Samsung SDC-313B User guide

High Resolution Color Camera SDC-313B User Guide
Before installing and operating this product,
please read this manual thoroughly.
ENGLISH
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and proper input
power voltage. In order to that you can understand this manual thoroughly,
we'll introduce our model description.
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to
provide customers with more environment-friendly products.The Eco
mark represents Samsung Techwin's will to create environment-friendly
products, and indicates that the product satisfies the EU RoHS Directive.
nSDC-313B SERIES
• NTSC MODEL
• PAL MODEL
SDC-313BNA SDC-313BP
SDC-313BPD
SDC-313BPH
n MODEL DESCRIPTION
• SDC-313BXX
___
POWER SOURCE
SIGNAL SYSTEM
SHARP CCD
• SIGNAL SYSTEM
N --> NTSC MODEL
P --> PAL MODEL
• POWER SOURCE
--> AC 24V / DC 12V
D --> DC 12V
A --> AC 24V
H --> AC 230V
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
INFORMATION -This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
WARNING - C
hanges or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.WARNING - To prevent electric shock
and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person
and should conform to all local codes.
Contents
Features
6
• LENS (selection)
• SHUTTER (condition and speed control)
• WHITE BALANCE control
20
20
21
23
24
25
• BACKLIGHT (Backlight Compensation)
26
• AGC (Auto Gain Control)
27
• SSNR (Samsung Super Noise Reduction )
28
• SENS-UP (Low illuminance)
• SPECIAL
29
30
• EXIT
35
Camera Operation
■ Menu
■ Settings
Warning
7
Precautions
8
Component
10
Name and Function of Each Parts
■
■
■
■
FRONT
SIDE
BOTTOM
BACK
11
11
12
13
14
Installation
15
■ Lens
■ Connecting to Monitor
■ Connecting to Power
15
18
19
COLOR CCD CAMERA
4
User’s Manual
Troubleshooting
36
Specification
38
COLOR CCD CAMERA
5
User’s Manual
Features
Warning
The camera needs periodic inspection.
Horizontal Resolution 530 TV Lines
High Sensitivity
Clear image quality has been achieved by
employing a CCD with 410,000 pixels(NTSC),
470,000 pixels (PAL), which provides a
horizontal resolution of 530 TV lines.
The built-in high sensitivity COLOR CCD enables
a clear image even in 0.002 Lux(Sens-Up)
illumination.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time, a fire
may be caused.
Electronic DAY & NIGHT
This camera has a function that electronically
selects the mode that is appropriate for
daytime or night-time conditions.
The COLOR mode operates in daytime
conditions to provide optimum colors, and BW
mode operates in night-time conditions to
enhance the definition of the image.
SSNR
(Samsung Super Noise Reduction)
By using built-in SSNR function manufactured
by SAMSUNG TECHWIN, the amount of low
illuminance noise has been significantly
reduced, and the signal-to-noise ratio(S/N) as
well as horizontal resolution have been
improved, resulting in a clear and sharp image
display even in the dark.
Electronic IRIS
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not handle the camera with wet hands .
The electronic IRIS function enables continuous
automatic control of the shutter between
1/60(1/50) ~ 1/120,000 seconds.
Controlled by OSD Menu
PRIVACY Function
The camera can be controlled by selecting
text displayed on the monitor screen.
- ENGLISH, PORTUGUESE
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
The PRIVACY function conceals the areas you
do not wish to appear on the screen.
Additional Functions
VIDEO/DC Drive Lens
The video drive lens and the DC drive lens
can be selected by the touch of a switch.
COLOR CCD CAMERA
6
SENS-UP, MOTION DETECTION, MIRROR,
SHARPNESS and SYNC(INT/LL) functions are
also available.
User’s Manual
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
COLOR CCD CAMERA
7
User’s Manual
Precautions
Do not install under extreme
temperatures.
Do not install in high humidity
environments.
Use only under temperature conditions
between -10°C and +50°C. Provide good
ventilation when using in high temperature
conditions.
Do not install under unstable
lighting conditions.
May lower image quality.
Do not drop the camera or
subject it to physical shock.
May cause a product malfunction.
