Yamaha 7000 Owner`s manual

POWER AMPLIFIER
Owner’s Manual
E
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The above warning is located on the top
of the unit
IMPORTANT SAFETY INSTRUCTIONS
1
2
3
4
5
6
7
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete
outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
11
12
13
14
receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by
the manufacturer.
Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED
IMPORTANT. The wires in this mains lead are coloured in accordance
with the following code:
GREEN-AND-YELLOW : EARTH
BLUE
: NEUTRAL
BROWN
: LIVE
As the colours of the wires in the mains lead of this apparatus may not
correspond with the coloured markings identifying the terminals in
your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected
to the terminal in the plug which is marked by the letter E or by the
safety earth symbol
or colored GREEN or GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.
2
(3 wires)
-
1
+
+
(-)
1
-
(+)
BRIDGE
This mark indicates a dangerous electrically live terminal.
When connecting an external wire to this terminal, it is
necessary either to have “a person who have received
appropriate guidance on handling” make the connection or to
use leads or a cord that have been manufactured in such a way
that the connection can be made simply and without problem.
Precautions
— For safe operation —
WARNING
●
Installation
●
●
●
●
●
Connect this unit’s power cord only to an AC outlet of the type
stated in this Owner’s Manual or as marked on the unit. Failure
to do so is a fire and electrical shock hazard.
Do not allow water to enter this unit or allow the unit to
become wet. Fire or electrical shock may result.
Do not place a container with liquid or small metal objects on
top of this unit. Liquid or metal objects inside this unit are a
fire and electrical shock hazard.
Do not place heavy objects, including this unit, on top of the
power cord. A damaged power cord is a fire and electrical
shock hazard. In particular, be careful not to place heavy
objects on a power cord covered by a carpet.
Be sure to connect to an appropriate outlet with a protective
grounding connection. Improper grounding can result in electrical shock.
●
●
In case an abnormality occurs during operation
●
●
●
Operation
●
●
Do not modify the unit. Doing so is a fire and electrical shock hazard.
If lightning begins to occur, turn off the power switch of the unit as
soon as possible, and unplug the power cable plug from the electrical outlet.
If there is a possibility of lightning, do not touch the power cable
plug if it is still connected. Doing so may be an electrical shock
hazard.
Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a fire and electrical shock hazard.
Do not remove the unit’s cover. You could receive an electrical
shock. If you think internal inspection, maintenance, or repair is
necessary, contact your dealer.
If the power cord is damaged (i.e., cut or a bare wire is exposed),
ask your dealer for a replacement. Using the unit with a damaged
power cord is a fire and electrical shock hazard.
Should this unit be dropped or the cabinet be damaged, turn the
power switch off, remove the power plug from the AC outlet, and
contact your dealer. If you continue using the unit without heeding
this instruction, fire or electrical shock may result.
If you notice any abnormality, such as smoke, odor, or noise, or if
a foreign object or liquid gets inside the unit, turn it off immediately. Remove the power cord from the AC outlet. Consult your
dealer for repair. Using the unit in this condition is a fire and electrical shock hazard.
CAUTION
Installation
●
●
●
●
●
●
●
Keep this unit away from the following locations:
- Locations exposed to oil splashes or steam, such as near cooking stoves, humidifiers, etc.
- Unstable surfaces, such as a wobbly table or slope.
- Locations exposed to excessive heat, such as inside a car with
all the windows closed, or places that receive direct sunlight.
- Locations subject to excessive humidity or dust accumulation.
Do not place the power cord close to a heater. It may melt, causing
fire or electrical shock.
Hold the power cord plug when disconnecting it from an AC outlet. Never pull the cord. A damaged power cord is a potential fire
and electrical shock hazard.
Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard.
This unit has ventilation holes at the front and rear to prevent the
internal temperature rising too high. Do not block them. Blocked
ventilation holes are a fire hazard.
In particular, do not
- place the unit on its side or upside down,
- place the unit in any poorly-ventilated location such as a bookcase or closet (other than on the dedicated rack),
- cover the unit with a table cloth or place it on a carpet or bed.
Allow enough free space around the unit for normal ventilation.
This should be: 5 cm at the sides, 10 cm behind, and 10 cm above.
If the airflow is not adequate, the unit will heat up inside and may
cause a fire.
