User manual
Dishwasher
ZDF 204
Downloaded from DishWasher-Manual.com Manuals
Thank you for selecting our
appliance
We wish you lots of enjoyment with your new
appliance and we hope that you will consider
our brand again when purchasing household
appliances.
Please read this user manual carefully and
keep it throughout the product life cycle as a
reference document. The user manual should
be passed on to any future owner of the
appliance.
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Unloading the dishwasher _ _ _ _ _ _ _ _ 15
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ 16
Washing programmes _ _ _ _ _ _ _ _ _ _ _ 6
Environmental concerns _ _ _ _ _ _ _ _ _ 17
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7
Something not working _ _ _ _ _ _ _ _ _ 18
Set the water softener _ _ _ _ _ _ _ _ _ _ _ 8
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ 20
Filling with dishwasher salt _ _ _ _ _ _ _ _ 9
Consumption values _ _ _ _ _ _ _ _ _ _ _ 21
Filling with rinse aid _ _ _ _ _ _ _ _ _ _ _ 10
Hints for test institutes _ _ _ _ _ _ _ _ _ _ 21
Adjusting the dosage of rinse aid _ _ _ _ 11
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 22
Loading cutlery and dishes _ _ _ _ _ _ _ 12
European Guarantee _ _ _ _ _ _ _ _ _ _ _ 24
Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ 14
www.electrolux.com _ _ _ _ _ _ _ _ _ _ _ 25
Subject to change without notice
2Downloaded from DishWasher-Manual.com Manuals
Safety information
In the interest of your safety and to ensure the
correct use, before installing and first using the
appliance, read this user manual carefully, including its hints and warnings. To avoid
unnecessary mistakes and accidents, it is important to ensure that all people using the
appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the
appliance if it is moved or sold, so that everyone
using it through its life will be properly informed
on appliance use and safety.
Correct use
• This dishwasher is only intended for washing
household utensils suitable for machine
washing.
• Do not put any solvents in the dishwasher.
This could cause an explosion.
• Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
• Only use products (detergent, salt and rinse
aid) suitable for dishwashers.
• Avoid opening the door whilst the appliance
is in operation, hot steam may escape.
• Do not take any dishes out of the dishwasher
before the end of the dishwashing cycle.
• After use, isolate the appliance from the
power supply and turn off the water supply.
• This product should be serviced only by an
authorised service engineer, and only genuine spare parts should be used.
• Under no circumstances should you attempt
to repair the machine yourself. Repairs car-
ried out by inexperienced persons will cause
injury or serious malfunctioning. Contact
your local Service Force Centre. Always insist on genuine spare parts.
General safety
• Dishwasher detergents can cause chemical
burns to eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent
manufacturer.
• The water in your dishwasher is not for drinking. Detergent residues may still be present
in your machine.
• Ensure that the door of the dishwasher is
always closed when it is not being loaded or
unloaded. In this way you will avoid anybody
tripping over the open door and hurting
themselves.
• Do not sit or stand on the open door.
Child safety
• This appliance is designed to be operated
by adults. Don’t allow children to use the
dishwasher unsupervised.
• Keep all packaging well away from children.
There is risk of suffocation.
• Keep all detergents in a safe place out of
children’s reach.
• Keep children well away from the
dishwasher when the door is open.
Downloaded from DishWasher-Manual.com Manuals
3
Installation
• Check your dishwasher for any transport
damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier.
• All packaging must be removed before use.
• Any electrical and plumbing work required to
install this appliance must be carried out by
a qualified and competent person.
• For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
• Never use the dishwasher if the electrical
supply cable and water hoses are damaged;
or if the control panel, work top or plinth area
are damaged such that the inside of the appliance is freely accessible. Contact your
local Service Force centre, in order to avoid
hazard.
• All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
WARNING!
For electrical and water connection carefully
follow the instructions given in specific paragraphs.
Control panel
5
1
1.
2.
3.
4.
5.
Programme selector dial and On/Off switch
Start/cancel button
Half load button
Indicator lights
Programme selector indicator light
4Downloaded from DishWasher-Manual.com Manuals
4
2 3
Programme selector dial and On/Off switch
• when in this position, the machine is switched off
(corresponding light off),
• when the marker on the dial corresponds with a
programme, the machine is switched on and a programme is selected (programme selector indicator
light on)
Start/cancel button
• Starting the washing programme:
1. Select a washing programme.
2. Press the Start/Cancel button (corresponding
light on).
