Cissell CF 19 Specifications

Add to my manuals
29 Pages

advertisement

Cissell CF 19 Specifications | Manualzz

Form

Finishers

Models:

Suzie II

Mr. Cissell

Ms. Cissell

Sensi-Form

CISSELL MANUFACTURING COMPANY

HEADQUARTERS

831 SOUTH FIRST ST.

P.O. BOX 32270

LOUISVILLE, KY 40232-2270

PHONE: (502) 587-1292

SALES FAX: (502) 585-3625

SERVICE/PARTS FAX: (502) 681-1275

THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER.

MANCONS 8/00 IH

WARRANTY

The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1) year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with respect to all new repair or replacement parts for

Cissell equipment for which the one (1) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. The warranty period on each new replacement part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part replaced.

With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer.

Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective equipment or part returned f.o.b. Cissell's factory, transportation prepaid, within the applicable warranty period and found by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to persons or property or for any special or consequential damages. The liability of Cissell does not include furnishing (or paying for) any labor such as that required to service, remove or install; to diagnose troubles; to adjust, remove or replace defective equipment or a part; nor does it include any responsibility for transportation expense which is involved therein.

The warranty of Cissell is contingent upon installation and use of its equipment under normal operating conditions. The warranty is void on equipment or parts; that have been subjected to misuse, accident, or negligent damage; operated under loads, pressures, speeds, electrical connections, plumbing, or conditions other than those specified by Cissell; operated or repaired with other than genuine Cissell replacement parts; damaged by fire, flood, vandalism, or such other causes beyond the control of Cissell; altered or repaired in any way that effects the reliability or detracts from its performance, or; which have had the identification plate, or serial number, altered, defaced, or removed.

No defective equipment or part may be returned to Cissell for repair or replacement without prior written authorization from Cissell. Charges for unauthorized repairs will not be accepted or paid by Cissell.

CISSELL MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY, STATUTORY OR OTHERWISE,

CONCERNING THE EQUIPMENT OR PARTS INCLUDING, WITHOUT LIMITATION, A WARRANTY

OF FITNESS FOR A PARTICULAR PURPOSE, OR A WARRANTY OF MERCHANTABILITY. THE

WARRANTIES GIVEN ABOVE ARE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED. CISSELL NEITHER ASSUMES, NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT,

ANY OTHER WARRANTY OR LIABILITY IN CONNECTION WITH THE MANUFACTURE, USE OR SALE

OF ITS EQUIPMENT OR PARTS.

For warranty service, contact the Distributor from whom the Cissell equipment or part was purchased. If the Distributor cannot be reached, contact Cissell.

Page 1

TABLE OF CONTENTS

Cissell Equipment Warranty ................................................................................................. 1

Specifications and Dimensions ............................................................................................. 3

Installation Instructions ......................................................................................................... 4

Operation and Safety Precautions ....................................................................................... 5

Operation-Controls........................................................................................................6

Service Chart and Maintenance ......................................................................................... 7-8

Revolving Form Adjustment.........................................................................................8

Instructions for Removing and Replacing Bag............................................................9

Instructions for Tying Lower Tie String ............................................................................ 10

Replacement Form Bags ........................................................................................................ 11

Instructions for Adjsting Height of Revolving Form...................................................12

Mr. Cissell Form Assembly Parts ...................................................................................... 13-14

Waist, Hip, and Lower Control Parts .................................................................................. 15

Base and Blower Parts ........................................................................................................... 16

Ms. Cissell and Sensi Form Parts ..................................................................................... 17-18

Suzie II Parts................................................................................................................19

Front and Rear Paddle Assembly.................................................................................20

Steam Column and Piping Parts ......................................................................................... 21

Condenser and Spray Gun Parts ...................................................................................... 22-23

Damper Assembly Parts......................................................................................................... 24

Control Panel and Electrical Parts ...................................................................................... 25

Wiring Diagrams .................................................................................................................. 26-28

Page 2

OVERALL DIMENSIONS

NOTE:

Shown with Mr. Cissell Form. To figure the height from floor, add 7-3/4” (19.7cm) to the form heights listed below.

