Sharp PN-S525 Instruction manual

ENGLISH
ESPAÑOL
РУССКИЙ
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
Փ⫼䇈ᯢк
FRANÇAIS
LCD MONITOR
LCD FARBMONITOR
MONITEUR LCD
MONITOR LCD
ЖК МОНИТОР
⎆᱊ᰒ⼎఼
DEUTSCH
PN-S525
∝䇁
ENGLISH ...... E1
DEUTSCH ..... D1
FRANÇAIS .... F1
ESPAÑOL .... S1
РУССКИЙ ..... Р1
∝䇁 ............... C1
(.‫ ﺍﳌﺮﻓﻘﺔ‬CD-ROM ‫) ﺍﻟﺪﻟﻴﻞ ﺑﺎﻟﻠﻐﺔ ﺍﻟﻌﺮﺑﻴﺔ ﻳﻮﺟﺪ ﰲ ﺃﺳﻄﻮﺍﻧﺔ‬
IMPORTANT:
To aid reporting in case of loss or theft, please record the
product’s model and serial numbers in the space provided.
The numbers are located in the rear of the product.
Model No.:
Serial No.:
U.S.A. ONLY
FOR CUSTOMERS IN U.K.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW:
Earth
BLUE:
Neutral
BROWN:
Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
•The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth or coloured green or green-and-yellow.
•The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
•The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician.
“WARNING: THIS APPARATUS MUST BE EARTHED.”
Authorised representative responsible for the European Union Community Market
Autorisierter Repräsentant in der Europäischen Union
Représentant autorisé pour le marché de la communauté européenne
Representante autorizado responsable del mercado comunitario de la Unión Europea
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
LCD MONITOR
ENGLISH
PN-S525
ENGLISH
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
CAUTION: The AC outlet shall be installed near the equipment and shall be easily accessible.
CAUTION: Use the supplied power cord as it is.
This product utilizes fluorescent tubes containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling
information, please contact your local authorities.
1
E
IMPORTANT INFORMATION (Continued)
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of
these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance:
www.eiae.org, the lamp recycling organization: www.lamprecycle.org or Sharp at 1-800-BE-SHARP
(For U.S.A. Only)
U.S.A. ONLY
Attention: Your product is marked with this symbol. It means that used electrical and electronic products
should not be mixed with general household waste. There is a separate collection system for these products.
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dustbin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper
treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used electrical and
electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take
back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand
according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and
recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due
to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the
costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection
facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
E
2
IMPORTANT INFORMATION (Continued)
ENGLISH
The battery supplied with this product contains traces of Lead.
For EU:
The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation. Please contact your local authority for details on the collection and recycling
schemes.
For Switzerland:
The used battery is to be returned to the selling point.
For other non-EU countries:
Please contact your local authority for correct method of disposal of the used battery.
DEAR SHARP CUSTOMER
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2.Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5.Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners.
6.Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9.Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10.The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13.Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to perform servicing.
3
E
SAFETY PRECAUTIONS (Continued)
14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified
technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15.Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock and/or other danger.
16. Safety checks — Upon completion of service or repair work, request the service technician to
perform safety checks to ensure that the product is in proper operating condition.
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18.Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
• Use the specified batteries only.
• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the
compartment.
• Do not mix old and new batteries.
• Do not mix batteries of different types. Voltage specifications of batteries of the same shape may vary.
• Replace an exhausted battery with a new one promptly.
• If you will not use the remote control for a long time, remove the batteries.
• If leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your
eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your
clothing may cause a skin irritation or damage your eye.
20.Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate counter measures.
E
4
TIPS AND SAFETY INSTRUCTIONS
- Do not display a still picture for a long period, as this could
cause a residual image.
- Never rub or tap the monitor with hard objects.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- This monitor and its accessories may be upgraded without
advance notice.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam, as this could lead to fire.
- Ensure that the monitor does not come into contact with
water or other fluids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to fire or
electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
The Power Cord
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in fire or electric shock.
- Use only the power cord supplied with the monitor.
- Insert the power plug directly into the AC outlet.
Adding an extension cord may lead to fire as a result of
overheating.
ENGLISH
- The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
Initialization
- This monitor can remember e-mail addresses and other data.
Before transferring or disposing of this monitor, initialize all
settings by executing ALL RESET 1. (See Operation guide.)
Executing ALL RESET 2 will not reset e-mail addresses and
similar data.
Manual Scope
- Microsoft, Windows and Internet Explorer are registered
trademarks of Microsoft Corporation.
- HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of fire.
- Adobe, Acrobat, and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
- Images cannot be rotated on this monitor.
When using in vertical orientation, you will need to prepare
appropriately orientated content in advance.
- This product comes with RICOH Bitmap Fonts produced and
sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or
registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by
way of example.
- Illustrations in this manual may not exactly represent the
actual product or display.
- This manual assumes use in horizontal orientation, except
where specifically noted.
Fluorescent Tubes
● The fluorescent tubes in this product have a limited lifetime.
* If the screen gets dark, flashes, or does not turn on,
change the fluorescent tubes with new exclusive ones.
* For more information, please contact your product dealer.
● Because of the property of fluorescent tubes, the screen
may flash during the initial period of use. If this happens,
please turn off the main power switch of the monitor and
turn on again after at least 5 seconds to confirm operation.
5
E
Contents
IMPORTANT INFORMATION.............................................1
DEAR SHARP CUSTOMER...............................................3
SAFETY PRECAUTIONS...................................................3
TIPS AND SAFETY INSTRUCTIONS................................5
Supplied Accessories.......................................................7
Part Names........................................................................7
How to Install the Monitor................................................9
Mounting precautions....................................................9
Connecting Peripheral Equipment................................10
Connection with a PC..................................................10
Connection with AV equipment...................................10
Other terminals............................................................ 11
Connecting external speakers..................................... 11
Connecting multiple monitors...................................... 11
Connecting the Power Cord..........................................12
Mounting the Temporary Stands...................................12
Binding Cables................................................................13
Preparing the Remote Control Unit...............................13
Installing the batteries.................................................13
Remote control operation range..................................13
Turning Power On/Off.....................................................14
Turning on the main power.........................................14
Turning power on/off...................................................14
Disabling power on/off operations...............................14
Troubleshooting..............................................................15
Specifications.................................................................16
This manual contains instructions regarding connection and installation.
For instructions regarding operation, settings, and similar details, refer to the Operation Guide (PNS525_guide_English.pdf)
in the “manual” folder on the included CD-ROM.
Adobe Reader is required in order to view the Operation Guide.
E
6
Supplied Accessories
� Liquid Crystal Display: 1
� Power cord: 1
� R-6 battery (“AA” size): 2
� CD-ROM (Utility Disk for Windows): 1
� Operation manual: 1
� Blank sticker: 1
Place a blank sticker onto the SHARP logo to cover the logo.
� Vertical logo
sticker: 2
� Remote control
unit: 1
� Temporary stand: 2
� Cable clamp: 2
ENGLISH
If any component should be missing, please contact your dealer.
� Power cord
clamp: 1
INPUT
* Sharp Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
Part Names
nFront view
1
1. LCD panel
2. Remote control sensor (See page 13.)
3. Input switch (See Operation guide.)
4. Power switch (See page 14.)
5. Power LED (See page 14.)
INPUT
TIPS
2
3
4 5
• Use a pointed object such as a pen tip to press the
switches at the front of the monitor.
7
E
Part Names
nRear view
19
18
1
3
4
5
6
7
9 1011
8
2
12 13
14 1516 17
1. Main power switch (See page 14.)
2. AC input terminal (See page 12.)
3. PC/AV output terminal (DVI-D) (See page 11.)
4. PC1 input terminal (DVI-D) (See page 10.)
AV1 input terminal (DVI-D) (See page 10.)
5. PC2 input terminal (HDMI) (See page 10.)
AV2 input terminal (HDMI) (See page 10.)
6. PC3 input terminal (Mini D-sub 15 pin) (See page 10.)
7. PC4 input terminals (BNC) (See page 10.)
8. AV3 input terminals (BNC) (See page 10.)
9. AV5 input terminal (BNC) (See page 10.)
10. AV4 input terminal (S) (See page 10.)
11. LAN terminal (See page 11.)
12. RS-232C output terminal (D-sub 9 pin) (See page 11.)
13. RS-232C input terminal (D-sub 9 pin) (See page 11.)
14. PC/AV audio output terminals (See page 11.)
15. AV audio input terminals (See page 10.)
16. PC audio input terminal (See page 10.)
17. External speaker terminals (See page 11.)
18. Handles
19. Vents
nRemote control unit
1
2
7
3
8
4
5
6
E
8
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
Signal transmitter
POWER button (See page 14.)
MUTE button (See Operation guide.)
VOL +/- buttons (See Operation guide.)
