AMT6Trash Manual

Add to my manuals
16 Pages

advertisement

AMT6Trash Manual | Manualzz

Specifications Information and Repair Parts Manual

5585-B6, 5585-D6, 5585-H6, & 5587-Y6 x install, operate or maintain the product described. Protect yourself and others by observing all safety information. The Safety Instructions are contained in the General Operating Instructions. Failure to comply with the safety instructions accompanying this product could result in personal injury and/or property damage! Retain instructions for future reference. AMT reserves the right to discontinue any model or change specifications at any time without incurring any obligation.

©2011 American Machine & Tool Co., Inc. of PA, A Subsidiary of The Gorman-Rupp Company, All Rights Reserved.

Periodic maintenance and inspection is required on all pumps to insure proper operation. Unit must be clear of debris and sediment. Inspect for leaks and loose bolts. Failure to do so voids warranty.

6” Trash Pump

DESCRIPTION

2.

3.

4.

This trash pump is heavy duty, centrifugal, engine driven, self-priming (to 20 ft. lift), and transportable unit. Pump is equipped with precision lapped mechanical shaft seal to reduce the likelihood of leakage, and a clog resistant impeller capable of handling solids up to 3" in spherical diameter. Units are used to handle water containing stones, sticks, mud, and other solids (up to 20% by volume). O-ring sealed flange connection to provide leak-free low maintenance operation. Suction flange male NPT threaded for direct coupling to a standard NPS hose connector with rubber gasket. Liquid temperature range is 40º to 180º F (4º to 82º C). Maximum casing pressure if used in a flooded suction application is 50 psi. For use with nonflammable liquids that are compatible with pump component materials.

All models come equipped with a 12V electric starting system (battery

2. not included). A fully plumbed fuel tank is standard. Gas engine units are equipped with a 12 gallon marine grade plastic tank and diesel engine units have an 18 gallon aluminum tank. All units equipped with a digital tachometer/hour meter.

Pump and engine are mounted on an easy maintenance sliding frame assembly. Frame can be equipped with pneumatic tires, lighting system, support jacks, and a 2" diameter ball mount tongue hitch. A lunette ring is optional.

Tires, wheels, and lighting system meet DOT requirements and are supplied with certificate of origin and serial number. Check state and local requirements to register trailer/pump for highway towing.

SPECIFICATIONS

Suction Inlet…………………………………………………..6” NPT (male)

Discharge Outlet…………………………………….……..6” NPT (female)

Dimensions (overall)

Trailer Mounted…………………………………….……….9’L x 4’W x 5’H

Frame Mounted………………………………….……….6’L x 3’W x 3’3”H

Engine…………………………………….5585-B6: 27 HP B&S Vanguard

……………………………………………...5585-H6: 24HP Honda GX670

………….………………………….….5585-D6 27HP Daihatsu/Vanguard

…………………………………….5587-Y6: 23HP Yanmar 3TNM72-ASA

BASIC CONSTRUCTION

Cast aluminum with cast iron volute, stainless steel impeller, suction flange and discharge manifold. Viton silicon carbide shaft seal, Buna

O-rings, Buna/Neoprene suction check valve.

UNPACKING

Refer to Repair Parts Illustration and Repair Parts List to aid in identifying parts. Unpack and separate all pump components from shipping/packaging materials, making sure all parts are accounted for.

Retain all manuals for reference.

Package should contain:

1. Pump and engine completely assembled and mounted to frame.

Tongue packaged alone (not attached to frame).

Tail lights, side lights, wiring packaged alone.

Manuals included: Specifications information and repair parts manual, Operating Instructions/maintenance manual, tachometer/hour meter instruction/owner’s manual. instructions, engine mounting holes.

Position tongue under frame. Line up tongue mounting holes with holes in frame front and middle cross members.

Secure tongue to frame by installing four (4) mounting bolts 3. and nuts. Torque to 15-18 ft. lbs.

Light Kit Assembly Instructions

1.

2.

Position wiring harness under tongue, "Y" branch of harness should be under front tongue to frame connection.

Feed each branch wiring harness through hole in end of frame cross member and support loops at fender mounting bolts. Green/brown wire harness left side (looking from tongue end to pump end) yellow/brown wire harness right side. Pull harness snug (towards pump end of frame) while keeping "Y" at tongue connection.

3.

4.

5.

6.

7.

Remove support loops from tongue. Clip loops over plug end of wire harness. Install loops back into position supporting wire harness. Plug end should be free under coupler end of tongue. Install grounding eye under screw holding loop closest to tongue ball coupler.

Clip support loops over harness branches past "Y". Position loops on exposed end of tongue mounting bolts. Secure with a flange nut.

Install side lights onto frame side rails. Connect side light wire (wire may be inside lens) with brown wire in each branch harness. Secure connection with splice fitting or wire nut.

Feed taillight wires through middle hole of three holes on each end of pump end cross member.

Make taillight connections by pushing exposed stranded wire into appropriate hole in rear of taillight. Make certain

8.

9. taillight with license plate light is on the right side (looking from tongue).

Clip a support loop over the end of each wire harness.

Install license plate holder on right taillight studs. Install both taillight studs thru rear cross member holes. Position support clip on outer taillight stud. Secure taillights with flange nuts.

Frame Mounted Pump:

1. Unit shipped fully assembled.

NOTE: Follow all recommendations in General Operating Instruction and Maintenance Manual provided with this pump. In addition, follow the specific recommendations that follow.

INSTALLATION

Trailer Mounted Pump

ASSEMBLY

Trailer Mounted Pump

Tongue Assembly Instructions

1. Remove four mounting bolts and nuts inserted into tongue

To avoid trailer tipping, set rear trailer stabilizer jacks before removing trailer from vehicle hitch.

1. Always set trailer tongue stand and rear trailer stabilizer jacks before unhooking trailer hitch from vehicle tow ball.

1 8/2012 5585-250-00

Specifications Information and Repair Parts Manual x

6” Trash Pump

2.

Frame Mounted Pump

1.

Make sure pump and trailer are level and trailer wheels are blocked to prevent movement during operation.

Pump frame must be supported on a level firm surface.

Anchoring pump frame to support surface is required to prevent movement or tipping during operation. Mounting holes are provided on bottom flange of frame side rails. Allow

All Installations:

1. sufficient clearance around pump frame to perform routine maintenance.

2.

3.

4.

