Sharp SL-550 Owner`s manual

Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.
Pour demander un exemplaire en français de ce Manuel
du propriétaire, visitez www.heatnglo.com.
Owner’s Manual
Installation and Operation
Models:
SL-550TR-E
SL-750TR-E
SL-950TR-E
SL-550TR-IPI-E
SL-750TR-IPI-E
SL-950TR-IPI-E
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas
- Do not try to light any appliance.
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
• Leave this manual with
party responsible for use
and operation.
D
DI O N
SC OT
AR
D
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
1
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
Congratulations
Congratulations on selecting a Heat & Glo gas appliance
—an elegant and clean alternative to wood burning
appliances. The Heat & Glo gas appliance you have
selected is designed to provide the utmost in safety,
reliability, and efficiency.
This Owner’s Manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
The information contained in this Owner’s Manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a new appliance, you’ll want to read and
carefully follow all of the instructions contained in this
Owner’s Manual. Pay special attention to all Cautions and
Warnings.
Your new Heat & Glo gas appliance will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of appliance products!
We recommend that you record the following pertinent
information about your appliance.
Homeowner Reference Information
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number:__________________________________________ Location on appliance: ____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
The model information regarding your specific appliance can be found on
the rating plate usually located in the control area of the appliance.
This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States)
4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495,
5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195,
6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2,
6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou
autres brevets americains et etrangers en attente).
Heat & Glo, a brand of Hearth & Home Technologies, Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
Type of Gas
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz):
NATURAL GAS
Gas and Electric
Information
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
ANSI Z21XX-XXXX · CSA 2.XX-MXX · UL307B
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
(Po. Col. d’eau)
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
Model Number
Serial Number
Table of Contents
1 Listing and Code Approvals
A.
B.
C.
D.
E.
F.
G.
H.
Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glass Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Combustible Materials Specification. . . . . . . . . . . . . .
Combustible Materials Specification . . . . . . . . . . . . . . . . .
Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for the Commonwealth of Massachusetts . .
4
4
4
4
5
5
5
6
J.
K.
L.
M.
Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . .
Install Decorative Wall Components (SLP only) . . . . . . . .
Heat Shield Requirements for Horizontal Termination . . .
Install Horizontal Termination Cap (DVP and SLP Pipe) .
9 Gas Information
A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2 Getting Started
10 Electrical Information
A. Design and Installation Considerations . . . . . . . . . . . . . . . 7
B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 7
C. Inspect Appliance and Components . . . . . . . . . . . . . . . . . . 7
A.
B.
C.
D.
E.
F.
3 Framing and Clearances
A.
B.
C.
D.
E.
Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 8
Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . . 9
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Elevated Hearth Systems . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4 Termination Locations
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 12
5 Vent Information and Diagrams
A.
B.
C.
D.
E.
Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Flex Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
14
15
16
6 Vent Clearances and Framing
A.
B.
C.
D.
Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . .
Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . .
Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . .
Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . .
27
28
29
30
7 Appliance Preparation
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 33
8 Installing Vent Pipe (DVP and SLP Pipe)
A.
B.
C.
D.
E.
F.
G.
H.
I.
Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . .
Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . .
Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . .
Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . .
Install Decorative Ceiling Components (SLP only). . . . . .
Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . .
Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . .
Install RF4-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
35
35
36
36
37
38
38
39
40
40
40
41
Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . .
Intellifire Ignition System Wiring . . . . . . . . . . . . . . . . . . . .
Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . .
Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Switch Installation for Fan (Optional) . . . . . . . . . . . .
44
44
45
45
47
47
11 Finishing
A.
B.
C.
D.
Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
49
50
52
12 Appliance Setup
A.
B.
C.
D.
E.
F.
G.
H.
Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . .
Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lava Rock, Mineral Wool/Ember Placement . . . . . . . . . .
Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grilles and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
53
53
54
55
57
57
57
13 Operating Instructions
A.
B.
C.
D.
Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . .
Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . .
After Appliance is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . .
58
59
61
61
14 Troubleshooting
A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 62
B. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 64
15 Maintaining and Servicing Appliance
A. Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
16 Reference Materials
A.
B.
C.
D.
E.
Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . .
Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . .
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
69
76
84
86
= Contains updated information.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
3
1
Listing and Code Approvals
A. Appliance Certification
C. BTU Specifications
MODELS: SL-550TR-E, SL-750TR-E, SL-950TR-E
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.88a-2007 • CSA 2.33a-2007
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for Use
at High Altitudes”.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental
room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.
Models
U.S. (0-2000 ft.) or
Canada (2000-4500 ft.)
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
15,000
13,500
14,600
13,140
16,900
15,210
17,600
15,840
20,900
18,810
#44
#45
#55
#56
#42
#43
#54
#55
#37
#38
SL-750TRLP-E (LP)
SL-750TRLP-IPIE (LP)
Canada
SL-950TR-E (NG)
SL-950TR-IPI-E (NG)
Canada
21,000
18,900
20,600
18,540
24,300
21,870
23,400
21,060
30,400
27,360
U.S.
30,800
23,000
#52
Canada
27,720
20,700
#53
U.S.
SL-550TR-E (NG)
SL-550TR-IPI-E (NG)
Canada
SL-550TRLP-E (LP)
SL-550TRLP-IPIE (LP)
Canada
SL-750TR-E (NG)
SL-750TR-IPI-E (NG)
Canada
SL-950TR-E (LP)
SL-950TR-IPI-E (LP)
U.S.
U.S.
U.S.
U.S.
D. High Altitude Installations
B. Glass Specifications
Hearth & Home Technologies appliances manufactured with
tempered glass may be installed in hazardous locations
such as bathtub enclosures as defined by the Consumer
Product Safety Commission (CPSC). The tempered glass
has been tested and certified to the requirements of ANSI
Z97.1 and CPSC 16 CFR 1202 (Safety Glazing Certification
Council SGCC# 1595 and 1597. Architectural Testing, Inc.
Reports 02-31919.01 and 02-31917.01).
This statement is in compliance with CPSC 16 CFR
Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
U.L. Listed gas appliances are tested and approved without
requiring changes for elevations from 0 to 2000 feet in the
U.S.A. and Canada.
When installing this appliance at an elevation above 2000
feet, it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Input
rate should be reduced by 4% for each 1000 feet above
a 2000 foot elevation in the U.S.A., or 10% for elevations
between 2000 and 4500 feet in Canada. If the heating
value of the gas has been reduced, these rules do not
apply. To identify the proper orifice size, check with the
local gas utility.
If installing this appliance at an elevation above 4500 feet
(in Canada), check with local authorities.
WARNING
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
NOTE: This installation must conform with local codes. In the
absence of local codes you must comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A.
and the CAN/CGA B149 Installation Codes in Canada.
4
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750oC, shall be considered
non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper,
plant fibers, plastics, or other material that can ignite and
burn, whether flame proofed or not, or whether plastered or
unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
5
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, including but not limited to decks and porches, the following
requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) inch in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.
6
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
2
Getting Started
A. Design and Installation Considerations
C. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
WARNING
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult local building, fire officials or authorities having
jurisdiction about restrictions, installation inspection, and
permits.
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
• Electrical wiring.
• Carefully remove the appliance and components from
the packaging.
• The vent system components and trim doors are shipped
in separate packages.
• The gas logs may be packaged separately and must be
field installed.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
WARNING
WARNING
Keep appliance dry.
• Mold or rust may cause odors.
• Water may damage controls.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
B. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
Reciprocating saw
Framing material
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Pliers
Hi temp caulking material
Any such action may cause a fire hazard.
Hammer
Gloves
Phillips screwdriver
Framing square
Flat blade screwdriver
Electric drill and bits (1/4 in.)
Plumb line
Safety glasses
Level
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
Manometer
Voltmeter
Tape measure
Noncorrosive leak check solution
One 1/4 inch female connection (for optional fan).
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
7
3
Framing and Clearances
NOTE:
• Illustrations reflect typical installations and are FOR DESIGN
PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
WARNING
Fire Risk
Provide adequate clearance:
• Around air openings
• To combustibles
• For service access
Locate appliance away from traffic areas.
A. Selecting Appliance Location
NOTE: For actual appliance dimensions refer to Section 16.
When selecting a location for your appliance it is important to
consider the required clearances to walls (see Figure 3.1).
A
N
E
L
F
D
F
A
A
C
C
In addition to these framing dimensions, also reference the following sections:
• Clearances and Mantel Projections (Section 3.C and 3.E)
• Vent Clearances and Framing (Section 6).
K
H
B
J
G
I
G
J
M
Models
SL-550TR-IPI-E
SL-550TR-E
A
B
C
D
E
Min.
F
Min.
G
H
I
J
K
L
M
N
in.
42
37
59-1/2
1
1/2
44
62-1/4
16-1/4
48-1/2
68-3/4
15-1/16
7-1/2
7-1/8
mm
1067
940
1511
25
13
1118
1581
413
1232
1746
383
191
181
1
1/2
45-1/2
64-3/8
16-1/4
48-1/2
68-3/4
16-5/8
7-1/2
9
25
13
1156
1635
413
1232
1746
422
191
229
See Section
E for Alcove
Installation
SL-750TR-IPI-E
SL-750TR-E
in.
45-1/2
42
64-3/8
mm
1156
1067
1635
SL-950TR-IPI-E
SL-950TR-E
in.
50-1/2
49
71-1/2
1
1/2
50-1/2
71-1/2
16-1/4
50-1/2
71-1/2
19-1/2
9-1/4
11-5/8
mm
1283
1245
1816
25
13
1283
1816
413
1283
1816
495
235
295
Figure 3.1 Appliance Locations
8
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
Gas line holes and other openings should be caulked with
high temp caulk or stuffed with unfaced insulation. If the
appliance is being installed on a cement slab, a layer of
plywood may be placed underneath to prevent conducting
cold up into the room.
B. Constructing the Appliance Chase
A chase is a vertical boxlike structure built to enclose the
gas appliance and/or its vent system. Vertical vents that run
on the outside of a building may be, but are not required
to be, installed inside a chase.
C. Clearances
Construction of the chase may vary with the type of building.
These instructions are not substitutes for the requirements
of local building codes. Local building codes MUST be
checked.
WARNING
Fire Risk.
Odor Risk.
• Install appliance on hard metal or wood surfaces
extending full width and depth of appliance.
• Do NOT install appliance directly on carpeting,
vinyl, tile or any combustible material other than
wood.
Chases should be constructed in the manner of all outside
walls of the home to prevent cold air drafting problems.
The chase should not break the outside building envelope
in any manner.
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
WARNING
Fire Risk.
• Construct chase to all clearance specifications
in manual.
• Locate and install appliance to all clearance
specifications in manual
To further prevent drafts, the wall shield and ceiling firestops
should be caulked with high temperature caulk to seal gaps.
A
MEASURE FROM TOP OF UNIT
OPENING OR FROM TOP OF HOOD
E
F
H
B
J
C
G
I
D
A
B
DVP Pipe SLP Pipe
Models
SL-550TR-E
SL-750TR-E
SL-950TR-E
in.
mm
in.
mm
in.
mm
Rough
Opening
(Width)
Rough
Opening
(Width)
10
254
10
254
10
254
8-5/8
219
8-5/8
219
8-5/8
219
MINIMUM FRAMING DIMENSIONS*
C
D
E
F
G
H
I
J
**DVP Pipe SLP Pipe
Rough
Opening
(Height)
34-3/4
883
38-1/4
971
42 1/4
1073
Rough
Opening
(Depth)
Rough
Opening
(Depth)
16-1/4
413
16-1/4
413
16-1/4
413
16-1/4
413
16-1/4
413
16-1/4
413
Rough
Clearance Combustible Combustible Behind
Sides of
Front of
Opening
to Ceiling
Floor
Flooring
Appliance Appliance Appliance
(Width)
37
940
42
1067
49
1245
32
813
32
813
32
813
0
0
0
0
0
0
0
0
0
0
0
0
1/2
13
1/2
13
1/2
13
1/2
13
1/2
13
1/2
13
36
915
36
915
36
914
* Adjust framing dimensions for interior sheathing (such as sheetrock)
C** Add 12 inches for rear venting with one 90° elbow.
Figure 3.2 Clearances to Combustibles
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
9
D. Elevated Hearth Systems
Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various dimensions.
Some hearth systems will elevate the appliance off the floor at a given dimension. For example, if appliance will be used with a
Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 inches. The 9-1/4 inch elevation will also have to be added to the
following: Extension Wall Hole referenced in Figure 6.3 (Exterior Wall Hole) and Rough Opening Height (header height) referenced in
Figure 3.2. NOTE: Finished floor thickness should also be considered when determining installation dimensions.
MODEL
SL-550
SL-750
SL-950
DESCRIPTION
ELEVATED APPLIANCE
DIMENSION
See Note 1
0
9-1/4 in.
0
9-1/4 in.
0 (See Note 3)
9 1/4 in.
1-1/2 in.
0
1-3/4 in.
0
MARBLE LEG CUT
LENGTH
See Note 2
29-3/8 in.
29-3/8 in.
29-3/8 in.
29-3/8 in.
27-3/8 in.
29-3/8 in.
N/A
N/A
N/A
N/A
CAMM550PGH
1-3/4 in.
N/A
ESSEX550PG
ESSEX550PGH
ESSEXM550PG
0
1-3/4 in.
0
N/A
N/A
N/A
ESSEXM550PGH
1-3/4 in.
N/A
LUNA-32-GY
MON550PG
MON550PGH
MONM550PG
1-1/6 in.
0
1-3/4 in.
0
N/A
N/A
N/A
N/A
MONM550PGH
1-3/4 in.
N/A
0
9-1/4 in.
0
9-1/4 in.
0 (See Note 3)
9-1/4 in.
1-1/2 in.
0
1-3/4 in.
0
32-7/8 in.
32-7/8 in.
32-7/8 in.
32-7/8 in.
27-3/8 in.
29-3/8 in.
N/A
N/A
N/A
N/A
CAMM36PGH
1-3/4 in.
N/A
ESSEX36PG
ESSEX36PGH
ESSEXM36PG
0
1-3/4 in.
0
N/A
N/A
N/A
ESSEXM36PGH
1-3/4 in.
N/A
LUNA-36-GY
MON36PG
MON36PGH
MONM36PG
1-1/16 in.
0
1-3/4 in.
0
N/A
N/A
N/A
N/A
MONM36PGH
1-3/4 in.