BRIGHT +/- buttons (See Operation guide.)
Cursor control ( /
/
/ ) buttons
DISPLAY button (See Operation guide.)
MODE button (See Operation guide.)
INPUT button (See Operation guide.)
MENU button (See Operation guide.)
SIZE button (See Operation guide.)
How to Install the Monitor
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• When installing, removing or moving the monitor, ensure
that this is carried out by at least 2 people.
• A stand and mounting bracket compliant with VESA
specifications is required. Do not use any screw holes other
than VESA holes for installation.
• When moving the monitor, be sure to hold it with the
handles both on the rear and the unit bottom. Do not hold
the LCD panel. This may cause product damage, failure, or
injury.
• Install the monitor with the surface perpendicular to a level
surface. If necessary, the monitor may be tilted up to 20
degrees.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• This monitor should be used at an ambient temperature
between 32°F (0°C) and 104°F (40°C). Provide
enough space around the monitor to prevent heat from
accumulating inside.
For the monitor in horizontal orientation
• If it is difficult to provide this much space for any reason
such as the installation of the monitor inside a housing, or
if the ambient temperature may be outside of the range
of 32°F (0°C) to 104°F (40°C), install a fan in the housing
or take other measures to keep the ambient temperature
within the required range.
• Adhere to the following when installing the monitor in the
vertical orientation. Failing to adhere to the following may
cause malfunctions.
- Install the monitor such that the power LED is located on
the downside.
- Set the MONITOR on the SETUP menu to PORTRAIT.
(See Operation guide.)
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• After mounting, it is recommended to take some measures
to prevent the monitor from falling down.
• Do not place the monitor on a device which generates heat.
• Use the supplied vertical logo sticker when you install the
monitor in vertical orientation.
ENGLISH
Mounting precautions
*
INPUT
Unit: inch [cm]
7-7/8 [20]
*
2
[5]
2
[5]
2 [5]
For the monitor in vertical orientation
Unit: inch [cm]
7-7/8 [20]
*
2
[5]
* Do not remove the factory-affixed sticker but affix the logo
sticker over it. Be careful not to cover the remote control
sensor or buttons.
• Be sure to use a stand or a wall-mount/ceiling bracket
designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall/
ceiling or pillar. Reinforced work might be necessary for
some materials such as plaster / thin plastic board / wood
before starting installation.
This monitor and bracket must be installed on a wall which
can endure at least 4 times or more the weight of the
monitor. Install by the most suitable method for the material
and the structure.
2
[5]
2 [5]
* The monitor can be installed close to a wall, etc.
However, the monitor emits heat during operation. Be
aware that heat emitted from the monitor may discolour
or alter the wall.
9
E
Connecting Peripheral Equipment
• Be sure to turn off the main power switch and disconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Be careful not to mix up the input terminal with the output
terminal when connecting cables. Mixing up the input and
output terminals may cause malfunctions and the other
problems.
Connection with AV equipment
Video input
Caution
PC1 input terminal
Audio input
PC3 input terminal
PC2 input terminal
V
H
R
G
B
PC4 input terminals
PC audio input terminal
• Use a commercially available signal cable (DVI-D 24 pin)
for the PC1 input terminal. Set DVI SELECT of INPUT
SELECT on the OPTION menu to PC1 DVI-D when using
the PC1 input terminal. (See Operation guide.)
• Use a commercially available HDMI cable (conforming to
the HDMI standard) for the PC2 input terminal. Set HDMI
SELECT of INPUT SELECT on the OPTION menu to PC2
HDMI when using the PC2 input terminal. In addition,
select the audio input terminal to be used in HDMI AUDIO
SELECT of INPUT SELECT on the OPTION menu. (See
Operation guide.) When DIGITAL is selected, connection to
the PC audio input terminal is unnecessary.
• Use a commercially available signal cable (Mini D-sub
15 pin) for the PC3 input terminal.
• Use a commercially available signal cable (BNC) for the
PC4 input terminals. Set BNC SELECT of INPUT SELECT
on the OPTION menu to PC4 RGB when using the PC4
input terminals. (See Operation guide.)
• Use a commercially available audio cable (mini stereo jack)
for the PC audio input terminal. Use an audio cable without
resistance.
TIPS
• Images may not be displayed properly depending on the
computer (graphics board) to be connected.
• A screen with 1920 x 1080 resolution may not be displayed
correctly on PC4. In this case, check the settings of your
computer (graphics board) to verify that input signals
conform to specifications of this monitor. (See page 17.)
