Samsung SMM-21FDQ User guide

COLOR DUAL QUAD
OBSERVATION SYSYTEM
SMM-15FDQ/21FDQ
User Guide
Manuel d'utilisation
Guía del usuario
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Read these instructions.
Keep these Instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachment/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long
periods of time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
English-2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Graphic Symbol Explanation
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated ‘dangerous voltage’ within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Warning - To Prevent Fire or Shock Hazard, Do Not
Expose This Monitor To Rain or Moisture.
English-3
IMPORTANT SAFEGUARDS
Caution
Power source is indicated on the rear of the set. It contains high-voltage parts.
If you remove the cover, it may cause fire or electric shock. Do not remove the
cover by yourself. (Control switches are at the front of the monitor.)
1. Read Instructions : All the safety and operating instructions should be
read before the appliance is operated.
2. Retain Instructions : The safety and operating instructions should be
retained for future reference.
3. Heed Warnings : All warnings on the monitor and in the operating
instructions should be adhered to.
4. Follow Instructions : All operating and user instructions should be
followed.
5. Cleaning : Unplug this monitor from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
Exception. A monitor that is meant for uninterrupted service and that for
some specific reason, such as the possibility of the loss of an
authorization code for a CATV converter is not intended to be
unplugged by the user for cleaning or any other purpose may exclude the
reference to unplugging the monitor in the cleaning description
otherwise required in Item 5.
6. Attachments : Do not use attachments not recommended by Samsung
as they may cause hazards.
7. Water and Moisture : Do not use this monitor near water for example,
near a bathtub, wash bowl, kitchen sink or laundry tub in a wet basement
or near a swimming pool and the like wet basement or near a swimming
pool and the like.
English-4
8. Accessories : Do not place this monitor on an unstable cart, stand,
tripod, bracket or table. The monitor may fall, causing serious injury to a
child or adult and serious damage to the appliance. Use only with a cart,
stand, tripod. bracket or table recommended by Samsung or sold with
the monitor. Any mounting of the monitor should follow Samsung’s
instructions and should use a mounting accessory recommended by
Samsung.
9. Ventilation : Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the monitor and to protect
it from overheating and these openings should never be blocked by
placing the monitor on a bed, sofa, rug or other similar surface. This
monitor should never be placed near or over a radiator or heat register.
This monitor should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or Samsung’s
instructions have been adhered to.
10. Power Sources : This monitor should be operated only from the type of
power source indicated on the making label. If you are not sure of the
type of power supply to your installation site, consult your Samsung
dealer or local power company.
11. Grounding or Polarization : For monitors equipped with a 3-wire
grounding-type plug having a third(grounding) pin. This plug will only
fit into a grounding type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the
grounding-type plug.
12. Power : Cord Protection-Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles and the point where they exit from the monitor.
English-5
13. Lightning : For added protection for this monitor during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the cable system. This will
prevent damage to the monitor due to lightning and power-line surges.
14. Overloading : Do not overload wall outlets and extension cords as this
can result in a risk of fire of electric shock.
15. Object and liquid Entry : Never push objects of any kind into this
monitor through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the monitor.
16. Servicing : Do not attempt to service this monitor yourself as opening or
removing cover may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
17. Damage Requiring Service : Unplug this monitor from the wall outlet
and refer servicing to qualified service personnel under the following
conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the monitor.
c. If the monitor has been exposed to rain or water.
d. If the monitor does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and require extensive work by a qualified
technician to restore the monitor to its normal operation.
e. If the monitor has been dropped or the cabinet has been damaged.
f. When the monitor exhibits a distinct change in performance-this
indicates a need for service.
English-6
18. Replacement Parts : When replacement parts are required, be sure the
service technician has used replacement parts specified by Samsung or
have the same characteristics as the original parts.
Unauthorized substitutions may result in fire, electric shock or other
hazards.
19. Safety Check : Upon completion of any service or repairs to this
monitor, ask the service technician to preform safety checks to
determine that the monitor is in proper operating condition.
FCC & ICES Information
Warning
This equipment has been tested and found to comply the limits for a class A
digital device, pursuant to part 15 of the FCC Rules and ICES-003 of
Industry Canada.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generate, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
User-Installer Caution
Your authority to operate this FCC verified equipment could be voided if
you make changes or modifications not expressly approved by the party
responsible for compliance to part 15 of the FCC Rules.
English-7
Information to user
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
If necessary, consult your dealer or an experienced radio/television
technician for additional suggestions.
You may find the booklet called How to Identify and Resolve Radio/TV
Interference Problems helpful.
This booklet was prepared by the Federal Communications Commission.
It is available from the U.S. Government Printing Office, Washington, DC
20402, Stock Number 004-000-00345-4.
English-8
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD.
