Aquatic AQ-DM-1R Instruction manual
Add to My manuals12 Pages
Aquatic AQ-DM-1R is a waterproof and dustproof digital media locker designed to provide safe and convenient access to your music and other audio content while enjoying water activities or spending time in dusty environments. It features a built-in AM/FM radio, allowing you to tune in to your favorite stations, and an auxiliary input for connecting external audio sources. The device comes with a floating RF LCD 2-way wireless remote control, enabling you to navigate through your music and adjust volume levels from a distance.
advertisement
products with a watertight reputation
WATER/DUST PROOF DIGITAL MEDIA LOCKER™
AQ-DM-4
OWNERS MANUAL
Aquatic AV
282 Kinney Dr..
San Jose, CA 95112, USA
E-mail: [email protected]
US & Canada: 1 877 579 2782
International: +1 408 559 1668
Fax: +1 408 559 0125 www.aquaticav.com
products with a watertight reputation
WATER/DUST PROOF iPOD/MP3 DIGITAL MEDIA LOCKER™
WITH FLOATING RF LCD 2-WAY WIRELESS REMOTE CONTROL
PLEASE READ THIS INSTRUCTION MANUAL BEFORE
INSTALLATION AND OPERATION
1
GETTING STARTED
CONTENTS
• AQ-DM-4 Digital Media Locker™
• 2-way RF wireless remote control
• 2.35m audio cable (3.5mm plug to 3.5mm plug)
• One (1) CR2430 battery
• AQ-DM-4 mounting template
• Six (6) Stainless Steel mounting screws
• Owners manual
INSTALLATION
1. 12-pin Watertight Harness
This harness supplies power and ground connections to the Digital Media Locker™ and four (4) speaker channel output connections from the Digital Media Locker™. The AQ-UNH-2 (supplied separately) or a custom manufacture harness will be required.
Do not cut or modify the 12-pin harness or warranty will be void
2. FM Radio Antenna Jack
Connect antenna to female antenna receptacle. For best FM performance make sure the FM
Antenna is extended to the highest achievable position.
3. Auxiliary Input
The AQ-DM-4 has a 3.5mm stereo jack socket for connecting other audio devices.
4. Auxiliary Outputs
Allows external amplifier to be connected to power additional speakers.
5. 12V DC External Trigger
Allows for an external light or relay to be triggered (350mA max load).
FM Radio
Antenna Jack
Aux’ Input
Jack Socket
12 pin
Harness Cable
Left Audio - RCA Output Jack
Right Audio - RCA Output Jack
External 12V Trigger (Brown) www.aquaticav.com
FCC STATEMENT
FCC ID:
MADE IN CHINA
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE:
The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
- Reorientate or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.
Product design and specification subject to change without notice. E&OE.
Digital Media Locker™ is a Trademark of Aquatic AV.
iPod is a Trademark of Apple Inc, registered in the US and other countries.
Doc V4 Feb12 www.aquaticav.com
10
9
SPECIFICATIONS
TECHNICAL SPECIFICATION
General
Power Supply:
Current drain when OFF:
Remote Control Frequency:
Remote Control Battery:
External Trigger:
IP Rating (Digital Media Locker™):
UV Protection:
FM Radio
FM Radio Sensitivity:
FM Antenna:
FM Radio Reception:
Number of Radio Presets:
Amplifier
Distortion:
Frequency Response:
Amplifier Output:
10.7V - 15.6V DC, 5A min
0A
2.4GHz
3V (1 x CR2430 battery)
12V DC, 350mA max
IP65
500 hours stable without degradation
8uV
Dipole Antenna (not included)
Stereo
3
<0.1% THD at 1kHz
20Hz - 20kHz
45W per channel at 4 Ohm load
72W per channel at 2 Ohm load www.aquaticav.com
F
GETTING STARTED
12-PIN HARNESS
The AQ-DM-4 will require a universal harness (AQ-UNH-2) in order to connect the dock to power and speakers.
All open wire connections should be soldered and protected against water and dust for best long term performance.
