Cisco Explorer 8540HDC Operating instructions

Notice to Installers
The servicing instructions in this notice are for use by qualiÞed service personnel only. To reduce risk of electric shock, do not perform any servicing other than that contained in
the operating instructions, unless you are qualiÞed to do so.
Quick Reference Guide
Note to System Installer
For this apparatus, the coaxial cable shield/screen shall be grounded as close as
practical to the point of entry of the cable into the building.For products sold in the
US and Canada, this reminder is provided to call the system installer's attention to
Article 820-93 and Article 820-100 of the NEC (or Canadian Electrical Code Part 1),
which provides guidelines for proper grounding of the coaxial cable shield.
CAUTION: To reduce the risk of electric shock, do not remove cover (or back).
No user-serviceable parts inside. Refer servicing to qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
This symbol is intended to alert you that uninsulated voltage within this product
may have sufficient magnitude to cause electric shock.Therefore, it is dangerous
to make any kind of contact with any inside part of this product.
Ce symbole a pour but d’alerter toute personne qu’un contact avec une pièce
interne de ce produit, sous tension et non isolée, pourrait être suffisant pour
provoquer un choc électrique. Il est donc dangereux d’être en contact avec toute
pièce interne de ce produit.
Explorer 8540HDC DVR and 8550HDC DVR
with Multi-Stream CableCARD Interface
This symbol is intended to alert you of the presence of important operating and
maintenance (servicing) instructions in the literature accompanying this product.
Ce symbole a pour but de vous avertir qu’une documentation importante sur le
fonctionnement et l’entretien accompagne ce produit.
20070131 SysInstaller 820 US/Canada/Intl
IMPORTANT SAFETY INSTRUCTIONS
Read These Instructions
Keep These Instructions
Heed All Warnings
Follow All Instructions
Power Source Warning
A label on this product indicates the correct power source for this product. Operate this product only from an electrical
outlet with the voltage and frequency indicated on the product label. If you are uncertain of the type of power supply to
your home or business, consult your service provider or your local power company.
The AC inlet on the unit must remain accessible and operable at all times.
Ground the Product
WARNING:
Avoid electric shock and Þre hazard! Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades
and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug
does not Þt into your outlet, consult an electrician for replacement of the obsolete outlet.
If this product connects to coaxial cable wiring, be sure the cable system is grounded (earthed). Grounding provides
some protection against voltage surges and built-up static charges.
Outdoor Grounding System
If this product connects to an outdoor antenna or cable system, be sure the antenna or cable system is grounded
(earthed). This provides some protection against voltage surges and built-up static charges.
Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990, provides the following information:
Verify the Power Source from the On/Off Power Light
SELECT
CH-
GUIDE
INFO
EXIT
LIST
L AUDIO IN R
VIDEO IN
Prevent Power Cord Damage
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point
where the cord exits from the apparatus.
Provide Ventilation and Select a Location
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• Do not place this apparatus on a bed, sofa, rug, or similar surface.
• Do not place this apparatus on an unstable surface.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliÞers) that produce heat.
Check Product Safety
Upon completion of any service or repairs to this product, the service technician must perform safety checks to
determine that this product is in proper operating condition.
Protect the Product when Moving It
• Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or other objects on
top of this product.
Always disconnect the power source when moving the apparatus or connecting or disconnecting cables.
Protect from Exposure to Moisture and Foreign Objects
Do not use this apparatus near water.
WARNING:
Avoid personal injury and damage to this product! Use only with the cart, stand, tripod,
bracket, or table speciÞed by the manufacturer or sold with the apparatus. When a cart is
used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
20070320 Set-Top Cable US & Canada
FCC Compliance
United States FCC Compliance
Protect the Product from Lightning
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
Disclaimer
ScientiÞc-Atlanta, Inc. assumes no responsibility for errors or omissions that may appear in this guide. ScientiÞc Atlanta
reserves the right to change this guide at any time without notice.
