Associated Electrics 6001 Assembly And Operating Instructions Manual

2

7/13

:: Introduction

Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10 Classic. Please take a moment to read through this manual to help familiarize yourself with these steps.

We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build.

:: KIT Features

Features in the RC10 Classic:

• Authentic replica of the RC10 Buggy Kit originally released in 1984

• Gold anodized 6061-T6 aluminum monocoque tub chassis

• Fully adjustable four wheel independent suspension

• Long travel, fluid filled gold anodized aluminum coil over shocks

• Low profile sealed six-gear transmission

• VariLok adjustable ball differential

• Exceptional ground clearance with low center of gravity

• Pro-Line front and rear tires with modular racing wheels

• Clear ProTech body with driver figure and wing

• Fiberglass shock towers

• Oilite bushings throughout

• Fits 6-cell NiMh and 2S LiPo battery packs

:: Additional

Your new RC10 Classic comes as a kit. There are some items you will need to complete your kit (refer to catalog for suggestions):

• R/C two channel surface frequency radio system

• Electronic Speed Control (ESC) • R/C Electric Motor

• Steering Servo and Servo Horn (AE # 9180, 89007)

• 2S, 7.4V Lipo stick battery or 7.2V NiMH battery

• Peak detection battery charger

• #2 Bit Type Phillips Screw Driver

• Polycarbonate specific paint

• Retaining Ring Pliers

• Thread Lock (AE # 1596)

• Pinion gear, size to be determined by type and wind of motor you use

Tools included:

• Allen wrenches (AE # 6950)

(.050”, 1/16”, 3/32”, 5/64”)

• Allen wrench .035”

• Molded tools (AE # 6956)

• Camber gauge (AE # 1719)

• Shock building tool (AE # 6429)

:: Other Helpful Items

• Silicone Shock Fluid (Refer to catalog for complete listings)

• Body Scissors (AE # 1737) • Reamer / Hole Punch

• FT Hex Wrenches (AE # 1655)

• Soldering Iron

• Tire Adhesive (AE # 1597)

• Wire Cutters

• Multi Tool (AE # 7494)

• Hobby Knife

• Needle Nose Pliers

• Calipers or a Precision Ruler • Green Slime shock lube (AE # 1105)

Associated Electrics, Inc.

26021 Commercentre Dr.

Lake Forest, CA 92630

Customer Service

Tel: 949.544.7500

Fax: 949.544.7501

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

:: Table of Contents

1................... Cover

2................... Introduction

3................... Table of Contents

4....................Nose Plate / Steering Build

A-AA)

4 - 5............. Front Suspension Build

B)

6 - 9.............Transmission Build

C-CC)

9 - 10...........Rear Bulkhead Build

D-DD)

10 - 11.........Rear Suspension Build

E-EE)

11 - 12........ Turnbuckles Build

F)

12 - 14........ Shocks Build

G-GG)

15 ................Chassis Build

H)

15 - 17........ Electronics Build

I)

17 - 19....... Wheels, Tires and Body Install

J)

20 - 21....... Tuning Tips

22 - 30....... Catalog

31................ Setup Sheet “Kit Setup”

32................ 1:1 Hardware “Fold Out”

33................ Setup Sheet “Blank”

34................ Back Cover

3

:: Notes

!

This symbols indicates a special note or instruction in the manual.

There is a 1:1 hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts.

Associated Electrics, Inc.

26021 Commercentre Dr.

Lake Forest, CA 92630

Customer Service

Tel: 949.544.7500

Fax: 949.544.7501

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

4

:: Nose Plate / Steering Build - Bag A-AA - Step 1

3323 x2

#8 aluminum washer (thick)

6310

RC10 front nose plate

6331

RC10 body mounts

(white)

6280

8-32 x 1/2 aluminum

FHPS

6281 x2

8-32 x 7/8 aluminum

FHPS

#1596 thread lock

6931

8-32 x 1/4

FHPS

6300

RC10 chassis

:: Nose Plate / Steering Build - Bag A-AA - Step 2

6271

Ballstud x4

.20 (silver)

!

6282

8-32 nut

(white) x2

Tighten 8-32 nuts until snug & bellcrank rotates freely!

3323 x2

#8 aluminum washer (thick)

6255

RC10 steering assembly

6255

RC10 steering assembly

:: Front Suspension Build - Bag B - Step 1

LEFT

6271

Ballstud

.20 (silver)

6299

E-clip

(small)

6216

RC10 steering blocks

(Left & Right)

Build left and right sides!

6213

RC10 front caster blocks,

15 degrees


6295

4-40 nut

6271

Ballstud

.20 (silver)



6219

RC10 front stub axles

!

Press stub axles into steering blocks.

Use a hard surface to push down on!


6299

E-clip

(small) x2

6227

RC10 front outer hinge pins

6223

RC10 king pins


6936

#4 aluminum washer x2

6927

4-40 x 3/4

SHCS x2

6295 x4

4-40 nut


6208 x6

RC10 front arm mounts


6230

RC10 front shock tower

6271

Ballstud x2

.20 (silver)

6925

4-40 x 1/2

SHCS x2

6280 x6

8-32 x 1/2 aluminum

FHPS


6205

RC10 front arms


6299

E-clip

(small) x2

5


6299

E-clip

(small) x2

6226

RC10 front inner hinge pins

6

:: Transmission Build - Bag C-CC - Step 1

6604

Drive gear pivot pin

6609

Drive gear pivot

!

Remove any burrs if necessary with hobby knife!

6611

RC10 spine plate

!

!

!

Key drive gear pin into slot on spine plate!

6609

Drive gear pivot nut



6610

RC10 idler gear pivot

6604

Bowed e-clip

NOTE: Install washer (1) before bowed e-clip (2)

2

6604

Washer

5mmx 0.17mm

1

!

Racer’s Tip:

Use a small amount of

CA glue on idle pivot hole.


6630

Oilite bushing

3/16x5/16x1/4

6612

RC10 axle drive gear

!

A little in-out play is normal on the outdrives

!

Snap internal retaining clip into groove with internal snap ring pliers!

Build 2

6604

RC10 internal retaining clip


6920

4-40 x 3/16

BHCS x2

!

Curved side of bowed E-Clip should point outwards!


7


6630


3/16x5/16x1/8

6613

RC10 idler gear

6299

E-clip

(small) x2

6613

0-80 x 3/16

BHCS x4

Build 2

!

Carefully tighten

screws in x- pattern!


6627

RC10 diff thrust washers

(small & large)

6618

RC10 diff shaft and pinion

6627

RC10 diff thrust bearing

!

Use just enough black grease to cover the balls on the thrust bearing!

6623

RC10 diff bushing x2

6605

RC10 bearing adapter

!

6617

RC10 diff pinion

6630


1/4 x 3/8 x 1/8

Slip the gear onto the tube and tap the assembly together using the handle of a hammer or a plastic handle of a screwdriver. Do not use a vise!

6617

RC10 diff tube w/hub

!

Press bushing in, make sure it is flush with diff hub!

Bushing


6634

Spur gear

81T, 48P

#6636 silicone lube

!

Apply silicone grease into each hole of the spur gear before inserting diff balls.

Insert diff balls opposite of stamped number on spur gear. Make sure they are evenly covered in lube!

6626 x8

1/8 diff balls

!

Caution:

Do not get any grease on the back side of the diff drive rings or the diff hub.

6625

Diff drive rings

!

Make sure diff rings sit flat on hub!

8


!

Caution:

Do not get any grease on the back side of the diff drive rings or the outer hub.