Never point the camera directly
at a strong light.
May damage the CCD.
Do not expose the camera to
rain or other types of liquids.
Do not expose the camera to
radioactivity.
Avoid touching the camera lens.
Wipe dry any liquids. Liquids may contain
minerals that are corrosive to electronic
components.
Radioactivity exposure may damage the
CCD.
Notes
Severe lighting changes or flickering may
hinder normal camera operation.
COLOR CCD CAMERA
8
The lens is the most important component
of the camera. Be careful not to smear it
with fingerprints.
User’s Manual
• Exposure to a spotlight or an object emitting strong light may cause smear or
blooming.
• Ensure that the power source complies with normal specifications before connecting
it to the camera.
COLOR CCD CAMERA
9
User’s Manual
Component
Names and Functions of Parts
FRONT
1. HIGH RESOLUTION COLOR CAMERA
A
2
3
4
2. Auto iris lens connection plug
3. C-Mount adaptor
A C
CD protection cap
Please cover the CCD SENSOR when not using it.
2 C
-Mount lens adaptor
Please install this adapter when using a C-Mount Lens.
3 C
S-Mount lens adaptor
Please remove the C-MOUNT lens adaptor and then attach it.
4 B
ack Focus clamp screw
Please loosen the clamp screw with a screwdriver before adjusting the Back Focal
length.
4. Instruction manual
COLOR CCD CAMERA
10 User’s Manual
COLOR CCD CAMERA
11 User’s Manual
Names and Functions of Parts
SIDE
BOTTOM
5
6
6 Tripod Mounting Plate screw hole
Please use the screw hole when fixing the
camera onto the Tripod Mounting Plate.
5 Auto iris lens connector
This is the connection terminal for the auto iris lens.
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
※The Tripod Mounting Plate can be separated and
attached to the top of the camera.
In this instance please do not tighten the screw to a depth
of more than 4mm, otherwise serious damage can occur
to the inside of the camera.
Notes
• This camera package does not include the Tripod Mounting Plate. Please refer to
the user's manual for installation of the Tripod Mounting Plate.
COLOR CCD CAMERA
12 User’s Manual
COLOR CCD CAMERA
13 User’s Manual
Names and Functions of Parts
Installation
Lens
BACK
7
Lenses are sold separately. Lenses such as an auto iris lens, CS-Mount lens and
C-Mount lens can be used.
8
Notes
⓫
9
❿
• Keep the lens surface clean, if it becomes contaminated with dirt or fingerprints
the picture quality suffers.
• Any foreign objects and fingermarks on the lens can cause inferior image quality
in low light level conditions.
When using an auto iris lens
*High Voltage Type(SDC-313BPH)
7 Auto iris lens selection switch : P lease change the mode to DC or
VIDEO depending on the type of auto
iris lens being used.
8 V
ideo output terminal : Sends video signal and connects to the video
input terminal of the monitor.
9 Power input terminal : C onnects to the power appropriate to each model.
❿ Setting button :
• SETUP button
: Used for the menu display. This button can be used to
confirm
settings after changing the value of the selected
function or current conditions.
• UP & DOWN buttons : Used for selecting items by moving the cursor up or
down on the menu screen.
• LEFT & RIGHT buttons: Used when changing item values, by moving the
cursor to the left or right on the menu screen.
1. Please peel off about 8mm of the outer skin of the auto iris lens cable.
approx. 8mm
2. P lease peel off about 2mm of the outer skin of the insulated conductor inside
the lens cable.
approx. 2mm
⓫ Power lamp: Lights up when the correct power is supplied to the camera.
COLOR CCD CAMERA
14 User’s Manual
COLOR CCD CAMERA
15 User’s Manual
Installation
3. Please remove the cover of the auto iris lens connection plug and solder the
lens cable to the connector pin in the plug.
Pin No.
No.1 Pin
No.2 Pin
No.3 Pin
No.4 Pin
LENS
VIDEO
Red (power)
NC
White (video signal)
Black (GND)
DC
DampingDamping+
Drive+
Drive-
When using a C-Mount lens
Please take off the CCD protection cap and
attach the C-Mount lens to the camera by
screwing it in clockwise.
