Cisco PVC2300 - Small Business Internet Video Camera User guide

USER GUIDE
BUSINESS SERIES
Business Internet
Camera with Audio
Model: PVC2300, WVC2300
About This Guide
About This Guide
Icon Descriptions
While reading through the User Guide you may encounter
various icons designed to call attention to a specific item.
Below is a description of these icons:
Open Source
This product may contain material licensed to you under
the GNU General Public License or other open-source
software licenses. Upon request, open-source software
source code is available at cost from Linksys for at least
three years from the product purchase date.
WEB: For detailed license terms and additional
information visit: www.linksys.com/gpl
NOTE: This check mark indicates that there is
a note of interest and is something that you
should pay special attention to while using the
product.
WARNING: This exclamation point indicates
that there is a caution or warning and it is
something that could damage your property or
product.
WEB: This globe icon indicates a noteworthy
website address or e-mail address.
Online Resources
Website addresses in this document are listed without
http:// in front of the address because most current web
browsers do not require it. If you use an older web browser,
you may have to add http:// in front of the web address.
Resource
Website
Linksys
www.linksys.com
Linksys International
www.linksys.com/international
Glossary
www.linksys.com/glossary
Network Security
www.linksys.com/security
Copyright and Trademarks
Specifications are subject to change without notice.
Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain
other countries. Copyright © 2007 Cisco Systems, Inc. All
rights reserved. Other brands and product names are
trademarks or registered trademarks of their respective
holders.
Business Internet Video Camera with Audio
Table of Contents
Chapter 1: Introduction
1
Minimum Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Chapter 2: Wireless Security Checklist
2
General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 3: Product Overview
3
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 4: Installation 5
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Linksys Wired Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Linksys Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Linksys One Ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Linksys One Wired Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Linksys One Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting Up the Wireless Connection on the WVC2300 Camera . . . . . . . . . . . . . . . . . . 9
Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 5: Installing and Using the Viewer and Recorder Software
12
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the Monitor Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Video Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting Up Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Recording Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Using the Playback Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Video Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Chapter 6: Advanced Configuration
18
Home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Business Internet Video Camera with Audio
ii
Table of Contents
Setup > Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
HTTP/HTTPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
RTP/RTSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Bonjour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
CoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setup > IP Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Administration > Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
User List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Administration > Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Restore Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Administration > Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Audio/Video > Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
MPEG-4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
MJPEG Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Mobile Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Video Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Day/Night Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Audio/Video > Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Applications > Mail & FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Applications > Instant Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Jabber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Applications > Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Applications > Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Event Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
New Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Trigger Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Event Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Applications > DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Applications > I/O Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Input Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Output Ports State at Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Business Internet Video Camera with Audio
iii
Table of Contents
Output Ports Manual Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Applications > RS-485 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Preset Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Patrol Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Status > System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Status > Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
MPEG-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
MJPEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Status > Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Status > Syslog & Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Syslog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Log List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Status > Video Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Video Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Appendix A: Troubleshooting
34
Appendix B: Bandwidth Usage
35
WVC2300 Bandwidth Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Appendix C: Glossary
36
Appendix D: Specifications
40
PVC2300 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
WVC2300 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
I/O Port Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Appendix E: Warranty Information
45
Appendix F: Wired Product Regulatory Information
46
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Avis d’Industrie Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Appendix G: Wireless Product Regulatory Information
51
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Business Internet Video Camera with Audio
iv
Table of Contents
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Industry Canada Radiation Exposure Statement: . . . . . . . . . . . . . . . . . . . . . . 51
Avis d’Industrie Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Avis d’Industrie Canada concernant l’exposition aux radiofréquences : . . . . . . . . 52
Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Avis de non-responsabilité concernant les appareils sans fil . . . . . . . . . . . . . . . . . . 52
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Appendix H: Contact Information
Business Internet Video Camera with Audio
57
Introduction
Chapter 1
Chapter 1:
Introduction
With extensive feature support like IP Multicast, RTSP, RTP,
and 3GPP, video can be viewed from multiple endpoints
and client applications like 3G phones, and Quicktime
clients on PCs or Wi-Fi phones.
Thank you for choosing the Linksys Business Internet Video
Camera with Audio. This User Guide covers two models:
Support for multiple network protocols like 802.1p priority,
802.1q VLANs, and Dynamic DNS, make the solution ideal
for multiple IP surveillance applications. The Cameras can
also be managed securely using HTTPS.
•
PVC2300 Business Internet Video Camera with Audio
and PoE (Power over Ethernet)
•
WVC2300 Wireless-G Business Internet Video Camera
with Audio
NOTE: For the purpose of this User Guide,
whenever a feature applies to both models, the
word Camera(s) will be referenced. If a specific
model number is mentioned, then the feature
is specific to that model.
Linksys Business Series Surveillance Cameras are also
Linksys One Ready. That means they include the necessary
firmware to be integrated into a Linksys One data or data/
voice network.
Minimum Requirements
Minimum System Requirements (for 1 camera):
CPU
Pentium 4 class, 2 GHz
Memory
512 MB
Operating System
Microsoft Windows 2000, XP or Vista
Hard Drive
500 MB of available space
Graphics Card
AGP with a minimum 128 MB
The Cameras can be mounted on any PT base that
supports Pelco_D protocol and can be remotely rotated
and controlled through an RS-485 interface. The Camera
supports 2 input and 2 output connectors which can be
used for connecting to an alarm panel, siren, PIR, smoke
detectors, light switch (on/off ), door opener, etc.
Browser
Internet Explorer 6.0 (or above), Mozilla
Firefox, and Netscape 7.0 (or above)
The Cameras incorporate a high quality progressive scan
CCD sensor, delivering good quality undistorted video.
The sensor used in the Cameras has Low light sensitivity
capability. This means that video can be viewed when
very low light (near darkness) is present. Additionally, the
Cameras incorporate an IR Cut Filter switcher which, when
used with a separate IR lamp, allows for viewing of video
in total darkness.
CPU
Pentium 4 class, 3 GHz dual-core
Memory
1 GB
The new Linksys Surveillance solutions are high quality
solutions which can be optimized for many different
applications. The box-type form factor allows these
cameras to be used as-is or put inside an outdoor enclosure
for interior or exterior applications. The cameras use
removable CS-mount lenses and can be customized with
Zoom, Wide-Angled, Vari-focal, Auto-Iris, or other type of
lenses as required for the specific application.
The PVC2300 provides Power over Ethernet (PoE)
functionality that facilitates installation of the PVC2300 in
places without reach of a power outlet.
The Cameras support dual CODECs - MPEG-4 and MJPEG.
Both CODECs can be used simultaneously. MPEG-4 gives
efficient bandwidth consumption with good quality
compression and is optimal for real-time viewing of video.
MJPEG gives optimal video quality in lossy environments
making it ideal for video storage to a NAS device.
The Camera’s audio capabilities include 2-way audio, an
embedded microphone, external speaker and microphone
ports, and voice compression.
Business Internet Video Camera with Audio
Minimum System Requirements
(for up to 8 cameras):
Operating System Microsoft Windows 2000, XP or Vista
Hard Drive
4 GB of available space
Graphics Card
NVidia high performance or equivalent
with a minimum 256 MB
Browser
Internet Explorer 6.0 (or above), Mozilla
Firefox, and Netscape7.0 (or above)
NOTE: For 9 cameras or more, reduce the
resolution and frame rate settings and the same
minimum requirements apply as listed above.
Wireless Security Checklist
Chapter 2
Chapter 2:
Wireless Security Checklist
Wireless networks are convenient and easy to install, so
businesses with high-speed Internet access are adopting
them at a rapid pace. Because wireless networking operates
by sending information over radio waves, it can be more
vulnerable to intruders than a traditional wired network.
Like signals from your cellular or cordless phones, signals
from your wireless network can also be intercepted. Since
you cannot physically prevent someone from connecting
to your wireless network, you need to take some additional
steps to keep your network secure.
1. Change the default wireless network name or SSID
Wireless devices have a default wireless network name
or Service Set Identifier (SSID) set by the factory. This
is the name of your wireless network, and can be up
to 32 characters in length. Linksys wireless products
use linksys as the default wireless network name. You
should change the wireless network name to something
unique to distinguish your wireless network from other
wireless networks that may exist around you, but do not
use personal information (such as your Social Security
number) because this information may be available for
anyone to see when browsing for wireless networks.
2. Change the default password
For wireless products such as access points and routers,
you will be asked for a password when you want to change
their settings. These devices have a default password set
by the factory. The Linksys default password is admin.
Hackers know these defaults and may try to use them
to access your wireless device and change your network
settings. To thwart any unauthorized changes, customize
the device’s password so it will be hard to guess.
4. Enable encryption
Encryption protects data transmitted over a wireless
network. Wi-Fi Protected Access (WPA/WPA2) and Wired
Equivalency Privacy (WEP) offer different levels of security
for wireless communication. Currently, devices that are
Wi-Fi certified are required to support WPA2, but are not
required to support WEP.
A network encrypted with WPA/WPA2 is more secure
than a network encrypted with WEP, because WPA/WPA2
uses dynamic key encryption. To protect the information
as it passes over the airwaves, you should enable the
highest level of encryption supported by your network
equipment.
WEP is an older encryption standard and may be the
only option available on some older devices that do not
support WPA.
General Network Security Guidelines
Wireless network security is useless if the underlying
network is not secure.
•
Password protect all computers on the network and
individually password protect sensitive files.
•
Change passwords on a regular basis.
•
Disable file sharing (peer-to-peer). Some applications
may open file sharing without your consent and/or
knowledge.
Additional Security Tips
•
Keep wireless routers, access points, or gateways away
from exterior walls and windows.
•
Turn wireless routers, access points, or gateways
off when they are not being used (at night, during
vacations).
•
Use strong passphrases that are at least eight characters
in length. Combine letters and numbers to avoid using
standard words that can be found in the dictionary.
3. Enable MAC address filtering
Linksys routers give you the ability to enable Media Access
Control (MAC) address filtering. The MAC address is a
unique series of numbers and letters assigned to every
networking device. With MAC address filtering enabled,
wireless network access is provided solely for wireless
devices with specific MAC addresses. For example, you can
specify the MAC address of each computer in your home
so that only those computers can access your wireless
network.
Business Internet Video Camera with Audio
Product Overview
Chapter 3
Chapter 3:
Product Overview
Back Panel
The ports and reset button are located on the back panel
of the Camera.
Front Panel
The LEDs and Camera lens are located on the front panel
of the Camera.
Back Panel - PVC2300
Front Panel
Lens The Camera includes a removable
CS‑mount lens. For specifications on the
included lens, refer to the Specifications section
of this User Guide. For a list of recommended
lenses to use with this Camera, please refer to
the Quick Installation Guide.
Built-in microphone There is a built-in
microphone mounted on the front of the
Camera. The Camera also has a connection for
an external microphone on the rear. Connecting
an external microphone will disable the built-in
microphone.
Ready LED (Amber) The Ready LED has the
following states:
•
Off Camera is powered off.
•
On Camera is powered on.
•
Flashing The Ready LED will flash during
start up. This will take 15 to 20 seconds.
Network LED (Green) The Network LED has
the following states:
•
Off Network connection not detected.
•
On Network connection detected.
•
Flashing Sending/receiving data.
Business Internet Video Camera with Audio
Back Panel - WVC2300
Antenna Connectors Antenna connectors
are only found on the WVC2300 Camera. The
connectors are used to attach the antennas to
the device for wireless connectivity.
Reset The reset button can be accessed with
a straightened paper clip or similar object. The
reset button has two functions:
•
Restore Factory Defaults To restore the
factory default settings, press the Reset
button for more than 10 seconds. When you
let go of the button, the LEDs on the front
of the Camera will flash and then return to a
normal state when the Camera is ready.
•
Set Static IP Address By default the
camera is set to receive an IP address from
a DHCP server. If you do not have a DHCP
server on your network, you can set a static
IP address by pressing the Reset button
on the camera for less than 10 seconds. A
default IP address of 192.168.1.99 will be
assigned to the camera.
Product Overview
Chapter 3
Ethernet The Ethernet port supports network
speeds of either 10 Mbps or 100 Mbps, and can
operate in half and full-duplex mode.
PVC2300 PoE LED This LED only functions on
the PVC2300 Camera. The LED has the following
states:
Auto-sensing technology enables the port to
automatically detect the speed of the device
connected to it (10 Mbps or 100 Mbps), and
adjust its speed and duplex accordingly.
On PoE connection is detected.
The Ethernet port supports automatic MDI/
MDI-X operation, so you can use straightthrough or crossover cables to connect to PCs,
servers, or switches.
NOTE FOR PVC2300 USERS: The
PVC2300 Camera’s Ethernet port also
supports the IEEE 802.3af Power-overEthernet (PoE) standard that enables
DC power to be supplied to the
Camera using wires in the connecting
twisted-pair cable. Any 802.3afcompliant device attached to the
port can directly supply power to the
Camera over the twisted-pair cable
without requiring its own separate
power source. This capability gives
network administrators centralized
power control, which translates into
greater network availability.
To connect a device to the port, you will need
to use Category 5 (or better) network cable.
NOTE FOR WVC2300 USERS:
Attaching an Ethernet cable will
disable the wireless interface on the
WVC2300 Camera. Only one interface
can be active at any time.
NOTE FOR WVC2300 USERS: On
the WVC2300 Camera, the Ethernet
cable should only be connected or
disconnected when the Camera is
powered OFF. Attaching or detaching
the Ethernet cable while the Camera
is powered on does NOT switch
the interface between wired and
wireless.
Off PoE connection is not detected.
Power The Power port is where you will
connect the power adapter.
NOTE FOR PVC2300 USERS: The
Power port is automatically turned of
if a PoE connection is detected on the
Ethernet port.
GPIO This port is utilized for I/O connections.
Detailed specifications can be found in the
Specifications section of this User Guide.
10
9
8
7
6
5
4
3
2
1
Mic In This jack is used to connect an external
microphone to the camera.
Spkr Out This jack is used to connect powered
speakers to the Camera.
Side Panel
The security slot is located on a side panel of the Camera.
Side Panel
SECURITY SLOT The security slot can be
utilized to attach a lock to the Camera.
Activity LED The Activity LED flashes when
activity is detected on the Ethernet port.
Business Internet Video Camera with Audio
Installation
Chapter 4
Chapter 4:
Installation
Overview
This chapter will explain how to install the Camera into a
wired or wireless network. The following diagrams show
some typical network configurations.
Linksys Wired Network
Linksys One Ready
When the Camera is connected to a Linksys One network,
you can access the images using the Linksys One Video
Surveillance Application (VSA) from any PHM1200 IP
phone or web browser. The Linksys One VSA is a zero
configuration plug-and-play application. The Camera
sends live video feeds at a rate of 2 fps (frames per second)
to your phone or web browser, with the option to receive
alerts for motion detection and other events. You can easily
configure the system to store video captures, send event
notifications via e-mail, and operate with devices such as
alarm systems, solenoid locks, and lighting controls.
The Linksys One VSA works in conjunction with the
following Linksys and Linksys One devices:
Example Linksys Wired Network
Linksys Wireless Network
•
Linksys One Application Server Appliance, model
APP1000 (Required)
•
Linksys One Ready Business Internet Video Camera
with Audio, model PVC2300 or WVC2300 (Required)
•
Linksys One Services Router, model SVR200 required if
a WVC2300 camera is installed (Required)
•
Linksys One IP Phone, PHM1200 (Optional)
•
Linksys One Ready Switches, any model (Optional)
•
Linksys One Ready Network Attached Storage Device,
any model, or FTP server for the storage of video files
(Optional)
End-user documentation, including the Linksys One Video
Surveillance Application User Guide (v2.1 or above) is
available on the web at www.linksysone.com
Linksys One Wired Network
Example Linksys One Wired Network
Example Linksys Wireless Network
Business Internet Video Camera with Audio
Installation
Chapter 4
Linksys One Wireless Network
2. Connect the camera stand to the bottom of the
camera. Adjust the camera to the appropriate viewing
position.
Locknut
Once the camera is positioned properly, secure the
camera in place by tightening the locknut.
3. Connect the included Ethernet network cable to your
network router or switch.
Example Linksys One Wireless Network
LINK/ACT
PoE
LINK/ACT
PoE
LINK/ACT
Gigabit
LINK/ACT
Gigabit
Hardware Installation
NOTE: Before attaching the camera extension or
swivel head, the stand base can be mounted in
a permanent location by using three screws to
secure the stand base to the desired location.
