VADDIO WallVIEW 50i PTZ HideAway Installation and User Manual

Add to my manuals
14 Pages

advertisement

VADDIO WallVIEW 50i PTZ HideAway Installation and User Manual | Manualzz

Camera and Electronic Products for Integrators

Installation and User Guide

WallVIEW ™ 50i PTZ HideAway

Installed PTZ Wall Camera with Recessed, Motorized In-wall Camera Lift System

INTRODUCTION

The Vaddio WallVIEW 50i PTZ HideAway Camera System is a mechanically unique and complete product that was designed to provide system integrators with an easy to install, in-wall, recessed and motorized camera lift system for use when cameras require concealment for security or architectural design purposes. The

WallVIEW 50i features the Canon

®

VC-C50i pan/tilt/zoom camera which is mounted in a recessed plenum rated enclosure with a motorized front panel door. When closed, the WallVIEW HideAway enclosure conceals the camera until the camera is activated, then the front door drops down and reveals the camera to the meeting room participants.

The system is equipped with Vaddio’s EZCamera™ Cabling

System. This allows the integrator to use Cat. 5 cabling to run power and video together on a single Cat.5 and camera control on a second Cat. 5 run. The VISCA control interface is included to allow the camera to work with any other VISCA compatible control device. The PowerRite™ power supply regulates the right amount of power needed for the camera over the Cat. 5 cabling.

INTENDED USE

Before operating the Vaddio WallVIEW 50i PTZ HideAway, please read the entire manual thoroughly. The camera system was designed, built and tested for use indoors and with the provided power supply. The use of a power supply other than the one provided or outdoor operation has not been tested and could damage the camera and/or create a potentially unsafe operating condition.

SAVE THESE

INSTRUCTIONS

The information contained in this manual will help you install and operate your Vaddio WallVIEW 50i PTZ HideAway. If these instructions are misplaced, Vaddio keeps copies of Specifications,

Installation and User Guides and most pertinent product drawings for the Vaddio product line on the website. These documents can be downloaded from www.vaddio.com

free of charge.

Ⓒ2006 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing subject to change. CeilingVIEW, WallVIEW ControlVIEW, Quick-Connect, EZCamera and PowerRite are registered trademarks of Vaddio, Inc. All other trademarks are property of their respective owners. Form Number 341-141 Rev. C.

IMPORTANT

SAFEGAURDS

UNPACKING

INSTALLATION

Read and understand all instructions before using. Do not operate the camera if the camera has been dropped or damaged. In this case, a Vaddio technician must examine the appliance before operating. To reduce the risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.

Use only the power supply provided with the WallVIEW 50i HideAway camera system. Use of any unauthorized power supply will void any and all warranties.

Carefully remove the device and all of the parts from the packaging.

Unpack and identify the following parts:

• One (1) WallVIEW 50i PTZ HideAway camera enclosure module o

Contains Canon VC-C50i Camera inside

• White surrounding trim plate with door cut out

• White door cover plate

• Canon WL-V5 Multifunction IR Remote

• EZCamera Control Adapter

• EZCamera Quick-Connect Box

• Vaddio PowerRite 15 VDC Power Supply and Power Cable

• One (1) 12’/(3.66m) S-Video Cable

• One (1) 12’/(3.66m) Composite Video Cable

• Installation and Users Guide (document 341-141)

• Mounting Template (document 341-156) hardware

The WallVIEW 50i PTZ HideAway is an unique recessed approach to camera system installation. While the camera is easy to install, understanding of the key system components is essential.

The WallVIEW 50i PTZ HideAway is shipped closed and packed securely for transit. Before powering up the camera for the first time, make sure that any tape is removed and the door is not blocked (see Figure 1).

Figure 1: Vaddio WallVIEW 50i

HideAway enclosure shown with camera lift system (door) closed.

RJ-45 connections (for video, power

& control) and a closure pair are shown under the lift mechanism.