C-mount adaptor
When using a CS-Mount lens
Lens cable
1. P lease take off the CCD protection cap and
C-mount adaptor.
C-mount adaptor
No.3 Pin
No.1 Pin
Connector
No.4 Pin
No.2 Pin
4. Please replace the auto iris lens connection plug cover and take off the CCD
protection cap, and then attach the auto iris
lens to the camera by screwing it in clockwise.
5. P lease insert the connection plug that is
connected to the auto iris lens cable into the
auto lens connector, which is located on the
side of the camera.
6. Please set the lens selection switch, located on
the side of the camera, to DC or VIDEO
depending on the type of auto iris lens which
is being used.
COLOR CCD CAMERA
16 User’s Manual
CCD protection cap
2. P lease attach the CS-Mount lens to the
camera by screwing it in clockwise.
C-mount adaptor
Notes
• P lease use the specified lens connection parts as shown in the picture below.
The use of the wrong sized parts of the wrong size may cause
damage to the inside of the camera or result in poor fitting.
• Use of a lens which is too heavy affects the balance of the
camera and may cause a malfunction. Please use a lens
that weighs less than 450g.
• Please select Av mode if possible when adjusting the
lens : 10 mm or less
automatic light control (ALC) of an auto lens. Use of PK mode C-mount
CS-mount lens : 5 mm or less
may cause hunting.
COLOR CCD CAMERA
17 User’s Manual
Installation
Connecting to Power
Since power specifications differ depending on the model, make sure you check your
model name and specifications before connecting power.
Connecting to Monitor
Please connect the video output terminal located on the back of the camera to the
monitor.
AC Power Type (AC 24V, 300mA)
The recommended adaptor specification for
SDC-313BNA is AC 24V / 300mA.
DC Power Type (DC 12V, 500mA)
The recommended adaptor specification
for SDC-313BPD is DC 12V / 500mA.
CCD Camera
Monitor
High Voltage Type (AC230V, 50Hz)
• The connection method varies depending on the type of monitor and accessories.
Please refer to the user's manual for each instrument.
• Please turn off the power when connecting.
• Please turn the 75Ω/Hi-Z switches of interim display devices to the Hi-Z position
and switch the end-of-line devices to the 75Ω position.
CCD Camera
Intermediate
End monitor
Use AC230V, 50Hz power source
for SDC-313BPH.
Dual Power Type (AC 24V / DC 12V)
The Recommended adaptor specification
for SDC-313BP is AC 24V/300mA or DC
12V/500mA.
When the resistance value of copper wire is at [20℃(68℉)]
Copper wire size(AWG)
Resistance value(Ω/m)
Voltage drop(V/m)
#24(0.22mm2)
0.078
0.028
#22(0.33mm2)
0.050
0.018
#20(0.52mm2)
0.030
0.011
#18(0.83mm2)
0.018
0.006
•A
s shown in the table above, voltage decreases as the wire gets longer.
Therefore use of an excessively long adaptor output line for connection to the
camera may affect the performance of the camera.
※ Note that adaptor is not supplied with accessory
※ Standard voltage for camera operation : DC 12V ±10%
※ There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
COLOR CCD CAMERA
18 User’s Manual
COLOR CCD CAMERA
19 User’s Manual
Camera Operation
Camera Operation
Menu
Settings
Settings can be made using the 5 buttons located on the back of the camera.
SETUP menu
LENS (selection)
• MANUAL
• DC •VIDEO
SHUTTER
(condition and speed control)
• ESC
• MANUAL
• FLK
WHITE BALANCE control
• ATW
• AWC
• MANUAL
BACKLIGHT
(Backlight compensation)
• OFF
• HIGH
• LOW
• MIDDLE
AGC (Auto Gain control)
• OFF
• HIGH
• LOW
• MIDDLE
SSNR
(Samsung super noise
reduction)
• OFF
• HIGH
• LOW
• MIDDLE
SENS-UP (Low illuminance)
• OFF
• AUTO
SPECIAL
• CAMERA ID
• MOTION DET
• SHARPNESS
• COLOR
• PRIVACY
• RESET
EXIT
• SYNC
• MIRROR
• RETURN
UP button
LEFT button
SETUP button
RIGHT button
DOWN button
1. P lease press the SETUP button
• Settings can now be made. The SETUP menu is displayed on the monitor.