1. The Camera stand can be connected two different
ways:
•
Attach the stand base to the camera extension and
attach the camera extension to the swivel head.
Camera Extension
Stand Base
•
4. Connect the other end of the cable to the Camera’s
Ethernet port.
LEDs
Link
PoE
Locknut
Swivel Head
You can connect the swivel head directly to the stand
base if the extension isn’t necessary.
Swivel Head
Stand Base
Business Internet Video Camera with Audio
If your network switch provides Power over Ethernet
to the Camera, verify the Camera’s LEDs are lit and skip
steps 5-7.
5. Connect the included power adapter to the Camera’s
Power port and plug the other end into a standard
electrical outlet.
Installation
Chapter 4
Configuration
1. Insert the Setup CD into your CD‑ROM drive. If the CD
doesn’t run automatically, go to My Computer and
click on your CD-ROM drive.
Verify that the Camera’s LEDs are lit.
2. The Setup screen will appear. Click the Click Here to
Start button.
LED Table
LED
Color
Ready
Amber
Network Green
Activity Action
Off
Camera is powered off
On
Camera is powered on
Blink
Camera is booting
Off
Network connection not
detected
On
Network connection
detected
Blink
Sending/receiving data
3. The license agreement screen will appear, click Next if
you agree and wish to proceed.
NOTE: Hardware Installation steps 6 and 7 are
only necessary if you are using the WVC2300
Wireless-G Business Internet Video Camera.
6. Connect the antennas to the antenna connectors on
the Camera.
4. The Wizard will now search for your camera.
7. Place the antennas in an upright position.
Business Internet Video Camera with Audio
Once found highlight the camera and click Next.
Installation
Chapter 4
If the Camera you want is not displayed in the Selection
box, click Search Again.
NOTE: The Camera defaults to DHCP mode. If
your network doesn’t have a DHCP server or if
you are having issues obtaining an IP address,
you can assign a static IP address to the Camera
by pressing the reset button for less than 10
seconds. A static IP address of 192.168.1.99
will be assigned to the Camera.
Reset Button
–
Camera Name Enter a unique name for the
Camera, up to 15 characters in length. Unique
names are helpful when you are using multiple
Cameras on the same network.
–
Description Enter a description, up to 32
characters in length, with additional information,
such as the location of the Camera.
–
Time Zone Select the time zone that corresponds
with the Camera’s location.
–
Date Enter the current date in the provided fields.
–
Time Enter the current time in the provided fields.
When you have finished making changes, click
Next.
7. If you want to assign the IP address, then select Static
IP address, otherwise leave the default setting,
Automatic Configuration DHCP.
WARNING: Pressing the reset button for more
than 10 seconds will restore all of the factory
default settings, including setting the Camera
to DHCP mode.
5. The default user name and password is admin. Type
admin in lowercase letters, in the Administrator Name
and Administrator Password fields, then click OK.
8. The New Internet Camera Settings screen will appear
and display the Camera’s settings. Click Next to
continue or click Back to make changes.
For security purposes, it is recommended that you
change the default name and password using the
Camera’s web-based utility at a later time.
6. On the Basic Settings screen, change the following
settings:
Business Internet Video Camera with Audio
9. A confirmation window will appear, click OK to confirm
the settings.
Installation
Chapter 4
14. Click the Install button.
A timer will appear as the settings are saved to the
Camera.
10. A window will appear indicating that the settings have
been saved successfully. Click OK to continue.
You should be able to view video on the home page.
11. The Wizard will now return to the Welcome screen. Click
Exit to automatically launch your default web browser
and proceed to the Home page login screen.
Setting Up the Wireless Connection on the
WVC2300 Camera
12. The login prompt will appear, enter admin in both the
User name and Password fields.
To configure the Camera for wireless connectivity, you
must still be connected to the home page.
1. Click on Setup to open the Setup > Basic Setup screen.
2. Enter the appropriate Wireless Settings:
SSID The SSID is the network name shared among all
devices in a wireless network. Enter the network’s SSID or
network name here. The SSID is case sensitive.
Network Type Select the appropriate network mode:
13. Internet Explorer will prompt you to install ActiveX.
In order to view video you must accept the ActiveX
download.
•
Infrastructure Use this option if you are connecting
the Camera to an access point or router.
•
Ad-hoc Use this option if you are connecting the
Camera directly to a PC or notebook.
Channel No If the Camera is set to ad-hoc mode, select
its channel setting from the drop-down menu.
NOTE: When using Infrastructure mode, the
channel setting is configured automatically.
Click Install ActiveX Control.
Business Internet Video Camera with Audio
Security Click the Edit Security Settings button to
display the Wireless Security screen.
Installation
Chapter 4
Wireless Security
WPA /WPA2 Enterprise
Security Mode Select the appropriate option based on
your wireless network configuration:
The screen options vary depending upon the protocol
type selected.
•
Disabled This option implements no security on
your wireless network. Data is not encrypted before
transmission.
•
WEP WEP is a basic encryption method, which is not
as secure as later methods such as WPA-Personal or
WPA2 Personal. However, it is supported by all clients.
•
WPA /WPA2 Personal This method offers two
encryption methods, TKIP and AES, with dynamic
encryption keys.
•
WPA /WPA2 Enterprise This option requires that
your LAN has a RADIUS server for authentication.
WEP
Protocol Type Select EAP-TLS or EAP-TTLS.
EAP-TLS
Wireless Security > Security Mode > WPA /WPA2 Enterprise (EAP-TLS)
•
User ID The user ID used to login to your RADIUS
server.
•
Root CA A root certificate is an unsigned public key
certificate, or a self-signed certificate, which implies
that you trust your browser’s publisher to include
correct root certificates, and in turn the certificate
authorities it trusts, and anyone to whom the CA may
have issued a certificate-issuing-certificate, to faithfully
authenticate the users of all their certificates.
•
User CA A user certificate is a signed private key
certificate, which implies that you trust your browser’s
publisher to include correct user certificates, and in
turn the certificate authorities it trusts, and only user
to whom the CA may have issued a certificate-issuingcertificate, to faithfully authenticate the users of all
their certificates.
•
Password This is for this Camera’s client login to the
RADIUS server, and must match the key stored on the
RADIUS server.
Wireless Security > Security Mode > WEP
TX Key Select the number of the key used on the wireless
network.
WEP Encryption Select the appropriate option for key
length based on your network settings.
Passphrase Type in the passphrase used to generate WEP
keys on your network and click the Generate button.
Key 1-4 Key values can be entered in manually or
generated from a passphrase.
EAP-TTLS
Authentication Select the appropriate authentication
type used on the wireless network.
WPA /WPA2 Personal
Wireless Security > Security Mode > WPA /WPA2 Enterprise (EAP-TTLS)
Wireless Security > Security Mode > WPA /WPA2 Personal
•
Process Method Choose an authentication method
as required to handle the processing and transmitting
of CA to your RADIUS server.
•
User ID The user ID used for login to your RADIUS
server.
Encryption This cannot be modified.
Shared Key Enter the shared key used for accessing the
wireless network.
Business Internet Video Camera with Audio
10
Chapter 4
•
Password This is for this Camera’s client login to the
RADIUS server.
•
Anonymous ID The unsigned public ID used for login
to your RADIUS server.
•
Root CA A root certificate is an unsigned public key
certificate, or a self-signed certificate, which implies
that you trust your browser’s publisher to include
correct root certificates, and in turn the certificate
authorities it trusts, and anyone to whom the CA may
have issued a certificate-issuing-certificate, to faithfully
authenticate the users of all their certificates.
Installation
6. Disconnect the Ethernet Cable from the Camera.
3. Click Save to save the wireless security settings and
close out the window manually.
4. On the Setup > Basic Setup screen, click the Save button
to save the wireless settings.
5. Disconnect the power to the Camera.
NOTE: The wireless connection will not work
if an Ethernet cable is attached to the Camera
when it is powered on.
7. Reconnect the power to the Camera.
8. Click on Home in the web-based utility to verify the
video is streaming from your wireless connection. You
should be able to view video on the home page.
Business Internet Video Camera with Audio
11
Chapter 5
Installing and Using the Viewer and Recorder Software
Chapter 5:
Installing and Using the
Viewer and Recorder
Software
3. The Choose Destination Location screen will appear. To
install the Viewer & Recorder Utility files in the default
folder, click the Next button. To select a different folder,
click the Browse button and follow the on‑screen
directions.
Overview
This chapter will instruct you on how to install and use the
Internet Camera Viewer & Recorder Utility on your PC. The
Utility allows you to easily view and record video.
If another Internet Camera Viewer & Recorder Utility has
already been installed on your PC, you should uninstall it
before installing this software.
Installing the Software
1. On the Welcome screen of the Setup Wizard, click
Install Viewer & Recorder Utility.
Choose Destination Location
4. The Ready to Install screen will appear. The selected
destination path will be displayed. If you wish to change
the path, click the Back button. If you are satisfied with
the location, click the Next button to continue.
Ready to Install
Setup Wizard Welcome Screen
5. Click Finish to complete the installation.
2. The Welcome screen will appear. Click the Next button
to proceed.
Welcome Screen
Business Internet Video Camera with Audio
12
Chapter 5
Installing and Using the Viewer and Recorder Software
Using the Monitor Application
Viewing When a Camera has a green
light under this icon, it indicates the
video is being viewed.
After the software has been installed, you can launch the
application from shortcuts on the desktop and in the Start
menu.
Recording When a Camera has a red
light under this icon, it indicates that
video is being recorded.
Motion When a Camera has a light
under this icon, it indicates that motion
has been detected.
Input 1 This indicates that input 1 has
been triggered.
Desktop Shortcuts
Input 2 This indicates that input 2 has
been triggered.
Once you’ve launched the Monitor application, you will
see the Monitor’s main screen. From this screen, you can
configure and control Cameras.
Camera Number This indicates which
Camera number the indicators apply to.
Alert Log List
Alert Log List Displays any alert messages.
Hard Disk Quota
Free Space Displays the amount of free space available at
the recording path defined in the preferences. By default
this is your local drive.
Used Space Displays the amount of space used by video
clips captured using the utility.
Setup Clicking this button opens the
Camera Setup window.
Monitor Main Screen
Video Monitor
The following list details the function of the icons found
on the Video Monitor screen.
Camera Indicators
The Video Monitor includes a camera indicator window.
The icons indicate the activities associated that are active
for the Cameras.
Playback Clicking this button opens
the Video Playback window.
Play Use this button to re-start viewing,
after using the Stop or Pause button.
Pause Clicking this pauses the video
stream.
Stop This terminates the connection
to the camera, halting viewing and
recording (if in progress). If stop is
pressed while recording, the first click
stops recording. The second click stops
video streaming.
Record Clicking this button begins
recording a video stream. While
recording, this button will be blue. To
stop recording, click the Stop button.
Business Internet Video Camera with Audio
13
Chapter 5
Installing and Using the Viewer and Recorder Software
Snapshot Clicking this captures an
image from the current video.
Zoom Clicking this magnifies a section
of the window. Click the icon and then
click the portion of the screen you want
to magnify. Click the icon again to return
magnification to normal.
Several setup options appear on the left-hand side of the
screen. They are Camera Setup, Recording Schedule, and
Preferences. Each of these options are described in the
following:
Camera Setup
Flip Video Click this to have the image
swapped top-to-bottom.
Mirror Video Click this to have the
image swapped left-to-right.
Sound On/Off Toggles the sound on or
off.
Microphone Off Click this icon to turn
the microphone on.
Microphone On This icon will appear
when the microphone is on. The volume
slider below will appear. Click this icon
to turn the microphone off.
Volume When audio is available,
raising or lowering this bar will change
the volume.
Monitor > Setup > Camera Setup
Adding a Camera
To configure a camera for display on the main screen,
follow the directions below:
1. Select the appropriate Camera No. to configure.
Port 1
Port 1 Off/On Allows you to manually
turn off or on the output for port 1.
2. Click LAN or Internet, depending upon how you are
accessing the Camera.
3. Enter the Camera’s data into the Camera Data fields:
•
Local ID Enter a name for the camera (this name will
be the folder name for recorded video files).
•
IP Address Enter the camera’s IP address here.
•
Port Number Enter the port number assigned to this
camera. The port number is configured on the Setup >
Advanced Setup screen in the web‑based utility.
•
User (Name) Enter a valid user name configured in the
Camera’s web-based utility (Administration > Users).
•
Password Enter the password associated with the
user name that was defined in the web-based utility.
•
Stream Type Select the desired video stream type
Setting Up Cameras
•
The Camera’s setup functions are performed by clicking
the Setup button on the Video Monitor screen. This will
open the Setup screen.
Enable Motion Detection Select this option if you
wish to enable it.
4. Click Add and the Camera will be added to the list of
cameras if it has been properly configured.
Port 2
Port 2 Off/On Allows you to manually
turn off or on the output for port 2.
Screen Layout Select the number of Channels (Cameras)
to be displayed on screen.
Monitor > Screen Layout
5. Repeat steps 1-3 to add additional Cameras.
Business Internet Video Camera with Audio
14
Chapter 5
Installing and Using the Viewer and Recorder Software
6. Click Exit to return to the Video Monitor screen.
Deleting a Camera
You can delete any of the sixteen cameras displayed from
the Setup screen by doing the following:
2. Click the line you wish to assign to the schedule in the
box at the top of the screen.
3. Click the Add button to schedule the recording.
Deleting a Schedule
1. Select the camera you want to delete from the list in
the box at the top of the screen.
You can delete any of the sixteen schedules displayed on
this screen by doing the following:
2. Click the Delete button.
1. Select the camera you want to delete from the list in
the box at the top of the screen.
Recording Schedule
2. Click the Delete button.
Schedule a Recording
3. Click the Exit button to close the Setup screen.
You can record video while watching, or schedule
recordings to occur when you are absent. Recordings are
stored on the hard drive of the computer running the
Monitor application. Recordings can be played using the
Playback utility.
Preferences
Monitor > Setup > Preferences
Refer to the following when changing preferences.
Monitor > Setup > Recording Schedule
To set the Recording Preferences:
1. Enter the recording schedule’s data into the drop‑down
fields on this screen:
•
Local ID Select the Local ID of the Camera that you
want to schedule for recording.
•
Interval Select when or how often you want this
recording to occur.
•
Start Date From the calendar that appears when you
click the drop-down menu, select the date when this
schedule will begin.
•
Start Time Enter the time when this schedule will
begin.
•
Duration Enter the amount of time before this
schedule expires.
Business Internet Video Camera with Audio
Recording Path
Recording This is the Drive and Folder on your PC where
recorded files will be saved. The default location is C:\
Program Files\LinksysOne\LinksysOne Surveillance
Utility\Storage\Local ID\File Type. You can also click the
Browse button to select the desired drive and folder.
Instant Recording Time Limit
Maximum time limit for Instant Recording This sets
the maximum size of a recording. (Recordings are started
by clicking the Record button on the Main screen.)
Motion Detection
Record before Motion Detected Set the time so the
Utility will start recording a certain time before the Utility
detects motion in a Camera’s field of view.
15
Chapter 5
Installing and Using the Viewer and Recorder Software
Record after Motion Detected Set the time so the Utility
will stop recording a certain time after the Utility detects
motion in a Camera’s field of view.
Disk Allocation for Recording
Total Disk Space This shows the total amount of storage
space on your hard drive.
Available Disk Space This shows the amount of storage
space available on your hard drive.
Enable Disk Space Limitation This feature allows you
to limit the amount of space your recordings occupy on
your hard drive. Click the box for this feature and then
enter the Maximum Allowed Space in the next box. The
Maximum Allowed Space is the amount of space on your
hard drive you’ll allow your recordings to take up, which
should be smaller than the available room you have left
on your drive along with space for your operating system
and other programs. Plan for when that space gets full by
clicking either Overwrite Earliest File, which will delete old
recordings as new ones fill the space, or Stop Recording,
which will end your recording once you fill the space.
Allow a minimum of 300 MB storage space per camera. If
you will be using the same drive that Windows is installed
on to store your recordings, make sure you leave at least
ten percent of available disk space free.
Initial Settings
Launch this Utility when Windows Started Check this
to have this utility start when Windows starts.
Using the Playback Application
Select Camera Select the appropriate camera as defined
within the Monitor.