Suction line should be as short and direct as possible, have a constant slope up to the pump’s suction port, and line diameter must match suction port diameter. Use only reinforced non-collapsible hose on pump suction.

Check condition of suction hose gaskets before installation.

Weak, worn, leaking gaskets will allow an air leak at suction connection. If suction connection leaks air, the pump will not prime.

Supports must be used to carry the weight of the suction and discharge lines. The pump should not be used to support the entire weight of the suction and discharge lines.

Damage/breakage of pump ports may occur if lines are not supported.

If a check valve or collapsible hose is used on discharge, a means of venting air from the pump discharge manifold is required during the priming cycle. If air cannot escape from casing, the pump will not prime.

Lifting Bail

Pump frame is equipped with a lifting bail.

Lifting bail provides a convenient lifting point if positioning pump with a crane or similar equipment is necessary. Bail and lifting bolt assembly will support only the weight of frame/trailer, pump and driver.

Periodically re-torque lifting bolt assembly to 100 ft. lbs.

Remove suction and discharge lines and drain all liquid from pump before lifting.

Lift pump assembly and trailer only. Do not load piping, hoses or other equipment on trailer during lifting.

OPERATION

Starting Unit

1. Fill engine with oil according to engine manufacturer’s specifications listed in engine manual supplied.

2.

3.

Fill fuel tank with appropriate fuel for engine. Do not fill tank to the top allow at least an inch of airspace.

Fill pump casing with water through discharge manifold priming port. Casing must be full of water or pump will not prime.

Do not run pump dry as permanent damage to the mechanical seal will result.

4.

5.

6.

Start the engine, following instructions in engine manual.

Run engine at full throttle during priming cycle. Tachometer should indicate 3500 rpm or greater.

After pump has primed and is producing full flow, engine

7. speed should be regulated to produce desired pump performance level. Under high lift and/or low discharge head conditions, engine speed should be decreased to retard cavitation. This will extend pump, seal, and engine service life.

Yanmar diesel engine: Maximum operating speed, after full prime, is 3200 rpm.

5585-250-00 2

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

Do not operate pump unattended. Shaft seal damage will occur if prime is lost or if flow is insufficient to keep the shaft seal cool.

Refueling Tank

1.

2.

3.

Allow unit to cool before adding fuel to tank.

Remove tank cap.

Add fuel through fill neck. Watch fuel level gauge during filling and stop adding fuel when the gauge indicates full. Do

4. not overfill tank, allow an inch or two of airspace from fuel level to top of tank.

Install tank cap. Rotate clockwise until it hits internal stop indicating that it is sealed.

Pump End Drain

Pump end is equipped with an NPT drain port. The port is located on the pump adapter plate (Ref. No. C28) at the 6 o’clock position. The elbow (Ref. No. C30) is installed in the port to direct the liquid down through frame. The indented hex pipe plug (Ref. No. C31) is installed in elbow. Use a 9/16" L-hex wrench to remove plug. A ball valve and length of pipe or hose (not supplied) may be installed to direct the drain liquid away from the pump.

ALWAYS DRAIN LIQUID:

1.

2.

3.

After pumping operation is complete if freezing temperatures may be experienced.

Before transporting pump.

Before lifting pump.

Seal Wash Ports

These units are equipped with provisions for the addition of a seal wash hose. To extend seal life or when pumping water containing abrasive sediment or when a buildup of material on the shaft seal is encountered, a seal wash may increase seal life. The pump adapter plate is equipped with two 1/8" NPT tapped ports; one at the (high pressure volute discharge) 10 o’clock position on adapter face and one on top of the locating boss (low pressure seal cavity).

NOTE: Fittings and hose must be compatible with liquid pumped, liquid temperature, and rated for maximum discharge pressure in the installation.

NOTE: Addition of seal wash hose may affect priming performance.

After installing seal wash hose monitor length of time required to reach full prime.

Standard Installation:

Remove 1/8" NPT plugs (Ref. No. C29). Install appropriate fittings and hose between the two ports.

Abrasive Installation:

Remove 1/8" NPT plugs. Install appropriate fittings and hose between the two ports. The installation of an in-line abrasives separator is recommended. Contact appropriate manufacturer for details.

Clean Water Injection Installation:

Remove 1/8" NPT pipe plug from low pressure port. Connect external clean water source line to low pressure port of adapter with appropriate hose and fitting. Incoming pressure must be at least 10 psi greater than seal cavity pressure. A check valve is recommended to prevent back flow.

Transport Trailer

Pump supplied with trailer gear is for off road use only as shipped.

Trailer registration for use on public roads is the responsibility of the owner. A Manufacturer’s Certificate of Origin listing the Vehicle

Identification Number (VIN) is included with the trailer. Trailer registration requirements are regulated by each state and local government. Contact your State Department of Motor Vehicles or

Department of Transportation for information and guidance on licensing or titling the trailer/pump for towing on public roads in your state.

8/2012

Specifications Information and Repair Parts Manual x

6” Trash Pump

Ball Coupling Adjustment:

1.

2.

Install coupling over correct size trailer hitch mating ball and push down on handle until trigger locks in slot.

Pull up and down on tongue to ensure ball fits snug in coupler. There should be no play between coupler and ball.

3. Tighten adjustment nut, located on bottom of coupler opposite the handle, to take up any excessive play.

NOTE: If nut is too tight, the handle will not lock into position.

Towing Safety and Operational Guidelines:

Follow all safety and operational rules listed in the following section:

1.

2.

3.

4.

5.

Make sure vehicle is capable of towing the load. Make sure vehicle hitch is rated for the load.

Make sure the trailer coupler and hitch ball are the same sizes and rated for the load.

Make sure trailer coupler is correctly and safely connected to hitch ball. Coupler handle trigger must be positively locked. Install lock pin (not provided) to ensure trigger stays locked during towing.

Be sure to use safety chains supplied with trailer. Safety chains should be attached to towing vehicle at the same length on both sides and should not drag on the ground.

Never overload trailer. Trailer is rated to carry pump, pump frame and a full load of fuel. Loading other items on the trailer may cause GVW to exceed trailer rating.

Maximum safe highway towing speed is 45 mph. Never allow passengers on the trailer.

6.

7.

8.

Check all lights for proper operation before each use.

Check tires for wear and proper inflation before each use.

Inflate to psi rating on tire.

Check safety chains for wear and solid connection to trailer frame.

