- Home
- Domestic appliances
- Small kitchen appliances
- Barbecues & grills
- Charbroil
- 461334813
- Owner's manual
advertisement
PRODUCT GUIDE
MODEL 461334813
Thermos C34G
IMPORTANT: Fill out the product record information below.
Serial Number
See rating label on grill for serial number.
Date Purchased
For support and to register your grill, please visit us at www.charbroil.com
If you have questions or need assistance during assembly, please call 1-800-241-7548.
© 2013 Char-Broil, LLC Columbus, GA 31902 Printed in China Assembly instructions © 2013 09/03/12 • G451-001-270801
TABLE OF CONTENTS
For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Grilling Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26
Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.
Safety Symbols
The symbols and boxes shown below explain what each heading means. Read and follow all of the messages found throughout the manual.
WARNING
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION: Indicates a potentially hazardous situation or unsafe practice which, if not avoided, may result in minor or moderate injury.
WARNING
Failure to follow all manufacturer’s instructions could result in serious personal injury and/or property damage.
CAUTION cooking.
WARNING
1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
DANGER
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
INSTALLER/ASSEMBLER:
Leave this manual with consumer.
CONSUMER:
Keep this manual for future reference.
CAUTION
Read and follow all safety statements, assembly instructions, and use and care directions before attempting to assemble and cook.
CAUTION
Some parts may contain sharp edges.
Wear protective gloves if necessary.
THIS GRILL IS FOR OUTDOOR USE ONLY.
2
WARNING
CALIFORNIA PROPOSITION 65
1. Combustible by-products produced when using
this product contains chemicals known to the State
of California to cause cancer, birth defects, or
other reproductive harm.
2. This product contains chemicals, including lead
and lead compounds, known to the State of
California to cause cancer, birth defects or
other reproductive harm.
Wash your hands after handling this product.
CAUTION
Using pots larger than 6 quarts in capacity could exceed weight limit of the side burner shelf or side shelf, resulting in failure of grill cart components.
Installation Safety Precautions
• Use grill, as purchased, only with LP (propane) gas and the regulator/valve assembly supplied. If your grill is Dual Fuel ready, a conversion kit must be purchased for use with natural gas.
• Grill installation must conform with local codes, or in their absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and
Handling Code, B149.2.
• All electrical accessories (such as rotisserie) must be electrically grounded in accordance with local codes, or
National Electrical Code, ANSI / NFPA 70 or Canadian
Electrical Code, CSA C22.1. Keep any electrical cords and/or fuel supply hoses away from any hot surfaces.
• This grill is safety certified for use in the United States and/or
Canada only. Do not modify for use in any other location.
Modification will result in a safety hazard.
WARNING
Do not attempt to repair or alter the hose/valve/regulator for any “assumed” defect. Any modification to this assembly will void your warranty and create the risk of a gas leak and fire. Use only authorized replacement parts supplied by manufacturer.
CAUTION
Grease Fires
• Putting out grease fires by closing the lid is not possible. Grills are well ventilated for safety reasons.
• Do not use water on a grease fire. Personal injury may result. If a grease fire develops, turn knobs and LP tank off.
• If grill has not been regularly cleaned, a grease fire can occur that may damage the product. Pay close attention while preheating or burning off food residue to insure that a grease fire does not develop. Follow instructions on General Grill Cleaning and Cleaning The Burner
Assembly to prevent grease fires.
• The best way to prevent grease fires is regular cleaning of the grill.
NOTE: DO NOT over tighten screws and washers that come into contact with porcelain coated surfaces. Over tightening may cause the porcelain coating to crack and break, resulting in exposed metal that will be prone to rust.
3
4
GRILLING GUIDE – Getting Started
First Time Use
Read your Assembly Manual and ensure the grill is put together properly. Remove all Point-of-Purchase advertising material from all grill surfaces before first use. We recommend operating your grill on its highest setting for 15-20 minutes prior to your first use.
This aids in removing the oils used during manufacturing.
Lava Rock / Briquettes
This gas grill has been designed, engineered, and tested to be used with flame tamers or heat distribution plates to provide more even heating, improve the cleaning process, and reduce flare-ups. The addition of after market lava rocks, charcoal, or briquettes of any type will cause poor combustion and increase the likelihood of a grease fire, and is not recommended. Using briquettes, lava rock, or charcoal in this grill will void your warranty. For extra smoke flavor, we recommend using a smoker box with wood chips.
Temperature - Convective Grills ONLY.
The temperature gauge in the hood of your new grill measures air temperature. The air temperature inside your grill will never be as hot as the temperature at the cooking surface.
Note: Since 1995, all regulators (the part that attaches to the gas tank to regulate the flow of gas) have included a safety feature that restricts gas flow in the event of a gas leak. You can inadvertently activate this safety feature without having a gas leak. This typically occurs when you turn on the gas using the grill control knob before you turn on the LP tank valve. If the gas regulator safety feature activates, the grill will only reach temperatures between 250°F and 300°F even with all burners on the high setting.
Regulator Coupling Nut
If your grill is not getting hotter than 250°F to 300°F these steps should be taken first to reset the gas regulator safety device:
1. Open the grill lid.
2. Turn off all knobs on the control panel in front.
3. Turn off the tank knob.
4. Disconnect the regulator from the LP tank.
5. Wait 30 seconds.
6. Reconnect the regulator to the LP tank.
7. Slowly open the LP tank knob all the way. Do not put excessive force on the valve at the full open position to avoid damaging the valve.
8. Turn on the appropriate control knob and light the grill per the instructionsl.
An illustration of this process is included in this Product Guide.
See Troubleshooting section for additional information.
Pre-Heating Your Grill
Just like your home oven, your grill should be pre-heated to provide optimum performance. Pre-heat the grill on high for 10-
15 minutes – longer if weather conditions require. Please refer to the lighting instructions inside the Product Guide if you have questions about how to light your grill. A match-light chain and hole is provided for your convenience.
