HR7012
Rear Seat Video
Headrest System
S
P
HR7012S
S
HR7012
Available in three configurations
• Dual DVD Player DD7012
• Single DVD Player and Monitor DM7012
• Dual Monitor MM7012
Owner’s Manual
2
Table of Contents
Contents
Welcome���������������������������������������������������������������������������������������������������������������������������������������������������������������������1
HR7012 Rear Seat Video Headrest System Configurations����������������������������������������������������������������������2
Product Features������������������������������������������������������������������������������������������������������������������������������������������������������3
Cautions����������������������������������������������������������������������������������������������������������������������������������������������������������������������4
Quick Start Guide����������������������������������������������������������������������������������������������������������������������������������������������������5
General Operating Instructions�������������������������������������������������������������������������������������������������������������������������6
Front Panel Controls�����������������������������������������������������������������������������������������������������������������������������������������������7
Remote Control and Headphone Battery Installation�������������������������������������������������������������������������������9
Battery Cautions and Warnings�����������������������������������������������������������������������������������������������������������������������11
Remote Control Operation�������������������������������������������������������������������������������������������������������������������������������12
System Setup Menu �������������������������������������������������������������������������������������������������������������������������������������������16
System Setup Sub-Menus���������������������������������������������������������������������������������������������������������������������������������18
DVD Playback Settings and Adjustments ���������������������������������������������������������������������������������������������������27
DISC Basics��������������������������������������������������������������������������������������������������������������������������������������������������������������32
Playback of Media������������������������������������������������������������������������������������������������������������������������������������������������33
DVD Region Codes�����������������������������������������������������������������������������������������������������������������������������������������������37
Game Controller Operation������������������������������������������������������������������������������������������������������������������������������38
Troubleshooting���������������������������������������������������������������������������������������������������������������������������������������������������39
Specifications ��������������������������������������������������������������������������������������������������������������������������������������������������������40
Compliance Information������������������������������������������������������������������������������������������������������������������������������������41
User Notes ��������������������������������������������������������������������������������������������������������������������������������������������������������������42
© 2012 Audiovox. All rights reserved. This manual, or any portion thereof,
may not be reproduced without the express written permission of Audiovox.
HR7012 Rear Seat Video Headrest System
Owner’s Manual
HR7012 Rear Seat Video Headrest System
Owner’s Manual
Welcome
Thank you for purchasing the HR7012 Rear Seat Video Headrest System. Before operating this
system read this manual thoroughly and retain it for future reference.
The HR7012 is a versatile Rear Seat Video
Headrest System and is available in three
different configurations (please refer to
page 2 for a detailed description of each
of the configurations). Each of the three
configurations come with two replacement
video monitor headrests referred to as either
“M1” or “M2” in this manual. Both the M1
and M2 feature a 7” Monitor equipped with
easy to use front panel controls and auxiliary
connection options. The system allows the
users to watch the same DVD/Video Source on
both monitors simultaneously or individual
DVD/Video Sources on either monitor.
The full function wireless remote control
operates either monitor by selecting Monitor
Select “M1” or “M2” button.
The HR7012 Rear Seat Video Headrest
System is set-up and adjusted with easy The
HR 7012 Rear Seat Video Headrest System is
set-up and adjusted with easy to use menus
that are accessed using the remote control or
the front panel buttons.
HR7012M: is a 7” LCD monitor with
a built-in DVD player that allows the
user to select from several sources
(DVD/USB, M2, AV-IN, AUX MEDIA,
and GAME* Source). The monitor has
a built-in infrared audio transmitter
channel.
(Optional wired headphones allow the user
to listen to audio from the system through
the 1/8” jack located on the front of each
monitor.)
The supplied two-channel wireless Infrared
(IR) headphones have an A-B switch that
allow the users to select the audio from
either M1 on “CH. A” or M2 on ”CH. B”
•
The M1 monitor will only respond to
the remote control when the Monitor
Select “M1” button is pressed.
•
The M2 monitor will only respond to
the remote control when the Monitor
Select “M2” button is pressed. HR7012S: is a 7” LCD monitor (No
DVD)that allows the user to select
from several sources (M1, AV-IN,
AUX MEDIA, and GAME* Source). The monitor has a built-in infrared
audio transmitter channel.
* GAME Optional
Licensed under one or more of the following patents: Patent NOS. 7,245,274, 6,899,365, and
6,678,892.
1
HR7012 Rear Seat Video Headrest System Owner’s Manual
HR7012 Rear Seat Video Headrest System Configurations
Available in three configurations as follows:
Configuration 1: Model DD7012
Two 7” LCD monitors with a built-in DVD player (HR7012M) (Figure 1.)
HR7012M
(M2)
S
HR7012M
+
(M1)
P
S
P
Figure 1
Configuration 2: Model DM7012
One 7” LCD monitor with a built-in DVD player (HR7012M) and One 7” LCD monitor (screen
only) (HR7012S) (Figure 2.)
NOTE: When the M2 Monitor is set to the M1 source and to “AUTO ON”, M2 will turn ON
automatically when M1 is in playback mode. (See page 26)
HR7012S
(M2)
S
HR7012M
+
(M1)
P
P
S
Figure 2
Configuration 3: Model MM7012
Two 7” LCD monitors (HR7012S) (screens only) connected to automotive head unit (radio)
with built-in DVD player or external DVD, Blu-ray player or other A/V source. (Figure 3.)
NOTE: When the Monitors are set to the “A/V” IN source and “AUTO ON” is selected both
monitors will turn ON automatically when a video signal is received from a external source.
(See page 26)
HR7012S
(M2)
S
P
HR7012S
+
(M1)
S
P
Figure 3
Your system may have an additional A/V (Audio/Video) input such as Configuration 3 above
and/or an optional Game Pack (HR7012GP).
HR7012 New Features:
1.
When an optional Game Pack is installed, either monitor can be designated as “Player 1”. Selection is based on a “first come, first serve” basis. The second monitor will automatically
become “Player 2”.
2.
AUTO “M1 ON” of the HR7012S (M2) monitor(s) when the HR7012M (M1) is first
turned ON. This is done by selecting “M1” in the Default AUTO ON/OFF sub-menu.
(See page 26)
3.
AUTO “ON” of the HR7012S (M2) monitor(s) when a video source is detected. This is done by selecting “ON” in the Default AUTO ON/OFF sub-menu.
(See page 26)
4.
100 Channel FM Modulator.
2
HR7012 Rear Seat Video Headrest System Owner’s Manual
Product Features
The HR7012 Rear Seat Video Headrest
System consists of:
1. T wo factory matched Headrests with
7-inch Color TFT-LCD Display Screen
(800x480) 16:9 aspect ratio. (See
configuration options on previous page)
2. T wo Wireless Infrared (IR) Headphones
equipped with volume control and A/B
switch to select between “M1” and “M2”.
Note: The wireless IR headphones must
be used within a line of sight from the
transmitter as infrared transmission,
like visible light, travels only in an
unrestricted line of sight.
3. T wo Infrared (IR) Transmitters for
listening to audio signal through Wireless
IR Headphones.
4. O
ne wireless FM transmitter used to
listen to audio (M1 only) through the
vehicle’s FM radio by tuning to one of 100
frequencies. Try each station frequency
until you achieve a clear audio signal.
