Whirlpool RM765PXA Specifications

A Note To You
2
Important Safety
h5tructions
3
Parts And Features
5
Using Your Oven
6
Usin The
Setf -El eaning Cycle
25
Carin For
Your 8 ven
29
tf Y?u Need
i%PM?E
32
Warranty
36
1-800-253-1301
Call us with questions or comments.
SELF-CLEANING
ELECTRIC BUILT-IN
LOWER OVEN
MODELS
NOTE: Use and care instructions for the upper
microwave oven are provided in a separate manual.
ia -sa
RM770PXA
RM765PXA
A Note To You
Thank
you for buying
a Whirlpool
appliance.
You have purchased a quality, worldclass home appliance. Years of engineering experience have gone
into its manufacturing. To ensure that you will enjoy many years of trouble-free operation, we have
developed this Use and Care Guide. It is full of valuable information on how to operate and maintain
your appliance properly and safely. Please read it carefully. Also, please complete and mail the Ownership Registration Card provided with your appliance. This will help us notify you about any new information on your appliance.
Your
safety
is important
to us.
This guide contains safety symbols and statements. Please pay special attention to these symbols and
follow any instructions given. Here is a brief explanation of the use of each symbol.
This symbol will help alert you to such dangers as
personal injury, burns, fire and electrical shock.
This symbol will help you avoid actions which
could cause product damage (scratches, dents,
etc.) and damage to your personal property.
Our Consumer
Assistance
Center
is toll-free,
24 hours a day.
number,
1-800-253-1301,
If you ever have a question concerning your appliance’s operation, or if you need service, first see “If
You Need Assistance Or Service” on page 32. If you need further help, feel free to call our Consumer
Assistance Center. When calling, you will need to know your appliance’s complete model number and
serial number. You can find this information on the model and serial number plate (see diagram on
page 5). For your convenience, we have included a handy place below for you to record these numbers,
the purchase date from the sales slip and your dealer’s name and telephone number. Keep this book
and the sales slip together in a safe place for future reference.
Model Number
Dealer Name
Serial Number
Dealer Phone
Purchase
2
Date
Important
Safety Instructions
General
l
l
l
l
l
l
l
Read all instructions before
using the oven.
Install or locate the oven only
in accordance with the provided Installation Instructions.
The oven must be installed by
a qualified installer. The oven
must be roperly connected to
electrica Psupply and grounded.
CAUTION: Do not store things
children mi ht want above the
oven. Chil cpren could be
burned or injured while climbing on it.
Do not leave children alone
or unattended in area where
the oven is in use. They should
never be allowed to sit or stand
on an part of the oven. They
could iI e burned or injured.
Do not operate the oven if
it is damaged or not working
properly.
Do not use the oven for
warming or heatin the room.
Persons could be %urned or
injured, or a fire could start.
Use the oven onl for its
intended use as J escribed in
this manual.
l
l
l
l
DO NOT TOUCH HEATING
ELEMENTS OR INTERIOR
SURFACES OF OVEN.
Heating elements may be hot
even though they are dark in
color. lntenor surfaces of an
oven become hot enough to
cause burns. During and after
use, do not touch, or let clothing or other flammable materials contact heatin elements or
interior surfaces 03 oven until
they have had sufficient time to
cool. Other surfaces of the
oven may become hot enough
to cause burns; such as, the
oven vent opening, the surface
near the vent opening, the oven
door and window.
Do not wear loose or hanging
arments when using the oven.
8 he could ignite if they touch a
hot i! eating element and you
could be burned.
Use only d potholders. Moist
or damp por holders on hot
surfaces ma result in burns
from steam. b 0 not let
potholder touch hot heating
elements. Do not use a towel or
bulky cloth for a potholder. It
could catch on fire.
Keep oven vents unobstructed.
continued
on next page
given off in the Self-Cleaning
cycle from fiberglass insulation
and food decomposition. Significant exposure to these substances can cause cancer or
reproductive harm. Exposure
can be minimized by venting
with a hood or open window
and wiping out excess food
shills briar to self-cleanina.
Do not heat unopened containers. They could explode. The
hot contents could cause
burns and container particles
could cause injury.
l Do not store flammable
materials on or near the oven. The
fumes can create an explosion
and/or fire hazard.
When using the oven
l
Always position oven rack(s) in
desired location while oven IS
cool. If a rack must be removed while oven is hot, do
not let potholder contact hot
heating element in oven.
l Use care when opening oven
door. Let hot air or steam
escape before removing or
replacing food.
Grease
l
l
l
l
Grease is flammable and
should be handled carefully.
Let fat cool before attemptrng
to handle it.
l
ing grease outside of pan can
be extinguished with baking
soda or, rf available, a multipurpose dry chemical or foamtype extinguisher.
Care and cleaning
l
Small amounts of formaldehyde and carbon monoxide are
l
l
Do not use oven cleaners. No
commercial oven cleaner or
oven liner rotective coating of
any kind s I! ould be used in or
around any part of the oven.
Before self-cleaning the oven.,
remove broiler an, broiler nd,
oven racks an B other utensl9 s.
Do not use your oven to clean
miscellaneous parts unless you
are instructed to do so in this
Use and Care Guide.
Do not clean door heat seal. It
is essential for a good seal.
Care should be taken not to
rub, damage or move the seal.
Clean only parts recommended
in this Use and Care Guide.
Do not repair or replace any
part of the oven unless specifically recommended in this
manual. All other servicing
should be referred to a qualified
technician.
Disconnect the electrical supply
before servicing the oven.
- SAVE THESE INSTRUCTIONS
4
-
Parts And Features
This section contains captioned illustrations of your appliance.
location and appearance of all parts and features.