Note conduit knockout on lower right side of camera module backbox

(knockout on bottom not shown).

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 2 of 14

INSTALLATION

(continued)

Drywall

Mounting

The WallVIEW 50i PTZ HideAway is intended for installation into finished drywall and does not require a rough-in kit or partial preinstallation. The pre-wire requirement is for up to three (3) Cat. 5 cables; one Cat. 5 for Video and Power, one for RS-232 Input and one for RS-232 Output if required. The cables can be pre-wired or cabled at the time of installation and is strictly a function of integrator or customer preference, not product requirement.

Marking and cutting the drywall is probably the most challenging part of the whole camera installation. Behind any stud wall, the studs are either 16” or 24” on center (OC) and are either wood or metal. The WallVIEW will fit between either stud configurations.

The following steps should be followed for best installation results:

1. Determine the position of the camera. a. Consider camera height, viewing angles and distances from the subject matter, sight lines, possible temporary obstructions (audience member heads) and the PTZ specifications of the camera.

2. Determine the locations of the studs behind the drywall. a. The camera module can be located between the studs using dry wall toggle bolts (supplied). b. The camera module can alternately be located with one of the camera’s mounting flanges over a stud (using appropriate screws for stud type – not supplied) with the opposite side mounting flanges using the supplied toggle bolts.

IMPORTANT: Ensure that there are NO obstructions such as horizontal studs behind the drywall and verify that there are NO utilities (electrical, gas, water and phone/data) in this drywall area between the studs.

3. With the supplied mounting template (see the provided document 341-156 WallVIEW Template) measure and mark the rough wall opening, (9-3/16”(23.34cm) tall x 6-3/8”(16.2cm) wide, and verify that the template is level. Also mark the four (4) mounting holes in the camera enclosure mounting flanges on both sides of the camera module. a. Verify positioning of camera before cutting the drywall.

4. Cut rough opening in sheetrock (or direct qualified drywall installer to cut opening).

5. Carefully slide camera module into the wall opening, and with mounting flanges against the wall and the camera module level, verify the four mounting screw locations while leveling the camera.

6. Remove the camera module from the wall and drill the four

5/8”/(1.59cm) holes for the supplied toggle bolts (see Figure 2).

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 3 of 14

Mounting

Template

Cabling

6-3/8”

Figure 2:

WallVIEW 50i HideAway backbox mounting template (not to scale)*

*Use printed template 341-156 provided with manual.

Note: Level template prior to cutting drywall.

9-3/16”

7. The Cat. 5 cabling can be routed in the wall cavity at this time.

Please check with your local municipalities for local building codes as some cities like Chicago and New York require conduit for all cabling. For this reason, the WallVIEW 50i PTZ

HideAway is equipped with a conduit knockout for either routing cables through into the wall cavity or for the attachment of conduit where required (see Figure 3).

Figure 3:

Side view of WallVIEW 50i

PTZ HideAway

Note: Conduit knockout on side and bottom of camera module that leads to Cat. 5 interface connections inside the module.

Side and

Bottom

Conduit

Knockouts

8. Remove the conduit knockout(s) and pull the Cat. 5 cables for

Power/Video and RS-232 (one for RS-232 Input & one for RS-

232 Output if used in a daisy-chained control configuration) in the wall cavity through the conduit knockout to the Cat. 5 cable interface module in the bottom of the camera module enclosure.

Connect the power and video Cat. 5 to the RJ-45 jack labeled

POWER VIDEO and the corresponding RS-232 control Cat. 5

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 4 of 14

Connection

Camera

Mounting cables to the RS-232 IN (from ControlVIEW Xtreme or control system) and RS-232 OUT (to the next Vaddio VISCA controlled camera product in the control chain. A closure pair (voltage sensing) is also provided to control the opening of the WallVIEW

50i PTZ HideAway independent of the IR remote controller provided with the system. To take advantage of this feature, an additional two-conductor cable is a requirement (see Figure 4).

