Motorola MBP20 User`s guide

User’s Guide
MBP20
Baby Monitor
The features described in this user's
guide are subject to modifications
without prior notice.
Welcome...
to your new Motorola Baby Monitor!
Thank you for purchasing the MBP20. Now you can see and hear your baby sleeping in another room or you can
monitor your older children in their play room.
Please retain your original dated sales receipt for your records. For warranty service of your Motorola product, you
will need to provide a copy of your dated sales receipt to confirm warranty status. Registration is not required for
warranty coverage.
For product-related questions, please call:
US and Canada
1-888-331-3383
On the Web: www.motorola.com
This User's Guide provides you with all the information you need to get the
most from your product.
Before you can use the baby monitor, you MUST insert the battery in the parent
unit, and we recommend you fully charge the battery so that it continues to
work if you disconnect it from the mains power to carry it to another location.
Please read the Safety Instructions on page 8 before you install the units.
Got everything?
•
•
•
•
•
•
•
1 x Parent unit (MBP20PU)
1 x Baby unit (MBP20BU)
1 x Rechargeable Ni-MH battery pack for the Parent unit
1 x Belt clip / stand for parent unit (already attached)
1 x Battery door for parent unit (already attached)
1 x Power adapter for the parent unit
1 x Power adapter for the baby unit
Overview of your Parent unit
1
9
8
7
2
3
5
3
UP / Volume +
In idle mode: Press to increase the speaker volume.
In menu mode: Press to move up the menu list.
4
Menu / OK
In idle mode: Press to access the main menu.
In menu mode: Press to access the sub-menu, or
confirm the settings.
5
DOWN / Volume In idle mode: Press to decrease the speaker volume.
In menu mode: Press to move down the menu list.
6
Talk
Press and hold to talk back through the baby unit.
Release to quit the talk mode.
7
Video On / Off
Press to deactivate/activate the video feed and turn
on/off the LCD display.
8
Power / Back
In idle or menu mode: Press and hold to power on/off
the parent unit.
In menu mode: Press to cancel settings or go back to
the previous level.
9
Charging Indicator
On steadily when in charging mode.
4
6
1
LCD Display
2
Link Indicator
On when the parent unit is powered on and linked to
the baby unit.
Flashes when the parent unit is out of range of the
baby unit.
Off when the parent unit is powered off.
Flashes when low battery is detected.
NOTE
Off if the battery pack is not installed, even if the
power adapter is connected.
Parent Unit Display
Icons
Indicates when parent unit or baby unit is playing
lullaby.
Behaviors Description
Indicates the signal strength between baby
unit and parent unit. The more blocks, the
stronger connection signal.
Flashes when parent unit is out of range.
Indicates no connection between the baby unit
and parent unit.
Indicates when speaker of parent unit is muted.
Indicates the speaker volume level of parent unit.
Indicates when timer alarm is activated.
Indicates when the sound alert is set on.
Low battery, needs charging.
1/2 battery level. More internal bars mean high
battery level.
Full battery level.
Animation in cycle. Battery is in
charging.
Menu Structure of the Parent Unit
MAIN MENU
SUB MENU
LANGUAGE
English
Français
Español
Deutsch
Italiano
Português
TIMER
Activation
Set Timer
BRIGHTNESS
Level 1 ~ 5
SOUND ALERT
On
Off
ALERT TONES
Low Battery
No Link
RESET
Overview of your Baby unit
10
1
1
2
3
9
5
8
7
4
6
Infrared Light
4 x Infra-red LEDs for night vision illumination
2 Camera Lens
3 Power Indicator
On when the baby unit is switched on.
Off when the baby unit is switched off.
4 UP / Volume +
Press to increase the speaker volume.
5 Power
Press and hold to power on/off the baby unit.
6 DOWN / Volume Press to decrease the speaker volume.
7 Stop
Press to stop the lullaby playing.
8 Play
Press to start playing the selected lullaby.
9 Lullaby
Press to start playing the selected lullaby.
During lullaby playing, press to select and play the
other lullabies.
10 Photo sensor
Light sensor to detect when night vision required.
Important guidelines for installing your Baby Monitor
•
To use your baby unit and parent unit together, you must be able to establish a radio link between them, and the range
will be affected by environmental conditions.
