Emerson CF620AP00 Owner`s manual

READ AND SAVE THESE INSTRUCTIONS
™
LAGUNA BAY
52” Wet Location
Ceiling Fan Owner's Manual
Model Numbers
CF620AP00
CF620AW00
CF620VNB00
Net Weight:
Part No. F40BP74450000
18.8
Lbs.
Fan Blades
Not Included
Form No. BP7445
U.L. Model No.: CF620
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must be in accordance with the National Electrical Codes “ANSI/NFPA 70-2008” and
Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling
fan must be grounded as a precaution against possible electrical shock. Electrical installation
should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting at least
50 pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support of 22.7 kg. (50 lbs.)
or less”, and use the mounting screws provided with the outlet box. Most outlet boxes commonly
used for support of light fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
4. The downrod furnished with the fan provides the minimum recommended floor to fan blade
clearance for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do
not know enough about electrical wiring, have your fan installed by a licensed electrician.
NOTE: All setscrews must be checked and re-tightened where necessary before installation.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use with this product by Emerson Electric Co. Substitution
of parts or accessories not designated for use with this product by Emerson Electric Co. could
result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
WARNING: To reduce the risk of electrical shock, this fan must be installed with an isolating wall
control/switch.
NOTE: This fan is suitable for use in wet locations when installed in a GFCI protected branch circuit.
THIS FAN IS SUITABLE FOR WET LOCATIONS
SUCH AS COVERED PORCHES, COVERED PATIOS, AND COVERED DECKS...
ANYWHERE THERE IS A ROOF OVERHEAD.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2
U.L. Model No.: CF620
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Installed Wire Length
Up to 50 ft.
50-100 ft.
Tools Needed for Assembly
One Phillips head screwdriver
One 1/4” blade screwdriver
One stepladder
One wire stripper
WARNING
!
MATERIALS
Wire Size A.W.G.
14
12
Before assembly your ceiling fan, refer to section
on proper method of wiring your fan (page 9).
If you feel you do not have enough wiring
knowledge or experience, have your fan installed
by a licensed electrician.
Wiring outlet box and box connectors must be of
type required by the local code. The minimum wire
would be a 3-conductor (2-wire with ground) of the
following size:
Unpacking Instructions
!
NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
2. Remove and discard the two cardboard shipping
retainers securing the motor hub in the motor
housing assembly.
3. Remove the fan motor assembly from the
protective plastic bag. Place all carton contents on
a protective surface.
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description,
refer to exploded view illustration.
a. Fan motor assembly
b. One hanger bracket
c. One hanger ball/4.5” downrod assembly
d. One ceiling cover
e. One coupling cover
f. Five fan blades flanges
g. One lower housing
h. One switch housing assembly
l. One loose parts bag containing:
1. One clevis pin
2. One hairpin clip
3. Two #8-32 x 1-1/4” threaded studs
4. Two #8 external tooth lockwashers
5. Two #8-32 knurled knobs
6. Twenty-one #10 - 24 x 12mm washer head screws
7. Twenty-one 16mm flat washers
8. One #8 - 32 x 8mm pan head screw
9. One 1/4 - 20 x 14mm pan head screw with
lockwasher
10. One #8 - 32 x 8mm flat head screw
11. Three wire connectors
12. One pendant with pull chain and coupling
13. One balancing kit
A. FAN MOTOR
ASSEMBLY
D. CEILING
COVER
E. COUPLING
COVER
B. HANGER
BRACKET
F. FAN BLADE
FLANGES
C. HANGER BALL/
4.5" DOWNROD
ASSEMBLY
G. LOWER HOUSING
H. SWITCH
HOUSING
ASSEMBLY
I. LOOSE PARTS BAG
3
U.L. Model No.: CF620
Electrical Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
!
!
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
To reduce the risk of fire, electrical shock, or
personal injury, mount fan to outlet box marked
“Acceptable for Fan Support of 22.7 kg. (50 lbs.) or
less”, and use screws supplied with outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
!
