Samsung SCP-3370TH User manual

SPEED DOME CAMERA
User Manual
SCP-2370/SCP-2370H/SCP-2370TH/
SCP-2330/ SCP-2330H/
SCP-2270/SCP-2270H/
SCP-3370/ SCP-3370H/SCP-3370TH
SPEED DOME CAMERA
User Manual
Copyright
©2011 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the
user’s own responsibility. Samsung Techwin shall have the right to change the contents of this manual without
prior notice for the purpose of enhanced performance.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that there are important operating and maintenance instructions in the
literature accompanying this unit.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
- REPLACE WITH SAME TYPE 250V T3.15AL FUSE(F1)
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or
damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water
on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause
fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product
in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
CAUTION - Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to
excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -50°C), or high
humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire
or damage to the product.
English - 3
● SAFETY INFORMATION
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within
this unit.
safety information
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
9. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CCD.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian Interference.-Causing
Equipment Regulations of ICES-003.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at
the end of their working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human
health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of
waste and recycle them through your local, free battery return system.
4_ safety information
important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including
amplifiers) that produce heat.
8. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus
WARNING
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the
installation instructions.
English - 5
● IMPORTANT SAFETY INSTRUCTIONS
5. Clean only with dry cloth.
CAUTION
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric
shock, do not perform any servicing other than that contained in the operating instructions unless you are
qualified to do so.
DETAILED WARNINGS AND CAUTIONS
y Avoid operating the camera for long durations under high temperatures and in high humidity. Excessive
heat can shorten the lifespan of the camera components.
y Do not install or place the camera near any heat sources.
y Subjecting the dome cover to physical shock may damage the camera and cause water leakage into it.
y Do not place the camera facing direct sunlight or other intense light sources. Strong lights such as
spotlights can cause distortions—blooming and smear—as well as discolorations on the screen by
heating up the color filter of the camera. They also may cause internal reflections of the camera, leading
to operational malfunctions.
y Do not drop the camera or subject it to physical shock or vibration; this can cause serious damage to the camera.
y When installing the camera near a power line, make sure to keep at least 1 meter distance from the
power line, or earth an additional metal pipe to separate the camera from the power source.
y Install this camera on the ceiling. Installing it on the ground or a unleveled location may cause product
malfunctions and shorten its lifespan.
y Avoid installing and operating the camera in the following places.
- Places whose temperature exceed the camera’s recommended range.
(Indoor : -10º ~ 50º, Environmental : -50º ~ 50º)
- Places where drastic temperature changes occur: e.g. Near an air conditioner.
- Places that are exposed to steam, oil, and inflammable substances: e.g. Inside a kitchen.
- Places that are exposed to radioactivity, X-rays, strong electric waves, and electro-magnetic waves.
- Places that are exposed to outdoor air contaminants: e.g. Dust and car exhaust.
- Places in high humidity.
- Places that are exposed to corrosive gas: e.g. Next to the sea.
y Smeared and dusty dome covers decrease the picture and video quality. Clean the dome cover and
camera lens on a regular basis.
y Remove the plastic wrap on the dome cover only after the camera installation is complete.
y This camera is not equipped with a power switch. Plug in the camera only after the installation is
complete.
CAUTIONS FOR OPERATING TEMPERATURE (FOR ENVIRONMENTAL MODELS)
1. The camera cannot operate properly at temperatures lower than -50°.
2. Even if the surrounding temperature is -50° or higher, the camera may not thaw itself and operate
properly depending on the installation environment.
3. Always keep the power on, so the camera can maintain its internal temperature at -10° or higher.
4. If the product is kept at a low temperature, it may take a max of 2 hours to warm up for normal
operation.
6_ important safety instructions
6. The speed of the horizontal/vertical rotation will be deteriorated than normal at below -10 degrees for
the indoor model, and at below -40 degrees for the environmental model.
7. If the heater malfunctions, a message appears as follows.
- "Please Check Heater System"
- If this message appears, turn off the camera and call where you bought.
DETAILED WARNINGS AND CAUTIONS (SCP-2370TH/SCP-3370TH)
The following cautions are for the Auto Track function built-in with the SCP-2370TH/SCP-3370TH;
To use Auto Track to its full potential, please read and be aware of the following cautions. Neglecting the
cautions may cause unsatisfactory performance of the tracking function as well as camera malfunctions.
y Auto Track is specifically to track down unknown intruders. It is not be suitable to monitor a crowd.
y If the camera is not safely secured, tracking errors may occur.
y If the camera lens is smeared with foreign substances, snow flakes, or raindrops, the camera may incur
unsatisfactory performance in the tracking function. For optimal performance, please install the camera in
an environment safe from contamination, and clean the camera lens on regular basis.
y It may not operate properly in a low contrast condition at night.
y If the tracking function shows poor performance at nighttime or under low light circumstances, use the
Sens-Up function.
y Auto Track may have errors at times when pronounced shadows are created: e.g. sunrise and sunset.
y The camera may catch and follow unintended movements – car traffic or swaying tree branches – during
the Auto Track operation. To prevent and correct such errors, adjust the installation direction and angle
of the camera, or use Zone Settings (Mask) (page 71).
y Adjust the installation direction and angle of the camera, or use Zone Settings also under the following conditions:
With excessively bright light sources, under flickering lights, or if the camera displays internal reflections.
y When using Auto Track, it is recommended to adjust the tracking object size to 1/4 of the screen.
y This feature may not perform as expected depending on the situation and circumstances. Samsung
Techwin is not responsible for injuries and financial damage caused by the situation described above.
Samsung Techwin cares for the environment at all product manufacturing stages to
preserve the environment, and is taking a number of steps to provide customers with
more environment-friendly products.The Eco mark represents Samsung Techwin’s
will to create environment-friendly products, and indicates that the product satisfies
the EU RoHS Directive.
English - 7
● IMPORTANT SAFETY INSTRUCTIONS
5. If the camera was turned on after being left at temperatures lower than -50° for a long duration:
- If the internal temperature is lower than -20°, the camera does not transmit video signals and
displays a black screen along with the "Wait to warm up(xx Left)" message, instead of operating
properly.
- If the internal temperature is higher than -20° and lower than -10°, the "Wait to warm up(xx Left)"
message disappears as the camera resets itself and enters the operation mode.
However, only manual P/T operation is in effect while the Sequence and Turbo commands are
limited in use.
- If the internal temperature is higher than -10°, the camera activates all Sequence and Turbo commands.
setting up auto track
Two different Auto Track setup methods are available.
y Using Presets
- Select a starting point for Auto Track as a preset to activate Auto Tracking. (This can be used in
conjunction with Group SEQ and Tour SEQ.)
y Using Target Lock
- Select an object on the screen to activate Auto Tracking.
M  The PIP feature will be disabled if using Auto Track.
AUTO TRACK USING PRESETS
Preset
Settings
· Set a Preset to Start
Auto Tracking
· Set Zoom/Focus
Auto
Tracking
Editing
Presets
· Select Tracking Mode
for a Preset
· Tracking On
· Set Auto Tracking
details
<Auto Track Setting Flow Chart>
1. Selecting Auto Track Starting Point 1
z Using the joystick, select a preset number from 1 to 255,
and then press [Enter].
Preset Setting
Preset = 001 (255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
Preset Setting
1+PST:ZOOM 2+PST:FOCUS
8_ setting up auto track
2. Selecting Auto Track Starting Point 2
z At Preset Edit, select the preset number under the Preset
Settings menu.
- The selected preset is indicated with an asterisk (*).
- Auto Track : Perform Auto Track upon arrival.
Ú For a SCP-3370 series model, select [AutoTrack] from
[Intelligence], not from [After Action].
Preset = 001* (255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
Preset Edit
[001]
PTZ
Focus
Brightness
Iris
Back Light
Day/Night
After Action
Scene Adj
XXX/XXX/XXX
ONE SHOT
050
AUTO
OFF
AUTO
OFF
Preset Edit
z When the [After Action] menu is set to [Auto Track], the
letter “T” appears next to the preset number as shown in
the figure.
3. Setting Auto Tracking Details
z Select [Main Menu – P/T Setting – Auto Track].
z At Menu [Auto Track], select [ON] to activate Auto Tracking.
z Set the Camera Height, Object Size, Sensitivity, and Zoom
Control options.
z Refer to the operation timing chart in the next page and set as
necessary each of: [Auto Release], [Auto Return] and [Lost Mode].
Preset = 001T (1~255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
Auto Tracking
Auto Track
Camera Height
Object Size
Sensitivity
Zoom Control
Auto Release
Auto Return
Lost Mode
Others
OFF
2.5M
SMALL
HIGH
OFF
OFF
OFF
STOP
English - 9
● SETTING UP AUTO TRACK
z At Menu [After Action], select [Auto Track].
Preset Edit
setting up auto track
[ Auto Release ]
(10sec ~ 5min)
Start
Tracking
[ Lost Mode ]
Performed only for the
Auto Release duration
[ Auto Return ]
(1sec ~ 5min)
Finish
Tracking
Initial
Location
<Auto Track Timing Chart>
z Auto Release: Command the camera to follow an object for a set duration and then return to
its initial (preset) location.
z Auto Return : After Auto Release expires, command the camera to stand by at the tracking
finish point and then return to its initial location. (Selecting OFF keeps the
camera at the tracking finish point instead of returning it to the initial location.)
z Lost Mode : Set an action for the camera when it loses its tracking object. (Performed only for
the Auto Release duration.)
- STOP : Stop at the lost point and abort tracking.
- RESEARCH : Stop at the lost point and search for a new object.
- ZOOM-OUT : When an object is lost, Zoom Out to find and track a new object.
4. Starting Auto Track (Loading Presets)
z Start Auto Tracking in the OSD Menu
1. Select [Execute].
2. Select a Preset to start Auto Tracking.
3. The camera will move to the Preset location and start Auto
Tracking.
z Start Auto Tracking Using the Controller
1. Exit the OSD menu then press a Preset number on the
controller keypad to start Auto Tracking. And Press a
<Preset> button.(The number can be checked on the LCD
window.)
2. The camera will move to the Preset location and start Auto
Tracking.
10_ setting up auto track
Preset
Setting
Edit
Home Position
Execute
Clear
Status
OFF
Preset Edit
Preset = 001T (1~255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
5. Auto Tracking Using Group Command
z PSET : Using the joystick, enter a preset number under
which [After Act.] menu is set to [TRACK].
Group SEQ 1
location. (1 ~ 120sec)
z SPD : Adjusts the camera movement speed by 64 different
levels.
[Preset 1]
[Preset 2]
PSET
*** :
*** :
*** :
*** :
*** :
*** :
*** :
Start
Tracking
[ Lost Mode ]
Performed only for the Auto
Release Duration
SPD
64
64
64
64
64
64
64
[Preset N]
[Auto Release]
(10sec~5min)
Start
Group SEQ
DWT(s)
003 :
003 :
003 :
003 :
003 :
003 :
003 :
Last
Preset
Finish
Tracking
[ Auto Return ]
(1sec~5min)
Next
Preset
<Group SEQ Timing Chart>
z When Group SEQ is activated, the camera starts auto tracking at the [Preset 1] location. For
the set DWT duration, the camera performs Auto Track according to [Auto Release] and [Auto
Return] settings. If no movement is detected, it moves to [Preset 2] and repeats the procedures.
AUTO TRACKING USING TARGET LOCK
1. Setting Target Lock
z Target Lock => [ON]
- When Target Lock is turned [ON], a red box appears in the
center of the screen.
Others
Zone Setting
Indicator
Target Lock
OFF
OFF
2. Target Lock
z Using the joystick, move the red box to encircle an object and
then press [Enter] to start Auto Tracking the object.