America QA Lab of Samsung
3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA
IC Compliance Notice
This Class (A) digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe (A) respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numéique de la classe A est conforme à la norme NMB-003 du
Canada.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
English-9
Contents
IMPORTANT SAFETY INSTRUCTIONS .................................. 2
IMPORTANT SAFEGUARDS..................................................... 4
FCC & ICES Information.............................................................. 7
Chapter 1:
System Components and Installation
1-1) Environmental requirements for installation and safety ..... 12
1-2) System Components............................................................. 13
1-3) CAMERA composition and installation method ................ 14
1-4) CAMERA Composition and Connecting Method
to MONITOR ....................................................................... 26
1-5) External terminal connecting method for CAMERA and
MONITOR ........................................................................... 27
1-6) Whole System connection and configuration ...................... 28
Chapter 2:
MONITOR FRONT PANEL KEY Function and
Using Method
2-1) TALK KEY.......................................................................... 29
2-2) AUD/SP SEL KEY .............................................................. 29
2-3) VOL+/VOL- KEY ............................................................... 29
2-4) POWER SAVE- KEY.......................................................... 30
2-5) ALARM RESET- KEY ....................................................... 30
2-6) QUAD/PAGE- KEY ............................................................ 30
2-7) LIVE/VCR- KEY................................................................. 30
2-8) PIP- KEY ............................................................................. 31
2-9) FREEZE- KEY .................................................................... 31
2-10) SEQUENCE- KEY ............................................................ 31
2-11) ZOOM- KEY ..................................................................... 31
2-12) POWER- KEY ................................................................... 31
2-13) ENTER- KEY .................................................................... 32
2-14) MENU- KEY ..................................................................... 32
English-10
Chapter 3: Setting each item function at SETUP MENU
3-1) ADJUST MENU function and setting method .................... 33
3-2) DATE/TIME MENU Function setting ................................ 34
3-3) DWELL TIME MENU function setting .............................. 34
3-4) DISPLAY MENU function setting ..................................... 35
3-5) TITLE MENU Function setting........................................... 36
3-6) ALARM MENU Function setting........................................ 37
3-7) VIEW EVENT LOG MENU function and
setting method ...................................................................... 38
Chapter 4: DISPLAY MODE setting method
4-1) SINGLE SCREEN DISPLAY ............................................. 39
4-2) QUAD MODE DISPLAY ................................................... 40
4-3) AUTO SEQUENTIAL DISPLAY MODE .......................... 41
4-4) PIP MODE DISPLAY ......................................................... 42
4-5) ZOOM MODE DISPLAY ................................................... 43
Chapter 5: Each product feature
SOD14C (Standard Camera) ....................................................... 44
SMM-PIRCAM : PIR Camera..................................................... 45
OBSERVAION MONITOR........................................................ 46
English-11
Chapter 1: System Components and Installation
1-1) Environmental requirements for installation and safety
This section describes the environmental requirements for safe installation and use.
Install the product on a flat table or in a rack. It should be used only when level and should not be
used when stood vertically or obliquely. The location in which the main system is installed and the
configuration of the wiring room are very important for proper operation of the system.
When the products are installed too closely together or the location is poorly ventilated, the system
may not operate properly and maintenance of the system may be difficult. Sufficiently circulate the
air within the system operating room and tightly fasten the cover of the main system to prevent
malfunction and reduce system downs due to environmental causes.
There are high voltage parts inside. Do not arbitrarily open the cover.
Install the product in a place that meets the following environmental conditions. Be sure to maintain
the system under the temperatures and humidity conditions given below:
•
Operating temperature: 0°C ~ 40°C
•
Storage temperature: -20°C ~ 60°C
•
Operating humidity: 20% ~ 85% RH
•
Storage humidity: 20% ~ 95 RH
•
Input voltage: AC 120V
•
Power usage: less than 110 Watts
•
Frequency: 60Hz
Caution
When operating the product, the fluctuation of input voltage must be within 10% of the rated voltage
and the external power outlet must be grounded, otherwise, it may cause electric shock or malfunction
of the product. Do not connect heat-generating appliances such as a hair dryer, iron or refrigerator to the
same power outlet in which the product is plugged, otherwise it may cause a fire or malfunction of the
product. The use of an Automatic Voltage Regulator (AVR) is highly recommended to ensure that
stable power is supplied. Be sure to coil CORE-FERRITE on the connector to reduce electro-magnetic
interference (EMI).
English-12
1-2) System Components
The system consists of the following:
STANDARD
CAMERA
MONITOR
CAMERA BRACKET
VCR CABLE
PIR CAMERA
POWER CODE &
INSTALLATION MANUAL
CAMERA CABLE
SENSOR
CONNECTOR
ITEM
MODEL
DESCRIPTION
MONITOR
SSC-21DQ/15DQ
21"/15" FLAT CRT MONITOR
1
STANDARD CAMERA
SOD14C
NORMAL TYPE CAMERA
2
PIR CAMERA
SMM-PIRCAM
PIR OBSERVATION CAMERA
1
Tapping Screw 2
CAMERA BRACKET
SBR-110
STAND TYPE BRACKET
2
Tapping Screw 3
MCB-60
6PIN SHIELD CABLE
2
60ft(1ft=0.3048m)
MCB-100
6PIN SHIELD CABLE
1
100ft(1ft=0.3048m)
INSTALLATION MANUAL
-
-
1
POWER CORD
-
-
1
VCR CABLE
-
-
1
SENSOR CONNECTOR
-
-
2
CAMERA CABLE
Q’ty
• Check whether all the following devices and accessories are included with the main system.
English-13
NOTE
1-3) CAMERA composition and installation method
1) Standard Camera composition (SOD14C)
PIN NUMBER
SPEC
!
SPEAKER(HOT)
@
VIDEO_OUT
#
GND
$
SPEAKER(COLD)
%
AUDIO_OUT/ALARM_OUT
^
12V DC
a. Lens
It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide
area.
b. Microphone
Capable of picking up all sound in the vicinity of the camera location and transmitting to
the monitor.
c. Camera fitting groove
Enables the camera to be fixed onto the bracket. You may install it either above or below
the camera if necessary.
d. 6-pin modular jack
Used to connect the camera to the monitor.