Recording Methods There are four recording methods
to choose from:
•
All Records Displays all records for the selected
Camera.
•
Select Period Selecting this option will narrow down
the video selections to the range defined within the
start/end date/time fields.
–
Start Date Select a starting date from the
calendar.
–
Start Time Select a starting time using the 24 hr
time format.
–
End Date Select an ending date from the
calendar.
–
End Time Select an ending time using the 24 hr
time format.
•
Event Trigger Selecting this option will limit the
video selections to videos that were recorded because
an event occurred.
•
Input Trigger Selecting this option will limit the video
selections to videos that were recorded because they
were triggered by an input.
Submit Once all of the video search parameters have
been defined, click this button to obtain your results.
Video Controls
Play Use this to re-start viewing, after
using the Stop or Pause button.
Pause Clicking this pauses the video
playback.
Frame by Frame This button is used to
play the video one frame at a time.
Stop This will terminate the connection
to the camera, halting both the viewing
and the recording (if in progress).
Snapshot Clicking this captures an image
from the current video.
Playback
Video Playback
Zoom In This button is used to zoom in
on the image.
Load Other Cameras This option allows you to point to a
specific folder to locate video from other cameras.
Business Internet Video Camera with Audio
16
Chapter 5
Installing and Using the Viewer and Recorder Software
Zoom Out This button is used to zoom
out the view.
Print This button is used to print the
image.
Playback Speed This slide bar allows you
to adjust the speed of the video playback.
Audio Controls This slide bar allows you
to control the volume level.
Sound On/Off Toggles the sound on or
off.
Hard Disk Quota
Free Space Displays the amount of available space on
the hard disk.
Used Space Displays the total amount of space used on
the hard disk.
Setup Clicking this button opens the Camera Setup
window.
Monitor Clicking this button opens the Monitor window.
Convert to AVI Click this button to convert video to the
AVI format. AVI files can be played in Windows Media
Player.
Delete Video This button allows you to delete unwanted
video.
Business Internet Video Camera with Audio
17
Advanced Configuration
Chapter 6
Chapter 6:
Advanced Configuration
Home
The Home screen is where live video can be viewed and
the output can be updated.
NOTE: By default the camera is set to receive
an IP address from a DHCP server. If you do not
have a DHCP server on your network, you can
set a static IP address by pressing the Reset
button on the camera for less than 10 seconds.
A default IP address of 192.168.1.99 will be
assigned to the camera.
Open your web browser and enter the assigned IP address
in Address field in the following format:
Setup > Summary
Address Bar
Press the Enter key and the Login screen will appear.
Output
The first time you open the web‑based utility, enter
admin (the default user name) in the User name field and
leave the password blank. Click the OK button. You can
set a password later from the Admin tab’s User Accounts
screen.
1 The output can be turned on or off.
2 The output can be turned on or off.
Resolution Select the desired resolution or the default
setting of AUTO to let the camera determine the
resolution. On This icon will turn on the selected output.
Off This icon turns off the selected output.
Login
Home
The Home screen is the first screen that is displayed. Below
the Home icon there is a Setup folder icon. Clicking on the
Setup icon expands the configuration options. There are
6 main headings: Setup, Administration, Audio/Video,
Applications, Status, and View Video Log. Each tab
contains screens that will help you configure and manage
the Camera.
Day This icon uses the standard filter for day
output.
Night This icon uses a filter for night vision.
Zoom This icon allows you to zoom in on a
selected area. The camera allows 2x and 4x
zoom.
Snapshot Capture a snapshot image of the
video displayed on screen by clicking this
icon.
Audio Disabled This icon indicates that
audio is not enabled on the device.
Video Format This icon allows you to select
the video format of the video being captured
by the camera.
Business Internet Video Camera with Audio
18
Advanced Configuration
Chapter 6
Resolution
PC’s Date and Time Displays the current time of the PC
connected to the web-based utility.
Setup > Basic Setup
Camera Date and Time Displays the current time as
configured on the camera.
Sync with PC This option allows you to synchronize the
camera to the clock on the PC connected to the web‑based
utility.
New Date This option allows you to manually enter the
date for the camera.
New Time This option allows you to manually enter a
new clock setting for the camera.
Set New Time Use this button to implement the new
date and/or time setting.
Time Zone Choose the time zone for your location from
the drop-down list.
Adjust for Daylight Saving Time Select this option if
your location is currently using Daylight Saving Time.
NOTE: You must uncheck the Adjust for Daylight
Saving Time check box manually when Daylight
Saving Time ends in your time zone.
Setup > Basic Setup
Device Settings
Device ID This displays the ID for the Camera. This is used
by the setup wizard, viewer and the recorder utility to
identify the Camera.
Camera Name Enter the preferred name for the Camera.
The camera name must not exceed 15 alphanumeric
characters.
Description This field is used for entering a description,
such as the location of the Camera. Entering a description
will help you identify the Camera. It must not exceed 32
alphanumeric characters.
Check here if you want to update the time automatically
through the NTP Server on the Internet Enable or
disable the time server feature as required. If enabled,
the Camera will contact a network time server at regular
intervals and update its internal timer.
NTP Server Address Enter the address of the NTP
Server.
NTP Port The default NTP port is 123. If using a different
port, enter the NTP port number (1024 to 65535) in the
field provided.
Bonjour Name Enter the preferred name for identifying
your Bonjour connection.
NOTE: If connecting to a router, it may be
necessary to enable port forwarding.
Enable LED Operations Enable this if you want to turn
on the LED.
Current Date/Time It displays the current date and time.
If it’s not correct, click the Change button to modify the
time settings.
Network Settings
Set Date/Time
•
Obtain An IP Address Automatically The camera
defaults to this option, allowing a DHCP server on
your network to automatically assign the Camera an
IP address.
•
Fixed IP Address Use this option to assign a fixed
(static) IP address to the Camera. Assign an IP address
that is unique to your local network. When using a
fixed IP address, you must configure the IP Address,
Subnet Mask, Gateway and DNS.
Configuration Type
Setup > Basic Setup > Set Date/Time
Business Internet Video Camera with Audio
19
Advanced Configuration
Chapter 6
IP Address The IP address assigned to the Camera is
displayed.
TX Key Select the number of the key used on the wireless
network.
Subnet Mask The Subnet Mask assigned to the Camera
is displayed.
WEP Encryption Select the appropriate option for key
length based on your network settings.
Gateway IP address of the gateway router between this
device and management stations that exist on other
network segments.
Passphrase Type in the passphrase used to generate WEP
keys on your network and click the Generate button.
Primary DNS The IP address of your ISP’s primary server,
which translates the names of websites into IP addresses.
Secondary DNS The IP address of your ISP’s secondary
server, which translates the names of websites into IP
addresses.
Wireless Settings
Key 1-4 Key values can be entered in manually or
generated from a passphrase.
Authentication Select the appropriate authentication
type used on the wireless network.
WPA /WPA2 Personal
This method offers two encryption methods, TKIP and
AES, with dynamic encryption keys
NOTE: The wireless settings are only found on
the WVC2300 camera.
SSID Enter the network’s SSID or network name here.
Network Type Select the network’s mode, Infrastructure
or Ad-hoc.
Channel No If the Camera is set to ad-hoc mode, select
its channel setting from the drop-down menu.
Security Click the Edit Security Settings button to
display the Wireless Security screen.
Security Mode
Select the appropriate option based on your wireless
network configuration.
Wireless Security > Security Mode > WPA /WPA2 Personal
Encryption This cannot be modified.
Shared Key Enter the shared key used for accessing the
wireless network.
WPA /WPA2 Enterprise
The screen options vary depending upon the protocol
type selected.
Protocol Type Select EAP-TLS or EAP-TTLS.
Disabled
This option implements no security on your wireless
network. Data is not encrypted before transmission.
WEP
WEP is a basic encryption method, which is not as secure
as later methods such as WPA-Personal or WPA2 Personal.
However, it is supported by all clients.
Wireless Security > Security Mode > WPA /WPA2 Enterprise (EAP-TLS)
•
User ID The user ID used to login to your RADIUS
server.
•
Root CA A root certificate is an unsigned public key
certificate, or a self-signed certificate, which implies
that you trust your browser’s publisher to include
correct root certificates, and in turn the certificate
authorities it trusts, and anyone to whom the CA may
have issued a certificate-issuing-certificate, to faithfully
authenticate the users of all their certificates.
•
User CA A user certificate is a signed private key
Wireless Security > Security Mode > WEP
Business Internet Video Camera with Audio
20
Advanced Configuration
Chapter 6
•
certificate, which implies that you trust your browser’s
publisher to include correct user certificates, and in
turn the certificate authorities it trusts, and only user
to whom the CA may have issued a certificate-issuingcertificate, to faithfully authenticate the users of all
their certificates.
HTTP/HTTPS
Password This is for this Camera’s client login to the
RADIUS server, and must match the key stored on the
RADIUS server.
The port number must be specified in the URL when
accessing the Camera’s web-based utility via the LAN
or Internet. For example, if the Camera’s IP address is
192.168.1.99 and the port is defined as 1028, you would
specify the following address: http://192.168.1.99:1028.
Enable HTTP Alternative Port This option allows you to
define the port number used to communicate with the
camera using an HTTP connection. The default value is
1024. A value in the range of 1024-65535 can be defined.
Enable HTTPS Alternative Port This option allows you
to define the port number used to communicate with the
camera using an HTTPS connection. The default value is
1024. A value in the range of 1024-65535 can be defined.
When using a secure connection, video is not available.
This option is used only for configuration.
Wireless Security > Security Mode > WPA /WPA2 Enterprise (EAP-TTLS)
•
Process Method Choose an authentication method
as required to handle the processing and transmitting
of CA to your RADIUS server.
•
User ID The user ID used for login to your RADIUS
server.
•
Password This is for this Camera’s client login to the
RADIUS server.
•
Anonymous ID The unsigned public ID used for login
to your RADIUS server.
•
Root CA A root certificate is an unsigned public key
certificate, or a self-signed certificate, which implies
that you trust your browser’s publisher to include
correct root certificates, and in turn the certificate
authorities it trusts, and anyone to whom the CA may
have issued a certificate-issuing-certificate, to faithfully
authenticate the users of all their certificates.
The port number must be specified in the URL
when accessing the Camera’s web-based utility via
the LAN or Internet. For example, if the Camera’s
IP address is 192.168.1.99 and the port is defined
as 1032, you would specify the following address:
https://192.168.1.99:1032
Setting Up Port Forwarding
After configuring a port in the web-based utility of the
Camera, most users will need to set up port forwarding
on their router. The following are the steps for configuring
port forwarding on a WRT54G router (other routers should
be similar, consult your router’s documentation):
1. In the Camera’s web-based utility, go to the Setup
> Advanced Setup screen. The option Enable HTTP
Alternative Port must be enabled and the desired port
value entered. In this example, port 1028 has been
configured. Valid port settings are 1024-65535.
Setup > Advanced Setup
Setup > Advanced Setup
Business Internet Video Camera with Audio
21
Advanced Configuration
Chapter 6
2. Enter the IP address of your router in your web
browser’s Address field and press Enter. In this example,
the default IP address of the WRT54G router is used
(192.168.1.1).
3. Enter the login name and password to access the
router’s web-based utility.
4. In the web-based utility, go to the Applications &
Gaming tab.
RTSP Port Enter the RTSP Port number (between 1024 to
65535) in the field provided. The default RTSP port is 554.
RTP Data Port The Camera’s data port number has been
pre-configured and can be used for multicasting. It does
not normally need to be re-configured. If a port number
does need to be changed, please contact your network
administrator. If a change is necessary, enter the data port
number (1024 to 65535) in the field provided. The default
RTP port is 5000.
Max RTP Data Packet This allows you to define the
maximum size of the RTP data packets. The length can
be between 400 to 1400 bytes. The default value is 1400
bytes.
Enable Multicast The Camera’s Video and Audio IP
Addresses have been pre-configured and can be used
for multicasting. Normally these settings do not need to
be reconfigured. If an address does need to be changed,
please contact your network administrator.
Advanced Setup > RTP/RTSP > Enable Multicast
WRT54G Web-Based Utility
5. On the Port Range Forward screen, enter the Application
name such as Camera.
6. Enter the Start and End port, in this instance 1028 is
used.
7. Ensure the Protocol set to Both.
8. Complete the IP address of the Camera, such as 99 in
the field provided.
9. Click the Save Settings button at the bottom of the
screen to save the configuration to the router.
Once port forwarding has been configured, the router can
be accessed over the Internet by typing in the Internet
IP address of the router, a colon, and the defined port
number in the following format: http://ipaddress:port
RTP/RTSP
RTSP (Real Time Streaming Protocol) is a standard for
connected client(s) to control streaming data (MPEG-4)
over the World Wide Web.
RTP (Real-Time Transport Protocol) is an Internet protocol
used for transmitting single real-time multimedia data
such as audio and video to a select group of connected
clients. RTSP uses RTP to format packets of multimedia
content.
Business Internet Video Camera with Audio
•
Video Address Enter the address.
•
Video Port Enter the port number.
•
Audio Address Enter the IP address.
•
Audio Port Enter the port number.
•
Time to Live Define the number of hops (the number
of network routers that can be passed before the
multimedia data packets arrive at their destination
or are dropped) that can occur before the packets
are dropped. A value in the range of 1 to 255 can be
defined. The default value is 16.
UPnP
Enable Discovery If enabled, the Camera will broadcast
its availability through UPnP. UPnP compatible systems
such as Windows XP will then be able to detect the
presence of the Camera.
Enable Traversal (Port Mapping) If enabled, HTTP
connections (from your web browser, viewer and recorder
utility) can use an alternative port instead of port 80 (the
standard HTTP port) to access the Camera.
Bonjour
Enable Bonjour If enabled, the Camera will be accessible
through Bonjour connections.
22
Advanced Configuration
Chapter 6
QoS
•
Enable QoS Mode QoS (Quality of Service) mode is
disabled by default. To enable QoS mode, select this
option and select either audio or video for its guaranteed
throughput level. Enable QoS mode will automatically
enable WMM (802.11e QoS) when in wireless mode.
Enable and Allow the Following IP Address This
option will allow only the IP addresses specified here
to access the camera. Choose Single to enter a specific
IP address or Range to enter a range of IP addresses.
Up to 10 values can be configured.
Administration > Users
*WMM (Wi-Fi Multimedia) is a standard created to define
quality of service (QoS) in Wi-Fi networks. It is a precursor to
the IEEE 802.11e WLAN QoS draft standard, which is meant to
improve audio, video and voice applications transmitted over
Wi-Fi. WMM adds prioritized capabilities to Wi-Fi networks
and optimizes their performance when multiple concurring
applications, each with different latency and throughput
requirements, compete for network resources.
CoS
Enable CoS Mode CoS (Class of Service) mode is disabled
by default. To enable CoS mode, please check the check
box. Priority Priority can be set to a value between 0 to 7. The
highest priority value is 7.
VLAN ID Enter the VLAN ID (0 to 4095) in the field
provided.
Setup > IP Filter
Administration > Users
The Setup > IP Filter screen can be used to deny or allow a
specific IP address or range of IP addresses.
Administrator
Admin The default administrator name cannot be
changed but the password can and should be changed
for security purposes. To change the password, enter the
desired password in the Password and Confirm Password
fields. Click the Change button to apply the change.
Demo
Viewer This account can is used to allow the viewing
of video only. By default the account name is demo and
there is no password assigned. To change the demo
account settings, modify the user name and password in
the appropriate fields and click the Change button.
Setup > IP Filter
Options There are three options to choose from:
User List
User ID The User ID cannot be modified.
•
Disable This option disables IP filtering function.
User Name Enter the desired user name.
•
Enable and Deny the Following IP Address This
function will allow you to deny access to a specific IP
address or range of IP addresses. Choose Single to
enter a specific IP address or Range to enter a range of
IP addresses. Up to 10 values can be configured.
Password Enter the desired password in this field.
Business Internet Video Camera with Audio
Confirm Password Retype the password in this field.
23
Chapter 6
Privilege Level Select the appropriate privilege level
from the drop-down menu. Choose from one of the
following options:
•
Administrator This option provides the specified
user with full Camera administration and control
privileges.
•
Monitor This option grants the specified user with
control of the Camera video (manually pan/tilt, toggle
between day/night vision, and trigger output ports).
•
Viewer This option grants the specified user with
video viewing privileges only.