P:234 T:5 1x
English - 11
● SETTING UP AUTO TRACK
NO
001:
002:
003:
004:
005:
006:
007:
z DWT : Indicates the camera time spent at each preset
contents
INTRODUCTION
13
CONNECTION & INSTALLATION
18
SETUP
44
TROUBLESHOOTING
13
15
16
17
Features
What’s included
Component Names and Functions (Indoor Model)
Component Names and Functions
18
19
21
22
25
33
34
35
36
39
42
Camera Wiring Interface Board
Camera and Appliances Wiring Diagram
How to Set Up Protocols and ID DIP Switches
Communication Protocol DIP Switch
Settings (SW2)
Camera ID DIP Switch Settings (SW1)
Preparing Adapter and Cables
Product Configurations
Preparing & Installing Camera Bracket
Optional Accessories for Installation
On-Ceiling Mount Type Installation Example
Example of installing an Environmental model
44
45
46
47
57
69
79
80
83
84
84
Interface Symbols
Using and setting the menus
OSD Menu Chart
Camera Setup
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password setting
Status
85 Troubleshooting
85
PRODUCT SPECIFICATIONS
89
12_ contents
89 Product Specifications (SCP-2XXX Series)
91 Product Specifications (SCP-3370 Series)
93 Dimensions
introduction
FEATURES
y A/F 37x/33x/27x Optical Zoom
The built-in 37x / 33x / 27x optical zoom lens with auto-focus is combined with a 16x digital
zoom, providing a maximum of 592/528/432 zoom.
y Wide Range Auto Security Functions
- Auto Tracking (SCP-2370TH/SCP3370TH Only) : A moving object or a person can be tracked and recorded
automatically by the camera with its Pan, Tilt, and Zoom functions.
- Multiple Preset Function Saving : Up to 12 camera image properities can be saved individually to provide
high quality pictures.
- Image Holding : When moving between presets in Group and Tour functions, using this Preset Freeze function holds the image status and helps the screen observer relieve visual fatigue.
- PTZ Trace : Patterns operated with the joystick can be saved and replayed by users.
- Swing : Using the Swing function commands the camera to move between 2 selected locations, monitoring
the route.
- Group Search : Maximum 128 Preset positions are toured in order.
- Tour Search : Maximum 6 Group Search functions are toured in order.
y Digital Flip
The Digital Flip function is useful to monitor moving objects or people passing directly under the
camera. When an object or a person passes directly under the camera, its tilt motor follows the
object or person over 100 degrees to the other side of the tilt area without panning. The screen
inversion starts to occur at 100 degrees or higher is digitally adjusted.
y Smart P/T
The Smart P/T function automatically adjusts the control speed of the Pan and Tilt functions
according to the current zoom ratio. It is useful to adjust the functions manually for detailed controls
when monitoring at high zoom ratios.
y Day & Night
With its daytime & nighttime switch and Sens-Up functions based on the ICR (Infrared Cut filter
Removal) method, the camera provides high quality pictures regardless of whether it is day or night.
- Sens-Up increases the CCD sensitivity by electrically extending the camera’s exposure time.
- Day & Night enables you to select between color and B/W modes depending on the lighting conditions.
y Highly durable built-in housing
This IP66-rated built-in housing is easy to install, and protects the product from a full range of harsh
outside conditions. The high performance built-in fan/heater enables the product to operate under
extreme temperatures between -50° ~ 50° .
English - 13
● INTRODUCTION
y Versatile protocols and coaxial communication
RS-422/485, Coaxial communication methods are supported.
- RS-422/485 (10 species) : Auto Detected, SAMSUNG-T, SAMSUNG-E, Pelco (D/P), Panasonic, Vicon,
Honeywell, AD, GE, BOSCH
- Coaxial Communications : Pelco Coaxitron (automatic detection)
introduction
y Preset Position Saving and Loading
Up to 255 preset positions can be set. Using this function saves and brings up the camera feed of
a selected monitoring location.
y Camera Backup
This is to back up the camera’s sequence information and presets. This is useful when the camera
or its install base are damaged or malfunctions occur.
y Area Masking
If a monitoring location includes a highly private area, the area can be selectively masked on the
screen.
y Model Specifications
SCP-XXXXTH
Environmental Model
Auto Tracking Model
Zoom Factor
37: 37 Zoom Lens / 33: 33 Zoom Lens / 27: 27 Zoom Lens
DSP Chip
2: W-V DSP/3:SV-V DSP
14_ introduction
WHAT’S INCLUDED
Check if the following items are included in the product package.
Appearance
Item Name
Description
Applicable
Model
1
-
Indoor Model
1
-
Environmental
Model
1
Multilingual User Manual
Main Body
CD Manual
All
User Manual
1
English User Manual
Fixing Screw
3
If mounting the install base on the
ceiling
Installation Template
1
If determining the installation
point before mounting the install
base on the ceiling
Installation base
1
If installing it indoors or in a ceiling
housing
Hexagon screw
3
Used for attaching the installation
base to the camera
Indoor Model
Environmental
Model
L Wrench
1
Used for fixing the installation
base after attaching it to the
camera
Ú For classification of the indoor and environmental models, refer to page 14.
English - 15
● INTRODUCTION
Quantity
introduction
COMPONENT NAMES AND FUNCTIONS (INDOOR MODEL)
Front
Back
➊
Bottom
➋
❶ Unlock Button
❷ SW2: Communication DIP Switch
❸ SW1: ID DIP Switch
➍ Safety Cable Hook
➌
➍
16_ introduction
COMPONENT NAMES AND FUNCTIONS
Front
Back
Bottom
➋
➌
➊ Safety Wire Holder
➋ SW2: Communication DIP Switch
➌ SW1: ID DIP Switch
Ú For the DIP switch settings, please refer to the
“Installing Your Camera” on Page 21~25.
English - 17
● INTRODUCTION
➊
connection & installation
CAMERA WIRING INTERFACE BOARD
For the camera wiring, please refer to the picture below.
(When using coaxial communication, a separate control signal connection is not required.)
Alarm
2.NC
2.NO
2.COM
7*%&0
IN5
Alarm Input
5~8
%
+
IN6
*/
GND
(/%
IN7
Alarm Output 2
2.NC
*/
2.NO
2.COM
*/
*/
Alarm Output 1
1.NC
1.NO
1.COM
IN8
GND
IN4
IN3
IN4
Alarm Input
1~4
39 39 59 59 (/%" $0."/0
Communications and AUX
39
39
Power Supply
'(
AC24V 2.5A
Power Input
Refer to the below Control
Signal Connection chart
Ground
AUX Output
Control Signal Connection
• RS485 Communications
Camera
RX+
RX-
Controller
or DVR
TXD+
TXD-
• RS422 Communications
Camera
RX+
RXTX+
TX-
Controller
or DVR
TXD+
TXDRXD+
RXD-
M  The maximum power capacity of the built-in relay is 30VDC/2A, 125VAC/0.5A, and 250VAC/0.25A.
 Connecting the power connector and GND incorrectly to the NC/NO and COM ports may cause a short circuit and fire,
damaging the camera.
18_ connection & installation
CAMERA AND APPLIANCES WIRING DIAGRAM
Connecting with Samsung Techwin’s “Stand Alone DVR”
Camera
RX+
RX-
● CONNECTION & INSTALLATION
y RS-485 :
Stand Alone DVR
T(TXD)+
T(TXD)-
y RS-422 :
Camera
Stand Alone DVR
RX+
RX-
T(TXD)+
T(TXD)-
TX+
TX-
R(RXD)+
R(TXD)-
Connecting with the Samsung Techwin Controller SPC-6000
y RS-485 :
Camera
RX+
RX-
TXD+
TXD-
TX
RX
+ -
TX
G
+ -
+ -
RX
+
-
y RS-422 :
TX
+ -
Camera
RX
+ -
G
TX
+ -
RX
+
-
MENU
SEARC
H
MULTI
REC
MENU
PRESE
T
CAM
MON
GROUP
PTZ
DVR
1
TX+
TX-
RXD+
RXD-
RX+
RX-
TXD+
TXD-
TRACK
MTX
2
3
6
SETUP
4
7
FUNC
5
8
ESC
9
ENTER
CLOSE
OPEN
0
NEAR
FAR
WIDE
TELE
<Controller>
English - 19
connection & installation
To connect to Samsung PC DVR
y RS-485 :
Camera
PC DVR
RX+
RX-
SRP-1610/1650
20_ connection & installation
HOW TO SET UP PROTOCOLS AND ID DIP SWITCHES
You can control various settings of the camera system using the Communication and ID DIP switches.
Before installing the product, please set up the DIP switches according to the installation environment.
Communication Protocol DIP Switch(SW2)
Camera ID DIP Switch(SW1)
English - 21
● CONNECTION & INSTALLATION
1. Detach the camera frame from the install base, and place the bottom of the frame toward you as shown in the
picture below.
2. Set the switches according to your installation environment. For more detailed setup information, please refer
to the chart on the next page.
3. The camera may malfunction if the switches are not fully turned On/Off; please double check the switches
before finishing setup.
connection & installation
COMMUNICATION PROTOCOL DIP SWITCH SETTINGS (SW2)
Coaxial communication automatically detects signals, and so does not require a separate communication
setup process.
ON
ON
OFF
SW2
SW2 Pin No.
Purpose
1~4
Protocol Settings
5~6
Baud Rate Settings
7
Transfer Method (RS-485/422) Settings
8
Response Mode Settings
9~10
Backup Mode Settings
11~12
Termination Settings
Protocol Settings
Select a communication protocol for the camera.
No
Protocol
SW2-#1
SW2-#2
SW2-#3
SW2-#4
1
Auto Detected
OFF
OFF
OFF
OFF
2
Samsung-T
OFF
OFF
OFF
ON
3
Samsung-E
OFF
OFF
ON
OFF
4
Pelco-D
OFF
OFF
ON
ON
5
Pelco-P
OFF
ON
OFF
OFF
6
Panasonic
OFF
ON
OFF
ON
7
Vicon
OFF
ON
ON
OFF
8
Honeywell
OFF
ON
ON
ON
9
AD
ON
OFF
OFF
OFF
10
GE
ON
OFF
OFF
ON
11
Bosch
ON
OFF
ON
ON
22_ connection & installation
Baud Rate Settings
Select the transfer speed of a selected communication protocol.
Baud Rate (BPS)
SW2-#5
SW2-#6
1
2,400
ON
ON
2
4,800
ON
OFF
3
9,600
OFF
OFF
4
19,200
OFF
ON
Communication Method Settings
Select a communication method for the camera.
SW2- #7
Function
Transfer Mode Switch
ON
RS-422 (4Wire)
OFF
RS-485 (2Wire)
Communication Response Settings
Select a communication response method for the camera and controller: Response or No Response.
SW2- #8
Function
ON
OFF
Response Mode Switch
Response
No Response
Termination Settings
To prevent the attenuation of communication signals between the camera and controller, the items at
the end of line must be set up with the termination settings.
Camera Input Position
SW2- #11
SW2- #12
Termination of Longest Path (RS-422)
ON
ON
Termination of Longest Path (RS-485)
ON
OFF
On the Path
OFF
OFF
y Example of terminal setting
Ú If using RS-422, SW2-#11: ON /SW2-#12: ON for camera 16
Ú If using RS-485, SW2-#11: ON / SW2-#12: OFF for camera 16
English - 23
● CONNECTION & INSTALLATION
No
connection & installation
Camera Backup Settings
These settings are useful when the camera or its install base are damaged or malfunctions occur.
When replacing the camera or its install base, you can transfer existing presets and sequence
information to the replacement using these settings.
Backup Function
SW2- #9
SW2- #10
Backup(IBˆD)
OFF
OFF
Backup(DˆIB)
ON
OFF
Backup Disable
-
ON
- Backup(IBˆD) : Enables transferring the current camera's sequence information to a new camera.
- Backup(DˆIB) : Enables transferring the current camera's sequence information to a new install base.
Ú IB: Install base, D: Dome Camera
■ [Current Time] is not backed up from install base to camera.
this model, all DIP switches are set to OFF by factory default. Each of the default settings will be grayed out in the
I  Forapplicable
menu.
 To use a third party controller with this product, please contact our After-Sales Service or Technology Department.
 AD Protocol Control Method
1. Input Camera OSD: 3+Auxiliary On
2. Output Camera OSD: 3+Auxiliary Off
3. Enter: IRIS Open
4. ESC: IRIS Close
 For more information about the protocols, refer to our official website.
24_ connection & installation
CAMERA ID DIP SWITCH SETTINGS (SW1)
Assign a unique number for each camera to identify itself from others.
ON
ON
● CONNECTION & INSTALLATION
OFF
SW1
1. The initial value of the switch is “0”, and all of the 8 switches are
defaulted to OFF.
ON
OFF
2. Each switch has a unique value, and the board ID is the sum of
the values of the switches.
 Refer to the example below for the board ID.
Example 1
Example 2
1+2 = 3 (Board ID = 3)
Example 3
4+32 = 36 (Board ID = 36)
1+2+4+8+16+32+64+128
= 255 (Board ID = 255 )
M  Use a unique ID for each Camera.