English-14
e. SENSOR jack
Used to connect the sensor to the camera.
f. Speaker
It outputs the sound signal which was transfered from the monitor.
•
PIN configuration of the DOME CAMERA is the same as the STANDARD
CAMERA.
•
But, DOME CAMERA does not provide ALARM JACK.
2) Installing Syandard Camera (SOD14C)
SOD14C s camera can be attached to the wall, ceiling or shelf using the camera mount bracket
(SBR-110).
Choose an installation site that can sufficiently support the weight of the equipments to be installed.
Attach the camera mount bracket to the wall or ceiling using the supplied three screws (M4 X L15).
Adjust the camera to target the video location and tighten the bracket handle on the camera mount
bracket.
4x15 sized screws
wall or ceiling
English-15
3) PIR Camera composition
(Top)
(Bottom)
3
5
4
1
2
① Lens
It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide
area.
➁ Speaker
It outputs the sound signal which was transfered from the monitor.
➂ Fresnel Lens
An infrared focusing lens for increasing the sensitivity of the built-in PIR sensor.
English-16
➃ 6-pin modular jack
Used to connect the camera to the monitor.
PIN NUMBER
SPEC
!
SPEAKER(HOT)
@
VIDEO_OUT
#
GND
$
SPEAKER(COLD)
%
AUDIO_OUT/ALARM_OUT
^
12V DC
⑤ 5-Pin Terminal Block
A terminal block for supplying backup power for the PIR sensor operation during power
outages and for transmitting the relay signals to external devices during the PIR sensor
operation.
PIN
SPEC
!
Power Input
@
(Back Up)
#
5
4
3
2
1
DC 12 Volts
Ground
Not Used
$
Relay Output
COM
%
(350V 130mA)
N.C
English-17
(Sensor Detection Angle & Area)
1) Vertical View Pattern
2) Horizontal View Pattern
English-18
(Inside)
6
8
7
9
➅ Function Switch
A function switch for the PIR sensor operation.
PIN
ON
!
OFF
S1
!
S2
@
S3
#
S4
$
Function
@
Sensor Sensitivity
On, On : Low
On, Off : Normal
Off, On : Normal
Off, Off : High
#
Alarm Led On/Off (Sensor On)
$
Sensor On/Off
⑦ PIR Sensor
A thermal heat sensor that detects infrared radiation projected by warm objects.
⑧ Microphone
Capable of picking up all sound in the vicinity of the camera location and transmitting to
the monitor.
⑨ Electronic Relay
Output power is 350V/130mA.
English-19
Camera installation Hints
1. Do not install directly towards rising or setting sun. Can cause burn or damage to internal options.
2. Do not limit desired detection zone by interference of curtains, screens, potted plants, etc.
3. Also, do not locate it in front of source of water/oil vapors. Avoid placement of heat source inside
detection zone
4. Do not install outdoors.
English-20
4) Installing the PIR Camera (SMM-PIRCAM)
1. Choose an installation site that can sufficiently support 5 times the weight of the equipments to be
installed.
2. Remove the screw (BH M2.6) at the bottom of the main unit by turning it counterclockwise, and
then lift the assy-case front as you push it upward to detach it from the case-rear.
(❊ Do not apply excessive force, as doing so may damage the inside assembly.❊)
Assy-case front
Screw (BH M2.6)
CASE-REAR
3. Place the case-rear over the installation site and mark screw holes with a pencil (indicated by the
circles in the illustration). Drill a pilot hole for each pencil mark (5mm in diameter and at least
35mm in depth), and then fully insert the supplied plastic anchors (HUD 5) into them.
English-21
4. Connect the Camera connector(RJ-11) cable to the case-rear as well as the cable to be connected to
the terminal.
5. Align the two holes of the case-rear to the holes of the plastic anchors, and then fasten the
screw-tappings (BH M3 X 30).
SCREW-TAPPING
G(BH M3 x 30)
SCREW-TAPPING
G(BH M3 x 30)
English-22
6. Adjust the direction of the lens.
1) Use the cross (+) screw driver to turn the screw (indicated by the arrow in the illustration)
counterclockwise slightly. The lens body will move.
2) Tilt the lens body down about 10° from the horizontal, and then turn the screw clockwise to fasten it.
Screw (HB M4 x L8)
7. Assemble the assy-case front onto the case-rear as shown in the illustration. Fasten the assy-case
front to the case-rear with the screw (BH M2.6) you removed earlier.
CASE-REAR
ASSY-CASE FRONT
Screw (BH M2.6)
English-23
4) Camera Mount Bracket(SBR-110) & Standard Camera(SOD14C)
(1) Overview
CAMERA MOUNT BRACKET (SBR-110) is used to attach the camera to a wall, ceiling or shelf.
(2) Installation
Explains the installation of CAMERA MOUNT BRACKET as wall as the installation of the camera
onto the CAMERA MOUNT BRACKET.
•
Choose an installation site that can sufficiently support the weight of the equipments to be
installed.
•
Attach the camera mount bracket to the wall using the supplied screws (M4 X L15).
•
Adjust the camera to target the video location and tighten the bracket handle on the camera
mount bracket. Install the camera on to the male screw of the Camera Mount Bracket by
rotating the camera in clockwise.
English-24
•
Loosen the handle by turning it in a counter clockwise direction and then adjust the camera
position . Tighten the handle, turning it clockwise, and lock the camera in position.