GRILLING GUIDE – Grilling 101
Outdoor grilling is really quite simple. You'll succeed with burgers, dogs, or steaks usually on your very first try. With experience, you will learn how to work with your grill, creating more imaginative meals all the time. This knowledge makes up the art of grilling. Before you start grilling, organize your food according to cooking technique and required cooking time, and optimize the use of your grilling area.
Direct Cooking
Direct cooking involves grilling your meat directly over high heat.
It is perfect for searing steaks, chops, and other smaller pieces of meat and vegetables that quickly make their way to the table.
Rotisserie Cooking
Rotisserie cooking is best for 'round' meat, such as large roasts, whole poultry, and pork. It generally requires an accessory motor and spit rod that allows the meat to be turned at a constant speed. Rotisserie cooking is best done in front of a special rotisserie burner, or utilizing an indirect cooking burner arrangement. A pan can be placed underneath the meat to catch grease and food drippings, and helps minimize clean-up.
Indirect Cooking
Indirect cooking utilizes select burners to circulate heat throughout the grill, without direct contact between the meat and the flame. The meat is placed over the burner that is 'off'. This method is generally used to slow cook large cuts of meat and poultry. A pan can be placed underneath the meat to catch grease and food drippings, and helps minimize clean-up.
Food Safety
Food safety is a very important part of enjoying the outdoor cooking experience. To keep food safe from harmful bacteria, follow these four basic steps:
Clean: Wash hands, utensils, and surfaces with hot soapy water before and after handling raw meat.
Separate: Separate raw meats from ready-to-eat foods to avoid cross contamination. Use a clean platter and utensils when removing cooked foods.
Cook: Cook meat and poultry thoroughly to kill bacteria. Use a thermometer to ensure proper internal food temperatures.
Chill: Refrigerate prepared foods and leftovers promptly.
5
6
GRILLING GUIDE – Tips & Tricks
Cooking on your new grill is a hands-on experience, and it is recommended to remain outside with your grill while cooking.
Grilling can be affected by many external conditions. In cold weather, you will need more heat to reach an ideal cooking temperature, and grilling may take longer. The meat's internal temperature and thickness can also affect cooking times. Cold and thicker meats will take longer to cook.
Internal Meat Temperatures
Meat cooked on a grill often browns very fast on the outside.
Therefore, use a meat thermometer to ensure it has reached safe internal temperatures.
USDA Recommended Safe Minimum
Internal Temperatures
Beef, Veal, Lamb, Steak, Roasts, & Whole Pork
(with a 3 minute rest time)
145° F
Fish
Beef, Veal, Lamb, and Pork - Ground
Egg Dishes
Turkey, Chicken & Duck Whole, Pieces & Ground
145° F
160° F
160° F
165° F
Please refer to the USDA for complete, up-to-date information.
Our internal temperature chart is based on USDA standards for meat doneness. Check it out at www.isitdoneyet.gov
Sauces
Sauces containing sugars and fats can cause flare-ups, and your food may burn. In general, apply these sauces during the final
10 minutes of cooking. Keep in mind, use of excessive sauces or glazes will also require extra cleaning afterwards.
Marinades and Rubs
To enhance the flavor of grilled foods, a liquid marinade or dry rub can be used prior to cooking. Meat can be either soaked or injected with liquid marinade up to 24 hours prior to grilling. Dry rubs can be applied directly to the meat immediately before grilling.
Wood Chips
For extra smoke flavor when grilling, try adding wood chips.
Soak the chips in water for approximately 30 minutes before adding to a smoke box or pan. Place smoke box or pan on top of the cooking grate above the flame. Turn grill on high until the wood starts to smoke. Reduce heat to desired temperature for cooking, and place food on cooking grate as desired. Close lid to retain more smoke. Hardwood varieties that work particularly well with grilled foods include Alder, Apple, Cherry, Grapevines,
Hickory, Mesquite, Oak, Rosemary and Sassafras.
Skewers
Metal skewers should be flat, with long handles. Round skewers allow food to roll when turned, so it may not cook as evenly. Use metal skewers when cooking meat kabobs. Wooden skewers should be soaked in water for an hour before use, and are best used for quick cooking foods such as vegetables and fruits.
Utensils
Use tongs or a spatula to handle the food instead of a fork, and don't turn the food too often. Piercing the food with a fork will release juices that you want in the meat, and may cause flare-ups.
GRILLING GUIDE – Cleaning Your Grill
Why Clean?
We've all heard the saying 'An ounce of prevention is worth a pound of cure'. This is great advice when it comes to keeping your grill clean.
Routine Care
Periodic cleaning of this grill is necessary, as grill fires can occur when grease and food debris collect in the bottom of the grill.
After each use, remove any remaining food particles from the cooking grate and inside of the grill using a grill brush. Do this after the grill has cooled down, yet is still warm. It is much easier to clean food particles while warmth is still present, than after the food particles have completely cooled and hardened. This grill is not designed to be 'burned off' by closing the lid and turning the burners on High for an extended time. The excessive heat generated can cause leftover grease to catch fire, and can cause permanent damage to your grill.
General Cleaning
Plastic parts: Wash with warm soapy water and wipe dry. Do not use abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.
Porcelain surfaces: Because of glass-like composition, most residue can be wiped away with baking soda/water solution or glass cleaner. Use non-abrasive scouring powder for stubborn stains.
Painted surfaces: Wash with mild detergent or non-abrasive cleaner and warm water. Wipe dry with a soft non-abrasive cloth.
Stainless steel surfaces: Stainless steel can rust under certain conditions. This can be caused by environmental conditions such as chlorine or salt water, or improper cleaning tools such as wire or steel wool. It can also discolor due to heat, chemicals, or grease build-up. To maintain your grill's high quality appearance, wash with mild detergent and warm water, or use a stainless steel grill cleaner. Baked-on grease deposits may require the use of an abrasive plastic cleaning pad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with graphics.