English - 25
connection & installation
y Camera ID Chart
ID
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
SW1-#1
ON/OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
SW1-#7
SW1-#8
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
26_ connection & installation
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
SW1-#7
SW1-#8
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
English - 27
● CONNECTION & INSTALLATION
ID
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
connection & installation
ID
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
28_ connection & installation
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ID
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
SW1-#7
SW1-#8
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
English - 29
● CONNECTION & INSTALLATION
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
connection & installation
ID
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
SW1-#7
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
30_ connection & installation
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ID
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
English - 31
● CONNECTION & INSTALLATION
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
connection & installation
ID
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
32_ connection & installation
SW1-#6
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
PREPARING ADAPTER AND CABLES
y Power Adapter
Power adapter has the capacity of AC24V 2.5A.
Distance
Recommended Cable
Specification
300m
4C2V(RG-59/U)
450m
5C2V(RG-6/U)
600m
7C2V(RG-11/U)
the camera is controlled through coaxial communication, please use a video amp intended for coaxial communications.
M  IfRegular
video amps do not transfer coaxial signals.
y Communications Cable
For the camera to communicate with the controller, a
RS-485/422 communications line is required. To ensure the
quality of long distance communication and the accuracy of the
overall communication it is recommended using a twisted pair
cable such as UTP.
M  Depending on the camera’s environment, the communications distance may vary.
 Neither the video nor communications cable is enclosed with the camera.
English - 33
● CONNECTION & INSTALLATION
y Video Cable
The camera’s video output port is connected to the monitor with a BNC coaxial cable, shown below :
If the distance between the camera and the monitor exceeds the recommended maximum, please use
an auxiliary video amp.
connection & installation
PRODUCT CONFIGURATIONS
ALARM
HDD
NETWORK
BACKUP
REC
REC
1
2
5
DVD RECORDER
3
6
7
4
8
9
10
11
12
13
14
15
16
ZOOM
FR
TELE
WIDE
MODE
AUDI
VIEW
PRESET
USB
OPEN/CLOSE
RETURN
RS-485
SRD Series
1
2
16
....
ALARM
HDD
NETWORK
BACKUP
REC
REC
1
2
5
DVD RECORDER
3
6
7
4
8
9
10
11
12
13
14
15
16
ZOOM
FREEZE
BACKUP
TELE
WIDE
VIEW
MODE
AUDIO
ALRAM
SEARCH
MENU
USB
OPEN/CLOSE
RETURN
RS-485
SRD Series
1
....
2
16
ALARM
HDD
NETWORK
BACKUP
REC
REC
1
2
5
DVD RECORDER
3
6
7
4
8
9
10
11
12
13
14
15
16
ZOOM
FREEZE
BACKUP
TELE
WIDE
VIEW
MODE
AUDIO
ALRAM
SEARCH
P
MENU
USB
OPEN/CLOSE
R
Coaxial Communication
SRD Series
1
....
2
16
ALARM
HDD
NETWORK
BACKUP
REC
REC
1
2
5
DVD RECORDER
3
6
7
4
8
9
10
11
12
13
14
15
16
ZOOM
FREEZE
BACKUP
TELE
WIDE
VIEW
MODE
AUDIO
ALRAM
SEARCH
MENU
USB
OPEN/CLOSE
RETURN
Coaxial Communication
SRD Series
1
2
16
....
CONTROLLER (MAIN)
CONTROLLER (SUB)
MENU
SEARC
MENU
SEARC
H
MULTI
H
MULTI
REC
REC
MENU
MENU
PRESE
T
PRESE
T
CAM
CAM
MON
MON
GROUP
GROUP
PTZ
PTZ
DVR
1
3
SETUP
4
7
ESC
9
DVR
3
SETUP
4
7
ENTER
OPEN
FUNC
5
8
CLOSE
0
TRACK
MTX
2
6
FUNC
5
8
1
TRACK
MTX
2
6
ESC
9
ENTER
CLOSE
OPEN
0
NEAR
NEAR
FAR
FAR
WIDE
WIDE
TELE
34_ connection & installation
TELE
CONTROL LINE
VIDEO LINE
CONTROL/VIDEO LINE
PREPARING & INSTALLING CAMERA BRACKET
For installation guidelines for brackets and housings, refer to the installation manual that is enclosed with the
bracket or housing.
❖ Available Bracket Models
Item
SHP-3700H
Outdoor Housing
SBP-300HM1
Hanging Mount
Indoor Model
Environmental Model
-
SBP-300WM1
Wall Mount
SBP-300WM
Yes
SBP-300CM
Ceiling Mount
SBP-300LM
Parapet Mount
SBP-300KM
Corner Mount
SBP-300PM
Pole Mount
Yes
M  See “Optional Accessories for Installation” for the appearance of each bracket
English - 35
● CONNECTION & INSTALLATION
Model
connection & installation
OPTIONAL ACCESSORIES FOR INSTALLATION
For your easier installation, you can purchase appropriate optional accessories available.
1. If installing the camera on the wall
y Wall mount (SBP-300WM1)
y Wall mount (SBP-300WM)
2. If installing the camera on the ceiling
y Ceiling Mount (SBP-300CM)
3. If installing the wall mount (SBP-300WM/SBP-300WM1) on an at least
80mm-long cylinder
y Pole Mount (SBP-300PM)
36_ connection & installation
4. If installing the wall mount (SBP-300WM/SBP-300WM1) on a corner of the wall
y Corner Mount (SBP-300KM)
● CONNECTION & INSTALLATION
5. If installing on a building rooftop
y Parapet Mount (SBP-300LM)
6. If installing an indoor model outdoors
y Outdoor Housing (SHP-3700H)
7. If installing an indoor model on the ceiling
y Flush-Mount Indoor Housing for PTZ Dome Camera
(SHP-3700F/STH-370PE)
8. If installing an indoor model on the wall mount or ceiling mount
y Hanging Mount (SBP-300HM1)
English - 37
connection & installation
y Bracket Mounting (Indoor Model)
Wall mount (SBP-300WM1)
Wall mount (SBP-300WM)
Ceiling Mount (SBP-300CM)
Parapet Mount (SBP-300LM)
y Bracket Mounting (Environmental Model)
Wall mount (SBP-300WM1)
Ceiling Mount (SBP-300CM)
38_ connection & installation
Wall mount (SBP-300WM)
Parapet Mount (SBP-300LM)
ON-CEILING MOUNT TYPE INSTALLATION EXAMPLE
Template
Lever
y Wiring Terminal Cables
Connect the cables to the terminal block on the hinged door. For the
location of the wiring pins, please refer to the “Camera Wiring Diagram”
on Page 18. Once the wiring is successful, close the hinged door.
connect the camera to a power outlet until the installation is complete. Supplying power in the middle of the installation
M  Domaynotcause
fire or damage the product.
English - 39
● CONNECTION & INSTALLATION
y Attaching the template and installing the install base
Attach the provided template on the ceiling. Based on the template, drill a 88mm hole in the ceiling and
arrange the wires through the hole. Then, install the install base as shown.
Before installing the exposed bracket, open the hinged door at the bottom of the bracket as shown in the
picture. Hold the Lever on the hinged door to open.
connection & installation
y Setting Up Camera DIP Switches
DIP switches for communication and ID protocols are located on the bottom of the camera.
For the switch settings, refer to the dip switch settings of this manual.
Protocol (SW2)
ID (SW1)
y Connecting Camera Safety Cable and Attaching Camera
Carefully attach the camera to the mount following the alignment guide marks as shown in the picture.
First hook the camera's safety cable on the mount, and then attach the camera.
Safety
Cable
Alignment
Direction
Guides
Alignment
Direction
Guides
Alignment
Directions
✽ To attach the camera to the mount, refer to the alignment guide marks as shown in the picture.
sure to first hook the camera's safety cable to the mount before proceeding. Otherwise you may be exposed to serious
M  Make
injury caused by a fallen camera.
40_ connection & installation
✽ To attach or detach the camera, refer to the picture.
* Attaching the camera: Hold up the camera and push it to the mount as shown in the picture. Push the
camera until you hear a “click”.
* Detaching the camera: To detach the camera, pull the camera downward while pushing the unlock buttons
on the camera upward.
● CONNECTION & INSTALLATION
Unlock Button
UNLOCK
To attach the
camera
To detach the
camera
English - 41
connection & installation
EXAMPLE OF INSTALLING AN ENVIRONMENTAL MODEL
❖ Fix the installation base with the bracket
1. Fix the base with the bracket by turning it clockwise.
2. As shown in the picture below, gently press and lift up the handle
of the hinged door on the bottom of the installation base. Please
refer to the “Camera Wiring Interface Board” on page 18, connect
the wires.
Knob
not connect the camera to a power outlet until the installation is complete.
J  DoSupplying
power while the installation is in progress may cause fire or damage
the product.
3. Connect the camera safety wire to the installation
base.
Safety Cable
42_ connection & installation
4. Assemble Camera and Installation Base
Assemble the installation base and camera by
matching the installation direction guides.
● CONNECTION & INSTALLATION
5. Attach Camera
Turn the camera frame counterclockwise until the
protrusions on the camera frame and installation
base become matched perfectly.
6. Secure Camera and Installation Base
As shown in the picture below, secure the
installation base and camera using 3 hexagon
screws.
English - 43
setup
INTERFACE SYMBOLS
y Motion Detection Standby/Operation Display :
When in standby mode, the “
if motion is detected.
” in the upper right of the screen blinks and then changes to “
”
y Alarm Input Port Status Display :
"①", "②", "③", "④", "⑤", "⑥", "⑦", and "⑧" in the upper right of the screen blink.
y Current Alarm Port Display According to Input Alarm Ports(Priority) :
Only one of " ➊", " ➋", " ➌", " ➍", " ➎", " ➏", " ➐", " ➑" in the upper right of the screen blinks.
Ú The alarm port indicator blinks only when the sequence is set .
y Preset Number Display Settings :
‘*’ : If a preset number is already available
'H' : If a preset location is the camera’s home position
'T' : If a preset location is the camera’s Auto Track starting point (SCP-XXXXT Only)
y PTZ Function Screen :
Camera Name
Motion Detect
Alarm Input
Area Display
Sequence Status
Preset Info
ID=001
Area1 Area Name
G-SEQ1
PRESET : 001 Preset Name
P:300 T:040 010X
y Preset Number Setting Screen :
Preset Setting
Preset=011* (1~255)
44_ setup
1234
5678
USING AND SETTING THE MENUS
OSD (On-screen Display) Indicators
Has no submenu
● SETUP
Has submenu
Camera Setting
偓Zoom/Focus
White Balance
-----------
ATW
Operating Your Camera
z Panning and Tilting :
Use the joystick of the controller or its direction buttons.
z Controlling Zoom :
Move the joystick clockwise (Tele) or counterclockwise (Wide), or use the zoom buttons.
z Accessing Screen Menus:
Press the Menu or OSD button on the controller.
more detailed information about controls using a third party controller or a DVR, refer to the user’s manual of the
M  Forproduct.
OSD Commands, Function Chart, and Menu Controls (Applied to Samsung
T/Samsung E protocol)
This camera can be operated using two methods: Using hot keys on its dedicated controller, or
accessing the OSD (On Screen Display) on the video output.
The OSD menu commands are as follows:
Command
Function
Move the joystick up/down/left/right
Moves the OSD menus up/down/left/right, respectively.
Enter/Focus Far
Selects a menu and allows access to the sub menus.
ESC/Focus Near
Cancels a command and moves back to an upper-level menu.
English - 45
setup
OSD Menu Chart
You can have an overall view of the menu structure. For more information, refer to the applicable page or
section in the manual.
Zoom/Focus
White Balance
Exposure
Back Light
Camera Setting
AGC
SSNR
SSDR
Day & Night
Others
Preset
Swing SEQ
Group SEQ
Sequence Setting
Tour SEQ
PTZ Trace
Auto Run
Pan/Tilt Limit
Power On Resume
Area Setting
Area Masking
Prop.P/T
P/T Setting
Digital Flip
Image Hold
Auto Tracking (SCP-XXXXT)
Jog Speed
Max Speed Level
Camera ID
Camera Name
Preset Number
Preset Name
OSD Setting
Seq. Status
Area Name
PTZ Position
Language
Others
Alarm Enable
Alarm Setting
Alarm Input
Alarm Output
MD Dwell Time
ALM Dwell Time
Power On Reset
Factory Default Set
Camera Default Set
Initialize
Auto Refresh
Auto Track Default (SCP-XXXXT)
Fan Life (Environmental Model)
Password Setting
Status
46_ setup
On/Off
Edit Password
CAMERA SETUP
Zoom and Focus Settings
z Focus Mode
z Zoom Tracking
Through this menu you can set up the camera’s focus mode when
zooming.
