Amypower Alltrack R Owner`s manual

Part Number: G-0017
OWNER’S MANUAL
ALLTRACK R3 & R Series Power Wheelchair
Supplier: This manual must be given to this wheelchair user.
User: Before using this wheelchair, please read this entire manual and save it for future reference.
I. INTRODUCTION
AMYPOWER LISTENS
USER WARNING
Thank you for choosing an Amypower wheelchair. We
want to hear your questions or comments about this
manual, the safety and reliability of your chair, and the
service you receive from your Amypower supplier. Please
feel free to write or call us at the address and telephone
number below:
WARNING
Attention wheelchair users do not operate this wheelchair
without first reading the owner’s manual. If you do not
understand the instructions and warnings of this owner’s
manual please contact your dealer or qualified technician
before operating this Amypower wheelchair. Failure to do
so may result in damage and/or injury.
AMYPOWER
Customer Service Department
USA
178 West Service Road
Champlain, NY, 12919
Canada
1650 Chicoine
Vaudreuil-Dorion, QC, J7V 8P2
Phone: 1-888-453-0311
Fax: 1-877-501-8458
service@Amypower.com
techservice@Amypower.com
FOR ANSWERS TO YOUR QUESTIONS
Your authorized supplier knows your wheelchair best,
and can answer most of your questions about chair
safety, use and maintenance. For future reference, fill
in the following:
DEALER/TECHNICIAN WARNING
WARNING
Attention dealers and qualified technicians do not operate
or service this wheelchair without first reading this owner’s
manual. If you do not understand the instructions and
warnings of this owner’s manual please contact the
Amypower Technical Service Department before operating
and/or servicing this Amypower wheelchair. Failure to do
so may result in damage and/or injury.
WARNING
In addition, power wheelchairs may contain printed
circuit boards. Careful attention should be given to the
Printed Circuit Board Handling Techniques insert
supplied with the chair.
Related Documents
Listed below are additional documents which are referenced in this owner’s manual.

PG Drives:
Supplier:
Sales Person:
Address:
Telephone:
R-Net module user information sheet
R-Net power module user information sheet
R-Net intelligent lighting/seating module
R-Net input output module
R-Net on-board programming manual
R-Net Omni technical manual
VR2 wheelchair control system
VR2 attendant module
PPIA programming and diagnostics
Fax:
Serial #:
Date/Purchased:
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
2
TABLE OF CONTENT
I.. INTRODUCTION ...........................................................
II. TABLE OF CONTENTS ......................................................
III. YOUR CHAIR AND ITS PARTS ............................................
IV. NOTICE - READ BEFORE USE .............................................
V. EMI (ELECTROMAGNETIC INTERFERENCE)...................
A. What is EMI..................................................................................
B. What Effect Can EMI Have ........................................................
C. Sources of EMI ...........................................................................
D. Distance From the Source .........................................................
E. Immunity Level.............................................................................
F. Report All Suspected EMI Incidents ............................................
G.EMI From Chair............................................................................
VI. GENERAL WARNINGS ...........................................................
A. Notice to User and Attendants......................................................
B. Weight Limit .................................................................................
C. Controller Settings ......................................................................
D.EMI ...............................................................................................
E. Safety Checklist ...........................................................................
F. Changes and Adjustments.........................................................
G. When Seated in a Parked Wheelchair .......................................
H. Environmental Conditions .........................................................
I. Terrain ............................................................................................
J. Street Use .....................................................................................
K. Motor Vehicle Safety ...................................................................
L. Center of Balance ........................................................................
M. Transfers......................................................................................
N. Reaching or Leaning .................................................................
O. Dressing or changing clothes ....................................................
P. Obstacles .....................................................................................
Q. Driving in Reverse.......................................................................
R. Ramps, Slopes & Sidehills ........................................................
S. To Reduce the Risk of Falls, Tip-over, or Loss of Control ......
T. Ramps at Home & Work ............................................................
U. Wheelchair Lifts ..........................................................................
V. Curbs & Single Steps..................................................................
W Stairs.............................................................................................
X. Escalators.....................................................................................
VII. WARNINGS: COMPONENTS & OPTIONS.........................
A. Armrests .......................................................................................
B. Batteries .......................................................................................
C. Cushion & Sling Seats................................................................
D. Fasteners .....................................................................................
E. Footrests.......................................................................................
F. Motor Lock....................................................................................
G. On/Off Switch ..............................................................................
H. Pneumatic Tires ..........................................................................
I. Positioning Belts ............................................................................
J. Push Handles ...............................................................................
K. Seating Systems .........................................................................
L. Upholstery Fabric.........................................................................
M. Power Seating.............................................................................
2
3
4
5
5
5
6
6
6
6
6
6
7
7
7
7
7
7
8
8
8
8
8
8
9
9
9
9
9
9
9
10
10
10
10
10
10
11
11
11
11
11
11
11
11
11
12
12
12
12
12
P. Power Recline ...............................................................
Q. Power Elevating Legrest Accessory .......................
R. Transit Use ....................................................................
VIII. SET UP, ADJUSTMENT & USE..............................
Notes ..................................................................................
Tools You Will Need...........................................................
A. Battery Removal ............................................................
B. Swing-Away Footrests ..................................................
C. Elevating Legrests (Optional) ......................................
D. Center Mount Hanger Adjustment.................................
E. Joystick ..............................................................................
F. To Adjust the depth of the Joystick.................................
G. To use the swing away function ..................................
H. Dual Post height adjustable armrest............................
I. Seat Depth .......................................................................
IX. OPERATING GUIDE...................................................
A. Circuit breakers .............................................................
B. Joystick Assembly .........................................................
C. Enhanced Display ........................................................
D. Motors Locks..................................................................
E. Performance Control Settings ......................................
F. Thermal Roll-Back .........................................................
G. Power Seating Operation through the Joystick..........
H. Power Tilt Operation......................................................
I. Power seat Lift Operation ...............................................
J. Power Tilt / Seat Lift Combo Operation........................
K. Power Recline Operation..............................................
L. Power Elevating Front Riggings Operation .................
M. Manual Recline Operation ...........................................
N. Adjustments ...................................................................
O. Troubleshooting Guide for Power Seating .................
X. BATTERIES ...................................................................
A. Introduction .....................................................................
B. Battery Charger..............................................................
C. Acid Burns ......................................................................
D. Connecting Batteries in Battery Compartment.............
E. Charging Batteries .........................................................
F. Disposing of Batteries.......................................................
XI. MAINTENANCE...........................................................
A. Notes ............................................................................
B. Cleaning.........................................................................
C. Storage Tips ...............................................................
D. Battery Maintenance ...................................................
E. Pneumatic Tires .............................................................
F. To Repair or Replace a Tire ..........................................
G. Ordering Parts................................................................
H. Maintenance Chart .......................................................
XII. AMYPOWER LIMITED WARRANTY ......................
1. Limited Warranty ............................................................
2. Replacement Parts Warranty........................................
3. What we will do...............................................................
13
13
13
13
13
13
14
14
15
15
15
15
15
16
16
17
17
17
17
17
18
18
18
19
20
21
22
23
24
25
26
27
27
27
27
27
28
28
28
28
28
28
29
29
29
29
29
30
30
30
30
N. CG Tilt Power Accessory ...........................................................
13
4. What you must do ..........................................................
30
O. 11” Seat Lift Power Accessory ..................................................
13
5. Notice to Consumer .......................................................
30
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
3
YOUR AMYPOWER ALLTRACK R3 OR R POWER WHEELCHAIR AND ITS PARTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
2
3
14
4
7
8
1
Armrest
Joystick
Seat Pan
Front Hanger
Caster Tire
Foot Plates
Backrest
Push Handle
Free-wheel Release Lever
Seat Frame
Drive Wheels
Base Frame
Caster Fork
Headrest
6
9
10
11
5
12
13
Base Chair User Weight Limits*
Up to 400 lbs
*Weight capacity may vary due to
options chosen, refer to
appropriate order form.
Battery Sizes
Two deep cycle batteries are required to
operate this power wheelchair
Group 22NF
Group 24
Armrests
Standard Cantilever
Optional Dual Post
Optional Reclining
Flip-Back and height-adjustable
Battery Charger
8 amp off-board
Optional Lester 8 amp off-board
Seat to Floor Height
From 15 ¾" to 20”
The height may vary due to options
chosen, refer to appropriate order form.
Footrest
Standard Swing-away Footrests
Heavy-Duty Footrests
Manual Elevating & Articulating Legrests
Power Elevating & Articulating Legrests
Angle Adjustable from 60°, 70°, 80°
Angle-adjustable footplates
Heel loops
Calf Pads
Adjustable leg length
Drive Wheels
14" x 3"
Optional 12.5" x 3"
Caster Fork
Standard - Fixed
Casters
6" Solid, Optional 8” pneumatic or
8” Pneumatic with solid inserts
Tire Type
Standard pneumatic
Optional with solid insert
Seat Lift (Option)
11" elevation 300 lb or 400lb max
user weight capacity
Tilt (Option)
50° CG Tilt 400 lb capacity
Power Recline (Option)
400 lb capacity
89° to 160° Range
Joystick Mount
Standard fixed Joystick
(right or left hand mount)
Optional swing-away mount
Height Adjustability
Seat Width Range
Adjustable from 15” to 20”
Adjustable from 19” to 24”
Custom width available
Seat Depth Range
Adjustable from 15" to 22"
Custom depth available
Back Cane Height
12" - 22"
Contour Backrest
From 15” to 24” Wide
12” to 22” High (Even numbers only)
Center Mounts
Solid one-piece Foot Platform
Angle adjustable Split Footplates
Power Elevating & Articulating Footboard
Calf Pads
Adjustable Leg Length
NOTE:
All features may not be available with some
chair setups or in conjunction with another
chair feature. Please consult your supplier
for more information. Your authorized
supplier can also provide you with more
information on accessories.
Back Angle
86° to 122° in 4° increments,
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
4
IV. NOTICE –READ BEFORE USE
A. Choose the Right Chair & Safety Options
Amypower provides a choice of many power
wheelchair styles, sizes and adjustments to meet
the needs of the user. However, final selection of
a wheelchair rests solely with you and your health
care professional. Choosing the best chair for you
depends on such things as:
VI - GENERAL WARNINGS
Here you will find a safety checklist and a
summary of risks you need to be aware of before
you ride this chair.
VII - WARNINGS — COMPONENTS & OPTIONS Here
you will learn about your chair. Consult your supplier
and your health care professional to help you choose
the best set-up and options for your safety.
1. Your size, disability, strength, balance coordination.
2. Your intended use and your level of activity.
3. The types of hazards you must overcome in daily
use (in areas where you are likely to use your chair).
4. The need for options for your safety and comfort
(such as positioning belts or specialty seating
systems).
XI - BATTERIES
Here you will learn about battery and charger
safety, and how to avoid injury.
NOTE- Where they apply, you will also find “Warnings”
in other sections of this Manual.
B. Adjust Chair to Your Ability
You need to work with your doctor, nurse or therapist,
and your supplier, to fit this chair and adjust the
controller settings for your level of function and ability.
Throughout this owner’s manual and on the
wheelchair you will see the icons listed below
to identify warnings and potential hazards. It is
important to read all of them and understand
them.
C. Review this Manual Often
Before using this chair, you and each person who
may assist you, should read this entire Manual and
make sure to follow all instructions. Review the
warnings often, until they are second nature to you.
WARNING! These warnings must be followed, failure
to do so may cause personal injury or may dam- age
the wheelchair.
D. Warnings
The word “WARNING” refers to a hazard or unsafe
practice that may cause severe injury or death to
you or to other persons. The “Warnings” are in four
main sections, as follows:
PROHIBITED! Prohibited actions must never be
performed. Performing an action that is prohibited can
cause personal injury or may damage the wheelchair.
NOTE: Notes are informative statements to help further
explain actions, warnings or product detail.
E. Caution
Federal law restricts this device to sale by or on the
order of a practitioner licensed by the law of the State in
which he/she practices.
ESD: Electrostatic Discharge has a potential to
damage printed circuit boards unless handled correctly.
When the ESD symbol is shown throughout the owner’s
manual, use the Proper Handling Techniques insert
supplied with the chair to properly handle this situation.
1. V - EMI
Here you will learn about electromagnetic
interference and how it can affect your chair.
V. EMI (ELECTROMAGNETIC INTERFERENCE)
WARNING
Read all warnings to reduce the risk of
unintended brake release or chair movement:
1. Beware of the danger from hand-held
transceivers. Never turn on or use a hand-held
transceiver while power to your chair is on. Use
extra care if you believe that such a device may
be in use near your chair.
2. Be aware of nearby radio or TV stations, and
avoid coming close to them.
3. If unintended movement occurs, turn your chair off
as soon as it is safe to do so.
WARNING - A. WHAT IS EMI?
1. EMI means: electromagnetic (EM) interference (I).
EMI comes from radio wave sources such as radio
transmitters and transceivers. (A “transceiver” is a
device that both sends and receives radio wave signals).
2. There are a number of sources of intense EMI in
your daily environment. Some of these are obvious
and easy to avoid. Others are not, and you may not
be able to avoid them.
3. Powered wheelchairs may be susceptible to
electromagnetic interference (EMI) emitted from
sources such as radio stations, TV stations, amateur
radio (HAM) transmitters, two way radios, and cellular
phones.
4. EMI can also be produced by conducted sources
or electrostatic discharge (ESD).
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
5
WARNING B. WHAT EFFECT CAN EMI HAVE?
1. EMI can cause your chair, without warning, to:
 Release its brakes
 Move by itself
 Move in unintended directions
If any of these occurs, it could result in severe injury
to you or others.
2. EMI can damage the control system of your chair.
This could create a safety hazard, and lead to costly
repairs.
WARNING C. SOURCES OF EMI
The sources of EMI fall into three broad types:
1. Hand-Held Transceivers:
The antenna is usually mounted directly on the unit. These
include:
 Citizens band (CB) radios