6624

RC10 diff outer hub

!

Make sure diff rings sit flat on hub!

6625

Diff drive rings

6628

RC10 diff spring

6629

5-40 locknut


6605

RC10 transmission case

(right)

6607

RC10 motor plate

1

6605

RC10 transmission case

(left)

6605

RC10 bearing adapter

!

Lock nut should be flush with shaft to start!

6630


3/16 x 5/16 x 1/8

!

Cutting a slot in the bearing adapter will make e-clip installation easier!

2


!

Racer’s Tip:

Use a dab of CA glue on the felt seals.

6299

E-clip

(small)

6633

RC10 felt seal x2

6633

RC10 felt x2

!

Press nut all the way inside the transmission case.

7260

4-40 plain nut

(small)

9

:: Transmission Build - Bag C-CC - Step 10 :: Rear Bulkhead Build - Bag D-DD - Step 1

6295 x2

4-40 nuts


6927

4-40 x 3/4

SHCS x2

6928

4-40 x 1

SHCS x3 6926

4-40 x 5/8

SHCS

6378

RC10 rear shock tower

:: Rear Bulkhead Build - Bag D-DD - Step 2

6924

4-40 x 3/8

SHCS x2

6932

4-40 x 5/16

SHCS x2

6323

RC10 rear bulkhead


6271

Ballstud x2

.20 (silver)

6280

8-32 x 1/2

FHPS x2

6926

4-40 x 5/8

SHCS x2

6280

8-32 x 1/2

FHPS x4

10


6331

RC10 body mounts

(white)

6925

4-40 x 1/2

SHCS x4

6936


6327

RC10 wing tubes x2

!

Press wing tubes into bulkhead!

6326

RC10 transmission brace

6280

8-32 x 1/2

FHPS


:: Rear Suspension Build - Bag E-EE - Step 1

6360

RC10 rear arm mounts

6380

RC10 rear inner hinge pins

6285

4-40 x 1/4

SHCS x2

!

Racer’s Tip:

Use a small amount of CA glue on wing tube ends before inserting into bulkhead.

!

Forward holes

6355

RC10 rear arms


6299

E-clip

(small) x2


6374

1/4 rear stub axle

6365

RC10 rear hub carrier


6373

1/4 axle shims x3


6630 x3


1/4 x 3/8 x 1/8

!

6375

Roll pins

.1 dia x 3/8

6280 x2

8-32 x 1/2

FHPS


6271

Ballstud x2

.20 (silver)



6381

RC10 rear outer hinge pins

6299

E-clip

(small) x2

2

6372

Dogbone spacer

6370

Dogbone

1

6372

Dogbone spring

!


:: Turnbuckles Build - Bag F - Step 1

!

Use a pair of pliers or wire cutters to carefully hold the turnbuckle while threading on ball cups.


6256

RC10 tie rod set

(1.25”)

Rear Camber Turnbuckle

0.56” (14.20mm)

6279

Ball cups

(white) x2


!


6256


(1”)

6279

Ball cups

(white) x2

Steering Rack Turnbuckle

0.49” (12.44mm)

11

12


!


6256


(1.25”)

Front Camber Turnbuckle

0.53” (13.5mm)

6279

Ball cups

(white) x2



!


6256


(1.65”)

Steering Turnbuckle

1.09” (27.70mm)

6279

Ball cups

(white) x2


:: Shocks Build - Bag G-GG - Step 1

Remove spurs

Piston

6299

E-clip

(small)

6461

Shock shaft, front (0.56)

Piston number here

Use #2 = front shocks

Use #2 = rear shocks

6458

Shock shaft, rear (1.32)

!

TIP: Use marker to mark the piston numbers for easy identification!

6465

Shock pistons

(1, 2, 3)

6299

E-clip

(small)

Build two front and two rear shock shafts!


5407 x2

Red o-ring

6440 x2

Off-road shock rebuild kit

6449

Shock body, front (0.56)

Remove spurs

Shock fluid

30wt #5422

6429

Shock assembly tool

Front

Shock

SNAP!

6446

Shock body, rear (1.32)

Shock fluid

30wt #5422

13

Rear

Shock

!

Place on table and push down hard until clamp snaps into place

SNAP!


Front

Shock

Rear

Shock

6469

Shock cap o-ring

6466

Shock x2 downstops

6468

Shock pivot ball

6468

Shock rod end

Build x2 front and x2 rear shocks


Step 1-3

Shock fluid

30wt

#5422

Step 3-4

Shock fluid

30wt #5422

Step 5-6

6450

RC10 shock cap

Step 7

* Shock Bleeding Steps:

1. Pull shock shaft down.

2. Fill shock body 3/4 full with silicone fluid.

3. Slowly move the shock shaft up and

down to remove air from under piston.

4. Wait for bubbles to come to surface.

5. Fill shock body to top with silicone fluid.

6. Place several drops of oil in the cap and

on cap threads.

7. Install cap and tighten completely.

8. Slowly compress shaft all the way to

the top. If there is pressure at the top

of the stroke, there is too much oil.

You must bleed it out.

9. Slowly pull shaft down.

10. Unscrew the cap 3/4 turn and tilt the

shock at a slight angle.

11. Slowly compress the shaft to push out

excess oil and air. You should see

bubbles coming out from under the cap.

12. With the shaft compressed, tighten the

cap and re-check for pressure at the top

of the stroke. If there is still pressure,

repeat steps 9 thru11.

14


Front:

6.5mm

Rear:

0mm

6451

RC10 shock collar

6924

4-40 x 3/8

SHCS


6936

#4 aluminum washer

6451

RC10 shock bushing

6496

Front shock spring, silver

(3.85lb)

6478

Rear shock spring, silver

(2.10lb)

6451

RC10 spring cup

Build x2 front and x2 rear shocks

4436

4-40 x 5/16 set screw

6242

4-40 locknut


6451

RC10 shock bushing


6224

Lower shock pin

!

Make sure the set screw engages the groove on the shock pin!

6936


6242

4-40 locknut

6927

4-40 x 3/4

SHCS


:: Chassis Build - Bag H - Step 1

2

6917

4-40 x 3/8

BHCS

1

6288

4-40 x 1/4

BHCS


:: Electronics Build - Bag I - Step 1

6936


6916 x2

4-40 x 1/2

SHCS w/hole

6333

RC10 battery cup and strap

6320

RC10 nose brace tubes

6255

Z bend x2 servo wire

6337

RC10 antenna mount

6951 x2

4-40 x 1/8 set screw


6338

Antenna tube and cap

6292

4-40 x 3/8

FHCS

6255

1/8 set collar x2

!

Wires may need to be bent slightly to clear some servos, depending on configuration!

15


!

Align Z-bend wires so that the set screw tightens down on both wires at once!

6337

RC10 servo mounts x2

Servo not included!

6924

4-40 x 3/8

SHCS x4

Servo horn and screw not included!

6936


89007

Servo horn

(recommended)

16


Follow steps below to properly install Z bend wire into servo horn and steering link.

!

NOTE: Hole choice may vary depending on servo and servo horn used.

1) Press down on the

Z bend wire....

2) Rotate the wire so the Z bend wire is fully installed into steering link as shown.

TIP: Chamfering the top of the hole slightly will help to press in Z bend wire.


Receiver not included!

!

Install Z bend servo wire into steering bellcrank as shown. Ensure that full steering throw can be achieved with your servo horn setup!

!

Space collars as wide as possible while still clamping both wires.


6922

4-40 x 1/2

FHCS x2

6936


ESC not included!

6727 x2

Servo tape

Motor not included!

