Emerson Liebert CW User manual

Precision Cooling
For Business-Critical Continuity™
Liebert® CW™
User Manual–26-400 kW, Upflow and Downflow, 50/60Hz
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SAVE THESE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.0
LIEBERT CW NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.0
PRE-INSTALLATION GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2.1
Room Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2
Location Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3
Installing Liebert CW300 and Liebert CW400 Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4
Air Distribution—Downflow Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.5
Air Distribution—Upflow Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.6
Connections and System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.7
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.7.1
2.7.2
Cooling, Humidification and Dehumidification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.0
LIEBERT CW DIMENSIONS AND WEIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.1
Dimensions—Downflow Models with EC Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2
Dimensions—Upflow Models with EC Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3
Dimensions—Downflow Models With Centrifugal Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.4
Dimensions—Upflow Models With Centrifugal Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.5
Floor Stand Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.6
Plenum Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.0
EQUIPMENT INSPECTION AND HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.1
Packaging Material—All Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.2
Unpacking the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.2.1
4.2.2
4.2.3
4.2.4
Removing the Unit from the Skid With a Forklift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Moving the Unit to the Installation Location with Piano Jacks . . . . . . . . . . . . . . . . . . . . . . .
Removing Piano Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing Liebert CW from Skid Using Rigging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
39
39
40
5.0
EC FANS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.1
Lowering and Removing EC Fans—Downflow Units Only . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.1.1
5.1.2
5.1.3
5.2
Lowering the EC Fans into the Floor Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
EC Fan Block-Off Panel Kit—Optional. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Removing EC Fans—Downflow Units Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Installing Upflow EC Fan Plenums . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.2.1
5.2.2
Liebert CW Upflow Plenum Assembly Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Upflow Plenum and EC Fan Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6.0
ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6.1
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
i
7.0
PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
7.1
Fluid Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
7.1.1
7.1.2
7.1.3
7.2
Condensate Piping—Field-Installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Humidifier Supply Water—Optional Infrared . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Humidifier Supply Water—Optional Steam Generating Humidifier . . . . . . . . . . . . . . . . . . . 83
Chilled Water Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
7.2.1
Requirements of Systems Using Water or Glycol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
8.0
PIPING SCHEMATICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
9.0
CHECKLIST FOR COMPLETED INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
9.1
Moving and Placing Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
9.2
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
9.3
Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
9.4
Other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
10.0
INITIAL STARTUP CHECKS AND COMMISSIONING PROCEDURE FOR WARRANTY
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
10.1
Information for Warranty Inspection—Remove Power From Unit Disconnect . . . . . . . . . 100
10.2
Startup Checks With Panels Removed and Main Disconnect Off . . . . . . . . . . . . . . . . . . . . 100
10.2.1 Inspect and Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
10.3
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
10.4
Additional Considerations for Upflow Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
11.0
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
12.0
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
12.1
System Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
12.1.1 Environmental Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
12.1.2 Electric Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
12.2
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
12.3
Blower Package—Centrifugal Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
12.3.1 Fan Impellers and Bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
12.3.2 Belts—Except with EC Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
12.3.3 Electronic Variable Speed Drive (Inverter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
12.4
Blower Package—EC Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
12.4.1 Fan Impellers and Bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
12.4.2 Protective Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
12.5
Humidifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
12.5.1 Infrared Humidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
12.5.2 Cleaning Humidifier Pan and Float Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
12.5.3 Changing Humidifier Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
12.6
Steam Generating Humidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
12.7
Condensate Drain and Condensate Pump Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
12.7.1 Condensate Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
12.7.2 Condensate Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
12.8
Facility Fluid and Piping Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
ii
12.9
HVAC Maintenance Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
APPENDIX A - INSTALLING LIEBERT CW300 AND LIEBERT CW400 . . . . . . . . . . . . . . . . . . . . . . 119
COMPLIANCE WITH EUROPEAN UNION DIRECTIVES . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER
FIGURES
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Downflow unit ducting and plenum ducting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Upflow ducting configurations with centrifugal fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Plenum ducting arrangement—Upflow models with EC fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cabinet and floor planning dimensions, downflow models CW026 - CW084 with EC fans . . . . . . 9
Cabinet and floor planning dimensions, CW026, CW038 and CW041, downflow with EC
fans, front discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cabinet and floor planning dimensions, CW051, CW060, CW076 and CW084, downflow
with EC fans, front discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cabinet and floor planning dimensions, downflow models CW106 and CW114 with EC
fans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cabinet and floor planning dimensions for downflow models CW089, CW106 and CW114
with EC fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cabinet and floor planning dimensions, CW146 - CW181, downflow with EC fans, front
discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cabinet and floor planning dimensions for downflow models CW146 and CW181 with
EC fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dimensions and floor planning data downflow models CW300, CW400 with EC fans and
filter plenums . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cabinet and floor planning dimensions, upflow models CW026-CW084 with EC fans, front
air return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cabinet and floor planning dimensions, upflow models CW026 - CW084 with EC fans,
bottom air return. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cabinet and floor planning dimensions, upflow models CW106, CW114 with EC fans, front
return. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Cabinet and floor planning dimensions, upflow models CW106, CW114 with EC fans, rear
return. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cabinet and floor planning dimensions, downflow models CW106 and CW114 with
centrifugal fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cabinet and floor planning dimensions, upflow models CW026-CW084 with centrifugal
fans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cabinet and floor planning dimensions upflow models, CW106 and CW114 with
centrifugal fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Floor stand and floor planning dimensions, downflow models CW026 - CW041 with EC
fans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Floor stand and floor planning dimensions, downflow models CW076 and CW084 with
EC fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Floor stand and floor planning dimensions, downflow models CW089, CW106 and
CW114 with EC fans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Floor stand and floor planning dimensions, downflow models CW146 and CW181 with
EC fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Floor stand and floor planning dimensions—Downflow CW300 AND CW400 with EC
fans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Floor stand dimensions, optional steam, hot water reheat and humidifier piping entrances
for downflow models CW026 - CW84 with centrifugal fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Floor stand dimensions for downflow models CW106 and CW114 with centrifugal fans . . . . . . 30
Plenum dimension, CW026 - CW084 upflow plenums with EC fans. . . . . . . . . . . . . . . . . . . . . . . 31
iii
Figure 27
Figure 28
Figure 29
Figure 30
Figure 31
Figure 32
Figure 33
Figure 34
Figure 35
Figure 36
Figure 37
Figure 38
Figure 39
Figure 40
Figure 41
Figure 42
Figure 43
Figure 44
Figure 45
Figure 46
Figure 47
Figure 48
Figure 49
Figure 50
Figure 51
Figure 52
Figure 53
Figure 54
Figure 55
Figure 56
Figure 57
Figure 58
Figure 59
Figure 60
Figure 61
Figure 62
Figure 63
Figure 64
Figure 65
Figure 66
Figure 67
Figure 68
Figure 69
Figure 70
Figure 71
Figure 72
Figure 73
Figure 74
Figure 75
Figure 76
Plenum dimensions for upflow models CW026 - CW084 with centrifugal fans . . . . . . . . . . . . . .
Plenum dimensions for upflow models CW106 and CW114 with centrifugal fans . . . . . . . . . . . .
Plenum dimensions CW106, CW114 upflow plenums with EC fans . . . . . . . . . . . . . . . . . . . . . . .
Filter plenum dimensions, downflow models CW146 and CW181 with EC fans . . . . . . . . . . . . .
Equipment recommended for handling the Liebert CW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remove the unit from the skid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Moving the unit to its installation location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locate center of gravity marker and place slings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using rigging to lift Liebert CW off skid—Models CW026-CW181 . . . . . . . . . . . . . . . . . . . . . . . .
EC fan lowering procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EC fan block-off panel kit- add data from DPN002037 need to add operation in up position . . .
EC fan lowering and removal procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-grilled plenum—122" (3099mm) unit length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grilled plenum, front discharge—122" (3099mm) unit length. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grilled plenum, rear discharge—122" (3099mm) unit length . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-grilled plenum—99" (2515mm) unit length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grilled plenum, front discharge—99" (2515mm) unit length. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grilled plenum, rear discharge—99" (2515mm) unit length . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-grilled plenum—50", 74" (1270mm, 1880mm) unit length . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grilled plenum, front discharge—50", 74" (1270mm, 1880mm) unit length . . . . . . . . . . . . . . . . .
Grilled plenum, rear discharge—50", 74" (1270mm, 1880mm) unit length . . . . . . . . . . . . . . . . .
EC fan assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended tools for installing the upflow plenum and EC fan . . . . . . . . . . . . . . . . . . . . . . . .
Non-grilled plenum / Grilled plenum-front discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grilled plenum-rear discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plenum placement on top of Liebert CW unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EC fan assembly alignment for placement on top of Liebert CW unit . . . . . . . . . . . . . . . . . . . . .
EC fan assembly placement and attachment on top of Liebert CW unit. . . . . . . . . . . . . . . . . . . .
EC fan wire routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Junction box connection (fan 1 and 2 for units with 2 or 3 fans) . . . . . . . . . . . . . . . . . . . . . . . . . .
Junction box connection (Fan 3 for units with three fans / Fan 1 for single-fan units) . . . . . . . .
Front frame members for non-grilled and grilled rear-discharge plenum. . . . . . . . . . . . . . . . . . .
Grilled front-discharge plenum grille attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-grilled and grilled rear-discharge plenum front panel attachment . . . . . . . . . . . . . . . . . . . .
Grilled plenum front / rear-discharge top panel attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical field connections for downflow models CW026 - CW084 . . . . . . . . . . . . . . . . . . . . . . . .
Electrical field connections (Ethernet) for downflow models CW026 - CW084 . . . . . . . . . . . . . . .
Electrical field connections for downflow models CW089, CW106 and CW114 . . . . . . . . . . . . . .
Electrical field connections (Ethernet) for downflow models CW089, CW106 and CW114 . . . . .
Electrical field connections (high voltage) for upflow models CW026 - CW084 . . . . . . . . . . . . . .
Electrical field connections (low voltage) for upflow models CW026 - CW084 . . . . . . . . . . . . . . .
Electrical field connections (Ethernet) for upflow models CW026 - CW084 . . . . . . . . . . . . . . . . .
Electrical field connections (Ethernet) for upflow models CW106 and CW114. . . . . . . . . . . . . . .
Electrical field connections (low voltage) for upflow models CW106 and CW114 . . . . . . . . . . . . .
Electrical field connections (low voltage Ethernet) upflow models CW106 and CW114 . . . . . . .
Electrical field connections for downflow models CW146 and CW181 with EC fans . . . . . . . . . .
Gravity drain for downflow and upflow units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downflow general arrangement, CW026-CW114 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downflow general arrangement, CW181-CW146 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv
32
33
34
35
37
37
38
39
40
41
43
44
46
49
49
50
50
51
51
52
52
53
53
54
55
55
56
57
58
59
60
61
62
63
63
64
66
67
68
69
70
71
72
73
74
75
76
82
86
87
Figure 77
Figure 78
Figure 79
Figure 80
Figure 81
Figure 82
Figure 83
Figure 84
Figure 85
Figure 86
Figure 87
Figure 88
Figure 89
Figure 90
Figure 91
Figure 92
Figure 93
Figure 94
Figure 95
Figure 96
Figure 97
Figure 98
Figure 99
Primary connection locations, downflow models CW026 - CW041 with EC fans . . . . . . . . . . . . . 88
Primary connection locations, downflow models CW051 and CW060 with EC fans. . . . . . . . . . . 89
Primary connection locations, downflow models CW076 - CW084 with EC fans . . . . . . . . . . . . . 90
Primary connection locations, downflow models CW089, CW106 and CW114 with EC fans . . . 91
Primary connection locations, downflow models CW146 and CW181 with EC fans. . . . . . . . . . . 92
Primary connection locations, downflow units, model CW300 and CW400 with EC fans . . . . . . 93
Piping connections, downflow models CW026 - CW084 with centrifugal fans . . . . . . . . . . . . . . . 94
Piping connections for downflow models CW106 and CW114 with centrifugal fans . . . . . . . . . . 95
Upflow general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Piping connections for upflow models CW026 - CW084 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Piping connections for upflow models CW106 and CW114 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Correct orientation of float switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Infrared humidifier lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Steam generating humidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Run/drain switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Steam generating humidifier control board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Rear floor stand and rear unit mounted on floor stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Rear floor stand jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Floor stand bolt locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Module bolt locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Fan deck bolt locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Wire harness routing point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Wire harness junction box detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
TABLES
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Shipping dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Shipping weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Liebert CW upflow plenum with EC fan assembly(s) configurations . . . . . . . . . . . . . . . . . . . . . . 47
Key to Liebert CW Upflow plenum assembly parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Liebert CW Upflow EC fan assembly weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Maximum harmonic current distortion, IEEE-519-1992 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Typical TDD for CW106, CW114 and CW146 at 460V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Typical TDD for CW181 at 460V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Blower troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Chilled water troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Humidifier—steam generator troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Humidifier—infrared troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Reheat troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Humidifier canister part numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Faults—canister generator humidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Steam generating humidifier capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
DIP switch settings for steam generating humidifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Liebert CW300 and Liebert CW400 component parts and weights . . . . . . . . . . . . . . . . . . . . . . . 119
Table 2 - Liebert CW300 and Liebert CW400 Assembly Parts . . . . . . . . . . . . . . . . . . . . . . . . . . 120
v
vi
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important safety instructions that should be followed during the installation
and maintenance of the Liebert CW. Read this manual thoroughly before attempting to install or
operate this unit.
Only properly trained and qualified personnel should move, install or service this equipment.
Adhere to all warnings, cautions and installation, operating and safety instructions on the unit and in
this manual. Follow all operating and user instructions.
! WARNING
Arc flash and electric shock hazard. Disconnect all electric power supplies and wear protective
equipment per NFPA 70E before working within electric control enclosure. Failure to comply
can cause serious injury or death.
Customer must provide earth ground to unit, per NEC, CEC and local codes, as applicable.
Before proceeding with installation, read all instructions, verify that all the parts are included
and check the nameplate to be sure the voltage matches available utility power.
The Liebert iCOM® microprocessor does not isolate power from the unit, even in the Unit Off
mode. Some internal components require and receive power even during the Unit Off mode of
Liebert iCOM control.
The line side of the disconnect switch on the front of the unit contains live high-voltage.
The only way to ensure that there is NO voltage inside the unit is to install and open a remote
disconnect switch. Refer to unit electrical schematic.
Follow all local codes.
! WARNING
Risk of high-speed moving parts. Can cause injury or death.
Disconnect all local and remote electric power supplies before working in the unit.
Do not operate this unit with any or all cabinet panels removed.
Do not operate upflow units without installing a plenum, ductwork or guard over the blower
opening(s) on the top surface of the unit cabinet.
Ductwork must be connected to the blower(s), or a plenum must be installed on the blower
deck for protection from rotating blower wheel(s) on upflow units.
! WARNING
Risk of top-heavy unit falling over. Can cause equipment damage, injury or death.
Read all of the following instructions before attempting to move the unit, lift it, remove
packaging or prepare the unit for installation.
! CAUTION
Risk of contact with hot surfaces. Can cause injury.
The humidifiers and reheats are extremely hot during unit operation. Allow sufficient time for
them to cool before working within the unit cabinet. Use extreme caution and wear protective
gloves and arm protection when working on or near hot discharge lines, humidifiers and
reheats.
! CAUTION
Risk of sharp edges, splinters and exposed fasteners. Can cause injury.
Only properly trained and qualified personnel wearing appropriate safety headgear, gloves,
shoes and glasses should attempt to move the unit, lift it, remove packaging or prepare the
unit for installation.
1
Liebert® CW™
NOTICE
Risk of clogged or leaking drain lines. Can cause equipment and building damage.
This unit requires a water drain connection. Drain lines must be inspected regularly and
maintenance must be performed to ensure that drain water runs freely through the drain
system and that lines are clear and free of obstructions and in good condition with no visible
sign of damage or leaks. This unit may also require an external water supply to operate.
Improper installation, application and service practices can result in water leakage from the
unit. Water leakage can result in severe property damage and loss of critical data center
equipment.
Do not locate unit directly above any equipment that could sustain water damage.
Emerson recommends installing leak detection equipment for unit and supply lines.
NOTICE
Risk of a leaking coil due to freezing and/or corrosion. Can cause equipment and serious
building damage.
Cooling coils and piping systems that are connected to open cooling towers or other open
water/glycol systems are at high risk for freezing and premature corrosion. Fluids in these
systems must contain the proper antifreeze and inhibitors to prevent freezing and premature
coil corrosion. The water or water/glycol solution must be analyzed by a competent water
treatment specialist before startup to establish the inhibitor requirement. The water or
water/glycol solution must be analyzed every six months to determine the pattern of inhibitor
depletion. The complexity of water-caused problems and their correction makes it important
to obtain the advice of a water treatment specialist and follow a regularly scheduled
maintenance program.
NOTICE
Risk of overhead interference. Can cause unit and/or building damage.
The unit may be too tall to fit through a doorway while on the skid. Measure the unit and
doorway heights and refer to the installation plans to verify clearances prior to moving the
unit.
NOTICE
Risk of damage from forklift. Can cause unit damage.
Keep tines of the forklift level and at a height suitable to fit below the skid and/or unit to
prevent exterior and/or underside damage.
NOTICE
Risk of improper storage. Can cause unit damage.
Keep the Liebert CW upright, indoors and protected from dampness, freezing temperatures
and contact damage.
Liebert® CW™
2
Liebert CW Nomenclature
1.0
LIEBERT CW NOMENCLATURE
CW
026
CW = Liebert CW
Floor Mount
Chilled Water
Unit
D
C
S
D = Downflow
U = Upflow
Nominal Capacity, kW
026
038
041
051
060
076
084
089
106
114
146
181
300
400
A
A = 460/3/60
B = 575/3/60
C = 208/3/60
D = 230/3/60
2 = 380/3/60
F = 380/3/50
G = 415/3/50
M = 380-415/3/50
C = Chilled Water
S = Centrifugal Fan with Standard
Motor
V = Centrifugal Fan with Variable
Speed Drive
1 = EC Motorized Impeller
H = EC Motorized Impeller with THD
3
2
1234
A
XXXX
A-Z = Standard
configuration
S = SFA
2 = 2-Way Valve, Standard Pressure
3 = 3-Way Valve, Standard Pressure
1 = 2-Way Valve, High Pressure
T = 3-Way Valve, High Pressure
Liebert® CW™
Pre-Installation Guidelines
2.0
PRE-INSTALLATION GUIDELINES
2.1
Room Preparation
• Verify that the floor is level, solid and sufficient to support the unit. See Table 2 for unit weights.
• Confirm that the room is properly insulated and has a sealed vapor barrier.
• For proper humidity control, keep outside or fresh air to an absolute minimum (less than 5% of
total air circulated in the room).
• Do not install Liebert CW units in an alcove or at the end of a long, narrow room.
• Install the units as close as possible to the largest heat load.
• Allow at least the minimum recommended clearances for maintenance and service. See
Figures 4 through 30 for dimensions.
• Emerson recommends installing an under-floor water detection system. Contact your local Emerson representative for information.
2.2
Location Considerations
For a downflow unit, the unit can sit on an accessible, elevated flooring system. It may be necessary to
furnish additional pedestal support below the unit to ensure maximum structural support. A separate
floor stand for the unit may be used as support, independent of the elevated floor and installed prior
to the flooring system.
For downflow and upflow units, provide approximately 34" (864mm) service clearance on the left,
right and in front of the unit whenever possible. The minimum space required for service is
18" (457mm) on the left end, 18" (457mm) on the right end and 24" (610mm) in front of the unit. This
space is necessary to permit routine maintenance, such as replacing filters and adjusting the fan
speed. On downflow units and upflow CW106 and CW114 models, left- and right-end minimum
clearances are 0" (0 mm), with the exception of rear return.
Avoid installing units in an alcove or at the extreme end of a room that has a high aspect ratio (long
narrow room). Also avoid installing units too close together. This tends to reduce the effectiveness of
the air distribution as compared to units located 30-40 feet (9-12m) apart.
2.3
Installing Liebert CW300 and Liebert CW400 Units
Installing Liebert CW300 and Liebert CW400 differ from methods to install other Liebert CW units;
for details, refer to Appendix A - Installing Liebert CW300 and Liebert CW400.
2.4
Air Distribution—Downflow Units
• Verify that the raised floor has been properly sized for the unit’s airflow and the room is free of
airflow restrictions.
• Perforated floor tiles in the raised floor should ensure minimal pressure loss.
• The raised floor must provide 7-1/2" (191mm) of clearance.
• Ensure that there is adequate clearance above the unit for service, such as replacing filters.
• Optional plenums are available for downflow unit ducting.
• If installing units with electrically commutated fans (EC fans), there must be 24" minimum clearance below the unit to lower the fans. Fans may also remain the in unit if desired.
• A filter plenum is required for Liebert CW146 and CW181 units.
NOTE
The floor stand used with EC units is not symmetrical and its orientation to the Liebert CW is
critical to lowering the EC fans. Unless the floor stand is installed in the correct position, the
blowers will not lower into the floor stand.
Liebert® CW™
4
Pre-Installation Guidelines
Figure 1
Downflow unit ducting and plenum ducting
Field-Fabricated
Ductwork
Field Service Access
for filter replacement
(minimum height of
12" [305mm]; minimum
distance from unit,
2" [51mm])
Field-Fabricated
Ductwork
Provided Service
Access Door for
filter replacement
DIRECT UNIT DUCTING
Optional
Liebert
Plenum
PLENUM DUCTING
5
Liebert® CW™
Pre-Installation Guidelines
2.5
Air Distribution—Upflow Units
Various configurations are available:
• Front return
• Rear return
• Bottom return (not available on CW106 and CW114 models)
For in-room applications with supply and return grilles, several feet of clearance must be maintained
at the intake and discharge of the unit. For a bottom return, at least 6-8 inches of unrestricted underfloor height is needed.
Upflow rear-return configurations use a filter box attached to the back of the Liebert CW. Allow 25"
(635 mm) on one side of the unit for access to the rear return filter box. Refer to the filter box
installation sheet, which can be found inside the rear return filter box package.
For ducted applications, duct flanges are supplied on the blower outlets. Follow the SMACNA-Duct
Construction Standard for single-, dual-, or triple-blower systems. Do not run ductwork off the
perimeter flange on the top of the unit. This flange is for positioning and attaching the optional air
discharge plenum with grille. Attaching a duct to this flange may reduce airflow to inadequate levels.
! WARNING
Risk of high-speed moving parts. Can cause injury or death. Disconnect all local and remote
electric power supplies and make sure blowers and pulleys have stopped rotating before
working in the unit.
Do not operate upflow units without installing a plenum, ductwork or guard over the blower
opening(s) on the top surface of the unit cabinet.
Ductwork must be connected to the blower(s), or a plenum must be installed on the blower
deck for protection from rotating blower wheel(s) on upflow units.
Figure 2
Upflow ducting configurations with centrifugal fans
2
2
1
2
1
1
1 Straight section of duct off of unit to be 1.5 to 2.5 times
the longest blower dimension.
2 Typical ducting shown; ducting may run to either side.
* Follow standard practices on all duct work.
DPN001156
Rev. 0
NOTE
Drain traps are qualified to a return duct static of negative 1.5 i.w.g. (-1.5 i.w.g).
Liebert® CW™
6
Pre-Installation Guidelines
Figure 3
Plenum ducting arrangement—Upflow models with EC fans
Typical ducting shown
may run either direction.
Ducting attached
to provided plenum
flanges only.
DPN002390
Rev. 0
Follow standard practices
in all duct work.
2.6
Connections and System Setup
• Plan the routing of wiring, piping and ductwork to the unit. See Figures 63 through 73 and
Figures 75 through 87 for unit connection locations.
• The unit requires a drain, which must comply with all applicable codes. This drain line may contain boiling water. See 7.1.1 - Condensate Piping—Field-Installed for details.
• Three-phase electrical service is required for all models. Electrical service must conform to
national and local electrical codes. See the equipment nameplate for details.
• If seismic requirements apply, consult your local Emerson representative for information about a
seismic-rated floor stand.
2.7
Operating Conditions
2.7.1
Cooling, Humidification and Dehumidification
The Liebert CW must be operated in a conditioned space within the operating envelope ASHRAE
recommends for data centers: Maximum dew point of 59°F (15°C).
Operating outside this envelope can decrease equipment reliability.
Return air to the Liebert CW must be no cooler than the ASHRAE recommendation of 68°F (20°C) DB
and 40% RH or minimum WB of 54°F (12.2°C) for proper unit operation.
Operating below this can decrease equipment reliability.
Refer to ASHRAE’s publication, “Thermal Guidelines for Data Processing Environments.”
2.7.2
Heating
The Liebert CW is qualified for heating-only operation at temperatures not exceeding 80°F (27°C).
7
Liebert® CW™
Liebert CW Dimensions and Weights
3.0
LIEBERT CW DIMENSIONS AND WEIGHTS
Table 1
Shipping dimensions
Domestic Packed
in. (mm)
Export Packed
in. (mm)
026, 028, 031
55x40x76
(1400x1020x1930)
58x41x82
(1470x1040x2080)
051, 060
77x40x76
(1960x1020x1930)
80x41x82
(2030x1040x2080)
076, 084
102x40x76
(2590x1020x1930)
105x41x82
(2670x1040x2080)
089, 106, 114
125x40x80
(3180x1020x2030)
128x41x82
(3250x1040x2080)
146, 181
125x53x80
(3180x1350x2030)
128x54x82
(3250x1370x2080)
300, 400*
125x53x80
(3180x1350x2030)
128x54x82
(3250x1370x2080)
Model
1. Models CW300 and CW400 ship in two separate sections, each the size shown.
Table 2
*
Shipping weights
Model
Domestic
Packaging
lb. (kg)
Export
Packaging
lb. (kg)
026
805 (365)
1030 (467)
038
840 (381)
1065 (483)
041
890 (404)
1115 (506)
051
1135 (515)
1360 (617)
060
1200 (544)
1425 (646)
076
1380 (625)
1630 (739)
084
1480 (671)
1730 (785)
089
1800 (817)
2075 (942)
106
1950 (885)
2225 (1,009)
114
2090 (949)
2365 (1,073)
146
2900 (1,314)
3200 (1,450)
181
2900 (1,314)
3200 (1,450)
300 *
5800 (2,628)
6400 (2,900)
400 *
5800 (2,628)
6400 (2,900)
Models CW300 and CW400 ship in two separate sections,
each weighing half of the amount shown.
Liebert® CW™
8
Liebert CW Dimensions and Weights
3.1
Dimensions—Downflow Models with EC Fans
Figure 4
Cabinet and floor planning dimensions, downflow models CW026 - CW084 with EC fans
Projection of
Display Bezel
3/4" (19mm)
Overall
J
ension
Overall Dim
C
D
2"
(50.8mm)
B
Air R
etu
Air Return
Opening
A
Dimen
sio
n
2"
(50.8mm)
r n Op
Overall
Projection of
Display Bezel
3/4" (19mm)
C
inet
Unit Cab
F
Plenum
Overall
1"
(25.4mm)
ening
K
1"
(25.4mm)
72"
(1829mm)
J
on
Dimensi
A
Overall
Dimen
sio
Unit an
d Plenu n
m
1"
(25.4mm)
Air R B
eturn
Op
rn
Air Retu
Opening
ening
2"
(50.8mm)
Pre-Filter
Plenum
Shaded areas indicate
a recommended clearance
of 36" (914mm) for component
access and filter removal.