•
Any large metal object, like a refrigerator, a mirror, a filing cabinet, metallic doors or reinforced concrete, between the
baby and parent unit may block the radio signal.
•
The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical equipment, such
as TV's, computers, cordless or mobile phones, fluorescent lights or dimmer switches.
•
If the signal is poor, try moving the parent and/or the baby unit to different positions in the rooms.
1. SAFETY INSTRUCTIONS ................................... 8
2. GETTING STARTED............................................ 9
2.1 Baby unit power supply.......................................9
2.2 Parent unit battery installation.............................9
2.3 Belt clip on parent unit ......................................10
3. USING YOUR BABY MONITOR........................ 11
3.1 Power on/off the parent unit..............................11
3.2 Power on/off the baby unit ................................11
3.3 Adjust speaker volumes of the parent unit
and baby unit ....................................................11
3.4 Talk Back ..........................................................11
3.4.1 Adjust talk back volume .........................12
3.5 Temperature .....................................................12
3.6 Lullaby...............................................................12
3.7 Monitoring management for multi-parent
system...............................................................12
5. DISPOSAL OF THE DEVICE
(ENVIRONMENT)............................................... 15
6. CLEANING......................................................... 16
7. TROUBLESHOOTING ....................................... 16
8. GENERAL INFORMATION................................ 18
9. TECHNICAL SPECIFICATIONS........................ 22
4. Parent unit settings .......................................... 13
4.1 Set the language...............................................13
4.2 Timer.................................................................13
4.2.1 Turn on the timer ...................................13
4.2.2 Set the timer ..........................................14
4.3 Set the brightness .............................................14
4.4 Sound alert........................................................14
4.5 Alert tones.........................................................14
4.6 Reset.................................................................15
7
1. SAFETY INSTRUCTIONS
WARNING:
STRANGULATION HAZARD - Keep the adapter cord
out of the baby's reach.
NEVER place the baby monitor or its cord within the crib.
Secure the cord well away from the baby's reach.
Never use extension cords with AC Adapters. Only use
the AC Adapters provided.
CAMERA SET UP & USE:
• Determine a location for the CAMERA that will provide
the best view of your baby in the crib.
• Place the CAMERA on a flat surface, such as a dresser,
bureau, or shelf, or wall-mount it securely using the
keyhole slots in the base.
• NEVER place the camera or cords within the crib.
• Secure the cord to the wall to keep it away from the
baby’s reach.
This baby monitor is compliant with all relevant standards
regarding electromagnetic fields and is, when handled as
described in the User's Guide, safe to use. Therefore,
always read the instructions in this User's Guide carefully
before using the device.
8
• Adult assembly is required. Keep small parts away from
children when assembling.
• This product is not a toy. Don't allow children to play
with it.
• This baby monitor is not a substitute for responsible
adult supervision.
• Keep this User's Guide for future reference.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adapters. Only
use the power adapters provided.
• Test this monitor and all its functions so that you are
familiar with it prior to actual use.
• Do not use the baby monitor near water.
• Do not install the baby monitor near a heat source.
• Only use the chargers and power adapters provided. Do
not use other chargers or power adapters as this may
damage the device and battery pack.
• Only insert a battery pack of the same type.
• Do not touch the plug contacts with sharp or metal
objects.
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Use only a battery pack with rating: 2.4V 600mAh.
SAFETY INSTRUCTIONS
2. GETTING STARTED
2.1
Baby unit power supply
2.2
Parent unit battery installation
A rechargeable battery pack is supplied and MUST be
fitted in the parent unit in order for the parent unit to work.
Charge the parent unit before you use it for the first time or
when the parent unit indicates that the battery is low.
DC SOCKET
DC PLUG
Battery
SOCKET
Battery PLUG
1. Insert the DC plug of the power adapter with smaller
DC plug into the DC socket in the side of the baby unit,
as shown.
2. Connect the other end of the power adapter to a
suitable mains power outlet.
NOTE
Only use the provided power adapter.
GETTING STARTED
1. Take off the belt clip / stand.
2. Slide off the battery compartment cover.
9
3. Insert the plug of the battery pack into the socket inside
the battery compartment, and fit the battery pack into
the compartment.
2.3
Belt clip on parent unit
4. Replace the battery compartment cover, and reinstall
the belt clip / stand (refer to section 2.3).