IMPORTANT!
Once the programme has started, if you want to
change the selection made you must cancel the washing programme in progress.
• Cancel the washing programme in progress:
1. Press and hold the Start/Cancel button until the
corresponding light turns off.
2. Release the Start/Cancel button.
3. Turn the programme selector dial to the Off position or select a new washing programme
(check that there is detergent in the detergent
dispenser).
Half load button
The option must be linked to the selection of a washing
programme. (See "Programme table" chart). When
selected, the corresponding light illuminates.
Load dishes in both baskets (lower and upper). When
using the option reduce the dosage of detergent which
is normally used for a complete load.
Programme selector indicator light
Illuminates when the washing programme is selected
Indicator lights
End of programme
Illuminates when the washing programme has ended.
Switch off the dishwasher by returning the programme
selector dial to the Off position. The On/Off indicator
light turns off.
It also has added functions of visual signalling as:
• the setting of the water softener,
• intervention of an alarm due to the malfunction of
the machine.
Downloaded from DishWasher-Manual.com Manuals
5
Indicator lights
Illuminates when special salt needs to be filled.
It can remain illuminated several hours after the salt
has been filled.
Salt refilling
Washing programmes
Programme
Half load
Degree of soil
Type of load
Programme description
Intensive 70°
Yes 1)
Heavy soil
Crockery, cutlery,
pots and pans
Prewash
Main wash
2 intermediate rinses
Final rinse
Drying
Normal 65°
Yes 1)
Normal soil
Crockery, cutlery,
pots and pans
Prewash
Main wash
1 intermediate rinses
Final rinse
Drying
60° A 30'2)
No
Light soil
Crockery and cutlery
Main wash
Final rinse
Bio 50° 3)
Yes4)
Normal soil
Crockery and cutlery
Prewash
Main wash
1 intermediate rinse
Final rinse
Drying
6Downloaded from DishWasher-Manual.com Manuals
Programme
Rinse and Hold
Half load
No
Degree of soil
Type of load
Any.
Partial load (to be completed later in the
day).
Programme description
1 cold rinse (to
avoid food scraps
from sticking
together).
This programme
does not require the
use of detergent.
1) When the Half load button is pressed, the prewash phase will be automatically excluded. In this case the detergent dose for
the prewash phase is no longer necessary.
2) Ideal for washing a partially loaded dishwasher. This is perfect daily programme, made to meet the needs of a family of 4
persons who only wish to load breakfast and dinner crockery and cutlery.
3) Test programme for test institutes.
4) When the Half load button is pressed, the duration of the washing phase is reduced.
First use
Before using your dishwasher for the first time:
• Ensure that the electrical and water connections comply with the installation instructions
• Remove all packaging from inside the appliance
• Set the water softener
• Pour 1 litre of water inside the salt container
and then fill with dishwasher salt
• Fill the rinse aid dispenser
When using tablets that
integrate rinse aid and
detergent:
there is no need to fill up with rinse aid
– set the water softener
– add special (dishwasher) salt
When using tablets that
integrate rinse aid, detergent,
salt function and other
additives:
there is no need to fill up with special salt or
rinse aid.
Check whether these detergents are suitable
for your water hardness. Follow the manufacturers instructions.
– Set the water hardness to level 1.
IMPORTANT!
If the drying results are not satisfactory we recommend that you:
1. Fill up the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
If you decide in future to use separated detergents, we advise that you:
Downloaded from DishWasher-Manual.com Manuals
7
– Fill up the salt and rinse aid container.
– Adjust the water hardness setting to the
highest level and perform 1 normal washing
programme without loading any dishes.
– Adjust the water hardness setting according
to the hardness of the water in your area.
– Adjust the rinse aid dosage
Set the water softener
The dishwasher is equipped with a water
softener designed to remove minerals and salts
from the water supply, which would have a detrimental or adverse effect on the operation of
the appliance.
