- No category
advertisement
RoHS Compliant
USB-Disk ModuleⅡPlus
Product Specifications
March 23, 2015
Version 1.6
Apacer Technology Inc.
1F, No.32, Zhongcheng Rd., Tucheng Dist., New Taipei City, Taiwan
Tel: +886-2-2267-8000 Fax: +886-2-2267-2261 www.apacer.com http://www.apacer.com http://www.apacer.com
FEATURES:
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
USB2.0 High-Speed and USB1.1 Full-
Speed compatible interface
Capacity
–
4, 8, 16, 32, 64 GB
Performance*
–
Sustained read: 33 MB/s
–
Sustained write: 16 MB/s
Intelligent USB Module
–
Implements dynamic wear-leveling algorithms to substantially increase longevity of flash media
–
BCH (24 bit) Error Detection Code/Error
Correction Code (EDC/ECC)
–
Intrinsic data integrity after power loss
–
Wear leveling algorithm that provides more reliable data storage over an extended period
Extended Data Protection (Optional)
–
Write protection setting by jumper for prevention of data overwrites.
NAND Flash Type: MLC
MTBF
–
Approximately greater than 3.29 x 10
6 hours
Support Ready Boost for Windows Vista
Support boot-up function for OS
–
Windows XP Embedded
–
Windows CE
–
Linux
Temperature ranges
–
Operation:
Standa rd: 0°C to 70°C
Extended: -40°C to +85°C
–
Storage: -40°C to 1 00°C
Power consumption (typical)*
–
Active mode: 165 mA
–
Sleep mode: 450 µA
–
Operating voltage: 5V (with a certain percentage of tolerance)
Connector
–
10-pin (2x5) female header
RoHS Compliant
Support Non-Removable Setting
*The values addressed in Performance and Power consumption are typical and may vary from settings and platforms.
1
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
Table of Contents
1. General Description .............................................................................. 3
1.1 Performance-optimized Controller ....................................................................................................... 3
1.1.1 Power Management Unit (PMU) ................................................................................................... 3
1.1.2 SRAM Buffer ................................................................................................................................. 3
1.1.3 Error Correction Code (ECC) ........................................................................................................ 3
1.1.4 Wear-Leveling ............................................................................................................................... 3
1.1.5 Write Protection Mode (Optional) ................................................................................................. 3
2. Functional Block Diagram .................................................................... 4
3. Pin Assignment ..................................................................................... 5
3.1 Type A, Type B, and Type C ............................................................................................................... 5
3.2 Type D﹙STD﹚ ................................................................................................................................... 6
4. Performance & Reliability Specifications ............................................ 7
4.1 Capacity Specifications ....................................................................................................................... 7
4.2 Performance Specifications ................................................................................................................. 7
4.3 Environmental Specifications .............................................................................................................. 7
4.4 MTBF ................................................................................................................................................... 8
5. Electrical Specification ........................................................................ 9
5.1 AC Characteristics ............................................................................................................................... 9
6. Physical Dimension ............................................................................. 10
6.1 Horizontal Design .............................................................................................................................. 10
6.1.1 Type A (STD 90D) ...................................................................................................................... 10
6.1.2 Type B (STD 90D-MH) ............................................................................................................... 11
6.1.3 Type C (STD 90D-MS) ............................................................................................................... 12
6.2 Vertical Design .................................................................................................................................. 13
6.2.1 Type D (STD 180D) .................................................................................................................... 13
7. Product Ordering Information ............................................................ 14
7.1 Product Code Designations ............................................................................................................... 14
7.2 Valid Combinations ............................................................................................................................ 15
2
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
1. General Description
Apacer’s USB-Disk Module (UDM) is a high performance, embedded solid state drive (SSD) designed to replace a conventional IDE hard disk drive. UDM SSD can be plugged into a standard Embedded USB connector commonly found in desktops, portable PC systems and industrial PC systems. This product is well suited for embedded flash storage applications offering new and expanded functionality as well as more cost-effective designs, better performance and increased reliability.