N/A
0 (See Note 3)
9-1/4 in.
1-1/2 in.
32-7/8 in.
32-7/8 in.
N/A
PART #
KENWOOD CABINET
KENWOOD CABINET W/ BASE
KENWOOD CORNER CABINET
KENWOOD CORNER CABINET W/ BASE
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
LAURENT SURROUND
CAMDEN SURROUND
CAMDEN SURROUND W/HEARTH
CAMDEN SURROUND W/MANTEL
CAMDEN SURROUND W/MANTEL &
HEARTH
ESSEX SURROUND
ESSEX SURROUND W/HEARTH
ESSEX SURROUND W/MANTEL
ESSEX SURROUND W/MANTEL &
HEARTH
LUNA SURROUND
MONROE SURROUND
MONROE SURROUND W/HEARTH
MONROE SURROUND W/MANTEL
MONROE SURROUND W/MANTEL &
HEARTH
KENWOOD CABINET
KENWOOD CABINET W/ BASE
KENWOOD CORNER CABINET
KENWOOD CORNER CABINET W/ BASE
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
LAURENT SURROUND
CAMDEN SURROUND
CAMDEN SURROUND W/HEARTH
CAMDEN SURROUND W/MANTEL
CAMDEN SURROUND W/MANTEL &
HEARTH
ESSEX SURROUND
ESSEX SURROUND W/HEARTH
ESSEX SURROUND W/MANTEL
ESSEX SURROUND W/MANTEL &
HEARTH
LUNA SURROUND
MONROE SURROUND
MONROE SURROUND W/HEARTH
MONROE SURROUND W/MANTEL
MONROE SURROUND W/MANTEL &
HEARTH
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
LAURENT SURROUND
KDC44SBP
KDC44SBP W/ HTKDC44SBP
KDA44SBP
KDA44SBP W/ HTKDA44SBP
AFKDMPA
AFKDMPA W/ HTKDMPA
LAURENT-32
CAM550PG
CAM550PGH
CAMM550PG
KDC48DBP
KDC48DBP W/ HTKDC48DBP
KDA48SBP
KDA48SBP W/ HTKDA48SBP
AFKDMPB
AFKDMPB W/ HTKDMPB
LAURENT-36
CAM36PG
CAM36PGH
CAMM36PG
AFKDMPC
AFKDMPC W/ HTKDMPC
LAURENT-42
NOTE 1. Add dimensions to Exterior Wall Hole (Figure 6.2) and Rough Opening Height (Figure 3.2).
NOTE 2. Verify Marble Cut Lengths on site prior to cutting.
NOTE 3. Dimensions assume use of a 3/4 in. Hearth Pad.
10
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
E. Mantel Projections
All measurements are in inches.
CEILING
12
1/2 IN.
MINIMUM
11
10
9
8
32
7
6
5
4
3
4
5
6
7
8
9
10
11
12
2-7/8 IN.
MINIMUM
13
3 FT. MAXIMUM
Note: Clearance from opening
to perpendicular wall.
Figure 3.5 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
TOP OF HOOD OR FIREPLACE OPENING
Figure 3.3 Clearances to mantels or other combustibles
above appliance
3 IN.
MINIMUM
1/2 in. SHEETROCK
OR COMBUSTIBLE
MATERIAL
3-1/2 in.
5-3/8 IN.
MINIMUM
UNLIMITED
Note: Clearance from opening
to perpendicular wall.
Figure 3.6 Wall Projection (Acceptable on one side of opening.)
1/2 in.
1/2 in.
SHEETROCK
3-1/2 in.
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
1/2 in.
NON-COMBUSTIBLE ZONE
Figure 3.4
Non-Combustible Zone
Models: SL-550TR-E, SL-750TR-E
SL-550TR-IPI-E, SL-750TR-IPI-E
NON-COMBUSTIBLE ZONE
Figure 3.7 Non-Combustible Zone
Models: SL-950TR-E, SL-950TR-IPI-E
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
11
4
Termination Locations
A. Vent Termination Minimum Clearances
HORIZONTAL
OVERHANG
WARNING
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Fire Risk.
Explosion Risk.
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
• Combustible materials blocking cap may
ignite.
• Restricted air flow affects burner operation.
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
WARNING
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as
specified.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
Measure vertical clearances from this surface.
* 3 foot minimum in snow regions
Figure 4.2 Minimum Height from Roof to Lowest Discharge
Opening
Figure 4.2 specifies minimum vent heights for various
pitched roofs.
GAS, WOOD OR FUEL
OIL TERMINATION
C
B
GAS
TERMINATION
A
Measure horizontal clearances from this surface.
(See Figure 4.4 for specific clearances)
Figure 4.1
Gas
Termination
Wood & Fuel Oil
Termination
Comments
A
6 in.
20 in. min.
Horizontal distance between terminations
B
20 in.
24 in. min.
Distance to perpendicular wall
C
18 in.
18 in.
Vertical distance between terminations
Figure 4.3 Multiple Vertical Termination
12
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
M
N
P
R
Q
(See Note 2)
V
T
V
S
Electrical
Service
S
V
D*
V
V = VENT TERMINAL
A
B
D*
X = AIR SUPPLY INLET
= 12 inches ...............clearances above grade, veranda,
porch, deck or balcony
(See Note 1)
= 12 inches ...............clearances to window or door
that may be opened, or to permanently closed window. (Glass)
= 18 inches ...............vertical clearance to unventilated
soffit or to ventilated soffit located
above the terminal
*30 inches ..............for vinyl clad soffits and below
electrical service
F
= 9 inches ................clearance to outside corner
G
= 6 inches .................clearance to inside corner
H
I
J
K
= 3 ft. (Canada) ........not to be installed above a gas
meter/regulator assembly within 3
feet (90 cm) horizontally from the
center-line of the regulator
= 3 ft. .......................clearance to gas service regulator
vent outlet
= 9 inches (U.S.A.)
12 inches (Canada) clearance to non-mechanical
air supply inlet to building or the
combustion air inlet to any other
appliance
= 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (powered) air supply inlet
** a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings.
*** only permitted if veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the floor, or meets Note 2.
NOTE 1: On private property where termination is less than 7 feet above
a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap
shield is suggested. (See vents components page)
NOTE 2: Termination in an alcove space (spaces open only on one side
and with an overhang) are permitted with the dimensions specified for
vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be a
minimum of 1 foot below the termination cap.
Figure 4.4 Minimum Clearances for Termination
= AREA WHERE TERMINAL IS NOT PERMITTED
L** = 7 ft. ..........................c l e a r a n c e a b o v e p a v e d
sidewalk or a paved driveway
located on public property
M*** = 18 inches.................clearance under veranda, porch,
(See Note 1)
deck, balcony or overhang
42 inches ................vinyl
S = 6 inches ...................clearance from sides of elec(See Note 5)
trical service
T = 12 inches ..................clearance above electrical
(See Note 5)
service
Alcove Applications
N
P
= 6 inches ..................non-vinyl sidewalls
12 inches ................vinyl sidewalls
= 8 ft.
1 cap
2 caps
3 caps
4 caps
QMIN = # termination caps x 3
QMIN
3 feet
6 feet
9 feet
12 feet
RMAX
2 x Q ACTUAL
1 x Q ACTUAL
2/3 x Q ACTUAL
1/2 x Q ACTUAL
RMAX = (2 / # termination caps) x QACTUAL
NOTE 3: Local codes or regulations may require different
clearances.
NOTE 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
NOTE 5: Location of the vent termination must not interfere with
access to the electrical service.
WARNING: In the U.S: Vent system termination is NOT permitted in
screened porches. You must follow side wall, overhang and ground
clearances as stated in the instructions.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas with
two or more sides open. You must follow all side walls, overhang
and ground clearances as stated in the instructions.
Hearth & Home Technologies assumes no responsibility for the
improper performance of the appliance when the venting system
does not meet these requirements.
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
13
5
Vent Information and Diagrams
A. Vent Table Key
The abbreviations listed in this vent table key are used in
the vent diagrams.
Description
V2
Second section of vertical length
H1
First section (closest to appliance) of horizontal length
H2
Second section of horizontal length
Vertica l
8-1/2 in.
WARNING
Fire Hazard.
Explosion Risk.
Asphyxiation Risk.
Do NOT connect this gas appliance to a chimney
flue serving a separate solid-fuel or gas burning
appliance.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
May impair safe operation of this appliance or
other appliances connected to the flue.
8-1/2 in.
First section (closest to appliance) of vertical length
12
V1
in
.
Symbol
Horizontal
Figure 5.1
C. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
1. Pipe measurements are shown using the effective length
of pipe (see Figure 5.2).
2. Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see
Figure 4.1).
B. Use of Elbows
CAUTION
3. Vertical terminations are measured to bottom of termination cap.
4. Horizontal pipe installed level with no rise.
ALL vent configuration specifications MUST be followed.
• This product is tested and listed to these specifications.
• Appliance performance will suffer if specifications are
not followed.
Pipe
Diagonal runs have both vertical and horizontal vent
aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 5.1).
Effective
Height/Length
Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 inches
horizontal run and 8-1/2 inches vertical run. A length of
straight pipe is allowed between two 45º elbows (see
Figure 5.1).
Millimeters
DVP4
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
DVP12MI 3 to 12
76 to 305
DVP24MI 3 to 24
76 to 610
Figure 5.2 DVP Pipe Effective Length
14
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
Effective Length
Inches
D. Use of Flex Vent
The flex vent must be supported with
the spacing between support intervals
not exceeding 4 feet, with no more
than 1/2 inch sag between supports.
A support is required at each change
in venting direction, and in any location
where it is necessary to maintain the
necessary clearance to combustibles.
A simple “up and out” installation (Figure 5.3) requires only enough support
to maintain the necessary clearance
to combustibles. However, the vent attachment point and the firestop location are considered to be supports.
3 in . C L E A R A N C E
T E R M IN AT IO N
CAP
F L E X -V E N T
1 in .
CLEAR AN CE
Figure 5.3
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
15
E. Vent Diagrams
WARNING
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling firestops.
• ALWAYS maintain specified clearances around venting and firestop systems.
• Install wall shield and ceiling firestops as specified.
Failure to keep insulation or other material away from vent pipe may cause fire.
Top Vent - Horizontal Termination
Venting with 1 elbow
H1 Maximum
V Minimum
SL-550TR-E
90 Elbow
SL-750TR-E
2 ft.
610 mm
2 ft.
610 mm
1 ft.
305 mm
152 mm
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
1-1/2 ft. 457 mm
3 ft.
914 mm
3 ft.
914 mm
3 ft.
914 mm
2-1/2 ft. 762 mm
5 ft.
1.5 m
5 ft.
1.5 m
5 ft.
1.5 m
3-1/2 ft.
1.1 m
7 ft.
2.1 m
7 ft.
2.1 m
7 ft.
2.1 m
4-1/2 ft.
1.4 m
14 ft.
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
1/2 ft.
Note: Use SLP Series
components only.
SL-950TR-E
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
H MAX. =14 ft. (4.3 m)
V + H MAX. = 40 ft. (12.2 m)
V1
H1
WARNING
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZC-SS
termination caps on top vented fireplaces, a one
foot minimum vertical vent section is required before
installing first elbow.
• When using DVP-TB1 termination cap on top vented fireplaces,
a three foot minimum vertical vent section is required before
installing first elbow.
Figure 5.4
16
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
Top Vent - Horizontal Termination
Venting with 2 elbows
H1 + H2 Maximum
V Minimum
SL-550TR-E
90 Elbow
SL-750TR-E
1/2 ft. 152 mm 1/2 ft. 152 mm
SL-950TR-E
0 ft.
0 mm
1/2 ft.
152 mm
1 ft.
305 mm
1 ft.
305 mm
1 ft.
305 mm
1-1/2 ft.
457 mm
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
2-1/2 ft.
762 mm
4 ft.
1.2 m
4 ft.
1.2 m
4 ft.
1.2 m
3-1/2 ft.
1.1 m
6 ft.
1.8 m
6 ft.
1.8 m
6 ft.
1.8 m
4-1/2 ft.
1.4 m
14 ft.
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
H + H1 MAX. =14 ft. (4.3 m)
V + H + H1 MAX. = 40 ft. (12.2 m)
V1
H2
H1
INSTALLED
HORIZONTALLY
WARNING
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZC-SS
termination caps on top vented fireplaces, a one
foot minimum vertical vent section is required before
installing first elbow.
• When using DVP-TB1 termination cap on top vented fireplaces,
a three foot minimum vertical vent section is required before
installing first elbow.
Figure 5.5
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
17
Top Vent - Horizontal Termination
Venting with 3 elbows
V1 Minimum
90 Elbow
H1 + H2 Maximum
SL-550TR-E
SL-750TR-E
SL-950TR-E
V2
V1 + V2 Min.
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
*
*
6 ft.
1.8 m
6 ft.
1.8 m
6 ft.
1.8 m
*
*
1-1/2 ft.
457 mm 10 ft.
3.0 m
10 ft.
3.0 m
10 ft.
3.0 m
*
*
2-1/2 ft.
762 mm 12 ft.
3.7 m
12 ft.
3.7 m
12 ft.
3.7 m
*
*
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
*
*
1/2 ft.
3-1/2 ft.
152 mm
1.1 m
14 ft.
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
H1 + H2 MAX. =14 ft. (4.6 m)
V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
*No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)
H2
V2
H1
WARNING
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZCSS termination caps on top vented fireplaces,
a one foot minimum vertical vent section is
required before installing first elbow.
Figure 5.6
18
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
V1
Top Vent - Vertical Termination
No Elbows
V1 = 60 ft. Max. (18.3 m)
Note: If installing a vertical vent/termination off the top of
the appliance, the optional vertical termination baffle may
be needed.
Exhaust restrictor Instructions
1. Install the exhaust restrictor over the center of the exhaust outlet in the firebox (see Figure 5.8).
2. Center the exhaust restrictor in the open end of the
exhaust outlet and secure through the slots on the exhaust restrictor with the 2-1/4 in. self tapping screws
provided in the appliance manual bag.
To access the exhaust
openings, remove the exhaust baffle. To remove
exhaust baffle, remove
the two wing nuts.
Note: Use SLP Series
components only.
EXHAUST BAFFLE
Top Vent Application
Exhaust restrictor
V1
Rear Vent Application
Exhaust restrictor
Note: Be sure to reinstall the exhaust baffle
after exhaust restrictor
installation.
