fire emergency. The outside trim cylinder
retracts the latch bolt for mechanical override, night latch
function. Only available with TP, K or L functions.
Standard features:
§§ Field reversible handing
§§ 24 VDC continuous duty solenoid
Optional features:
§§ Fail safe (locked when energized, unlocked when de-energized
or during power failure). Specify with suffix “FS.”
§§ Fail secure (unlocked when energized, locked when deenergized or during power failure). Specify with suffix “FSE”
Features and benefits
•
Quick: common connections reducing installation time
•Perfect Connections: these factory installed connectors
ensure the right wires match up every time
•Protective: the connectors protect the connection points
throughout the installation process and lifetime of the opening
•Interchangeable: all Allegion Connect products utilize the
same connectors
•Maintenance: you no longer need to cut away wire to
disconnect Allegion products, also available is a service kit
specifically for Connect products.
§§ 24 VAC (with SO option)
Harness length
§§ 12 VDC
6 Inches
12 Inches
26 Inches
32 Inches
38 Inches
44 Inches
50 Inches
192 Inches
§§ 12 VAC (with SO option)
Note: Some Fire codes will require “Fail Safe” (FS) operation for stairwell doors.Be sure to
specify the correct operation for your application.
Electrical specifications:
§§ Solenoid — .60 AMPS @ 12VDC
.30 AMPS @ 24VDC
§§ Each switch — Up to 2.0 AMPS @ 24VDC Maximum
The E option does not include the power transfer from door to
frame, the power supply or the control operator. (Refer to EPT-10
and PS902 or PS914 power supply)
Connectors
on both ends
CON-6
CON-12
CON-26
CON-32
CON-38
CON-44
CON-50
CON-192
Connectors on one end,
crimped pins on the other end
CON-6P
CON-12P
CON-26P
CON-32P
CON-38P
CON-44P
CON-50P
CON-192P
Power Supply Wire Harness = Connectors on one end, stripped leads on the other end,
offering a direct connection to the power supply
6 Inches
CON-6W - wire extension to power supply
Consult door manufacturer for harness length requirements.
To order, specify:
1. Use prefix “E,” example E9975.
Note: You will need to purchase a separate wiring harness to go from exit device to hinge/
EPT and an additional harness to go from hinge/EPT to power supply or access control
system. Harness part numbers with ordering information can be located in the Schlage,
Von Duprin and Falcon pricebooks. A service kit is available for order in the Schlage, Von
Duprin and Falcon pricebooks. Included in this kit are male end plugs, female end plugs
and pins to customize harnesses to your application.
2. FS or FSE
Note: Must be ordered with exit devices and locks
3. Voltage and current.
E7500 Electric mortise lock
The E7500 lock contains a SPDT signal to monitor the outside
trim condition (locked or unlocked) and a second SPDT signal
switch to monitor the latch bolt.
Allegion’s cross-category Connect features common interconnect
components to our electrified options. Allegion Connect is a quick
and easy way to connect power sources; all the way from your
power supply to locking device. There is no wire cutting; reducing
installation and maintenance time ultimately cutting cost. After
installation, Allegion’s Connect continues to provide benefits
throughout the lifetime of the opening by offering a service kit
for repairs or modifications in the future.
How to order
1.Specify CON for Connect electronic options
Example: EL-99-EO-CON (99 Series Electrified Latching exit only
with Connect connectors)
2.Specify harness length; Consult door manufacturer for harness length
Electric mortise lock device
Adaptable for openings where ­continuous latching is required
while the trim may be electrically locked or unlocked from a
remote location—stairwells, exterior doors, etc.
3.Specify Von Duprin EPT10-CON or Ives 7200 power transfer hinge
Wire run options
Minimum system requirements:
§§ PS902
§§ EPT-10
31
Von Duprin Door control and security hardware • 31
Electrical options
Power Supplies
Series PS902/914
PS902 PS904 PS906 PS914
Number of connectors on
power supply for the
following:
2 amps 4 amps 6 amps 4 amps
Distribution boards
1
2
3
2
Battery back-up board
1
1
1
1
Note: One fire alarm board can be connected directly to the PS902. If a fire alarm board is
desired for the PS904, PS906 or PS914 it can be connected to
a distribution board.