“Walkie-talkies”
 Security, fire and police radios
 Cellular phones
 Lap-top computers with phone or fax
 Other personal communication devices
2. Medium-Range Mobile Transceivers:
NOTE: These devices can transmit signals while they are
on, even if they are not in use.
3. The configuration tested was found to be immune to at
least 20 V/m is: Amypower Alltrack power wheelchair with
a right- hand mounted P & G remote joystick system, 18"
seat width, 18" seat depth, dual post height adjustable
armrests, fixed tapered legrests with one piece solid
footplate, and Group 24 gel cell batteries.
4. The following specialty input devices have an
unknown effect on the immunity level because they
have not been tested with the Amypower Alltrack
and PG Drives control system:
Breath Control
• Star Board
Proportional Head
• Proximity Head Array
Control
• Wafer Board
Tri-Switch Head Array
• Zero Touch Switch
Proportional Mini• Penta Switch
Joystick/Chin Control
• 4-Zero Touch Switch
Heavy Duty Switched
• Plate Switch
Joystick
• 5-Zero Touch Switch
Buddy Button
• Soft Switch
Treadle Switch
• Disc Switch
Micro Light
• Grasp Switch
Ribbon Switch
• Wobble Switch
WARNING
Individuals with physical limitations requiring the use of
a specialty control input device known not to be
immune to 20V/m, or not known, should exercise
extra care around known sources of EMI.
WARNING
These include two-way radios used in police cars, fire
trucks, ambulances and taxi cabs. The antenna is
usually mounted on the outside of the vehicle.
3. Long-Range Transceivers:
These include commercial radio and TV broadcast
antenna towers and amateur (HAM) radios.
NOTE- The following are not likely to cause EMI problems:
Laptop computers (without phone or fax),
Cordless phones, TV sets or AM/FM radios, CD or tape
players.
WARNING D.DISTANCE FROM THE SOURCE
EM energy rapidly becomes more intense as you get
closer to the source. For this reason, EMI from handheld devices is of special concern. (See C.1 above) A
person using one of these devices can bring high levels
of EM energy very close to your chair without you
knowing it.
There is no way to know the effect on EMI if you add
accessories or modify this chair. Any change to your chair
may increase the risk of EMI. Parts not specifically tested
or parts from other suppliers have unknown EMI properties.
WARNING F. REPORT ALL SUSPECTED EMI INCIDENTS
You should promptly report any unintended movement or
brake release. Be sure to indicate whether there was a
radio wave source near your chair at the time. Contact:
Amypower’s Customer Service Department at
(888) 453-0311
WARNING G.EMI FROM CHAIR
The chair itself can disturb the performance of electromagnetic fields such as emitted by alarm systems of shops.
WARNING E. IMMUNITY LEVEL
1. The level of EM is measured in volts per meter
(V/m). Every power wheelchair can resist EMI up to a
certain level. This is called its “immunity level”.
2. The higher the immunity level, the less the risk of
EMI. It is believed that a 20 V/m immunity level will
protect the power wheelchair user from the more
common sources of radio waves.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
6
VI. GENERAL WARNINGS
WARNING
Heed all warnings in this section. If you fail to do
so a fall, tip-over or loss of control may occur
and cause severe injury to you or others.
A. NOTICE TO USER AND ATTENDANTS
WARNING - User
1. Before using this chair, you should be trained in
its safe use by your health care professional.
2. Every wheelchair is different. Take the time to learn
the feel of this chair before you begin riding.
3. Be aware that you must develop your own methods
for the safe use of this chair, which are best suited to
your level of function and ability.
4. Have someone help you practice bending,
reaching and transfers until you learn how to
do them safely.
5. Never try a new maneuver on your own unless you are
sure it is safe.
6. Get to know the areas where you plan to use your
chair. Look for hazards and learn how to avoid
them.
7. Always wear a positioning strap.
8. Do not use a wheelchair if the joystick does not
spring back to the neutral position.
9. Do not use your wheelchair if the joystick boot is
ripped or damaged.
10.Do not try to tip this wheelchair without an attendant
present.
User and Attendants
1. When transferring the user in or out of the wheelchair
never use the footplate as a platform.
2. Do not lift this wheelchair by any parts that are
removable, doing so may result in damage to the
wheelchair or injury to the user.
3. Never try to stop or slow this wheelchair with the
wheel locks (if applicable). Wheel locks are
designed to prevent the chair from moving when
stopped. They are not brakes.
4. Always keep your hands and body parts clear of
moving parts to help prevent injuries.
WARNING - Attendants
Make sure you heed all warnings and follow all instructions in
each section of this manual. Be aware that warnings that apply
to the user also apply to you.
1. Do not stand or sit on any portion of this wheelchair.
2. You need to work with the user, and the user’s
doctor, nurse or therapist, to develop safe methods
best suited to your abilities and those of the user.
3. To manually push the chair you must release the motor
locks.
 Do not engage or disengage motor locks unless
power to the chair is off. In addition, make sure
both free wheel levers are completely pushed in
before turning the power on to ensure the
wheelchair can be driven in a straight forward
motion.
 Make sure you have full control over the chair
when you release the motor locks. When you do
so the chair will not have brakes.