Cooking surfaces: If a bristle brush is used to clean any of the grill cooking surfaces, ensure no loose bristles remain on cooking surfaces prior to grilling. It is not recommended to clean cooking surfaces while grill is hot.
Storing Your Grill
• Clean cooking grates.
• Store grill in dry location.
• When LP cylinder is connected to grill, store outdoors in a well ventilated space and out of reach of children.
• Cover grill if stored outdoors. Choose from a variety of grill covers offered by manufacturer.
• Store grill indoors ONLY if LP cylinder is turned off, disconnected, and removed from grill. Never store LP cylinder indoors.
• When removing grill from storage, follow the 'Cleaning the
Burner Assembly' instructions in the Use and Care section of the Product Guide.
Critters
Spiders like to make their homes in the venturi tubes of grills.
These must be inspected and cleaned regularly to ensure there are no blockages. Refer to the Use and Care portion of this
Product Guide for complete information.
The Char-Broil® grill is equipped with Gear Trax™, which allow for the easy mounting of our unique line of Gear Trax accessories. Please visit charbroil.com for a complete list of Gear Trax accessories. *Available on most models.
VISIT CHARBROIL.COM FOR
ALL YOUR GRILLING NEEDS!
7
USE AND CARE
DANGER
• NEVER store a spare LP cylinder under or near the appliance or in an enclosed area.
LP Cylinder
•The LP cylinder used with your grill must meet the following requirements:
•Use LP cylinders only with these required measurements: 12"
(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum.
•LP cylinders must be constructed and marked in accordance with specifications for LP cylinders of the U.S. Department of
Transportation (DOT) or for Canada, CAN/CSA-B339, cylinders, spheres and tubes for transportation of dangerous goods. Transport Canada (TC). See LP cylinder collar for marking.
•LP cylinder valve must have:
•Type 1 outlet compatible with regulator or grill.
•Safety relief valve.
•UL listed Overfill Protection
Device (OPD). This OPD safety
OPD Hand Wheel feature is identified by a unique triangular hand wheel. Use only LP cylinders equipped with this type of valve.
•LP cylinder must be arranged for vapor withdrawal and include collar to protect LP cylinder valve. Always keep LP cylinders in upright position during use, transit or storage.
• Never fill a cylinder beyond 80% full.
• An over filled or improperly stored cylinder is a hazard due to possible gas release from the safety relief valve. This could cause an intense fire with risk of property damage, serious injury or death.
• If you see, smell or hear gas escaping, immediately get away from the LP cylinder/appliance and call your fire department.
LP Cylinder Removal, Transport and Storage
•Turn OFF all control knobs and LP cylinder valve. Turn coupling nut counterclockwise by hand only - do not use tools to disconnect. Loosen cylinder screw beneath bottom shelf or disconnect other retention means, then lift PL cylinder up and and out of cart. Install safety cap onto LP cylinder valve.
Always use cap and strap supplied with valve.
Failure to use safety cap as directed may result in serious personal injury and/or property damage.
8
•A disconnected LP cylinder in LP Cylinder Valve storage or being transported must have a safety cap installed (as shown).
Do not store an LP cylinder in enclosed spaces such as a carport, garage, porch, covered patio or other building. Never leave an LP cylinder inside a vehicle which may become overheated by the sun.
Safety
Cap
Retainer Strap
•Do not store an LP cylinder in an area where children play.
LP cylinder in upright position for vapor withdrawal
LP (Liquefied Petroleum Gas)
•LP gas is nontoxic, odorless and colorless when produced. For
Your Safety, LP gas has been given an odor (similar to rotten cabbage) so that it can be smelled.
•LP gas is highly flammable and may ignite unexpectedly when mixed with air.
LP Cylinder Filling
•Use only licensed and experienced dealers.
•LP dealer must purge new cylinder before filling.
•Dealer should NEVER fill LP cylinder more than 80% of LP cylinder volume. Volume of propane in cylinder will vary by temperature.
•A frosty regulator indicates gas overfill. Immediately close LP cylinder valve and call local LP gas dealer for assistance.
•Do not release liquid propane (LP) gas into the atmosphere.
This is a hazardous practice.
•To remove gas from LP cylinder, contact an LP dealer or call a local fire department for assistance. Check the telephone directory under “Gas Companies” for nearest certified LP dealers.
LP Cylinder Exchange
•Many retailers that sell grills offer you the option of replacing your empty LP cylinder through an exchange service. Use only those reputable exchange companies that inspect, precision fill, test and certify their cylinders. Exchange your cylinder only for an OPD safety feature-equipped cylinder as described in the "LP Cylinder" section of this manual.
•Always keep new and exchanged LP cylinders in upright position during use, transit or storage.
•Leak test new and exchanged LP cylinders BEFORE connecting to grill.
•Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps
or plugs may result in leakage of propane.
Connecting Regulator to the LP Cylinder
1.LP cylinder must be properly secured onto grill. (Refer to assembly section.)
2.Turn all control knobs to the OFF position.
3.Turn LP cylinder OFF by turning hand-wheel clockwise to a
full stop.
4.Remove the protective cap from LP cylinder valve. Always use cap and strap supplied with valve.
O f f C l o ck w is e
OPD Hand Wheel
Type 1 outlet with thread on outside
LP Cylinder Leak Test
For your safety
•Leak test must be repeated each time LP cylinder is exchanged or refilled.
•Do not smoke during leak test.
•Do not use an open flame to check for gas leaks.
•Grill must be leak tested outdoors in a well-ventilated area, away from ignition sources such as gas fired or electrical appliances. During leak test, keep grill away from open flames or sparks.
•Use a clean paintbrush and a 50/50 mild soap and water solution. Brush soapy solution onto areas indicated by arrows in figure below.
▲
Do not use household cleaning agents. Damage to gas train components can result.
