Sharp XV-Z200E Specifications

XV-Z200E
XV-Z200E
PROJECTOR
PROJEKTOR
PROJECTEUR
PROJEKTOR
PROYECTOR
PROIETTORE
PROJECTOR
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
BRUKSANVISNING
MANUAL DE MANEJO
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
SHARP CORPORATION
Printed on 100% post-consumer recycled paper.
Gedruckt auf 100% wiederverwertungs Papier.
Imprimé sur 100% de papier recyclé.
Utskrift på återvunnet papper av 100% återvunnet material.
Impreso en 100% de papel reciclado de postconsumo.
Stampato su carta riciclata al 100%.
Gedrukt op 100% kringlooppapier.
XV_Z200E_E_Hyo1_4.p65
1
Printed in Japan
In Japan gedruckt
Imprimé au Japon
Triykt i Japan
Impreso en Japón
Stampato in Giappone
Gedrukt in Japan
TINS-B007WJZZ
03P11-JWM
03.10.30, 13:12PM
ENGLISH .............
-1 –
-70
DEUTSCH ............
-1 –
-70
FRANÇAIS ...........
-1 –
-70
SVENSKA ............
-1 –
-70
ESPAÑOL ............
-1 –
-70
ITALIANO .............
-1 –
-70
NEDERLANDS ....
-1 –
-70
This equipment complies with the requirements of Directive 89/336/EEC and 73/23/EEC as amended
by 93/68/EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit
Änderung 93/68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées
par la directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/
EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC come emendata
dalla direttiva 93/68/EEC.
Η εγκατάσταση αυτή ανταποκρίνεται στις απαιτήσεις των οδηγιών της Ευρωπαϊκής Ενωσης 89/
336/ΕΟΚ και 73/23/ΕΟΚ, #πως οι κανονισµοί αυτοί συµπληρώθηκαν απ# την οδηγία 93/68/ΕΟΚ.
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão
corrigida pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por
medio de la 93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras
av 93/68/EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/
68/EEC.
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse.
or
and of
Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
the same rating as above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut
off the mains plug and fit an appropriate type.
ASA
DANGER
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and
disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a
serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow
: Earth
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is
or coloured green or green-and-yellow.
marked by the letter E or by the safety earth symbol
• The wire which is coloured blue must be connected to the terminal which is marked with the letter N
or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L
or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
XV_Z200E_E_pi_ii.p65
1
03.10.30, 13:12PM
Before using the projector, please read this operation manual carefully.
Introduction
Introduction
ENGLISH
IMPORTANT
For your assistance in reporting the loss or theft of your
Projector, please record the Serial Number located on
the bottom of the projector and retain this information.
Before recycling the packaging, please be sure that
you have checked the contents of the carton thoroughly
against the list of “Supplied accessories” on page 12.
WARNING:
Model No.: XV-Z200E
Serial No.:
Intense light source. Do not look into the beam or view it directly. Be especially careful that children
do not look directly into the beam.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to
rain or moisture.
CAUTION:
To reduce the risk of electric shock, do not remove cabinet. No user-serviceable parts are inside.
Refer servicing to qualified service personnel.
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.
During normal operation, when putting the projector into the standby mode always use the STANDBY button on the
projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
-1
XV_Z200E_E_p01_03.p65
1
03.10.30, 13:13PM
Caution Concerning the Lamp Replacement
There is potential glass particles hazard if the lamp ruptures.
LAMP REPLACEMENT
CAUTION
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.
HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE
REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP
UNIT TYPE BQC-XVZ200++1 ONLY. UV RADIATION : CAN CAUSE
EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.
HIGH PRESSURE LAMP : RISK OF EXPLOSION.
POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS
RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.
PRECAUTIONS A OBSERVER LORS
DU REMPLACEMENT DE LA LAMPE.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.
L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE
1 HEURE AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-XVZ200++1.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.
LAMPE A HAUTE PRESSION : RISQUE D’EXPLOSION.
DANGER POTENTIEL DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE.
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
WARNING:
Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments.
Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile
the contents thereof.
-2
XV_Z200E_E_p01_03.p65
2
03.10.30, 13:13PM
Contents
Introduction
Introduction
Using the “Options” Menu ............................... 51
Contents ............................................................... 3
IMPORTANT SAFEGUARDS ............................... 4
Quick Guide ......................................................... 7
Part Names .......................................................... 8
Operating the Remote Control ......................... 11
Accessories ....................................................... 12
Connections & Setup
Connecting the Projector to Other Devices .... 14
Connecting the Power Cord ................................... 14
Connecting to Video Equipment ..........................
Connecting to a DVD Player and DTV Decoder ...
Connecting to a Computer ..................................
Controlling the Projector by a Computer .............
Setup ..................................................................
15
17
21
23
24
Using the Swivel Stand ............................................ 24
Removing the Swivel Stand ..................................... 24
Attaching the Swivel Stand ..................................... 25
Focusing and Zooming ........................................... 25
Using the Lens Shift ................................................ 25
Adjusting the Projection Distance .......................... 26
Image Projection ...................................................... 28
Basic Operation
Image Projection ............................................... 30
Basic Procedure ...................................................... 30
Selecting the On-screen Display Language ........... 31
Turning the Power off .............................................. 32
Keystone Correction ................................................ 33
Placement of the Projected Image
Using the Keystone Correction ............................ 34
Freezing a Moving Image ....................................... 35
Adjusting the Picture Aspect Ratio .......................... 35
Checking the Lamp Life Status .............................. 51
Turning on/off the On-screen Display ...................... 51
Selecting the Signal Type ....................................... 52
Setting the Video Signal (VIDEO menu only) ........... 52
Selecting a Background Image .............................. 53
Setting the Eco Mode .............................................. 53
Automatic Power Shut-off Function ........................ 54
Selecting the Menu Screen Position ........................ 54
Selecting the Menu Colour ..................................... 55
Reversing/Inverting Projected Images ............ 56
Appendix
Maintenance Indicators .................................... 58
Regarding the Lamp ......................................... 59
Lamp ...................................................................... 59
Caution Concerning the Lamp ................................ 59
Replacing the Lamp ................................................ 59
Removing and Installing the Lamp Unit ................. 60
Resetting the Lamp Timer ....................................... 61
Cleaning the Ventilative Holes .........................
Using the Kensington Lock ..............................
Troubleshooting ................................................
Connecting Pin Assignments ..........................
(RS-232C) Specifications
and Command Settings ..............................
Computer Compatibility Chart .........................
Specifications ....................................................
Dimensions ........................................................
Glossary .............................................................
Index ...................................................................
62
63
63
64
65
66
67
68
69
70
Adjustments and Settings
Using the Menu Screen .................................... 38
Menu Selections (Adjustment) ................................ 38
Menu Selections (Settings) ..................................... 40
Menu Bar Items ................................................. 42
Adjusting the Picture ........................................ 44
Adjusting Image Preferences .................................. 44
Adjusting the Colour Temperature .......................... 45
Gamma Correction Function ................................... 46
Emphasizing the Contrast ....................................... 46
Picture Setting Function ........................................... 47
Adjusting the Computer and
DVD/DTV Images ......................................... 48
When Auto Sync is OFF ........................................... 48
Special Modes Adjustment ..................................... 49
Auto Sync Adjustment ............................................. 50
Checking the Input Signal ....................................... 50
-3
XV_Z200E_E_p01_03.p65
3
03.10.30, 13:13PM
IMPORTANT SAFEGUARDS
ATTENTION: Please read all of these instructions before you operate your Projector for the first
time. Save these instructions for future reference.
For your own protection and prolonged operation of your Projector, be sure to read the following “IMPORTANT
SAFEGUARDS” carefully, before use.
This projector has been engineered and manufactured to ensure your personal safety. But IMPROPER USE
CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards
incorporated into this Projector, observe the following basic rules for its installation, use and servicing.
1. Unplug the Projector from the wall outlet before
cleaning.
2. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
3. Do not use attachments not recommended by
the Projector manufacturer, as they may cause
hazards.
4. Do not use the Projector near water; for example,
near a bathtub, washbowl, kitchen sink, laundry
tub, in a wet basement, near a swimming pool,
etc. Never spill liquid into the projector.
5. Do not place the Projector on an unstable cart,
stand, or table. The Projector may fall, which may
cause serious injury to a child or an adult, and/or
serious damage to the unit.
6. Wall or Ceiling Mounting—The product should be
mounted to a wall or ceiling only as
recommended by the manufacturer.
7. Projector equipment and
cart combinations should
be moved with care.
Quick stops, excessive
force, and uneven
surfaces may cause the
equipment and cart
combination to overturn.
8. Slots and openings in the cabinet back and
bottom are provided for ventilation. To ensure
reliable operation of the Projector and to protect
it from overheating, these openings must not be
blocked or covered. The openings should never
be covered with cloth or other material.
9. This Projector should never be placed near or
over a radiator or heating vent. The Projector
should not be placed in a built-in installation such
as a bookcase unless proper ventilation is
provided.
10. The Projector should be operated only from the
type of power source indicated on the back of
the projector or in the specifications. If you are
not sure of the type of power supplied to your
home, consult your Projector dealer or local
power company.
11. Do not place the Projector where the cord will be
abused by persons walking on it.
12. Follow all warnings and instructions marked on
the Projector.
13. To prevent damage to the projector due to
lightning and power-line surges, unplug the
projector from the power outlet, when not in use.
14. Do not overload wall outlets and extension cords
with too many products, because this can result
in fire or electric shock.
15. Never push objects of any kind into the Projector
through the cabinet slots as they may touch highvoltage points or cause a short circuit. This could
result in a fire or electric shock.
16. Do not attempt to service the Projector yourself.
Opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
17. Unplug the Projector equipment from the wall
outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power cord or plug is damaged
or frayed.
b. If liquid has been spilled into the Projector.
c. If the Projector has been exposed to rain
or water.
d. If the Projector does not operate normally
when you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions, as improper
adjustment of other controls may cause
damage and will often require extensive
work by a qualified technician to restore the
Projector to normal operation.
e. If the Projector has been dropped or the
cabinet has been damaged.
f. When the Projector exhibits a distinct
change in performance—this indicates a
need for service.
18. When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer that have the
same characteristics as the original parts.
Unauthorised substitutions may result in fire,
electric shock, or other hazards.
-4
XV_Z200E_E_p04_12.p65
4
03.10.30, 13:13PM
Introduction
19. This Projector is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type mains plug.
b. Three-wire grounding type mains plug with
a grounding terminal.
This plug will only fit into a grounding type
power outlet.
• Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.
• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• All other company or product names are trademarks or registered trademarks of their respective companies.
-5
XV_Z200E_E_p04_12.p65
5
03.10.30, 13:13PM
IMPORTANT SAFEGUARDS
Be sure to read the following safeguards when setting up
your projector.
Caution concerning the lamp unit
■ There is a potential hazard of glass
particles if the lamp ruptures. In case
of lamp rupture, contact your nearest Sharp Authorised Projector
Dealer or Service Centre for replacement.
See “Replacing the Lamp” on page 59.
CAUTION
PRECAUCIÓN
PRÉCAUTION
BQC-XVZ200++1
Cautions concerning the setup of the projector
■ For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed
in an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the lens and part of filter must be cleaned more often
than usual. As long as the projector is properly maintained in this manner, use in these environments will
not reduce the overall operation life. Please note that
all internal cleaning must be performed by a Sharp
Authorised Projector Dealer or Service Centre.
Do not set up the projector in places exposed to
direct sunlight or bright light.
■ Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes
out the colours, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a
sunny or bright room.
Do not subject the projector to hard impact and/
or vibration.
■ Take care with the lens so as not to hit or damage the
surface of the lens.
Rest your eyes occasionally.
■ Watching the screen for long hours continuously will make
your eyes tired. Be sure to occasionally rest your eyes.
Do not expose the projector to extreme heat or
cold.
■ Operating temperature:
+5°C to 35°C
■ Storage temperature:
–20°C to +60°C
+35˚C
+5˚C
Notes on Operation
■ If the cooling fan becomes obstructed, a protection
device will automatically turn off the projector lamp. This
does not indicate a malfunction. Remove the projector
power cord from the wall outlet and wait at least 10
minutes. Then turn on the power by plugging the power
cord back in. This will return the projector to the normal
operating condition.
Cautions regarding the transportation of the projector
■ When transporting the projector, be sure not to subject
it to hard impact and/or vibration, as this can result in
damage. Take extra caution with the lens. Before moving the projector, be sure to unplug the power cord from
the wall outlet, and disconnect any other cables connected to it.
Other connected equipment
■ When connecting other audio-visual equipment or a
computer to the projector, make the connections AFTER turning off the projector and the equipment to be
connected.
■ Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
Temperature monitor function
■ If the projector starts to overheat
due to setup problems or blockage
of the air vents, “
” and
“
” will blink in the lower left
corner of the picture. If the temperature continues to rise, the lamp will turn off, the
temperature warning indicator on the projector will blink,
and after a 90-second cooling-off period the projector
will enter the standby mode. Refer to “Maintenance Indicators” on page 58 for details.
Info
• The cooling fan regulates the internal temperature, and
its performance is automatically controlled. The sound
of the fan may change during projector operation due
to changes in the fan speed. This does not indicate
malfunction.
■ The exhaust ventilative
holes, the lamp unit cover
and adjacent areas may
get extremely hot during
projector operation. To prevent injury, do not touch
these areas until they have
sufficiently cooled down.
■ Allow at least 30 cm of space between the exhaust
ventilative hole and the nearest wall or obstruction.
-6
XV_Z200E_E_p04_12.p65
6
03.10.30, 13:13PM
Quick Guide
Introduction
○
In this page, connection of the projector and the video equipment is explained as an example
for the procedure from setup to projection. Refer to each page for details.
○
○
Required equipments
Video equipment
○
○
○
Power cord
○
Remote control
• Insert the batteries.
(Page 11)
○
○
Projector
○
○
○
○
Video cable
1. Place the projector facing a wall or a screen.
2. Connect to video equipment. (Page 16)
6. Turn the projector on using
control. (Page 30)
on the remote
ON button
INPUT 4 button
The power indicator
illuminates green.
7. Press
on the remote control to select the
INPUT 4 mode. (Page 31)
"On-screen Display
Video cable
To INPUT 4
terminal
8. Turn on the video equipment.
ON
To video out
put terminal
3. Connect the output terminal of the video equipment to the input terminal of the audio equipment using an audio cable.
4. Plug the power cord into the AC socket of the
projector and into the wall outlet. (Page 14)
5. Remove the lens cap from the lens.
9. Play the video.
10.Adjust the image size, image position and the
focus. (Page 25)
Adjust the zooming by
moving the zoom knob.
Adjust the height of the image
by rotating the lens shift dial.
Lens cap
Adjust the focus by
rotating the focus ring.
Note
Power cord
• This projector can also be connected to a computer
as well as to video equipment. (Page 21)
-7
XV_Z200E_E_p04_12.p65
7
03.10.30, 13:13PM
Part Names
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Projector (Front and Top View)
Lens shift dial 25
58 TEMPERATURE
WARNING indicator
Zoom knob 25
58 LAMP indicator
Exhaust ventilative hole 6
30 POWER indicator
Focus ring 25
6
Exhaust ventilative hole
Remote control sensor 11
Lens cap
Attaching the Lens Cap
The lens cap can be attached to the
projector using commercially
available straps (for cellular phones
etc.), as shown in the figure.
Projector (Side and Rear View)
ADJUSTMENT buttons 39
(ƒ/∂/ß/©)
UNDO button 39
KEYSTONE button 33
38 MENU button
32 STANDBY
button
31 INPUT button
30 ON button
PICTURE SETTING button 47
ENTER button 39
35 RESIZE button
24 Swivel Stand
LOCK/UNLOCK lever
-8
XV_Z200E_E_p04_12.p65
8
03.10.30, 13:13PM
Projector (Rear View)
Introduction
Remote control sensor 11
62 Intake ventilative hole
Intake ventilative hole 62
INPUT 2/DIGITAL INPUT 18
terminal
INPUT 3 S-VIDEO terminal 15
(4-pin Mini DIN)
23 RS-232C terminal
(9-pin D-sub)
14 AC socket
INPUT 1 COMPONENT 17
terminals (RCA)
INPUT 4 VIDEO terminal (RCA) 16
20 DIGITAL INPUT
TYPE switch
Using the Terminal Cover
When the projector is used on a desktop, high mounted or ceiling mounted, attach the terminal cover (supplied)
to hide the connecting cables.
Attaching the Terminal
Cover
1 Align with the tabs on
the projector and
then press the
terminal cover in the
direction of the arrow.
2 Tighten the two
screws on the bottom
of the projector.
1
2 Tighten the screws
Removing the Terminal
Cover
1 Loosen the two screws
on the bottom of the
projector.
2 Raise the terminal cover
and pull it out in the
direction of the arrow.
2
1 Loosen the screws
-9
XV_Z200E_E_p04_12.p65
9
03.10.30, 13:13PM
Part Names
Remote Control (Front View)
STANDBY button 32
30 ON button
KEYSTONE button 33
ENTER button 39
38 MENU button
39 ADJUSTMENT buttons
(ƒ/∂/ß/©)
UNDO button 39
INPUT 1 button 31
INPUT 2 button 31
INPUT 4 button 31
AUTO SYNC button 50
RGB/COMP. button 52
31 INPUT 3 button
31 DIGITAL INPUT button
35 RESIZE button
47 PICTURE SETTING button
35 FREEZE button
Remote Control (Top View)
Remote control signal transmitters
-10
XV_Z200E_E_p04_12.p65
10
03.10.30, 13:13PM
Operating the Remote Control
Introduction
Available Range of the Remote Control
Remote control
■ The remote control can be used to control the projector
within the ranges shown in the illustration.
7m
Note
45˚
30˚
30˚
• The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal
may differ due to the screen material.
45˚
When using the remote control:
• Be sure not to drop, or expose to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp.
Under that circumstance, move the projector away from the fluorescent lamp.
30˚
Remote control
Inserting the Batteries
The batteries (two “AA” size) are included in
the package.
1
Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
2
Insert the included batteries.
3
Insert the lower tab of the
cover into the opening, and
lower the cover until it clicks
in place.
• Insert the batteries making sure the
and
polarities correctly match the
marks inside the battery compartment.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Insert the batteries making sure the polarities correctly match the
and
marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak.
Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove
them using a cloth.
• The batteries included with this projector may exhaust over a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries when they have run out.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
-11
XV_Z200E_E_p04_12.p65
11
03.10.30, 13:13PM
Accessories
Supplied accessories
Power cord
(For Europe except U.K.)
Remote control
Two AA size batteries
(For U.K., Hong Kong
and Singapore)
(For Australia
and New Zealand)
Note
• Depending on the region, projectors are shipped with only
one power cord (see above). Use the power cord that corresponds to the wall outlet in your country.
21 pin RCA
conversion adaptor
Terminal cover
Video cable
(Supplied for Europe only)
Screws for terminal cover
Lens cap
Projector Operation manual
Optional accessories
3 RCA to 15-pin D-sub cable (3.0 m)
DVI to 15-pin D-sub adaptor (20 cm)
DVI cable (3.0 m)
AN-C3CP
AN-A1DV
AN-C3DV
Note
• Some of the cables may not be available depending on the region. Please check with your nearest Sharp
Authorised Projector Dealer or Service Centre for replacement.
-12
XV_Z200E_E_p04_12.p65
12
03.10.30, 13:13PM
Connections and Setup
Connections and Setup
XV_Z200E_E_p13_24.p65
13
03.10.30, 13:13PM
Connecting the Projector to Other Devices
Before Connecting
Note
• Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off
the devices to be connected. After making all connections, turn on the projector and then the other
devices.
When connecting a computer, be sure that it is the last device to be turned on after all the connections are made.
• Be sure to read the operation manuals of the devices to be connected before making connections.
This projector can be connected to:
Video equipment:
■ A VCR, DVD player or other video equipment (See page 15.)
■ A DVD player or DTV* decoder (See page 17.)
*DTV is the umbrella term used to describe the new digital television system in the United States.
A computer using:
■ DVI to 15-Pin D-sub adapter (See page 21.)
■ A DVI cable (See page 22.)
■ An RS-232C cable (See page 23.)
Connecting the Power
Cord
Supplied
accessory
Plug in the supplied power cord into
the AC socket on the rear of the projector.
Power cord
-14
XV_Z200E_E_p13_24.p65
14
03.10.30, 13:13PM
Connecting to Video Equipment
Connecting to Video
Equipment Using an
S-video Cable (INPUT 3)
1
Connect an S-video cable to
the projector.
2
Connect the S-video cable to
the video equipment.
Connections and Setup
Using an S-video cable, a VCR, DVD player or
other video equipment can be connected to
INPUT 3 input terminal.
S-video cable
(commercially available)
To INPUT 3 terminal
Note
• The INPUT 3 (S-VIDEO) terminal uses a
video signal system in which the picture
is separated into color and luminance signals to realize a higher-quality image. To
view a higher-quality image, use a commercially available S-video cable to connect the INPUT 3 terminal on the projector and the S-video output terminal on the
video equipment.
To S-video output terminal
VCR or other video equipment
-15
XV_Z200E_E_p13_24.p65
15
03.10.30, 13:13PM
Connecting the Projector to Other Devices
Connecting to Video
Equipment Using a
Composite Video Cable
(INPUT 4)
Using a composite video cable, a VCR, DVD
player or other video equipment can be connected to INPUT 4 input terminal.
1
Connect a composite video
cable to the projector.
To INPUT 4 terminal
2
Connect the composite video
cable to the video equipment.
Composite video cable
To video output terminal
VCR or other video equipment
-16
XV_Z200E_E_p13_24.p65
16
03.10.30, 13:13PM
Connecting to a DVD Player and DTV Decoder
Connections and Setup
Connecting to
Component Video
Equipment Using a
Component Cable
(INPUT 1)
Use a component cable when connecting component video equipment such as DVD players
and DTV decoders to INPUT 1 terminals.
1
Connect a component cable to
the projector.
2
Connect the above cable to the
component video equipment.
Note
• Make sure to turn both the projector and
the video equipment off before connecting.
To INPUT 1 terminals
Component cable
(commercially available)
To analog component
output terminal
DVD player or
DTV decoder
-17
XV_Z200E_E_p13_24.p65
17
03.10.30, 13:13PM
Connecting the Projector to Other Devices
Connecting to Component Video Equipment
Using a 3 RCA to 15-pin
D-sub Cable and the
DVI to 15-pin D-sub
Adaptor (INPUT 2)
3 RCA to 15-pin
D-sub cable
Type: AN-C3CP
(3.0 m)
Optional
accessories
DVI to 15-pin
D-sub adaptor
Type: AN-A1DV
(20 cm)
Use a 3 RCA to 15-pin D-sub cable and the
DVI to 15-pin D-sub adaptor when connecting
component video equipment such as DVD
players and DTV decoders to INPUT 2 terminal.
