INVERTER
FR-D700-SC-EC
Safety stop function instruction manual
CONTENTS
1. General description ............................................................................. 1
2. Installation and wiring ......................................................................... 2
3. Example of safety system configuration ........................................... 5
4. Test and checking failure .................................................................... 7
5. Safety parameters of FR-D700-SC...................................................... 8
Compliance with the EU Machinery Directive – Functional Safety
WARNING
Any misuse of safety function could lead to personal injury or death, property damage, or economic loss.
To ensure that the system complies fully with requirement of safety, make a system-level risk assessment.
Mitsubishi Electric Co. cannot assume responsibility for any system to comply with safety directive.
CAUTION
The information of this manual is merely a guide for proper installation.
Mitsubishi Electric Co. cannot assume responsibility for the compliance or the noncompliance to any code,
national, local or otherwise for the proper installation of this equipment.
A hazard of personal injury and/or equipment damage exists if codes are ignored during installation.
WARNING
To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before
performing any work on the drive. Measure the DC bus voltage at the P(+) and N(-) terminals or test points
(refer to your drive’s User Manual for locations and discharging time). The voltage must be zero.
WARNING
The safety stop function do not isolate electrically between drive and motor. To avoid an electric shock
hazard, disconnect/isolate power to the drive and verify to ensure that the voltage is zero before
performing any work on the motor (refer to your drive’s User Manual for discharging time).
CAUTION
This instruction manual is compatible with FR-D700-SC-EC source-logic safety terminal model. For
FR-D700-EC sink-logic safety terminal model, refer to the FR-D700 safety stop function instruction manual
(BCN-A211508-000).
1. General description
Features
Mitsubishi FR-D700-SC safety stop function prevents a drive from supplying rotational energy to motors.
Dual safety channels ‘S1’ and ‘S2’ cut off the gate-drive power for IGBT to turn off.
Input power
FR-D700-SC
S1
S2
Internal
Safety
Circuit
Safety relay module
+24V
CPU
G
G
Gate
Driver
Gate
Driver
IGBTs
SC
M
Fig.1 FR-D700-SC safety stop function diagram
WARNING
The safety stop function doesn’t isolate electrically between drive and motor. To avoid an electric shock
hazard, disconnect power to the drive and verify that the voltage is zero before performing any work on the
motor (refer to your drive’s User Manual for discharging time).
Directives
Mitsubishi FR-D700-SC safety stop function meets the following directives and categories.
ISO13849-1:2008 Category 3/PLd
IEC62061:2005 / IEC61800-5-2:2007 / IEC61508 SIL2
IEC60204-1:2006 / IEC61800-5-2:2007 Stop category 0
WARNING
The misuse of safety function leads to personal injury or death, property damage, or economic loss.
To ensure that the system complies fully with requirement of safety, make a system-level risk assessment.
Mitsubishi Electric Co. cannot assume responsibility for any system to comply with safety directive.
1
2. Installation and wiring
CAUTION
The following information is merely a guide for proper installation.
Mitsubishi Electric Co. cannot assume responsibility for the compliance or the noncompliance to any code,
national, local or otherwise for the proper installation of this equipment.
A hazard of personal injury and/or equipment damage exists if codes are ignored during installation.
CAUTION
Ensure the safety relay unit and the FR-D700-SC unit is mounted closely in enclosure meeting IP54 and
all interconnection wiring is short and protected against open and short circuit faults.
Refer EN/ISO13849-2.
Installation
Mitsubishi FR-D700-SC safety stop function should be used under following condition and environment.
Table.1 The condition and environment for using safety stop function
Item
Temperature
Operation
range
Storage
Ambient humidity
Vibration
Altitude
Atmosphere
Over voltage category
Pollution degree
Mounting
Condition
-10°C to +50°C (non-freezing)
-20°C to +65°C
90%RH maximum (non-condensing)
5.9m/s2 or less
maximum 1000m above sea level
Indoors (without corrosive gas, flammable gas, oil mist, dust and dirt etc.)
II or less
II or less
wall mounting / vertical orientation
CAUTION
In order to meet safety stop, an approved safety relay unit to ISO13849-1/EN954-1 safety category 3 or better shall be
used in conjunction with FR-D700-SC as shown in example1,2.
In addition, all other components with in the safety stop loop shall be ‘safety approved’ types.
WARNING
To avoid an electric shock hazard, insert the magnetic contactor (MC) between power source and drive.
Open the contact of MC and keep away from drive for discharging time (refer to your drive’s User Manual
for information) before performing any work on the drive.