Advanced Configuration
Administration > Firmware
Click the Add button to add a new User ID or click the
Delete button to remove an existing User ID.
Administration > Maintenance
Administration > Firmware
Firmware Upgrade
Upgrade This option is used to update the Camera’s
firmware. To update the firmware, perform the following
steps:
1. Download the latest firmware for the Camera to your
computer from www.linksys.com.
2. Click the Upgrade button to open the Upgrade
Firmware window.
3. Click the Browse button to locate the firmware
upgrade file.
Administration > Maintenance
Restore Factory Defaults
Restore This option restores the Camera to the factory
default settings.
Restart
4. Click the Upgrade button to begin the firmware
upgrade.
WARNING: Do not disconnect the power to the
camera during the upgrade process.
Audio/Video > Video
Restart This option restarts the Camera.
Configuration
Save Use this option to save a configuration file containing
all of the current Camera management settings.
Browse Use this option to locate a previously saved
configuration file.
Upload Use this button to upload a previously saved
configuration file into the Camera.
Audio/Video > Video
Business Internet Video Camera with Audio
24
Advanced Configuration
Chapter 6
NOTE: Higher video quality settings and higher
frame rate settings require more bandwidth.
Refer to the Appendix titled “Bandwidth Usage”
for additional details.
MPEG-4 Settings
Resolution Select the desired video resolution setting.
The default resolution is set to 320x240.
Video Quality Control Choose one of the following:
•
Constant Bit Rate Select the desired fix bit rate. The
default bit rate is set to 256 Kbps.
•
Fix Quality Select the desired fix quality. The default
fix quality is set to Normal.
Max Frame Rate Select the desired maximum frame rate.
The default maximum frame rate is set to 30 fps.
MJPEG Settings
Brightness If necessary, you can adjust the brightness to
obtain a better image. For example, if the camera is facing
a bright light, the image may be too dark. In this case, you
can increase the brightness.
Sharpness Select the desired option for the sharpness.
You can select a sharpness value between -3 and 3.
Contrast Select the desired option for the contrast. You
can select a contrast value between -3 and 3.
Options
Enable Time Stamp If you want to display a time stamp
on the video, enable this feature by checking the check
box.
Enable Text Display If you want to display text on the
video, enable this feature by checking the check box. The
text can be up to 20 characters in length. This feature is
often used to identify the Camera location when multiple
Cameras are installed.
Resolution Select the desired video resolution format.
The default resolution is set to 320x240.
Enable Image Overlay If you want to display an image
on the video, enable this feature by checking the check
box.
Fixed Video Quality Select the desired fix quality. The
default fix quality is set to Normal.
•
Mobile Settings
Linksys Logo This option will display a Linksys
logo on top of the video. Positioning of the logo is
determined by the x and y coordinates defined in the
Image Position fields. Be sure not to define a position
that is outside of the defined resolution.
•
Enable Mobile Streaming Enable streaming video for
the mobile devices by selecting this option.
User Defined Image This option allows you to upload
a bitmap image file (smaller than 64Kb).
•
Image Position The Image Position fields allow you
to define the coordinates of the Linksys logo or user
defined image. The upper left corner value is 0, 0.
Increasing the X value (X: 0 - 639) will move the image
to the right. Increasing the Y value (Y: 0 - 479) will move
the image down.
Frame Rate Control Select the desired frame rate. The
default frame rate is set to Auto.
•
Resolution The default resolution is set to 160x120.
•
Video Quality Control Choose from one of the
following options:
–
Constant Bit Rate Select the desired fix bit rate.
The default bit rate is set to 32 Kbps.
–
Fix Quality Select the desired fix quality. The
default fix quality is set to Normal.
•
Max Frame Rate Select the desired maximum frame
rate. The default maximum frame rate is set to 15 fps.
•
Access Code Enter a code to use to access the live video
from the Camera through cell phone connection.
NOTE: Select values within the range of the
selected image resolution.
Video Adjustments
Power Line Frequency Select the power line frequency
(50Hz or 60Hz) used in your region, to improve the picture
quality under fluorescent lighting.
White Balance Select the suitable white balance option
as you desired.
Business Internet Video Camera with Audio
25
Advanced Configuration
Chapter 6
Audio/Video > Audio
0 - 479
Y Coordinate
X Coordinate
0 - 639
Image Position
•
Transparent Color This option allows you to define
a color that should appear transparent. This allows a
logo or other image to appear over the video without
displaying a solid background color. The color value
must be entered in RGB hexadecimal color code, such
as 0000ff.
Audio/Video > Audio
Audio Settings
Enable Audio Enable audio by checking the check box.
Audio Settings
Day/Night Switch
Mode
Function
Simplex - Talk Only
Enables the speaker jack
Color cameras can capture infrared radiation as well as
visible light. The Camera is equipped with an IR-cut filter
that prevents distortion of colors the human eye can
see. To use the Camera in locations with poor lighting or
at night, the IR-cut filter can be manually turned off or a
schedule can be used to turn off the filter at a set time.
An infrared lamp can be used to improve illumination in
night surveillance applications without producing any
extra visible light. This is all done by using the IR filter
switcher that is built-in to the camera.
Simplex - Listen Only
Enables the microphone jack
Enable Night Vision Schedule Enable Day / Night switch
schedule by checking this check box.
•
Start Time Select the evening start time by selecting
the hour and minute (uses 24 hour time format).
•
End Time Enter the hour in the morning to end the
night vision feature, by selecting the hour and minute
(uses 24 hour time format). Business Internet Video Camera with Audio
Half Duplex - Talk or Listen Enables the speaker and
(Not simultaneously)
microphone jack but only one
can be used at a time
Full Duplex - Talk and Listen Enables the speaker and
(Can be simultaneously)
microphone jack and both can
be used simultaneously
Audio Type When the microphone is enabled, this
drop‑down menu allows you to select the audio
compression type.
Compression Settings
Setting
Description
G.726
Default audio compression algorithm, uses
32 Kbps of bandwidth with quality similar to
G.711 but using only half of the bandwidth
G.711 A-Law
A standard compression algorithm that uses
64 Kbps of bandwidth and is primarily used in
Europe
G.711 µ-Law
A standard compression algorithm that uses
64 Kbps of bandwidth and is primarily used in
North America and Japan
26
Advanced Configuration
Chapter 6
Applications > Mail & FTP
Authentication Choose from one of the following
options:
•
Not Required Authentication is not required in order
to send mail.
•
Requires SMTP Authentication Select this if the
SMTP Server requires a “login” to send mail.
•
Requires POP before SMTP Select this if the SMTP
Server requires a POP “login” to send mail.
E-mail Setup
Send To Enter at least one (1) e-mail address; the 2nd and
3rd addresses are optional. The e-mail alert will be sent to
the e-mail address or addresses specified here.
Show “From” as Enter the e-mail address to be shown in
the From field when the e-mail is received.
Subject Enter the desired text to be shown as the subject
for the E-mail when it is received
E-mail Body
Attach Video Streaming URL Address This option
includes the streaming video URL address in the E-mail
alert, when the recorded video file is too big to be sent.
Applications > Mail & FTP
Mail
NOTE: Only one SMTP server is used, even if
both the primary and secondary SMTP servers
are enabled.
Primary SMTP Server
Primary SMTP Check the box to upload to the Primary
SMTP.
FTP
NOTE: Only one FTP server is used, even if both
the primary and secondary FTP servers are
enabled.
Primary FTP
Primary FTP Check the box to upload to the Primary
FTP.
FTP Server Enter the address of the primary FTP Server.
SMTP Mail Server Enter the address of the SMTP (Simple
Mail Transport Protocol) Server to be used to send E-mail.
Login Name Enter the login name associated with the
specified primary FTP server.
Authentication Choose from one of the following
options:
Password Enter the password associated with the login
name for the primary FTP server.
•
Not Required Authentication is not required in order
to send mail.
File Path Name Enter the desired file path name on the
primary FTP server.
•
Requires SMTP Authentication Select this if the
SMTP Server requires a “login” to send mail.
Enable Passive Mode Check the box to enable the
Passive mode feature.
•
Requires POP before SMTP Select this if the SMTP
Server requires a POP “login” to send mail.
Secondary FTP
Secondary SMTP
Secondary SMTP Check the box to upload to the
Secondary SMTP if the camera can not connect to the
primary SMTP.
Business Internet Video Camera with Audio
Secondary FTP Enable this option to allow the camera
to connect to a secondary FTP server if the primary FTP
server is not available
FTP Server Enter the address of the secondary FTP
Server.
27
Advanced Configuration
Chapter 6
Login Name Enter the login name associated with the
secondary FTP server.
NOTE: Motion detection can be triggered by
rapid changes in lighting conditions, as well
as by moving objects. For this reason, it should
only be used indoors.
Password Enter the password associated with the login
name for the secondary FTP server.
File Path Name Enter the desired file path name on the
secondary FTP server.
Enable Passive Mode Check the box to enable the
Passive mode feature on the secondary FTP server.
When you first select the Motion Detection option, you will
be prompted to install an Active-X plug-in. It is necessary
to install this plug-in to use this feature.
Applications > Instant Messaging
Applications > Motion Detection (Install Active-X)
Applications > Instant Messaging
Jabber
Enable Jabber When enabled, an open XML protocol for
message and presence exchange in real time between
two points on the Internet. Jabber asynchronous instant
messaging (IM) platform is similar to IM systems such as
AIM, ICQ and MSN but is open source, extensible through
XML, decentralized (allowing anyone to run a Jabber
server), and any Jabber server can be isolated from the
public Jabber network in order to increase security.
Active-X Message
Server Enter the address of your Jabber server.
Login ID Enter the login name for your Jabber server.
Password Enter the password for your Jabber server
Send To The log will be sent to the e-mail address you
specified here.
Message Enter the message you wish to attach.
Applications > Motion Detection
NOTE: Motion detection cannot be configured
using the Firefox browser. Internet Explorer
must be used to configure motion detection.
Applications > Motion Detection
Full Screen Enable this option to detect motion events
within the full view of the screen.
•
Indicator This area displays the level of motion
detected. This option cannot be configured but is
useful for determining a motion threshold.
•
Sensitivity Use this to adjust the motion sensitivity.
You can set the area(s) of the video image to be examined,
and adjust the sensitivity of detection for each area.
Business Internet Video Camera with Audio
28
Advanced Configuration
Chapter 6
Setting Custom Area Enable this option to capture
motion within defined areas of the video screen. Multiple
windows with varied threshold settings may be used.
•
Window 2-4 Enable one or more of these options to
detect motion in specific areas of the video screen.
Windows can be defined by simply extending the
window with the cursor. More than one window can
be used at once.
•
Indicator This area displays the level of motion
detected. This option cannot be configured but is
useful for determining a motion threshold.
•
Sensitivity Use this to adjust the motion sensitivity.
New Schedule
NOTE: The Network Camera can be configured
for up to 10 events.
Effective Time Frame Select the event time frame,
available options are every day, weekdays, or a specific
day of the week.
Start Time Select the event start time in hours and
minutes (use the 24 hour time format).
End Time Select the event end time in hours and minutes
(use the 24 hour time format).
Applications > Event
Trigger Event
This tab is used to set up the Internet Camera applications
functions. Operating Mode allows you to configure Event
Trigger settings as you desired.
Enable Check to perform all of the event(s) that were
configured and scheduled.
A triggered event is a set of parameters describing how
and when the Network Camera will perform certain
triggered actions, according to requirements.
The most common kind of event type will upload video or
snapshot files to a specified destination (E-mail account or
FTP server). Other actions performed by event types can
include the activation of an output port.
NOTE: It is important to note that adding a
new event will stop any event that is currently
running. A scheduled event will automatically
resume, if the time is still within the scheduled
period. A triggered event will need to be retriggered.
Interval Select the desired option for the events interval.
(* “0 sec” = No Delay)
Triggered by Select a trigger option:
•
Input 1/2 This describes the states that the input(s)
must be in for an event to be triggered. Only one input
can be used, also note that the states for all the inputs
used must first be reached before the event will be
triggered.
•
Motion Detection Movement in a motion detection
window can be used to trigger events. Select the
motion detection window from the drop-down list.
Action(s) Select one or more actions to perform once a
trigger event occurs, choose from the following options:
•
E-mail Send an e-mail to the account configured from
the Applications > Mail & FTP screen.
•
FTP Upload the images to the primary or secondary
FTP server defined on the Applications > Mail & FTP
screen.
•
Output 1/2 These options are configured from the
Applications > I/O Ports screen.
•
Instant Messaging These options are configured
from the Applications > Instant Messaging screen.
Event Attachment
Applications > Event
Event Schedule
The Event Schedule displays the effective time frame and
start/end times for scheduled events.
Business Internet Video Camera with Audio
Applications > Event > Event Attachment
When trigger events are enabled and an e-mail or FTP
action is selected, the following options are enabled:
29
Advanced Configuration
Chapter 6
Overwrite/Replace oldest video file Check to overwrite/
replace the oldest video clip with the current recording
when detecting device’s SDRAM is full.
Attachment Type Select the type of attachment:
•
•
JPEG Image Select this to send image captures.
–
Frame Rate Select the desired capture rate for the
JPEG image(s) here.
–
Pre/Post Capture Select the desired length.
The snapshot(s) of the JPEG image depends on
this setting, and also the file size and degree of
compression.
Host Name Enter the host name (Domain Name)
allocated to you by the DDNS Server provider.
Account Enter the login name for the DDNS account.
Password Enter the password for the DDNS account.
Check WAN IP Address This option allows you to set
how often the device should check to see if the Internet
IP address has changed. If the IP address has changed, the
DDNS Server will be notified.
NOTE: To complete the DDNS Service setup,
port forwarding needs to be configured on
your router.
Video
–
Video Format - (MPEG-4 Mode Only) Select the
desired type for the video file.

ASF (This file format cannot be used in
Windows Vista)

MP4 (no audio)

3GP (no audio)
Applications > I/O Ports
Pre/Post Capture Select the desired length. The size of
the file depends on this setting, and also the Video size
and degree of compression.
Applications > DDNS
Applications > I/O Ports
See Appendix D: Specifications > I/O Port Specifications for
additional details.
Input Ports
# Displays the port number.
Current State Indicates the current status of input device
(ex. Alarm Sensor or Smoke Sensor) that you connected.
Applications > DDNS
DDNS
Enable DDNS This option will enable Dynamic Domain
Name Service (DDNS). When used with a DDNS service
provider, you can access your camera over the Internet
using a domain name instead of an IP address.
Service Provider Select the service provider that you
have an account with. If you do not have an account,
you can select a service provider and click the Web Site
button.
Business Internet Video Camera with Audio
Triggered When There are 4 triggering conditions
that can be set. The input port will be activated if the
triggering condition changes so that it no longer equals
to the current state.
•
High
•
Low
•
Rising
•
Falling
30
Advanced Configuration
Chapter 6
Output Ports State at Power On
In the Camera, as long as both output’s Default and Current
State is High, the output is disconnected (floating). When
the current State changes to Low or Low Pulse, the output
will be activated.
Parity Select the desired parity type for the device you
connected.
Stop Bits Select the desired stop bits for the device you
connected.
# Displays the port number.
Address Enter the valid logical address of the receiver/
driver being controlled.
Current State Displays the current state of the port.
Preset Position
Default State The default setting for the Default State
option is High. While the Camera is restarting, the output
will be in the Default State (i.e. High) for at least as long as
it takes for the Camera to fully initialize. Please consider
this carefully when connecting equipment to the output.
After a full restart, the unit will then switch to Low or Low
Pulse (but only if configured to do so).
Set Preset Position This button will bring up the Set
Pan/Tilt screen that allows you to define the preset point
position.
Output State Changing and saving Output State settings
on this page will also reset outputs to their Default States.
The state will be correct the next time the triggering event
activates the output.
Output Ports Manual Control
# Displays the port number.
Action Definition Defines the output port mapping.
Applications > RS-485
Pan/Tilt
Set Home Set the desired position and then click this
button to define the home position.
Preset List Select the desired preset position, the screen
will update with the current data for the selected preset.
If you don’t need the desired preset position, click the
Remove button to remove.
Preset Name Enter a suitable name for the current
desired position and then click the “Add” button to add
into the preset list.
Pan Speed Select the desired speed for camera panning.
Tilt Speed Select the desired speed for camera tilting.