1
Connect a DVI to 15-pin D-sub
adaptor to the projector.
2
Connect a 3 RCA to 15-pin Dsub cable to the above adaptor.
To INPUT 2 terminal
• Secure the connectors by tightening the
thumbscrews.
3
DVI to 15-pin
D-sub adaptor
(sold separately)
Connect the above cable to the
video equipment.
Note
• When connecting this projector to component output terminal of the DTV decoder, select “Component” for “Signal
on
Type” on the OSD menu or press
the remote control. (See page 52.)
• Make sure to turn both the projector and
the video equipment off before connecting.
3 RCA to 15-pin
D-sub cable
(sold separately)
To analog component
output terminal
DVD player or
DTV decoder
-18
XV_Z200E_E_p13_24.p65
18
03.10.30, 13:13PM
Connecting to RGB
Video Equipment Using
the DVI to 15-pin D-sub
Adaptor and the RGB
Cable (INPUT 2)
Optional
accessory
DVI to 15-pin D-sub adaptor
Type: AN-A1DV (20 cm)
1
Connections and Setup
Use the DVI to 15-pin D-sub adaptor and the
RGB cable when connecting RGB video equipment such as DVD players and DTV decoders
to INPUT 2 terminal.
Connect a DVI to 15-pin D-sub
adaptor to the projector.
To INPUT 2 terminal
2
Connect the above adaptor to
an RGB cable.
3
Connect the above cable to the
video equipment.
DVI to 15-pin
D-sub adaptor
(sold separately)
• Secure the connectors by tightening the
thumbscrews.
Note
• When connecting this projector to DVI output of the DTV decoder, select “RGB” for
“Signal Type” on the OSD menu or press
on the remote control. (See page 52.)
RGB cable
(commercially
available)
To RGB output terminal
DVD player or
DTV decoder
-19
XV_Z200E_E_p13_24.p65
19
03.10.30, 13:13PM
Connecting the Projector to Other Devices
Connecting to Video
Equipment with the DVI
Output Terminal Using
a DVI Cable (DIGITAL
INPUT)
DVI cable
Type: AN-C3DV
(3.0 m)
Optional
accessory
Use the DVI cable when connecting video
equipment with the DVI output terminal such
as DVD players and DTV decoders to DIGITAL
INPUT terminal.
1
Slide the “DIGITAL INPUT
TYPE” switch on the back terminal board to “VIDEO”.
2
Connect the DVI cable to the
DIGITAL INPUT terminal.
3
Connect the other end to the
corresponding terminal on the
DVD player or DTV decoder.
To DIGITAL INPUT
terminal
DIGITAL INPUT
TYPE switch
• Secure the connectors by tightening the
thumbscrews.
DVI cable
(sold separately)
Note
• Select DIGITAL INPUT mode when connecting to video equipment with the digital output terminal. (See page 31.)
• Make sure to turn both the projector and
the video equipment off before switching
the “DIGITAL INPUT TYPE” switch and
connecting.
To DVI digital output terminal
DVD player or
DTV decoder
-20
XV_Z200E_E_p13_24.p65
20
03.10.30, 13:13PM
Connecting to a Computer
Connecting to a Computer
Using the DVI to 15-pin
D-sub Adaptor and the
RGB Cable (INPUT 2)
Connect a DVI to 15-pin D-sub
adaptor to the projector.
2
Connect the above adaptor to
an RGB cable.
3
Connect the above cable to the
computer.
DVI to 15-pin D-sub adaptor
Type: AN-A1DV (20 cm)
Connections and Setup
1
Optional
accessory
To INPUT 2 terminal
• Secure the connectors by tightening the
thumbscrews.
DVI to 15-pin D-sub adaptor
(sold separately)
Note
• Refer to “Computer Compatibility Chart” on
page 66 for a list of computer signals
compatible with the projector. Use with
computer signals other than those listed may
cause some of the functions not to work.
• When connecting the projector to a computer
in this way, select “RGB” for “Signal Type” on
on the remote
the OSD menu or press
control. (See page 52.)
• A Macintosh adaptor may be required for use
with some Macintosh computers. Contact your
nearest Sharp Authorised Projector Dealer or
Service Centre.
• Depending on the computer you are using, an
image may not be projected unless the signal
output setting of the computer is switched to
the external output. Refer to the computer operation manual for switching the computer signal output settings.
RGB cable
(commercially available)
To RGB output terminal
Notebook computer
Connecting the thumbscrew cables
■ Connect the thumbscrew cable making sure that it fits correctly into the terminal. Then, firmly secure the connectors by tightening the screws on both sides of the plug.
■ Do not remove the ferrite core attached to the RGB cable.
Ferrite core
-21
XV_Z200E_E_p13_24.p65
21
03.10.30, 13:13PM
Connecting the Projector to Other Devices
Connecting to a computer with DIGITAL
RGB output Terminal
(DIGITAL INPUT)
1
Slide the “DIGITAL INPUT
TYPE” switch on the back terminal board to “PC”.
2
Connect a DVI cable to the projector.
3
Connect the above cable to the
computer.
DVI cable
Type: AN-C3DV
(3.0 m)
Optional
accessory
To DIGITAL INPUT
terminal
DIGITAL INPUT
TYPE switch
• Secure the connectors by tightening the
thumbscrews.
Note
• Select DIGITAL INPUT mode when connecting to digital output terminal of the
computer. (See page 31.)
• Before switching the “DIGITAL INPUT
TYPE” switch and connecting, be sure to
unplug the power cord of the projector
from the AC outlet and turn off the computer to be connected. After making all
connections, turn on the projector and
then the computer.
• Be sure that the computer is the last device to be turned on after all the connections are made.
DVI cable
(sold separately)
To DVI digital output terminal
Desktop computer
“Plug and Play” function
■ This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
■ Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.
Note
• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA
DDC compatible computer.
-22
XV_Z200E_E_p13_24.p65
22
03.10.30, 13:13PM
Controlling the Projector by a Computer
Controlling the
Projector Using an
RS-232C Cable
1
Connect an RS-232C cable to
the projector.
2
Connect the above cable to the
computer.
Connections and Setup
When the RS-232C terminal on the projector
is connected to a computer with an RS-232C
cable (null modem, cross type, commercially
available), the computer can be used to control the projector and check the status of the
projector. See page 65 for details.
To RS-232C terminal
RS-232C cable
(commercially available)
Note
• Do not connect or disconnect an RS-232C
cable to or from the computer while it is
on. This may damage your computer.
• The RS-232C function may not operate if
your computer terminal is not correctly set
up. Refer to the operation manual of the
computer for details.
• Refer to “Computer Compatibility Chart”
on page 66 for a list of computer signals
compatible with the projector. Use with
computer signals other than those listed
may cause some of the functions not to
work.
To RS-232C terminal
Desktop computer
-23
XV_Z200E_E_p13_24.p65
23
03.10.30, 13:13PM
Setup
Using the Swivel Stand
You can adjust the angle and direction of the
projected image by using the Swivel Stand.
1
Unlock the lever on the Swivel
Stand.
2
Adjust the angle and direction
of the projected image as you
want by lifting up the projector and rotating the projector
on the Swivel Stand.
1
Swivel Stand
LOCK/UNLOCK
lever
2
Adjustable up to
±10° from the
standard position.
Caution
• Do not hold the lens when lifting, lowering or rotating the projector.
• When lowering the projector, be careful not
to get your fingers caught in the area between the Swivel Stand and the projector.
Adjustable up to
±25° from the
standard position.
Note
• When the height or direction of the projector is adjusted, the image may become
distorted (keystoned), depending on the
relative positions of the projector and the
screen. See page 33 for details on the
keystone correction.
3
Lock the lever on the Swivel
Stand.
Removing the Swivel
Stand
1
Lift the projector (2) with
pressing the removing-stand
button on the back of the projector (1).
Adjustable up to
±3° from the
standard position.
3
2
1
Removingstand button
-24
XV_Z200E_E_p13_24.p65
24
03.10.30, 13:13PM
Attaching the Swivel
Stand
1
2
1
While holding down the button
(2), place the projector onto
the Swivel Stand (3) to attach.
3
2
Press the projector down
firmly to attach it to the Swivel
Stand to make sure it is securely attached to the Swivel
Stand.
Connections and Setup
3
Align the tabs on the front bottom of the projector (1).
Zoom knob
Focusing and Zooming
The picture can be focused and zoomed in or
out by using the Focus ring and the Zoom
knob.
Focus ring
Lens shift dial
1
Rotate the Focus ring until the
image on the screen comes
into focus.
2
Slide the Zoom knob. The image can be adjusted to the desired size within the zoom
range.
Projected Image
UP
Using the Lens Shift
The picture can be adjusted within the shift
range of the lens by rotating the lens shift dial
on the top of the projector using your finger.
DOWN
-25
XV_Z200E_E_p25_28.p65
25
03.10.30, 13:13PM
Setup
Adjusting the Projection Distance
• Refer to pages 33 and 34 about the function of Keystone correction and placement of projector using the
correction.
• Decide the placement of the projector referring to the figures on the table and the diagram below
according to the size of your screen and input signal.
Centre of the screen
(a) Maximum projection distance
(b) Minimum projection distance
(c) Horizontal placement range when projection distance is maximum.
(d) Horizontal placement range when projection distance is minimum.
(e) Vertical placement range when projection distance is maximum.
( f ) Vertical placement range when projection distance is minimum.
Placement range
(e)
(d)
(f)
(c)
±10°
Note
(b)
• The aspect ratio of the projected image shifts slightly when
the lens shift is at a position other than the top position.
• The aspect ratio of the projected image also shifts slightly
when the “H Keystone” and “V Keystone” functions are
adjusted simultaneously.
• When adjusting “H Keystone” and “V Keystone” at the same
time, the values of adjustable angles for each setting
become smaller.
• Keystone correction cannot be applied to On-screen
Display.
• When Keystone correction is applied, the resolution of image
can be deteriorated to some extent.
• There are errors of ± 3% in the formulas below.
(a)
When using a wide
screen (16:9)
In case of displaying
the 16:9 picture on the
whole of the 16:9
screen.
16
9
: Picture area
Projection distance and Keystone correction
Screen size
(16:9)(x)
Diag.