5. Insert the DC plug of the power adapter with the larger
DC plug into the DC socket in the side of the parent unit.
6. Connect the other end of the power adapter to a
suitable mains power outlet.
7. The Charging Indicator comes on.
NOTE
Only use the provided power adapter.
1. The belt clip/stand attaches to the back of the parent
unit and clips into the locking slots on each side.
2. The unit comes with the accessory fitted in belt clip
mode.
3. You can convert it into stand mode by pulling the clip
out slightly and then rotating it by half a turn, as shown.
10
GETTING STARTED
3. USING YOUR BABY MONITOR
3.3
Please read these instructions carefully, and be aware that
this baby monitor is only intended as an aid. It is not a
substitute for responsible, correct parental supervision.
There are 5 volume levels on the baby unit, and 6 levels on the
parent unit, including VOLUME OFF. The volume level of parent unit
will be shown on the status bar when you adjust the volume.
3.1
Power on/off the parent unit
1. When the parent unit is off, press and hold 3 until the
Link Indicator is on. The parent unit is now powered
on and will search for and link itself to the baby unit.
2. When the parent unit is on, press and hold 3 until the
Link Indicator turns off. The parent unit is now
powered off, although the display may take a few
seconds to go off fully.
3.2
Power on/off the baby unit
1. When the baby unit is off, press and hold 0 until the
Power Indicator is on. The baby unit is now powered on.
2. When the baby unit is on, press and hold 0 until the
Power Indicator turns off. The baby unit is now powered
off.
NOTE
Do not place the parent and baby units too close together,
or you may hear a high pitched noise. This is not a fault.
The units are designed to be operated at some distance
apart, e.g. in separate rooms.
USING YOUR BABY MONITOR
Adjust speaker volumes of the parent
unit and baby unit
1. Press + or - on the parent unit or > or < on
the baby unit to adjust the respective volume level.
2. The
will be displayed if the volume of the parent unit
is turned off.
An audible alert is emitted if you try to adjust beyond
the highest or lowest volume level.
Changing the volume setting on the baby unit affects the
volume at the baby unit when you use the Talk Back
feature or when playing a lullaby.
3.4
Talk Back
You can use the Talk Back feature to comfort and reassure
your baby.
Whilst using Talk Back you will not be able to hear your
baby until you release the button.
1. Press and hold 7 on the parent unit to speak to your
baby. Talk will be displayed on the parent unit.
2. Release to hear your baby again.
11
3.4.1
Adjust talk back volume
The baby unit has 5 volume levels from Level 1 to Level 5.
Press > or < on the baby unit to increase or decrease
the volume respectively.
NOTE
If a lullaby is playing, it will stop during Talk Back, but will
restart from the beginning when the Talk Back ends.
3.5
Temperature
The baby unit constantly monitors the temperature in your
baby's room and alerts you if it gets lower than 14ºC (or
57ºF), by emitting a warning beep and showing the alert
message "Too cold!" on the parent unit screen, or if it gets
higher than 39ºC (or 102ºF), it will show "Too hot!".
Although this is for reference only, and there may be a
small difference between the baby monitor reading and the
actual temperature, please check your baby immediately if
such an alert message is triggered.
Note
The current temperature at the baby unit is shown on the
parent unit status bar whenever it is displayed.
12
3.6
Lullaby
There are 3 lullabies available to play for your baby, either
repeating one melody or repeating through all three
melodies.
1. Press 2 on the baby unit to select the lullaby and
start playing.
2. During playback, press 2 to step between different
lullabies.
OR
Press 8 on the baby unit to start playing the selected
lullaby.
3. During playback, press 9 to stop playing.
3.7
Monitoring management for multiparent system
The system allows pairing up to two parent units to a baby
unit. However, only one parent unit can receive video
image at a time. You can switch the video feed between
these two parent units.
The first powered up parent unit will connect to the baby
unit automatically, and the next powered up parent unit will
turn up on screen ANOTHER PU IS VIDEO MONITORING! for around 30
seconds and then goes blank. Press once the 6 to turn
off the screen.
USING YOUR BABY MONITOR
NOTE
The parent unit still carries on audio monitoring even if the
video capture is turned off.
