Sharp EL-1607P Specifications

This key is used to print out numbers not
subjects to calculation such as code, date, etc.
Subtotal –Used to get subtotal(s) of additions and/or
or
subtractions. When pressed following the
key, the subtotal is printed with the symbol
“◊” and the calculation may be continued.
By pressing this key even in the Non-print mode, the
displayed number is printed without any symbol.
ELECTRONIC PRINTING CALCULATOR
EL-1607P
OPERATION MANUAL
CONVERSION KEY:
Fig. 1
This key is used:
• to store the conversion rate.
• obtains a value by multiplying a given number with a
specified conversion rate.
• to recall the presently stored rate for check. Press
first to clear the calculation register and reset an
error condition, then press
. The conversion rate is
printed with the symbol “∆”.
CONVERSION KEY:
This key is used to obtain a value by dividing a given
number with a specified conversion rate.
Fig. 2
DISPLAY SYMBOLS:
M
–
E
•
PRINTED IN CHINA
12DT(TINSE1648EHZZ)
:
:
:
:
A number has been stored in memory.
The display value is negative.
Error or overflow of capacity.
Appears when a number is in the grand total memory.
Fig. 3
INK ROLLER REPLACEMENT
If printing is blurry even when the ink roller is in the proper
position, replace the roller.
DO NOT PULL PAPER BACKWARDS AS THIS MAY
CAUSE DAMAGE TO PRINTING MECHANISM.
Ink roller: Type EA-772R
OPERATIONAL NOTES
To insure trouble-free operation of your SHARP calculator, we
recommend the following:
1. The calculator should be kept in areas free from extreme
temperature changes, moisture, and dust.
2. A soft, dry cloth should be used to clean the calculator. Do
not use solvents or a wet cloth.
3. Since this product is not waterproof, do not use it or store it
where fluids, for example water, can splash onto it.
Raindrops, water spray, juice, coffee, steam, perspiration,
etc. will also cause malfunction.
4. If service should be required, use only a SHARP servicing
dealer, a SHARP approved service facility or SHARP repair
service.
5. Do not wind the AC cord around the body or otherwise
forcibly bend or twist it.
6. Unplug the calculator by pulling on the plug portion, not the
cord.
7. Do not place objects on the AC cord. Do not run the AC cord
under rugs, mats, or other such objects.
8. This product, including accessories, may change due to
upgrading without prior notice.
SHARP will not be liable nor responsible for any incidental or
consequential economic or property damage caused by
misuse and/or malfunctions of this product and its
peripherals, unless such liability is acknowledged by law.
OPERATING CONTROLS
POWER SWITCH; PRINT / ITEM
COUNT MODE SELECTOR:
“OFF”:
“•”:
“P”:
“P•IC”:
Note:
Power off.
Power ON. Set to the non-print mode.
Power ON. Set to the print mode.
Power ON. Set to the print and item count mode.
For addition or subtraction, each time
is pressed, 1 is
is pressed,
added to the item counter, and each time
1 is subtracted.
• The count is printed when the calculated result is
obtained.
• Pressing of
,
,
or
clears the counter.
The counter has a maximum capacity of 3 digits (up to
±999). If the count exceeds the maximum, the counter
will recount from zero.
Use of
,
and
will automatically override the Add mode
and decimally correct answers will be printed at the preset decimal
position.
ROUNDING SELECTOR:
“ ”:
“5/4”:
“ ”:
Note:
An answer is rounded up.
An answer is rounded off.
An answer is rounded down.
The decimal point floats during successive calculation by
or
.
the use of
If the decimal selector is set to “F” then the answer is always
rounded down ( ).
DECIMAL SELECTOR:
CONSTANT/ADD MODE SELECTOR:
This key is used to store the conversion rate or the tax/
discount rate.
Page 1
Also, in rare cases, printing may stop midway and the indication
“E” appear on the display. This is not a malfunction but is
caused when the calculator is exposed to strong
electromagnetic noise or static electricity from an external
source. Should this occur, press the
key and then repeat the
calculation from the beginning.
• Enter the conversion rate, then press
.
• A maximum of 6 digits can be stored (decimal point is not
counted as a digit).