Use them to become familiar with the
Upper microwave oven (see 8eparate upper microwave
oven use and care guide for more information)
Control panel
Lock lever
cover panel
Lower oven
vent Broil
-element
Model and
serial number
plate-
Lower
Bake
,ehlent
oven control
Manual oven
panel
Using Your Oven
In This
Section
Page
Page
................................................ 11
Positioning racka and pans ............................... 6
Bakindroasting
For beat air circulation ...................................... .7
Adjusting the oven temperature control ....... .12
Using aluminum foil for baking.. ...................... .7
The electronic oven control ............................... 6
Broiling .............................................................. 13
Broiling rack position chart ............................. 14
Setting the clock.. .............................................. .9
Broiling tips ....................................................... 14
Using the electronic Minute Timer ................... .9
Energy saving tips ............................................ 14
Using the Oft/Cancel pad ................................ .10
Using the electronic MEALTIMER” conbol ...15
Audible signals ................................................. 10
The oven vent ................................................... 24
To obtain the best cooking results possible, you must operate your oven properly. This section gives
you important information for efficient and safe use of your oven.
Positioning
racks
and pans
For baking/roasting
with one rack, place the
rack so the top of the food will be centered in the
oven.
Rack placement for specific foods:
Personal Injury Hazard
Always position oven rack(s) in desired
location before turning oven on. Be sure
the rack(s) is level.
l If rack(s) must be moved while oven is
hot, use potholders or oven mitts to
protect hands.
Failure to follow the above precautions may
resutt in personal injury.
l
I
FOOD
1 RACK
1 POSITION
Frozen pies, large roasts,
turkeys
Lowest level or
2nd level from
bottom
Cookies, biscuits, muffins,
cakes, nonfrozen pies
2nd or 3rd level
from bottom
When baking on two racks, arrange racks on
bottom and third level from bottom.
NOTE: For recommended rack placement when
broiling, see “Broiling rack position chart” on
page 14.
6
I
For best air circulation
The hot air must circulate around the pans in the
oven for even heat to reach all parts of the oven.
This results in better baking.
l Place the pans so that one is not directly over
the other.
l For best results,
allow 1 ‘%to 2 inches (4-5 cm)
of space around each pan and between pans
and oven walls. There must be a minimum space
of 1 inch (2.5 cm).
l Use only one cookie sheet in the oven at one
time.
Use the following as a guide to determine where
to place the pans.
One pan
Place in the center of the oven rack.
Two pans
Place in opposite corners of the oven rack
Three or four pans
Place in opposite corners on each oven rack.
Stagger pans so no pan is directly over another.
NOTE: Do not allow pans to touch heat sensor
on left wall near the back. Poor baking may
result.
Using
aluminum
foil for baking
Use aluminum foil to catch spillovers from pies or
casseroles.
l Place the foil on the oven rack below the rack
with the food. Turn up foil edges and make
sure foil is about 1 inch (3 cm) larger all around
than the dish holding the food.
l Do not cover
the entire rack with aluminum foil.
It will reduce air circulation and cause poor
cooking results.
l Do not line oven bottom or entire oven rack
with foil or other liners. Poor baking will result.
Do not allow foil to touch the heating
elements because it will damage them and
could result in shock or fire hazard.
7
The electronic
oven control
Electronic
selector
pa&
pads
MEALTIMER
control pads
Display/clock
l
l
l
l
l
l
When you first plug in the oven, a time of day
and “PF will show in the temperature display.
If, after you set the clock (page 9) the display
again shows “PF, your electricity was off for a
while. Reset the clock.
When you are not using the oven, this is an
accurate clock.
When using the oven or Minute Timer, the
display will show the time, temperature settings
and what command pads have been pressed.
When showing the time of day, the display
will show hours and minutes.
When using the Minute Timer, the display will
show minutes and seconds in the following
sequence:
- For settings from 1-59 minutes, the display
will count down each second.
- For settings over 1 hour, the display will
count down each minute.
When using Cook Time and/or Stop Time,
the display will show hours and minutes.
Clock
pada
pads
Command
Minute timer set
enter
pad
cancel
pad
pads
The command pads tell the oven what to do and
in what order. A few examples:
-Clock/Set
tells the oven you are going to set
the clock.
-Off/Cancel
tells the oven to turn off.
Each command pad (except Off/Cancel and Start/
Enter) has its own indicator. The indicator comes
on when you touch the command pad.
Setting
the clock
1. Push the Clock/Set pad. The colon flashes
and TIME will light up in the display.
2. Use the Hour and Minute pads to set the time
of day. Push the “up” (A) or “down” (V)
pad(s) until the correct time shows in the
display.
3. Push the Start/Enter
pad.
NOTE: If you do not want the clock time displayed, push and hold the Clock/Set pad for 4
seconds. To display the clock time again, push
the ClocWSet pad once, then reset the clock time
if necessary.
Using
the electronic
Minute
Timer
The Minute Timer does not start or stop the oven.
It works like a kitchen timer. It can be set in hours
and minutes up to 11 hours, 59 minutes. The
Minute Timer will display minutes and seconds for
settings under one hour. You will hear four
1 -second tones when the set time is up.
TIMER
1. Push the Timer Set pad. TIMER will come on
and the display will show “0:OO” with the colon
flashing.
mm
2. Use the Hour and Minute pads to set the
desired time. Push the “up” (A) or “down” (V)
pad(s) until the correct time shows in the
display.
9
3. Push the Start/Enter pad. The Minute Timer
will begin counting down immediately after the
timer is started.
When time is up, “End” will show in the large
display and you will hear four P-second tones.
You will also hear four l-second tones every
minute until you push one of the two Timer
pads.
NOTE: To disable the reminder tones, push
and hold the Timer Set pad for 4 seconds.