Mr. Cissell - 51” (130cm)

Ms. Cissell - 58-7/8” (150cm)

Sensi-Form - 58-7/8” (150cm)

Suzie II - 59-1/4” (150.49 cm)

SPECIFICATIONS

MS. CISSELL, SENSI-FORM

CF600

MR. CISSELL

CF100

SUZIE II

Electrical

1 H.P. Motor

115V, 50/60 Hz., 1 Ph, 12 Amps

230V, 50/60 Hz., 1 Ph, 6 Amps

Maximum Operating Pressure

Boiler Horsepower Required

Steam Supply & Return Lines

Net Weight

Shipping Weight

Export Shipping Dimensions

Export Crate Volume

100 P.S.I. (6.9 Bars)

2.5 H.P. (1.9 kw)

1/2" (1.27 cm)

220 lbs. (100 kg)

250 lbs. (113 kg)

61" x 25" x 69"

(155 cm x 64 cm x 175 cm)

61 Cubic Feet (1.73 m 3 )

1 H.P. Motor

115V, 60 Hz., 1 Ph, 6 Amps

230V, 60 Hz., 1 Ph, 3 Amps

230V, 50 Hz., 1 Ph, 3 Amps

100 P.S.I. (6.9 Bars)

2 H.P. (1.5 kw)

1/2" (1.27 cm)

220 lbs. (100 kg)

250 lbs. (113 kg)

61" x 25" x 69"

(155 cm x 64 cm x 175 cm)

61 Cubic Feet (1.73 m 3 )

1 H.P. Motor

115V, 60 Hz., 1 Ph, 6 Amps

230V, 60 Hz., 1 Ph, 3 Amps

115V, 50 Hz., 1 Ph. 3 Amps

100 P.S.I. (6.9 Bars)

2 H.P. (1.5 kw)

1/2" (1.27 cm)

220 lbs. (100 kg)

250 lbs. (113 kg)

61" x 25" x 69"

(155 cm x 64 cm x 175 cm)

61 Cubic Feet (1.73 m 3 )

Page 3

INSTALLATION INSTRUCTIONS

NOTE: This machine should be installed by qualified service personnel only.

1. Uncrate the machine. Check the nameplate voltage and current; match it with the power being connected.

2. Set the machine in position and bolt to floor.

3. Connect Water Spray Gun to machine. Remove the Lint Screen to access the connection.

Open the valve on the Condenser and replace the Lint Screen.

4. Connect steam supply line as shown in illustration.

5. Connect steam return line as shown. NOTE: Before final return line connection is made, open the steam supply valve and blow all foreign matter out of the steam lines. Failure to do so will cause trap to leak.

6. Make electrical connections in junction box on rear of machine, following applicable electric codes. Include a fused disconnect switch or circuit breaker with “slow-blow” characteristics and be capable of carrying 15 amps, 115 volts or 8 amps, 230 volts.

7. Install the revolving form on the machine.

8. Turn on the electric power to machine. Remove the plastic cover from the bag. Open the steam lines.

9. Test the machine, following the OPERATING INSTRUCTIONS in this manual.

Page 4

SAFETY PRECAUTIONS

Please read these warnings before operating or servicing machine.

CAUTION: This machine emits hot steam. To prevent burns, avoid contact with hot steam. Before service machine, close steam supply valve and purge lines.

CAUTION: Shut off electrical supply before servicing to avoid electrical shock.

OPERATING INSTRUCTIONS

1. Machine can be operated from any side. Position foot switches at convenient location.

2. Place garment on form. Adjust shoulder form width by turning knob in either direction. The Mr.

Cissell form requires adjustment of the Waist, Hip and Lower control knobs. After adjusting lock the controls by twisting the knobs clockwise.

3. Press the AIR foot switch to operate the blower for sizing the form bag. Size the bag by adjusting the DAMPER CONTROL. Using the Control Panel, press the MODE SELECT until the AIR light glows and press START/CANCEL to operate the blower, then proceed with sizing the bag.

4. Set the three control timers to the recommended settings:

Steaming: 6-9 seconds

Conditioning: 4-9 seconds

Drying: 12-16 seconds

These settings should be fine-tuned to the particular garment, steam pressure and ambient conditions. The recommended cycle is the steam/air conditioning and the drying. The control will power up in this cycle.

5. This machine has the ability to pre-steam a garment prior to the automatic finishing cycle. To actuate this cycle, press the MODE SELECT pad until the PRE-STEAM LIGHT glows, then press

START. Using the foot switch, press PRE-STEAM.