To mount several of these units in a standard EIA rack, refer to the
rack mounting instructions on page 11.
●
●
●
To relocate the unit, turn the power switch off, remove the power
plug from the AC outlet, and remove all connecting cables. Damaged cables may cause fire or electrical shock.
When setting up the product, make sure that the AC outlet you are
using is easily accessible. If some trouble or malfunction occurs,
immediately turn off the power switch and disconnect the plug
from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When
you are not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.
Do not place the device in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction.
Operation
●
●
●
●
●
Use only speaker cables when connecting speakers to amplifier
outputs. Using other types of cables is a fire hazard.
Turn off all musical instruments, audio equipment, and speakers
when connecting to this unit. Use the correct connecting cables
and connect as specified.
Always lower the volume control to minimum before turning on
the power to this unit. A sudden blast of sound may damage your
hearing.
Do not use this amplifier for any purpose other than driving loudspeakers.
If you know you will not use this unit for a long period of time,
such as when going on vacation, remove the power plug from the
AC outlet. Leaving it connected is a potential fire hazard.
3
— For correct operation —
Connector pin assignments
●
XLR-type connectors are wired as follows
Pin 1: ground; Pin 2: hot (+); Pin 3: cold (–).
Interference from Cell Phones
●
Use of a mobile phone near this unit may induce noise. If noise
occurs, move the phone further from the unit.
Always turn the power off when the amplifier is not in use.
Illustrations in this manual are for explanatory purposes only, and may not match the actual appearance of the product during operation.
Company names and product names used in this Owner's Manual are trademarks or registered trademarks of their respective owners.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
* This applies only to products (P7000S, P5000S) distributed by YAMAHA CORPORATION OF AMERICA.
4
Introduction
Thank you for your purchase of the YAMAHA P7000S, P5000S, P3500S or P2500S power amplifier.
These P-series amplifiers fully incorporate Yamaha’s renown technological expertise, and offer high
reliability, rock-solid stability, and superb acoustic characteristics—all in a trim, 2U-sized package.
Features
• With two types of input jacks (balanced XLR and balanced phone) and three types of output jacks
(Speakon, 5-way binding post, and phone), the P series is suitable for a wide variety of applications
and installed systems.
• The unit offers three operating modes: STEREO (where Channels A and B operate independently),
PARALLEL (where the unit outputs a mono source through twin amplifier systems), and BRIDGE
(where the unit operates as a single high-power amp).
• Each channel is equipped with an independent OFF/LOW CUT/SUBWOOFER switch—where
LOW CUT engages a high-pass filter, and SUBWOOFER engages a low-pass filter. With LOW CUT
or SUBWOOFER selected, you can adjust the cutoff frequency from 25 to 150 Hz.
• Each channel has its own SIGNAL and CLIP indicators.
• The PROTECTION indicator lights up—and sound output is automatically muted—whenever the
unit’s protective circuitry is operating. The TEMP indicator lights up if the unit is running hot.
• Variable-speed low-noise fans ensure high reliability.
This Owner’s Manual covers the four models: P7000S, P5000S, P3500S and P2500S power amplifiers. Please read through this manual carefully before beginning use, so that you will be able to take full
advantage of the amplifier’s superlative features and enjoy trouble-free operation for years to come.
After reading through the manual, please store it in a safe place.
Contents
Controls and Functions ..................................... 6
Front Panel .......................................................... 6
Rear Panel ........................................................... 7
Speaker Connections ........................................ 9
Speaker impedance ............................................. 9
Wiring ................................................................ 10
Rack Mounting ................................................ 11
Specifications .................................................. 12
General Specifications ....................................... 12
Block Diagram ................................................... 13
Dimensions ........................................................ 14
Current Draw ..................................................... 14
Troubleshooting ............................................... 15
5
Controls and Functions
■ Front Panel
2
8
1
4
3
57 6
1 POWER switch and indicator
8
How to install the security cover
(1) Use the supplied hex wrench to remove the four attachment screws from the amplifier.
(2) Adjust the security cover to the position of screw holes.
Fasten it into place using the same screws.
Press to toggle the power on or off. The POWER indicator
lights up green when the power is ON.
2 TEMP indicator
Lights up red if the heat sink temperature exceeds 85°C
(185°F).