4. Parent unit settings
4.1
Set the language
1. Press 1 to access the main menu.
To switch the video feed from the current monitoring parent
unit to the other parent unit which is not in video monitoring
mode:
2. Press + or - to select LANGUAGE.
1. Press 6 on the current video monitoring parent unit,
the screen will be blank without video image received.
4. Press + or - to select the desired language.
2. Press 6 on the other parent unit which is NOT in
video monitoring mode, the video feed will be
transferred to that parent unit.
4.2
3. Press 1 to enter the sub-menu.
5. Press 1 to confirm.
Timer
The timer function serves as an alarm to remind you of
things-to-do for the baby such as feeding, or medication.
4.2.1
Turn on the timer
1. Press 1 to access the main menu.
2. Press + or - to select TIMER.
3. Press 1 to enter the sub-menu.
4. Press + or - to select ACTIVATION.
5. Press 1 and then + or - to select ON or OFF.
6. Press 1, and then if ON was selected, press + or to select the timer mode
7. Press 1 to confirm.
Parent unit settings
13
4.2.2
Set the timer
1. Repeat steps 1 to 3 in section 4.2.1.
2. Press + or - to select SET TIMER.
3. Press 1 and then set the number of hours (00 to 12)
using the + or - keys.
4. Press 1 and then set the number of minutes (00 to 59)
using the + or - keys.
5. Press 1 to confirm.
NOTE
When the timer period is reached, the unit will emit an alert
beep and 00:00 on the screen. You can press any button
to stop the beeps. If the timer mode was set to ONCE, the
timer will be cancelled, but if set to REPEATED, it will reset and
start another timer period.
4.3
Set the brightness
1. Press 1 to access the main menu.
2. Press + or - to select BRIGHTNESS.
3. Press 1 to enter the sub-menu to set the brightness level.
4. Press + or - to select from LEVEL 1 to LEVEL 5. The
screen brightness changes as the options are selected.
5. Press 1 to confirm.
NOTE
A lower brightness level will reduce the power consumption.
14
4.4
Sound alert
When the sound alert is set ON, and the parent unit speaker
volume is off, it will cause the parent unit to beep and flash
"Sound alert" on the display, whenever the sound at the
baby unit goes above a preset threshold.
1. Press 1 to access the main menu.
2. Press + or - to select SOUND ALERT.
3. Press 1 to enter the sub-menu.
4. Press + or - to select ON or OFF.
5. Press 1 to confirm.
4.5
Alert tones
You can set the parent unit to give a warning when the
battery is low and/or if the radio link to the baby unit is lost.
When activated, an alert screen will be displayed on the
parent unit with an alert tone emitted simultaneously.
1. Press 1 to access the main menu.
2. Press + or - to select ALERT TONES.
3. Press 1 and + or - to select LOW BATTERY or NO LINK.
4. Press 1 and + or - to select ON or OFF for the alert
tone.
5. Press 1 to confirm.
Parent unit settings
4.6
Reset
You can restore all the adjustable settings back to their
original factory settings.
1. Press 1 to access the main menu.
2. Press + or - to select RESET.
3. Press 1 to display CONFIRM?.
4. Press 1 to confirm the reset.
5. DISPOSAL OF THE DEVICE
(ENVIRONMENT)
At the end of the product lifecycle, you should
not dispose of this product with normal
household waste. Take this product to a
collection point for the recycling of electrical
and electronic equipment. The symbol on the
product, user's guide and/or box indicates this.
Some of the product materials can be re-used if you take
them to a recycling point. By reusing some parts or raw
materials from used products you make an important
contribution to the protection of the environment.
Please contact your local authorities in case you need
more information on the collection points in your area.
Dispose of the battery pack in an environmentally-friendly
manner according to your local regulations.
DISPOSAL OF THE DEVICE (ENVIRONMENT)
15
6. CLEANING
7. TROUBLESHOOTING
Clean your MBP20 with a slightly damp cloth or with an
anti-static cloth. Never use cleaning agents or abrasive
solvents.
Link light on the parent unit does not come on
Cleaning and care
• Do not clean any part of the product with thinners or
other solvents and chemicals - this may cause
permanent damage to the product which is not covered
by the warranty.
• Keep your MBP20 away from hot, humid areas or
strong sunlight, and do not let it get wet.
• Every effort has been made to ensure high standards of
reliability for your MBP20. However, if something does
go wrong, please do not try to repair it yourself - contact
Customer Service for assistance.