- Mode
y Auto : Auto-focuses when zooming.
y Tracking : Focuses manually when zooming.
y Off : Disable the focus modes when zooming. (Full manual
mode)
- Speed
y Slow/Medium/Fast : Adjusts the zooming speed.
Model
Fast
Medium
Slow
37x (SCP-3370)
2.8 sec
4.0 sec
7.1 sec
37x (SCP-2370)
2.5 sec
3.1 sec
5.6 sec
33x (SCP-2330)
2.2 sec
2.5 sec
4.7 sec
27x (SCP-2270)
1.8 sec
2.3 sec
4.5 sec
z Digital Zoom
Enables the maximum digital zoom.
Setting the digital zoom to 16x provides a total zoom of 592x.
the optical zoom, the graphics quality of the digital zoom decreases
M  Unlike
as its zoom ratio increases.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
AUTO
OFF
High
Medium
Æ
 The auto-focus function may not operate normally under the following
conditions :
- When background illumination is low
● SETUP
- AUTO : Performs continuous auto-focus.
- MANUAL : Changes the camera mode to Manual Focus.
- ONE SHOT : Auto-focuses the camera once after the Pan,
Tilt, or Zoom function is used.
Zoom/Focus
Focus Mode
- While Slow-Shutter is in operation
Zoom Tracking
- If the zoom level is set too high
Digital Zoom
- When background illumination is too high
- If a long distance object and a close distance object appear together within a monitoring area
- If there is no contrast, e.g. the sky or a wall
- If the camera is facing a thin horizontal line
ONE SHOT
OFF
 Auto Focus focuses on an object in the center of the screen; objects around the screen edges may not be properly in focus.
English - 47
setup
White Balance
The White Balance menu adjusts the balance of the screen colors
under different lighting conditions.
z ATW : Adjusts the screen color automatically.
(Color Temperature:1800~10500°K)
z INDOOR : Adjusts the screen color to be optimal in an indoor
environment. (Color Temperature:4500~8500°K)
z OUTDOOR : Adjusts the screen color to be optimal in an outdoor
environment. (Color Temperature:1700~11000°K)
z AWC : To obtain the optimal condition for the current lighting, put
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
the focus of the camera to a white paper and press the
SET button. If the lighting environment is changed, you
should readjust the settings accordingly.
Æ
Camera Setting
z MANUAL : Enables customization the Red and Blue gains.
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
AUTO
OFF
High
Medium
M  White Balance may not work properly under the following conditions.
➊ When the color temperature of the environment surrounding the subject is out of the control range.(e.g. Clear sky or sunset)
➋ When the ambient illumination of the subject is dim.
➌ If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, White
Balance adjustments may not deliver consistent results.
48_ setup
Exposure
The Exposure settings are to control the camera’s exposure meter.
z Brightness : Adjusts the screen brightness.
z Iris
- AUTO : Automatically adjusts the exposure meter.
- MANUAL : Enables manual adjustment of the exposure meter.
(F1.6~Close: 18 levels)
z Shutter : Controls the camera’s electronic shutter.
- --- : The shutter speed is fixed at 1/60 for NTSC and 1/50 for
PAL. Operates when Iris is on the Auto Mode.
- ESC : Adjusts the shutter speed automatically according to
the screen brightness. Operates when Iris is on the
Manual Mode.
- A.FLK : Select this setting when you experience picture
flickering. Flickering can happen when artificial lighting
frequencies clash with camera frame rates.
- MANUAL : Enables manual adjustment of the shutter speed.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
(Over 50: Brighter, Under 50: Darker)
Main Menu
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
z Sens-Up
- AUTO : Automatically detects light levels and maintains a clear SSNR
SSDR
picture at night or under low-light conditions.
Day & Night
- Sens-Up Limit : Adjusts to the maximum-powered zoom per
frame.
Others
AUTO
OFF
High
Medium
Æ
Exposure
performance of the A.FLK mode, avoid using the mode in conjunction
M  Forwithoptimal
Backlight.
Brightness
Iris
Shutter
Sens-Up
050
AUTO
--AUTO
 While the Internal Sync mode is in effect, setting the shutter to ‘---’ and facing the

camera directly to a bright light source may cause poor camera performance.
Sens-Up is disabled when the shutter is in Manual or A. FLK mode.
English - 49
setup
Back Light
The Backlight function is dedicated to SV-V DSP (SCP-3XX0) or W-V
DSP (SCP-2XX0) chip, developed by Samsung Techwin, which,
unlike the old models, provides a sharp image of both object and
background against a severe counter-light condition.
z Back Light Mode
- OFF : Disables the Backlight mode.
- WDR : Activates the Wide Dynamic Range mode.
- HLC : Activates the High Light Compensation mode.
- BLC : Activates a user defined backlight compensation mode.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
AUTO
OFF
High
Medium
” WDR (SCP-3XX0 Only)
When there are both bright and dark areas at the same time, this
mode makes both areas distinctive.
WDR Setting
Limit
Level
Mode
Anti Rolling
WDR ON
LOW
50
ON
ON
WDR OFF
- Limit : Three WDR sensitivity levels are available in 3: Low, Medium , and High.
Note that the higher the sensitivity level, the lower the contrast in the light and dark areas becomes.
- Level : Adjusts the screen brightness in WDR mode.
50_ setup
- MODE : Select a mode that is suitable to the indoor or outdoor backlight condition.
- ANTI ROLLING : Reduces the difference of ambient colors to lessen the rolling that occurs under the
fluorescent lighting.
M  WDR is disabled if the shutter is in Manual mode.
 During WDR operation, noise, discoloration, spots, and whitish symptoms may occur depending on lighting conditions. If
● SETUP
they occur, stop using WDR.
” HLC Setting
The HLC settings selectively eliminates high lights in a limited
environment such as the entrance to an apartment parking lot or
gas station, and is useful to detect a small objects like car license
plates.
HLC Setting
Level
Mask Tone
LOW
50
HLC is disabled during the daytime. While monitoring nigh time
car traffic, if car headlights reflects too much bright light on the screen, the camera automatically
eliminates the headlamp lights and adjusts the color of the license plate accordingly.
HLC Masking Area
<HLC ON>
<HLC OFF>
- Level : Adjusts the HLC sensitivity level.
- Mask Tone : Adjusts the mask color on the high lighted area.
M  Even if HLC is on, car license plates may not be detectable depending on the location and angle of the camera as well as
the lighting condition.
 For SCP-2xxx series, the HLC function will be disabled while using Digital Zoom, Freeze or Stabilizer. (However, SCP-3370
can enable HLC with any of these functions.)
English - 51
setup
” BLC Setting
You can selectively choose a screen area to see objects within the
area more clearly than others.
BLC
MEDIUM
- Four-direction Joystick Controls :
Moving the joystick in all four directions—upward, downward,
left, and right—adjusts the location and size of a selected area.
- Zoom Control :
y Zoom Tele : Enlarges the size of a selected area.
y Zoom Wide : Reduces the size of a selected area.
1 + PST : Level Change
m: Up n: Down
k: Left l: Right
W: Decrease T: Increase
AGC(Auto Gain Control)
AGC (Automatic Gain Control) adjusts the camera’s gain control
and the screen brightness if the camera has captured an object
under low-light conditions.
z OFF:
AGC does not function.
z LOW/MEDIUM/HIGH:
As the level increases to HIGH, brighter the captured screen in a
dark lighting.
z MANUAL:
AGC can be fine tuned by adjusting the level (5dB ~ 41dB).
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
52_ setup
ATW
OFF
High
Medium
SSNR(Samsung Super Noise Reduction)
SSNR significantly reduces the amount of low luminance noise.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
- OFF : Disables the noise reduction function.
- LOW : Reduces only a small amount of noise, but generates
almost no afterimage.
- MEDIUM : The most commonly used mode. Reduces a suitable
amount of noise while generating a subtle afterimage.
- HIGH : Reduces noise significantly, but generates obvious
afterimages.
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
High
Medium
M  SSNR is not available if AGC is set to OFF or MANUAL.
English - 53
setup
SSDR(Samsung Super Dynamic Range)
SSDR illuminates darker spots of an image while retaining the same
light level for brighter spots to even out the overall brightness of the
image with high contrast between bright and dark spots.
SSDR ON
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
SSDR OFF
Æ
Camera Setting
- Mode : Enables or disables SSDR.
- Range : Defines a range of SSDR.
- Level : Changes the contrast between bright and dark spots by
the level.
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
High
Medium
Æ
SSDR
偓Mode
Range
Level
54_ setup
ON
NARROW
08
Day & Night
The Day & Night function allows the camera to switch between the
Color and B/W modes.
- AUTO : Operates in Color mode most times, and switches
to B/W mode if a low light level is detected during
nighttime.
- COLOR : Operates in Color mode at all times.
- B/W : Operates in B/W mode at all times. By using the Burst
On/Off sub menu, burst signals can be retained or
disabled.
Ú If the camera is in B/W mode and connected to equipment
that requires external sync through burst signals, set the Burst
On/Off option to “On”.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
z MODE
Main Menu
Æ
Camera Setting
z Duration :
- The camera’s light sensitivity is adjustable as in the chart
below. The camera’s ambient light diversion performance
may vary depending on its environment.
Color p B/W
B/W p Color
FAST
2.5Lux
4Lux
SLOW
0.8Lux
6Lux
z Dwell Time :
- The duration of both the lighting conditions can be customized to
let the camera divert between the daytime and nighttime settings.
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
High
Medium
Æ
Day/Night
Mode
Duration
Dwell Time
AUTO
SLOW
05 SEC
M  Auto mode is not available if AGC is set to OFF or MANUAL. Only available if it is set to COLOR or B/W.
 Using B/W mode under sunlight or a halogen lamp may decrease the focusing performance.
English - 55
setup
Others
z Sync : Select Internal or Line Lock (Not applied to SCP-XXXXT).
- INTERNAL : Synchronizes the camera’s output timing to the
internal crystal.
- LINE LOCK : Synchronizes the camera’s output timing to
the AC adapter power to synchronize multiple
cameras. This option is useful when using a
switch such as Matrix Switcher.
- LINE LOCK PHASE : Enables setting the adapter’s
synchronization phase between 0 and 359°.
z Image Adj :
- Sharpness : Sharpens outlines of an image.
- Color : Adjusts the color density of an image.
z Freeze : Stops or reanimates an image.
z Stabilizer : The Stabilizer compensates for any small
movements of the camera caused by due to the
wind and other reasonable causes
Stabilizer uses the digital zoom and may cause low picture quality.
M  The
The Stabilizer is disabled if the ambient light is too low.
 The Stabilizer is disabled if the field of view has very low or no contrast,
e.g. The sky or a white wall.
z VPS (Virtual Progressive Scan) (SCP-3370 Series) :
Virtual Progressive Scan provides a clearer view of objects,
which is used for high-quality video. It is suitable for
highquality recording and Internet transfer.
- OFF : Switch the video recording system to 2:1 Interlace Scan.
- ON : Switch the video recording system to Virtual Progressive Scan.
z PIP (Picture in Picture) (SCP-3370 Series) :
PIP enables you to display the main image along with a
collapsed version of the main image.
M  The PIP feature will be disabled if using Auto Tracking or Area Masking.
z Dome Cover (Indoor Model) :
The existence of the dome cover will minimize the quality
difference according to the image formation position.
- OFF : If removing the dome cover before use
- ON : If using the product by factory default (using the dome cover)
56_ setup
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
High
Medium
Æ
Others
Sync
Image Adj
Freeze
Stabilizer
VPS
PIP
Dome Cover
INTERNAL
OFF
OFF
OFF
OFF
ON
Sequence Setting
Preset
z Setting Up Preset Numbers :
Selecting the Preset Setting menu brings up a screen as shown
below. Move the joystick in all four directions to select the desired
number.
Preset Setting
Preset = 001 (1~255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
041 : þþþþþþþþþþþþþþþþþþþþ
061 : þþþþþþþþþþþþþþþþþþþþ
081 : þþþþþþþþþþþþþþþþþþþþ
101 : þþþþþþþþþþþþþþþþþþþþ
121 : þþþþþþþþþþþþþþþþþþþþ
z Saving Preset Locations :
Selecting a preset number and pressing the Enter key redirects
the menu to the screen shown below.