SETUP
▶LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL 
EXIT
DC
--ATW
OFF
MIDDLE
LOW
OFF
2. P lease select any function you wish to activate by using the UP and DOWN
buttons.
• The arrow can be moved up or down by using the UP and DOWN buttons.
Please position the arrow to point to the function you wish to operate.
COLOR CCD CAMERA
20 User’s Manual
COLOR CCD CAMERA
21 User’s Manual
Camera Operation
SETUP
Select any function you
wish to operate by using
the UP and DOWN
buttons.
▶ LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
--ATW
OFF
MIDDLE
LOW
OFF
Modes can be changed
using the LEFT and
RIGHT buttons.
LENS (selection)
Using this function, you can control the screen brightness.
1. When the SETUP menu is displayed on the screen, please position the arrow
to point to 'LENS' by using the UP and DOWN buttons.
2. P lease select the type of the lens you wish to use by pressing the LEFT or
RIGHT button.
SETUP
▶LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
3. Please press the LEFT or RIGHT button if you wish to change mode.
• When the LEFT or RIGHT button is pressed, available values and modes are
displayed in order. Please keep pressing the button until you get to the mode
you wish to operate.
4. Please select 'EXIT' and then press the SETUP button to finish the setting.
DC
--ATW
OFF
LOW
AUTO
DC/VIDEO : Auto iris lens selection
Notes
• If
appears at the mode you wish to operate, it means that there is a submenu which can be selected by pressing the SETUP button.
• If --- appears at the mode item, it means that there is no mode available to be
selected.
Notes
• When using an auto iris lens, the setting of the auto iris lens selection switch,
located on the back of the camera, must be on DC or
VIDEO depending on the type of the lens which is being
used. (Please refer to the picture on page 15)
• The brightness of the screen can be adjusted in DC
mode. The brightness can be adjusted within the range
of 1~70. The optimum level of brightness for the user
can be achieved by adjustment.
MANUAL : Manual lens selection
3. Please press the SETUP button if you wish to return to the previous menu.
COLOR CCD CAMERA
22 User’s Manual
COLOR CCD CAMERA
23 User’s Manual
Camera Operation
SHUTTER (condition and speed control)
1. When the SETUP menu is on the screen, please position the arrow to point
to 'SHUTTER' by using the DOWN button.
2. Please select the shutter mode by pressing the LEFT or RIGHT button.
FLK : Please
select 'FLK' mode when flickering occurs on the screen, due to
an imbalance between illumination and frequency. NTSC
Model:1/100, PAL MODEL: 1/120
ESC :A
uto control of the shutter speed can be achieved. When ESC mode is
on, the speed is controlled automatically according to the brightness
of the screen.
MANUAL : T he shutter speed can be controlled manually.
SETUP
LENS
DC
SHUTTER
--▶WHITE BAL.
ATW
*Please select one of the 3 modes below.
SETUP
LENS
▶SHUTTER
WHITE BAL.
BACKLIGHT
AGC
WHITE BALANCE control
The screen color can be adjusted by using the WHITE BALANCE function.
1. P lease position the arrow to point to 'WHITE BAL' on the SETUP menu by
using the UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
MANUAL
ESC
ATW
OFF
MIDDLE
3. Please select 'MANUAL' mode if you wish to adjust the shutter manually.
• You can select speed from '1/60' to '1/120,000'sec (NTSC Models), '1/50'
to '1/120,000'sec (PAL Models).
4. Please press the SETUP button when all the settings are complete.
ATW(Auto Tracking White Balance) :
• NORMAL: This mode can be used within the color temperature range 1,800°K~
8,000°K. (fluorescent light, outdoor, normal environment)
• SPECIAL : This mode can be used within the color temperature range 1,800°K~
10,500°K (strong sodium vapor lamp or metal lamp)
AWC(Auto White Balance Control) : Please press the SETUP button while the camera is directed at a piece of white paper to obtain the optimum state under
current illumination. If the environment including the light source is changed, you have to adjust the white balance again.