Safety Relief Valve
Strap and Cap
Do not use a POL transport plug
(plastic part with external threads)!
It will defeat the safety feature of the valve.
5.Hold regulator and insert nipple into LP cylinder valve. Hand-tighten the coupling nut, holding regulator in a straight line with LP cylinder valve so as not to cross-thread the connection.
WARNING
If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department!
Nipple has to be centered into the LP cylinder valve.
9
Straight
Hold coupling nut and regulator as shown for proper connection to LP cylinder valve.
Leak Testing Valves, Hose and Regulator
1.Turn all grill control knobs to OFF.
2.Be sure regulator is tightly connected to LP cylinder.
3.Completely open LP cylinder valve by turning hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct
before proceeding.
4.Brush soapy solution onto areas circled below, or other similar fittings on your grill.
6.Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools.
NOTE:
If you cannot complete the connection, disconnect regulator and repeat steps 5 and 6. If you are still unable to complete the connection, do not use this regulator!
DANGER
• Do not insert any tool or foreign object into the valve outlet or safety relief valve. You may damage the valve and cause a leak. Leaking propane may result in explosion, fire, severe personal injury, or death.
10
WARNING
• Outdoor gas appliance is not intended to be installed in or on a boat.
• Outdoor gas appliance is not intended to be installed in or on an RV.
• Never attempt to attach this grill to the self-contained
LP gas system of a camper trailer or motor home.
• Do not use grill until leak-tested.
• If a leak is detected at any time, STOP and call the fire department.
• If you cannot stop a gas leak, immediately close
LP cylinder valve and call LP gas supplier or your fire department!
NOTE: Sideburner shelf fascia not shown for clarity.
NOTE: Your grill may NOT be equipped with a sideburner.
5.If “growing” bubbles appear, there is a leak. Close LP cylinder valve immediately and retighten connections. If leaks
cannot be stopped do not try to repair. Call for replacement parts.
6.Always close LP cylinder valve after performing leak test by turning hand wheel clockwise.
WARNING
For Safe Use of Your Grill and to Avoid Serious
Injury:
• Do not let children operate or play near grill.
• Keep grill area clear and free from materials that burn.
• Do not block holes in sides or back of grill.
• Check burner flames regularly.
• Use grill only in well-ventilated space. NEVER use in enclosed space such as carport, garage, porch, covered patio, or under an overhead structure of any kind.
•
• Do not use charcoal or ceramic briquets in a gas grill.
(Unless briquets are supplied with your grill.)
Do not cover grates with aluminum foil or any other material. This will block burner ventilation and create a potentially dangerous condition resulting in property damage and/or personal injury.
• Use grill at least 3 ft. from any wall or surface.
Maintain 10 ft. clearance to objects that can catch fire or sources of ignition such as pilot lights on water heaters, live electrical appliances, etc.
• Apartment Dwellers:
Check with management to learn the requirements and fire codes for using an LP gas grill in your apartment complex. If allowed, use outside on the ground floor with a three (3) foot clearance from walls or rails. Do not use on or under balconies.
• NEVER attempt to light burner with lid closed. A buildup of non-ignited gas inside a closed grill is hazardous.
• Never operate grill with LP cylinder out of correct position specified in assembly instructions.
• Always close LP cylinder valve and remove coupling nut before moving LP cylinder from specified operation position.
Safety Tips
▲ Before opening LP cylinder valve, check the coupling nut for tightness.
▲
▲
▲
When grill is not in use, turn off all control knobs and LP cylinder valve.
Never move grill while in operation or still hot.
Use long-handled barbecue utensils and oven mitts to avoid burns and splatters.
▲
▲
Maximum load for sideburner and side shelf is 10 lbs.
The grease tray or cup must be installed during use and
emptied after each use. Do not remove grease tray or cup until grill has completely cooled.
▲ Clean grill often, preferably after each cookout. If a bristle brush is used to clean any of the grill cooking surfaces,
▲
▲
▲
▲
▲
▲ ensure no loose bristles remain on cooking surfaces prior to grilling. It is not recommended to clean cooking surfaces while grill is hot.
If you notice grease or other hot material dripping from grill onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve, hose and regulator before continuing. Perform a leak test.
Keep ventilation openings in cylinder enclosure (grill cart) free and clear of debris.
Do not store objects or materials inside the grill cart enclosure that would block the flow of combustion air to the underside of either the control panel or the firebox bowl.
The regulator may make a humming or whistling noise during operation. This will not affect safety or use of grill.
If you have a grill problem see the "Troubleshooting Section".
If the regulator frosts, turn off grill and LP cylinder valve immediately. This indicates a problem with the cylinder and it should not be used on any product. Return to supplier!
Ignitor Lighting
▲ Do not lean over grill while lighting.
1. Turn OFF gas burner control valves.
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
4. To ignite, turn IGNITION BURNER knob to the HIGH position.
5. Push IGNITOR button rapidly.
6. If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure.
7. Ignite remaining burners by turning to the HIGH position, starting with the burners closest to the IGNITION BURNER first.
If ignition still does not occur, follow match-lighting instructions.
Lighting instructions are continued on the next page
11
WARNING
Turn controls and gas source or tank OFF when not in use.
Burner Flame Check
• Remove cooking grates and flame tamers. Light burners, rotate knobs from HIGH to LOW. You should see a smaller flame in
LOW position than seen on HIGH. Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section.
HIGH
LOW
CAUTION
If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with the valve open, gas will continue to flow out of the burner and could accidently ignite with risk of injury.
Match-Lighting
▲
Do not lean over grill while lighting.
1. Turn OFF gas burner control valves.
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
4. Place match into match holder (hanging from side of cart).
Strike the match.
5. Place lit match through the match light hole and near the burner. Push in and turn left knob to the HIGH position. Be sure the burner lights and stays lit.