Using the joystick, adjust the location of the Pan and Tilt
functions and then set the Zoom and Focus command.
In Preset Settings, the Zoom and Focus command is controllable
only by the Zoom command.
Preset Setting
Main Menu
● SETUP
This function enables the memorization of a selected location and
activates the Pan, Tilt, and Zoom functions at that location. Saved
locations can be recalled using the Preset Execute command.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
ON
Æ
Preset
Setting
Edit
Home Position
Execute
Clear
Status
OFF
1+PST:ZOOM 2+PST:FOCUS
English - 57
setup
” PTZF Setting
1. If you open the PTZF setup menu, you will see the following
window. You can use the joystick to select a desired number.
Preset Setting
Preset = 001 (1~255)
2. Select a preset number and press ENTER. You will move
to the setup screen.
Using the joystick, adjust the location of the Pan and Tilt
functions and then set the Zoom and Focus command.
In Preset Settings, the Zoom and Focus command is
controllable only by the Zoom command.
For switching modes, refer to the menu bar in the bottom.
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
Æ
Preset Setting
1+PST:ZOOM 2+PST:FOCUS
” Edit
With this feature, you can edit or save the video-related
settings for each preset of the camera.
- PTZ : Recalls saved locations using the Preset Settings command.
- Focus : Refer to the section entitled Setting Up Your Camera.
- Brightness : Refer to the section entitled Setting Up Your Camera.
- Iris : Refer to the section entitled Setting Up Your Camera.
Preset
Setting
Edit
Home Position
Execute
Clear
Status
OFF
- Back Light : Refer to the section entitled Setting Up Your Camera.
Æ
- Day & Night : Refer to the section entitled Setting Up Your Camera.
- After Action : Enables setting up an automatic action after the
camera arrives at a selected preset location.
. AUTO TRACK : Commands the camera to perform the Auto
Tracking function.
. MD : Commands the camera to perform the Motion Detection function.
If Focus mode is set to Auto, the MD function may not work
properly in a challenging environment.
. OFF : Select this when no action is desired.
- Others : You can set AGC, Stabilizer, SSNR, SSDR, Shutter,
Sens-Up and White Balance functions. For terms related
to settings, refer to the camera settings commands.
58_ setup
Preset Setting
Preset = 001Ã (1~255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
Æ
Preset Edit
[001]
PTZ
Focus
Brightness
Iris
Back Light
Day & Night
After Action
Scene Adj
180/025/1X
ONE SHOT
050
AUTO
OFF
AUTO
OFF
Motion Detection / Intelligence (SCP-3370 Series)
This will enable you to detect and trace a moving object. SCP-3370 series support the intelligent motion
detection feature.
For the compatibility of this feature, refer to the table below.
Features Applied
SCP-2370/2370H/2330/23370H/2270/2270H
OFF / MD
SCP-2370TH
OFF / MD / AutoTrack
SCP-3370/3370H
OFF / Detection / Tracking / Fixed/Moved
SCP-3370TH
OFF / Detection / Tracking / Fixed/Moved / AutoTrack
● SETUP
Model
z AutoTrack :
Perform Auto Track after arriving to the preset position.
z Detection :
Perform the intelligent motion detection.
DETECTION
- Detect Box: Display an object in a box that is detected to move in
Detect Box
your specified type.
Detect Area
- Detect Area : You can specify a motion detection area.
Mask Area
- Mask Area : You can specify an exceptional area to motion
Sensitivity
detection by masking the area.
Det. Size
You can set up to 4 areas, for each of which you can
change the mask coordinates.
- Sensitivity : Specify the sensitivity level of the motion detection.
The lower the level is, the stronger the sensitivity becomes.
- Detect Size : Specify the size of an object to detect on the screen.
The higher the level is, the greater the size becomes.
ON
z Fixed/Moved :
Detect if an existing object (on the screen) disappears or if an object appears from nowhere and
stays for a certain time.
M  In following situations, FIXED/MOVED detection may not work properly.
➊ If multiple motions continue at random.
➋ If a fixed object continues to move in the same position.
➌ If a newly appearing object conceals another object that is moving.
 5 to 15 seconds of recognition time is required if the [Intelligence] function is activated.
 The focus mode will be controlled manually if [Intelligence] is enabled.
 The performance of [Intelligence] may be deteriorated if the camera vibrates due to unstable installation.
English - 59
setup
z Tracking :
This will detect and trace a moving object. You can use the fence
function to count the moving objects. The default setting is the
same as in the Detect menu, to which the Fence Position function
is added.
- Fence : Specify the position and detectable direction of the line
fence or area fence, depending on the fence type.
- Display: Specify the display of the fence status.
- Type : You can select one of two types for the fence LINE and
AREA.
- Count : Display the number of times that an object enters or exits
from the fence.
M
 In some cases, the Count function may have a difference between number
of the detected objects and counter number.
- Fill : Specify the use of color fi lling on the selected fence.
TRACKING
Fence
Detect Box
Detect Area
Mask Area
Sensitivity
Det. Size
ON
Æ
Fence
Display
Type
Count
Fill
Position
ON
LINE
OFF
OFF
- Position : Specify the position and detectable direction of the line
fence or area fence, depending on the fence type.
 LINE FENCE
- SEL POS: Select a changing point from position 1 and
position 2.
- X POS/Y POS: Specify the position of the changing point that
you have selected in the SEL POS menu.
Fence
SEL POS
X POS
Y POS
DIRECTION
POS1
20
3
DIR 1
- DIRECTION:
DIR 1: Detect an object that moves from left to right based on the specified fence line.
DIR 2: Detect an object that moves from right to left based on the specified fence line.
DIR 1/2: Detect an object that moves in any direction of right to left or left to right based on the
specified fence line.
 AREA FENCE
- SEL POS:Select a changing point from position 1 through
position 4.
- X POS/Y POS:Specify the position of the changing point that
you have selected in the SEL POS menu.
Fence
SEL POS
X POS
Y POS
DIRECTION
- DIRECTION:
IN: Detect any object that enters the specified fence area.
OUT: Detect any object that exits from the specified fence area.
IN/OUT: Detect any object that enters or exits from the specified fence area.
60_ setup
POS1
20
3
IN1
” Preset Name Setting
Using this function, you can add names to preset locations.
up to 12 characters.
Once a name is entered, use the joystick and the Enter key to
perform the Set command and save the name.
Main Menu
● SETUP
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
OSD Setting
Camera ID
Camera Name
Preset Number
Preset Name
....
ON
ON
Æ
Preset Name
On/Off
Edit
OFF
Æ
Preset Name
Preset = 001* (1~255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
Æ
Preset Name
[
" # $ % & '( ) * + , - .
/0123456789:;
BCDEFGHIJKLMN
OPQRSTUVWXYZ[
<> T Â ]
BACK SPACE CLR SET
English - 61
setup
” Home Position
Sets one of the currently configured preset positions as the home
position.
” Execute
Preset
Setting
Edit
Home Position
Execute
Clear
Status
OFF
Preset
Recalls a saved preset location.
While in Sequence mode operation, the actual movement can
be slower than the specified when moving the camera in the
direction of Pan and Tilt at the same time.
Setting
Edit
Home Position
Execute
Clear
Status
OFF
” Clear
Deletes the selected preset location.
Preset
Setting
Edit
Home Position
Execute
Clear
Status
OFF
” Status
Opens a map of saved preset locations.
An area saved as a preset location is displayed with the ‘ ’ icon.
Preset Status
Preset Status
001 : þþþþþþþþþþþþþþþþþþþþ 161 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ 181 : þþþþþþþþþþþþþþþ þþþþþ
041 : þþþþþþþþþþþþþþþþþþþþ 201 : þþþþþþþþþþþþþþþ þþþþþ
061 : þþþþþþþþþþþþþþþþþþþþ 221 : þþþþþþþþþþþþþþþ þþþþþ
081 : þþþþþþþþþþþþþþþþþþþþ 241 : þþþþþþþþþþþþþþþ
101 : þþþþþþþþþþþþþþþþþþþþ
121 : þþþþþþþþþþþþþþþþþþþþ
141 : þþþþþþþþþþþþþþþþþþþþ
62_ setup
Preset
Setting
Edit
Home Position
Execute
Clear
Status
OFF
Swing SEQ
The Swing function commands the camera to move between 2
selected locations, monitoring the route.
Activates the Pan function for the Swing operation.
z Tilt Swing :
Activates the Tilt function for the Swing operation.
z P/T Swing :
Activates both the Pan and Tilt functions for the Swing operation.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
z Swing Setting/Execute/Clear
Each of the Swing menus have sub menus with the settings.
Pan Swing
Setting
Execute
Clear
Æ
Pan Swing
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
[ÂÂÂ]ƒ„[ÂÂÂ]
Speed =64 (1~64)
Dwell Time =005(1~120) (s)
● SETUP
z Pan Swing :
Main Menu
ON
Æ
Swing SEQ
Pan Swing
Tilt Swing
P/T Swing
Select 2 preset locations by using the joystick.
Speed indicates the camera’s movement speed. DWELL TIME indicates the camera’s duration of stay at a
preset location.
- Execute: Executes the Swing operation.
- Clear: Deletes data in the Swing memory.
in Sequence mode operation, the actual movement can be slower than the specified when moving the camera in the
M  While
direction of Pan and Tilt at the same time.
English - 63
setup
Group SEQ
Selecting Group SEQ recalls a group of multiple preset locations in a
consecutive manner. Up to 6 groups can be defined and up to 128
presets can be memorized for each group.
z Setting :
Using the joystick,enter desired preset numbers into the PSET
section. DWT indicates the camera’s duration of stay at a preset
location.
The speed is adjusted in 64 levels.
Group SEQ 1
NO
001:
002:
003:
004:
005:
006:
007:
PSET
*** :
*** :
*** :
*** :
*** :
*** :
*** :
DWT(s)
003 :
003 :
003 :
003 :
003 :
003 :
003 :
SPD
64
64
64
64
64
64
64
z Execute :
Executes the group operation.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
Æ
z Clear :
Deletes the selected group.
8 seconds of recognition time is required if [Intelligence] of the preset
M  About
is activated from the Group menu.
 For a proper operation of [Intelligence], set [Time (sec)] of the Group menu
to more than 8 seconds.
64_ setup
Group SEQ
Group 1
Group 2
Group 3
Group 4
....
Æ
Group SEQ 1
Setting
Execute
Clear
ON
Tour SEQ
Selecting Tour SEQ recalls groups of preset locations in a
consecutive manner. Up to 6 groups can be listed for this function.
Selecting the Settings menu brings up the following screen.
Using the joystick, you can enter desired group numbers to the
Group section. DWT indicates the camera’s standby time before
a new group is recalled.
Tour SEQ
NO
01:
02:
03:
04:
05:
06:
Group
*
*
*
*
*
*
DWT(s)
003
003
003
003
003
003
z Execute :
Executes the group operation.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
z Setting :
Main Menu
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
z Clear :
ON
Æ
Deletes the selected group.
Tour SEQ
Setting
Execute
Clear
English - 65
setup
PTZ Trace
Maximum 4 patterns of the manual operation paths (for Pan, Tilt,
Zoom and Focus) are memorized and replayed.
z Replay :
Replays a route saved by the Trace function.
z Replay Once :
Replays a saved Trace route once.
z Memorize :
The time for storing the event differs depending on the
complexity of PTZ operations of your choice. When the memory
is full, any further storing will be stopped.
You can use the Menu button (OSD access key) to stop the
memorize function during its process.
Ú Using other protocols
Protocol
Representative
Model
Stop saving the
trace
PELCO-D/P
KDB300A
Ack, Iris Open
SAMSUNG-E
SSC-5000
OSD ON, Iris Open
PANASONIC
WV-CU161C
OSD ON
VICON
V1300X-DVC
Iris Open
HONEYWELL
HTX-3000
Iris Open
OSD ON, Iris Open
AD
GE
KTD-405
Bosch
z Clear : Deletes a saved Trace route.
Iris Open
Iris Open
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
Æ
PTZ Trace
Trace 1
Trace 2
Trace 3
Trace 4
Æ
Trace 1
Replay
Replay Once
Memorize
Clear
66_ setup
ON
Auto Run
If there is no controller operation by the user for a certain time, the
sequence operation designated by the user will be executed.
- HOME : Auto run Home Position (Refet to the Preset Menu.)
- PRESET : Auto run a selected preset number.
- SWING : Auto run a selected Swing mode.