The higher the content of these minerals and
salts, the harder your water is. Water hardness
is measured in equivalent scales, German deWater hardness
grees (°dH), French degrees (°TH) and mmol/
l (millimol per litre - international unit for the
hardness of water).
The softener should be adjusted according to
the hardness of the water in your area. Your
local Water Authority can advise you on the
hardness of the water in your area.
Adjusting the water hardness
setting
Use of salt
°dH
°TH
mmol/l
manually
electronically
51 - 70
91 - 125
9,1 - 12,5
2
level 10
yes
43 - 50
76 - 90
7,6 - 8,9
2
level 9
yes
37 - 42
65 - 75
6,5 - 7,5
2
level 8
yes
29 - 36
51 - 64
5,1 - 6,4
2
level 7
yes
23 - 28
40 - 50
4,0 - 5,0
2
level 6
yes
19 - 22
33 - 39
3,3 - 3,9
2
level 5
yes
15 - 18
26 - 32
2,6 - 3,2
1
level 4
yes
11 - 14
19 - 25
1,9 - 2,5
1
level 3
yes
4 - 10
7 - 18
0,7 - 1,8
1
level 2
yes
<4
<7
< 0,7
1
level 1
no
The water softener must be set in both ways:
manually, using the water hardness dial and
electronically.
8Downloaded from DishWasher-Manual.com Manuals
Setting the water softener manually (see table)
The water softener is factory set at position 2.
Set switch to position 1 or
2
Setting the water softener electronically (see table)
The water softener is factory set at position 5.
The dishwasher must be switched off .
Release the button. The end of programme indicator
light will flash. The number of flashes corresponds to
current level set.
The end of programme indicator light might flash 5
times, for example. The flashing is repeated every 5
seconds.
To change the level, press the start/cancel button.
Each time the button is pressed the level increases.
Press and hold the start/cancel button and turn the (Level 1 follows level 10).
programme selector dial clockwise till the first proThe end of programme indicator light indicates the new
gramme.
setting.
Keep the button pressed until the programme selector To memorise the operation, turn the programme seindicator light and the start/cancel indicator light start lector dial to position off.
flashing.
Filling with dishwasher salt
CAUTION!
Use only special salt suitable for dishwashers.
Downloaded from DishWasher-Manual.com Manuals
9
Unscrew the cap.
Only before filling with Using the funnel provided,
salt for the first time, fill pour in the salt until the
the salt container with wa- container is filled with salt.
ter.
IMPORTANT!
Immediately start a complete programme.
IMPORTANT!
Water will overflow from the container as salt is added.
Remove any trace of salt. Replace the cap tightly
turning it clockwise until it
stops with a click.
IMPORTANT!
Top up the special salt when the light on the
control panel illuminates.
Downloaded from DishWasher-Manual.com Manuals
10
Filling with rinse aid
Open the lid.
Fill up with rinse aid. The Clean up any rinse aid
maximum level for filling is which overflows. Close
the lid and press until it
indicated by "max"
locks.
CAUTION!
Never fill the rinse aid dispenser with any other substances (e.g. dishwasher
cleaning agent, liquid detergent). This would damage the appliance.
Top up the rinse aid indicator (B) becomes clear
Adjusting the dosage of rinse aid
Increase the dose if there are drops of water or
lime spots on the dishes after washing.
Reduce the dose if there are whitish streaks on
the dishes or a bluish film on glassware or knife
blades.
Downloaded from DishWasher-Manual.com Manuals
11
Open the lid.
Set the dosage level. (The Close the lid and press undose is factory set in po- til it locks.
sition 4).
Loading cutlery and dishes
Sponges, household cloths and any object that
can absorb water may not be washed in the
dishwasher.
• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in pans
• When loading the dishes and cutlery, please
note:
– Dishes and cutlery must not impede the
rotation of the spray arms.
– Load hollow items such as cups, glasses,
pans, etc. with the opening downwards so
that water cannot collect in the container
or a deep base.
– Dishes and items of cutlery must not lie
inside one another, or cover each other.
– To avoid damage to glasses, they must
not touch.
– Lay small objects in the cutlery basket.
• Plastic items and pans with non stick coatings have a tendency to retain water drops;
these items will not dry as well as porcelain
and steel items.
• Light items (plastic bowls etc.) must be loaded in the upper basket and arranged so
they do not move.