And verify that the voltage on the bus capacitors has discharged before Measure the DC bus voltage at the
P(+) and N(-) terminals or test points (refer to your drive’s User Manual for locations). The voltage must be
zero.
CAUTION
To avoid systematic faults, a test even for faulty demands of the safety function has to be performed in order to check
the correct function of the monitor signal. This test shall be carried out at system installation, any software changes,
parameterization changes, and/or at least once per year.
Refer to ‘4. Test and checking failure’.
2
Wiring
The safety related terminals are described in Table.2 and Table.3
Table.2 The safety related terminals
Terminal
Symbol
S1
S2
SC
SO
(SAFE)
RUN
(SAFE2)
SE
Description
Rating
For input of safety stop channel1.
S1-SC is
Open: In safety stop mode.
Short: Non safety stop mode.
For input of safety stop channel2.
S2-SC is
Open: In safety stop mode.
Short: Non safety stop mode.
Common terminal for S1, S2 terminals.
*SC is connected terminal PC internally.
Input resistance:4.7kΩ
Current : 4 to 6 mA
(In case of shorted to SC)
Voltage : 21 to 26 V
(In case of open from SC)
As output for safety stop condition.
SO terminal type is ‘Open collector output’.
SO-SE is
OFF(Open): Drive enabled, or drive shutoff (with
internal circuit fault)
ON(Close): Drive shutoff (no internal circuit fault)
Important: SO terminal should be used for monitoring safety stop
condition only. SO terminal cannot be used for safety function.
As output for failure detection and alarm. RUN terminal type is ‘Open
collector output’.
RUN-SE is
OFF(Open): Detect failure or Alarm.
ON(Close): No failure detected.
Attention: To use RUN terminal for monitor output of failure
detection, The parameter No.190 should be set 81
(Safety monitor 2).
Note: This terminal can be used for alarm or to prevent restart only,
no other safety function.
Common terminal for safety RUN and SO terminal.
3
Load: 24VDC/0.1A max.
Voltage drop: 3.4V max.
(In case of ‘ON’ state)
Table.3 Truth table of Safety related signals
Input power
S1-SC
S2-SC
OFF
-
-
Short
Short
Open
Open
Short
Open
Open
Short
ON
Internal safety
circuit fault *1
No failure
Detected
No failure
Detected
N/A
N/A
SO (SAFE)
RUN (SAFE2) *2
Drive state
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
OFF(Open)
ON(Close)
Drive enable
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
ON(Close)
ON(Close)
Drive shutoff (Safe state)
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
" N/A " denotes a condition where circuit fault does not apply.
*1
At an internal safety circuit fault, one of E.SAF or E.CPU is displayed on the operation panel. SA is displayed on the operation
*2
To use RUN terminal for monitor output of failure detection, the parameter No.190 should be set 81 (Safety monitor 2).
panel while S1 and S2 signals are both open and the safety function operates (without internal safety circuit fault).
Wire and ferrule specification
Table.4 wire and ferrule specification
Wire size (mm )
Ferrule with insulation collar *
0.3 / 0.5
AI 0,5-10WH
0.75
AI 0,75-10GY
1
AI 1-10RD
1.25 / 1.5
AI1,5-10BK
0.75 (combined 2 wire)
AI TWIN 2 X 0,75-10GY
*Ferrules and tools are distributed by Phoenix Contact.
2
Crimping tool *
CRIMPFOX 6
Jumper cable
The jumper cable between S1,S2 and SC terminal has been installed in the factory as shown in Fig.2.
AM
Fig.2. Short wire
Before connecting safety input wire to S1,S2 and SC terminal, remove this jumper cable.
4
3. Example of safety system configuration
R/L1 S/L2 T/L3
RUN (SAFE2)
SE
STF
START
STF
Emergency
stop button
STOP
+24V
X0
COM0
X1
Internal
Safety
Circuit
DC24V
COM1
XS0
XS1
Z00
IGBTs
CPU
STOP
Z10
Z20
Gate
Driver
Gate
Driver
G
G
S2
K1
S1
K2
+24V
24G
Z01
MITSUBISHI MELSEC Safety relay module
QS90SR2SN-Q
Z11
Z21
SC
PC
FR-D700-SC
U
V
W
IM
Fig.3 Safety system example – STOP synchronous with emergency stop button and fault
detection through RUN output.
For safety stop, configure the wiring as shown in Fig.3 above.