Figure 5.7
Exhaust restrictors are recommended for these vertically
terminated products which have excessive draft. Exhaust
restrictors will compensate for high draft, and restore visual flame height. If the vent configuration has a total
vertical of 15-60 feet, an exhaust restrictor may be needed. The exhaust restrictor can be located in the appliance
manual bag.
Figure 5.8
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
19
Top Vent - Vertical Termination
Venting with 2 elbows
SL-550TR-E
V1 MIN.
SL-750TR-E
H MAX.
90 Elbow
H MAX.
SL-950TR-E
V2
V1 + V2 MIN.
1-1/2 ft.
457 mm
1-1/2 ft.
457 mm
1 ft.
H MAX.
305 mm
*
*
1/2 ft.
152 mm
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
*
*
1-1/2 ft.
457 mm
3 ft.
914 mm
3 ft.
914 mm
3 ft.
914 mm
*
*
2-1/2 ft.
762 mm
5 ft.
1.5 m
5 ft.
1.5 m
5 ft.
1.5 m
*
*
3-1/2 ft.
1.1 m
7 ft.
2.1 m
7 ft.
2.1 m
7 ft.
2.1 m
*
*
4-1/2 ft.
1.4 m
15 ft.
4.6 m
15 ft.
4.6 m
15 ft.
4.6 m
*
*
H MAX. =15 ft. (4.6 m)
V1 + V2 + H MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
V2
H1
Figure 5.9
20
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
V1
Top Vent - Vertical Termination
Venting with 3 elbows
V1 MIN.
90 Elbow
1/2 ft.
SL-550TR-E
SL-750TR-E
SL-950TR-E
H MAX.
H MAX.
H MAX.
1/2 ft.
152 mm
1/2 ft.
152 mm
0 ft.
0 mm
V2
V1 + V2 MIN.
*
*
152 mm
1 ft.
305 mm
1 ft.
305 mm
1 ft.
305 mm
*
*
1-1/2 ft. 457 mm
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
*
*
2-1/2 ft. 762 mm
4 ft.
1.2 m
4 ft.
1.2 m
4 ft.
1.2 m
*
*
3-1/2 ft.
1.1 m
6 ft.
1.8 m
6 ft.
1.8 m
6 ft.
1.8 m
*
*
4-1/2 ft.
1.4 m
14 ft.
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
*
*
H MAX. =14 ft. (4.6 m)
V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
V2
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 5.10
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
21
Top Vent - Vertical Termination
Venting with 4 elbows
V1 MIN.
Note: Use SLP Series
components only.
1-1/2 ft.
H1 MAX.
457 mm
4 ft.
1.2 m
V2 MIN.
4 ft.
1.2 m
H2 MAX.
4 ft.
1.2 m
V1 + V2 + V3 + H1 + H2 Maximum= 40 ft. (12.2 m)
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
V3
V2
H2
H1
V1
Figure 5.11
22
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
V3 MIN.
3-1/2 ft.
1.0 m
Rear Vent - Horizontal Termination
No Elbows
CAUTION
*For SL-950TR-E ONLY:
H1 Maximum can be up to 24 inches ONLY if the Optional
Refractory Kit (BRICK-950-E) is NOT used.
Note: Use DVP Series
components only.
H1 MAX
SL-550TR-E
24 in.
610 mm
SL-750TR-E
24 in.
610 mm
SL-950TR-E
18 in.*
457 mm
Figure 5.12
Rear Vent - Horizontal Termination
One 45º Elbow
H1 = 9 in. (229 mm) Maximum
For corner installation of models SL-550TR-E and SL-750TR-E ONLY
Note: Use DVP Series
components only.
Note: Do not use a 45º elbow
for SL-950TR-E. Use two 90º
elbows for corner installation on
SL-950TR-E
Figure 5.13
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
23
Rear Vent - Horizontal Termination
Venting with 2 elbows
Note: Use DVP Series
components only.
H1 MAX.
V1 MIN.
H2 MAX.
1-1/2 ft. 457 mm
Back to back elbows
H1 + H2 MAX.
1 ft.
305 mm
2-1/2 ft.
762 mm
3 ft.
914 mm
1 ft.
305 mm
3 ft.
914 mm
6 ft.
1.8 m
5 ft.
1.5 m
3 ft.
914 mm
5 ft.
1.5 m
10 ft.
3.0 m
7 ft.
2.1 m
5 ft.
1.5 m
7 ft.
2.1 m
14 ft.
4.3 m
H1 MAX. = 7 ft. (2.1 m)
H1 + H2 MAX. = 14 ft. (4.3 m)
V1 + H1 + H2 MAX. = 40 ft. (12.2 m)
Figure 5.14
Rear Vent - Horizontal Termination
Venting with 3 elbows
Note: Use DVP Series
components only.
H1 MAX.
INS TALLE D
HORIZON TAL LY
V1 MIN.
1-1/2 ft.
457 mm
Back to back elbows
3-1/2 ft.
1.1 m
1 ft.
5-1/2 ft.
1.7 m
2 ft.
7-1/2 ft.
2.3 m
3 ft.
H2 + H3 MAX.
1 ft.
305 mm
2-1/2 ft.
762 mm
305 mm
2 ft.
610 mm
5-1/2 ft.
1.7 m
610 mm
4 ft.
1.2 m
9-1/2ft.
2.9 m
914 mm
6 ft.
1.8 m
13-1/2 ft.
4.1 m
H1 MAX. = 7-1/2 ft. (2.3 m)
H1 + H2+ H3 MAX. = 13-1/2 ft. (4.1 m)
V1 + H1 + H2+ H3 MAX. = 40 ft. (12.2 m)
Figure 5.15
24
H1 + H2+ H3 MAX.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
Rear Vent - Vertical Termination
Venting with 1 elbow
Note: Use DVP Series
components only.
V1 MIN.
H1 MAX.
1 ft.
305 mm
3-1/2 ft.
1.1 m
2 ft.
610 mm
5-1/2 ft.
1.7 m
3 ft.
914 mm
7-1/2 ft.
2.3 m
H MAX. = 7-1/2 ft. (2.3 m)
V1 + H1 MAX. = 40 ft. (12.2 m)
V1
H1
Figure 5.16
Note: Use DVP Series
components only.
Rear Vent - Vertical Termination
Venting with 2 elbows
H1 + H2 MAX
Back to back elbows
V1
V1 MIN.
1/2 ft.
152 mm
2-1/2 ft.
762 mm
1 ft.
305 mm
4-1/2 ft.
1.4 m
2 ft.
610 mm
6-1/2 ft.
2.0 m
3 ft.
914 mm
H MAX. = 6-1/2 ft. (2 m)
V + H+ H1 MAX. = 40 ft. (12.2 m)
IN S TA L L E D
H O R IZ O N TA L LY
H1
H2
Figure 5.17
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
25
Rear Vent - Vertical Termination
Venting with 3 elbows
V1 MIN.
H1 MAX.
Back to back elbows
H2 MAX.
H1 + H2 MAX.
1-1/2 ft.
457 mm
1 ft.
305 mm
2-1/2 ft.
762 mm
1 ft.
305 mm
3-1/2 ft.
1.1 m
3 ft.
914 mm
6-1/2 ft.
2.0 m
2 ft.
610 mm
5-1/2 ft.
1.7 m
5 ft.
1.5 m
10-1/2 ft.
3.2 m
3 ft.
914 mm
7-1/2 ft.
2.3 m
7 ft.
2.1 m
14-1/2 ft.
4.4 m
H1 MAX. = 7-1/2 ft. (2.3 m)
H1 + H2 MAX. = 14-1/2 ft. (4.4 m)
V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
Note: Use DVP Series
components only.
V2
H2
V1
Figure 5.18
26
H1
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
6
Vent Clearances and Framing
A. Pipe Clearances to Combustibles
WARNING
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as
specified.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
• DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
• If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
• SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed.
If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.
(DVP-SLP Pipe Shown)
3 in. (76 mm)
top clearance
Heat
Shield
3 in. (76 mm)
top clearance *
Heat
Shield
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
WALL
3 in. (76 mm)
top clearance *
Heat
Shield
Heat
Shield
Wall
Shield
Firestop
1 in. (25 mm)
clearance
bottom & sides
WALL
* When using SLP pipe, minimum clearances from the vent pipe to combustible materials at inside wall firestops are:
Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
Figure 6.1 Horizontal Venting Clearances To Combustible
Materials
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
27
B. Wall Penetration Framing
Combustible Wall Penetration
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
10 in.
10 in.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 1-1/2 in. (38 mm)
overlap of attached heat shields must be maintained.
10 in.
12 in.
• DVP pipe - A wall shield firestop is required on one side
only on interior walls. If your local inspector requires a
wall shield firestop on both sides, then both wall shield
firestops must have a heat shield (refer to Section 16.B.)
attached to them.
• See Section 8.M. for information for regarding the installation of a horizontal termination cap.
A*
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
SL-550TR-E
SL-750TR-E
SL-950TR-E
A*
B*
C
D
in.
36 1/2
24 3/8
35 1/2
23 3/8
mm
927
619
902
594
26 7/8
in.
41
27 7/8
40
mm
1041
708
1016
683
in.
44
31 7/8
43
30 7/8
mm
1118
810
1092
784
* Shows center of vent framing hole for top or rear venting.
The center of the hole is one (1) inch (25.4 mm) above the
center of the horizontal vent pipe.
Figure 6.2 Exterior Wall Hole
28
D
B*
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter
one in. greater than the pipe is acceptable.
C
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
C. Install the Ceiling Firestop
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/fl oor (see
Figure 6.3).
ATTIC ABOVE
• SLP pipe only - Frame opening 9 in. x 9
in. (229 mm x 229 mm) whenever the vent
penetrates a ceiling/floor (see Figure 6.3).
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
A
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 6.4.
• Secure with three fasteners on each side.
A
WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
PIPE
A
DVP
10 in. (254 mm)
SLP
9 in. (229 mm)
Figure 6.3 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE
CEILING FIRESTOP
INSTALLED BELOW CEILING
CEILING FIRESTOP
INSTALLED ABOVE CEILING
Figure 6.4 Installing the Attic Shield
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
29
D. Install Attic Insulation Shield
WARNING! Fire Risk. DO NOT allow loose materials or
insulation to touch vent. Hearth & Home Technologies
Inc. requires the use of an attic shield.
BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE
The National Fuel Gas Code ANSI Z223.1 and NFPA 54
requires an attic shield constructed of 26 gauge minimum
metal that extends at least 2 in. (51 mm) above insulation.
Attic shields must meet specified clearance and be secured in place.
Flat Ceiling Installation
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
INSERT 3
SCREWS
BEND 3 TABS
OUTWARD TO
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
CLEARANCE
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
Figure 6.5 Attic Insulation Shield
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Vaulted Ceiling Installation
• The attic insulation shield has been laser-etched with cut
lines and ceiling pitches to make field trimming easier.
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Cut the attic insulation shield (if application is for vaulted
ceiling) using a laser-etched cut line, to fit your ceiling
pitch. Snip cut edge to recreate 1 in. bend tabs all the
way around the bottom.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
30
LASER-ETCHED
CUT LINES
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
7
Appliance Preparation
WARNING
Fire Risk
Once appliance is setup for top or rear venting, it
CANNOT be changed at a later time.
If vent cap and components previously removed
are improperly reinstalled, a fire may result.
A. Top Vent
CAUTION
Sharp Edges
• Wear protective gloves and safety
glasses during installation.
2 SCREWS
Figure 7.3 Replace the two screws as shown.
Note: Actual unit may look different than the fireplace shown
in this section.
2 SCREWS
Figure 7.1 For top vent, remove the two screws holding the
top heat shield in place. For rear vent, see Section 7B.
WARNING
Fire Risk
Do not remove heat shield.
Elevated header temperatures may cause a fire.
Figure 7.2 Rotate the top heat shield to the vertical
position as shown above. The heat shield must remain in
the vertical position.
Figure 7.4 Remove the vent cap.
Figure 7.5 Remove the insulation basket and white insulation from the center vent pipe.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
31
Figure 7.9 Cut the metal retaining band and fold the
sides out.
Figure 7.6 Remove the insulation from the outer vent pipe.
Figure 7.10 Fold the center parts of the retaining band
out and use to remove the vent cap.
2 SCREWS
Figure 7.7 To attach the first section of vent pipe, make
sure to use the fiberglass gasket to seal between the first
vent component and the outer fireplace wrap. Use 2 self
tapping screws to secure the gasket to the outer wrap.
Note: Once the vent cap has been removed, it cannot be
reattached.
Figure 7.11 Discard the vent cap, remove and discard
the insulation basket. Note: Once the vent cap has been
removed it CANNOT be reattached.
B. Rear Vent
Figure 7.8 Fold the tabs toward the center of the fire plug
(90°) and remove the insulation gasket.
32
Figure 7.12 Attach the first vent section (it will snap into
place). Slide the insulation gasket onto the vent section,
up against the appliance and over the tabs. Use two selftapping screws to secure gasket to outer wrap.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
C. Securing and Leveling the Appliance
WARNING
Fire Risk.
• Prevent contact with sagging, loose insulation.
• Do NOT install against combustible materials
such as exposed insulation, plastic and insulation
backer.
The diagram shows how to properly position, level, and
secure the appliance (see Figure 7.11). Nailing tabs are provided to secure the appliance to the framing members.
• Venting - refer to Vent Clearances and Framing (Section
6.B) for hole location.
• Place the appliance into position.
NAILING TABS
BOTH SIDES
• Level the appliance from side to side and front to
back.
• Shim the appliance, as necessary. It is acceptable to
use wood shims.
• Bend out nailing tabs on each side.
• Keep nailing tabs flush with the framing.
Figure 7.13 Proper Positioning, Leveling and Securing of an
Appliance
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
WARNING
Fire Risk.
• ALWAYS maintain specified
clearances around the appliance.
• Do NOT notch into the framing around the appliance spacers.
Failure to keep insulation, framing or other material away from
the appliance may cause fire.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
33
8
Installing Vent Pipe (DVP and SLP Pipe)
A. Assemble Vent Sections (DVP Pipe Only)
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face
toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end to the starting collar
• Inner pipe over inner collar
• Push the pipe section until all lanced tabs snap in place
• Lightly tug on pipe to confirm it has locked.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
All outer pipe joints must be sealed with high temperature
silicone, including the slip section that connects directly to
the horizontal termination cap.