Note: Whenever the FM transmitter
is active, regular radio reception may
be poor. Turn the FM transmitter
off to allow normal radio reception
5. T wo sets of Audio/Video (AUX)
Signal Input Jacks (yellow, white
and red) used to connect items
such as a DVD player, video game
device, or other audio/video devices. Two 1/8-inch (3.5mm) Wired Stereo
Headset Jacks that can be used with any
standard stereo headphones.
6. U
SB Port (HR7012M only) used to connect
a USB memory device (eg. thumb drive) Content on the USB device can be played
by selecting “DVD” as the video source. The USB device will automatically start
up upon connection, thereby overriding
the DVD disc. Disconnect the USB device
to play DVD’s and CD’s.
7. Remote Sensor on the Front Panel.
8. O
ne Full Function Remote Control to
operate either headrest by selecting “M1”
or “M2”.”
9. C
ontrol Buttons on the Front Panel POWER, SOURCE, VOLUME UP/DOWN,
STOP, EJECT, MENU/SELECT.
10. OSD (On Screen Display) menus.
3
HR7012 Rear Seat Video Headrest System Owner’s Manual
CAUTIONS
Important Notice
Safety Precaution
An LCD Panel and/or Video Monitor may be
installed in a motor vehicle and visible to the
driver if the LCD Panel or Video Monitor is
used for vehicle information, system control,
rear or side observation or navigation. If
the LCD Panel or Video Monitor is used for
television reception, video or DVD play, the
LCD Panel or Video Monitor must be installed
so that these features will only function when
the vehicle is in “park” or when the vehicle’s
parking brake is applied.
For safety reasons, when changing a video
disc it is recommended that the vehicle
not be in motion, and that you do not
allow children to unfasten safety belts to
change a disc or make any adjustments to
the system. System adjustments can be
accomplished using the remote control unit,
while safety belts remain fastened. Enjoy
your entertainment system but remember
that the safety of all passengers remains the
number one priority.
An LCD Panel or Video Monitor used for
television reception, video or DVD play that
operates when the vehicle is in gear or when
the parking is not applied must be installed
to the rear of the driver’s seat where it will
not be visible, directly or indirectly, to the
operator of the motor vehicle.
CAUTION
Always run the vehicle’s engine while using
the HR7012 Rear Seat Video Headrest
System. Using this system without running
the engine can result in battery drainage. To avoid the risk of battery drainage, please
remember to turn off the device when the
vehicle is not in use for long periods of time.
4
HR7012 Rear Seat Video Headrest System Owner’s Manual
Quick Start Guide
Turn ON the Monitors (M1 and M2).
1.
Press the Power ON/OFF button. The
power indicator will light up red.
2.
Insert a DVD, CD, MP3 disc into the disc
slot located on top of the M1 monitor
(disc label toward user). Push down
gently on the disc until the player pulls
the disc in (Do Not force disc) or connect
a video source through the jacks on the
front panel.
3.
Tilt the monitor to a comfortable
viewing position. 4.
The supplied wireless IR headphones
have an ”A-B” switch used to select
the audio from either the “M1” or
“M2” monitor. When sitting in front
of the M1 screen, use the CH. A setting. When sitting in front of the M2 screen,
use the CH. B setting. Set the headset
to the proper channel and press the
Power On/Off switch. The power
indicator will light up red. Turn the
volume down to its lowest setting
before putting the headphones on. 5.
When the DVD menu appears, select
the menu item using the UP/DOWN
buttons and press Enter or Play button.
6.
If audio playback through the
vehicle radio is preferred, use the FM
transmitter On/Off button on the
remote control. Set the vehicle radio to
the channel selected on the M1 monitor. If interference with a local radio station
occurs, set the FM modulator to one
of the other 100 radio frequencies
using the Channel Select buttons on
the remote control or front panel.
Note: To operate the M1 screen, press
M1 on the remote control. To operate
the M2 screen, press M2.
7.
To turn OFF either M1 or M2, press and
hold the Power ON/OFF button for 5
seconds or turn the vehicle OFF.
5
HR7012 Rear Seat Video Headrest System Owner’s Manual
General Operating Instructions
For best disc operation , it is important that
you read this section completely.
DVD Region Coding
The HR7012M and the DVD are coded by
region. These region codes must match in
order for the DVD to play. If the codes do not
match, the DVD will not play. The HR7012M
code is set to region 1. Playback of any other
region will not work in the HR7012M.
• If disc is not clean, use a commercially
available cleaning cloth to gently wipe
the disc from the center out. (Figure 4)
Note: Do not use solvents such as benzene,
thinner, cleaners, or antistatic spray
intended for analog discs.
Type of Discs the HR7012M Will Play
• DVD-Video: DVD containing video.
• CD-DA: CD containing musical or sound
content only.
• CD-Video: CD contains movie only.
• CD-R/RW: A disc that containing audio files
(for example, a CD-R with downloaded
MP3 files), MPEG, or JPEG files.
Note: The following discs will NOT play in the
HR7012M, Optical disc- CD-1, CD-ROM, and
DVD-ROM Mini disc- CDG (audio only, not
graphics), Blu-ray.
Loading and Playing Discs
Before loading a disc, make sure that it is
compatible with the player.
Press the POWER button to turn the system
ON. Load the disc (label facing the user) into
the disc slot. The disc will load automatically
and begin to play.
Note: Some discs may start at the root menu,
where play must be selected to start movie.
Notes on Discs
• Do not touch the disc surface. Handle the
disc by the edge.
• It is important that discs are clean prior to
use.
6
Figure 4
• Keep discs protected in their cases or
disc magazines when not in use. Do not
subject discs to heat/high temperature. Avoid leaving discs in a parked vehicle or
on a dashboard/rear tray.
• Do not use discs that have after-market
Paper or plastic labels/stickers attached. The following malfunctions may result
from using such discs:
• Inability to eject a disc (due to a label
or sticker peeling off and jamming the
eject mechanism).
• Inability to read audio data correctly
(i.e., playback skipping, or no playback)
due to heat shrinking of a sticker or
label causing a disc to warp.
• Use only standard, round discs. If you
insert irregular, non-round, shaped discs
they may jam in the DVD player or not play
properly.
HR7012 Rear Seat Video Headrest System Owner’s Manual
Front Panel Controls
HR7012M
1
2
16
3
15
13
4
5
6
7
14
S
13
12
8
9
VEDIO
AUDIO
L
AUDIO
R
11
10
Figure 5
1. DVD disc insertion slot
(Figures 5 and 6).
2. IR
Transmitter and IR Sensor
IR Transmitter: is used to broadcast audio
signal to the wireless IR headphones.
IR Sensor: is used to receive signals from
the remote control (Figures 5 and 6).
3. P
lay Button (HR7012M)
This button is used to begin playback of
the disc or USB media inserted (Figure 5).
4. Eject
Button
This button is used to eject the disc
(Figure 6).
5. SOURCE Button (HR7012M)
This button is used to select the DVD/
USB, M1/M2, AV/AUX, MEDIA or GAME
(optional) (Figure 5).
6. Stop Button
This button is used to stop the playback
of the disc or USB media in use (Figure 5).
7. POWER Button
This button is used to turn the HR7012M/
HR7012S ON and OFF (Figures 5 and 6).
(press and hold for 5 seconds to turn
OFF)
8. AUX Jacks (RCA Type)
The Jacks are intended for temporary
connection of an additional AV source
such as a video game device, or other
audio/video devices. To play the external
device, connect to the AUX Jacks, press
the SOURCE button on the front panel of
the HR7012M or on the remote control
until “AUX” appears on the screen and
press PLAY on the connected source
(Figures 5 and 6).