•
Connect the camera cable to the camera.
Handle
(3) Specifications
Use : Indoor
Installation : Wall or Ceiling
Dimensions : 57 (W) X 47.2(H) X 100.5(L)
Weight : 150g
Operating Temperature : -10°C ~ 50°C
(4) Accessories
SCREW (M3 X L16) : 3 pcs
English-25
1-4) CAMERA Composition and Connecting Method to
MONITOR
After positioning monitor and installing four cameras to a desired location, please connect CAMERA to
MONITOR through CAMERA CABLE (MCB-60) as shown in the below figure. Please check whether
or not it is properly connected.
Connection status checking method :
•
Turn on the monitor after connecting cameras, and check if camera image is displayed.
•
In case monitor and camera is not connected, OSD ‘L’(LOSS) will be displayed on blue
The initial screen mode of monitor is quad mode.
screen.
English-26
1-5) External terminal connecting method for CAMERA and
MONITOR
1) External terminal connecting method for CAMERA
•
An additional PIR sensor or external sensor can also be connected.
•
The additional PIR sensor can be connected as shown in the above graphic.
•
Sensor’s trigger signal is NO (Normal Open).
•
Sensor is not supplied. (Sold separately)
2) VIDEO OUT BNC (1~4) terminals connecting method of monitor rear
VIDEO OUT BNC1 ~ BNC4 terminals in the rear of the monitor are VIDEO terminals for outputting
video images from OBSEVATION CAMERA to THROUGH OUT.
BNC VIDEO output terminal can be used to connect to VCR (TIME LAPSE) or SLAVE MONITOR.
3) VCR or ALARM terminal connecting method
TIME LAPSE VCR
OR NORMAL VCR
VIDEO IN
VIDEO OUT
AUDIO IN
AUDIO OUT
NOT USED
VIDEO OUT
VIDEO IN
AUDIO OUT
AUDIO IN
a) Connect the 6-pin plug to the VCR terminal on the real panel.
b) Connect the VIDEO OUT plug to the VIDEO IN terminal of the VCR.
c) Connect the VIDEO IN plug to the VIDEO OUT terminal of the VCR.
d) Connect the AUDIO OUT plug to the AUDIO IN terminal of the VCR.
e) Connect the AUDIO IN plug to the AUDIO OUT terminal of the VCR.
English-27
f) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR.
g) Connect the A/O (COLD) terminal on the rear panel to the Ground terminal of the VCR.
h) Connect the A/R terminal on the rear panel to the Alarm Reset terminal of the VCR.
i) Connect the G (ground) terminal on the rear panel to the Ground terminal of the VCR.
1-6) Whole System connection and configuration
or
VCR
SHARP
TINT
COLOR
BRIGH
TCON
TRAST
VOLUM
E
VIDEO
A
B
DATA
C
SLAVE
MONITOR
VCR (TIME LAPSE) REAR
English-28
Chapter 2: MONITOR FRONT PANEL KEY
Function and Using Method
Front Panel
2-1) TALK KEY
TALK KEY allows users to transmit voice signal to intended camera by inputting voice with built-in
√
MIC in the front of the monitor. For this function, select a target camera with the œENTER√
SWITCH on the FRONT PANEL, and press AUD/SP SEL KEY. At this time, if a voice signal is
generated through the MIC with the TALK KEY pressed, the signal will be transmitted to the camera.
2-2) AUD/SP SEL KEY
AUD/SP SEL KEY allows users to select a camera to exchange voice signals with the monitor at
QUAD DISPLAY MODE. At QUAD DISPLAY MODE, select target camera display by turning
œENTER√
√ SWITCH left or right, and press AUD/SP SEL KEY. Then “S” OSD will be displayed
on the selected screen. If you want to exchange voice signals with another camera, turn again the
œENTER√
√ SWITCH again to select the camera display, and press AUD/SEL KEY. Then, “SP” OSD
will be displayed and users can exchange voice signals with the monitor.
2-3) VOL+/VOL- KEY
Allows users to decrease or increase voice signal generated from the monitor.
VOL+ : Increase sound volume from the monitor.
VOL- : Decrease sound volume from the monitor.
English-29
2-4) POWER SAVE- KEY
Allows users to set POWER SAVE MODE of monitor. PICTURE screen is off when the POWER
SAVE KEY is pressed, and the ON/OFF status of the monitor can be judged through LED ON/OFF
status. Users can exit from POWER SAVE MODE by pressing POWER SAVE BUTTON again under
picture “OFF” status. POWER SAVE MODE is automatically cancelled and picture is “ON” when an
event such as an alarm or loss at POWER SAVE MODE occurs.
2-5) ALARM RESET- KEY
Alarm function can be cancelled while the alarm is working.
2-6) QUAD/PAGE- KEY
Allows users to display QUAD-A or QUAD-B at QUAD DISPLAY MODE.
•
QUAD-A: QUAD DISPLAY MODE from Camera 1 to Camera 4
•
QUAD-B: QUAD DISPLAY MODE from Camera 5 to Camera 8
2-7) LIVE/VCR- KEY
Allows users to switch LIVE MODE to VCR MODE or VCR MODE to LIVE MODE. If VCR MODE
is cancelled, the QUAD picture of LIVE MODE will be automatically displayed. In case any event
happens at VCR MODE such as LOSS or ALARM, the MODE will be automatically switched to LIVE
MODE, and the pre-set operation for the event will be carried out. If there is no external input at VCR
MODE, the OSD “NO SIGNAL” will be displayed.