3 PROTECTION indicator
Lights up red to indicate that protection is in effect. Specifically, lights up if the heat sink overheats, or if a DC voltage is
detected at the amplifier outputs. Also lights up for about three
seconds at time of power-on, as the amp gets ready to operate.
To provide protection, the unit will not output any sound from
the speakers while this indicator is lit up. When start-up is
completed or the problem is corrected, the indicator goes off
and normal operation resumes.
4 CLIP indicator
Lights up red when the output signal distortion on the corresponding channel rises above 1%—indicating that “clipping”
has occurred because the signal level is too high.
5 SIGNAL indicator
Lights up green when the corresponding channel’s output level
exceeds 2 Vrms (equivalent to 1/2 W into an 8 Ω load, or 1 W
into a 4 Ω load).
6 Volume control knobs
Each control knob adjusts the volume of the corresponding
channel, in 31 steps from –∞ dB to 0 dB.
NOTE:
If you wish to lock in the knob settings, you can fasten the supplied security cover over the knobs so that the settings will not
be disturbed.
6
indicator
7
Lights up yellow if the YS PROCESSING switch on the rear
panel is set ON. (See page 7.)
8 Air intakes
The amplifier uses forced-air cooling. The cooling fans draw
air in from the front and exhaust it through the rear. Please be
sure that you do not block the air intakes or exhaust vents.
NOTE:
The fans do not come on at initial power-on, but will switch on
automatically when the temperature of the heat sink rises above
50°C (122°F). The fan speed will then vary automatically as
the temperature changes.
■ Rear Panel
12
SUB
LOW CUT WOOFER OFF
5
SUB
OFF WOOFER LOW CUT
LOCK
LOCK
3
90
ON OFF
50
Hz
SPEAKERS
2
3
50
125
25
2
90
150
125
STEREO BRIDGE PARALLEL
FREQUENCY
25
Hz
150
FREQUENCY
INPUT
1+
12+
2-
+ 1+
- 1-
-
1
+
+
(-)
1
+
+
-
-
(+)
BRIDGE
43
1 FILTER switch and FREQUENCY adjustment knob
(One pair for each channel)
Use these controls to select the filter type and adjust the cutoff
frequency on each channel (A and B). You use the FILTER
switch to select the filter, as follows.
SUB
OFF WOOFER LOW CUT
OFF ...................... Do not use any filter.
SUBWOOFER..... Use a low-pass filter. The amplifier outputs
the frequencies that are lower than the cutoff set by the FREQUENCY adjustment
knob.
LOW CUT ........... Use a high-pass filter. You can use this setting to filter out unneeded low or subsonic
frequencies.
If you select SUBWOOFER or LOW CUT, you can then use
the FREQUENCY adjustment knob to adjust the cutoff frequency. The adjustment range is 25 Hz to 150 Hz.
Cutoff frequency
6
ON/OFF switch
2
If you set this switch ON, the amplifier adds low-frequency
compensation so as to enhance speaker output. The results (the
actual change in the low-frequency balance) will vary according to the speaker type. Note that this switch is effective only if
the FILTER switch is set to OFF.
NOTE:
This feature provides improved frequency reponse on speakers
such as the YAMAHA S112 and S115.
3 INPUT jacks (Channels A, B)
Two jack types are provided for each channel. Note that if you
are using BRIDGE or PARALLEL mode, only the Channel A
jacks are effective.
• XLR-3-31 jack
The XLR-3-31 input jacks are wired as shown below.
hot
ground
1
2
3
cold
• Phone jack
Phone jacks are wired as follows.
ring (cold)
25
to 150Hz
Hz
25Hz
Hz-150
NOTE:
If the amplifer is set to BRIDGE mode, only the switch and
knob for Channel A are effective. (The Channel B frequency
controls are disabled.)
sleeve
(ground)
tip (hot)
7
4 STEREO/PARALLEL/BRIDGE switch
Use this switch to select the operating mode.
• STEREO mode
Channels A and B operate independently (as with a conventional stereo amplifier). The Channel A input goes to the Channel A output jacks, and the Channel B input goes to the
Channel B output jacks.
• PARALLEL mode
The Channel A input signal is output through both the Channel
A and Channel B output jacks. The Channel B input jacks do
not function. Channel A and B volumes can be independently
adjusted.
• BRIDGE mode
The Channel A input signal is output from the BRIDGE output
jacks. To adjust the volume, you must use the Channel A volume control knob.