Note: the above wiring is configured to prevent restart in case of a fault.
XS0 should be connected to RUN terminal and XS1 should be connected to SE, because polarity of XS0 is
positive, XS1 is negative.
The parameter No.190 (RUN terminal function selection) must be set to ‘81’. This setting makes the RUN
output to turn off in case of failure.
After the power-up, to reset the safety stop mode, press the START switch, and also press the STF switch,
then start the motor rotation.
In the above Fig.3, wired example, in the event of reset of ‘safe-condition’ the motor rotation will not occur
until STF is pressed.
(for normal ‘non-safety’ STF/STOP function, please refer to your drive’s User Manual)
CAUTION
To prevent restart in case of recovering from input power loss of drive, 3-wired connection for STF/STOP
control is recommended.
In case of 2-wire connection and using latching type switch to short between STF and PC for starting,
ensure the compliance with safety requirement for the restarting when the drive recover from input power
loss.
5
R/L1 S/L2 T/L3
RUN (SAFE2)
SE
START
Emergency
stop button
+24V
X0
COM0
X1
Internal
Safety
Circuit
DC24V
IGBTs
CPU
COM1
XS0
XS1
Z00
Z10
Z20
S1
Gate
Driver
Gate
Driver
G
G
K1
S2
K2
+24V
24G
Z01
Z11
Z21
SC
MITSUBISHI MELSEC Safety relay module
QS90SR2SN-Q
FR-D700-SC
U
V
W
IM
R/L1 S/L2 T/L3
RUN
(SAFE2)
SE
IGBTs
CPU
S1
Gate
Driver
Gate
Driver
G
G
S2
+24V
SC
FR-D700-SC
U
V
W
IM
Fig.4 Example when using multiple FR-D740-SC inverters for the safety stop function
The parameter No.190 (RUN terminal function selection) must be set to ‘81’. This setting makes the RUN
output to turn off in case of failure.
NOTE
Do not connect the FR-D700 sink-logic safety terminal model together with FR-D700-SC source-logic
safety terminal model. If connected together, the safety stop function does not work properly.
6
4. Test and checking failure
CAUTION
To avoid systematic faults, a test even for faulty demands of the safety function has to be performed in order to check
the correct function of the monitor signal. This test shall be carried out at system installation, any software changes,
parameterization changes, and/or at least once per year.
I/O status and failure
FR-D700-SC safety related I/O status obeys the following truth table.
Table.5 Truth table of Safety related signals
Input power
S1-SC
S2-SC
OFF
-
-
Short
Short
Open
Open
Short
Open
Open
Short
ON
Internal safety
circuit fault *1
No failure
Detected
No failure
Detected
N/A
N/A
SO (SAFE)
RUN (SAFE2) *2
Drive state
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
OFF(Open)
ON(Close)
Drive enable
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
ON(Close)
ON(Close)
Drive shutoff (Safe state)
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
OFF(Open)
OFF(Open)
Drive shutoff (Safe state)
" N/A " denotes a condition where circuit fault does not apply.
*1
At an internal safety circuit fault, one of E.SAF or E.CPU is displayed on the operation panel. SA is displayed on the operation
*2
To use RUN terminal for monitor output of failure detection, the parameter No.190 should be set 81 (Safety monitor 2).
panel while S1 and S2 signals are both open and the safety function operates (without internal safety circuit fault).
In case of diagnostic or functionality test, check the I/O state whether it is same or not as Table.5.
Diagnostic
If the failure detected, FR-D700-SC output alarm signal and indicate ‘E.SAF’ at the display.
In case of FR-D700-SC output the alarm, please take following action.
(1) Check the S1-SC and S2-SC input signal logic is the same. If these are different logic, correct the input
signal and reset the FR-D700-SC.
(2) Disconnect the wire from S1, S2, SC terminal, then reset or power-off and on, If the ‘SA’ letter is
flashed up at display, there is failure in system except FR-D700-SC. But, still ‘E.SAF’ is displayed and
alarm output, there is malfunction on FR-D700-SC.
Self diagnostic test
FR-D700-SC does the self-diagnostic test on the power-ON.
If FR-D700-SC output alarm at power-ON, please take the action described in ‘Diagnostic’ at above.
Test procedure for functionality
As depicted ‘ATTENTION’ in above, the test for the functionality is important.
Please do the test following procedure.
(1) Please make each state of S1-SC and S2-SC depicted at Table.5.
(2) If there is any different state from Table.5, FR-D700-SC has some malfunction.