6. Light adjacent burners in sequence by pushing knobs in and turning to the HIGH position.
Turning Grill Off
• Turn all knobs to the OFF position. Turn LP cylinder OFF by turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic ignitor button. "Click" should be heard and spark seen each time between each collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in OFF position. To check valves, first push in knobs and release, knobs should spring back. If knobs do not spring back, replace valve assembly before using grill. Turn knobs to LOW position then turn back to
OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn or linked.
Replace damaged hoses before using grill. Use only valve/hose/regulator specified by manufacturer.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and smoke for paint. Interiors of gas grills are not painted at the factory (and should never be painted). Apply a strong solution of detergent and water or use a grill cleaner with scrub brush on insides of grill lid and bottom. Rinse and allow to completely air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
▲
Do not use citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.
• Porcelain surfaces: Because of glass-like composition, most residue can be wiped away with baking soda/water solution or specially formulated cleaner. Use nonabrasive scouring powder for stubborn stains.
• Painted surfaces: Wash with mild detergent or nonabrasive cleaner and warm soapy water. Wipe dry with a soft nonabrasive cloth.
• Stainless steel surfaces: To maintain your grill’s high quality appearance, wash with mild detergent and warm soapy water and wipe dry with a soft cloth after each use. Baked-on grease deposits may require the use of an abrasive plastic cleaning pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of the grill cooking surfaces, ensure no loose bristles remain on cooking surfaces prior to grilling. It is not recommended to clean cooking surfaces while grill is hot.
12
CAUTION
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER
3.
Remove carryover tubes and burners.
4.
Detach electrode from burner.
NOTE: Removal/Detachment method will depend on the burner configuration. See different configurations in illustrations below.
5.
Carefully lift each burner up and away from valve openings.
We suggest three ways to clean the burner tubes. Use the one easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook through each burner tube several times.
If your barbeque is getting hard to light or the flame is weak, check and clean the venturis and burners.
Storing Your Grill
• Clean cooking grates.
• Store in dry location.
• When LP cylinder is connected to grill, store outdoors in a wellventilated space and out of reach of children.
• Cover grill if stored outdoors. Choose from a variety of grill covers offered by manufacturers.
• Store grill indoors ONLY if LP cylinder is turned off and disconnected, removed from grill and stored outdoors.
• When removing grill from storage, follow “Cleaning the Burner
Assembly” instructions before starting grill.
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill.
1. Turn gas OFF at control knobs and LP cylinder.
2. Remove cooking grates and flame tamers.
(B) Use a narrow bottle brush with a flexible handle (do not use a brass wire brush), run the brush through each burner tube several times.
(C) Wear eye protection: Use an air hose to force air into the burner tube and out the burner ports. Check each port to make sure air comes out each hole.
6.
Wire brush entire outer surface of burner to remove food residue and dirt.
7.
Clean any blocked ports with a stiff wire such as an open paper clip.
8.
Check burner for damage, due to normal wear and corrosion some holes may become enlarged. If any large cracks or holes are found replace burner.
VERY IMPORTANT: Burner tubes must reengage valve openings. See illustrations at right.
9. Attach electrode to burner.
10. Carefully replace burners.
11. Attach burners to brackets on firebox.
Correct burner-to-valve engagement
12. Reposition carryover tubes and attach to burners. Replace flame tamers and cooking grates.
Remove screws
Firebox
Carr yover tube
Firebox
Firebox burner bracket
Carryover tube
Electrode
Electrode
Firebox burner bracket
Pry off electrode with a flat blade screwdriver
13
LIMITED WARRANTY
This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or freight pre-paid by the consumer for review and examination.
SCOPE OF COVERAGE
Stainless Burner
Firebox and Lid
All Other Parts
PERIOD OF COVERAGE
5 years from date of purchase*
2 years from date of purchase*
1 year from date of purchase*
TYPE OF FAILURE COVERAGE
PERFORATION, MANUFACTURING,
AND MATERIAL DEFECTS ONLY
*Note: A dated sales receipt WILL be required for warranty service.
The original consumer-purchaser will be responsible for all shipping charges for parts replaced under the terms of this limited warranty.
This limited warranty is applicable in the United States and Canada only, is only available to the original owner of the product and is not transferable.
Manufacturer requires proof of your date of purchase. Therefore, you should retain your sales slip or invoice. Registering your product is not a substitute for proof of purchase and the manufacturer is not responsible for or required to retain proof of purchase records.
This limited warranty applies to the functionality of the product ONLY and does not cover cosmetic issues such as scratches, dents, corrosions or discoloring by heat, abrasive and chemical cleaners or any tools used in the assembly or installation of the appliance, surface rust, or the discoloration of stainless steel surfaces. RUST is not considered a manufacturing or materials defect.
This limited warranty will not reimburse you for the cost of any inconvenience, food, personal injury or property damage.
ITEMS MANUFACTURER WILL NOT PAY FOR:
1. Shipping cost, standard or expedited, for warranty and replacement parts
2. Service calls to your home.
3. Repairs when your product is used for other than normal, single-family household or residential use.
4. Damage, failures, or operating difficulties resulting from accident, alteration, careless handling, misuse, abuse, fire, flood,
acts of God, improper installation or maintenance, installation not in accordance with electrical or plumbing codes, or use of products not approved by the manufacturer.
5. Any food loss due to product failures or operating difficulties.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Pickup and delivery of your product.
8. Repairs to parts or systems resulting from unauthorized modifications made to the product.
9. The removal and/or reinstallation of your product.
DISCLAIMER OF IMPLIED WARRANTIES and LIMITATION OF REMEDIES
Repair or replacement of defective parts is your exclusive remedy under the terms of this limited warranty. In the event of parts availability issues, the manufacturer reserves the right to substitute like or similar parts that are equally functional.