Patrol Sequence
This feature determines how the camera will move when
it is set to Rotate. You can set a number of preset positions;
the camera will go to the first position, then move through
the list of preset positions until it is finished. The camera
will stop at the last position in the list.
To create the preset sequence, select the desired Preset in
the left column, and click the Add >> button. Repeat until
the desired sequence is complete.
Applications > RS-485
Enable RS485 If the RS485 feature is enabled, valid
command(s) must be provided as requested by the
connected device(s).
Port Settings
Baud Rate Select the desired baud rate for the device
you connected.
Data Bits Select the desired data bits for the device you
connected.
Business Internet Video Camera with Audio
NOTE: You can add the same preset position
more than once; this can be used to make the
camera stay longer at one position.
To delete a position from the sequence, select the desired
position and click the Remove button.
Preset Displays a list of available presets to choose from.
Sequence Displays the order of presets in the sequence.
Add >> Use this button to add a preset to the sequence.
Remove Use this option to remove a preset from the
sequence.
31
Advanced Configuration
Chapter 6
Status > System
Image Quality This displays the image quality of the
video stream.
Frame Rate This displays the frame rate of the video
stream.
MJPEG
Resolution This displays the image size of the video
stream.
Image Quality This displays the image quality of the
video stream.
Frame Rate This displays the frame rate of the video
stream.
Status > System
Status > Network
System Status
Firmware Version The version of the firmware currently
installed is displayed. Firmware can be upgraded from the
Administration > Firmware screen. You must be logged in
with administrator privileges to upgrade the firmware.
MAC Address This displays the MAC address of the
camera.
Camera Name This displays the name of the camera, as
defined on the Setup > Basic Setup screen.
Description This displays the description of the camera,
as defined on the Setup > Basic Setup screen.
Date/Time This displays the current date/time as
configured on the camera.
Status > Image
Status > Network
Network
Network Type This displays the type of network the
camera is connected to.
IP Address This displays the IP address assigned to the
camera.
Subnet Mask This displays the subnet mask assigned to
the camera.
Gateway This displays the IP address of the gateway used
by the camera.
Primary DNS This displays the IP address of the primary
Domain Name Server used by the camera.
Secondary DNS This displays the IP address of the
secondary Domain Name Server used by the camera.
Status > Image
MPEG-4
Resolution This displays the image size of the video
stream.
Business Internet Video Camera with Audio
Wireless
NOTE: Wireless information is only found on
the WVC2300 camera.
32
Advanced Configuration
Chapter 6
SSID This displays the wireless network name (SSID) used
by the camera.
Status > Video Log
Channel This displays the wireless channel used by the
camera.
Security This indicates if wireless security is being used
by the camera.
Status > Syslog & Log
View Video Log
Video Log
Refresh Click this button to reload all the entries in the
video log.
Status > Syslog & Log
Delete All Click this button to erase all the entries in the
video log.
Log
Log Type Place a check mark next to the types of logs
that you wish to view on the Log List.
•
System Log
•
FTP Log
•
SMTP Log
•
IM Log
Syslog
Enable Syslog Server Select this to enable the Syslog
server.
Syslog Server Address Enter the IP address of your
Syslog server.
Syslog Port Enter the Syslog port number (between
1024 to 65535) in the field provided. The default Syslog
port is 514.
Log List
Refresh Click this button to reload all the entries in the
System Log.
Clear Log Click this button to erase all the entries in the
System Log.
Business Internet Video Camera with Audio
33
Troubleshooting
Appendix A
Appendix A:
Troubleshooting
The motion detection feature doesn’t send me any
E‑mails.
This appendix provides solutions to problems that may
occur during the installation and operation of the Business
Internet Video Camera. Read the questions and answers
below to solve your problems:
It may be that the SMTP (Simple Mail Transport Protocol)
server used by the Camera to send the E-mail will not
accept mail. This is to prevent Spam being sent from the
server. Try using a different SMTP server, or contact your
ISP to see if SMTP access is being blocked or if they do not
allow SMTP relay (sending to another e-mail address).
I can’t connect to the Camera with my web browser to
configure it.
Using the motion detection feature, I receive E-mails
which don’t show any moving objects.
It is possible that your PC’s IP address is not compatible
with the IP address of the Camera. Use the Windows utility
to configure the Camera with a valid IP address.
The motion detection feature doesn’t actually detect
motion. It compares frames to see if they are different.
Major differences between frames are assumed to be
caused by moving objects. The motion detector can also
be triggered by sudden changes in the level of available
light or movement of the camera itself.
When I try to connect to the Camera, I get prompted for
a user name and password.
You SHOULD be prompted for a user name and password
when you first connect to the Camera. Enter the
Administrator ID and Password set on the Administration >
Users screen. The User Name/Password prompt indicates
that the Administrator has restricted access to specified
users. Ask the Administrator for your User Name and
Password.
I can’t connect to the Camera using a Wireless
connection.
NOTE: Wireless connections are only supported
on the WVC2300 camera.
If a LAN cable is connected to the LAN port, the Wireless
interface is disabled. Only one interface can be active.
Check that your PC and the Camera have compatible
Wireless settings.
•
Mode (Infrastructure or Ad-hoc) must be correct.
•
The Camera’s SSID must match the network SSID.
•
Encryption settings must match.
•
In Ad-hoc mode, the channel should match.
Try to avoid these situations. The motion detection
feature works best in locations where there is good steady
illumination, and the Camera is mounted securely.
The image is blurry.
Try the following options:
•
Focus the lens.
•
Check to make sure the lens is clean.
•
Adjust the quality on the Audio/Video > Video screen.
Video created with lower settings will contain less
detail; this is the trade-off for using less bandwidth.
WEB: If your questions are not addressed here,
refer to the Linksys website, www.linksys.com
Video quality suddenly deteriorates.
This can happen when an additional viewer connects
to the Camera, overloading the Camera or the available
bandwidth. The image size and quality can be adjusted
to cater to the required number of viewers and available
bandwidth.
Business Internet Video Camera with Audio
34
Bandwidth Usage
Appendix B
Appendix B:
Bandwidth Usage
WVC2300 Bandwidth Test
Audio: ON
One User viewing video
Resolution
Quality
Very High
640 x 480
Normal
Very Low
Very High
320 x 240
Normal
Very Low
Very High
160 x 128
Normal
Very Low
Business Internet Video Camera with Audio
Frame Rate
Bandwidth (k/bps)
MPEG-4
MJPEG
30
2320
3040
15
1840
2800
6
880
1840
30
2240
2800
15
1680
2640
6
640
1600
30
2160
2640
15
1200
2400
6
560
1200
30
1600
2000
15
1200
1600
6
600
800
30
1440
1840
15
800
1440
6
360
640
30
760
1600
15
480
1200
6
200
480
30
1600
1440
15
1120
800
6
560
320
30
560
1200
15
320
640
6
160
280
30
320
1040
15
200
560
6
120
240
35
Glossary
Appendix C
Appendix C:
Glossary
Baud Indicates the number of signaling elements
transmitted each second.
This glossary contains some basic networking terms you
may come across when using this product.
Bit A binary digit.
WEB: For additional terms, please visit the
glossary at www.linksys.com/glossary
Access Mode Specifies the method by which user access
is granted to the system.
Access Point A device that allows wireless-equipped
computers and other devices to communicate with a
wired network. Also used to expand the range of a wireless
network.
Access Profiles Allows network managers to define
profiles and rules for accessing the device. Access to
management functions can be limited to user groups,
which are defined by the following criteria:
•
Ingress interfaces
•
Source IP address and/or Source IP subnets.
ACE Filters in Access Control Lists (ACL) that determine
which network traffic is forwarded. An ACE is based on the
following criteria:
•
Protocol
•
Protocol ID
•
Source Port
•
Destination Port
•
Wildcard Mask
•
Source IP Address
•
Destination IP Address
ACL (Access Control List) Access Control Lists are
used to grant, deny, or limit access devices, features, or
applications.
Auto-negotiation Allows 10/100 Mbps or 10/100/1000
Mbps Ethernet ports to automatically establish the
optimal duplex mode, flow control, and speed.
Back Pressure A mechanism used with Half Duplex mode
that enables a port not to receive a message.
Bandwidth The transmission capacity of a given device
or network.
Bandwidth Assignments Indicates the amount of
bandwidth assigned to a specific application, user, and/or
interface.
Business Internet Video Camera with Audio
Best Effort Indicates that traffic is assigned to the lowest
priority queue, and packet delivery is not guaranteed.
Boot To start a device and cause it to start executing
instructions.
Browser An application program that provides a way to
look at and interact with all the information on the World
Wide Web.
Bridge A device that connect two networks. Bridges are
hardware specific, however they are protocol independent.
Bridges operate at Layer 1 and Layer 2 levels.
Broadcast Domain Devices sets that receive broadcast
frames originating from any device within a designated
set. Routers bind Broadcast domains, because routers do
not forward broadcast frames.
Broadcast Storm An excessive amount of broadcast
messages simultaneously transmitted across a network
by a single port. Forwarded message responses are
heaped onto the network, overloading network resources
or causing the network to time out.
Burst A packet transmission at faster than normal rates.
Bursts are limited in time and only occur under specific
conditions.
Burst Size Indicates the burst size transmitted at a faster
than normal rate.
Byte A unit of data that is usually eight bits long
Cable Modem A device that connects a computer to the
cable television network, which in turn connects to the
Internet.
CBS (Committed Burst Size) Indicates the maximum
number of data bits transmitted within a specific time
interval.
CIR (Committed Information Rate) The data rate is
averaged over a minimum time increment.
Class Maps An aspect of Quality of Service system that is
comprised of an IP ACL and/or a MAC ACL. Class maps are
configured to match packet criteria, and are matched to
packets in a first-fit fashion.
Combo Ports A single logical port with two physical
connections, including an RJ-45 connection and a SFP
connection.
Communities Specifies a group of users which retain the
same system access rights.
36
Appendix C
CoS (Class of Service) The 802.1p priority scheme. CoS
provides a method for tagging packets with priority
information. A CoS value between 0-7 is added to the
Layer II header of packets, where zero is the lowest priority
and seven is the highest.
DDNS (Dynamic Domain Name System) Allows the
hosting of a website, FTP server, or e-mail server with a
fixed domain name (e.g., www.xyz.com) and a dynamic IP
address.
Default Gateway A device that forwards Internet traffic
from your local area network.
DHCP (Dynamic Host Configuration Protocol) A
networking protocol that allows administrators to assign
temporary IP addresses to network computers by “leasing”
an IP address to a user for a limited amount of time, instead
of assigning permanent IP addresses.
DHCP Clients An Internet host using DHCP to obtain
configuration parameters, such as a network address.
DHCP Server An Internet host that returns configuration
parameters to DHCP clients.
DNS (Domain Name Server) The IP address of your ISP’s
server, which translates the names of websites into IP
addresses.
Domain A specific name for a network of computers.
Download To receive a file transmitted over a network.
DSL (Digital Subscriber Line) An always-on broadband
connection over traditional phone lines.
DSCP (DiffServ Code Point) Provides a method of
tagging IP packets with QoS priority information.
Dynamic IP Address A temporary IP address assigned by
a DHCP server.
EIGRP (Enhanced Interior Gateway Routing
Protocol) Provides fast convergence, support for variablelength subnet mask, and supports multiple network layer
protocols.
Encryption Encoding data transmitted in a network.
Ethernet IEEE standard network protocol that specifies
how data is placed on and retrieved from a common
transmission medium.
Firmware The programming code that runs a networking
device.
Flow Control Enables lower speed devices to
communicate with higher speed devices. This is
implemented by the higher speed device refraining from
sending packets.
FTP (File Transfer Protocol) A protocol used to transfer
files over a TCP/IP network.
Business Internet Video Camera with Audio
Glossary
Full Duplex The ability of a networking device to receive
and transmit data simultaneously.
GARP
(General
Attributes
Registration
Protocol) Registers client stations into a multicast
domain.
Gateway A device that interconnects networks with
different, incompatible communications protocols.
GBIC (GigaBit Interface Converter) A hardware module
used to attach network devices to fiber-based transmission
systems. GBIC converts the serial electrical signals to serial
optical signals and vice versa.
GVRP (GARP VLAN Registration Protocol) Registers
client stations into a VLANs.
Half Duplex Data transmission that can occur in two
directions over a single line, but only one direction at a
time.
HTTP
(HyperText
Transport
Protocol) The
communications protocol used to connect to servers on
the World Wide Web.
HTTPS (HyperText Transport Protocol Secure) An
extension to the standard HTTP protocol that provides
confidentiality by encrypting the traffic from the website.
By default this protocol uses TCP port 443.
ICMP (Internet Control Message Protocol) Allows the
gateway or destination host to communicate with the
source host. For example, to report a processing error.
IGMP (Internet Group Management Protocol) Allows
hosts to notify their local switch or router that they want
to receive transmissions assigned to a specific multicast
group.
IP (Internet Protocol) A protocol used to send data over
a network.
IP Address The address used to identify a computer or
device on a network.
IPCONFIG A Windows 2000 and XP utility that displays
the IP address for a particular networking device.
IPSec (Internet Protocol Security) A VPN protocol used
to implement secure exchange of packets at the IP layer.
ISP (Internet Service Provider) A company that provides
access to the Internet.
Jumbo Frames Enable transporting identical data in
fewer frames. Jumbo Frames reduce overhead, lower
processing time, and ensure fewer interrupts.
LAG (Link Aggregated Group) Aggregates ports or
VLANs into a single virtual port or VLAN.
LAN The computers and networking products that make
up your local network.
37
Appendix C
Glossary
MAC (Media Access Control) Address The unique
address that a manufacturer assigns to each networking
device.
RADIUS (Remote Authentication Dial-In User
Service) A protocol that uses an authentication server to
control network access.
Mask A filter that includes or excludes certain values, for
example parts of an IP address.
RJ-45 (Registered Jack-45) An Ethernet connector that
holds up to eight wires.
Mbps (MegaBits Per Second) One million bits per
second; a unit of measurement for data transmission.
RMON (Remote Monitoring) Provides
network
information to be collected from a single workstation.
MD5 (Message Digest 5) An algorithm that produces a
128-bit hash. MD5 is a variation of MD4, and increases MD4
security. MD5 verifies the integrity of the communication
and authenticates the origin of the communication.
Router A networking device that connects multiple
networks together.
MDI (Media Dependent Interface) A cable used for end
stations.
MDIX (Media Dependent Interface with Crossover) A
cable used for hubs and switches.
MIB (Management Information Base) MIBs contain
information describing specific aspects of network
components.
Multicast Transmits copies of a single packet to multiple
ports.
Network A series of computers or devices connected for
the purpose of data sharing, storage, and/or transmission
between users.
NMS (Network Management System) An interface that
provides a method of managing a system.
OID (Object Identifier) Used by SNMP to identify
managed objects. In the SNMP Manager/Agent network
management paradigm, each managed object must have
an OID to identify it.
Packet A unit of data sent over a network.
Ping (Packet INternet Groper) An Internet utility used
to determine whether a particular IP address is online.
Policing Determines if traffic levels are within a specified
profile. Policing manages the maximum traffic rate used
to send or receive packets on an interface.
Port The connection point on a computer or networking
device used for plugging in cables or adapters.
Port Mirroring Monitors and mirrors network traffic by
forwarding copies of incoming and outgoing packets
from one port to a monitoring port.
Power over Ethernet (PoE) A technology enabling an
Ethernet network cable to deliver both data and power.
QoS (Quality of Service) Provides policies that contain
sets of filters (rules). QoS allows network managers
to decide how and what network traffic is forwarded
according to priorities, application types, and source and
destination addresses.
Business Internet Video Camera with Audio
RSTP (Rapid Spanning Tree Protocol) Detects and uses
network topologies that allow a faster convergence of the
spanning tree, without creating forwarding loops.
Server Any computer whose function in a network is to
provide user access to files, printing, communications,
and other services.
SMTP (Simple Mail Transfer Protocol) The standard email protocol on the Internet.
SNMP (Simple Network Management Protocol) A
widely used network monitoring and control protocol.
SSH Secure Shell. A utility that uses strong authentication
and secure communications to log in to another computer
over a network.
SSL (Secure Socket Layer) Encryption technology for
the Internet used to provide secure transactions, such as
the transmission of credit card numbers for e-commerce.
Static IP Address A fixed address assigned to a computer
or device that is connected to a network.