9"
(228mm)
72"
(1829mm)
1"
(25.4mm)
Un E
it B
as
e
F
it
Un
se
Ba
UNIT DIMENSIONAL DATA
1"
(25.4mm)
3"
(76.2mm)
9" (228mm)
Reheat or Humidifier Piping
Opening (Optional Steam &
G Hot Water Only)
MODELS WITH PRE-FILTERS
9"
(228mm)
H
3"
(76.2mm)
20"
(508mm)
L
M
1"
(25.4mm)
Standard Piping
E
& Electrical Opening
Fl
oo
Floor Cutout Dimensions
for Units with Centrifugal Fans
1" (25.4mm)
18"
(457mm)
rL
ev
e
E
Standard Piping
& Electrical Opening
31" (787.4mm)
Fl
oo
l
Floor Cutout Dimensions
for Units with EC Fans
Dimensions, inches (mm)
CW026
CW038
CW041
CW051
CW060
CW076
CW084
Air Discharge
Opening
20"
(508mm)
20"
(508mm)
Model
Reheat or Humidifier Piping
Opening (Optional Steam &
G Hot Water Only)
1"
(25.4mm)
Air Discharge
Opening
1" (25.4mm)
1"
(25.4mm)
F
A
B
C
D
E
50
(1270)
50
(1270)
50
(1270)
74
(1880)
74
(1880)
99
(2515)
99
(2515)
46
(1168)
46
(1168)
46
(1168)
70
(1778)
70
(1778)
95
(2413)
95
(2413)
35
(889)
35
(889)
35
(889)
35
(889)
35
(889)
35
(889)
35
(889)
32
(813)
32
(813)
32
(813)
32
(813)
32
(813)
32
(813)
32
(813)
48
(1219)
48
(1219)
48
(1219)
72
(1829)
72
(1829)
97
(2464)
97
(2464)
F
G
33
8
(883) (203)
33
8
(883) (203)
33
8
(883) (203)
33
8
(883) (203)
33
8
(883) (203)
33 15-1/4
(883) (387)
33 15-1/4
(883) (387)
H
(FC Only)
J
K
37
(940)
37
(940)
37
(940)
61
(1549)
61
(1549)
78-3/4
(2000)
78-3/4
(2000)
35-5/8
(905)
35-5/8
(905)
35-5/8
(905)
35-5/8
(905)
35-5/8
(905)
35-5/8
(905)
35-5/8
(905)
31
(787)
31
(787)
31
(787)
31
(787)
31
(787)
31
(787)
31
(787)
DPN001659
Rev. 1
rL
ev
el
Net
L
M
Weight
(EC Only) (EC Only) lb (kg)
28
(711)
28
(711)
28
(711)
51
(1295)
51
(1295)
60-3/4
(1543)
60-3/4
(1543)
2-7/8
(73)
2-7/8
(73)
2-7/8
(73)
2-7/8
(73)
2-7/8
(73)
8-7/8
(225)
8-7/8
(225)
760
(345)
795
(361)
855
(388)
1090
(494)
1115
(524)
1320
(599)
1420
(644)
Source: DPN001659, Rev. 1
9
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 5
Cabinet and floor planning dimensions, CW026, CW038 and CW041, downflow with EC fans, front
discharge
46" (1168mm)
Opening
31"
(787mm)
Opening
Customer Piping and Wiring Connections
35"
(889mm)
Return Air
Opening
33"
(838mm)
Standard bottom connections require unit to
be placed on a floor stand at least
9" (229mm) high.
If unit is to be placed directly on the
floor, an additional SFA is required to
relocate customer connections
3/4"
(19mm)
Bezel
TOP VIEW
50" (1270mm)
36"
(914mm)
72"
(1829mm)
36"
(914mm)
16"
(408mm)
29-3/4"
(754mm)
Air Discharge
Opening
FRONT VIEW
3"
(76mm)
310807
Pg. 1, Rev. 0
2"
(51mm)
48" (1219mm)
Liebert® CW™
Striated area indicates the
recommended minimum
clearance for component
access
10
Liebert CW Dimensions and Weights
Figure 6
Cabinet and floor planning dimensions, CW051, CW060, CW076 and CW084, downflow with EC
fans, front discharge
C Opening
31"
(787mm)
Opening
35"
(889mm)
33"
(838mm)
Return Air
Opening
3/4"
(19mm)
Bezel
TOP VIEW
36"
(914mm)
B
72"
(1829mm)
16"
(408mm)
F
Air Discharge
Opening
E
Air Discharge
Opening
FRONT VIEW
36"
(914mm)
Striated area indicates the
recommended minimum
clearance for component
access
16"
(408mm)
3-1/8"
(79mm)
G
D
A
310807
Pg. 2, Rev. 0
Customer Piping and Wiring Connections
Standard bottom connections require unit to
be placed on a floor stand at least
9" (229mm) high.
If unit is to be placed directly on the
floor, an additional SFA is required to
relocate customer connections
Dimensions inches (mm)
Model
A
B
C
D
E
F
G
CW051
72 (1829)
74 (1880)
70 (1778)
2.0 (51)
25.0 (636)
25.3 (643)
30.1 (764)
CW060
72 (1829)
74 (1880)
70 (1778)
2.0 (51)
25.0 (636)
25.3 (643)
30.1 (764)
CW076
97 (2464)
99 (2515)
95 (2413)
8.0 (203)
28.6 (727)
28.8 (730)
41.9 (1064)
CW084
97 (2464)
99 (2515)
95 (2413)
8.0 (203)
28.6 (727)
28.8 (730)
41.9 (1064)
11
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 7
Cabinet and floor planning dimensions, downflow models CW106 and CW114 with EC fans
G
Overall
n
Dimensio
Projection Of
Display Bezel
3/4" (19mm)
Overa
C
D
turn
Air Re g
Openin
2" (50.8mm)
A
ll Dime
nsion
B
Air R
eturn
Open
in
g
G
ll
O ve r a
sion
Dimen
2"
(50.8mm)
Projection Of
Display Bezel
3/4" (19mm)
76"
(1930mm)
1"
(25.4mm)
2"
(51mm)
A
Overall
Dim
Unit and ension
Plenum
C
abinet
Unit C
Plenum
Overall
H
turn
Air Re
g
Openin
Air Re B
turn O
pe n
ing
2"
(50.8mm)
Pre-Filter
Plenum
E
Unit Base
Shaded area indicates
a recommended
clearance of 36" (914mm)
for component access
and filter removal
9"
(228mm)
1"
(25.4mm)
F
Unit Base
76"
(1930mm)
UNIT DIMENSIONAL DATA
20"
(508mm)
Air Discharge Opening
1" (25.4mm)
77"
(1955.8mm)
Standard Piping
Opening
MODELS WITH PRE-FILTERS
26"
(660.4mm)
28"
(711mm)
*Note: "Electrical Opening" is also
used for drain connection of
optional steam generating
1" (25.4mm)
canister humidifier
E
10"
(254mm)
* Electrical
Opening
24"
(609.6mm)
1"
(25.4mm)
6" ( 1 5
16-1/4"
2.4mm (412.75mm)
)
*This drawing pertains to CW106 & CW114
with forward-curve blowers only.
DPN001660
Rev. 0
FLOOR CUTOUT DIMENSIONS
Dimensions, inches (mm)
A
B
C
D
E
F
G
H
I
Net
Weight
lb (kg)
CW106
122
(3099)
118
(2997)
35
(889)
31
(787)
120
(3048)
33
(838)
35-5/8
(905)
30
(762)
34
(864)
1785
(810)
CW114
122
(3099)
118
(2997)
35
(889)
31
(787)
120
(3048)
33
(838)
35-5/8
(905)
30
(762)
34
(864)
1925
(873)
Model
Source: DPN001660, Rev. 0
Liebert® CW™
12
Liebert CW Dimensions and Weights
Figure 8
Cabinet and floor planning dimensions for downflow models CW089, CW106 and CW114 with
EC fans
118" Opening
(2997mm)
Notes: Filters are accessible
from front of unit only.
35"
33" (889mm)
(838mm)
30-3/4"
(781mm)
Opening
Electrical connections
can be made from the
bottom of unit.
TOP VIEW
3/4"
(19mm)
Bezels
122"
(3099mm)
36"
(914mm)
24"
(610mm)
76"
(1930mm)
Striated area indicates the
recommended minimum
clearance for component access.
Shaded area indicates the
required minimum clearance
below the unit to lower the
fans. Fans may also remain
in unit if desired.
120"
(3048mm)
1-1/2"
(38mm)
FRONT VIEW
DPN001614
Rev. 1
Model
Weight
lb (kg)
CW089
1925 (873)
CW106
1785 (810)
CW114
1925 (873)
Source: DPN001659, Rev. 1
13
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 9
Cabinet and floor planning dimensions, CW146 - CW181, downflow with EC fans, front
discharge
15" (381mm)
Piping
Connections
117-3/4" (2989mm)
Opening
9-5/8"
(244mm)
42"
(1067mm)
Opening
Detail A
TOP VIEW
45"
(1143mm)
3/4" (19mm)
Bezel
18" (457mm)
Filter Plenum
94"
(2386mm)
Total Height
76"
(1930mm)
Base Unit
A
29-1/2"
(749mm)
Air Discharge
Opening
3-1/8"
(78mm)
4-5/8" (117mm)
1-1/2"
(38mm)
LEFT END
45" (1143mm)
37" (940mm)
18-7/8"
(478mm)
18-7/8"
(478mm)
27-5/8"
(700mm)
Air Discharge
Opening
30-3/4"
(779mm)
Air Discharge
Opening
36-3/8"
(924mm)
FRONT VIEW
120" (3048mm)
1"
(25mm)
18-7/8"
(478mm)
68-1/4"
(1734mm)
3-1/4"
(83mm)
1-1/2"
(38mm)
122" (3099mm)
Filter Plenum
(shipped separately
Filters are removed
through the front
of the plenum
18-7/8"
(478mm)
3-1/4"
(83mm)
48"
(1219mm)
1-1/2"
(38mm)
18-7/8"
(478mm)
30-3/4"
(779mm)
Air Discharge
Opening
27-5/8"
(700mm)
Air Discharge
Opening
36-3/8"
(924mm)
18-7/8"
(478mm)
29-1/2"
(749mm)
Air Discharge
Opening
REAR VIEW
68-1/4"
(1734mm)
Customer Piping and Wiring Connections
310807
Pg. 4, Rev. 0
Liebert® CW™
Striated area indicates the
recommended minimum
clearance for component
access
Standard bottom connections require unit to be placed
on a floor stand at least 9" (229mm) high.
If unit is to be placed on the floor, an opening is provided
in front left end panel for piping and high voltage wire routings.
Customer must drill holes in right end panel to route
low-voltage connections to standard location
(must be routed separate from any high voltage wires).
CW146 or
CW181
Base Unit
14
Liebert CW Dimensions and Weights
Figure 10 Cabinet and floor planning dimensions for downflow models CW146 and CW181 with EC fans
117-11/16" (2989mm)
Opening
45"
(1143mm)
Plenum
42"
(1067mm)
Opening
3/4"
(20mm)
BEZELS
18"
(457mm)
Filter Plenum
76"
(1930mm)
Base Unit
94"
(2388mm)
Total Height
Liebert
CW146
and CW181
45"
(1143mm)
47"
(1194mm)
120"
(3044mm)
1"
(25mm)
typical
1-1/2"
(38mm)
122"
(3099mm)
Note: Typical CW166 and CW181
with EC fans unit orientation shown.
Filter Plenum
(shipped separately)
Filters are removed
through the
front of the plenum.
Reference DPN001693
for the electrical
and plumbing
requirements.
CW146 or CW181
base unit
48"
(1219mm)
Striated area indicates
the recommended
minimum clearance
for component access.
24"
(610mm)
Shaded area indicates the required minimum clearance
below the unit to lower the fans into the floo r. Fans may
also remain in their shipped position.
Model
Weight
lb (kg)
CW146
2520 (1143)
CW181
2520 (1143)
DPN001707
Rev. 2
Source: DPN001707, Rev. 2
15
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 11 Dimensions and floor planning data downflow models CW300, CW400 with EC fans and filter
plenums
118" (2997mm)
Opening
Refer to DPN001693
for the electrical and
plumbing requirements.
For information on installing CW300
and CW400 units, refer to Appendix A Installing Liebert CW300 and Liebert
CW400
87"
(2210mm)
Opening
3/4"
(19mm)
Bezels
91" (2311mm)
1"
(25mm)
18" (457mm)
94"
(2388mm)
76"
1930mm
45"
(1143mm)
92" (2337mm)
1"
(25mm)
120" (3048mm)
1-1/2" (38mm)
122" (3099mm)
Filter Plenum
(shipped
separately)
Filters are removed
by removing front
panel of the plenum.
Two Cabinets
36"
(914mm)
48"
(1219mm)
24" (610mm)
Striated area indicates the recommended
minimum clearance for component access.
Shaded area indicates the minimum required area below
the unit to be unobstructed for the skirted floorstand
and fan service clearance.
Liebert® CW™
16
DPN002432
Rev. 0
Liebert CW Dimensions and Weights
3.2
Dimensions—Upflow Models with EC Fans
Figure 12 Cabinet and floor planning dimensions, upflow models CW026-CW084 with EC fans, front air
return
Duct flanges on plenum
top for supply air ducting when
solid panel plenum is used
B
Overall
35"
(889mm)
Overall
Projection of
Display Bezel
3/4" (19mm)
A
Plenum
1"
(25mm)
72"
(1829mm)
Unit
Return Air Grille
Supplied on
Units with Front Return
Shaded areas
indicate a recommended
clearance of 36" (914mm)
for component access
and filter removal
EC Fan
Terminal Box
C
Base
33"
(838mm)
Base
75-1/4"
(1911mm)
72"
(1829mm)
1"
(25mm)
FRONT AIR RETURN MODEL SHOWN
DPN002386
Pg. 1, Rev. 1
Left Side Detail View Without
Plenum or EC Fans
Dimensions, in. (mm)
Model
B
C
Plenum Height,
Supply Air
Dimension A
in. (mm)
CW026, CW038, CW041
50 (1270)
48 (1219)
Grille Discharge
22.75 (578)
CW051, CW060
74 (1880)
72 (1829)
Top Discharge
22.75 (578), 30 (762), 36 (914)
CW076, CW084
99 (2515)
97 (2464)
Source: DPN002836, Pg. 1, Rev. 1
17
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 13 Cabinet and floor planning dimensions, upflow models CW026 - CW084 with EC fans, bottom air
return
1"
(25mm)
REAR AIR RETURN MODEL
Return
Air Opening
A
33"
(838mm)
B
22"
(559mm)
D
C
1-1/8"
(29mm)
E
5-1/2"
(140mm)
F
Floor Cutout Dimensions
Bottom Air Return Model
Return Air Opening
Dimensions, in. (mm)
DPN002386
Pg. 2, Rev. 1
Net Weight lb (kg)
Chilled
Water
ModeL
A
B
VC
D
E
F
Unit Only
Unit w/Plenum
and Fans
CW026
44 (1118)
18 (457)
5 (127)
3 (76)
46 (1168)
48 (1219)
518 (235)
750 (340)
CW038
44 (1118)
18 (457)
5 (127)
3 (76)
46 (1168)
48 (1219)
542 (246)
774 (351)
CW041
44 (1118)
18 (457)
5 (127)
3 (76)
46 (1168)
48 (1219)
589 (267)
821 (372)
CW051
68 (1727)
20 (508)
4 (102)
3 (76)
70 (1778)
72 (1829)
755 (342)
1118 (507)
CW060
68 (1727)
20 (508)
4 (102)
3 (76)
70 (1778)
72 (1829)
827 (375)
1190 (540)
CW076
86 (2184)
18 (457)
5 (127)
6-1/2 (165)
95 (2413)
97 (2464)
1141 (518)
1566 (710)
CW084
86 (2184)
18 (457)
5 (127)
6-1/2 (165)
95 (2413)
97 (2464)
1239 (562)
1664 (755)
Source: DPN002386, Pg. 2, Rev. 1
Liebert® CW™
18
Liebert CW Dimensions and Weights
Figure 14 Cabinet and floor planning dimensions, upflow models CW106, CW114 with EC fans, front
return
35"
(889mm)
Overall
EC Fan Terminal Box
Projection of
Display Bezel
3/4" (19mm)
Note: Duct flanges on plenum
top for supply air ducting when
solid panel plenum is used.
122"
(3099mm)
Overall
A
Plenum
76"
(1930mm)
79-1/4"
(2013mm)
1"
(25mm)
76"
(1930mm)
Unit
Left Side Detail View Without
Plenum or EC Fans
Return Air Grille
Supplied on
Units With Front
Air Return
Shaded areas
indicate a recommended
clearance of 36" (914mm)
for component
access and filter removal
Front Air Return Model Shown
120"
(3048mm)
Base
DPN002387
Pg. 1, Rev. 1
19
1"
(25mm)
33"
(838mm)
Base
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 15 Cabinet and floor planning dimensions, upflow models CW106, CW114 with EC fans, rear return
24-1/4"
(616mm)
117-1/2"
(2984mm)
2-1/4"
(57mm)
22"
(559mm)
Shaded area indicates a recommended
clearance of 25" (635mm) for rear return
filter removal on one end of the unit
Net Weight, lb. (kg)
Model
Unit Only
Unit with Plenum
And Fans
CW106
1240 (562)
1827 (829)
CW114
1375 (624)
1962 (890)
Source: DPN002387, Pg. 2, Rev. 1
Liebert® CW™
20
DPN002387
Pg. 2, Rev. 1
Return Air Filter Opening
Liebert CW Dimensions and Weights
3.3
Dimensions—Downflow Models With Centrifugal Fans
Figure 16 Cabinet and floor planning dimensions, downflow models CW106 and CW114 with centrifugal
fans
G
Overall
n
Dimensio
Projection Of
Display Bezel
3/4" (19mm)
Overa
C
D
turn
Air Re g
n
e
Op in
2" (50.8mm)
A
ll Dime
nsion
B
Air R
eturn
Open
in
g
G
ll
O ve r a
n
io
s
n
e
Dim
2"
(50.8mm)
Projection Of
Display Bezel
3/4" (19mm)
76"
(1930mm)
1"
(25.4mm)
2"
(51mm)
C
a
Unit C
A
Overall
Dim
Unit and ension
Plenum
binet
Plenum
Overall
H
turn
Air Re
g
Openin
Air Re B
turn O
pe n
ing
2"
(50.8mm)
Pre-Filter
Plenum
E
Unit Base
Shaded area indicates
a recommended
clearance of 36" (914mm)
for component access
and filter removal
9"
(228mm)
1"
(25.4mm)
F
Unit Base
76"
(1930mm)
UNIT DIMENSIONAL DATA
20"
(508mm)
Air Discharge Opening
1" (25.4mm)
77"
(1955.8mm)
Standard Piping
Opening
MODELS WITH PRE-FILTERS
26"
(660.4mm)
28"
(711mm)
*Note: "Electrical Opening" is also
used for drain connection of
optional steam generating
1" (25.4mm)
canister humidifier
E
10"
(254mm)
* Electrical
Opening
24"
(609.6mm)
1"
(25.4mm)
6" ( 1 5
16-1/4"
2.4mm (412.75mm)
)
*This drawing pertains to CW106 & CW114
with forward-curve blowers only.
DPN001660
Rev. 0
FLOOR CUTOUT DIMENSIONS
Dimensions, inches (mm)
A
B
C
D
E
F
G
H
I
Net
Weight
lb (kg)
CW106
122
(3099)
118
(2997)
35
(889)
31
(787)
120
(3048)
33
(838)
35-5/8
(905)
30
(762)
34
(864)
1785
(810)
CW114
122
(3099)
118
(2997)
35
(889)
31
(787)
120
(3048)
33
(838)
35-5/8
(905)
30
(762)
34
(864)
1925
(873)
Model
Source: DPN001660, Rev. 0
21
Liebert® CW™
Liebert CW Dimensions and Weights
3.4
Dimensions—Upflow Models With Centrifugal Fans
Figure 17 Cabinet and floor planning dimensions, upflow models CW026-CW084 with centrifugal fans
35-5/8"
)
(905mm
Overall Di
Projection of
Display Bezel
3/4" (19mm)
mension
35"
)
(889mm
Overa
A
ll Dime
nsion
L
Duct Flanges on two blowers
H
1"
(25.4mm)
K
J
J
M
Front of Unit
Duct Flanges on 1 blower
72"
(1829mm)
H
K
J
Front of Unit
1" (25.4mm) Flang
for Plenum Connection
Note: Flanges
provided on
Blower(s)
outlet for
supply air
ducting.
Air grille may
be supplied on
units with front
or rear return air.
Un B
Shaded area indicates
it B
as
a recommended clearance
e
of 36" (914mm) for component
access and filter removal. Refer to
the user manual for
recommended minumum
clearance.
Unit
33" m)
8m 22"
(83
(559mm)
" )
3 3 mm
38 se 1"
8
(
a
it B (25.4mm)
Un
1"
(25.4mm)
Dimensional Data
5-1/2"
(139.7mm)
1-1/8"
(28.6mm)
D pen
O
Air Return Opening
Ai
G
e
rR
tu
Air Return
Opening
B
C
F
Fl
oo
CW026
1
CW038
1
CW041
1
CW051
2
CW060
2
CW076
2
CW084
2
ev
el
A return air grille
may be ordered in
place of the duct
flange. See specification
sheet for option supplied.
DPN001661
Rev. 1
Dimensions, inches (mm)
A
50
(1270)
50
(1270)
50
(1270)
74
(1880)
74
(1880)
99
(2515)
99
(2515)
B
48
(1219)
48
(1219)
48
(1219)
72
(1829)
72
(1829)
97
(2464)
97
(2464)
C
46
(1168)
46
(1168)
46
(1168)
70
(1778)
70
(1778)
95
(2413)
95
(2413)
D
44
(1118)
44
(1118)
44
(1118)
68
(1727)
68
(1727)
68
(1727)
68
(1727)
E
3
(76)
3
(76)
3
(76)
3
(76)
3
(76)
6-1/2
(165)
6-1/2
(165)
F
5
(127)
5
(127)
5
(127)
4
(102)
4
(102)
5
(127)
5
(127)
Source: DPN001661, Rev. 0
Liebert® CW™
rn
Models with Rear Return
rL
Models with Bottom Return
Model
g
E
Floor Cutout Dimensions
# of
Blowers
in
22
G
18
(457)
18
(457)
18
(457)
20
(508)
20
(508)
18
(457)
18
(457)
H
15-7/8
(403)
15-7/8
(403)
15-7/8
(403)
15-7/8
(403)
15-7/8
(403)
15-7/8
(403)
15-7/8
(403)
J
18-5/8
(473)
18-5/8
(473)
18-5/8
(473)
14-5/8
(371)
14-5/8
(371)
18-5/8
(473)
18-5/8
(473)
K
2-3/16
(55)
2-3/16
(55)
2-3/16
(55)
2-3/16
(55)
2-3/16
(55)
3-1/4
(82)
3-1/4
(82)
L
17-3/8
(454)
17-3/8
(454)
17-3/8
(454)
20-3/8
(517)
20-3/8
(517)
20-5/8
(524)
20-5/8
(524)
M
_
_
_
11-1/4
(286)
11-1/4
(286)
12-5/8
(321)
12-5/8
(321)
Net
Weight
lb (kg)
760
(345)
795
(361)
855
(388)
1090
(494)
1155
(524)
1320
(599)
1420
(644)
Liebert CW Dimensions and Weights
Figure 18 Cabinet and floor planning dimensions upflow models, CW106 and CW114 with centrifugal fans
122" Overall
(3099mm)
Duct Flanges on 3 Blowers
35" Overall
(889mm)
Projection of Display
Bezel 3/4" (19mm)
122" Overall
(3099mm)
32"
(813mm)
Plenum
Flange
2" (51mm)
A
B
35"
(889mm)
Ref.
D
118"
(2997mm)
Plenum Flange
E
C
C
C
E
Front of Unit
Blower Duct Flange Location
2"
(51mm)
76"
(1930mm)
Top of Unit
Blower Deck
F
76"
(1930mm) Ref.
Front or Rear Air Supply
1" (25mm) flange
for decorative
plenum alignment
Flanges provided
on blower outlets
for supply air ducting.
Air grille
supplied on
units with front
return air only
Shaded areas indicate
a recommended clearance
of 36" (914mm) for component
access and filter removal.
120" Base
(3048mm)
1"
(25mm)
33" Base
(838mm)
Unit Dimensions
Filter Access
(Both Ends)
24-1/4" (616mm)
Shaded area indicates
a recommended clearance
of 25" (635mm) for rear
return filter removal
on one end of the unit.
Air Return
Opening
117-1/2"
(2985mm)
2-1/4"
(57mm)
22" (559mm)
4" (102mm)
Duct Connections
DPN001662
Rev. 2
Models With Rear Return
Model
Blower
15 x 15
CW106
CW114
15 x 11
Dimensions, inches (mm
Supply
Motor
hp
A
B
Top Front
10-15
27-1/2 (699)
3-1/2 (89)
Top Rear
10-15
27-1/2 (699) 12-5/16 (313) 18-11/16 (475) 16-3/16 (411) 10 (254) 4-1/2 (114)
Top Front
Top Rear
10-15
30 (762)
20
10-20
C
D
E
F
18-11/16 (475) 16-3/16 (411) 10 (254) 4-1/2 (114)
3-1/2 (89)
14-3/4 (375)
16-3/16 (411) 10 (254) 4-1/2 (114)
30 (762)
3-1/2 (89)
14-3/4 (375)
16-3/16 (411) 10 (254) 4-1/2 (114)
30 (762)
12-5/16 (313)
14-3/4 (375)
16-3/16 (411) 10 (254) 4-1/2 (114)
23
Liebert® CW™
Liebert CW Dimensions and Weights
3.5
Floor Stand Dimensions
Figure 19 Floor stand and floor planning dimensions, downflow models CW026 - CW041 with EC fans
1" (25mm)
3/4"
(19mm)
14"
(356mm)
Piping access area
31-1/2"
(800mm)
3/4"
(19mm)
46-1/2" (1181mm)
Support Feet Centers
3/4"
(19mm)
48" (1219mm)
See Note 4
3/4"
(19mm) typ
33" (838mm)
7/8"
(23mm)
3" (76mm) typ
A*
49-1/2" (1257mm)
NOTES:
1) This floor stand should be used when EC fans are will be
lowered into a raised floor. The standard Liebert CW
floor stand can be used if the fans will remain in their
34-1/2" (876mm)
original, raised position.
Overall Depth
2) All paneled sides of unit overhang the floor stand by 1" (25mm).
3) The floor stand used with EC units is not symmetrical, and its orientation to the
Liebert CW is critical for lowering the EC fans. Unless the floor stand is installed in
the correct position, the blowers will not lower into the floor stand.
4) The jack and jack support are shipped loose and are intended to be placed into position
under each fan and utilized to lower or raise that fan as needed.
DPN002029
REV 0
* Leveling feet are provided with ± 1-1/2" (38mm) adjustment from nominal height “A.”