SPECIFICATIONS
Tax/discount rate:
Operating capacity: 12 digits
Power source: AC: 230V-240V, 50Hz
• Enter the adding tax rate, then press
.
before pressing
• To store a discount rate, press
.
• A maximum of 4 digits can be stored (decimal point is not
counted as a digit).
Note: • For the conversion rate and the tax/discount rate, a
single value can be stored for each. If you enter a new
rate, the previous rate will be cleared.
• The stored values for the conversion rate and the tax/
discount rate will be cleared if the power cable is
disconnected.
Fig. 2
PAPER FEED KEY
LAST DIGIT CORRECTION KEY
Fig. 3
GRAND TOTAL KEY
CLEAR ENTRY KEY
TOTAL KEY
Cleaning the printing mechanism
MULTIPLICATION KEY
If the print becomes dull after long time usage, clean the
printing wheel according to the following procedures:
DIVISION KEY
PLUS EQUAL KEY
CHANGE SIGN KEY
MARKUP KEY
MEMORY SUBTOTAL RECALL KEY
EL-1607P(AB1)
Fig. 1
Conversion rate:
MEMORY TOTAL CLEAR KEY
The calculator will automatically remember the second number
entered (the divisor) and
instruction.
‘‘•’’: Neutral
‘‘A’’: Use of the Add mode permits addition and subtraction of
numbers without an entry of the decimal point. When the
Add mode is activated, the decimal point is automatically
positioned according to the decimal selector setting.
must be used
If an ‘‘0•E’’ is displayed at the time of the error,
to clear the calculator. If an ‘‘E’’ with any numerals except zero is
or
and the
displayed, the error may be cleared with
calculation can still be continued.
1. Entry of more than 12 digits or 11 decimals. This error can be
cleared with
or
.
2. When the integer portion of an answer exceeds 12 digits.
3. When the integer portion of the contents of the memory or
grand total memory exceeds 12 digits.
(Ex.
999999999999
1
)
4. When any number is divided by zero.
0
)
(Ex. 5
STORE KEY:
Multiplication:
Division:
ERRORS
There are several situations which will cause an overflow or an
error condition. When this occurs, “E” will be displayed. The
contents of the memory at the time of the error are retained.
Error conditions:
GRAND TOTAL MODE SELECTOR:
‘‘K’’: The following constant functions will be performed:
The calculator will automatically remember the first number
entered (the multiplicand) and
instruction.
1) Set the power switch to OFF.
2) Remove the printer cover. (Fig. 1)
3) Hold the top of the ink roller and remove the roller by pulling it
toward you and then upward. (Fig. 2)
4) Install the new ink roller in the correct position. Make sure
that the roller is securely in place. (Fig. 3)
5) Put back the printer cover.
“GT”: Grand Total
“•”: Neutral
MINUS EQUAL KEY
Presets the number of decimal places in the answer. In the ‘‘F’’
position, the answer is displayed in the floating decimal system.
WARNING
APPLYING INK TO WORN INK ROLLER OR USE OF
UNAPPROVED INK ROLLER MAY CAUSE SERIOUS
DAMAGE TO PRINTER.
TAX-INCLUDING KEY
PRE-TAX KEY
PERCENT KEY
NON-ADD/SUBTOTAL KEY:
Non-add –When this key is pressed right after an entry of a
number in the Print mode, the entry is printed on
the left-hand side with the symbol “#”.
1) Remove the printer cover and the ink roller.
2) Install the paper roll and feed it until it comes out of the front
of the printing mechanism.
3) Hold a small brush (like a tooth brush) lightly to the printing
wheel and clean it by pressing
.
4) Put back the ink roller and the printer cover.
Note: Do not rotate the printing mechanism manually, this may
damage the printer.
PRINTING SECTION
Printer: Mechanical printer
Printing speed: Approx. 2.5 lines/sec.
(At temperature 25°C (77°F), when
“741•9 +” is printed. The printing speed will vary with the
number of rows and the figure types to be printed.)
Printing paper:
57 mm(2-1/4") - 58 mm(2-9/32") wide
80 mm(3-5/32") in diameter (max.)