Downloaded from DishWasher-Manual.com Manuals
12
For washing in the dishwasher the following cutlery and dishes
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn, china or mother-of• Only wash stoneware in the dishwasher if it is
pearls handles.
specially marked as being dishwasher-safe by the
manufacturer.
• Plastic items that are not heat resistant.
•
Glazed
patterns may fade if machine washed
• Older cutlery with glued parts that are not temperafrequently.
ture resistant.
• Silver and aluminium parts have a tendency to dis• Bonded cutlery items or dishes.
colour during washing: Residues, e.g. egg white,
• Pewter or copper items.
egg yolk and mustard often cause discolouring and
• Lead crystal glass.
staining on silver. Therefore always clean left-overs
• Steel items prone to rusting.
from silver immediately, if it is not to be washed
• Wooden platters.
straight after use.
• Items made from synthetics fibres.
Load cutlery. For best results we recommend you
to use the cutlery grid provided (if the size and dimensions of the cutlery
allow it)
Place knives and other
items of cutlery with sharp
points or edges with their
handles facing upwards.
Risk of injury!
Load the lower basket. Arrange serving dishes and
large lids around the edge
of the basket.
Downloaded from DishWasher-Manual.com Manuals
13
Load upper basket. Light
items (plastic bowls etc.)
must be loaded in the upper basket and arranged
so they do not move.
For taller items, the cup
racks can be folded upwards.
If plates are to be loaded in the upper basket: load
them starting from the rear positions; tilting them
slightly forwards and avoiding the front positions near
the door.
Adjusting the height of the
upper basket
If washing very large plates you can load them
in the lower basket after moving the upper basket to the higher position.
Maximum height of the dishes in:
upper basket
lower basket
With upper basket raised
20 cm
31 cm
With upper basket lowered
24 cm
27 cm
IMPORTANT!
When the basket is in the higher position you will not
be able to use the cup racks.
Move the front runner
stops (A) of the upper basket outwards and slide the
basket out.
Refit the basket in the
higher position and replace the stops (A) in their
original position.
Downloaded from DishWasher-Manual.com Manuals
14
Use of detergent
IMPORTANT!
Only use detergents suitable for dishwashers.
Open the lid.
Observe the manufacturer’s dosing and storage recommendations.
Fill in the detergent in
compartment A.
Observe the dosing levels.
For programmes with pre- When using detergent
Close the lid.
wash add an additional
tablets: place detergent
detergent dose in comtablets in compartment A.
partmentB.
Detergent tablets
Detergent tablets from different manufacturers
dissolve at different rates. For this reason,
some detergent tablets do not attain their full
cleaning power during short washing programmes. Therefore, please use long washing
programmes when using detergent tablets, to
ensure the complete removal of detergent
residuals.
Unloading the dishwasher
• Hot dishes are sensitive to knocks.
The dishes should therefore be allowed to
cool down before removing from the appliance.
• Empty the lower basket first and then the
upper one; this will avoid water dripping from
the upper basket onto the dishes in the lower
one.
Downloaded from DishWasher-Manual.com Manuals
15
• Water may appear on the sides and the door
of the dishwasher as the stainless steel will
eventually become cooler than the dishes.
CAUTION!
When the washing programme has finished, it
is recommended that the dishwasher is unplugged and the water tap turned off.
Care and cleaning
Cleaning the filters
IMPORTANT!
NEVER use the dishwasher without filters. Incorrect repositioning and fitting of the filters will
produce poor washing results.
Clean filters A, B and C Turn the handle about 1/4 Remove filter A from the
thoroughly under running turn anticlockwise and re- base of the washing comwater.
move filters B and C.
partment.
Put the flat filter A back in Replace the filters and
the base of the washing lock by turning the handle
compartment and ensure clockwise to the stop.
that it fits perfectly under
the two guidesD.
Downloaded from DishWasher-Manual.com Manuals
16
If residues of soil have clogged the holes in the
spray arms, remove them with a cocktail stick.
1. Unplug the appliance and then turn off the
water.
2. Leave the door ajar to prevent the formation of any unpleasant smells.
3. Leave the inside of the machine clean.
External cleaning
Frost precautions
Clean the external surfaces of the machine and
control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc....).