• Check whether the parent unit is powered on.
• Check whether the supplied battery pack is correctly
installed and that they are not drained.
• Recharge the battery in the parent unit by connecting it
to the power supply.
Link light on the parent unit flashes
• The parent unit and the baby unit may be out of range
with each other. Reduce the distance between the units,
but not closer than 5 feet.
• The baby unit may be switched off. Press and hold the
0 key on the baby unit to switch on the baby unit.
Low battery light or
flashes
on the parent unit screen
• Battery pack in the parent unit is running low. Connect
the parent unit to the mains power with the supplied
power adaptor for recharging.
The parent unit beeps
• Lost connection with the baby unit. Reduce the distance
between the parent unit and the baby unit, but not
closer than 5 feet.
• The baby unit may be switched off. Press and hold the
0 key on the baby unit to switch on the baby unit.
16
CLEANING
• Battery pack in parent unit may be running low. Connect
the parent unit to the mains power with the supplied
power adaptor for recharging.
Cannot view the video image of baby from the
parent unit
• Video feed maybe turned off. Activate the video feed by
pressing 6.
• The parent unit and the baby unit may be out of range
with each other. Reduce the distance between the units,
but not closer than 5 feet.
• Battery pack in parent unit may be drained. Connect the
parent unit to the mains power with the supplied power
adaptor for recharging.
Cannot hear sound or baby cry from the parent unit
• The volume level in the parent unit may be set too low,
increase the volume level of the parent unit. Refer to
section 3.3 for volume level settings.
• The parent unit and the baby unit may be out of range
with each other. Reduce the distance between the units,
but not closer than 5 feet.
TROUBLESHOOTING
The baby monitor system produces a high-pitched
noise
• The parent unit and the baby unit are too close to each
other. Make sure the parent unit and baby unit are at
least 5 feet away from each other.
• The speaker volume of the parent unit maybe set too
high. Decrease the volume of the parent unit.
Battery pack in the parent unit is running low
quickly
• The brightness level of the parent unit screen may be
set too high, which consumes more power. Reduce the
brightness level of the screen - see section 4.3.
• The volume level of the parent unit may be set too high
which consumes power. Decrease the volume level of
the parent unit. Refer to section 3.3 for volume level
settings.
Talk back feature is not working
• Make sure the baby unit is powered on, and the link
between the parent unit and baby unit is normal.
• Check that the volume is loud enough at the baby unit,
refer to section 3.4.
17
8. GENERAL INFORMATION
If your product is not working properly...
1. Read this User's Guide.
2. Visit our website: www.motorola.com
3. Contact Customer Service at
US and Canada 1-888-331-3383
To order a replacement battery pack for the parent unit,
contact customer service.
Consumer Products and Accessories
Limited Warranty ("Warranty")
Thank you for purchasing this Motorola branded product
manufactured under license by Binatone Electronics
International LTD ("BINATONE").
What Does this Warranty Cover?
Subject to the exclusions contained below, BINATONE
warrants that this Motorola branded product ("Product") or
certified accessory ("Accessory") sold for use with this
product that it manufactured to be free from defects in
materials and workmanship under normal consumer usage
for the period outlined below. This Warranty is your
exclusive warranty and is not transferable.
Who is covered?
This Warranty extends only to the first consumer
purchaser, and is not transferable.
18
What will BINATONE do?
BINATONE or its authorized distributor at its option and
within a commercially reasonable time, will at no charge
repair or replace any Products or Accessories that does not
conform to this Warranty. We may use functionally
equivalent reconditioned/ refurbished/ pre-owned or new
Products, Accessories or parts.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR
OR REPLACEMENT PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO
EVENT SHALL MOTOROLA OR BINATONE BE LIABLE,
WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT OR ACCESSORY,
OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS
OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS
OF INFORMATION OR OTHER FINANCIAL LOSS
ARISING OUT OF OR IN CONNECTION WITH THE
GENERAL INFORMATION
ABILITY OR INABILITY TO USE THE PRODUCTS OR
ACCESSORIES TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
Some jurisdictions do not allow the limitation or exclusion
of incidental or consequential damages, or limitation on the
length of an implied warranty, so the above limitations or
exclusions may not apply to you. This Warranty gives you
specific legal rights, and you may also have other rights
that vary from one jurisdiction to another.