Speaker
Right
Rear
RR (Pin 11) (Purple/Black Stripe)
RR (Pin 12) (Purple)
DC Ground (Pin 10) (Black)
Right
Front
RF (Pin 8) (Gray/Black Stripe)
RF (Pin 9) (Gray)
+12VDC, Triggered (Pin 6) (Blue)
Not Used (Pin 6)
+12VDC (Pin 1) (Red)
Left
Rear
LR (Pin 3)
LR (Pin 2)
(White/Black Stripe)
(White)
Left
Front
LF (Pin 5)
LF (Pin 5)
(Green/Black Stripe)
(Green)
No lower than a 2 Ohm load should be used or damage may occur to the Digital Media Locker ™.
Make sure the polarity of speakers are connected correctly.
MOUNTING THE UNIT
1. Mounting templates are included. Aquatic AV recommends
1. using the ‘measure twice, cut once’ method.
2. Once the mounting hole is complete, make sure the outside
2. surface is clean and clear of debris. The Digital Media
2.
Locker™ has an external water/dust proof gasket, but this
2. requires a clean surface for best performance.
3. The Digital Media Locker™ has six(6) front screws. Drive
2.
the 6 screws using a screw driver. During final mounting,
3.
apply equal pressure to all points for the best water/dust
3..
outer seal performance.
4. Review all outside surfaces of the Digital Media Locker™ to
4. ensure proper water/dust seal. This is important for long
4.
term environmental protection performance for iPod or MP3
4. devices.
www.aquaticav.com
2
3
GETTING STARTED
Remove the RF Wireless Remote control from the Digital Media Locker. Unscrew the waterproof cap on the back of the remote control. Place the CR-2430 battery in the RF
Remote control and replace the water/dust proof cap.
battery in the RF remote control and replace the water/dust proof cap.
power on
To activate the Digital Media Locker™ press the on/off button. ON will be indicated by a red
LED.
For applications that require zero current draw, and where battery drain may occur, the power button must be turned OFF. When the power button is in the OFF position the red LED will not be lit.
When the power button is in the OFF position the red LED will not be lit.
For applications where a 12V battery is not used, such as in a Spa, the power button can be left ON and the remote control can then be used to power on/off accordingly.
REMOTE SYNCHRONIZING remote synchronizing
1. Turn the docking station OFF with the on/off button inside the door (the red LED should
1. Turn the docking station OFF with the on/off button inside the door (the red LED
2. Press the red (POWER) button on the remote.
2. Press the red (POWER) button on the remote.
3. Press and hold the (MODE) button until the LCD reads PAIR.
4. Continue to press the MODE button during step 5 below.
red LED will illuminate when power is ON).
5. The remote’s LCD should read WELCOME or show a mode position such as RADIO,
6. The remote’s LCD should read WELCOME or show a mode position such as
RADIO, IPOD, or AUX IN.
For any additional remote controls, you will also need to activate/synchronize those the stereo for 3 minutes. Reattach the harness and repeat steps 1-5 above.
If the LCD displays “- -” in either mode, this means that your remote control is out of reception range. Please move closer and try the feature again.
Each Digital Media Locker™ comes with a matching RF (Radio Frequency) Wireless LCD remote control. This remote is required to use any functions on the unit. For any additional remote controls you will need to activate/synchronize those remote controls to the AQ-DM-4 by following the steps above.
If you loose your remote control and buy another new remote control, please follow the above to start pairing before normal usage.
If you lose your remote control and buy a replacement, follow the steps above to pair/synchronize before normal usage.
www.aquaticav.com
OTHER FEATURES
EXTERNAL TRIGGER
Aquatic AV understands the need for more flexible remote applications. With the Digital
Media Locker™ Aquatic AV has provided an independent 12V “accessory” trigger, activated from the RF wireless remote that allows the user to activate non-iPod, MP3 related devices.
This could include and 12V based device like 12V lights or surveillance camera.
1. In any operational mode, press the (12V TRIGGER) key to activate. Press again to deactivate.
2. We strongly recommend you speak to our technical service staff or your dealer if you are considering using this feature.
Load on External Trigger should not exceed 350mA iPOD CHARGING
When specified iPod devices are connected to the Digital Media Locker™ 30-pin connector the iPod battery will charge.