Figure 4:

Cat. 5 connections and closure pair in camera module (under camera)

Note: The closure pair opens the WallVIEW camera door when the camera is off and has power available ONLY.

The closure pair will not raise the camera.

POWER

VIDEO

RS-232

IN

RS-232

OUT

Closure Pair

(For limited use only)

9. Using the four (4) ¼” x 2” supplied toggle screws, insert the screws through the front of the mounting flange’s mounting holes and secure the toggles to the screws but only turn two or three threads. Verify that the toggles open toward the back of the mounting flange. Carefully insert the camera module backbox with attached cables into the drywall-mounting hole aligning the toggle bolts and press firmly and completely into the wall. Tighten the four mounting screws securely but do not over tighten.

Connection 10. Connect the Cat. 5 cable from the WallVIEW 50i PTZ HideAway

POWER/VIDEO Jack to the supplied Vaddio Quick-Connect

Box. This single Cat. 5 cable is broken out to the following connections (see Figure 5):

• S-Video Output

• Composite Video Output

• Power Supply Input

Figure 5:

Vaddio Quick-Connect Box for power and video breakout

• Note: Rack mountable Quick-

Connect bracket is available as an option.

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 5 of 14

Connection

(continued)

Initial

Camera

Activation

Attaching

Trim Plates

11. Connect the video outputs from the Quick-Connect Box (S-

Video, Composite Video, or Both) to the video input(s) of the video device(s) of choice (ControlVIEW Xtreme, codec, monitor, switcher, etc…).

12. To power up the camera for the first time, connect the supplied

15 VDC power supply to the Quick-Connect Box. The door of the camera module will open and the Canon VC-C50i camera will be lowered and “home” into operating position.

13. Remove all foam inserts and packing material inside of the camera module and inspect the camera for integrity and connections. The S-Video or Composite Video outputs can be viewed, tested and verified for signal strength and integrity.

14. Attach the door trim plate with the four (4) supplied screws making sure not to over tighten the screws. . The camera must be lowered into down position to attach the door trim plate.

15. Plug in the IR Sensor cable to the IR Sensor mounted to the back of the surrounding trim plate (see Figure 6). Next, attach the surrounding camera module trim plate with the four (4) supplied screws. These screws are attached through the sides of the trim plate return flange into the blocks mounted on the front of the camera module mounting flanges (see Figure 7).

Position the surrounding trim plate to provide an even gap between the door trim plate and the surrounding trim plate.

Again, do not over tighten screws or damage may result.

Figure 6:

Front view of WallVIEW 50i

HideAway

Note location of IR Sensor on front of surrounding trim plate.

WallVIEW 50i HideAway – Document 341-141 Rev. C

Figure 7:

Side view of WallVIEW 50i

HideAway with surrounding trim plate

Note location of side mounting screws (do not over tighten)

Page 6 of 14

Operating the Camera

Installation

Complete

16. After the initial power up, the WallVIEW 50i PTZ HideAway can be opened and closed with the supplied Canon WL-V5 IR

Remote controller or by the ON/OFF RS-232C commands on page 9. To open and close the camera with the IR Remote, press the on/off button marked in green (see Figure 8).

Figure 8:

Canon WL-V5 Remote and

Universal On/Off button

The WallVIEW 50i will respond to all of the WL-V5 remote commands with the On/Off button opening and closing the WallVIEW.

On = Open

Off = Closed

17. The installation of the Vaddio WallVIEW 50i PTZ HideAway is now complete. With a soft cloth, please dust the exposed surfaces of the product (avoid the camera lens) to remove any sheetrock dust or other construction materials. Both WallVIEW trim plates are painted an unobtrusive white painted finish. The trim plates can be painted to match any décor (see Figure 9).

Figure 9:

The Vaddio WallVIEW 50i

HideAway shown closed.

Note: The door and surrounding trim plates are paintable to match the décor in any room.