Products Covered Length of Coverage
Consumer
Products
One (1) year from the date of the
products original purchase by the first
consumer purchaser of the product.
Consumer
Accessories
Ninety (90) days from the date of the
accessories original purchase by the
first consumer purchaser of the
product.
Consumer
Products and
Accessories that
are Repaired or
Replaced
The balance of the original
warranty or for ninety (90) days
from the date returned to the
consumer, whichever is longer.
GENERAL INFORMATION
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are
excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak
are covered by this Warranty.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or
neglect, such as physical damage (cracks, scratches, etc.)
to the surface of the product resulting from misuse; (b)
contact with liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or food; (c)
use of the Products or Accessories for commercial
purposes or subjecting the Product or Accessory to
abnormal usage or conditions; or (d) other acts which are
not the fault of MOTOROLA or BINATONE, are excluded
from coverage.
Use of Non-Motorola branded Products and
Accessories. Defects or damage that result from the use
of Non-Motorola branded or certified Products or
Accessories or other peripheral equipment are excluded
from coverage.
19
Unauthorized Service or Modification. Defects or
damages resulting from service, testing, adjustment,
installation, maintenance, alteration, or modification in any
way by someone other than MOTOROLA, BINATONE or
its authorized service centers, are excluded from coverage.
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or
parts, are excluded from coverage.
To obtain service, you must include: (a) the Product or
Accessory; (b) the original proof of purchase (receipt)
which includes the date, place and seller of the Product; (c)
if a warranty card was included in your box, a completed
warranty card showing the serial number of the Product; (d)
a written description of the problem; and, most importantly;
(e) your address and telephone number.
Communication Services. Defects, damages, or the
failure of Products or Accessories due to any
communication service or signal you may subscribe to or
use with the Products or Accessories is excluded from
coverage.
These terms and conditions constitute the complete
warranty agreement between you and BINATONE
regarding the Products or Accessories purchased by you,
and supersede any prior agreement or representations,
including representations made in any literature
publications or promotional materials issued by
BINATONE or representations made by any agent,
employee or staff of BINATONE, that may have been made
in connection with the said purchase.
How to Obtain Warranty Service or Other
Information?
FCC, ACTA and Industry Canada (IC)
Regulations
To obtain service or information, please call:
US and Canada
1-888-331-3383
You will receive instructions on how to ship the Products or
Accessories at your expense and risk, to a BINATONE
Authorized Repair Center.
20
Warning: Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
GENERAL INFORMATION
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
This Class B digital apparatus complies with Canadian
ICES-003
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Caution: To maintain the compliance with the FCC's RF
exposure guideline, place the baby unit at least 20 cm from
nearby persons.
For body worn operation, the parent unit has been tested
and meets the FCC RF exposure guidelines when used
with the belt clip supplied or designated for this product.
Use of other accessories may not ensure compliance with
FCC RF exposure guidelines.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
GENERAL INFORMATION
21
9. TECHNICAL SPECIFICATIONS
Parent Unit :
Baby Unit:
Frequency
1921.536 MHz - 1928.448 MHz
Channels
5
Operating
temperature
5ºC - 45ºC
Frequency
1921.536 MHz - 1928.448 MHz
Channels
5
Operating
temperature
5ºC - 45ºC
Image sensor
Color CMOS 30M Pixels
Lens
f 3.6mm, F 2.4
IR LED
4 pcs
Baby unit voltage
100 - 240V
(AC voltage, 50/60Hz)
Baby unit voltage
(Adapter output)
22
6VDC @600mA
Display
1.5" CSTN LCD
Display colour
65K color LCD
Brightness control
5 steps
Parent unit voltage
2.4V 600mAh Ni-MH battery pack
Parent unit voltage
100 - 240V
(AC voltage, 50/60Hz)
Parent unit voltage
6VDC @600mA
(Adapter output)
TECHNICAL SPECIFICATIONS
Manufactured, distributed or sold by Binatone
Electronics International LTD., official licensee
for this product. MOTOROLA and the Stylized
M Logo are trademarks or registered
trademarks of Motorola Trademark Holdings,
LLC. and are used under license. All other
trademarks are the property of their respective
owners.
© 2011 Motorola Mobility, Inc. All rights
reserved.
Version 2.0
Printed in China