Electrical options & accessories
Overview:
The PS900 Series is a consolidated line of power supplies and
accessories that offer enhanced flexibility and functionality
specific to the changing needs of the access control market. The
PS900 Series can be used in a variety of applications to convert
high voltage AC power into the low voltage DC outputs required
by most access control devices. The PS900 Series protects
devices downstream by providing Class 2*, filtered and regulated
power. The full line is UL294 certified.
Note: PS906 can provide Class 2 rated outputs when used with 900-8P distribution
board.
Features:
§§ Constant output rating at both 12 VDC and 24 VDC provides
superior performance ; includes field selectable jumper
§§ Polarized connectors for option boards eliminate need for
racks and side connectors
§§ Flat mounting of option boards provides easier access to
terminal blocks for connection of electrified devices
§§ High voltage protective cover
§§ Battery back-up board auto-selects voltage
§§ Fire alarm relay can be configured to provide either switched or
un-switched outputs from a power supply
§§ PS914 designed with high in rush current for powering
electrified panic devices
Applications:
The PS900 Series of power supplies works with many electrified
devices including Schlage electromagnetic locks, Schlage
AD-Series hardwired locks, Schlage electrified mechanical locks,
Von Duprin electrified strikes , Von Duprin exit devices, and many
other brands.
Accessories:
The Schlage PS900 Series features seven option boards for use
in a variety of applications. All Schlage PS900 Series power
supplies option boards are UL 294 certified.
Option boards:
900-4R: 4 relay controlled output board to power multiple
devices
900-4RL: 4 relay distribution board with logic is field
configurable for time delay function, auto operator, security
interlock
900-8F: Provides 8 individually fuse-protected outputs, giving
the flexibility to power multiple devices and provide another layer
of protection
900-FA: Emergency interface relay integrates with fire alarm and
is used to cut power in case of emergency
900-BB: Battery backup
§§ Universal 120-240 VAC input
900-2RS: 2 relay EL panic device control board (PS914 only)
§§ Low voltage DC, regulated and filtered
900-BBK: Battery backup kit includes two 7A/hr batteries and
provides up to four hours of backup power when cycled every 5
minutes at full load
§§ Electronic power limiting foldback circuit for AC current
overload protection
§§ Fused primary input
§§ AC status monitor- isolated SPDT contacts
§§ AC input and DC output LED status indicators
§§ Cover mounted AC input indication
§§ Hinged cover with lock down screws
Certifications:
§§ UL 294 certified—the standard for access control
§§ Class 2 rated*
* Except PS906, output rating exceeds Class 2 power limits
Once power is converted to low voltage DC, the PS900 Series
offers a variety of distribution options, including basic fuse
protection, simple relay, and advanced logic providing complex
sequencing and timing functions.
* PS906 can provide Class 2 rated outputs when used with 900-8P distribution board.
32• Von Duprin Door control and security hardware
Electric power transfer accessories
EPT Electrical power transfer
PNT Pneumatic transfer
Electric Power Transfer provides a means
of transferring electrical power from a
door frame to the edge of a swinging
door. The units are completely concealed
when the door is in the closed position,
and are ideal for installations involving
abuse or heavy traffic.
Two models are available; EPT-2, two 18 gauge wires and EPT-10,
ten 24 gauge wires. The EPT-2 and EPT-10 are U/L listed as
“miscellaneous door accessory”.
UL Listed for use on firedoors
Electromagnetic locks
Schlage has a rich heritage in electronic security. For years we
have led the industry by providing a broad portfolio of solutions
to meet the diverse needs of the market. Today, our
electromagnetic locking portfolio continues to evolve to meet
your changing needs.
Schlage electromagnetic locks are used to secure the door in
conjunction with push bars, request to- exit devices, or credential
readers for fail-safe applications when code compliance permits.
You can use them on a single standalone door or as part of an
access control system. Electromagnetic locks do not contain
moving parts, making them extremely durable and preferred for
high security applications.
6" butt hinges – 110˚ swing,
M400 Series electromagnetic locks
Door applications:
up to 5" butt hinges – 180˚ swing,
/4" butt offset pivots 180˚ swing.
3
Not for use with swing clear hinges or center-hung pivots.
Finishes
The M400 Series is a robust line of electromagnetic locks with
unique new design elements that make them easy to install and
secure.