- GROUP : Auto run a selected Group mode.
- TOUR : Auto run a selected Tour mode.
- TRACE : Auto run a selected trace mode.
- A.PAN : Auto run a 360-degree pan. To activate the
panning command, you need to set up the
camera’s tilt angle and auto pan speed manually.
- SCHEDULE : Execute Auto Run on the selected day of the
week.
z Time :
Enables setting up an Auto Run duration. (The duration can be 5~30
seconds, or 1~5 minutes.)
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
z Mode :
Main Menu
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
ON
Æ
Auto Run
Mode
Time
OFF
20 SEC
English - 67
setup
” Schedule
Schedule enables you to schedule a sequencing action by day and time.
z Select Day :
At Auto Run, select SCHEDULE to set up each day of the week,
as shown on the side picture. Select a day, change to ON, and
then press Enter.
z Select Time :
When turning ON a day, a timetable appears as shown on the
side picture. (Up to 6 timelines can be selected for a day.) Select
the beginning time and sequencing action to schedule the action.
Auto Run
Mode
Time
SCHEDULE
20SEC
Æ
Schedule Set
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
ON
OFF
OFF
OFF
OFF
OFF
OFF
Æ
Schedule Set
No START
1
09:00
2
00:00
3
00:00
4
00:00
5
00:00
6
00:00
Clear
SEQ
HOME
OFF
OFF
OFF
OFF
OFF
No
Power On Resume
Main Menu
z Power On Resume :
This is useful when the power is disconnected and reconnected
due to power failures or other power interruptions.
If the camera was performing a sequence action prior to a power
disconnection, the camera automatically resumes the action
when the power is reconnected.
Camera Setting
Sequence Setting
P/T Setting
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
68_ setup
ON
P/T Setting
Pan/Tilt Limit
Main Menu
z Position :
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Selecting the Position menu brings up the following screen if it is
for the Pan Limit setting. Move the joystick left and right to select
a movement range from the starting point to the end.
START LIMIT
END LIMIT
Enter: Set ESC: Exit
Enter: Set ESC: Exit
The following picture shows the Tilt Limit setting.
Move the joystick left and right to select a movement range from
the starting point to the end.
START LIMIT
Enter: Set ESC: Exit
END LIMIT
Enter: Set ESC: Exit
z Activation :
Sets the configured Pan/Tilt Limit function to use or not.
● SETUP
The moving ranges in the Pan/Tilt directions can be limited.
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Auto Tracking
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
6
Æ
Pan/Tilt Limit
Pan Limit
Tilt Limit
Æ
Pan Limit
Position
Activation
OFF
English - 69
setup
Area Setting
The Area Setting menu enables selecting certain locations in the
course of the Pan and Tilt operation, and then display the areas with
the OSD (On Screen Display) texts when the camera passes through
them. Up to 8 areas can be selected.
z Area Name :
You can add names to selected areas. Names can be up to 12
characters and can be entered via the joystick and the Enter key.
Once a name is entered, use the joystick and the Enter key to
perform the Set command and save the name.
Area Name
[
]
" # $ % & '( ) * + , - .
/0123456789:;
BCDEFGHIJKLMN
OPQRSTUVWXYZ[
<> T Â BACK SPACE CLR SET
z Position :
As shown in the picture below, move the joystick to select the upper
left corner and lower right corner of an area.
Area Setting
Enter: Set ESC: Exit
Area Setting
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Auto Tracking
Jog Speed
Max Speed Level
Enter: Set ESC: Exit
The effective positioning range is between -45° and 40° in the
tilting angle at the zoom factor of 1x.
z Activation :
Cancels or activates the display function of selected areas.
ON
ON
OFF
MANUAL
6
Æ
Area Setting
Area 1
Area 2
Area 3
Area 4
....
Æ
Area 1
Area Name
Position
Activation
70_ setup
OFF
Area Masking
If a monitoring location includes a highly private area, the area can be selectively excluded from monitoring.
Main Menu
z Position :
Area Masking
Area Masking
Enter: Set ESC: Exit
Enter: Set ESC: Exit
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
- SCP-2XXX Series
As shown in the picture below, move the joystick to select the upper
left corner and lower right corner of an area.
Æ
- SCP-3370 Series
As shown, specify the masks in the order of: top left p top right p
bottom right p bottom left.
Area Masking
Area Masking
Enter: Set ESC: Exit
Enter: Set ESC: Exit
Area Masking
Area Masking
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Auto Tracking
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
6
Æ
Area Masking
Enter: Set ESC: Exit
Enter: Set ESC: Exit
Use the joystick in four directions to specify the masks that you want
to exclude from the area masking.
 However, SCP-3370TH operates the same as SCP-2XXX series.
z Activation :
Activate or deactivate the display of specified masks.
model supporting Auto Track (SCP-XXXXTH), the PIP feature
M  Forwill abeproduct
disabled if using Area Masking.
Mask 1
Mask 2
Mask 3
Mask 4
....
Æ
Mask 1
Position
Activation
OFF
English - 71
setup
Prop. P/T
This commands the camera to change the Pan and Tilt speed
automatically according to the current zoom ratio. Moving the
joystick clockwise (Tele) slows down and counterclockwise (Wide)
accelerates the Pan and Tilt speed, allowing detailed adjustments.
Turning this “Off” executes the function the optical 1x zoom speed
regardless of how far the lens is zoomed in.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Auto Tracking
Jog Speed
Max Speed Level
72_ setup
ON
ON
OFF
MANUAL
6
Digital Flip
z 0° → 180° : Image flip at the 93-degree point
z 180° → 0° : Image flip at the 87-degree point
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
Digital Flip is useful to monitor a moving object or a person passing
directly under the camera.
When the object passes straight under the camera, tilting can be
traced up to the opposite tilting area without the need of the pan
operation. The reverse screen that occurs when the object gets
through the 90-degree point will be corrected in digital processing.
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Auto Tracking
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
6
English - 73
setup
Image Holding
This will display the preset video in still images until the orientation
of the camera reaches the preset position at a group or tour
movement.
This is useful if you want to monitor the video while preventing a
possible visual distraction of the observer.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Auto Tracking
Jog Speed
Max Speed Level
74_ setup
ON
ON
OFF
MANUAL
6
Auto Track (SCP-XXXXT)
This function is to instruct the camera to track a moving object on the screen.
z Auto Track :
z Zoom Control :
The function’s zoom control settings are as follows.
- Off : Disables the Zoom control.
- ONE SHOT : Performs the Zoom control once during the Motion
Detection and Auto Track operations. Depending on the movement
detection, the camera performs the Zoom control multiple times.
- Continuous : Performs the Zoom control continuously.
z Auto Release :
Enables setting a maximum duration to follow an object. When the
duration expires, the camera stops following the object and returns
to the start position to follow another objects.
z Auto Return :
- Off : Commands the camera to stay on the location the last object
stopped at instead of returning to the initial position.
- Time Setting : Sets a duration for the camera to standby upon the Auto
Release expiration and then return to the start position.
z Lost Mode :
Sets up an action for the camera in case the object it is following
goes out of the detection range.
- Stop : Commands the camera to stop and abort tracking at the spot
where its object disappeared.
- Research : Commands the camera to stop and standby at the spot
where its object disappeared.
- Zoom Out : Commands the camera to zoom out and look for a new
object in case its current object disappears.
Main Menu
● SETUP
- ON/OFF : Turns Auto Tracking on or off.
z Camera Height :
- Adjusts the height of the camera. Tracking performance may
decrease if the camera height is not adjusted properly.
(Height: 2.5m ~ 30m)
z Object Size :
Sets a maximum zoom ratio to zoom in on an object if the Zoom
function is used for the tracking operation.
- Small : Zooms in on a tracking object up to 1/4 of the screen height.
- Medium : Zooms in on a tracking object up to 2/4 of the screen height.
- Large : Zooms in on a tracking object up to 3/4 of the screen height.
z Sensitivity :
Specify the sensitivity of tracking an object when using Auto Track.
- LOW/MEDIUM/HIGH: The higher the sensitivity is, the camera
can track a slightest movement. Decreasing it will track only a
greater movement.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Auto Tracking
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
6
Æ
Auto Tracking
Auto Track
Camera Height
Object Size
Sensitivity
Zoom Control
Auto Release
Auto Return
Lost Mode
Others
OFF
2.5M
SMALL
HIGH
OFF
OFF
OFF
STOP
English - 75
setup
z Others :
Here you can configure the settings of other options than Auto Track.
- Zone Setting :
f Position : Enables the designation of certain areas as zones for the Auto Track operation.
The setting procedures are the same as for Area Mask.
f Mode : Two modes are available: Mask and Alarm. When Mask is selected, the camera does not
follow the object entering the masked zone. This is useful if the camera catches swaying
objects such as tree branches and flags during the Auto Track peration.When Alarm is
selected, the camera activates an alarm if an object enters the zone.
f ON/OFF : Activates or deactivates the Zone function.
- Indicator : Indicates objects with icons on the screen.
f OFF: Do not display the indicator.
f Indicator (
) : Indicates both the pointer and target.
f Indicator 1 (
) : If a movement is detected, a cross mark will be displayed in the center of the screen.
f Indicator 2 (
) : when a moving object is detected, a square grid appears and surrounds the object.
- Target Lock : Target Lock is useful to select and follow an object using the Auto Track mode while
operating the camera with the joystick. Target Lock can be turned On or Off.
To activate the Auto Track mode, turn on Target Lock, select an object to follow, and
then press Enter.
for using Auto Track
M  yNotes
Auto Track is specifically to track down intruders. Thus, it may not be suitable to monitor a crowd.
y If the camera is not safely secured, tracking errors may occur.
y An error may occur due to impurities or stains piling up on the dome cover of the camera.
y Auto Track may not perform what you expected in a certain environment or condition.
y The camera may not follow an object or tracking errors may occur under the following conditions:
- If the contrast between an object and the background is low
- If the camera lens is smeared with foreign substances, e.g. raindrops or snowflakes
- If the lighting is changing dramatically
- If many movements around an object are detected
- If an object moves vertically on the optic angle of the camera
- If an object moves right under the camera installation position
- If an object creates inconsistent light levels, e.g. the object is too shiny or flickering
- In environments where there are light reflections causing internal reflections of camera, e.g. windows, shiny road
-
76_ setup
surfaces, and backlights
If an object moves behind large and tall objects, e.g. telephone poles
If an object moves too quickly
If the camera is vibrating
Jog Speed
You can adjust the speed of the pan or tilt operation. The pan/tilt speed changes according to the tilt of
the joystick, or you can control the operation in a fixed speed.
The pan/tilt speed depends on how much the joystick of the
controller is tilted. The more the joystick is tilted, the faster the
operation is performed.
z 30/35/40/45/50/55/60 :
The pan/tilt operation will be performed at the selected speed; the
greater the number is, the faster the operation is performed.
However, the speed at each level may differ according to the
zooming status, and depending on the use of synchronized
zooming.
● SETUP
z MANUAL :
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Auto Tracking
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
6
English - 77
setup
Max Speed Level
Adjusts the maximum speed of Pan and Tilt while performing the Preset and Sequencing actions.
z 1~7 :
Pan and Tilt operations can be set up to 600°/ sec.
Ú Preset speed for each level
Level
Speed (Unit: º/sec)
7
600
6
560
5
500
4
450
3
400
2
360
1
300
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
M  The Pan/Tilt speed will be reduced at below -40°.
78_ setup
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Auto Tracking
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
6
OSD SETTING
In this menu, you can configure the OSD (On Screen Display) settings.
Main Menu
z Camera ID :
z Camera Name :
Add a name to the camera. (First check the Note.)
z Preset Number :
Displays or hides Preset Numbers on the screen.
z Preset Name :
Add names to preset locations. (First check the Note.)
z Seq. Status :
Displays or hides the status of a sequence action that is in
progress.
● SETUP
Displays or hides Camera ID in the upper left of the screen.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
OSD Setting
z Area Name :
Displays or hides the Area Name for the Area Settings on the
screen.
z PTZ Position :
Displays or hides the status of the Pan, Tilt, and Zoom operation
that is in progress.
z Language :
Enables changing the system language. This camera supports
ENGLISH, CHINESE, FRENCH, GERMAN, SPANISH, ITALIAN,
PORTUGUES, POLISH, RUSIAN, CZECH, TURKISH, KOREAN,
JAPANESE, TAIWANESE.