Figure 8.1 High Temperature Silicone Sealant
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 8.1
A
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Assemble Pipe Sections (DVP Pipe Only)
Per Figure 8.2:
Lances
B
Figure 8.3
Figure 8.2
Note: Make sure that the seams are not aligned to prevent
unintentional disconnection.
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
CORRECT
For 90° and 45° elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2 in.
(13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
Figure 8.4 Seams
34
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
INCORRECT
B. Assemble Vent Sections (SLP Pipe Only)
C. Assemble Slip Sections
To attach the first vent component to the starting collars
of the appliance:
• Slide the inner flue of the slip section into the inner flue
of the pipe section and the outer flue of the slip section
over the outer flue of the pipe section. See Figure 8.6.
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Slide together to the desired length.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 8.5.
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration.
High temperature caulk may be used to hold the part in
place.
• Continue adding vent components, locking each
succeeding component into place.
Pilot hole
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
Figure 8.6 Slip Section Pilot Holes
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with high temperature silicone,
including the slip section that connects directly to the horizontal termination cap.
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 8.6.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 8.1
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Figure 8.7 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed using
a high temperature silicone sealant.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
Figure 8.5 Adding Venting Components
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sealed.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
35
D. Secure the Vent Sections
E. Disassemble Vent Sections
• Vertical runs of DVP pipe must be supported every 8 ft.
(2.44 m) after the 25 ft. (7.62 m) maximum unsupported
rise.
• Rotate either section (see Figure 8.10) so the seams
on both pipe sections are aligned as shown in Figure
8.11.
• Vertical runs of SLP pipe must be supported every 8 ft.
(2.44 m).
• Pull carefully to separate the pieces of pipe.
• Horizontal sections must be supported every 5 feet
(1.52 m).
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support. See Figures 8.8 and 8.9.
• Wall shield firestops may be used to provide horizontal
support.
• SLP ceiling firestops have tabs that may be used to
provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below
connection point to appliance.
Figure 8.10 Rotate Seams for Disassembly
Figure 8.11 Align and Disassemble Vent Sections
Figure 8.8 Securing Vertical Pipe Sections
Figure 8.9 Securing Horizontal Pipe Sections
36
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
F. Install Decorative Ceiling Components
(SLP only)
LEVEL
A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
CATHEDRAL CEILING
SUPPORT BOX
• Seal the gap between the vent pipe and firestop using
high temperature silicone to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to the
ceiling and attaching it using the provided screws.
2 in. (51 mm) MIN. BELOW
FINISHED CEILING
A decorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
• Remove shingles or other roof covering as necessary to
cut the rectangular hole for the support box. Cut the hole
1/8 in. (3 mm) larger than the support box outline.
CUT HOLE 1/8 in. (3 mm)
GREATER IN SIZE THAN
PATTERN OF SUPPORT
BOX AS IT IS PROJECTED
ONTO ROOF LINE
Figure 8.12
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm) below the ceiling (Figure
8.12).
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 8.13.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
Figure 8.13
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
37
G. Install Metal Roof Flashing
Note: Skip this section if using the RF4-8.
• See minimum vent heights for various pitched roofs
(Figure 8.14) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 8.15.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Figure 8.15
H. Assemble and Install Storm Collar
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft.
Flat to 6/12........................................ 1.0*
Over 6/12 to 7/12 ............................ 1.25*
Over 7/12 to 8/12 .............................. 1.5*
Over 8/12 to 9/12 .............................. 2.0*
Over 9/12 to 10/12 ............................. 2.5
Over 10/12 to 11/12 ......................... 3.25
Over 11/12 to 12/12 ........................... 4.0
Over 12/12 to 14/12 ........................... 5.0
Over 14/12 to 16/12 ........................... 6.0
Over 16/12 to 18/12 ........................... 7.0
Over 18/12 to 20/12 ........................... 7.5
Over 20/12 to 21/12 ........................... 8.0
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
• Connect both halves of the storm collar with two screws
(see Figure 8.16).
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
is tight against the pipe section.
• Slide the assembled storm collar down the pipe section
until it rests on the roof flashing (see Figure 8.17).
• Caulk around the top of the storm collar (see Figure 8.23).
* 3 foot minimum in snow regions
Figure 8.14 Minimum Height From Roof To Lowest Discharge
Opening
Figure 8.16 Assembling the Storm Collar
NOTICE: Failure to properly caulk the roof flashing could
cause water entry.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 8.15.
Figure 8.17 Assembling the Storm Collar Around the Pipe
38
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
I. Install RF4-8
The RF4-8 may be used in place of the roof flashing and
storm collar (Sections 8.G. and 8.H.)
Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FS when using the RF4-8
Flashing. Refer to Section 8.D Securing Vent Sections.
SECURE WITH 4
SCREWS NO LONGER
THAN 1 IN. (25 MM)
Figure 8.20 Apply Sealant
SLP-FS
Figure 8.18 Secure Pipe with SLP-FS
• Trim the rubber boot (using scissors or a utility knife),
cutting along the marked measurement lines. See Figure
8.19. Use the 150 mm line for SLP, 210 mm for DVP.
• Lubricate pipe or flue with water and slide the flashing
down. It may be necessary to trim the top shingles around
the base of the rubber boot to ensure a good fit.
APPLY SEALANT
TOP & PARTIAL SIDES
• Draw around flashing, remove.
• Apply silicone sealant to roof inside the lines (Figure 8.20)
• Lubricate pipe or flue with water and slide flashing down.
Seat firmly in sealant. Nail roof flashing to the roof.
• Apply silicone sealant on the top outside of the base plate
on the sides and on top edge. See Figure 8.21. Install
shingles, Apply sealant at the top edge of the rubber
boot. See Figure 8.22.
• We recommend that you top coat with conventional
acrylic house paint to improve the appearance of your
galvanized base flashing.
Figure 8.21 Slide Flashing Down, Secure & Apply Sealant
SILICONE SEALANT
(TOP OF BOOT)
SHINGLES TRIMMED
FLASHING OVER
SHINGLES
SHINGLES OVER
FLASHING
Figure 8.22 Installation Complete
Figure 8.19 Trim Rubber Boot
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
39
J. Install Vertical Termination Cap
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of the
cap into the outer flue of the pipe (see Figure 8.23).
TERMINATION CAP
L. Heat Shield Requirements for Horizontal
Termination
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thickness.
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 8.25).
• Heat shields must overlap 1-1/2 in. (38 mm) minimum.
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 10.25.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
and wall shield firestop must to be trimmed. A minimum
1-1/2 in. (38 mm) overlap MUST be maintained.
(1 of 3)
STORM
COLLAR
SCREWS
CAULK
• Use an extended heat shield if the finished wall thickness
is greater than 7-1/4 in. (184 mm).
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
• Attach the extended heat shield to either of the existing
heat shields using the screws supplied with the extended
heat shield. Refer to vent components diagrams in the
back of this manual.
Figure 8.23
K. Install Decorative Wall Components (SLP
only)
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the firestop.
Important Notice: Heat shields may not be field constructed.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have been
connected, slide the wall thimble up to the interior wall
surface and attach with screws provided. See Figure
8.24.
Figure 8.24 Wall Thimble
40
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
M. Install Horizontal Termination Cap (DVP
and SLP Pipe)
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
Failure to maintain overlap may cause overheating and
fire.
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
HEAT SHIELD OR
EXTENDED
HEAT SHIELD
HEAT SHIELD
1-1/2 IN. (38 MM) MIN.
OVERLAP
WALL SHIELD
FIRESTOP
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
SLIP SECTION
CAN BE EXTENDED
• Flash and seal as appropriate for siding material at
outside edges of cap.
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 4 of this manual.
CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone
from touching the hot cap.
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit and
HRC caps are available. When penetrating a brick wall, a
brick extension kit is available for framing the brick.
INNER VENT
SHEATHING
OUTER VENT
INTERIOR
EXTERIOR
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
Figure 8.25 Venting through the wall
Termination Cap Specification Chart
(depth without using additional pipe sections)
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2
Top Vent
Rear Vent
Top Vent
Rear Vent
Depth
Depth
Depth
Depth
3-1/8 in. to
5-1/2 in. to
N/A
N/A
5 in.
9-1/2 in.
SL Series
DVP-HPC1
Top Vent
Depth
N/A
DVP-HPC1
Rear Vent
Depth
3-1/8 in. to
5-1/4 in.
DVP-HPC2
Top Vent
Depth
N/A
DVP-HPC2
Rear Vent
Depth
5-1/4 in. to
9-3/8 in.
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
41
9
Gas Information
A. Fuel Conversions
C. Gas Connection
Before making gas connections ensure that appliance being installed is compatible with the available gas type.
Any natural or propane gas conversions necessary to
meet the appliance and locality needs must be made by
a qualified technician using Hearth & Home Technologies
specified and approved parts.
NOTE: Have the gas supply line installed in accordance
with local building codes, if any. If not, follow ANSI
223.1. Installation should be done by a qualified installer
approved and/or licensed as required by the locality. (In
the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.)
B. Gas Pressures
Proper input pressures are required for optimum appliance performance. Gas line sizing requirements need to
be made following NFPA54.
NOTE: A listed (and Commonwealth of Massachusetts
approved) 1/2 inch (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 inch (13
mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Refer to Reference Section 16 for location of gas line
access in appliance.
NOTE: Gas line may be run from either side of the appliance
provided the hole in the outer wrap does NOT exceed 2-1/2
inches in diameter and does not penetrate the firebox.
WARNING
WARNING
Verify inlet pressures.
• High pressure may cause overfire condition.
• Low pressure may cause explosion.
• Verify minimum pressures when other
household gas appliances are operating.
Install regulator upstream of valve if line pressure
is greater than 1/2 psig.
Pressure requirements for appliance are shown in the
table below. Minimum pressures must be met when other
household gas appliances are operating.
Pressure
42
Natural Gas
Propane
Minimum
Inlet Pressure
5.0 inches
w.c.
11.0 inches
w.c.
Maximum Inlet
Gas Pressure
14.0 inches
w.c.
14.0 inches
w.c.
Manifold
Pressure
3.5 inches
w.c.
10.0 inches
w.c.
Gas Leak Risk
• Support control when attaching pipe to prevent
bending gas line.
NOTE: The gap between supply piping and gas access hole
may be caulked with high temperature caulk or stuffed with
non-combustible, unfaced insulation to prevent cold air infiltration.
• Ensure that gas line does not come in contact with outer
wrap of appliance. Follow local codes.
• Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on
the manual shutoff valve.
WARNING
Fire or Explosion Hazard
• Gas buildup during line purge may ignite.
• Purge should be performed by qualified technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as
sparks or open flames.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
• A small amount of air will be in the gas supply lines.
When first lighting appliance it will take a short time for
air to purge from lines. When purging is complete the
appliance will light and operate normally.
WARNING
CHECK FOR GAS LEAKS
Explosion Risk
Fire Risk
Asphyxiation Risk
• Check all fittings and connections.
• Do not use open flame.
• After the gas line installation is complete, all
connections must be tightened and checked
for leaks with a commercially-available,
non-corrosive leak check solution. Be sure
to rinse off all leak check solution following
testing.
Fittings and connections may have
loosened during shipping and handling.
HIGH ALTITUDE INSTALLATIONS
U.L. Listed gas appliances are tested and approved
without requiring changes for elevations from 0 to
2000 feet in the U.S.A. and Canada.
When installing this appliance at an elevation above
2000 feet, it may be necessary to decrease the
input rating by changing the existing burner orifice
to a smaller size. Input rate should be reduced by
4% for each 1000 feet above a 2000 foot elevation
in the U.S.A., or 10% for elevations between 2000
and 4500 feet in Canada. If the heating value of the
gas has been reduced, these rules do not apply. To
identify the proper orifice size, check with the local
gas utility.
If installing this appliance at an elevation above 4500
feet (in Canada), check with local authorities.
WARNING
Fire hazard.
Do NOT change the valve settings.
• This valve has been preset at the factory.
• Changing valve settings may result in fire
hazard or bodily injury.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
43
10
Electrical Information
B. Connecting to the Appliance
A. Recommendation for Wire
This appliance requires 110-120 VAC be wired to the
junction box either for use of optional accessories (standing pilot ignition) or for proper operation of the appliance
(Intellifire ignition). Refer to Figure 10.1 to determine if the
appliance uses an Intellifire ignition system or Standing
Pilot ignition system.
WARNING
Wire 110V to electrical junction box.
Do NOT wire 110V to valve.
Do NOT wire 110V to wall switch.
• Incorrect wiring will damage millivolt valves.
• Incorrect wiring will override IPI safety lockout
and may cause explosion.
Open the control access panel to view wiring system and
gas valve. If this appliance has a red or black ignitor button
(as noted in Figure 10.1) this appliance has a Standing Pilot
ignition system. If there is no red or black ignitor button,
this appliance has an Intellifire ignition system.
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
• If using thermostat use one compatible with a millivolt
gas valve system.
• Follow parameters for locating thermostat (see individual
thermostat instructions) to ensure proper operation of
appliance.
• Use low resistance thermostat wire for wiring from ignition system to the wall switch and thermostat.
• Keep wire lengths short as possible by removing any
excess wire length.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
Figure 10.1 Standing Pilot Ignition
• Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
Note: This appliance must be electrically wired and grounded
in accordance with local codes or, in the absence of local
codes, with National Electric Code ANSI/NFPA 70-latest
edition or the Canadian Electric Code, CSA C221.1.
PILOT
THERMOPILE
THERMOCOUPLE
WHITE
PIEZO
RED
VALVE
Figure 10.2 Standing Pilot Ignition Wiring Diagram
44
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
THERMOSTAT
WIRE ASSEMBLY
C. Intellifire Ignition System Wiring
CAUTION
This appliance requires a 110 VAC supply to the appliance
junction box for operation. A wiring diagram is shown in
Figure 10.3 and Figure 10.4.
Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
This appliance is equipped with an Intellifire control valve
which operates on a 3 volt system.
This appliance is supplied with a battery pack and a 3 volt AC
transformer, which requires the installation of the supplied
junction box. It is highly recommended that the junction box
be installed at this time to avoid reconstruction.
D. Standing Pilot Ignition System Wiring
The battery pack requires two D cell batteries (not
included).