This UDM solid state drive is resistant to shock and vibration and compatible with widely used operating systems such as Windows CE, Windows XP Embedded, and Linux. In terms of suitability, it comes in various dimensions to multiple embedded usages.
1.1 Performance-optimized Controller
The heart of an UDM is the USB controller, which translates standard USB signals into the data and controls of the flash media. This proprietary USB controller is specifically designed to attain high data throughput from host to flash.
1.1.1 Power Management Unit (PMU)
The power management unit (PMU) controls the power consumption of the UDM. It can dramatically extend product battery life by leaving the idle part of the circuitry into sleep mode. The PMU has zero wake-up latency.
1.1.2 SRAM Buffer
The SRAM buffer is a key contributor to the USB controller performance. It optimizes data writes to the flash.
1.1.3 Error Correction Code (ECC)
The UDM uses BCH Error Detection Code (EDC) and Error Correction Code (ECC) algorithms which correct up to 24 random single-bit errors for each 1024-byte block of data depending on spare area of flash memory. High performance is achieved through hardware-based error detection and correction.
1.1.4 Wear-Leveling
Flash memory can be erased a limited number of times, This number is called the erase cycle limit, or write endurance limit, The erase cycle limit applies to each individual erase block in the flash device.
In a typical application, and especially if a file system is used, specific pages are constantly updated (e.g., the page that contains the FAT, registry, etc.). Without any special handling, these pages would wear out more rapidly than other pages, reducing the lifetime of the entire flash.
To overcome this inherent deficiency,
Apacer’s USB-Disk Module (UDM) uses wear-leveling algorithm.
This wear-leveling algorithm ensures that consecutive writes of a specific sector are not written physically to the same page in the flash. This spreads flash media usage evenly across all pages, thereby maximizing flash lifetime.
The wear-leveling mechanism provides write/erase cycles for reliable data storage over an extended period.
1.1.5 Write Protection Mode (Optional)
When the device is configured to the Write-Protection mode, it enhances the data security and protection.
This feature prevents the stored data from inadvertent system writes or erases, and viruses.
3
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
2. Functional Block Diagram
The USB-Disk Module (UDM) contains a controller, embedded firmware, and Flash Media with a female connector. The UDM interfaces with the host system allowing data to be written to and read from the
Flash Media.
Host
USB Interface
Flash
Management
Controller
Flash
Media
Flash
Media
Figure 2-1
Functional block diagram
4
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
3. Pin Assignment
This chapter provides the information on the pin assignments and signal descriptions.
3.1 Type A, Type B, and Type C
Table 3-1
Pin Assignment of the 10-pin configuration in Type A, Type B, and Type C.
Pin
5
7
1
3
9
Signal
+5V
USB D-
USB D+
GND
Key (Blocked)
Pin
6
8
2
4
10
Signal
N.C
N.C
N.C
N.C
N.C
5
© 2015 Apacer Technology, Inc. Rev. 1.6
3.2 Type D﹙STD﹚
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
Table 3-2
Pin Assignment of the 10-pin configuration in Type D (STD)
Pin
1
3
5
7
9
Signal
+5V
USB D-
USB D+
GND
Key (Blocked)
Pin
2
4
6
8
10
Signal
+5V
N.C
N.C
GND
GND
6
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
4. Performance & Reliability Specifications
4.1 Capacity Specifications
The USB-Disk Module product family is available as below table matrix.
Table 4-1
Capacity Specification
Capacity Total Bytes
4GB
8GB
4,001,382,400
8,011,153,408
16GB 16,030,662,656
32GB 32,061,325,312
64GB 64,139,362,304
Note: Total user bytes may vary depending on file system in use.
4.2 Performance Specifications
Capacity
Table 4-2
Performance Specifications
4 GB
Performance
Sustained read (MB/s)
32
Sustained write (MB/s)
10
Note: results may vary depending on flash configurations.
8 GB
32
10
16 GB
33
14
32 GB
33
16
64 GB
33
16
4.3 Environmental Specifications
Environmental specification of the USB-Disk Module (UDM) product family which follows the MIL-STD-
810F standards is available as shown in Table 4-3.