5 SPEAKER jacks
Neutrik NL4FC Speakon output connectors,
5-way binding post output jacks,
Phone output jacks
For minimum speaker impedenance values, see page 9.
6 GND terminal
This is a screw-type ground terminal. If you are having a problem with hum or noise, use this terminal to connect to ground
or to connect to the chassis of the mixer, preamp, or other
device in your system.
8
Speaker Connections
■ Speaker impedance
Speakers can be connected to the amplifier as shown below. Note that speaker impedance will vary according to the connection method and
the number of speakers. Please be sure that your speakers’ impedance is not less than the relevant minimum value indicated below.
Connection configurations for STEREO and
PARALLEL modes
Connection configurations for BRIDGE
mode
When using 5-way binding post output jacks
When using 5-way binding post output jacks
1
-
+
+
1
1
-
-
+
+
1
-
STEREO BRIDGE PARALLEL
STEREO BRIDGE PARALLEL
(-)
(-)
(+)
(+)
BRIDGE
BRIDGE
or
STEREO BRIDGE PARALLEL
Minimum
speaker
impedance:
4Ω
When using Speakon connector
LOCK
8Ω
4Ω
When using Speakon connector
SPEAKERS
LOCK
3
Minimum
speaker
impedance:
Minimum
speaker
impedance:
2
2
1+
12+
2-
+ 1+
- 1-
LOCK
3
3
+
+
-
SPEAKERS
LOCK
2
2
3
1+
12+
2-
+ 1+
- 1-
+
+
-
Minimum
speaker
impedance:
Minimum
speaker
impedance:
8Ω
4Ω
When using phone jack
LOCK
3
LOCK
2
+ 1+
- 1-
SPEAKERS
2
3
1+
12+
2-
+
+
-
Minimum
speaker
impedance:
4Ω
9
■ Wiring
5-way binding post
Speakon connector
(1) Turn off the POWER switch.
(2) Remove the cover attachment screws and remove the protective cover from the speaker terminals.
(1) Turn off the POWER switch.
(2) Insert the Neutrik NL4FC plugs into the Speakon connector on the rear of the amplifier, and turn clockwise to lock.
Neutrik NL4FC plugs
CHANNEL A
Screw
(3) Remove about 15 mm of insulation from the end of each
speaker cable, and pass the bare wire through the holes in
the appropriate speaker terminals. Tighten the terminals to
securely clamp the wires. Refer to page 9 for speaker
polarities.
STEREO or PARALLEL
BRIDGE
1+
A+
1+
1–
A–
1–
2+
B+
2+
2–
B–
2–
+
–
Neutrik NL4FC plugs
CHANNEL B
1+
B+
1–
B–
15mm
*
Phone jack
(1) Turn off the POWER switch.
(2) Insert the phone plug into the jack on the rear of the amplifier.
Speaker cable
* Actual size
Note to users in the USA:
Please use Class 3 wiring. (P7000S, P5000S)
Please use Class 2 wiring. (P3500S, P2500S)
Be sure that the bare wire ends do not jut out from the terminals and touch the chassis. The following shows how
the cable should look when correctly attached.
Bare wire
Chassis
(4) Reattach the protective cover over the speaker terminals.
10
Rack Mounting
Mounting in a standard EIA rack
If you are mounting multiple power amplifiers in a rack, be sure to install ventilation panel(s) as shown below. Also be sure to use metal brackets (one on each side) to support the rear of each amplifer.
Note: EIA stands for Electronic Industries Alliance.
Ventilation panel(s)
Use 1U-size blank panel(s).
44
480
Unit: mm
If mounting up to four amplifiers in
an open-backed rack
Install a ventilation panel as shown below.
Ventilation panel
(Attach to the front
or rear of the rack.)
When mounting five or more amplifiers in an open-backed rack, and
when mounting any number of
amplifiers in a close-backed rack
Install ventilation panels above and below each amplifier, as shown
below.
11
Specifications
■ General Specifications
Power Output Level (Rated Power)
1 kHz
THD + N = 1%
8 Ω/STEREO
20 Hz – 20 kHz
THD + N = 0.1%
1 kHz
20 ms non-clip
Power Bandwidth
Total Harmonic Distortion (THD + N)
20 Hz – 20 kHz, Half Power
Frequency Response
Intermodulation Distortion (IMD)
60 Hz:7 kHz, 4:1, Half Power
Channel Separation
Vol. max
Residual Noise Vol. min.