• It is recommended that a 110 VAC junction box be installed for use with a fan or remote control. (See Figure
10.5 for junction box wiring).
• This standing pilot ignition system wiring does not require
a 110 VAC supply to operate.
Batteries cannot be placed in the battery pack while
using the 3 volt AC transformer. The transformer must
be unplugged if the battery pack is used or battery life
will be reduced.
WARNING
Shock hazard.
• Replace damaged wire with type 105º C
rated wire.
• Wire must have high temperature insulation.
CAUTION
Do not wire 110 VAC directly to ignition module. Permanent
damage to module will occur. Connect ignition module to 3
VAC transformer as instructed.
CAUTION
Battery polarity must be correct or module damage will occur.
IGNITION MODULE 3 VAC
INTERMITTENT PILOT IGNITOR
I
S
TRANSFORMER
3 VAC
NEUTRAL
HOT
PLUG IN
WHITE
ORANGE
GROUND TO
FIREPLACE
CHASSIS
K
AC
BL
D
RE
ORANGE
GREEN
WIRES
(TO BROWN)
BATTERY PACK
THERMOSTAT
WIRE ASSEMBLY
VALVE
Figure 10.3 Intellifire Ignition Wiring Diagram with Wall Switch or Thermostat
NOTE: 1. Ignition module, valve, pilot, and
wall switch operate on 3 volts. 120 VAC is
required at junction box unless equipped
with battery back-up.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
45
INTERMITTENT
PILOT IGNITOR
IGNITION
MODULE 3 VAC
I
S
TRANSFORMER
3 VAC
ORANGE
NEUTRAL
HOT
WHITE
PLUG IN
GROUND TO
FIREPLACE
CHASSIS
K
AC
BL
D
RE
ORANGE
GREEN
WIRES
(TO BROWN)
BATTERY PACK
REMOTE
PLUG IN
VALVE
Figure 10.4 Intellifire Ignition Wiring Diagram with Remote Receiver
46
NOTE: 1. Ignition module, valve, pilot, and
wall switch operate on 3 volts. 120 VAC is
required at junction box unless equipped
with battery back-up.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
E. Junction Box Installation
Romex
Connector
If the box is being wired from the appliance:
• Remove the screw attaching the junction box to
the outer shell, rotate the junction box inward
to disengage it from the outer shell (see Figure
10.5).
14/2WG
Cover Plate
outside firebox
• Pull the electrical wires from outside the
appliance through this opening into the valve
compartment.
HT
W
WHT B
LK
BLK
• Loosen the two screws on the Romex connector
(not included with unit), feed the necessary
length of wire through the connector and tighten
the screws.
• Make all necessary wire connections to the
receptacle and assemble the receptacle and
cover to the junction box.
GRN wire
inside box
Copper
ground attached
to GRN screw with
GRN wire
NOTE: Do NOT wire
110VAC to wall switch.
Figure 10.5 Junction Box Detail
F. Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall mounted
switch for use with a fan (See Figure 10.6):
• The power supply for the appliance must
be brought into a switch box.
SWITCH
MINIMUM 14-3
AW G
WITH GROUND
• The power can then be supplied from the
switch box to the appliance using a minimum of 14-3 with ground wire.
JUNCTION BOX
POWER
SUPP LY WIRE S
• At the appliance connect the black (hot),
white (neutral) and green (ground) wires
to the junction box as shown.
• Add a 1/4 inch insulated female connector
to the red (switch leg) wire, route it through
the knockout in the face of the junction box,
and connect to the top fan switch connector
(1/4 inch male) as shown.
Black
White
Green
Red
Black
White
Green
• At the switch box connect the black (hot)
wire and red (switch leg) wire to the wall
switch as shown.
Red
Black
White
Green
SWITCH BOX
Red
Figure 10.6 Junction Box Wired to Wall Switch
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
47
11
Finishing
A. Mantel Projections
Figure 11.1 shows the minimum vertical and corresponding
maximum horizontal dimensions of appliance mantels or
other combustible projections above the top front edge of
the appliance.
1/2 IN.
MINIMUM
CEILING
All measurements are in inches.
2-7/8 IN.
MINIMUM
3 FT. MAXIMUM
12
11
Note: Clearance from opening
to perpendicular wall.
10
9
8
32
7
6
5
4
3
4
5
6
7
8
9
10
11
12
Figure 11.3 Mantel Leg (Acceptable on both sides of opening.)
13
TOP OF HOOD OR FIREPLACE OPENING
3 IN.
MINIMUM
5-3/8 IN.
MINIMUM
Figure 11.1 Clearances to Mantels or other Combustibles
above Appliance
UNLIMITED
Note: Clearance from opening
to perpendicular wall.
Figure 11.4 Wall Projection (Acceptable on one side of opening.)
3-1/2 in.
1/2 in. SHEETROCK
OR COMBUSTIBLE
MATERIAL
1/2 in.
SHEETROCK
3-1/2 in.
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
1/2 in.
1/2 in.
NON-COMBUSTIBLE ZONE
NON-COMBUSTIBLE ZONE
Figure 11.2 Non-Combustible Zone
Models: SL-550TR-E, SL-750TR-E
SL-550TR-IPI-E, SL-750TR-IPI-E
48
Figure 11.5 Non-Combustible Zone
Models: SL-950TR-E, SL-950TR-IPI-E
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
B. Facing Material
WARNING
Fire Risk.
Do NOT obstruct air inlet or outlet grilles.
Do NOT modify grilles.
• Modifying or covering grilles could cause
temperature rise and fire hazard.
FINISH WALL MATERIAL
MAY BE COMBUSTIBLE
TOP AND SIDES
TOP SEAL
JOINT
SIDE SEAL
JOINT
Finishing materials must not interfere with:
• Air flow through grilles or louvers.
• Operation of louvers or doors.
• Access for service.
1 INCH
(25 mm)
0 INCH
(0 mm)
FACING MATERIAL UP TO 1/2 IN. THICK
MAY BE COMBUSTIBLE - TOP AND SIDES
NON-COMBUSTIBLE STRIP
SHIPPED WITH UNIT
0 IN.
Figure 11.7 Facing Materials
Models: SL-950TR-E, SL-950TR-IPI-E,
WARNING
1 IN.
0 IN.
0 IN.
HIGH TEMPERATURE (3000F / 1490 C MIN.)
TOP & SIDE SEAL JOINT
BOTTOM 1 INCH (SHADED AREA)
MAY BE COVERED WITH COMBUSTIBLE OR
NON-COMBUSTIBLE MATERIAL.
Figure 11.6 Facing Materials
Models: SL-550TR-E, SL-750TR-E
SL-550TR-IPI-E, SL-750TR-IPI-E
Risk of Fire
• Non-combustible clearances MUST be
maintained.
• Sheetrock, wood or other combustibles must
NOT be used as sheathing or facing in the
non-combustible zone.
• See Section 11 for proper clearances.
• See Section 1 for combustible/non-combustible
definitions.
WARNING
Fire Risk.
Finish all edges and fronts to clearances and
specifications listed in manual.
• Black metal appliance front may be covered with
noncombustible material only.
• Do NOT overlap combustible materials onto appliance
front. The appliance front may only be covered with
noncombustible materials. The bottom one inch of the
appliance front is exempt and may be covered with
either non-combustible or combustible materials.
• Install combustible materials only up to specified
clearances on top, front and side.
• Seal joints between the finished wall and appliance top
and sides using only a 300º F minimum sealant.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
49
C. Splatter Guard
The splatter guard is a piece of corrugated material used
to protect the appliance during the installation process before finishing work on the whole hearth is complete.
Splatter guards may be factory installed or accompany the
door of the unit, depending on the fireplace model. Splatter guards must be removed before appliance is fired.
WARNING
Risk of Fire
• Splatter guard must be removed before lighting
appliance.
• Before splatter guard is installed:
Close ball valve to prevent accidental lighting.
Step 1. Turn off gas to valve. Red gas shutoff knob is
located on ball valve. Disconnect the 3 volt transformer
from the junction box. See Figure 11.6.
Figure 11.8
Step 4. Center the splatter guard in front of the unit as
shown in Figure 11.9. Place the splatter guard in the unit
by guiding the top flap into proper position and then continuing to guide the tabs on the side flaps into the top slot
on the left and right sides of the appliance. The top slot is
indicated in Figure 11.10 Take care not to bend or break
off the tabs.
Figure 11.6
To install the Splatter Guard:
Step 2. Crease flap on top side of splatter guard using the
scored line as the guide. See Figure 11.7.
Figure 11.9
TOP SLOT
Figure 11.7
Step 3. Crease flaps on left and right sides of splatter guard
using the scored line as the guide. See Figure 11.8.
50
Figure 11.10
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
Step 5. Fold bottom flap along score line as indicated in
Figure 11.11 and tuck into valve access area of appliance.
Splatter guard should fit securely on front of unit.
Figure 11.14
Once plumbing and wiring are complete on the fireplace,
the lower access panel may be closed until the time that the
splatter guard must be removed for firing the appliance.
Figure 11.11
Figure 11.15
To Close the Lower Access Panel:
Figure 11.12
Step 6. To open lower access panel of splatter guard,
place one hand above score line and place two fingers
from other hand in the round holes on the front of the
splatter guard. See Figure 11.12. Pull out and fold up
the panel as shown in Figure 11.13. Disengage the tabs
on left and right bottom of splatter guard and fit them into
the square holes. The tabs are now inside the front of
the splatter guard; carefully bend them down. See Figure
11.14.
Carefully disengage the tabs from the square holes and
bend the access panel to its original position. Bend the
center bottom flap and insert it into the bottom of the appliance.
Figure 11.16
To Remove the Splatter Guard:
Figure 11.13
Carefully grab splatter guard on or near the vertical center
on the left and right sides. Pull outward gently, but firmly,
taking care not to tear or remove the inserted tabs.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
51
D. Doors
It’s very important to know what kind of a door and what kind
of finishing material is going to be used on the fireplace. The
table below shows the door models and the finishing material thickness allowed. For an inside fit there is an available
template to assist with sizing the finishing material.
DOOR
FIT
FINISH MATERIAL
THICKNESS
SEE
FIGURE
X
Y
Aero-28
Inside
4 inch max.
11.17
N/A
N/A
Aero-32
Inside
4 inch max.
11.17
N/A
N/A
Aero-36
Inside
4 inch max.
11.17
N/A
N/A
Chad-32E
Overlap
1 inch max.
11.18
N/A
N/A
Chad-32E
Inside
1-4 inches
11.19
32-3/8 in.
30-3/8 in.
Chad-36E
Overlap
1 inch max.
11.18
N/A
N/A
Chad-36E
Inside
1-4 inches
11.19
37-1/4 in.
34 in.
Chad-42E
Overlap
1 inch max.
11.18
N/A
N/A
Chad-42E
Inside
1-4 inches
11.19
44-3/8 in.
38
Halston-32E Overlap
1 inch max.
11.18
N/A
N/A
Halston-32E
1-4 inches
11.20
32-3/8 in.
30-3/8 in.
Halston-36E Overlap
1 inch max.
11.18
N/A
N/A
Halston-36E
1-4 inches
11.20
37-1/4 in.
34 in.
Inside
Halston-42E Overlap
1 inch max.
11.18
N/A
N/A
Halston-42E
1-4 inches
11.20
44-3/8 in.
38 in.
Inside
FINISHING MATERIAL
4 IN. MAXIMUM
THICKNESS
DOOR
SL-550TR-IPI-E (550-Template)
SL-750TR-IPI-E (Template-36)
SL-950TR-IPI-E (950-Template)
UNITS AND
TEMPLATE PART #
Inside
FINISHING MATERIAL
4 IN. MAXIMUM
THICKNESS
Y
X
(Includes 1/8 in. opening each side of door)
Finishing material between 1 and 4 inches thick.
Refer to Table 1 for X and Y dimensions.
Figure 11.19 Inside Fit Door (Chad)
Table 1. Finishing Clearances for Aero, Chad and Halston Fronts
FINISHING
MATERIAL
FINISHING
MATERIAL
FINISHING MATERIAL
4 IN. MAXIMUM THICKNESS
DOOR
FINISHING MATERIAL
4 IN. MAXIMUM THICKNESS
*IF FINISHING MATERIAL IS THICKER THAN
2 IN., DOORS WILL ONLY OPEN
AS FAR AS PICTURED
Stop finishing material flush with fireplace surround opening.
DOORS
Figure 11.17 Aero Door
Y
FRONT FACE OF FIREPLACE
DOOR
1 in. MAX
FINISHING MATERIAL
(TOP EDGE)
X
(Includes 1/8 in. opening each side of door)
Finishing materials 1 inch maximum thick.
Stop finishing material flush with opening.
Figure 11.18 Overlap Fit Door (Chad and Halston)
52
Finishing material between 1 and 4 inches thick.
Refer to Table 1 for X and Y dimensions.
Figure 11.20 Operable Hinge Door (Halston)
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
12
Appliance Setup
A. Remove Shipping Materials
Remove shipping materials from inside or underneath the
firebox.
B. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
C. Accessories
Install only approved accessories per instructions included
with accessories. See your dealer or visit www.heatnglo.
com for appropriate accessories.
RHEOSTAT
SWITCH
TEMPERATURE
SENSOR
Figure 12.1 Blower wiring
WARNING
Shock or fire risk.
Use ONLY optional accessories approved for
this appliance.
• Using non-listed accessories voids warranty.
• Using non-listed accessories may result in a
safety hazard.
• Only Hearth & Home Technologies approved
accessories may be used safely.
VARIABLE
SPEED SWITCH
JUNCTION BOX
TEMPERATURE
SENSOR SWITCH
BLUE
Figure 12.2 Detail of Fan Wiring with Rheostat
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
53
D. Lava Rock, Mineral Wool/Ember Placement
NO EMBERS
WARNING
Explosion Risk.
• Follow ember placement instructions in
manual.
• Do NOT place embers directly over
burner ports.
• Replace ember material annually.
LO
G
Improperly placed embers interferes with proper burner
operation.
Placing the Lava Rock
See Section 12E for Lava Rock placement instructions.
Figure 12.3 Placement of Embers
• Place lava rock on base pan. Do NOT place on burner
top.
Placing the Ember Material
Ember material is shipped with this gas appliance. To place
the ember material:
• Embers CANNOT be placed directly over ports. See
Figure 12.4 for the only exception to this guideline. Care
should be taken not to cover the lighting trail of ports
(from back to front).
• When placing Glowing Embers® onto the burner care
should be taken so that the ports are not covered. Place
the dime-size ember pieces near the port holes in the
burner top (see Figure 12.3). Failure to follow this procedure will likely cause lighting and sooting problems.
• Some of the small port holes should be covered with
ember material. See Figure 12.4 for detail.
PORT HOLES IN CIRCLED
AREA SHOULD BE COVERED
WITH EMBER MATERIAL. NO
OTHER PORT HOLES MAY
COME INTO CONTACT WITH
EMBER MATERIAL.
Figure 12.4
• Save the remaining ember materials for use during appliance servicing. The embers provided should be enough
for 3 to 5 applications.
54
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
E. Positioning the Logs
If the gas logs have been factory installed they should not
need to be positioned. If the logs have been packaged
separately, refer to the following instructions.
Log Set Assembly: LOGS-550-E, 750-E, 950-E
Model: SL-550TR-E, 750TR-E, 950TR-E,
SL-550TV-E, SL-750TV-E, SL-950TV-E
3/8 in.
Note: Figure 1 illustrates the recommended gap between the
burner and the lava rock retainer.
Burner
Carefully remove the logs from the packaging.
CAUTION: Logs are fragile!
Lava Rock
retainer
No lava rock
may be placed
past this edge.
Figure 1
Left rear log tab
Right rear log tab
Indentation
Shoulder screw
1
Lava Rock retainer
Grate tine (4)
Slot
Figure 3
Figure 2
Log # 2 should touch firebox
Left rear log tab
Indentation
1
2
Figure 5
Mate notch with grate tine
Mate slot with tab
Figure 4
Log #1: Locate the slot on the bottom right side of log 1.
Mate the slot with the right rear log tab. Pull the left end of
log #1 forward until it touches the left rear log tab.
Log #2: Mate the left grate tine with the notch located on
the left end of log #2. The right end of log #2 should rest
on log #1 as shown. Be sure that the top of log # 2 touches
the back of the firebox.
2118-935D 6/07
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
55
Log should touch lava rock retainer
3
3
PIN HOLE
Figure 6
Figure 7
Mate shoulder screw with pin hole
Log #3: Locate the pin hole on the underside of log #3.
Mate the pin hole with the shoulder screw located on the
burner top. Push the left end of log # 3 toward the back of
the firebox until it touches the lava rock retainer.
Bump
Bump
Swing knot towards log #3
5
4
Figure 8
Mate notch with grate tine
Log #4: Locate the notch at the end of log # 4. Mate the notch
with the tine as shown above. The top end of log #4 should
rest between the end of log #2, and the bump located on log
#1. Swing the knot on log # 4 towards log #3.
Figure 10
Mate notch with grate tine
Figure 9
Log #5: Locate the notch at the end of log # 5. Mate the
notch with the far right grate tine. The top end of log # 5
should rest on the right side of the “bump” as shown above.
You may need to move log #4 slightly.
SL-550TR-E
SL-550TV-E
SL-750TR-E
SL-750TV-E
SL-950TR-E
SL-950TV-E
Log 1
SRV2115-701
SRV2118-701
SRV2121-701
Log 2
SRV2115-702
SRV2118-702
SRV2121-702
Log 3
SRV2115-703
SRV2118-703
SRV2118-703
Log 4
SRV2115-704
SRV2118-704
SRV2121-704
Log 5
SRV2115-705
SRV2118-705
SRV2121-705
Lava Rock
Step #6: Apply the supplied lava rock as shown above.
Take care to ensure that no lava rock is placed past the line
indicated in Figure 1.
56
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
F. Glass Assembly
G. Grilles and Trim
WARNING
Handle glass doors with care.
• Inspect the gasket to ensure it is
undamaged.
• Inspect the glass for cracks, chips or
scratches.
• Any scratch in glass, requires replacement.
• Do NOT strike, slam or scratch glass.
• Do NOT operate appliance with glass door removed,
cracked, broken or scratched.
• Replace glass door assembly as a complete appliance.
Removing Glass Assembly
Pull the four glass assembly latches out of the groove on
the glass frame. Remove glass door from the appliance
(see Figure 12.5).
Replacing Glass Assembly
Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame.
Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other non-combustible
materials can be used to cover up the gap between the
sheet rock and the appliance.
Do not obstruct or modify the air inlet/outlet grilles or hood.
When overlapping on both sides, leave enough space so
that the bottom grille can be lowered and the trim door
removed.
H. Air Shutter Setting
This appliance has an adjustable air shutter (which controls the primary air) factory set for the minimum vertical
vent run (see Figure 12.6). If your installation has more
than the minimum required vertical vent length, adjustment of the air shutter may be necessary to obtain optimal
flame appearance. This should be adjusted by a qualified installer at the time of installation.
By sliding the air shutter to the right, you will be closing
the air shutter. To adjust loosen the wing nut. Care should
be taken when adjusting the air shutter so as not to cause
the appliance to soot. If sooting occurs the air shutter will
need to be opened by sliding the air shutter to the left.
When finished, tighten wing nut.
L ATCHE S
(BOTH BOT TO M
AND TOP )
GLASS
ASSEMB LY
Figure 12.5 Glass Assembly
S H U TTE R A D JU S TM E N T
Figure 12.6
Shutter Settings
Models
NG
LP
SL-550TR-E
3/16 in.
3/16 in.
SL-750TR-E
3/16 in.
3/16 in.
SL-950TR-E
3/8 in.
Full Open
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
57
13
Operating Instructions
A. Before Lighting Appliance
Before lighting this appliance determine if it has a Standing
Pilot or Intellifire ignition system by opening the control
access panel to view wiring system and gas valve. If this
appliance has a red or black ignitor button (see Figure
10.1) this appliance has a Standing Pilot ignition system.
If there is no red or black ignitor button, this appliance has
an Intellifire ignition system.
CAUTION
If installing Intellifire ignition battery backup:
• Do not install batteries if the backup mode may not be
used for extended time.
• Batteries may leak.
• Install batteries only when needed for power outage.
Before operating this appliance have a qualified technician:
• Remove all shipping materials from inside and/or underneath the firebox.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. Do
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
• Review proper placement of logs, rockwool, lava rock,
and vermiculite.
• Check the wiring.
WARNING
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
• Ensure that the glass is sealed and in the proper position.
• Ensure that the flow of combustion and ventilation air is
not obstructed (front grilles and vent caps).
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to
the owner’s information manual provided with this appliance.
For assistance or additional information consult a qualified
installer, service agency or the gas supplier.
WARNING
WARNING
Glass door must be in place when appliance
is operating.
Risk of:
• Combustion Fumes
• Fire
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
Do NOT operate appliance with glass door
removed.
• Open viewing glass for servicing only.
• Glass door MUST be in place and sealed before operating
appliance.
• Only use glass door certified for use with appliance.
• Glass replacement should be done by qualified technician.
58
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
B. Lighting Instructions (IPI)
The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burner. DO NOT try to light the burner by
hand.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
C. DO NOT use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
LIGHTING
INSTRUCTIONS
(IPI)
1. Turn off all electric power to the appliance.
2. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
• If you cannot reach your gas supplier, call the fire department.
• DO NOT touch any electric switch; do
not use any phone in your building.
GAS
VALVE
3. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this label. If you do not smell gas, go to next step.
4. Turn on all electric power to the appliance.
WARNING:
CAUTION:
DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gasoline and other liquids having flammable
vapors away.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause cancer, birth defects, or other reproductive
harm.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
NOT FOR USE
WITH SOLID FUEL
5. To light the burner, flip the ON/OFF switch to
the “ON” position. (The ON/OFF switch may
include a wall switch if so equipped).
6. If the appliance will not operate, follow the instructions “To Turn Off Gas to Appliance” and
call your service technician or gas supplier.
TO TURN OFF
GAS TO APPLIANCE
1. Turn wall control or ON/OFF switch to “OFF”.
2. Turn off all electric power to the appliance if
service is to be performed.
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
593-913F
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Final inspection by
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
59
Standing Pilot Ignition
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
1. Open control access panel.
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which
must be lighted by hand. When
lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or
turn the gas control knob. Never use
tools. If the knob will not push in or
turn by hand, DO NOT try to repair
it, call a qualified service technician.
Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WARNING:
CAUTION:
DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gasoline and other liquids having flammable
vapors away.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause cancer, birth defects, or other reproductive
harm.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
NOT FOR USE
WITH SOLID FUEL
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
2. Turn off all electric power to
the appliance.
3. Push in gas control knob
slightly and turn clockwise
to “OFF”.
Note: Knob cannot be turned from “PILOT” to “OFF”
unless knob is pushed in slightly. DO NOT force.
4. Open the fixed glass assembly. You may need to
remove the decorative front.
5. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow “B” in the Safety
Information located on the left side
of this label. If you don’t smell gas,
go to next step.
6. Find the pilot. The pilot is inside
combustion chamber next to the
main burner
7. Turn knob on gas control counterclockwise
to “PILOT”.
8. Push in control knob all the way and hold in. Immediately depress red or black piezo button. It may require
several depressions of the red or black piezo button
until PILOT lights. If PILOT light does not light after
10 seconds, return to step 3. Continue to hold the
control knob in for about one minute after the pilot is
lit. Release knob and it will pop back out. Pilot should
remain lit. If it goes out, repeat steps 3 through 6.
• If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.
• If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your service technician or gas supplier.
9. Reinstall fixed glass assembly. Reinstall decorative
front.
10. Turn gas control knob counterclockwise
to “ON”. Close access panel.
11. Turn on all electric power to the appliance.
12. To light burner, turn the wall control or on/off switch
to “ON”.
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
TO TURN OFF
GAS TO APPLIANCE
For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
1. Turn off all electric power to the appliance if service is to be performed.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
2. Open control access panel.
3. Move switch to “OFF” position.
4. Push in gas control knob slightly and turn clockwise
to OFF”. DO NOT force.
5. Close control access panel.
Final inspection by
60
464-903H
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
C. After Appliance is Lit
Initial Break-in Procedure
When you light the appliance, you may notice that it produces heat which does have an associated odor or smell.
If you feel this odor is excessive it may require the initial
three to four hour continuous burn on high followed by a
second burn up to 12 hours to fully drive off any odor from
paint and lubricants used in the manufacturing process.
Condensation of the glass is normal.
NOTE: The appliance should be run three to four hours
on the initial start-up. Turn it off and let it cool completely.
Remove and clean the glass. Replace the glass and run
the appliance for an additional 12 hours. This will help to
cure the products used in the paint and logs.
During this break-in period it is recommended that some
windows in the house be opened for air circulation. This will
help avoid setting off smoke detectors, and help eliminate
any odors associated with the appliance’s initial burning.
CAUTION
• Prevent accidental appliance operation when not
attended.
• Unplug or remove batteries from remote control if absent
or if appliance will not be used for an extended period of
time.
• Property damage possible from elevated temperatures.
CAUTION
Smoke and odors released during initial operation.
• Open windows for air circulation.
• Leave room during initial operation.
• Smoke may set off smoke detectors.
Smoke and odors may be irritating to sensitive
individuals.
WARNING
Fire Risk.
High Temperatures.
Keep combustible household items away from
appliance.
Do NOT obstruct combustion and ventilation air.
• Do NOT place combustible items on top of or
in front of appliance.
• Keep furniture, draperies away from
appliance.
WARNING
Fire Hazard.
Keep combustible materials, gasoline and
other flammable vapors and liquids clear of
appliance.
• Do NOT store flammable materials in the
appliance’s vicinity.
• Do NOT use gasoline, lantern fuel, kerosene,
charcoal lighter fluid or similar liquids in this
appliance.
• Combustible materials may ignite.
D. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance is allowed to burn for 20 to 40 minutes.
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may also be released from finishing materials and adhesives used around the
appliance.
Film on the glass
Metallic noise
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Is it normal to see the pilot flame burn In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off when
continually?
ON/OFF is turned off. In a standing pilot system the pilot will always stay on.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
61
14
Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the
corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.
A. Standing Pilot Ignition System
Symptom
Possible Causes
Corrective Action
1. After repeated triggering a. Defective ignitor.
of the red or black piezo
ignitor button, the spark
b. Defective pilot or misaligned
ignitor will not light the pilot.
electrode (spark at electrode).
Check the spark at the electrode and pilot. If no spark and electrode
wire is properly connected, replace the ignitor.
c. No gas or low gas pressure.
Check the remote shut-off valves from the fireplace. Usually, there
is a valve near the gas main. There can be more than one (1) valve
between the fireplace and the main.
d. No LP in tank.
Check the LP (propane) tank. You may be out of fuel.
a. Defective thermocouple.
Check that the pilot flame impinges on the thermocouple. Clean
and/or adjust the pilot for maximum flame impingement.
2. The pilot will not stay lit
after carefully following the
lighting instructions.
Using match, light the pilot. If the pilot lights, turn off the pilot and
trigger the red piezo ignitor button again. If the pilot lights, an improper gas/air mixture caused the bad lighting and a longer purge
period is recommended. If the pilot will not light, ensure the the gap
at the electrode and pilot is one-eighth (1/8) inch to have a strong
spark. If the gap is OK, replace the pilot.
Ensure that the thermocouple connection at the gas valve is fully
inserted and tight (hand tighten plus 1/4 turn).
Disconnect the thermocouple from the valve, place one millivolt
meter lead wire on the tip of the thermcouple and the other meter
lead wire on the thermocouple copper lead. Start the pilot and hold
the valve knob in. If the millivolt reading is less than 15mV, replace
the thermocouple.
b. Defective valve.
3. The pilot is burning,
a. ON/OFF switch or wires
there is no burner flame ,
defective.
the valve knob is in the ON
position, and the ON/OFF
switch is in the ON position.
If the thermocouple is producing more than 15 millivolts, replace
faulty valve.
Check the ON/OFF switch and wires for proper connections. Place
the jumper wires across the terminals at the switch. If the burner
comes on, replace the defective switch. If the switch is OK, place the
jumper wires across the switch wires at the gas valve. If the burner
comes on, the wires are faulty or connections are bad.
b. Thermopile may not be gener- If the pilot flame is not close enough physically to the thermopile,
ating sufficient millivoltage.
adjust the pilot flame.
Be sure the wire connections from the thermopile at the gas valve
terminals are tight and that the thermopile is fully inserted into the
pilot bracket.
Check the thermopile with a millvolt meter. Take the reading at
TH-TP&TP terminals of the gas valve. The meter should read 325
millivolts minimum, while holding the valve knob depressed in the
pilot position, with the pilot lit, and the ON/OFF switch in the OFF
position. Replace the faulty thermopile if the reading is below the
specified minimum.
With the pilot in the ON position, disconnect the thermopile leads
from the valve. Take a reading at the thermopile leads. The reading should be 325 millivolts minimum. Replace the thermopile if the
reading is below the minimum.
62
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
Troubleshooting (continued)
Symptom
3. Continued
Possible Cause
Corrective Action
c. Defective valve.
Turn the valve knob to the ON position. Place the
ON/OFF switch in the ON position. Check the millivolt
meter a the thermopile terminals. The millivolt meter
should read greater than 125mV. If the reading is acceptable, and if the burner does not come on, replace
the gas valve.
d. Plugged burner orifice.
Check the burner orifice for stoppage. Remove stoppage.
e. Wall switch or wires are defective.
Follow the corrective action in Symptom and Possible Cause 1.a above. Check the switch and wiring.
Replace where defective.
4. Frequent pilot outage a. Pilot flame may be too high or too low, or blowproblem.
ing out (high pressure), causing pilot safety to
drop out.
Clean thermocouple and adjust the pilot flame for
maximum flame impingement. Follow lighting instructions carefully.
5. The pilot and main
burner extinguish while
in operation.
a. No LP in tank.
Check the LP (propane) tank. Refill the fuel tank.
b. Inner vent pipe leaking exhaust gases back
into the system.
Check venting system for damage. Replace/repair
improperly assembled pipe sections.
c. Glass too loose and air tight packet leaks in
corners after usage.
Replace glass panel assembly.
d. Bad thermopile or thermocouple.
Replace if necessary.
e. Improper vent cap installation.
Check for proper installation and freedom from debris
or blockage.
a. Flame impingement.
Adjust the log set so that the flame does not excessively impinge on it.
b. Improper air shutter setting.
Adjust the air shutter located on the control panel.
c. Debris around air shutter.
Inspect the opening at the base of the burner. NO MATERIAL SHOULD BE PLACED IN THIS OPENING.
a. Insufficient oxygen being supplied.
Ensure that the vent cap is installed properly and free
of debris. Ensure that the vent system joints are tight
and have no leaks.
6. Glass soots.
7. Flame burns blue
and lifts off burner.
Ensure that no debris has been placed at the base of,
or in the area of the air holes in the center of the base
pan beneath the burner.
Ensure that the glass is tightened properly on the unit,
particularly on top corners.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
63
B. Intellifire Ignition System
Sympton
1. The ignitor/module
makes noise, but no
spark.
2. Pilot won’t light,
there is no noise or
spark.
Possible Cause
Corrective Action
a. Incorrect wiring.
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor
are connected to correct terminals on module and pilot assembly.
Reversed wires at the module may cause system to make sparking
noise, but spark may not be present at pilot hood.
b. Loose connections or electrical
shorts in the wiring.
Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Rod closest to pilot hood should be ignitor.
Verify connections underneath pilot assembly are tight; also verify
connections are not grounding out to metal chassis, pilot burner,
pilot enclosure, mesh screen if present, or any other metal object.
c. Ignitor gap is too large.
Verify gap of igniter to pilot hood. The gap should be approximately
.17 inch or 1/8 inch.
d. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
a. Transformer installed correctly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
b. A shorted or loose connection in wir- Remove and reinstall the wiring harness that plugs into module.
ing configuration or wiring harness.
Verify there is a tight fit. Verify pilot assembly wiring to module.
Remove and verify continuity of each wire in wiring harness.
3. Pilot lights but continues to spark, and
main burner will not ignite. (If the pilot continues to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
64
c. Improper wall switch wiring.
Verify that 110/VAC power is “ON” to junction box.
d. Module not grounded.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
e. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
a. A shorted or loose connection in
sensor rod.
Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight. Verify connections are
not grounding out to metal chassis, pilot burner, pilot enclosure or
screen if present, or any other metal object.
b. Poor flame rectification or contaminated sensor rod.
Verify that flame is engulfing sensor rod. If the pilot assembly does
not have a ground strap, consider installing one to increase flame
rectification. Verify correct pilot orifice is installed and inlet gas
specifications. Flame carries rectification current, not the gas. If
flame lifts from pilot hood, the circuit is broken. A wrong orifice or
too high an inlet pressure can cause pilot flame to lift. The sensor
rod may be contaminated. Clean sensor rod with emery cloth.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
Intellifire Ignition System - (continued)
Symptom
3. (Continued) Pilot lights
but continues to spark,
and main burner will not
ignite. (If the pilot continues to spark after the pilot
flame has been lit, flame
rectification has not occurred.)
4. Pilot sparks, but Pilot
will not light.
Possible Cause
Corrective Action
c. Module is not grounded.
Verify that module is securely grounded to metal chassis
of appliance. Verify that wire harness is firmly connected to
module.
d. Damaged pilot assembly or dirty sensor
rod.
Verify that ceramic insulator around the sensor rod is not
cracked, damaged, or loose. Verify connection from sensor rod to white sensor wire. Clean sensor rod with emery
cloth to remove any contaminants that may have accumulated on sensor rod. Verify continuity with a multimeter with
ohms set at lowest range.
e. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire “I” from module. Place ON/OFF
Rocker switch or wall switch in ON position. Hold ground
wire about 3/16 inch away from “I” terminal on module. If
there is no spark at “I” terminal module must be replaced.
If there is a spark at “I” terminal, module is fine. Inspect
pilot assembly for shorted sparker wire or cracked insulator
around electrode.
a. Correct gas supply.
Verify that incoming gas line ball valve is “open”. Verify that
inlet pressure reading is within acceptable limits, inlet pressure must not exceed 14 in. W.C.
b. Ignitor gap is too large.
Verify that spark gap from ignitor to pilot hood is .17 in. or
1/8 in.
c. Module is not grounded.
Verify module is securely grounded to metal chassis of
appliance.
d. Module voltage output / Valve/Pilot
solenoid ohms readings.
Verify battery voltage is at least 2.7 volts. Replace batteries if voltage is below 2.7.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
65
15
Maintaining and Servicing Appliance
Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified
service technician should perform an appliance check-up at the beginning of each heating season.
WARNING
CAUTION
Risk of injury or property damage.
Before servicing:
• Turn off gas.
• Turn off electricity to appliance.
• Disable remote control, if one is present.
• Ensure appliance is completely cooled.
After servicing:
• Replace any screen or barrier that was removed.
• Reseal and reinstall any venting removed for servicing.
Handle glass assembly with care.
WARNING
Annual inspection by qualified technician recommended.
Check:
• Condition of doors, surrounds and fronts.
• Condition of glass, glass assembly and glass seal.
• Obstructions of combustion and ventilation air.
• Condition of logs.
• Condition of firebox.
• Burner ignition and operation.
• Burner air shutter adjustment
• Gas connections and fittings.
• Obstructions of termination cap.
Clean:
• Glass
• Air passageways, grilles,
control compartment
• Burner, burner ports
NOTE: Clean glass after initial 3-4 hours operation.
Longer operation without cleaning glass may
cause a permanent white film on glass.
When cleaning glass door:
• Avoid striking, scratching or slamming glass.
• Do NOT use abrasive cleaners.
• Use a hard water deposit glass cleaner on white film.
• Do NOT clean glass when hot.
• Turn off appliance after 3-4 hours of operation and
ALLOW TO COOL.
• Remove and clean glass assembly.
• Replace glass assembly and operate appliance for
additional 12 hours.
Refer to maintenance instructions.
WARNING
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
• Combustible materials blocking cap may ignite.
• Restricted air flow affects burner operation.
Risk of:
• Fire
• Delayed ignition or explosion
• Exposure to combustion fumes
• Odors
66
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
A. Maintenance Tasks
Inspect
Doors, Surrounds
and Fronts
Maintenance Tasks
1. Assess condition of screen and replace as necessary.
Recommend addition of screen if one is not present.
2. Inspect for scratches, dents or other damage and repair as necessary.
3. Verify no obstructions to airflow through the louvers.
4. Verify maintenance of proper clearance to combustible household objects.
Gasket Seal, Glass
Assembly and
Glass
1. Inspect gasket seal and its condition.
2. Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.
3. Confirm there is no damage to glass or glass frame. Replace as necessary.
4. Verify that latches engage properly, clip studs are not stripped, and glass attachment components are
intact and operating properly. Replace as necessary.
5. Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.
Valve Compartment
and Firebox Top
1. Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw
tips that have penetrated the sheet metal are sharp and should be avoided.
2. Remove any foreign objects.
3. Verify unobstructed air circulation.
Logs
1. Inspect for broken, damaged, or missing logs. Replace as necessary.
2. Verify correct log placement and no flame impingement causing sooting. Correct as necessary.
Firebox
1. Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.
2. Replace appliance if firebox has been perforated.
Burner Ignition and
Operation
1. Verify burner is properly secured and aligned with pilot or igniter.
2. Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.
3. Replace ember materials with new dime-size and shape pieces. Do not block ports or obstruct lighting paths.
4. Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.
5. Inspect for lifting or other flame problems.
6. Verify air shutter is clear of dust and debris.
7. Inspect orifice for soot, dirt or corrosion.
8. Verify manifold and inlet pressures. Adjust regulator as required.
9. Inspect pilot flame strength. Clean or replace orifice as necessary.
10. Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Clean with emery
cloth or replace as required.
11. Verify millivolt output. Replace as necessary.
Venting
1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.
2. Confirm that termination cap remains clear and unobstructed by plants, etc.
3. Verify that termination cap clearance to subsequent construction (building additions, decks, fences or
sheds) has been maintained.
4. Inspect for corrosion or separation.
5. Verify weather stripping, sealing and flashing remains intact.
6. Inspect draft shield to verify it is not bent, damaged or missing.
Remote controls
1. Verify operation of remote.
2. Replace batteries in remote transmitters and battery-powered receivers.
3. Verify batteries have been removed from battery back-up IPI systems to prevent premature battery failure
or leaking.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
67
16
Reference Materials
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
O
N
P
M
Q
L
ØR
ØK
GAS LINE ACCESS
C
J
I
E
D
V
H
F
S
B
T
U
A
SL-550TR-E
Location
Inches
ELECTRICAL
ACCESS
G
SL-750TR-E
Millimeters
SL-950TR-E
Inches
Millimeters
Inches
A
36
913
41
1041
48
1218
B
31-1/8
791
36-1/8
917
43
1092
C
27-3/16
691
32-1/16
815
39-1/16
993
D
18-1/16
459
21-1/2
547
23-9/16
599
E
31-1/8
790
34-5/8
879
38-9/16
980
F
3-9/16
90
3-9/16
90
3-9/16
90
G
6-7/8
174
6-7/8
174
6-7/8
174
H
23-3/8
594
26-7/8
683
30-7/8
785
I
34-3/8
873
37-7/8
962
41-7/8
1063
J
35-1/2
902
39-15/16
1015
43-15/16
1117
K
8
203
8
203
8
203
L
8-13/16
223
8-13/16
223
8-13/16
223
M
16-5/16
415
16-5/16
415
16-5/16
415
N
1/2
13
1/2
13
1/2
13
O
25-3/4
653
30-3/4
781
37-3/4
959
P
12-7/8
326
15-3/8
391
18-7/8
478
Q
15-7/8
403
15-7/8
403
15-11/16
406
R
6-5/8
168
6-5/8
168
6-5/8
168
S
2-3/16
55
2-3/16
55
2-3/16
55
T
6
152
6
152
6
152
U
1
25
1
25
1
25
V
30-1/16
764
33-9/16
853
37-9/16
955
Figure 16.1 Appliance Dimensions
68
Millimeters
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
B. Vent Components Diagrams
Pipe
E f fe c tive
H e ig h t / L e n g t h
D V P P ip e (se e c h a r t)
Effective Length
Inches
Millimeters
DVP4
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
DVP12MI 3 to 12
76 to 305
DVP24MI 3 to 24
76 to 610
1 0 -1 /2 in .
(267 m m )
45°
4 -7 /8 in .
( 276 m m )
10 -7/ 8 in .
(2 7 6 m m )
D V P 4 5 (4 5 ° E lb o w )
11- 3 /8 in .
(289 m m )
1 0 in .
(2 5 4 m m )
10 in .
(2 5 4 m m )
1 in .
(25 m m )
7- 3 / 8 in .
(18 7 m m )
2 4 in .
( 610 m m )
1-1 /4 in . (3 2 m m )
9 -1 /4 in .
(235 m m )
1 /2 in . T Y P
(13 m m )
13 -1 /4 in .
(3 37 m m )
D V P - F S ( C e ilin g F ire s to p )
D V P - A S (A t tic S h ie ld )
D V P 9 0 S T ( 9 0 ° E lb o w )
12 in .
(3 0 5 m m )
1- 1 /2 in .
(3 8 m m )
10 in .
(2 5 4 m m )
UP
5 in .
(12 7 m m )
1 in .
(25 m m )
8 in .
(2 0 3 m m )
14 in .
(356 m m )
12 in .
(305 m m )
6 in .
(15 2 m m )
D V P - H V S ( V e n t S u p p o r t)
D V P - W S ( W a ll S h ie ld F ire s to p )
Figure 16.2 DVP vent components
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
69
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-5/8 in.
79 mm
117 mm
5-3/8 in.
9-3/8 in.
137 mm
238 mm
Trap1
Max
Effective
Length
12 in.
(305 mm)
Trap2
DVP-TRAP
Horizontal Termination Cap
DVP-TRAP1
DVP-TRAP2
DVP-TRAPK1
DVP-TRAPK2
DVP-HPC1
DVP-HPC2
Figure 16.3 DVP vent components
70
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
B. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(367 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(127 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(367 mm)
RF6M
Roof Flashing Multi-pak
RF12M
Roof Flashing Multi-pak
5 in.
(127 mm)
13-3/4 in.
(349 mm)
11-7/8 in.
(302 mm)
5 in.
(127 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
BEK
Trap Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
DVP-TRAPFL
Flashing
DVP-HSM-B
Extended Heat Shield
COOL-ADD
Cap Shield
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
14 in.
(356 mm)
DRC-RADIUS
Cap Shield
Figure 16.4 DVP vent components
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
71
B. Vent Components Diagrams (continued)
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
3-7/8 in.