Manufacturer will not be responsible for any consequential or incidental damages arising from the breach of either this limited warranty or any applicable implied warranty, or for failure or damage resulting from acts of God, improper care and maintenance, grease fire, accident, alteration,
replacement of parts by anyone other than Manufacturer, misuse, transportation, commercial use, abuse, hostile environments (inclement weather,
acts of nature, animal tampering), improper installation or installation not in accordance with local codes or printed manufacturer instructions.
THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY GIVEN BY THE MANUFACTURER. NO PRODUCT PERFORMANCE
SPECIFICATION OR DESCRIPTION WHEREVER APPEARING IS WARRANTED BY MANUFACTURER EXCEPT TO THE EXTENT SET
FORTH IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTY PROTECTION ARISING UNDER THE LAWS OF ANY STATE,
INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, IS HEREBY
LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY.
Neither dealers nor the retail establishment selling this product has any authority to make any additional warranties or to promise remedies
in addition to or inconsistent with those stated above. Manufacturer's maximum liability, in any event, shall not exceed the purchase price of the product paid by the original consumer.
NOTE: Some states do not allow an exclusion or limitation of incidental or consequential damages, so some of the above limitations or exclusions may not apply to you. This limited warranty gives you specific legal rights as set foth herein. You may also have other rights which vary from state to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this product or the Manufacturer will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer-purchaser prior to discovery of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment selling this product in order to obtain performance under this limited warranty.
If you wish to obtain performance of any obligation under this limited warranty, you should write to:
Consumer Relations
P. O. Box 1240
Columbus, GA 31902-1240
Consumer returns will not be accepted unless a valid Return Authorization is first acquired. Authorized returns are clearly marked on the outside of the package with an RA number and the package is shipped freight/postage pre-paid. Consumer returns that do not meet these standards will be refused.
14
PARTS LIST
BB
CC
DD
EE
W
X
Y
Z
AA
FF
GG
HH
II
U
V
S
T
Q
R
O
P
L
M
J
K
N
H
I
F
G
Key Qty Description
A 1 LEFT LEG ASSEMBLY
D
E
B
C
1
1
1
1
MATCH HOLDER
RIGHT LEG ASSEMBLY
BOTTOM SHELF
TANK THUMBSCREW
1
1
2
2
2
2
1
1
1
REAR CART BRACE
AXLE ROD
WHEEL
LEG EXTENDER
TANK EXCLUSION WIRE
FRONT PANEL
TOP LID
TEMPERATURE GAUGE
BEZEL, F/ TEMPERATURE GAUGE
1
2
2
1
1
1
3
1
2
1
1
1
3
3
1
1
HANDLE F/ TOP LID
LID BUMPER, RECTANGLE
REAR RUBBER BUMPER, F/ MAIN LID
LOGO PLATE
TOP LID HARDWARE
FIREBOX
MAIN BURNER
ELECTRODE, MAIN BURNER
FLAME CARRY OVER TUBE
MAIN CONTROL PANEL
IGNITOR
HOSE VALVE REGULATOR
CONTROL KNOB
1 RIGHT SIDE SHELF
1 FASCIA, F/ RIGHT SHELF
1 LEFT SIDE SHELF
1 FASCIA, F/ LEFT SHELF
3 HEAT TENT
COOKING GRATE
CLIP, F/ GREASE CUP
GREASE CUP
NOT Pictured
… 1 PRODUCT MANUAL, ENGLISH
…
…
1 PRODUCT MANUAL, SPANISH
1 HARDWARE PACK
NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same.
15
PARTS DIAGRAM
L
S
Y
AA
AA
AA
GG
LL
GG
GG
FF
U
W
V
FF
U
FF
W
U
Q
T
P
R
O
N M
DD
EE
BB
X
CC
Z C
A
K
B
F
HH
J
II
J
E
K
I
G D
16
H
ASSEMBLY
1
Place bottom shelf with cut out hole for LP tank next to legs with axle holes.
Attach to right and left leg assemblies with 1/4-20x1-1/2" screws and 1/4-20 flange nuts.
Left Leg Assembly
Bottom Shelf
Right Leg Assembly
Axle Hole
2
Attach rear brace to cart with 1/4-20x1/2" machine screws.
Right Leg Assembly
Rear Brace
1/4-20
Flange Nut
Qty. 4
1/4-20x1-1/2"
Machine Screw
Qty. 4
1/4-20x1/2"
Machine Screw
Qty. 4
Right Leg Assembly
17
18
ASSEMBLY
3
Attach the lower front panel to legs with #8x3/8" sheet metal screws.
Attach the upper front panel to legs and lower front panel with #8x3/8" sheet metal screws.
#8x3/8"
Sheet Metal Screw
Qty. 9
Lower Front Panel
Upper Front Panel
4
1” Hitch Pin
Qty. 1
Turn assembly upside down.
Insert axle rod through wheel, axle spacer, legs and other axle spacer and wheel. Attach with (1) 8mm flat washer and hitch pin.
Push leg extenders into right legs.
Leg Extender
Axle Rod
Wheel
Axle Spacer
Qty. 2
Axle Washer
Qty. 1
"Cone" side of wheel against leg
Axle Spacer
Axle Washer
Hitch Pin
5
Stand cart upright.
Hook tank exclusion wires onto the holes on front panels. Insert the other ends into the holes on rear brace as shown.
Tank Exclusion Wire
Rear Brace
19
20
6
This step requires two people to lift and position grill head onto cart.
Carefully lower the grill head onto the cart. Make sure the regulator hose is hanging outside the cart. Attach with
1/4-20x1/2" machine screws.
Grill Head
1/4-20x1/2"
Machine Screw
Qty 4
Regulator Hose
7
Install right side shelf onto the pre-installed screws located on the right side of firebox (A).
Tighten the pre-installed screws securely. Attach side shelf with (2) 1/4-20x1/2" screws as shown (B).
A
B
1/4-20x1/2"
Machine Screw
Qty. 2
8
Attach fascia to firebox with #8x3/8" sheet metal screws.