MANUAL : The manual adjustment mode enables finer adjustment. Please select
ATW or AWC first. Please change to manual adjustment mode and press the SETUP
button. Please set the appropriate color temperature, and then increase or decrease the red and blue color values while monitoring the color changes on the object.
Notes
Notes
• When selecting DC/VIDEO lens, the shutter speed is fixed at 1/60 (1/50).
• While using the internal synchronous system, if the shutter setting is on 'ESC'
and the camera is directly facing a bright fluorescent light, the image on the
screen can be adversely affected. Therefore please choose the installation
location with care.
• When 'MANUAL' mode is on, the SENS-UP function does not operate.
COLOR CCD CAMERA
24 User’s Manual
• Under the following conditions the WHITE BALANCE function may not operate
properly. In such cases, please select the AWC mode.
A When the color temperature of the environment surrounding the subject is out of the
control range (e.g. clear sky or sunset).
2 When the object's surroundings are dark
3 If the camera directly faces a fluorescent light or is installed in a place where there
are considerable changes in illumination, the WHITE BALANCE function may become
unstable.
COLOR CCD CAMERA
25 User’s Manual
Camera Operation
BACKLIGHT (Backlight Compensation)
When there is a strong backlight behind the object, clear images of the background
as well as the object can still be obtained by using the BACKLIGHT function.
1. Please position the arrow to point to 'BACKLIGHT' on the SETUP menu by
using the UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
SETUP
LENS
SHUTTER
WHITE BAL.
▶BACKLIGHT
DC
--ATW
OFF
HIGH/MIDDLE/LOW : Y
ou
can adjust the sensitivity of Backlight Compensation.
it will be able to adjust the size and location of BLC window.
Regardless of location of the subject, BLC function is well
accomplished.
AGC (Auto Gain Control)
1. P lease position the arrow to point to 'AGC' on the SETUP menu by using the
UP and DOWN buttons.
2. P lease select the mode you wish to operate by pressing the LEFT or RIGHT
button. As the level of gain increases, the screen gets brighter and the level
of noise also increases.
HIGH
MIDDLE
LOW
OFF
: The gain increases or decreases within the range of 6dB ~ 26dB.
: The gain increases or decreases within the range of 6dB ~ 22dB.
: The gain increases or decreases within the range of 6dB ~ 10dB.
: The gain is fixed at 6dB.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
▶AGC
SSNR
SENS-UP
DC
--ATW
OFF
MIDDLE
LOW
OFF
3. P lease press the SETUP button. The BRIGHTNESS can be adjusted within the
range of 1~70.
OFF : BACKLIGHT function does not operate.
BACKLIGHT ON
COLOR CCD CAMERA
BACKLIGHT OFF
26 User’s Manual
4. Please press the SETUP button when all the settings are complete.
COLOR CCD CAMERA
27 User’s Manual
Camera Operation
SSNR (Samsung Super Noise Reduction)
The background noise in the low light level decreases automatically as the level
of gain changes.
1. Please position the arrow to point to 'SSNR' on the SETUP menu by using the
UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
▶SSNR
SENS-UP
SPECIAL
EXIT
DC
--ATW
OFF
MIDDLE
LOW
OFF
FF
O
: There is no reduction in noise level.
LOW
: T here is a small reduction in noise level with almost no ghost image.
MIDDLE : The most effective mode. There is a sufficient reduction in noise levels
without causing much ghost imaging.
HIGH : The level of noise is reduced greatly, however there is an increase in
ghost imaging.
Notes
•When AGC is turned off, SSNR does not operate.
COLOR CCD CAMERA
28 User’s Manual
SENS-UP (Low illuminance)
SENS-UP helps maintain a bright, clear screen image by automatically detecting
changes in the level of light in low light level conditions.
1. Please position the arrow to point to 'SENS-UP' on the SETUP menu by using
the UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
AUTO : Low light level auto mode
OFF : The function does not operate.