• If there is a check box to disable EDID in display control
panel, check it when using PC4.
• Use the automatic screen adjustment when a PC screen is
displayed for the first time using PC3 or PC4, or when the
setting of the PC is changed. (See Operation guide.)
The screen is adjusted automatically when SELF ADJUST
in the OPTION menu is set to ON. (See Operation guide.)
E
10
AV2 input
terminal
AV4 input terminal
Audio input
Video input
Connection with a PC
AV1 input
terminal
Cr/Pr
Y
Cb/Pb
AV3 input
terminals
AV5 input terminal
AV audio input terminals
• Use a commercially available signal cable (DVI-D 24 pin)
for the AV1 input terminal. Set DVI SELECT of INPUT
SELECT on the OPTION menu to AV1 DVI-D when using
the AV1 input terminal. (See Operation guide.)
• Use a commercially available HDMI cable (conforming to
the HDMI standard) for the AV2 input terminal. Set HDMI
SELECT of INPUT SELECT on the OPTION menu to
AV2 HDMI when using the AV2 input terminal. In addition,
select the audio input terminal to be used in HDMI AUDIO
SELECT of INPUT SELECT on the OPTION menu. (See
Operation guide.) When DIGITAL is selected, connection to
the AV audio input terminal is unnecessary.
• Use a commercially available component cable (BNC)
for the AV3 input terminals. Set BNC SELECT of INPUT
SELECT on the OPTION menu to AV3 COMPONENT when
using the AV3 input terminals. (See Operation guide.)
• Use a commercially available S-video cable for the AV4
input terminal.
• Use a commercially available video cable (BNC) for the
AV5 input terminal.
• Use a commercially available audio cable (RCA) for the AV
audio input terminals.
• The AV1/AV2 input terminals are compatible with the video
signals below:
1920 x 1080p @ 50/59.94/60 Hz
1920 x 1080i @ 50/59.94/60 Hz
1280 x 720p @ 50/59.94/60 Hz
720 x 576p @ 50 Hz
720 x 480p @ 59.94/60 Hz
640 x 480p @ 59.94/60 Hz
• The AV2 input terminal is also compatible with the video
signals below:
1920
x1080p @ 24Hz
720(1440)x 576i @ 50Hz
720(1440)x 480i @ 59.94/60Hz
• The AV3 input terminals are compatible with the video
signals below:
1080p @50/60Hz, 1080i @50/60Hz, 720p @50/60Hz,
576p @50Hz, 576i @50Hz, 480p @60Hz, 480i @60Hz
Connecting Peripheral Equipment
Connecting multiple monitors
PC/AV audio output terminals
• Audio from the equipment connected to the AV audio input
terminals or PC audio input terminal is output. Connect to
the audio input terminals of the connected equipment using
a commercially available audio cable (RCA).
• The audio output varies depending on the input mode
selection. (See Operation guide.)
• The volume level can be adjusted using the volume
adjustment. (See Operation guide.)
• Selecting FIXED of “AUDIO OUTPUT” from the OPTION
menu fixes the volume of sound output from the audio
output terminals. (See Operation guide.)
• Audio signals output from the PC/AV audio output terminals
cannot be adjusted using the AUDIO menu.
You can connect multiple monitors (up to 5 monitors) in a
daisy chain by using the PC1/AV1 input terminals and PC/AV
output terminals of this monitor.
Connection example
First monitor
PC/AV output
terminal
PC/AV output terminals
Video signals from PC1 and AV1 can be output to external
device. Use this terminal when you connect multiple monitors
in a daisy chain via DVI cable (commercially available). (See
the description on the right.)
Outputting images encoded with HDCP requires an HDCPcompatible external device.
Images cannot be output in the following situations:
- In PC2/AV2 input mode
- When PIP SOURCE in the PIP/PbyP Menu is set to PC2
HDMI or AV2 HDMI
(1)
(2)
PC1/AV1 input terminals
To PC digital RGB output terminal
LAN terminal
You can control the monitor from a PC on a network by
connecting a commercially available LAN cable between this
terminal and a network. (See Operation guide.)
Be sure to use external speakers with an impedance of 6 Ω
and a rated input of at least 7 W.
Second monitor
Digital signal (DVI) cables
(commercially available)
RS-232C input/output terminals
You can control the monitor from a PC by connecting a
commercially available RS-232 straight cable between this
terminal and the PC. (See Operation guide.)