6. If a cycle is operating, it can be cancelled at any time by pressing any foot switch or control panel pads.

Control Panel

Page 5

OPERATION - CONTROLS

Page 6

SERVICE CHART

CAUTION: BEFORE SERVICEING MACHINE, SHUT OFF ELECTRICAL POWER TO

AVOID POSSIBLE ELECTRICAL SHOCK. SHUT OFF STEAM SUPPLY AND PURGE

PRESSURE FROM STEAM LINES TO AVOID BURNS FROM HOT STEAM.

REFER TO PARTS SHEETS FOR CORRECT REPLACEMENT PARTS.

PROBLEM

(1) No Steam

(2) No Air

(3) Steam Valve Leaks

(4) Wet Steam

CAUSE

A. Steam supply valve closed.

B. Electric power off.

C. Bad solenoid valve coil.

D. Steam timer may slip on shaft and be set on “0”.

See item 11.

A. Damper closed.

B. Drying timer slipping.

C. Defective motor relay.

D. Blower wheel stuck.

E . Defective motor.

F. Defective motor capacitor.

See items 1B and 11.

A. Defective steam valve.

A. Trap not operating.

B. Check valve problem.

C. Strainer clogged.

D. Return line closed.

E . Steam cycle set too long.

F. Steam lines installed wrong.

G. Heavy condesate in supply.

H . Units not trapped correctly.

I.

Back pressure in return line.

REMEDY

Open valve in steam supply line.

Check for blown fuse, tripped circuit breaker or loose wire connection. Tighten wire nuts and restore power.

Disconnect power and measure coil resistance. A good coil should be between 50-125 hms. Replace coil if not within these parameters.

Loosen set screw and remove knob shaft. Turn shaft to maximum counter-clockwise position. Attach knob to shaft pointing to “0” and tighten set screw.

Open damper.

See item 1D.

Disconnect and measure resistance of relay coil. A good coil should be between 240-360 ohms. Replace coil if not within these parameters.

Check wheel by moving by hand. If wheel rubs or is stuck, loosen the set screws and align the wheel on the shaft. Tighten set screws.

Measure the resistance of the black and white wires on the motor terminal board. They should be between 5-20 ohms. Replace motor if not within these parameters.

If relay, blower wheel, and motor are good, replace motor.

Replace valve.

Check size and operation of trap.

Refer to the Installation Instructions and make corrections in installation if needed. Replace trap if defective.

Check for proper installation.

Replace if bad.

Clean or replace as needed.

Open return line.

Reduce steam timer setting.

Refer to steam line Installation

Instructions.

Install by-pass from supply header to return line.

Each machine needs separate trap.

Check trap installation. Return lines must be gravity fed to condensate tank. Properly vent the condensate tank.

Page 7

PROBLEM

(5) Water inthe base.

(6) Noisy or vibration.

(7) Not enough steam.

(8) Too much steam.

(9) Too much air.

(10) Form will not inflate.

(11) Timer control does not function.

SERVICE CHART

CAUSE

A. Wet steam.

B. Steam leak in machine.

See items 3, 4, and 8.

A. Foreign object in blower.

B. Wheel out of balance.

C. Wheel loose on shaft.

D. Motor mount bent.

E . Motor bearings bad..

See items 1A, 1D, or 11.

Timer set too long.

See item 11.

Timer set too long.

See item 11.

A. Damper is closed.

See items 2 and 11.

A. No power on control.

B. Moisture accumulated.

C. Timer control bad.

REMEDY

See item 4.

Inspect and repair or replace leaking part.

Remove foreign object.

Inspect wheel for loose weights, out of round or damage. Repair or replace as needed.

Tighten set screws on wheel hub.

Repair or replace as needed.

Repair or replace as needed.

Reset timer.

Reset timer.

Open damper; check damper control linkage and reapir or replace as needed.

Check fuse on back of control, replace if needed.

Check for steam or water leaks.

Dry out control.

Replace timer control.

REVOLVING FORM ADJUSTMENT

If the Revolving Form drags on the base rather than turning freely, it must be raised. First remove the form by lifting it straight up off the base. Then loosen the Bearing Locknut and turn the Bearing

Adjustment Screw counter-clockwise. Check adjustment by replacing form and rotate. Repeat adjustment if needed.