AVC VIDEO LICENSE
With respect to each AVC/MPEG-4/H.264 product, ScientiÞc Atlanta is obligated to provide the following notice:
WARNING:
Avoid electric shock and Þre hazard! Do not expose this product to liquids, rain, or moisture.
WARNING:
Avoid electric shock and Þre hazard! Unplug this product before cleaning. Clean only with a dry cloth. Do
not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning device (dust remover)
to clean this product.
Canada EMI Regulation
20060628 FCC Standard
• Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation provides proper ventilation.
• Requirements for the grounding electrodes (see the following antenna grounding diagram as recommended by
NEC ANSI/NFPA 70)
For added protection, unplug this apparatus during lightning storms or when unused for long periods of time. In
addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.
VOL+
POWER
WARNING:
Avoid electric shock and Þre hazard! Do not overload AC mains, outlets, extension cords, or integral
convenience receptacles. For products that require battery power or other power sources to operate them,
refer to the operating instructions for those products.
• Connection to grounding electrodes
WARNING:
Avoid electric shock and Þre hazard! Do not locate an outside antenna system in the vicinity of overhead
power lines or power circuits. Touching power lines or circuits might be fatal.
VOL-
Eliminate AC Mains Overloads
• Grounding the lead-in wire to an antenna discharge unit
• Location of the antenna-discharge unit
CH+
When the on/off power light is not illuminated, the apparatus may still be connected to the power source. The light
goes out when the apparatus is turned off, regardless of whether it is still plugged into an AC power source.
• Grounding of the mast and supporting structure
• Size of the grounding conductors
EXPLORER® 8550HDC™
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged
to try to correct the interference by one or more of the following measures:
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD
(“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A
PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED
TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.
Accordingly, please be advised that service providers, content providers, and broadcasters are required to obtain a
separate use license from MPEG LA prior to any use of AVC/MPEG-4/H.264 encoders and/or decoders.
• Reorient or relocate the receiving antenna, if applicable.
WARNING:
Avoid electric shock and Þre hazard! Never push objects through the openings in this product. Foreign
objects can cause electrical shorts that can result in electric shock or Þre.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the cable company or an experienced radio/television technician for help.
Accessories Warning
WARNING:
Avoid electric shock and Þre hazard! Only use attachments/accessories speciÞed by your service provider
or the manufacturer.
Service Warnings
WARNING:
Avoid electric shock! Do not open the cover of this product. Opening or removing the cover may expose
you to dangerous voltages. If you open the cover, your warranty will be void. This product contains no
user-serviceable parts. Refer all servicing to qualiÞed service personnel.
Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Any changes or modiÞcations not expressly approved by ScientiÞc-Atlanta, Inc., could void the user’s authority to
operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the FCC and is intended
to supply you with information regarding the FCC approval of this device. The phone numbers listed are for FCC-related
questions only and not intended for questions regarding the connection or operation for this device. Please contact your
cable service provider for any questions you may have regarding the operation or installation of this device.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) the device
may not cause harmful interference, and 2) the device must accept any interference received, including interference
that may cause undesired operation.
Explorer 8540HDC and 8550HDC Digital Video Recorder
Model: 8540HDC and 8550HDC
Manufactured by: ScientiÞc-Atlanta, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 770-236-1077
ScientiÞc Atlanta, A Cisco Company
5030 Sugarloaf Parkway, Box 465447,
Lawrenceville, GA 30042
770.236.5000
www.scientiÞcatlanta.com
ScientiÞc Atlanta, the ScientiÞc Atlanta logo, and Explorer are registered trademarks of ScientiÞc-Atlanta, Inc.
8540HDC and 8550HDC are trademarks of ScientiÞc-Atlanta, Inc.
Cisco, the Cisco logo, and Cisco Systems are trademarks or registered trademarks of Cisco Systems, Inc. and/or its afÞliates in the
U.S. and certain other countries.