Dimension A*
Height, in (mm)
24 (610)
30 (762)
36 (914)
42 (1067)
48 (1219)
Source: DPN00209, Rev. 0
Liebert® CW™
24
Liebert CW Dimensions and Weights
Figure 20 Floor stand and floor planning dimensions, downflow models CW076 and CW084 with EC fans
25"
(635mm)
1"
(25mm)
3/4"
(19mm)
Piping access area
32"
(813mm)
Center Feet
31-1/2"
(800mm)
3/4"
(19mm)
47-3/4"
(1213mm)
95-1/2" (2426mm)
Support Feet Centers
3/4"
(19mm)
97" (2464mm)
See Note 4
7/8"
(23mm)
typ
1"
(25mm)
typ
3"
(76mm) typ
98-1/2" (2502mm)
NOTE:
1) This floor stand should be used when EC fans are intended to be lowered under
a raised floor. The standard Liebert CW floor stand can be used “if” the fans are to
remain in their original raised position.
2) All paneled sides of unit overhang floorstand 1” (25mm).
3) The floor stand used with EC units is not symmetrical and its orientation to the
Liebert CW is critical for lowering the EC fans. Unless the floor stand is installed in
the correct position, the blowers will not lower into the floor stand.
4) Jack and jack support are shipped loose and are intended to be placed into position
under each fan and utilized to lower or raise that fan as needed.
*Leveling feet are provided with ± 1-1/2” (38mm) adjustment from nominal height “A”.
33" (838mm)
A*
35" (889mm)
Overall Depth
DPN002027
Rev. 0
Dimension A*
Height, in (mm)
24 (610)
30 (762)
36 (914)
42 (1067)
48 (1219)
Source: DPN002027, Rev. 0
25
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 21 Floor stand and floor planning dimensions, downflow models CW089, CW106 and CW114 with
EC fans
1"
(25mm)
3/4"
(19mm)
20-1/4"
(514mm)
Piping access
area
31-1/2"
(800mm)
3/4"
(19mm)
32" (813mm)
Center Feet
59-1/4"
(1505mm)
118-1/2" (3010mm)
Support Feet Centers
120" (3048mm)
3/4"
(19mm)
Typ
See Note 4
1"
33"
(25mm)
(838mm)
TYP
7/8"
(22mm)
Typ
3" (76mm) TYP
121-1/2" (3086mm)
Overall Width
A*
NOTES
1. This floor stand should be used when EC fans are intended to be lowered into
the floor stand. The standard Liebert CW floor stand can be used “if” the fans
are to remain in their original raised position.
2. All paneled sides of unit overhang floorstand 1" (25mm).
3. The floor stand used with EC units is not symmetrical, and its orientation to the
Liebert CW is critical for lowering the EC fans. Unless the floor stand is installed
in the correct position, the blowers will not lower into the floor stand.
4. Jack and jack support are shipped loose and are intended to be placed into
position under each fan and utilized to lower or raise that fan as needed.
* Leveling feet are provided with ±1-1/2" (38mm) adjustment from nominal height “A.”
Liebert® CW™
26
35" (889mm)
Overall Depth
Height, in. (mm)
A*
24 (610)
30 (762)
36 (914)
42 (1067)
48 (1219)
DPN001629
Rev. 4
Liebert CW Dimensions and Weights
Figure 22 Floor stand and floor planning dimensions, downflow models CW146 and CW181 with EC fans
1"
(25mm)
20-1/4"
(514mm)
Piping access
area
3/4"
(19mm)
43-1/2"
(1105mm)
3/4"
(19mm)
44"
(1118mm)
CENTER FEET
59-1/4"
(1505mm)
3/4"
(19mm)
TYP
118-1/2"
(3010mm)
Support Feet Centers
120"
(3048mm)
See Note 4
1"
(25mm)
TYP
7/8"
(23mm)
TYP
45"
(1143mm)
A*
3" (76mm)
121-1/2" (3086mm)
Overall Depth
NOTE:
1. This floor stand should be used when EC fans are intended to be lowered into
the floor stand. The standard Liebert CW floor stand can be used if the fans
are to remain in their original, raised position.
2. All paneled sides of unit overhang floor stand 1" (25mm).
3. The floor stand used with EC units is not symmetrical, and its orientation to the
Liebert CW is critical for lowering the EC fans. Unless the floor stand is installed
in the correct position, the blowers will not lower into the floor stand.
4. The jack and jack support are shipped loose and are intended to be placed into
position under each fan and used to lower or raise one fan at a time as needed.
* Leveling feet are provided with ±1-1/2" (38mm) adjustment from nominal height†“A.”
27
47"
(1194mm)
Overall Depth
Height in (mm)
A*
24 (610)
30 (762)
36 (914)
42 (1067)
48 (1219)
DPN001696
Rev. 3
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 23 Floor stand and floor planning dimensions—Downflow CW300 AND CW400 with EC fans
NOTE:
1. This floor stand should be used when
EC fans are permitted to be lowered
into the floor stand.
2. All paneled sides of unit overhang
floor stand 1" (25mm).
3. The floor stand used with EC units
is not symmetrical and its orientation
to the Liebert CW is critical for lowering the
EC fans. Unless the floorstand is
installed in the correct position, the blowers
will not lower into the floorstand.
4. Jack and jack support are shipped loose
and are intended to be placed into position
under each fan and utilized to
lower or raise that fan as needed.
5. Hatched area for piping access.
20-1/4"
(514mm)
See Note 4
1" (25mm)
Height, in. (mm)
A*
24 (610)
30 (762)
36 (914)
42-1/4"
(1073mm)
Center of
Feet
43"
(1092mm)
* Leveling feet are provided with ±1-1/2" (38mm)
adjustment from nominal height 36" (914mm).
4"
(102mm)
See
Note 5
43"
(1092mm)
42-1/4"
(1073mm)
Center of
Feet
42 (1067)
48 (1219)
1"
(25mm)
Detail A
4"
(102mm)
90" (2287mm)
59-1/4"
(1505mm)
3/4" (19mm)
1"
(25mm)
118-1/2" (3010mm)
3/4"
(19mm)
120" (3048mm)
1" (25mm)
3" (76mm) typ.
122" (3099mm)
Overall Width
7/8"
(23mm)
A*
46"
(1169mm)
A
92" (2338mm)
Overall Depth
Liebert® CW™
DPN002433
Rev. 0
28
Liebert CW Dimensions and Weights
Figure 24 Floor stand dimensions, optional steam, hot water reheat and humidifier piping entrances for
downflow models CW026 - CW84 with centrifugal fans
1"
(25.4mm)
33"
(838mm)
3
8"
(76.2mm)
(203mm)
Optional Steam/Hot Water
Reheat or Humidifier
Piping Entrance
Location
E
A + 2" (50.8mm) =
Overall Width of Unit
Standard
piping and
electrical
entrance
location
Air Discharge
Opening
2"
(50.8mm)
D
1"
(25.4mm)
B
Length of
Vane = D - 1/8" (3mm)
Leg support supplied
on 18, 21 & 24" high models
16-1/4"
(413mm)
A
J
C
H ±1-1/2" (38mm) *
Optional Turning Vane
Field-Installed in
Fan Discharge Opening
For Rear or Front Air
Discharge
62" (1574.8mm)
* Leveling feet are provided
with ± 1-1/2" (38mm) adjustment
from nominal height H.
56-3/4" (1441.5mm)
DPN001676
Rev. 0
CROSS-BRACING LOCATION FOR 72" FRAMES ONLY
Dimensions, inches (mm)
Height in. (mm)
Overall
Unit Width
A
B
C
D
E
H* Nominal
J
CW026, CW038, CW041
50 (1270)
48 (1219)
0
0
36 (914)
8 (203)
9 (229)
6-1/2 (165)
CW051, CW060
74 (1880)
72 (1829)
0
0
60 (1524)
8 (203)
12 (305)
9 (229)
CW076, CW084
99
(2515)
97
(2464)
77-3/4
(1975)
15-1/4
(362)
15 (381)
12 (305)
18 (458)
15 (381)
21 (553)
18 (458)
24 (610)
21 (553)
Model
48-1/2 48-1/2
(1232) (1232)
Source: DPN001676, Rev. 0
29
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 25 Floor stand dimensions for downflow models CW106 and CW114 with centrifugal fans
D
K
Air Discharge
Opening
1"
(25.4mm)
A + 2" (50.8mm) =
Overall Width of Unit
E
G
Standard
Piping and
Electrical
Entrance
Location
1"
(25.4mm)
B
Leg supports
supplied on models
18", 21" and 24" high
F
A
Length Of
Vane=E-1/8"(3mm)
C
H ± 1-1/2" (38mm) *
J
Electrical
Opening
*Leveling feet are provided with ± 1 1/2" (38mm) adjustment from nominal height H.
*This drawing pertains to CW106 & CW114 with forward curve blowers only.
Optional turning vane field-installed
in fan discharge opening for rear
of front air discharge
DPN001677
Rev. 0
Dimensions, inches (mm)
Height, in. (mm)
Model
Overall Unit
Width
A
B
C
D
E
F
G
K
CW106
CW114
122
(3099)
120
(3048)
60
(1524)
60
(1524)
33
(838)
100-3/4
(2559)
16-1/4
(413)
8-1/4
(210)
11
(279)
Source: DPN001677, Rev. 0
Liebert® CW™
30
H*
Nominal
J
9 (229)
6-1/2 (165)
12 (305)
9 (229)
15 (381)
12 (305)
18 (458)
15 (381)
21 (553)
18 (458)
24 (610)
21 (533)
Liebert CW Dimensions and Weights
3.6
Plenum Dimensions
Figure 26 Plenum dimension, CW026 - CW084 upflow plenums with EC fans
Flanges provided on blower(s) outlet for
supply air ducting when
solid panel plenum is used.
D
C
1"
(25mm) 2"
(50.8mm)
1"
(25mm)
2"
(50.8mm)
20"
(508mm)
G
Both top duct openings and
front grilles are shown. See
specification sheet for specific
application.
E
A
B
F
1" (25mm)
2"
(50.8mm)
D
C
2"
(50.8mm)
1"
(25mm)
DPN002385
Rev. 1
Plenum Dimensional Data in (mm)
A
B
C
D
E
F
Grille Free
Area Sq. Ft.
(Sq. Meters)
CW026, CW038,
CW041
50
(1270)
34
(864)
46
(1168)
32
(813)
46
(1168)
2
(51)
4.29
(.40)
Grille &
Top Discharge
22.75
(578)
CW051, CW060
74
(1880)
34
(864)
70
(1778)
32
(813)
62
(1575)
6
(152)
5.85
(.54)
Top Discharge
Only
30
(762)
CW076, CW084
99
(2515)
34
(864)
95
(2413)
32
(813)
70
(1778)
14-1/2
(368)
6.83
(.63)
Top Discharge
Only
36
(914)
Model
Supply Air
G
in (mm)
Source: DPN002385, Rev. 1
31
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 27 Plenum dimensions for upflow models CW026 - CW084 with centrifugal fans
D
C
Flanges provided
on blower(s) outlet for
supply air ducting when
solid panel plenum is used.
1"
(25mm)
J
1"
(25mm)
2"
(50.8mm)
18" (457mm)
H
1"
(25mm)
E
B
A
F
1"
(25mm)
Both top duct openings and
front grilles are shown. See
specification sheet for specific
application.
D
2"
(50.8mm)
C
2"
(50.8mm)
1" (25mm)
Flange is standard on all units
except downflow models
where it must be
specified if required.
DPN001678
Rev. 1
Plenum Dimensions, in. (mm)
F
Grill Free
Area
ft2 (m2)
CW026, CW038,
50 (1270) 34 (864) 46 (1168) 32 (813) 44 (1118)
CW041
3 (76)
CW051, CW060
74 (1880) 34 (864) 70 (1778) 32 (813) 60 (1524)
7 (178)
CW076, CW084
Model
A
B
C
D
E
H
J
4.29 (.40)
20 (508)
1 (25)
5.85 (.54)
22-3/4 (578)
2-3/8 (60)
99 (2515) 34 (864) 95 (2413) 32 (813) 70 (1778) 14-1/2 (368) 6.83 (.63)
34-3/4 (883)
2-3/8 (60)
Source: DPN001678, Rev. 0
Liebert® CW™
Plenum Height in. (mm)
32
Liebert CW Dimensions and Weights
Figure 28 Plenum dimensions for upflow models CW106 and CW114 with centrifugal fans
Flanges provided
on blower(s) outlet for
supply air ducting when
solid panel plenum is used.
1" (25mm)
D
L
C
18" (457mm)
K
1"
(25mm)
G
B
Both top duct openings and
front grilles are shown. See
specification sheet for specific
application.
H
J
E
F
E
A
1" (25mm)
D
C
2" (50.8mm)
2" (50.8mm)
1" (25mm)
Flange is standard on all units
except downflow models
where it must be
specified if required.
DPN001679
Rev. 1
Plenum Dimensions, in. (mm)
Model
A
B
C
D
E
F
G
H
J
122
34
118
32
44
3-1/2
4
7
16
CW106
CW114 (3099) (864) (2997) (813) (1118) (89) (102) (178) (406)
Source: DPN001679, Rev. 0
33
Grille Free
Area, ft2 (cm2)
10.14
(.94)
Plenum Height, in.(mm)
K
L
20 (508)
1 (25)
22-3/4 (578)
2-3/8 (60)
34-3/4 (883)
2-3/8 (60)
Liebert® CW™
Liebert CW Dimensions and Weights
Figure 29 Plenum dimensions CW106, CW114 upflow plenums with EC fans
NOTE: Top duct flanges on plenum
top for supply air ducting when
solid panel plenum is used
1" (25mm)
D
C
1.5"(38mm)
20" (508mm)
J
1"
(25mm)
H
I
G
B
E
F
E
A
Both top duct opening
and grilles shown.See
spec sheet for specific
application
1" (25mm)
D
C
2" (50.8mm)
2" (50.8mm)
1"(25mm)
DPN002384
Rev. 0
Plenum Dimensions, in. (mm)
Model
A
B
C
Dt
E
F
G
H
I
CW106 122
34
118
32
44
3
2
5
18
CW114 (3099) (864) (2997) (813) (1118) (76) (51) (127) (457)
Source: DPN002384, Rev. 0
Liebert® CW™
34
Grille Free
Area Sq. Ft.
(Sq. Meters)
10.14
(.94)
Plenum Height, in. (mm)
Supply Air
J
Grille/ Top Discharge
22.75 (578)
Top Discharge Only
30 (762)
Top Discharge Only
36 (914)
Liebert CW Dimensions and Weights
Figure 30 Filter plenum dimensions, downflow models CW146 and CW181 with EC fans
117-11/16"
(2989mm) Opening
42"
(1067mm)
Opening
3/4"
(20mm)
Bezels
45"
(1143mm)
Plenum
18"
(457mm)
Filter Plenum
94"
(2388mm)
Total Height
76"
(1930mm
Base Unit
120" (3044mm)
1-1/2"
(38mm)
122" (3099mm)
1"
45"
(25mm)
(1143mm)
typ
47"
(1194mm)
Filters are removed
through the front
of the plenum
Filter Plenum
(Shipped Separately)
CW146 or
CW181 base unit
48"
(1219mm)
Striated area indicates
recommended minimum
clearance for component
access
24"
(610mm)
Shaded area indicates the minimum clearance
below the unit to lower the fans into the floor. Fans may
remain in their shipped position.
35
DPN001707
Rev. 2
Liebert® CW™
Equipment Inspection and Handling
4.0
EQUIPMENT INSPECTION AND HANDLING
Upon arrival of the unit and before unpacking it, verify that the labeled equipment matches the bill of
lading. Carefully inspect all items for damage, either visible or concealed. For initial access use a
7/32" Allen wrench for panel removal. Damage should be immediately reported to the carrier and a
damage claim filed with a copy sent to Emerson Network Power or to your sales representative.
4.1
Packaging Material—All Models
All material used to package this unit is recyclable. Please save for future use or
dispose of the material appropriately.
SAFETY INFORMATION
R
! WARNING
Risk of top-heavy unit falling over. Can cause equipment damage, injury or death.
Read all of the following instructions before attempting to move the unit, lift it, remove
packaging or prepare the unit for installation.
! WARNING
Risk of improper moving. Unit can tip over and cause equipment damage, injury or death.
Use only lifting equipment that is rated for the unit weight by an OSHA-certified rating
organization. Unit shipping weights are listed in Table 2 of this manual.
Use the center of gravity indicators (see Figure 35) on the unit to determine the position of
the slings. The center of gravity varies depending on the unit size and selected options.
The slings must be equally spaced on either side of the center of gravity indicator.
! CAUTION
Risk of sharp edges, splinters and exposed fasteners. Can cause injury.
Only properly trained and qualified personnel wearing appropriate safety headgear, gloves,
shoes and glasses should attempt to move the unit, lift it, remove packaging or prepare the
unit for installation.
NOTICE
Risk of overhead interference. Can cause unit and/or building damage.
The unit may be too tall to fit through a doorway while on the skid. Measure the unit and
doorway heights and refer to the installation plans to verify clearances prior to moving the
unit.
NOTICE
Risk of forklift running into the unit. Can cause unit damage.
Keep the tines of the forklift level and at a height to fit below the skid and unit to prevent
damage.
NOTICE
Risk of improper storage. Can cause unit damage.
Keep the Liebert CW upright, indoors and protected from dampness, freezing temperatures
and contact damage.
Liebert® CW™
36
Equipment Inspection and Handling
Figure 31 Equipment recommended for handling the Liebert CW
Forklift
Pallet
Jack
Spreader Bars and Slings
Piano Jacks
If possible, transport the Liebert CW with a forklift or pallet jacks. If that is not possible, use a crane
with slings and spreader bars.
• If using a forklift or pallet jack, make sure that the forks (if adjustable) are spread to the widest
distance that will fit under the skid.
Ensure the fork length is suitable for the unit length.
• When moving the packaged Liebert CW with a forklift, lift the unit from either end of the skid
that has the indicated labeling no higher than 4" (102mm) off the floor. Ensure that the opposite
end still touches the floor.
• The unit is to be pulled by the forklift—If the unit must be lifted higher than 4" (102mm) great
care must be exercised: Personnel who are not directly involved in moving the unit must be kept
20' (5m) or farther from the lift point of the unit.
• Always refer to the location of the center of gravity indicators when lifting the Liebert CW (see
Figure 35).
4.2
Unpacking the Unit
Remove outer packaging when ready to install the unit.
1. Remove the exterior stretch wrap packaging material from the unit, exposing the protective
corner and side packaging planks.
2. Remove the corner and side packaging planks from the unit, exposing the bag over the unit.
3. Remove the bag from the unit when ready to remove the skid and install the unit.
Figure 32 Removing packaging
Step 1
Step 2
Step 3
196713
Rev. 0
37
Liebert® CW™
Equipment Inspection and Handling
4.2.1
Removing the Unit from the Skid With a Forklift
1. Align a forklift with either the front or rear side of the unit (see Figure 33).
! WARNING
Risk of improper moving. Unit can tip over and cause equipment damage, injury or death.
Use the center of gravity indicators on the unit to determine the entry points for the tines (see
Figure 35). The center of gravity varies depending on the unit size and selected options.
The forklift’s tines must be equally spaced on either side of the center of gravity indicator. The
forklift’s tines must be locked to the widest possible spread that will fit under the unit.
2. Insert the tines of the forklift completely under the base of the Liebert CW.
! WARNING
Risk of improper moving. Unit can tip over and cause equipment damage, injury or death.
Ensure that the tines are level—not angled up or down.
The tines must be at a height that will allow proper clearance under the unit.
Ensure that the tines extend beyond the opposite side of the unit.
3. Remove the brackets holding the Liebert CW to the skid.
4. Lift the unit off the skid—no more than 4" (1052mm)—and remove the skid.
Figure 33 Remove the unit from the skid
Step 1
Step 2
Step 3
Step 4
196713
Rev. 0
Liebert® CW™
38
Equipment Inspection and Handling
4.2.2
Moving the Unit to the Installation Location with Piano Jacks
1. With the Liebert CW elevated, position piano jacks at each end of the unit (see Figure 34).
2. Lower the unit to a height suitable for the piano jacks and place protective material between the
Liebert CW and the piano jacks.
3. Secure the unit to the piano jacks and remove the forklift.
4. Use the piano jacks to move the unit for installation. At least two people are required to move the
Liebert CW with the piano jacks.
Figure 34 Moving the unit to its installation location
Step 1
Step 2
Step 3
196713
Rev. 0
4.2.3
Removing Piano Jacks
1. Lower the unit as much as the piano jacks will allow.
2. Undo all strapping holding the piano jacks to the unit.
3. Use a pry bar or similar device to lift one end of the unit just enough to allow removal of the piano
jack from that end.
4. Repeat Step 3 to remove the piano jack on the opposite end.
5. Remove all material that might have been used to protect the unit from the piano jacks and
strapping.
39
Liebert® CW™
Equipment Inspection and Handling
4.2.4
Removing Liebert CW from Skid Using Rigging
! WARNING
Risk of top heavy unit tipping over. Can cause equipment damage, injury or death.
Use only lifting equipment that is rated for the unit weight by an OSHA-certified rating
organization. Unit shipping weights are listed in Table 2 of this manual.
Use the center of gravity indicators (see Figure 35) on the unit to determine the position of
the slings. The center of gravity varies depending on the unit size and selected options.
The slings must be equally spaced on either side of the center of gravity indicator.
1. Locate the center of gravity indicator—the center of gravity varies according to a unit’s size and
options.
2. Space the slings equidistant on either side of the center of gravity indicator (see Figure 35).
Figure 35 Locate center of gravity marker and place slings
Illustration shows
rigging for one possible
center of gravity on the
Liebert CW. The center of
gravity varies with the
model’s options and size.
Slings Equidistant
from Each Side of
Indicator
Center
of Gravity
Indicator
Equal
Space
Equal
Space
196713
Rev.0
3. Place the slings between the bottom rails of the Liebert CW and the top of the skid.
NOTE
Unit is shown without packaging. These instructions may be applied with or without the outer
packaging in place, with the panels attached or with the panels removed.
4. Use spreader bars or a similar device and padding to ensure the Liebert CW will not be damaged
when the unit is lifted (see Figure 35). Lifting will force the slings toward the Liebert CW and
the slings may damage the unit unless it is properly protected.
5. Move the Liebert CW to its installation location.
6. Remove the brackets securing the Liebert CW to the shipping skid.
NOTE
Depending on final installation location, the skid may need to remain under the unit.
Therefore, the lag bolts and brackets would not yet be removed.
7. Lift the Liebert CW off the skid.
8. Move the skid from under the unit.
9. If the unit is at its installation location, lower it to the floor and remove the slings and spreader bars.
If the Liebert CW must be moved, refer to 4.2.2 - Moving the Unit to the Installation
Location with Piano Jacks.
Liebert® CW™
40
Equipment Inspection and Handling
Figure 36 Using rigging to lift Liebert CW off skid—Models CW026-CW181
196713
Rev. 0
41
Liebert® CW™
EC Fans
5.0
EC FANS
5.1
Lowering and Removing EC Fans—Downflow Units Only
Liebert CW downflow models can be equipped with EC fans that can be operated either in their fully
raised position or lowered into the floor stand for increased efficiency from reduced air resistance.
The fans are also removable, easing maintenance and replacement.
! WARNING
Risk of very heavy 145 lb. (65.7kg) fan modules dropping downward suddenly. Can cause
injury or death. Support fan modules before removing mounting hardware.
Use caution to keep body parts out of the fan modules pathway during repositioning.
Only properly trained and qualified personnel should work on this equipment.
! CAUTION
Risk of handling heavy and lengthy parts. Can cause personal injury and equipment damage.
Cabinet panels can exceed 5ft. (1.5m) in length and weigh more than 35lb. (15.9kg). Follow
relevant OSHA lifting recommendations and consider using a two-person lift for safe and
comfortable removal and installation of cabinet panels. Only properly trained and qualified
personnel wearing appropriate safety headgear, gloves and shoes should attempt to remove or
install cabinet panels.
NOTE
The Liebert CW unit should be used with the fans either in their original raised position or
with the fans in their fully lowered position. Suspension of fans in an intermediate position
will directly affect product performance and is not recommended.
5.1.1
Lowering the EC Fans into the Floor Stand
1. Remove the middle and bottom panels from the front of the unit.
2. For ease of fan lowering, Emerson recommends removing the infrared humidifier using the
approved infrared humidifier removal procedure.
3. Position the factory-supplied jack and jack support under the fan to be lowered.
4. Raise the jack to safely support the fan before removing any hardware.
NOTE
A properly positioned jack will be centered between the first and second set of tabs on the jack
support. The jack will be biased toward the front of the unit.
5. For Liebert CW models CW089-CW114, remove the two guide rails and store them; they will be
needed if the fan module is removed.
6. Cut and remove the cable tie that retains the wiring loop to the blower mounting plate. All other
cable ties that route the fan wiring should remain intact.
7. Remove the six 1/2" hex head screws, and, on CW026-CW114 models, remove the “Z” bracket(s)
using the socket wrench. Retain the hardware for later steps.
8. Using the jack, slowly lower the fan module until it rests on the frame of the unit.
NOTICE
Risk of equipment snagging cables and wiring. Can cause unit damage.
Monitor the position of the fan harnesses and other parts while lowering the fan to be sure
that they are not caught or pinched.
9. CW026, CW038, CW041, CW076 through CW114 Models: Secure the fan module in the fully
lowered position by re-installing the “Z” bracket(s), using the retained hex-head screws.
For CW051 and CW060 models, the fan module is secured to the center frame support. The “Z”
brackets will be used to secure the fan at the outer attachment point.
CW146 and CW181 models: Use the hex head screws removed in Step 7 to secure the fan
module directly to the frame. screw clearance holes are provided in the fan module
NOTE
Not all hardware retained will be used to secure the fans in the lowered positioned.
Liebert® CW™
42
EC Fans
Figure 37 EC fan lowering procedure
1
3
2
TABS
1
A
3
DETAIL A
B
B
Section
Not Shown
Jack Location
Fan Deck
3
"Z" Bracket
Location On
CW026 - CW060
Section
Not Shown
5
5
"Z" Bracket
4
Section B-B
"Z" Bracket
Location On
CW076 - CW114
Wiring Loop
TOP VIEW OF FAN DECK
DPN002037
Page 1, Rev. 5
See Step 55
DPN001625
Pg. 1, Rev. 3
43
Liebert® CW™
EC Fans
5.1.2
EC Fan Block-Off Panel Kit—Optional
The EC Fan Block-Off Panel Kit eliminates bypass airflow when EC fan are operated in the lowered
position. Refer to Figure 38 for installation.
Figure 38 EC fan block-off panel kit- add data from DPN002037 need to add operation in up position
Fasteners
Block-Off
Panel Application:
For units utilizing optional block-off kit
with fans operated in the Up position
(fans in unit).
Refer to block-off panel kit installation
instructions 301271p1 for detailed
Installation procedure.
Note: The fans must be operated in either
the fully raised position or fully lowered
position. No other fan positioning is supported.
DPN002037
Pg. 3, Rev. 5
5.1.3
Removing EC Fans—Downflow Units Only
The EC fans in Liebert CW units can be removed for easier maintenance or for replacement.