If Revolving Form is too high above base, steam will escape from between the base and the bottom of the form. To correct, first remove form from the base. Then loosen the Bearing Locknut and turn the

Bearing Adjustment Screw clockwise. Replace form on the base and check adjustment. Repeat if needed.

MAINTENANCE RECOMMENDATION

Change the air filter located on the rear of the machine at least every six months depending on the use and environmental conditions. See the parts section of this manual for the replacement part number.

Page 8

INSTRUCTIONS FOR REMOVING & REPLACING BAG

(1) Remove yellow weights,

1 each side.

t

(4) Replace yellow

weights, one each

side, on end of

control strings t

(2) Raise the lower control

ring (inside bag).

(3) Open zipper and untie

bottom string t

(4) Lift bag off of revolving

assembly shoulder form.

(3) Lower the control

ring inside bag.

t

(2) Tie bottom string

in groove and close

zipper. Refer to

instructions on

next page for

proper knot when

tying string.

Straighten bag

until control

strings are at the

sides

(1) Place bag over

revolving assembly

shoulder form,

with front of bag

toward front of

form.

Page 9

INSTRUCTIONS FOR TYING LOWER TIE STRING

Page 10

REPLACEMENT FORM BAGS

MS. CISSELL

Part No. F1310

SENSI-FORM

Part No. F1311

MR. CISSELL

Part No. FD10

SUZIE II

Part No. F833

Page 11

CISSELL STEAM-AIR FINISHER

INSTRUCTIONS FOR ADJUSTING HEIGHT

OF REVOLVING FORM

Should the revolving form “drag” on the base rather than turn freely, the form must be raised.

Conversely, if the revolving form hides too high above the base, permitting steam to escape from the space between the form and base, the form must be lowered.

WHEN ADJUSTMENT MUST BE MADE, REMOVE REVOLVING FORM BY SIM-

PLY LIFTING IT STRAIGHT UP OFF THE BASE.

PROBLEM: Revolving form “drags” on base.

TO CORRECT: Loosen F286 Bearing Lock Nut. Turn F287 Bearing Adjustment

Screw COUNTERCLOCKWISE

CHECK ADJUSTMENT: Replace revolving form on base. Rotate form. If perfectly adjusted, form will rotate freely and snugly on felt seal around top of base. If form is still too low... or too high...repeat adjustment until it is correct.

PROBLEM: Revolving Form rides too high above base.

TO CORRECT: Loosen F286 Bearing Lock Nut. Turn F287 Bearing Adjustment

Screw CLOCKWISE.

CHECK ADJUSTMENT: Replace revolving form on base. Rotate form. If perfectly adjusted, form will rotate freely and snugly

on felt seal around top of base. If form is still too high... or too low... repeat adjustment until it is correct.

Page 12

MR. CISSELL REVOLVING FORM ASSEMBLY

Page 13

Ref. No.

29

30

31

32

25

26

27

28

21

22

23

24

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

37

38

39

40

33

34

35

36

41

42

43

44

*Not part of F22 Assembly

Part No.

F303

F302

F332

F333

F104

F335

F151

F137

F432

F433

F888

F240

F243

F237

F267

F304

F533

F140

F279

F289

F9

F842

F11

F24

F192

F381

F492

F493

F494

F336

F197

F317

F334

F434

F435

F427

F436

F437

F218

F438

F63

F534

F122

P104

MR. CISSELL REVOLVING FORM ASSEMBLY - F22

NOTE: See next page for Waist, Hip, and Lower Controls.

Description

Insulating Gasket

Knob, Pin, & Adjusting Rod

Shoulder Form

Shoulder Extension

Bearing Plate

Shoulder Link

Shoulder Tension Spring

Shoulder Lever

Control Box & Pan Assembly

Clamp Bearing Bolt

Thrust Bearing

Cup & Bearing Assembly with Hardware

Cloth Steam Spreader

Vent Clamp*

No. 11 Wooden Sleever*

No. 24 Wooden Sleever*

Front Paddle only

Sponge only

“E” Ring (3/16”)

Clamp Slide Support Pin

Slide Spring Clip

Clamp Slide

Pivot Pin

Waist Index Plate

Hip & Lower Index Plate

Control Slides

Front Plate

Front Latch

Trigger Release

Clamp Latch Rod

Compression Latch Spring

Latch Plunger

Front Handle Assembly

Rear Paddle only

Sponge only

Back Latch

Front Paddle & Sponge Assembly

Rear Handle Assembly

Clamp Leaf Spring

Rear paddle & Sponge Assembly

Covered Spring Assembly

Revolving Form Frame

Locknut (1/4” - 28)

Washer

Page 14

WAIST, HIP, AND LOWER CONTROLS

Ref.