(98 mm)
17-3/4 in.
(451 mm)
14 in.
(356 mm)
10-1/2 in.
(267 mm)
DVP-TV
Vertical Termination Cap
12 in.
(305 mm)
DVP-TB1
Basement Vent Ca p
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
5-1/4 in.
(133 mm)
DVP-TVHW
Ver tic a l Te rm ina tio n C ap (H igh w ind )
PVK-80
(For use with IPI and DSI appliances only.)
14 in.
(356 mm)
16-7/8 in.
(429 mm)
12 in.
(305 mm)
7-1/8 in.
(181 mm)
12-1/8 in.
(314 mm)
8-3/4 in.
(222 mm)
1 in.
(25 mm)
14 in.
(356 mm)
3/8 in. (10 mm)
1 in. (25 mm)
1-5/8 in.
(41 mm)
DVP-HPC
High Performance Cap
Figure 16.5 DVP vent components
72
7-1/4 in.
(184 mm)
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
7-3/4 to 10-3/8 in.
(197 to 264 mm)
DVP-FBHT
Fire B rick Ter m ina tio n C a p
B. Vent Components Diagrams (continued)
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
8-3/8 in.
213 mm
5-1/2 in.
140 mm
87°
3°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
DVP-HRC-SS
DVP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
Figure 16.6 DVP vent components
WARNING
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZCSS termination caps on top vented fireplaces,
a one foot minimum vertical vent section is
required before installing first elbow.
• When using DVP-TB1 termination cap on top vented
fireplaces, a three foot minimum vertical vent section is required
before installing first elbow.
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
5-1/2 in.
140 mm
87°
8-3/8 in.
213 mm
3°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
SLP-HRC-SS
SLP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
DVP-TB1
SLP90
DVP-TB1
SL-2DVP
ASSEMBLY
Figure 16.6 SLP Series Vent Components
DVP-TB1
HORIZONTAL TERMINATION CAP
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
73
B. Vent Components Diagrams (continued)
6-1/2 in.
165 mm
6-1/2 in.
165 mm
8-3/4 in.
222 mm
6-1/2 in.
165 mm
9-1/4 in.
235 mm
6 in.
152 mm
6-5/8 in.
168 mm
SLP45
45° Elbow
6-5/8 in.
168 mm
9-7/8 in.
SLP90
90° Elbow
Effective Height/Length
Effective
Height/
Length
SLP-PIPE
Pipe
inches
mm
SLP4
4
102
SLP6
6
152
SLP12
12
305
SLP24
24
610
SLP36
36
914
SLP48
48
1219
SLP6A
2-6
51 - 152
SLP12A
2 - 12
51 - 305
SLP-FLEX-2
24
610
SLP-FLEX-3
36
914
SLP-FLEX-5
60
1524
SLP-FLEX-10
120
3048
EFFECTIVE HEIGHT/
LENGTH
SLP-FLEX-PIPE
26 in.
660 mm
DVP-HSM-B
Extended Heat Shield
SLP-HVS
Horizontal Pipe
Support
RF4-8
Roof Flashing
SLP-FS
Ceiling Firestop
Figure 16.7 SLP Series Vent Components
74
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
SLP-WS
Wall Shield Firestop
B. Vent Components Diagrams (continued)
SLP-DCF-BK
Ceiling Firestop
Black
SLP-TRAP1
Horizontal
Termination Cap
SLP-TVHW
Vertical
Termination Cap
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
SLK-SNKD
Snorkel
Termination Cap
SLP-TRAP2
Horizontal
Termination Cap
PVK-80
(For use with IPI and DSI appliances only.)
SLP-WT-BK
Wall Thimble-Black
SL-2DVP
Adapter
DVP-FBHT
SLP90
SL-2DVP
DVP-FBHT
SLP-FLEX-TRAP
Horizontal
Termination Kit
Figure 16.8 SLP Series Vent Components
ASSEMBLY
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
75
C. Service Parts
SL-550TR-E, SL-550TR-IPI-E
Service Parts Diagram
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
6
7
9
8
Log Set Assembly
2
4 1
3
Part number list on following page.
76
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
5
C. Service Parts List
SL-550TR-E, SL-550TR-IPI-E
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-550-E
1
Log 1
SRV2115-701
2
Log 2
SRV2115-702
3
Log 3
SRV2115-703
4
Log 4
SRV2115-704
5
Log 5
SRV2115-705
6
Burner NG, LP
2115-007
7
Grate Assembly
2115-015
8
Glass Door Assembly
GLA-550TR
Y
9
Junction Box
4021-013
Y
Exhaust Baffle
530-299
Y
Y
Gasket Assembly
Contains Burner neck, shutter bracket, vent, seal cap,
valve plate, and air passage gaskets
2115-080
Glass Latch Assembly
386-122A
Lava Rock
060-721
Mineral Wool
050-721
Pilot Tube
SRV485-301
Touch Up Paint
203-9
Y
Y
STANDING PILOT CONVERSION KITS
Thermocouple
2103-511
Y
Thermopile
2103-512
Y
Conversion Kit NG
NGKS-550TR-E
Y
Conversion Kit LP
LPKS-550TR-E
Y
2103-116
Y
Pilot Orifice LP
2103-117
Y
Regulator NG
230-1570
Y
Regulator LP
230-1520
Y
Conversion Kit NG
NGK-550IPIE
Y
Conversion Kit LP
LPK-550IPIE
Y
Pilot Orifice NG
593-528
Y
Pilot Orifice LP
593-527
Y
Regulator NG
NGK-DXV
Y
Regulator LP
LPK-DXV
Y
Pilot Orifice NG
IPI CONVERSION KITS
Additional service part numbers appear on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
77
SL-750TR-E, SL-750TR-IPI-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
Service Parts Diagram
6
7
9
8
Log Set Assembly
2
4 1
3
Part number list on following page.
78
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
5
Service Parts List
SL-750TR-E, SL-750TR-IPI-E
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your
appliance please provide model number and serial number. All parts listed in this manual may be ordered
from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked at
Depot
PART NUMBER
Log Set Assembly
LOGS-750-E
1
Log 1
SRV2118-701
2
Log 2
SRV2118-702
3
Log 3
SRV2118-703
4
Log 4
SRV2118-704
5
Log 5
SRV2118-705
6
Burner NG, LP
2118-007
7
Grate Assembly
2118-015
8
Glass Door Assembly
GLA-750TR
Y
Junction Box
4021-013
Y
Exhaust Baffle
530-299
9
Y
Y
Gasket Assembly
Contains Burner neck, shutter bracket, vent, seal cap, valve plate,
and air passage gaskets
2118-080
Glass Latch Assembly
386-122A
Lava Rock
060-721
Mineral Wool
050-721
Pilot Tube
SRV485-301
Touch Up Paint
203-9
Y
Y
STANDING PILOT CONVERSION KITS
Thermocouple
2103-511
Y
Thermopile
2103-512
Y
Conversion Kit NG
NGKS-750TR-E
Y
Conversion Kit LP
LPKS-750TR-E
Y
Pilot Orifice NG
2103-116
Y
Pilot Orifice LP
2103-117
Y
Regulator NG
230-1570
Y
Regulator LP
230-1520
Y
Conversion Kit NG
NGK-750IPIE
Y
Conversion Kit LP
LPK-750IPIE
Y
Pilot Orifice NG
593-528
Y
Pilot Orifice LP
593-527
Y
Regulator NG
NGK-DXV
Y
Regulator LP
LPK-DXV
Y
IPI CONVERSION KITS
Additional service part numbers appear on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
79
SL-950TR-E, SL-950TR-IPI-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
Service Parts Diagram
6
7
8
9
11
10
Log Set Assembly
2
4
3
Part number list on following page.
80
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
1
5
Service Parts List
SL-950TR-E, SL-950TR-IPI-E
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-950-E
1
Log 1
SRV2121-701
2
Log 2
SRV2121-702
3
Log 3
SRV2118-703
4
Log 4
SRV2121-704
5
Log 5
SRV2121-705
6
Non Combustible Board
560-401
7
Burner NG, LP
2121-007
8
Burner Skirt
2121-142
9
Grate Assembly
2121-015
10
Glass Door Assembly
GLA-950TR
Y
11
Junction Box
4021-013
Y
Exhaust Baffle
530-299
Y
Y
Gasket Assembly
Contains Burner neck, shutter bracket, vent, seal cap,
valve plate, and air passage gaskets
2121-080
Glass Latch Assembly
386-122A
Lava Rock
060-721
Mineral Wool
050-721
Pilot Tube
SRV485-301
Touch Up Paint
203-9
Y
Y
STANDING PILOT CONVERSION KITS
Thermocouple
2103-511
Y
Thermopile
2103-512
Y
Conversion Kit NG
NGKS-950TR-E
Y
Conversion Kit LP
LPKS-950TR-E
Y
Pilot Orifice NG
2103-116
Y
Pilot Orifice LP
2103-117
Y
Regulator NG
230-1570
Y
Regulator LP
230-1520
Y
Conversion Kit NG
NGK-950IPIE
Y
Conversion Kit LP
LPK-950IPIE
Y
Pilot Orifice NG
593-528
Y
Pilot Orifice LP
593-527
Y
Regulator NG
NGK-DXV
Y
Regulator LP
LPK-DXV
Y
IPI CONVERSION KITS
Additional service part numbers appear on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
81
Service Parts
SL-550 / 750 / 950TR-IPI-E
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
Valve Assembly Parts List
1
IPI Valve Assembly
2
10
11
3
9
8
12
4
5
6
7
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
PART NUMBER
Pilot Assembly NG
2090-012
Y
Pilot Assembly LP
2090-013
Y
2
Shutter Bracket Assembly
2118-121
Y
3
Battery Pack
593-594A
Y
4
Flex Tube Assembly
7000-156
Y
5
3 Volt Transformer
593-593A
Y
6
Module Wire Assembly
593-590A
Y
7
Thermostat Wire Assembly
2118-170
Y
8
Module
593-592
Y
Valve NG
750-500
Y
1
9
Valve LP
750-501
Y
10
Flex Ball Valve Assembly
302-320A
Y
11
Valve Bracket
2118-104
Orifice NG (#44C)
Orifice LP (#55C)
12
Orifice NG (#42C)
Orifice LP (#54C)
Orifice NG (#37C)
Orifice LP (#52C)
82
SERIAL #
Stocked
at Depot
SL-550TR-E
SL-750TR-E
SL-950TR-E
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
582-844
Y
582-855
Y
582-842
Y
582-854
Y
582-837
Y
582-852
Y
Service Parts
SL-550 / 750 / 950TR-E
Valve Assembly Parts List
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
Standing Pilot Valve Assembly
1
2
9
8
3
7
4
6
5
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Pilot Assembly NG
2103-010
Y
Pilot Assembly LP
2103-011
Y
2
Shutter Bracket Assembly
2118-121
Y
3
Flex Tube Assembly
7000-156
Y
4
Thermostat Wire Assembly
2045-024
Y
Valve NG
230-0710
Y
Valve LP
230-0720
Y
6
Piezo Ignitor
291-513
Y
7
Flex Ball Valve Assembly
302-320A
Y
8
Valve Bracket
2118-104
1
5
Orifice NG (#44C)
Orifice LP (#55C)
9
Orifice NG (#42C)
Orifice LP (#54C)
Orifice NG (#37C)
Orifice LP (#52C)
SL-550TR-E
SL-750TR-E
SL-950TR-E
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
582-844
Y
582-855
Y
582-842
Y
582-854
Y
582-837
Y
582-852
Y
83
D. Limited Lifetime Warranty
Hearth & Home Technologies LIMITED WARRANTY
Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet
and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada.
Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Components Covered
Gas
Wood
Pellet
EPA
Wood
Electric
Venting
X
X
X
X
X
X
X
X
Igniters, Electronic Components,
and Glass
X
X
Blowers
X
X
All Parts and Material Except as
covered by Conditions, Exclusion,
and Limitations listed
X
3 years
Molded Refractory Panels
X
Firepots
5 years
3 years
7 years
3 years
10 years
1 year
X
Burners, Logs & Refractory
Limited
Lifetime
1 year
X
Firebox & Heat Exchanger
90 Days
X
X
X
X
X
Castings & Baffles
X
X
Firebox, HHT Chimney,
Termination & Heat
Exchanger
X
X
X
See Conditions, Exclusions, and limitations.
X
All Replacement Parts
9-01-08
CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY
• This warranty applies to the original owner and is transferable up to two years from date of purchase to the new homeowner,
provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its
original place of installation.
• The maximum amount recoverable under this warranty is limited to the purchase price of the product.
• In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.
• Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home is
not covered under this warranty.
Page 1 of 2
84
4021-645A 09-01-08
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
D. Limited Lifetime Warranty (continued)
• This limited warranty does not extend to or include surface finish on the appliance or terminations, door gasketing, glass
gasketing, glass discoloration, firebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion
on any of the metal surfaces, cast iron components, baffles, firepots, doors, or firebox area are not covered by this
warranty.
• Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to this
noise are not covered by this warranty.
• HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or maintenance
of the appliance not in accordance with the installation instructions; operating instructions and the listing agent identification
label furnished with the appliance; (2) installation which does not comply with local building codes; (3) shipping, improper
handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate
ventilation or drafting caused by tight sealing construction of the structure or handling devices such as exhaust fans or forced
air furnaces or other such causes; (5) use of fuels other than those specified in the operating instructions; (6) installation
or use of components not supplied with the appliance or any other components not expressly authorized and approved
by HHT; and/or (7) modification of the appliance not expressly authorized and approved by HHT in writing.
• This warranty does not apply to non-HHT venting components, hearth components or other accessories used in conjunction
with the installation of this product.
• This warranty is void if the appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine,
or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or there is any
damage to the appliance or other components due to water or weather damage which is the result of, but not limited to,
improper chimney or venting installation.
• HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship during
the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the defective
component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.
• Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not
apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state.
• EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE
WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF
THE WARRANTY SPECIFIED ABOVE.
This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all
warranties currently in existence.
If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide necessary
parts or components, contact the nearest authorized HHT dealer or supplier.
Page 2 of 2
4021-645A 09-01-08
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08
85
E. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843,
5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237,
5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860,
6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039,
6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
Printed in U.S.A. - Copyright 2008
86
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. K • 9/08