Operating temperature:
0°C – 40°C (32°F – 104°F)
Power consumption: 59 mA
Dimensions:
220 mm (W) × 303 mm (D) × 71.5 mm (H)
(8-21/32" (W) × 11-15/16" (D) × 2-13/16" (H))
Weight: Approx. 1.2 kg (2.65 Ib.)
Accessories:
1 paper roll, 1 ink roller (installed), and operation manual
WARNING
THE VOLTAGE USED MUST BE THE SAME AS SPECIFIED
ON THIS CALCULATOR. USING THIS CALCULATOR WITH
A HIGHER VOLTAGE THAN THAT WHICH IS SPECIFIED IS
DANGEROUS AND MAY RESULT IN A FIRE OR OTHER
TYPE OF ACCIDENT CAUSING DAMAGE. WE ARE NOT
RESPONSIBLE FOR ANY DAMAGE RESULTING FROM
USE OF THIS CALCULATOR WITH A VOLTAGE OTHER
THAN THAT WHICH IS SPECIFIED.
In case of abnormal conditions
PAPER ROLL REPLACEMENT
Never insert paper roll if torn. Doing so will cause paper to
jam.
Always cut leading edge with scissors first.
1) Insert the leading edge of the paper roll into the opening.
(Fig. 1)
2) Turn the power on and feed the paper by pressing
. (Fig. 2)
3) Lift the attached metal paper holder up and insert the paper
roll to the paper holder. (Fig. 3)
12.5.31, 6:17 PM
Adobe PageMaker 6.0J/PPC
When this unit is exposed to strong RF noise and/or extreme
physical shock during the operation, or when the power cord is
plugged into the AC outlet, the unit may start functioning
abnormally which, in some rare occasions, all keys - including the
power key and the
key - cease to respond.
If such abnormal conditions are observed, unplug the AC cord
from the socket. Keep the unit unplugged for about 5 seconds,
reconnect the AC plug, then turn on the power.
EL-1607P(AB1)-1➀
PERCENT CHANGE
CALCULATION EXAMPLES
1. Set the decimal selector as specified in each example.
The rounding selector should be in the ‘‘5/4’’ position unless otherwise specified.
2. The constant/add mode selector and grand total set mode selector should be in the “•” position (off) unless otherwise specified.
3. The print/item count mode selector should be in the ‘‘P’’ position unless otherwise specified.
4. If an error is made while entering a number, press
or
and enter the correct number.
ADDITION AND SUBTRACTION WITH ADD MODE
MIXED CALCULATION
• Calculate the dollar difference (a) and the percent change (b)
between two yearly sales figures $1,500 in one year and
$1,300 in the previous year.
1500
1,500.00
1300
200.00
12.45 + 16.24 + 19.35 – 5.21 =
(240 + 180 + 180 – 75) × 8 =
ITEM COUNT CALCULATION
Bill No.
Number of bills
Amount
1
1
$100.55
2
1
$200.00
3
1
$200.00
4
1
$400.55
5
1
$500.65
Total
(a)
1,500•00 +
1,300•00 –
200•00 ✱
(a)
15•38 %
(b)
(b)
15.38
Operation
Display
Print
Operation
Display
Print
240
240.
240• +
1245
12.45
12•45 +
180
420.
180• +
1624
28.69
16•24 +
600.
180• +
1935
48.04
19•35 +
525.
75
75• –
42.83
521
GRAND TOTAL
100 + 200 + 300 =
+) 500 – 600 + 700 =
Grand total
5•21 –
100•55 +
300.55
200•00 +
500.55
200•00 +
100.
100• +
400.55
901.10
400•55 +
525• ×
200
300.
200• +
500.65
1,401.75
8• =
4,200• ✱
300
600.
300• +
42•83 ✱
42.83
8
100.55
200
100
525• ◊
525.
100.55
*:
was not used in the entries.
003 • • • • • • • • • • • • •
600• ✱+
4,200.
500•65 +
005 • • • • • • • • • • • • •
(a)
1,401•75 ✱ (b)
1,401.75
600.•
CORRECTION OF ERRORS
62.35 × 11.11 =
123 + 556 → 123 + 456
62.35 × 22.22 =
700
600.•
700• +
11•11 =
692•71 ✱
692.71
123
123.