Notes
•When SHUTTER is in the manual mode, SENS-UP does not operate.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
▶SENS-UP
SPECIAL
DC
--ATW
OFF
MIDDLE
LOW
OFF
3. Please press the SETUP button when all the settings are complete.
Notes
•The maximum storage magnification in low light level can be adjusted by pressing
the SETUP button in 'AUTO' mode.(x2 ~ x128)
•As the magnification increases, the screen gets brighter; moving object gets more
afterimage.
• If storage magnification is increased while SENS-UP is operating, it may cause noise,
and spots may appear; however this is normal.
COLOR CCD CAMERA
29 User’s Manual
Camera Operation
SPECIAL
1. Please position the arrow to point to 'SPECIAL' on the SETUP menu by using
the UP and DOWN buttons.
2. P lease select the mode you wish to operate by pressing the UP or DOWN button.
SPECIAL
▶IMAGE ADJ COLOR
ON
SYNC
INT
MOTION DET
OFF
PRIVACY
OFF
LANGUAGE
ENGLISH
RESET
RETURN
IMAGE ADJ : 1) When the SPECIAL menu screen is displayed, select ‘IMAGE ADJ’ by Using the Up
and Down buttons so that the arrow indicates ‘IMAGE ADJ’
2) Select a desired mode using the Up and Down buttons.
IMAGE ADJ
▶MIRROR SHARPNESS
RETURN
OFF
ON
▒MIRROR
- ON : Sets a horizontal image inversion.
- OFF : Cancels the inversion.
MIRROR ON
MIRROR OFF
▒SHARPNESS : T he outline of the video image becomes cleaner and more
distinctive as the level of SHARPNESS increases. If the level goes
up excessively, however, it may affect the video image and
generate noise.
• Please press the SETUP button.
• The available range of level is 0 ~ 31.
AMERA ID : If the ID is input, the camera ID appears on the monitor.
C
1) Please
position the arrow to point to 'CAMERA ID' by using the UP or DOWN
button.
2) Please select 'ON' by pressing the LEFT or RIGHT button.
Notes
• If 'OFF' is selected, the ID does not appear on the monitor even if it has been input.
COLOR CCD CAMERA
30 User’s Manual
COLOR CCD CAMERA
31 User’s Manual
Camera Operation
5) When a name has been chosen, please select a position for the name display.
A Please move the cursor onto 'POS' and then press the SETUP button.
3) Please press the SETUP button.
Camera ID
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
←→ CLR POS END
4) Up to 15 letters can be used for the ID.
A Please move the cursor to the letter you wish to choose by using the UP and
DOWN button.
A The name will appear at the top left hand
corner.
Camera ID
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
←→ CLR POS END
Select
an ID from A, B~Y, Z, a, b~y, z, 0,1~8, 9 by using the UP, DOWN, LEFT and
RIGHT buttons.
3 Please lock in the letters by using the SETUP button.
• When the letter is locked in, the cursor moves to the next space.
4 Please repeat the above to input the ID.
2
Notes
Camera ID
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
←→ CLR POS END
FRONT DOOR
A Please find the position you wish to display
the name by using the 4 directional buttons,
and then press the SETUP button.
FRONT DOOR
6) Please select 'END' and then press the SETUP button to complete ID input.
• If the wrong name has been input.....
If you press the SETUP button after moving the cursor to CLR, all the letters will be
erased. If you want to correct a letter, please move the cursor to the arrow at the
bottom left of the screen and press 'SET'.Please position the cursor above the letter
you wish to correct, and then move the cursor onto the letter you wish to choose and
press the SETUP button.
COLOR CCD CAMERA
32 User’s Manual
➲ COLOR (Electronic DAY & NIGHT)
- AUTO : This camera has a function which electronically changes to the appropriate
mode for daytime or night-time. The COLOR mode is operated for daytime, and
it converts to BW mode for night-time.
- ON : The color mode is selected electronically.
COLOR CCD CAMERA
33 User’s Manual
Camera Operation
Notes
• If AGC is OFF, you can´t select AUTO mode.
• When an infrared light is used, there may be a problem with focusing and COLOR (DAY &
NIGHT).