Pinion not included!

!

See page 20 to set gear mesh properly!

31531

3 x 6mm

BHCS x2

6920

4-40 x 3/16

BHCS x2

6608

Gear cover and plug

17


Battery not included!

6332

Body clip

:: Wheels / Tires and Body - Bag J - Step 1

TIP: For faster motors, it is recommended to glue the tire bead to the wheels!

6850

RC10 front wheel

!

Use optional wheel insert for aftermarket vintage tires!

6865

RC10 edge front tire

Build 2

6850

RC10 front wheel

!

Do not overtighten wheel screws!

6932

4-40 x 5/16

SHCS x3


!

6192 x2

RC10 wheel knock off

(for display only)

!

6800

RC10 rear wheel

!

Do not overtighten wheel screws!

6932

4-40 x 5/16

SHCS x3

6815

RC10 champion rear tire

6800

RC10 rear wheel

Build 2

!

6192 x2

RC10 wheel knock off

(for display only)

6630 x2


3/16x5/16x1/8


6242

4-40 locknut x2

6952

8-32 steel locknut x2


18


Painting Tips:

Body and Wing:

Your RC10 Classic comes with a clear polycarbonate body and wing. You will need to prep the body and wing before you can paint them. Wash the inside thoroughly with warm water and liquid detergent. Dry the body and wing using a clean, soft, lint-free cloth. Use high quality masking tape to make masks for the windows and install them on the inside of the body. (RC cars get painted from the inside). Using high quality masking tape, apply tape to the inside of the body to create a design. Spray (either rattle can or airbrush R/C specific paint) the paint to the inside of the body (prefferably dark colors first, lighter colors last).

6160

Protech

Buggy body, unpainted

NOTE: use ONLY paint that is recommended for use with

(polycarbonate) plastics. If you do not, you can destroy the plastic body and wing!!!!).

After painting, cut the body and wing along the trim lines.

Make sure to drill or use a body reamer to make the holes for the body mounts, wing mounts, and antenna!


Light Buckets:

Press the light bucket halves together. You can use CA glue if you would like.

You can paint or dye the light buckets to any desired color.

Install light buckets with #9898 SHCS in areas shown.

6192

Light buckets

9898

2-56 x 3/16

SHCS x4

!

Mount the light buckets in any location of your choosing, or not at all.


Painting Tips:

Driver :

Your RC10 Classic comes with a clear polycarbonate driver figure. You will need to prep the driver figure before you can paint it. Wash the inside and outside thoroughly with warm water and liquid detergent. Dry the driver figure using a clean, soft, lint-free cloth. The driver figure can be painted from the inside or the outside, depending on what type of finish you would like. If painted from the inside, the painted sections will appear glossy. If painted on the outside, the painted sections will appear flat or matte finished. Trim as shown and install inside the body using strapping tape. After painting, cut the body and wing along the trim lines.

6180

RC10 driver figure, clear

NOTE: use ONLY paint that is recommended for use with (polycarbonate) plastics. If you don’t, you can destroy the plastic body, driver figure, and wing!!!!.


6332

Body clip


6187

Wing, clear

6192

Wing x2 mounts

6332

Body clip

19

6191

Wing mount wire


!

TIP: Bending the wire as shown can help ensure the wing buttons are parallel.

!

TIP: Bend wire to create tight fit inside wing tubes.

20

:: Tuning Tips

Tips for Beginners:

Before making any changes to the standard setup, make sure you can get around the track without crashing.

Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps. Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make adddtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and try another change. When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away.

Use this as a guide for future track days or conditions.

Peridicaly check all moving suspension parts. Suspension components must be kept clean and move freely without binding to prevent poor and/or inconsistent handling.

Motor Gearing:

Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used motor types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your motor and electronic speed control manufacturers for more information. Team Associated is not responsible for motor damage due to improper gearing. * These gearings are for use with advanced timing speed control settings!

RC10 Classic Gear Ratio Chart (Internal Gear Ratio 1.83:1)

Motor Pinion Spur FDR

27T Stock Brushed

19T Super Stock Brushed

17.5 Reedy Sonic Brushless *

17.5 Reedy Sonic Brushless

13.5 Reedy Sonic Brushless *





18

18

19

27

18

26

19

18

18

81

81

81

81

81

81

81

81

81

8.23:1

8.23:1

7.80:1

5.49:1

8.23:1

5.70:1

7.80:1

8.23:1

8.23:1

Due to the original design of the RC10, motors exceeding the power of a 8.5T motor are NOT recommended, to prevent damage to the drivetrain!

Set The Gear Mesh:

You should be able to rock the spur gear back and forth in the teeth of the pinion gear without making the pinion gear move. If the spur gear mesh is tight, then loosen the #31531 screws and move the motor away, then try again.

A gear mesh that is too tight or too loose will reduce power and damage the gear teeth.

VariLok Diff Adjustment Tips:

Be sure to only use Associated diff lube #6636, and apply a small amount on both sides of the diff balls. Do not use this diff grease anywhere else on the vehicle! It is not intended as a lubricant (Use only

Associated diff lube as it has special additives to ensure the balls roll instead of slide).

The RC10 Classic is not equipped with a slipper clutch like most current

R/C vehicles are. Therefore, particular care and attention is necessary when setting the VariLok differential. Set the differential by starting with the 5-40 nut flush with the end of the diff shaft. Next, turn on the car and hold the tires (as seen below) with transmitter in hand. Quickly give the car a 75-100% burst of throttle. Note, if the spur gear spins and the car does not move forward then the diff is too loose. Adjust the diff nut in 1/8 turn increments until the spur gear doesn’t slip. At this point, the diff is set as free as possible without slipping. Tightening the diff nut even further will increase the amount of power that is transferred to the tire that has the most load and will not ‘diff out’ as easily. Locking down the diff nut is not recommended because the only slipping that can occur will be between the drive rings and hubs. This can create a tremendous amount of heat.

Wheelbase Adjustment:

The wheel base on the RC10 Classic can be adjusted by moving the rear arm mounts forward or backwards. The kit setting has the arm mount back which provides the most stability over bumps and rhythm sections.

Going to the shorter wheelbase option will improve rear traction.

21

:: Tuning Tips (cont.)

Front Camber Links:

Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the tower. Shortening the camber link (or lowering the ball end) will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ball end) will give the front more roll and slower steering response. Longer camber links are typically used on high grip tracks and shorter links tend to work better on medium-grip loose tracks.

Front Camber:

Camber describes the angle at which the tire and wheel rides when looked at from the front. Negative camber means that the tire leans inward at the top. A good starting camber setting is -1°. Use the included #1719 camber gauge to set your camber. Positive camber, where the top of the tire is leaning out, is not recommended.

Caster:

!

*Raise or lower the ball end on the front shock tower

!

*Checking camber with camber gauge

Caster describes the angle of the kingpin as it leans toward the rear of the vehicle. Positive caster means the kingpin leans rearward at the top. The supplied 15° caster blocks (#6213) are recommended in most cases. For less corner entry steering and more exit steering, try the optional 30° caster blocks (#6210). Optional 30° caster blocks may require trimming of the stock front arms for clearance.

Rear Camber Link:

Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the rear chassis brace. Shortening the camber link (or lowering the ball end) will give the rear end less roll and the car will tend to accelerate or “square up” better. Lengthening the camber link (or raising the ball end) will give the rear more roll and more cornering grip. Longer camber links are typically used on high grip tracks, while shorter links tend to work better on medium grip loose tracks. The far inside hole was a tuning option introduced later on. It requires a 1.65” turnbuckle (#6262, 1403, or 6256)

!

*Raise or lower the ball end by adjusting the ballstud location on the bulkhead

Rear Camber:

Camber describes the angle at which the tire and wheel rides when looked at from the back. Negative camber means that the tire leans inward at the top. A good starting camber setting is -1°. Use the included #1719 camber gauge to set your camber. Adding a small amount of positive camber, where the top of the tire is leaning out, will tend to improve straight-line acceleration on loose tracks.

Ride Height:

Ride height is the distance from the ground to the bottom of the chassis. The standard front ride height setting is with the front arms just below level or 24mm (Ride Height Gauge #1449). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, measure ride height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary so that the left & right arms appear to be level.

!

*Front arms should be just below level ride height

The rear ride height setting you should use most often is with the outdrive, driveshaft, and axles all on the same imaginary horizontal line (reffered to as “bones level”) or 24mm (Ride Height Gauge

#1449). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, measure ride height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary so that the left & right driveshafts appear to be level.

Motor Maintenance:

!

!

*Dog bones should be in a straight line when ride height is set at “Bones level”

*TIP: Set the rear dog bones level and then adjusting the front to make the chassis parallel to the ground.

Brushed motors require frequent maintenance to keep performance levels at their maximum. Between runs and after letting the motor cool completely, inspect the brushes to ensure that they are moving freely in their holders. Remove the springs and slide the brushes in and out of their holders checking for any resistance or rough spots. If found, remove the brush and carefully wipe it clean. Removing buildup will allow the brush to slide freely and create maximum contact with the commutator resulting in maximum power output. After every 3-5 runs, remove the brushes from their holders and inspect the tips for wear or burning. If there is noticeable wear (less than 75% of the brush remaining), it is best to cut the commutator and replace the brushes with a new pair. If the tips become a burned blue color, the lubricant in the brush has been burned away and new brushes should be installed. Occasionally, the motor should be cleaned with a soft brush to prevent dirt build up around the brush hood area and ball bearings.

At this time, it is a good idea to add one drop of bushing / bearing oil to each bushing or ball bearing.

If using a brushless motor, please refer to the motor manufacturer’s guidelines for proper maintenance.

22

:: Shocks

5407

6299

6429

6440

6446

6449

6450

6451

6458

6461

6465

6468

6469

6924

Red O-Rings

1/8” E-Clips

Shock Assembly Tool

Off Road Shock Rebuild Kit

Shock Body, Rear (1.32)

Shock Body, Front (0.56)

RC10 Shock Cap

RC10 Shock Accessories

(spring retainer, clamp, bushing)

Shock Shaft, 1.32” stroke

Shock Shaft, .56” stroke

Shock Piston, (1, 2, 3)

RC10 Shock Rod Ends / Pivots

Black O-Ring

4-40 X 3/8” SHCS

1

1

1

1

8

12

1

1

1

1

4ea.

2

4

6

6450

6469

6449 (F)

6446 (R)

6299

6465

6299

6440

6440

5407

6440

5407

6440

6440

6461 (F)

6458 (R)

6451

6451

6924

6468

6468

6493

6494

6496

6497

8232

6478

6480

6481

6482

7434

7435

7436

:: Springs

1581

1582

Factory Team Buggy Front Spring Kit. I pr of green, silver, blue, black springs

Factory Team Truck/Buggy Rear Spring Kit.

I pr of green, silver, blue, gold, red springs

Front Buggy Spring Brown 2.80 lb

Front Buggy Spring Green 3.50 lb

Front Buggy Spring Silver 3.85 lb (Kit)

Front Buggy Spring Blue 4.20 lb

Front Buggy Spring Black 3.20 lb

1

1

Pr.

Pr.

Pr.

Pr.

Pr.

Rear Spring Silver 2.10 lb (Kit)

Rear Spring Green 1.90 lb

Rear Spring Black 1.74 lb

Rear Spring Gray 2.33 lb

Rear Spring Blue 2.55 lb

Rear Spring Gold 2.75 lb

Rear Spring Red 2.95 lb

Pr.

Pr.

Pr.

Pr.

Pr.

Pr.

Pr.

:: Slipper / Gear Cover

6605

6608

6617

6618

6623

6624

6625

6626

6627

6628

6629

6630

6634

6920

31531

RC10 Bearing Adapter

Gear Dust Cover w/Plug

RC10 Diff Tube w/Hub

RC10 Diff Shaft & Pinion

RC10 Diff Teflon Bushing

RC10 Diff Outer Hub

Diff Drive Rings

1/8” Diff Balls

RC10Diff Thrust Bearing

RC10 Diff Spring & Nut

5-40 Diff Locknut

RC10 Oilite Bushing Set

RC10 81T Spur Gear, 48P

4-40 x 3/16” BHCS

M3 x 6 BHCS

16

1ea.

1

6

1

1

6

6

1

1

2

2

1

1

2

:: Shock Fluid

5420 10 Weight Silicone Shock Fluid

5431

5432

5433

5434

5435

5436

5437

5438

5421

5422

5423

5424

5425

5426

5427

5428

5429

5430

20 Weight Silicone Shock Fluid



22.5 Weight Silicone Shock Fluid















6625

6634

6626

6625

6628

6624

6629

6608

31531

6618

6627

6623

6617

6605

6630

6617

6623

6608

6920

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

2oz.

:: Turnbuckles / Servo

6255

6256

6279

6337

6922

6924

6936

6951

89007

RC10 Steering Assembly

RC10 Tie Rod Set

(2x 1”, 4x 1.25”, 2x 1.65”)

White Ball Cups

RC10 Servo/Antenna Mount

4-40 x 1/2” FHCS

4-40 x 3/8” SHCS

#4 Washer, Aluminum

4-40 x 1/8” Set Screw

Steering Servo Horn

1

1

14

1

6

6

10

6

1

6279 6256 6279

6337

6922

6337

6936

6924

6951

6924

6951

6922

6255

6255

89007

6255

6255

23

:: Steering

3323

6255

6271

6281

6282

#8 Aluminum Flat Washer, thick

RC10 Steering Assembly

Short Ballstud, stainless steel, short

8-32 x 7/8” Aluminum FHPS

8-32 Locknut, Nylon (White)

12

1

12

6

6

6271

6271

6282

6255

3323

6281

6282

6271

6255

6271

6255

3323

6281

:: Antenna Mount / Battery Strap

6292

6332

6333

6337

6338

6916

6936

4-40 x 3/8” FHCS

Body Clip

RC10 Battery Cup

RC10 Servo/Antenna Mounts

Antenna Tube with Cap, black

4-40 x 1/2” SHCS w/hole


1

1

1

6

6

6

10

6338

6338

6916

6936

6333

6916

6332

6333

6337

6292

6292

6292

24

:: Front Arm

6226

6227

6242

6271

6280

6295

6299

6630

4187

4436

6192

6205

6208

6213

6216

6219

6223

6224

Nylon Spacer, 1/32” (.030)

4-40 x 5/16”, Set Screw

RC10 Accessories

RC10 Front Arms

RC10 Front Arm Mounts

RC10 Front Caster Blocks, 15 deg

RC10 Steering Blocks

RC10 Front Stub Axles

RC10 King Pin w/Clips

Lower Shock Pin

RC10 Front Inner Hinge Pin

Hinge Pin, outer, 1.020”, w/ clips

4-40 Steel Locknut

Short Ballstud, stainless steel, .20


4-40 Nuts

E-Clip, 1/8”


12

4

1

1ea.

1ea.

2

1

6

12

16

1ea.

2

2

2

2

18

12

1

6280

6299

4187

6223

6213

4187

6299

6208

6299

6271

6271

6216

6295

6219

6299

6226

4436

6299

6224

6227

6299

6205

6630

6299

6192

6242

:: Rear Arm

6372

6373

6374

6375

6380

6381

6630

6927

6952

6192

6271

6280

6299

6355

6360

6365

6370

RC10 Accessories

Short Ballstud, tainless steel, .20


E-Clip, 1/8”

RC10 Rear Arms

RC10 Rear Arm Mounts

RC10 Rear Hub Carriers

RC10 Dogbone

1/16” Plastic Spacer, with spring

1/4” Rear Axle Shims/Spacers

Rear Stub Axle, with roll pin

Roll Pin for Stub Axle

RC10 Rear Inner Hinge Pins

Hinge Pin, Rear, Outer


4-40 x 3/4” SHCS

8-32 Locknut, Steel

2

1

6

6

2

14

1

6

2

1

12

16

12

1ea.

1ea.

2

1

6372

6370

6374

6360

6299

6280

6280

6380

6927

6299

6630

6372

6373

6299

6355

6365

6271

6299

6630

6192

6373

6375

6952

6381

25

:: Front Shock Tower

6230

6242

6271

6295

6451

6925

6927

6936

RC10 Front Shock Tower

4-40 Locknuts, Steel

Short Ballstud, Stainless Steel, .20

4-40 Nuts


4-40 x 1/2” SHCS

4-40 x 3/4” SHCS


1

6

12

6ea.

1

6

6

10

6242

6936

6451

6295

6936

6242

6927

6936

6451

6936

6927

6295

6271

6295

6925

6230

6295

6271

6925

:: Rear Shock Tower

6242

6295

6378

6451

6924

6927

6932

6936

4-40 Locknuts, Steel

4-40 Nuts

RC10 Rear Shock Tower


4-40 x 3/8” SHCS

4-40 x 3/4” SHCS

4-40 x 5/16” SHCS


6

6ea.

1

1

6

6

6

10

6451

6242

6936

6295

6927

6378

6927

:: Wheels / Tires

6800

6815

6850

6865

6932

RC10 Rear Wheels

RC10 Champion Rear Tires

RC10 Front Wheels

RC10 Edge Front Tires

4-40 x 5/16” SHCS

2

2

2

2

6

6932

6924

6932

6242

6936

6451

6295

6800

6800

6800

6815

6800

6850

6850

6865

6850

6932

6932

26

:: Rear Bulkhead

6271 Short Ballstud, Stainless Steel, .20

6280

6323

6326

6327

6331

6332

6925

6936


RC10 Rear Bulkhead

RC10 Transmission Brace

RC10 Wing Tubes

RC10 Body Mounts (White)

Body Clips

4-40 x 1/2” SHCS


12

16

1

1

2

2

6

6

10

6327

6331

6271

6327

6323

6332

6925

6925

6936

6936

6936

6936

6925

6925

6271

6326

6280

:: Transmission

6612

6613

6630

6633

6920

6926

6928

7260

6280

6285

6299

6604

6605

6607

6609

6610

6611


4-40 x 1/4 SHCS

E-Clip, 1/8”

RC10 Transmission Fasteners Kit

RC10 Transmission Case

RC10 Motor Plate

RC10 Drive Gear Pivot

RC10 Idler Gear Pivot

RC10 Spine Plate

RC10 Axle Drive Gear

RC10 Idler Gears w/Screws


RC10 Felt Seal Set

4-40 X 3/16” BHCS

4-40 X 5/8” SHCS

4-40 x 1” SHCS

4-40 Small Pattern Plain Nut

1

2

1

2

6

6

6

12

1

1

1

1

1

16

12

12

1

7260

6633

6633

6607

6920

6612

6299 6613

6630

6604

6609

6630

6613

6604

6611

6280

6609

6604

6630

6610

6613

6630

6613

6299

6612

6920

6285

6605

6605

6605

6630

6928

6280

6928

6299

6928

6926

6633

6633

27

:: Chassis

3323

6280

6288

6300

6310

6320

6331

6332

6917

6926

6931

#8 Aluminum Thick Washer


4-40 X 1/4” BHCS

RC10 Chassis

RC10 Front Nose Plate

RC10 Nose Brace Tubes

RC10 Body Mounts (White)

Body Clips

4-40 X 3/8” BHCS

4-40 X 5/8” SHCS


12

12

6

1

1

2

2

6

6

6

6

6926

6331

6288

6917

6917

6280

6332

3323

6320

6931

6320

6310

6288

6300

:: Lubes & Adhesives / Misc.

1105

1596

1597

6588

6636

6727

FT Green Slime Shock Lube

FT Locking Adhesive

FT Tire Adhesive, medium

Black Grease - 4cc

Silicone Grease - 4cc

Servo Tape

1

1

2

1

1

1

:: Body, Wing, and Decals

3834

6121

6160

6180

6181

6182

6183

6186

6187

6188

6190

6191

6192

6193

6193B

6866

9788

AE Blue Embossed Logo Sticker

Viper Buggy Body, clear

Protech Buggy Body, clear - Kit

RC10 Driver Figure, clear

High Downforce Wing Kit, w/wire and buttons

High Downforce Wing, 5 1/2”

High Downforce Wing, 7”

Large Wing

RC10 Wing Kit

Sprint Wing w/Side Dam

Wing Mounts, Adjustable (wing-things)

Wing Mount Kit

RC10 Accessories (Wheel Knock Offs, Headlights)

Wing Mounts, Aluminum

FT Wing Mounts, Aluminum (blue)

RC10 Classic Decal Sheet

Chassis Protective Tape

1

1

1

1

2

1

1

1

1

1

1

2

1

1

1

1

2

:: XP Electronics

29107

29125

29133

29134

29138

29139

29140

29141

29142

29143

29144

29166

29167

29168

29209

29210

29211

29212

29214

29215

29216

29250

29251

29252

29253

XP DS1903/S1903 Metal Gear Set

S1903MG Servo

XP DS1903 Digital Servo

XP DS1903MG Digital Servo

XP SC500-BL Brushless ESC


XP SC200 Brushed ESC


XP ESC Fan Option






Gear Set, DS1313

Gear Set, DS1015

Servo Case , DS1313/DS1015

Accessory Pack, DS1313/DS1015

TRS403-SSi 2.4GHz 4Ch Receiver

XP2G 2.4GHz Radio System

XP3G 2.4GHz Radio System



XP DS1505 Metal Gear Set

XP DS1510 Metal Gear Set

6926

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

28

:: Factory Team and Option Parts

6463

6465

6473

6619

6902

6909

6910

6937

6943

8253

6325

6366

6390

6416

6419

6431

6434

6435

6438

6443

6260

6261

6262

6263

6264

6270

6271

6272

6273

6274

897

1409

1736

1779

4449

6210

6220

6221

6222

6241

6242

6259

8265

8266

8267

8268

8269

8270

8271

8272

8254

8255

8256

8257

8258

8259

8260

8261

8263

8264

Bearing, 1/4 X 3/8, flanged

FT Titanium Turnbuckles, 1.00”, blue

FT Body Clips, Metallic Blue, Short

FT Servo Mount, Blue Aluminum

4-40 Aluminum Locknut, small pattern

Front Block Carrier, 30° Caster

Aluminum Front Inline Axle

Inline Steering Block

4-40/5-40 Nylon Locknut, black

RC10 Front End Screw Set

4-40 Steel Locknut

Turnbuckle Tie Rod Set, black

Turnbuckle, 1.00”, black





Short Ballstud, .20, Stainless Steel, short

Short Ballstud Set, Stainless Steel, short

Ballstud Dust Cover, foam

Long Ballstud, .30, silver

Ball Cup, molded

Transmission Brace, black

Rear Hub Carrier, 1.5° toe-in (per side), black

Rear Wheel Knockoffs, (2 prong) white

FT Gold Shock Shaft, 1.32” stroke

FT Gold Shock Shaft, .56”

Shock Kit, hard anodized, 1.32”

Shock Kit, hard anodized, front, 0.56”

Rear Shock Body, hard anodized, 1.32”

Shock Body, hard anodized, 0.56”

Bleeder Shock Cap, 1:10.

1:10 Blank Shock Pistons

Shock Piston, PTFE (1, 2, 3)

Shock Bushing

FT 1/8” Carbide Diff Balls

Bearing, 3/16 X 5/16, flanged

Bearing, 3/16 x 5/16

FT Blue Aluminum Screw Kit, RC10

FT 4-40 Aluminum Locknut, Blue Anodized

FT 8-32 Blue Aluminum Locknut

16T 48P Pinion Gear



















2

1

6

6

1

8

4ea

4

8

2

2

2

1

1

4

1

2

4

1

1

2

12

28

2

14

2

2

2

2

2

2

8

1

6

1

6

2

5

2

2

2

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

921

922

923

954

955

956

957

958

965

966

967

983

984

985

986

987

231

232

233

234

235

236

908

920

:: Long Arm Conversion Parts

1401

1403

1405

6206

6231

6418

6433

6460

FT Titanium Turnbuckle, 1.30”, blue

FT Titanium Turnbuckle, 1.65”, blue

FT Titanium Turnbuckles, 1.875”, blue

Front Suspension Arm, Wide, Composite, black

Front Shock Tower

FT Gold shock shaft, .71”

Shock Kit, front, 0.71”

Shock Shaft, .71”

:: Reedy Motors and ESC’s

Sonic 540 Mach 2 21.5 Competition Brushless Motor






Replacement Rotor 540-SL

540-SL Brushless Motor 3300kV




Sonic 540 Stock Rotor 12.3 x 24.2 (7.25)



Sonic 540 Modified Rotor 12.2 x 25.0 (5.0)


Reedy 540-SL 3300kV/XP SC700-BL ESC Combo








:: Reedy Motors

(not recommended for RC10 Classic)

237

238

239

240

241

242

243

244

245

246











2

2

1

2

2

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

:: Reedy Accessories

610

651

654

655

656

658

659

660

661

663

247

248

249

250

604

606

607

609

664

716

962

974

975

978

979

980

981

982

992

Sonic 540 Mach 2 Sensor w/bearing

Sonic 540 Mach 2 Steel Bearing Set

Sonic 540 Mach 2 Ceramic Bearing Set

Sonic 540 Mach 2 Insulator Set

526-S AC/DC 2S-6S LiPo/LiFe Charger

Charge Harness 2S Saddle Pack 4mm

Charge Harness 2S Standard Pack 4mm

TAM to DEANS® charge adapter

447-S AC/DC NiMH Peak Charger

Battery Bars (8)

4.0mm plugs (2M, 2F)

4.0mm plugs (2M, 10F)

4.0mm plugs (10F)

4.0mm plugs (10M)

4.0mm plugs (30M)

3.5mm plugs (3M, 3F)

3.5mm plugs (10F)

3.5mm plugs (10M)

3.5mm plugs (30M)

Reedy 09 Decal Set

Sonic 540 Case Screws (3 pcs.)

540-SL/550-SL Steel Bearing Set

540-SL/550-SL Ceramic Bearing Set

Flat Sensor Wire 70mm





Sonic 540 Rotor Spacers

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

:: Qualifier Series Vehicles

7052

20111

20119

20510

30112

:: 1/18 Kits and RTR’s

20103

20121

RC18B2 - RC18T2 Team Kit

SC18 RTR Brushless (ready-to-run)

29

Pro Lite 4x4 RTR, 1/10 Scale (ready-to-run)

Rival Mini Monster Truck 1/18 Scale (ready-to-run)

APEX Mini Touring RTR

RIVAL Electric Monster Truck RTR, 1/8 Scale

(ready-to-run)

APEX Touring V-Type, 1/10 Scale (ready-to-run)

1

1

1

1

1

1

1

:: Reedy Batteries

694

695

700

730

731

732

734

735

736

738

302

309

602

637

681

682

683

684

689

693

AA Alkaline 1.5V (4)

LiPo 65C 7000mAh 7.4V

LiPo 65C 4100mAh 7.4V Shorty

LiPo TX Battery - M11X 2500mAh 7.4V

Wolfpack 2400mAh 7.2V w/DEANS® connector




R-Power 1700mAh 7.2V w/TAM connector

Wolfpack 2400mAh 7.2V w/TAM connector




Wolfpack LiPo 3000mAh 7.4V 25C w/DEANS®





Wolfpack LiPo 5000mAh 7.4V 25C

Wolfpack LiPo 3800mAh 7.4V 25C Shorty

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

:: 1/12, 1/10 Kits and RTR’s

7050

7093

8020

8022

9040

9041

9042

9050

9062

30101

2042

4020

6001

7025

7029

7030

7038

7039

7046

7048

7049

30108

90005

90006

90010

Nitro TC3 RTR Plus (ready-to-run)

FT 12R5.2 Kit

RC10 Classic Kit

FT RC10T4.2 Kit

SC10 Associated/RC10.com Truck RTR (ready-to-run)

SC10 KMC Wheels Race Truck RTR (ready-to-run)

FT SC10.2 Kit

RC10T4.2 RS RTR 2.4GHz Brushless (ready-to-run)

SC10 RS RTR, Lucas Oil (ready-to-run)

SC10 RS RTR, Pro Comp (ready-to-run)

SC10 RS RTR, Rockstar/Makita (ready-to-run)

SC10 RS RTR, Hart and Huntington (ready-to-run)

SC10GT RTR (ready-to-run)

FT RC10R5 Kit

FT RC10R5.1 Kit

FT RC10B4.1 Worlds Kit

FT RC10B4.2 Kit

RC10B4.2 RS RTR 2.4GHz Brushless (ready-to-run)

SC10B RS RTR (ready-to-run)

FT B44.2 4WD Buggy Kit

TC4 Club Racer 4WD Touring Car Race Roller

FT TC6.1 WC 4WD Touring Car Kit

SC10 4x4 Lucas Oil RTR (ready-to-run)

SC10 4x4 Pro Comp RTR (ready-to-run)

SC10 4x4 FT Kit

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

30

:: 1/8 Kits and RTR’s

20501

20502

20503

20504

80906

80907

80908

80909

80912

80933

80934

MGT 4.60 SE RTR (ready-to-run)

MGT 8.0 Nitro RTR (ready-to-run)

Limited Edition MGT 4.60 Nitro RTR, w/flag body


Limited Edition MGT 8.0 Nitro RTR, w/flag body


RC8.2 Nitro Buggy FT Kit

RC8.2e Electric Buggy FT Kit

RC8.2e Electric Buggy RTR (ready-to-run)

RC8.2RS Nitro Buggy RTR (ready-to-run)

RC8T Championship Edition

SC8.2e Short Course Race Truck, Rockstar/Makita

Electric RTR (ready-to-run)

SC8.2e Short Course Race Truck, Slick Mist Electric

RTR (ready-to-run)

1

1

1

1

1

1

1

1

1

1

1

:: RePlay Cameras

RP001

RP002

RP021

RP022

RP023

RP029

RP030

RP032

RP033

RP034

RP036

RP038

RP041

RP042

RP043

RP044

RP045

RP046

RP047

RP048

RP049

RP054

Replay XD1080 Complete Camera System

Replay XD720 Complete Camera System

Replay XD1080 Lens Bezel Kit

Replay XD1080 Clear Lens Cover

Replay XD1080 Lens Bezel & Rear Cap O-Ring

Replay XD1080 HDMI to Mini-HDMI

Replay XD1080 Mini 8-pin USB Charge Data Cable

USB DC Car Charger 1A Stubby

USB DC Car Charger 500mAh

Micro SDHC USB Reader

3M VHB 4991 Mount Adhesive for SnapTray

3M VHB 5962 Mount Adhesive for SnapTray

Replay XD Suction Cup Arm Mini Clamp

Replay XD Suction Cup Short Arm Base

Replay XD Skateboard Mount

Replay XD VHB SnapTray, Convex

Replay XD VHB SnapTray, Flat

Au Plug for Universal DC Wall Charger

Eu Plug for Universal DC Wall Charger

Uk Plug for Universal DC Wall Charger

Universal USB DC Wall Charger 1A

Replay ReView Field Monitor

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1719

1737

3718

3719

3720

3987

6429

6956

7494

7709

1663

1664

1665

1666

1667

1668

1669

1670

1671

1672

1673

1674

1590

1592

1655

1656

1657

1658

1659

1660

1661

1662

1548

1553

1554

1561

1562

1563

1564

1565

1567

1589

1111

1449

1541

1542

1543

1544

1545

1546

1547

:: Tools

FT Turnbuckle Wrench

FT Off Road Ride Height Gauge

FT Hex Driver Set, (7 pcs)

FT .050” Silver Hex Driver

FT 1/16” Black Hex Driver

FT 1.5mm Purple Hex Driver

FT 5/64” Blue Hex Driver

FT 3/32” Gold Hex Driver

FT 2.5mm Green Hex Driver

FT 3mm Red Hex Driver

FT Phillips Silver Screwdriver

FT Silver Spring Hook Tool

FT Nut Driver Set, (6 pcs)

FT 3/16” Black Nut Driver

FT 1/4” Red Nut Driver

FT 5.5mm Red Nut Driver

FT 11/32” Green Nut Driver

FT 8mm Gold Nut Driver

FT 5/64” Blue Ball Hex Driver

FT 3/32” Gold Ball Hex Driver

FT Ball Hex Driver Set, (3 pcs)

FT 8-Piece 1/4” Hex Drive Set

FT 1/4” Hex Drive Handle, without tips

FT 1/4” Hex Drive .050” Tip

FT 1/4” Hex Drive 1/16” Tip

FT 1/4” Hex Drive 5/64” - 2.0mm Tip

FT 1/4” Hex Drive 3/32” Tip

FT 1/4” Hex Drive 1.5mm Tip

FT 1/4” Hex Drive 2.5mm Tip

FT 1/4” Hex Drive 3/16” Nut Driver Tip



FT 1/4” Hex Drive 5.5mm Nut Driver Tip



FT 1/4” Hex Drive 5/64” - 2.0mm Ball End Tip

FT 1/4” Hex Drive 3/32” Ball End Tip

FT 1/4” Hex Drive Standard Screwdriver Tip

FT 1/4” Hex Drive Phillips Screwdriver Tip

FT 1/4” Hex Drive 2.5mm Ball End Tip

FT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm,

1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)

FT Camber + Track Width Tool

FT Body Scissors

12 Inch Nylon Wire Ties



FT Droop Gauge

Shock Building Tool

Molded Tools, Set

V2 Stamped Multi-tool


1

1

12

12

12

1

1

1

1

12

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

SP70**

SP71**

SP73**

SP74**

SP75**

SP76**

SP77**

SP78**

SP79**

SP84**

SP85**

SP86**

SP87**

SP411S

SP411L

SP413S

SP413L

SP416

SP417

SP418

SP420**

SP421S

SP421L

SP422S

SP422L

SP423S

SP423L

SP424S

SP424L

715

110684

:: Apparel

SP36**

SP37**

SP38

SP39

SP66**

SP67**

SP68**

SP69**

Reedy 09’ Black T-Shirt (M, XL, 2XL)

Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL)

Reedy Trucker Hat

Reedy Patch

Stencil Blue T-Shirt (S, M, L, XL, 2-6XL)

AE Stencil Gray Sweatshirt (S, M, L, XL, 2XL, 3XL)

AE Stencil Blue T-Shirt (M, L, XL)

AE 26 Time World Championship T-Shirt, Black

(S, M, L, XL, 2XL, 3XL)

Associated Windbreaker (XL)

Associated Winter Jacket (M, L, XL)

AE Long Sleeve T-Shirt (S, M, L, XL, 2XL)

AE White T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)

AE Blue T-Shirt (S, M, L, XL, 2XL, 4XL, 6XL)

AE Black T-Shirt (S, M, L, XL, 2XL, 3XL)

AE 2012 T-Shirt, Blue (S, M, L, XL, 2XL, 3XL)

AE 2012 T-Shirt, White (S, M, L, XL, 2XL, 3XL)

AE 2012 T-Shirt, Black (S, M, L, XL, 2XL, 3XL)

Reedy 3D T-Shirt, Black (S, M, L, XL, 2XL, 3XL)

Reedy Zip Hoodie, Black (S, M, L, XL, 2XL, 3XL)

Reedy Girl’s 3D T-Shirt, Black (S, M, L, XL)

AE 2013 Zip Hoodie (S, M, L, XL, 2XL, 3XL)

AE Hat 11’ Flat Bill Black S/M

AE Hat 11’ Flat Bill Black L/XL

26 Time World Championship Hat S/M

26 Time World Championship Hat L/XL

Associated Car Carrier Bag, Medium

1/10 FT Motor Bag

Factory Team 1/10 Car Carrier Bag

AE Pit Gloves (L, XL)

AE 2012 Hat, Black, Flat Bill, S/M

AE 2012 Hat, Black, Flat Bill, L/XL

AE 2012 Hat, Black, Curved Bill, S/M

AE 2012 Hat, Black, Curved Bill, L/XL

AE 2012 Hat, White, Flat Bill, S/M

AE 2012 Hat, White, Flat Bill, L/XL

AE 2012 Hat, White, Curved Bill, S/M

AE 2012 Hat, White, Curved Bill, L/XL

Reedy 2009 Track Banner

Team Associated Track Banner

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Pr.

1

1

1

1

1

1

1

1

1

1

1

1

1

Steering / Servo Horn

Steering Rack

Driver: Date:

Track: Event:

Conditions: Indoor Outdoor Temp. Rev.1

Ride Height / Wheelbase

Servo Horn:

AE #89007

Front

Ride

Height:

Rear

Ride

Height:

24mm 24mm

Front Suspension

1 3

2

Camber:

Toe:

Steering Block:

Inline

Trailing

15mm radius

-1°

0°

Caster:

15°

30°

Rear Suspension

Camber:

6 9

2 5 8

1 4 7

Wheelbase:

Short

Long

-1°

A B C D

Rear Hub

Carriers:

0°

1.5°

Front Shocks

Spring: Piston:

Shock

30wt

Electronics

Motor & Wind:

Gear:

Batteries:

Weight

Battery Placement:

Ballast Weight:

Notes:

Front Tires

Tire:

Compound:

#2

0

81T

Standard, full length

Race and Vehicle Comments

Qualify:

Comments:

Pro Line Edge

N/A Stock

Rear Shocks


Shock

30wt

Radio / ESC Settings

Radio:

Throttle / Brake e.p.a:

Throttle / Brake expo:

Servo:

ESC:

ESC Settings:

Other

Body Type:

Wing Type:

ProTech

RC10 Small Wing

Rear Tires

Tire:

Compound:

Pro Line Champion

N/A

#2

2

Stock

Track Info

Surface:

Dirt

Carpet

Astro

Multi

Traction:

Low

Med

High

Conditions:

Grooved

Dusty

Smooth

Bumpy

Hard Pack

Loamy

Moisture:

Wet

Damp

Dry

:: For more setups, visit RC10.com and click on “Setup Sheets”

32

:: Hardware - 1:1 Scale View

Cap Head (shcs)

4-40x1/4 (6285)

4-40x5/16” (6932)

(4145, aluminum)

4-40x3/8 (6924) w/hole (6929)

4-40x1/2 (6925) w/hole (6916)

4-40x5/8 (6926)

4-40x3/4 (6927)

4-40x1 (6928)

Flat Head (fhcs)

Flat Head (fhps)

Bushings

Set Screws

Oilite Bushing Set (6630)

1/4 x 3/8 x 1/8 Flanged

3/16 x 5/16 x 1/8 Flanged

3/16 x 5/16 x 1/4 Flanged

Clips

Diff Balls

4-40x3/8 (6292)

4-40x1/2 (6922)

8-32x1/4 (6931)

Button Head (bhcs)

0-80x3/16 (6613)

4-40x3/16 (6920)

4-40x1/4 (6288)

4-40x3/8 (6917)

3x6mm (31531)

8-32x1/2 (6280)

8-32x7/8 (6281)

4-40x1/8 (6951)

4-40x5/16 (4436)

Nuts (lock/plain)

4-40 Steel Locknut (6242)

E-clip 1/8 (6299)

4-40 Nuts (6295)

4-40 Small Pattern

Plain Nut (7260)

5-40 Diff Locknut (6629)

Bowed E-Clip (6604)

8-32 Nylon Nut, White (6282)

1/8 Diff Balls (6626)

8-32 Steel Locknut (6952)

Notes:

Shims and Washers

Dogbone spacer (6372)

.030 Nylon Spacer (4187)

#4 Washer (6936)

1/4” Axle Shim (6373)

Diff Thrust Washers (6627)

5mm x 9.5mm 0.17mm (6604)

#8 Aluminum Thick

Washer (3323)

Steering / Servo Horn

Steering Rack

Driver: Date:

Track: Event:

Conditions: Indoor Outdoor Temp. Rev.1

Ride Height / Wheelbase

Servo Horn:

Front

Ride

Height:

Rear

Ride

Height: radius

Front Suspension

Wheelbase:

Short

Long

Rear Suspension

Camber:

Camber:

Toe:

Rear Hub

Carriers:

0°

1.5°

1 3

2

Steering Block:

Inline

Trailing

Caster:

15°

30°

3 6 9

2 5 8

1 4 7

A B C D

Front Shocks


Shock

Electronics

Motor & Wind:

Gear:

Batteries:

Weight

Battery Placement:

Ballast Weight:

Notes:

Front Tires

Tire:

Compound:

Rear Shocks


Shock

Radio / ESC Settings

Radio:

Throttle / Brake e.p.a:

Throttle / Brake expo:

Servo:

ESC:

ESC Settings:

Other

Body Type:

Wing Type:

Rear Tires

Tire:

Compound:

Race and Vehicle Comments

Qualify:

Comments:

Track Info

Surface:

Dirt

Carpet

Astro

Multi

Traction:

Low

Med

High

:: For more setups, visit RC10.com and click on “Setup Sheets”

Conditions:

Grooved

Dusty

Smooth

Bumpy

Hard Pack

Loamy

Moisture:

Wet

Damp

Dry

Associated Electrics 6001 Assembly And Operating Instructions Manual

:: Introduction

:: KIT Features

:: Additional

:: Other Helpful Items

:: Table of Contents

:: Notes

:: Nose Plate / Steering Build - Bag A-AA - Step 1

:: Nose Plate / Steering Build - Bag A-AA - Step 2

:: Front Suspension Build - Bag B - Step 1

:: Front Suspension Build - Bag B - Step 2

:: Front Suspension Build - Bag B - Step 3

:: Front Suspension Build - Bag B - Step 4

:: Transmission Build - Bag C-CC - Step 1

:: Transmission Build - Bag C-CC - Step 2

:: Transmission Build - Bag C-CC - Step 3

:: Transmission Build - Bag C-CC - Step 4

:: Transmission Build - Bag C-CC - Step 5

:: Transmission Build - Bag C-CC - Step 6

:: Transmission Build - Bag C-CC - Step 7

:: Transmission Build - Bag C-CC - Step 8

:: Transmission Build - Bag C-CC - Step 9

:: Transmission Build - Bag C-CC - Step 10 :: Rear Bulkhead Build - Bag D-DD - Step 1

:: Rear Bulkhead Build - Bag D-DD - Step 2

:: Rear Bulkhead Build - Bag D-DD - Step 3

:: Rear Bulkhead Build - Bag D-DD - Step 4

:: Rear Suspension Build - Bag E-EE - Step 1

:: Rear Suspension Build - Bag E-EE - Step 2

:: Rear Suspension Build - Bag E-EE - Step 3

:: Turnbuckles Build - Bag F - Step 1

:: Turnbuckles Build - Bag F - Step 2

:: Turnbuckles Build - Bag F - Step 3

:: Turnbuckles Build - Bag F - Step 4

:: Shocks Build - Bag G-GG - Step 1

:: Shocks Build - Bag G-GG - Step 2

:: Shocks Build - Bag G-GG - Step 3

:: Shocks Build - Bag G-GG - Step 4

:: Shocks Build - Bag G-GG - Step 5

:: Shocks Build - Bag G-GG - Step 6

:: Shocks Build - Bag G-GG - Step 7

:: Chassis Build - Bag H - Step 1

:: Electronics Build - Bag I - Step 1

:: Electronics Build - Bag I - Step 2

:: Electronics Build - Bag I - Step 3

:: Electronics Build - Bag I - Step 4

:: Electronics Build - Bag I - Step 5

:: Electronics Build - Bag I - Step 6

:: Wheels / Tires and Body - Bag J - Step 1

:: Wheels / Tires and Body - Bag J - Step 2

:: Wheels / Tires and Body - Bag J - Step 3

Painting Tips:

:: Wheels / Tires and Body - Bag J - Step 4

Light Buckets:

:: Wheels / Tires and Body - Bag J - Step 5

Painting Tips:

:: Wheels / Tires and Body - Bag J - Step 6

:: Wheels / Tires and Body - Bag J - Step 7

:: Wheels / Tires and Body - Bag J - Step 8

:: Tuning Tips

:: Tuning Tips (cont.)

:: Shocks

:: Springs

:: Slipper / Gear Cover

:: Shock Fluid

:: Turnbuckles / Servo

:: Steering

:: Antenna Mount / Battery Strap

:: Front Arm

:: Rear Arm

:: Front Shock Tower

:: Rear Shock Tower

:: Wheels / Tires

:: Rear Bulkhead

:: Transmission

:: Chassis

:: Lubes & Adhesives / Misc.

:: Body, Wing, and Decals

:: XP Electronics

:: Factory Team and Option Parts

:: Long Arm Conversion Parts