Maximum projection distance
Projection
distance (a)
Composite, S-video
480I/P, 1080I
720P
RGB
Vertical
placement range
(e)
3.2m (10'6'')
3.6m (11'10'')
4
3
Projection
distance (b)
Horizontal Placement range (d)
Composite, S-video
480I/P, 1080I
RGB
Vertical
placement range
(f)
10.5m (34' 6'')
2.6m (8' 6'')
1.8m (5' 11'')
8.7m (28' 7'') 2.3m (7' 7'')
2.5m (8' 2'')
1.8m (5' 11'') 1.5m (4' 11'')
150" (381cm)
7.9m (25'10'') 2.4m (7' 10'')
2.7m (8' 10'') 2.0m (6' 7'')
1.3m (4' 3'')
6.5m (21' 5'') 1.7m (5' 7'')
1.9m (6' 3'')
1.3m (4' 3'')
133" (338cm)
7.0m (22'11'') 2.1m (6' 11'')
2.4m (7' 10'') 1.7m (5' 7'')
1.2m (3' 11'')
5.8m (18' 12'') 1.5m (4' 11'')
1.7m (5' 7'')
1.2m (3' 11'') 1.0m (3' 3'')
106" (269cm)
5.6m (18' 3'') 1.7m (5' 7'')
1.9m (6' 3'')
1.4m (4' 7'')
0.9m (2' 11'')
4.6m (15' 1'') 1.2m (3' 11'')
1.3m (4' 3'')
0.9m (2' 11'') 0.8m (2' 7'')
100" (254cm)
5.2m (17' 2'')
1.8m (5' 11'') 1.3m (4' 3'')
0.9m (2' 11'')
4.3m (14' 3'') 1.1m (3' 7'')
1.2m (3' 11'')
0.9m (2' 11'') 0.7m (2' 4'')
92"
(234cm)
4.8m (15'10'') 1.4m (4' 7'')
1.6m (5' 3'' )
1.2m (3' 11'') 0.8m (2' 7'')
4.0m (13' 1'') 1.0m (3' 3'')
1.1m (3' 7'')
0.8m (2' 7'')
0.7m (2' 4'')
84"
(213cm)
4.4m (14' 5'')
1.3m (4' 3'')
1.5m (4' 11'') 1.1m (3' 7'')
3.6m (11' 11'') 0.9m (2' 11'')
1.0m (3' 3'')
0.7m (2' 4'')
0.6m (1' 12'')
72"
(183cm)
3.8m (12' 4'')
1.1m (3' 7'')
1.3m (4' 3'')
0.9m (2' 11'') 0.6m (1' 12'')
3.1m (10' 3'') 0.8m (2' 7'')
0.9m (2' 11'')
0.6m (1' 12'') 0.5m (1' 8'')
60"
(152cm)
3.1m (10' 3'')
0.9m (2' 11'')
1.0m (3' 3'')
0.7m (2' 4'')
0.5m (1' 8'')
2.6m (8' 6'') 0.7m (2' 4'')
0.7m (2' 4'')
0.5m (1' 8'')
40"
(102cm)
2.1m ( 6' 10'') 0.6m (1' 12'')
0.7m (2' 4'')
0.5m (1' 8'')
0.3m (' 12'')
1.7m (5' 7'') 0.4m (1' 4'')
0.4m (1' 4'')
0.3m (1' 12'') 0.2m ('
1.6m (5' 3'' )
Diag.
0.7m (2' 4'')
1.1m (3' 7'')
0.4m (1' 4'')
8'')
x: Screen size (diag.) (in)
Projection distance and Keystone correction
Screen size
(4:3)(x)
Minimum projection distance
Maximum projection distance
Projection
distance (a)
Horizontal Placement range (c)
Composite, S-video
480I/P, 1080I
720P
RGB
Vertical
placement range
(e)
Projection
distance (b)
Horizontal Placement range (d)
Composite, S-video
480I/P, 1080I
720P
RGB
Vertical
placement range
(f)
200" (508cm)
–
–
–
–
–
8.0m (26' 3'')
2.1m (6' 11'')
2.3m (7' 7'')
1.6m (5' 3'')
1.4m (4' 7'')
150" (381cm)
7.2m (23' 9'')
2.2m (7' 3'')
2.5m (8' 2'')
1.8m (5' 11'')
1.2m (3' 11'')
6.0m (19' 8'')
1.6m (5' 3'')
1.7m (5' 7'')
1.2m (3' 11'')
1.0m (3' 3'')
100" (254cm)
4.8m (15' 9'')
1.4m (4' 7'')
1.6m (5' 3'' )
1.2m (3' 11'')
0.8m (2' 7'')
4.0m (13' 1'')
1.0m (3' 3'')
1.1m (3' 7'')
0.8m (2' 7'')
0.7m (2' 4'')
84"
(213cm)
4.0m (13' 3'')
1.2m (3' 11'')
1.4m (4' 7'')
1.0m (3' 3'')
0.7m (2' 4'')
3.3m (10' 11'') 0.9m (2' 11'')
0.9m (2' 11'')
0.6m (1' 12'')
0.5m (1' 8'')
72"
(183cm)
3.5m (11' 4'')
1.0m (3' 3'')
1.2m (3' 11'')
0.8m (2' 7'')
0.6m (1' 12'')
2.9m (9' 4'')
0.7m (2' 4'')
0.8m (2' 7'')
0.5m (1' 8'')
0.5m (1' 8'')
60"
(152cm)
2.9m (9' 5'')
0.8m (2' 7'')
0.9m (2' 11'')
0.7m (2' 4'')
0.5m (1' 8'')
2.4m (7' 9'')
0.6m (1' 12'')
0.6m (1' 12'')
0.4m (1' 4'')
0.4m (1' 4'')
40"
(102cm)
1.9m (6' 3'')
0.5m (1' 8'')
0.4m (1' 4'')
0.4m (1' 4'')
0.3m (' 12'')
1.6m (5' 2'')
0.4m (1' 4'')
0.4m (1' 4'')
0.3m (1' 12'')
0.2m (1' 8'')
(a) = (0.04849498x - 0.038639669)
(b) =(0.040201488x - 0.038804856)
x: Screen size (diag.) (in)
: Screen area
: Picture area
-26
XV_Z200E_E_p25_28.p65
720P
200" (508cm)
(a) = (0.052833802x - 0.038639669)
(b) =(0.043798292 x - 0.038804856)
When using a normal
screen (4:3)
In case of setting the
16:9 picture to the full
horizontal width of the
4:3 screen.
Minimum projection distance
Horizontal Placement range (c)
26
03.10.30, 13:13PM
Upper and Lower Lens Shift Position
• This projector is equipped with a lens shift function that lets you adjust the projection height.
• Adjust the projection height to match the setup configuration.
• The screen can be moved maximum the length of one screen vertically using the lens shift.
Note
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level.
Tilting or angling the projector will reduce the effectiveness of the lens shift function.
Screen size: 254 cm
Aspect ratio: 16:9
Connections and Setup
Screen
Lens centre
Lower lens shift position
(High mount setup)
90°
Lens centre
90°
Lower edge of screen (White portion) =
Standard (0) point
Upper lens shift position
(Desktop setup)
Upper and Lower Lens Shift Position (Ceiling Mount)
When the projector is in the inverted position, use the upper edge of the screen as the base line,
and exchange the lower and upper lens shift values.
Screen size: 254 cm
Aspect ratio: 16:9
Screen
90°
90°
-27
XV_Z200E_E_p25_28.p65
27
03.10.30, 13:13PM
Setup
Image Projection
Rear Projection
■ Place a translucent screen between the projector and the audience.
■ Use the projector’s menu screen to reverse the projected image. (See page 56
for use of this function.)
When using the default setting.
▼On-screen Display
Note
• Optimal image quality can be achieved when the projector is
positioned perpendicular to the screen with all feet flat and leveled.
The image is reversed.
Projection using a mirror
■ Place a mirror (normal flat type) in front of the lens.
Info
• When using a mirror, be sure to carefully position both the
projector and the mirror so the light does not shine into the
eyes of the audience.
Ceiling-mount setup
■ It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation.
■ Before mounting the
projector, remove the
Swivel Stand. (See pages
24 and 25 for removing and
attaching the Swivel Stand.)
■ Before mounting the
projector, contact your
nearest Sharp Authorised
Projector Dealer or Service
Centre to obtain the recommended ceiling-mount bracket (sold
separately). (AN-TK202 ceiling-mount bracket, AN-TK201
extension tube, AN-60KT ceiling adaptors for AN-TK202 or ANTK201)
■ When the projector is in the inverted position, use the upper
edge of the screen as the base line.
■ Use the projector’s menu screen to select the appropriate projection mode. (See page 56 for use of this function.)
When using the default setting.
▼On-screen Display
The image is inverted.
-28
XV_Z200E_E_p25_28.p65
28
03.10.30, 13:13PM
Basic Operation
Basic Operation
XV_Z200E_E_p29_43.p65
29
03.10.30, 13:14PM
Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
LAMP indicator
TEMP.
LAMP
POWER
Info
• The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language according to the procedure on page 31.
1
2
POWER indicator
Plug the power cord into the
wall outlet.
ON button
• The POWER indicator illuminates red,
and the projector enters standby mode.
INPUT button
Press
or
on the remote control
on the projector.
• The blinking green LAMP indicator
shows that the lamp is warming up.
Wait until the indicator stops blinking
before operating the projector.
• If the power is turned off and then immediately turned on again, it may take
a short while before the lamp turns on.
Note
• After the projector is unpacked and
turned on for the first time, a slight
odour may be emitted from the exhaust ventilative holes. This odor will
soon disappear with use.
ON button
When the power is on, the LAMP indicator illuminates, indicating the status of the lamp.
Green: Lamp is ready.
Green blinking: Warming up. / Cooling
down.
Red: Change the lamp.
INPUT buttons
-30
XV_Z200E_E_p29_43.p65
30
03.10.30, 13:14PM
3
"On-screen Display (Example)
Press
,
,
,
or
on the remote control or
on
the projector to select the INPUT mode.
INPUT 1 Mode
• After pressing
once on the projector,
use
to select the desired input mode.
INPUT 2 Mode
Note
• When no signal is received, “NO SIGNAL” will be displayed. When a signal that the projector is not preset to
receive is received, “NOT REG.” will
be displayed.
Selecting the Onscreen Display Language
INPUT 4 Mode
Basic Operation
About the INPUT modes
INPUT 1 Used for projecting im(Compo- ages from equipment
connected to INPUT 1
nent)
terminals.
INPUT 2 Used for projecting im(Compoages from equipment
nent/RGB) connected to INPUT 2
terminal.
INPUT 3 Used for projecting im(S-Video) ages from equipment
connected to INPUT 3
terminal.
INPUT 4 Used for projecting images from equipment
(Video)
connected to INPUT 4
terminal.
DIGITAL Used for projecting
images from equipment
connected to DIGITAL
INPUT terminal.
INPUT 3 Mode
DIGITAL INPUT Mode
On-screen Display
English is the preset language for the Onscreen Display; however, this can be changed
to German, Spanish, Dutch, French, Italian,
Swedish, Portuguese, Chinese, Korean or
Japanese.
Display the “Language” menu and select the desired Language.
➝For operating the menu screen, see
pages 38 to 41.
-31
XV_Z200E_E_p29_43.p65
31
03.10.30, 13:14PM
Image Projection
STANDBY button
Turning the Power off
1
Press
on the remote con-
trol or
on the projector,
or
again
then press
while the confirmation message
is displayed, to put the projector into the standby mode.
• A dimly-lit screen is displayed for a
short time to reduce lamp damage.
Note
• If you accidentally pressed
and do not want to put the projector
into the standby mode, wait until the
confirmation message disappears.
2
STANDBY button
Unplug the power cord from the
AC outlet after the cooling fan
stops.
Info
• Do not unplug the power cord during projection or cooling fan operation. This can cause damage due
to the rise in internal temperature,
as the cooling fan also stops.
• When connected to equipment such
as an amplifier, be sure to turn off
the power to the equipment connected first and then to the projector.
-32
XV_Z200E_E_p29_43.p65
32
03.10.30, 13:14PM
KEYSTONE button
Keystone Correction
This function can be used to adjust the Keystone settings.
Note
• For details about using the menu screen,
see pages 38 to 41.
1
Press
on the projector or
on the remote control.
2
Press / to select “H Keystone” or “V Keystone”.
Selected Item
H Keystone
V Keystone
Reset
Description
Horizontally adjusts the keystone settings.
Vertically adjusts the keystone settings.
V and H Keystone adjustments are
returned to the factory preset settings.