MAINTENANCE

Sliding Engine Sled Operation

Refer to Repair Parts pages.

Disconnect spark plug wires and battery to prevent accidental starting.

NOTE: Drain pump casing (Ref. No. C5) by removing plug (Ref. No.

C31). Also drain discharge line, and suction line of all liquid before sliding engine sled.

1.

To access impeller/seal plate area:

2.

Loosen six 1/2-13 nuts (Ref. No. C47) that are pressing clamp angle to sled.

3.

Remove three 1/2-13x1-3/4" cap screws (Ref. No. E19) holding bearing housing to pump adapter.

Grasp sled (Ref. No. S2) cross member and slide engine/sled assembly back from pump adapter. Slide far enough to access impeller approximately 10" to 12".

NOTE: If engine/sled assembly will not slide back easily, the seal plate

(Ref. No. E11) may be stuck in pump adapter. Remove two 1/2"-13 x

1" bolts (Ref. No. E12) from bearing housing. Insert two 1/2"-13 x 1-

3/4" bolts and tighten evenly and slowly until seal plate loosens from pump adapter.

4. Tighten 1/2-13 nuts to prevent engine/sled from moving during maintenance procedure.

To access pump volute and inside of casing:

3 5585-250-00

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

5.

6.

7.

Loosen four 5/8-11 x 6-1/2" hex bolts (Ref. No. C12) holding casing to adapter. Slide 5/8" bolt -washer-nut from casing and adapter ear four total bolts.

Grasp sled cross member and slide engine/sled assembly back from pump casing. Slide far enough to access volute

(Ref. No. C24 approximately 10" to 12".

Tighten 1/2-13 nuts to prevent engine/sled from moving during maintenance procedure.

Make certain that unit is disconnected from power source before attempting to service or remove any components!

MECHANICAL SEAL REPLACEMENT

NOTE: Always replace the mechanical seal parts (Ref. No. E6 & E7) as an assembly (Ref. No. E5) to ensure proper mating of mechanical components.

NOTE: Always inspect impeller stub shaft ball bearing (Ref. No. E14) during seal replacement. The bearing may have been damaged by leaking water. Refer to IMPELLER STUB SHAFT BEARING

REPLACEMENT section.

1.

2.

Access impeller/seal plate area as described in SLIDING

ENGINE SLED OPERATION section.

Unscrew impeller (Ref. No. E2) from the impeller stub shaft

(Ref. No. E15). Use a rubber mallet or soft block of wood

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13. and hammer to loosen impeller. Remove any impeller shims

(Ref. No. E3), shaft sleeve and seal head (Ref. E6) from impeller stub shaft.

Remove two 1/2-13x1" cap screws (Ref. No. E12) holding seal plate (Ref. No. E11) to bearing housing (Ref. No. E17 or E18). Remove seal plate from bearing housing.

Remove impeller shaft washer (Ref. No. E13) and inspect impeller stub shaft ball bearing for water damage or wear.

Replace shaft washer with flat surface toward impeller.

Push seal seat from the seat plate recess with a screwdriver.

Clean the seal plate recess before inserting a new seal seat.

Carefully wipe the polished surface of the seal seat with a clean cloth.

Wet the rubber portion of the seal seat with a light coating of soapy water.

Press the new seal seat squarely into the cavity in the seal plate. If the seal seat does not press squarely into the cavity, it can be adjusted in place by pushing on it with a piece of pipe. Always use a piece of cardboard between the pipe and the seal seat to avoid scratching the seal seat.

(This is a lapped surface and must be handled very carefully).

After the seal seat is in place, ensure that it is clean and has not been scratched or cracked.

Using a clean cloth, wipe the impeller stub shaft and make certain that it is clean.

Install seal plate and secure to bearing housing adapter face with two 1/2-13x1 cap screws.

Apply a light coating of soapy water to the inside rubber portion of seal head and slide onto the shaft sleeve. Slip the shaft sleeve and seal head onto the impeller stub shaft with

14.

15. seal head lapped surface towards seal seat lapped surface.

Replace any impeller shims removed during disassembly.

Screw the impeller back in place tightening until it is seated against shims and shaft sleeve.

NOTE: Make sure seal spring retainer is not pinched between impeller/shims and end of shaft sleeve.

16.

17.

Refer to section entitled Shim Adjustment at this time if shaft sleeve or any other parts listed therein have been replaced.

Check seal plate O-ring (Ref. No. C37), make sure it is not damaged or worn and is in position on seal plate.

8/2012

Specifications Information and Repair Parts Manual x

6” Trash Pump

NOTE: Always inspect O-ring seals. Replace when cracked or worn.

Wet the O-ring with soapy water for ease of assembly.

18.

19.

Slide engine/sled back into position aligning lead diameter on seal plate with adapter inside diameter. Replace three 1/2-

13x1-3/4 cap screws. Tighten six 1/2- 13 hex nuts clamping sled to casing frame.

Remount any other parts and reconnect spark plug wires and battery.

SHIM ADJUSTMENT

Manual Method:

1. When installing a replacement impeller, shaft sleeve, bearing housing, seal plate, or volute (Ref. No. C24), it may be necessary to vary the number of impeller shims that will be required. This is done by adding one shim more than was

2.

3. removed and reassembling the pump as described in

Mechanical Seal Replacement section.

Ensure that volute, adapter, seal plate and bearing housing are fitted firmly. Check tightness of all fasteners.

Remove spark plug wires and bump engine over slightly with electric starter. If engine does not turn freely or interference between impeller and volute can be heard, disassemble pump and remove one shim.

NOTE: When adding or removing shims, it is best to proceed with a

0.020" increment each time. If engine does turn freely, add shims until it does strike, then remove a 0.020" shim. This will ensure maximum performance.

4.

5.

Proper running clearance is 0.020" to 0.040"

Follow the above procedure until proper clearance is obtained.

Measurement Method:

1.

2.

3.

4.

5.

When installing a replacement impeller, shaft sleeve, bearing adapter, seal plate or volute, it may be necessary to vary the number of impeller shims that will be required. This can be accomplished by measurement with a suitable size depth micrometer or similar measuring instrument.

Measure depth from pump adapter-seal plate mounting surface to impeller face of volute. Measurement should be close to 5.960".

Add or remove impeller shims until height of impeller face to seal plate pump adapter mounting surface measures 0.020" to 0.040" shorter than depth measured in previous step.