N o .

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

Part

N o .

F324

F325

F490

V2

P39

F429

F439

F440

F322

F323

F321

F301

F300

F319

F318

F377

D e s c r i p t i o n

Waist Control Knob

Hip Control Knob

Lower Control Knob

Spacer

Spacer

Actuating Lever

Actuating Lever

Bearing Pin

Bearing Pin

Connecting Link

Draw String Lever

Cotter Pin

Yoke, Pin & Cotter Pin

Tension Spring

Hip Lever Rod

Waist Lever Rod

Ref.

N o .

Part

N o .

D e s c r i p t i o n

17 040113282 Bead Chain (order by length)

18

23

24

25

26

19

20

21

22

27

28

29

30

31

F442

F443

F888

F444

F445

F446

F447

F448

F449

F450

F331

F451

F1003

F1004

Cord, Beads, &

Couplings Set

2 Pins & 4 “E” Rings

“E” Ring

2 Pins & 4 “E” Rings

2 Pins & 4 “E” Rings

Swivel & Chain Coupling

Spacer

Lower Swivel Arm

Hip Swivel Arm

Lever

Bearing Pin

Lower Lever Rod

Lower Lever Rod Assembly

Hip Lever Rod Assembly

Page 15

BASE ASSEMBLY PARTS

Ref.

N o .

3

4

1

2

5

6

7

8

9

10

11

12

13

Part

N o .

D e s c r i p t i o n

F11

F24

Sleever (11”)

Sleever (24”)

F842 Vent Clamp

F1319 Screen Retainer

F1427 Filter

---Control Panel

(see separate page)

F1238 Base Top

TU7733 #8 x 1/2” Screw

F1203 Base Bottom

F1290 Rear Jacket

F1264 Fan Housing

FG292 Blower Wheel

RC344 1/4 - 20 x 3/4” Screw

Ref.

N o .

17

18

19

20

13

14

15

16

21

22

23

24

25

Part

N o .

D e s c r i p t i o n

RC344 1/4 - 20 x 3/4” Screw

TU2846 1/4” Lockwasher

AF130 Motor Mounting Hardware

SB180 Junction Box Cover

F1265 Lower Rear Cover

TU2947 1/4” Flat Washer

TU2814 5/16” Lockwasher

AF131 Motor Mounting Bracket

MTR297 Motor, 115-230/50-60/1

C363 5/16” x 1-1/4” Bolt

FG226 Inlet Cone

C249 5/16” Hex Nut

F1463 Angle Seal

Page 16

MS. CISSELL, SENSI-FORM REVOLVING FORM ASSEMBLY

Page 17

Ref. No.

1

30

31

32

33

26

27

28

29

22

23

24

25

18

19

20

21

14

15

16

17

10

11

12

13

8

9

6

7

4

5

2

3

38

39

40

41

34

35

36

37

42

43

44

45

Part No.

F517

F859

F279

F1309

FG277

TU4787

AF207

AF176

F433

F432

F237

F243

F888

F240

F267

AF157

F122

F381

F192

F493

F492

F494

F197

F336

F317

TU3477

FB187

FB185

F1242

TU3480

F431

PT355

F860

FG135

F359

FG288

F489

FG450

F197

F950

FG443

FB187

F901

F1188

F949

MS. CISSELL, SENSI-FORM REVOLVING FORM ASSEMBLY

Description

Adjustable Shoulder Form -

consists of Parts 2-9.