STP (Spanning Tree Protocol) Prevents loops in network
traffic. The Spanning Tree Protocol (STP) provides tree
topography for any arrangement of bridges. STP provides
one path between end stations on a network, eliminating
loops.
Subnet (Sub-network) Subnets are portions of a
network that share a common address component. In
TCP/IP networks, devices that share a prefix are part of
the same subnet. For example, all devices with a prefix of
157.100.100.100 are part of the same subnet.
Subnet Mask An address code that determines the size
of the network.
Switch Filters and forwards packets between LAN
segments. Switches support any packet protocol type.
TACACS+ (Terminal Access Controller Access Control
System Plus) Proprietary Cisco enhancement to Terminal
Access Controller Access Control System (TACACS). Provides
additional support for authentication, authorization, and
accounting.
38
Appendix C
Glossary
TCP (Transmission Control Protocol) A network protocol
for transmitting data that requires acknowledgement
from the recipient of data sent.
TCP/IP (Transmission Control Protocol/Internet
Protocol) A set of instructions PCs use to communicate
over a network.
Telnet A user command and TCP/IP protocol used for
accessing remote PCs.
TFTP (Trivial File Transfer Protocol) A version of the
TCP/IP FTP protocol that has no directory or password
capability.
Throughput The amount of data moved successfully
from one node to another in a given time period.
Trunking Link Aggregation. Optimizes port usage by
linking a group of ports together to form a single trunk
(aggregated groups).
TX Rate Transmission Rate.
UDP (User Data Protocol) Communication protocol that
transmits packets but does not guarantee their delivery.
Upgrade To replace existing software or firmware with a
newer version.
Upload To transmit a file over a network.
URL (Uniform Resource Locator) The address of a file
located on the Internet.
VLAN (Virtual Local Area Networks) Logical subgroups
that constitute a Local Area Network (LAN). This is done in
software rather than defining a hardware solution.
WAN (Wide Area Network) Networks that cover a large
geographical area.
Wildcard Mask Specifies which IP address bits are
used, and which bits are ignored. A wild card mask
of 255.255.255.255 indicates that no bit is important.
A wildcard of 0.0.0.0 indicates that all the bits are
important.
For example, if the destination IP address is 149.36.184.198
and the wildcard mask is 255.36.184.00, the first two bits
of the IP address are used, while the last two bits are
ignored.
Business Internet Video Camera with Audio
39
Specifications
Appendix D
Appendix D:
Specifications
PVC2300 Specifications
Model
PVC2300
Standards
IEEE802.3, IEEE802.3u,
IEEE802.1p (QoS Priority),
IEEE802.1q (VLAN)
Protocols Supported
TCP/IP, HTTP, DHCP, SMTP, FTP,
NTP, DNS, UPnP, RTP, RTSP
and DDNS
Ports
Ethernet w/POE,
Microphone IN, Speaker OUT,
Power (12V, 1A), GPIO,
4-pin IRIS port
Buttons
Reset
Cabling Type
UTP CAT 5
LEDs
Power, Network
Camera Type
Box
IO ports
RS-485 x 1 (2 pins) Supports Pelco “D” protocol
commands
Input control x 2 (2 pins)
Output control x 2 (2 pins)
Management
Web Browser
Internet Explorer 5.x, or Above;
Netscape, Firefox
Event Logging
Event Logging (SYSLOG)
Web F/W upgrade
Firmware Upgradable Through
Web-Browser
Video Compression
Dual Codec
MPEG-4 Simple Profile
MJPEG
Simultaneous dual-stream
Snapshot
JPEG
Image Settings
Brightness and Contrast
Zoom
4x Digital Zoom
Night Vision
IR filter switcher for low light
Video Controls
Auto-White-Balance(AWB),
Auto-Exposure(AES)
Image Contol
Select video by Quality,
Bandwidth, and Frame Rate
Format
3GPP for use with 3G phones
Lens
Alerts
Sensor
1/4” Progressive CCD Sensor
Illumination
0.4LUX@F1.4
Motion Detection
4 Detection areas with
individual sensitivity
Lens type
CS Mount lens, fixed focus;
Adapter also included for
lenses that require more
distance between sensor and
lens
Email Alert
3 e-mail addresses
FTP uploading
FTP server address and login
settings
Instant Messaging
Jabber client support
Focal Length
500mm~Infinity
(for included lens)
Scheduled
Schedule by day or time
Field of View
60º (for included lens)
Triggers
Inputs 1, Input 2, Motion
Detection
Video Resolution
640x480 (VGA),
320x240 (QVGA),
160x120 (QQVGA)
Actions
Outputs 1, Output 2,
Messaging, E-mail, FTP
Frame Rate
1 to 30 fps (selectable)
Summary
2-Way Audio
Iris
Provides Iris control for
CS-mount auto-iris lens when
attached
Built-in Microphone
6mm, -40db + 3db
Microphone input
3.5 mm Phone jack
Speaker output
3.5 mm Phone jack
Setup/Config
WebUI
Built in Web UI for Easy
Browser-Based Configuration
(HTTP)
Business Internet Video Camera with Audio
Audio
Compression
G.726 - 16K, G.711 A-law and
µ-law
Sampling Rate
8 KHz
40
Specifications
Appendix D
Default Bit Rate
16Kbps
Management Utility
Monitoring and
Recording software
Monitoring and Recording for
up to 16 cameras
Advanced search histogram or
by time and date
Recording set up to record
by motion trigger, manual or
schedule recording and
playback
Security
User List
User Rights List to View Video
and/or to Camera Control
Functions
Username/password
Logon authentication 20
character username and
8 character password
Kensington lock
Physical security option
Network
RTP/RTSP
Real-Time Protocol, Real-Time
Streaming Protocol allow for
viewing from any client
supporting these protocols,
like 3G phones or Quicktime
client
NTP
Network Time Protocol keeps
time of camera in sync with
your network
SMTP
Simple Mail Transfer Protocol
Client allows video clips to be
e-mailed
FTP Client
FTP Client facilitates
scheduling transfer of images
to an FTP server
DDNS
Dynamic DNS facilitates
reaching the camera by a
name irrespective of camera’s
IP address. Supports DynDNS,
TZO, and 3322 Dynamic DNS
services
UPnP
Allows autodiscovery of the
camera by other UPnP devices
Power
Power Options
IEEE 802.3af Power over
Ethernet (PoE) - 48V/0.3A
External Power Adapter:
12V/1A, 110~120V AC/60Hz,
Switching
Power Consumption
10W
Environmental
Dimensions WxHxD
4.72" x 2.99" x 1.81"
(120 x 76 x 46 mm)
Unit Weight 1.15 lb (0.52 kg)
Power
External power adapter 12 VDC
1A 110~120VAC/60Hz
switching or POE 48V/0.3A
Certification
FCC part 15C class B, CE, UL,
EMC/EMI part 15B class B for
US
Operating Temp.
32 to 122ºF (0 to 50ºC)
Storage Temp.
-4 to 158ºF (-20 to 70ºC)
Operating Humidity
10% - 80%
Storage Humidity
0% - 90%
IP Filtering
Allow or disallow access by
IP address
Business Internet Video Camera with Audio
41
Specifications
Appendix D
WVC2300 Specifications
Model
WVC2300
Standards
IEEE802.11g, IEEE802.11b,
IEEE802.3, IEEE802.3u,
IEEE802.1p (QoS Priority),
IEEE802.1q (VLAN), 802.11e
(Wireless QoS)
Protocols Supported
TCP/IP, HTTP, DHCP, SMTP, FTP,
NTP, DNS, UPnP, RTP, RTSP and
DDNS
Ports
Ethernet, Microphone IN,
Speaker OUT, Power (12V, 1A),
GPIO, 4-pin IRIS port
Buttons
Reset
Cabling Type
UTP CAT 5
LEDs
Power, Network
Camera Type
Box
IO ports
RS-485 x 1 (2 pins) - Supports
Pelco “D” protocol commands
Input control x 2 (2 pins)
Firmware Upgradable Through
Web-Browser
Video Compression
Dual Codec
MPEG-4 Simple Profile
MJPEG
Simultaneous dual-stream
Snapshot
JPEG
Image Settings
Brightness and Contrast
Zoom
4x Digital Zoom
Night Vision
IR Cut filter for low light
Video Controls
Auto-White-Balance(AWB),
Auto-Exposure(AES)
Image Contol
Select video by Quality,
Bandwidth, and Frame Rate
Format
3GPP for use with 3G phones
Alerts
Motion Detection
4 Detection areas with
individual sensitivity
Email Alert
3 e-mail addresses
Output control x 2 (2 pins)
FTP uploading
FTP server address and login
settings
1/4” Progressive CCD Sensor
Instant Messaging
Jabber client support
Lens
Sensor
Web F/W upgrade
Illumination
0.4LUX@F1.4
Lens type
CS Mount lens, fixed focus;
Adapter also included for
lenses that require more
distance between sensor and
lens
Focal Length
500mm~Infinity
(for included lens)
Field of View
Scheduled
Schedule by day or time
Triggers
Inputs 1, Input 2, Motion
Detection
Actions
Outputs 1, Output 2,
Messaging, Email, FTP
Audio
Summary
2-Way Audio
60º (for included lens)
Built-in Microphone
6mm, -40db + 3db
Video Resolution
640x48 (VGA), 320x240 (QVGA),
160x120 (QQVGA)
Microphone input
3.5 mm Phone jack
Speaker output
3.5 mm Phone jack
Frame Rate
1 to 30 fps (selectable)
Iris
Provides Iris control for
CS-mount auto-iris lens when
attached
Compression
G.726 - 16K, G.711 A-law and
µ-law
Sampling Rate
8 KHz
Default Bit Rate
16Kbps
Setup/Config
WebUI
Built in Web UI for Easy
Browser-Based Configuration
(HTTP)
Management
Web Browser
Internet Explorer 5.x, or Above;
Netscape, Firefox
Event Logging
Event Logging (SYSLOG)
Business Internet Video Camera with Audio
42
Specifications
Appendix D
Management Utility
Power
Monitoring and
Recording software
Monitoring and Recording for
up to 16 cameras
Advanced search histogram or
by time and date
Recording set up to record
by motion trigger, manual or
schedule recording and
playback
Power Options
External Power Adapter:
12V/1A, 110~120V AC/60Hz,
Switching
Power Consumption
10W
Power
Security
Power Options
IEEE 802.3af Power over
Ethernet (PoE) - 48V/0.3A
External Power Adapter:
12V/1A, 110~120V AC/60Hz,
Switching
WEP/WPA
WEP 64bit/128bit, WPA-TKIP,
WPA-PSK
Power Consumption
Environmental
10W
User List
User Rights List to View Video
and/or to Camera Control
Functions
Dimensions WxHxD
4.72" x 2.99" x 1.81"
(120 x 76 x 46 mm)
Username/password
Logon authentication 20
character username and 8
character password
Unit Weight 1.15 lb (0.52 kg)
Kensington lock
Physical security option
Power
External power adapter 12 VDC
1A 110~120VAC/60Hz
switching
Certification
FCC part 15C class B, CE, UL,
EMC/EMI part 15B class B for
US
Operating Temp.
32 to 122ºF (0 to 50ºC)
Storage Temp.
-4 to 158ºF (-20 to 70ºC)
Operating Humidity
10% - 80%
Storage Humidity
0% - 90%
Network
RTP/RTSP
Real-Time Protocol, Real-Time
Streaming Protocol allow for
viewing from any client
supporting these protocols,
like 3G phones or Quicktime
client
NTP
Network Time Protocol keeps
time of camera in sync with
your network
SMTP
Simple Mail Transfer Protocol
Client allows video clips to be
e-mailed
FTP Client
FTP Client facilitates
scheduling transfer of images
to an FTP server
DDNS
Dynamic DNS facilitates
reaching the camera by a
name irrespective of camera’s
IP address. Supports DynDNS,
TZO, and 3322 Dynamic DNS
services
UPnP
Allows autodiscovery of the
camera by other UPnP devices
IP Filtering
Allow or disallow access by IP
address
Business Internet Video Camera with Audio
43
Specifications
Appendix D
I/O Port Specifications
10
9
8
7
6
5
4
3
2
1
I/O PIN Specifications
PIN
Function
Description
1
12VDC Output
With a maximum load of 100mA,
this output to be used with an
external device.
2
GND
3
Digital Input 1
Connect to high to activate
(5V-12V)
4
Digital Output 1
With a maximum load of 100mA
and maximum voltage of 12VDC,
this output has an open-collector
NPN transistor with the emitter
connected to GND.
5
Digital Input 2
Connect to high to activate
(5V-12V)
6
Digital Output 2
With a maximum load of 100mA
and maximum voltage of
12VDC,this output has an opencollector NPN transistor with the
emitter connected to GND.
7
GND
8
12VDC Output
With a maximum load of 100mA,
this output to be used with an
external device.
9
RS485-B
(Inverting)
A-half duplex RS485 inteface for
controlling auxiliary equipment
10
RS485-A
(non-Inverting)
Business Internet Video Camera with Audio
NOTE: The icons below can manually turn on or
off the output ports from the web-based utility’s
home page.
On This icon will turn on the selected output.
Off This icon turns off the selected output.
44
Appendix E
Appendix E:
Warranty Information
Limited Warranty
Linksys warrants to You that, for a period of one year
(the "Warranty Period"), your Linksys Product will be
substantially free of defects in materials and workmanship
under normal use. Your exclusive remedy and Linksys’
entire liability under this warranty will be for Linksys at
its option to repair or replace the Product or refund Your
purchase price less any rebates. This limited warranty
extends only to the original purchaser.
If the Product proves defective during the Warranty
Period call Linksys Technical Support in order to obtain
a Return Authorization Number, if applicable. BE SURE
TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN
CALLING. If You are requested to return the Product, mark
the Return Authorization Number clearly on the outside
of the package and include a copy of your original proof
of purchase. RETURN REQUESTS CANNOT BE PROCESSED
WITHOUT PROOF OF PURCHASE. You are responsible
for shipping defective Products to Linksys. Linksys pays
for UPS Ground shipping from Linksys back to You only.
Customers located outside of the United States of America
and Canada are responsible for all shipping and handling
charges.
Warranty Information
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT
WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE
THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING
OUT OF OR RELATED TO THE USE OF OR INABILITY TO
USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN
IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY
EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.
The foregoing limitations will apply even if any warranty or
remedy provided under this Agreement fails of its essential
purpose. Some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to You.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,
CA 92623.
ALL IMPLIED WARRANTIES AND CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO THE DURATION OF
THE WARRANTY PERIOD. ALL OTHER EXPRESS OR
IMPLIED
CONDITIONS,
REPRESENTATIONS
AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
NON‑INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions
do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to You. This
warranty gives You specific legal rights, and You may also
have other rights which vary by jurisdiction.
This warranty does not apply if the Product (a) has been
altered, except by Linksys, (b) has not been installed,
operated, repaired, or maintained in accordance with
instructions supplied by Linksys, or (c) has been subjected
to abnormal physical or electrical stress, misuse,
negligence, or accident. In addition, due to the continual
development of new techniques for intruding upon and
attacking networks, Linksys does not warrant that the
Product will be free of vulnerability to intrusion or attack.
Business Internet Video Camera with Audio
45
Appendix F
Wired Product Regulatory Information
Appendix F:
Wired Product
Regulatory Information
Industry Canada Statement
FCC Statement
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or
devices
•
Connect the equipment to an outlet other than the
receiver’s
•
Consult a dealer or an experienced radio/TV technician
for assistance
This device complies with Industry Canada ICES-003 rule.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including
interference that may cause undesired operation of
the device.
Avis d’Industrie Canada
Cet appareil est conforme à la norme NMB003 d’Industrie
Canada.
Le fonctionnement est soumis aux conditions suivantes :
1. Ce périphérique ne doit pas causer d’interférences;
2. Ce périphérique doit accepter toutes les interférences
reçues, y compris celles qui risquent d’entraîner un
fonctionnement indésirable.
Safety Notices
•
Caution: To reduce the risk of fire, use only No.26 AWG
or larger telecommunication line cord.
•
Do not use this product near water, for example, in a
wet basement or near a swimming pool.
•
Avoid using this product during an electrical storm.
There may be a remote risk of electric shock from
lightning.
WARNING: This product contains lead, known
to the State of California to cause cancer, and
birth defects or other reproductive harm. Wash
hands after handling.