! WARNING
Risk of very heavy 145 lb. (65.7kg) fan modules dropping downward suddenly. Can cause
injury or death. Support fan modules before removing mounting hardware.
Use caution to keep body parts out of the fan modules pathway during repositioning.
Only properly trained and qualified personnel should work on this equipment.
NOTE
The Liebert CW unit should be used with the fans either in their original raised position or
with the fans in their fully lowered position. Suspension of fans in an intermediate position
will directly affect product performance and is not recommended.
Liebert® CW™
44
EC Fans
If the fan to be removed has been lowered into the floor stand, first raise the fan; if the fans are
already in the raised position, skip to Step 6. To raise a lowered fan:
1. Remove the middle and bottom panels from the front of the unit.
2. Remove the infrared humidifier to ease fan removal.
3. Remove any securing hardware and position the jack support and jack supplied with the unit
under the fan module. A properly positioned jack will be biased toward the front of the fan motor.
4. Use the jack to raise the fan module slowly out of the floor stand and into the unit.
NOTICE
Risk of equipment snagging cables and wiring. Can cause unit damage.
Monitor the position of the fan harnesses and other parts while raising the fan to be sure that
they are not caught or pinched while the fan is being raised.
5. CW089, CW106 and CW114 models: Insert the two fan guide rails supplied with the unit or
equivalent, field-supplied device into position. The rails can be installed by latching onto the
channel in the back of the unit and secured with one #8-18 x 1/2" self-threading screw in the front
channel hole provided.
CW146 and CW181 models will need to utilize a field-supplied device in place of the fan guide
rails.
6. On CW026 - CW114 models, wiring is in the rear. Unplug the power connectors to the fan
module and constrain the harness out of the way. Remove the protective shields by removing
hardware.
The CW146 and CW181 models’ wiring is in the front of the unit and does not have connectors.
The harness must be unconnected from the motor overloads in the electric panel and removed
with the fan module.
7. Remove the front vertical supports as needed to remove the fan module.
8. Using the rails, slide the blower out through the front of the unit. Reverse directions to reinstall
replacement fan module.
45
Liebert® CW™
EC Fans
Figure 39 EC fan lowering and removal procedure
2
See Step 3
See Steps 1 and 2
3
6
6
8
7
5
See Step 8
See Steps 4 - 7
Liebert® CW™
46
EC Fans
5.2
Installing Upflow EC Fan Plenums
Liebert CW upflow models CW026 to CW114 may be ordered with optional EC fans instead of upflow
centrifugal fans. EC fans must be installed in a separate plenum.The installation instructions for
these units is contained in the fan module, which is shipped separately from the main unit. Follow all
instructions to reduce the risk of damage to property, personnel and equipment.
Installation instructions begin at 5.2.2 - Upflow Plenum and EC Fan Preparation
! WARNING
Risk of electrical shock. Can cause injury or death. Disconnect all local and remote electric
power supplies before working within.
Risk of mishandling heavy fan assembly(s) and plenum. Can cause equipment damage,
injury, or death. Attach the fan assembly(s) and plenum to the unit only as described in these
instructions.
! CAUTION
Risk of sharp edges and heavy parts. Can cause injury and equipment damage.
A minimum of two properly trained and qualified personnel are required to install the fan
assembly(s) and plenum.
Wear OSHA approved safety headgear, gloves, shoes, and glasses when installing the fan
assembly(s) and plenum.
Equipment used in handling/lifting, and/or installing the fan assembly(s) and plenum must
meet OSHA requirements. Use handling/lifting equipment rated for the weight of the fan
assembly(s) and plenum. Use ladders rated for the weight of the fan assembly(s) and plenum
and technicians if used during installation.
Refer to handling/lifting, and/or installation equipment operating manual for manufacturer's
safety requirements and operating procedures.
Refer to Figure 3 for plenum weight, table 2 for fan assembly weight.
Table 3
Liebert CW upflow plenum with EC fan assembly(s) configurations
Plenum Height
24" (610 mm)
Unit Description
30" (762 mm)
36" (917 mm)
Assembly Number and Weight
CW106-114 Unit Length 122" (3099mm)
Non-grilled plenum
305211G1 - 150lb. (68kg)
305211G2 - 181lb. (82kg)
305211G3 - 207lb. (94kg)
Front discharge
306584G1 - 281lb. (127kg)
—
—
Rear discharge
305468G1 - 281lb. (127kg)
—
—
CW076-084 Unit Length 99" (2515mm)
Non-grilled plenum
306085G1 - 124lb. (56kg)
306085G2 - 148lb. (67kg)
306085G3 - 168lb. (76kg)
Front discharge
306585G1 - 221lb. (100kg)
—
—
Rear discharge
306082G1 - 221lb. (100kg)
—
—
306205G2 - 119lb. (54kg)
306205G3 - 137lb. (62kg)
CW051-060 Unit Length 74" (1880mm)
Non-grilled plenum
306205G1 - 99lb. (45kg)
Front discharge
306586G1 - 159lb. (72kg)
—
—
Rear discharge
306204G1 - 159lb. (72kg)
—
—
CW026-041 Unit Length 50" (1270mm)
Non-grilled plenum
306194G1 - 75lb. (34kg)
306194G2 - 91lb. (41kg)
306194G3 - 104lb. (47kg)
Front discharge
306587G1 - 130lbs. (59kg)
—
—
Rear discharge
306193G1 - 130lbs. (59kg)
—
—
47
Liebert® CW™
EC Fans
Table 4
5.2.1
Liebert CW Upflow EC fan assembly weight
Assembly Number and Weight
Voltage
306943G1 - 102lb. (46kg)
480V
306943G2 - 102lb. (46kg)
208V
Liebert CW Upflow Plenum Assembly Parts
Refer to Figures 40 through 48. Not all parts are used for all models.)
Table 5
Item
Key to Liebert CW Upflow plenum assembly parts
Description
Quantity
1
Side Panel
2
2
Front Solid Panel
1
3
Front Grilled Panel
1
4
Short Front Solid Panel
1
5
Short Front Grilled Panel
1
6
Short Rear Solid Panel
1
7
Short Rear Grilled Panel
1
8
Front / Rear Solid Panel
1
9
Rear Grilled Panel
1
10
Angle Top Rear
1
11
Channel Panel
1 or 2
12
Panel Mounting Bracket (double panel)
1
13
Top Frame
1
14
Top Frame Extension
1
15
Top Frame Angle Brace
1
16
Top Panel (with holes)
1
17
Top Panel (plain)
1
18
Plenum Brace
1
19
Panel Mounting Bracket (single panel)
1
20
Washer
21
Bolt
22
Channel Frame
23
Sheet Metal Screw
Liebert® CW™
Varies
Depending
on Assembly
48
EC Fans
Figure 40 Non-grilled plenum—122" (3099mm) unit length
10
KEY TO COMPONENTS
1 - Side Panel
2 - Front Solid Panel
4 - Short Front Solid
Panel
6 - Short Rear Solid Panel
8 - Front / Rear Solid
Panel
10 - Angle Top Rear
11 - Channel Panel
12 - Panel Mounting
Bracket (double
panel)
13 - Top Frame
14 - Top Frame Extension
15 - Top Frame Angle
Brace
18 - Plenum Brace
20 - Washer
21 - Bolt
22 - Channel Frame
6
1
Refer to Table 5 for key
to component locations.
8
14
11
20 21
18
15
13
22
22
4
12
2
1
20 21
20
19 21
20 21
Figure 41 Grilled plenum, front discharge—122" (3099mm) unit length
Refer to Table 5 for key to component locations.
17
16
6
1
KEY TO COMPONENTS
1 - Side Panel
3 - Front Grilled Panel
5 - Short Front Grilled Panel
6 - Short Rear Solid Panel
8 - Front / Rear Solid Panel
11 - Channel Panel
16 - Top Panel (with holes)
17 - Top Panel (plain)
8
11
11
5
3
1
49
Liebert® CW™
EC Fans
Figure 42 Grilled plenum, rear discharge—122" (3099mm) unit length
Refer to Table 5 for key
to component locations.
KEY TO COMPONENTS
1 - Side Panel
2 - Front Solid Panel
4 - Short Front Solid Panel
7 - Short Rear Grilled Panel
9 - Rear Grilled Panel
11 - Channel Panel
12 - Panel Mounting Bracket
(double panel)
13 - Top Frame
14 - Top Frame Extension
15 - Top Frame Angle Brace
16 - Top Panel (with holes)
17 - Top Panel (plain)
19 - Panel Mounting Bracket
(single panel)
20 - Washer
21 - Bolt
22 - Channel Frame
17
16
7
1
14
11
9
20 21
13
15
22
4
22
12
20
2
1
20 21
21
19 20 21
Figure 43 Non-grilled plenum—99" (2515mm) unit length
18
1
Refer to Table 5 for key
to component locations.
13
8
20 21 22
2
1
19
Liebert® CW™
20
21
50
KEY TO COMPONENTS
1 - Side Panel
2 - Front Solid Panel
8 - Front / Rear Solid Panel
13 - Top Frame
18 - Plenum Brace
19 - Panel Mounting Bracket
(single panel)
20 - Washer
21 - Bolt
22 - Channel Frame
EC Fans
Figure 44 Grilled plenum, front discharge—99" (2515mm) unit length
KEY TO COMPONENTS
1 - Side Panel
3 - Front Grilled Panel
8 - Front / Rear Solid Panel
16 - Top Panel (with holes)
17 - Top Panel (plain)
17
Refer to Table 5 for key
to component locations.
16
1
8
3
1
Figure 45 Grilled plenum, rear discharge—99" (2515mm) unit length
Refer to Table 5 for key
to component locations.
17
16
1
KEY TO COMPONENTS
1 - Side Panel
2 - Front Solid Panel
9 - Rear Grilled Panel
13 - Top Frame
16 - Top Panel (with holes)
17 - Top Panel (plain)
19 - Panel Mounting
Bracket (single panel)
20 - Washer
21 - Bolt
22 - Channel Frame
9
13
20 21 22
2
19
20
21
1
51
Liebert® CW™
EC Fans
Figure 46 Non-grilled plenum—50", 74" (1270mm, 1880mm) unit length
1
Refer to Table 5 for key
to component locations.
KEY TO COMPONENTS
1 - Side Panel
2 - Front Solid Panel
8 - Front / Rear Solid Panel
13 - Top Frame
20 - Washer
21 - Bolt
22 - Channel Frame
8
13
2
20 21 22 Not used on 50" unit
1
Figure 47 Grilled plenum, front discharge—50", 74" (1270mm, 1880mm) unit length
16
Refer to Table 5 for key
to component locations.
1
8
3
1
Liebert® CW™
52
KEY TO COMPONENTS
1 - Side Panel
3 - Front Grilled Panel
8 - Front / Rear Solid Panel
16 - Top Panel (with holes)
EC Fans
Figure 48 Grilled plenum, rear discharge—50", 74" (1270mm, 1880mm) unit length
16
Refer to Table 5 for key
to component locations.
1
KEY TO COMPONENTS
1 - Side Panel
2 - Front Solid Panel
9 - Rear Grilled Panel
13 - Top Frame
16 - Top Panel (with holes)
20 - Washer
21 - Bolt
22 - Channel Frame
13
9
2
20 21 22 Not used on 50" unit
1
Figure 49 EC fan assembly
Washer and
Bolt
Number of fans depends on unit size
Spacer
EC Fan Assembly
Spacer
Washer and
Bolt
Spacer
Washer and
Bolt
Spacer
306970
Pg. 9, Rev. 0
Washer and
Bolt
Spacer
5.2.2
Upflow Plenum and EC Fan Preparation
Grilled plenums are intended for Liebert CW upflow units only. Non-grilled plenums provide access
for installing and servicing EC fan assembly(s) on upflow units with field-supplied ductwork.
1.
2.
3.
4.
Move the Liebert CW to the installation location and remove items from packaging.
Verify that the fan motor(s) voltage rating is appropriate for the marked unit voltage rating.
Disconnect all local and remote power to the unit.
Emerson recommends using a lifting device, such as a duct lift or scissors lift, to assist in
installing the EC fan assembly(s) on top of the Liebert CW unit.
53
Liebert® CW™
EC Fans
Figure 50 Recommended tools for installing the upflow plenum and EC fan
For Steps 1 through 3, refer to Figure 40 (for non-grilled plenum) or to Figure 41 (grilled plenum)
(items from Table 5).
1. Attach Items 6 (short front solid panel) and 8 (front/rear solid panel) together using Item 11
(channel panel) and (10) Item 23 (sheet metal screw).
2. Attach (2) Item 1 (side panel) to assembled Items 6 and 8 using (10) Item 23. See Detail “A” for
placement of Item 23.
3. Attach Item 10 (angle top rear) to assembled Items 6 and 8 using (6) Item 23 (only on non-grilled
plenum).
For Steps 4 through 5, refer to Figure 52; items from Table 5.
4. Attach Items 7 (short rear grilled panel) and 9 (rear grilled panel) together using Item 11
(channel panel) and (10) Item 23 (sheet metal screw).
5. Attach (2) Item 1 (side panel) to assembled Items 7 and 9 using (10) Item 23. See Detail “A” in
Figure 51 for placement of Item 23.
Liebert® CW™
54
EC Fans
Figure 51 Non-grilled plenum / Grilled plenum-front discharge
KEY TO COMPONENTS
1 - Side Panel
6 - Short Rear Solid Panel
8 - Front / Rear Solid Panel
10 - Angle Top Rear
11 - Channel Panel
23 - Sheet Metal Screw
1
10 23
23
6
11
23
Detail A
Detail A
Insulation on panel
must be pushed in
to access screw holes.
8
1 23
Figure 52 Grilled plenum-rear discharge
1
23
7
KEY TO COMPONENTS
1 - Side Panel
7 - Short Rear Grilled Panel
9 - Rear Grilled Panel
11 - Channel Panel
23 - Sheet Metal Screw
23
11
Detail A
Detail A
Insulation on panel
must be pushed in
to access screw holes.
9
1
23
For Steps 6 through 8, refer to Figure 53; items from Table 5.
6. Lift assembled panels from Step 1 or Step 5, and place on top of Liebert CW unit.
7. Make sure all of the assembled panels are snug against the collar flange on top of the Liebert CW
unit.
8. Attach the assembled panels to the collar flange using Item 23 (sheet metal screws).
Emerson recommends using clamps to hold the panels snug to the collar flange while inserting
the screws.
55
Liebert® CW™
EC Fans
Figure 53 Plenum placement on top of Liebert CW unit
Detail B
Clamp Reference
(use as many
as needed)
Detail B
For Steps 9 through 11, refer to Figure 54.
9. Place the EC fan assembly onto the lifting device (duct lift shown as one option for lifting the EC
fan assembly).
10. Orient the lifting device so that it is in line with where the EC fan assembly is to be installed.
11. Lift the EC fan assembly to just above the top of Liebert CW unit. Make sure not to damage the
unit panels or the installed plenum panels
Liebert® CW™
56
EC Fans
Figure 54 EC fan assembly alignment for placement on top of Liebert CW unit
For Steps 12 through 14, refer to Figure 56; items from Table 5.
12. With the EC fan assembly lifted to clear the top of the Liebert CW unit, one person is to be on
each side of the assembly. It is recommended by Liebert that additional personnel is used to assist
in ladder stabilization.
13. Using the handles, slide the EC fan assembly onto the top of the Liebert CW unit. Slide the
assembly until the mounting holes on the assembly base aligns with the threaded locations on top
of the Liebert CW unit. (Note: the assembly will need to be lifted over the hinge which is along the
top of the Liebert CW unit.)
14. Attach the EC fan assembly using (6) Item 2 (washer), Item 3 (bolt), and Item 4 (spacer).
15. Repeat Steps 9 through 14 for each fan assembly to be installed.
57
Liebert® CW™
EC Fans
Figure 55 EC fan assembly placement and attachment on top of Liebert CW unit
Repeat Steps 3 and 4
for each fan assembly
to be installed.
2 3
2
3
KEY TO COMPONENTS
2 - Front Solid Panel
3 - Front Grilled Panel
For Steps 16 through 22, refer to Figure 56.
16.
17.
18.
19.
20.
Route wire harnesses from EC fans as indicated.
Existing wire ties holding the harnesses to the fan cage may require removal.
Black sleeved wire harnesses contain wires for fan control.
Gray sleeved wire harnesses contain wires for motor high volt connection.
Insert wire harnesses into the indicated openings of the junction boxes. Make sure not to route
the wiring over the handles of the EC fan assembly.
21. Refer to Figures 57 and 58 for wire connections inside the junction box.
22. Use provided wire ties to secure the wire harnesses to the fan cage to prevent the wire harnesses
from moving when the fans are functioning
Liebert® CW™
58
EC Fans
Figure 56 EC fan wire routing
See Figure 57
See Figure 58
NOTICE
Risk of pinched wiring. Can cause short circuit and/or loss of power to fans.
Make sure all connected wires are within the junction box prior to closing and securing the
lid.
59
Liebert® CW™
EC Fans
Figure 57 Junction box connection (fan 1 and 2 for units with 2 or 3 fans)
Fan
(low-voltage)
Fan
(low-voltage)
BL
BL
OR
OR
R
BK
R
SHLD
BK
SHLD
Green/Yellow
Ground Wire
3
2
1
3
2
3
3
2
2
1
1
1
Typical Both Fans
Motor HV
(high-voltage)
Liebert® CW™
Motor HV
(high-voltage)
60
NOTE: The wire termination torque for the high-volt
terminal blocks is 16-20 in-lb.
EC Fans
Figure 58 Junction box connection (Fan 3 for units with three fans / Fan 1 for single-fan units)
Fan
(Low-Voltage)
SHLD Wire
from Unit Harness
BL
OR
R
BK
SHLD
Green/Yellow
Ground Wire
3
3
2
2
1
1
3
2
1
The wire termination torque
for the high-voltage terminal
is 16-20 in/lb.
Motor HV
(High-Voltage)
For Steps 23 through 27, refer to Figure 59; items from Table 5)
23. Attach Item 12 (panel mounting bracket) to the Liebert CW unit top. Use (2) Item 20 (washer) and
Item 21 (bolt) for attachment.
24. Attach Item 13 (top frame) to Item 14 (top frame) using Item 15 (top frame angle brace) and (4)
Item 23 (sheet metal screw).
25. Attach Items 22 (channel frame) to assembled Items 13, 14, and 15. Use (2) Item 23 (sheet metal
screw) for each Item 22.
26. Attach assembled Items 13, 14, 15, and 22 through Item 22 to the top of the Liebert CW unit. Use
(1) Item 20 (washer) and Item 21 (bolt) for each Item 22.
27. Attach assembled frame to the side panels of the plenum. Use (2) Item 23 (sheet metal screw) for
each side panel attachment.
61
Liebert® CW™
EC Fans
Figure 59 Front frame members for non-grilled and grilled rear-discharge plenum
13 141523
KEY TO COMPONENTS
12 - Panel Mounting Bracket
(double panel)
20 - Washer
21 - Bolt
12
20
21
20
21
22
21
20 22
28. Attach Item 3 (front grilled panel) and Item 5 (short front grilled panel) together using Item 11
(channel panel) and (10) Item 23 (sheet metal screw). Refer to Figure 60; items from Table 5.
29. Attach assembled Items 3 and 5 to previously placed plenum side panels. Use (10) Item 23 (sheet
metal screw), (5) per side. Refer to Figure 60; items from Table 5.
30. Attach Item 2 (front solid panel) and Item 4 (short front solid panel) to previously placed front
frame using dzus fasteners installed in Item 2 and 4. Refer to Figure 61; items from Table 5.
Liebert® CW™
62
EC Fans
Figure 60 Grilled front-discharge plenum grille attachment
KEY TO COMPONENTS
3 - Front Grilled Panel
5 - Short Front Grilled Panel
11 - Channel Panel
23 - Sheet Metal Screw
11
23
5
23
3
23
Figure 61 Non-grilled and grilled rear-discharge plenum front panel attachment
KEY TO COMPONENTS
2 - Front Solid Panel
4 - Short Front Solid Panel
4
2
31. Attach Item 16 (top panel w/holes) and item 17 (top panel plain) to the top of previously placed
plenum panels. Use (39) Item 23 (sheet metal screw). Refer to Figure 62; items from Table 5.
63
Liebert® CW™
EC Fans
Figure 62 Grilled plenum front / rear-discharge top panel attachment
17
23
KEY TO COMPONENTS
17 - Top Panel (plain)
23 - Sheet Metal Screw
16 23
Liebert® CW™
64
Electrical Connections
6.0
ELECTRICAL CONNECTIONS
6.1
Electrical Connections
Three-phase electrical service is required for all models. Electrical service must conform to national
and local electrical codes. Refer to equipment nameplate regarding wire size and circuit protection
requirements. Refer to electrical schematic when making connections. Refer to Figures 63
through 73 for electrical service entrances into unit.
A manual electrical disconnect switch should be installed in accordance with local codes and
distribution system. Consult local codes for external disconnect requirements.
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect local and remote power supplies
before working within.
Use voltmeter to make sure power is turned off before making any electrical connections.
Before proceeding with installation, read all instructions, verify that all the parts are included
and check the nameplate to be sure the voltage matches available utility power.
50Hz Models Only: Reinstall all terminal covers before connecting power to the unit. Failure
to install these covers exposes high-voltage terminals.
Follow all local codes.
! WARNING
Risk of improper wiring, piping, moving, lifting and handling. Can cause equipment damage,
injury or death.
Installation and service of this equipment should be done only by personnel who have been
properly trained and qualified in the installation of air conditioning equipment
! WARNING
Risk of overheated electrical connection terminals. Can cause equipment damage, smoke and
activation of smoke alarm and fire suppression system that can lead to injuries or death from
building evacuation accidents.
Use copper wiring only. Make sure that all connections are tight.
NOTICE
Risk of improper electrical supply connection. Can cause equipment damage.
See the transformer label for primary tap connections. The installer must change the
transformer primary taps if the applied unit voltage is other than the pre-wired tap voltage.
65
Liebert® CW™
Electrical Connections
Figure 63 Electrical field connections for downflow models CW026 - CW084
Field-supplied disconnect switch when factory-installed
unit disconnect switch is not provided. Select per national
and local codes.
Factory-installed unit disconnect switch (optional)
Monitoring Panel
Three-phase connection (50Hz). Electric service
connection terminals when factory disconnect
switch is NOT supplied
Earth ground connection (60Hz).
Connection terminal for field-supplied
earth grounding wire.
Three-phase electric service
not by Emerson.
Three-phase connection. Electric
service connection terminals when
factory disconnect switch is supplied.
Earth ground bar (on 50Hz only).
Connection terminals with factory ground
from each high-voltage component for
field-supplied earth grounding wire.
Main fuse block and fuses not
present when fused disconnect installed
or on 50Hz units
Three-phase connection (60Hz). Electric service
connection point when factory disconnect
switch is NOT supplied
2 3
Factory-installed disconnect switch (optional).
May be fused disconnect with internal fuses.
Liebert IntelliSlot Housings. Optional monitoring and
communication cards inserted here.
Special alarm connections. Field-supplied
24V. Class 2 wire for special alarms.
Three-phase electric service not by Emerson
Electric conduit knockouts on bottom of
electric box. Knockouts sizes 1-3/8" (35mm)
or 1-3/4" (45mm) or 2-1/2" (64mm)
Electric handy box factory-installed with cover
Common alarm connection. Field-supplied 24V
Class 2 wiring to common alarm Pigtails 75 + 76,
which are factory-connected to common alarm
relay (R3).
Remote unit shutdown. Replace existing
jumper between Terminals 37 + 38
with normally closed switch having a
minimum 50VA rating. Use field-supplied
24V Class 2 wire.
Three-phase connection.
Electric service connection
terminals when factory-fused
disconnect switch is supplied
Smoke detector alarm connections. Field-supplied 24V.
Class 2 wire to remote alarm circuits. Factory-wired
terminals from optional smoke detector are #91-comm.,
#92-NO, and #93-NC.
Liebert® CW™
Fused Disconnect View
NOTE: Refer to specification sheet for
full load amp. and wire size amp. ratings.
66
DPN001670
Pg. 1, Rev. 3
Electrical Connections
Figure 64 Electrical field connections (Ethernet) for downflow models CW026 - CW084
Low-Voltage Communication Wiring
CAT5E Ethernet connections field-installed.
Avoid routing near high-voltage wiring.
Secure wiring to prevent damage and
use bushing or edge guard to avoid sharp edges.
Monitoring
Panel
3
3
Remove knockouts
to access control board
Crossover
Coupler
Top Entrance
1. When large display is used, both cables (P64 and P66)
are required.
2. On units with the standard, Small Graphic Display,
the customer connection point for unit-to-unit (U2U)
networking is to P64 on the I/O board.
3. On units with the optional Large Graphic Display, a
crossover coupler is provided for unit-to-unit (U2U)
networking. Unplug the red cable from P64 on the I/O
board and connect to one side of the crossover
coupler. The first customer connection point is to
P64 on the I/O board. The second customer
connection point is to the other side of the
crossover coupler. This connects the I/O board and
display to the private U2U network
To display
Electric Box Bottom
Coil Support Frame
P64
Remove
Knockouts
Unit Bottom
Refer to specification sheet for full load
amp and wire size amp ratings.
Bottom Entrance
DPN001670
Pg. 2, Rev. 3
67
Liebert® CW™
Electrical Connections
Figure 65 Electrical field connections for downflow models CW089, CW106 and CW114
Monitoring
Panel
Field-supplied disconnect switch
when factory-installed unit
disconnect switch is not provided.
Select per national and local codes
Three-phase electric service
not by Emerson.
Factory-installed unit
disconnect switch (optional)
Three-phase connection (50Hz). Electric
service connection terminals when
factory disconnect switch is NOT supplied.
Earth ground connection (60 Hz).
Connection terminal for field-supplied
earth grounding wire
Disconnect switch (optional). Factory-installed
Three-phase connection (60Hz). Electric
service connection terminals when
factory disconnect switch is NOT supplied.
Main fuseblock and fuses not present when fused
disconnect installed or on 50Hz units.
Common alarm connection. Field-supplied 24V. Class 1
wiring to common alarm Terminals 75 + 76, which
are factory-connected to common alarm relay (R3).
Smoke detector alarm connections
May be fused
Field-supplied 24V, Class 1 wire to
disconnect with
remote alarm circuits. Factory-wired
internal fuses
terminals from optional smoke detector
are #91-comm., #92-NO, and #93-NC
Customer alarm connections.
Field-supplied 24V, Class 1 wire
Liebert IntelliSlot
for customer alarm Terminals 24,
Housings.
50, 51, 55, 56.
Optional monitoring
Remote unit shutdown. Replace
and
existing jumper between Terminals
communication cards
37 + 38 with normally closed switch
inserted here.
having a minimum 50VA rating. Use
field-supplied 24V Class 1 wire.
Earth ground bar (60Hz). Connection
terminals with factory ground
from each high-voltage component for
field-supplied earth grounding wire.
Three-phase connection. Electric
service connection terminals when
factory disconnect switch is supplied.
Three-phase electric service
not by Emerson.
Three-phase connection. Electric
service connection terminals when
factory-fused disconnect switch
is supplied.
Fused disconnect view
Electric conduit knockouts
on bottom of wire raceway.