To avoid rusting as a result of electrical potential in the connector, the battery of your iPod devices must not be totally drained. If your iPod is not charged at all then the
Digital Media Locker will not charge it.
REMOTE CONTROL LCD AUTO OFF
To maximize battery life of the RF wireless remote control, the LCD of the remote control will be OFF if no key is pressed in 20 seconds. To re-activate the LCD display, press any key once to bring the remote control to normal operation.
www.aquaticav.com
8
LISTENING TO FM RADIO
ENTER FM RADIO MODE
1. Press (MODE) on remote control to switch to FM radio model.
If this is the first time you listen to FM radio, the default frequency will be 87.5MHz, as shown on the remote LCD.
FM radio is only available when you are in the FM Radio Mode.
TO SCAN OR NAVIGATE CHANNELS
1. Press (FAST REWIND) or (FAST FORWARD) to seek another station.
2. Press and hold either (FAST REWIND) or (FAST FORWARD) for manual tuning back or forward.
SAVING RADIO CHANNEL TO MEMORY
1. If you want to save the current frequency into memory, press and hold or or for more than 2 seconds. The station will be stored the to relevant button or or
LISTENING TO SAVED RADIO MEMORY
1. Press or or button once to listen to the station stored in button.
LOCATION OF CONTROLS
WATER/DUST PROOF DIGITAL MEDIA LOCKER™
Item Description
1.
2.
3.
4.
5.
6.
7.
Digital Media Locker Knob and Protective Door
ON/OFF Button
Water/Dust Protection Inner Gasket
3.5mm AUX Input Jack for MP3 Devices
ON/OFF Power LED
Security Strap for Digital Media Devices (MP3/iPod) iPod 30-pin Connector
7 www.aquaticav.com
www.aquaticav.com
4
5
LOCATION OF CONTROLS
RF LCD WIRELESS REMOTE CONTROL
Item Description
A.
B.
C.
Remote Control LCD
Remote Control Buttons
Battery Door
Press once: Enter BAS-TRE-BAL-FAD-DX-MONO-STEREO
Press and hold: Switch USA to EUR tuning
Press once: Enter BAS-TRE-BAL-FAD-DX-MONO-STEREO
Press and hold: Switch USA to EUR tuning
If your music player is not an iPod, you will only be able to use the volume and power controls on the remote control.
In order to prolong remote battery life the LCD will shut off after 20 seconds if no other button is pressed. To turn remote back on, press any button once, and then press the command desired.
www.aquaticav.com
LISTENING TO PLAYERS
LISTENING TO iPOD
1. Power up the Digital Media Locker™.
2. Attach your iPod device to the iPod 30-pin connector.
3. Secure the iPod device with the anchor straps provided.
4. Secure The Digital Media Locker™ protective door.
5. Press and hold (POWER) on the remote control to turn it ON.
6. Press (MODE) on the remote control to select iPod mode. Use the buttons below for
6.
the features.
Button Press once
Last Track
Press and Hold
Fast Rewind
Toggle Play and Pause
Next Track Fast Forward
If you are listening to iPod and you change your mode to Radio or Standby mode, the iPod will automatically pause playing and the charging screen will appear.
The remote control will only allow navigation of songs within the selected playlist. To navigate to another playlist use the iPod directly.
Always ensure to connect and disconnect your media player with dry hands.
LISTENING TO MP3
1. Power up the Digital Media Locker™.
2. Attach your MP3 device to the 3.5mm connector.
3. Secure the MP3 device with the anchor straps provided.
4. Secure The Digital Media Locker™ protective door.
5. Press and hold (POWER) on the remote control to turn it ON.
6. Press (MODE) on the remote control to select AUX mode. RF wireless remote
6. control of Volume only.
ADJUSTING VOLUME LEVEL
1. Press (VOLUME UP) once to increase the volume by 3 decibels.
2. Press (VOLUME DOWN) once to reduce the volume by 3 decibels.
3. Press and hold either VOLUME UP or VOLUME DOWN and the Digital Media Locker™
3. will increase or decrease the volume continuously.
www.aquaticav.com
6
5
LOCATION OF CONTROLS
RF LCD WIRELESS REMOTE CONTROL
Item Description
A.