Features:
SP28 (sprayed aluminum)
§§ Auto voltage selection is standard
SP313 (sprayed duranodic).
§§ Plus Package (P) adds magnetic bond sensor, relocking time
delay, door status monitor
Dimensions
§§ Optional mounting kits available including: Top Jamb Mount,
Double and Glass Door
Housing
9" x 1 1/4" x 1 5/8" (229mm x 32mm x 38mm)
EPT-2
Two 18 gauge wires, Up to 2 AMPS @ 24VDC, with
a 16 AMPS Maximum Surge
§§ UL 1034
EPT-10
Ten 24 gauge wires, Up to 1 AMPS @ 24VDC, with a
16 AMPS Maximum Surge
§§ BHMA Grade 1
PNT-1
5
/32" Tubing
To order, specify:
1. EPT-2 ,EPT-10 or PNT-1.
2. Finish, SP28 or SP313.
Certifications:
§§ UL 10C 3 hour fire rating
- M420 – 500 lb. hold force for traffic control
- M450 – 1000 lb. hold force for high security
- M490 – 1500 lb. hold force for max security
Electromagnetic specialty locks
Schlage’s electromagnetic specialty locks provide flexibility for a
variety of applications. They offer a depth of features and a
proven record of performance.
Electric power transfer accessories
5 1/2" butt hinges – 130˚ swing,
Electromagnetic locks consist of an armature and a coil
assembly, which become magnetized when an electric current
passes through them. This magnetic field secures the door.
Electromagnetic locks are fail-safe by design. To unlock the door
simply remove power.
Features and certifications:
M490DE: Delays egress with 15 second timer: includes
integrated alarm
§§ Designed to meet NFPA 101 & BOCA, UL 10C 3 hr fire rating, UL
294, and BHMA 1500 lb. hold force
M490G: Gate lock is weather resistant for exterior swinging and
sliding gates
§§ BHMA 1500 lb. hold force rated GF3000: Concealed locking
mechanism enhances security and appearance
§§ UL 10C 3 hr fire rating, BHMA 1500 lb. hold force 320M:
MiniLine is mortise designed for interior sliding doors
§§ UL 10C 3 hr fire rating, UL 1034 listed
40/70 Series Electromagnetic Locks
Ease of installation makes the 40/70 Series a perfect choice for
retrofit applications. It is also easy to select and stock.
Features and Certifications:
§§ Magnetic bond sensor and door status monitor standard
§§ UL 10C 1 hour fire rating and BHMA Grade 1:
- 40 Series – 500 lb. hold force
- 70 Series – 1000 lb. hold force
Von Duprin Door control and security hardware • 33
Monitor strikes
Monitor strikes are designed to offer remote door monitoring
through the use of a signal switch mounted in the strike to
monitor the latch bolt. This series of monitor strikes is designed
for use with Von Duprin and most other manufacturers’ rim,
mortise, surface and concealed vertical rod exit devices and
cylindrical, mortise and unit type locks.
Tripper
The monitor strike replaces the standard door strike. The tripper
in the monitor strike is depressed when the latch bolt is fully
inserted in the strike. The stainless steel tripper activates an
electric switch.
Features and benefits
UL listed as “miscellaneous door accessory”
11
Signal Switch
Housing
12
13
Faceplate
Note: Tripper selection is based on the
throw and shape of the latch bolt.
Monitor strike electrical rating
SPDT Switch (single pole double throw):
24VDC @ 2 Amps (resistive)
Monitor strikes
Series 4263, 4268-T1, 4582
Model specifications
Model #
4263
4268-T1
4582
Lockset
Rim or surface vertical rod
exit devices
Rim fire exit devices
Mortise or cylindrical locks
# Doors
Single or pair
Single or pair
Single or pair
Compatibility
(with tripper type)
Von Duprin 22, T3
2227, T1
33A/35A, T3
3327A/3527A, T3
44, T1
55, T1
88, T1
8827, T1
98/99, T3
9827/9927, T1
Monarch
Rim, T3
(3⁄49" [19mm] throw)
Yale®
1500, T1
(5⁄89" [16mm] throw)
Von Duprin 22/22-F
33A/35A
88/88-F
98/99
98-F/99-F
Schlage
Falcon
Arrow™
Corbin Ruswin®
Yale®
UL list (GXHX R4504)
fire exit hardware
UL List (GXHX R4504)
fire exit hardware
2
3
Certifications
Application notes
1
⁄4" (19mm) Cyl., T2
L90, T2
5
⁄8" (16mm) ML (LR), T2
5
⁄8" (16mm) ML (LR), T1
5
⁄8" (16mm) ML (LR)
5999 ML (LR), T2
5
⁄8" (16mm) ML (LR), T2
3
Application notes:
The 4263 is non-handed and features horizontal adjustment to compensate for misalignment of door and frame. 4263 may be used with a mullion. Tripper selection (-T1 or
-T3) is based upon the lock to be used with.