Slide engine/sled back into position aligning lead diameter on seal plate with adapter inside diameter. Replace three 1/2-

13x1-3/4 cap screws. Tighten six 1/2-13 hex nuts clamping side rails to frame rails.

Remove spark plug wires and bump engine over slightly with electric starter. If engine does not turn freely or interference between impeller and volute can be heard, disassemble pump and remove one shim. Rotate engine again. Engine must rotate freely.

IMPELLER AND VOLUTE REPLACEMENT

Impeller and volute are subject to wear only by abrasive sand or sediment laden liquids. If badly worn, all these parts can be replaced and the pump thus restored to full efficiency.

NOTE: When the clearance between the impeller and the volute exceeds 1/16" at the face of the impeller or 1/8" on the outside diameter of the impeller, it may be necessary to take corrective action.

The increased clearance can cause lengthened priming times and reduce pumping capacity. If both the priming and capacity of your unit are satisfactory for your application, it is recommended that no corrective maintenance be performed regardless of what clearances on your unit may have developed, since the increased clearances in themselves are not generally harmful to your pump. Normally, new pump clearances can be restored by simply shimming behind the

4 5585-250-00

5585-B6, 5585-D6, 5585-H6, & 5587-Y6 impeller. If the impeller is badly worn, it is recommended that the impeller be replaced. This is usually all that is required since only on unusually abrasive services does the cast iron volute show deterioration. Occasionally a stone or hard object might get caught in the impeller and cause damage to the volute/cutwater. In these cases, follow the instructions below for replacement.

1.

2.

Refer to "Sliding Engine Sled Operation" section for procedure to access the volute and inside of the casing.

Remove casing O-ring (Ref. No. C35) from outside diameter of volute (Ref. No. C24) flange.

A mechanical means of supporting the volute during this procedure is recommended. The volute casting weighs 50 lbs.

3. Remove three 1/2-13 x 1-1/4" cap screws holding volute to pump adapter (Ref. No. 28). Slide volute out of adapter

4. machined pocket.

Replace worn parts as necessary.

NOTE: When replacing volute, attach a new volute gasket (Ref. No.

C36) to new volute with fasteners.

NOTE: Before installing new parts, clean all mating surfaces thoroughly.

5. Install volute aligning flange outside diameter with adapter machined pocket. Replace three 1/2-13 cap screws. Check for interference between impeller face and volute by slowly rotating engine shaft. See SHIM ADJUSTMENT section for

6.

7. procedure to set impeller clearance.

Inspect casing O-ring for cracks or tears, replace if necessary. Install O-ring on outside diameter of volute flange.

Slide engine sled and engine assembly into casing, align outside diameter of volute flange with casing machined inside diameter, do not pinch casing O-ring. Install four 5/8-

11 hex bolts and nuts. Tighten six 1/2-13 hex nuts clamping engine sled in position.

IMPELLER STUB SHAFT BEARING REPLACEMENT

Gas engine units are equipped with a permanently lubricated impeller shaft ball bearing (Ref. No. E14). Diesel engine units are equipped with two bearings. These bearings support the radial and axial loads produced by the impeller reducing the load on the engine crankshaft bearings. The bearing does not require lubrication but should be inspected periodically for wear or water damage from a leaking shaft seal. As part of a maintenance schedule, the bearing should be replaced periodically.

1. Refer to "Sliding Engine Sled Operation" section. Access impeller as described.

2.

3.

4.

5.

6.

7.

Refer to MECHANICAL SEAL REPLACEMENT section.

Follow steps 1 through 3; remove impeller, impeller shims, shaft sleeve, seal and seal plate.

Remove shaft washer.

Remove cap screws (Ref. No. E20 or E21) fastening bearing housing to engine (Ref. No. E38). Diesel engine units:

Loosen set screw in impeller stub shaft. Remove bearing housing assembly from engine by sliding away from engine.

Gas engine and Vanguard diesel units: disengaging engine

PTO shaft from impeller stub shaft. Do not lose shaft key

(Ref. No. E16). Yanmar diesel engine units: disengaging flywheel drive hub attached to impeller stub shaft from flywheel drive plate and flywheel bearing.

On appropriate bearing press, press stub shaft and bearing from bearing housing adapter. Remove bearing from stub shaft.

Replace bearing with equivalent ball bearing. Reassemble bearing, stub shaft and bearing adapter.

Gas engine and Vanguard diesel engine units: insert shaft key into engine PTO shaft. Align shaft key with stub shaft key way, slide stub shaft, bearing adapter assembly onto engine

8/2012

Specifications Information and Repair Parts Manual x

6” Trash Pump and secure with fasteners. Yanmar diesel units: align flywheel drive hub with flywheel drive plate and align end if impeller stub shaft with bearing in flywheel. Slide assembly in until bearing housing seats on engine bell housing. Secure with fasteners.

NOTE: Apply a light coating of anti-seize compound to shaft to prevent corrosion and galling.

8.

9.

Replace shaft washer onto stub shaft. Flat surface of shaft washer must face impeller.

Replace seal plate, shaft sleeve, seal, impeller shims and impeller, turn clockwise to tighten. Refer to MECHANICAL

SEAL REPLACEMENT section; follow step 12 and steps 14 through 19 for reassembly procedure.

CLEANING

These units are designed so that for most cleanout or clogging problems it should not be necessary to remove hoses or piping. The suction area can be reached by removing two threaded handles (Ref.

No. C10) and removing suction cleanout cover plate (Ref. No. C11) and O-ring (Ref. No. C34). To reach the impeller chamber or casing discharge areas, follow procedures described in SLIDING ENGINE

SLED OPERATION.

NOTE: When replacing cleanout cover plate, carefully wipe clean all surfaces on which the O-ring has contact. Also make sure the O-ring is in position in its groove.

ENGINE (DRIVER)

1.

2.

3.

4.

5.

For information pertaining to the engine, engine service and engine parts, consult the Engine Manual or contact the nearest authorized service representative or the engine manufacturer.

Follow engine manufacturer’s operating and maintenance procedures and recommendations covered in the engine manual.

Use tachometer-hour meter installed on the engine to log operating hours. See tachometer-hour meter instruction sheet included for operating information. Perform engine maintenance according to recommended hour intervals listed in engine manual.

An engine oil drain extender has been installed in the engine oil drain port to assist in changing the engine oil. Adding longer piping, hose, or a valve to fit each individual’s maintenance requirements is left to the discretion of the operator.