Avoid placing the machine in a location where
the temperature is below 0°C. If this is
unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe
and empty it.
Internal cleaning
Moving the machine
Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned
regularly with a damp cloth.
We recommend every 3 months to run the wash
programme for heavy soiled dishes using detergent but without dishes.
If you have to move the machine (moving house
etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
Cleaning the spray arms
NEVER try to remove the spray arms.
Prolonged periods of nonoperation
If you are not using the machine for any prolonged period of time you are advised to:
Environmental concerns
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging
materials in the appropriate container at the
community waste disposal facilities.
Downloaded from DishWasher-Manual.com Manuals
17
CAUTION!
When a unit is no longer being used:
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose of
them.
• Dispose of the door catch. This prevents
children from trapping themselves inside
and endangering their lives.
The symbol
on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should
be taken to the appropriate collection point for
the recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of this
product. For more detailed information about
recycling of this product, please contact your
local council, your household waste disposal
service or the shop where you purchased the
product.
Something not working
The dishwasher will not start or stops during
operation.
Certain problems are due to the lack of simple
maintenance or oversights, which can be
solved with the help of the indications described
in the chart, without calling out an engineer.
Switch off the dishwasher, open the door and
carry out the following suggested corrective actions.
Fault code and malfunction
Possible cause and solution
• continuous flashing of the start/cancel indicator
light
• 1 flash of the end of programme indicator light
The dishwasher does not fill with water
• The water tap is blocked or furred with limescale
Clean the water tap
• The water tap is turned off
Turn the water tap on
• The filter (where present) in the threaded hose fitting
at the water inlet valve is blocked
Clean the filter in the threaded hose
• The water inlet hose has not been correctly laid or
it is bent or squashed
Check the water drain hose connection
• continuous flashing of the start/cancel indicator
light
• 2 flashes of the end of programme indicator light
The dishwasher will not drain
• The sink spigot is blocked
Clean out the sink spigot
• The water drain hose has not been correctly laid or
it is bent or squashed
Check the water drain hose connection
Downloaded from DishWasher-Manual.com Manuals
18
Fault code and malfunction
Possible cause and solution
• continuous flashing of the start/cancel indicator
light
• 3 flashes of the end of programme indicator light
• Anti-flood device is activated
Close the water tap and contact your local Service
Force Center.
• The programme does not start
• The dishwasher’s door has not been properly
closed
Close the door
• The main plug is not plugged in
Insert the main plug
• The fuse has blown out in the household fuse box
Replace the fuse
• Delay start has been set
If dishes are to be washed immediately, cancel the
delay start
Once these checks have been carried out;
close the dishwasher’s door and switch on the
appliance. Press the button of the programme
that was running before the intervention of the
alarm. The programme will continue from the
point at which it was interrupted.
If the malfunction or fault code reappears contact the Service Force Centre.
For other fault codes not described in the above
chart, please contact your Service Force Centre.
Contact your local Service Force Centre, quoting the model (Mod.), product number (PNC)
and serial number (S.N.).
This information can be found on the rating
plate located on the side of the dishwasher
door.
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . .
PNC :. . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . .
Downloaded from DishWasher-Manual.com Manuals
19
The wash results are not satisfactory
The dishes are not clean
• The wrong washing programme has been selected.
• The dishes are arranged in such a way as to stop
water reaching all parts of the surface. The baskets
must not be overloaded.
• The spray arms do not rotate freely due to incorrect
arrangement of the load.
• The filters in the base of the washing compartment
are dirty or incorrectly positioned.
• Too little or no detergent has been used.
• Where there are limescales deposits on the dishes;
the salt container is empty or the incorrect level of
the water softener has been set.
• The drain hose connection is not correct.
• The salt container cap is not properly closed.
The dishes are wet and dull
• Rinse aid was not used.
• The rinse aid dispenser is empty.
There are streaks, milky spots or a bluish coating on
glasses and dishes
• Decrease rinse aid dosing.
Water drops have dries onto glasses and dishes
• Increase rinse aid dosing.
• The detergent may be the cause. Contact the detergent manufacturer’s consumer care line.
If after all these checks, the problem persists,
contact your local Service Force Centre.