Connecting external speakers
ENGLISH
Other terminals
shows the signal flow
TIPS
• The length of the signal cables or surrounding environment
may affect the image quality.
• The screen may not display properly when using terminals
other than PC1/AV1 for the input mode. In this case, turn
off the power to all the monitors connected in a daisy chain
and then turn the power on again.
• When connecting monitors in a daisy chain set AUTO
INPUT CHANGE to OFF.
1. While pushing the tab, insert the tip of the cable.
2. Release the tab.
TIPS
• Be sure to connect the + and - terminals and the left and
right speakers properly.
• Avoid short circuiting the + and - terminals.
11
E
Connecting the Power Cord
Caution
• Do not use a power cord other than the one supplied with
the monitor.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the AC power outlet.
3
Main power switch
1
For power
outlet
2
AC input terminal
Power cord (Supplied)
Mounting the Temporary Stands
Caution
• The monitor is heavy. Make sure to handle the monitor with
at least 2 people.
• Please note that the temporary stands are for temporary
use only until the monitor is properly mounted.
Remove the screws from the monitor and mount the
temporary stand using the screws.
The temporary stand can be mounted at a position shown in
the illustration.
Temporary stand
Screws
Caution
• After detaching the temporary stand, be sure to re-mount
the removed screws on the monitor.
E
12
Binding Cables
ENGLISH
nAttaching the cable clamp
Cable clamp
positions
The cables connected to the terminals on the back of the
monitor can be neatly bundled using the supplied cable
clamps as shown in the illustration.
Insert the cable
clamp into a hole.
(any hole available)
Cable clamp
attachment
Cable clamp
Caution
• Verify the position for attaching a cable clamp in advance.
A cable clamp cannot be removed once it is attached.
nFastening the power cord
The power cord can be fastened using the supplied power
cord clamp. This will prevent the power cord from being
disconnected accidentally.
1. Attach the supplied power cord clamp to the power
cord, making sure the power cord clamp is circular holesidedown.
2. Insert the tip of the band into the hole for the power cord
clamp.
3. While holding the tail of the band, slide the fastened part
toward the AC input terminal.
1
2
Fastened
part
Band
Power cord
clamp
3
Hole for
the power
cord clamp
Preparing the Remote Control Unit
Installing the batteries
Remote control operation range
1. Press the cover gently and slide it in the direction of the
arrow.
The operation range of the remote control unit is approx. 16.4
feet (5 m) at an angle of approx 10° from the center to the
top/bottom/right/left of the remote control sensor.
Remote control sensor
16.4 feet (5 m)
2. See the instructions in the compartment and put in the
supplied batteries (R-6 (“AA” size) x 2) with their plus (+)
and minus (-) sides oriented correctly.
3. Close the cover.
TIPS
• When the batteries become exhausted replace them
with new (commercially available) batteries earlier than
specified.
• The supplied batteries (R-6 (“AA” size) x 2) may become
exhausted quickly depending on how they are stored.
• If you will not use the remote control for a long time,
remove the batteries.
• Use manganese or alkaline batteries only.
10°
.4
16
t (5
fee
m)
16.4 feet (5 m)
10°
TIPS
• Do not expose the remote control unit to shock by dropping
or stepping on it. This could lead to a malfunction.
• Do not expose the remote control unit to liquids, and do not
place it in an area with high humidity.
• The remote control unit may not work properly if the remote
control sensor is under direct sunlight or strong lighting.
• Objects between the remote control unit and the remote
control sensor may prevent proper operation.
• Replace the batteries when they run low as this may
shorten the remote control’s operation range.
• If a fluorescent light is illuminated near the remote control
unit, it may interfere with proper operation.
• Do not use it with the remote control of other equipment
such as air conditioner, stereo components, etc.
13
E
Turning Power On/Off
Caution
TIPS
• Turn on the monitor first before turning on the PC or
playback device.
Turning on the main power
• If the monitor is in the input signal standby mode and you
press the POWER button on the remote control unit, the
monitor enters standby mode.
• You can turn on/off the monitor by pressing the power
switch of the monitor.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
• When STANDBY MODE is set to STANDARD, startup time
can be reduced. Note, however that, more power will be
consumed in standby mode.
nDate/time setting
• If the time has yet to be set when the monitor is first turned
on, the date/time setting screen appears. Set the date and
time.
Main power switch
DATE/TIME SETTING
/
SET
When the main power switch is off, the monitor cannot be
turned on using the POWER button on the remote control unit.
