- No category
advertisement
Installation Instructions
for XLS-650K/XLB-650K/XLC-650K LED and Line Amp Kits
• Standard American Projectors
• Christie Projectors
• Cinemeccanica Projectors
• Kinoton Projectors
• Norelco AA2 Projectors
Mounting L Bracket**
TM
XLS/B*-650 Lamp
U.S. Patent No. 5,600,206
Worldwide Patents Pending
XLA-650 Line Amp
The XLS-650 LED exciter lamp replaces BXM and BXN exciter bulbs used in the following projectors:
Ballantine/Strong
Century R2, R3
RCA 1040/1050 (adapter required)
RCA 930/950 (Dual Bulb)
Simplex 5 Star, SH-1000, SH 1006
* The XLB-650 LED exciter lamp replaces BXM and BXN exciter bulbs and has the locking ring reversed (locking ring can be reversed in the field). The XLB-650 is used in the following projectors:
Christie/Universal Projector
Simplex SH-1200, SH-1226 (Dual Bulb)
** The Mounting L Bracket (supplied, in circle above) is secured to the XLA-650 Line
Amp with the supplied sheet metal screw, which replaces any of the three screws securing the XLA-650 cover. Mount the assembly to any suitable screw in the projector.
® Manufacturers of Products
TM
Installation Instructions
1. Insert TM into exciter lamp socket.
2. Connect photocell leads to TM line amplifier.
3. Connect output lines to cell inputs on cinema processor.
4. Connect jumper wires from lamp socket to power input of line amplifier.
5. Make sure TM is centered for maximum output.
6. Run 50% test tone loop and set preamp level.
WARNING!!
Do not look directly into light. May cause eye damage.
Christie/Universal Soundheads
XLB-650K LED and Line Amp Kit
Route Photocell wires through holes in casting and around back of sound head.
Photocell
TM
Line Amp
XLA-650
4-12VAC
5-16VDC
POWER
OUTPUTS PHOTOCELL
E L+ L- R+ RC L R
Exciter Lamp
Power
4-12VAC
5-16VDC
Photocell
Blk
Red
Grn
Cinema Processor
Note: to reduce hum, tie one side of exciter lamp power supply to projector case.
Cinemeccanica Soundheads (BXM Lamp)
XLC-650K LED and Line Amp Kit
In order to install TM in Cinemeccanica soundheads you will need the newer style exciter lamp housing. Line amp gain is set for a boosted 16kHz response (A-jumper), internally. The wiring is the same as other installation procedures.
Century/Simplex/RCA Soundheads
XLS-650K LED and Line Amp Kit
*
Exciter Lamp
Power
4-12VAC
5-16VDC
Photocell
Route Power wires through holes in casting and around back of sound head.
Photocell
TM
Line Amp
XLA-650
4-12VAC
5-16VDC
POWER
OUTPUTS PHOTOCELL
E L+ L- R+ RC L R
Blk
Red
Grn
To Cinema Processor
Note: to reduce hum, tie one side of exciter lamp power supply to projector case.
* Certain soundheads may have their exciter lamp socket reversed. If this is the case, rotate the mounting flange on the bottom of the TM 180 degrees and reattach by means of the other three tapped mounting holes.
* RCA projectors require adapter ring.
Clearance Warning - Simplex Soundheads
If clearance is very close, TM lens could be scratched. Follow instructions in illustration below to increase clearance space.
uc ks
Loosen three screws
Slide left
Tighten screws
Lamp
Mounting
B r a c k e t
B r a c k e t
Mounting
Plate
Loosen three screws
Slide left
Tighten screws
Troubleshooting
Hum
• Four conductors and a shield must be used from the TM line amp to the cinema processor. Use either a pair of two-conductor shielded cables or a four-conductor shielded cable (Belden 8404 or equivalent).
A single two-conductor shielded cable will cause hum.
• Under some conditions, it may be necessary to ground one side of the exciter power supply to the projector frame to avoid hum. Proper grounding of soundhead is required.
• Stray ambient light could cause hum or noise. It may be necessary to adjust room light to minimize hum.
Specifications
XLS-650/XLB-650/XLC-650 LED Lamp
Input voltage: 4-12 VAC; 5-16 VDC 50/60Hz
Input current: 300ma @ 7VDC
Light source: Red LED @ 660nm
XLA-650 Line Amplifier
Input voltage: 4-12 VAC; 5-16 VDC 50/60Hz
Input current: 100ma @ 7VDC
Light source: 3mv RMS -50dbm with 200 ohm preamp load
Q u a l i t y C i n e m a P r o d u c t s
Ultra ★ Stereo Labs, Inc., 181 Bonetti Drive, San Luis Obispo, CA 93401 USA
Telephone 805.549.0161 • FAX 805.549.0163 • e-mail [email protected]
5/1/99
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project