Technical data
Dimensions
Width x Height x Depth
cm
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher’s door.
Water supply pressure
Minimum - Maximum
(MPa)
0,05 - 0,8
Capacity
place settings
12
Max. weight
kg
40,5
Downloaded from DishWasher-Manual.com Manuals
20
60,0 x 85,0x 61,0
Noise level
dB(A)
51
Consumption values
iations of the power supply and the amount of
dishes.
The consumption values are intended as a
guide and depends on the pressure and the
temperature of the water and also by the var-
Consumption values
Programme
Programme duration (in Energy consumption (in
minutes)
kWh)
Water (litres)
Intensive 70°
85-95
1,8-2,0
22-25
Normal 65°
105-115
1,5-1,7
23-25
65°A30'
30
0,9
9
BIO 50° (Test programme for Test Institutes)
140
1,05
16
Rinse and Hold
12
<0,1
5
Hints for test institutes
Testing in accordance with EN 60704 must be
carried out with appliance fully loaded and using the test programme (see "Consumption
values").
Test in accordance with EN 50242 must be
carried out when the salt container and rinse
aid dispenser have been filled with salt and
rinse aid respectively and using the test programme (see "Consumption values").
Full load: 12 standard place settings
Amount of detergent required
5 g + 25 g (Type B)
Rinse aid setting
position 4 (Type III)
Downloaded from DishWasher-Manual.com Manuals
21
Upper basket
Cutlery basket
Lower basket
cup racks: position A
Installation
WARNING!
Any electrical and/or plumbing work required to
install this appliance should be carried out by a
qualified electrician and/or plumber or competent person.
Water connection
WARNING!
The dishwasher must not be connected to open
water appliances or instantaneous water heaters. This dishwasher may be fed with either hot
(max. 60°) or cold water. Nevertheless we advise you a cold water supply.
WARNING!
Only use, for connection to the water mains,
new hose-set; old hose-set must not be reused.
CAUTION!
If the machine is connected to new pipes or
pipes which have not been used for a long time,
you should run the water for a few minutes before connecting the inlet hose.
Downloaded from DishWasher-Manual.com Manuals
22
Inlet hose
Connect the inlet hose to a water tap with an external
thread of 3/4”.
The inlet hose can be turned either to the left or the
right to suit the installation by means of the locknut.
The locknut must be correctly fitted to avoid water
leaks.
Drain hose
Connect drain hose to the Required height: 30 to 100 Ensure that the hoses are When connecting the
sink.
cm above bottom of the
not kinked, crushed or en- drain hose to an under
dishwasher.
tangled.
sink trap spigot, the entire
plastic membrane (A)
must be removed. Failure to remove all the membrane will result in food
particles building up over
time eventually blocking
the dishwasher drain hose
spigot.
If you use a drain hose extension the total
length should not be longer than 4 metres.
Likewise the internal diameter of the couplings
used for connections to the waste outlet must
be no smaller than the diameter of the hose
provided.
Downloaded from DishWasher-Manual.com Manuals
23
Electrical connection
CAUTION!
Safety standards require the appliance to be
earthed.
Prior to using the appliance for the first time,
ensure that the rated voltage and type of supply
on the rating plate match that of the supply
where the appliance is to be installed.
The fuse rating is also to be found on the rating
plate.
Always plug the mains plug into a correctly installed shockproof socket. Multi-way plugs,
connectors and extension cables must not be
used.
This could constitute a fire hazard through overheating.
If necessary, have the domestic wiring system
socket replaced. In case that the electrical ca-
ble has to be replaced, contact your local Service Force centre.
The plug must be accessible after the appliance
has been installed.
Never unplug the appliance by pulling on the
cable. Always pull the plug.
The manufacturer accepts no liability for failure
to observe the above safety precautions.
Fitting under a counter
By removing the dishwasher’s worktop, you can
install it under a close fitting sink unit or a preexisting top.
Be sure that once the appliance has been installed, it is easily accessible for the service
engineer in the event that a repair is required.
Levelling
Good levelling is essential for correct closure and
sealing of the door.
When the appliance is correctly levelled, the door will
not catch on either side of the cabinet.