WARNING
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
How to Put Your Ceiling Fan Together
!
WARNING
PIN
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
HANGER
BALL
DOWNROD
1. Remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 1). Remove the clevis pin from the
downrod, then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in Step 5.
2. Loosen setscrew in motor coupling if necessary.
Separate, untwist and unkink the three 80” motor
leads. Route the motor lead wires through the
downrod. Align the clevis pin holes in the downrod
with the holes in the motor coupling. Install the
clevis pin and secure with the hairpin clip (Figure
2). The clevis pin must go through the holes in the
motor coupling and the holes in the downrod. Be
sure to push the straight leg of the hairpin clip
through the hole near the end of the clevis pin until
the curved portion of the hairpin clip snaps around
the clevis pin. The hairpin clip must be properly
installed to prevent the clevis pin from working
loose. Pull on the downrod to make sure the clevis
pin is properly installed.
!
SETSCREW
Figure 1
DOWNROD
DOWNROD
HAIRPIN
HAIRPIN
CLIP
CLIP
SETSCREW
(2)
SETSCREW
CLEVIS
PIN
CLEVIS PIN
WARNING
MOTOR
MOTOR
COUPLING
COUPLING
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrews securely
tightened. Failure to verify that the pin and setscrews
are properly installed could result in the fan falling.
Figure 2
4
U.L. Model No.: CF620
How to Put Your Ceiling Fan Together (continued)
3. While pulling up on the downrod, securely tighten
the two setscrews in the motor coupling (Figure 3).
GROMMET
NOTE: The setscrews must be properly installed
as described above, or fan wobble could result.
COUPLING COVER
4. Make sure the grommet is properly installed in the
coupling cover then slide the coupler cover on the
downrod until it rests on the motor housing. Place
the ceiling cover over the downrod. Be sure both
the ceiling cover and the coupler cover are oriented
correctly (Figure 3).
DOWNROD
5. Reinstall the hanger ball (Figure 4) on the downrod as
follows. Route the motor leads through the downrod.
Position the pin through the two holes in the downrod
and align the ball so the pin is captured in the groove
in the top of the hanger ball. Pull the hanger ball up
tight against the pin and securely tighten the setscrew
in the hanger ball. A loose setscrew could create fan
wobble.
!
COUPLING
SETSCREW (2)
Figure 3
WARNING
HANGER BALL
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
DOWNROD
6. The fan comes with blue, black and white leads
that are 80” long. Before installing fan, measure up
approximately 6 to 9-inches above top of hanger
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
PIN
CEILING
COVER
SETSCREW
7. Turn fan motor assembly upside down in
preparation for mounting fan blades. Position the
top and bottom halves of the styrofoam packaging
on end, with solid styrofoam facing outward. Set
side-by-side on the floor with a six to eight-inch gap
between the halves (Figure 5). Carefully place the
partially assembled ceiling fan on the styrofoam
halves, with the hanger ball/downrod assembly
positioned in the gap and the fan motor assembly
resting on top of the styrofoam ends.
Figure 4
PARTIALLY
ASSEMBLED FAN
SOLID
STYROFOAM
FACING OUT
6" - 8"
GAP
Figure 5
5
U.L. Model No.: CF620
How to Put Your Ceiling Fan Together (continued)
8. Remove the shipping spacers and the spacer
attachment screws from the motor before
installation of blade assemblies. Discard the
spacers and spacer screws (Figure 6).
SPACER ATTACHMENT
SCREW
SHIPPING
SPACER
9. Mount blade flanges (supplied with fan) to fan
blades (sold separately) using four #10 - 24 x
12mm washer head screws and four 16mm flat
washers (supplied with fan) (Figure 7).
NOTE: Some accessory blades available are
supplied with shorter screws. These shorter
screws MUST be used to assemble the blades to
flanges.