SN Ratio
Damping Factor
Input Sensitivity
Voltage Gain
Input Impedance
Controls
Connectors
Indicators
4 Ω/STEREO
8 Ω/BRIDGE
700 W × 2
650 W × 2 (European Model)
950 W × 2
1900 W × 1
P5000S
525 W × 2
750 W × 2
1500 W × 1
P3500S
390 W × 2
590 W × 2
1180 W × 1
P2500S
275 W × 2
390 W × 2
780 W × 1
500 W × 2
350 W × 2
250 W × 2
700 W × 2
1400 W × 1
450 W × 2
900 W × 1
310 W × 2
620 W × 1
1300 W × 2
1000 W × 2
2 Ω/STEREO
1600 W × 2
2600 W × 1
2000 W × 1
4 Ω/BRIDGE
3200 W × 1
Half Power
10 Hz – 40 kHz (THD + N = 0.5 %)
4 Ω – 8 Ω/STEREO
≤ 0.1 %
8 Ω/BRIDGE
RL = 8 Ω, Po = 1 W
+0 dB, –1.5 dB
20 Hz – 50 kHz
4 Ω – 8 Ω/STEREO
≤ 0.1 %
8 Ω/BRIDGE
Half Power RL = 8 Ω 1 kHz
≥ 70 dB
input 600 Ω shunt
20 Hz – 20 kHz (DIN AUDIO) ≤ –70 dBu
20 Hz – 20 kHz (DIN AUDIO)
104 dB
103 dB
102 dB
≥ 350
≥ 200
RL = 8 Ω, 1 kHz
RL = 8 Ω
+8.0 dBu
+6.4 dBu
+5.2 dBu
(1 kHz, THD + N = 1 %)
RL = 8 Ω
32 dB
30 kΩ/balanced, 15 kΩ/unbalanced
Front Panel
POWER switch (Push on/Push off)
Two 31-step Volume control knobs (one per ch)
Rear Panel
MODE switch (STEREO/PARALLEL/BRIDGE)
Two FILTER switches (SUBWOOFER/LOW CUT/OFF)
Two fc knobs (25 to 150 Hz, 12 dB/octave)
YS Processing switch (ON/OFF)
INPUT
XLR-3-31 jacks (one per ch)
1/4-inch TRS phone jacks (one per ch)
OUTPUT
Speakon jacks (one per ch)
5-way binding posts
1/4-inch phone jacks (one per ch)
POWER
× 1 (Green)
× 1 (Red)
PROTECTION
TEMP
× 1 (Red) (heatsink temp ≥ 85°C)
CLIP
SIGNAL
YS Processing
Load Protection
650 W × 2
1300 W × 1
100 dB
+3.6 dBu
× 2 (Red)
× 2 (Green)
× 1 (Yellow)
POWER switch ON/OFF muting
DC-fault power supply
shutdown
DC detection
Temp. detection (heat sink temp ≥ 90°C), VI limiter (RL ≤ 1 Ω)
Comp: THD ≥ 0.5 %
Amp. Protection
Limiter
Cooling
Power Requirements
Power Consumption
P7000S
750 W × 2
1100 W × 2
2200 W × 1
8 Ω/STEREO
4 Ω/STEREO
8 Ω/BRIDGE
Idling
Output power, 4 Ω
Dimensions (W × H × D)
Weight
Included Accessories
Dual variable-speed fan
Single variable-speed fan
120 V, 220 V – 240 V; 50 Hz/60 Hz
35 W
35 W
30 W
25 W
650 W
500 W
450 W
320 W
480 × 88 × 456 mm (18-7/8" × 3-7/16" × 17-15/16")
12.0 kg (26.5 lbs) 15.0 kg (33.1 lbs) 14.0 kg (30.9 lbs)
12.0 kg (26.5 lbs)
Security cover (with a hex wrench), Owner’s Manual
0 dBu=0.775 Vrms, Half Power=1/2 Power Output Level (Rated Power)
Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha
dealer.