20
/
08 /
:
01 /
01
:
00
:
00
CANCEL
Turning power on/off
Press the POWER button to turn the power ON/OFF.
OK···[MENU]
1. Press
,
,
or
to select the date and
or
to change the numerical
time, and press
values.
2. Select SET and then press MENU .
INPUT
Power LED
Status of a power LED
Green lighting
Orange lighting
Status of the monitor
Power “On”
Power “Off” (Standby mode)
Green flashing
Input signal standby mode
(input using a PC)
Caution
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
A short interval may result in a malfunction.
E
14
• Be sure to set the date and time.
• The date/time setting screen will close automatically if no
operation is performed for about 15 seconds. The date
and time can be set using DATE/TIME SETTING from
the OPTION menu when the date/time setting screen
disappears.
TIPS
• Set the date in “Year/Month/Day” order.
• Set the time on a 24-hour basis.
• The clock stops after the power-off status continues for
approximately 1 week.* The date/time setting screen
appears at power-on. Be sure to set the date and time.
(* This is a guide. The power-off status that stops the clock
depends on the status of the monitor.)
Disabling power on/off operations
Power on/power off operations can be disabled in order to
protect the monitor from an accidental power off. Set the
ADJUSTMENT LOCK in FUNCTION menu to “2”. (See
Operation guide.)
Troubleshooting
There is no picture or sound.
• Is the power cord disconnected? (See page 12.)
• Is the main power switch set to “OFF”? (See page 14.)
• Is the monitor in standby mode (the power LED illuminating
in orange)? (See page 14.)
• Make sure correct input mode is selected. (See Operation
guide.)
• If any external equipment is connected, make sure the
equipment is operating (playing back).
Remote control does not work.
• Are the batteries inserted with polarity (+,-) aligned? (See
page 13.)
• Are the batteries exhausted? (See page 13.)
• Point the remote control unit toward the monitor’s remote
control sensor. (See page 13.)
• Is the menu display hidden or is operation disabled? (See
Operation guide.)
Sound from left and right speakers is reversed.
Sound is heard from only one side.
• Are audio cables connected properly? (See pages 10 and
11.)
• Make sure audio cables for external speakers are
connected properly: left and right cables may be reversed
or one of the two cables may not be connected. (See page
11.)
• Check the setting of BALANCE for AUDIO menu. (See
Operation guide.)
There is a picture but no sound.
• Is the sound muted?
• Make sure the volume is not set to minimum.
• Is the PC audio cable (commercially available) connected?
• Are audio cables connected properly?
• Is the audio signal input properly to the audio input terminal
corresponding to the selected video input terminal?
• When PC2 or AV2 is used, is the setting of HDMI AUDIO
SELECT correct? (See Operation guide.)
Unstable video.
• The signal may be incompatible.
• Try the automatic screen adjustment when the PC3 input
terminal or PC4 input terminals is used.
PC1 or AV1 does not appear properly.
• Is the setting of DVI SELECT correct? (See Operation
guide.)
• Is the input signal compatible with this monitor? (See pages
10 and 17.)
• Turn off the power to the connected equipment and then
turn the power on again.
• If the monitors are connected in a daisy chain, turn off the
power to all the monitors connected in a daisy chain and
then turn the power on again.
PC2 or AV2 does not appear properly.
• Is the setting of HDMI SELECT correct? (See Operation
guide.)
• Is the HDMI cable HDMI standard compliant? The monitor
will not work with cables that are not standard compliant.
• Is the input signal compatible with this monitor? (See pages
10 and 17.)
PC4 or AV3 does not appear properly.
• Is the setting of BNC SELECT correct? (See Operation guide.)
• Is the input signal compatible with this monitor? (See pages
10 and 17.)
Control buttons do not work.
There is no picture.
• Some kind of load noises from outside might interfere with
normal operation. Turn off the power and turn it on after
waiting at least 5 seconds, and then check the operation.
ENGLISH
Before calling for repair services, make sure following checks
for possible remedies to the encountered symptoms.
The input mode changes automatically.
• When the AUTO INPUT CHANGE is ON and no signal
is present in a selected input mode, the AUTO INPUT
CHANGE automatically changes the selected mode to a
mode where a video signal is present.
The input mode may change in the following cases:
-When a computer is in standby mode.
-When video play is stopped with a playback device.
Power LED flashes red.
“STATUS [xxxx]” appears in the corner of the screen.
• Hardware has a problem. Turn off the monitor and request
repair from your SHARP dealer.