Make sure the chair is on level ground before you
release the motor locks.
NOTE- To release the wheel locks the wheel chair may
need to be rocked back and forth slightly several times
before the lock will release.
4. Propel this chair by the push handles only. They provide
secure points for you to hold onto the rear of the chair to
prevent a fall or tip-over.
 Check to make sure push handle grips will not
rotate or slip off.
WARNING - B. WEIGHT LIMIT
1. The user plus items carried should never exceed the
total
weight capacity identified on your chair.
2. Never use this chair for weight training if the total
weight (user plus additional weights) exceeds weight
capacity.
3. Exceeding the weight limit is likely to damage the
seat, frame, or fasteners, and may cause severe
injury to you or others from chair failure.
4. Exceeding the weight limit will void the warranty.
WARNING - C. CONTROLLER SETTINGS
Be aware that you may need to adjust the controller
settings of your chair.
1. Check and adjust the settings every six to twelve
months.
2. Consult your supplier to adjust the control
settings immediately if you notice any change in
your ability to:
 Control the joystick
 Hold your torso erect
 Avoid running into objects.
WARNING - D.EMI
Read Section V to learn about EMI. To reduce the risk
of unintended brake release or chair movement:
1. Never turn on or use a hand-held transceiver while
power to your chair is on. Use extra care if you believe
that such a device may be in use near your chair.
2. Be aware of nearby radio or TV stations, and avoid
coming close to them.
3. If unintended movement or brake release occurs,
turn your chair off as soon as it is safe.
WARNING - E. SAFETY CHECK-LIST
Before each use of this chair:
1. Make sure the chair operates smoothly. Check for
noise, vibration, or a change in ease of use. (These
may indicate low tire pressure, loose fasteners, or
damage to your chair).
 If you detect a problem, make sure to repair or
adjust the chair. Your supplier can help you find and
correct the problem.
2. Make sure batteries are charged. Green lights on charge
indicator will light up when charge is full. Yellow lights
indicate battery charge level is getting low. Red lights
indicate batteries are in immediate need of charging.
3. When not in use, keep your chair in a clean dry
place.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
7
PROHIBITED - F. CHANGES & ADJUSTMENTS
Never use non-Amypower parts to replace Amypower
provided parts or make changes to your chair unless
authorized by Amypower. (Doing so will void the
warranty and may create a safety hazard.)
WARNING
Accessories designed by manufacturers other than
Amypower is not available through Amypower the order
process have not been tested or approved for use by
Amypower.
1. If you modify or adjust this chair it may increase the
risk of a fall or tip-over.
2.Modifications unauthorized by Amypower constitute
remanufacturing of the wheelchair. This voids the
warranty. The user then assumes all future liability for the
wheelchair.
WARNING - G. WHEN SEATED IN A PARKED
WHEELCHAIR
1. Always turn off all power to your chair when you
are parked, even for a moment. This will prevent:
 Accidental movement from contact with the joystick
by you or others.
 Unintended brake release or movement from
EMI sources. (See Section V)
2. Make sure that persons who help you (for example,
store clerks) are aware of the joystick and do not touch
it. If they
do, your chair may move suddenly when you do not
expect it.
WARNING - H. ENVIRONMENTAL CONDITIONS
Your chair is not designed for use in a heavy
rain storm, or in snowy or icy conditions.
1. Contact with water or excessive moisture can cause
an electrical malfunction. The frame, motors and other
chair parts are not water-tight and may rust or corrode
from the inside.
To avoid a chair failure:
 Minimize exposure of your chair to rain or very wet
conditions.
 Never take your chair into a shower, tub, pool or sauna.
 Do not use your chair in fresh or salt water (such
as at the edge of a stream, lake, or ocean).
 Make sure battery cover is secure.
 Replace joystick boot if it becomes torn or cracked.
 Make sure all electrical connections are secure.
 Dry the chair as soon as you can if it gets wet, or if
you use water to clean it.
 Never operate your chair on a slope or ramp if there is
snow, ice, water or an oil film present.
WARNING
Extra caution should be used when employing the disc
switch or the proximity head array as control devices.
These two devices are susceptible to malfunction when
wet.
WARNING - I. TERRAIN
1. This chair will perform at optimum on firm, even
surfaces such as concrete, asphalt and indoor flooring.
2. Although equipped with suspension, the performance can
be substantially reduced on uneven surfaces and rough
terrain.
3. Do not operate the chair on sand, loose gravel or
soil. Doing so may damage wheels, bearings, axles,
motors or loosen fasteners.
WARNING - J. STREET USE
In most provinces, power chairs are not legal for use on
public roads. Be alert to the danger of motor vehicles on
roads or in parking lots.
1. Do not operate this wheelchair on any roadways
that do not allow non-motor vehicle traffic.
2. When visibility is limited by either darkness or
weather conditions, do not operate the chair on any
roadways.
3. It may be hard for drivers to see you. Make eye contact
with drivers before you proceed. When in doubt, yield until
you are sure it is safe.
WARNING - K. MOTOR VEHICLE SAFETY
Your chair has been manufactured with built-in
Transport Brackets only.
These transport brackets have not been crashtested in accordance with WC-1 9. Use these
transport brackets only to secure an unoccupied
wheelchair during transport
1. NEVER let anyone sit in this chair while in a moving
vehicle.
2. NEVER transport this chair in the front seat of a
vehicle. It may shift and interfere with the driver
3. ALWAYS secure this chair so that it cannot roll or shift.
4. Do not use any chair that has been involved in
a motor vehicle accident
2. Proceed slowly and use extra care if you must
operate your chair on a wet or slick surface.
 When in doubt, have someone help you.
 Do so only if you are sure it is safe.
 Stop if one or both main wheels lose traction. If
this occurs, you may lose control of your chair or
fall.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
8
WARNING - L. CENTER OF BALANCE
The point where this chair will tip forward, back, or to
the side depends on its center of balance and stability.
The Center Of Balance Is Affected By:
1. The seat height and seat angle.
2. A change in your body position, posture or weight
distribution.
3. Using this chair on a ramp or slope.
4. The use of a back pack or other options, and the
amount of added weight.
5. Drive wheel positioning.
To Reduce The Risk Of A Fall Or Tip-Over:
Whenever a condition exists that may change the
center of balance, reduce speed, proceed
cautiously, and when in doubt, always have
someone help you.
WARNING - M. TRANSFERS
It is dangerous to transfer on your own. It requires good
balance and agility. Be aware that there is a point during
every transfer when the wheelchair seat is not below you.
To prevent a fall:
1. Always turn off power before you transfer to or from
your chair. If you fail to do so you may touch the
joystick and cause your chair to move when you do
not expect it.
2. Make sure motor locks are engaged. This keeps
the chair from moving when you transfer.
3. Work with your health care professional to learn safe
methods.

Learn how to position your body and how to
support yourself during a transfer.

Have someone help you until you are sure you
can do a safe transfer on your own.
4. Move your chair as close as you can to the
seat you are transferring to. If possible, use a
transfer board.
5. Rotate the front casters until they are as far forward as
possible.
6. Be careful of the footrests. If you can, remove or
swing them out of the way.

Never stand on footrests when you transfer.
Doing so may damage them or cause your chair to
tip.

Make sure your feet do not “hang up” or get
caught in the space between the footrests.
7. Make sure armrests do not interfere.
8. Transfer as far back onto the seat surface as you
can. This will reduce the risk that you will miss the
seat or fall.
WARNING - N. REACHING OR LEANING
Reaching or leaning affects the center of balance of your
chair. If done improperly, a fall or tip-over is likely. When
in doubt, ask for help or use a device to extend your
reach.
To Reduce the Risk of injury and/or Damage to the Chair:
1. Never reach or lean if you must shift your weight
sideways or rise up off the seat.
2. Never reach or lean if you must move forward in your seat
to do so. Always keep your buttocks in contact with the
backrest.
3. Never reach with both hands (you may not be able to
catch yourself to prevent a fall if you lose your
balance).
4. Never try to pick up an object from the floor by
reaching down between your knees.
5. Never put pressure on the footrests while reaching.
6. Never reach or lean over the top of the seat back.
This may damage the backrest and cause you to
fall.
IF YOU MUST REACH OR LEAN, DO SO AT
YOUR OWN RISK.
Remember to:
1. Move your chair as close as you can to the object
you wish to reach.
2. Rotate the front casters until they are as far forward
as possible. This makes the chair more stable.
NOTE- To do this: Move your chair past the object you
want to reach then back up alongside it. Backing up
will rotate the casters forward.
3. Turn off all power to your chair. If you fail to do so,
you may touch the joystick and cause your chair to move
when you do not expect it.
WARNING - O. DRESSING OR CHANGING CLOTHES
Be aware that your weight will shift if you dress or
change clothes while seated in this chair. To make the
chair more stable, rotate the front casters until they are
forward.
WARNING - P. OBSTACLES
Obstacles you may have to overcome in daily use
include door thresholds, lifts, ramps and hazards
such as potholes and broken pavement. These
can damage your chair and may cause a fall, tipover or loss of control.
1. Be aware that thresholds are very dangerous. (Even
a small change in height may stop a caster wheel and
cause your chair to tip). You may need to:
Remove or cover threshold strips between rooms.
Install a ramp at entry or exit doors.
2. Keep your eyes moving when you ride; scan the
area well ahead of your chair.
3. Make sure the floor areas where you use this chair
are level and free of obstacles.
WARNING - Q. DRIVING IN REVERSE
Use extra care when you drive your chair in
reverse. You may lose control or fall if one of the
rear wheels hits an object.
1. Operate your chair slowly and at an even speed.
2. Stop often and check to make sure your
path is clear of obstacles.
WARNING - R. RAMPS, SLOPES & SIDEHILLS
The center of balance of your chair changes
when you are on a slope.
NOTE- “Slope” includes a ramp or side hill. Your chair is less
stable when it is at an angle. Never use this chair on a slope
unless you are sure it is safe. When in doubt, have someone
help you.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
9
Beware Of:
1. Steep slopes. Do not use this chair on a slope
steeper than 10%. (A 10% slope means: One foot in
elevation for every ten feet of slope length).
2. Wet or slippery surfaces (such as when ice, snow,
water or oil film is present). A loss of traction may cause a
fall or tip-over.
3. A change in grade on a slope (or a lip, bump or
depression). These may cause a fall or tip-over.
4. A drop-off at the bottom of a slope. (A drop-off of as
small as 3/4 inch (19 mm) can stop a front caster and
cause the chair to tip forward).
WARNING - S. TO REDUCE THE RISK OF A FALL, TIPOVER OR LOSS OF CONTROL:
1. Never use your chair on a slope unless you are
sure you can do so without losing traction.
2. Always go as straight up and as straight down as you can.
 Do not “cut the corner” on a slope or ramp.
 Do not turn or change direction on a slope.
3. Always stay in the center of the ramp. Make sure
ramp is wide enough that you are not at risk that a
wheel may roll off the side.
4. Keep your chair moving at a slow, steady speed. Keep
control over the chair at all times.
 On a descent, do not let your chair accelerate
beyond its normal speed.
 If the chair picks up speed, center the joystick to
slow down or stop.
NOTE- The solid state controller of your chair has a logic
system that will help control your speed
when driving on a slope or uphill.