SYNC : Two SYNCHRONIZATION modes are available INTERNAL and EXTERNAL
- OFF : MOTION DETECTION mode is cancelled.
- ON : Any motion in the selected areas is observed.
• Please select the area you wish to observe from the
4 areas in AREA SEL mode.
• Please select ON mode for the chosen area.
• Please adjust the size of the area to be observed by
using the UP, DOWN, LEFT or RIGHT button.
• P lease press the SETUP button to save the changes
and complete the setting.
LINE-LOCK. In LINE-LOCK mode, it synchronizes the video signal between
cameras without a synchronous generator. The line-lock synchronization is only
used in the areas of 60Hz(NTSC Model) / 50Hz(PAL Model)
- INT : Internal synchronization - LL : External line-lock synchronization
Notes
• There is no 'MD' output signal. 'MD' is on screen display only words.
• If you choose 'LL', you can adjust the desired phase.
Press the SET button.
• You can adjust the desired phase from 0 to 359.
Notes
• When the power frequency is 50Hz, you can not use line-lock mode (NTSC MODEL).
• When the power frequency is 60Hz, you can not use the line-lock mode (PAL MODEL).
• 'Sync' mode is fixed to 'INT' in DC12V input power.
MOTION DETECTION:
This product has a feature that allows you to observe movements of objects in 4
different areas on the screen, and the words 'MOTION DETECTED' appear on the
screen when movement is detected; hence a single individual can conduct
supervision efficiently. The camera detects an object's movement by sensing
disparity of outline, and level of brightness and color.
• Please press the SETUP button.
COLOR CCD CAMERA
34 User’s Manual
PRIVACY : T his modes conceals the areas you do not wish
to appear on the screen.
- OFF: Cancels the PRIVACY mode.
- ON : Operates the PRIVACY mode.
• Please press the SETUP button.
• Please select the area you do not wish to appear from the 4
areas in AREA SEL mode.
• Please select ON mode for the chosen area.
• Please adjust the size of the area to be concealed by
using the UP, DOWN, LEFT or RIGHT button.
RESET : Returns to the level which was set by the manufacturer for shipment.
RETURN : Returns to the SETUP menu.
EXIT
Saves all the setting menus and then exits.
COLOR CCD CAMERA
35 User’s Manual
Troubleshooting
If you have trouble operating your camera, refer to the following table. If the
guidelines do not enable you to solve the problem, contact an authorized
technician.
Problem
Nothing appears on
the screen.
Solution •Please check the power connection.
•Please check the video signal line connection.
Problem
Solution The MOTION DETECTION
function is not working.
•Please check if 'MOTION DETECTION' mode is turned
on.
•Please check if the MD LEVEL is too low.
•Please check and make sure that the auto lens switch
is set to DC (VIDEO) when using a DC (VIDEO) lens.
•Please check the Brightness of Auto Iris lens.
The video image is
not clear.
•Please check if the lens is clean.
Please clean the lens with a clean cloth or brush.
•Please adjust the contrast feature of the monitor.
•Please check the setting of the MD AREA. Colors are not quite right. •Please check the 'WHITE BAL' setting. (Please refer to
page 25)
The screen is flickering. •Please check if the camera is facing directly into
sunlight or fluorescent light.
•Please make sure that the screen is not exposed
directly to a bright light.
Please move the camera if necessary.
•Please check if an auto iris lens is being used. •Please check the connection of the lens connector
cable.
•Please readjust the back focus of the camera.
The screen is dark.
•Please adjust the contrast feature of the monitor. •If you have an intermediate device, set the 75Ω/ Hi-z
properly, and check the terminals. (refer to page 18)
•Please check if an auto iris lens is being used and
adjust the brightness level.
There is a problem with the
•Please check if an appropriate power source to the
camera operation. The
camera complies with the manufacturer's standard
camera surface is too hot and
requirement, or if the voltage keeps changing.
black stripes appear on the
screen.
COLOR CCD CAMERA
36 User’s Manual
L/L mode isn't able to be
selected. •Have you connected your camera to DC power source?
Connect it to AC power source.
COLOR (DAY & NIGHT) mode
is not working.
•Please check if the AGC menu is set to the OFF
position.