(3) If there is no different state from Table.5, check the systematic performance, such as, press the
Emergency switch, press the start/restart button at the failure detected (RUN-SE opened), and so on.
(4) Finally clear the error record of the FR-D700-SC (see the user manual how to clear the error record).
7
5. Safety parameters of FR-D700-SC
FR-D700-SC safety related I/O status obeys the following truth table.
Table.6 Safety parameters of FR-D700-SC
Parameter
PFDAVG
PFHD
PL
MTTFD
DCAVG
Value
2.06x10-4
2.35x10-9
d
725 years
60%
8
REVISIONS
Print Date
Manual Number
Jan. 2012
BCN-A211508-005-A
BCN-A211508-005-A
Revision
First edition
9
HEADQUARTERS
EUROPEAN REPRESENTATIVES
EUROPEAN REPRESENTATIVES
EUROPEAN REPRESENTATIVES
MITSUBISHI ELECTRIC
EUROPE
EUROPE B.V.
German Branch
Gothaer Straße 8
D-40880 Ratingen
Phone: +49 (0) 21 02 / 486-0
Hotline: +49 2102 1805 000-765 /-766
Fax: +49 (0) 21 02 / 4 86-1 12 0
e mail: megfa-mail@meg.mee.com
www.mitsubishi-automation.com
GEVA
AUSTRIA
Wiener Straße 89
A-2500 Baden
Phone: +43 (0) 2252 / 85 55 20
Fax: +43 (0) 2252 / 488 60
e mail: office@geva.co.at
MITSUBISHI ELECTRIC
IRELAND
EUROPE B.V.-Irish Branch
Westgate Business Park
Ballymount
IRL-Dublin 24
Phone: +353 (0) 1 / 419 88 00
Fax: +353 (0) 1 / 419 88 90
e mail: sales.info@meuk.mee.com
Beijer Electronics AB
SWEDEN
Box 426
S-20123 Malmö
Phone: +46 (0) 40 / 35 86 00
Fax: +46 (0) 40 / 93 23 02
e mall: ——
MITSUBISHI ELECTRIC
FRANCE
FRANCE
25, Boulevard des Bouvets
F-92741 Nanterre Cedex
Phone: +33 1 55 68 55 68
Fax: +33 1 49 01 07 25
e mail: factory.automation@fra.mee.com
MITSUBISHI ELECTRIC
ITALY
EUROPE B.V.
Italian Branch
C.D. Colleoni-P. Perseo lng. 2
Via Paracelso 12
I-20041 Agrate Brianza (Ml)
Phone: +39 (0) 39 / 60 53 1
Fax: +39 (0) 39 / 60 53 312
e mail: factory.automation@it.mee.com
MITSUBISHI ELECTRIC
SPAIN
EUROPE B.V.
Pol. lnd. Can Magi-C.
Calle Joan Buscallá, 2-4 AC 420
E-08190 Sant Cugat del Vallés
Phone: +34 (9) 3 / 565 31 31
Fax: +34 (9) 3 / 589 29 48
MITSUBISHI ELECTRIC
UK
EUROPE B.V.
UK Branch
Travellers Lane
Hatfield, Hertfordshire, AL10 8 XB
Phone: +44 (0) 1707 / 27 61 00
Fax: +44 (0) 1707 / 27 86 95
MITSUBISHI ELECTRIC
JAPAN
CORPORATION
Tokyo Bldg.
2-7-3 Marunouchi Chiyoda-Ku
Tokyo 100-8310
Phone: +81 (0) 3 / 32 18 31 76
Fax: +81 (0) 3 / 32 18 24 22
MITSUBISHI ELECTRIC
AUTOMATION
500 Corporate Woods Parkway
Vernon Hills, Illinois 60061
Phone: +1 (0) 847 / 478 21 00
Fax: +1 (0) 847 / 478 03 27
USA
Getronics b.v.
BELGIUM
Control Systems
Pontbeeklaan 43
B-1731 Asse-Zellik
Phone: +32 (0) 2 / 4 67 17 51
Fax: +32 (0) 2 / 4 67 17 45
e mail: infoautomation@getronics.com
TELECON CO.
BULGARlA
4, A. Ljapchev Blvd.
BG-1756 Sofia
Phone: +359 92 / 97 44 05 8
Fax: +359 92 / 97 44 06 1
e mail: ——
AutoCont
CZECHIA
Control Systems s.r.o.