•
LIVE MODE: Image and voice signal from CAMERA is displayed.
•
VCR MODE: External image and voice signal from VCR terminal from the rear of the monitor is
displayed.
English-30
2-8) PIP- KEY
Can be used to see the main screen while Single screen is displayed. The main screen can be changed
and transfered to another channel while PIP is working. Please refer to "CHAPTER 4. DISPLAY
MODE SETTING" for PIP function and details.
2-9) FREEZE- KEY
This key allows users to see a target camera picture at PAUSE MODE. If users select the camera with
√ KEY, and press the FREEZE BUTTON, the OSD “F” will be displayed on pause
the œENTER√
picture from the camera. Other FRONT KEY input is ignored at FREEZE MODE, and other FRONT
KEY inputs will be available only after the FREEZE MODE is cancelled.
2-10) SEQUENCE- KEY
It makes a picture switch sequentially. This means that display the picture will be displayed during the
DWELL TIME pre-set at the DWELL MENU of SETUP MENU, and switch the picture automatically
as a pre-set sequence. Please refer to Chapter 3. DWELL TIME MENU function and setting method for
details of DWELL TIME setting.
2-11) ZOOM- KEY
It zooms a part of a picture doubling it in the display. If the ZOOM BUTTON is pressed, zoom area
√ SWITCH left and right at
will be displayed. Users can move to a target area by turning œENTER√
√ SWITCH is pressed at the target area, the area will be displayed with 2 times
this time. If œENTER√
larger.
2-12) POWER- KEY
It turns ON/OFF the power of the monitor and camera at the same time.
In case the monitor power is ON, LED of monitor front is lit.
English-31
2-13) ENTER- KEY
√ key, it allows users to 1. enter SET UP MENU movement and
As a multi functional œENTER√
SETTING MODE and set data, and 2. display single camera picture.
Please refer to the below picture.
•
œENTER√
√ SWITCH using method at MENU setting
Used to change data
value after moving to
target menu and entering
setting mode by turning
switch left or right.
•
Used to enter target
setting mode by
pressing switch.
SINGLE DISPLAY MODE Entering and Function
√
At QUAD DISPLAY or SEQUENTIAL SWITCHING MODE, pressing the œENTER√
SWITCH allows users to enter the SINGLE DISPLAY MODE to see the image of one selected
camera at full screen. Users can move to another camera image by the ENTER SWITCH turning
left and right.
2-14) MENU- KEY
It allows users to enter SETUP MENU, and set the following items on the SETUP MENU.
•
ADJUST : Screen adjustment
•
DATE/TIME MENU : Setting of Date/Time format and time to be displayed
•
DWELL MENU : Setting of DWELL TIME at SEQUENTIAL SWITCHING MODE
•
DISPLAY MENU : Setting DISPLAY MODE
•
TITLE MENU : Setting camera name
•
ALARM MENU : Setting ALARM and BUZZER
•
VIEW EVENT LOG MENU : Allows users to see EVENT (ALARM, LOSS) list per time,
camera
Please refer to the following Chapter 3 for setting method and function of SETUP MENU per item.
English-32
Chapter 3: Setting each item function at SETUP
MENU
Pressing the MENU BUTTON of the FRONT PANEL allows users to enter SETUP MENU and see the
following menu OSD box. Setting method of each SETUP MENU function and operation is as follows.
06/01/03
SETUP
13:14:00
MENU
1. ADJUST
2. DATE/TIME
3. DWELL TIME
4. DISPLAY
5. TITLE
6. ALARM
7. VIEW EVENT LOG
3-1) ADJUST MENU function and setting method
•
Function: Allows adjustment to the display status
•
√ SWITCH and press the
Setting method: Move to #1. ADJUST MENU by using œENTER√
ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial
setting status.)
06/01/03
ADJUST
13:14:00
SETTING
CONTRAST
BRIGHT
COLOR
SHARPNESS
TINT
50
50
50
50
50
√ SWITCH left or right.
Move to a target item by turning œENTER√
√ SWITCH.
Enter the item by pressing the œENTER√
√ SWITCH left or right
At this time, set a target value by turning œENTER√
You can move to another item by pressing again the SWITCH after setting the target value.
(1) CONTRAST : Adjusts light and shade of screen
(2) BRIGHT : Adjusts lightness of entire screen
(3) COLOR : Adjusts color density
(4) TINT : Adjusts color sense
(5) SHARPNESS : Adjusts contour of screen
English-33
3-2) DATE/TIME MENU Function setting
•
Function: Sets the display date format and current time.
•
√ SWITCH at setup menu,
Setting method :Move to #2. DATE/TIME MENU by using œENTER√
then press the ENTER SWITCH to display the OSD as shown in the below figure.
(The figure shows the initial setting status.)
06/01/03
DATE/TIME SETTING
DATE TYPE
DATE
TIME [HH:MM:SS]
•
13:14:00
MM/DD/YY
06 / 01 / 03
13 : 14 : 00
Setting method of date display format
√ SWITCH, and enter the mode for setting date
Move to the format item by turning œENTER√
format by pressing the ENTER SWITCH.
At this time, select a target date format by turning left and right the SWITCH.
(“YY/MM/DD”, “MM/DD/YY”, “DD/MM/YY” are available for selectable data format.)
•
Date and current time setting method
Repeat the above instruction for moving to each item (MONTH, DAY, YEAR, HOUR, MINUTE,
SECOND) and entering the mode. Current date and time to display can be set. (It can be referred
when ALARM or LOSS occurs.)