KEYSTONE button
", ',\, |
buttons
Press / to move the mark
on the selected adjustment
item to the desired setting.
Basic Operation
3
", ',\, |
buttons
Note
• Straight lines and the edges of the
displayed image may appear
jagged, when adjusting the Keystone setting.
• When adjusting “H Keystone” and
“V Keystone” at the same time, the
values of adjustable angles for each
setting become smaller.
• The adjustable value of the “V Keystone” becomes extremely small
when “H Keystone” is made to be
the maximum value.
• Keystone correction is disabled
while the picture mode is set to
“SMART STRETCH”. (See page
35.)
4
To return to the normal screen,
again.
press
Horizontal Keystone Correction
Vertical Keystone Correction
-33
XV_Z200E_E_p29_43.p65
33
03.10.30, 13:14PM
Image Projection
Placement of the Projected Image Using the
Keystone Correction
Place the projector at a distance from the
screen that allows images to be projected onto
the screen by referring to “Adjusting the Projection Distance” on pages 26 and 27.
1
Project the test pattern of the
Keystone correction function
onto the screen. Rotate the Focus ring until the image on the
screen comes into focus. (See
page 25.)
2
Change the projection angle
using the Swivel Stand to properly project images onto the
screen. (See page 24).
3
Align the edge of the screen
closest to the projector with
the test pattern by adjusting
the zoom and the Swivel Stand.
(See pages 24 and 25.)
4
Adjust the Keystone function
so that the size of the projected
image matches the screen
size. (See page 33.)
5
Align the image on the screen
by adjusting the zoom function
and the Swivel Stand.
6
Adjust the focus so that the
projected image is in focus at
the centre of the screen. (See
page 25.)
: Screen area
Note
• The aspect ratio of the projected image
shifts slightly when the lens shift is at a
position other than the top position.
• The aspect ratio of the projected image
also shifts slightly when the “H Keystone”
and “V Keystone” functions are adjusted
simultaneously.
-34
XV_Z200E_E_p29_43.p65
34
03.10.30, 13:14PM
Freezing a Moving
Image
You can instantly freeze a moving image with
the remote control.
1
Press
.
• The projected image is frozen.
2
FREEZE button
Press
again to return to the
moving image from the currently connected device.
Adjusting the Picture
Aspect Ratio
RESIZE button
Basic Operation
This function allows you to modify or customize the picture display mode to enhance the
input image. Depending on the input signal,
you can choose SIDE BAR, SMART STRETCH,
CINEMA ZOOM or STRETCH image.
Press
. Each time
is pressed,
the picture mode changes as
shown on the next page.
RESIZE button
-35
XV_Z200E_E_p29_43.p65
35
03.10.30, 13:14PM
Image Projection
SIDE BAR
SMART
STRETCH
CINEMA
ZOOM
STRETCH
768 ⳯ 576
1024 ⳯ 576
1024 ⳯ 576
1024 ⳯ 576
480P
768 ⳯ 576
1024 ⳯ 576
1024 ⳯ 576
1024 ⳯ 576
720P
–
–
–
1024 ⳯ 576
1080I
–
–
–
1024 ⳯ 576
480I
480P
576I
576P
NTSC
PAL
SECAM
For 4:3
aspect ratio
For 16:9
aspect ratio
VGA
SVGA
XGA
• “STRETCH” is fixed when 540P, 720P or 1080I signal is entered.
• “SMART STRETCH” cannot be selected while input signal from a computer (VGA, SVGA or XGA) is entered.
Input Signal
SIDE BAR
Output screen image
SMART STRETCH
CINEMA ZOOM
STRETCH
4:3 aspect ratio
480I
480P
576I
576P
NTSC
PAL
SECAM
Letterbox
Squeeze
540P
1080I
16:9 aspect ratio
720P
VGA
SVGA
XGA
4:3 aspect ratio
Note
• “SMART STRETCH” cannot be selected while the Keystone correction (page 33) is being adjusted.
• Keystone correction (page 33) is disabled while the picture mode is set to “SMART STRETCH”.
• 580I/580P is displayed on the screen when signal 576I/576P is input.
-36
XV_Z200E_E_p29_43.p65
36
03.10.30, 13:14PM
Adjustments and Settings
Adjustments and Settings
XV_Z200E_E_p29_43.p65
37
03.10.30, 13:14PM
Using the Menu Screen
The menu screens allow you to adjust the image and various projector settings.
The menu can be operated to achieve two functions, adjustment and setting.
(For adjusting the menu items, see pages 38 and 39. For setting the menu items, see pages
40 and 41.)
Menu screen (example)
Menu Selections
(Adjustments)
1
Press
", ', \, | buttons
MENU button
UNDO button
.
• The menu screen is displayed.
Note
• The “Picture” menu screen for the
selected input mode is displayed.
ENTER button
", ', \, | buttons
MENU button
UNDO button
ENTER button
-38
XV_Z200E_E_p29_43.p65
38
03.10.30, 13:14PM
2
Select the menu icon.
Press \ or | to display the
other menu screens.
• The menu icon for the selected menu
screen is highlighted.
Menu icon
Menu screen
Picture
Fine Sync
Options
Language
PRJ Mode
Note
• The “Fine Sync” menu is not available for INPUT 3 or 4.
• For items on the menus, see the
tree charts on pages 42 and 43.
3
Press " or ' to select the item
you want to adjust.
Select
the item.
Note
• To display a single adjustment item,
after selecting the item.
press
Only the menu bar and the selected
adjustment item will be displayed.
Then if you press " or ', the following item (“Bright” after “Contrast”) will be displayed.
to return to the previous
• Press
screen.
Adjustments and Settings
4
Press \ or | to adjust the item
selected.
• The adjustment is stored.
Adjust the item.
5
Press
.
• The menu screen will disappear.
-39
XV_Z200E_E_p29_43.p65
39
03.10.30, 13:14PM
Using the Menu Screen
Menu Selections
(Settings)
1
Press
", ', \, | buttons
UNDO button
MENU button
.
• The menu screen is displayed.
Note
• The “Picture” menu screen for the
selected input mode is displayed.
ENTER button
", ', \, | buttons
MENU button
UNDO button
ENTER button
2
Press \ or | to display the
other menu screens.
Select the menu icon.
• The menu icon for the selected menu
screen is highlighted.
Menu icon
Menu screen
Picture
Fine Sync
Options
Language
PRJ Mode
Note
• The “Fine Sync” menu is not available for INPUT 3 or 4.
• For items on the menus, see the
tree charts on pages 42 and 43.
-40
XV_Z200E_E_p29_43.p65
40
03.10.30, 13:14PM
3
Press " or ' to select the
item you want to set.
Select
the item.
Note
• Press
to return to the previous
screen.
• In some menus, select the icon us”.
ing “
4
Press |.
• The sub menu is displayed.
Sub
menu
5
Press " or ' to select the setting of the item displayed in the
sub menu.
Sub
menu
Press
7
Press
.
Adjustments and Settings
6
• The item selected is set.
.
• The menu screen will disappear.
-41
XV_Z200E_E_p29_43.p65
41
03.10.30, 13:14PM
Menu Bar Items
■ INPUT 1 / 2 / DIGITAL INPUT Mode
Sub menu
Main menu
Picture (
)
Main menu
Contrast
ⳮ30
Ⳮ30
Bright
ⳮ30
Ⳮ30
Deutsch
Color
ⳮ30
Ⳮ30
Español
Tint
ⳮ30
Ⳮ30
Nederlands
Sharp
ⳮ30
Ⳮ30
Français
Red
ⳮ30
Ⳮ30
Italiano
Blue
ⳮ30
Ⳮ30
Svenska
Language (
)
English
Português
Reset
CLR Temp
Gamma
5500k
0
10
6500k
0
10
7500k
0
10
8500k
0
10
9300k
0
10
CeilingⳭFront
10500k
0
10
Rear
PRJ Mode (
)
Front
CeilingⳭRear
Standard
Cinema 1
Cinema 2
Cinema 3
White Emphasis [ON/OFF]
Picture Setting
Memory 1
Memory 2
Memory 3
Memory 4
Memory 5
Memory OFF
Fine Sync (
)
Clock
ⳮ30
Phase
ⳮ15
Ⳮ30
Ⳮ15
H-Pos
ⳮ30
Ⳮ30
V-Pos
ⳮ30
Ⳮ30
Reset
Special Modes
Auto Sync
[ON/OFF]
Signal Info
Options (
)
640⳯480
720⳯480
480P
Resolution
Hor Freq
Vert Freq
640⳯480
37.5 kHz
72 Hz
Lamp Timer (Life)
OSD Display [ON/OFF]
RGB
Signal Type
Component
Background [None/Blue]
Eco Mode [Eco/Standard]
Note
Auto Power Off [ON/OFF]
Menu Position
Center
Upper Right
Lower Right
Upper Left
Lower Left
Menu Color [Opaque/Translucent]
• The resolution, vertical frequency and horizontal
frequency figures displayed above are for
example purposes only.
• “Color”, “Tint”, and “Sharp” do not appear when
“RGB” is selected in INPUT 2 mode.
• “Signal Type” is not displayed when using
INPUT 1.
• “Color”, “Tint”, “Sharp”, “Clock”, “Phase”, “HPos”, “V-Pos”, “Special Modes” and “Auto Sync”
cannot be used in the DIGITAL INPUT mode.
• “Clock”, “Phase” and “Auto Sync” cannot be
used in the Component mode.
-42
XV_Z200E_E_p29_43.p65
42
03.10.30, 13:14PM
■ INPUT 3 / 4 Mode
Sub menu
Main menu
Picture (
)
Main menu
Contrast
ⳮ30
Ⳮ30
Bright
ⳮ30
Ⳮ30
Deutsch
Color
ⳮ30
Ⳮ30
Español
Tint
ⳮ30
Ⳮ30
Nederlands
Sharp
ⳮ30
Ⳮ30
Français
Red
ⳮ30
Ⳮ30
Italiano
Blue
ⳮ30
Ⳮ30
Svenska
Language (
)
English
Português
Reset
CLR Temp
Gamma
5500K
0
10
6500K
3D
Progressive
0
10
7500K
3D Progressive
0
10
8500K
3D Progressive
0
10
9300K
3D Progressive
0
10
CeilingⳭFront
10500K
3D Progressive
0
10
Rear
PRJ Mode (
)
Front
CeilingⳭRear
Standard
3D Progressive
Cinema
1
3D Progressive
Cinema
2
3D Progressive
Cinema
3
3D Progressive
White Emphasis [ON/OFF]
Picture Setting
3D
Progressive
Memory
1
3D Progressive
Memory
2
3D Progressive
Memory
3
3D Progressive
Memory
4
3D Progressive
Memory
5
3D ProgrOFFessive
Memory
OFF
Options (
)
Lamp Timer (Life)
OSD Display [ON/OFF]
Video System
Auto
PAL
Adjustments and Settings
NTSC3.58
SECAM
NTSC4.43
PAL–M
PAL–N
PAL–60
Background [None/Blue]
Eco Mode [Eco/Standard]
Auto Power Off [ON/OFF]
Menu Position
Center
Upper Right
Lower Right
Upper Left
Lower Left
Menu Color [Opaque/Translucent]
Note
• “Tint” cannot be used with PAL, SECAM, PAL-M,
PAL-N or PAL-60.
-43
XV_Z200E_E_p29_43.p65
43
03.10.30, 13:14PM
Adjusting the Picture
You can adjust the projector’s picture to your preferences with the following picture settings.