Business Internet Video Camera with Audio
46
Appendix F
Wired Product Regulatory Information
User Information for Consumer Products
Covered by EU Directive 2002/96/EC on
Waste Electric and Electronic Equipment
(WEEE)
Ceština (Czech) - Informace o ochraně životního
prostředí pro zákazníky v zemích Evropské unie
This document contains important information for users
with regards to the proper disposal and recycling of
Linksys products. Consumers are required to comply with
this notice for all electronic products bearing the following
symbol:
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené
tímto symbolem na produktu anebo na obalu bylo likvidováno
s netříděným komunálním odpadem. Tento symbol udává,
že daný produkt musí být likvidován odděleně od běžného
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu
a dalších elektrických a elektronických zařízení prostřednictvím
určených sběrných míst stanovených vládou nebo místními
úřady. Správná likvidace a recyklace pomáhá předcházet
potenciálním negativním dopadům na životní prostředí a lidské
zdraví. Podrobnější informace o likvidaci starého vybavení si
laskavě vyžádejte od místních úřadů, podniku zabývajícího se
likvidací komunálních odpadů nebo obchodu, kde jste produkt
zakoupili.
Dansk (Danish) - Miljøinformation for kunder i EU
English - Environmental Information for Customers in
the European Union
European Directive 2002/96/EC requires that the equipment
bearing this symbol on the product and/or its packaging must
not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately
from regular household waste streams. It is your responsibility to
dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or
local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and
human health. For more detailed information about the disposal
of your old equipment, please contact your local authorities,
waste disposal service, or the shop where you purchased the
product.
Български (Bulgarian) - Информация относно
опазването на околната среда за потребители в
Европейския съюз
Европейска директива 2002/96/EC изисква уредите, носещи
този символ върху изделието и/или опаковката му, да не
се изхвърля т с несортирани битови отпадъци. Символът
обозначава, че изделието трябва да се изхвърля отделно от
сметосъбирането на обикновените битови отпадъци. Ваша
е отговорността този и другите електрически и електронни
уреди да се изхвърлят в предварително определени от
държавните или общински органи специализирани пунктове
за събиране. Правилното изхвърляне и рециклиране
ще спомогнат да се предотвратят евентуални вредни за
околната среда и здравето на населението последствия. За
по-подробна информация относно изхвърлянето на вашите
стари уреди се обърнете към местните власти, службите за
сметосъбиране или магазина, от който сте закупили уреда.
Business Internet Video Camera with Audio
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
på produktet og/eller emballagen ikke må bortskaffes som
usorteret kommunalt affald. Symbolet betyder, at dette produkt
skal bortskaffes adskilt fra det almindelige husholdningsaffald.
Det er dit ansvar at bortskaffe dette og andet elektrisk og
elektronisk udstyr via bestemte indsamlingssteder udpeget
af staten eller de lokale myndigheder. Korrekt bortskaffelse
og genvinding vil hjælpe med til at undgå mulige skader for
miljøet og menneskers sundhed. Kontakt venligst de lokale
myndigheder, renovationstjenesten eller den butik, hvor du
har købt produktet, angående mere detaljeret information om
bortskaffelse af dit gamle udstyr.
Deutsch (German) - Umweltinformation für Kunden
innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit
diesem Symbol versehen ist , nicht zusammen mit unsortiertem
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf
hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses
Gerät und andere elektrische und elektronische Geräte über
die dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an
die örtlichen Behörden oder städtischen Entsorgungsdienste
oder an den Händler, bei dem Sie das Produkt erworben haben.
47
Appendix F
Wired Product Regulatory Information
Eesti (Estonian) - Keskkonnaalane informatsioon
Euroopa Liidus asuvatele klientidele
Français (French) - Informations environnementales
pour les clients de l’Union européenne
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on
seadmeid, millel on tootel või pakendil käesolev sümbol ,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike
ametiasutuste poolt ette nähtud kogumispunktide kaudu.
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste
tervisele. Vanade seadmete kõrvaldamise kohta täpsema
informatsiooni saamiseks võtke palun ühendust kohalike
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te
toote ostsite.
La directive européenne 2002/96/CE exige que l’équipement
sur lequel est apposé ce symbole sur le produit et/ou son
emballage ne soit pas jeté avec les autres ordures ménagères. Ce
symbole indique que le produit doit être éliminé dans un circuit
distinct de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre matériel
électrique ou électronique par les moyens de collecte indiqués
par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme
ont pour but de lutter contre l’impact néfaste potentiel de ce
type de produits sur l’environnement et la santé publique. Pour
plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics
locaux, le service de traitement des déchets, ou l’endroit où vous
avez acheté le produit.
Español (Spanish) - Información medioambiental para
clientes de la Unión Europea
La Directiva 2002/96/CE de la UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su embalaje
no deben eliminarse junto con otros residuos urbanos no
seleccionados. El símbolo indica que el producto en cuestión
debe separarse de los residuos domésticos convencionales con
vistas a su eliminación. Es responsabilidad suya desechar este y
cualesquiera otros aparatos eléctricos y electrónicos a través de
los puntos de recogida que ponen a su disposición el gobierno y
las autoridades locales. Al desechar y reciclar correctamente estos
aparatos estará contribuyendo a evitar posibles consecuencias
negativas para el medio ambiente y la salud de las personas. Si
desea obtener información más detallada sobre la eliminación
segura de su aparato usado, consulte a las autoridades locales,
al servicio de recogida y eliminación de residuos de su zona o
pregunte en la tienda donde adquirió el producto.
ξλληνικά (Greek) - Στοιχεία περιβαλλοντικής
προστασίας για πελάτες εντός της Ευρωπαϊκής
Ένωσης
Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίος
φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία
του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι
οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές.
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη
πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία.
Για περισσότερες πληροφορίες σχετικά με την απόρριψη του
παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές
αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο
αγοράσατε το προϊόν.
Business Internet Video Camera with Audio
Italiano (Italian) - Informazioni relative all’ambiente
per i clienti residenti nell’Unione Europea
La direttiva europea 2002/96/EC richiede che le apparecchiature
contrassegnate con questo simbolo
sul prodotto e/o
sull’imballaggio non siano smaltite insieme ai rifiuti urbani
non differenziati. Il simbolo indica che questo prodotto non
deve essere smaltito insieme ai normali rifiuti domestici. È
responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante
le specifiche strutture di raccolta indicate dal governo o dagli
enti pubblici locali. Il corretto smaltimento ed il riciclaggio
aiuteranno a prevenire conseguenze potenzialmente negative
per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli
enti pubblici di competenza, il servizio di smaltimento rifiuti o il
negozio nel quale avete acquistato il prodotto.
Latviešu valoda (Latvian) - Ekoloģiska informācija
klientiem Eiropas Savienības jurisdikcijā
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo
un citas elektriskas un elektroniskas ierīces izmest atkritumos,
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,
kur iegādājāties šo izstrādājumu.
48
Appendix F
Wired Product Regulatory Information
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,
skirta Europos Sąjungos vartotojams
Nederlands (Dutch) - Milieu-informatie voor klanten
in de Europese Unie
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),
negalima šalinti kartu su nerūšiuotomis komunalinėmis
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose
įsigijote tą gaminį.
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die
is voorzien van dit symbool op het product of de verpakking,
niet mag worden ingezameld met niet-gescheiden huishoudelijk
afval. Dit symbool geeft aan dat het product apart moet worden
ingezameld. U bent zelf verantwoordelijk voor de vernietiging
van deze en andere elektrische en elektronische apparatuur via de
daarvoor door de landelijke of plaatselijke overheid aangewezen
inzamelingskanalen. De juiste vernietiging en recycling van
deze apparatuur voorkomt mogelijke negatieve gevolgen voor
het milieu en de gezondheid. Voor meer informatie over het
vernietigen van uw oude apparatuur neemt u contact op met
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de
winkel waar u het product hebt aangeschaft.
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti
fl-Unjoni Ewropea
Norsk (Norwegian) - Miljøinformasjon for kunder i EU
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih issimbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema
ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika
li dan il-prodott għandu jintrema separatament minn ma’ liskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew
il-ħanut minn fejn xtrajt il-prodott.
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
avbildet på produktet og/eller pakningen, ikke må kastes
sammen med usortert avfall. Symbolet indikerer at dette
produktet skal håndteres atskilt fra ordinær avfallsinnsamling
for husholdningsavfall. Det er ditt ansvar å kvitte deg med
dette produktet og annet elektrisk og elektronisk avfall via egne
innsamlingsordninger slik myndighetene eller kommunene
bestemmer. Korrekt avfallshåndtering og gjenvinning vil
være med på å forhindre mulige negative konsekvenser for
miljø og helse. For nærmere informasjon om håndtering av
det kasserte utstyret ditt, kan du ta kontakt med kommunen,
en innsamlingsstasjon for avfall eller butikken der du kjøpte
produktet.
Magyar (Hungarian) - Környezetvédelmi információ az
európai uniós vásárlók számára
Polski (Polish) - Informacja dla klientów w Unii
Europejskiej o przepisach dotyczących ochrony
środowiska
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy
azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán
az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott
termék kidobásakor a szokványos háztartási hulladékelszállítási
rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön
felelõssége, hogy ezt, és más elektromos és elektronikus
berendezéseit a kormányzati vagy a helyi hatóságok által
kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ
hulladékfeldolgozás segít a környezetre és az emberi egészségre
potenciálisan ártalmas negatív hatások megelõzésében. Ha
elavult berendezéseinek felszámolásához további részletes
információra van szüksége, kérjük, lépjen kapcsolatba a helyi
hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal
üzlettel, ahol a terméket vásárolta.
Business Internet Video Camera with Audio
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt
oznaczony symbolem znajdującym się na produkcie i/lub jego
opakowaniu nie był wyrzucany razem z innymi niesortowanymi
odpadami komunalnymi. Symbol ten wskazuje, że produkt
nie powinien być usuwany razem ze zwykłymi odpadami z
gospodarstw domowych. Na Państwu spoczywa obowiązek
wyrzucania tego i innych urządzeń elektrycznych oraz
elektronicznych w punktach odbioru wyznaczonych przez władze
krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób
i jego recykling pomogą zapobiec potencjalnie negatywnym
konsekwencjom dla środowiska i zdrowia ludzkiego. W celu
uzyskania szczegółowych informacji o usuwaniu starego sprzętu,
prosimy zwrócić się do lokalnych władz, służb oczyszczania
miasta lub sklepu, w którym produkt został nabyty.
49
Appendix F
Wired Product Regulatory Information
Português (Portuguese) - Informação ambiental para
clientes da União Europeia
Slovenčina (Slovene) - Okoljske informacije za stranke
v Evropski uniji
A Directiva Europeia 2002/96/CE exige que o equipamento
que exibe este símbolo no produto e/ou na sua embalagem
não seja eliminado junto com os resíduos municipais não
separados. O símbolo indica que este produto deve ser
eliminado separadamente dos resíduos domésticos regulares.
É da sua responsabilidade eliminar este e qualquer outro
equipamento eléctrico e electrónico através das instalações
de recolha designadas pelas autoridades governamentais ou
locais. A eliminação e reciclagem correctas ajudarão a prevenir
as consequências negativas para o ambiente e para a saúde
humana. Para obter informações mais detalhadas sobre a
forma de eliminar o seu equipamento antigo, contacte as
autoridades locais, os serviços de eliminação de resíduos ou o
estabelecimento comercial onde adquiriu o produto.
Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme,
označene s tem simbolom – na izdelku in/ali na embalaži – med
običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba
izdelek odvreči ločeno od preostalih gospodinjskih odpadkov.
Vaša odgovornost je, da to in preostalo električno in elektronsko
opremo odnesete na posebna zbirališča, ki jih določijo
državne ustanove ali lokalna uprava. S pravilnim odlaganjem
in recikliranjem boste preprečili morebitne škodljive vplive na
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare
opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer
ste izdelek kupili.
Română (Romanian) - Informaţii de mediu pentru
clienţii din Uniunea Europeană
Directiva europeană 2002/96/CE impune ca echipamentele care
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să
nu fie casate împreună cu gunoiul menajer municipal. Simbolul
indică faptul că acest produs trebuie să fie casat separat de
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi
acest produs şi alte echipamente electrice şi electronice prin
intermediul unităţilor de colectare special desemnate de guvern
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta
la prevenirea potenţialelor consecinţe negative asupra sănătăţii
mediului şi a oamenilor. Pentru mai multe informaţii detaliate
cu privire la casarea acestui echipament vechi, contactaţi
autorităţile locale, serviciul de salubrizare sau magazinul de la
care aţi achiziţionat produsul.
Slovenčina (Slovak) - Informácie o ochrane životného
prostredia pre zákazníkov v Európskej únii
Podľa európskej smernice 2002/96/ES zariadenie s týmto
symbolom
na produkte a/alebo jeho balení nesmie byť
likvidované spolu s netriedeným komunálnym odpadom.
Symbol znamená, že produkt by sa mal likvidovať oddelene
od bežného odpadu z domácností. Je vašou povinnosťou
likvidovať toto i ostatné elektrické a elektronické zariadenia
prostredníctvom špecializovaných zberných zariadení určených
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia
pomôže zabrániť prípadným negatívnym dopadom na životné
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov
alebo obchod, v ktorom ste si produkt zakúpili.
Business Internet Video Camera with Audio
Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä
symboli
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet
viemällä tuote tai tuotteet viranomaisten määräämään
keräyspisteeseen. Laitteiston oikea hävittäminen estää
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä
myymälästä, josta ostit tuotteen.
Svenska (Swedish) - Miljöinformation för kunder i
Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med
denna symbol på produkten och/eller förpackningen inte får
kastas med osorterat kommunalt avfall. Symbolen visar att denna
produkt bör kastas efter att den avskiljts från vanligt hushållsavfall.
Det faller på ditt ansvar att kasta denna och annan elektrisk och
elektronisk utrustning på fastställda insamlingsplatser utsedda
av regeringen eller lokala myndigheter. Korrekt kassering och
återvinning skyddar mot eventuella negativa konsekvenser
för miljön och personhälsa. För mer detaljerad information om
kassering av din gamla utrustning kontaktar du dina lokala
myndigheter, avfallshanteringen eller butiken där du köpte
produkten.
WEB: For additional information, please visit
www.linksys.com
50
Appendix G
Wireless Product Regulatory Information
Appendix G:
Wireless Product
Regulatory Information
Safety Notices
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or
devices
•
Connect the equipment to an outlet other than the
receiver’s
•
Consult a dealer or an experienced radio/TV technician
for assistance
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator and your
body.
•
Caution: To reduce the risk of fire, use only No.26 AWG
or larger telecommunication line cord.
•
Do not use this product near water, for example, in a
wet basement or near a swimming pool.
•
Avoid using this product during an electrical storm.
There may be a remote risk of electric shock from
lightning.
WARNING: This product contains lead, known
to the State of California to cause cancer, and
birth defects or other reproductive harm. Wash
hands after handling.
Industry Canada Statement
This device complies with Industry Canada ICES-003 and
RSS210 rules.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device. This device has been designed to operate with
an antenna having a maximum gain of 2dBi. Antenna
having a higher gain is strictly prohibited per regulations
of Industry Canada. The required antenna impedance
is 50 ohms. To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the EIRP is not more than required for successful
communication.
Industry Canada Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. IEEE
802.11b or 802.11g operation of this product in the USA is
firmware-limited to channels 1 through 11.
Business Internet Video Camera with Audio
51
Appendix G
Wireless Product Regulatory Information
Avis d’Industrie Canada
Avis de non-responsabilité concernant les
appareils sans fil
Cet appareil est conforme aux normes NMB003 et RSS210
d’Industrie Canada.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes :
1. il ne doit pas produire de brouillage et
2. il doit accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre
le fonctionnement du dispositif. Le dispositif a été
conçu pour fonctionner avec une antenne ayant un gain
maximum de 2 dBi. Les règlements d’Industrie Canada
interdisent strictement l’utilisation d’antennes dont le
gain est supérieur à cette limite. L’impédance requise
de l’antenne est de 50 ohms. Afin de réduire le risque d’interférence aux autres
utilisateurs, le type d’antenne et son gain doivent
être choisis de façon à ce que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne soit pas supérieure
au niveau requis pour obtenir une communication
satisfaisante.