Important Note:

Mask or Remove the IR Sensor prior to painting the surrounding trim plates. Re-install IR Sensor after paint has dried completely.

White nylon screw

(nylon nut on backside) attaches

IR Sensor to the surrounding trim plate.

IR Sensor: Relays IR signals from IR Remote to the camera with the door closed. Painting the sensor will block the

IR from reaching the camera. Mask or remove the IR Sensor prior to painting trim.

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 7 of 14

IR Control

Commands

CONTROLLING

THE CAMERA

*Control

Disclaimers

The Camera can be controlled with the Canon WL-V5 IR Remote

Controller or through RS-232 using VISCA control protocols.

Vaddio’s unique approach to camera control takes advantage of the

VISCA control allowing the WallVIEW 50i PTZ HideAway (with the

Canon VC-C50i internal) to respond flawlessly to many mainstream controllers/joysticks with built-in Sony VISCA control Protocol.

The IR signals transmitted by the Canon IR Remote are intercepted by Vaddio circuitry and are translated to RS-232 codes that the Canon VC-C50i camera can understand. Furthermore, the

VISCA control codes sent to the camera are also translated into RS-232 that the Canon VC-C50i understands. The Canon VC-C50i can accept either RS-232 control or IR codes for operation, but not both at the same time. Again, Vaddio’s approach only uses RS-232 communication to control the camera through the translation of both the VISCA protocol and Canon IR into RS-232 so both the IR and RS-232 can be used simultaneously.

When using the WallVIEW 50i PTZ HideAway with an external Codec (Polycom®, TANDBERG® etc…), the codecs typically control the cameras directly using VISCA RS-232 commands if no external control system is used. However, these codecs don’t have the ability to command the

WallVIEW 50i PTZ HideAway camera to open and close since the codecs don’t have the ability to communicate the VISCA RS-232 commands of CAMERA ON and CAMERA OFF. These codes are not programmed into the codecs. While the codecs can control the pan, tilt and zoom functions of the

WallVIEW 50i PTZ HideAway camera, the camera will remain open at all times, essentially defeating the purpose of the HideAway motorized feature. Therefore, it is recommended that the WallVIEW

50i PTZ HideAway be used with the IR Remote it is shipped with, Vaddio ControlVIEW Xtreme or

ProductionVIEW, the Vaddio/Sony Joystick bundle or an external control system (i.e.

Crestron®/AMX®) or any system that can communicate the VISCA RS-232 ON/OFF commands. If

FEC (Far End Camera) control is required in the customer’s configuration, take the camera RS-232 out from the codec into the programmable control system, intercept the Near and Far end pan/tilt/zoom camera commands from the codec and forward these commands to the WallVIEW 50i

PTZ HideAway and then simply add an ON/OFF button for the camera on the control system panel.

With any language, not all commands are specifically translatable from one manufacturer to another.

The Canon WL-V5 IR Remote Controller controls the following functions when used with a WallVIEW

50i PTZ HideAway (see Figure 10).

Figure 10:

The active Canon WL-V5 IR Remote control commands are as follows:

1) Power a. On = lowers camera door b. Off = Homes the camera and closes the camera door

2) Brightness: Up/Down

3) Zoom:

4) Pan:

Tele (in)/Wide (out)

Left, Right, Up, Down

5) Home:

6) Set/OK:

7) Cancel:

8) AF:

9) MF:

10) Keypad:

Home/Centered Position

For setting camera presets

Auto Focus On

Manual Focus On

Lengthens the focal distance

Shortens the focal distance

0 through 9 for assigning presets,

* and # not used

11) On Screen: Not used

12) Fn:

13) ID:

Not used

Not used

14) MENU: Not used

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 8 of 14

Command List

RS-232

COMMAND LIST

Communication

Specification

Vaddio supplies this control specification for the WallVIEW 50i PTZ HideAway camera. A derivate of the VISCA control set (as used in Sony EVI cameras) is used in conjunction with control translation to ensure interoperability with other manufacturers using the VISCA protocol for control purposes.