1/4-20x1/2" Screw
Tighten the screws
#8x3/8"
Sheet Metal Screw
Qty. 2
21
9
Install left side shelf onto the pre-installed screws located on the right side of firebox (A).
Tighten the pre-installed screws securely. Attach side shelf with (2) 1/4-20x1/2" screws as shown (B).
A
C
1/4-20x1/2"
Machine Screw
Qty. 2
10
Attach fascia to firebox with #8x3/8" sheet metal screws.
1/4-20x1/2" Screw
Tighten the screws
22
#8x3/8"
Sheet Metal Screw
Qty. 2
11
Place heat tents over burners by inserting tabs into slots in front of firebox. Note: Notch on the end of heat tents should fit over protrusions on the rear wall of firebox.
Back of Firebox
Heat T ent
Front of Firebox
Heat T ent
12
Place cooking grates onto grate rests.
Cooking Grate
23
13
Hang grease cup clip from bottom of firebox and place grease cup into grease cup clip.
Grease Cup Clip
Grease Cup
CAUTION
Failure to install grease cup clip and cup
will cause hot grease to drip from bottom of grill with risk of fire or property damage.
14
LP tank is sold separately. Use only with an OPD (over-fill protection device) equipped LP tank. Fill and leak-check before attaching to grill and regulator. See Use and Care section to correctly Leak Test and perform the Burner
Flame Check.
Place Lp tank into hole in bottom shelf with tank collar opening facing to side as shown. Finger tighten tank retainer screw to hold LP tank securely in place.
Always keep LP cylinders in upright position during use, transport, and storage.
CAUTION
Failure to install tank correctly may allow gas hose to be damaged in operation, resulting in the risk of fire.
Regulator
LP Cylinder
(not included)
LP Tank
Tank Thumbscrew
24
DANGER: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.
Emergencies
Gas leaking from cracked/cut/burned hose.
Possible Cause
•Damaged hose.
Prevention/Solution
•Turn off gas at LP cylinder or at source on natural gas systems. If anything but burned, replace valve/hose/regulator. If burned, discontinue use of product until a plumber has investigated cause and corrections are made.
•Replace LP cylinder.
Gas leaking from LP cylinder.
Gas leaking from LP cylinder valve.
Gas leaking between
LP cylinder and regulator connection.
Fire coming through control panel.
Grease fire or continuous excessive flames above cooking surface.
•Mechanical failure due to rusting or mishandling.
• Failure of cylinder valve from mishandling or mechanical failure.
•Improper installation, connection not tight, failure of rubber seal.
• Fire in burner tube section of burner due to blockage.
• Too much grease buildup in burner area.
• Turn off LP cylinder valve. Return LP cylinder to gas supplier.
•Turn off LP cylinder valve. Remove regulator from cylinder and visually inspect rubber seal for damage. See LP Cylinder Leak Test and Connecting Regulator to the LP Cylinder.
•Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die down. After fire is out and grill is cold, remove burner and inspect for spider nests or rust. See Natural Hazard and Cleaning the Burner Assembly pages.
• Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die down. After cooling, clean food particles and excess grease from inside firebox area, grease cup, and other surfaces.
Troubleshooting
Problem
Burner(s) will not light using ignitor.
Continued on next page.
Possible Cause
GAS ISSUES:
• Trying to light wrong burner.
• Burner not engaged with control valve.
• Obstruction in burner.
• No gas flow.
• Vapor lock at coupling nut to LP cylinder.
• Coupling nut and LP cylinder valve not fully connected.
ELECTRICAL ISSUES:
•Electrode cracked or broken; “sparks at crack.”
•Electrode tip not in proper position.
•Wire and/or electrode covered with cooking residue.
•Wires are loose or disconnected.
•Wires are shorting (sparking) between ignitor and electrode.
Prevention/Solution
• See instructions on control panel and in Use and Care section.
• Make sure valves are positioned inside of burner tubes.
• Ensure burner tubes are not obstructed with spider webs or other matter. See cleaning section of Use and Care.
• Make sure LP cylinder is not empty. If LP cylinder is not empty, refer to “Sudden drop in gas flow.”
• Turn off knobs and disconnect coupling nut from LP cylinder.
Reconnect and retry.
• Turn the coupling nut approximately one-half to three-quarters additional turn until solid stop. Tighten by hand only - do not use tools.
• Replace electrode(s).
Main Burners:
• Tip of electrode should be pointing toward gas port opening on burner. The distance should be 1/8” to 1/4”. Adjust if necessary.
Sideburner (if featured):
• Tip of electrode should be pointing toward gas port opening on burner. the distance should be 1/8” to 3/16”. Adjust if necessary.
•Clean wire and/or electrode with rubbing alcohol and clean swab.
•Reconnect wires or replace electrode/wire assembly.
•Replace ignitor wire/electrode assembly.
25
Troubleshooting (continued)
Problem
Burner(s) will not light using ignitor.
Possible Cause
PIEZO PUSH-BUTTON AND ROTARY:
•Push-button sticks at bottom.
•Rotary knob rotates without clicking.
•Sparking between ignitor and electrode.
Prevention/Solution
•Replace ignitor.
•Replace knob.
•Inspect wire insulation and proper connection. Replace wires if insulation is broken.
Burner(s) will not match light.
•See “GAS ISSUES:” on previous page.
•Match will not reach.
•Improper method of match-lighting.
Low flame, drop in gas flow.
•Out of gas.
•Excess flow valve tripped.
•Vapor lock at coupling nut/LP cylinder connection.
Flames blow out.
Flare-up.
•High or gusting winds.
•Low on LP gas.
•Excess flow valve tripped.
•Grease buildup.
•Excessive fat in meat.
•Excessive cooking temperature.
Persistent grease fire.
•Grease trapped by food buildup around burner system.
•Use long-stem match (fireplace match).