Figure 6
NOTE: Take care not to scratch fan housing when
installing blades.
10. Loosely attach one blade/flange assembly to the
motor hub by securing the two 1/4 - 20 x 14mm
captive pan head screws. Make sure the screws
are NOT tightened (Figure 8). Repeat this
procedure for other four blade assemblies.
!
#10 - 24 x 12mm WASHER
HEAD SCREW
(4 per blade/flange)
16mm FLAT WASHER
(4 per blade/flange)
FAN BLADE
(Sold Separately)
WARNING
BLADE FLANGE
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
11. Once all five blade/flange assemblies are
secured to the motor hub, proceed to tighten all
the 1/4 - 20 x 14mm captive pan head screws at
this time.
Figure 7
1/4 - 20 x 14mm CAPTIVE
PAN HEAD SCREW (2)
12. Remove one #8 - 32 x 8mm pan head screw
from the lower housing adapter plate (reserve for
later use). Loosen the other two screws to
assemble the lower housing to the lower housing
adapter plate (Figure 9).
BLADE/FLANGE ASSEMBLY (5)
13. Position the lower housing onto the fan motor
assembly, aligning each of the the three holes.
Rotate the lower housing to engage the two
loosened screws in the two key hole slots.
Replace the #8 - 32 x 8mm pan head screw
(removed previously) and tighten all three screws
to secure the lower housing to the lower housing
adapter plate (Figure 9).
Figure 8
LOWER HOUSING
LOWER HOUSING
ADAPTER PLATE
NOTE: Make sure wires are not pinched between
lower housing adapter plate and lower housing.
LOOSEN TWO #8 - 32 x
8mm PAN HEAD SCREWS
REMOVE ONE #8 - 32 x
8mm PAN HEAD SCREW
Figure 9
6
U.L. Model No.: CF620
How to Put Your Ceiling Fan Together (continued)
14. Engage the connector of the switch housing
assembly with the motor connector (Figure 10).
The two connectors are keyed and color-coded
and must be mated correctly (color-to-color)
before they can be engaged. Make sure the
connector latch closes properly (Figure 10).
SWITCH HOUSING
ASSEMBLY
SWITCH HOUSING
ASSEMBLY CONNECTOR
NOTE: Make sure all wires and connector are
tucked under the switch housing assembly and
not pinched between the switch housing
assembly and lower housing.
MOTOR
CONNECTOR
15. Remove the three #8 - 32 x 8mm flat head
screws from the switch housing assembly
(reserve for later use) for assembly of the switch
housing assembly to the lower housing (Figure
11).
Figure 10
16. Position the switch housing assembly onto the
lower housing, aligning each of the the three
holes. Replace the three #8 - 32 x 8mm flat head
screw (removed previously) and tighten all three
screws to secure the switch housing assembly to
the lower housing. (Figure 11).
SWITCH HOUSING
ASSEMBLY
LOWER HOUSING
#8 - 32 x 8mm FLAT
HEAD SCREW (3)
Figure 11
7
U.L. Model No.: CF620
How to Hang Your Ceiling Fan
!
CEILING
WARNING
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 12).
!
WARNING
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of 22.7
kg. (50 lbs.) or less”.
!
AT LEAST
7'
WARNING
FLOOR
To reduce the risk of fire, electrical shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
Figure 12
1.Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box.
(Figure 13.)
NOTE: CEILING COVER
OMITTED FOR CLARITY.
OUTLET
BOX
2. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 13). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 14).
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
HANGER
BRACKET
!
WARNING
TAB
Figure 13
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
!
WARNING
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES
OMITTED FOR CLARITY.
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
!
OUTLET
BOX
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
Figure 14
8
1-1/4" THREADED
STUD (2)
U.L. Model No.: CF620
How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
!
GROUND
WIRE
BLACK
FAN WIRE
BLUE FAN WIRE
LISTED
WIRE
CONNECTOR (3)
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is
grounded, contact a licensed electrician for advice,
as it must be grounded for safe operation.