Table 4-3
Environmental Specifications
Operation
0℃~70℃(standard) ; -40℃~85℃(extended) ;
Temperature
Storage -40°C to 100°C
Vibration
Sine wave 10 Hz to 500 Hz, 50 m/s
2
, 3 axes (IEC 68-2-6, non-operating)
Shock
EMC
Half sine wave 50G, 6 axes, 18 times (IEC 68-2-27, non-operating)
FCC, CE
7
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
4.4 MTBF
Mean Time Between Failures (MTBF) is predicted based on reliability data for the individual components in this device. The measurement assumes that device failure rate can be generated by the sum of failure rates in each component and a steady state failure rate can be predicated as equal to or greater than
4.20 x 10
6
hours.
Notes about the MTBF: The MTBF is predicated and calculated based on
“Bellcore Analysis Method 1”. number of component types device failure rate at steady state quantity of I type component failure rate for I type component at steady state device environment factor
8
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
5. Electrical Specification
Caution: Absolute Maximum Stress Ratings
– Applied conditions greater than those listed under
“Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device reliability.
Table 5-1
Operating Range
Range Ambient Temperature Voltage
Standard 0°C to 70°C
4.5-5.5V
Extended -40°C ~85°C
Table 5-2
Absolute maximum power pin stress ratings
Parameter
Power Supply Input
Voltage on any pin except VDD with respect to GND
Symbol
VDD- VSS
VIN
Min
-0.3
Max
5.5
Unit
V
–ss – 0.3 VDD +0.3
V
5.1 AC Characteristics
Parameter
Rise Time
Table 5-3
AC Characteristics Full Speed
Symbol Min Typ
T
FR
4
─
Max
20
Unit
ns
T
FF
4
─
20 ns Fall Time
Differential Rise and
Fall Time Matching
Driver Output
Resistance
T
FRFM
Z
DRV
90
28
─
111.11
44
%
Ω
Parameter
Rise Time (10%~90%)
Table 5-4
AC Characteristics High Speed
Symbol Min Typ
T
HSR
500
─
Max
─
T
HSF
500
─ ─
Fall Time (10%~90%)
Driver Output
Resistance
Z
HSDRV
40.5
─
49.5
Unit
ps ps
Ω
9
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
6. Physical Dimension
6.1 Horizontal Design
6.1.1 Type A
(STD 90D)
Standard 90 degree
Length 28.8
mm
Width 26.65
mm
Height (Max)
10.5 mm
Unit:
㎜
Tolerance:
±
0.2
10
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
6.1.2 Type B
(STD 90D-MH)
Standard 90 Degree Mounting Header
Length 37.8
mm
Width 26.65
mm
Height (Max)
10.5 mm
Unit:
㎜
Tolerance:
±
0.2
11
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
6.1.3 Type C
(STD 90D-MS)
Standard 90 Degree Mounting Screw
Length 37.8
mm
Width 26.65
mm
Height (Max)
10.5 mm
Unit:
㎜
Tolerance:
±
0.2
12
© 2015 Apacer Technology, Inc. Rev. 1.6
6.2 Vertical Design
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
6.2.1 Type D
(STD 180D)
Standard 180 Degree
Length 37.3
mm
Width 26.65
mm