Consult engine manual for engine warranty information needed. Any warranty issues concerning the engine must be address through the engine manufacturer. Warranty contact phone number, website, Authorized Service Representative listing and warranty directions are listed in the engine manual.

5 5585-250-00

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

Yanmar 3TNM72

1. Use the engine fuel system hand primer to prime the engine with fuel on initial start-up or whenever the fuel system has

2. been drained. See engine manual for details. Do not use the engine starter to crank the engine until the fuel system is primed.

Maximum ambient air temperature during engine operation is

3.

45°C (113°F). Engine may not cool itself effectively if operated when ambient air temperature exceeds this limit. If pump is used below 0°C (32°F) do not allow water to freeze inside the pump. Damage to the pump components will occur if water freezes inside pump.

Engine speed may be set at 3600 rpm during the priming cycle. Once pump is fully primed engine speed must be reduced to a maximum speed of 3200 rpm. Damage to engine or pump end may result if operated for an extended period of time at speeds greater than 3200 rpm.

TRAILER GEAR

Routine Maintenance:

Routine maintenance is required on trailer equipment. Follow guidelines listed.

1.

2.

3.

Lubricate ball coupling mechanism as required to ensure smooth positive action.

Apply light coating of lubricating grease to tow ball coupler.

Inspect safety chains for wear; replace if required. Check

4.

5.

6.

7.

8. safety chain mounting bolt, torque to 20-25 ft. lbs. if required.

Torque lug nuts to 85-90 ft. lbs. after initial use then after every 250 miles.

Torque tongue to frame mounting bolts (4 total) to 15-18 ft. lbs. every 250 miles or monthly.

Torque axle spring hanger to frame mounting bolts (4 total) to 45-50 ft. lbs. every 500 miles or yearly.

Torque axle U-bolts to 30-35 ft. lbs. every 500 miles or yearly.

Repack wheel bearing with NLGI Grade-2 wheel bearing grease (Pennzoil 302 EP or equivalent) every 1000 miles or yearly.

8/2012

Specifications Information and Repair Parts Manual x

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

For Repair Parts contact dealer where pump was purchased.

Please provide following information:

-Model Number

-Serial Number (if any)

Part description and number as shown in parts list

Gas Engine Pump – Honda & Briggs & Stratton

Diesel Engine Pump –Daihatsu/Vanguard

5585-250-00 6 8/2012

Specifications Information and Repair Parts Manual x

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

For Repair Parts contact dealer where pump was purchased.

Please provide following information:

-Model Number

-Serial Number (if any)

Part description and number as shown in parts list

Diesel Engine Pump –Yanmar

5585-250-00 7 8/2012

Specifications Information and Repair Parts Manual x

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

Ref.

No. Description

E1

E2

E3

E4

E5

E6

E7

E8

Impeller Kit (includes Ref. Nos. E2, E3, E4)

Impeller

Impeller Shim Package

Shaft Sleeve

Mechanical Shaft Seal Kit (includes Ref. Nos. E6, E7)

Shaft Seal Head

Shaft Seal Seat

Seal Plate/Bearing Housing Kit

5585-B6

5586-B6

5585-010-98

Incl. w/E1

Incl. w/E1

5585-140-01

5585-301-90

Incl. w/E5

(includes Ref. Nos. E11 thru E17 or E18, E19, E20 or E21)

Seal Plate Kit (includes Ref. No. E11)

Incl. w/E5

5585-090-95

E9

E10 Stub Shaft Kit (includes Ref. Nos. E13, E14, E15, E16)

5585-031-95

5585-140-90

E10 Stub Shaft Kit

(includes Ref. Nos. E13, E14, E15, E16, E39)

N/A

E11 Seal Plate

E12 1/2-13x1 Hex Screw

E13 Stub Shaft Washer

E14 Ball Bearing Sealed #6209 (45idx85odx19w)

E15 Stub Shaft

E16 1/4 Square x 1-1/2" Long Drive Key

E17 Bearing Housing/Engine Adapter

E18 Bearing Housing/Bell Housing Adapter

E19 1/2-13x1-3/4 Hex Screw

E20 7/16-14x1-1/4 Hex Screw

E21 M10x1.5x30mm Hex Screw

E22 Gasoline engine Mounting Hardware

E23 Engine Oil Drain Extender

E24 Tachometer/Hour Meter

E25 Mounting Bolts

E26 Mounting Nuts

E27 Engine Shim Set

E28 Diesel Engine Hardware Kit

E29 Tachometer/Hour Meter

E30 Tachometer Wire Harness

E31 Throttle Control (includes Head and Cable)

E32

E33

E34

E35

Diesel Engine Mounting Hardware Kit

3/8-16x1 Hex Bolt

3/8-16 Hex Flange Nut

Mounting Shim Set

E36 Fan Guard Assembly

E37 Battery Cable Kit (includes "+" & "-" cables for gas engines) 5585-350-90

Diesel Engine "+" Battery Cable

Diesel Engine "-" Battery Cable

E38 Engine

E39 1/4-20 x 3/8 Set Screw

E40 SAE 6-1/2 Drive Plate Kit (includes Ref. Nos. E41, E42)

E41 SAE 6-1/2 Drive Plate

E42 M8x1.25x20 Cap Screw

E43 Engine Bracket Kit (includes Ref. Nos. E44 thru E51)

Incl. w/E9

Incl. w/E8

Incl. w/E8

N/A

5580-140-00

Incl. w/E10

Incl. w/E8

N/A

Incl. w/E8

Incl. w/E8

N/A

Incl. w/E22

Incl. w/E22

Incl. w/E22

Incl. w/E22

Incl. w/E22

Incl. w/E22

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

5585-031-95

5585-140-90

N/A

Incl. w/E9

Incl. w/E8

Incl. w/E8

N/A

5580-140-00

Incl. w/E10

Incl. w/E8

N/A

Incl. w/E8

Incl. w/E8

N/A

Incl. w/E22

Incl. w/E22

Incl. w/E22

Incl. w/E22

Incl. w/E22

Incl. w/E22

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

5585-350-90

N/A

N/A

1639-010-00

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Part Number for Models:

5585-H6

5586-H6

5585-010-98

Incl. w/E1

Incl. w/E1

5585-140-01

5585-301-90

Incl. w/E5

Incl. w/E5

5585-090-95

5585-D6

5586-D6

5585-010-98

Incl. w/E1

Incl. w/E1

5585-140-01

5585-301-90

Incl. w/E5

Incl. w/E5

5585-091-96

E48 Engine Block Foot

E49 Engine Bell Housing Foot

E50 M10x1.5x20 Hex Screw

E51 1/2-13x1-1/4 Hex Bolt

N/A

N/A

1639-011-00

N/A

N/A

N/A

N/A

N/A

E44 Control Box Bracket Adapter

E45 M10x1.5x20 Cap Screw

N/A

N/A

E46 1/4-20x1/2 Hex Screw N/A

E47 Engine Mounting Feet Kit

(includes Ref. Nos. E53 thru E58)

N/A

E52 Shim

E53 1/2-13 Hex Nut

N/S Muffler (Honda)

N/S Throttle Control

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

1639-013-00

N/A

N/S Control Box/Tachometer/Hour Meter N/A

NOTE: Dual ball bearing stub shaft kit for 5585-D6 and 5586-D6 added for pumps serial number A35585D6G (0610 date code)

N/A and later. All pumps with earlier date code use single bearing stub shaft kit 5585-140-90.

5585-031-95

N/A

5585-140-91

Incl. w/E9

Incl. w/E8

Incl. w/E8

1695-080-00

5580-140-01

Incl. w/E10

N/A

Incl. w/E8

Incl. w/E8

N/A

Incl. w/E8

N/A

N/A

N/A

N/A

N/A

N/A

5585-420-93

Incl. w/E28

Incl. w/E28

Incl. w/E28

5585-420-92

Incl. w/E32

Incl. w/E32

Incl. w/E32

5585-420-94

5585-350-90

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

1639-050-00

Incl. w/E10

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

5587-Y6

5585-010-98

Incl. w/E1

Incl. w/E1

5585-140-01

5585-301-90

Incl. w/E5

Incl. w/E5

5587-090-96

5585-031-95

5587-140-90

N/A

Incl. w/E9

Incl. w/E8

Incl. w/E8

1695-080-00

5585-141-00

Incl. w/E10

N/A

Incl. w/E8

Incl. w/E8

N/A

Incl. w/E8

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

5587-350-90

5587-351-90

1639-057-00

N/A

5587-400-90

Incl. w/E40

Incl. w/E40

5587-421-90

Incl. w/E43

Incl. w/E43

Incl. w/E43

5587-420-90

Incl. w/E52

Incl. w/E52

Incl. w/E52

Incl. w/E52

Incl. w/E52

Incl. w/E52

N/A

5583-403-00

Call for Availability

1

1

1

1

1

8

8

1

1

1

1

1

1

4

4

1

4

8

1

1

1

1

1

3

2

1

2

1

1

1

1

1

8

4

8

4

4

1

2

2

1

1

1

6

1

1

2

1

1

1

1

Qty.

1

1

1

1

1

1

1

1

8 8/2012 5585-250-00

Specifications Information and Repair Parts Manual x

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

For Repair Parts contact dealer where pump was purchased.

Please provide following information:

-Model Number

-Serial Number (if any)

Part description and number as shown in parts list

5585-250-00

Frame Explosion

9 8/2012

Specifications Information and Repair Parts Manual x

Repair Parts List - Frame Explosion

Ref.

No. Description

F1 Frame Kit

F2 Lifting Bail Kit

(includes Ref. Nos. F3 thru F9)

F3 Lifting Bail

F4 5/8-11x3-1/2 Heavy Hex Bolt

F5 Bolt Spacer

F6 5/8-11 Heavy Hex Nut

F7 Lifting Support

F8 1/2-13x1-1/4 Hex Flange Bolt

F9 1/2-13 Hex Flange Nut

F10 Vibration Dampener Kit

(includes Ref. Nos. F11 thru F16)

F11 1/2-13x2-1/4 Hex Bolt

F12 5/8 Washer

F13 Rubber Washer

F14 Sleeve

F15 1/2 Washer

F16 1/2-13 Hex Flange Nut

5585-B6

5586-B6

5585-100-90

5585-103-90

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

5585-111-90

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

Part Number for Models:

5585-H6

5586-H6

5585-D6

5586-D6

5585-100-90

5585-103-90

5585-100-90

5585-103-90

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

5585-111-90

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

5585-111-90

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

NOTE: Following parts are for trailer mounted units, not included on skid mounted units (5586-B6, 5586-H6, & 5586-D6).

F17 Fender Kit

(includes Ref. Nos. F18 thru F21)

F18 Fender

F19 5/16-18x1-1/4 Hex Flange Bolt

F20 5/16-18 Hex Flange Nut

F21 Coupler/Safety Chain Kit

(includes Ref. Nos. F22 thru F27)

F22 2" Ball Coupler

5585-440-90

Incl. w/F17

Incl. w/F17

Incl. w/F17

5585-441-90

Incl. w/F21

F23 1/2-13x3-1/2 Hex Bolt

F24 1/2-13 Hex Flange Nut

F25 Safety Chain (not shown)

F26 3/8-16x4 Hex Bolt (not shown)

F27 3/8-16 Hex Nut (not shown)

F28 Tongue Kit

(includes Ref. Nos. F29 thru F31)

F29 Tongue

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

5585-107-90

F30 5/16-18x1-1/4 Hex Flange Bolt

F31 5/16-18 Hex Flange Nut

F32 Jack

F33 Tire/Wheel Kit

F34 Axle/Spring Kit

(includes Ref. Nos. F35 thru F39)

F35 Axle

F36 Springs and Hangers

Incl. w/F28

Incl. w/F28

Incl. w/F28

5585-443-00

5585-444-00

5585-445-90

F37 U Bolts/Plates/Nuts

F38 1/2-13x1-1/4 Hex Flange Bolt

Incl. w/F34

Incl. w/F34

F39 1/2-13 Hex Flange Screw Incl. w/F34

F40 Light Kit 5585-351-90

(includes: tail lights, side lights, protective conduit, & connection plug)

F41 Support Leg Kit

(includes Ref. Nos. F42, F43)