9. USB Port
This port is used to connect a USB device
for playback of content. To view content,
select “DVD” as the video source and
insert the USB device. The USB device
will start automatically and take priority
over the DVD. To play DVD’s, disconnect
the USB device from the port (Figure 5).
10.Protective Cover
Used to protect and cover the Headset/
Earbud jack, AV Input jacks and USB
port when not in use (Figures 5 and 6).
7
HR7012 Rear Seat Video Headrest System Owner’s Manual
Front Panel Controls (continued)
HR7012S
2
16
17
19
13
13
18
S
19
P
13
13
7
8
VEDIO
AUDIO
L
AUDIO
R
Figure 6
11.1/8”Wired Headset/Earbud Output Jacks
These jacks are used to connect two
standard wired headphones/earbuds
(Figures 5 and 6).
12.MENU/SELECT Button
This button is used to display and select
options on the main Setup Menu when a
disc or USB media is not inserted. When a
disc or USB media is inserted, this button
is used to display and select available
Disc/Media option (Figures 5 and 6).
13.VOLUME Direction Buttons
These buttons are used to raise and lower
the volume. (Figures 6).
14.NEXT / RIGHT Button(HR7012M)
This button is used to skip to the next
chapter or track during playback of a disc
(Figure 5).
15.PREVIOUS / LEFT Button (HR7012M)
This button is used to skip to the previous chapter or track during playback of a disc
(Figure 5).
16.7-inch TFT LCD Display Screen
(800 x 480) (Figure 5 and 6).
8
12
11
10
17.PIX Button(HR7012S)
This button is used to control levels of
Brightness, Contrast, Color, Tint and to
Reset all picture adjustment levels to
original factory settings (Figure 6)
18.SOURCE Button (HR7012S)
This button is used to select the M1/
M2, AV/AUX, MEDIA or GAME (optional)
(Figure 6).
19.Left/Right Buttons (HR7012S)
These buttons are used to navigate
menu selections on the screen
(Figures 6).
Warnings
• Do not use any solvents or abrasive
cleaning materials when cleaning the
screen. Use only a lightly dampened lint
free cloth to wipe the screen if it is dirty.
• Lock the front panel in the fully closed
position when not in use. Do not put
pressure on the screen, caution children to
avoid touching or scratching the screen..
HR7012 Rear Seat Video Headrest System Owner’s Manual
Remote Control and Headphone Battery Installation
Installation of the Remote Control Battery
The remote control comes with a battery already installed with a Pull Tab to prevent battery
discharge. Remove the Pull Tab before attempting to use the remote. (Figure 7).
Note: The remote control will only operate this device. It is not a universal remote control and
will not control other equipment.
Remote control
Back View
Figure 7
Protective Pull Tab (Clear Plastic )
1. W
hile holding the remote control, insert thumbnail into the battery door side notch (1) and
index fingernail into battery door upper notch (2) and slide battery holder open (Figure 8).
2. Install one CR2025 battery (1) (Figure 9).
Note: Make sure that the proper polarity (+ or -) is observed.
3. Slide the battery holder back into the remote control until it locks (Figure 10).
CR2025
3V
(1)
(2)
Figure 8
(1)
Figure 9
9
HR7012 Rear Seat Video Headrest System Owner’s Manual
Headphone Battery Installation
Installation of the Headphone Batteries
The wireless IR headphone unit requires two AAA batteries. 1.
Locate the battery compartment cover on the left earphone. 2.
While holding the left earphone in one hand, press down on the battery compartment
cover and slide it UP and OFF in the direction shown. (Figure 10)
3.
Insert two AAA batteries (included), carefully following the markings inside to ensure the
batteries are inserted properly ( “+”and “-” ends in the correct positions.)
4.
Replace the battery compartment cover. (Figure 10)
Figure 10
10
HR7012 Rear Seat Video Headrest System Owner’s Manual
Battery Cautions and Warnings
Cautions and Warnings
• Always keep the monitors, remote control
and headphones clean and dry.
• Always seek qualified personnel to
perform repairs to the system or individual
components of the system. Never attempt
your own repairs.
• Do not drop remote control and
headphones or expose to strong impacts.
• Do not expose monitors, remote control
and headphones to direct sunlight for
extended periods of time. • Always ensure that the battery is
correctly installed in the remote control
and headphones with the positive and
negative sides in the direction as shown in
the battery compartment.
• Use one CR2025(3V) Lithium battery
(160MAh) in the remote control. Do not use different types.
• Use two AAA(1.5v) Alkaline batteries
in
each
of
the
headphones.
Do not use different types.
• Do not use old batteries in the remote
control or headphones.
• When the battery fails to function, replace
it immediately.
• Remove the battery if the remote control
and headphones are not used for a month
or longer. • Keep all batteries out of the reach of
children. Should the battery be swallowed,
immediately consult a doctor.
• When disposing used batteries, please
comply with governmental regulations
or environmental rules that apply in your
area.
11
HR7012 Rear Seat Video Headrest System Owner’s Manual
Remote Control Operation
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(17)
(15)
(16)
Figure 11
12
HR7012 Rear Seat Video Headrest System Owner’s Manual
Remote Control Operation (continued)
1. ( M1) Monitor Select
Press this button to select and control HR7012M (M1) Monitor. (Figure 11)
9. U
P/DOWN/LEFT/RIGHT Arrows
Press these buttons to navigate the
menu selection on the screen. (Figure 11)
2. P
OWER
Press this button to turn the system ON. Press the button again to turn the system
OFF. (Figure 11)
10.DISPLAY
Press this button to display current disc
information while the disc is playing. Press UP/DOWN arrow buttons to select
the Title or Chapter. For Title/Chapter
selection, use the numeric buttons to
enter the desired Title/Chapter selection. (Figure 11)
3. TV (not applicable)
Note: If this button is pressed the remote
control will not control DVD functions
until the DVD button is pressed again. (Figure 11)
4. S
OURCE
Press this button to change the AV source
between DVD/USB and a connected AUX
source. (Figure 11)
5. P
IX
This button is used to make picture
adjustments. Each time the button
is pressed, the adjustment OSD
cycles through bars for BRIGHTNESS,
CONTRAST, COLOR, TINT, and RESET. Once the desired adjustment bar is
displayed, use the UP/DOWN button
to adjust the setting. The bar display
will automatically disappear if no
adjustments are made within 6 seconds
or if any button is pressed. (Figure 11)
6. DVD Source
This button is used to switch connected sources (DVD and USB). This button
is only active when remote control is
in the DVD mode and a USB device is
connected. (Figure 11)
7. S
YSTEM MENU
This button is used to make system setup
adjustments. Each time the button is
pressed, the adjustment OSD cycles
through bars for VOLUME CONTROL,
PICTURE CONTROL, FM MODULATOR,
OSD LANGUAGE, IRT ON/OFF, and
DEFAULT DVD ON/OFF (MI) or DEFAULT
AV AUTO ON/OFF (M2). (Figure 11)
8. ENTER
Press this button to make an OSD
selection
or
begins
playback
of the DVD/USB. (Figure 11) 11.PLAY Button
Press this button to initiate play mode
when a disc is loaded in the disc
compartment. (Figure 11)
12.SCAN BACKWARD Button
Press this button to search in the
backward direction. Press repeatedly to
change the search speed from 2, 4, 8, and
16 times the normal speed. (Figure 11)
13.PAUSE Button Press this button to pause the playback of
a disc. Pressing pause again or pressing
the Play button will resume normal
playback. (Figure 11)
14.PREV Button
When a disc has more than one Chapter,
Track, or File, you can move to another
Chapter/Track/File. Press this button
briefly during play to step back to the
previous Chapter for DVD-video or
Track/File for VCD, SVCD, MP3, CD, etc.