Nemocnicni 12
CZ-70200 Ostrava 2
Phone: +420 (0) 69 / 615 21 11
Fax: +420 (0) 69 / 615 21 12
e mail: ——
louis poulsen
DENMARK
industri & automation
Geminivej 32
DK-2670 Greve
Phone: +45 (0) 43 / 95 95 95
Fax: +45 (0) 43 / 95 95 91
e mail: lpia@lpmail.com
UTU Elektrotehnika AS
Pärnu mnt. 160i
EE-10621 Tallinn
Phone: +372 6 / 51 72 80
Fax: +372 6 / 51 72 88
e mail: utu@utu.ee
ESTONIA
ALFATRADE LTD.
MALTA
99 Paola Hill
Paola PLA 08
Phone: +356 / 697816
Fax: +356 / 697817
e mail: paul.licari@alfatrx.com
Getronics bv
NETHERLANDS
Control Systems
Donauweg 10
NL-1043 AJ-Amsterdam
Phone: +31 (0) 20 / 586 15 92
Fax: +31 (0) 20 / 586 19 27
e mail: infoautomation@getronics.com
Beijer Electronics AS
NORWAY
Teglverksveien 1
N-3002 Drammen
Phone: +47 (0) 32 / 24 30 00
Fax: +47 (0) 32 / 84 85 77
e mall: ——
MPL Technology SP.Z.o.o
POLAND
ul.Wroclawska 53
PL-30-011 Kraków
Phone: +48 (0) 12 / 632 28 85
Fax: +48 (0) 12 / 632 47 82
e mail: krakow@mpl.com.pl
Sirius Trading&Services srl ROMANIA
Bd. Ghica nr. 112, BI. 41
RO-72335 Bucaresti 2
Phone: +40 (0) 1 / 210 55 11
Fax: +40 (0) 1 / 210 55 11
e mail: sirius_t_s@fx.ro
URHO TUOMINEN OY
FINLAND
Hevoshaankatu 3
FIN-28600 Pori
Phone: +358 (0) 2 / 55 08 00
Fax: +358 (0) 2 / 55 088 41
e mall: ——
ACP AUTOCOMP a.s.
SLOVAKIA
Chalupkova 7
SK-81109 Bratislava
Phone: +421 (0) 7 592 22 54
Fax: +421 (0) 7 592 22 48
e mall: ——
UTECO A.B.E.E.
GREECE
5, Mavrogenous Str.
GR-18542 Piraeus
Phone: +30 (0) 1 / 42 10 050
Fax: +30 (0) 1 / 42 12 033
e mall: uteco@uteco.gr
lNEA d.o.o.
SLOVENlA
Ljubljanska 80
SI-1230 Dom z ale
Phone: +386 (0) 17 21 80 00
Fax: +386 (0) 17 24 16 72
e mail: inea@inea.si
ECONOTEC AG
SWITZERLAND
Postfach 282
CH-8309 Nürensdorf
Phone: +41 (0) 1 / 838 48 11
Fax: +41 (0) 1 / 838 48 12
e mall: ——
GTS
TURKEY
Darülaceze Cad. No. 43A KAT: 2
TR-80270 Okmeydani-Istanbul
Phone: +90 (0) 212 / 320 1640
Fax: +90 (0) 212 / 320 1649
e mall: ——
EURASIAN REPRESENTATIVES
MITSUBISHI ELECTRIC
RUSSIA
EUROPE B.V.
12/1 Goncharnaya St, suite 3C
RUS-109240 Moskow
Phone: +7 (0) 95 / 915-8624/02
Fax: +7 (0) 95 / 915-8603
e mall: ——
STC Drive Technique
RUSSIA
Poslannikov per., 9, str. 1
RUS-107005 Moskow
Phone: +7 (0) 95 / 786 21 00
Fax: +7 (0) 95 / 786 21 01
e mall: ——
JV-CSC Automation
UKRAINE
15, M. Raskovoyi St., Floor 10,
Office 1010
U-02002 Kiev
Phone: +380 (4) 4 / 238 83 16
Fax: +380 (4) 4 / 238 83 17
e-Mail: mkl@csc-a.kiev.ua
MIDDLE EAST REPRESENTATIVE
SHERF Motion Techn. LTD
ISRAEL
Rehov Hamerkava 19
IL-58851 Holon
Phone: +972 (0) 3 / 559 54 62
Fax: +972 (0) 3 / 556 01 82
e mall: ——
HEAD OFFICE: TOKYO BUILDING 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
BCN-A211508-005-A(1201)MEE Printed in Japan
Specifications subject to change without notice.