If you stop, re-start slowly.
WARNING - T. RAMPS AT HOME & WORK
Before driving on a ramp, survey the condition of the ramp.
On slippery ramps traction may be reduced causing your
wheelchair to slide.
WARNING
Make sure ramps meet all Building Codes for your area.
1. For your safety, have a licensed contractor build or
remodel ramp to meet all standards.
NOTE- The proper design will vary, depending on
such things as: the length and height of the ramp; the need
for an intermediate platform; landing size; doors, and the
direction
of swing, and; whether the ramp includes a turn or angle.
WARNING - U. WHEELCHAIR LIFTS
Wheelchair lifts are used in vans, buses, and
buildings to help you move from one level to another.
1. Always turn off all power to your chair when you are on
a lift. If you fail to do so, you may touch the joystick by
accident and cause your chair to drive off the platform. (Be
aware that a “roll-stop” at the end of the platform may
not prevent this).
2. Make sure there is not a lip or drop-off at the top or
bottom of the platform. These may cause a fall or tip-over.
When in doubt, have someone help you.
3. Always position the user securely in the chair to
help prevent falls while on a lift.
4. Avoid moving forward if a wheel is “hung up” on the
lip of the ramp. Backup, reposition the caster for a more
direct approach. And slowly try again.
WARNING - V. CURBS & SINGLE STEPS
1. It is recommended to climb and/or descend a curb,
single step, or other obstacle that a ramp or curb cut out
is always used.
2. If you must climb or descend a curb, single step,
or other obstacle that is greater than 2.5", it is
recommended to have a person assist you in doing so.
3. In no case should you try to climb a curb, single
step, or other obstacle greater than 4" high.
4. If you must climb or descend a curb or step alone do
so at your own risk using extreme care and follow the
following procedure:
 Proceed slowly, at a steady speed
 Go as straight up or down as you can over the
obstacle. Never turn when trying to climb or descend
and obstacle, doing so may result in a fall or tip-over.
5. Failure to follow the above procedures may cause:
 A Fall or Tip Over
 Damage to the frame, wheels, axles or other
parts, or loose fasteners.
PROHIBITED! - W. STAIRS
Never use this chair to go up or down stairs, even with
an attendant. Doing so is likely to cause a fall or tip-over.
PROHIBITED! - X. ESCALATORS
Never take this chair on an escalator, even with an attendant.
Doing so is likely to cause a fall or tip-over.
At A Minimum:
1. Open sides of ramp must have side rails to prevent
your chair from going over the edge.
2. Slope must not be steeper than one inch in height for
every one foot of slope length (approximately 10º).
3. Ramp surface must be even, and have a non-skid surface.
4. You may need to add a section at the top or bottom to
avoid a lip or drop-off.
5. Ramp must be sturdy. Add bracing if needed, so
ramp does not “bow ” when you ride on it.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
10
VII. WARNINGS: COMPONENTS & OPTIONS
WARNING
Note: If you use parts or make changes not
authorized by Amypower it may create a safety
hazard and will void the Warranty.
WARNING
A. ARMRESTS
Armrests will not bear the weight of this chair.
PROHIBITED!
Never lift this chair by its armrests. They may
come loose or break.
WARNING
B. BATTERIES
Always wear rubber gloves and safety glasses
when you handle batteries.
PROHIBITED!
Never smoke or hold an open flame near
batteries. They are a known explosion hazard.
WARNING
1. Only deep cycle sealed case construction batteries
should be used in this device.
2. To prevent an acid spill, always keep batteries
upright (wet cell batteries).
3. Read all of section X. Batteries before attempting to
change, or charge batteries.
WARNING
C. CUSHIONS & SLING SEATS
1. Standard foam cushions and other body supports
are not designed for the relief of pressure.
2. If you suffer from pressure sores, or if you are at
risk that they will occur, you may need a special seat
system or a device to control your posture.
3. Consult your doctor, nurse or therapist to find out if
you need such a device for your well-being.
WARNING
D. FASTENERS
Many of the screws, bolts and nuts on this chair are special
high- strength fasteners. Use of improper fasteners may
cause your chair to fail.
1. Only use fasteners provided by Amypower.
2. If fasteners become loose, tighten them immediately.
3. Over- or under-tightened fasteners may fail or cause
damage to chair parts.
4. See Section VIII, “Set-Up, Adjustment &
Use”, for proper torque settings.
WARNING
E. FOOTRESTS
1. At the lowest point, footrests should be at least 2 1/2
inches (65 mm) off the ground. If set too LOW, they may
“hang up” on obstacles you can expect to find in normal
use. This may cause the chair to stop suddenly and tip
forward.
2. To avoid a trip or fall when you transfer:
Make sure your feet do not “hang up” or get
caught in the space between the footrests.
Avoid putting weight on the footrests, as the chair
may tip forward.
Remove or swing the footrests out of the way, if possible.
3. The footrest should always be in the down position
when operating the chair.
PROHIBITED!
Never lift this chair by the footrests. Footrests detach and will
not bear the weight of this chair. Lift this chair only by nondetachable parts of the main frame.
WARNING
F. MOTOR LOCKS
1. Do not engage or disengage motor locks unless
power to the chair is off. In addition, make sure both
free wheel levers are completely pushed in before
turning the power on to ensure the wheelchair can be
driven in a straight forward motion.
2. Be aware that the chair will not have brakes when
motor locks are in the free-wheel position.
3. Make sure that the person pushing the chair has full
control when motor locks are disengaged.
4. Make sure that the chair is on level ground when
motor locks are disengaged.
NOTE- To release the wheel locks the wheel chair may
need to be rocked back and forth slightly several times
before the lock will release.
WARNING
G. ON/OFF SWITCH
1. Never use the ON/OFF switch to stop the chair except in
an emergency. This will result in an abrupt stop,
and may cause you to fall.
2. To slow your chair to a stop, return the joystick to neutral.
WARNING
H. PNEUMATIC TIRES
Proper inflation extends the life of your tires and
makes your chair easier to use.
1. Do not use this chair if any of the tires are under- or
over- Inflated. Check weekly for proper inflation level,
as listed on the tire sidewall.
2. Low pressure in a tire may cause the chair to veer
to one side and result in a loss of control.
3. An over-inflated tire may burst.
4. Never use a gas station air pump to inflate a tire.
Such pumps provide air at high volume, and could
cause the tire to burst. To prevent tire damage:

Use a hand pump (or low volume air pump) to inflate
tires.

Use a tire gauge to check pressure.
5. Driving over sharp objects may cause damage to
pneumatic tires and tubes.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
11
WARNING
I. POSITIONING BELTS
WARNING
M. POWER SEATING
Use a positioning belt only to help support your posture. Improper use of such belts may cause severe injury or death.
1. Make sure you are not at risk to slide down in the
wheelchair seat. If this occurs, you may suffer chest
compression or suffocate due to pressure from the belt.
2. A pelvic wedge or a similar device can help keep
you from sliding down in the seat. Consult your
health care professional to find out if you need such
a device.
3. The belt must be snug, but must not be so tight that it
interferes with breathing. You should be able to slide
your open hand, flat, between the belt and your
stomach.
4. Make sure you can easily remove the belt in an emergency.
1. Operation
 While driving this wheelchair in the reclined,
elevated, or tilted position use caution.
 Do Not attempt to operate any power seating
option while positioned on an incline.
 Do Not attempt to operate any power seating
option while this wheelchair is in motion.
 Do not attempt to operate the lift or tilt power
seating options around children.
 Through programming it is possible to reverse the
direction of all powered seating functions, ensure
you know which direction your seat is going to
move before operating.
PROHIBITED!
Never use a positioning belt:
 In place of a motor vehicle seat belt. In an accident or
sudden stop you may be thrown from the chair. A positioning
belt will not prevent this, and further injury may
result from the belt.
 As a restraint. A restraint requires a doctor’s order.
 On a user who is comatose or agitated.
WARNING
J. PUSH HANDLES
1. Push handles provide secure points for an attendant to
propel and control the chair. This helps to prevent a fall or tipover.
2. Check to make sure push handle grips will not rotate or slip
off.
WARNING
K. SEATING SYSTEMS
1. Use of a seating system not approved by
Amypower may alter the center of balance of
this chair. This may cause a fall or tip-over.
2. Never change the seating system of your chair
unless you consult your supplier first.
3. Never raise your seating system to a height of more
than 22" (measuring from the front of the seat pan to
the floor).
WARNING
L. UPHOLSTERY FABRIC
1. Replace worn or torn fabric of seat sling and seat
back as soon as you can. If you fail to do so, the
seat may fail and cause you to fall. Worn fabrics
may increase the potential for a fire hazard.
2. Sling fabric will deteriorate with age and use. Look for
fraying, thin spots, or stretching of fabric at rivet
holes. Replace fabric as required.
3. Be aware that washing may reduce flame retardation
of the fabric.
2. Reduced Speed Driving (Creep)
This power chair is designed to automatically
reduce the maximum driving speed to a creep
mode when it is equipped with a seat lift. Creep
mode is activated when it has reached a
maximum limit of 3” of seat elevation.
3. Pinch points
Pinch points may occur when operating the powered
seating options on this chair. Ensure all hands and
body parts are clear of all power seating components
that may result in pinch points before operating them.
4. Tilting Power Base with Push Handles
Do not attempt to tilt power wheelchairs by pulling
down on the push handles. Power wheelchairs
have heavy bases. As such, attempting to tilt a
power wheelchair to traverse obstacles can
damage components in the seating system and/or
modular actuators.
5. Remain Clear During Power Accessory Operation
Please stay clear of any powered actuator while the
component is in motion. Amypower power mechanisms
move over large ranges of travel. Users should be aware
of their surroundings while components are in motion.
6. Maximum User Weight
Do not exceed the weight capacity for your specific
chair/seating system configuration. Doing so could
result in premature failure or injury.
7.
Latch Mode
While operating any power seating function in
latched mode use caution. In latch mode, powered
seating will not stop until a reverse command is
performed or the end of travel is met.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
12
WARNING
N. CG TILT POWER ACCESSORY
Pinch Point
Avoid putting hands or fingers near the power tilt
mechanism while in operation.
The powered CG Tilt accessory for this chair has a
maximum user weight capacity range from 300 lbs up
to 400 lbs depending on the chair configuration. Never
exceed the specified capacity while operating the
powered actuator.
WARNING
O. 11” SEAT LIFT POWER ACCESSORY
Pinch Point
Avoid putting hands or fingers near the power seat lift
mechanism while in operation.
The powered lift modular accessory for this chair has
a maximum user weight capacity of up to 300 lbs or
400 lbs depending on your chair configuration. Never
exceed this capacity while operating the powered
actuator.
WARNING
P. POWER RECLINE
Pinch Point
Avoid putting hands or fingers near the power recline
mechanism while in operation.
The maximum user weight capacity for the power recline is
from 300 lbs up to 400 lbs depending on the chair
configuration. Exceeding this weight capacity could lead to
injury and/or permanent damage to the equipment.
WARNING
Q. POWER ELEVATING LEGREST ACCESSORY
Pinch Point
Avoid putting hands or fingers near the power elevating
legrests or center mount mechanism while in operation.
The power legrest accessory for the Alltrack R has a maximum
user weight capacity of up to 300 lbs or 400 lbs depending on
your chair configuration. Never exceed this capacity while
operating the powered actuator.
WARNING
R. TRANSIT USE
Your chair has been manufactured with built-in Transport
Brackets on.
These transport brackets have not been crash-tested in
accordance with WC-19. Use these transport brackets only to
secure an unoccupied wheelchair during transport
1. NEVER let anyone sit in this chair while in a
moving vehicle.
2. NEVER transport this chair in the front seat of a
vehicle. It may shift and interfere with the driver
3. ALWAYS secure this chair so that it cannot
roll or shift.
4. Do not use any chair that has been involved in a
motor vehicle accident.
VIII. SET-UP, ADJUSTMENT AND USE
NOTES
1. Work Surface for Set-Up:
Use a flat surface, such as a table, to assemble, adjust and
check your chair. This makes the steps easier and helps
ensure a correct set-up.
2. Fasteners:
 Many of the screws and bolts on this chair are special
high- strength fasteners and may have special coatings.
 Many nuts are of the Nylock type. They have a plastic
insert to help prevent loosening.
 Only use screws, bolts and nuts provided by Amypower.
WARNING
1. Use of improper fasteners may cause the chair to fail.
2. Over- or under-tightened fasteners may fail or
cause damage to chair parts.
3. If bolts or screws become loose, tighten them as
soon as you can. Loose bolts or screws can cause
damage to other chair parts causing them to fail.
3. Washers & Spacers:
 Note the position of washers and spacers before
disassembly.