Communication Speed: 9600 bps

Start bit:

Stop bit:

1

1

Data bits:

Parity:

MSB First

8

None

*Communication Example:

For the VISCA Packet “8x 01 04 07 03 FF”

(CAM_Zoom_Wide), x corresponds with the number and order of the camera in the control chain (daisy chain) where x = 1 for the first camera, x = 2 for the second camera, etc…

COMMAND VISCA COMMENTS COMMAND

SET

Address Set broadcast 88 30 01 FF

IF_Clear broadcast 88 01 00 01 FF

Send Address_set command and IF_clear command before starting communication

ON 8x 01 04 00 02 FF

CAM_Power

OFF

Stop

8x 01 04 00 03 FF

8x 01 04 07 00 FF

ON - Opens Camera Door

OFF - Closes Camera Door

Tele (Std)

Wide (Std)

8x 01 04 07 02 FF

8x 01 04 07 03 FF

CAM_Zoom

Tele (Variable)

Wide (Variable)

8x 01 04 07 2Z FF

8x 01 04 07 3Z FF

Z: Speed Parameter, 2 (Low) to 7 (High)

Direct 8x 01 04 47 0Z 0Z 0Z 0Z FF

ZZZZ: Zoom Data, 0000

Wide to 03ff (Tele)

Stop 8x 01 04 08 00 FF

CAM_Focus

Far

Near

Auto Focus on

8x 01 04 08 01 FF

8x 01 04 08 02 FF

8x 01 04 08 03 FF

Focus Control.

When focus adjusted, change the node to Manual than send Far/Near or Direct command

Manual Focus on 8x 01 04 08 04 FF

CAM_WB

Auto

Indoor mode

Outdoor mode

OnePush mode

8x 01 04 35 00 FF

8x 01 04 35 01 FF

8x 01 04 35 02 FF

8x 01 04 35 03 FF

White Balance Setting.

Indoor/Outdoor: Fixed at

Factory

Pull-in to white with a trigger then hold the data until next trigger

On 8x 01 04 33 02 FF

CAM_Backlight

Off 8x 01 04 33 03 FF

Back light compensation

Gain up to 6 dB max

CAM_Memory

Set

Recall

8x 01 04 3F 01 0Z FF

8x 01 04 3F 02 0Z FF

Preset memory for camera location,

Z=0 to 5. 6 positions total

UP 8x 01 06 01 VV WW 03 01 FF

Down 8x 01 06 01 VV WW 03 02 FF

Pan-Tilt Drive

Left

Right

UpLeft

UpRight

8x 01 06 01 VV WW 01 03 FF

8x 01 06 01 VV WW 02 03 FF

8x 01 06 01 VV WW 01 01 FF

8x 01 06 01 VV WW 02 01 FF

VV: Pan speed 01 to 18

WW: Tilt speed 01 to 14

YYYY: Pan position: approx.

FC90 to 0370 (center 000)

ZZZZ: Tilt position: approx.

FED4 to 012C (center 000)