3-3) DWELL TIME MENU function setting
•
Function : Displays each picture for pre-set time and automatically switches it to the next picture
•
√ SWITCH at SETUP
Setting method : Move to #3. DWELL TIME menu by using œENTER√
at SEQUENTIAL DISPLAY MODE.
MENU, and press the ENTER SWITCH to display the following OSD as shown
in the below figure. (The figure shows the initial setting status.)
06/01/03
DWELL TIME SETTING
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8
QUAD-A
QUAD-B
13:14:00
01 SEC
01 SEC
01 SEC
01 SEC
01 SEC
01 SEC
01 SEC
01 SEC
01 SEC
01 SEC
√ SWITCH, each camera picture will be
If the time is set for each camera channel by using œENTER√
displayed for the set time and switched to the next picture automatically.
English-34
3-4) DISPLAY MENU function setting
•
Function: Allows users to select the color and ON/OFF of borderline at QUAD DISPLAY.
•
√ SWITCH at
Setting method: Move to #4. DISPLAY SETTING MENU by using œENTER√
SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure below.
(The figure shows the initial setting status.)
06/01/03
DISPLAY
13:14:00
SETTING
BORDER
BORDER COLOR
PIP POSITION
ON
BLACK
T-LEFT
√ SWITCH, and change the set value.
Move to each item by using œENTER√
1) BORDER item determines whether or not boarder line is displayed at QUAD DISPLAY MODE.
(ON: Displays the boarder line, OFF: Does not display the boarder line)
2) BORDER COLOR item sets boarder line color among three colors: Black, White, Gray.
3) PIP POSITION item sets the location of sub picture at PIP DISPLAY. (T-LEFT: Upper part of left
side, T-RIGHT: Upper part of right side, B-LEFT: Lower part of left side, B-RIGHT: Lower part of
right side)
English-35
3-5) TITLE MENU Function setting
•
Function: Set the title of each camera at your discretion.
•
√ SWITCH at SETUP MENU,
Setting method: Move to #5. TITLE MENU by using œENTER√
and press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure
shows the initial setting status.)
06/01/03
TITLE
CAMERA1
CAMERA2
CAMERA3
CAMERA4
CAMERA5
CAMERA6
CAMERA7
CAMERA8
13:14:00
SETTING
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8
0 1 2 3 4 5 6 7 8 9 : = . ( )
A B C D E F G H I J K L M N O P Q
R S T U V W X Y Z [ / ] _ ~ ← + −
√ SWITCH then press the ENTER KEY to
Move to a target camera channel by using œENTER√
display a cursor at the space of the first character of camera title. Move the cursor to a target character
√ SWITCH left or right, then press the
in OSD box of lower part by turning left and right œENTER√
ENTER KEY to set the character. The cursor automatically moves to the next space for a new character
after one character is set. Set the title of camera by repeating the same method.
(Only eight characters are available for a camera title.)
English-36
3-6) ALARM MENU Function setting
•
Function: Allows users to set the ALARM MODE for each camera.
•
√ SWITCH at SETUP
Setting method: Move to #6. ALARM MENU by using œENTER√
MENU, and press the ENTER SWITCH to display the OSD as shown in the
figure below. (The figure shows the initial setting status.)
06/01/03
ALARM
13:14:00
SETTING
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8
HOLD TIME
ALARM ON TIME
ALARM OFF TIME
BUZZER
ON
ON
ON
ON
ON
ON
ON
ON
05SEC
00:00
00:00
ON
(1) CAM1 to CAM8 item sets whether the alarm sensor connected to the camera is used or not.
(ON: Alarm function setting, OFF: Alarm function canceling)
(2) HOLD TIME item sets time to freeze alarm operation when alarm occuring.
(HOLD TIME to be set: 05SEC ~ 1MIN ~ 30MIN)
(3) ALARM ON/OFF TIME item sets beginning time (ON) and end time (OFF) that monitor
recognizes alarm operation as alarm event.
* Note :Even if CAMERA ALARM is set to ON, alarm operation is not carried at time band except
pre-set ALARM ON/OFF TIME.
(4) BUZZER item sets whether or not buzzer device set in monitor is used at an ALARM or LOSS
occurring.
(ON: Buzzer operation, OFF: NA)
English-37
3-7) VIEW EVENT LOG MENU function and setting method
•
Function: Displays the time and date of camera event and type of event.
•
√ SWITCH at
Setting method: Move to #7. VIEW EVENT LOG MENU by using œENTER√
SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in
the figure below. (The figure shows the initial setting status.)
06/01/03
Sequence of
event happening
Camera No.
that event
happened.
13:14:00
NO
CH
MM/DD/YY
HH:MM:SS
01
02
03
04
05
06
07
08
07
01
01
02
01
01
01
01
02/10/03
02/11/03
06/01/03
06/01/03
--/--/---/--/---/--/---/--/--
10:00:30
11:22:00
12:33:01
13:01:03
--:--:---:--:---:--:---:--:--
EVT
A
L
-
Type of event happening
L : LOSS
A : ALARM
Time of event
happening
Date of event
happening
An event which occurred most recently is recorded with first priority, then users can move to the next
√ SWITCH. A Total of 64 events can be listed.
page by using œENTER√
* Note :IF you press the FREEZE key and the SEQUENCE key at the same time, all event lists will be
erased.