To avoid damage to the frame, replace all washers
and spacers when you reassemble parts.
TOOLS YOU WILL NEED
1. Basic Tool Kit:
To set-up, adjust and maintain your chair you
may need the following tools:
 Combined Phillips and flat screw driver
 Standard metric wrenches from 10mm
 Metric Allen wrenches from 5mm
 Imperial wrenches from 1/4" to 9/16"
 Imperial Allen wrenches from 5/64" to 1/4"
These tools can be found in standard hardware
stores.
2. Torque Wrench:
If you plan to adjust and maintain this chair
yourself, Amypower recommends that you use a
torque wrench.
NOTE- The wrench must measure inch-pounds (N.m). You
can buy a torque wrench and proper sockets from a hardware
store.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
13
A. BATTERY REMOVAL
To remove the batteries for transporting or servicing:
Remove Batteries
a. Push panel when pulling the handle (a).
b. Drop panel and pull-out tray extension (b).
c. Carefully pull battery pack until cable connection is
accessible
d. Disconnect and pull tray to full deployment to remove the
batteries.
e. Lift the battery from the compartment using the battery
carrying straps.
f. Repeat operation in reversed steps to put the batteries
back in.
a
WARNING
Batteries may weigh up to 55 lbs. (25 kg). Care must be
taken to avoid injury when lifting.
c
b
B. SWING-AWAY FOOTRESTS
1. Installation
a. Place swing-away pivot pin (d) into the locating hole on top of
the hanger mount with the footrest facing outward from frame.
Rotate the footrest inward until latch plate locks (e) into place on
locking bolt..
2. Removal
a. To remove footrest, press quick-release lever (e).
b. Rotate footrest outward and lift.
3. Height Adjustment
a. Remove both bolts (f) in the hanger frame tube.
b. Reposition the footrest.
c. Re-tighten all bolts (f).
d
e
f
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
14
C. ELEVATING LEGREST (OPTIONAL)
1. Installation
To install or remove Elevating legrests (ELR) see
instructions for Swing-away Footrest installation.
J
D. CENTER MOUNT HANGER ADJUSTMENT
1. Height Adjustment
a. Remove the two securing bolts (j).
b. Move footplate to desired height.
c. Re-install bolts (j) through desired holes.
2. Calf Pad Adjustment
a. Remove the one securing bolt (j)
b. Move calf pad to desired height.
c. Re-install bolts (j) through desired hole.
K
E. JOYSTICK
L
Please refer to the PG Drives user’s manual provided with the
information package
F. TO ADJUST THE DEPTH OF THE JOYSTICK
1. Loosen the wing-nut (k).
2. Slide the mounting bracket (tube) (l) in or out until in desired
position.
3. Retighten the wing-nut (k)
G. TO USE THE SWING AWAY FUNCTION
1. Push down to release the lever (m)
2. Continue pushing down until the joystick bracket is fully
retracted.
3. To bring back, pull the joystick firmly towards you until it gets
back in its locked position.
M
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
15
H. DUAL-POST HEIGHT-ADJUSTABLE ARM RESTS
The dual-post flip-back armrest can be used as
either a flip-back armrest or a removable armrest.
1. Installing Armrest
a. Insert front and rear posts into armrest receivers.
b. Engage lever (A) and insert the rear safety pin (B).
2. Set-up for Flip-back Operation
a. Disengage lever (A) so front post is able to come free.
b. Armrest now has the ability to be flipped back without
removal.
3. Set-up for Removal
a. Disengage levers (A) and pull out
the rear safety pin (B) so both front and
rear posts are able to come free.
b. Armrest can now be easily
removed for transferring.
C
A
4. Height-Adjustment
a. Release the upper securing lever (C).
b. Set at desired height.
c. Return securing lever to locked position.
d. Move armrest up or down to allow armrest to snap into
place.
B
I. SEAT DEPTH
The seat depth can be adjusted in one inch increments on
standard rehab seating.
1. Seat Frame Depth Adjustment
a. To adjust, loosen the two bolts (A & B) of the backrest
pivot plate on each side of the seat.
b. Reposition the backrest to the desired position.
c. Retighten bolts on each side of the backrest pivot plate.
C
D
2. Back Angle Adjustment on Seat Frame
a. Remove the front securing bolt (C) on the side of the
backrest pivot plate.
b. Loosen the lower rear bolt (D)
c. Set at desired angle. There are ten holes (in 4º increments) to choose from.
WARNING
d. Reinstall the front bolts and tighten both bolts securely.
Make sure back canes and pivot plate cannot slide out of the
side rails when in tilt position for example.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
A
B
16
IX. OPERATING GUIDE
A. CIRCUIT BREAKERS
Your Amypower Alltrack has a single circuit breaker.
 In the unlikely event of a short circuit or heavy overload, all
power to your chair will be shut off.
 To reset your chair, depress the circuit breaker button. A few
minutes wait is required before the circuit breaker will reset.
a
To access the circuit breaker

Push the battery box panel when pulling the handle.

Drop the panel down and the circuit breaker becomes
visible (a).

Reset the circuit breaker.