The 4268 features horizontal adjustment to compensate for misalignment of door and frame. 4268-T1 is not for use with mullions.
For use on single or pair of doors with ANSI 115.3 frame cutout (frame modification required.) Tripper selection (-T1 or -T2) is based upon the lock to be used.
34 Von Duprin Door control and security hardware
34•
Monitor strikes
Basic monitor strike circuit
Power supply same voltage as lamps
with sufficient current capabilities
Series 4570T1, 4670-T1, 4690-T2, 4690-1-T2
Model #
4570-T1
4670-T1
4690-T2
4690-1-T2
Lockset
Cylindrical locks
Cylindrical locks
Concealed vertical
rod exit devices
Concealed vertical
rod exit devices
# Doors
Single or pair
Single or pair
Wide stile pair
of doors
Narrow stile pair
of doors
Compatibility
(with tripper
type)
1
Schlage
⁄29" (13mm) Cyl.
5
⁄89" (14mm) Cyl
1
Falcon
⁄29" (13mm) Cyl.
9
⁄169" (14mm) Cyl.
Adams Rite®4510
8400
1
Arrow™
⁄29" (13mm) Cyl.
9
®
Best ⁄169" (14mm) Cyl.
Corbin Russwin® 5⁄89" (16mm) Cyl.
Dexter® 7⁄169" (11mm) Cyl.
1
Kwikset®
⁄29" (13mm) Cyl.
™
Precision 1040 Automatic
Flush Bolt1
1
®
Sargent ⁄29" (13mm) Cyl.
1
Yale®
⁄29" (13mm) Cyl.
1
Schlage
⁄29" (13mm) Cyl.
5
⁄89" (14mm) Cyl.
1
Falcon
⁄29" (13mm) Cyl.
9
⁄169" (14mm) Cyl.
Adams Rite®4510
8400
1
Arrow™
⁄29" (13mm) Cyl.
9
®
Best ⁄169" (14mm) Cyl.
Corbin Russwin® 5⁄89" (16mm) Cyl.
Dexter® 7⁄169" (11mm) Cyl.
1
Kwikset®
⁄29" (13mm) Cyl.
™
Precision 1040 Automatic Flush Bolt1
1
®
Sargent ⁄29" (13mm) Cyl.
1
Yale®
⁄29" (13mm) Cyl.
Von Duprin 3347A-F Von Duprin 3347A
3347A
9947
9947F
Certifications
Application notes 1
1
Monitor strikes
Model specifications
UL list (GXHX
R4504)
fire exit hardware
2
3
4
Special template required
Application notes:
For use on single or pair of doors with ANSI 115.2 frame cutout (frame modification required.) 4570-T1 is only used with T1.
For use on single or double doors with ANSI 115.3 fame cutout (frame modification required.) 4670-T1 is only used with T1.
For use with pair of doors where one leaf has concealed vertical rods. 4690-T2 is only used with T2.
For use with pair of doors where both leaves have concealed vertical rods. 4690-1-T2 is only used with T2.