Downloaded from DishWasher-Manual.com Manuals
24
European Guarantee
This appliance is guaranteed by Electrolux in
each of the countries listed at the back of this
user manual, for the period specified in the appliance guarantee or otherwise by law. If you
move from one of these countries to another of
the countries listed, the appliance guarantee
will move with you subject to the following qualifications:• The appliance guarantee starts from the
date you first purchased the appliance which
will be evidenced by production of a valid
purchase document issued by the seller of
the appliance.
• The appliance guarantee is for the same
period and to the same extent for labour and
parts as exists in your new country of resi-
dence for this particular model or range of
appliances.
• The appliance guarantee is personal to the
original purchaser of the appliance and cannot be transferred to another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e.
is not used for commercial purposes.
• The appliance is installed in accordance with
all relevant regulations in force within your
new country of residence.
The provisions of this European Guarantee do
not affect any of the rights granted to you by
law.
www.electrolux.com
Albania
+35 5 4 261 450
Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/Belgien
+32 2 363 04 44
Bergensesteenweg 719, 1502
Lembeek
Česká republika
+420 2 61 12 61 12
Budějovická 3, Praha 4, 140 21
Danmark
+45 70 11 74 00
Sjællandsgade 2, 7000 Fredericia
Deutschland
+49 180 32 26 622
Muggenhofer Str. 135, 90429 Nürnberg
Eesti
+37 2 66 50 030
Pärnu mnt. 153, 11624 Tallinn
España
+34 902 11 63 88
Carretera M-300, Km. 29,900
Alcalá de Henares Madrid
France
www.electrolux.fr
Great Britain
+44 8705 929 929
Downloaded from DishWasher-Manual.com Manuals
Addington Way, Luton, Bedfordshire LU4 9QQ
25
Hellas
+30 23 10 56 19 70
4, Limnou Str., 54627 Thessaloniki
Hrvatska
+385 1 63 23 338
Slavonska avenija 3, 10000 Zagreb
Ireland
+353 1 40 90 753
Long Mile Road Dublin 12
Italia
+39 (0) 434 558500
C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Latvija
+37 17 84 59 34
Kr. Barona iela 130/2, LV-1012,
Riga
Lietuva
+370 5 278 06 03
Ozo 10a, LT-08200 Vilnius
Luxembourg
+352 42 431 301
Rue de Bitbourg, 7, L-1273 Hamm
Magyarország
+36 1 252 1773
H-1142 Budapest XIV, Erzsébet
királyné útja 87
Nederland
+31 17 24 68 300
Vennootsweg 1, 2404 CG - Alphen
aan den Rijn
Norge
+47 81 5 30 222
Risløkkvn. 2 , 0508 Oslo
Österreich
+43 18 66 400
Herziggasse 9, 1230 Wien
Polska
+48 22 43 47 300
ul. Kolejowa 5/7, Warszawa
Portugal
+35 12 14 40 39 39
Quinta da Fonte - Edificio Gonçalves Zarco - Q 35 -2774-518
Paço de Arcos
Romania
+40 21 451 20 30
Str. Garii Progresului 2, S4, 040671
RO
Schweiz - Suisse - Svizzera
+41 62 88 99 111
Industriestrasse 10, CH-5506 Mägenwil
Slovenija
+38 61 24 25 731
Gerbičeva ulica 98, 1000 Ljubljana
Slovensko
+421 2 43 33 43 22
Electrolux Slovakia s.r.o., Electrolux Domáce spotrebiče SK,
Seberíniho 1, 821 03 Bratislava
Suomi
www.electrolux.fi
Sverige
+46 (0)771 76 76 76
Electrolux Service, S:t Göransgatan 143, S-105 45 Stockholm
Türkiye
+90 21 22 93 10 25
Tarlabaşı caddesi no : 35 Taksim
İstanbul
Россия
+7 495 937 7837
129090 Москва, Олимпийский
проспект, 16, БЦ "Олимпик"
Downloaded from DishWasher-Manual.com Manuals
26
Україна
+380 44 586 20 60
Downloaded from DishWasher-Manual.com Manuals
04074 Київ, вул.Автозаводська,
2а, БЦ "Алкон"
27
www.electrolux.com
Downloaded from DishWasher-Manual.com Manuals
156990920-00-022008