(When STATUS ALERT is set to OSD & LED. This varies
depending on the setting.)
When “AUTO DIMMING” is displayed.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight automatically
decreases in order to prevent a further temperature rise. If
you attempt to use
to adjust the brightness while
the monitor is in this state, “AUTO DIMMING” is displayed
and you cannot change the brightness.
• Remove the cause of the excessive temperature rise.
The monitor sometimes makes a cracking sound.
• You may hear cracking sound from the monitor. This
happens when the cabinet slightly expands and contracts
according to change in temperature. This does not affect
the monitor’s performance.
The Power LED is flashing in red and green alternately.
When “TEMPERATURE” is displayed in the corner of the
screen.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperaturerelated problems. When this occurs, “TEMPERATURE” is
displayed on the screen and the Power LED flashes red
and green alternately. (When TEMPERATURE ALERT is
set to OSD & LED. This varies depending on the setting.)
• If the internal temperature rises further, the monitor
automatically enters standby mode. (The Power LED
continues flashing red and green alternately.)
• Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated. (See page 9.)
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask Sharp dealer about removing internal dust.
15
E
Specifications
nProduct Specifications
Model
LCD element
Max. resolution
(pixels)
Max. colors
Pixel pitch
Viewing angle
Screen active area inch (mm)
Computer input signal
Sync signal
PN-S525
52" wide (132.2 cm diagonal) ASV low-reflection black TFT LCD
1920 x 1080
16.77 M colors (8 bits/color)
0.600 mm (H) x 0.600 mm (V)
176° right/left/up/down (contrast ratio ≥ 10)
45-3/8 x 25-1/2 (1152.0 x 648.0)
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω]
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)
Video color system
PAL, PAL-60, SECAM, NTSC (3.58 MHz), NTSC (4.43 MHz)
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
PC/AV
Digital
DVI-D 24 pin (HDCP compatible) x 1
HDMI x 1
PC
Analog
Mini D-sub 15 pin, 3 rows x 1
BNC *1*2 x 1
Audio
3.5 mm mini stereo jack x 1
AV
Composite video
BNC x 1
S-video
x1
Component
BNC (Y, Cb/Pb, Cr/Pr)*1 x 1
Audio
RCA pin (L/R) x 1
Serial (RS-232C)
D-sub 9 pin x 1
Output terminals
PC/AV
Digital
DVI-D 24 pin x 1
Audio
RCA pin (L/R) x 1
Serial (RS-232C)
D-sub 9 pin x 1
Speaker
7 W + 7 W [6 Ω]
LAN terminal
10 BASE-T/100 BASE-TX
Power requirement
AC 100 V - 240 V, 50/60 Hz
Operating temperature
32°F to 104°F (0°C to 40°C)
Operating humidity
20% to 80% (no condensation)
Power consumption
275 W (Input signal waiting mode: 12 W *3, Standby mode: 2.0 W *4)
Dimensions
inch (mm) Approx. 49-3/8 x 5-7/8 x 29-3/16 (1,254 x 149 x 742) (excluding protrusions)
Weight
lbs. (kg) Approx. 86.0 (39) (excluding the temporary stand)
*1
*2
*3
*4
Cannot be used simultaneously.
Does not support plug and play.
When AUTO INPUT CHANGE is set to OFF.
When STANDBY MODE is set to LOW POWER, LAN and SCHEDULE are not used. When STANDBY MODE is set to STANDARD, 12W.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
nPower management
This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in
order for the monitor’s power management function to work.
DPMS: Display Power Management Signaling
DPMS
ON STATE
STANDBY
SUSPEND
OFF STATE
E
16
Power
Screen consumption
Hsync
Display
No
display
275 W
12 W*
DMPM: Digital Monitor Power Management
Screen
Power
consumption
Monitor ON
Display
275 W
Active OFF
No display
12 W*
Vsync
DMPM
Yes
Yes
No
Yes
Yes
No
No
No
* When AUTO INPUT CHANGE is set to OFF.
Specifications
Note that the values shown are approximate values.