European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 25A (P7000S, P5000S)/66A (P3500S)/68A (P2500S)
Conforms to Environments: E1, E2, E3 and E4
12
■ Block Diagram
P7000S, P5000S
P3500S, P2500S
HPF
LPF
BA
State variable
Active filter
CHANNEL A
ATT
Ach Power Amp
SPEAKERS
Limiter
3
OFF
Frequency
[25 Hz-150 Hz]
CHANNEL A
[BRIDGE]
[PARALLEL]
1+
SIGNAL
YAMAHA
SPEAKER
PROCESSING
2-
2
Temperature
Sensor
(Heat Sink)
ON
OFF
Protection
Circuit
1
PROTECTION
A+B BRIDGE
TEMP
YAMAHA
SPEAKER
PROCESSING
1
2+
CLIP
SIGNAL
CHANNEL B
2
12-
BA
State variable
Active filter
CHANNEL A
2+
INV
INPUT
1-
CLIP
CHANNEL B
ATT
OFF
PARALLEL
BRIDGE
STEREO
Bch Power Amp
CHANNEL B
1+
Limiter
3
LPF
HPF
Frequency
[25 Hz-150 Hz]
POWER
POWER CIRCUIT
POWER SW
+B
E
-B
+24
E
-24
FAN
13
■ Dimensions
Unit: mm
■ Current Draw
P7000S
Line Current (A)
100/120V
Power (W)
230/240V
In
Out
Thermal Dissipation
Dissipated
Btu/h
kcal/h
standby
0.08
0.04
5
0
5
17
4
idle
1.0
0.5
35
0
35
119
30
1/8 power
1/3 power
8Ω/ch
5.4
3.0
379
188
191
653
165
4Ω/ch
8.5
4.7
611
275
336
1150
289
8Ω/ch
12.8
7.0
918
500
418
1430
360
4Ω/ch
20.6
11.3
1481
733
748
2550
643
P5000S
Line Current (A)
100/120V
Power (W)
230/240V
In
Out
Thermal Dissipation
Dissipated
Btu/h
kcal/h
standby
0.08
0.04
5
0
5
17
4
idle
1.0
0.5
35
0
35
119
30
1/8 power
1/3 power
8Ω/ch
4.0
2.2
277
131
146
499
126
4Ω/ch
6.2
3.4
436
188
249
848
214
8Ω/ch
9.3
5.1
673
350
323
1100
278
4Ω/ch
14.7
8.1
1057
500
557
1900
479
P3500S
Line Current (A)
100/120V
In
Out
Thermal Dissipation
Dissipated
Btu/h
kcal/h
standby
0.08
0.04
5
0
5
17
4
idle
1.0
0.5
30
0
30
102
26
1/8 power
1/3 power
14
Power (W)
230/240V
8Ω/ch
3.2
1.7
227
98
130
443
112
4Ω/ch
5.0
2.8
378
148
231
787
198
8Ω/ch
7.3
4.0
551
260
291
993
250
4Ω/ch
12.2
6.7
917
393
524
1790
450
P2500S
Line Current (A)
100/120V
Power (W)
230/240V
In
Out
Thermal Dissipation
Dissipated
Btu/h
kcal/h
standby
0.08
0.04
5
0
5
17
4
idle
1.0
0.5
25
0
25
85
22
8Ω/ch
2.4
1.3
174
69
105
358
90
4Ω/ch
3.6
2.0
271
98
173
592
149
8Ω/ch
5.6
3.1
421
183
238
811
204
4Ω/ch
8.8
4.8
657
260
397
1350
341
1/8 power
1/3 power
1/8 power is typical of program material with occasional clipping. Refer to these figures for most applications.
1/3 power represents program material with extremely heavy clipping.
Test signal: Pink Noise, bandwidth limited from 22Hz to 22kHz
1W = 0.860kcal/h, 1BTU = 0.252kcal
Note that Line Voltage [V] x Line Current [A] = [VA], not equals to [W].
Inrush current
P7000S, P5000S: 11A (100V), 13A (120V), 25A (240V)
P3500S: 142A (100V), 170A (120V), 66A (240V)
P2500S: 103A (100V), 150A (120V), 68A (240V)
Troubleshooting
The following table lists the main causes of abnormal operation and the corrective measures required, as well as the protective circuit operation in each case.
Indicator(s)
Possible Cause
Remedy
Protection Circuit
There is a short at a speaker
terminal, amplifier terminal, or
wire.
Locate and correct the cause of
the short.