Height (Max)
8.5 mm
Unit:
㎜
Tolerance:
±
0.2
13
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
7. Product Ordering Information
7.1 Product Code Designations
A P
– U M x x x x X X X X X – XX XX CM
Flash Type: CM: Micron MLC
Option:
RB: Ready Boost
WP: Write Protection
NR: Non-Removable
MS: Mounting Screw
MH: Mounting Header
S: Halogen-free Compliant
R: RoHS Compliant
Temperature:
C: Commercial Temperature
E: Extended Temperature
PCB version
Dimension
1 = 90D STD
2 = 180D STD
Solution version
Capacities:
004G = 4GB
008G = 8GB
016G = 16GB
032G = 32GB
064G = 64GB
Model Name
Apacer Product Code
14
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
7.2 Valid Combinations
7.2.1 Type A
(STD 90D)
Standard 90 degree
Capacity Standard P/N Extended P/N
4GB
8GB
16GB
AP-UM004GR13CS-CM
AP-UM008GR13CS-CM
AP-UM016GR13CS-CM
32GB AP-UM032GR13CS-CM
64GB AP-UM064GR13CS-CM
7.2.2 Type B
(STD 90D-MH)
Standard 90 degree Mounting Header
Capacity Standard P/N
4GB
8GB
16GB
32GB
AP-UM004GT13ES-CM
AP-UM008GT13ES-CM
AP-UM016GT13ES-CM
AP-UM032GT13ES-CM
AP-UM064GT13ES-CM
Extended P/N
AP-UM004GR13CS-MHCM AP-UM004GT13ES-MHCM
AP-UM008GR13CS-MHCM AP-UM008GT13ES-MHCM
AP-UM016GR13CS-MHCM AP-UM016GT13ES-MHCM
AP-UM032GR13CS-MHCM AP-UM032GT13ES-MHCM
64GB AP-UM064GR13CS-MHCM AP-UM064GT13ES-MHCM
7.2.3 Type C
(STD 90D-MS)
Standard 90 degree Mounting Screw
Capacity Standard P/N Extended P/N
4GB
8GB
16GB
32GB
AP-UM004GR13CS-MSCM AP-UM004GT13ES-MSCM
AP-UM008GR13CS-MSCM AP-UM008GT13ES-MSCM
AP-UM016GR13CS-MSCM AP-UM016GT13ES-MSCM
AP-UM032GR13CS-MSCM AP-UM032GT13ES-MSCM
64GB AP-UM064GR13CS-MSCM AP-UM064GT13ES-MSCM
7.2.4 Type D
(STD 180D)
Standard 180 degree
Capacity Standard P/N Extended P/N
4GB
8GB
16GB
32GB
64GB
AP-UM004GR23CS-CM
AP-UM008GR23CS-CM
AP-UM016GR23CS-CM
AP-UM032GR23CS-CM
AP-UM064GR23CS-CM
AP-UM004GT23ES-CM
AP-UM008GT23ES-CM
AP-UM016GT23ES-CM
AP-UM032GT23ES-CM
AP-UM064GT23ES-CM
15
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
7.2.1 Type A
(STD 90D)
– NR
Standard 90 degree
Capacity Standard P/N Extended P/N
4GB
8GB
16GB
32GB
AP-UM004GR13CS-NRCM
AP-UM008GR13CS-NRCM
AP-UM016GR13CS-NRCM
AP-UM032GR13CS-NRCM
64GB AP-UM064GR13CS-NRCM
7.2.2 Type B
(STD 90D-MH)
– NR
Standard 90 degree Mounting Header
Capacity Standard P/N
4GB
8GB
16GB
AP-UM004GT13ES-NRCM
AP-UM008GT13ES-NRCM
AP-UM016GT13ES-NRCM
AP-UM032GT13ES-NRCM
AP-UM064GT13ES-NRCM
Extended P/N
AP-UM004GR13CS-MHNRCM AP-UM004GT13ES-MHNRCM
AP-UM008GR13CS-MHNRCM AP-UM008GT13ES-MHNRCM
AP-UM016GR13CS-MHNRCM AP-UM016GT13ES-MHNRCM
32GB AP-UM032GR13CS-MHNRCM AP-UM032GT13ES-MHNRCM
64GB
Capacity
AP-UM064GR13CS-MHNRCM AP-UM064GT13ES-MHNRCM
7.2.3 Type C
(STD 90D-MS)
– NR
Standard 90 degree Mounting Screw
Standard P/N Extended P/N
4GB
8GB
16GB
32GB
AP-UM004GR13CS-MSNRCM
AP-UM008GR13CS-MSNRCM