Knob & Rod Assembly

Insulating Gasket

Shoulder Extension

Shoulder

Bearing Plate

Tension Spring

Shoulder Link

Shoulder Lever

#10 - 24 x 1/2” Screw

#10 Lockwasher

#10 - 24 Hex Nut

Revolving Form

#10 - 24 x 5/8” Screw

Bearing Cup

1/4” Hex Nut

Washer

1/4” - 20 x 1/2” Screw

Thrust Bearing

Shell Assembly

S t u d

3/8” - 16 x 9/16” Jam Nut

Cloth Cover

Front Paddle Clamp Assembly

Sponge

Front Paddle Channel

Clamp Slide

Slide Spring Clip

Retaining Ring

P i n

Pivot Pin

Trigger Release Assembly

1/4” - 28 Hex Nut

Handle

Retaining Ring

P i n

Retaining Ring

Latch Pin

Spring

Washer

Latch Rod

Lockwasher

#10 - 24 x 3/8” Screw

Leaf Clamp Spring & Pivot

Pivot Pin

Page 18

SUZIE II REVOLVING FORM FG236

ITEM# PART# DESCRIPTION

F517 Adjustable Shoulder Assembly

1-2

7

8

9

10

5

6

3

4

33

34

35

36

29

30

31

32

25

26

27

28

21

22

23

24

Not Illustrated

F381

F49

F192

F492H

F493

F336

F494H

F197

F317

15

16

17

18

19

11

12

13

14

FG219

FG220

FG222

FG223

TU2089

FG201

FG444

FG202

F289

FG291 Revolving Form Shell Assembly

PT355

F860

F859

F359

TU3480

F122

FB201

FG284

FG156

AF207

FG264

TU3478

P104

FB185

TU3477

M271

Knob, Shoulder Adjustable Rod & Pin

Rod & Pin

Shoulder Lever Pin*

Pyroid Gasket

Shoulder

Sliding Shoulder

Shoulder Connecting Link

Bearing Plate

Shoulder Tension Spring

Shoulder Lever

FG290 Revolving Form Frame Assembly

F833

F816

FG310

FG311

Frame Assembly

Pivot Plate Assembly

3-5/8" x 1/4" Pin

4-1/2" x 1/4" Pin

Spring

Support Rod

Yoke

Weight Ring

Bearing Assembly

Turning Arm Knob

Cloth Steam Spreader

Shell Assembly

#8-32 x 1/2" Pan Head Screw*

1/4" Brass Cut Washer*

#10-24Hex Nut*

#10-24 x 1/2" Flat Head Screw*

3/16" Split Lockwasher*

1/4"-20 S.S. Hex Head Nut

1/4" S.S. Split Lockwasher

1/4"-20 x 1/2" S.S. Screw*

Retaining Rings*

#10-24 Round Head Screw*

1/4"-28 Brass Nut*

Cotter Pin*

1/4" x 5/8" Roll Pin*

Nylon Bag

Net Overbag

Bag Weights 50 CY. 2" x 1-1/8"

Bag weights 60 CY. 2" x 1-1/2"

(*Shipped as a package of 6)

Page 19

FG137 Front Paddle Ass’y 36” FG164 Rear Paddle Ass’y 24”

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

Ref.

No.

Part

No.

Description

FG137WH Front Paddle Ass’y 36”

FG164WH Rear Paddle ass’y 24”

F433

F432

F237

F243

F240

F267

F218

F104

F949

F1121

F136

FG443

FG135

F197

FG450

FG287

Sponge (36”)

Paddle Channel (36”)

Clamp Slide

Slide, Spring (2 Req’d)

Slide Pin, (2 Req’d.) (1/8”)

Pivot Pin (1/8”)

Clamp Leaf Spring

Handle Trigger

Handle Pin (3/16”)

Rod Hinge Pin (3/16”)

Rod Hinge

Latch Rod

Handle Welded Ass’y

Spring

Latch Pin

Clamp Base

Ref.

N o .

Part

N o .

17 FG277

18 FG288

19 F435

20 F434

21 F901

22 F842

23 F904

24 F24

25 F11

26 ET183

27 F888

28 F122

29 F950

30 F489

31 TU4787

32 FB187

D e s c r i p t i o n

Stud

Pin (3/8”)

Sponge (24”)

Paddle Channel (24”)

#10 - 24 x 3/8” Hex. Hd. Screw*

Vent Clamp

Sandpaper & Sponge Set for F842

#24 Sleever

#11 Sleever

“E” Ring for 1/8” Pin*

“E” Ring for 3/16” Pin*

1/4” - 28 Brass Nut

3/8” Cut Washer*

“E” Ring for 3/8” Rod*

3/8” - 16 Hex Nut*

#10 Split Lockwasher*

Page 20

STEAM COLUMN & PIPING PARTS

Ref.