556
0.
456
579.
123• +
600.•
1,200• ✱✱
456• +
MEMORY
*
123,456.
46
12,345.
77.77
78
46.
78
1,234,578.
3,588.M
0•143✱
125.M
22•22 =
125
ADD-ON AND DISCOUNT
0•286✱
100
0.286
72
100• ×
100.
5
5•00
PERCENT
14,814.
125• ⴓ
25• +M ②
72.M
72• ×
8• =
576.M
Increase
EXAMPLE 3: Set the conversion rate (1 meter = 39.3701
inches).
39.3701
∆
576• –M ③
3,037• ◊M ④
39•3701 =
3,037.M
100 × 25% =
105•00 ✱ New amount
100• ×
100.
100
25
105.00
25•00 ✱
100• ×
100.
100
(123 ⴓ 1368) × 100 =
10
472.4412
–10• %
5
• • • 5•000 %
90.00
8•99 ✱
5.000
---------------------------------------------
8.99
800•
800
Markup and Profit Margin are both ways of calculating percent
profit.
– Profit margin is percent profit vs. selling price.
– Markup is percent profit vs. cost.
– Cost is the cost.
Knowing
Mrgn
Sell, Cost
Caution!
The socket outlet shall be installed near the equipment and
shall be easily accessible.
• • • 40•
MARKUP AND MARGIN
To find
12• ∆∆
12.
90•00 ✱
1,368• %
472•4412
5.
–10•00
123• ⴓ
123.
EXAMPLE 4: Convert 472.4412 inches to meters (1 meter =
39.3701 inches).
EXAMPLE 1: Set a 5% tax rate.
Calculate the tax on $800 and calculate the total
including tax.
A 10% discount on 100.
25.00
1368
39.3701
*: Press
to clear the memory before starting a memory
calculation.
TAX RATE CALCULATIONS
25• %
120•
14,814• ∆
3,588• +M ①
25.M
8
5• %
120
5• =
5
A 5% add-on to 100.
46• ×
78• =
77•77 =
0.143
22.22
EXAMPLE 2: Convert $120 to yen ($1 = ¥123.45).
④
1,234,567.
22.22 ⴓ 77.77 =
11•11ⴓ
123.450
46 ×78 = ①
+) 125 ⴓ 5 = ②
–) 72 × 8 = ③
Total
1234567
11.11
∆
123•450 =
1234567 → 1234578
11.11 ⴓ 77.77 =
11.11
123.45
1,200.
579.
1,385•42 ✱
1,385.42
EXAMPLE 1: Set the conversion rate ($1 = ¥123.45).
579• ✱
22•22 =
22.22
CONVERSION CALCULATION EXAMPLES
600• ✱+
62•35 ×
62.35
11.11
Operation
Cost
Sell
–
–
–
–
840.
EXAMPLE 2: Perform two calculations using $840 and $525,
both of which already include tax. Calculate the
tax on the total and the total without tax. (tax rate:
5%)
Ex.
Cost
$200
Operation
Sell
$250
GP
$50
200
20
Sell, Cost
Sell
Cost
Sell
Cost, Mrgn
Cost
Mrgn
Mkup
25%
Cost
Sell, Mrgn
Sell
Mrgn
Mrgn
20%
Sell
Cost, Mkup
Cost
Mkup
Cost
Sell, Mkup
Sell
Mkup
Page 2
840•
Sell is the selling price.
GP is the gross profit.
Mkup is the percent profit based on cost.
Mrgn is the percent profit based on selling price.
Mkup
EL-1607P(AB1)
600• –
001 • • • • • • • • • • • • •
62.35
123
500.•
100.–
•
500• +
600
500
CONSTANT
Display
200.
50.00
Print
200• ⴓ
Cost
840
840.
840• +
20• %M Mrgn
525
1,365.
525• +
1,365• ✱
250•00 ✱
Sell
50•00
GP
• • • 65• –
1,300•
EL-1607P(AB1)-2➀
1,300.
12.5.31, 6:17 PM
Adobe PageMaker 6.0J/PPC