Siemens 4015 Operating instructions

7LF4 4015
GB
R
c
1400VA
1
1x 58W ≤ 7μF
3600W
2
+
1200W
100W
5
4
3
1800W
+
+
1800W
2300W
Safety notes
This product may be installed only by a qualified electrician. Non-compliance may result in a fire hazard or electric shocks. Before installation, read
the operating instructions and observe the product-specific requirements for the installation location. Use only original spare parts for repair and
maintenance. Unauthorised opening and repair by other persons will invalidate all claims for liability, replacement or warranty services.
Technical Data
Supply voltage:
110 / 240V 50/60Hz
Operating temperature: - 10°C to +55°C
Power consumption:
< 0,1 W
Storage temperature: - 10°C to +60°C
Relay output:
1 changeover contact 16A 250V~ cos ϕ = 1
Operating principle:
Accuracy:
± 1 s /day at 25°C
Type 1.B. S. T. IEC/EN 60730-1,
IEC/EN 60730-2-7
single-strand
multi-strand
Operation in a normal environment
Wire cross-sections:
1,5...4 mm2
1,5...2,5 mm2
Degree of contamination: 2
Program blocks:
28 adjustable
Battery reserve:
6 years
Operating modes:
Mains power (the relay does not switch in the event of a power failure)
Installation:
in distribution panel
Battery operation, full operation without mains power.
5-way switch
1
Flashing cursor indicates day
and time
2
Day of the week
0
1234567
Opens menu selection.
Confirm a selection or apply the parameters
(OK).
Program overview
12
ON
Select the options or set the parameters.
Relay status display
5-way switch
5
4
3
Set and enable/disable the switching times.
292350/01
OFF
251426.41.19 “02”
24
Current time
Setting the time
MIN
HOUR
EXIT
TIME
DATE
SU WI
PROG
MIN
HOUR
Setting the date
EXIT
TIME
DATE
SU WI
PROG
EXIT
TIME
DATE
SU WI
PROG
YEAR
MON
YEAR
DAY
MON
DAY
Changing to summer time +1h
EXIT
TIME
DATE
SU WI
PROG
EXIT
TIME
DATE
SU WI
PROG
EU
US
NO
SPEC
Setting
EU
US
NO
SPEC
MON.
END
DAY
STRT
Applies to
EU
Last Sunday
in October
European
Union
US
Second
Sunday in
March
First Sunday
in November
North America
NO
No change
No change
Freely programmable summer time/winter time
changeover date
Enter the summer time starting date and ending
date in your location or country here. The corresponding day of the week will be determined automatically from the date entered.
The system also determines whether the day of the
week falls in the first, second, third or last week of
the month.
The change will take place on the same day of the
week in the corresponding week each year.
YEAR
STRT
MON.
STRT
Summer
time ends
Last Sunday
in March
SPEC
YEAR
STRT
Summer
time begins
MON.
END
DAY
END
Programming
Programming is carried out in the same way as with a mechanical timer. Programming can be done in either mains or battery power mode.
After setting a program, press the OK button
to save it and view it in the program overview (see page 1). If no buttons are pressed for
1 minute during programming, the current program will be saved.
1234567
EXIT
TIME
DATE
SU-WI
PROG
EXIT
TIME
DATE
SU WI
PROG
0
MEMO
FULL
12
24
28 programs have been
stored. No more programs
can be added.
ON
OFF
Virtually turn the dial to select the switch-on time first, e.g. Monday 06.15
0
1234567
12
Use
to select the hour, in this case 6. Then use
to set the minutes.
24
Use
OFF
0
Hold down the 5-way switch
Use
ON
to enable the switch-on period, e.g. Monday 6:15 until Monday 10:00
to program in 15-minute increments.
1234567
12
24
to alter the switch-on period.
OFF
Turn the button
to reduce the switch-on period (OFF) or
to extend the switch-on period (ON).
67
12
Program all the other switching times.
0
The day changes at 00:00 hours.
1234567
Confirm the setting.
0
12
12
24
24
OFF
OFF
ON
1234567
0
Select the switching time
Use
12
1234567
ON
Sunday 23:00
Monday 0:00 Uhr
Altering/deleting programs
EXIT
TIME
DATE
SU WIEXIT
PROGTIME
DATE
SU-WI
PROG
ON
and
.
to alter the switch-on period.
24
OFF
Turn the button
ON
to reduce the switch-on period (OFF) or
to extend the switch-on period (ON).
Confirm the setting.
Testing
Display the switching times from Monday to Sunday.
Each upward movement of the 5-way switch moves the display to the next switching state change. After the last switching state change in a
week, the display shows PROG END.
EXIT
TIME
DATE
SU WI
PROG
TIME
DATE
SU WI
PROG
TEST
0
1234567
0
12
12
24
24
OFF
ON
OFF
1234567
PROG
END
ON
NO
PROG
No program set
Reset
Permanent switching ON/OFF
Hardware Reset
EXIT
TIME
DATE
SUONWI
PROG
OFF
MODE
INFO
SU WI
PROG
TEST
AUTO
ON
EXIT
TIME
DATE
SU WI
PROG
ON = permanently switched ON
OFF = permanently switched OFF
00:00 Uhr
Date
01.01.2007
Summer time
EUROPA
Function
AUTO
Mode
V-AC (mains power)
OFF
ON
If a mains failure occurs, the display is blank.
The relay state is maintained.
When mains power is restored, the display reappears after 5 seconds.
Press the 5-way switch (> 1 sec) to activate the display. The time
clock can then be programmed.
When mains power is restored, the switching program will be
executed according to the programs previously set.
Changing the battery
Battery power
Mains power
EXIT
TIME
DATE
SU WI
PROG
TEST
AUTO
ON
OFF
MODE
2
1
Battery type: lithium cell CR2032
Manufacturer: Panasonic/Renata
High temperature type min + 70°C
In case of use other cells we don’t assume any liability.
= BATT
= V-AC
MODE
BATT
V-AC
In battery power mode BATT all the power is supplied
by the lithium cell. A mains power supply is not needed
in this case. The life of the lithium cell will be shorter in
battery power mode than in the factory setting of mains
power mode. Press the 5-way switch (> 1 sec) to operate. The switching programs will be executed and the
relay switches even without mains power. The sound of
the relay switching every hour is due to the refresh
(relay status is refreshed).
3
To avoid loss of
data, the battery
should be
replaced within
7 seconds.
OFF
Mains failure
Note: if a reset takes place in battery power mode, you must
re-select battery power mode under the MODE option.
Otherwise, the time clock will operate in mains failure mode and
the switching programs will not be executed.
The device must be disconnected from the mains power
supply before dismantling the
module.
Replace the module before
reconnecting mains power to
the device.
ON
OFF
For automatic operation, select AUTO.
The following switching programs are deleted
Time
PROG
TEST
AUTO
ON
OFF
ON
In mains power mode V-AC (factory setting) the display switches off if a mains power failure occurs. After
pressing the 5-way switch (> 1 sec) the time clock can
be programmed. The switching programs are not
executed in mains failure mode.
When mains power is restored, the relay will switch
again according to the programs previously set.
The sound of the relay switching every minute is due to
the refresh (relay status is refreshed).
4
5
Note: After fitting the module in BATT operating mode, it may take up to 1 hour
for the switching output to apply the module set state.