34-3/4 [882]
Unit: inch [mm]
VESA holes
7-7/8
[200]
7-7/8
[200]
7-7/8 [200]
10-11/16
[271]
49-3/8 [1254]
3-5/8
[92]
Opening width (45-9/16 [1157])
2-5/8 [66]
7-7/8
[200]
Opening height
(25-11/16 [653])
29-3/16 [742]
3-3/4 [95]
5-7/8 [149]
ENGLISH
nDimensional Drawings
When mounting the monitor, be sure to use a wall-mount/ceiling-mount bracket they comply with the VESA-compatible
mounting method. SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose holding may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use the bracket which applied UL1678 standard, and which can endure at least 4 times or more the
weight of the monitor.
nCompatible signal timing (PC)
Screen resolution
VESA
640 × 480
800 × 600
848 × 480
1024 × 768
1152 × 864
1280 × 768
1280 × 960
1280 × 1024
Wide
US TEXT
Sun
1360 × 768
1400 × 1050
1600 × 1200*1
1680 × 1050
1920 × 1200*1
1280 × 720
1920 × 1080
720 × 400
1024 × 768
1152 × 900
1280 × 1024
1600 × 1000
Hsync
Vsync
Dot frequency
31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
31.0kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
47.8kHz
60.3kHz
60.0kHz
64.0kHz
80.0kHz
47.7kHz
65.3kHz
75.0kHz
65.3kHz
74.0kHz
44.7kHz
66.3kHz
67.5kHz
31.5kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz
68.6kHz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
75Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
70Hz
60Hz
66Hz
70Hz
66Hz
76.2Hz
67.2Hz
76Hz
66Hz
25.175MHz
31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
33.75MHz
65.0MHz
75.0MHz
78.75MHz
108.0MHz
79.5MHz
102.25MHz
108.0MHz
108.0MHz
135.0MHz
85.5MHz
121.75MHz
162.0MHz
146.25MHz
154.0MHz
74.4MHz
148.5MHz
148.5MHz
28.3MHz
64.13MHz
70.4MHz
74.25MHz
94.88MHz
108.23MHz
117.01MHz
134.99MHz
135.76MHz
Digital
Analog(PC3/PC4)
DVI(PC1)
HDMI(PC2)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1 Displays a reduced image.
* All are compliant only with non-interlaced.
* Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.
* The frequency values for the Sun are reference values.
17
E
Specifications
nDDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect
plug-and-play monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
nPC1/AV1 input
(DVI-D24 pin)
No.
terminal pins
Function
No.
Function
No.
Function
TMDS data 2-
13
N.C.
1
TMDS data 2+
11
TMDS clock shield
2
TMDS data 2+
14
+5V
2
TMDS data 2 shield
12
TMDS clock-
3
TMDS data 2/4 shield
15
GND
3
TMDS data 2-
13
CEC
4
N.C.
16
Hot-plug detection
4
TMDS data 1+
14
N.C.
5
N.C.
17
TMDS data 0-
5
TMDS data 1 shield
15
SCL
6
DDC clock
18
TMDS data 0+
6
TMDS data 1-
16
SDA
7
DDC data
19
TMDS data 0/5 shield
7
TMDS data 0+
17
DDC/CEC GND
8
N.C.
20
N.C.
8
TMDS data 0 shield
18
+5V
9
TMDS data 1-
21
N.C.
9
TMDS data 0-
19
Hot-plug detection
10
TMDS data 1+
22
TMDS clock shield
10
TMDS clock+
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
No.
pins
Function
nRS-232C input
(D-sub 9 pin)
No.
Function
No.
terminal pins
Function
No.
Function
1
Red video signal input
9
+5V
1
N.C.
6
N.C.
2
Green video signal input
10
GND
2
Transmitted data
7
N.C.
3
Blue video signal input
11
N.C.
3
Received data
8
N.C.
4
N.C.
12
DDC data
4
N.C.
9
N.C.
5
GND
13
Hsync signal input
5
GND
6
GND for red video signal
14
Vsync signal input
7
GND for green video signal 15
8
GND for blue video signal
nPC/AV output
(DVI-D24 pin)
No.
18
Function
pins
1
nPC3 input terminal
(Mini D-sub 15 pin)
E
No.
nPC2/AV2 input terminal
(HDMITM Connector)
DDC clock
terminal pins
Function
No.
nRS-232C output
(D-sub 9 pin)
Function
No.
Function
terminal pins
No.
Function
1
TMDS data 2-
13
N.C.
1
N.C.
6
N.C.
2
TMDS data 2+
14
+5V
2
Received data
7
N.C.
3
TMDS data 2/4 shield
15
GND
3
Transmitted data
8
N.C.
4
N.C.
16
Hot-plug detection
4
N.C.
9
N.C.
5
N.C.
17
TMDS data 0-
5
GND
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
N.C.
20
N.C.
9
TMDS data 1-
21
N.C.
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-