Adjusting Image Preferences
On-screen Display
Note
• First select “Memory 1-5” or “Memory
OFF” when you want to save the “Picture”
menu settings. See page 47 for details.
Adjust the “Picture” menu on the menu
screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Description
\ button
| button
Contrast
For adjusting the contrast level
For less contrast
For more contrast
Bright
For adjusting the brightness of an image
For less brightness
For more brightness
Color
For adjusting the colour intensity of an image
For less colour intensity
For more colour intensity
Tint
For adjusting the tones of an image
Skin tones become purplish
Skin tones become greenish
Sharp
For making sharper or softer the contour of an image
For less sharpness
For more sharpness
Red
For adjusting the redness of an image
For weaker red
For stronger red
Blue
For adjusting the blueness of an image
For weaker blue
For stronger blue
Note
• “Color”, “Tint” and “Sharp” do not appear
for RGB input in INPUT 2 mode.
• To reset all adjustment items, select “Reset” on the “Picture” menu screen and
press
.
• “Tint” cannot be used with PAL, SECAM,
PAL-M, PAL-N or PAL-60.
• “Color”, “Tint” and “Sharp” cannot be used
in the DIGITAL INPUT mode.
-44
XV_Z200E_E_p44_50.p65
44
03.10.30, 13:14PM
On-screen Display
Adjusting the Colour
Temperature
This function allows for selecting the desired
colour temperature. With the lower value selected, the projected image becomes warmer,
reddish and incandescent-like while with the
higher value, the image becomes cooler, bluish and fluorescent-like.
Select “CLR Temp” in the “Picture”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Description
5500K
The less the value is set to, the
warmer, reddish, incandescent-like
the image becomes.
6500K
7500K
8500K
9300K
10500K
The more the value is set to, the
cooler, bluish, fluorescent-like the
image becomes.
“CLR Temp” is fine adjusted by following the
procedure below.
1
Select “CLR Temp” in the “Picture” menu on the menu
screen and press .
• A single menu bar of “CLR Temp” is
displayed.
Adjustments and Settings
2
Press ' or " to fine adjust the
colour temperature.
• With the lower value selected, the projected image becomes magentatinged. With the higher value selected,
the projected image becomes greentinged.
• Pressing \ or | changes the value
of the colour temperature in the sub
menu.
Note
•Values on “CLR Temp” are only for general standard purposes.
-45
XV_Z200E_E_p44_50.p65
45
03.10.30, 13:14PM
Adjusting the Picture
Gamma Correction
Function
On-screen Display
Gamma is an image quality enhancement
function.
Four gamma settings are available to allow for
differences in the brightness of the room.
Select “Gamma” in the “Picture” menu
on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
Standard Standard picture without gamma
correction
Cinema 1 Gives greater depth to darker portions
of images.
Cinema 2 Brightness is toned down and the
image becomes more balanced.
Cinema 3 Brighten the darker portions of images
for easier viewing in a dimly lit room.
Emphasizing the
Contrast
On-screen Display
This function emphasizes the bright portions
of images to obtain a higher contrast image.
Select “White Emphasis” in the “Picture” menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
(ON)
For emphasizing the bright portions of
images
(OFF) For disabling “White Emphasis”
-46
XV_Z200E_E_p44_50.p65
46
03.10.30, 13:14PM
On-screen Display
Picture Setting
Function
This function stores all items set in “Picture”.
Five settings can be stored separately in
“Memory 1” to “Memory 5”. Each stored setting is reassigned to each input mode (INPUT
1 to INPUT 4 and DIGITAL).
Even when the input mode or signal is
changed, you can easily select optimal settings from the stored settings.
■ Storing the Adjustment Values
for Each Memory Number
Select “Picture Setting” on the “Picture”
menu and the memory location where
you want to store the settings. Then
adjust the setting items on the “Picture”
menu.
➝For operating the menu screen, see
pages 38 to 41.
Description
Memory
1-5
Settings of all items in “Picture” can be
stored for the respective input modes.
The stored settings can be selected in
any input modes.
Besides “Memory 1” to “Memory 5”,
other settings on the “Picture” menu
can be stored for each input mode.
The settings stored in “Memory OFF”
cannot be applied when another input
mode is selected.
Memory
OFF
PICTURE SETTING button
Adjustments and Settings
Selected Item
■ Applying the Stored Settings
If you want to apply the stored settings
on the “Picture” menu, select “Picture
Setting” on the “Picture” menu and the
memory location where you have
stored the settings.
Note
• This function can be operated using the
on the projector or
on the remote
control, as well as the OSD menu screen.
Each time
or
is pressed, the
memory number changes as shown below.
Memory 1
Memory 2
Memory 3
Memory OFF
Memory 5
Memory 4
PICTURE SETTING
button
-47
XV_Z200E_E_p44_50.p65
47
03.10.30, 13:14PM
Adjusting the Computer and DVD/DTV Images
Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in
portions of the screen.
When Auto Sync is OFF
On-screen Display
When “Auto Sync” is “OFF”, interference such
as flickering or vertical stripes may occur if
displaying tilings or vertical stripes. Should
this occur, adjust “Clock”, “Phase”, “H-Pos”
and “V-Pos” for obtaining an optimum image.
Select “Clock”, “Phase”, “H-Pos” or “VPos” in the “Fine Sync” menu on the
menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Description
Clock
Adjusts vertical noise.
Phase
Adjusts horizontal noise (similar to tracking on your VCR).
H-Pos
Centres the on-screen image by moving it to the left or right.
V-Pos
Centres the on-screen image by moving it up or down.
Note
• “Clock”, “Phase”, “H-Pos” and “V-Pos” cannot be used in the DIGITAL INPUT mode.
• “Clock” and “Phase” cannot be used in the
Component mode.
• Computer image adjustments can be
on the remade easily by pressing
mote control. See page 50 for details.
• To reset all adjustment items, select “Reset” on the “Fine Sync” menu screen and
.
press
• The adjustable area of each item may be
changed according to the input signal.
AUTO SYNC
-48
XV_Z200E_E_p44_50.p65
48
03.10.30, 13:14PM
On-screen Display
Special Modes Adjustment
Ordinarily, the type of input signal is detected
and the correct resolution mode is automatically selected. However, for some signals, the
optimal resolution mode in “Special Modes”
on the “Fine Sync” menu screen may need
to be selected to match the computer display
mode.
Set the resolution by selecting “Special
Modes” in the “Fine Sync” menu on the
menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Note
• Avoid displaying computer patterns which
repeat every other line (horizontal
stripes). (Flickering may occur, making
the image hard to see.)
• When inputting DTV 1080I signal, select
the corresponding type of signal.
• When inputting 720P signal from the
video equipment, select “720P”. When
inputting 1280 × 720 signal from the computer, select “HTPC”.
• “Special Modes” cannot be used in the
DIGITAL INPUT mode.
Adjustments and Settings
-49
XV_Z200E_E_p44_50.p65
49
03.10.30, 13:14PM
Adjusting the Computer and DVD/DTV Images
Auto Sync Adjustment
On-screen Display
Used to automatically adjust a computer image.
Select whether the image is to be synchronized automatically when switching the signal with “ON” or “OFF”.
Select “Auto Sync” in the “Fine Sync”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
Auto Sync adjustment will occur
when the projector is turned on or
(ON)
when the input signals are switched,
when connected to a computer.
Auto Sync adjustment is not
(OFF) automatically performed.
Note
• When the optimum image cannot be
achieved with Auto Sync adjustment, use
manual adjustments. (See page 48.)
• The Auto Sync adjustment may take
some time to complete, depending on the
image of the computer connected to the
projector.
• “Auto Sync” cannot be used in the DIGITAL INPUT mode.
• Auto Sync adjustment is also performed
on the remote control.
by pressing
AUTO SYNC button
AUTO SYNC
Checking the Input Signal
On-screen Display
This function allows you to check the current
input signal information.
Select “Signal Info” in the “Fine Sync”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Note
• 540P is displayed on the screen when
signal 1080I is inputted during DVI connection.
-50
XV_Z200E_E_p44_50.p65
50
03.10.30, 13:14PM
Using the “Options” Menu
Checking the Lamp Life
Status
On-screen Display
You can confirm the cumulative lamp usage
time and the remaining lamp life (percentage).
Display the “Options” menu to check
the lamp life status.
➝For operating the menu screen, see
pages 38 to 41.
Lamp usage condition
Remaining lamp life
100%
5%
Approx.
Approx.
4,000 hours 200 hours
Operated exclusively
in Eco mode ( )
Operated exclusively Approx.
Approx.
in Standard mode ( ) 3,000 hours 150 hours
Note
Turning on/off the Onscreen Display
Adjustments and Settings
• It is recommended that the lamp be
changed when the remaining lamp life
becomes 5%.
For lamp replacement, contact your nearest Sharp Authorised Projector Dealer or
Service Centre.
• The table above indicates rough estimates
in the case of using only in each mode
shown. Remaining lamp life changes within
the range of the values shown depending
on the frequency at which “Eco Mode” is
switched to “ ” (Eco mode) and “ ”
(Standard mode) (see page 53).
On-screen Display
This function allows you to turn on or off the
on-screen messages that appear during input
select.
Select “OSD Display” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
(ON) All On-screen Displays are
displayed.
(OFF) INPUT/FREEZE/AUTO SYNC/
“An invalid button has been
pressed.” are not displayed.
-51
XV_Z200E_E_p51_56.p65
51
03.10.30, 13:15PM
Using the “Options” Menu
Selecting the Signal
Type
On-screen Display
This function allows you to select the input
signal type Component or RGB for INPUT 2.
Select “Signal Type” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
RGB
Component
Description
Set when RGB signals are
received.
Set when Component signals
are received.
RGB/COMP. button
Note
• “RGB” or “Component” can be selected
with
on the remote control only in
INPUT 2.
Setting the Video Signal
(VIDEO menu only)
On-screen Display
The video input system mode is preset to
“Auto”; however, it can be changed to a specific system mode if the selected system mode
is not compatible with the connected audiovisual equipment.
Select “Video System” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Note
• When the system mode is set to “Auto”,
you may not receive a clear picture due
to signal differences. Should this occur,
switch to the video system of the source
signal.
• “Auto” cannot be set for PAL-M and PALN input signals. Select “PAL-M” or “PALN” in “Video System” menu for PAL-M and
PAL-N input signals.
-52
XV_Z200E_E_p51_56.p65
52
03.10.30, 13:15PM
Selecting a
Background Image
On-screen Display
This function allows you to select the image
displayed when no signal is being sent to the
projector.
Select “Background” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
(Blue) Blue screen
(None) Black screen
Setting the Eco Mode
On-screen Display
This function allows you to select the desired
power consumption mode.
Select “Eco Mode” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item Brightness
80%
230 W
100%
285 W
(Eco mode)
(Standard mode)
Power consumption
Lamp life
Approx.
4,000 hours
Approx.
3,000 hours
Adjustments and Settings
Note
• Although lamp life and noise are improved
when “Eco Mode” is set to “ ” (Eco
mode), brightness decreases by 20%.
• “Eco Mode” is factory preset to “ ” (Standard mode).
-53
XV_Z200E_E_p51_56.p65
53
03.10.30, 13:15PM
Using the “Options” Menu
Automatic Power Shutoff Function
On-screen Display
When no input signal is detected for more than
15 minutes, the projector will automatically enter the standby mode if set to “ ” (ON).
Select “Auto Power Off” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
Projector automatically enters the
standby mode after 15 minutes
without an input signal.
Automatic Power Shut-off disabled.