Knockout sizes 1-3/8"
(35mm) or 1-3/4" (45mm)
or 2-1/2" (64mm)
NOTE: Refer to specification sheet for full load amp and wire size amp ratings
Liebert® CW™
68
Liebert IntelliSlot
Power Supply Board
Temperature and
Humidity Sensor
DPN001671
Pg. 1, Rev. 6
Electrical Connections
Figure 66 Electrical field connections (Ethernet) for downflow models CW089, CW106 and CW114
Low-Voltage Communication
Wiring CAT5E Ethernet connections
field-installed. Avoid routing near
high-voltage wiring. Secure wiring
to prevent damage and
use bushing or edge guard
to avoid sharp edges.
Monitoring
Panel
Top Entrance
3
3
Remove knockouts
to access control board
Crossover
Coupler
1. When large display is used, both cables (P64 and P66)
are required.
2. On units with the standard, Small Graphic Display,
the customer connection point for unit-to-unit (U2U)
networking is to P64 on the I/O board.
To display
Electric Box Bottom
Remove knockouts
to access control board
3. On units with the optional Large Graphic Display, a
crossover coupler is provided for unit-to-unit (U2U)
networking. Unplug the red cable from P64 on the I/O
board and connect to one side of the crossover
coupler. The first customer connection point is to
P64 on the I/O board. The second customer
connection point is to the other side of the
crossover coupler. This connects the I/O board and
display to the private U2U network
Coil Support Frame
P64
Remove
Knockout
Unit Bottom
Bottom Entrance
Refer to specification sheet for full load
amp and wire size amp ratings.
DPN001671
Pg. 2, Rev. 6
69
Liebert® CW™
Electrical Connections
Figure 67 Electrical field connections (high voltage) for upflow models CW026 - CW084
Field-supplied disconnect switch when factory-installed
unit disconnect switch is not provided
Factory-installed unit disconnect switch (optional).
Monitoring panel
Three-phase connection (50Hz).
Electrical service connection
terminals when factory disconnect
switch is NOT supplied.
Earth ground connection (60Hz).
Connection terminal for field-supplied
earth grounding wire.
Three-phase electric service
not by Emerson
Main fuseblock and fuses not present
when fused disconnect installed or
on 50Hz units.
2 3
Earth ground bar (on 50Hz only).
Connection terminals with factory ground
from each high voltage component for
field-supplied earth grounding wire.
Three-phase connection. Electric
service connection terminals when
factory disconnect switch is supplied
Three-phase connection (60Hz).
Electric service connection terminals
when factory disconnect switch
is NOT supplied.
Factory-installed disconnect
switch (optional ). May be fused
disconnect with internal fuses.
Three-phase electric service not
by Emerson
Electric conduit knockouts on bottom of
electric box. Knockouts sizes 1-3/8"
(35mm) or 1-3/4" (45mm) or 2-1/2"(64mm).
Three-phase connection.
Electric service connection
terminals when factory-fused
disconnect switch is supplied.
NOTE: Refer to specification sheet for full load amp
and wire size amp ratings
Fused disconnect view
Liebert® CW™
70
DPN001672
Rev. 1
Electrical Connections
Figure 68 Electrical field connections (low voltage) for upflow models CW026 - CW084
Underside
of Unit Top
Liebert Intellislot Housings.
Optional Monitoring and
Communication cards inserted here
Back of Unit
Remote unit shutdown. Replace existing
jumper between Terminals 37 + 38
with normally closed switch
having a minimum 50VA rating. Use
field-supplied 24V Class 2 wire
37
38
24
50
Factory
Wiring
91
92
93
51
55
56
75
76
94
95
96
97
Smoke detector alarm connections
Field -supplied 24V. Class 2 wire to
remote alarm circuits. Factory-wired
terminals from optional smoke detector
are #91-comm., #92-NO, and #93-NC
Special alarm connections. Field-supplied
24V, Class 2 wire for special alarms.
Back of
Electric Box
NOTE: Refer to specification sheet for full load
amp. and wire size amp. ratings
DPN001673
Pg. 1, Rev. 3
71
Common Alarm Connections.
Field-supplied 24V. Class 2
wiring to common alarm
Terminals 75 + 76, which are
factory connected to common
alarm relay (R3). Optional
extra common alarm Terminals
94+95 and 96+97 are also
connected to R3 relay
Liebert® CW™
Electrical Connections
Figure 69 Electrical field connections (Ethernet) for upflow models CW026 - CW084
Low-Voltage Communication
Wiring CAT5E Ethernet connections
field-installed. Avoid routing near
high-voltage wiring. Secure wiring
to prevent damage and
use bushing or edge guard
to avoid sharp edges.
Monitoring
Panel
3
Top Entrance
3
3
Remove knockouts
to access control board
Crossover Coupler
1. When large display is used, both cables (P64 and P66)
are required.
2. On units with the standard, Small Graphic Display,
the customer connection point for unit-to-unit (U2U)
networking is to P64 on the I/O board.
3. On units with the optional Large Graphic Display, a
crossover coupler is provided for unit-to-unit (U2U)
networking. Unplug the red cable from P64 on the I/O
board and connect to one side of the crossover
coupler. The first customer connection point is to
P64 on the I/O board. The second customer
connection point is to the other side of the
crossover coupler. This connects the I/O board and
display to the private U2U network
To display
Electric Box Bottom
Coil Support Frame
P64
Remove
Knockouts
Unit Bottom
Refer to specification sheet for full load
amp and wire size amp ratings.
Liebert® CW™
72
Bottom Entrance
DPN001673
Pg. 2, Rev. 3
Electrical Connections
Figure 70 Electrical field connections (Ethernet) for upflow models CW106 and CW114
Low-Voltage Communication
Wiring CAT5E Ethernet connections
field-installed. Avoid routing near
high-voltage wiring. Secure wiring
to prevent damage and
use bushing or edge guard
to avoid sharp edges.
Monitoring
Panel
3
Top Entrance
3
3
Remove knockouts
to access control board
Crossover Coupler
1. When large display is used, both cables (P64 and P66)
are required.
2. On units with the standard, Small Graphic Display,
the customer connection point for unit-to-unit (U2U)
networking is to P64 on the I/O board.
3. On units with the optional Large Graphic Display, a
crossover coupler is provided for unit-to-unit (U2U)
networking. Unplug the red cable from P64 on the I/O
board and connect to one side of the crossover
coupler. The first customer connection point is to
P64 on the I/O board. The second customer
connection point is to the other side of the
crossover coupler. This connects the I/O board and
display to the private U2U network
To display
Electric Box Bottom
Coil Support Frame
P64
Remove
Knockouts
Unit Bottom
Refer to specification sheet for full load
amp and wire size amp ratings.
73
Bottom Entrance
DPN001673
Pg. 2, Rev. 3
Liebert® CW™
Electrical Connections
Figure 71 Electrical field connections (low voltage) for upflow models CW106 and CW114
Monitoring panel
Disconnect
Switch
Knockout for low voltage
wiring connections in
top frame member.
Knockout size 7/8" (22mm)
Remote unit shutdown. Replace
existing jumper between Terminals
37 + 38 with normally closed switch
having a minimum 50VA rating. Use
field-supplied 24V Class 1 wire.
Special alarm connections.
Field -or special alarms
Common alarm connection. Fieldsupplied 24V. Class 1 wiring to
common alarm pigtails 75 + 76,
which are factory connected to
common alarm relay (R3).
Smoke detector alarm connections
Field-supplied 24V. Class 1 wire to remote
alarm circuits. Factory-wired
termkinals from optiona smoke detector
are #91-comm., #92-NO and #93-NC
Intellislot Housings.
Optional Monitoring and
Communication cards inserted here.
DPN001675
Rev. 3
Liebert® CW™
74
Electrical Connections
Figure 72 Electrical field connections (low voltage Ethernet) upflow models CW106 and CW114
Monitoring
Panel
Disconnect
Switch
1. When large display is used, both cables (P64 and P66)
are required.
2. On units with the standard, Small Graphic Display,
the customer connection point for unit-to-unit (U2U)
Low-Voltage Communication
networking is to P64 on the I/O Board.
Wiring CAT5E Ethernet connections
3. On units with the optional Large Graphic Display, a
field-installed. Avoid routing near
crossover coupler is provided for unit-to-unit (U2U)
high-voltage wiring. Secure wiring
networking. Unplug the red cable from P64 on the I/O
to prevent damage and
board and connect to one side of the crossover
use bushing or edge guard
coupler. The first customer connection point is to
to avoid sharp edges.
P64 on the I/O board. The second customer
connection point is to the other side of the
crossover coupler. This connects the I/O board and
display to the private U2U network
3
Top Entrance
3
Crossover Coupler
Remove knockouts
to access
control board
To display
Electric Box Bottom
P64
Remove knockouts
DPN001675
Pg. 2, Rev. 3
Unit Bottom
75
Bottom Entrance
Liebert® CW™
Electrical Connections
Figure 73 Electrical field connections for downflow models CW146 and CW181 with EC fans
Fan Transformer Fuses
(B) Voltage Only
Ground Lug
Cover Plate /
Reversing Starter
Location
Power
4
Block
Humidifier Fuses
Condensate
Reheat
Pump Fuses
Fuses
Control
Fuses
T6 Transformer
Filter Clog
Switch
Main
Fan
Fuses
EM1 Relay
High
Temp
Stat
10
Large Liebert iCOM
A I/O Board
B
C
Terminals for
D
Field Low Voltage
Wiring Connections
Power Block
T1 Transformer
Humidifier
Contactor
8
Liebert IntelliSlot
Power Supply
Liebert
IntelliSlot
Housings
Disconnect
R3 Relay
Reheat
Contactors
3
1
Field High Voltage
Entrance
Main
Fuses
Ground
Current
Detector 4 50Hz
Backup
Reheat
Contactor
Main Fan
Contactor
Electric Panel Layout
CW 60Hz
Note: Typical orientation of components shown.
Component location varies by option and unit.
15
12
11
106 107 110 111 91 92 93 80 81 82 83
6
19
A
17
18
7
Liebert iCOM
Fuse Board
13
16
Refer to text on page 76
for description of
numbered items.
B
5
88 89 37C 38C 37B38B 37 38
C
2
Smoke Detector
Power Supply
58 59 84 85 94 95 96 97 75 76
14
24 50 51 55 56 11 12
CPAR
Relay Remote
Humidifier
Relay
Liebert Liqui-tect
Shutdown
Relay
D
DPN001699
Pg. 3, Rev. 4
Standard Electrical Connections for Downflow Models CW146 and CW181
Refer to Figure 73. Source: DPN001699, Rev. 4.
1. Primary high voltage entrance—2-1/2" (64mm); 1-3/4" (44mm); 1-3/8" (35mm) diameter
concentric knockouts in bottom of box.
2. Primary low voltage entrance—Quantity (3) 1-1/8" (28mm) diameter knockouts in bottom of
box
3. Three-phase electrical service—Terminals are on main fuse block (disregard if unit has
optional disconnect switch). Three-phase service not by Emerson.
4. Earth ground—Terminal for field-supplied earth grounding wire.
5. Remote unit shutdown—Replace existing jumper between Terminals 37 and 38 with
field-supplied normally closed switch having a minimum 75VA, 24VAC rating. Use field-supplied
Class 1 wiring.
6. Customer alarm inputs—Terminals for field-supplied, normally open contacts, having a
minimum 75VA, 24VAC rating, between Terminals 24 and 50, 51, 55, 56. Use field-supplied Class
1 wiring. Terminal availability varies by unit options.
7. Common alarm—On any alarm, normally open dry contact is closed across Terminals 75 and 76
for remote indication. 1A, 24VAC maximum load. Use Class 1 field-supplied wiring.
Liebert® CW™
76
Electrical Connections
Optional Electrical Connections for Downflow Models CW146 and CW181
Refer to Figure 73. Source: DPN001699, Rev. 4.
8. Unit factory installed disconnect switch, Fuse Block and Main Fuses—Two types of
disconnect switches are available – “Non-Locking” and “Locking”. The “Non-Locking Type”
consists of a non-automatic molded case switch operational from the outside of the unit.
Access to the high voltage electric panel compartment can be obtained with the switch in either
the On or Off position. The “Locking Type” is identical, except access to the high voltage electric
panel compartment can be obtained only with the switch in the Off position.
The molded case switch disconnect models contain separate main fuses. Units with fused
disconnect have main fuses within the disconnect.
9. Secondary disconnect switch and earth ground—Fuses are included in the 65KAIC SCCR
fused disconnect switch models.
10. Three-phase electrical service—Terminals are on top of disconnect switch. Three-phase
service not by Emerson.
11. Smoke sensor alarm—Factory-wired dry contacts from smoke sensor are 91-common, 92-NO,
and 93-NC. Supervised contacts, 80 and 81, open on sensor trouble indication. This smoke sensor
is not intended to function as, or replace, any room smoke detection system that may be required
by local or national codes. 1A, 24VAC maximum load. Use field-supplied Class 1 wiring.
12. Reheat and humidifier lockout—Remote 24VAC required at Terminals 82 and 83 for lockout
of reheat and humidifier.
13. Condensate alarm (with condensate pump option)—On pump high water indication,
normally open dry contact is closed across Terminals 88 and 89 for remote indication. 1A, 24VAC
maximum load. Use field-supplied Class 1wiring.
14. Remote humidifier—On any call for humidification, normally open dry contact is closed across
terminals 11 & 12 to signal field supplied remote humidifier. 1A, 24VAC maximum load. Use
Class 1 field-supplied wiring.
15. Reversing Starter Power Supply Notification—Normally open contact Terminals 106 and
107 will close when Power Supply 1 is engaged; 110 and 111 will close when Power Supply 2 is
engaged.
Optional Low Voltage Terminal Package Connections
Refer to Figure 73. Source: DPN001699, Rev. 4.
16. Remote unit shutdown—Two additional contact pairs available for unit shutdown (labeled as
37B and 38B, 37C and 38C). Replace jumpers with field-supplied, normally closed switch having a
minimum 75VA, 24VAC rating. Use field-supplied Class 1 wiring.
17. Common alarm—On any alarm, two additional normally open dry contacts are closed across
Terminals 94 and 95 and 96 and 97 for remote indication. 1A, 24VAC maximum load. Use Class 1,
field-supplied wiring.
18. Main fan auxiliary switch—On closure of main fan contactor, normally open dry contact is
closed across Terminals 84 and 85 for remote indication. 1A, 24VAC maximum load. Use
field-supplied Class 1 wiring.
19. Liebert Liqui-tect® shutdown and dry contact—On Liebert Liqui-tect activation, normally
open dry contact is closed across terminals 58 & 59 for remote indication (Liqui-tect sensor
ordered separately). 1A, 24VAC maximum load. Use field-supplied Class 1 wiring.
EC motor and variable frequency drives create current harmonics that will distort the voltage
waveform of their supply and might affect other equipment on the same power source. The degree of
distortion is dependent on the “stiffness” of the supply power and the total current distortion caused
by all non-linear loads on the system.
The IEEE-519-1992 is the IEEE Recommended Practices and Requirements Guideline for Harmonic
Control in Electrical Power Systems. It defines the maximum voltage distortion limits allowed to be
reflected back onto the utility distribution system. It is a guideline meant to minimize the effects of
electrical pollution created by one utility customer from affecting a different customer. The guideline
requires total voltage harmonic distortion (THD) to not exceed 5% and that the individual current
distortions and total current distortion (TDD) must conform to Table 6. It is NOT a guideline for
77
Liebert® CW™
Electrical Connections
individual connected loads, but a guideline for total building or plant. Many apply the voltage
distortion criteria to all substations (maximum 5% THD) and apply the current distortion criteria
exclusively to the utility metering point (PCC).
Table 6
Maximum harmonic current distortion, IEEE-519-1992
Individual Harmonic Limits
I SC / IL
< 11
< 20
4.0
2.0
1.5
5.0
20 < 50
7.0
3.5
2.5
8.0
50 < 100
10.0
4.5
4.0
12.0
100 < 1000
12.0
5.5
5.0
15.0
7.0
6.0
20.0
> 1000
11 h 17
15.0
17 h 23
TDD
ISC = Maximum Short circuit current @ PCC.
IL = Total load current @ PCC.
TDD = Total Current Distortion
Typically, if the variable speed fan load is less than 10% of the current capacity at the point of
common coupling (PCC), your installation will meet IEEE-519 guidelines. In this case there should be
no interference issues with other electrical equipment. Typically, the worst-case PCC is the
emergency backup generator plant but could be the transformer that powers the cooling load. If the
PCC is a UPS, consult your UPS supplier for recommendations. For customers who have variable
speed loads that exceed this rule of thumb, it may be necessary to minimize the harmonic impact
these variable speed loads have on the system voltage. In these instances, an undesirable effect is a
difficulty in switching from generator supply to utility supply. The purpose of the Liebert CW THD
mitigating transformer is to cancel current harmonics generated by the EC fan. This device is a
passive device, not a harmonic filter or trap, thus it will not cause unintended harmonic resonance
problems. This device will not improve harmonics caused by other systems on the power network.
The Liebert CW THD mitigation device is an optional feature that can be ordered with the Liebert
Thermal Management unit.
Table 7 shows the Total Current Distortion levels as measured on a single CW114 unit and is typical
of what can be expected in the field on CW106, CW114 and CW146 units.
Table 7
Typical TDD for CW106, CW114 and CW146 at 460V
Event Current Harmonic List — 100% Fan Speed
Unfiltered Test Results – 3 Blowers
Filtered Test Results - Transformer + 3 Blowers
Order
(A)
(%)
Order
(A)
(%)
1
13.89
100.0%
1
13.00
100.0%
5
3.29
23.7%
5
0.44
3.4%
7
1.94
14.0%
7
0.33
2.5%
11
1.29
9.3%
11
0.13
1.0%
13
0.92
6.6%
13
0.11
0.9%
17
0.79
5.7%
17
0.66
Broad Spectrum TDD
31.7%
Liebert® CW™
Broad Spectrum TDD
78
5.1%
9.1%
Electrical Connections
Table 7
Typical TDD for CW106, CW114 and CW146 at 460V
Event Harmonic List — 60% Fan Speed
Unfiltered Test Results – 3 Blowers
Order
Filtered Test Results - Transformer + 3 Blowers
(A)
(%)
Order
(A)
(%)
1
4.77
100.0%
1
4.37
100.0%
5
1.96
41.1%
5
0.38
8.6%
7
1.15
24.2%
7
0.31
7.0%
11
0.34
7.1%
11
0.05
1.2%
13
0.35
7.3%
13
0.05
1.2%
17
0.23
4.9%
17
0.23
5.2%
Broad Spectrum TDD
49.9%
Broad Spectrum TDD
14.1%
Table 8 shows the Total Current Distortion level as measured on a single CW181 unit and is typical
of what can be expected in the field on CW181.
Table 8
Typical TDD for CW181 at 460V
Event Current Harmonic List — 100% Fan Speed
Unfiltered Test Results – 3 Blowers
Filtered Test Results - Transformer + 3 Blowers
Order
(A)
(%)
Order
(A)
(%)
1
13.89
100.0%
1
13.00
100.0%
5
3.29
23.7%
5
0.44
3.4%
7
1.94
14.0%
7
0.33
2.5%
11
1.29
9.3%
11
0.13
1.0%
13
0.92
6.6%
13
0.11
0.9%
17
0.79
5.7%
17
0.66
5.1%
31.7%
Broad Spectrum TDD
Broad Spectrum TDD
9.1%
Event Harmonic List — 60% Fan Speed
Unfiltered Test Results – 3 Blowers
Filtered Test Results - Transformer + 3 Blowers
Order
(A)
(%)
Order
(A)
(%)
1
4.77
100.0%
1
4.37
100.0%
5
1.96
41.1%
5
0.38
8.6%
7
1.15
24.2%
7
0.31
7.0%
11
0.34
7.1%
11
0.05
1.2%
13
0.35
7.3%
13
0.05
1.2%
17
0.23
4.9%
17
0.23
49.9%
Broad Spectrum TDD
Broad Spectrum TDD
79
5.2%
14.1%
Liebert® CW™
Electrical Connections
Optional Low-Voltage Terminal Package Connections for Downflow Models CW146 and
CW181
Refer to Figure 73.
20. Remote unit shutdown—Two additional contact pairs available for unit shutdown (labeled as
37B & 38B, 37C & 38C). Replace jumpers with field-supplied, normally closed switch that has a
minimum 75VA, 24VAC rating. Use Class 1 field-supplied wiring.
21. Common alarm—On any alarm, two additional normally open dry contacts are closed across
Terminals 94 and 95 and 96 and 97 for remote indication. 1A, 24VAC maximum load. Use Class 1
field-supplied wiring.
22. Main fan auxiliary switch—On closure of main fan contactor, normally open dry contact is
closed across Terminals 84 and 85 for remote indication. 1A, 24VAC maximum load. Use Class 1
field-supplied wiring.
23. Liebert Liqui-tect® shutdown and dry contact—On Liebert Liqui-tect activation, normally
open dry contact is closed across Terminals 58 and 59 for remote indication (Liebert Liqui-tect
sensor ordered separately). 1A, 24VAC maximum load. Use Class 1 field-supplied wiring.
NOTE
Refer to specification sheet for total unit full load amps, wire size amps and maximum
overcurrent protective device size.
Liebert® CW™
80
Piping
7.0
PIPING
All fluid connections to the unit, with the exceptions of the condensate drain and live steam, are sweat
copper. Factory-installed piping brackets must not be removed. Field-installed piping must be
installed in accordance with local codes and must be properly assembled, supported, isolated and
insulated. Avoid piping runs through noise-sensitive areas, such as office walls and conference rooms.
All piping below the elevated floor must be located so that it offers the least resistance to air flow.
Careful planning of the piping layout under the raised floor is required to prevent the air flow from
being blocked. When installing piping on the subfloor, it is recommended that the pipes be mounted in
a horizontal plane rather than stacked one above the other. Whenever possible, the pipes should be
run parallel to the air flow.
Refer to specific text and detailed diagrams in this manual for other unit-specific piping
requirements.
7.1
Fluid Connections
NOTICE
Risk of clogged or leaking drain lines. Can cause equipment and building damage.
This unit requires a water drain connection. Drain lines must be inspected regularly and
maintenance must be performed to ensure that drain water runs freely through the drain
system and that lines are clear and free of obstructions and in good condition with no visible
sign of damage or leaks. This unit may also require an external water supply to operate.
Improper installation, application and service practices can result in water leakage from the
unit. Water leakage can result in severe property damage and loss of critical data center
equipment.
Do not locate unit directly above any equipment that could sustain water damage.
Emerson recommends installing leak detection equipment for unit and supply lines.
7.1.1
Condensate Piping—Field-Installed
! CAUTION
Risk of boiling water. Can cause injury.
The unit requires a drain line that may contain boiling water. Only properly trained and
qualified personnel wearing appropriate safety equipment should service the drain line or
work on parts near or connected to the drain line.
•
•
•
•
•
Do not reduce drain lines
Do not expose drain line to freezing temperatures
Drain line may contain boiling water. Use copper or other suitable material
Drain line must comply with local building codes
Emerson recommends installing under-floor leak detection equipment
Gravity Drain
• 3/4" NPT drain connection is provided on units without optional factory-installed condensate
pump
• Pitch drain line toward drain a minimum of 1/8" (3mm) per 1 foot (305mm) of length
• Drain is trapped internally. Do not trap external to equipment
• Drain line must be sized for 2 gpm (7.6 l/m) flow
• Drain line must comply with all applicable codes
NOTICE
Risk of improper installation. Can cause unit and/or building damage.
The drain line must not be trapped outside the unit or water may back up in the drain pan
and leak out of the unit on to the building floor(s) below
81
Liebert® CW™
Piping
Figure 74 Gravity drain for downflow and upflow units
DOWNFLOW CW UNIT
UPFLOW CW UNIT
INTERNAL
DRAIN
UNIT
EXTERNAL
DRAIN
INTERNAL
DRAIN
UNIT
EXTERNAL
DRAIN
CONTINUOUS DOWNWARD SLOPE
CORRECT
CORRECT
UNIT
CONTINUOUS DOWNWARD SLOPE
INTERNAL
DRAIN
EXTERNAL
DRAIN
INTERNAL
DRAIN
UNIT
DO NOT EXTERNALLY
TRAP THE UNIT
EXTERNAL
DRAIN
INCORRECT
DO NOT EXTERNALLY
TRAP THE UNIT
INCORRECT
INTERNAL
DRAIN
UNIT
EXTERNAL
DRAIN
INTERNAL
DRAIN
UNIT
EXTERNAL
DRAIN
THESE ARE EXTERNAL TRAPS ALSO, ALTHOUGH
UNINTENTIONAL. LINES MUST BE RIGID ENOUGH
NOT TO BOW OVER TOP OF OTHER OBJECTS.
THESE ARE EXTERNAL TRAPS ALSO, ALTHOUGH
UNINTENTIONAL. LINES MUST BE RIGID ENOUGH
NOT TO BOW OVER TOP OF OTHER OBJECTS.
INCORRECT
Liebert® CW™
INCORRECT
82
DPN001556
Rev. 0
Piping
Condensate Pump
• 1/2" copper sweat connection is provided on units with optional factory-installed condensate
pump
• Condensate Pump (60Hz): Condensate pump is rated for approximately 400 gph at 10 feet total
head
• Condensate Pump (50Hz): Condensate pump is rated for approximately 315 gph at 10 feet total
head
• Size piping based on available condensate head
• Condensate pump discharge (drain) line must comply with all applicable codes
NOTE
For units with a field-installed condensate pump, the unit is shipped from the factory with the
condensate pump option, unmounted in the unit, which must be installed in the field. The unit
has an internally mounted trap. The drain line from the unit to the condensate pump does not
require a trap. The discharge (drain) line from the pump must comply with all applicable
codes.
7.1.2
Humidifier Supply Water—Optional Infrared
• 1/4" supply line; maximum water pressure is 150 psi (1034kPa)
• Size humidifier supply line for 1 gpm (3.8 l/m), with a minimum water pressure of 20 psi (138kPa)
• Do not supply de-ionized water to the humidifier
7.1.3
Humidifier Supply Water—Optional Steam Generating Humidifier
• Water conductivity of 200-500 micro-siemens required for optimum operation.
• 1/4" supply line
Leak Checking of Unit and Field Piping
Liebert unit fluid systems are factory-checked for leaks and may be shipped with a nitrogen holding
charge. Liebert unit fluid circuits should be checked for leaks at installation as described below.
NOTE
During leak checking of field-installed piping, Emerson recommends that the unit be isolated
using field-installed shutoff valves. When Liebert CW units are included in a leak test, use of
fluid for pressure testing is recommended. When pressurized gas is used for leak testing a
Liebert CW unit, the maximum recommended pressure is 30 psig (2 bars) and tightness of the
unit should be verified by pressure decay over time, (<2 psig/hour [0.3 bars/hour]) or sensing a
tracer gas with suitable instrumentation. Dry seals in fluid valves and pumps may not hold a
high gas pressure.
83
Liebert® CW™
Piping
7.2
Chilled Water Piping
7.2.1
Requirements of Systems Using Water or Glycol
These guidelines apply to the field leak checking and fluid requirements for field piping systems,
including Liebert chilled water, hot water, condenser (water or glycol), GLYCOOL and drycooler
circuits.
General Guidelines
• Equipment damage and personal injury can result from improper piping installation, leak checking, fluid chemistry and fluid maintenance.
• Follow local piping codes, safety codes.
• Properly trained and qualified personnel must install and inspect system piping.
• Contact a local water consultant regarding water quality, corrosion protection and freeze protection requirements.
• Install manual shutoff valves at the supply and return line to each indoor unit and drycooler to
permit routine service and emergency isolation of the unit.
NOTICE
Risk of frozen fluids. Can cause equipment damage and building damage.
Freezing system fluids can rupture piping. Complete system drain-down cannot be ensured.
When the field piping or unit may be exposed to freezing temperatures, charge the system
with the proper percentage of glycol and water for the coldest design ambient.
Automotive antifreeze is unacceptable and must NOT be used in any glycol fluid system.
NOTICE
Risk of corrosion. Can cause equipment damage.
Read and follow individual unit installation instructions for precautions regarding fluid
system design, material selection and use of field-provided devices. Liebert systems contain
iron and copper alloys that require appropriate corrosion protection. Contact a local water
consultant regarding water quality, corrosion and freeze protection requirements.
Water chemistry varies greatly by location, as do the required additives, called inhibitors,
that reduce the corrosive effect of the fluids on the piping systems and components. The
chemistry of the water used must be considered, because water from some sources may
contain corrosive elements that reduce the effectiveness of the inhibited formulation.
Preferably, surface waters that are classified as soft and are low in chloride and sulfate ion
content should be employed. Proper inhibitor maintenance must be performed in order to
prevent corrosion of the system. Consult glycol manufacturer for testing and maintenance of
inhibitors.
Commercial ethylene glycol (Union Carbide Ucartherm, Dow Chemical Dowtherm SR-1 and
Texaco E.G. Heat Transfer Fluid 100), when pure, is generally less corrosive to the common
metals of construction than water itself. It will, however, assume the corrosivity of the water
from which it is prepared and may become increasingly corrosive with use if not properly
inhibited.
Liebert® CW™
84
Piping
NOTICE
Risk of corrosion. Can cause equipment damage.
Read and follow individual unit installation instructions for precautions regarding fluid
system design, material selection and use of field-provided devices. Liebert systems contain
iron and copper alloys that require appropriate corrosion protection.
Contact a water consultant about water quality, corrosion and freeze protection requirements.
Water chemistry varies greatly by location, as do the required additives, called inhibitors, that
reduce the corrosive effect of the fluids on the piping systems and components. The chemistry
of the water used must be considered, because water from some sources may contain corrosive
elements that reduce the effectiveness of the inhibited formulation. Preferably, surface waters
that are classified as soft and are low in chloride and sulfate ion content should be employed.
Proper inhibitor maintenance must be performed to prevent corrosion of system components.
Consult glycol manufacturer for testing and maintenance of inhibitors.
Commercial ethylene glycol (Union Carbide Ucartherm, Dow Chemical Dowtherm SR-1 and
Texaco E.G. Heat Transfer Fluid 100), when pure, is generally less corrosive to the common
metals of construction than water itself. It will, however, assume the corrosivity of the water from
which it is prepared and may become increasingly corrosive with use if not properly inhibited.
Leak Checking of Unit and Field Piping
Liebert unit fluid systems are factory-checked for leaks and may be shipped with a nitrogen holding
charge. Liebert unit fluid circuits should be checked for leaks at installation as described below.
NOTE
During leak checking of field-installed piping, Emerson recommends that the unit be isolated
using field-installed shutoff valves. When Liebert CW units are included in a leak test, use of
fluid for pressure testing is recommended. When pressurized gas is used for leak testing a
Liebert CW unit, the maximum recommended pressure is 30 psig (2 bars) and tightness of the
unit should be verified by pressure decay over time, (<2 psig/hour [0.3 bars/hour]) or sensing a
tracer gas with suitable instrumentation. Dry seals in fluid valves and pumps may not hold a
high gas pressure.
Manual shutoff valves should be installed at the supply and return lines to each unit. This provides
for routine service and emergency isolation of the unit.
The lowest water temperature to be supplied by the chiller will determine whether insulation is
needed to prevent condensation on the supply and return lines. To prevent water damage to flooring
and subflooring, install a water detection system, such as a Liqui-tect or floor drains with wet traps.
85
Liebert® CW™
Piping Schematics
8.0
PIPING SCHEMATICS
Figure 75 Downflow general arrangement, CW026-CW114
Airflow
Bleed
Valve
Valve
Actuator
Chilled
Water
Return
AB
Chilled
Water
Supply
A
B
Ball
Valve
(Optional)
Shutoff *
Valves
3-Way
Chilled
Water
Valve
Chilled Water Coil
Airflow
Flow Switch
(Optional)
Hose*
Bibs
3-WAY VALVE
Bleed
Valve
Chilled
Water
Return
Valve
Actuator
Chilled Water Coil
Chilled
Water
Supply
2-Way Chilled
Water Valve
Shutoff *
Valves
2-WAY VALVE
Ball Valve
(Optional)
FACTORY PIPING
FIELD PIPING
Hose*
Bibs
*Components are not supplied by Emerson but
are recommended for proper circuit operation
and maintenance.
Liebert® CW™
86
DPN001657
Rev. 2
Piping Schematics
Figure 76 Downflow general arrangement, CW181-CW146
Airflow
Ball Valve
(Optional)
Valve
Actuator
Chilled Water
Return
Chilled Water Coil
Chilled
Water
Supply
Shutoff *
Valves
2-Way Chilled
Water Valve
2-WAY VALVE
Airflow
Hose*
Bibs
Chilled Water
Return
A
Valve
Actuator
Chilled
Water
Supply
AB
B
Chilled Water Coil
Shutoff *
Valves
A
Ball
Valve
(Optional)
Hose*
Bibs
Flow
Switch
(Optional)
AB
B
3-Way
Chilled
Water
Valve
3-WAY VALVE
FACTORY PIPING
FIELD PIPING
*Components are not supplied by Emerson but
DPN001657
are recommended for proper circuit operation
and maintenance.
Pg. 2, Rev. 2
87
Liebert® CW™
Piping Schematics
Figure 77 Primary connection locations, downflow models CW026 - CW041 with EC fans
A
All Dimensions From
Right Rear Corner of Unit
with Panels Assembled
A
Front View
X
Section A-A
Note: Drawing Not To Scale.
Tolerance on all piping locating
dimensions ± 1/2" (13mm).
0
Y
31" (787mm)
Air Discharge
Area
28-1/16"
(714mm)
Air Discharge Area
35"
(889mm)
CD
LV
CWP
B
HV
HUM
50" (1270mm)
Front of Unit
Point
CD
HUM
CWP
Description
Condensate Drain *
W/Optional Condensate Pump **
X, in (mm)
Y, in (mm)
35-1/16 (891)
29-5/16 (745)
DPN002036
Rev. 1
Connection Size / Opening, in (mm)
3/4 (19) FPT
1/2 (13) Cu Sweat
Humidifier Supply Line
34-9/16 (878)
31 3/8 (797)
1/4 (6) Cu Sweat
Chilled Water Piping Slot (Center)
43-7/16 (1104)
31-5/8 (803)
9 x 2-1/2 (229 x 64)
—
—
CW026: 1-1/8 (29)
Supply and Return Piping Diameter
CW038: 1-3/8 (32)
CW041: 1-5/8 (41)
HV
High Volt Electrical Connection
37-7/16 (951)
31-5/8 (803)
2-1/2 (64)
LV
Low Volt Electrical Connection
35-7/16 (900)
31-5/8 (803)
7/8 (22)
B
Blower Outlet Opening
4 (101)
33 (838)
28-1/16 x 31 (714 x 787)
*
Field pitch Condensate Drain line a minimum of 1/8" (3.2 mm) per foot (305 mm). All units contain a factory-installed condensate trap. Do
not trap external to the unit. Drain line may contain boiling water. Select appropriate drain system materials. The drain line must comply
with all local codes.
** Optional Condensate Pump to be field-installed under unit.
Source: DPN002036, Rev. 1
Liebert® CW™
88
Piping Schematics
Figure 78 Primary connection locations, downflow models CW051 and CW060 with EC fans
Note: Drawing Not To Scale.
Tolerance on all piping locating
dimensions ± 1/2" (13mm).
All Dimensions From
A
A Right Rear Corner Of Unit
Including Panels
Front View
X
Section A-A
0
Y
31" (787mm)
Typical Air
Discharge Area
CD
CWP
24-1/2" (623mm)
Typical Air
Discharge Area
24-1/4"
(615mm)
Air Discharge
Area
35"
(889mm)
HV
B
LV
HUM
74" (1880mm)
Front of Unit
Point
CD
HUM
CWP
Description
Condensate Drain*
W/Optional Condensate Pump**
DPN002035
Rev. 1
X, in (mm)
Y, in (mm)
60-7/8 (1547)
27-3/4 (705)
Connection Size / Opening, in (mm)
3/4 (19) FPT
1/2 (13) Cu Sweat
Humidifier Supply Line
59-1/8 (1502)
25-5/8 (727)
1/4 (6) Cu Sweat
Chilled Water Piping Slot (Center)
66-9/16 (1691)
31-1/4 (794)
11 x 3 (279 x 76)
—
—
Supply & Return Piping Diameter
CW051: 1-5/8 (41)
CW060: 2-1/8 (54)
HV
High Volt Electrical Connection
59 3/8 (1509)
30-3/4 (781)
3 (76)
LV
Low Volt Electrical Connection
60-7/8 (1547)
29-1/4 (743)
7/8 (22)
B
Blower Outlet Opening
4 (101)
33 (838)
51 x 31 (1295) x 787)
*
Field pitch Condensate Drain line a minimum of 1/8" (3.2 mm) per foot (305 mm). All units contain a factory installed condensate trap. Do
not trap external to the unit. Drain line may contain boiling water. Select appropriate drain system materials. The drain line must comply
with all local codes.
** Optional Condensate Pump to be field installed under unit.
Source: DPN002035, Rev. 1
89
Liebert® CW™
Piping Schematics
Figure 79 Primary connection locations, downflow models CW076 - CW084 with EC fans
Note: Drawing not to scale.
A
A
Front View
Section A-A
Tolerance on all piping locating
dimensions ± 1/2" (13mm).
All Dimensions From
Rear Corner Of Unit
Including Panels
X
0
Y
31" (787mm)
Typical Air Discharge Area
28" (711mm)
Typical Air Discharge Area
35"
(889mm)
HUM
HV
CWP
LV
CD
B
99" (2514mm)
Front Of Unit
DPN002034
Rev. 1
Point
CD
HUM
CWP
Description
Condensate Drain *
X, in (mm)
Y, in (mm)
Connection Size / Opening, in (mm)
76-3/8 (1940)
30-7/8 (784)
3/4 (19) FPT
W/Optional Condensate Pump
76-3/8 (1940)
30-7/8 (784)
1/2 (13) Cu Sweat
Humidifier Supply Line
73-7/16 (1865)
31-7/16 (799)
1/4 (6) Cu Sweat
Chilled Water Piping Slot (Center)
91-3/8 (2321)
31-3/8 (797)
101-5/16 x 2-15/16 (277 x 74)
Supply and Return Piping Diameter
—
—
2-1/8 (54)
HV
High Volt Electrical Connection
83-7/8 (2130)
30-7/8 (784)
3 (76)
LV
Low Volt Electrical Connection
81-3/8 (2067)
31-7/16 (799)
7/8 (22)
B
Blower Outlet Opening
9-13/16 (249)
33 (838)
60-13/16 x 31 (1544 x 787)
*
Field pitch Condensate Drain line a minimum of 1/8" (3.2 mm) per foot (305 mm). All units contain a factory-installed condensate trap. Do
not trap external to the unit. Drain line may contain boiling water. Select appropriate drain system materials. The drain line must comply
with all local codes.
Source: DPN002034, Rev. 1
Liebert® CW™
90
Piping Schematics
Figure 80 Primary connection locations, downflow models CW089, CW106 and CW114 with EC fans
NOTE: Drawing not to scale.
Tolerance on all
piping dimensions
is ±1/2" (13mm).
A
All dimensions from
rear corner of unit
including panels
X
A
FRONT VIEW
SECTION A-A
O
Y
CWR 3
CWS 3
28-1/16"
(712mm)
Typical Air
Discharge Area
31"
(787mm)
Typical Air
Discharge Area
CWS 2
LV1
E1
CD
HUM
CWR 2
Point
CD
Description
Condensate Drain *
35"
(889mm)
LV2
E2
B
FRONT OF UNIT
DPN001628
Rev. 5
122" (3099mm)
X, in. (mm)
Y, in. (mm)
Connection Size / Opening
103-1/2 (2629)
28 (711)
1-1/4" FPT
W/ Optional Pump
103-1/2 (2629)
28 (711)
1/2" Cu Sweat
Humidifier Supply Line
107-1/2 (2731)
29 (737)
1/4" Cu Sweat
CWS 2
2-Way Chilled Water Supply
118-1/2 (3010)
31 (787)
CW106: 2-1/8"; CW089, CW114: 2-5/8"
CWS 3
3-Way Chilled Water Supply
115-1/2 (2934)
31 (787)
CW106: 2-1/8"; CW089, CW114: 2-5/8"
CWR 2
2-Way Chilled Water Return
112-1/2 (2858)
31 (787)
CW106: 2-1/8"; CW089, CW114: 2-5/8"
CWR 3
3-Way Chilled Water Return
115-1/2 (2934)
22 (559)
CW106: 2-1/8"; CW089, CW114: 2-5/8"
HUM
E1
Electrical Connection (High Volt)
35 (889)
31 (787)
2"
E2
Electrical Connection (High Volt)
34 (864)
29 (737)
2"
LV1
Electrical Connection (Low Volt)
35-1/2 (902)
26-1/2 (673)
1-3/8"
LV2
Electrical Connection (Low Volt)
33-1/2 (851)
26-1/2 (673)
1-3/8"
4 (102)
33 (838)
94 x 31 (2388mm x 787mm)
B
Blower Outlet
*
Field-pitch condensate drain line a minimum of 1/8" (3.2 mm) per foot (305 mm). All units contain a factory-installed condensate
trap. Do not trap external to the unit. Drain line may contain boiling water. Select appropriate drain system materials. The drain line
must comply with all local codes.
Source: DPN001628, Rev. 5
91
Liebert® CW™
Piping Schematics
Figure 81 Primary connection locations, downflow models CW146 and CW181 with EC fans
NOTE: Drawing not to scale.
Tolerance on all
piping dimensions
is ±1/2" (13mm).
FRONT VIEW
All dimensions from
rear corner of unit
including panels
SECTION A-A
X
A
A
O
Y
41"
(1041mm) TYP
AIR DISCHARGE
AREA
CWR
29-3/8"
(746mm) TYP
AIR DISCHARGE
AREA
47"
(1194mm)
CD
LV1
LV2
LV3
HUM
CWS
B
E1 E2
FRONT OF UNIT
122" (3099mm)
DPN001693
Rev. 2
Point
CD
Description
Condensate Drain *
X
In. (mm)
Y
In. (mm)
Connection Size / Opening
110 (2794)
35 (889)
1-1/4" FPT
W/ Optional Pump
110 (2794)
35 (889)
1/2" Cu Sweat
Humidifier Supply Line
101 (2565)
43 (1092)
1/4" Cu Sweat
2-Way Chilled Water Supply
117 (2972)
37 (940)
3-1/8"
3-Way Chilled Water Supply
117 (2972)
37 (940)
3-1/8"
2-Way Chilled Water Return
117 (2972)
30 (762)
3-1/8"
3-Way Chilled Water Return
117 (2972)
30 (762)
3-1/8"
E1
Electrical Conn. (High Volt)
113 (2870)
43 (1092)
2"
E2
Electrical Conn. (High Volt)
110 (2794)
43 (1092)
2"
HUM
CWS
CWR
LV1
Electrical Conn. (Low Volt)
2-1/2 (64)
36 (914)
7/8"
LV2
Electrical Conn. (Low Volt)
2-1/2 (64)
37-1/2 (953)
7/8"
LV3
Electrical Conn. (Low Volt)
2-1/2 (64)
39 (991)
7/8"
Blower Outlet
4-1/2 (114)
44 (1118)
93" x 41" (2362mmx1041mm)
B
*
Field-pitch condensate drain line a minimum of 1/8" (3.2 mm) per foot (305 mm). All units contain a factory-installed condensate trap. Do
not trap external to the unit. Drain line may contain boiling water. Select appropriate drain system materials. The drain line must comply
with all local codes.
Source: DPN001693, Rev. 2
Liebert® CW™
92
Piping Schematics
Figure 82 Primary connection locations, downflow units, model CW300 and CW400 with EC fans
A
NOTE: Drawing not to scale.
Tolerance on all piping
dimensions is ± 1/2" (13mm).
A
FRONT VIEW
SECTION A-A
CWR2
92"
(2337mm)
CD2
CWS2
C
41"
(1041mm) typ.
Air Discharge
Area
CWR1
CD1
Y
E2
B
X
All dimensions from front corner
of unit including panels
Point
CD 1
CD 2
CWS1
CWS2
CWR1
CWR2
LV1
LV2
LV3
CWS1
E1
O
46"
(1168mm)
29-3/8"
(746mm) typ.
Air Discharge
Area
Description
122" (3099mm)
DPN002434
Rev. 0
Front of Unit
X, In. (mm)
Y, In. (mm)
Connection Size / Opening
Condensate Drain *
12 (305)
12 (305)
1-1/4" FPT
W/ Optional Pump
12 (305)
12 (305)
1/2" Cu Sweat
Condensate Drain *
12 (305)
57 (1449)
1-1/4" FPT
W/ Optional Pump
12 (305)
57 (1449)
1/2" Cu Sweat
2-way Chilled Water Supply
5 (127)
10 (254)
3-1/8"
3-way Chilled Water Supply
5 (127)
10 (254)
3-1/8"
2-way Chilled Water Supply
5 (127)
55 (1397)
3-1/8"
3-way Chilled Water Supply
5 (127)
55 (1397)
3-1/8"
2-way Chilled Water Return
5 (127)
17 (432)
3-1/8"
3-way Chilled Water Return
5 (127)
17 (432)
3-1/8"
2-way Chilled Water Return
5 (127)
62 (1575)
3-1/8"
3-way Chilled Water Return
5 (127)
62 (1575)
3-1/8"
E1
Electrical Conn. (High Volt)
9 (229)
4 (102)
2"
E2
Electrical Conn. (High Volt)
12 (305)
4 (102)
2"
LV1
Electrical Conn. (Low Volt)
119-1/2 (3035)
11 (279)
7/8"
LV2
Electrical Conn. (Low Volt)
119-1/2 (3035)
9-1/2 (241)
7/8"
LV3
Electrical Conn. (Low Volt)
119-1/2 (3035)
8 (203)
7/8"
B
Front Blower Outlet
24-1/2 (622)
3 (76)
93" x 41" (2362mm x 1041mm)
C
Rear Blower Outlet
24-1/2 (622)
48 (1219)
93" x 41" (2362mm x 1041mm)
*
Field pitch Condensate Drain line a minimum of 1/8" (3.2 mm) per foot (305 mm). All units contain a factory-installed condensate trap. Do
not trap external to the unit. Drain line may contain boiling water. Select appropriate drain system materials. The drain line must comply
with all local codes.
Source: DPN002434, Rev. 0
93
Liebert® CW™
Piping Schematics
Figure 83 Piping connections, downflow models CW026 - CW084 with centrifugal fans
Monitoring
Panel
NOTE: Install all piping
per local codes.
Condensate Drain. Field-pitch a min. of
1/8" (3mm) per ft. (305mm). 3/4" NP T for units
without factory installed condensate pump. Do
not install an external trap. 1/2" OD CU for units
with factory-installed condensate pump
1/4" OD CU Humidifier Supply Line (Steam Gen./Infrared)
C - Steam Reheat Supply Line
D - Hot Water Reheat Supply Line
E - Steam Reheat Return Line
(Field-install factory-supplied steam
trap with vacuum breaker)
F - Hot Water Reheat Return Line
1/2" NPT Male Steam Humidifier Supply Line
1/2" NPT Male Steam Humidifier Return Line
OPTIONAL REHEAT SCHEMATICS
Supply
B - Chilled Water Return Line.
- Chilled Water Supply Line on units with High Pressure
2 Way Valve Only
A - Chilled Water Supply Line
- Chilled Water Return Line on units with High Pressure
2-Way Valve Only
Return
Y-Strainer
Actuator
Steam Humidifier
Steam Trap
Return
Supply
Y-Strainer
Hot Water Reheat Coil
Optional Hot Water Reheat (2-Way Valve)
Optional Steam Humidifier
Actuator
Actuator
Supply
Return
Y-Strainer
Return
Steam Trap
Supply
Steam Reheat Coil
Y-Strainer
Hot Water Reheat Coil
Optional Hot Water Reheat (3-Way Valve)
Optional Steam Reheat
DPN001666
Rev. 0
Models
A
(OD Cu)
B
(OD Cu)
C
(NPT Male)
D
(OD Cu)
E
(NPT Male)
F
(OD Cu)
CW026
1-1/8
1-1/8
1/2
5/8
1/2
5/8
CW038
1-3/8
1-3/8
1/2
5/8
1/2
5/8
CW041
1-5/8
1-5/8
1/2
5/8
1/2
5/8
CW051
1-5/8
1-5/8
1/2
7/8
1/2
7/8
CW060
2-1/8
2-1/8
3/4
7/8
3/4
7/8
CW076
2-1/8
2-1/8
3/4
7/8
3/4
7/8
CW084
2-1/8
2-1/8
3/4
7/8
3/4
7/8
Source: DPN001666, Rev. 0
Liebert® CW™
94
Piping Schematics
Figure 84 Piping connections for downflow models CW106 and CW114 with centrifugal fans
Monitoring
Panel
NOTE: Install all piping
per local codes.
3/4" NPT Steam Generating Canister Humidifier
Drain. Field-pitch a minimum of 1/8" (3mm)
per ft. (305mm). Do not install an external trap.
1/4" OD CU Humidifier Water Supply Line
Condensate Drain. Field-pitch a min. of
1/8" (3mm) per ft. (305mm). 1-1/8" NP T for units
without factory-installed condensate pump. Do
not install an external trap. 1/2" OD CU for units
with factory-installed condensate pump
1/2" NPT Male Steam Humidifier Return Line
1/2" NPT Male Steam Humidifier Supply Line
B - Chilled Water Return Line.
3-Way Valve Only
A - Chilled Water Supply Line
- Chilled Water Return Line
on units with High Pressure
2-Way Valve Only
B - Chilled Water Return Line
- Chilled Water Supply Line
on units with High Pressure
2-Way Valve Only
C-D - Steam/Hot Water Reheat Supply Line
E-F - Steam/Hot Water Reheat Return Line
OPTIONAL REHEAT SCHEMATICS
Supply
Return
Actuator
Y-Strainer
Steam Humidifier
Steam Trap
Return
Supply
Y-Strainer
Hot Water Reheat Coil
Optional Hot Water Reheat (2-Way Valve)
Optional Steam Humidifier
Actuator
Actuator
Supply
Return
Y-Strainer
Return
Supply
Y-Strainer
Steam Reheat Coil
Steam Trap
Hot Water Reheat Coil
Optional Steam Reheat
Optional Hot Water Reheat (3-Way Valve)
DPN001667
* This drawing pertains to CW106 & CW 114 with forward curve blowers onl y.
Rev. 0
Piping Connection Sizes, inches
Model
Numbers
A
OD Cu
B
OD Cu
C
NPT Male
D
OD Cu
E
NPT Male
F
OD Cu
CW106
2-1/8
2-1/8
3/4
7/8
3/4
7/8
CW114
2-5/8
2-5/8
3/4
7/8
3/4
7/8
Source: DPN001667, Rev. 0
95
Liebert® CW™
Piping Schematics
Figure 85 Upflow general arrangement
Air Flow
Chilled
Water
Supply
Bleed
Valve
Chilled
Water
Return
Valve
Actuator
Shutoff *
Valves
Chilled Water Coil
A
AB
B
Flow
Switch
(Optional
Hose*
Bibs
3-Way
Chilled
Water
Valve
3-WAY VALVE
Air Flow
Chilled
Water Supply
Chilled
Water
Return
lve
Ball Va
al)
(Option
Valve
Actuator
Bleed
Valve
2-Way
Chilled
Water
Valve
Chilled Water Coil
Shutoff *
Valves
2-WAY VALVE
Ball Valve
(Optional)
Hose*
Bibs
FACTORY PIPING
FIELD PIPING
*Components are not supplied by Liebert
but are recommended for proper
circuit operation and maintenance.
Liebert® CW™
96
DPN001658
Rev. 0
Piping Schematics
Figure 86 Piping connections for upflow models CW026 - CW084
UNIT FIELD PIPING LOCATIONS
Piping stubbed out inside unit end compartment for field
connection through 2 5/8" x 10 3/4" (66 x 273mm)
opening as shown. Piping may also exit through bottom
or top of end compartment by field cutting an opening in
a suitable location (except bottom return air units).
1" (25mm) Rear Panel
1-1/32" (26mm)
2-5/8" (66mm)
10-3/4"
(273mm
7-1/2"
(191mm)
PLENUM FIELD PIPING LOCATIONS
For separate steam or hot water plenum in UPFLOW (UH)
units, piping may exit through bottom, top or sides by field
cutting an opening in a suitable location.
A - Chilled Water Supply Line.
(Line is stubbed down, field
install elbow for side
connection).
B - Chilled Water Return Line.
(Line is stubbed down, field
install elbow for side
connection).
1/4" OD CU Humidifier Water
Supply Line.
Condensate Drain. Field pitch a min. of
1/8" (3mm) per ft. (305mm). 3/4" NP T
for units without factory installed
condensate pump. Do not install an
external trap.
1/2" OD CU for units with factory
installed condensate pump.
Piping outlet location on units
w/rear return option.
Unit Left
End Panel
NOTE: Install all piping
per local codes.
Plenum Left
End Panel
1/2" NPT Female Steam
Humidifier Supply Line
1/2" NPT Female Steam
Humidifier Return Line
C - Steam Reheat Supply Line
F - Hot Water Reheat Return
Line
E - Steam Reheat Return Line
(Field-install factory-supplied
steam trap with vacuum breaker)
D - Hot Water Reheat
Supply Line
OPTIONAL REHEAT SCHEMATICS
Supply
Return
Actuator
Steam Humidifier
Return
Supply
Steam Trap
Hot Water Reheat Coil
Y-Strainer
Optional Hot Water Reheat (2-Way Valve)
Optional Steam Humidifier
Actuator
Actuator
Supply
Return
Y-Strainer
Return
Supply
Steam Reheat Coil
Steam Trap
Hot Water Reheat Coil
Y-Strainer
Optional Hot Water Reheat (3-Way Valve)
Optional Steam Reheat
DPN001668
Rev. 0
Factory-Provided Piping Connection Sizes, inches
Models
A, OD Cu
B, OD Cu
C, NPT Female
D, OD Cu
E, NPT Female
F, OD Cu
CW026
1-1/8
1-1/8
1/2
5/8
1/2
5/8
CW038
1-3/8
1-3/8
1/2
5/8
1/2
5/8
CW041
1-5/8
1-5/8
1/2
5/8
1/2
5/8
CW051
1-5/8
1-5/8
3/4
7/8
3/4
7/8
CW060
2-1/8
2-1/8
3/4
7/8
3/4
7/8
CW076
2-1/8
2-1/8
3/4
7/8
3/4
7/8
CW084
2-1/8
2-1/8
3/4
7/8
3/4
7/8
Source: DPN001668, Rev. 0
97
Liebert® CW™
Piping Schematics
Figure 87 Piping connections for upflow models CW106 and CW114
Piping stubbed out inside unit end
compartment for field-connection
through 13" x 6-1/2" (330 x 165mm)
opening as shown. Piping also may
exit through bottom of end
compartment by field-cutting
an opening.