F42 5/8x3" Long Pin with Cotter Key

F43 Support Leg

Incl. w/F34

Incl. w/F34

5585-108-90

Incl. w/F41

Incl. w/F41

5585-440-90

Incl. w/F17

Incl. w/F17

Incl. w/F17

5585-441-90

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

5585-107-90

Incl. w/F28

Incl. w/F28

Incl. w/F28

5585-443-00

5585-444-00

5585-445-90

Incl. w/F34

Incl. w/F34

Incl. w/F34

Incl. w/F34

Incl. w/F34

5585-351-90

5585-108-90

Incl. w/F41

Incl. w/F41

5585-440-90

Incl. w/F17

Incl. w/F17

Incl. w/F17

5585-441-90

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

5585-107-90

Incl. w/F28

Incl. w/F28

Incl. w/F28

5585-443-00

5585-444-00

5585-445-90

Incl. w/F34

Incl. w/F34

Incl. w/F34

Incl. w/F34

Incl. w/F34

5585-351-90

5585-108-90

Incl. w/F41

Incl. w/F41

5585-440-90

Incl. w/F17

Incl. w/F17

Incl. w/F17

5585-441-90

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

Incl. w/F21

5585-107-90

Incl. w/F28

Incl. w/F28

Incl. w/F28

5585-443-00

5585-444-00

5585-445-90

Incl. w/F34

Incl. w/F34

Incl. w/F34

Incl. w/F34

Incl. w/F34

5585-351-90

5585-108-90

Incl. w/F41

Incl. w/F41

5587-Y6

5585-100-90

5585-103-90

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

Incl. w/F2

5585-111-90

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

Incl. w/F10

1

1

1

1

2

8

8

5

Qty.

1

1

1

1

3

1

1

1

1

1

3

3

2

1

2

1

2

4

4

1

1

1

1

4

4

1

2

1

4

4

1

2

1

2

2

5585-250-00 10 8/2012

Specifications Information and Repair Parts Manual x

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

For Repair Parts contact dealer where pump was purchased.

Please provide following information:

-Model Number

-Serial Number (if any)

Part description and number as shown in parts list

5585-250-00

Sled Explosion

11 8/2012

Specifications Information and Repair Parts Manual x

Repair Parts List - Sled Explosion

Ref.

No. Description

S1 Engine Sled Kit

(includes Ref. Nos. S2 thru S8)

S2 Sled

S3 Engine Mounting Bracket

S4 Battery Mounting Bracket

S5 Slip Strip

S6 #10-24X1/2 Flat Head Screw

S7 3/8-16x1 Hex Flange Bolt

5585-B6

5586-B6

5585-102-90

Incl. w/S1

Incl. w/S1

Incl. w/S1

Incl. w/S1

Incl. w/S1

Incl. w/S1

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

Part Number for Models:

5585-H6

5586-H6

5585-102-90

5585-D6

5586-D6

5585-102-91

Incl. w/S1

Incl. w/S1

Incl. w/S1

Incl. w/S1

Incl. w/S1

Incl. w/S1

Incl. w/S1

N/A

Incl. w/S1

Incl. w/S1

Incl. w/S1

N/A

5587-Y6

5585-102-91

Incl. w/S1

N/A

Incl. w/S1

Incl. w/S1

Incl. w/S1

N/A

S7 3/8-16x1 Hex Flange Bolt

S8 3/8-16 Hex Flange Nut

S8 3/8-16 Hex Flange Nut

S9 Battery Box Kit

(includes Ref. Nos. S10 thru S12)

N/A

Incl. w/S1

N/A

5585-350-91

N/A

Incl. w/S1

N/A

5585-350-91

Incl. w/S1

N/A

Incl. w/S1

5585-350-91

Incl. w/S1

N/A

Incl. w/S1

5585-350-91

S10 Battery Box

S11 5/16-18x3/4 Hex Flange Bolt

S12 5/16-18 Hex Flange Nut

S13 Fuel Tank

Incl. w/S9

Incl. w/S9

Incl. w/S9

Incl. w/S9

Incl. w/S9

Incl. w/S9

Incl. w/S9

Incl. w/S9

Incl. w/S9

S14 Fuel Tank Mounting Kit

(includes Ref. Nos. S15, S16)

5580-170-00

5585-171-91

5580-170-00

5585-171-91

5580-171-00

5585-171-91

S15 5/16-18x3/4 Hex Flange Bolt

S16 5/16-18 Hex Flange Nut

S17 Fuel Hose and Fitting Kit (Gasoline)

Incl. w/S14

Incl. w/S14

5585-171-93

Incl. w/S14

Incl. w/S14

5585-171-93

Incl. w/S14

Incl. w/S14

N/A

(includes (1) 1/4id fuel hose, (2) hose clamps, (all not shown), Ref. Nos. S19, S20, S22, S23, S24, S25, and S26)

Incl. w/S9

Incl. w/S9

Incl. w/S9

5580-171-00

5585-171-91

Incl. w/S14

Incl. w/S14

N/A

S18 Fuel Hose and Fitting Kit (Diesel) N/A N/A 5585-171-92 5587-170-90

(includes (2) 5/16id fuel hose, (1) 1/4id fuel hose, (6) hose clamps, (all not shown), Ref. Nos. S19, S20, S22, S23, S24, S25, and S26)

Qty.

1

1

1

4

4

1

1

4

4

1

1

1

1

2

8

8

4

8

4

1

S19 Fuel Level Gauge

S20 Fuel Tank Vent 3/8" NPT

S21 Fuel Vent Check Valve 3/8" NPT

S22 1/4" NPT Plug

S23 1/4" NPT Street Elbow

S24 1/4" NPT Valve

S25 1/4" NPT x 1/4" Hose Barbed Fitting

S25 1/4" NPT x 5/16" Hose Barbed Fitting

S26 1/4" NPT Plug

S26 1/4" NPT x 1/4" Hose Barbed Elbow

S27 Fuel Tank Cap

Incl. w/S17

Incl. w/S17

N/A

Incl. w/S17

Incl. w/S17

Incl. w/S17

Incl. w/S17

N/A

Incl. w/S17

N/A

5585-172-00

Incl. w/S17

Incl. w/S17

N/A

Incl. w/S17

Incl. w/S17

Incl. w/S17

Incl. w/S17

N/A

Incl. w/S17

N/A

5585-172-00

Incl. w/S18

Incl. w/S18

N/A

Incl. w/S18

Incl. w/S18

Incl. w/S18

N/A

Incl. w/S18

N/A

Incl. w/S18

5585-172-00

Incl. w/S18

Incl. w/S18

N/A

Incl. w/S18

Incl. w/S18

Incl. w/S18

N/A

Incl. w/S18

N/A

Incl. w/S18

5585-172-00

1

1

1

1

1

1

1

1

1

1

1

12 8/2012 5585-250-00

Specifications Information and Repair Parts Manual x

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

For Repair Parts contact dealer where pump was purchased.