N o .

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

Part

N o .

D e s c r i p t i o n

F1227 Steam Chamber Column

F1269 Bearing Support Frame

F286

F287

Bearing Locknut

Bearing Adjustment Screw

F542 Pipe Plug

F1292 Union

390401016 3/8” x 2” Pipe Nipple

F1289 Solenoid Valve

F1296 Steam Nozzle

F1394 Steam Spreader

F1397 Pipe Nipple (3/8” x close)

F894 Drawband

IB139 3/8” - 16 x 1-1/4” Bolt

VSB134 3/8” Lockwasher

IB140 3/8” Flat Washer

F1449 Connector Flare

Ref.

Part

N o .

N o .

D e s c r i p t i o n

24

25

26

27

29

30

17

18

F1456 Coil Supply Tube Ass’y (CF100)

F1458 Coil Supply Tube Ass’y (CF600)

F1324 Steam Coil (CF100)

F1288 Steam Coil (CF600)

19

20

F1399 1/4” - 20 x 1” Screw

(see page 19)

22 400518040 Insulation (order by length)

23

31

FG143 Pipe Tee

SC196 Pipe Weldment

SC505 Coupling

F1461 Elbow w/Fitting

F1439 Condenser

F896 Drawband Eye

F1457 Coil Return Tube Ass’y (CF100)

F1459 Coil Return Tube Ass’y (CF600)

F1448 Column Supply Tube Ass’y

Page 21

Ref. No.

7

8

5

6

3

4

1

2

9

10

11

Part No.

J42

P530

SGV35

SF274

SG38

J 3

136067752

F1273

OP225

F1441

SG043

SK043

Description

Hose Clamp

Elbow - 1/4” x 1/8”

Adapter

Spray Gun Hose

Spring

Small Hose Clamp

Insulation (order by length)

Spray Gun Pipe

Straight Connector - 1/8” NPT x 1/4” Tube

(see page 19)

Spray Gun

Repair Kit for Spray Gun consists of a plunger tube, strainer, nozzle, and 2 gaskets

Page 22

F1447 - CONDENSER COIL ASSEMBLY

Ref. No.

7

8

5

6

3

4

1

2

9

10

11

12

13

Part No.

F725

F1440

F1441

F1439

F1445

RC382

F1446

TU2847

PT355

OP297

BR61

SU65

F1461

Description

Screw 10 - 24 x 5/8” (2 req’d)

Valve - 1/4” Globe

Manifold - Spray Gun

Condenser Coil

Plate - Coil Support

Lock Nut - 1/4” - 20

Threaded Rod - 1/4” - 20

Washer

Nut - 1/4” - 20

Compression Fitting

Bushing

Nut Compression w/PU8 Bead

Elbow

Page 23

DAMPER ASSEMBLY PARTS

Ref. No.

13

14

15

16

17

9

10

11

12

7

8

5

6

3

4

1

2

Part No.

D16

RC344

TU2847

F660

F750

TU4934

F1216

F664

SV332

F358

F639

F1280

F1283

F1222

TU7733

F645

F1438

Description

Control Knob

1/4” - 20 x 3/4” Screw

1/4” Cut Washer

Rubber Washer

Shaft

1/4” - 20 Nut

Damper Control Lever

Swivel

#8 - 32 x 3/8” Screw

Retaining Ring

Washer

Damper Tube

Damper Wire

Damper Plate

#8 x 1/2” Screw

Tube Clamp

Wire Clamp

Page 24

CONTROL PANEL & ELECTRICAL PARTS

Ref. No.

1

8

9

6

7

4

5

2

3

10

11

12

Part No.

F1301

F1305

TU8629

TU7733

F1300

F1302

F1243

F1259

ET250

SF259

F1406

F1325

F1396

F1304

Description

Transformer (120/24V)

Transformer (200-240/24V)

Terminal Board

#8 x 1/2” Screw

Relay

Capacitor (1 H.P. Motor)

Foot Switch Assembly

Control Panel

Electronic Timer

Damper Control Label

#8 Black Anodized Screw

Wire Tie

Wire Tie Mount

Wire Harness (not shown)

Page 25

Page 26

Page 27

Page 28

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals