Sharp HTSB200 - Sound Bar Speaker Specifications

SOUND BAR SYSTEM
MODEL
HT-SB200
OPERATION MANUAL
is a trademark of SRS Labs, Inc.
WOW HD technology is incorporated under license from
SRS Labs, Inc.
Note:
This product is recommended for flat panel TV
(LCD and plasma).
Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
HT-SB200
Special notes
Features
WARNINGS
SRS WOW improves the dynamic audio performance of
compressed and uncompressed audio by expanding the size of
the audio image and creating a deep, rich bass response.
● When the ON/STAND-BY button is set at STAND-BY
Important Instruction
●
●
●
●
●
●
position, main voltage is still present inside the speaker.
When the ON/STAND-BY button is set at STAND-BY
position, the speaker may be brought into operation by the
remote control.
This speaker contains no user serviceable parts. Never
remove covers unless qualified to do so. This speaker
contains dangerous voltages, always remove mains plug
from the socket before any service operation and when not in
use for a long period.
The supplied AC/DC adaptor contains no user serviceable
parts. Never remove covers unless qualified to do so.
It contains dangerous voltages, always remove mains plug
from the main outlet socket before any service operation or
when not in use for a long period.
The AC/DC adaptor supplied with the HT-SB200 must not be
used with other equipment.
Never use an AC/DC adaptor other than the one specified.
Otherwise, problems or serious hazards may be created.
To prevent fire or shock hazard, do not expose this appliance
to dripping or splashing. No objects filled with liquids, such as
vases, shall be placed on the apparatus.
Do not turn the volume on to full at switch on. Listen to music
at moderate levels.
2
HT-SB200_A6_EN.fm
2008 December 16
Accessories
Contents
HT-SB200
Please confirm that only the following accessories are included.
Page
Remote control
x1
RCA cable
Spike x 4
(2 pins - 2 pins) x 1 (Length : 25 mm)
AC/DC adaptor
x1
AC power lead x 1 AC power lead x 1
(for Australia only)
AC power lead x 1
(for United
Wall mount angle
Kingdom and Eire
x2
only)
■ Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . 14 - 15
Foot cushion x 4
Nut
Pattern paper x 1
(Spike + Nut) x 4
(Length : 30 mm)
■ Preparation for Use
Speaker preparation . . . . . . . . . . . . . . . . . . . . 8 - 10
Placing the speaker . . . . . . . . . . . . . . . . . . . . . . . . 11
Falling prevention . . . . . . . . . . . . . . . . . . . . . . . . . 11
Speaker connections to TVs . . . . . . . . . . . . . . . . 12
AC power connection . . . . . . . . . . . . . . . . . . . . . . 13
Remote control . . . . . . . . . . . . . . . . . . . . . . . 13 - 14
Plug adaptor x 1
(for Philipines
only)
■ References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . 16
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Error indicators and warnings . . . . . . . . . . . . . . . 17
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
General Information
■ General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Controls and indicators . . . . . . . . . . . . . . . . . . 5 - 7
Note:
The AC/DC adaptor may be different from the one in the
drawing.
3
2009 January 23
HT-SB200_A6_EN.fm
HT-SB200
Precautions
■ General
● Please ensure that the equipment is positioned in a well-
ventilated area and ensure that there is at least 10 cm (4") of
free space along the sides and top of the equipment.
10 cm (4")
10 cm (4")
10 cm (4")
● Do not remove the outer cover, as this may result in
●
●
General Information
●
●
● Use the speaker on a firm, level surface free from vibration.
● Keep the speaker away from direct sunlight, strong magnetic
●
●
●
●
●
●
●
●
fields, excessive dust, humidity and electronic/electrical
equipment (home computers, facsimiles, etc.) which
generate electrical noise.
Do not place anything on top of the speaker.
Do not expose the speaker to moisture, to temperatures
higher than 60˚C (140˚F) or to extremely low temperatures.
If your system does not work properly, disconnect the AC
power lead from the wall socket. Plug the AC power lead back
in, and then turn on your system.
In case of an electrical storm, unplug the speaker for safety.
Do not use an external power supply other than the 12V DC
supplied with this speaker as it may be damaged.
SHARP is not responsible for damage due to improper use.
Refer all servicing to a SHARP authorised service centre.
Hold the AC power plug by the head when removing it from
the wall socket, as pulling the lead can damage internal
wires.
The AC power plug is used as a disconnect device and shall
always remain readily operable.
4
HT-SB200_A6_EN.fm
2008 December 22
●
electric shock. Refer internal service to your local
SHARP service facility.
The ventilation should not be impeded by covering the
ventilation openings with items, such as newspapers,
tablecloths, curtains, etc.
No naked flame sources, such as lighted candles, should be
placed on the apparatus.
Attention should be drawn to the environmental aspects of
battery disposal.
This speaker should only be used within the range of
5˚C - 35˚C (41˚F - 95˚F).
The apparatus is designed for use in moderate climates.
Warning:
The voltage used must be the same as that specified on this
speaker. Using this product with a higher voltage other than that
which is specified is dangerous and may result in a fire or other
type of accident causing damage. SHARP will not be held
responsible for any damage resulting from use of this speaker
with a voltage other than that which is specified.
■ Volume control
The sound level at a given volume setting depends on speaker
efficiency, location, and various other factors. It is advisable to
avoid exposure to high volume levels. Do not turn the volume on
to full at switch on. Listen to music at moderate levels.
Controls and indicators
HT-SB200
12
3
45
STANDARD
CINEMA / GAME
SPORT
NEWS
VOL.
SURROUND FUNCTION
SOUND BAR SYSTEM HT-S8200
6 7 8 9 10 11
12 13
14
14
13 15
General Information
ON/STAND-BY
■ Front Panel
1.
2.
3.
4.
5.
6.
7.
8.
Reference page
Sport Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Standard Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . 15
Information Display . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cinema/Game Indicator . . . . . . . . . . . . . . . . . . . . . 15
News Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . 14
Volume Down Button . . . . . . . . . . . . . . . . . . . . . . . 14
Volume Up Button . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9.
10.
11.
12.
13.
14.
15.
Reference page
Surround Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Function Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Remote Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Left Front Speaker
Bass Reflex Duct
Subwoofers
Right Front Speaker
5
2008 December 16
HT-SB200_A6_EN.fm
HT-SB200
Controls and indicators (continued)
General Information
1
■ Rear Panel
1.
2.
3.
2
3
Reference page
Audio Line In 2 (3.5 mm stereo/headphone)
Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Line In 1 (RCA/cinch) Sockets . . . . . . . . . . . . . . . . 12
DC Input Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6
HT-SB200_A6_EN.fm
2008 December 16
HT-SB200
8
9
10
2
3
4
11
12
13
14
5
6
7
15
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Reference page
Remote Control Transmitter . . . . . . . . . . . . . . . . . . 14
Cinema/Game Button. . . . . . . . . . . . . . . . . . . . . . . . 15
Standard Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Volume Up Button . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Subwoofer Level Down Button . . . . . . . . . . . . . . . . 15
Volume Down Button . . . . . . . . . . . . . . . . . . . . . . . . 14
Bass/Treble Button. . . . . . . . . . . . . . . . . . . . . . . . . . 15
On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
Sport Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
News Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Subwoofer Level Up Button . . . . . . . . . . . . . . . . . . 15
Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Mute Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Line Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
TV Operation Buttons . . . . . . . . . . . . . . . . . . . . . . . . 7
TV Operation Buttons (Only SHARP TV):
Remote
control
Plastic shield
On/Stand-by
Button
Sets the TV
Input Select
power to “ON” Button (TV)
or “STANDBY”.
Press the
button to
switch the
input source.
Volume Up
and Down
Buttons
Turn up/down Channel Up
the TV
and Down
volume.
Buttons
Switch up/
down the TV
channels.
General Information
■ Remote Control
1
Battery holder
Note:
Before using remote control, please remove plastic shield at
battery holder.
Notes:
● Some models of SHARP TV may not be operable.
● SHARP TV remote will not work with HT-SB200 system.
2008 December 16
HT-SB200_A6_EN.fm
7
HT-SB200
Speaker preparation
Make sure to unplug the AC power lead before installing
the speaker or changing the position.
Using foot cushions
Select from three installation methods according to the
preferred position.
Preparation for Use
Using spikes
You may choose from the two different spike lengths provided:
25 mm and 30 mm.
Nuts (secured on 30 mm spikes) must be used when installing
either the 25 mm or 30 mm spikes.
The speaker can be leveled by adjusting the spikes and nuts.
Option 2
Option 1
Attach foot cushions as shown
Option 1
Note:
Option 1 or option 2 foot cushion positions based on LCD TV
stand.
Tighten all spikes as shown
8
Option 2
Notes:
● Option 1 or option 2 indicates spike positions based on LCD
TV stand.
● When attaching the spikes, place the speaker on a cushion
or soft cloth to avoid damage.
Caution:
When using these spikes on glossy or slippery table such as on
glass top, stick foot cushions at the bottom of the spikes to avoid
slippage.
HT-SB200_A6_EN.fm
2008 December 16
HT-SB200
Caution:
● Be very careful to prevent the speaker [1.75 kg (3.86 lbs.)]
●
●
●
●
●
■ Wall mount angle fixed to the wall
(Horizontal position)
1
from falling when mounting on the wall.
Before mounting, check the wall strength. (Do not put on the
veneer plaster or whitewashed wall. The speaker may fall.) If
unsure, consult a qualified service technician.
Mounting screws are not supplied. Use appropriate ones.
Check all wall mount angle screws for looseness.
Select a good location. If not, accidents may occur or the
speaker may get damaged.
SHARP is not responsible for accidents resulting from
improper installation.
■ Driving screws
44 mm
509 mm
Wall surface
29 mm
44 mm
Pattern paper
29 mm
2
SHARP designed the speakers so you may hang them on the
wall. Use proper screws (not supplied). See below for size and
type.
Make a hole on the wall following the screw point
marks on the pattern paper by using a drill.
32 mm (1-1/4")
8-9 mm (3/8")
3.2 mm (1/8")
5 mm
(3/16")
Fix the pattern paper to the wall in horizontal position
as below.
Wall surface
9 mm (3/8")
Min. 22 mm (7/8")
3
Preparation for Use
To mount the speaker on the wall
Fix a wall mount plug into the hole using a hammer,
until it is flush with the wall surface.
32 mm (1-1/4")
8-9 mm (3/8")
Wall surface
Continued to the next page
9
2008 December 16
HT-SB200_A6_EN.fm
HT-SB200
Speaker preparation (continued)
4
Screw the wall mount angle to the wall as shown in the
illustration. (Total screw is 8 pieces)
Wall mount angle
Wall surface
■ Installing the speaker
1
Align the wall mount slot at the speaker to the wall
mount angle.
2
3
Slot the speaker into the wall mount angle.
Fix them securely.
Preparation for Use
Wall mount angle
(screws x 4)
(screws x 4)
Wall surface
Wall mount angle
Wall surface
Note:
Make sure all screws are fully tighten. (screws are not supplied)
10
HT-SB200_A6_EN.fm
2008 December 16
Wall surface
Placing the speaker
Falling prevention
Installation image:
Safety wires (not supplied) are useful to prevent the speaker
from falling off the table.
HT-SB200
VCR
Preparation for Use
TV
DVD player
Place the speaker as shown.
Notes:
● As the sound from the speaker is omni-directional, you can
place the speaker anywhere you like. However, it is
recommended to place it as close to the TV as possible.
● The front panel of the speaker is not removable.
Caution:
● Do not change the installation direction when the speaker is
turned on.
● Do not stand or sit on the speaker as you may be injured.
Loop the safety wires (not supplied) into each hole as shown and
tie the safety wires to the LCD TV stand.
11
2008 December 16
HT-SB200_A6_EN.fm
HT-SB200
Speaker connections to TVs
Preparation for Use
Caution:
Turn off all other equipment before making any connections.
Tuner receiving for other audio system
● Placing the aerial near the speaker AC power lead may cause
noise pick up. Place the aerial away from the speaker for
better reception.
■ Connecting to a TV (with Headphone socket)
If the TV/monitor has headphone socket, connect it to the
AUDIO LINE IN 2 socket on the rear of the speaker.
TV
Notes:
● To connect to TV, use either LINE IN 1 sockets or AUDIO
LINE IN 2 socket only.
● Refer the operation manual of the equipment to be
connected.
● Fully insert the plugs to avoid fuzzy pictures or noises.
HEADPHONE
To HEADPHONE socket
■ Connecting to a TV
Audio cable
(3.5 mm/stereo socket)
(not supplied)
If the TV/monitor has an audio output, connect it to the LINE IN
1 sockets on the rear of the speaker.
TV
To AUDIO LINE
IN 2 socket
Speaker
To audio output sockets
Notes:
RCA cable (supplied)
● If the TV volume is continuously in low level, the speaker will
To LINE IN 1
sockets
automatically power off. Increase the TV output volume to
enjoy the sound from the speaker.
● If the speaker volume is continuously in very high level, the
speaker will mute and recover after 3 seconds.
Speaker
12
HT-SB200_A6_EN.fm
2008 December 16
AC power connection
Remote control
After checking all the connections have been made correctly,
connect the AC power lead to the AC power input socket, then
to the wall socket.
■ Battery installation
1 Insert pin into the hole as shown and pull to open the
1
2
Plug the AC power lead into the AC/DC adaptor.
3
Plug the AC power lead into a wall socket. The
STAND-BY indicator will turn RED when AC power is
applied. The power indicator will turn GREEN when
the system in “ON”.
Plug the AC/DC adaptor cable into the DC IN socket
on the speaker.
2
AC/DC Adaptor Cable
DC IN socket
(DC 12V)
battery holder.
Pin
Back of
remote control
2 Remove the old battery from the battery holder, insert
the new battery and then slide the battery holder back
into the remote control.
Battery holder
Battery type
Locking tab
Polarity (+) symbol
Positive (+) side up
AC power lead
Preparation for Use
■ Using with the AC/DC adaptor
HT-SB200
1
3
AC/DC Adaptor
Precautions for battery use:
Wall socket
(AC 100 - 240 V ~ 50/60 Hz)
Notes:
● Unplug the AC/DC adaptor from the wall socket if the
speaker will not be used for a long period of time.
● Use only the supplied AC/DC adaptor. Using other AC/DC
adaptor may cause an electric shock or fire.
● Remove the battery if the speaker will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
13
2008 December 16
HT-SB200_A6_EN.fm
Preparation for Use
HT-SB200
Remote control (continued)
Caution:
● Do not use rechargeable battery (nickel-cadmium battery, etc.).
● Danger of explosion if battery is incorrectly replaced.
● Replace only with the same or equivalent type.
● Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
● Installing the battery incorrectly may cause the speaker to
malfunction.
Notes concerning use:
● Replace the battery if the operating distance is reduced or if
the operation becomes erratic. Purchase “CR 2025”, coin
lithium battery.
● Periodically clean the transmitter on the remote control and
the sensor on the speaker with a soft cloth.
● Exposing the sensor on the speaker to strong light may
interfere with operation. Change the lighting or the direction
of the speaker if this occurs.
● Keep the remote control away from moisture, heat, shock,
and vibrations.
■ Test of the remote control
Point the remote control directly at the remote sensor on the
speaker.
The remote control can be used within the range shown
below:
Press the ON/STAND-BY button. Does the power turn on? Now,
you can enjoy your system.
Remote sensor
STANDARD
NEWS
ON/STAND-BY
VOL.
CINEMA / GAME
SPORT
ON/STAND-BY
NEWS
VOL.
SURROUND FUNCTION
SOUND BAR SYSTEM HT-SB200
■ To turn the power on
Press the ON/STAND-BY button.
● The power indicator turns green. If the power does not turn
on, check whether the power lead is plugged in properly.
To set the speaker to stand-by mode:
● Press the ON/STAND-BY button again.
The STAND-BY indicator turns red.
■ Display brightness control
Press the DIMMER button to adjust the brightness of the display
and sound mode indicator.
Sound mode indicator and display bright
Sound mode indicator and display dim
■ Volume auto fade-in
SURROUND FUNCTION
SOUND BAR SYSTEM HT-SB200
15˚ 15˚
STANDARD
Sound mode indicator and display off. Pressing
any button will light up the display for 3 seconds only.
CINEMA / GAME
SPORT
General control
0.2 m - 6 m
(8” - 20’)
If you turn off and on the speaker with the volume set to 40 or
higher, the volume starts at 20 and fades in to the last set level.
■ Volume control
Speaker operation:
Press volume up (VOL. + ) to increase
the volume and press volume down
(VOL. – ) to decrease the volume.
14
HT-SB200_A6_EN.fm
2008 December 16
00
01
02 .....
59
60
HT-SB200
Remote control operation:
Press the VOL + button to increase the volume and the VOL –
button to decrease the volume.
■ Muting
The volume is muted temporarily when pressing
the MUTE button on the remote control. Press
again to restore the volume.
SPORT
NEWS
STANDARD
CINEMA/GAME
WOW HD off
WOW HD on for cinema/game sound effect
SPORT
WOW HD on for sport broadcasting
NEWS
WOW HD on for news
■ Subwoofer level control
The speaker level can be adjusted.
To increase the level, press the
SUBWOOFER LEVEL
button.
To decrease the level, press the
SUBWOOFER LEVEL
button.
+5
-5
-4 ...
4
5
1. Press the BASS/TREBLE button
to select “TREBLE”.
2. Within 5 seconds, press the
VOLUME (+ or –) button to adjust
the treble.
-5
+5
■ Function
When the FUNCTION button on
speaker or LINE button on the remote
control is pressed, the input source
will change. Press the FUNCTION
button on speaker or LINE button on
the remote control repeatedly to
select desired input source.
LINE 1
LINE 2
Note:
The backup function will protect the memorised function mode
for a few hours should there be a power failure or the AC power
lead becomes disconnected.
Auto power on function:
When you press the LINE button on the remote control, the
speaker will turns on at last function.
Auto power off and auto detect signal:
● If no signal is detected for 1 minute during power on, the
speaker will automatically go to stand-by mode. The STANDBY indicator turns orange.
● The speaker will automatically power ON if it detects audio
signal from connected equipment.
Note:
When sound from the speaker is distorted, decrease the
subwoofer level.
Basic Operation
Main unit operation:
When the SURROUND button is pressed, the current mode
setting will light up. To change to a different mode, press the
SURROUND button repeatedly until the desired sound mode
lights up.
Remote control operation:
Press a desired sound mode on the remote control.
CINEMA/GAME
-5
■ Treble control
■ Preset sound mode
STANDARD
■ Bass control
1. Press the BASS/TREBLE button
to select “BASS”.
2. Within 5 seconds, press the
VOLUME (+ or –) button to adjust
the bass.
15
2008 December 16
HT-SB200_A6_EN.fm
HT-SB200
Troubleshooting chart
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following
before calling your authorised SHARP dealer or service centre.
■ General
Symptom
No sound is heard.
Possible cause
● Is the input signal (selection) set
Symptom
TV cannot be
operated with the
remote control.
References
properly?
● Is the volume level set to “0”?
Noise is heard
during playback.
● Move the speaker away from any
When a button is
pressed, the
speaker does not
respond.
● Set this speaker to the stand-by
The power is not
turned on.
● Is the speaker unplugged? (Refer to
computers or mobile phones.
mode and then turn it back on.
page 13)
● The protection circuit may be
activated. Unplug and plug in the
power lead again after 5 minutes or
more.
■ Remote control
Symptom
The remote control
does not operate
properly.
16
HT-SB200_A6_EN.fm
Possible cause
●
●
●
●
Is the battery polarity correct?
Is the battery dead?
Is the distance or angle incorrect?
Are there any obstructions in front of
the speaker?
● Is there a strong light shining on the
remote sensor?
● Is the remote control for another
equipment used simultaneously?
2008 December 16
Possible cause
The speaker cannot ● Is the AC power lead of the speaker
be turned on with
plugged in?
the remote control. ● Is the battery inserted?
● Depending on the model, some or all
functions may not be operable using
the remote control of this speaker. In
this case, use the remote control
supplied with the TV.
■ Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation inside
the cabinet or on the transmitter on the remote control.
Condensation can cause the speaker to malfunction. If this
happens, leave the power on until normal operation is possible
(about 1 hour). Wipe off any condensation on the transmitter
with a soft cloth before operating the speaker.
■
If problem occurs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
If such a problem occurs, do the following:
1. Set the speaker to the stand-by mode and turn the power on
again.
2. If the speaker is not restored in the previous operation,
unplug and plug in the speaker, and then turn the power on.
Maintenance
Error indicators and warnings
■ Cleaning the cabinet
When you fail to perform operations properly, the following
messages are displayed on the speaker.
Caution:
Display
etc.). It may damage the cabinet finish.
● Do not apply oil to the inside of each component. It may
cause malfunctions.
Meaning
● Malfunction of the surround
● Do not use chemicals for cleaning (petrol, paint thinner,
or
circuit. Place the speaker away
from noise source and plug the
AC power lead into another wall
socket. (*)
or
● When the protection circuit of the
amplifier is activated.
Power indicator (blinks red)
(*): Should the same message appear even if the speaker is
unplugged and plugged in or is set to the stand-by mode
and on again, contact your local dealer where you
purchased the speaker.
References
Periodically wipe the cabinet with a soft cloth.
HT-SB200
17
2008 December 16
HT-SB200_A6_EN.fm
HT-SB200
Specifications
As part of our policy of continuous improvement, SHARP
reserves the right to make design and specification changes for
product improvement without prior notice. The performance
specification figures indicated are nominal values of production
speaker. There may be some deviations from these values in
individual speaker.
Input terminals
■ General
Dimensions
Power source
References
Power
consumption
Output power
Speaker
Audio output
terminals
DC IN 12V
4A: AC/DC adaptor
(AC 100 - 240 V ~ 50/60 Hz)
Power on: 10 W
Power stand-by: 0.6 W (*)
Front speaker:
RMS: 12 W (6 W + 6 W) (10% T.H.D.)
RMS: 9.6 W (4.8 W + 4.8 W) (0.9% T.H.D.)
Subwoofer:
RMS: 20 W (10% T.H.D.)
RMS: 13 W (0.9% T.H.D.)
2.1-way Speaker System
Front Speakers: 38 mm (1-1/2") Full
Range
Subwoofer: 57 mm (2-1/4") Woofer (x4)
Speakers: 12 ohms/channel
Subwoofer: 3 ohms
(12 ohms x 4 parallel connection)
18
HT-SB200_A6_EN.fm
2008 December 16
Weight
Analogue input (LINE 1):
RCA type x 1pair (L/R)
500 mV / 47 kohms
Analogue input (LINE 2):
Stereo mini socket Ø 3.5 mm
100 mV / 47 kohms
Width: 800 mm (31-1/2")
Height: 96 mm (3-3/4")
Depth: 70 mm (2-3/4")
1.75 kg (3.86 lbs.)
(*) This power consumption value is obtained when in the
power stand-by mode.
MEMO
TINSEA290AWZZ
TINSEA282AWZZ
09A R AS 2