CableCARD and M-Card are trademarks of Cable Television Laboratories, Inc.
Dolby is a registered trademark of Dolby Laboratories.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are registered trademarks of Dolby Laboratories.
HDMI, the HDMI logo, and High-DeÞnition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Macrovision is a registered trademark of Macrovision Corp.
All other trademarks shown are trademarks of their respective owners.
Product and service availability is subject to change without notice.
© 2007 ScientiÞc-Atlanta, Inc. All rights reserved.
September 2007
Printed in United States of America
Part Number 4012390 Rev A
Welcome
Explorer 8550HDC Front Panel
The Explorer® 8540HDC™ and 8550HDC™ DVR Set-Top with a
Multi-Stream CableCARD™ (M-Card™) delivers high-deÞnition
programming in exceptional picture and audio quality. The M-Card
provides system security and authorization of digital services.
Through these DVR set-tops, you can access interactive services,
such as video-on-demand and pay-per-view programs. Contact your
service provider for information about these and other available
services. Use the instructions in this guide to install the 8540HDC or
8550HDC and to access your program services.
Connection Example
EXPLORER® 8550HDC™
Note: This illustration
may vary from the
actual product.
CH+
VOL-
VOL+
POWER
SELECT
CH-
GUIDE
INFO
EXIT
23
4
5
12
Turns the DVR on and off
For more information about this product, visit our website:
2 USB
Connects to external USB devices (Reserved for future use)
www.scientiÞcatlanta.com/products/consumers/new_cableboxes.htm
3 VOL +, VOL -
Increases and decreases the volume
4 CH+, CH -
Scrolls through the channels
5 Select
Accesses your on-screen selection
6 IR Sensor
Receives the infrared signal from the remote control
7 LED Display
Displays the selected channel number and time of day. The LED also displays the following:
Watch TV
Press the following remote control keys to access services and
programs:
• Guide–Display the on-screen program guide
• Arrows–Highlight a program in the schedule
• Info–Display program description
• Select–Watch a speciÞc program in the guide
Avoid Screen Burn-In!
Images such as letterbox bars or side bars, bright closed-captioning
backgrounds, station logos, or any other stationary images may
cause the HDTV screen to age unevenly and cause damage to your
HDTV. Refer to the user’s guide that came with your HDTV for more
information about screen burn-in.
•
•
•
•
•
THIS DEVICE IS INTENDED TO BE ATTACHED TO A
RECEIVER THAT IS NOT USED TO RECEIVE OVER-THE-AIR
BROADCAST SIGNALS. CONNECTION OF THIS DEVICE
IN ANY OTHER FASHION MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS
AND IS IN VIOLATION OF THE FCC RULES, PART 15.
T13158
1 Power
Before using this DVR read the IMPORTANT SAFETY
INSTRUCTIONS section of this guide.
SCIENTIFIC-ATLANTA, INC.
Displays a description of the selected program. This button is available
from the on-screen guide and while viewing a program
Safety and Performance Tips
• Keep the top of the DVR free of all objects
and electronic devices, including your TV.
10 Exit
Exits menus, the on-screen guide, and program information
11 List
Displays the Recorded List
12 Video and
Audio Input
Not available on all models. Connects to video and left/right (L/R) audio
outputs from a TV or other device. (Not available on 8540HDC)
CABLE
IN
WARNING:
Electric shock hazard!
Unplug all electronic
devices before connecting
or disconnecting any device
cables to the DVR.
• Always set the DVR on its feet, never on
its side.