Lock the panel back in its upright position.
Repeated Shutdown:
If the chair continues to shut down after resetting, have it
serviced by a supplier.
B. JOYSTICK ASSEMBLY
The joystick connects to a controller, which controls the
chair’s performance. The joystick varies based on the
option selected for you.
1. VR2 Joystick *
2. R-Net (Option)*
*Please refer to the user’s manual provided with information
package.
C. ENHANCED DISPLAY
VR2
Please refer to the PG Drives Enhanced Display owner’s
manual.
R-Net
D. MOTOR LOCKS
Disconnect the motor locks when you need to manually
push the chair, for example when in an emergency, or
if batteries fail.
WARNING
1. Do not disengage motor locks unless power to the chair is
off.
2. Be aware that the chair will not have brakes in the freewheel position.
3. Make sure that the person pushing the chair has full control
when motor locks are disengaged.
A
1. To Disengage Motor Locks:
Turn the lever (A) towards the front of the chair to disengage the
motor lock.
2. To Engage Motor Locks:
Turn the lever (A) towards the center of the chair to return to the
drive position.
NOTE- If the lever is difficult to disengage, rock the wheelchair
slightly from front to rear and/or push against the chair while moving
the lever.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
17
2. R-net EL Joystick (Activates multiple power options)
E. PERFORMANCE CONTROL SETTINGS
NOTE - Seek advice regarding checking and adjusting settings.
It is vital to match control settings to your level of function and
ability.
Consult your health care professional and your supplier to select
the best control setting for you. For your safety, have the
setting of your chair verified every six months.
WARNING
Have your control settings re-adjusted immediately if you
notice any change in your ability to:
 Control the joystick.
 Avoid running into objects.
4. Control Settings can be adjusted by your dealer.
TOGGLE
PRESS
F. THERMAL ROLL-BACK
Your chair has a thermal roll back circuit. This protects the controller
from damage due to overheating. In extreme conditions (such as
repetitive hill climbing) the circuit will decrease the power to your
motors. This allows the chair to operate at a reduced speed. When
the controller cools, the chair will return to normal speed.
G. POWER SEATING OPERATION THROUGH THE JOYSTICK
The power tilt, recline, seat lift, elevating legrests or center mount
features on your chair can be operated using the joystick on your
chair.
1. 6-Key VR2 Joystick (Activates power tilt or seat lift only)
- PULL TOGGLE TO ACTIVATE OPTION
- PUSH TOGGLE TO RETURN OPTION
A. For tilt or seat lift operation through this joystick, you
must press the mode switch to access seating options.
B. Once you have accessed the seating mode of your
joystick, you must toggle left or right until the light showing
the power option you want to activate turns on.
C. Once you have accessed the seating mode in your
joystick, you must pull the toggle to activate the power
option, and push the toggle in the opposite direction to
return to the static mode.
3. R-net PM Joystick (Activates multiple power options)
PRESS
PRESS
TOGGLE
- PULL TOGGLE TO ACTIVATE OPTION
- PUSH TOGGLE TO RETURN OPTION
- PULL TOGGLE TO ACTIVATE OPTION
- PUSH TOGGLE TO RETURN OPTION
A. For tilt or seat lift operation through this joystick, you must press
the mode switch to access seating options.
B. Once you have accessed the seating mode in your joystick, you
must pull the toggle to activate the power option, and push the
toggle in the opposite direction to return to the static mode.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
A. For tilt or seat lift operation through this joystick, you
must press the mode switch to access seating options.
B. Once you have accessed the seating mode of your
joystick, you must toggle left or right until the light showing
the power option you want to activate turns on.
C. Once you have accessed the seating mode in your
joystick, you must pull the toggle to activate the power
option, and push the toggle in the opposite direction to
return to the static mode.
18
H. Power Tilt (Standard Operating Instructions)
1-
WARNING!!!
866-
Make sure the wheelchair is on a level surface before
proceeding with tilt mode.
SINGLE ACTUATOR TOGGLE SWITCH
Increasing Tilt Angle
Pull the toggle switch (located next to the wheelchair
joystick) backward toward the rear of the wheelchair until
the desired tilt angle is achieved, then release.
SINGLE ACTUATOR TOGGLE SWITCH
Decreasing Tilt Angle
To reverse the tilt angle direction. Release the toggle
switch to the neutral position for a minimum of 1 second
and push the toggle switch (located next to the wheelchair
joystick) forward toward the front of the wheelchair until
the desired tilt angle is achieved, then release.
Drive lock-Out
Is a safety feature designed to prevent the wheelchair
from being driven while in a tilt angle over 15 degrees
relative to the vertical position.
DANGER!!!
Never operate the wheelchair while in tilt mode over 15
degrees relative to the vertical position. If the drive lockout does not stop the wheelchair from operating when in a
tilt angle over 15 degrees, have the wheelchair or power
tilt system serviced by an authorized dealer or qualified
technician.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
19
I. Power Seat Lift (Standard Operating Instructions)
WARNING!!!
Make sure the wheelchair is on a level surface before
proceeding with Lift mode and driving in reduced speed
while lifted.
SINGLE ACTUATOR TOGGLE SWITCH
Increasing Lift Height
Pull the toggle switch (located next to the wheelchair
joystick) backward toward the rear of the wheelchair until
the desired Lift Height is achieved, then release.
SINGLE ACTUATOR TOGGLE SWITCH
Decreasing Lift Height
To decrease the Lift Height. Release the toggle switch to
the neutral position for a minimum of 1 second and push
the toggle switch (located next to the wheelchair joystick)
forward toward the front of the wheelchair until the desired
Lift Height is achieved, then release.
Driving in Reduced Speed
Is a feature designed to allow the user to drive the
wheelchair at a reduced speed while lifted up to 11”.
When lifted, the drive speed is then reduced to 30% of its
original setting. Full drive speed is achieved when the
seat lift is down to its lowest position.
DANGER!!!
Never operate the seat lift when the wheelchair is in any
slope. In reduced speed, the wheelchair must be driven
on a level surface relative to the vertical position. If the
reduced speed does not slow the wheelchair’s drive
speed to 30% of its original settings, have the wheelchair
or power seat lift system serviced by an authorized dealer
or qualified technician.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
20
J. Power Tilt /Seat Lift Combo (Standard Operating Instructions)
WARNING!!!
Make sure the wheelchair is on a level surface before proceeding
with either Tilt or Lift mode and driving in reduced speed while lifted.
Tilt and Seat Lift options are programmed to operate separately.
The ability to tilt while the seat lift is elevated is not possible.
Bypassing this programming may cause severe injury.
DUAL ACTUATOR TOGGLE SWITCH
Increasing / Decreasing Seat Lift Height
Pull the toggle switch (located next to the wheelchair joystick)
backward toward the rear of the wheelchair until the desired Lift
Height is achieved, then release. To change direction, release the
toggle switch to the neutral position for a minimum of 1 second, and
pull back the toggle switch in the same direction toward the back of
the chair until you achieve the desired height, then release.
DUAL ACTUATOR TOGGLE SWITCH
Increasing / Decreasing Tilt Angle Push the toggle switch
(located next to the wheelchair joystick) forward toward the front of
the wheelchair until the desired tilt angle is achieved, then release.
To change direction, release the toggle switch to the neutral
position for a minimum of 1 second, and push forward the toggle
switch in the same direction toward the front of the chair until you
achieve the desired tilt angle, then release.
Driving in Reduced Speed
Is a feature designed to allow the user to drive the wheelchair at a
reduced speed while lifted up to 11”. When lifted, the drive speed is
then reduced to 30% of its original setting. Full drive speed is
achieved when the seat lift is down to its lowest position.
Drive lock-Out
Is a safety feature designed to prevent the wheelchair from being
driven while in a tilt angle over 15 degrees relative to the vertical
position.
DANGER!!!
Never operate the wheelchair while in tilt mode over 15
degrees relative to the vertical position. Never operate the seat lift
when the wheelchair is in any slope. In reduced speed, the
wheelchair must be driven on a level surface relative to the vertical
position. If the drive lock-out does not stop the wheelchair from
operating when in a tilt angle over 15 degrees, or if it allows the seat
lift to elevate while tilted, or if the reduced speed does not slow the
wheelchair’s drive speed to 25% of its original settings, have the
wheelchair or power seat lift system serviced by an authorized
dealer or qualified technician.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
21
K. Power Recline (Std. Operating Instructions)
WARNING!!!
Make sure the wheelchair is on a level surface before
proceeding with recline mode.
Increasing Recline Angle with 4-way Toggle
Pull the four-way toggle switch back towards the rear of
the wheelchair until the desired recline angle is achieved
and release.
Increasing Recline Angle with Push Button Switches
Push the 3rd button furthest from the wire until the desired
recline angle is achieved and release.
Decreasing Recline Angle with 4-way Toggle
To reverse the recline angle direction: Release the fourway toggle switch to the neutral position for a minimum of
1 second and pull the four-way toggle switch back
towards the rear of the wheelchair until the desired recline
angle is achieved and release.
Decreasing Recline Angle with Push Button Switches
To reverse the recline angle direction: Release the 3rd
button furthest from the wire to the neutral position for a
minimum of 1 second and push the same button until the
desired recline angle is achieved and release.
Mercury Limit Switch
When equipped with a Tilt and power or manual recline
combination, your wheelchair will include a mercury
switch located inside the shroud, on the right side of the
chair. The purpose of the mercury switch is to control the
combination of the total tilt / recline angle.
This mercury switch can be manually turned to change
the total tilt / recline angle to a desired or comfortable level
for the end user. The total tilt and recline angle should
never exceed the horizontal plain (180 degrees).
Technicians must watch for a possible tilt actuator behind
the seat that would reduce the total tilt / recline limit. The
total tilt and recline angle should be limited prior to contact
between the shroud and the tilt actuator.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
22
L. Power Elevating Front Riggings (Std. Operating Instructions)
Make sure the wheelchair is on a level surface.
Increasing & Decreasing the Left Legrest Angle
With the 4-Way Toggle Switch
Move the four-way toggle switch towards the left side of the
wheelchair until the desired legrest angle is achieved. To
reverse the legrest angle direction: Release the four-way
toggle switch to the neutral position for a minimum of 1
second and move the four-way toggle switch towards the
left side of the wheelchair until the desired legrest angle is
achieved.
Increasing & Decreasing the Left Legrest Angle
With the Push Button Switches
Push the 2nd button furthest from the wire until the desired
legrests angle is achieved and release. To reverse the
legrest angle direction: Release the 2nd button furthest
from the wire to the neutral position for a minimum of 1
second and push the same button until the desired legrest
angle is achieved and release.
Make sure the wheelchair is on a level surface.
Increasing & Decreasing the Right Legrest Angle
With the 4-Way Toggle Switch
Move the four-way toggle switch towards the right side of
the wheelchair until the desired legrest angle is achieved.
To reverse the legrest angle direction: Release the fourway toggle switch to the neutral position for a minimum of 1
second and move the four-way toggle switch towards the
right side of the wheelchair until the desired legrest angle is
achieved.
Increasing & Decreasing the Right Legrest Angle
With the Push Button Switches
Push the 1st button closest to the wire until the desired
legrests angle is achieved and release. To reverse the
legrest angle direction: Release the 1st button closest to
the wire to the neutral position for a minimum of 1 second
and push the same button until the desired legrest angle is
achieved and release.
Make sure the wheelchair is on a level surface.
Increasing & Decreasing the Power Center Mount
With the 4-Way Toggle Switch
Move the four-way toggle switch towards the left side of the
wheelchair until the desired center mount angle is
achieved. To reverse the center mount angle direction:
Release the four-way toggle switch to the neutral position
for a minimum of 1 second and move the four-way toggle
switch towards the left side of the wheelchair until the
desired center mount angle is achieved.
Increasing & Decreasing the Power Center Mount
With the Push Button Switches
Push the 2nd button furthest from the wire until the desired
center mount angle is achieved and release. To reverse
the center mount angle direction: Release the 2nd button
furthest from the wire to the neutral position for a minimum
of 1 second and push the same button until the desired
center mount angle is achieved and release.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
23
M. Manual Recline (Std. Operating Instructions)
Attendant Locking Manual Recline
Attendant must pull and hold the recline lever upward in order to
release the recline locking mechanism.
Attendant Locking Manual Recline
Attendants can adjust the recline angle by either pushing down
or pulling up the rear back while pulling and holding the recline
lever activated.
Once desired recline angle is attained, release the recline lever.
User Locking Manual Lecline
User must pull and hold the release lever upward in order to
release the recline locking mechanism.
The handle can be installed on the left or right armrest
depending on user preference.
User Locking Manual Recline
User can adjust the recline angle by pulling and holding the
recline lever upward in order to release the recline locking
mechanism, then increasing or decreasing pressure on the back
to obtain desired recline angle.
Once desired recline angle is attained, release the recline lever.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
24
N. Adjustments
SEAT - Width Adjustment
Unscrew and remove the 6 to 8 screws located on top of the seat pan and, than
equally adjust the seat width to the desired width and put screws back in place.
Note: The width adjustment must also be made on the rear cross tubes that
hold the back canes and seat laterally.
WARNING: At all times, the screws holding the seat plates and back
cross tube must be screwed in tight and secured in order to avoid severe
injury and/or damage to the seating system.
SEAT - Depth Adjustment
There is two side lateral frames which will allow for depth adjustment. The short
frame is from 14” to 19” deep and the long frame is from 18” to 22” deep.
To adjust the seat depth, you must loosen the 3 screws from each side plates
and slide them to the desired seat depth.
WARNING: At all times, the three screws on each side holding the side
plates must be screwed in tight and secured in order to avoid severe
injury and/or damage to the seating system.
BACK - Adjustable Back Angle
Using the series of slotted holes provided on each side plates, increase or
decrease the back angle by loosening the screw from each side plates and
adjust them equally to the desired seat depth.
WARNING: At all times, the screws on each side holding the back canes
must be screwed in tight and secured in order to avoid severe injury
and/or damage to the seating system.
Adjusting the Center of Gravity
Due to the variety of seat measurements and modular power options available
on various power wheelchairs. Amypower offers many adjustments that allows
the ability to adjust to individual client needs, and properly adjusting the center of
gravity is critical for patient safety and wheelchair performance. To adjust the
center of gravity, unscrew the bolts on each side of the main adaptors and
adjust the system for optimal performance.
WARNING: At all times, the screws on each side holding the main system
must be screwed in tight and secured in order to avoid severe injury
and/or damage to the seating system.
WARNING: Before delivering an Amypower product, the dealer must
verify while the user is sitting in the seating system that the center of
gravity and overall stability of the wheelchair is maintained and optimal in
all combinations of tilt, recline or elevation.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
25
O. Troubleshooting Guide for Power Seating
Symptom
Possible Causes
How to fix this
NOTHING WORKS!