English-38
Chapter 4: DISPLAY MODE setting method
4-1) SINGLE SCREEN DISPLAY
Initial display mode of monitor is QUAD-A. In case users want to see the camera image at full mode,
√ SWITCH left and right. After that, press the ENTER
select a target camera by turning œENTER√
√
SWITCH and selected camera image will be displayed at full screen. If users turn the œENTER√
SWITCH left / right at SINGLE DISPLAY MODE at this time, they can see another camera image at
full screen. For example, when users want to see CH1 at FULL MODE after SINGLE -displaying CH2
at QUAD-A, please follow the instructions below.
06/01/03
13:14:00
CH1
CH2
CH3
CH4
06/01/03
➯
13:14:00
CH1
CH2
CH1
CH2
QUAD-A
QUAD-A
√ SWITCH
Select CH2 by turning œENTER√
INITIAL DISPLAY STATUS
➯
√
Press œENTER√
SWITCH after
selecting CH2
06/01/03
13:14:00
06/01/03
13:14:00
➯
CH1
Display CH1
by turning
œENTER√
√
SWITCH
FULL SCREEN DISPLAY of CH1
CH2
FULL SCREEN DISPLAY of CH2
English-39
4-2) QUAD MODE DISPLAY
Users can switch SINGLE DISPLAY MODE and SEQUENTIAL DISPLAY MODE to QUAD
DISPLAY MODE, or QUAD-A (QUAD-B) to QUAD-B (QUAD-A), or PIP MODE to QUAD MODE,
press the QUAD/PAGE KEY.
* At QUAD MODE display from SINGLE MODE or SEQUENCE MODE,
06/01/03
13:14:00
06/01/03
➯
CH1
CH2
CH3
CH4
Press
QUAD/PAGE
KEY
CH3
CH3 DISPLAY
13:14:00
QUAD-A
QUAD MODE DISPLAY
of QUAD-A
* At QUAD-B(QUAD-A) display from QUAD-A(QUAD-B),
06/01/03
13:14:00
CH1
CH2
CH3
CH4
06/01/03
➯
CH5
CH6
CH7
CH8
Press
QUAD/PAGE
KEY
QUAD-A
QUAD MODE DISPLAY
of QUAD-A
13:14:00
QUAD-B
QUAD MODE DISPLAY of
QUAD-B
* At QUAD-B(QUAD-A) display from PIP MODE,
06/01/03
13:14:00
06/01/03
➯
CH 3
CH 1
Press
QUAD/PAGE
KEY
PIP MODE DISPLAY
13:14:00
CH5
CH6
CH7
CH8
QUAD-A
QUAD MODE DISPLAY of
QUAD-A
English-40
4-3) AUTO SEQUENTIAL DISPLAY MODE
Pressing on the SEQUENCE KEY on the front allows screen to automatically switch to SINGLE
MODE full screen or QUAD MODE. (‘no-signal’ channels will be skipped while single screen is
auto-switching.)
If the DWELL TIME SETTING of SETUP MENU is set to 3 seconds and the SEQUENCE KEY is
pressed at this time, the operation will be carried out as follows.
* SINGLE MODE SEQUENCE DISPLAY
06/01/03
13:14:00
06/01/03
13:14:00
➯
In 3 seconds
CH 2
CH 3
Press SEQUENCE KEY
when CH2 is displayed
at full screen
Automatic sequential switching to CH3
➯
In 3 seconds
06/01/03
13:14:00
06/01/03
13:14:00
➯
In 3 seconds
CH 1
CH 4
Automatic sequential switching to CH1
Automatic sequential switching to CH4
* QUAD MODE SEQUENCE DISPLAY
06/01/03
13:14:00
CH1
CH2
CH3
CH4
QUAD-A
06/01/03
➯
06/01/03
13:14:00
CH5
CH6
CH7
CH8
QUAD-B
English-41
➯
13:14:00
CH1
CH2
CH3
CH4
QUAD-A
4-4) PIP MODE DISPLAY
Can be used to see PIP screen in Single screen mode.
√ on PIP screen ,the main screen will change. If you press the œENTER√
√
If you press the œENTER√
to the left and right,the main screen can be transferred to another channel. Sub-screen location can be
selected on DISPLAY MENU in SETUP MENU.
06/01/03
13:14:00
06/01/03
13:14:00
➯
CH1
CH3
Press
œENTER√
√
KEY
Under PIP DISPLAY
06/01/03
CH3
CH1
Main and Sub screen is switched
13:14:00
06/01/03
13:14:00
➯
CH1
CH3
√
Turn œENTER√
SWITCH right
Under PIP DISPLAY
06/01/03
CH2
CH3
Main screen is switched
13:14:00
06/01/03
13:14:00
➯
Press PIP KEY
CH2
CH1
Under single screen display
CH3
Main and Sub screen is displayed
as set at the DISPLAY MENU of
SETUP MENU
English-42
4-5) ZOOM MODE DISPLAY
When users want to see zoomed image of a specific area of the display, press the ZOOM KEY in the
√ SWITCH left and
front to display zoom selection area. Select zoom target area by turning œENTER√
right, and press the ENTER SWITCH, then, the selected area will be displayed at full single mode with
zoomed area doubled. At zoom function operation at SINGLE DISPLAY MODE (CH2), the operation
will be carried out as shown in figure below. (Zoom selection areas at SINGLE DISPLAY MODE are
nine.)