R
R
Pr
R
USB 2.0
120 VAC
60Hz 4.2A
500W
1394 1394
eSATA
120VAC
60Hz 80W
LISTED 14H1
VIDEO PRODUCT
AUDIO
CENTER
CHANNEL IN
DVI/HDCP
IN
Back of
HDTV
OFF
S-VIDEO
R
L
ANT (75 )
VIDEO
Y
VIDEO
PB
L
PR
AUDIO
Y
L/
MONO
PB
L
R
PR
AUDIO
R
VIDEO
STB SN: SABPQBQGD
OUT 1
VIDEO Y
DIGITAL
AUDIO
OPTICAL
AUDIO
OUT
MULTI-STREAM CABLE CARD
ANT-1
OUT
R
HD 2
M-CARD SN: PKCPKPDBT
STB RF MAC: 001AC3F$F756
THIS DEVICE IS INTENDED TO BE ATTACHED TO A
RECEIVER THAT IS NOT USED TO RECEIVE OVER-THE-AIR
BROADCAST SIGNALS. CONNECTION OF THIS DEVICE
IN ANY OTHER FASHION MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS
AND IS IN VIOLATION OF THE FCC RULES, PART 15.
L
L
Pb
L
R
R
Pr
R
CATV CONVERTER
MADE IN MEXICO
AVIS: RISQUE DE CHOC
ELECTRIQUE NE PAS OUVRIR
M-CARD MAC: 001AC326910A
IR
CABLE OUT
USB 2.0
eSATA
120 VAC
60Hz 4.2A
500W
1394 1394
S-VIDEO
OUT
1 Cable In
2 Set-Top Bar Code Label Contains set-top serial number and MAC addresses
Note: This illustration
may vary from the
actual product.
120VAC
60Hz 80W
LISTED 14H1
VIDEO PRODUCT
3 4 5 6 7 8 9 11 13 14 16 17 19 20 21 22
10 12
15
18
• Verify that the M-Card module is installed.
• Verify that the power to your TV is turned on.
• If the DVR is plugged into a wall switch, verify the switch is in the
ON position. (Avoid plugging into an outlet that is controlled by a
wall switch.)
• Verify that all cables are properly connected.
• The current channel may not be available in your service
package.
Try selecting another channel to see if a picture appears.
T13200
Connects to a coaxial cable that delivers the signal from your service provider
3 Archive Video
Connects to a video input of an archive device
IN
OUT
IN
ANT-2
T13201
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
eCM MAC: 001AC3F4F757
2
CABLE OUT
HD 1
ARCHIVE
1
ELECTRIQUE NE PAS OUVRIR
S-VIDEO
OUT
IN
CABLE
IN
AVIS: RISQUE DE CHOC
M-CARD MAC: 001AC326910A
IR
R
No picture
• If your setup includes a VCR or stereo, verify that you have
properly connected them to the DVR.
• Verify the volume is turned up.
• Verify the mute function is not on.
L
L/
MONO
Explorer 8550HDC Back Panel
If the DVR does not perform as expected, the following tips may help.
No sound
Pb
AUDIO
Performance Tips
• Verify that the HDTV is in HD mode. If necessary, re-run the
HDTV Setup Wizard to select HD mode.
• Verify the current TV program is broadcast in color.
• Adjust the TV color controls.
L
CATV CONVERTER
MADE IN MEXICO
Automatic Software Updates
No color
L
AUDIO IN
DVI/HDCP
9 Info
SCIENTIFIC-ATLANTA, INC.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ON
Accesses the on-screen guide, video-on-demand, or pay-per-view features
Note: If you need further assistance, contact your service provider.
MULTI-STREAM CABLE CARD
Cable
Input
Message (
)
HDTV
Power (
)
Output Resolution (1080i, 720p, 480p, or 480i)
AUTO - Automatically outputs native scan rates that your TV can accept
8 Guide
A message appears on the TV screen when the DVR and the
M-Card module are receiving software updates. In addition,
download information appears on the front panel of the DVR during
these updates. Wait for the current time to appear on the front panel
before continuing. When the time appears, the update is complete.
OPTICAL
AUDIO
OUT
VIDEO IN
Important! If the M-Card is removed, the set-top will not operate
correctly.