NO BATTERIES IN BOXES
24V POWER CABLE
DISCONNECTED
FUSE IS BURNED
SWITCHBOX IS DEFECTIVE



CHECK BATTERIES
VERIFY ALL CONNECTIONS
VERIFY AND / OR REPLACE
FUSE


DEFECTIVE ACTUATOR
MECHANICAL RESTRAINT

MAKE SURE THE SEAT IS
ALIGNED WELL AND DOESN’T
INTERFERE WITH THE REAR OF
THE TILT ACTUATOR WHEN
TILTING
CHECK FOR AND REMOVE
MECHANICAL RESTRAINTS
ELIMINATE ALL CONTACTS OF
THE ACTUATOR WITH THE
POWER BASE FRAME
ACTUATOR IS
NOISY WHEN
GOING UP OR
DOWN


ACTUATOR IS
GOING ONLY IN
ONE DIRECTION.
(WITH DAC
CONTROLLER)


RELAYS CAN BE
HEARD, BUT
ACTUATOR DOES
NOT OPERATE

FUSE BURNS
REPEATEDLY


WRONG PROGRAMMING
WRONG CABLE PLUGGING





DRIVE DEFEAT
SWITCH,
MERCURY
SWITCH OR
REDUCED SPEED
DOES NOT WORK
PROPERLY



CHARGER FUSE
BURNS EVERY
TIME I TRY TO
CHARGE THE
BATTERIES




ACTUATOR NOT
CONNECTED TO
CONTROLLER
DEFECTIVE ACTUATOR
DEFECTIVE CONTROLLER
MECHANICAL RESTRAINT
SHORT CIRCUIT IN ONE OF
THE CABLES
DEFECTIVE CONTROLLER
WRONG PROGRAMMING
WRONG CABLE PLUGGING
DRIVE DEFEAT SWITCH IS
UNPLUGGED OR DEFECTIVE
REDUCED SPEED SWITCH IS
UNPLUGGED OR DEFECTIVE
MERCURY SWITCH IS
UNPLUGGED OR
DEFECTIVE.
WRONG CHARGER IS USED
TROUBLE WITH THE POWER
INTERFACING CABLE








AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
VERIFY ELECTRICAL
ASSEMBLY AND
PROGRAMMING THOROUGHLY
IF IT STILL DOES NOT WORK,
CALL AMYPOWER TECHNICAL
SUPPORT FOR FURTHER
INSTRUCTIONS
VERIFY ELECTRICAL
ASSEMBLY AND
PROGRAMMING THOROUGHLY
IF IT STILL DOES NOT WORK,
CALL AMYPOWER TECHNICAL
SUPPORT FOR FURTHER
INSTRUCTIONS
VERIFY MECHANICAL
ASSEMBLY THOROUGHLY
CALL AMYPOWERTECHNICAL
SUPPORT FOR FURTHER
INSTRUCTIONS
VERIFY PROPER MECHANICAL
OPERATION OF LIMIT
SWITCHES.
VERIFY ELECTRICAL
ASSEMBLY AND
PROGRAMMING THOROUGHLY
IF IT STILL DOES NOT WORK,
CALL AMYPOWER TECHNICAL
SUPPORT FOR FURTHER
INSTRUCTIONS
MAKE SURE YOU ARE USING
THE BATTERY CHARGER
PROVIDED WITH YOUR
WHEELCHAIR
26
X. BATTERIES
A. INTRODUCTION
1. Notes
Batteries supply the power for your chair. They
contain a finite amount of energy and have limits on how
long they can store and supply energy.

You can charge batteries only a certain number of
times before they will fail and no longer hold a charge.

For answers to questions about batteries, consult
your supplier.
2. Use Proper Batteries:
Your chair operates on two 12 volt batteries.

They should be Group 24 (or 22NF) size with a
minimum of 50 ampere hour rating. Only deep cycle sealed
case construction batteries should be used in this device.

Connecting configuration. They should have a post
and clamp style connection.

When you buy a replacement, insist on a deep
cycle sealed case type. Do not use a car starter battery.

Group 24 batteries are a minimum requirement
for power seating.
3. Breaking In:

A battery requires “breaking-in” for the first 6 to
12 charges. It will not accept a full charge for this
period.

It is best to limit the length of your trips until you
break the batteries in and you know the range of your chair.
4. Discharged Batteries:

Never allow a battery to completely discharge. If
you operate your wheelchair until it has almost stopped,
you will greatly reduce the life of your batteries.

Never let a battery sit in a discharged condition.
Give unused or stored batteries a full charge once per
month.

Always fully charge the batteries. Avoid
“topping off ” with frequent charges.
WARNING
Never connect a life support or auxiliary device to a
wheelchair battery. The electrical system may fail, and
result in severe injury to or death of user.
B. BATTERY CHARGER
A battery charger produces a direct current (DC). When
applied to a discharged battery, this reverses the chemical
reaction that led to its discharge.
1. Charge Rate. How fast a battery will charge depends on:

Its electrical capacity; state of charge; electrolyte
temperature, and; internal condition.

The DC output of the charger. (The charge rate will
vary if the alternating current (AC) supply is higher or lower
than 110 volts).
2. Caution — To Avoid Damage to the Charger:

Never place the charger on top of a battery during
charging. (Gases from the battery can damage the
charger and may lead to an explosion or fire).

Never place a battery on top of the charger.