B.
C.
Remote Control LCD
Remote Control Buttons
Battery Door
Press once: Enter BAS-TRE-BAL-FAD-DX-MONO-STEREO
Press and hold: Change USA to EUR
If your music player is not an iPod, you will only be able to use the volume and power controls on the remote control.
In order to prolong remote battery life the LCD will shut off after 20 seconds if no other button is pressed. To turn remote back on, press any button once, and then press the command desired.
www.aquaticav.com
LISTENING TO PLAYERS
LISTENING TO iPOD
1. Power up the Digital Media Locker™.
2. Attach your iPod device to the iPod 30-pin connector.
3. Secure the iPod device with the anchor straps provided.
4. Secure The Digital Media Locker™ protective door.
5. Press and hold (POWER) on the remote control to turn it ON.
6. Press (MODE) on the remote control to select iPod mode. Use the buttons below for
6.
the features.
Button Press once
Last Track
Press and Hold
Fast Rewind
Toggle Play and Pause
Next Track Fast Forward
If you are listening to iPod and you change your mode to Radio or Standby mode, the iPod will automatically pause playing and the charging screen will appear.
The remote control will only allow navigation of songs within the selected playlist. To navigate to another playlist use the iPod directly.
Always ensure to connect and disconnect your media player with dry hands.
LISTENING TO MP3
1. Power up the Digital Media Locker™.
2. Attach your MP3 device to the 3.5mm connector.
3. Secure the MP3 device with the anchor straps provided.
4. Secure The Digital Media Locker™ protective door.
5. Press and hold (POWER) on the remote control to turn it ON.
6. Press (MODE) on the remote control to select AUX mode. RF wireless remote
6. control of Volume only.
ADJUSTING VOLUME LEVEL
1. Press (VOLUME UP) once to increase the volume by 3 decibels.
2. Press (VOLUME DOWN) once to reduce the volume by 3 decibels.
3. Press and hold either VOLUME UP or VOLUME DOWN and the Digital Media Locker™
3. will increase or decrease the volume continuously.
www.aquaticav.com
6
7
LISTENING TO FM RADIO
ENTER FM RADIO MODE
1. Press (MODE) on remote control to switch to FM radio model.
If this is the first time you listen to FM radio, the default frequency will be 87.5MHz, as shown on the remote LCD.
FM radio is only available when you are in the FM Radio Mode.
TO SCAN OR NAVIGATE CHANNELS
1. Press (FAST REWIND) or (FAST FORWARD) to seek another station.
2. Press and hold either (FAST REWIND) or (FAST FORWARD) for manual tuning back or forward.
SAVING RADIO CHANNEL TO MEMORY
1. If you want to save the current frequency into memory, press and hold or or for more than 2 seconds. The station will be stored the to relevant button or or
LISTENING TO SAVED RADIO MEMORY
1. Press or or button once to listen to the station stored in button.
SWITCH BETWEEN US & EURO FM MODES
1. Make sure dock and remote are turned on and in ‘RADIO’ mode.
2. Hold down the (AUDIO) button for 3-5 seconds.
3. The remote will display ‘AREA USA’ or ‘AREA EUR’ depending on which tuning mode is currently selected.
4. Use the +/- arrows to switch between US or European modes.
5. Press (PLAY/PAUSE) to select the desired tuning mode.
6. Once you switch modes it will default to the FM station stored in ‘PRESET 1’.
US mode will increase and decrease the FM frequency in steps of 0.1 MHz, e.g. 88.5,
88.6, 88.7 MHz. EUR mode will increase and decrease the FM frequency in steps of
0.05 MHz, e.g. 88.25, 88.30, 88.35 MHz.
www.aquaticav.com
LOCATION OF CONTROLS
WATER/DUST PROOF DIGITAL MEDIA LOCKER™
Item Description
1.
2.
3.
4.
5.
6.
7.
Digital Media Locker Knob and Protective Door
ON/OFF Button
Water/Dust Protection Inner Gasket
3.5mm AUX Input Jack for MP3 Devices
ON/OFF Power LED
Security Strap for Digital Media Devices (MP3/iPod) iPod 30-pin Connector www.aquaticav.com
4
3
GETTING STARTED
REMOTE BATTERY INSTALL
Remove the water/dust proof RF wireless remote control from the Digital Media Locker™.