SENS-UP function is not
working.
•Please check if the AGC menu is set to the OFF
position.
•Please check if the SHUTTER menu is set to MANUAL
mode.
•Please check the limit of Sens-UP AUTO mode.
COLOR CCD CAMERA
37 User’s Manual
DECLARATION OF CONFORMITY
Specifications
ITEM
POWER
Total Pixels
C
C Effective Pixels
D
Sensor
Scanning System
S
y Synchronization
n
c Frequency
SDC-313BNA
SDC-313BPH
SDC-313BP
SDC-313BPD
AC 24V / 3.5W
AC 240V, 50Hz
AC 24V / DC 12V
DC 12V / 2.5W
811(H) x 507(V)
795(H) x 595(V)
768(H) x 494(V)
792(H) x 582(V)
1/3" IT CCD
2:1 Interlace
Internal / Line Lock 0~359° (Adjustable)
H : 15.734Khz
V : 59.94Hz
Backlight
E Compensation
L Gain Control
E
C White Balance
T
R Electronic
I
C Shutter Speed
A SENS-UP
L
O.S.D
KYUNGNAM, KOREA, 641-716
European Representative Name
Beginning Serial NO. S7020001
Year of Manufacture 2009. 01. 02
Conformance to EN 50081-1 : 1992
LOW / MIDDLE / HIGH / OFF Selectable
EMC-Directive 89/336 EEC and 92/31/EEC
LOW / MIDDLE / HIGH / OFF Selectable
EN 50130-4 : 1996
ON/AUTO(Electronically)
ATW (Normal Mode : 1,800°K ~ 8,000°K, Special Mode : 1,800°K ~ 10,500°K) / AWC / MANUAL
AUTO : (1/60(PAL:1/50) ~ 1/120,000sec) / Maual / Flickerless
AUTO / OFF (Selectable limit x2 ~ x128)
We, the undersigned, hereby declare that the equipment specified above conforms
Built-in (English, Portuguese)
Motion Detection
ON / OFF (4 Programmable Zone)
SSNR
to the above Directive(s).
LOW / MIDDLE / HIGH / OFF Selectable (Noise Reduction)
MIRROR
Manufacturer SAMSUNG TECHWIN CO., LTD ON / OFF
Privacy Function
ON / OFF (4 Programmable Zone)
Sharpness
ON / OFF (Level Adjustable)
IRIS Control
DC / VIDEO
Dimension
58(W) x 52(H) x 121(D)mm
Operating
Temperature / Humidity
Weight
42, SUNGJU-DONG CHANGWON-CITY,
CCTV Camera
0.3 Lux(F1.2), 0.002 Lux (SENS-UP x128)
COLOR
(DAY&NIGHT)
SAMSUNG TECHWIN CO., LTD
SDC-313BPD, SDC-313BPH, SDC-313BP
50dB (AGC OFF / Weight ON)
Min. Illumination
Manufacturer's Address
Model Name 1.0Vp-p / 75Ω (Video 0.7Vp-p, Sync 0.3Vp-p)
S/N (Y Signal)
SAMSUNG TECHWIN CO., LTD
Equipment Type/Environment More than 530 TV Lines
1.0Vp-p / 75Ω
89 / 336 / EEC
Manufacturer's Name European Representative Address
H : 15.625Khz
V : 50.00Hz
Resolution
Video Output
Internal Only
Application of Council Directive(s)
-10℃ ~ +50℃ / 30% ~ 80% RH
340g
COLOR CCD CAMERA
510g
38 User’s Manual
310g
310g
Legal Representative in Europe
Signature Signature
Full Name BONJENG GU
Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON, KOREA
Place
Date 2009. 01. 02
Date
COLOR CCD CAMERA
39 User’s Manual
SALES NETWORK
•
AMSUNG TECHWIN CO., LTD.
S
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703
TEL : +82-31-740-8151~8 FAX : +82-31-740-8145
•
AMSUNG TECHWIN AMERICA Inc.
S
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
•
AMSUNG TECHWIN EUROPE CO., LTD.
S
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungcctv.com
P/No. : Z6806-0791-01E
VAN 09. 10