GREEN WIRE
(GROUND) FROM
HANGER BRACKET
GREEN WIRE
(GROUND) FROM
HANGER BALL
1. Connect the green grounding lead from the hanger
ball and the green grounding lead from the hanger
bracket to the grounding conductor of supply (this
may be a bare wire or wire with green colored
insulation). Securely connect wires with wire
connectors supplied.
Figure 15
WHITE SUPPLY
(NEUTRAL)
WHITE FAN WIRE
BLACK SUPPLY
(HOT)
NOTE: CEILING COVER
OMITTED FOR CLARITY.
NOTE: If you are using an Emerson Light Fixture
with your fan, see Light Fixture Owner’s Manual
for wiring.
2. Securely connect the fan motor white wire to the
supply white (neutral) wire using wire connector
supplied (Figure 15). Securely connect the fan
motor black wire and blue wire to the supply black
(hot) wire using wire connector supplied (Figure
15). After connections have been made, turn leads
upward and carefully push leads into the outlet box,
with the white and green leads on one side of the
outlet box and the blue and black leads on the
other side of the outlet box.
!
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
CEILING COVER
3. Screw the two threaded studs (supplied) into the
tapped holes in the hanger bracket.
THREADED STUDS (2)
LOCKWASHERS (2)
4. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 16).
KNURLED KNOBS (2)
Figure 16
5. Secure the ceiling cover in place by sliding
lockwashers over the threaded studs and installing
the two knurled knobs (supplied). (Figure 16).
Tighten the knurled knobs securely until the ceiling
cover fits snugly against the ceiling and the hole in
the ceiling cover is clear of the downrod. Your fan
is now wired to be turned on and off from the fan
switch.
!
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
9
U.L. Model No.: CF620
Fan Speed and Direction
1. Assembly of the ceiling fan is now complete.
Restore electrical power to the branch circuit at the
fuse box or breaker panel.
2. Connect the fan speed pull chain to the wood
pendant with pull chain. (Figure 17).
FAN SPEED
PULL CHAIN
3. All fans are shipped from the factory with the
reversing switch positioned to circulate air
downward.
PULL CHAIN COUPLING
4. If airflow is desired in the opposite direction, turn
the fan off and wait for the blades to stop turning.
Then slide the reversing switch, located on top of
the fan motor assembly, to the opposite position
(Figure 18) and turn the fan on again. The blades
will turn in the opposite direction and reverse the
airflow.
Season
Summer
Winter
PULL CHAIN
WOOD PENDANT
Figure 17
Reverse Switch Information
Rotation Direction
Switch Position
Counter-Clockwise
Right
Clockwise
Left
FAN SPEED PULL
CHAIN
REVERSE SWITCH
Figure 18
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
!
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
WARNING
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Accessories
1. Ceiling Fan/Light Controls (see store or catalog).
!
2. Downrod Extension Kits (see store or catalog).
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
3. Ceiling Fan Light Kits (see store or catalog).
!
WARNING
WARNING
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
10
U.L. Model No.: CF620
Trouble Shooting
!
WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble shooting your fan.
TROUBLE
1. Fan will not start.
PROBABLE CAUSE
SUGGESTED REMEDY
1. Fuse or circuit breaker blown.
1. Check main and branch circuit fuses or circuit
breakers.
2. Loose power line connections to the fan,
or loose switch wire connections in the
switch housing.
2. Check line wire connections to fan and switch
wire connections in the switch housing.
!
2. Fan sounds noisy.
3. Reversing switch in neutral position.
3. Make sure reversing switch position is all the
way to one side.
1. Blades not attached to fan.
1. Attach blades to fan before operating.
2. Loose screws in motor housing.
2. Check to make sure all screws in motor housing
are snug (not over-tight).
3. Wire connectors inside switch housing
rattling.
3. Check to make sure wire connectors in switch
housing are not rattling against each other or
against the interior wall of the switch housing.