A - Chilled Water Supply Line.
2-5/8" O.D. Cu on three-way
front return units only.
1/4" OD Cu Humidifier Water
Supply Line.
Condensate Drain
Field-pitch a min. of 1/8" (3mm) per ft. (305mm).
1-1/4" NPT for units without a factory-installed
condensate pump.
1/2" OD Cu for units with factory-installed
condensate pump. Do not install an external trap.
1" (25mm)
Rear Panel
A - Chilled Water Supply Line
2-5/8" O.D. Cu on three-way
front return units only.
B - Chilled Water Return Line
2-5/8" O.D. Cu
7-1/2" (191mm)
3" (76mm)
Note: Install all piping
per local codes.
Unit left
end panel
DPN001669
Rev. 0
13"
(330mm)
Liebert® CW™
98
Checklist for Completed Installation
9.0
CHECKLIST FOR COMPLETED INSTALLATION
9.1
Moving and Placing Equipment
___ 1. Unpack and check received material.
___ 2. Proper clearance for service access has been maintained around the equipment.
___ 3. Equipment is level and mounting fasteners are tight.
___ 4. If the equipment has been disassembled for installation, unit must be reassembled per
instructions.
9.2
Electrical
___ 1. Supply voltage and phase matches equipment nameplate.
___ 2. Wiring connections completed between disconnect switch and unit.
___ 3. Power line circuit breakers or fuses have proper ratings for equipment installed.
___ 4. All internal and external high- and low-voltage wiring connections are tight.
___ 5. Confirm that unit is properly grounded to an earth ground.
___ 6. Control transformer setting matches incoming power.
___ 7. Electrical service conforms to national and local codes.
___ 8. Check blowers for proper rotation.
9.3
Piping
___ 1. Piping completed to coolant.
___ 2. Piping has been checked for leaks.
___ 3. Piping is properly sized, sloped, trapped as shown in the piping schematics
___ 4. Check piping inside and outside of equipment for proper support.
___ 5. Ensure that factory clamps have been reinstalled
___ 6. Drain line connected and pitched per local code.
___ 7. Water supply line connected to humidifier
9.4
Other
___ 1. Ducting complete (if required), maintain access to filters.
___ 2. Filters installed.
___ 3. Check fasteners that secure reheats, humidifier and motors-some may have become loose
during shipment.
___ 4. Verify water detection is properly installed around all units.
___ 5. Control panel DIP switches are set based on user requirements.
___ 6. Blower drive system rotates freely and belts are properly aligned and tensioned
___ 7. All fans are free of debris.
___ 8. Remove rubber band from float in optional infrared humidifier.
___ 9. Installation materials and tools have been removed from equipment (literature, shipping
materials, construction materials, tools, etc.)
___ 10. Locate blank startup sheet, ready for completion by installer or startup technician.
99
Liebert® CW™
Initial Startup Checks and Commissioning Procedure for Warranty Inspection
10.0 INITIAL STARTUP CHECKS AND COMMISSIONING PROCEDURE FOR WARRANTY
INSPECTION
Locate the startup form supplied with the unit documents. Complete the form during startup and
mail it to your local Emerson Network Power sales office after startup is completed. Contact your
Emerson supplier if you have any questions or problems during installation, startup or operation.
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect all local and remote electrical
power supplies before working within the unit.
Potentially lethal voltages exist within this equipment during operation. Observe all cautions
and warnings on the unit and in this manual. Failure to do so could result in serious injury or
death. Only properly trained and qualified service and maintenance personnel should work
with this equipment.
! WARNING
Risk of fire suppression and alarm system activation. Can cause injury or death during
building evacuation and mobilization of emergency fire and rescue services.
Startup operation of optional electric reheat elements may activate facility alarm and fire
suppression system. Prepare and take appropriate steps to manage this possibility. Activating
reheat during initial startup may burn off particulates from electric reheat elements.
Check the steam generating humidifier electrode plugs to ensure that they are pressed firmly
onto the pins. Loose connections will cause the cylinder and plugs to overheat.
Before beginning initial startup checks, make certain that unit was installed according to the
instructions in this manual. All exterior panels must be in place.
10.1
Information for Warranty Inspection—Remove Power From Unit Disconnect
Complete the following items on the warranty inspection form:
Installer name and address
Owner name and address
Site contact name and phone number
Installation date
Indoor unit model number and serial number
Condition of unit when received
Is there a freight damage claim in process? If so, have all relevant parties been notified?
Have manuals been kept with unit?
Is the Liebert Thermal Management unit connected to site monitoring or switchover controls?
Provide model and serial of connected controls for switchover controls.
10.2
Startup Checks With Panels Removed and Main Disconnect Off
___ 1. Check all internal piping clamps and tighten or secure if needed.
___ 2. Check field piping for proper support and proper connection.
___ 3. Check unit belts for correct tension and alignment.
___ 4. Check unit electrical connections to the control boards and tighten or secure if needed.
___ 5. Remove all debris, tools and documents from unit area.
Liebert® CW™
100
Initial Startup Checks and Commissioning Procedure for Warranty Inspection
10.2.1 Inspect and Record
Main Fan hp: _________________________
Voltage: _________________________
Proper Belt Tension and Alignment: _________________________
Belt Size: _________________________
Motor Sheave: _________________________
Fan Pulley: _________________________
EC Plug Fan: Assemblies Tight and Secured (check one)
___ Fan secured in UP position
___ Fan secured in Down position
Filter Size: _________________________
Quantity: _________________________
10.3
Startup
1. Disconnect all power to the environmental control unit.
2. Tighten all electrical wiring connections on electric panel and at all major components, such as
compressors and motors that may have loosened during shipping.
3. Remove all line voltage fuses except the main fan fuses at the far right of the electric panel and
the control voltage fuses at the far left of the electric panel. For units supplied with circuit
breakers, open them instead of removing fuses.
4. Turn on electrical input power and check the line voltage on the main unit disconnect switch. Line
voltage must be within 10% of the nameplate voltage.
5. Turn ON the main unit disconnect switch and check the secondary voltage at transformer T1.
Voltage at T1 must be 24VAC, ±2.5VAC (check at TB1-1 and TB1-8). T1 voltage must not exceed
28VAC. Change the primary tap if necessary.
6. Push the ON button. Blower will start and the ON lamp will light.
7. If you do not want your unit to operate at factory default settings, manually set temperature
setpoints and sensitivity, alarms and other control functions. Refer to the Liebert iCOM® manual,
SL-18835, available at the Liebert Web site, www.liebert.com
8. Turn Off the main unit disconnect and main breaker. The unit On button should be Off.
9. Replace all fuses removed during Step 3 (or reset the circuit breakers).
10. Restore electrical power to the unit; turn ON the main unit disconnect switch.
11. Check the current draw on all line voltage components and match with the serial tag.
12. Push the ON button, putting the unit into operation.
13. Check for unusual noises and vibration.
14. Check all water lines for leaks.
15. Test all unit functions for proper operation.
Return the completed startup form to your local Emerson Network Power sales office.
10.4
Additional Considerations for Upflow Units
These units are manufactured with factory-supplied adjustable motor sheaves. Due to variations in
applications, a fixed motor pulley may be desired and can be substituted for the adjustable sheave
after obtaining and confirming the desired airflow. This will reduce vibration and wear on the belts
and pulleys. Consult your Emerson representative for more information.
101
Liebert® CW™
Troubleshooting
11.0 TROUBLESHOOTING
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect all local and remote electrical
power supplies before working within the unit.
Only properly trained and qualified personnel should perform service on these units. Lethal
voltage is present in some circuits. Use caution when troubleshooting with power on.
Disconnect and lock out power before replacing components. Use caution and standard
procedures when working with pressurized pipes and tubes.
NOTICE
Risk of improper control circuits. Can cause equipment damage.
When using jumpers for troubleshooting, always remove jumpers when maintenance is
complete. Jumpers left connected could override controls and cause equipment damage.
Table 9
Blower troubleshooting
Symptom
Blower will not start
Possible Cause
Check or Remedy
No main power
Check L1, L2 and L3 for rated voltage.
Blown fuse or tripped circuit
breaker (CB)
Check fuses or CBs to main fan.
Overloads tripped
Push reset button on main fan overload. Check amp. draw.
No output voltage from
transformer
Check for 24 VAC between P24-2 and P24-1. If no voltage,
check primary voltage.
Control fuse blown or circuit
breaker tripped
Check for 24 VAC between P4-4 and E1. If no voltage,
check for short. Replace fuse or reset circuit breaker.
Check for 24 VAC between P36-9 and P36-10. If voltage is
not present, R1 is not receiving power.
Blower runs but controls
will not operate
Relay R1 not making contact
(standard controls only)
Check air switch. Jumper P36-4 to P36-7 If R1 closes, air
switch is not closing (check for blower rotation, loose wiring
and pinched tubing.) Remove jumper.
Check for 24 VAC at R1 coil. If the voltage is present and R1
is not pulling, replace R1.
Table 10
Chilled water troubleshooting
Symptom
Possible Causes
Check or Remedy
Actuator Motors
No 24 VAC power to motor
Check for 24 VAC between P22-3 and P22-5 (open), or
P22-1 and P22-5 (closed).
Chilled water or hot
water/steam valve not
opening
Motor operates but valve won’t
open
Check linkage for adjustment and be sure that it is tight on
the valve.
No 24 VAC power to motor
Check linkage for adjustment and be sure that it is tight on
the valve.
No signal from control
Check DC voltage on printed circuit board in motor. Terminal
No. 1 is grounded and No. 3 is positive. DC voltage should
vary from 0.8 to 2.0 VDC or above as temperature control is
varied below room temperature on cooling valve or above
room temperature on heating valve.
Motor not working
Remove wires on terminal No. 1 and No. 3 from the motor
(do not short). With 24 VAC power from TR to TR jumper
terminal 1 and 2 on motor to drive open. Remove jumper to
drive closed, if motor fails to work, replace it.
Modulating Motors
Liebert® CW™
102
Troubleshooting
Table 11
Humidifier—steam generator troubleshooting
Symptom
False canister full
indication
Main 24 VAC fuse or
circuit breaker trips
Possible Cause
Check or Remedy
Check drain valve to ensure that it drains freely. Check
and replace if defective.
Foaming
Check water supply. If commercially softened,
reconnect to raw water supply. If connected to hot
water reconnect to cold water.
Shorts or loose connections
Check the wiring connections of the 24 VAC circuit.
Faulty circuit board
Replace the circuit board.
Verify that RUN/DRAIN switch is in the RUN position.
Unit ON, humidifier will
not operate
Contactor pulled in, but
no water enters
canister
Water enters canister,
but canister full circuit
activates at a low water
level
Check fuses or CBs and replace or reset if necessary.
Humidifier not receiving power
Make sure molex connector is securely plugged into
circuit board and that no wires art loose.
No water available to unit
Check external shut-off valves.
Clogged fill line strainer
Clean or replace fill line strainer.
Wiring breaks or loose connections
Check for faulty wiring and loose connections.
Faulty circuit board
Replace circuit board.
Foaming
Check drain valve and water supply.
Canister interface connections
incorrect
Check connection on component plate in humidifier
cabinet Terminal #1 on the square block interface
device must be connected to L2 of the power terminal
block. L2 must also be connected to the electrode
closest to the steam outlet port.
Verify that the red wire from terminal #2 on the
interface connects to the red top terminal on the
canister. This is the one farthest from the steam outlet
port and is the high-water sensor probe.
Full isolation has broken down
Remove red canister full wire from canister. If normal
operation resumes, canister must be replaced.
Remove the wire from terminal #3 on the interface. If
normal operation resumes, canister full interface must
be replaced.
Drain assembly not operating freely
Check and replace coil or valve if necessary.
Faulty circuit board
Replace circuit board
Canister full circuit does not activate
Check wiring of canister full interface. Replace circuit
board.
Cylinder full. Interface activated.
See similar symptoms above. Canister expired.
Replace canister.
Problem with fill water system
Water supply is not on. Fill valve problem. Drain valve
stuck open.
Humidifier amps reached 138% of full
load
Canister expired. Replace canister. DIP switch
settings changed with water in canister. Drain canister,
call Emerson Network Power Liebert Services.
Humidifier fill valve stuck open; check valve. Water
conductivity too high; check water conductivity/quality.
Contact Liebert Services.
DIP switches set incorrectly. Refer to Circuit Board
Adjustments on page 114
Mineral deposits obstruct drain valve
Check drain valve for obstructions and clean if
necessary.
Water enters canister,
but canister full circuit
activates at a low water
level
Canister fills but
overflows
Humidifier contactor is
not pulled in (to reset,
de-energize control
unit)
Red LED on humidifier
control board is on.
Humidifier contactor not
pulled in (to reset, deenergize control circuit)
Faulty solenoid
Check for magnetic field at coil.
Faulty circuit board
Replace circuit board.
103
Liebert® CW™
Troubleshooting
Table 11
Humidifier—steam generator troubleshooting (continued)
Symptom
Excessive arcing in the
canister
On cold startup,
canister fills, high-water
alarm activates and
humidifier fails to reach
full amperage after 24
hours
Table 12
Possible Cause
Check or Remedy
Drain valve clogged or defective
Verify that drain valve operates freely when activated.
Clean valve and replace coil or valve if defective.
Flush canister several times and replace if arcing
persists
Improper water supply
If water is commercially softened, reconnect humidifier
to raw water supply, drain canister and restart. If
connected to hot supply, reconnect to cold water.
Insufficient drain rate
Increase drain rate by adjusting % pot on circuit board
above the preset 87% (85%) to roughly 92% (90%).
Excessive iron content in water
Analyze iron cement of water. If it exceeds 0.1 mg/l,
install a filter to remove iron from water supply.
Conductivity of water too low
Turn the % pot to roughly 82% (80%). Restart
humidifier. If canister fails to reach FLA in 24 hours,
have water supply conductivity checked.
Fill solenoid not closing tightly
If humidifier returns to canister full condition, verity that
the fill solenoid closes tightly.
Humidifier—infrared troubleshooting
Symptom
Possible Cause
Check or Remedy
Check water supply.
Check fill valve operation
Humidifier pan not filling
Check drain stand pipe adjustment
Check for clogged waterline
Control not calling for humidity
Check monitor status
No humidification
Check visually. If contact is made, check line voltage
after contactor and fuses or CBs.
Humidity contact not pulling in
Check for open humidifier safety stat. Jumper between
terminals P35-6 and P35-5. If contactor pulls in,
replace safety. Remove jumper.
Replace bulb. Loosen lead on old bulb. Trim excess
lead length on new bulb to avoid shorts.
Humidifier bulb burned out
Table 13
Reheat troubleshooting
Symptom
Reheat will not operate;
contactor not pulling in
Reheat not operating,
contactor pulling in
Liebert® CW™
Possible Cause
Check or Remedy
Control not calling for heat
Check monitor status.
Reheat safety stat open
Jumper between terminals P34-1 and P34-2. If reheat
operates, safety is open. Remove jumper. Replace
safety.
Heater burned out
Turn off power and check heater continuity with Ohm
meter.
104
Maintenance
12.0 MAINTENANCE
For assistance, contact Emerson Network Power Liebert Services at 1-800-LIEBERT.
12.1
System Testing
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect all local and remote electrical
power supplies before working within the unit.
Potentially lethal voltages exist within this equipment during operation. Observe all cautions
and warnings on unit and in this manual. Failure to do so could result in serious injury or
death. Only qualified service and maintenance personnel should work with this equipment.
12.1.1 Environmental Control Functions
The performance of all control circuits can be tested by actuating each of the main functions. This is
done by temporarily changing the setpoints.
Cooling
To test the cooling function, set the setpoint to a temperature 10°F (5°C) below room temperature. A
call for cooling should be seen and the equipment should begin to cool. A high-temperature alarm may
come on. Disregard it. Return setpoint to the desired temperature.
Proportional Cooling
The Liebert iCOM® is capable of responding to changes in room conditions. These systems utilize
either a two or three-way valve activated by a proportioning motor. Refer to the Liebert iCOM user
manual, SL-18835, available at the Liebert Web site, www.liebert.com, for large or small display
operation and settings.
The Liebert iCOM will respond by positioning the valve proportionally to match the needs of the
room. Full travel of the valve takes place within the range of the sensitivity setting.
12.1.2 Electric Panel
The electric panel should be inspected for any loose electrical connections.
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect all local and remote electrical
power supplies before working within the unit.
Be sure that power to the unit is shut down before attempting to tighten any fittings or
connections.
Control Transformer and Fuses
The control system is divided into four (4) separate circuits. Fuses located on the transformer/fuse
board individually protect the control voltage circuits. If any of the fuses are blown, first eliminate
shorts, then use spare fuses supplied with unit. Use only type and size of fuse specified for your unit.
The small isolation transformer on the main control board supplies 24 volts to the electronics. The
transformer is internally protected. If the internal protector opens, the transformer/fuse board must
be replaced. Also check the control voltage fuse on the main control board before replacing the
transformer/fuse board.
Fan Safety Switch
For Liebert CW units, the Fan Safety Switch is in the low-voltage compartment and consists of a
diaphragm switch and interconnecting tubing to the blower scroll. The Fan Safety switch is wired
directly to the control circuit to deactivate the unit and activate the alarm system if airflow is
interrupted.
105
Liebert® CW™
Maintenance
Firestat
The optional firestat is a bimetal operated sensing device with a Normally Closed switch. This device
will shut down the entire unit when the inlet air temperature exceeds a preset point. It is connected
between terminals 1 and 2 at plug P39.
Smoke Detector
The optional smoke detector power supply is located on the base of the upflow units and at the top of
downflow units. It is constantly sampling return air through a tube. No adjustments are required.
Water Detection Sensor
! WARNING
Risk of fire or explosion. Can cause injury or death.
Do not use near flammable liquids or for flammable liquid detection.
Emerson manufactures a variety of water-detection systems, including point, zone and cable systems.
Follow the instructions supplied with your selected device for proper installation, adjustment and
maintenance.
Remote Shutdown
A connection point is provided for customer-supplied remote shutdown devices. Terminals 37 & 38 on
the terminal strip are jumpered when no remote shutdown device is installed. Refer to the unit’s
electrical schematic and the unit’s installation manual.
12.2
Filters
Filters are usually the most neglected item in an environmental control system. To maintain efficient
operation, they should be checked monthly and changed as required. Because replacement intervals
vary with environmental condition and filter type, each unit is equipped with a filter clog switch. This
warns of restricted airflow through the filter compartment by activating the Change Filter alarm.
• Turn power Off before replacing filters.
• Liebert CW filters can be replaced from either end by opening the end doors. On CW089, CW106
and CW114 units, filters can be replaced from the front. Liebert CW models CW146 and CW181
contain filters in a filter plenum that permits removing the filters from the front. Removing the
middle filters will allow you to remove the filters on the end. Install the new end filters first, then
the middle ones.
• Replacement filters are commercially available in several efficiencies. For Liebert CW units, refer
to the technical data manual, SL-18056, or other documentation for filter sizes.
• After replacing the filter(s), test the operation of the filter clog switch. Turn the adjusting screw
counter clockwise to trip the switch—this will energize the Change Filter alarm. To adjust the
switch:
1. With the fan running, set the switch to energize the light with clean filters. The unit panels must
all be in place and closed to accurately find this point.
2. Turn the adjusting knob one turn clockwise, or to the desired filter change point.
Liebert® CW™
106
Maintenance
12.3
Blower Package—Centrifugal Fans
Periodic checks of the blower package include: belt, motor mounts, fan bearings and impellers.
These units are manufactured with factory-supplied adjustable motor sheaves. Due to variations in
applications, a fixed motor pulley may be desired and can be substituted for the adjustable sheave
after obtaining and confirming the desired airflow. This will reduce vibration and wear on the belts
and pulleys. Consult your Emerson representative for more information.
12.3.1 Fan Impellers and Bearings
Fan impellers should be periodically inspected and any debris removed. Check to see if they are
tightly mounted on the fan shaft. Rotate the impellers and make sure they do not rub against the fan
housing.
Bearings used on the units are permanently sealed and self-lubricating. They should be inspected for
signs of wear when belts are adjusted. Shake the pulley and look for movement in the fan shaft. If any
excessive movement is noticed, bearings should be replaced. However, the cause of the wear must be
determined and corrected before returning the unit to operation.
12.3.2 Belts—Except with EC Fans
The drive belt should be checked monthly for signs of wear and proper tension. Pressing in on belts
midway between the sheave and pulley should produce from 1/2" to 1" (12 to 25mm) of movement.
Belts that are too tight can cause excessive bearing wear.
Belt tension is adjusted by raising or lowering the fan motor base. To adjust the motor, loosen (but do
not remove) the four motor mounting bolts. Turn adjustment bolt(s) on motor mounting base to adjust
belt tension or to raise motor to remove belts. Tighten motor bolts after adjustment. If belt appears
cracked or worn, it should be replaced with a matched belt (identically sized). With proper care, a belt
should last several years.
12.3.3 Electronic Variable Speed Drive (Inverter)
On large Liebert CW models, an optional, variable speed drive inverter is available. This packaged
unit is factory-set and should not require field adjustment. The variable speed drive saves power by
reducing blower speed to match unit load. If you suspect a problem with the inverter, first make sure
that the INTELLIGENT CONTROL method is selected at the microprocessor.
1. Turn off all power to the unit at the disconnect.
2. Open the unit accent panel and electric box cover.
3. Find the main fan motor wires. These are connected to the motor overload relay in the
high-voltage section of the electric box.
a. Mark motor wires to ensure they can be reconnected in the same order.
b. Disconnect motor wires at the load side of the motor overload relay.
c. Close the electric box cover.
4. Remove the right front vertical panel to gain access to the variable speed drive.
5. With the panel removed, restore power to the unit by turning the disconnect on.
6. Place the right front vertical panel back on the unit.
7. Reconnect the motor wires to the overload and close the electric box cover and unit accent panel.
8. Restore power at the disconnect.
12.4
Blower Package—EC Fans
12.4.1 Fan Impellers and Bearings
Fan impellers should be periodically inspected and any debris removed. Check to see if the impellers
can rotate freely and if the fan guards are still properly mounted for sufficient protection against
accidentally touching the impeller. Bearings used on the units are maintenance free. Consult the
factory for more information.
107
Liebert® CW™
Maintenance
12.4.2 Protective Features
Monitoring functions protect the motor against overtemperature of electronics, overtemperature of
motor and incorrect rotor position detection. With any of these failures, an alarm will display through
the Liebert iCOM® and the motor stops electronically. There is no automatic restart. The power must
be switched off for a minimum of 20 seconds once the motor is at a standstill.
The motor also provides locked rotor protection, undervoltage/phase failure detection and motor
current limitation. These conditions will display an alarm through the Liebert iCOM.
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect all local and remote electrical
power supplies before working within the unit.
When connecting the motor to the mains, dangerous voltages occur. Do not open the motor
within the first 5 minutes after disconnection of all phases.
Dangerous external voltages can be present at main fan terminal KL2 even with the motor
being turned off.
! CAUTION
Risk of hot surfaces. Can cause injury.
Wear thermally insulated gloves and a long-sleeved shirt when touching the electronics
housing or allow time for the housing to cool before replacing parts.
The electronics housing can get hot and can cause severe burns
! CAUTION
Risk of improper moving, lifting and handling. Can cause equipment damage or injury.
Only properly trained and qualified personnel should work on this equipment. Fan modules
weigh in excess of 100 pounds each and may require more than one person or a mechanical
lifting device to raise or lower the fan(s) safely. Use proper lifting techniques and wear
protective clothing, gloves, shoes and head gear to avoid injury and dropping the fan module
during removal.
NOTICE
Risk of improper installation. Can cause equipment damage. Only a properly trained and
qualified technician should install or open this motor.
Use 60/75°C copper wire only. Use Class 1 wires only.
12.5
Humidifier
12.5.1 Infrared Humidifier
During normal humidifier operation, deposits of mineral solids will collect in the humidifier pan and
on the float switch. These must be cleaned periodically to ensure proper operation. Frequency of
cleaning must be locally established because it depends on humidifier usage and local water quality.
A spare pan is recommended to reduce maintenance time at unit. The Liebert autoflush system can
greatly increase the time between cleanings, but does not eliminate the need for periodic checks and
maintenance (see the Liebert iCOM user manual, SL-18835, available at the Liebert Web site,
www.liebert.com, for autoflush setup). To help reduce excessive scaling in locations with difficult
water quality, the use of Vapure is recommended (contact your local Emerson representative).
Liebert® CW™
108
Maintenance
12.5.2 Cleaning Humidifier Pan and Float Switch
Before turning off unit:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
With the unit operating, remove call for humidification at the Liebert iCOM® control.
Let the blower operate 5 minutes to allow the humidifier and water to cool.
If the unit has a condensate pump, turn the unit Off at the Liebert iCOM control.
Pull out the humidifier standpipe in pan.
Inspect the O-ring (replace if necessary).
Let the pan drain and the condensate pump operate (if applicable).
Disconnect power from the unit.
Disconnect the drain coupling from the bottom of the pan.
Remove the thermostat from the bottom of the pan and retaining screws from sides of pan.
Slide pan out.
Loosen scale on the side and bottom of the pan with a stiff nylon brush or plastic scraper.
Flush with water.
Carefully clean the scale from the float switch (make sure to reinstall correctly; see Figure 88).
Reinstall the pan, thermostat, standpipe, drain coupling and screws into the humidifier.
Operate the humidifier and check for leaks.
Figure 88 Correct orientation of float switch
Correct Switch Orientation
Incorrect Switch Orientation
DPN000996
Rev. 0
109
Liebert® CW™
Maintenance
12.5.3 Changing Humidifier Lamps
NOTE
Touching quartz lamps with bare hands will severely shorten bulb life. Skin oils create hot
spots on lamp surface. Wear clean cotton gloves when handling lamps.
1. Remove the humidifier pan (see 12.5.2 - Cleaning Humidifier Pan and Float Switch, Steps 1
through 10).
2. Disconnect power from the unit.
3. At the humidifier, remove the screws and cover from the high-voltage compartment.
4. Disconnect one end of the purple jumper wires.
5. Using a continuity meter, locate the burned-out lamp.
6. Remove the lamp brackets under the lamps.
7. Loosen the two screws securing the lamp lead wires to the junction block.
8. Pull the bulb straight down and discard it.
9. Wrap the lead wires once around the new lamp’s metal ends. This will support the lamp and allow
for thermal expansion. Insert the lead wires into the junction block and torque the screws to 30
in-lb.
10. Reassemble by reversing Steps 1 through 9.
Figure 89 Infrared humidifier lamps
Infrared Bulbs
12.6
Steam Generating Humidifier
The humidifier drains and refills to maintain a current setpoint and alert the operator when the
humidifier canister needs to be replaced. The humidifier is located in the lower section of upflow
units. In downflow units, the humidifier is in the middle section.