TEMP indicator lights.
The heat sink temperature has
exceeded 85°C (185°F).
Check the ventilation slots, and
provide better airflow around
the amplifier.
PROTECTION indicator lights.
The heat sink temperature has
exceeded 95°C (203°F).
Check the amplifier ventilation
The thermal protection circuit
conditions and take appropriate
operates to protect the power
measures to improve the
transistors.
airflow around the amplifier.
CLIP indicator lights.
The PC limiter circuit operates
Use a speaker system with an to protect the power
transistors.
impedance of at least 4 Ω
The amplifier load is excessive.
(STEREO/PARALLEL mode) or
8 Ω (BRIDGE mode).
The TEMP indicator lights up
to indicate temperature
warning.
P3500S, P2500S
Indicator(s)
PROTECTION indicator lights.
Possible Cause
Remedy
Protection Circuit
A DC voltage of ±2 V or greater
Consult your dealer or the
The relay operates to protect
was generated in the power
nearest Yamaha service center. the speaker system.
amplifier’s output circuit.
P7000S, P5000S
Indicator(s)
Power has been shut down. (All indicators
are off.)
Possible Cause
A DC voltage of ± 2 V or
greater was generated in the
power amplifier’s output circuit.
Remedy
Protection Circuit
The protection circuitry shut off
Consult your dealer or the
the power to protect the
nearest Yamaha service center.
speaker system.
15
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Tel: 714-522-9011
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col. San José
Insurgentes, Delegación Benito Juárez, México,
D.F., C.P. 03900
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,
CEP 04534-013 São Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
VENEZUELA
Yamaha Music Latin America, S.A.,
Sucursal Venezuela
C.C. Manzanares Plaza P4
Ofic. 0401- Manzanares-Baruta
Caracas Venezuela
Tel: 58-212-943-1877
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso No.7, Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
EUROPE
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: 01908-366700
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 044-387-8080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria (Central Eastern Europe Office)
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Branch Poland Office
ul. Wrotkowa 14 02-553 Warsaw, Poland
Tel: 022-500-2925
PA37
Para detalles sobre productos, contacte su tienda Yamaha más
cercana o el distribuidor autorizado que se lista debajo.
MALTA
ASIA
Olimpus Music Ltd.
The Emporium, Level 3, St. Louis Street Msida
MSD06
Tel: 02133-2144
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 400-051-7700
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, Netherlands
Tel: 0347-358 040
INDIA
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower A, Sector
47, Gurgaon- Sohna Road, Gurgaon, Haryana, India
Tel: 0124-485-3300
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activites Pariest,
77183 Croissy-Beaubourg, France
Tel: 01-64-61-4000
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
ITALY
Yamaha Music Europe GmbH, Branch Italy
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
KOREA
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas (Madrid), Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
Yamaha Music Europe GmbH Germany Norwegian Branch
Grini Næringspark 1, N-1361 Østerås, Norway
Tel: 67 16 78 00
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
AFRICA
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, UAE
Tel: +971-4-881-5868
MIDDLE EAST
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Maslak Meydan Sokak No:5 Spring Giz Plaza
Bağımsız Böl. No:3, 34398 Şişli İstanbul
Tel: +90-212-999-8010
CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
Yamaha Music (Malaysia) Sdn., Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
TAIWAN
Yamaha Music Europe GmbH, Tyskland – filial
Denmark
Generatorvej 8B, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
MALAYSIA
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: 65-6747-4374
Yamaha Music Europe GmbH Germany filial
Scandinavia
JA Wettergrensgata 1, Västra Frölunda, Sweden
Tel: +46 31 89 34 00
DENMARK
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
SINGAPORE
SWEDEN/FINLAND/ICELAND
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Yamaha Music & Electronics Taiwan Co.,Ltd.
3F, No.6, Section 2 Nan-Jing East Road, Taipei,
Taiwan R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
VIETNAM
Yamaha Music Vietnam Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
OTHER COUNTRIES
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, U.A.E
Tel: +971-4-881-5868
HEAD OFFICE Yamaha Corporation, Audio Products Sales and Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Yamaha Pro Audio global web site
http://www.yamahaproaudio.com/
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
C.S.G., Pro Audio Division
© 2003-2014 Yamaha Corporation
WB09700 409CRZCx.x-01G0
Printed in Indonesia