(Figure 11)
15.FMM ON/OFF
This button is used to turn the wireless
FM Modulator ON and OFF. (Figure 11)
16.IRT ON/OFF
This button is used to turn the Infrared
Transmitter ON and OFF for Wireless
IR Headphones. Pressing M1 then the
IRT ON/OFF button will control the IR
Transmitter for M1. Pressing M2 then
the IRT ON/OFF button will control the IR
Transmitter for M2. (Figure 11)
17.Numbers
Decimal number: 0 to 9; and +100: Add
100. Used for selecting tracks on a disc. (Figure 11) 13
HR7012 Rear Seat Video Headrest System Owner’s Manual
Remote Control Operation (continued)
(31)
(30)
(29)
(28)
(27)
(26)
(25)
(24)
(23)
(22)
(21)
(20)
(19)
(18)
Figure 12
14
HR7012 Rear Seat Video Headrest System Owner’s Manual
Remote Control Operation (continued)
18.STOP
Press
this
button
to
playback of disc. (Figure 12)
stop
19.NEXT Button
When a disc has more than one
Chapter, Track, or File, you can move
to another Chapter/Track/File. Press
the button briefly during play to select
the next Chapter for DVD-video or
Track/File for VCD, SVCD, MP3, CD, etc. (Figure 12)
24.REPEAT
Press this button to switch the repeat
mode by CHAPTER, TITLE, ALL and
cancel while playing DVD-video. Other
disc types such as VCD, CD, and SVCD
that only have two repeat modes
that can be selected: TRACK and ALL
Note: Both repeat functions of VCD
and SVCD need the PBC status set
to ON when available. (Figure 12)
25.ZOOM
Press this button to enlarge the
picture in the movie by 2x, 3x, and
4x, or shrink the picture in the movie
by 1/2, 1/3, and 1/4. (Figure 12)
20.AUDIO
Press this button to display and
select the available AUDIO languages
in DVD mode. Each time you press
the button, the language changes.
Note: The audio languages vary
from disc to disc. (Figure 12)
26.DISC MENU
Press this button to access the
menu of the DVD in play. (Figure 12)
21.SCAN FORWARD Button
Press this button to search in the
forward direction. Press repeatedly
to change the search speed from 2,
4, 8, and 16 times the normal speed.
(Figure 12)
27.VOLUME DOWN (-) or UP (+)
Press this button to increase or
decrease the volume for the wired
headphones or select the level of the
picture adjustments when the unit is in
picture adjustment mode. (Figure 12)
22.SUBTITLE
Press this button. If the current disc
has different subtitle options, this
now appears on the screen. Press
this button repeatedly until you
have reached your desired subtitle
option. (Figure 12) NOTE: The Subtitle
selections vary from disc to disc
28.MUTE
Press this button to mute the sound
transmitted to the headphones. “MUTE”
will be displayed on the screen. Pressing
the button again restores sound to
the previously set level. (Figure 12)
23.SETUP (Unit must be set DVD source)
Press this button to navigate the Setup
Menu. Please refer to the following pages
to configure the system: General Setup
Page, Audio Setup Page, Preference Page,
and Password Setup Page. (Figure 12)
29.DVD Mode Select
Press
this
button
to
DVD functions. (Figure 12)
control
30.EJECT
Press this button to eject the disc from the
disc slot. (Figure 12) (HR7012M only)
31.(M2) Monitor Select
Press this button to select and control HR7012 (M2) Monitor. (Figure 12)
15
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Menu
The System Menu allows the user to personalize the HR7012 settings. It is used in the initial setup
to adjust the picture quality and customize an adjustable functions. Once the initial settings
are customized, they will remain the same until modified or reset to the factory default settings.
NOTE: System Menu changes are best made without a DVD inserted into the unit.
This section describes how to adjust and set settings using the six setup screens (Figure 13):
1.
2.
3.
Volume Control
Picture Control
FM Modulator (M1 Only)
4.
5.
6.
HR7012M (M1)
OSD Language
IRT ON/OFF
Default DVD ON/OFF (HR7012M)
DEFAULT AUTO ON/OFF (HR7012S)
HR7012S (M2)
Using the System Menu
Figure 13
Navigating and selecting available settings in the System Menu is accomplished using the
Remote Control buttons (Figure 14), or the Front Panel buttons (Figure 15).
Follow the steps outlined in this section to select and customize each of the six adjustable
functions (Sub-Menus) listed above, and refer to the sections that apply.
SYSTEM
MENU
UP,DOWN,
LEFT and
RIGHT
DIRECTION
BUTTONS
ENTER
BUTTON
Figure 14
HR7012M
MENU
SELECT
HR7012S
MENU
SELECT
Figure 15
NOTE: Press and Hold the Menu/Select button for 5 seconds to access the System Menu.
16
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup MENU (continued)
System Sub-Menus
1. P
ress the System Menu button on the remote control (Figure 14) or Press and
hold the Menu/Select button on the front panel of the system for 3 to 5 seconds
(Figure 15) to show the System Menu.
2. U
se the UP/DOWN direction buttons to select the desired setting in the System Menu
screen and press the Enter button or Menu/Select button to select the Sub-Menu
screen. NOTE: Selected Items in the System Menu and the Sub-Menus will be highlighted
in green.
3. U
se the UP, DOWN, LEFT and RIGHT direction buttons to select an item in the Sub-Menu
screen and then press the Enter button to select.
4. To exit System Menu screen or the Sub-Menu screens at anytime, press the System
Menu button on the remote control or the Menu/Select button on the front panel.
NOTE: The System Menu and all Sub-Menus will automatic disappear from main screen
within 5 or 6 seconds if no selections have been made.
17
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup Sub-Menus
Volume Control (Wired Headphones Only)
(HR7012M)
(HR7012S)
Figure 16
VOLUME CONTROL from the Front Panel (M1 and M2) (Figure 16):
1.
ress and hold the Menu/Select button on the front panel of the system (Figure 15) for
P
3 to 5 seconds to show the System Menu. (Figure 13)
2.
Use the UP/DOWN direction buttons to select Volume Control and press the
Menu/Select button to enter the sub-menu (Figure 16).
3.
Using the LEFT / RIGHT direction buttons, adjust the volume level from “0” to “32” as desired.
NOTE: Default control volume level set at level 10.
4.
After volume level selection is made, the Volume Control sub-menu will automatically
disappear from main screen within 5 or 6 seconds, or press the Menu/Select button
again to return to the System Menu.
VOLUME
Figure 17
VOLUME CONTROL from the Remote Control (Figure 17):
1.
Select M1 or M2 on the Remote Control.
2.
Using the using the Volume +/- direction buttons adjust the volume level from “0” to “32”
as desired. NOTE: Default control volume level set at level 10.
3.
After volume level selection is made, the volume
will automatically disappear from main screen within 5 or 6 seconds.
18
control
bar
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup Sub-Menus (continued)
Note: Picture control settings for DVD
mode are separate from the other A/V
sources. After adjusting the DVD picture controls, the user can make separate
settings for the other A/V sources.
Picture Control
(HR7012M)
(HR7012S)
Figure 18
PICTURE CONTROL from the Front Panel (M1 and M2) (Figure 18):
1. P
ress and hold the Menu/Select button on the front panel of the system (Figure 15) for
3 to 5 seconds to show the System Menu. (Figure 13)
2. U
se the UP/DOWN direction buttons to select Picture Control and press the
Menu/Select button to enter the sub-menu.
3. U
se the UP or DOWN direction buttons to select one of the four setting
in the Sub-Menu (Brightness, Contrast, Color,Tint and Reset). Using the
LEFT/RIGHT direction buttons, adjust the level of the picture setting chosen.
NOTE: Levels are set from “0” to “16” for Brightness, Contrast and Color. The levels for Tint
is set from “-16” to “+16” . No Tint Control in PAL Mode.
4. A
fter level setting(s) are made, the Picture Control sub-menu will automatically disappear from main screen within 5 or 6 seconds, or press the Menu/Select button again to return
to the System Menu.
PICTURE CONTROL from the Remote Control:
1.
Select “M1” or “M2” and press the PIX button to select Picture Control.
2.
se the UP/DOWN direction buttons to select one of the four setting
U
in the Sub-Menu (Brightness, Contrast, Color, Tint and Reset). Using the
LEFT/RIGHT direction buttons, adjust the level of the picture setting chosen.
NOTE: Levels are set from “0” to “16” for Brightness, Contrast and Color. The levels for Tint
is set from “-16” to “+16”. No Tint Control in PAL Mode.
3.
fter level setting(s) are made, the Picture Control sub-menu will automatically disappear A
from main screen within 5 or 6 seconds, or press the PIX button again.
4.
Select reset to return the picture setting control back to factory defaults.
19
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup Sub-Menus (continued)
fm modulator
(HR7012M)
Figure 19
FM MODULATOR ON/OFF from the Front Panel (Figure 19):
1.
Press and hold the Menu/Select button on the front panel of the system for 3 to 5
seconds to show the System Menu. (Figure 13)
2.
Use the UP/DOWN direction buttons to select FM Modulator and press the
MENU/SELECT button to enter the sub-menu.
3.
se the UP/DOWN direction buttons to select FM Modulator ON/OFF and press
U
Menu/Select button to enter selection.
4.
se the UP/DOWN direction buttons to select FM Modulator ON or OFF and press the
U
Menu/Select button to enter selection. When ON is selected, the FM Modulator screen
will display the channel/frequency the system is set to. When OFF is selected, the FM
Modulator screen will display FMM OFF.
5.
The FM Modulator sub-menu will automatically disappear from main screen within 5
or 6 seconds, or use the UP/DOWN direction buttons to select BACK to return to the System Menu.
NOTE: See page 22 for FM channel selection.
20
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup Sub-Menus (continued)
FM Channel
HR7012M (M1 only)
HR7012S (M1 only)
SYSTEM
MENU
SYSTEM MENU
VOLUME
VOLUMECONTROL
CONTROL
PICTURE
PICTURE CONTROL
CONTROL
FM MODULATOR
FM
MODULATOR
LANGUAGE
OSD
OSD LANGUAGE
IRT ON/OFF
ON/OFF
IRT
DEFAULTAUTO
ON/OFF
DEFAULT
DVD ON/OFF
EXIT
Figure 20
FM CHANNEL from the Front Panel (M1 Only) (Figure 20):
1.
Press
and hold the Menu/Select button on the front panel of the system (Figure 15) for
3 to 5 seconds to show the System Menu. 2.
se the UP/DOWN direction buttons to select FM Modulator and press the
U
Menu/Select button to enter the sub-menu.
3.
se the UP/DOWN direction buttons to select FM Channel and press Menu/Select
U
button to enter selection. 4.
Use the UP/DOWN/LEFT and RIGHT direction buttons to select the best channel/
frequency from a four page list of one hundred possibilities then press the Menu/
Select button to enter selection. 5.
When a channel/frequency is selected, the FM Modulator screen will display the channel/
frequency the system is set to. 6.
The FM Modulator sub-menu will automatically disappear from main screen within 5 or 6
seconds, or use the UP/DOWN direction buttons to return to the System Menu.
21
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup Sub-Menus (continued)
FM Channel From the Remote Control (Figure 21):
1.
Select “M1” on the Remote Control.
2.
Press the System Menu button then use the UP/DOWN direction buttons to select
FM Modulator and press the Enter button to enter the FM Modulator sub-menu.
3.
se the UP/DOWN/LEFT and RIGHT direction buttons to select the best channel/
U
frequency from a four page list of one hundred possibilities then press the Menu/
Select button to enter selection. NOTE: When a channel/frequency is selected, the FM
Modulator screen will display the channel/frequency the system is set to.
4.
The FM Modulator sub-menu will automatically disappear from main screen within 5 or 6
seconds, or use the UP/DOWN direction buttons to select “BACK” to return to the System
Menu.
FM Modulator ON/OFF Direct Access Button on the Remote Control (Figure 21):
1.
Press the FMM ON/OFF button on the remote control to turn the FM Modulator ON and
OFF. When ON is selected, the channel/frequency (FMM xxxxMHz) the system is set to will
be displayed on the lower left-side of the main screen. When OFF is selected, FMM OFF
will be displayed on the lower left-side of the main screen. The displayed selection will
automatically disappear from main screen within 5 or 6 seconds. (Figure 21)
FMM ON/OFF
BUTTON
Figure 21
22
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup Sub-Menus (continued)
OSD LANGUAGE
HR7012M (M1)
HR7012S (M2)
Figure 22
OSD LANGUAGE from the Front Panel (M1 and M2) (Figure 22):
1.
Press
and hold the Menu/Select button on the front panel of the system (Figure 15) for
to 5 seconds to show the System Menu.
2.
se the UP/DOWN direction buttons to select OSD Language and press the Menu/
U
Select button to enter the sub-menu.
3.
Use the UP/DOWN direction buttons to select the desired language then press the
Menu/Select button to save the setting. OSD LANGUAGE from the Remote Control
4.
Select “M1” or “M2” on the Remote Control.
5.
Press the System Menu button then use the UP/DOWN direction buttons (figure 11) to
select OSD Language and press the Enter button to enter the OSD Language sub-menu.
6.
Use the UP/DOWN direction buttons to select the desired language then press the
ENTER button to save the setting.
23
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup Sub-Menus (continued)
IRT ON/OFF
HR7012M (M1)
HR7012S (M2)
Figure 23
IRIRT ON/OFF (M1 and M2) from the Front Panel(Figure 23):
1.
Press
and hold the Menu/Select button on the front panel (Figure 15) of the system for
3 to 5 seconds to show the System Menu. 2.
Use the UP/DOWN direction buttons to select IRT ON/OFF and press the Menu/Select button to enter the sub-menu. 3.
se the UP/DOWN direction buttons to select IRT ON or OFF and press the
U
Menu/Select button to enter selection. When ON is selected, IRT ON will be displayed on
the System Menu screen. When OFF is selected, IRT OFF will be displayed on the System
Menu screen.
IRT ON/OFF (M1 and M2) from the Remote Control
4.
Select “M1” or “M2” on the Remote Control.
5.
Press the System Menu button then use the UP/DOWN direction buttons (Figure 14) to
select IRT ON/OFF and press the Enter button to enter the sub-menu.
6.
se the UP/DOWN direction buttons to turn the IRT ON or OFF and press the
U
ENTER button to enter selection. When ON is selected, IRT will be displayed on the
System Menu screen. When OFF is selected, IRT OFF will be displayed on the System
Menu screen.
IRT ON/OFF Direct Access Button on the Remote Control
7.