Unscrew the waterproof cap on the back of the remote control and place the CR-2430 battery in the RF remote control and replace the water/dust proof cap.
POWER ON
To activate the Digital Media Locker™ press the on/off button. ON will be indicated by a red
LED.
For applications that require zero current draw the power button must be turned OFF.
When the power button is in the OFF position the red LED will not be lit.
REMOTE SYNCHRONIZING
1. Turn the docking station OFF with the on/off button inside the door (the red LED should not be illuminated when power is OFF).
2. Press the red (POWER) button on the remote.
3. Press and hold the (MODE) button on the top right corner until the LCD reads PAIR.
4. Turn the docking station ON (within 10 seconds) with the on/off button inside door (the red LED will illuminate when power is ON).
5. The remote’s LCD should read WELCOME or show a mode position such as RADIO,
IPOD, or AUX IN.
If the pairing process is not effective, turn the docking station OFF with the on/off button, located inside the door of the dock. Uplug the 12-pin harness on the back of the stereo for 3 minutes. Reattach the harness and repeat steps 1-5 above.
If the LCD displays “- -” in either mode, this means that your remote control is out of reception range. Please move closer and try the feature again.
Each Digital Media Locker™ comes with a matching RF (Radio Frequency) Wireless LCD remote control. This remote is required to use any functions on the unit. For any additional remote controls you will need to activate/synchronize those remote controls to the AQ-DM-4 by following the steps above.
If you lose your remote control and buy a replacement, follow the steps above to pair/synchronize before normal usage.
www.aquaticav.com
OTHER FEATURES
EXTERNAL TRIGGER
Aquatic AV understands the need for more flexible remote applications. With the Digital
Media Locker™ Aquatic AV has provided an independent 12V “accessory” trigger, activated from the RF wireless remote that allows the user to activate non-iPod, MP3 related devices.
This could include and 12V based device like 12V lights or surveillance camera.
1. In any operational mode, press the (12V TRIGGER) key to activate. Press again to deactivate.
2. We strongly recommend you speak to our technical service staff or your dealer if you are considering using this feature.
Load on External Trigger should not exceed 350mA iPOD CHARGING
When specified iPod devices are connected to the Digital Media Locker™ 30-pin connector the iPod battery will charge.
To avoid rusting as a result of electrical potential in the connector, the battery of your iPod devices must not be totally drained. If your iPod is not charged at all then the
Digital Media Locker will not charge it.
REMOTE CONTROL LCD AUTO OFF
To maximize battery life of the RF wireless remote control, the LCD of the remote control will be OFF if no key is pressed in 20 seconds. To re-activate the LCD display, press any key once to bring the remote control to normal operation.
www.aquaticav.com
8
9
SPECIFICATIONS
TECHNICAL SPECIFICATION
General
Power Supply:
Current drain when OFF:
Remote Control Frequency:
Remote Control Battery:
External Trigger:
IP Rating (Digital Media Locker™):
UV Protection:
FM Radio
FM Radio Sensitivity:
FM Antenna:
FM Radio Reception:
Number of Radio Presets:
Amplifier
Distortion:
Frequency Response:
Amplifier Output:
10.7V - 15.6V DC, 5A min
0A
2.4GHz
3V (1 x CR2430 battery)
12V DC, 350mA max
IP65
500 hours stable without degradation
8uV
Dipole Antenna (not included)
Stereo
3
<0.1% THD at 1kHz
20Hz - 20kHz
45W per channel at 4 Ohm load
72W per channel at 2 Ohm load www.aquaticav.com
F
GETTING STARTED
12-PIN HARNESS
The AQ-DM-4 will require a universal harness (AQ-UNH-2) in order to connect the dock to power and speakers.
All open wire connections should be soldered and protected against water and dust for best long term performance.