Never expose charger to rain or snow.
 Never unplug charger by pulling on the electrical cord.
This will damage the cord.
 Never open a charger or attempt to repair it yourself.
Return a defective charger back to your supplier.
 Keep cord out of the way, where it will not be stepped on,
tripped over, or damaged.
3. Caution — To Avoid Damage to the Battery:
 Make sure you use the correct setting for sealed (gel) batteries (located on the off-board charger).
 Never charge a frozen battery. A fully charged battery will
rarely freeze, but the fluid in a discharged battery can freeze
at 16 degrees Fahrenheit (minus 9 degrees Centigrade). If
you suspect a battery is frozen, thaw it before charging.
WARNING
Lead acid batteries generate explosive gas while charging.
Completely read and follow all warnings about the batteries
in this user instruction manual and any labels applied to the
product. Failure to do so could result in fire, explosion, injury
and/or death.
WARNING
C. ACID BURNS (unsealed wet cell batteries)
Acid in batteries is corrosive. It can cause serious burns
to the eyes and skin and can damage floors, furniture,
clothing and your wheelchair.
1. Use extreme care not to spill acid when you handle
batteries. Keep batteries upright.
2. Avoid contact of acid with bare skin or clothing.
3. Always wear rubber gloves and safety glasses
when you handle batteries.
4. If acid contacts your skin or clothing, wash immediately
with soap and water.
5. If acid contacts your eyes, immediately flood eyes with
cold running water for at least 15 minutes. Seek medical
attention immediately.
WARNING
D. CONNECTING THE BATTERIES IN THE COMPARTMENT
1. Batteries weigh up to 55 lbs. (25 kg). Take care to avoid
injury when lifting.
2. Keep batteries upright. Take care not to spill acid (wet
cell batteries).
3. Always wear rubber gloves and safety glasses when you
handle batteries.
4. Before working around batteries, remove all metal
personal effects, such as necklaces, rings, watches,
pins and other metal jewelry that might contact battery
terminal and cause a short.
WARNING
Lift batteries into battery compartment. Batteries weigh
up to 55 pounds (25 kg). Lifting batteries may cause
back strain. If you fail to heed these warnings severe
injury may occur to you.
1. Connect and disconnect battery cables with caution. Connect the red lead to the positive terminal and the black lead to
the negative terminal. Do this for each battery.
2. Tighten all terminal fasteners using two 1/2" box end
wrenches to 60 in-lbs (6.8 N.m).
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
27
PROHIBITED!
4. Place the battery compartment lid on power base.
Never make direct contact across both battery terminals, as
an explosion may occur. A spark may result in an explosion
and/or fire resulting in severe injury or death.
WARNING
E. CHARGING BATTERIES
To avoid the risk of severe injury or death from electrical
shock, fire or explosion while charging:
PROHIBITED!
Never connect charger to a 240 volt source. The main
input voltage is 110 volts.
WARNING
Never touch the charger after it is connected to an
electrical outlet. This may cause electrical shock.
 Never connect or disconnect charger from battery
while there is power to the charger.
WARNING
1. Never use an extension cord. Use of an improper cord
could damage the charger or cause a fire or electrical
shock.
2. A battery emits explosive hydrogen gas during charging.
To reduce the risk of fire or explosion:
 Make sure area is well vented. Never charge battery in a
closed-in area.
 Never smoke or allow a spark, flame or high heat near
battery during charging.
 Never allow metal tools or chair parts to make direct
contact across both battery terminals.
3. Never look directly into cells when charging battery (wet
cell batteries).
ALWAYS:
1. Use the charger that comes with your wheelchair.
Read and follow all instructions and warnings.
2. Make sure room is well ventilated.
3. Turn off all power to your chair.
4. Connect and disconnect battery cables with caution. QNOTE- Always remove and reattach the negative cable (black
cable) first.
5.
Make sure to allow enough time to fully charge
batteries.
NOTE- Batteries should never be left for long period in the
discharged state. Unused or stored batteries should be given
a charge once per month.
6. To charge batteries, use the off-board charger by
plugging off-board charger plug into the off-board
charger socket.
WARNING
F. DISPOSING OF BATTERIES
1. All batteries once they have reached the end of their useful
life are deemed to be hazardous waste.
2. For further information on handling and recycling contact
your local recycling authority.
3. Always dispose of product through a recognized agent.
XI. MAINTENANCE
A. NOTES
1. Proper maintenance will improve performance and extend
the useful life of your chair.
2. Clean your chair regularly. This will help you find loose or
worn parts and will make your chair easier to use.
3. To protect your investment, have all major service and repair work done by your supplier.
WARNING
1. Your chair needs regular maintenance for peak performance and to avoid injury from chair failure, damage or
premature wear.
2. Inspect and maintain this chair strictly per the
“Maintenance Chart”.
3. If you detect a problem, make sure to service or repair
the chair before use.
4. At least once a year, have a complete safety check and
service of your chair performed by a supplier.
B. CLEANING
1. Paint Finish:
 Clean the paint finish with mild soapy water monthly.
 Protect the paint with a coat of non-abrasive auto wax
every 6 months.
2. Motors:
 Clean around motor area weekly with a slightly damp (not
wet) cloth.
 Wipe off or blow away any fluff, dust, or dirt on or around
the motors.
NOTE- You do not need to grease or oil the chair.
3. Upholstery:
 Hand-wash only as needed. Machine washing may
damage fabric. See label instructions for information.
 Drip-dry only. Heat from a dryer may damage fabric.
NOTE- Washing the fabric may decrease fire retardant properties.
C. STORAGE TIPS
1. Store your chair in a clean, dry area. If you fail to do so,
parts may rust or corrode.
2. Before using your chair, make sure it is in proper
working order. Inspect and service all items on the
“Maintenance Chart”.
3. If you store this chair for more than three months,
have it inspected by a supplier before use.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
28
WARNING
D. BATTERY MAINTENANCE
1. To prevent an acid spill, always keep batteries upright
(wet cell batteries).
2. Never smoke or hold an open flame near batteries.
3. Always wear rubber gloves and safety glasses when
you handle batteries.
1. Maintenance Schedule:
This varies for different types of batteries. Always
follow the instructions supplied with your batteries.
NOTE- Always wear rubber gloves and safety glasses when you
handle or service batteries.
2. Adding Water: (Wet Cells Only)
• Wet-type lead acid batteries need periodic replacement
of water due to evaporation.
NOTE- Use distilled water only.
Check the battery fluid level about once a week. When you
remove the stoppers (on top of the battery) there should be
one-eighth to one-quarter of an inch of fluid above the
internal plates. Do not overfill.
3. Corrosion:
Check battery terminals often for corrosion.
a. If corrosion is present, use a wire brush to clean the
terminals. NOTE- Always wear safety glasses and rubber
gloves.
b. Use baking soda to neutralize acid.
c. Use petroleum jelly to re-grease the terminals after connecting cable to battery. (Completely cover the terminal nut
and bolt, cable clip and any exposed cable with jelly).
4. For Answers to Questions: Contact your supplier.
WARNING
E. PNEUMATIC TIRES
1. Do not use this chair if any of the tires are under- or
over-inflated.
2. Low pressure in a tire may cause the chair to veer to
one side and result in loss of control.
3. An over-inflated tire may burst.
4. Never use a gas station pump to inflate a tire. Such
pumps provide air at high volume, and may cause tire to
burst.
1. Check for signs of wear and correct air pressure in pneumatic tires weekly.
2. For best performance, inflate tires to the same pressure
level, as shown on the tire sidewall:
14" pneumatic drive wheels 35 to 45 psi (240 to 310 kpa)
3. CAUTION- To prevent tire damage:
Use a hand pump (or a low volume air pump)
to inflate tires. Use a tire gauge to check pressure.
WARNING
F. TO REPAIR OR REPLACE A TIRE
Residual air pressure in tires can cause severe
injury. Make sure you release all air in tire before
attempting to service or repair tires.
1. 6" Caster Wheels:
a. Remove caster wheel from fork using a 1/2"
wrench.
b. Make sure there is no residual air in tire before
you remove bolts that hold the two rim halves
together.
c. Remove four bolts from rim using a # 3
phillips screwdriver. Separate two halves of rim.
d. Repair or replace inner tube.
e. Reassemble the caster wheel; make sure
the bearing spacer is in place and all four bolts
are tightened to a torque of 60 in.-lbs. (6.8
N.m).
f. Mount caster wheel onto fork. Install washers correctly
tighten bolt to 240 in.-lbs. (27 N.m).
2. 14" Drive Wheels:
a. Elevate and securely support
chair so that wheel is off the
ground. Release all air from tire.
b. Remove four (4) lug nuts (A)
from rim using a socket wrench.
c. Make sure all air has been
removed from tire. Remove the
eight bolts inside the rim. Separate
two halves of rim (B).
d. Repair or replace inner tube.
Reassemble the wheel. Use a torque setting of 120 in.-lbs.
(13.5 N.m) to re- tighten bolts.
e. Inflate tire to proper pressure level (listed on
tire sidewall).
G. ORDERING PARTS
When you order parts, provide the following:
1. Model of chair
2. Serial number of chair
3. Left hand or right hand control
4. Part number, description and quantity of
parts you need.
5. State reason for replacement.
H. MAINTENANCE CHART
You should check the items on this chart at the indicated intervals. If any of the items are loose, worn, bent or distorted, immediately have them checked and/or repaired by your
authorized Amypower supplier. Frequent maintenance and
servicing will improve performance, extend wheelchair life, and
help prevent injuries.
Charge Batteries
Check tires for proper inflation
level
Check batteries for proper
electrolyte level (wet only)
Check plugs and connectors for
proper connections
Check all moving parts for wear
Inspect all nuts, bolts and fasteners
for looseness or wear
Inspect upholstery for wear
Service by authorized supplier
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
Daily Weekly Monthly Quarterly Annually
X
X
X
X
X
X
X
X
29
XII. AMYPOWER LIMITED WARRANTY
1. LIMITED WARRANTY
2. REPLACEMENT PARTS WARRANTY
Amypower warrants components of this wheelchair
against defects in materials and workmanship from the
original date of purchase from Amypower as follows:
If an item is replaced under warranty, that item’s
new warranty period shall be the greater of the
remaining original item's warranty
Warranty
Five (5) years: Base Frame, Seat Frame,
Interface Brackets, and Structural Components
One (1) year: All Electronic Components, & Actuators
(Tilt, Recline, Lift, Power Legs or center mount)
One (1) year: Motors/Gearbox
Ninety (90) days: Wheels, Upholstery, Plastic or
Rubber Parts, & Painted Surfaces
Thirty (30) days: All other Original Components
One (1) year: Base Frame, Seat Frame, Interface
Brackets, and Structural Components
Six (6) months: All Electronic Components, & Actuators (Tilt,
Recline, Lift, Power Legs or center mount)
Six (6) months: Motors/Gearbox
Thirty (30) days: Wheels, Upholstery, Plastic or
Rubber Parts, & Painted Surfaces
Thirty (30) days: All other Original Components
3. WHAT WE WILL DO
Our sole liability is to repair or replace covered parts. This is
your only remedy for consequential damages.
4. WHAT YOU MUST DO
a. Return the warranty card.
b. Obtain from us, while this warranty is in effect, prior
approval for return or repair covered parts.
c. Return the wheelchair or part(s), freight pre-paid,
C/O Amypower
178 West Service Rd
Champlain, NY
12919
d. Pay the cost of labor to install or repair parts.
5. NOTICE TO CONSUMER
There are no other express warranties. To the extent
permitted by law, any implied warranty (including a
warranty of merchantability or fitness for a particular
purpose) is limited to:
a. One (1) year from the first consumer purchase, and
b. Repair or replacement of the defective part only. This
warranty gives you certain legal rights. You may also have
other rights that vary from state to state.
AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)
30