Safety First
DIGITAL
AUDIO
M-CARD SN: PKCPKPDBT
STB RF MAC: 001AC3F$F756
6 7 8 9 1011
OUT 1
VIDEO Y
VIDEO
eCM MAC: 001AC3F4F757
LIST
L AUDIO IN R
1
ARCHIVE
STB SN: SABPQBQGD
4 L-R Audio Archive
Connects to an audio input of an archive device
5 Video 1 (Composite)
Connects to a video input of another device, such as a TV or VCR
6 Audio Out (Left/Right)
Connects to RCA cables that send analog audio signals (left/right) to a stereo receiver or TV with stereo inputs
7 YPbPr
Connects to the component video input (YPbPr) on an HDTV. Do not use these cables if you are using the
HDMI connection
8 Out 2 (Secondary
Audio Out)
Connects to either a VCR or to another set of inputs (composite) on your TV
9 Digital Audio Out
Connects to an RCA cable that sends a digital audio signal to a surround-sound receiver or other digital audio device
10 S-Video Out
Connects to S-Video input of a standard TV or VCR
11 IR
Connector reserved for future use
12 Optical Audio Out
Connects to an optical cable that sends a digital audio signal to a surround-sound receiver or other digital audio device
13 Cable Out
Connects to a coaxial cable that sends analog audio and video signals to a TV or VCR. These signals are
SDTV video and stereo audio
14 HDMI
Connects an HDMI™ cable to the HDMI input of an HDTV. HDMI supports both digital audio and video. May be used
to connect to a DVI interface using an HDMI-to-DVI adapter for video and separate audio connections. Any of the
following audio connections may be used: Digital Audio Out (9); Audio Out: Left, Right (6); or Optical Audio Out (12)
15 M-CARD
Installed by your service provider
16 USB 2.0
Connects to external USB devices (Reserved for future use)
17 eSATA
Connects to an external Serial ATA (eSATA) hard disk drive for expanded drive space. A connected eSATA drive is
not an archival device. Ask your service provider for a list of approved hard drive models for use with the DVR
18 M-CARD Code Label
Contains M-CARD serial number and MAC address
19 1394
Connects to display devices equipped with a 1394 input
20 Ethernet
Connects to an Ethernet-equipped device (Reserved for future use)
21 AC Outlet
Connects to the AC power cord from another device, such as a TV
22 AC Power Input
Connects to the power cord to deliver power to the set-top
Connecting to an HDTV with Component Input (YPbPr)
1. Insert the M-Card module if not already installed.
2. Connect the DVR to the coaxial cable coming from the wall.
3. Connect the Y (green) connector on the HDTV to the Y (green) connector on the DVR; connect the Pb (blue) connector on the HDTV to the Pb
(blue) connector on the DVR; and connect the Pr (red) connector on the HDTV to the Pr (red) connector on the DVR.
4. Connect the left audio (white) connector on the HDTV to the left audio (white) connector on the DVR, and connect the right audio (red)
connector on the HDTV to the right audio (red) connector on the DVR.
5. Plug the DVR and the HDTV into an AC power source. Do not press the Power key on the DVR yet.
Important: To potentially protect the DVR from power surge damage, ground (earth) your cable product to provide some protection against
voltage surges and built-up static charges. You may be able to reduce the risk of damage from voltage surges, which can be caused by
lightning storms and power outages, by plugging the DVR into a surge protector.
6. Wait several minutes for the DVR to receive the latest software, programming, and service information. One of the following will appear on
the front panel of the DVR:
• Current time: The update is complete.
• Four dashes (----): Call your service provider to get the DVR authorized.
7. To begin watching TV, turn on the HDTV and press Power on the front panel of the DVR, or press Power on the remote control.