Figure 90 Steam generating humidifier
Liebert® CW™
110
Maintenance
Operation
NOTE
Numbers and percentages within parentheses in the following paragraphs refer to circuit
board settings for downflow models CW106 and CW114.
1. During startup, when the humidity control calls for humidification, the fill valve opens and allows
water to enter the canister. When the water level reaches the electrodes, current flows and the
water begins to warm. The canister fills until the amperage reaches the setpoint and the fill valve
closes. As the water warms, its conductivity increases and the current flow, in turn, rises. If the
current reaches 115% of the normal operating current, the drain valve opens and drains some of
the water out of the canister. This reduces electrode contact with the water and lowers the
current flow to the amperage setpoint. Boiling soon commences, and the canister operates
normally.
2. If the conductivity of the water is low, the canister fills and the water level reaches the canister
full electrode before the current setpoint is reached. The humidifier stops filling to prevent
overflow. Boiling should commence in time. As water is boiled off, the mineral concentration in
the canister increases and current flow also increases. The canister eventually reaches full output
and goes to normal operation. No drain is permitted until then.
3. When full output is reached the circuit board starts a time cycle which is factory-set at 60 (84)
seconds. During this repeating time cycle, the fill valve will open periodically to replenish the
water being boiled off and maintain a “steady state” output at the setpoint.
4. After many cycles, the mineral concentration in the canister becomes too high. When this occurs,
the water boils too quickly. As the water quickly boils off and less of the electrode is exposed, the
current flow decreases. When the current crosses the low threshold point before the end of the
time cycle, the drain valve opens, draining the mineral-laden water out and replacing it with
fresh water. This lowers the mineral concentration and returns the canister to “steady state”
operation and prolongs canister life. The frequency of drains depends on water conductivity.
5. Over a period of time (usually between 500 and 1500 hours depending on water quality), the
electrode surface will become coated with a layer of insulating material, which causes a drop in
current flow. As this happens, the water level in the canister will slowly rise exposing new
electrode surface to the water to maintain normal output. Eventually, the steady state water level
will reach the canister full electrode and indicate so by activating the canister full alarm and
opening the humidifier contactor. At this point, all of the electrode surface has been used up and
the canister must be replaced.
6. After the entire electrode surface has been coated, the output will slowly begin to fall off. This
usually occurs in the last several hours of electrode life and should allow enough time to schedule
maintenance. During these last hours, the mineral concentration can increase. If the mineral
concentration is too high, arcing can occur. If the electrodes start to arc, turn off the humidifier
immediately and replace the canister with the identical part.
Controls
The humidifier RUN/DRAIN switch is located in the unit low-voltage compartment for most models
(in the humidifier assembly for models CW106 and CW114). This switch should be in the RUN
position when the humidifier is in normal operation; it should be in the DRAIN position when a
manual drain for service is required. The electronic control board for the humidifier is located in the
same area as the humidifier RUN/DRAIN switch. When the main unit is energized, power is available
to the humidifier circuits.
Figure 91 Run/drain switch
111
Liebert® CW™
Maintenance
Replacing the Canister
See Step 5 of Operation in 12.6 - Steam Generating Humidifier for indications that a canister
may need to be replaced.
To replace the canister:
1. Turn off the humidifier by lowering the humidity setpoint below the ambient humidity level.
Record the original setpoint.
2. Place the RUN/DRAIN switch in the DRAIN position to drain the water from the canister.
3. Return the RUN/DRAIN switch to the RUN position after the canister has drained.
! WARNING
Risk of humidifier canister meltdown, smoke and fire. Can cause fire suppression system
activation, fire and smoke alarm activation, serious equipment and building damage, injury
and death.
Using a humidifier canister that has reached the end of it’s service life can be extremely
hazardous. If the canister cannot be replaced immediately at the end of life condition, turn Off
the power and water supply to the humidifier and remove the canister until a replacement
canister can be installed.
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect all local and remote electrical
power supplies before working within the unit.
To avoid a shock hazard, all power to the unit must be disconnected before proceeding with
the canister replacement procedure.
! CAUTION
Risk of hot humidifier canister and steam hose. Can cause injury. Allow time for the
humidifier to cool before replacing parts.
4. Turn Off the power at the main unit.
5. Remove the cover from the humidifier cabinet
6. For all models except CW106 and CW114, refer to the replacement instructions that accompany
the replacement kit 153315P1 and P2.
7. For models CW106 and CW114, locate the power wires to the steam canister. Make note of the
wiring configuration before removing any wires. Refer to the schematic on the unit. Slide the
rubber boot back to expose the connections. Remove the three power wires and the canister-full
wires at Terminals 1, 2 and 3. Do not loosen the screws that secure the electrodes.
8. For all models, use a screwdriver to remove the hose clamps that secure the drain and overflow
hoses from the canister ports.
9. Loosen the fill line compression fitting and remove the tube from the input canister port.
10. Loosen the steam outlet hose clamps and slide the steam hose away from the canister fitting.
Release the canister clamp along the base of the canister.
11. The canister is now ready to be removed.
On downflow units: Slide the humidifier cabinet bottom straight out toward you and drop the
canister through the bottom of the cabinet.
On all other units: Pull the canister straight out of the cabinet toward you.
12. Replace the canister with the part indicated in the following table.
Table 14 Humidifier canister part numbers
Capacity
Unit Model
All except below
CW106 CW114
Part Number
Voltage
200-230
153315P2
136799P1
136799P2
380-575*
153315P1
200-480
575
* Note: 575V units have a step-down transformer included with unit.
Liebert® CW™
112
lb/hr
kg/hr
11 or 22
5 or 10
22
22
10
10
Maintenance
13. Replace the canister by reversing the above procedure. Make special note of the following:
NOTE
When reconnecting the power wiring, follow exactly the instructions included with kit
153315P1 and P2 or the unit electrical schematic with canisters 136799P1 and P2.
When replacing the canister, always check the fill and drain solenoids for proper operation
Table 15
Faults—canister generator humidifier
Priority
Name
LED Indication
Description
1
Over Current
Solid
Humidifier Lockout
2
Fill Valve
2 second flash
Humidifier Lockout
3
End of Life
4 second flash
Humidifier Lockout
4
Fail to Make Capacity
1 second flash
Indicate only
Fault Descriptions
Overcurrent—Operating current exceeds present limit
Fill Valve—Continuously energized valve exceeds preset limit
End of Life—Drain count limit exceeded in a 24-hour period
Fail to Make Capacity—Does not reach operational current within initial 24 hours
Test Points
TP1—Time Cycle Pot
1 VDC = 60 seconds
TP2—Low Drain Pot
3 VDC = 80%
TP3—Capacity Pot
3.5 VDC = 85%
TP5—RT Capacity
1 VDC = 100%
113
Liebert® CW™
Maintenance
Circuit Board Adjustments
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect all local and remote electrical
power supplies before working within the unit.
Circuit board adjustment should be performed by properly trained and qualified personnel
only. Hazardous voltages are present in the equipment throughout the procedure. Use
extreme caution. If desired, power may be disconnected prior to the procedure.
NOTE
Numbers and percentages within parentheses in the following paragraphs refer to circuit
board settings for downflow models CW106 and CW114.
Humidifier operation is governed by the humidifier control board. This board is located in the lower
right area of the panel in the control section of the unit, or in the humidifier compartment on models
CW106 and CW114. There are two potentiometers mounted on the board. These pots can be used to
adjust for extreme water conductivity conditions and capacity.
The “%” pot controls the amperage at which the drain will energize. The pot is clearly marked in
percentages. This adjustment is factory-set, which indicates that the unit will drain when the
amperage falls off of the capacity setpoint. Raising the value increases the frequency of drain cycles.
Lowering the value decreases the frequency of drain cycles. The frequency should be increased for
highly conductive water and decreased for less conductive water. If adjustment is necessary and a
change of three to four percent in either direction does not permit normal operation of the unit,
consult your Liebert supplier.
The pot marked “SEC” controls the duration of the drain cycle. The pot is clearly marked in seconds.
This adjustment is factory-set at 60 (84) seconds and should not be readjusted without consulting
your Liebert supplier.
Table 16
Steam generating humidifier capacity
60 Hz Models
50 Hz Models
Capacity
lb/hr (kg/hr)
CW026, CW038, CW041
CW026, CW038, CW041
11 (5)
CW051, CW060, CW076,
CW084, CW106, CW114
CW051, CW060, CW076,
CW084, CW106, CW114
22 (10)
! WARNING
Risk of electric shock and slipping hazard from incorrect DIP switch settings. Can cause
injury or death.
The DIP switches must be set exactly as indicated in Table 17. Failure to correctly set the
DIP switches may result in an electrical or water hazard.
The DIP switches are used to set the capacity of the humidifier. These are set at the factory and
should not be changed. Refer to Table 16 for the capacity of your unit. Find your unit voltage and
capacity in Table 17 to determine the correct DIP switch settings for your humidifier. A
potentiometer (R40) is used to regulate the capacity of the humidifier. This adjustment is factory-set
fully clockwise to 100%. It can be used to reduce humidifier capacity, but should never be used to raise
the capacity above the capacity for your model. Turn the adjustment counterclockwise to reduce your
capacity. The minimum setting is approximately 50% of the DIP switch setting.
Liebert® CW™
114
Maintenance
Figure 92 Steam generating humidifier control board
GT-421 V*.*
Drain Tempering
Shunt
YYDDD
ON OFF
Fault LED
TP6
TP7
DIP Switch
Down (Off), Up (On)
Capacity
Transformer
TP5
TP3
P3
TP2
Low Drain
Microprocessor
P2
TP1
Time Cycle
P1
183116
Rev. 2
Table 17
DIP switch settings for steam generating humidifier
Rated Values
Unit Rated
Voltage
Capacity
SW1
SW2
SW3
SW4
Voltage
AMP Set Pt
200/208
11
Off
On
Off
On
208
12.6
200/208
22
On
Off
On
On
208
23.8
230
11
Off
Off
Off
On
240
10.5
230
22
Off
Off
On
On
240
20.3
380/400/415
11
On
On
Off
Off
400
6.3
380/400/415
22
Off
On
On
On
400
12.6
460
11
On
Off
Off
Off
480
5.5
460
22
Off
Off
Off
On
480
10.5
575*
11
Off
Off
Off
Off
575
4.2
575*
22
Off
On
Off
On
575
9.8
*The values are only suitable in models CW106D and CW114D. All other models use a 575V-to-460V step-down
transformer and therefore use the 460V settings.
Source: 183116, Rev. 2
115
Liebert® CW™
Maintenance
12.7
Condensate Drain and Condensate Pump Systems
12.7.1 Condensate Drain
Check and clear obstructions in tubing during routine maintenance.
12.7.2 Condensate Pump
•
•
•
•
•
•
Disconnect power to unit using disconnect switch.
Disconnect power to unit using disconnect switch.
Check and clear obstructions in gravity lines leading to condensate pump.
Remove sump and clean with a stiff nylon brush and flush with water.
Inspect and clear clogs in discharge check valve and float mechanism.
Reassemble and check for leaks.
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect all local and remote electrical
power supplies before working within the unit.
The Liebert iCOM® microprocessor does not isolate power from the unit, even in the “Unit Off”
mode. Some internal components require and receive power even during the “unit off” mode of
the Liebert iCOM control.
12.8
Facility Fluid and Piping Maintenance
Facility water and glycol quality remain a requirement throughout the life of the piping system. Fluid
and piping system maintenance schedules must be established and performed. A local fluid
maintenance program must be established that will evaluate fluid chemistry and apply necessary
treatment.
A periodic leak inspection of facility and unit fluid piping is recommended. Refer to 7.2.1 Requirements of Systems Using Water or Glycol.
Liebert® CW™
116
Maintenance
12.9
HVAC Maintenance Checklist
Inspection Date
Job Name
Indoor Unit Model #
Indoor Unit Serial Number #
Room Temperature/Humidity
°
%
Ambient Temperature
°
Filters
___ 1. Check/replace filters
___ 2. Grille area unrestricted
___ 3. Wipe section clean
___ 4. Coil clean
Blower Section
___ 1. Blower wheels free of debris
___ 2. Check belt tension and condition on centrifugal blower units (replace if needed)
___ 3. Check bearings
___ 4. Check sheave/pulley on centrifugal blower units (replace if worn)
___ 5. Check motor mount
___ 6. Motor amp draw
L1__________________ L2 __________________ L3______________
____ Compare to nameplate amps
Reheat
___ 1. Inspect elements
___ 2. Check wire connections (inside reheat box)
___ 3. Reheat amp draw
___ a. #1
___ a. #2
___ a. #3
Steam Generating Humidifier
___ 1. Check drain valve/drain lines/trap for clogs
___ 2. Check water make-up valve and all hoses for leaks
___ 3. Clean strainer
___ 4. Replace humidifier bottle if necessary
___ 5. Check operation of humidifier
___ 6. Humidifier amp draw
L1 ______________ L2 _______________L3__________________
Infrared Humidifier
___ 1. Check drain lines and trap for clogs
___ 2. Check/clean pan for mineral deposits
___ 3. Clean reflector
___ 4. Check water make-up valve for leaks
___ 5. Check humidifier lamps (replace if burnt out)
___ 6. Check wire connections (inside humidifier box)
___ 7. Humidifier amp draw
L1 ______________ L2 _______________L3__________________
117
Liebert® CW™
Maintenance
Drain Piping
___ 1. Check for free running drain system
___ 2. Clear out obstructions and material buildup on tubing walls
___ 3. Check for leaks
___ 4. Check for tubing kinks or damage
Condensate Pump
___ 1. Check for debris in sump
___ 2. Check operation of float(s) (free movement)
Electrical Panel
___ 1. Check fuses
___ 2. Check contactors for pitting
___ 3. Check wire connections
Controls
___ 1. Check/Verify Control Operation (Sequence)
___ 2. Check humidifier high-water alarm operation
___ 3. Check operation of the air safety switch
___ 4. Check setting/operation of the filter clog switch
___ 5. Check/test changeover device(s)
___ 6. Check/test water detection device(s)
Notes _______________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
Signature ___________________________________________________________________________________
Company ____________________________________________________________________________________
Make photocopies for your records. Compare readings / information to previous maintenance
worksheet. To locate your local Emerson representative for Liebert-engineered parts, check the
Liebert Web site: www.liebert.com or call 1-800-LIEBERT.
Liebert® CW™
118
Installing Liebert CW300 and Liebert CW400
APPENDIX A - INSTALLING LIEBERT CW300 AND LIEBERT CW400
Liebert CW300 and Liebert CW400 models ship in multiple components that must be assembled in
the field. These components include the front and rear modules, filter plenum and optional floor
stands. Follow all instructions to reduce the risk of damage to property, personnel and equipment.
This appendix is to be used only in conjunction with the preceding portions of this user manual.
! WARNING
Risk of electric shock. Can cause injury or death. Disconnect all local and remote electrical
power supplies before working within the unit.
Only properly trained and qualified personnel should install or perform service on these units.
Lethal voltage is present in some circuits. Use caution when troubleshooting with power On.
Disconnect and lock out power before replacing components. Use caution and standard
procedures when working with pressurized pipes and tubes.
! WARNING
Risk of mishandling heavy fan assembly(s) and plenum. Can cause equipment damage, injury
or death. Attach the fan assembly(s) and plenum to the unit only as described in these
instructions.
! CAUTION
Risk of sharp edges and heavy parts. Can cause injury and equipment damage.
A minimum of two properly trained and qualified personnel are required to install the fan
assembly(s) and plenum.
Wear OSHA approved safety headgear, gloves, shoes, and glasses when installing the fan
assembly(s) and plenum.
Equipment used in handling/lifting, and/or installing the fan assembly(s) and plenum must
meet OSHA requirements. Use handling/lifting equipment rated for the weight of the fan
assembly(s) and plenum. Use ladders rated for the weight of the fan assembly(s) and plenum
and technicians if used during installation.
Refer to handling/lifting, and/or installation equipment operating manual for manufacturer's
safety requirements and operating procedures.
Refer to Table 18 for component weights, and to Table 19 for required parts common to
installation of any Liebert CW300 or Liebert CW400 unit.
Table 18
Liebert CW300 and Liebert CW400 component parts and weights
Component
Part Number
Weight, lb (kg)
CW300 Front Module
CW300 Rear Module
CW400 Front Module
CW400 Rear Module
Floor Stand—24" Tall
Complete Assembly Part #
Rear Subassembly Part #
Front Subassembly Part #
Floor Stand—30" Tall
Complete Assembly
Rear Subassembly
Front Subassembly
Floor Stand—36" Tall
Complete Assembly
Rear Subassembly
Front Subassembly
CW30ADC_ _ 1 _ _ _ _
CW30BDC_ _ 1 _ _ _ _
CW40ADC_ _ 1 _ _ _ _
CW40BDC_ _ 1 _ _ _ _
2900 (1315)
2900 (1315)
2900 (1315)
2900 (1315)
304394G24
304394G24R
304394G24F
800 (363)
400 (181)
400 (181)
304394G30
304394G30R
304394G30F
900 (408.)
450 (204)
450 (204)
304394G36
304394G36R
304394G36F
1000 (453)
500 (227)
500 (227)
119
Liebert® CW™
Installing Liebert CW300 and Liebert CW400
Table 19
Table 2 - Liebert CW300 and Liebert CW400 Assembly Parts
Component
Part Number
QTY
Washer, Plain Flat 5/16”
S12-1300
4
Screw, 5/16-18 x 1.50 Fb Cash D2
195508P1
4
S12-1300
11
S-1110
11
195577P1
11
Parts for Securing Front and Rear Floor Stand
Parts for Securing Front and Rear Frame
Washer, Plain Flat 5/16”
Washer, Lock Z Extern Tooth 5/16"
Screw, 5/16-18 x 1.00 Bhscs Zb
Parts for Securing Front and Rear Fan Decks
A.1
Screw, 5/16-18 x 1.50 Fb Cash D2
195508P1
3
Washer, Lock Z Extern Tooth 5/16"
S-1110
3
EQUIPMENT INSPECTION AND HANDLING
The Liebert CW300 and Liebert CW400 front and rear modules are packaged in the same manner as
all other Liebert CW units. See 4.0 - Equipment Inspection and Handling for details about
unpacking, inspecting and handling the modules.
A.2
LIEBERT CW300 AND LIEBERT CW400 INSTALLATION PREPARATION
1. Move the Liebert CW to its installation location and unpack the components.
2. Verify that the fan motors’ voltage rating is appropriate for the marked unit voltage rating.
A.3
LIEBERT CW300 AND LIEBERT CW400 INSTALLATION PROCEDURES
1. If included on order, install the floor stand for the rear section of the unit.
2. Refer to Table 18 to verify that the correct floor stand component is being installed.
3. Verify that the floor stand is in the correct position and that the uppermost horizontal surface is
level in all directions.
4. Adjust legs to achieve uniform level across all directions if not level.
5. Remove side panels of rear module.
6. Refer to Table 18 to verify that the correct module is being installed.
7. Install rear section of cabinet on the floor stand.
Do not remove the rear panel if there will be no access for re-installation after the rear module
has been placed on the floor stand.
8. Secure the rear module to rear floor stand using the procedures shown in this section of manual.
Figure 93 shows rear unit and rear floor stand after completion of this step. Some components are
removed for clarity.
Liebert® CW™
120
Installing Liebert CW300 and Liebert CW400
Figure 93 Rear floor stand and rear unit mounted on floor stand
Rear Floor Stand
Rear Unit Mounted on Floor Stand
9. If unit application calls for EC fans to be lowered, lower the EC fans in the rear unit as detailed in
5.1 - Lowering and Removing EC Fans—Downflow Units Only.
NOTICE
Risk of improperly lowering fans. Can cause damage to the Liebert CW. All instructions in
5.1 - Lowering and Removing EC Fans—Downflow Units Only must be followed when
lowering the EC fans to prevent damage.
NOTE
The Liebert CW300 and Liebert CW400 rear floor stand employ a lengthwise channel for
mounting of the jack that differs from other Liebert CW units. Figure 94 shows this channel.
All other instructions are the same as in 5.1 - Lowering and Removing EC Fans—
Downflow Units Only.
Figure 94 Rear floor stand jack
Floor Stand
Jack Handle
Floor Stand Jack
10. 4.Install front floor stand.
a. Verify that the floor stand is in the correct position and that the uppermost horizontal surface
is level in all directions.
b. Adjust legs to achieve uniform level across all directions if not level.
c. Secure the front and rear floor stand section with the provided bolts.
The bolts are to be installed as shown in Figure 95.
121
Liebert® CW™
Installing Liebert CW300 and Liebert CW400
Figure 95 Floor stand bolt locations
Floor Stand Bolt
Locations
Floor Stand
Bolt Locations
11. Remove the front module panels and field service plates that are bolted under the front panels.
12. Install the front section of cabinet on the front floor stand.
13. Secure the front and rear unit modules together with the provided bolts, nuts and washers in the
locations shown in Figure 96.
Figure 96 shows installation on the right (non-valve) side, but bolt locations are typical for both
sides.
Figure 96 Module bolt locations
Bolt Connection Point
(Typical of both sides)
Bolt Connection Point
(Typical of both sides)
Rear of Liebert CW
Right Side of Liebert CW
Liebert® CW™
122
Installing Liebert CW300 and Liebert CW400
14. 6.Lower the front module EC fans as detailed in 5.1 - Lowering and Removing EC Fans—
Downflow Units Only.
NOTICE
Risk of improperly lowering fans. Can cause damage to the Liebert CW. All instructions in
must be followed when lowering the EC fans to prevent damage.
NOTE
The Liebert CW300 and Liebert CW400 rear floor stand employ a lengthwise channel for
mounting of the jack that differs from other Liebert CW units. Figure 94 shows this channel.
All other instructions are the same as in 5.1 - Lowering and Removing EC Fans—
Downflow Units Only.
15. After the fans have been lowered, secure the front and rear module fan decks together with the
provided nuts, bolts and washers.
If the site-specific application requires that the EC fans be employed inside the unit, the fans
should be raised before proceeding. To do so, reverse the order of instructions 5.1 - Lowering
and Removing EC Fans—Downflow Units Only.
Figure 97 Fan deck bolt locations
Fan Deck Bolt
Locations
16. Connect the fan wire harnesses for the rear module to terminals in the junction box behind the
piping in the left rear of the front unit. The wires are marked with hot stamps matching labels in
the junction box. Figure 98 shows a detail of the wire harness routing point and the junction box
location. Figure 99 shows a detail of the junction box and the termination locations.
123
Liebert® CW™
Installing Liebert CW300 and Liebert CW400
Figure 98 Wire harness routing point
Wire Harness
Routing Point
Junction Box
Liebert® CW™
124
Installing Liebert CW300 and Liebert CW400
Figure 99 Wire harness junction box detail
Low-Voltage
Connection
Entrance
High-Voltage
Connection
Entrance
Low-Voltage
Terminal
Strips
High-Voltage
Motor Terminal
Strips
High-Voltage THD and
Condensate Pump
Terminal Strips
17. Route the wire harness from the valve actuators and in the rear unit through hole provided for
harnesses to the harness on the valve actuator in the front unit and plug the harness in.
18. The remaining standard installation instructions for a CW181 apply for the wiring and piping
connections; refer to 6.0 - Electrical Connections and 7.0 - Piping.
125
Liebert® CW™
Installing Liebert CW300 and Liebert CW400
Notes
Liebert® CW™
126
COMPLIANCE WITH EUROPEAN UNION DIRECTIVES
Liebert Corporation
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
USA
Il Produttore dichiara che, se munito di marchio CE, il prodotto è conforme alle direttive dell'Unione
europea:
The Manufacturer hereby declares that this product, when bearing the CE mark, conforms to the
European Union directives:
Der Hersteller erklärt hiermit, dass das vorliegende Produkt, sollte es die CE-Kennzeichnung tragen, den
folgenden Richtlinien der Europäischen Union entspricht:
Le fabricant déclare par la présente que ce produit, portant la marque CE, est conforme aux directives
de l'Union européenne :
El fabricante declara por la presente que si este producto lleva el marcado CE es conforme con las
directivas de la Unión Europea:
O fabricante declara por este meio que este produto, quando ostenta a marca CE, está em
conformidade com as directivas da União Europeia:
Tillverkaren tillkännager härmed att den här produkten, när den är CE-märkt, överensstämmer med
EU:s direktiv:
De fabrikant verklaart hierbij dat dit product, indien het van de CE-markering is voorzien, conform de
EU-richtlijnen is:
Valmistaja vakuuttaa täten, että mikäli tuotteessa on CE-merkintä, se täyttää seuraavien EU-direktiivien
vaatimukset:
Produsenten erklærer herved at dette produktet, når det er CE-merket, er i samsvar med EU-direktiver:
Producenten erklærer hermed, at dette produkt overholder EU's direktiver, når det bærer CE-mærket:
Ο Κατασκευαστής δηλώνει ότι το προϊόν αυτό, το οποίο φέρει σήμανση CE, είναι σύμμορφο με τις
οδηγίες της Ε.Ε.:
2006/42/EC; 2004/108/EC; 2006/95/EC; 97/23/EC
Ensuring The High Availability
Of Mission-Critical Data And Applications.
Emerson Network Power, a business of Emerson (NYSE:EMR),
is the global leader in enabling Business-Critical Continuity™
from grid to chip for telecommunication networks, data centers,
health care and industrial facilities. Emerson Network Power
provides innovative solutions and expertise in areas including
AC and DC power and precision cooling systems, embedded
computing and power, integrated racks and enclosures,
power switching and controls, infrastructure management,
and connectivity. All solutions are supported globally by local
Emerson Network Power service technicians. Liebert AC power,
precision cooling and monitoring products and services
from Emerson Network Power deliver Efficiency Without
Compromise™ by helping customers optimize their data center
infrastructure to reduce costs and deliver high availability.
Technical Support / Service
Web Site
www.liebert.com
Monitoring
liebert.monitoring@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Single-Phase UPS & Server Cabinets
liebert.upstech@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Three-Phase UPS & Power Systems
800-543-2378
Outside North America: 614-841-6598
Environmental Systems
800-543-2778
Outside the United States: 614-888-0246
Locations
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
+39 049 9719 111
Fax: +39 049 5841 257
Asia
29/F, The Orient Square Building
F. Ortigas Jr. Road, Ortigas Center
Pasig City 1605
Philippines
+63 2 687 6615
Fax: +63 2 730 9572
While every precaution has been taken to ensure the accuracy
and completeness of this literature, Liebert Corporation assumes no
responsibility and disclaims all liability for damages resulting from use of
this information or for any errors or omissions.
© 2009 Liebert Corporation
All rights reserved throughout the world. Specifications subject to change
without notice.
® Liebert is a registered trademark of Liebert Corporation.
All names referred to are trademarks
or registered trademarks of their respective owners.
SL-18057_REV5_08-13
Emerson Network Power.
The global leader in enabling Business-Critical Continuity™
AC Power
Connectivity
Embedded Computing
Embedded Power
DC Power
Infrastructure Management & Monitoring
Outside Plant
Power Switching & Controls
Precision Cooling
EmersonNetworkPower.com
Racks & Integrated Cabinets
Services
Surge Protection
Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks of Emerson Electric Co. or one of its affiliated companies.
©2009 Emerson Electric Co.