Select M1 or M2 on the Remote Control.
8.
Press the IRT ON/OFF button to turn the IRT ON or OFF. When ON is selected, IRT ON will
be displayed on the System Menu screen. When OFF is selected, IRT OFF will be displayed
on the System Menu screen and will disappear from screen within 5sec - 6sec.
24
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup Sub-Menus (continued)
DEFAULT DVD ON/OFF (Model DD7012)
HR7012M (M1)
HR7012M (M2)
Figure 24
With the “Default DVD ON” feature selected, the unit will default to DVD Mode each time the
system is turned ON. For example, if the user is playing a game and the system is turned OFF,
the next time the system is turned ON, it will power-up in DVD Mode. Default DVD ON/OFF from the Front Panel (Figure 24):
1.
Press
and hold the Menu/Select button on the front panel (Figure 15) of the system for
3 to 5 seconds to show the System Menu
2.
se the UP/DOWN direction buttons to select DEFAULT DVD ON/OFF and press the
U
Menu/Select button to enter the sub-menu. 3.
se the UP/DOWN direction buttons to select DEFAULT DVD ON or OFF and press the
U
Menu/Select button to enter selection.
Default DVD ON/OFF from the Remote Control
1. Select “M1” or “M2” on the Remote Control.
2.
Press the System Menu button then use the UP/DOWN direction buttons (Figure 11) to
select DEFAULT DVD ON/OFF and press the Enter button to enter the sub-menu.
3.
Use the UP/DOWN direction buttons to select DEFAULT DVD ON or OFF and press the enter button to make the selection. 25
HR7012 Rear Seat Video Headrest System Owner’s Manual
System Setup Sub-menus (continued)
DEFAULT AUTO ON/OFF (Model MM7012)
HR7012S (M1)
SYSTEM
MENU
SYSTEM MENU
VOLUME
VOLUMECONTROL
CONTROL
PICTURE
PICTURE CONTROL
CONTROL
FM MODULATOR
FM
MODULATOR
LANGUAGE
OSD
OSD LANGUAGE
IRT ON/OFF
ON/OFF
IRT
DEFAULTAUTO
ON/OFF
DEFAULT
DVD ON/OFF
EXIT
HR7012S (M2)
SYSTEM
MENU
SYSTEM MENU
VOLUME
VOLUMECONTROL
CONTROL
PICTURE
PICTURE CONTROL
CONTROL
FM MODULATOR
FM
MODULATOR
LANGUAGE
OSD
OSD LANGUAGE
IRT ON/OFF
ON/OFF
IRT
DEFAULTAUTO
ON/OFF
DEFAULT
DVD ON/OFF
EXIT
Figure 25
Default AUTO ON/OFF from the Front Panel (Figure 25):
1. Press
and hold the Menu/Select button on the front panel (Figure 15) of the system for
3 to 5 seconds to show the System Menu. 2. U
se the UP/DOWN direction buttons to select DEFAULT AUTO ON/OFF and press the
Menu/Select button to enter the sub-menu. 3. U
se the UP/DOWN direction buttons to select Default Auto AV, M1 or OFF and press the
Menu/Select button to enter selection.
Note:
• Default Auto AV: HR7012S monitor(s) will automatically turn ON when a connected
video source is detected and turned ON. NOTE: This feature will only work if the
system is installed with an external source connected to the A/V IN of the unit.
• Default Auto M1: HR7012S (M2) monitor(s) will automatically turn ON when the
HR7012M (M1) is first turned ON.
• Default Auto OFF: HR7012S (M2) monitor(s) will not turn ON automatically when
HR7012M (M1) is turned ON or if a connected video source is detected and turned ON.
Default AV AUTO ON/OFF from the Remote Control
1. Select “M1” or “M2” on the Remote Control.
2. P
ress the System Menu button then use the UP/DOWN direction buttons (Figure 11) to
select DEFAULT AV AUTO ON/OFF and press the Enter button to enter the sub-menu.
3. Use
the UP/DOWN direction buttons to select DEFAULT AV AUTO ON/OFF and press the
ENTER button to enter the sub-menu. 26
HR7012 Rear Seat Video Headrest System Owner’s Manual
dvd playback SETTINGS AND ADJUSTMENTS
The DVD Playback Setup Menu contains features and options that allows the user to customize
the DVD player. For example, the user can set a language for the on-screen display or prevent
DVD playback for children.
Using the Setup Button on the remote control
1.
Press the SETUP button on the remote. The DVD Setup Menu appears on the screen with
four major setup option pages. (Figure 25)
Figure 26
2.
Use the UP/DOWN direction buttons to highlight the desired setup option page.
Figure 27
3.
Use the RIGHT direction button to enter the desired setup option page.
4.
Use the UP/DOWN direction buttons to select the desired options and press Enter to
confirm the selection.
5.
Repeat steps 3~4 to continue setting all available options in the setup option page.
6.
To select a different Setup Option Pages, press the LEFT direction button to return to the
Setup Menu.
7.
Repeat steps 2~5 for each of the Setup Option Pages. 8.
Press the SETUP button on the remote control again to exit Setup Menu and save changes.
27
HR7012 Rear Seat Video Headrest System Owner’s Manual
SETTINGS AND ADJUSTMENTS (continued)
LANGUAGE SETUP
Language (for On-Screen Display (OSD): The Language setup option page allows the user to
select the language for the OSD. The user can either select English, French, Spanish, German
or Italian for the OSD language. (Figure 28)
Figure 28
Subtitle: The Subtitle setup option page allows the user to select the language for
the OSD. The user can either select English, French, Spanish, German, Italian, Chinese,
Japanese, Thai or OFF to be displayed on the screen during playback of a disc.(Figure 26)
Note: The subtitle selection is only available for discs that are recorded in the above listed
languages. If the selected, language is not available, the player will play and display on the
screen the original language contained in the disc. (Figure 29)
Figure 29
Audio: The Audio setup option page allows the user can select the audio language (English,
French, Spanish, German, Italian, Chinese, Japanese or Thai). (Figure 30
Note: The audio selection is only available for discs that are recorded in the above listed
languages. If the selected, language is not available, the player will play and display on the
screen the original language contained in the disc.
Figure 30
28
HR7012 Rear Seat Video Headrest System Owner’s Manual
dvd playback SETTINGS AND ADJUSTMENTS (continued)
VIDEO SETUP
TV Display: The TV Display setup option page allows the user to adjust screen aspect ratio to
either 4:3 or 16:9. (Figure 31)
4:3) D
isplays a wide picture with black bands on the upper and lower portions of the
screen.
16:9) Displays a wide picture with black bands on the upper and lower portion of the
screen. The bandwidth will vary, depending on the aspect ratio of the disc.
Figure 31
TV Type: The TV TYPE setup allows the user to match the video output of the player to the
broadcast system of a connected TV. This system supports both National Television System
Committee (NTSC) and Phase Alternating Line (PAL) television broadcasting standards. (Figure 32)
NTSC)Select this mode if the connected TV is a NTSC system. The video signal of a PAL disc
will be converted to NTSC format
PAL) S elect this mode if the connected TV is a PAL system. The video signal of a NTSC disc
will be converted to PAL format
Multi)Select this mode if the connected TV is a multi-system. The video signal format of a
will be in accordance with the video signal of the disc
NOTE: For best performance, this setting should remain at NTSC.
Figure 32
29
HR7012 Rear Seat Video Headrest System Owner’s Manual
SETTINGS AND ADJUSTMENTS (continued)
RATING SETUP
Rating: The Rating setup option page allows the user to limit the content of movie playback
(G, PG, PG–13, R, NC– 7 and Adult). The lower the value, the more strict the control. The rating
level can only be changed using a parental control password. For first time use the default
parental control password is 3308 using UP directional button to enter parental mode, key in
the default password (3308) and press ENTER. Press ENTER again to select the parental level,
select the level and press ENTER (Figure 33). To change the password to your own password
press “Change Password” mode and enter the default password (3308) and press ENTER. Press
ENTER and again and key in a new four digit password. After complete press ENTER to end the
process. (Figure 34)
Note: The Default Password is 3308. This password is always effective even after you have
selected your own password and changed it. To avoid the possibility of others using the
default password to set the parental level and change the password, you can record this
default password in another area and delete it from this manual. Some discs can be limited
depending on the age of users while some discs cannot.
Figure 33
Figure 34
30
HR7012 Rear Seat Video Headrest System Owner’s Manual
SETTINGS AND ADJUSTMENTS (continued)
Misc SETUP
Misc Setup: Select “MISC” using the UP/DOWN direction buttons, then press the RIGHT
direction button to enter the Misc menu. Select the subtitle you desire using the UP/DOWN
direction buttons, then press “ENTER” to confirm the setting. Press the LEFT direction button
to return. (Figure 35)
Figure 35
Load Factory: Load Factory allows you to reset all options to factory settings. * This function
will not affect the Rating control settings. (Figure 36)
Screen Saver
Figure 36
ON -Screen saver will appear
OFF -Screen saver will not appear
Note: The DVD player will enable the Screen Saver mode if the unit is inactive for approximately
2 minutes. (Figure 37)
Figure 37
31
HR7012 Rear Seat Video Headrest System Owner’s Manual
DISC BASICS
To get the optimum use out of the DVD player, make sure you read this section completely.
Types of Discs your DVD Player will play
•
DVD* disc - DVD discs that contain video.
•
Audio disc - Audio CDs that contain musical or sound content only.
•
MP3 disc - A disc that contains audio files (for example, a CD-R with
downloaded MP3 files).
*This system is capable of playing most recordable DVD formats. However, due to
the variety of disc manufacturers and software, playback cannot be guaranteed.
Loading and Playing Discs
Before you load a disc, make sure that it is compatible with the player. Insert the disc with the
disc label facing toward the driver.
Note: The following Discs CANNOT be used with this player:
•
Mini-Disc
•
Laserdisc
•
CD-1, CD-ROM, DVD-ROM, Super Audio CD (SACD), DVD Audio, JPEG,
BD (Blu-ray Disc). To load and Play a Disc
1.
Press the Power button to turn the unit ON.
2.
Select DVD mode and insert the disc (label facing user) into the disc compartment.
3.
Push down gently on the disc and the player will pull the disc in.
Audio / Video Inputs and Outputs
Audio Output
The Audio output will provide the Audio signal from the M1 unit. This output can be heard on
the Built-In Wireless Modulator.
32
HR7012 Rear Seat Video Headrest System Owner’s Manual
PLAYBACK OF MEDIA
Playing DVD’s
1.
Press the DISPLAY button on the remote control to display the status banner. The
banner include Title, Chapter, Angle, Audio, Subtitle, Audio, Subtitle, Title selection & Chapter
selection.
2.
Title Selection
Press the Number (0~9) buttons to initiate a change of title selection, then press ENTER
to implement the selection.
3.
Chapter selection
Press the Number (0~9) buttons to initiate a change of chapter selection, then press
ENTER to implement the selection. As you toggle through the options, the repeat option
changes at that time. The track, for example, repeats once that track has ended. The
selected repeat option loops repeatedly until you turn it off.
Playing USB’s
1.
The System will detect the insertion of the USB media automatically if no disc is loaded. The system only auto detects the first media inserted (USB drive); the second media
source can be manually selected by pressing the DVD Source button on the remote
control.
2.
When a disc is inserted, the system will switch to DVD mode immediately regardless if
USB media is currently playing.
3.
The DVD source (DVD or USB) can only be changed while the DVD is not playing.
4.
This system cannot support more than 2 memory partitions on the USB thumb drive.
Note: The system will always default to the DVD when the system detects a disc in the
DVD player.
Playing MP3 Disc’s
CD-R discs that have been encoded in MP3 format can be played on your DVD player. The DVD
player plays the songs in the order they were burned on to the disc. When playback is started
the elapsed time of the track that is playing will be displayed.
Selecting Folders and Songs
When a device containing MP3 files is loaded in the player, the navigation menu appears
automatically.
1.
Use the UP/DOWN direction buttons to move the highlight to the desired folder
(if present) on the left side of the menu and press ENTER. The songs in the folder will be
displayed on screen. 2.
Use the UP/DOWN direction buttons to highlight the desired track containing the song
and Press ENTER to begin track playback.
33
HR7012 Rear Seat Video Headrest System Owner’s Manual
PLAYBACK OF MEDIA (continued)
Skipping Songs
Use the Next button on the remote control to move to the next song. Use the Previous button
to move to the previous song.
Selecting a Play Mode
Filter (For MP3 & JPEG only)
Filter Mode enables or disables the display of files contained on the media based on their file
extension. (Figure 38)
The filter function applies to the following formats:
Audio - Audio data format (MP3, WMA)
Photo - Photo data format (JPEG)
Video - Video data format (MPEG , )
Figure 38
Flat Mode: play the entire disc
This mode is always on (default). During the Flat Mode, all the data folder with MP3, JPEG &
Movies will be played in sequence. If the Flat Mode function is off, it will only play the selected
folder; other folders are disabled. (Figure 39)
Figure 39
34
HR7012 Rear Seat Video Headrest System Owner’s Manual
PLAYBACK OF MEDIA (continued)
Repeat: Play Repetitively
Repeat function has 4 options : Off, Single, Folder and All. Move cursor to Repeat Function and
press Enter, each time Enter is pressed the unit will cycle through the available options
(Off/Single/Folder and All are displayed in that order). Repeat default is Off; (Figure 40)
Off
Turn off repeat function
Single
Repeat the song being played until STOP is pressed.
Folder
Play all songs in a folder repetitively
All
Play all songs on the disc repetitively
Figure 40
Mode: Play Mode
The Mode function has 4 options: Normal, Shuffle, Random and Music Intro. Move cursor
to the Mode function area and press Enter repeatedly till the desired mode is displayed.
Normal/Shuffle/Random/Music Intro are displayed in that order. The Mode function default
is Normal. (Figure 41)
Normal: Play all songs in folder once.
Shuffle: Play songs in a folder in a shuffle order. Each song in the folder is played only once.
Random:Play songs in a folder in a random order. Each song in a folder will only be played
once.
Music Intro: Play each song in order in the folder for 10 seconds The purpose of the “Music
Intro” function is to provide the user with a sample of each song for 10 seconds, thereby
making it easy to select and listen to a favorite song.
Figure 41
35
HR7012 Rear Seat Video Headrest System Owner’s Manual
PLAYBACK OF MEDIA (continued)
Add to program
Method: To add the selected songs into Browser view, make sure disc playback is off. Move
cursor to “Edit Mode” function and press ENTER. After “Edit Mode” is selected, move cursor to
songs list and select the songs which will be compiled and press ENTER. A check mark appears
to the left of the selected song; to add the selected songs to the program, move cursor to the
“Add to Program” function and press ENTER. The selected songs is added into a new program
list and the check mark will disappear on play list, move cursor to “Program View” function
and press ENTER to browse the songs in the program. Press Play button to play the selected
songs. (Figure 42)
Note: Edit Mode, Program View or Add to Program functions are relationship related when
selecting the preferred song add to the songs list.