Please provide following information:

-Model Number

-Serial Number (if any)

Part description and number as shown in parts list

5585-250-00

Casing Mounting Explosion

13 8/2012

Specifications Information and Repair Parts Manual x

Repair Parts List - Casing Mounting Explosion

Ref.

No. Description

C1 Casing Kit

5585-B6

5586-B6

5585-001-96

5585-B6, 5585-D6, 5585-H6, & 5587-Y6

Part Number for Models:

5585-H6

5586-H6

5585-001-96

5585-D6

5586-D6

5585-001-96

5587-Y6

5585-001-96

Qty.

1

(includes Ref. Nos. C5, C12, C13, C14, and C15)

C2 Suction Flange Kit

(includes Ref. Nos. C6, and C9)

5585-082-95 5585-082-95 5585-082-95 5585-082-95 1

5585-081-95 5585-081-95 5585-081-95 5585-081-95 1 C3 Discharge Manifold Kit

(includes Ref. Nos. C7, C8, and C9)

C4 Clean-out Cover Kit

(includes Ref. Nos. C10, and C11)

5585-040-95 5585-040-95 5585-040-95 5585-040-95 1

C5 Casing

C6 Suction Flange

C7 Discharge Manifold

C8 1-1/2" NPT Plug

Incl. w/C1

Incl. w/C2

Incl. w/C3

Incl. w/C3

Incl. w/C1

Incl. w/C2

Incl. w/C3

Incl. w/C3

Incl. w/C1

Incl. w/C2

Incl. w/C3

Incl. w/C3

Incl. w/C1

Incl. w/C2

Incl. w/C3

Incl. w/C3

1

1

1

1

C9 5/8-11x1-3/4 Hex Screw

C10 3/8-16x1-1/4 Handle

C11 Clean-out Cover

C12 5/8-11x6-1/2 Hex Bolt

C13 5/8-11 Heavy Hex Nut

C14 1/2-13x1-1/4 Hex Screw

C15 1/2-13x1 Cap Screw

C16 Flapper/Check Valve Kit (includes Ref. Nos. C17 thru C22)

C17 1/4-20x3/4 Hex Bolt

C18 Valve Weight Front

C19 Valve

C20 Valve Weight Rear

C21 1/4-20x1/2 Hex Screw

C22 1/4-20 Hex Nut

C23 Volute Kit (includes Ref. Nos. C24 thru C26)

C24 Volute

C25 1/4-20x1/2 Hex Screw

C26 1/2-13x1-1/4 Hex Screw

C27 Adapter Kit (includes Ref. Nos. C28 thru C31)

C28 Adapter

C29 1/8" NPT Plug

C30 3/4" NPT Street Elbow

C31 3/4" NPT Plug

C32 Seal Kit (includes Ref. Nos. C33 thru C37)

C33 O-ring #369 (3/16x8"id)

C34 O-ring #355 (3/16x5-1/4"id)

C35 O-ring #386 (3/16x17"id)

C36 Volute Gasket

C37 O-ring #262 (1/8x7"id)

C38 Casing Mounting Kit (includes Ref. Nos. C39 thru C41)

C39 Casing Mounting Plate

C40 1/2-13X1-1/4" Hex Bolt

C41 1/2-13 Hex Nut

C42 Angle Frame Kit (includes Ref. Nos. C43 thru C47)

C43 Angle Frame

C44 Clamp Angle

C45 1/2-13X1-1/4" Hex Bolt

C46 1/2-13 Hex Jam Nut

C47 1/2-13 Hex Flange Nut

Incl. w/C23

Incl. w/C23

5585-030-96

Incl. w/C27

Incl. w/C27

Incl. w/C27

Incl. w/C27

5585-300-90

Incl. w/C32

Incl. w/C32

Incl. w/C32

Incl. w/C32

Incl. w/C32

5585-110-90

Incl. w/C38

Incl. w/C38

Incl. w/C38

5585-101-90

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl w/C2 & C3 Incl w/C2 & C3

1601-000-00 1601-000-00

Incl. w/C4

Incl. w/C1

Incl. w/C4

Incl. w/C1

Incl. w/C1

Incl. w/C1

Incl. w/C1

5585-070-90

Incl. w/C1

Incl. w/C1

Incl. w/C1

5585-070-90

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

5585-150-95

Incl. w/C23

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

5585-150-95

Incl. w/C23

Incl. w/C23

Incl. w/C23

5585-030-96

Incl. w/C27

Incl. w/C27

Incl. w/C27

Incl. w/C27

5585-300-90

Incl. w/C32

Incl. w/C32

Incl. w/C32

Incl. w/C32

Incl. w/C32

5585-110-90

Incl. w/C38

Incl. w/C38

Incl. w/C38

5585-101-90

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl. w/C23

Incl. w/C23

5585-030-96

Incl. w/C27

Incl. w/C27

Incl. w/C27

Incl. w/C27

5585-300-90

Incl. w/C32

Incl. w/C32

Incl. w/C32

Incl. w/C32

Incl. w/C32

5585-110-90

Incl. w/C38

Incl. w/C38

Incl. w/C38

5585-101-90

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl w/C2 & C3

1601-000-00

Incl. w/C4

Incl. w/C1

Incl. w/C1

Incl. w/C1

Incl. w/C1

5585-070-90

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

5585-150-95

Incl. w/C23

Incl. w/C23

Incl. w/C23

5585-030-96

Incl. w/C27

Incl. w/C27

Incl. w/C27

Incl. w/C27

5585-300-90

Incl. w/C32

Incl. w/C32

Incl. w/C32

Incl. w/C32

Incl. w/C32

5585-110-90

Incl. w/C38

Incl. w/C38

Incl. w/C38

5585-101-90

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl. w/C42

Incl w/C2 & C3

1601-000-00

Incl. w/C4

Incl. w/C1

Incl. w/C1

Incl. w/C1

Incl. w/C1

5585-070-90

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

Incl. w/C16

5585-150-95

Incl. w/C23

2

1

1

1

3

3

1

1

2

1

1

1

2

1

1

2

1

1

1

2

6

6

6

2

1

1

1

1

1

1

1

4

2

2

1

4

2

1

4

14 8/2012 5585-250-00

www.amtpump.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Languages