Note
• “Auto Power Off” is factory preset to “ ”.
• When the Auto Power Off function is set to
(ON)”, 5 minutes before the projector
“
enters the standby mode, the message “Enter STANDBY mode in X min.” will appear on
the screen to indicate the remaining minutes.
Selecting the Menu
Screen Position
On-screen Display
This function allows you to select the desired
position of the menu screen.
Select “Menu Position” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Center
Upper
Right
Lower
Right
Upper
Left
Lower
Left
Description
The menu is displayed on the
center of the image.
The menu is displayed on the
upper right of the image.
The menu is displayed on the
lower right of the image.
The menu is displayed on the
upper left of the image.
The menu is displayed on the
lower left of the image.
-54
XV_Z200E_E_p51_56.p65
54
03.10.30, 13:15PM
Selecting the Menu
Colour
On-screen Display
This function allows you to select the colour
of the menu screen.
Select “Menu Color” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Description
(Opaque)
The menu is displayed
opaquely.
The menu is displayed
(Translucent) translucently. The part of the
menu on the image becomes
transparent.
Adjustments and Settings
-55
XV_Z200E_E_p51_56.p65
55
03.10.30, 13:15PM
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function that allows you to reverse or
invert the projected image for various applications.
Setting the Projection
Mode
On-screen Display
Display the “PRJ Mode” menu and select the desired projection mode.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Front
Ceiling + Front
Rear
Ceiling + Rear
Description
Normal image
Inverted image
Reversed image
Reversed and inverted image
Note
• This function is used for the reversed image and ceiling-mount setups. See page 28
for these setups.
-56
XV_Z200E_E_p51_56.p65
56
03.10.30, 13:15PM
Appendix
Appendix
XV_Z200E_E_p57_66.p65
57
03.10.30, 13:15PM
Maintenance Indicators
■ The warning lights on the projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter the standby mode. After the projector has entered the standby
mode, follow the procedures given below.
About the lamp indicator
TEMP.
LAMP
POWER
TEMPERATURE LAMP
WARNING
indicator
indicator
POWER
indicator
About the temperature warning indicator
If the temperature inside the
projector increases, due to
blockage of the air vents, or the
” will
setting location, “
illuminate in the lower left corner of the picture. If
the temperature keeps on rising, the lamp will turn off
and the temperature warning indicator will blink, the
cooling fan will run for a further 90 seconds, and then
the projector will enter the standby mode. After
” appears, be sure to perform the following
“
■ The lamp life becomes 0%, when used
for approximately 4,000 hours with “Eco
mode” or when used for approximately
3,000 hours with “Standard mode” (see
page 53).
■ When the remaining lamp life becomes
5% or less, “ ” (yellow) will be displayed
on the screen. When the percentage becomes 0%, “ ” will change to “ ” (red),
the lamp will automatically turn off and
then the projector will automatically enter the standby mode. At this time, the
lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth
time without replacing the lamp, the projector will not turn on.
measures.
Maintenance indicator
Abnormal
Normal
Condition
Problem
• Blocked air intake
Temperature
warning
indicator
Lamp
indicator
Power
indicator
Red on/
Standby
Off
Green on Red on
Green blinks
when the
lamp is
Red on/
warming up. Standby
Green on/
Red on
Off
Possible Solution
• Relocate the projector to an area
with proper ventilation.
The internal
• Cooling fan break• Take the projector to your nearest
temperature is
down
Sharp Authorised Projector Dealer
abnormally high.
• Internal circuit failure or Service Centre for repair.
• Clogged air intake
Time to change
the lamp.
The lamp does
not illuminate.
The power is
not turned on.
• Carefully replace the lamp. (See
• Remaining lamp life
page 59.)
becomes 5% or less. • Take the projector to your nearest
Sharp Authorised Projector Dealer
or Service Centre for repair.
• Burnt-out lamp
• Lamp circuit failure • Please exercise care when
replacing the lamp.
• Securely install the cover.
• If the power is not turned on even
• The lamp unit cover
when the lamp unit cover is
is open.
securely installed, contact your
nearest Sharp Authorised Projector Dealer or Service Centre for
advice.
-58
XV_Z200E_E_p57_66.p65
58
03.10.30, 13:15PM
Info
• If the temperature warning indicator illuminates, and the projector enters the standby mode, follow the possible solutions on the previous page and then wait until the projector has cooled down completely before
plugging in the power cord and turning the power back on. (At least 5 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and
the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the
AC outlet and then turn the power on again.
• If you want to clean the air vents during projector operation, be sure to put the projector into the standby
mode. After the cooling fan has stopped, clean the vents.
• The cooling fan keeps the internal temperatures of the projector constant and this function is controlled
automatically. The sound of the cooling fan may change during operation because the fan speed may change
and this is not a malfunction.
• Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan is
running. The cooling fan runs for about 90 seconds.
Regarding the Lamp
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality.
The lamp life (percentage) can be checked with the on-screen display. See page 51.
■ For lamp replacement, please consult your nearest Sharp Authorised Projector Dealer or Service Centre.
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure
largely varies depending on the individual lamp and/or the condition and the frequency of use. It is
important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, the glass particles may spread inside the lamp unit or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorised Projector
Dealer or Service Centre to remove the damaged lamp and assure safe operation.
Replacing the Lamp
Caution
• Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching
it can lead to burn or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
-59
XV_Z200E_E_p57_66.p65
59
03.10.30, 13:15PM
Appendix
■ If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorised
Projector Dealer or Service Centre for repair. Purchase a replacement lamp unit of type BQCXVZ200++1 from your nearest Sharp Authorised Projector Dealer or Service Centre. Then carefully
change the lamp by following the instructions described in this section. If you wish, you may have
the lamp replaced at your nearest Sharp Authorised Projector Dealer or Service Centre.
Regarding the Lamp
Removing and Installing the Lamp Unit
Lamp
unit
BQC-XVZ200++1
Caution
• Be sure to remove the lamp unit by the handle.
Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, carefully follow the steps below.
• Replace the lamp after turning off the power
and unplugging the power cord.
1
STANDBY button
Put the projector into the
standby mode.
• Press
.
• Wait until the cooling fan stops.
2
Unplug the power cord.
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
3
Remove the Swivel Stand. (See
page 24.)
4
Remove the lamp unit cover.
5
• Loosen the user service screw that secures the lamp unit cover.
• Slide the lamp unit cover in the direction of the arrow.
Power cord
User service
screw
Remove the lamp unit.
• Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of
the arrow.
-60
XV_Z200E_E_p57_66.p65
60
03.10.30, 13:15PM
6
Insert the new lamp unit.
7
Attach the lamp unit cover.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing screws.
• Slide the lamp unit cover in the direction of the arrow.
• Fasten the user service screw.
Resetting the Lamp
Timer
Reset the lamp timer after replacing the lamp.
1
Plug the power cord.
• Confirm that the POWER indicator illuminates red.
Power cord
UNDO button
2
ON button
Reset the lamp timer.
• Press
,
,
,
in order. Then press
,
and
INPUT button
.
• “LAMP 0000H” is displayed on the
screen.
ENTER button
Info
Appendix
• Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, the lamp may become damaged or
explode.
-61
XV_Z200E_E_p57_66.p65
61
03.10.30, 13:15PM
Cleaning the Ventilative Holes
• This projector is equipped with
ventilative holes to ensure the optimal operating condition of the projector.
• Periodically clean the ventilative hole
by vacuuming it off with a vacuum
cleaner.
• The ventilative holes should be
cleaned every 100 hours of use. Clean
the ventilative holes more often when
the projector is used in a dirty or
smoky location.
Side and Rear view
Bottom view
Intake ventilative holes
Intake ventilative holes
Swivel stand
Intake ventilative holes
Cleaning the
Ventilative Holes
1
STANDBY button
Put the projector into the
standby mode.
• Press
.
• Wait until the cooling fan stops.
2
Unplug the power cord.
Power cord
3
Clean the dust off by putting
the cleaner hose on the intake
ventilative holes.
Cleaner hose
-62
XV_Z200E_E_p57_66.p65
62
03.10.30, 13:15PM
Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a
Kensington MicroSaver Security System. Refer to the information that came
with the system for instructions on how
to use it to secure the projector.
Rear View
Kensington Security
Standard connector
Troubleshooting
Problem
Check
No picture appears.
• Projector power cord is not plugged into the wall outlet.
• Selected input is wrong. (See page 31.)
• Cables incorrectly connected to back panel of the projector. (See pages
14–23.)
• “Contrast” and “Bright” adjustments are set to minimum position. (See
page 44.)
Colour is faded or poor.
• Picture adjustments are not correct. (See page 44.)
Picture is blurred.
• Adjust the focus. (See page 25.)
• Projection distance is too long or too short to allow for proper focus. (See
pages 26 and 27.)
No OSD appears.
• OSD Display is set to “OFF”, preventing to display some or all On-screen
Displays. (See page 51.)
An unusual sound is
occasionally heard from the
cabinet.
• If the picture is normal, the sound is due to cabinet shrinkage caused by
temperature changes. This will not affect operation or performance of the
projector.
Maintenance indicator
illuminates.
• Refer to “Maintenance Indicators” on page 58.
Picture noise appears.
• Adjust the “Phase” setting. (See page 48.)
Image is green on INPUT 2
Component.
Image is pink (no green) on
INPUT 2 RGB.
• Change the input signal type. (See page 52.)
Appendix
-63
XV_Z200E_E_p57_66.p65
63
03.10.30, 13:15PM
Connecting Pin Assignments
DVI-I (INPUT 2 / DIGITAL INPUT) port : 29 pin connector
• DVI Digital INPUT
9
•••••••••
1 2
••••
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
~ • • • • • • • • • 16
~ •••• 7 8
C1
C2
C4
C5
C3
17
24
18
••••
~ • • • • 23
• DVI Analog RGB Input
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
DDC clock
DDC data
Vertical sync
Not connected
Not connected
Not connected
Not connected
Not connected
+5V power
Ground
Pin No.
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Signal
Pin No.
T.M.D.S data 2–
16
T.M.D.S data 2+
17
T.M.D.S data 2 shield
18
Not connected
19
Not connected
20
DDC clock
21
DDC data
22
Not connected
23
T.M.D.S data 1–
24
T.M.D.S data 1+
C1
T.M.D.S data 1 shield
C2
Not connected
C3
Not connected
C4
+5V power
C5
Ground
Signal
Hot plug detection
T.M.D.S data 0–
T.M.D.S data 0+
T.M.D.S data 0 shield
Not connected
Not connected
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock–
Not connected
Not connected
Not connected
Not connected
Ground
• DVI Analog Component Input
Signal
Hot plug detection
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Red
Analog input Green
Analog input Blue
Horizontal sync
Ground
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Ground
Pin No.
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Pr/Cr
Analog input Y
Analog input Pb/Cb
Not connected
Ground
RS-232C Port: 9-pin D-sub male connector
Pin No.
1
2
3
4
5
6
7
8
9
12345
6789
Signal
RD
SD
SG
Name
Receive Data
Send Data
Reserved
Signal Ground
Reserved
Reserved
Reserved
I/O
Input
Output
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
-64
XV_Z200E_E_p57_66.p65
64
03.10.30, 13:15PM
(RS-232C) Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 23 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digit
Response code format
Normal response
O
K
Return code (0DH)
Parameter 4-digit
Problem response (communication error or incorrect command)
E
Return code (0DH)
R
Return code (0DH)
R
Info
• When more than one code is being sent, send each command only after the OK response code for the
previous command from the projector is verified.