!
3. Fan wobbles
excessively.
WARNING: Make sure main power is
turned OFF.
WARNING: Make sure main power is
turned OFF.
4. Screws holding blades to flywheel
are loose.
4. Tighten screws securely.
1. Setscrew in motor coupling is loose.
1. Tighten both setscrews securely in the motor
coupling.
2. Setscrew in hanger ball/downrod
assembly is loose.
2. Tighten the setscrew in the hanger ball/
downrod assembly.
3. Screws securing fan blades to
flywheel are loose.
3. Check to be sure screws which attach the fan
blades to the motor are tight.
4. Hanger bracket and/or ceiling outlet
box is not securely fastened.
4. Tighten the hanger bracket screws to the outlet
box, and/or secure outlet box.
5. Fan blades out of balance.
5. Interchanging an adjacent (side-by-side) blade
pair can redistribute the weight and result in
smoother operation.
11
U.L. Model No.: CF620
Repair Parts
2
1
3
6
16
15
17
7
8
18
5
4
BLADES SOLD
SEPARATELY
9
10
20
22
11
13
19
21
12
14
12
U.L. Model No.: CF620
Repair Parts Listing
Key
No.
Model Numbers
CF620AWS00 CF620VNB00
Description
CF620AP00
761655-34
761655-21
761655-89
1
2
Hanger Ball Assembly,
Consisting of:
Hanger Bracket
Hanger Ball
—
—
—
—
—
—
3
Downrod (4.5”)
—
—
—
*
4
5
6
7
8
Parts Bag Containing:
Pin, Clevis (1)
Clip, Hairpin (1)
Threaded Stud, #8 - 32 x 1-1/4” (2)
Lockwasher, External Tooth #8 (2)
Knurled Knob, #8 - 32 (2)
764208
—
—
—
—
—
764208-1
—
—
—
—
—
764208
—
—
—
—
—
9
Screw, Washer Head, #10 - 24 x 12mm (21)
—
—
—
10
11
12
Flat Washer, 16mm (21)
Screw, Pan Head, #8 - 32 x 8mm (1)
Screw, Flat Head, #8 - 32 x 8mm (1)
—
—
—
—
—
—
—
—
—
13
Screw, Pan Head, 1/4 - 20 x 14mm with Lockwasher (1)
—
—
—
14
15
16
Pendant with Pull Chain and Coupling (1)
Wire Connector (3)
Balancing Kit (1)
—
—
—
—
—
—
—
—
—
17
Canopy, Ceiling (1)
764199-AP
764199-AW
764199-VNB
18
19
20
21
Motor Coupling Cover (1)
Wiring Harness (1)
Lower Housing (1)
Switch Housing (1)
764032-AP
764204
764203-AP
764207-AP
764032-AW
764204-1
764203-AW
764207-AW
764032-VNB
764204
764203-VNB
764207-VNB
22
Blade Flanges (set of 5)
764205-AP
764205-AW
764205-VNB
—
Owner's Manual
BP7445
BP7445
BP7445
*
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION •
NAME OF ITEM •
MODEL NUMBER
For repair parts, phone 1-800-654-3545.
13
U.L. Model No.: CF620
Notes
14
U.L. Model No.: CF620
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in
workmanship and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for the lifetime of your ceiling fan. All other components and accessories are
covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND
ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at
no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can
be provided, Emerson will refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED PRODUCT OR
REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OR REMOVAL, REINSTALLATION
AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR
RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service
center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort
Products, Division of Emerson Electric Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers
shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service
center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service
center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be
responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any
defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral
warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson
Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND
EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES.
Incidental damages include but are not limited to such damages as loss of time and loss of use. Consequential damages
include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work
properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
15
U.L. Model No.: CF620
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Part No. F40BP74450000
Printed in China 11/11
Form No. BP7445
U.L. Model No.: CF620