•See “Match-Lighting” section of Use and Care.
•Check for gas in LP cylinder.
•Turn off control and tank knobs, wait 30 seconds, turn tank knob on slowly, light grill. If flames are still low, turn off control and tank knobs and disconnect regulator. Reconnect regulator, turn tank knob on slowly, light grill.
•Turn off control and tank knobs and disconnect regulator. Reconnect regulator, turn on tank knob slowly, light grill.
•Turn front of grill to face wind or increase flame height.
•Refill LP cylinder.
•Refer to “Sudden drop in gas flow” above.
•Clean burners and inside of grill/firebox.
•Trim fat from meat before grilling.
•Adjust (lower) temperature accordingly.
•Turn knobs to OFF. Turn gas off at LP cylinder. Leave lid in position and let fire burn out. After grill cools, remove and clean all parts.
Flashback...
(fire in burner tube(s)).
•Burner and/or burner tubes are blocked.
Unable to fill LP cylinder.
•Some dealers have older fill nozzles with worn threads.
•Turn knobs to OFF. Clean burner and/or burner tubes. See burner cleaning section of Use and Care.
•The worn nozzles don’t have enough “bite” to engage the valve. Try a second LP dealer.
26
Please register your product online at:
Registre su producto en línea en:
Veuillez enregistrer votre produit à l'adresse: www.charbroil.com/register
(If you register online, you do not need to send in this registration card.)
(Si registra en línea, no es necesario enviar esta tarjeta de registro.)
(Si vous enregistrez votre produit en ligne, il n'est pas nécessaire d'envoyer la carte d'enregistrement.)
PLEASE FILL OUT THIS CARD AND ATTACH A COPY OF YOUR SALES RECEIPT. RETURN IT WITHIN 10 DAYS OF PURCHASE. FOR WARRANTY SERVICE PROOF OF PURCHASE
WILL BE REQUIRED. THIS WARRANTY IS NON-TRANSFERABLE.
LLENE ESTA TARJETA Y DEVUELVALA DENTRO DE LOS 10 DIAS DE LA COMPRA. PARA EL SERVICIO DE GARANTIA ES NECESARIO QUE PRESENTE SU COMPROBANTE DE
COMPRA. CONSERVE LA FACTURA. ESTA GARANTIA ES INTRANSFERIBLE.
VEUILLEZ COMPLETER CETTE CARTE ET LA RETOURNER DANS LES 10 JOURS SUIVANT L’ACHAT. POUR OBTENIR LE SERVICE SOUS GARANTIE, UNE PREUVE D’ACHAT DOIT
ETRE PRESENTEE. VEUILLEZ CONSERVER VOTRE FACTURE. LA PRESENTE GARANTIE N’EST PAS TRANSFERABLE.
*Required | Necesario | Exigé ~ PLEASE PRINT ~ IMPRIMA POR FAVOR ~ S'IL VOUS PLAÎT IMPRIMER ~
*❶
First Name | Nombre | Prénom Initial | Inicial | Initiale Last Name | Apellido | Nom de Famillie
*❷
Address (number & street) | Dirección (número y calle) | Adresse (numéro et rue)
City | Cludad | Ville State | Estado | Province
E-mail Address | Dirección de correo electrónico | Adresse électronique
Apt Number | Nº de apart | Nº d’appt.
Zip Code | Código Zip | Code Postal
* ❸
Phone Number | Número telefónico | Numéro de téléphone
*❹
Model Number | Número de modelo | Numéro de modèle
Serial Number | Número de serie| Numéro de série
STICKER ON PRODUCT
❻
Date of Purchase | Fecha de compra | Date de l’achat
❼
Store Name | Nombre de la tienda | Nom du magasin
$
❽
Purchase Price | Precio de compra | Prix d’achat
❾
Your Gender | Sexo | Sexe:
Male | Masculino | Masculin
Female | Femenino | Féminin
❿
Which product are you registering?
¿Qué producto está registrando?
Quel produit enregistrez-vous?
Mail to: / Enviar a: / Envoyer à :
1. Gas Grill | Parrilla a gas | Gril au gaz
2. Electric Grill | Parrilla eléctrica | Gril électrique
3. Smoker | Ahumador | Fumoir
4. Charcoal Grill | Parrilla a carbón | Barbecue au charbon
5. Cooker/Fryer | Cocina/freidora | Cuiseur/Friteuse
6. Other | Otro | Autre
Char-Broil Warranty Registration
P.O. Box 1240
Columbus, GA 31902-1240
* ❺ Attach copy of your sales receipt here.
Adjunte aqui la copia de su recibo de compra
Veuillez attacher une copie de votre reçu ici.
We respect your privacy. | Respetamos su privacidad. | Nous respectons votre vie privée.
If you prefer not to receive special offers and promotions from Char-Broil, please check here:
Marque aquí si no desea recibir ofertas y promociones especiales de Char-Broil:
Si vous préférez ne pas recevoir d’informations concernant des offres spéciales et des promotions de Charbroil, veuillez cocher ici:
Thank you for completing this questionnaire. | Gracias por completer este cuestionario. | Merci d’avoir bien voulu remplir ce questionnaire.
27
THANK YOU
FOR YOUR RECENT
PURCHASE FROM
CHECK OUT THESE
GREAT FEATURES
ON OUR WEBSITE
•
Valuable product information
•
Inspiring grilling accessories
•
Reliable customer support
•
Delicious recipes and tips from chefs
•
Exciting events and promotions
•
And much more!
REGISTER YOUR PRODUCT TO RECEIVE A
SPECIAL OFFER
CHARBROIL.COM/REGISTER
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
advertisement
Table of contents
- 2 For Your Safety
- 4 Grilling Guide
- 8 Use and Care
- 14 Limited Warranty
- 15 Parts List
- 16 Parts Diagram
- 17 Assembly
- 25 Troubleshooting
- 27 Registration Card