35
Von Duprin Door control and security hardware • 35
Monitor strikes dimensions
4263
4670-T1
(29mm)
(41mm)
1/4"
Top
1 1/8"
1 5/8"
(6mm)
13/16"
13/16"
2 7/8"
1 5/16"
(73mm)
(21mm)
(21mm)
2 3/4"
(33mm)
1 1/8"
(70mm)
(29mm)
1"
(25mm)
7/64"
11/64"
1 1/8"
(4mm)
4268-T1
(3mm)
1 17/32"
(39mm)
(29mm)
4690-T2
1"
Top
(25mm)
Monitor strikes dimentions
1"
(25mm)
6"
(152mm)
1 5/16"
3 1/4"
(33mm)
1 5/16"
(83mm)
13/16"
1 5/8" (21mm)
(6mm)
(29mm)
(41mm)
3/32"
1/4"
1 1/8"
(33mm)
(2mm)
1 1/4"
4570–T1
1 25/32"
(45mm)
(32mm)
4690–1–T2
Top
Top
13/16"
1"
(25mm)
(21mm)
4 7/8"
1 5/16"
1 1/8"
(124mm)
(33mm)
2 7/16"
3 1/4"
(29mm)
(62mm)
(83mm)
1 5/16"
7/64"
(3mm)
(33mm)
7/64"
1 1/4" (3mm)
3/32"
(32mm)
(2mm)
1/4"
(6mm)
1 17/32"
1 25/32"
(45mm)
1 1/4"
(32mm)
(39mm)
4582
To order, specify
Top
1. Model
2. Tripper T1, T2 or T3
1 1/16"
3. Handing required on model 4582
(27mm)
4. Specify LHR or RHR
5. Finish: US3, US4, US10, US10B, US26, US26D
4 7/8"
(124mm)
Allegion, the Allegion logo, Von Duprin and the Von Duprin logo are trademarks of
Allegion plc, its subsidiaries and/or affiliates in the United States and other
countries. All other trademarks are the property of their respective owners.
1 5/16"
(33mm)
1/4"
(6mm)
3/32"
(2mm)
36 Von Duprin Door control and security hardware
36•
1 25/32"
(45mm)
Mullions
Electrified removable mullions are used with pairs of doors
eq.uipped with rim mounted exit devices.
Each includes an electric cable with five conductors wired to a
twist-apart plug. The soffit fitting is supplied with a pre-wired
mating socket.
4754 — Prepared for two 4263 monitor strikes. Use with all Von
Duprin rim panic devices.
Steel mullion
dimensions
4854 — Prepared for one 6111 electric strike and one 299 strike.
Indicate handing for electric strike.
2"
9854 — Prepared for one 6111 electric strike and one 268 or 499F
strike. Indicate handing for electric strike. UL Fire labeled for up
to 3 hours on up to 8' x 8' (2438mm x 2438mm) openings using
Von Duprin fire exit rim devices.
3"
Wall Thickness 1/8" (3mm)
Sizes for mullions
4754, 4854, 9854
7' 2" (2184mm)
*10' 2" (3099mm)
KR4754, KR4854
KR9854**
8' 6" (2591mm)
*8' 5" (2565mm)
10' 6" (3200mm)
*10' 5" (3175mm)
7' 6" (2286mm)
KR - Keyed removable option available on electrified removable
mullion. Makes removal faster and easier by a single operation of
the mortise cylinder. Once mullion is removed, large equipment
or furniture can freely pass through the opening. The unit will self
lock when re-installed, without use of the cylinder key. Uses
1 1/4" mortise cylinder with a straight cam (Schlage cam reference
B502-191). Cylinders are sold separately. Prefix mullion model
with “KR”.
7' 5" (2261mm)
Mullions
*8' 2" (2489mm)
* Only qualifying applications will be provided with UL Label.
** Fire rated same as 9854
Quick disconnect
To order, specify
1. Model number.
2. Height of opening
3. Finish: SP28, SP313, SPBLK.
4. Handing if required.
5. C
enterline deviation (refer to device
template for standard centerline).
6. S
trikes, when required, should be ordered with device.
7. F
or keyed removable option prefix model number with
“KR”, example KR9854.
Soffit details
1" (25mm) Diameter
Clearance
Reinforcement
Filler block is to be
supplied by the frame
mgf. for conditions
similar to this.
37
Von Duprin Door control and security hardware • 37
Notes
38• Von Duprin Door control and security hardware
Notes
Von Duprin Door control and security hardware • 39
About Allegion
Allegion (NYSE: ALLE) creates peace of mind by pioneering safety and security.
As a $2 billion provider of security solutions for homes and businesses, Allegion
employs more than 8,000 people and sells products in more than 120 countries
across the world. Allegion comprises more than 25 global brands, including
strategic brands CISA®, Interflex®, LCN®, Schlage® and Von Duprin®.
For more, visit www.allegion.com
© 2013 Allegion
009981, Rev. 11/14
www.allegion.com/us