To reactivate the tones, follow the same
procedure.
To cancel
l
the Minute
Timer:
Push the Timer Off pad. The time of day will
show in the display.
Using
the Off/Cancel
The Off/Cancel pad will cancel any command pad
except for the ClocWSet and Timer Set pads.
When you push the Off/Cancel pad, the display
will show the time of day or, if Minute Timer is
also being used, the time remaining.
Audible
signals
Audible signals tell you if a function is entered
correctly or not. They also tell you when a cycle is
completed.
To shut off all signals except for the end-oftimer tone:
1. Press and hold the Stop Time pad for 4
seconds.
2. A short tone will sound to tell you the signals
have been changed.
Repeat the above steps to turn the signals
back on.
10
pad
Baking/roasting
1. Poaltion the rack(s) properly bafon turning on
the oven. To change rack position, lift rack at
front and pull out. For further information, sea
“Positioning racks and pans” on page 6.
2. Purh the Bake pad. 366’ will light up in the
small display to show the preset temperature
and BAKE will light up.
3. To cook at a dlfferent temperature,
use the
Terry pad(s). Pwh A to raise the temperature
or V to lower the temperature in 5’F increments. Use these pads until the desired
temperature shows in the small display.
4. Push the Start/Enter pad. ‘Lo”“, HEAT and
BAKE light up in the display to show that the
oven is preheating. The temperature will
increase in 5” increments.
NOTE: The display will show “door” and a tone
will sound once a minute for 5 minutes if the
door is latched when you try to bake/roast.
You can change the temperature setting
any time after touching the Start/Enter pad by
pushing just the Temp pad(s).
5. When baking, preheat the oven. (Preheating
is not needed when roasting.) The oven is
preheated when you hear a one-second tone
and HEAT goes off.
6. Put food in the oven.
During baldnglroasting, the elements will
turn on and off to keep the oven temperature
at the setting.
NOTE: The top element help. heat during
baking/roasting,
but doea not turn red.
7. When baking/roasting
10 done, push the Off/
Cancel pad. The time of day will show in the
display and all other displays will go off.
11
Adjusting
the oven temperature
Oven temperature controls will gradually shift
after years of use. So, even though your new
oven is properly adjusted to provide accurate
temperatures, it may cook faster or slower than
your old oven.
If, after using the oven for a period of time, you
are not satisfied with the temperature settings,
you can adjust them by following these steps:
1. Push and hold the Bake pad (for about 4
seconds) until the time display shows the current
temperature offset, for example “00” if you have
not previously adjusted the temperature.
2. To adjust the temperature, use the Temp
pad(s). Push A to raise the temperature or V
to lower the temperature in 5°F increments.
You can set the temperature change to as low
as -35°F or as high as +35”F. A minus (-) sign
will appear before the number when decreasing the temperature setting to show the oven
will be cooler by the displayed amount.
3. After making the desired adjustment,
push
any command pad to enter the new offset
temperature.
12
control
Broiling
NOTE: Preheating is not necessary when broiling.
1. Position the rack before turning the oven on.
See “Broiling rack position chart” on page 14.
2. Put the broiler pan and food on the rack.
3. Close the door to the Broil Stop position (open
about 4 inches [lo.2 cm]). The door will stay
open by itself.
4. Push the Broil pad. The small display will show
“500”” and BROIL will light up.
5. Push the Start/Enter pad. HEAT, BROIL and
“500”” show in the display.
NOTE: You can change the temperature setting
any time after pushing the Start/Enter pad by
pushing just the Temp pad(s).
6. When broiling is done, push the Off/Cancel
pad. The time of day will show in the display and
all other displays will go off.
To broil at a lower
temperature:
l
l
l
If food is cooking too fast, push the Broil pad
and push the V Temp pad until ‘325’” shows in
the small display.
tf you want food to broil slower from the start,
push the Broil pad and push the V Temp pad so
a temperature between 170°F and 325°F (77°C
and 163°C) shows in the small display. These
temperature settings allow the broil heating
element to cycle and to slow cooking. The lower
the temperature, the slower the cooking. BROIL
and HEAT will light up in the display.
Fish and chicken are some foods that may cook
better if you use lower broiling temperatures.
NOTE: Leave the door partly open whenever
using the oven to broil. This allows the oven to
maintain proper temperatures.
13
Broiling
RACK POSlTlOh
FROM BOTTOM
rack position
chart
TYPE OF FOOD/
DONENESS
Hamburger patties and
thin steaks, W” thick or
less
Quickly searing food, rare
and medium steaks,
medium patties, ham
slices, fish steaks,
frankfurters
Well-done steaks and
patties, lamb chops, split
chicken, pork steaks and
chops, whole fish
Broiling
tips
9 Use the broiler pan and grid for broiling. They
are designed to drain excess liquid and fat
away from the cooking surface to help prevent
spatter, smoke or fire.
l Refer to a broiling chart in a reliable cookbook
for correct broiling times.
l After
broiling, remove the broiler pan from
the oven when you remove the food. Drippings
will bake on the pan if you leave it in the
heated oven.
Energy
saving
l
tips
Although the energy used for cooking is usually a
very small percentage of the total energy used in
the home, cooking energy can be used efficiently.
Here are some tips to help you save energy
when using your cooking product.
l Preheat
only when recommended and for the
shortest time possible.
. “Oven peeking” may cause heat loss, longer
cooking times and unsatisfactory baking
resufts. Rely on your timer to keep track of the
cooking time.
14
l
Fire Hazard
Place meat the correct distance from the
element. Meat placed too close to the
element may spatter, smoke, burn or
catch fire during broiling.
To ensure adequate grease drainage, do
not use cookie sheets or similar pans for
broiling. Also, covering the broiler grid
with foil is not recommended. Poor
drainage of grease may result in fire. If foil
is used, cut slits in foil to line up with all
openings in broiler grid. Grease can then
drain away and cool in pan.
l
l
l
Bake cakes, pies or cookies when oven is
warm. Best time is after a meal has been
cooked in it.
Plan your meals for the most efficient use of
the oven. When using the oven to cook one
food, try to cook the rest of the meal in it also.
Do not preheat when broiling, roasting or
cooking items such as casseroles.
Using
the electronic
MEALTIMER”
control
The electronic MEALTIMER” control will turn the
oven on and off at times you set . . . even when
you are not around.
Delayed time baking/roasting is ideal for foods
which do not require a preheated oven, such as
meats and casseroles. Do not use delayed time
cooking for cakes, cookies, etc. . . .
undercooking
will result.
This section discusses two methods of starting
baking/roasting now and stopping automatically
later, and three methods of starting and stopping
baking/roasting automatically. Read this section
carefully to choose which method(s) is best for
you.
Before using the electronic MEALTIMER
control, make sure the clock is set to the correct
time of day. (See “Setting the clock” on page 9.)
To start baking/roasting
and stop automatically
Method
l-Using
Cook
now
Time:
1. Position the oven rack(s) properly and put
food in the oven.
2. Push the Bake pad to enter the Bake mode.
Use the Temp pad(s) to set the desired
temperature. Push A to raise the temperature
or V to lower the temperature in 5°F increments. Use these pads until the desired
temperature shows in the small display.
After you have set the desired temperature,
the display will show the set temperature and
the time of day. BAKE will light up.
3. Push the Cook Time pad. “0:OO” with the
colon flashing and COOK TIME will show in
the display.
15
4. Use the Hour and Minute pads to set the
desired cooking time. Push the “up” (A) or
“down” (V) pad(s) until the correct time shows
in the display.
This example shows a desired bakinq/roasting
time of 30 minutes.
5. Push the Start/Enter pad. “Lo”“, HEAT,
BAKE, TIMED and the set cook time will light
up in the display to show that the oven is
heating.
NOTE: The display will show “door” and a
tone will sound once a minute for 5 minutes if
the door is latched when you try to bake/roast.
You can change the temperature or time
settings any time after pushing the Start/Enter
pad by repeating just Steps 2 through 4.
6. The display will count down the baking/
roasting time in minutes.
7. When the baking/roasting
time is corn
pleted, the oven will turn off automatically,
beep four times and “End” will show in the
display. You will also hear four 1-second
tones every minute until you push the On/
Cancel pad.
NOTE: To disable reminder tones, push and
hold the Cook Time pad for 4 seconds. To
reactivate tones, repeat this procedure.
To cancel the MEALTIMER”
control setting:
l
Push the Off/Cancel pad to return the display
to the time of day.
Method
2-Using
Stop
Time:
1. Position the oven rack(s) properly and put
food in the oven.
16
2. Push the Bake pad to enter the Bake mode.
Use the Temp pad(s) to set the desired
temperature. Push A to raise the temperature
or V to lower the temperature in 5°F increments. Use these pads until the desired
temperature shows in the small display.
After you have set the desired temperature,
the display will show the set temperature and
the time of day. BAKE will light up.
3. Push the Stop Time pad. The time of day with
the colon flashing and STOP TIME will show in
the display.
4. Use the Hour and Minute pads to set the
desired stop time. Push the “up” (A) or “down”
(‘V’Vrd(s) until the correct time shows in the
This example shows a desired stop time of
2 o’clock. This provides a 2-hour cook time
(the difference between the time of day and the
stop time).
5. Push the Start/Enter Pad. “Lo”“, HEAT, TIMED
and BAKE will light up in the display to show
that the oven is heating.
NOTE: The display will show Udoof and a tone
will sound once a minute for 5 minutes if the
door is latched when you try to bake/roast.
You can change the temperature or time
settings any time after pushing the StarVEnter
pad by repeating just Steps 2 through 4.
6. The display will count down the baking/roasting
time in minutes.
7. When the baking/roasting
time is corn
pleted, the oven will turn off automatically,
beep four times and “En< will show in the
display. You will also hear four 1-second tones
every minute until you push the Off/Cancel
pad.
NOTE: To disable reminder tones, push and
hold the Cook Time pad for 4 seconds. To
reactivate tones, repeat this procedure.
To csncel the MEALTIMER”
control setting:
l Push the Off/Cancel
pad to return the display to
the time of day.
17
To delay start
automatically
Method
l-Using
and Delay Start
and stop
Cook
Time:
Time
1. Position the oven rack(s) property and put
food in the oven.
2. Push the Bake pad to enter the Bake mode.
Use the Temp pad(s) to set the desired
temperature. Push A to raise the temperature
or V to lower the temperature in 5’F increments. Use these pads until the desired
temperature shows in the small display.
After you have set the desired temperature,
the display will show the set temperature and
the time of day. BAKE will light up.
3. Push the Cook Time pad. ‘COO” with the
colon flashing and COOK TIME will show in
the display.
4. Use the Hour and Minute pads to set the
desired cooking time. Push the “up” (A) or
Ydown” (V) pad(s) until the correct time shows
in the display.
This example shows a desired bakkrglroasting
time of 30 minutes.
5. Push the Delay Start Time pad. The time of
day with the colon flashing will show in the
display and START TIME will light up.
18
Use the Hour and Minute pads to set the
desired start time. Push the “up” (A) or “down”
(V;ryd(s)
until the correct time shows in the
This example shows a desired start time of 2
o’clock. The oven will automatically shut off at
2:30 (the set start time plus the set cook time).
Push the Start/Enter pad. DELAY and BAKE
will light up in the display to show that the oven
is programmed to start at a later time.
NOTE: The display will show “door” and a tone
will sound once a minute for 5 minutes if the
door is latched when you try to bake/roast.
You can change the temperature or time
settings any time after pushing the Start/Enter
pad by repeating just Steps 2 through 6.
When the start time is reached, a one-second
tone will sound and DELAY will go off. The
display will show the set cook time. “Lo”“,
HEAT, TIMED and BAKE will light up in the
display to show that the oven is heating. The
display will count down the baking/roasting time
in minutes.
When the baking/roasting
time is corn
pleted, the oven will turn off automatically,
beep four times and “End” will show in the
display. You will also hear four 1-second tones
every minute until you push the Off/Cancel pad.
NOTE: To disable reminder tones, push and
hoki the Cook Time pad for 4 seconds. To
reactivate tones, repest this procedure.
To cancel the MEALTlMER”control
setting:
l Push the Off/Cancel
pad to return the display to
the time of day.
19
Method
2-Using
Delay
Time and Stop Time:
Start
1. Position the oven rack(s) properly and put
food in the oven.
2. Push the Bake pad to enter the Bake mode.
Use the Temp pad(s) to set the desired
temperature. Push A to raise the temperature
or V to lower the temperature in 5°F increments. Use these pads until the desired
temperature shows in the small display.
After you have set the desired temperature,
the display will show the set temperature and
the time of day. BAKE will light up.
3. Push the Delay Start Time pad. The time of
day with the colon flashing will show in the
display and START TIME will light up.
4. Use the Hour and Minute pads to set the
desired start time. Push the “up” (A) or
“down” (V) pad(s) until the correct time shows
in the display.
This example shows a desired start time of
2 o’clock.
5. Push the Stop Time pad. The time of day with
the colon flashing will show in the display and
STOP TIME will light up.
20
6. Use the Hour and Minute pads to set the
desired stop time. Push the “up” (A) or “down”
(V) pad(s) until the correct time shows in the
display.
This example shows a desired stop time of
2:30. This provides a cook time of 30 minutes
(the difference between the start and stop
times).
NOTE: If you do not set a stop time, the colon
will flash in the display and STOP and COOK
will flash alternately to remind you to program
a stop time or a cook time. (See page 18 for
instructions on how to set delay start and stop
automatically using Cook Time and Delay
Start Time.)
7. Push the Start/Enter pad. DELAY and BAKE
will light up in the display to show that the oven
is programmed to start at a later time.
NOTE: The display will show “door” and a tone
will sound once a minute for 5 minutes if the
door is latched when you try to bake/roast.
You can change the temperature or time
settings any time after pushing the Start/Enter
pad by repeating just Steps 2 through 6.
8. When the start time is reached, a onesecond tone will sound and DELAY will go off.
The display will show the set cook time. “Lo”“,
HEAT, TIMED and BAKE will light up in the
display to show that the oven is heating. The
display will count down the baking/roasting
time in minutes.
9. When the baking/roasting
time is cornpleted, the oven will turn off automatically,
beep four times and “End” will show in the
display. You will also hear four 1-second tones
every minute until you push the Off/Cancel
pad.
NOTE: To disable reminder tones, push and
hold the Cook Time pad for 4 seconds. To
reactivate tones, repeat this procedure.
To cancel the MEALTIMER”
control setting:
l Push the Off/Cancel
pad to return the display to
the time of day.
21
Method
3-Using
and Stop Time:
Cook
Time
1. Position the oven rack(s) properly and put
food in the oven.
2. Push the Bake pad to enter the Bake mode.
Use the Temp pad(s) to set the desired
temperature. Push A to raise the temperature
or V to lower the temperature in 5°F increments. Use these pads until the desired
temperature shows in the small display. After
you have set the desired temperature, the
display will show the set temperature and the
time of day. BAKE will light up.
3. Push the Cook Time pad. “0:OO” with the
colon flashing and COOK TIME will show in
the display.
4. Use the Hour and Minute pads to set the
desired cooking time. Push the “up” (A) or
“down” (V) pad(s) until the correct time shows
in the display.
This example shows a desired baking/roasting
time of 30 minutes.
5. Push the Stop Time pad. The time of day with
the colon flashing will show in the display and
STOP TIME will light up.
6. Use the Hour and Minute pads to set the
desired stop time. Push the “up” (A) or
“down” (V) pad(s) until the correct time shows
in the display.
22
This example shows a desired stop time of
2:30. The oven will automatically start
cooking at 2:00 (the set stop time minus the
set cook time).
7. Push the Start/Enter pad. DELAY and BAKE
will light up in the display to show that the
oven is programmed to start at a later time.
NOTE: The display will show “doo? and a tone
will sound once a minute for 5 minutes if the
door is latched when you try to bake/roast.
You can change the temperature or time
settings any time after pushing the Start/Enter
pad by repeating just Steps 2 through 6.
8. When the start time is reached, a onesecond tone will sound and DELAY will go
off. The display will show the set cook time.
“Lo”“, HEAT, TIMED and BAKE will light up in
the display to show that the oven is heating.
The display will count down the baking/
roasting time in minutes.
9. When the baking/roasting
time is corn
pleted, the oven will turn off automatically,
beep four times and “End” will show in the
display. You will also hear four 1-second
tones every minute until you push the Off/
Cancel pad.
NOTE: To disable reminder tones, push and
hold the Cook Time pad for 4 seconds. To
reactivate tones, repeat this procedure.
To cancel the MEALTIMER”
control setting:
l Push the Off/Cancel
pad to return the display
to the time of day.
To avoid sickness and food waste when
using the MEALTIMERIY control:
l Do not let most UNFROZEN
food stand
for more than two hours before cooking
starts.
l Do not allow food to remain in oven for
more than two hours after the end of
cooking cycle.
NOTE: Do not use foods that will spoil while
waiting for cooking to start. Such foods are:
dishes with milk or eggs, cream soups and
cooked meats or fish. Also, foods containing
baking powder or yeast will not rise properly
when cooked using delay start.
23
The oven vent
Ovai vent
24
Using The Self-Cleaning
Cycle
In This
Section
Paw
How the cycle works ........................................ 25
Before you start ..............................................*. 25
Page
Setting the controls ..................... ..................... 26
Special tip8 ......................... ...................... ......... 29
The Self-Cleaning cycle saves you from the toil and mess that often come with hand-cleaning the oven
interior. Like with the other functions of your oven, you operate the SeWleaning
cycle with the easy-touse electronic control. Please review the instructions in this section to keep your oven spotless.
How the cycle
works
The Self-Cleaning cycle uses very high heat to
burn away soil and grease. During the cycle, the
oven gets much hotter than it does for normal
baking or broiling. This high heat breaks up the
soil or grease and burns it away.
Your oven is preset for a &hour Seff-Cleaning
cycle. However, you can adjust the cycle time to
the amount of soil in your oven. You can set the
cycle anywhere between 2 and 4 hours. (See
“Setting the controls” on page 26.)
The graph at the right is representative of a
normal, 3-hour Self-Cleaning cycle. Note that the
heating stops when the &hour setting is up, but it
takes longer for the oven to cool enough to
unlock
Before
START
3
1
The
STOP
I,’ Howo
you start
Before you start the Self-Cleaning
cycle, make
sure you:
l Hand-clean
the areas shown. They do not get
hot enough during the cleaning cycle for soil to
burn away. Use hot water and detergent or a
soapy steel-wool pad for cleaning.
NOTE: DO NOT clean, move or bend the seal.
Poor cleaning, baking and roasting may result.
Hand-clean
Hand-+e?n door /[ff
around edge
25
l
l
l
l
Remove the broiler pan grid and any pots
and pans being stored in the oven.
NOTE: You can clean the broiler pan (without
grid) in the oven if you have first removed most
of the soil by hand-cleaning or a dishwasher. If
most of the soil is not removed, too much
smoking will occur. The chrome broiler pan grid
will discolor if cleaned in the Self-Cleaning
cycle.
Wipe out any loose aoil or grease. This will
help reduce smoke during the cleaning cycle.
Remove the oven rackr from the oven if you
want them to remain shiny. You can clean the
oven racks in the Seff-Cleaning cycle, but they
will become harder to slide. (See page 30.) If
you clean racks in the Self-Cleaning cycle,
place them on the 2nd and 4th rack guides.
(Guides are counted from bottom to top.)
Hent and odors are normal during the SelfCleaning cycle. Keep the kitchen well ventilated
by opening a window or by turning on a vent
hood or other kitchen vent during the cycle.
Setting
the controls
1. Make sure the clock is set to the correct time
of day. (See “Setting the cloclc on page 9.)
2. Lii the panel between the oven door and the
control panel. Move the Lock Lever all the
way to the right-the Clean position.
3. Set cleaning cycle.
To atart cleaning immediately:
Push the Clean pad. A 3-hour Seff-Cleaning
cycle will be set automatically. “3:OO” with the
colon flashing will show in the large display
and “cln” will show in the small display. TIME,
CLEAN (on right side) and CLEAN (on left
side) will light up.
26
l
l
l
Personal lniury and
Product Damage Hazard
Do not touch the oven during the SelfCleaning cycle. it could bum you.
Do not use commercial oven cleaners in
your oven. Cleaners may produce hazardous fumes or damage the porcelain finish.
Do not leave foil in the oven during the SelfCleaning cycle. Foil can burn or meft and
damage the oven surface.
NOTE: Do not force the Lock Lever. You could
bend or break ft. The lever is designed to stay
locked until the oven is cool enough to safely
open. Wait until it moves freely.
Do not block the vent during the Seff-Cleaning
cycle. Air must move freely for best cleaning
resufts.
Do not leave plastic utensils near the vent.
They may melt.
If a cleaning cycle other than 3 hours is
desired, use the Hour and Minute pads
to set the desired cleaning time. Push the
“up” (A) or “down” (r) pad(s) until a time
between 2-4 hours shows in the display.
l Use 2 hours for light soil.
l Use 3-4 hours for moderate to heavy soil.
Push the StatiEnter pad. TIMED and HEAT
will light up in the display to show that the
oven is programmed for the Self-Cleaning
cycle.
NOTE: The display will show “door” and a tone
will sound once a minute for 5 minutes if the
door is not latched.
Skip to Step 4.
To delay the start using Stop Tim:
Purh the Clean pad. Push the Stop Time pad.
STOP, TIME, CLEAN and “cln” will light up.
Use the Hour and Minute pads to set the
desired stop time. Push the “up” (A) or “down”
(V) pad(s) until the correct time shows in the
display. The oven will automatically compute
the delay start time by subtracting the set
cleaning time from the set stop time.
Push the Start/Enter pad. DELAY, CLEAN
and the time of day will light up in the display
to show that the oven is programmed to start
the Self-Cleaning cycle at a later time.
Skip to Step 4.
27
To delay the start using Delay Start Time:
Push the Clean pad. Push the Delay Start
Time pad. START, TIME, CLEAN and “cln”
will light up. Use the Hour and Minute pads to
set the desired start time. Push the “up” (A)
or “down” (V) pad(s) until the correct time
shows in the display.
Push the Start/Enter pad. DELAY, CLEAN
and the time of day will light up in the display
to show that the oven is programmed to start
the Self-Cleaning cycle at a later time.
After the start time has been set, the
large display will go back to showing the
current time of day. DELAY and CLEAN will
stay on. When the start time is reached,
DELAY will go off, TIMED, CLEAN and
CLEAN TIME will light up and the oven will
start to clean.
4. After the Self-Cleaning
cycle is started,
LOCKED lights up in the display when the
oven temperature goes above normal baking/
roasting temperatures. The Lock Lever must
not be moved and the door cannot be opened
when LOCKED is on.
5. After the Self-Cleaning
cycle is completed,
the time of day will show in the display.
28
6. When the oven reaches normal baking/
roasting temperatures,
LOCKED goes off
and “End” and CLEAN TIME come on. Move
the Lock Lever back to the left. DO NOT
FORCE lT. Wait until it moves easily.
To stop the Self-Cleaning
cycle at any time:
1. Push the Off/Cancel pad.
2. When LOCKED goes off, move the Lock
Lever back to the left. DO NOT FORCE lT.
Wait until it moves easily.
Special
l
l
l
tips
Keep the kitchen well ventilated during the SelfCleaning cycle to help get rid of heat, odors and
smoke.
After the oven is cool, wipe up any residue or
ash with a damp cloth or sponge. If any spots
remain, clean with a mild abrasive cleanser or
mildly abrasive pad.
Clean the oven before it gets heavily soiled.
Cleaning a very soiled oven takes longer and
resutts in more smoke than usual.
. If the Self-Cleaning cycle does not get the oven
as clean as you expected, the cycle may not
have been set long enough or you may not
have prepared the oven properly. Set the SelfCleaning cycle longer the next time and handclean areas noted on page 25.
Caring For Your Oven
In This
Section
Page
Cleaning chart .............. ..................................... 30
Page
The oven light .............. .......................... ........... 31
Your oven is designed for ease of care. You can
do most cleaning with items found around your
home. Cleaning your oven whenever spills or
soiling occurs will help to keep it looking and
operating like new.
I
Burn and Electrical Shock Hazard
Make sure all controls are off and the oven
is cool before cleaning or servicing.
Failure to do so could result in burns or
electrical shock.
I
29
Cleaning
chart
Use the following table to help you clean all parts of your oven.
PART
Control
panel
Sponge and warm, soapy
water
OR
Paper towel and spray
glass cleaner
Exterior surfaces
(other than control
panel)
Sponge and warm, soapy
water
Broiler pan and grid
(clean after each use)
Steel-wool pad and warm,
soapy water
Oven racks
Steel-wool pad and warm,
soapy water
OR
The Seff-Cleaning cycle
Oven door glass
HOW TO CLEAN
WHAT TO USE
Paper towel and spray glass
cleaner
Wash, rinse and dry thoroughly.
DO NOT USE steel wool or abrasive
cleaners. They may damage the finish.
DO NOT spray cleaner directly on panel.
Apply cleaner to paper towel.
NOTE: Make sure you have not turned the
oven on when cleaning panel. If you
have, push the Off/Cancel pad.
l
l Wash, rinse and dry thoroughly.
USE nonabrasive, plastic scrubbing pad on
heavily soiled areas.
l Do not use abrasive
or harsh cleansers.
They may damage the finish.
Wash, rinse and dry thoroughly.
DO NOT CLEAN in Setf-Cleaning
(See note on page 26.)
l
l
OR
Leave in oven during Self-Cleaning cycle.
NOTE: Racks will permanently discolor and
become harder to slide if left in oven during
Seff-Cleaning cycle. Apply a small amount 01
vegetable oil to the side rungs to aid sliding.
l
l
l
Warm, soapy water and a
nonabrasive, plastic scrubbing pad
30
Seff-Cleaning
cycle
Wash, rinse and dry thoroughly.
l
OR
Oven cavity
cycle.
l
Make sure oven is cool.
Follow directions provided with the
cleaner.
Wash, rinse and dry thoroughly.
See “Using The Self-Cleaning
pages 25-29.
Cycle” on
The oven light
The oven light
is opened. To
door is closed,
control panel.
the light.
l
l
will come on when the oven door
turn on the light when the oven
use the Oven Light Switch on the
Use the switch again to turn off
Electrical Shock and
Personal Injury Hazard
Make sure oven and light bulb are cool
and power to the oven has been turned
OFF before replacing the light bulb.
Failure to do so could result in electrical
shock or burns.
The bulb cover must be in place when
using the oven. The cover protects the
bulb from breaking, and from high oven
temperatures. Since bulb cover is made
of glass, be careful not to drop it. Broken
glass could cause injury.
To replace
1. Turn off
2. Remove
the oven
3. Remove
Replace
bulb.
the oven
light:
power at the main power supply.
the glass bulb cover in the back of
by screwing it out counterclockwise.
the light bulb from its socket.
the bulb with a 40-watt appliance
4. Replace the bulb cover by screwing it in
clockwise. Turn power on at the main power
supply.
NOTE: The oven light will not work during the
Self-Cleaning cycle.
31
If You Need Assistance
Or Service
This section is designed to help you save the cost of a service call. Part 1 of this section outlines
possible problems, their causes, and actions you can take to solve each problem. Parts 2 and 3 tell you
what to do if you still need assistance or service. When calling our Consumer Assistance Center for
help or calling for service, please provide a detailed description of the problem, your appliance’s
complete model and serial numbers and the purchase date. (See page 2.) This information will help us
respond properly to your request.
1. Before
calling
for assistance
...
Performance problems often result from little things you can find and fix without tools of any kind.
Please check the chart below for problems you can fix. It could save you the cost of a service call.
PROBLEM
Nothing
operate
will
POSSIBLE
CAUSE
The unit is not wired into a live
circuit with proper voltage.
You have programmed
start time.
The Self-Cleaning
cycle will not
operate
32
a delayed
1 The oven clock does not show the
correct time of day.
The Lock Lever is not in the Clean
position-all the way to the right.
You have programmed a delayed
I start time.
SOLUTION
Wire the unit into a live circuit with proper
voltage. (See Installation Instructions.)
Replace household fuse or reset circuit
breaker.
Refer to the section in this manual
describing the function you are operating.
Wait for the start time to be reached.
Reset clock to show the correct time of
day. (See page 9.)
Move Lock Lever all the way to the right.
Wait for the start time to be reached.
PROBLEM
Cooking results
are not what you
expected
POSSIBLE
CAUSE
The oven is not level.
The oven temperature
low or too high.
Level oven. (See Installation
seems too
You have not preheated the
oven before baking.
The recipe has never been
tested or is not from a reliable
source.
The pan used is not the type or
size recommended in the recipe.
There is not proper air circulation
around pan when baking.
The display
shows “PF”
“F, I. or “F3”
SOLUTION
There has been a power failure.
Instructions.)
Adjust the oven temperature control.
(See “Adjusting the oven temperature
control” on page 12.)
Preheat oven when called for in recipe.
Use only tested recipes from a reliable
source.
Refer to a reliable cookbook for recommended pan type and size.
Allow 1% to 2 inches (4-5 cm) of air space
on all sides of pan. There must be a
minimum space of 1 inch (2.5 cm).
Reset the clock (See page 9.)
Call for service. (See Step 3 on page 34.)
shows in the
display
33
2. If you need
assistance
...
Call Whirlpool Consumer Assistance
Center
telephone number. Dial free from anywhere in
the U.S.:
l-800-253-1301
and talk with one of our trained consultants. The
consultant can instruct you in how to obtain
satisfactory operation from your appliance or, if
service is necessary, recommend a qualified
service company in your area.
If you prefer, write to:
Mr. William Clark
Consumer Assistance Representative
Whirlpool Corporation
2000 M-63
Benton Harbor, Ml 49022
Please include a daytime phone number in your
correspondence.
3. If you need
service
Whirlpool has a nationwide
m network of authorized
01
WhirlpoolSM service compaSERVrcEnies. Whirlpool service
9
technicians are trained to
fulfill the product warranty and provide afterwarranty service, anywhere in the United States.
To locate the authorized Whirlpool service
company in your area, call our Consumer
Assistance Center telephone number (see
Step 2) or look in your telephone directory
Yellow Pages under:
- Sea’ Whirlpool Appllames
or
Authorlad
WhIrlpool Service
(Exsmpre: XYZ sen4ce Co.)
34
* WASHING
DRYERS,
MACHINES
6
SERVICE 6 REPAlR
- Sez WhIrlpool Appliames
or
Aulhorlmd
Whirlpool Servlca
(E~mpk:
xY2 service Co.)
replace-
FSP is a registered trademark of Whirlpool
Corporation for quality parts. Look for this symbol
of quality whenever you need a replacement part
for your Whirlpool appliance. FSP replacement
parts will fit right and work right, because they
are made to the same exacting specifications
used to build every new Whirlpool appliance.
To locate FSP replacement parts in your area,
refer to Step 3 above or call the Whirlpool
Consumer Assistance Center number in Step 2.
5. If you are not satisfied
how the problem
was
solved . . .
l
...
-.
‘APPLIANCE-HOUSEHOLDMAJOR, SERVlCE 6 REPAJR
4. If you need FSP
ment parts . . .
l
l
with
Contact the Major Appliance Consumer Action
Panel (MACAP). MACAP is a group of independent consumer experts that voices consumer views at the highest levels of the major
appliance industry.
Contact MACAP only when the dealer,
authorized servicer and Whirlpool have failed
to resolve your problem.
Major Appliance Consumer Action Panel
20 North Wacker Drive
Chicago, IL 60606
MACAP will in turn inform us of your action.
35
WHIRLPOOL”
Microwave
Oven/Range
Product Warranty
LENGTH OF WARRANTY
WHIRLPOOL
FULL ONE-YEAR WARRANTY
From Date of Purchase
FSpb replacement parts and repair labor to correct defects in
materials or workmanship. Service must be provided by an
authorized Whirlpools’ service company.
LlMlTED FOUR-YEAR
WARRANTY
Second Through Fifth Year From
Date of Purchase
FSpd replacement magnetron tube on microwave
defective in materials or workmanship.
WHIRLPOOL
WlLL PAY FOR
ovens if
WlLL NOT PAY FOR
k Service calls to:
1. Correct the installation of the range product.
2. Instruct you how to use the range product.
3. Replace house fuses or correct house wiring.
4. Replace owner accessible light bulbs.
B. Repairs when the range product is used in other than normal, single-family household use.
C. Pickup and delivery. This product is designed to be repaired in the home.
D. Damage to the range product caused by accident, misuse, fire, flood, acts of God or use of
products not approved by Whirlpool.
E. Any labor costs during limited warranty.
F. Repairs to parts or systems caused by unauthorized modifications made to the appliance.
R-02
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so this limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
Outside the United States, a different warranty may apply. For details, please contact your authorized
Whirlpool distributor or military exchange.
If you need service, first see the “Assistance or Service” section of this book. After checking “Assistance
or Service,” additional help can be found by calling our Consumer Assistance Center telephone number,
l-800-253-1301,
from anywhere in the U.S.
PART NO. 3184425 Rev. A
0 1883 Whlrlpod
Corporation
@ Regi~aerad
TfadamsrWTM
TrademerWSM
Swvke
Mark of Whirlpool
Corpate(ion.
Printed
in U.S.A.