Camera ID
Camera Name
Preset Number
Preset Name
Seq. Status
Area Name
PTZ Position
Language
ON
ON
ON
OFF
ON
ENGLISH
z Others
- Direction : Indicates the current angle of the camera:
East, West, South, North, Southeast, Southwest, Northeast, or Northwest.
- Clock Setting : You can configure the time related settings.
XXX Name
[
]
" # $ % & '( ) * + , - .
/0123456789:;
BCDEFGHIJKLMN
OPQRSTUVWXYZ[
<> T Â selecting the Camera Name and Preset Name, the screen displays the Left
M  When
keypad.
 Names can be up to 12 characters and can be entered via the joystick and the Enter
key. Once a name is entered, use the joystick and the Enter key to perform the Set
command and save the name.
BACK SPACE CLR SET
English - 79
setup
ALARM SETTING
Alarm Enable
Main Menu
z ON/OFF :
Enables or disables the Alarm function.
Alarm Input
z MOD
Enables selecting an Alarm Input method.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
- NO (Normally Open)
Æ
Alarm Setting
IN 1.2.3.....8
IN 1.2.3.....8
Ä
ALM GND
ALM GND
ALARM OFF
Alarm Enable
Alarm Input
Alarm Output
MD Dwell Time
ALM Dwell Time
OFF
HOLD
ALARM ON
Æ
< Alarm input when N.O. is enabled >
- NC (Normally Closed)
ALM MOD P SEQ. NO
IN 1.2.3.....8
IN 1.2.3.....8
Ä
ALM GND
OFF
IN1 OFF
IN2 OFF
IN3 OFF
.....
1 OFF
2 OFF
3 OFF
ALM GND
ALARM OFF
ALARM ON
< Alarm input when N.C. is enabled >
shown in the picture above, the Alarm Input must be entered with the Open or Closed switch signals. Supplying power
M  Aswithout
entering the signals may damage the product.
80_ setup
z P(Priority) :
Set the priority of Alarm Inputs. If more than one alarm is simultaneously activated,
the alarm with the highest priority activates before the others. Once the alarm is canceled, the next
highest priority alarm activates.
z SEQ. :
● SETUP
Enables setting up a sequence action for the camera in response to an alarm.
You can configure the settings of: HOME/PRESET/SWING/GROUP/TOUR/TRACE/A.PAN/OFF
Alarm Output
Main Menu
z Setting 1, 2, 3 :
Enables selecting an Alarm Output method.
- DETECT MODE : Displays the alarm input ports (1~8) and the
motion detection input. If you set MD Input,
you can select one from: OFF/MD/A.TRACK/
MD+A.TRK.
- AUX MODE : Alarm Output 1 and 2 feature N.C/N.O while Alarm
Output 3 is specific to N.O. only.
z Timer 1, 2, 3 :
- On : Retains an alarm output for a set duration from a
minimum of 1 second to a maximum of 60 hours upon
the alarm occurrence.
- MOMENT : Retains an alarm output only until the alarm is canceled.
- The Alarm Output is equipped with a relay circuit. The
operation of the alarm output port is as shown in the diagram
below. (Based on NO – Normal Open)
/0
$0.
/$
Alarm Out OFF
/0
Ä
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Alarm Setting
Alarm Enable
Alarm Input
Alarm Output
MD Dwell Time
ALM Dwell Time
$0.
/$
Alarm Out ON
z OUT Off 1, 2, 3 :
- When an alarm event occurs, the output force can be
terminated.
OFF
OFF
HOLD
Æ
Alarm Output
Setting
Setting
Setting
Timer
Timer
Timer
Out Off
Out Off
Out Off
1
2
3
1
2
3
1
2
3
DETECT MODE
DETECT MODE
DETECT MODE
OFF
OFF
OFF
English - 81
setup
the power connector and GND incorrectly to the NC/NO and COM ports may cause a short circuit and fire,
M  Connecting
damaging the camera.
 The maximum power capacity of the built-in relay is 30VDC/2A, 125VAC/0.5A, and 250VAC/0.25A. Operating the
camera beyond the capacity may decrease the camera’s lifespan and damage it.
MD Dwell Time
When Motion Detection under the Preset Edit menu is selected,
MD Dwell Time performs the Tour or Group function.
While the camera is performing a sequence action, if motion is
detected from a selected preset location, the camera pauses
the sequence action operation and starts monitoring the location
instead for a duration that is set under the MD Dwell Time menu.
If the motion is no longer detectable or the duration expires, the
camera aborts the monitoring operation and then resumes the
sequence action.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Alarm Setting
Alarm Enable
Alarm Input
Alarm Output
MD Dwell Time
ALM Dwell Time
OFF
OFF
HOLD
ALM Dwell Time
You can specify the time of sequence operation that will be activated if an event occurs from the alarm
input.
z SET:
The sequence operation will proceed for a specified time.
z HOLD:
The sequence operation will be maintained until the user deactivates it.
82_ setup
INITIALIZE
z Power On Reset :
Restarts the camera.
z Factory Default Set :
z Camera Default Set :
Reset the zoom module of the camera to the factory default. Use
this if you want to return the camera settings of such as Exposure
or Backlight to the factory default.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
z Auto Refresh :
Optimizes the settings of the electric circuits and component parts
of the camera on a regular basis.
This is useful for maintenance purpose, especially when the
camera faces a specific light source, or if the camera settings are
not maintained properly due to an extended time of recording
while rotating the camera in four directions.
- Off, 1~7 Days : Selecting Off disables Auto Refresh and selecting
1~7 Days automatically executes it after 1~7 days has passed.
Ú Auto Refresh takes about 10 seconds or less. Any sequence
operation that is being performed will be stopped and resume
after Auto refresh is completed.
● SETUP
Enables resetting the camera to its factory default settings. When
the mode is selected, all custom data such as preset locations is
deleted from the camera.
Use this function if it is necessary to reset the settings of the
camera.
Main Menu
Initialize
Power On Reset
Factory Default Set
Camera Default Set
Auto Refresh
OFF
Auto Track Default
Fan Life
z Auto Track Default (Applied only to Auto Tracking models) :
Enables resetting the Auto Track settings.
z Fan Life (Applied only to Environmental models) :Enables setting the Fan Life.
- Message Display: The following warning message will appear 2 months before the expiry of the fan
life. “Fan Life Expired. Replace the Fans”
f ON: Display the warning message. (Default)
f OFF: Do not display the warning message.
Ú [OFF] is to hide the message, rather than to delete it. Set it back to [ON]. Then, the warning
message will appear. (Only if you didn’t clear the message [Message Clear])
- Message Clear: Use this if you want to delete the warning message when it pops up.
Ú If you set [Message clear] to [On]after performing the command, no warning message will appear
on the screen.
- Time Reset: Set to count the fan life again after replacing the fan. (However, this is available only
after you see a warning message that the fan life has expired.)
Ú The fan life is counted only for an actual operation so the fan can be used longer than the
displayed time.
- Time Remain.(hour):
f 49000 : Remaining life of fan (unit: hour)
f The fan life will be updated when you access the [Fan Life] menu and if you press [ENTER] on the
[Time Remain.(hour)] item.
English - 83
setup
PASSWORD SETTING
The Password feature enables you to configure a password for
rebooting the camera and accessing the OSD and preventing
unauthorized modification of existing camera settings.
z On/Off :
Enables or disables Password protection.
z Edit Password
Change the password; enter the current password and then a
new one, consisting of 4 hexadecimal characters (0~F).
 The default password is "0000".
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Password Setting
On/Off
Edit Password
OFF
STATUS
Displays the settings and version of the camera.
Main Menu
z CAM MODEL :
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Indicates the model name of the camera.
z CAM VER. :
Indicates the software version of the camera.
z DOME VER. :
Indicates the version of the camera control board.
z COAX VER. :
Indicates the software version of the Coax communication
z TRACK VER. (Applied only to Auto Tracking models):
Indicates the Auto Track software version of the camera.
z PROTOCOL :
Indicates the status of the current protocol.
z DOME ID :
Dome Camera ID
z CONTROLLER :
Indicates the settings of the current communications mode.
84_ setup
Æ
Camera Status
CAM MODEL
CAM VER.
DOME VER.
COAX VER.
TRACK VER.
PROTOCOL
DOME ID
CONTROLLER
= SCM2370/PAL
= V2. 02-101024
= V0. 08-101023
= V0. 02-101207
= V1. 14-101206
= SAMSUNG-T
= 001
= Simplex
troubleshooting
TROUBLESHOOTING
If the product does not function properly, please see the below for trouble shooting.
Problem
Cause and Solution
Page
18~20
► Verify the setups of ID, protocol, and baud rates.
21~32
► Check if power cable is securely connected to the camera and the monitor.
Check if the video cable is properly connected. Consult the operation
manual of the system controller connected to the camera.
18~20
► Check if the iris of the lens is closed.
Adjust the menu for the iris of the lens.
49
► Check the camera’s fixed shutter speed.
Adjust the camera’s shutter menu.
49
The picture is too dark/bright.
► Check the camera’s Brightness menu.
Adjust the camera’s Brightness menu.
49
The monitor displays a white
image.
► Check if the iris of the lens is open.
Adjust the menu for the iris of the lens.
49
► Check if the dome cover or the camera lens is dirty or smudged.
If it is, clean the dirt off.
-
► Verify the distance between the camera and the subject, as well as the
subject’s surroundings. Camera may have difficulty focusing on a subject
against a white background.
-
► If Auto Focusing is having difficulty focusing on a particular subject, set
Focus Mode to Manual and adjust the focus by yourself.
47
► Use the camera’s reset menu to restore the camera settings in order to
default.
83
► Adjust Sharpness level.
56
► Check if the video cable is properly connected.
-
► Make sure that the power cable and video cable do not exceed the
recommended maximum lengths.
33
► Adjust Sharpness level.
56
No picture is displayed on
monitor.
Picture is out of focus.
Digital noise appears in picture.
English - 85
● TROUBLESHOOTING
► Check if the camera and peripheral devices are properly connected.
Controller does not work.
troubleshooting
Problem
Cause and Solution
Page
► Check the White Balance.
48
► Adjust Color Menu in Image Adj.
56
► Check if the dome cover or the camera lens is dirty or smudged.
If it is, clean the dirt off.
-
The picture is flickering.
► Check if the camera is pointing directly at a fluorescent light or sunlight. If
so, change the camera’s direction to remove the flickering.
-
Afterimages appear in picture.
► Check Sens-Up settings.
49
Camera switches between color
and B&W modes frequently.
► Adjust Duration and Dwell Time in Day & Night menu.
55
► Check if power cable is securely connected to the camera and the monitor.
Check if the video cable is properly connected.
Consult the operation manual of the system controller connected to the
camera.
18~20
► Check if Pan Limit and/or Tilt Limit are set.
If so, remove the limit(s).
69
► A motor or the lens may be overheated.
If so, contact your service personnel or system provider for assistance.
-
► This phenomenon may happen, since the motors have a margin error of ±0.1˚.
-
Picture’s colors are not good.
Pan, tilt, zoom, and/or focus do
not work.
The camera’s position differs
from the position defined in a
preset.
Sequence configuration of the
camera does not work.
The upper side of the picture is
dark when the camera is on the
horizontal reference point.
Camera suddenly turns on or
moves to a preset position by
itself.
86_ troubleshooting
► Check if Preset or another operation mode has been set.
► Check the Auto Refresh settings.
57~68
► You are seeing the camera's internal cover. The camera is functioning
normally.
-
► Check the Auto Run settings.
Auto Run puts a camera through a predefined action sequence if the user
does not use the Controller to operate the camera for a certain period of
time.
67
► Check the Auto Refresh settings.
Auto Refresh optimizes the camera's circuitry and components according
to a predefined schedule.
83
Problem
Auto Tracking suddenly functions
incorrectly.
A subject being Auto-Tracked is
out of screen immediately.
Coxial communication does not
work.
I turned on the power, but the
camera didn't start running.
(SCP-XXXXH Only)
Page
► Check if the subject is in an area set of Area Masking.
71
► Check the Auto Release settings.
Auto Release stops tracking a subject after a preset period of time, and
returns the initial position of the camera to track a new subject.
75~76
► Sensitivity may be set too low for the camera to detect a moving subject.
Adjust a higher Sensitivity setting.
75~76
► Check if the subject is too small.
Adjust picture angle to increase the subject size.
75~76
► Check if there are trees, grass, flags, or other subjects being moved by
wind, and/or water, glass, paved roads, or other subjects with a highly
reflective surface.
