Mackie DL32R Install Rackmount Kit User Manual


Add to my manuals
2 Pages

advertisement

Mackie DL32R Install Rackmount Kit User Manual | Manualzz

Install Rack Kit Installation Instructions

Introduction

This Install Rack Kit allows a DL32R mixer to be mounted in a standard 19" rack in a variety of ways. The alternate recessed front rack ears allow connections to be made in a rack with a closing front door. The rear rack ears can be used with either front ear configuration, and, when added, provide extra stability for installs and touring systems.

These allow the DL32R to be mounted in racks with rear rack rails between 19.5" – 24.75" [using the recessed front rack ears] or 16" – 21.125" [using the standard front rack ears] from the front rails measuring from mounting surface to mounting surface.

If only the rear rack ears will be attached, please continue on with the Rear Rack Ears – Procedure instructions on the next page. If the recessed front rack ears will be attached, as well, please start with the Front Rack Ears – Procedure below.

Front Rack Ears – Procedure

1. Using the Phillips screwdriver, remove the eight screws – four screws on each side – on the front side of the mixer, as shown below. Hang on to these eight screws as they will be necessary when attaching the new, recessed rack ears (which is the next step!).

Place the removed rack ears in a safe place should you ever decide to use them again.

Parts

DL32R Rack Ear Kit Contents – Part No. 2042160:

Recessed Front Rack Ear (2) – Part No. 2042158

Rear Adjustable Rack Ear (2) – Part No. 2042154

Rear Rack Ear Bracket Adapter (2) – Part No. 2042153

2 mm Hex Key (1) – Part No. 2046096

M3 Hex Screws (4) – Part No. 2035377

M4 Screws (4) – Part No. 2046407-08

M4 Lock Washers (4) – Part No. 0021407

This instruction sheet (1) – Part No. 2042161

Tools

Required Tools (not included):

Phillips screwdriver

Getting Started

Before doing anything else...

• Turn off the mixer.

• Disconnect all cords.

• Remove mixer from the rack (if applicable).

• Unscrew and remove the four feet on the bottom

of the mixer (if applicable).

2. Using the Phillips screwdriver, attach the two new, recessed rack ears – one on each side – on the front side of the mixer using the same screws that were just removed.

Handle Rack Ear Recessed Rack Ear

Rear Rack Ears – Procedure

1. Using the Phillips screwdriver, remove the four screws – two screws on each side – on the rear side of the mixer, as shown below. Place the removed screws in a safe place should you ever decide to use them again.

4. Align the two rear rack ears – one on each side – to the outside of the ear brackets.

5. Loosely attach each rear rack ear to the rear rack rails with two rack screws 1 (not supplied).

Step 4

2. Using the hex key, attach the two bracket adapters – one on each side – on the rear side of the mixer through the fixed diameter holes using the M3 hex screws.

Step 5

6. Using the Phillips screwdriver, attach each bracket adapter to the corresponding rear rack ear with the

M4 Pan Phillips screws and locking washers, as shown below. Tighten the screws enough to securely engage the lock washers. In other words, tighten the screws only until the lock washers are seated flush to the metal.

CAUTION: It might be difficult to start thread engagement.

Be patient and keep screws as perpendicular to threads as possible. Over-torqueing the screws could strip the thread in the rack ear.

Please note the placement of the brackets and how the fixed diameter holes line up with the mixer. These holes are recessed so the screws will be flush with the bracket.

3. Place the mixer in the rack at the intended location and secure the front in place with four rack screws supplied).

1 (not

1 It is advised to only use large metal flat washers (or other non-deforming material flat washers) under rack mounting screws. Our experience is that the rubber like material washers shipped with some racks are destroyed over time by vibration in a mobile rack and can cause mounting hardware to loosen and fall out over time.

7. The rear rail mounting screws that were loosely attached in step 5 above may now be completely tightened.

8. Nice job, that’s it!

16220 Wood-Red Road NE

Woodinville, WA 98072

Phone: 425-487-4333

Toll free: 800-258-6883 www.720trees.com

© 2015 LOUD Technologies Inc. All Rights Reserved.

Part No. SW1121 Rev A 06/15

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Frequently Answers and Questions

What mounting options does this kit offer?
This kit provides two mounting options: recessed front rack ears for connections in a rack with a closing front door, and rear rack ears for added stability.
How do I install the recessed front rack ears?
Remove the eight screws on the front side of the mixer, attach the new recessed rack ears using the same screws, and secure the mixer in the rack with four rack screws (not supplied).
How do I install the rear rack ears?
Remove the four screws on the rear side of the mixer, attach the bracket adapters using M3 hex screws, align and loosely attach the rear rack ears to the rear rack rails, attach each bracket adapter to the corresponding rear rack ear with M4 Pan Phillips screws and locking washers, place the mixer in the rack and secure the front in place with four rack screws (not supplied), and tighten the rear rail mounting screws.
What tools do I need for installation?
You will need a Phillips screwdriver and a 2 mm hex key.
What is the rack compatibility of this kit?
The recessed front rack ears allow mounting in racks with rear rack rails between 19.5" – 24.75" from the front rails, and the standard front rack ears allow mounting in racks with rear rack rails between 16" – 21.125" from the front rails.

advertisement