Note
• When using the computer control function of the projector, the projector’s operating status cannot be read by
the computer. Therefore, confirm the status by transmitting the display commands for each adjustment
menu and checking the status with the on-screen display.
Commands
Example:
• When power on.
Computer
P
O
W
R
_
_
1
COMMAND PARAMETER
→
←
Projector
O
K
RETURN
POWER ON
P O W R _ _ _ 1 OK OR ERR
STANDBY
P O W R _ _ _ 0 OK OR ERR
INPUT 1 (COMPONENT 1)
I V E D _ _ _ 1 OK OR ERR
INPUT 2 (COMPONENT 2)
I V E D _ _ _ 2 OK OR ERR
INPUT 3 (S-VIDEO)
I V E D _ _ _ 3 OK OR ERR
INPUT 4 (VIDEO)
I V E D _ _ _ 4 OK OR ERR
DIGITAL INPUT MODE
I V E D _ _ _ 5 OK OR ERR
Appendix
BUTTONS & REMOTE CONTROL BUTTONS
CONTROL CONTENTS
_
Note
• If an underbar (_) appears in the parameter column, enter a space.
-65
XV_Z200E_E_p57_66.p65
65
03.10.30, 13:15PM
Computer Compatibility Chart
Horizontal Frequency: 15–70 kHz
Vertical Frequency: 43–75 Hz
Pixel Clock: 12–80 MHz
Compatible with sync on green
XGA compatible in intelligent compression
PC/
MAC/
WS
Resolution
Horizontal
Frequency
(kHz)
640 ⳯ 350
720 ⳯ 350
640 ⳯ 400
VGA
720 ⳯ 400
640 ⳯ 480
PC
SVGA
XGA
800 ⳯ 600
1,024 ⳯ 768
Vertical
Frequency
(Hz)
27.0
60
31.5
27.0
70
60
31.5
70
27.0
60
31.5
70
VESA
Standard
DVI
Support
27.0
60
31.5
70
26.2
50
31.5
60
34.7
70
37.9
72
✔
✔
37.5
75
✔
✔
31.4
50
35.1
56
✔
✔
37.9
60
✔
✔
44.5
70
48.1
72
✔
✔
46.9
75
✔
✔
35.5
43
✔
✔
40.3
50
56.5
70
58.1
72
✔
✔
Display
Upscale
✔
✔
✔
✔
✔
✔
Intelligent
Compression
✔
✔
—
1,280 ⳯ 720
45.0
60
PC/
MAC 13"
VGA
640 ⳯ 480
34.9
67
MAC 16"
SVGA
832 ⳯ 624
46.8
75
49.6
75
PC/
MAC 19"
XGA
1,024 ⳯ 768
48.4
60
✔
60.0
75
✔
✔
Upscale
Intelligent
Compression
Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in
“CRT only” mode. Details on how to change display modes can be found in your notebook computer’s operation manual.
-66
XV_Z200E_E_p57_66.p65
66
03.10.30, 13:15PM
Specifications
Appendix
Product type Projector
Model XV-Z200E
Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480I/480P/720P/1080I
Display method DLP chip, RGB optical shutter method
DLP panel Panel size: 0.6⬙
Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
Drive method: Digital Light Processing (DLP™)
No. of dots: 589,824 dots (1,024 [H] ⳯ 576 [V])
Lens 1–1.2 ⳯ zoom lens, F1.75–2.04 f=28.0–33.5 mm
Projection lamp 210 W/168 W SHP lamp
Video input signal RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
S-video input signal 4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Component input signal RCA Connector
(INPUT 1) Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
Component input signal 29-pin connector
(INPUT 2) DVI input signal: Digital 250–1,000 mV 50 Ω
Analog 0.7 Vp-p 75 Ω
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
Horizontal resolution 520 TV lines (NTSC 3.58 input)
RGB input signal DVI-I terminal
<Digital>
Input impedance 50 Ω
Input level 250-1000 mV
<Analog>
Input impedance 75 Ω
Input level 0.7 Vp-p
<Synchronization signal>
• Separate sync/Composite sync
Input level TTL level
Input impedance 1 KΩ
• Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75 Ω
Pixel clock 12–80 MHz
Vertical frequency 43–75 Hz
Horizontal frequency 15–70 kHz
Computer control signal 9-pin D-sub connector (RS-232C Port)
Rated voltage AC 100–240 V
Input current 3.2 A
Rated frequency 50/60 Hz
Power consumption 285 W
Heat dissipation 1,070 BTU/hour
Operating temperature Ⳮ5°C to Ⳮ35°C
Storage temperature ⳮ20°C to Ⳮ60°C
Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 368 (W) ⳯ 153.8 (H) ⳯ 327 (D) mm (including swivel stand)
368 (W) ⳯ 118 (H) ⳯ 327 (D) mm (main body only)
Weight (approx.) 4.6 kg (including swivel stand)
4.1 kg (main body only)
Supplied accessories Remote control, Two AA size batteries, Power cord, 21 pin RCA conversion adaptor,
Video cable, Terminal cover, Screws for terminal cover, Lens cap (attached on the
body), Operation manual
Replacement parts Lamp unit (Lamp/cage module) (BQC-XVZ200++1), Remote control
(RRMCGA218WJSA), AA size batteries, Power cord for Europe except U.K.
(QACCV4002CEZZ), Power cord for U.K., Hong Kong and Singapore
(QACCBA012WJPZ), Power cord for Australia and New Zealand (QACCLA018WJPZ),
21 pin RCA conversion adaptor (QSOCZ0361CEZZ), Video cable (QCNWGA001WJZZ),
Terminal cover (GCOVAA116WJKB), Screws for terminal cover (XBBSN40P10000), Lens
cap (CCAPHA004WJ01), Operation manuals; for European 7 languages (TINSB007WJZZ) / for Chinese, Korean and Arabic (TINS-B008WJZZ)
This SHARP projector uses a DMD chip. This very sophisticated chip contains 589,824 pixels. As with any high
technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain
acceptable tolerances that the equipment must conform to.
Specifications are subject to change without notice.
-67
XV_Z200E_E_p67_70.p65
67
03.10.30, 13:15PM
Dimensions
Units: mm
Rear View
Top View
Side View
327
Side View
153.8
118
Front View
368
Bottom View
-68
XV_Z200E_E_p67_70.p65
68
03.10.30, 13:15PM
Glossary
Aspect Ratio
Gamma
Width and height ratio of an image. The normal
aspect ratio of a computer and video image is 4:3.
There are also wide images with an aspect ratio
of 16:9 and 21:9.
Auto Sync
Optimizes projected computer images by automatically adjusting certain characteristics.
Background
Initial setting image projected when no signal is
being output.
Clock
Clock adjustment is used to adjust vertical noise
when clock level is incorrect.
CLR Temp (Colour temperature)
Function that can be used to adjust the colour temperature to suit the type of image input to the projector. Decrease the colour temperature to create
warmer, reddish images for natural flesh tones,
or increase to create cooler, bluish images for a
brighter picture.
Image quality enhancement function that offers a
richer image by brightening the darker portions of
the image without altering the brightness of the
brighter portions. You can select from four different modes: Standard, Cinema 1, Cinema 2 and
Cinema 3.
Intelligent compression and expansion
High quality resizing of lower and higher resolution images to fit the projector’s native resolution.
Phase
Phase shift is a timing shift between isomorphic
signals with the same resolution. When phase level
is incorrect, the projected image typically displays
horizontal flicker.
Resize
Allows you to modify or customize the picture display mode to enhance the input image. You can
select from four different modes: SIDE BAR,
SMART STRETCH, CINEMA ZOOM and
STRETCH.
RS-232C
Composite sync
Signal combining horizontal and vertical sync
pulses.
Digital keystone correction
Function to digitally correct a distorted image when
the projector is set up at an angle, smoothes out
jaggies on keystone images and compresses the
image not only horizontally but vertically keeping
the 16 : 9 aspect ratio.
DVI (Digital Visual Interface)
Display digital interface that also supports analog
interfaces.
Function to control the projector from the computer by using the RS-232C ports on the projector and computer.
Stretch
Mode that stretches the 4:3 image horizontally to
display it on the wide screen.
Sync on green
Video signal mode of a computer which overlaps
horizontal and vertical sync signal to green colour
signal pin.
Appendix
-69
XV_Z200E_E_p67_70.p65
69
03.10.30, 13:15PM
Index
A
R
AC socket ............................................................. 14
Adjusting the Picture ............................................ 44
ADJUSTMENT buttons ........................................ 39
Aspect ratio .......................................................... 35
Automatic power shut-off function ........................ 54
Auto sync adjustment ........................................... 50
AUTO SYNC button ............................................. 50
Rear projection ..................................................... 28
Remote control ..................................................... 10
Remote control sensor ......................................... 11
Remote control signal transmitter ........................ 10
RESIZE button ..................................................... 35
RS-232C terminal ................................................ 23
B
STANDBY button ................................................. 32
STRETCH ............................................................ 36
S-VIDEO INPUT terminal ..................................... 15
Sync on green ...................................................... 66
Background .......................................................... 53
C
Ceiling-mount ....................................................... 28
Ceiling+Rear ........................................................ 56
Clock .................................................................... 48
COMPONENT terminals ...................................... 17
S
T
TEMPERATURE WARNING indicator ................. 58
U
D
UNDO button ........................................................ 39
DIGITAL INPUT terminal ...................................... 20
DVI ....................................................................... 20
V
E
VIDEO INPUT terminal ........................................ 16
Video System ....................................................... 52
Eco mode ............................................................. 53
ENTER button ...................................................... 39
Exhaust ventilative hole ......................................... 6
Z
Zoom knob ........................................................... 25
F
Focus ring ............................................................ 25
FREEZE button .................................................... 35
I
INPUT buttons ...................................................... 31
K
Kensington Lock .................................................. 63
KEYSTONE button ............................................... 33
L
LAMP indicator ..................................................... 58
Lens shift .............................................................. 25
M
MENU button ........................................................ 38
O
ON button ............................................................. 30
On-screen display ................................................ 51
On-screen display language ................................ 31
P
Phase ................................................................... 48
Power cord ........................................................... 14
POWER indicator ................................................. 30
-70
XV_Z200E_E_p67_70.p65
70
03.10.30, 13:15PM
XV-Z200E
XV-Z200E
PROJECTOR
PROJEKTOR
PROJECTEUR
PROJEKTOR
PROYECTOR
PROIETTORE
PROJECTOR
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
BRUKSANVISNING
MANUAL DE MANEJO
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
SHARP CORPORATION
Printed on 100% post-consumer recycled paper.
Gedruckt auf 100% wiederverwertungs Papier.
Imprimé sur 100% de papier recyclé.
Utskrift på återvunnet papper av 100% återvunnet material.
Impreso en 100% de papel reciclado de postconsumo.
Stampato su carta riciclata al 100%.
Gedrukt op 100% kringlooppapier.
XV_Z200E_E_Hyo1_4.p65
1
Printed in Japan
In Japan gedruckt
Imprimé au Japon
Triykt i Japan
Impreso en Japón
Stampato in Giappone
Gedrukt in Japan
TINS-B007WJZZ
03P11-JWM
03.10.30, 13:12PM
ENGLISH .............
-1 –
-70
DEUTSCH ............
-1 –
-70
FRANÇAIS ...........
-1 –
-70
SVENSKA ............
-1 –
-70
ESPAÑOL ............
-1 –
-70
ITALIANO .............
-1 –
-70
NEDERLANDS ....
-1 –
-70