AP-UM016GR13CS-MSNRCM
AP-UM032GR13CS-MSNRCM
64GB AP-UM064GR13CS-MSNRCM
7.2.4 Type D
(STD 180D)
– NR
Standard 180 degree
Capacity Standard P/N
AP-UM004GT13ES-MSNRCM
AP-UM008GT13ES-MSNRCM
AP-UM016GT13ES-MSNRCM
AP-UM032GT13ES-MSNRCM
AP-UM064GT13ES-MSNRCM
Extended P/N
4GB
8GB
16GB
32GB
64GB
AP-UM004GR23CS-NRCM
AP-UM008GR23CS-NRCM
AP-UM016GR23CS-NRCM
AP-UM032GR23CS-NRCM
AP-UM064GR23CS-NRCM
AP-UM004GT23ES-NRCM
AP-UM008GT23ES-NRCM
AP-UM016GT23ES-NRCM
AP-UM032GT23ES-NRCM
AP-UM064GT23ES-NRCM
16
© 2015 Apacer Technology, Inc. Rev. 1.6
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
Revision History
Revision Description
1.0 Official Release
1.1
1.2
1.3
Added MTBF section
Updated power consumption
Updated contact phone number of Apacer office in America
1.4
1.5
1.6
Updated product ordering information
Added extended temperature support
Revised extended P/N : 7.2.2 , 7.2.3, 7.2.4
Date
December 13, 2011
May 10, 2012
June 29, 2012
August 30, 2012
February 3, 2015
March 10, 2015
March 23, 2015
17
© 2015 Apacer Technology, Inc. Rev. 1.6
Taiwan (Headquarters)
USB-Disk ModuleⅡPlus
AP-UMxxxxXXXXX-XXXXCM
Global Presence
U.S.A.
Japan
Europe
China
India
Apacer Technology Inc.
1F., No.32, Zhongcheng Rd., Tucheng Dist.,
New Taipei City 236, Taiwan R.O.C.
Tel: 886-2-2267-8000
Fax: 886-2-2267-2261 [email protected]
Apacer Memory America, Inc.
386 Fairview Way, Suite102,
Milpitas, CA 95035
Tel: 1-408-518-8699
Fax: 1-408-935-9611 [email protected]
Apacer Technology Corp.
5F, Matsura Bldg., Shiba, Minato-Ku
Tokyo, 105-0014, Japan
Tel: 81-3-5419-2668
Fax: 81-3-5419-0018 [email protected]
Apacer Technology B.V.
Science Park Eindhoven 5051 5692 EB Son,
The Netherlands
Tel: 31-40-267-0000
Fax: 31-40-267-0000#6199 [email protected]
Apacer Electronic (Shanghai) Co., Ltd
1301, No.251,Xiaomuqiao Road, Shanghai,
200032, China
Tel: 86-21-5529-0222
Fax: 86-21-5206-6939 [email protected]
Apacer Technologies Pvt. Ltd.
# 535, 1st Floor, 8th cross, JP Nagar 3rd Phase,
Bangalore
– 560078, India
Tel: 91-80-4152-9061 [email protected]
18
© 2015 Apacer Technology, Inc. Rev. 1.6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 1.1 Performance-optimized Controller
- 4 1.1.1 Power Management Unit (PMU)
- 4 1.1.2 SRAM Buffer
- 4 1.1.3 Error Correction Code (ECC)
- 4 1.1.4 Wear-Leveling
- 4 1.1.5 Write Protection Mode (Optional)
- 6 3.1 Type A, Type B, and Type C
- 7 3.2 Type D﹙STD
- 8 4.1 Capacity Specifications
- 8 4.2 Performance Specifications
- 8 4.3 Environmental Specifications
- 9 4.4 MTBF
- 10 5.1 AC Characteristics
- 11 6.1 Horizontal Design
- 11 6.1.1 Type A (STD 90D)
- 12 6.1.2 Type B (STD 90D-MH)
- 13 6.1.3 Type C (STD 90D-MS)
- 14 6.2 Vertical Design
- 14 6.2.1 Type D (STD 180D)
- 15 7.1 Product Code Designations
- 16 7.2 Valid Combinations