Speaker
Right
Rear
RR (Pin 11) (Purple/Black Stripe)
RR (Pin 12) (Purple)
DC Ground (Pin 10) (Black)
Right
Front
RF (Pin 8) (Gray/Black Stripe)
RF (Pin 9) (Gray)
+12VDC, Triggered (Pin 6) (Blue)
Not Used (Pin 6)
+12VDC (Pin 1) (Red)
Left
Rear
LR (Pin 3)
LR (Pin 2)
(White/Black Stripe)
(White)
Left
Front
LF (Pin 5)
LF (Pin 5)
(Green/Black Stripe)
(Green)
No lower than a 2 Ohm load should be used or damage may occur to the Digital Media Locker ™.
Make sure the polarity of speakers are connected correctly.
MOUNTING THE UNIT
1. Mounting templates are included. Aquatic AV recommends
1. using the ‘measure twice, cut once’ method.
2. Once the mounting hole is complete, make sure the outside
2. surface is clean and clear of debris. The Digital Media
2.
Locker™ has an external water/dust proof gasket, but this
2. requires a clean surface for best performance.
3. The Digital Media Locker™ has six(6) front screws. Drive
2.
the 6 screws using a screw driver. During final mounting,
3.
apply equal pressure to all points for the best water/dust
3..
outer seal performance.
4. Review all outside surfaces of the Digital Media Locker™ to
4. ensure proper water/dust seal. This is important for long
4.
term environmental protection performance for iPod or MP3
4. devices.
www.aquaticav.com
2
1
GETTING STARTED
CONTENTS
• AQ-DM-4 Digital Media Locker™
• 2-way RF wireless remote control
• 2.35m audio cable (3.5mm plug to 3.5mm plug)
• One (1) CR2430 battery
• AQ-DM-4 mounting template
• Six (6) Stainless Steel mounting screws
• Owners manual
INSTALLATION
1. 12-pin Watertight Harness
This harness supplies power and ground connections to the Digital Media Locker™ and four (4) speaker channel output connections from the Digital Media Locker™. The AQ-UNH-2 (supplied separately) or a custom manufacture harness will be required.
Do not cut or modify the 12-pin harness or warranty will be void
2. FM Radio Antenna Jack
Connect antenna to female antenna receptacle. For best FM performance make sure the FM
Antenna is extended to the highest achievable position.
3. Auxiliary Input
The AQ-DM-4 has a 3.5mm stereo jack socket for connecting other audio devices.
4. Auxiliary Outputs
Allows external amplifier to be connected to power additional speakers.
5. 12V DC External Trigger
Allows for an external light or relay to be triggered (350mA max load).
FM Radio
Antenna Jack
Aux’ Input
Jack Socket
12 pin
Harness Cable
Left Audio - RCA Output Jack
Right Audio - RCA Output Jack
External 12V Trigger (Brown) www.aquaticav.com
FCC STATEMENT
FCC ID:
MADE IN CHINA
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE:
The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
- Reorientate or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.
Product design and specification subject to change without notice. E&OE.
Digital Media Locker™ is a Trademark of Aquatic AV.
iPod is a Trademark of Apple Inc, registered in the US and other countries.
www.aquaticav.com
10
products with a watertight reputation
WATER/DUST PROOF DIGITAL MEDIA LOCKER™
AQ-DM-4
OWNERS MANUAL
Aquatic AV
282 Kinney Dr..
San Jose, CA 95112, USA
E-mail: [email protected]
US & Canada: 1 877 579 2782
International: +1 408 559 1668
Fax: +1 408 559 0125 www.aquaticav.com
products with a watertight reputation
WATER/DUST PROOF iPOD/MP3 DIGITAL MEDIA LOCKER™
WITH FLOATING RF LCD 2-WAY WIRELESS REMOTE CONTROL
PLEASE READ THIS INSTRUCTION MANUAL BEFORE
INSTALLATION AND OPERATION
advertisement
Related manuals
Frequently Answers and Questions
What is the power requirement for the remote control of Aquatic AQ-DM-1R?
Is it necessary for the speakers to have a 2 Ohm load impedance?
How do I turn on the Aquatic AQ-DM-1R?
How do I synchronize the remote control with the Aquatic AQ-DM-1R?
What is the process for listening to an iPod device with the Aquatic AQ-DM-1R?
advertisement