Les performances maximales pour les réseaux sans fil
sont tirées des spécifications de la norme IEEE 802.11.
Les performances réelles peuvent varier, notamment
en fonction de la capacité du réseau sans fil, du débit
de la transmission de données, de la portée et de la
couverture. Les performances dépendent de facteurs,
conditions et variables multiples, en particulier de la
distance par rapport au point d’accès, du volume du trafic
réseau, des matériaux utilisés dans le bâtiment et du
type de construction, du système d’exploitation et de la
combinaison de produits sans fil utilisés, des interférences
et de toute autre condition défavorable.
Avis d’Industrie Canada concernant l’exposition
aux radiofréquences :
Ce matériel est conforme aux limites établies par IC
en matière d’exposition aux radiofréquences dans un
environnement non contrôlé. Ce matériel doit être installé
et utilisé à une distance d’au moins 20 cm entre l’antenne
et le corps de l’utilisateur.
L’émetteur ne doit pas être placé près d’une autre antenne
ou d’un autre émetteur, ou fonctionner avec une autre
antenne ou un autre émetteur.
Wireless Disclaimer
The maximum performance for wireless is derived from
IEEE Standard 802.11 specifications. Actual performance
can vary, including lower wireless network capacity,
data throughput rate, range and coverage. Performance
depends on many factors, conditions and variables,
including distance from the access point, volume of
network traffic, building materials and construction,
operating system used, mix of wireless products used,
interference and other adverse conditions.
Business Internet Video Camera with Audio
52
Appendix G
User Information for Consumer Products
Covered by EU Directive 2002/96/EC on
Waste Electric and Electronic Equipment
(WEEE)
This document contains important information for users
with regards to the proper disposal and recycling of
Linksys products. Consumers are required to comply with
this notice for all electronic products bearing the following
symbol:
Wireless Product Regulatory Information
Ceština (Czech) - Informace o ochraně životního
prostředí pro zákazníky v zemích Evropské unie
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené
tímto symbolem na produktu anebo na obalu bylo likvidováno
s netříděným komunálním odpadem. Tento symbol udává,
že daný produkt musí být likvidován odděleně od běžného
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu
a dalších elektrických a elektronických zařízení prostřednictvím
určených sběrných míst stanovených vládou nebo místními
úřady. Správná likvidace a recyklace pomáhá předcházet
potenciálním negativním dopadům na životní prostředí a lidské
zdraví. Podrobnější informace o likvidaci starého vybavení si
laskavě vyžádejte od místních úřadů, podniku zabývajícího se
likvidací komunálních odpadů nebo obchodu, kde jste produkt
zakoupili.
Dansk (Danish) - Miljøinformation for kunder i EU
English - Environmental Information for Customers in
the European Union
European Directive 2002/96/EC requires that the equipment
bearing this symbol on the product and/or its packaging must
not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately
from regular household waste streams. It is your responsibility to
dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or
local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and
human health. For more detailed information about the disposal
of your old equipment, please contact your local authorities,
waste disposal service, or the shop where you purchased the
product.
Български (Bulgarian) - Информация относно
опазването на околната среда за потребители в
Европейския съюз
Европейска директива 2002/96/EC изисква уредите, носещи
този символ върху изделието и/или опаковката му, да не
се изхвърля т с несортирани битови отпадъци. Символът
обозначава, че изделието трябва да се изхвърля отделно от
сметосъбирането на обикновените битови отпадъци. Ваша
е отговорността този и другите електрически и електронни
уреди да се изхвърлят в предварително определени от
държавните или общински органи специализирани пунктове
за събиране. Правилното изхвърляне и рециклиране
ще спомогнат да се предотвратят евентуални вредни за
околната среда и здравето на населението последствия. За
по-подробна информация относно изхвърлянето на вашите
стари уреди се обърнете към местните власти, службите за
сметосъбиране или магазина, от който сте закупили уреда.
Business Internet Video Camera with Audio
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
på produktet og/eller emballagen ikke må bortskaffes som
usorteret kommunalt affald. Symbolet betyder, at dette produkt
skal bortskaffes adskilt fra det almindelige husholdningsaffald.
Det er dit ansvar at bortskaffe dette og andet elektrisk og
elektronisk udstyr via bestemte indsamlingssteder udpeget
af staten eller de lokale myndigheder. Korrekt bortskaffelse
og genvinding vil hjælpe med til at undgå mulige skader for
miljøet og menneskers sundhed. Kontakt venligst de lokale
myndigheder, renovationstjenesten eller den butik, hvor du
har købt produktet, angående mere detaljeret information om
bortskaffelse af dit gamle udstyr.
Deutsch (German) - Umweltinformation für Kunden
innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit
diesem Symbol versehen ist , nicht zusammen mit unsortiertem
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf
hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses
Gerät und andere elektrische und elektronische Geräte über
die dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an
die örtlichen Behörden oder städtischen Entsorgungsdienste
oder an den Händler, bei dem Sie das Produkt erworben haben.
53
Appendix G
Wireless Product Regulatory Information
Eesti (Estonian) - Keskkonnaalane informatsioon
Euroopa Liidus asuvatele klientidele
Français (French) - Informations environnementales
pour les clients de l’Union européenne
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on
seadmeid, millel on tootel või pakendil käesolev sümbol ,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike
ametiasutuste poolt ette nähtud kogumispunktide kaudu.
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste
tervisele. Vanade seadmete kõrvaldamise kohta täpsema
informatsiooni saamiseks võtke palun ühendust kohalike
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te
toote ostsite.
La directive européenne 2002/96/CE exige que l’équipement
sur lequel est apposé ce symbole sur le produit et/ou son
emballage ne soit pas jeté avec les autres ordures ménagères. Ce
symbole indique que le produit doit être éliminé dans un circuit
distinct de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre matériel
électrique ou électronique par les moyens de collecte indiqués
par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme
ont pour but de lutter contre l’impact néfaste potentiel de ce
type de produits sur l’environnement et la santé publique. Pour
plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics
locaux, le service de traitement des déchets, ou l’endroit où vous
avez acheté le produit.
Español (Spanish) - Información medioambiental para
clientes de la Unión Europea
La Directiva 2002/96/CE de la UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su embalaje
no deben eliminarse junto con otros residuos urbanos no
seleccionados. El símbolo indica que el producto en cuestión
debe separarse de los residuos domésticos convencionales con
vistas a su eliminación. Es responsabilidad suya desechar este y
cualesquiera otros aparatos eléctricos y electrónicos a través de
los puntos de recogida que ponen a su disposición el gobierno y
las autoridades locales. Al desechar y reciclar correctamente estos
aparatos estará contribuyendo a evitar posibles consecuencias
negativas para el medio ambiente y la salud de las personas. Si
desea obtener información más detallada sobre la eliminación
segura de su aparato usado, consulte a las autoridades locales,
al servicio de recogida y eliminación de residuos de su zona o
pregunte en la tienda donde adquirió el producto.
ξλληνικά (Greek) - Στοιχεία περιβαλλοντικής
προστασίας για πελάτες εντός της Ευρωπαϊκής
Ένωσης
Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίος
φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία
του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι
οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές.
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη
πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία.
Για περισσότερες πληροφορίες σχετικά με την απόρριψη του
παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές
αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο
αγοράσατε το προϊόν.
Business Internet Video Camera with Audio
Italiano (Italian) - Informazioni relative all’ambiente
per i clienti residenti nell’Unione Europea
La direttiva europea 2002/96/EC richiede che le apparecchiature
contrassegnate con questo simbolo
sul prodotto e/o
sull’imballaggio non siano smaltite insieme ai rifiuti urbani
non differenziati. Il simbolo indica che questo prodotto non
deve essere smaltito insieme ai normali rifiuti domestici. È
responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante
le specifiche strutture di raccolta indicate dal governo o dagli
enti pubblici locali. Il corretto smaltimento ed il riciclaggio
aiuteranno a prevenire conseguenze potenzialmente negative
per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli
enti pubblici di competenza, il servizio di smaltimento rifiuti o il
negozio nel quale avete acquistato il prodotto.
Latviešu valoda (Latvian) - Ekoloģiska informācija
klientiem Eiropas Savienības jurisdikcijā
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo
un citas elektriskas un elektroniskas ierīces izmest atkritumos,
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,
kur iegādājāties šo izstrādājumu.
54
Appendix G
Wireless Product Regulatory Information
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,
skirta Europos Sąjungos vartotojams
Nederlands (Dutch) - Milieu-informatie voor klanten
in de Europese Unie
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),
negalima šalinti kartu su nerūšiuotomis komunalinėmis
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose
įsigijote tą gaminį.
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die
is voorzien van dit symbool op het product of de verpakking,
niet mag worden ingezameld met niet-gescheiden huishoudelijk
afval. Dit symbool geeft aan dat het product apart moet worden
ingezameld. U bent zelf verantwoordelijk voor de vernietiging
van deze en andere elektrische en elektronische apparatuur via de
daarvoor door de landelijke of plaatselijke overheid aangewezen
inzamelingskanalen. De juiste vernietiging en recycling van
deze apparatuur voorkomt mogelijke negatieve gevolgen voor
het milieu en de gezondheid. Voor meer informatie over het
vernietigen van uw oude apparatuur neemt u contact op met
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de
winkel waar u het product hebt aangeschaft.
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti
fl-Unjoni Ewropea
Norsk (Norwegian) - Miljøinformasjon for kunder i EU
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih issimbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema
ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika
li dan il-prodott għandu jintrema separatament minn ma’ liskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew
il-ħanut minn fejn xtrajt il-prodott.
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
avbildet på produktet og/eller pakningen, ikke må kastes
sammen med usortert avfall. Symbolet indikerer at dette
produktet skal håndteres atskilt fra ordinær avfallsinnsamling
for husholdningsavfall. Det er ditt ansvar å kvitte deg med
dette produktet og annet elektrisk og elektronisk avfall via egne
innsamlingsordninger slik myndighetene eller kommunene
bestemmer. Korrekt avfallshåndtering og gjenvinning vil
være med på å forhindre mulige negative konsekvenser for
miljø og helse. For nærmere informasjon om håndtering av
det kasserte utstyret ditt, kan du ta kontakt med kommunen,
en innsamlingsstasjon for avfall eller butikken der du kjøpte
produktet.
Magyar (Hungarian) - Környezetvédelmi információ az
európai uniós vásárlók számára
Polski (Polish) - Informacja dla klientów w Unii
Europejskiej o przepisach dotyczących ochrony
środowiska
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy
azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán
az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott
termék kidobásakor a szokványos háztartási hulladékelszállítási
rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön
felelõssége, hogy ezt, és más elektromos és elektronikus
berendezéseit a kormányzati vagy a helyi hatóságok által
kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ
hulladékfeldolgozás segít a környezetre és az emberi egészségre
potenciálisan ártalmas negatív hatások megelõzésében. Ha
elavult berendezéseinek felszámolásához további részletes
információra van szüksége, kérjük, lépjen kapcsolatba a helyi
hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal
üzlettel, ahol a terméket vásárolta.
Business Internet Video Camera with Audio
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt
oznaczony symbolem znajdującym się na produkcie i/lub jego
opakowaniu nie był wyrzucany razem z innymi niesortowanymi
odpadami komunalnymi. Symbol ten wskazuje, że produkt
nie powinien być usuwany razem ze zwykłymi odpadami z
gospodarstw domowych. Na Państwu spoczywa obowiązek
wyrzucania tego i innych urządzeń elektrycznych oraz
elektronicznych w punktach odbioru wyznaczonych przez władze
krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób
i jego recykling pomogą zapobiec potencjalnie negatywnym
konsekwencjom dla środowiska i zdrowia ludzkiego. W celu
uzyskania szczegółowych informacji o usuwaniu starego sprzętu,
prosimy zwrócić się do lokalnych władz, służb oczyszczania
miasta lub sklepu, w którym produkt został nabyty.
55
Appendix G
Wireless Product Regulatory Information
Português (Portuguese) - Informação ambiental para
clientes da União Europeia
Slovenčina (Slovene) - Okoljske informacije za stranke
v Evropski uniji
A Directiva Europeia 2002/96/CE exige que o equipamento
que exibe este símbolo no produto e/ou na sua embalagem
não seja eliminado junto com os resíduos municipais não
separados. O símbolo indica que este produto deve ser
eliminado separadamente dos resíduos domésticos regulares.
É da sua responsabilidade eliminar este e qualquer outro
equipamento eléctrico e electrónico através das instalações
de recolha designadas pelas autoridades governamentais ou
locais. A eliminação e reciclagem correctas ajudarão a prevenir
as consequências negativas para o ambiente e para a saúde
humana. Para obter informações mais detalhadas sobre a
forma de eliminar o seu equipamento antigo, contacte as
autoridades locais, os serviços de eliminação de resíduos ou o
estabelecimento comercial onde adquiriu o produto.
Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme,
označene s tem simbolom – na izdelku in/ali na embalaži – med
običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba
izdelek odvreči ločeno od preostalih gospodinjskih odpadkov.
Vaša odgovornost je, da to in preostalo električno in elektronsko
opremo odnesete na posebna zbirališča, ki jih določijo
državne ustanove ali lokalna uprava. S pravilnim odlaganjem
in recikliranjem boste preprečili morebitne škodljive vplive na
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare
opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer
ste izdelek kupili.
Română (Romanian) - Informaţii de mediu pentru
clienţii din Uniunea Europeană
Directiva europeană 2002/96/CE impune ca echipamentele care
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să
nu fie casate împreună cu gunoiul menajer municipal. Simbolul
indică faptul că acest produs trebuie să fie casat separat de
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi
acest produs şi alte echipamente electrice şi electronice prin
intermediul unităţilor de colectare special desemnate de guvern
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta
la prevenirea potenţialelor consecinţe negative asupra sănătăţii
mediului şi a oamenilor. Pentru mai multe informaţii detaliate
cu privire la casarea acestui echipament vechi, contactaţi
autorităţile locale, serviciul de salubrizare sau magazinul de la
care aţi achiziţionat produsul.
Slovenčina (Slovak) - Informácie o ochrane životného
prostredia pre zákazníkov v Európskej únii
Podľa európskej smernice 2002/96/ES zariadenie s týmto
symbolom
na produkte a/alebo jeho balení nesmie byť
likvidované spolu s netriedeným komunálnym odpadom.
Symbol znamená, že produkt by sa mal likvidovať oddelene
od bežného odpadu z domácností. Je vašou povinnosťou
likvidovať toto i ostatné elektrické a elektronické zariadenia
prostredníctvom špecializovaných zberných zariadení určených
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia
pomôže zabrániť prípadným negatívnym dopadom na životné
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov
alebo obchod, v ktorom ste si produkt zakúpili.
Business Internet Video Camera with Audio
Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä
symboli
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet
viemällä tuote tai tuotteet viranomaisten määräämään
keräyspisteeseen. Laitteiston oikea hävittäminen estää
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä
myymälästä, josta ostit tuotteen.
Svenska (Swedish) - Miljöinformation för kunder i
Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med
denna symbol på produkten och/eller förpackningen inte får
kastas med osorterat kommunalt avfall. Symbolen visar att denna
produkt bör kastas efter att den avskiljts från vanligt hushållsavfall.
Det faller på ditt ansvar att kasta denna och annan elektrisk och
elektronisk utrustning på fastställda insamlingsplatser utsedda
av regeringen eller lokala myndigheter. Korrekt kassering och
återvinning skyddar mot eventuella negativa konsekvenser
för miljön och personhälsa. För mer detaljerad information om
kassering av din gamla utrustning kontaktar du dina lokala
myndigheter, avfallshanteringen eller butiken där du köpte
produkten.
WEB: For additional information, please visit
www.linksys.com
56
Appendix H
Contact Information
Appendix H:
Contact Information
Linksys Contact Information
Website
http://www.linksys.com
E-Mail
support@linksys.com
FTP Site
ftp.linksys.com
Advice Line
800-546-5797 (LINKSYS)
Support
800-326-7114
RMA (Return Merchandise
949-823-3000
Authorization)
Fax
949-823-3002
NOTE: Details on warranty and RMA issues
can be found in the Warranty and Regulatory
Information section of this Guide.
7081510NC-RR
Business Internet Video Camera with Audio
57