Figure 42
Clear program
Method: To clear the selected song files, press the STOP button twice during playback mode. Move the cursor to the “Edit Mode” function and press ENTER. After “Edit Mode” is selected,
move cursor to selected songs list and select the songs you want to delete. Press ENTER and a
check mark will appear to the left of the selected song. Move the cursor to clear program and
press ENTER, the selected songs will be deleted from the play list. (Figure 43)
Figure 43
36
HR7012 Rear Seat Video Headrest System Owner’s Manual
DVD Region Codes
The DVD player is preset to a region code at the factory depending on where the DVD player
is sold. DVDs from a different region cannot be played in this unit and the unit will display
“WRONG REGION”. (Figure 44)
24
Figure 44
Region 1- USA, Canada
Region 2- Japan, Europe, South Africa, Middle East, Greenland
Region 3- S. Korea, Taiwan, Hong Kong, Parts of South East Asia
Region 4- Australia, New Zealand, Latin America (including Mexico)
Region 5- Eastern Europe, Russia, India, Africa
Region 6- China
37
HR7012 Rear Seat Video Headrest System Owner’s Manual
GAME CONTROLLER OPERATION
Battery Installation (Figure 45)
Bottom Side of Game Controller
Before attempting to operate your game
controller, install the batteries as described
below:
Battery Case
1. Turn the game controller face down. Using a finger, slide battery cover off in
the direction of the arrow.
1.5V AAA
1.5V AAA
2. Install three “AAA” batteries. Make
sure that the proper polarity (+ or -) is
observed.
3. Align the cover tabs with the game
controller and slide the cover until it locks.
Figure 45
Functional Description (Figure 46)
SELECT
S
START
SELECT
S
TA
TA
DIRECTION
KEYS
TB
SELECT
A
A
START
S
TB
B
P1
TA
A
TB
B
START
P2
B
LCD-POWER
INDICATOR
P1 GAME CONTROLLER
P2 GAME CONTROLLER
Figure 46
1. Use the START button to enter the games list (1-54). Then use the direction buttons to
move the arrow to the desired game. Press START to select the game. Use select button to
exit the game list. 2. A Key : “A Function Key” activates the jump and optional weapons.
3. B Key : “ B Function Key” activates Bullet fire and attack.
4. TA Key : TURBO “A” Function Key.
5. TB Key : TURBO “B” Function Key.
6. S Key : No function.
7. Press START to begin the game. Press START again at any time to pause the game.
Two Player Games
The game source can be selected from either monitor. The optional game package
(HR7012GP) allows either or both users to play video games.
• Player 1 is on a first come, first served basis. • If the M2 user selects the game first they are automatically Player 1 and if the M1 user
wants to play against the M2 user they become Player 2.
• If the M1 user selects the game first they are automatically Player 1 and if the M2 user
wants to play against the M1 user they become Player 2.
38
HR7012 Rear Seat Video Headrest System Owner’s Manual
Troubleshooting
Symptom
Remedy
Device does not power “ON”
• Is the ignition turned “ON”?
• Is the screen rotated to the operating position?
• Are batteries installed in remote control?
IR sensor inoperative
• Verify that the batteries in the remote control are good.
• Verify that the remote sensor eye is not obstructed.
• Verify that M1 or M2 has been selected correctly.
Disc won’t play
• Insert a disc with label side facing toward user.
• Check if the disc is defective by trying another disc.
• Check the type of disc you put into DVD compartment slot. This DVD player only plays DVDs, audio CDs, and MP3s. It
will not play a Blu-ray disc.
• Both the device and the disc are coded by region. If the
regional codes don’t match, the disc can’t be played. Disc plays, but then stops
immediately
• The disc is dirty and needs cleaning.
• Condensation has formed. Allow the player to dry out.
• The disc is scratched. Replace the disc.
No picture
• Check that you are in DVD mode if playing a DVD
Distorted picture
• Check the disc for fingerprints and clean with a soft cloth,
wiping from center to edge.
• Sometimes a small amount of picture distortion may
appear. This is not a malfunction.
Cannot advance through a
movie
• You cannot advance through the opening credits and
warning information that appears at the beginning of
movies because the disc is programmed to prohibit that
action.
No sound or distorted sound
• If you are using the IR headphones, make sure you turn ON
the IR transmitter on the DVD system.
• Verify that the batteries in the IR Headphones are good.
• Is volume turned “UP” on IR Headphones?
• Is anything blocking signal between the monitor and the
Headphones?
• Make sure your DVD player is connected properly. Make
sure all cables are securely inserted into the appropriate
jacks.
• The disc is loaded backwards. Turn the disc around so that
the disc is facing towards the driver.
Device feels warm
• When the device is in use for a long period of time, the
surface will be heated. This is normal.
Player does not respond
to all commands during
playback
• Operations are not permitted by the disc.
• Refer to the instructions in the disc inlay.
39
HR7012 Rear Seat Video Headrest System Owner’s Manual
Specifications
Monitor Specifications
Type
TFT Active Matrix LCD
Resolution
2400 (W) x 480 (H)
Pixels
1,152,000
Back Light
LED
Power Source
+12 VDC
Power Consumption
28W
Operating Temperature
32°F ~ 125°F (0°C ~ +55°C)
Storage Temperature
-22°F ~ 150°F (-20°C ~ +70°C)
Video Display System
NTSC/PAL
Back Light Life
20,000 hours
Headphone Audio Output
0.03W @ 32 ohm
40
HR7012 Rear Seat Video Headrest System Owner’s Manual
Compliance Information
FCC Notice
Notice
This device has been tested and found to
comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
device generates, uses, and can radiate radio
frequency energy, and if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this device
does cause unacceptable interference to
radio or television reception, which can be
determined by turning the device OFF and
ON, the user is encouraged to try to correct
the interference by one or more of the
following measures:
Disposal of Old Electrical & Electronic
Equipment (Applicable in the European
Union and other European countries with
separate collection systems)
• Increase the separation between the
device and receiver.
• Consult your dealer or an experienced
radio/TV technician for help.
This symbol on the product or on its
packaging indicates that device shall not
be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of electrical
and electronic equipment. By ensuring this
device is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this device. The recycling
of materials will help to conserve natural
resources. For more detailed information
about recycling of this device, please contact
your local city office, your household waste
disposal service or the shop where you
purchased the device. Applicable accessory:
remote control.
FCC Warning:
To assure continued FCC compliance, the
user must use the provided grounded power
supply cord and the shielded video interface
cable with bonded ferrite cores. Also, any
unauthorized change or modifications to
this device would void the user’s authority
to operate this device.
Macrovision Notice
This product incorporates copyright
protection technology that is protected
by U.S. patents and other intellectual
property rights. Use of this copyright
protection technology must be authorized
by Macrovision, and is intended for home
and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse engineering or disassembly is
prohibited.
41
HR7012 Rear Seat Video Headrest System Owner’s Manual
USER NOTES
42
HR7012 Rear Seat Video Headrest System Owner’s Manual
43
If you have any questions regarding this product or
require technical assistance, please call 1-800-225-6074
© 2012 AUDIOVOX,150 Marcus Blvd. Hauppauge, NY 11788
44
128-9046