U.S. Patents
A patent notice is afÞxed to this product. In addition, the product may also be covered by one or more of the following patents:
4,498,169, 4,692,919, 4,748,667; 4,829,569; 4,866,770; 4,885,775; 4,888,799; 4,890,319; 4,922,456; 4,922,532; 4,924,498; 4,965,534; 4,991,011; 5,003,384; 5,012,510; 5,029,207;
5,045,816; 5,053,883; 5,054,071; 5,058,160; 5,142,575; 5,142,690; 5,146,526; 5,155,590; 5,214,390; 5,225,902; 5,225,925; 5,235,619; 5,237,610; 5,239,540; 5,241,610; 5,247,364;
5,255,086; 5,257,403; 5,267,071; 5,270,809; 5,271,041; 5,272,752; 5,282,028; 5,285,497; 5,287,351; 5,301,028; 5,309,514; 5,317,391; 5,319,709; 5,341,425; 5,347,388; 5,347,389;
5,357,276; 5,359,601; 5,361,156; 5,367,571; 5,379,141; 5,379,145; 5,381,481; 5,390,337; 5,400,401; 5,406,558; 5,418,782; 5,420,866; 5,420,923; 5,425,101; 5,428,404; 5,430,568;
5,434,610; 5,436,749; 5,438,370; 5,440,632; 5,442,472; 5,455,570; 5,457,701; 5,471,492; 5,477,199; 5,477,262; 5,477,282 5,477,370; 5,481,389; 5,481,542; 5,485,221; 5,493,339;
5,497,187; 5,500,758; 5,502,499; 5,506,904; 5,519,780; 5,539,822; 5,550,825; 5,579,055; 5,579,057; 5,583,562; 5,592,551; 5,596,606; 5,600,378; 5,602,933; 5,640,388; 5,657,414;
5,675,575; 5,684,876; 5,715,515; 5,724,525; 5,734,822; 5,740,300; 5,742,677; 5,754,940; 5,757,416; 5,771,064; 5,774,859; 5,825,829; 5,826,167; 5,850,305; 5,854,703; 5,870,474;
5,892,607; 5,920,626; 5,923,755; 5,930,024; 5,930,515; 5,937,067; 5,963,352; 5,966,163; 5,982,424; 5,991,139; 5,999,207; 6,005,631; 6,005,938; 6,016,163; 6,028,941; 6,029,046;
6,052,384; 6,055,244; 6,072,532; 6,105,134; 6,148,039; 6,157,719; 6,188,729; 6,195,389; 6,212,278; 6,215,530; 6,219,358; 6,240,103; 6,243,145; 6,246,767; 6,252,964; 6,272,226;
6,292,081; 6,292,568; 6,320,131; 6,374,275; 6,405,239; 6,411,602; 6,417,949; 6,424,714; 6,424,717; 6,433,906; 6,438,139; 6,463,586; 6,467,091; 6,476,878; 6,493,876; 6,510,519;
6,516,002; 6,516,412; 6,526,508; 6,538,595; 6,546,013; 6,560,340; 6,567,118; 6,570,888; 6,622,308; 6,629,227; 6,664,984; 6,667,994; 6,671,879; 6,674,967; 6,678,891; 6,714,598;
6,721,352; 6,721,956; 6,725,459; 6,738,982; 6,744,892; 6,744,967; 6,751,271; 6,760,918; 6,795,972; 6,802,077; 6,804,708; 6,811,447; 6,817,028; 6,822,972; 6,823,385; 6,832,386;
6,845,106; 6,868,473; 6,874,075; 6,889,191; 6,909,471; 6,917,622; 6,917,628; 6,922,412; 6,927,806; 6,928,656; 6,931,058; 6,937,729; 6,969,279; 6,971,008; 6,971,121; 6,978,310;
6,986,156; 6,988,900; 6,996,838; 7,010,801; 7,053,960; 7,065,213; 7,069,578; 7,069572; D348065; D354959; D359737; D363932; D390217; D434753; D507240; D507535;
D513407; D516518; RE36368; RE36988
20070417 Patents