If so, set Area Masking of the area containing such subjects.
76
► The sensitivity of the camera's threshold detection may be set too high.
Adjust a lower Sensitivity setting.
77
► Check the weather conditions around you.
If the dome cover is contaminated with raindrops or snow, or is shrouded
in mist, it may not operate properly or at all.
-
► Check Object Size settings.
If Object Size is set too small, adjust it to a larger value.
75
► Check if the monitored area contains multiple moving subjects.
Auto Tracking is intended for monitoring intruders, and may not be suitable
for crowd monitoring.
-
► Check the distance between the camera and the monitor.
33
► If the distance between the camera and the monitor exceeds the
recommended maximum, please use an auxiliary video amp.
33
► Please check the environment temperature; the camera may not operate
properly if it has been left at temperatures lower than -50º for a prolonged
duration.
6~7
► The motor may malfunction at temperatures lower than -20º; please turn
on the camera in Standby mode instead of [Initialize].
6~7
► Keep in Standby mode for at least 120 minutes. Once the internal
temperature reaches -20º or higher, the camera automatically resets itself
and activates the [Initialize] mode for normal operation.
6~7
English - 87
● TROUBLESHOOTING
Although The subject is moving,
but Auto Tracking does not work.
Cause and Solution
troubleshooting
Problem
Cause and Solution
Page
► When the camera’s internal temperature drops down to -20º or lower, it
becomes unable to transmit video signals and may cause a black screen.
6~7
► A black screen does not indicate camera breakage; it resets itself and
starts displaying video again once its internal temperature reaches -20º or
higher.
6~7
► The motor may malfunction at temperatures lower than -20º ; please turn
on the camera in Standby mode instead of [Initialize].
6~7
► When the camera's internal temperature is between -10º to -20º, the
motor may malfunction, limiting the use of the Sequence and Turbo
commands.
6~7
► Once the internal temperature reaches -10º or higher, all Sequence modes
become reactivated normally.
6~7
► Please make sure to "Clear" the message from the screen.
6~7
► Such symptoms may occur if the camera's temperature increases from
-20º or lower to -20º or higher.
6~7
"Auto Refresh(Wait)" appears
and the camera reboots.
► Such symptoms may occur if the camera's temperature increases from
-10º or lower to -10º or higher to prevent the malfunction of motor.
6~7
“Please Check Heater System”
appears.
► The heater may malfunction. Turn off the camera and call where you
bought.
6~7
I can’t see the screen.
(The screen is black.)
The camera stops in the Initialize
mode and won’t proceed to the
next mode.
I can use the controller, but I
can’t activate the Sequence
command.
I can't get rid of this message
from the screen: “ Fan life
Expired. Replace the Fans.”
The camera suddenly resets
itself while displaying the black
screen.
Check the Power cord’s by periods
y The Power cord’s coating has
been damaged.
y The power cord is hot to touch
when the product is in operation.
y The power cord gets hot after
being folded or pulled on.
88_ troubleshooting
Continuing to use the product when its power cord is damaged constitutes an
electrical and fire hazard. The power plug must be removed from the outlet
immediately, and a qualified service personnel or your system provider should be
contacted for assistance.
-
product specifications
PRODUCT SPECIFICATIONS (SCP-2XXX SERIES)
Model
SCP-2370TH
NTSC : 811(H) x 508(V)
● PRODUCT SPECIFICATIONS
Total Pixels
PAL : 795(H) x 596(V)
NTSC : 768(H) x 494(V)
Effective Pixels
PAL :752(H) x 582(V)
Scanning System
2:1 Interlace
Internal
Internal / Line Lock
NTSC : H : 15.734kHz / V : 59.94Hz
Frequency
PAL : H : 15.625KHz / V : 50Hz
Horizontal Resolution
Min. Illumination
SCP-2370/2330/2270
1/4” Super HAD CCD II
Image Device
Synchronization
SCP-2370H/2270H/2330H
Color : 600TV lines / BW : 700TV lines
COLOR : 0.2 Lux (50 IRE @ F1.6 ), 0.0004 Lux (50IRE, Color, Sens-up 512x )
B/W : 0.02 Lux (50 IRE @ F1.6 ), 0.00004 Lux (50IRE, B/W, Sens-up 512x )
S / N Ratio
52 dB (AGC off, Weight On)
Video Output
CVBS : 1.0 Vp-p / 75Ω conposite
Focal Length
(Zoom Ratio)
3.5~129.5mm (37x) / 3.5~115.5mm (33x) / 3.5~94.5mm (27x)
Max. Aperture Ratio
1:1.6 (Wide) ~ 3.9 (Tele) (37x)/1:1.6 (Wide) ~ 3.6 (Tele) (33x)/1:1.6 (Wide) ~ 2.9 (Tele) (27x)
Angular Field of View
H : 55.5°(Wide) ~ 1.59°(Tele) / V : 42.5°(Wide) ~ 1.19°(Tele) (37x)
H : 55.5°(Wide) ~ 1.77°(Tele) / V : 42.5°(Wide) ~ 1.33°(Tele) (33x)
H : 55.5°(Wide) ~ 2.24°(Tele) / V : 42.5°(Wide) ~ 1.79°(Tele) (27x)
Min. Object Distance
1800mm
Focus Control
AUTO / MANUAL / ONE SHOT
Zoom Movement Speed
2.5sec (37x)/2.2sec (33x)/1.8sec (27x)
Pan Range
360° Endless
Pan Speed
Preset : 600°/sec / Manual : 0.024°/sec ~ 120°/sec
Tilt Range
-5° ~ 185°
Tilt Speed
Preset : 600°/sec / Manual : 0.024°/sec ~ 120°/sec
Preset
255
Preset Accuracy
Auto Tracking
OSD
Camera Title
±0.1°
Built-in
-
NTSC: ENGLISH, FRENCH, SPANISH, PORTUGUES, KOREAN, JAPANESE, TAIWANESE
PAL: ENGLISH, CHINESE, FRENCH, GERMAN, SPANISH, ITALIAN, PORTUGUES, POLISH, RUSIAN, CZECH,
TURKISH
Off / On (Displayed 12 Characters)
English - 89
product specifications
Model
SCP-2370TH
SCP-2370H/2270H/2330H
Day & Night
Auto (ICR) / Color / B/W
Back Light
BLC / HLC / Off
Contrast Enhancement
SSDR (Off/On)
Digital Noise
Reduction
SSNR III (Off/On)
Digital Image
Stabilization
Off/On
Motion Detection
Off/On
Privacy Masking
Off/On (8 programmable zones)
Sens-up
2x ~ 512x
Gain Control
Off/Low/Medium/High/Manual
White Balance
ATW / ATW (IN) / ATW (OUT) / Manual / AWC
NTSC :1/60~1/120,000sec
Electronic Shutter
Speed
PAL : 1/50~1/120,000sec
Digital Zoom
Off/On (2x ~ 16x)
Digital Flip
Off/On
Schedule
Day/Time
Alarm
8 In 3 Out
Communication
Protocol
SCP-2370/2330/2270
RS-485, Coaxial Control
Coax : Pelco-C ( Coaxitron )
RS-485: Auto Detected, SAMSUNG-T, SAMSUNG-E, Pelco(D/P), Panasonic, Vicon,Honeywell,AD,GE,BOSCH
Operating Temperature
/ Humidity
Ingress Protection
-50°C ~ +50°C / Less than 90% RH
-10°C~+50°C / 20~80% RH
IP66
-
Input Voltage
Power Consumption
24V AC ±10%
Max. 15W / 60W (Fan & Heater)
Max. 15W
Color / Material
Ivory, Aluminum, Plastic ( Dome Cover : Clear )
Ivory, Plastic (Dome Cover :
Clear)
Dimension (Φ×H)
Φ248 x 316.5mm
Φ155 x 243.4mm
4.5 Kg
2 Kg
Weight
Ú The specification for this product may change without prior notice for product improvement.
90_ product specifications
PRODUCT SPECIFICATIONS (SCP-3370 SERIES)
Model
SCP-3370TH
Image Device
PAL : 795(H) x 596(V)
NTSC : 768(H) x 494(V)
PAL :752(H) x 582(V)
Scanning System
2:1 Interlace
Internal
Internal / Line Lock
NTSC : H : 15.734kHz / V : 59.94Hz
Frequency
PAL : H : 15.625KHz / V : 50Hz
Horizontal Resolution
Color : 600TV lines / BW : 700TV lines
COLOR : 0.7 Lux (50 IRE @ F1.6 ), 0.001 Lux (50IRE, Color, Sens-up 512x )
B/W : 0.07 Lux (50 IRE @ F1.6 ), 0.0001 Lux (50IRE, B/W, Sens-up 512x )
S / N Ratio
52 dB (AGC off, Weight On)
Video Output
CVBS : 1.0 Vp-p / 75Ω conposite
Focal Length
(Zoom Ratio)
3.5~129.5mm
Max. Aperture Ratio
1:1.6 (Wide) ~ 3.9 (Tele)
Angular Field of View
H : 55.5°(Wide) ~ 1.59°(Tele) / V : 42.5°(Wide) ~ 1.19°(Tele)
Min. Object Distance
1800mm
Focus Control
AUTO / MANUAL / ONE SHOT
Zoom Movement Speed
2.8 sec
Pan Range
360° Endless
Pan Speed
Preset : 600°/sec / Manual : 0.024°/sec ~ 120°/sec
Tilt Range
-5° ~ 185°
Tilt Speed
Preset : 600°/sec / Manual : 0.024°/sec ~ 120°/sec
Preset
255
Preset Accuracy
Auto Tracking
OSD
● PRODUCT SPECIFICATIONS
NTSC : 811(H) x 508(V)
Effective Pixels
Min. Illumination
SCP-3370
EX-view HAD CCD
Total Pixels
Synchronization
SCP-3370H
±0.1°
Built-in
-
NTSC: ENGLISH, FRENCH, SPANISH, PORTUGUES, KOREAN, JAPANESE, TAIWANESE
PAL: ENGLISH, CHINESE, FRENCH, GERMAN, SPANISH, ITALIAN, PORTUGUES, POLISH, RUSIAN, CZECH,
TURKISH
Camera Title
Off / On (Displayed 12 Characters)
Day & Night
Auto (ICR) / Color / B/W
Back Light
BLC / HLC / Off
English - 91
product specifications
Model
SCP-3370TH
SCP-3370H
WDR
Low / Medium / High
Contrast Enhancement
SSDR (Off/On)
Digital Noise
Reduction
SSNR III (Off/On)
Digital Image
Stabilization
Off/On
Motion Detection
Off/On
Privacy Masking
Off/On (8 programmable zones)
Sens-up
2x ~ 512x
Gain Control
Off/Low/Medium/High/Manual
White Balance
ATW / ATW (IN) / ATW (OUT) / Manual / AWC
NTSC :1/60~1/120,000sec
Electronic Shutter
Speed
PAL : 1/50~1/120,000sec
Digital Zoom
Off/On (2x ~ 16x)
Digital Flip
Off/On
VPS
Off/On
Intelligent Video
Off / Detection / Tracking / Fixed/Moved
PIP
Off/On
Schedule
Day/Time
Alarm
8 In 3 Out
Communication
Protocol
SCP-3370
RS-485, Coaxial Control
Coax : Pelco-C ( Coaxitron )
RS-485: Auto Detected, SAMSUNG-T, SAMSUNG-E, Pelco(D/P), Panasonic, Vicon, Honeywell, AD,
GE, BOSCH
Operating Temperature
/ Humidity
Ingress Protection
-50°C ~ +50°C / Less than 90% RH
-10°C~+50°C / 20~80% RH
IP66
-
Input Voltage
Power Consumption
24V AC ±10%
Max. 15W / 60W (Fan & Heater)
Max. 15W
Color / Material
Ivory, Aluminum, Plastic ( Dome Cover : Clear )
Ivory, Plastic (Dome Cover : Clear)
Dimension (Φ×H)
Φ248 x 316.5mm
Φ155 x 243.4mm
4.5 Kg
2 Kg
Weight
Ú The specification for this product may change without prior notice for product improvement.
92_ product specifications
DIMENSIONS
215.7
243.4
● PRODUCT SPECIFICATIONS
27.7
❖ Indoor Model
R75
Ø155
❖ Environmental Model
Ø148
316.5
146.5
Ø248
Ø244
Ø162
English - 93
MEMO
MEMO
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300, FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungsecurity.com
P/NO. : PT01-000127B