DownLeft

DownRight

8x 01 06 01 VV WW 01 02 FF

8x 01 06 01 VV WW 02 02 FF

Stop

Absolute Posititon

8x 01 06 01 VV WW 03 03 FF

8x 01 06 01 VV WW

0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

Absolute Drive Position

Home 8x 01 06 04 FF

Returns camera to Home position

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 9 of 14

Inquiry

Command

CARE AND

CLEANING

Inquiry

CAM_Powering

CAM_ZoomPosInq

CAM_FocusAFModeInq

CAM_FocuPosInq

CAM_BacklightModeInq

Pan-tiltPosInq

Packet Inquiry

8x 09 04 00 FF

8x 09 04 47 FF

8x 09 04 38 FF

8x 09 04 48 FF

8x 09 04 33 FF

8X09 06 12 FF

Packet Reply

Y0 50 02 FF

Y0 50 03 FF

Y0 50 0Z 0Z 0Z 0Z FF

Y0 50 02 FF

Y0 50 03 FF

Y0 50 0Z 0Z 0Z 0Z FF

Y0 50 02 FF

Y0 50 03 FF

Y0 50 0W 0W 0W 0W 0Z

0Z 0Z 0Z FF

Description

On

Off

ZZZZ: position

Auto

Manual

ZZZZ: position

On

Off

WWWW: pan

ZZZZ: tilt

OPERATING

AND STORAGE

CONDITIONS

Do not attempt to take the camera module apart (other than for the reasons stated in the manual). There are no user-serviceable components inside.

• Do not spill liquids onto the camera

• Keep this device away from food and liquid

• Avoid touching the lens

• For smears or smudges, clear any dust with a blower and wipe stains with a glass cleaner and clean, soft cloth.

• To clean exterior of camera, wipe with a clean soft cloth. Do not use any abrasive chemicals.

Do not store or operate the WallVIEW 50i PTZ HideAway under the following conditions for any circumstance:

• Temperatures above 40°C (104°F)

• Temperatures below 0°C (32°F)

• High humidity, condensing or wet environments environments

• In inclement weather

• Under severe vibration

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 10 of 14

SPECIFICATIONS

Optics

Imaging

Video

Mechanical

Regulation

Other

Lens Configuration:

Focal Length & F #:

Nine (9) groups of Eleven (11) lens

3.5mm to 91mm; F1.6 to F4.0

Zoom:

Focus

Marginal Illumination Ratio:

26x (at infinite) optical, 12x digital, 312x total

Wide

30% over

Imaging Sensor:

Pixels:

¼” Color CCD

NTSC

Color Separating System:

Electronic Shutter Speed:

PAL - 740K total (400K effective)

Secondary Mosaic Filter System

NTSC 1/80,000 - 1/60 – 1/1 sec

PAL 1/80,000 – 1/50 – 1/1 sec

Minimum Illumination:

Color System:

Luminance Signal S/N Ratio”

1 Lux (visible light mode, 1.30 electric shutter speed)

NTSC or PAL (depending on country of use)

48 dB

Horizontal Resolution:

Scanning System:

Balance:

460 TV Lines

Interlace

Auto/Manual

Focus:

Pan Angle Range: +/-100°

Tilt Angle Range: +90° (+30° default) / -30°

(9)

Physical I/O

Camera Module: 3 – RJ-45 jacks (Power/Video, RS-232 In & Out)

Quick-Connect Box: RJ-45 from Camera Module

RCA-F

4-Pin Din - F for S-Video Output

Round Power Receptacle for 15V Input

Voltage of Operation:

Power Consumption:

Power Supply:

15 VDC (with AC adapter)

12 W (door opening)

100V– 240V Switcher

Operating Temperature:

Safety:

Between 32°F (0°C) and 104°F (40°C)

Integrated NoPinch™ safety mechanism for automatic stop of door opening or closing when

Dimensions: an obstruction is detected

Mounting

Box 9.125” H x 6.375” W x 4” D (23.2 x 16.2cm x 10.1cm)

Opening: 9-3/16” H x 6-3/8” W (23.34cm x 16.2cm)

)

Surrounding Trim Ring 12” H x 12” W (30.38cm x 30.48cm)

Weight: Approx. 5.5 lbs. (2.5 kg)

Supplied Accessories: Canon WL-V5 Multifunction IR Remote

EZCamera Control Adapter

EZCamera Quick-Connect Box

15 VDC Power Supply and Cable

One (1) 15’/(1.46m) S-Video Cable

One (1) 15’/(1.46m) Composite Video Cable

Installation and User Guide

Mounting template and mounting hardware

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 11 of 14

WARRANTY

INFORMATION

Hardware* Warranty One year limited warranty on all parts. Vaddio warrants this product against defects in materials and workmanship for a period of one year from the day of purchase if Vaddio receives notice of such defects during the warranty. They will, at its option, repair or replace products that prove to be defective.