06/01/03
13:14:00
06/01/03
13:14:00
➯
Press ZOOM
KEY
CH2
CH2 SINGLE DISPLAY
CH2
ZOOM area is activated.
➯
06/01/03
13:14:00
06/01/03
13:14:00
➯
Press
œENTER√
√
SWITCH
The selected area will be doubled
and at FULL DISPLAY.
CH2
√ SWITCH and
Turn œENTER√
move to desired location
English-43
Chapter 5: Each product feature
SOD14C : Standard Camera
Model Name
SOD14C
Broadcasting System
NTSC STANDARD
Imaging Device
1/4 ”SUPER HAD IT CCD
Effective Pixels S
510(H) x 492(V)
Synchronization
Internal
Resolution
H :330 TV Lines, V: 350 TV Lines
Signal Output
VBS 1.0Vp-p(75ohms composite)
S/N Ratio
≤ 48 dB
Minimum Scene Illumination
2lux(F2.0, 50 IRE)
Gamma Correction
0.45
Lens
Focal Length (f) : 3.8mm, Aperture Ratio (F) : 2.0
Auto Exposure
Electronic Shutter lris
Audio
-40dB Condenser Microphone Inclusion
I/O Connectors
Modular jack
Operating Temperature
-10 ~ +50 °CC
Power Source
DC 12V
Power Consumption
Approx. 2W
Dimensions
57(W) x 47.2(H) x 100.5(L)
Weight
150g
English-44
SMM-PIRCAM : PIR Camera
Model Name
SMM-PIRCAM
Broadcasting System
SMM-PIRCAM
: NTSC Standard
Imaging Device
SMM-PIRCAM
: 1/4'' Color IT CCD
Effective Pixels
537(H) X 505(V)
Synchronization
Internal
Resolution
SMM-PIRCAM
Signal Output
VBS 1.0Vp-p(75ohms composite)
S/N Ratio
≤ 48 dB
Minimum Scene Illumination
SMM-PIRCAM
Gamma Correction
0.45
Lens
Focal Length : 3.8mm, F Number : 2.0
Auto Exposure
Electronic Shutter lris
PIR Sensor
: 330 TV Lines(H), 350 TV Lines(V)
: 2 lux(F2.0, 50 IRE)
Warm-Up Period
:Max. 50 seconds
Spectral Response
: 5 to 14 um
Sensitivity
: 4860(V/W)
Detectivity
: 1.5 x 108cm Hz 2/1/W
Sensor
: Off/On
Alarm LED
: Off/On (0.5 to 1 second)
Alarm Output
: NC (350V/130mA)
Audio
-40 dB Condenser Microphone Inclusion
I/O Connectors
Modular jack (RJ-11)
Operating Temperature
-10 ~ +50 °C
Power Source
DC 12V (Camera & Sensor from Monitor)
DC 12V (Sensor Only from External Power Supply)
English-45
OBSERVATION MONITOR
Video Input
• CAMERA 8 Input: 1.0Vp-p(CVBS), 75Ω (vertical),
• VCR 1 Input (to Video Out of VCR) : 1.0Vp-p, 75Ω (vertical),
Video Output
• BNC 4 Output: 1.0 Vp-p, 75Ω (vertical), S-Jack Type, CVBS
• VCR 1 Output: 1.0 Vp-p, 75Ω (vertical), S-Jack Type, CVBS
Voice Input
• CAMERA 8 Input:
• VCR 1 Input (to Audio Out of VCR) : S-Jack Type
Voice Output
• CAMERA 8 Input:
• VCR 1 Output: S-Jack Type
Alarm/Motion Features:
A/O (HOT, COLD) : Relay Active
Connected to Alarm
A/R (Alarm Reset) : Open Collector “L” Level,
Pulse Width =150ms or above
Box/Camera
Alarm Hold Time : Select 5 sec, 15 sec, 30 sec, 1 min, 3 min,
5 min, 10 min, 20 min, 30 min..
Sequence
Select between 01 sec to 30 sec.
Event List
(max) 64 case
Display mode
Single mode, Quad-A mode, Quad-B mode, PIP, Sequence
Freeze, Zoom(X2)
Horizontal Resolution
350 TV Lines or more (Live Mode Full Screen)
Operation Temperature
0 °C ~ 40 °C
CRT
SSC-21DQ : 21" FLAT CRT, SSC-15DQ : 15" FLAT CRT
Dimension (W x D x H (mm))
21" : (MONITOR)520 X 509 X 486, (PACKING)655 X 640 X 771
15" : (MONITOR)388 X 459 X 379, (PACKING)462 X 543 X 613
Weight
21" : (MONITOR) 28.0Kg, (PACKING) 39.5Kg
15" : (MONITOR) 15.2Kg, (PACKING) 22Kg
Power consumption
110W
Video system
NTSC VIDEO SYSTEM
High Voltage (KV)
28 ±2.0
Operation Humidity Range
0~90%
AC Input Ranges
AC 120V, 60Hz
Audio Output[watt]
1.5W
English-46
Memo
English-47
IMPORTADO POR
SAMSUNG ELECTRONICS MEXICO. S.A.DE C.V.
Saturno No. 44, Col. Nueva Industrial Vallejo
Gustavo A. Madero C.P. 07700, Mexico D.F. Mexico
TEL) 52-55-5747-5100
EXPORTADO POR
Samsung Electronics Co., Ltd.
416, Mae tan-3dong, Yeongtong-Gu,
Suwon City, Kyungki-Do Korea
Part No.: AA68-03537A-00
Printed in Korea