Exclusions - The above warranty shall not apply to defects resulting from: improper or inadequate maintenance by the customer, customers applied software or interfacing, unauthorized modifications or misuse, operation outside the normal environmental specifications for the product, use of the incorrect power supply, or improper site operation and maintenance.

Vaddio Customer service – Vaddio will test, repair, or replace the product or products without charge if the unit is under warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor charge will be estimated by a technician and confirmed by the customer prior to repair. All components must be returned for testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.

Vaddio Technical support - Vaddio technicians will determine and discuss with the customer the criteria for repair costs and/or replacement. Vaddio Technical

Support can be contacted through one of the following resources: e-mail support at [email protected]

or online at www.vaddio.com

.

Return Material Authorization (RMA) number - Before returning a product for repair or replacement request an RMA from Vaddio’s technical support. Provide a technician with a return phone number, e-mail address, shipping address, and product serial numbers. Describe the reason for repairs or returns as well as the date of purchase. Include your assigned RMA number in all correspondence with Vaddio. Write your assigned RMA number on the outside of the box when returning the product.

Voided warranty – The warranty does not apply if the original serial number has been removed or if the product has been disassembled or damaged through misuse, accident, modifications, or unauthorized repair.

Shipping and handling - Vaddio will not pay for inbound shipping transportation or insurance charges or accept any responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and insurance charges all items under warranty but will not assume responsibility for loss and/or damage by the outbound freight carrier.

• If the return shipment appears damaged, retain the original boxes and packing material for inspection by the carrier. o

Contact your carrier immediately.

Products not under warranty - Payment arrangements are required before outbound shipment for all out of warranty products.

*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices.

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 12 of 14

FCC Part 15/ICES-003 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules and Industry Canada ICES-003.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a Commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by Vaddio could void the user's authority to operate the equipment.

European Compliance

This equipment has been approved in accordance with Council Directive 1999/5/EC

"Radio Equipment and Telecommunications Equipment". Compliance of the equipment with the Directive is attested by the application of the CE mark on the equipment.

EC Declaration of Conformity

Application of Council Directive(s):

Manufacturer's Name:

Manufacturer's Address:

1999/5/EC Radio equipment and

Telecommunications Terminal Equipment

(R&TTE) Directive

Vaddio, A Division of Photo Control

4800 Quebec Avenue North.

Minneapolis, MN 55428 USA

WallVIEW

Number:

Standard(s) to which Conformity is declared:

89/336/EEC "Electromagnetic Compatibility (EMC) Directive":

EN 61000-3-2:1995/A1/A2: 1998

EN 61000-3-3:1995

EN 55024: 1998 (Immunity)

EN 61000-4-2: 1995/A1: 1998

EN 61000-4-3: 1996/A1: 1998

EN 61000-4-4: 1995

EN 61000-4-5: 1995

EN 61000-4-6: 1996

EN 61000-4-11: 1994

Specification for limits and methods of measurement of radio interference characteristics of information technology equipment

Part 3: Limits - Section 2: Limits for harmonic current emissions.

Section 3: Limitation of voltage fluctuations and flicker in low voltage supply systems for equipment with rated current up to and including 16 A

Information technology equipment – Immunity characteristic

Limits and methods of measurement

Electrostatic Discharge

Radiated RF Immunity

Electrical Fast Transients

Lighting Surge

Conducted RF Immunity

Voltage Dips and Voltage Interruptions

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 13 of 14

9433 Science Center Drive, New Hope, MN 55428

Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com

©2006 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. CeilingVIEW, WallVIEW, EZCamera, Quick-Connect and PowerRite are registered trademarks of Vaddio,

Inc. All other trademarks are property of their respective owners. Document 341-141 Rev. C.

WallVIEW 50i HideAway – Document 341-141 Rev. C Page 14 of 14

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement