WASHING MACHINE
USER’S MANUAL
ESV80HA
BEFORE USING THE WASHING MACHINE, PLEASE READ THE
INFORMATION IN THIS MANUAL.
CONTENTS
CHAPTER-1: TECHNICAL SPECIFICATIONS
CHAPTER-2: BEFORE USING WASHING MACHINE
Safety warnings
Recommendations
CHAPTER-3: SETTING UP
.....
Removing transport safety screws
Adjusting adjustable stays
Electrical connection
Water inlet connection
Water discharge connection
CHAPTER-4: PRELIMINARY PREPARATION FOR
WASHING
CHAPTER-5: CONTROL PANEL
Detergent drawer
Programme knob
Electronic display
CHAPTER-6: OPERATING YOUR MACHINE
Selecting programme
Auxiliary functions
Starting the programme
Adding/Removing laundry
Child lock
Cancelling programme
Finishing programme
CHAPTER-7: ELECTRONIC DISPLAY WARNING SYMBOLS
Warning of water cut-off/low mains water pressure
Warning of clogged pump fitler
CHAPTER-8: MAINTENANCE AND CLEANING OF YOUR
MACHINE
CHAPTER-9: PRACTICAL INFORMATION
CHAPTER-10: TROUBLESHOOTING
CHAPTER-11: AUTOMATIC FAULT WARNINGS AND
WHAT TO BE DONE
CHAPTER-12: SAVING ENERGY AND WATER
2
3
5
5
6
7
7
9
10
10
11
12
15
16
17
18
19
19
19
28
29
30
31
32
33
33
34
35
40
42
47
49
CHAPTER -1: TECHNICAL SPECIFICATIONS
2
3
4
1
1.Detergent drawer
2. Upper tray
3.Programme knob
4.Electronic display
5.Door
6.Pump filter cover
5
6
8
9
10
7
7
7. Transport safety
screws
8.Power cable
9. Discharging hose
10.Water inlet valve
7
7
3
CHAPTER -1: TECHNICAL SPECIFICATIONS
Operating voltage / frequency (V/Hz)
(220-240) V ~/50Hz
10
Total current (A)
Maximum: 1 MPa
Minimum: 0.1 MPa
Water pressure (MPa)
2200
Total power (W)
Maximum dry laundry capacity (kg)
8
Maximum spin speed (rev / min)
1400
Number of washing programmes
15
Dimensions
(Height x Width x Depth) (mm)
845 x 597 x 587
4
CHAPTER -2: BEFORE USING YOUR WASHING MACHINE
SAFETY WARNINGS
SAFETY WARNINGS
Do not use double adaptors, power boards or extension cords.
Do not use if the power cord or plug is damaged.
Never pull the cable when unplugging.
Do not plug-in or pull out the plug from the receptacle with wet
hands to prevent electric shock. Never touch the machine when
wet.
Never open the detergent compartment when the appliance is
running.
Never force the door open when the washing machine is running.
Do not touch discharging hose and water during discharging as the
appliance may reach high temperatures when running.
In case of breakdown, unplug the appliance first and then turn the
water off. Do not attempt to repair by yourself, consult authorized
service.
Remember that packaging materials may be dangerous for
children. Keep the packaging materials away from children or
dispose of them.
Do not allow your children play with the washing machine which is
an electrically-driven appliance.
Keep your pets away from your machine.
Your machine should only be used by adults in line with the
information provided in this user’s manual.
Your machine is designed to be used domestically.
Do not place your machine on carpet and suchlike grounds that
could block ventilation of the base.
Do not keep inflammable liquids near your machine.
5
CHAPTER -2: BEFORE USING YOUR WASHING MACHINE
SAFETY WARNINGS / RECOMMENDATIONS
You must remove the transport screws of your machine before the
first usage. Faults occurring in a machine operated with the
transport screw fitted shall be out of scope of warranty.
Do not put discharging hose of your machine in a vessel or bucket.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of expererience and knowledge. Unless they have been given
supervision or instruction concerning the use of this appliance by a
person responsible for their safety.
Keep pets away from the washing machine.
RECOMMENDATIONS
It is recommended to perform the first washing operation in
95 White Cotton programme and without laundry by inserting
½ measure of detergent in 2nd compartment of the detergent
drawer.
As detergent or softener exposed to air for a long time may cause
residues, put your detergent or softener in the detergent drawer in
the beginning of each washing.
It is recommended that you wash only extremely dirty laundry in
prewashing programme.
The amount of laundries you put in your washing machine should
not exceed the maximum amount indicated. By this way, your
machine shall run the most efficiently.
Some water may be left in your machine due to quality control
tests carried out during production. This will not damage your
machine.
After completing your washing for the day, it will help to keep the
machine smelling fresh if you leave the door slightly open to allow
the flow of fresh air.
6
CHAPTER -3: SETTING UP
REMOVING TRANSPORT SAFETY SCREWS
Before operating your washing machine, you must remove the
transport safety screw on the rear side of the machine.
For this reason, transport safety screws shall be loosened by being
rotated in counter-clockwise using an appropriate spanner.
7
CHAPTER -3: SETTING UP
REMOVING TRANSPORT SAFETY SCREWS
Transport screws shall be removed by pulling out.
Fit the plastic transport screw taps delivered in accessories bag to the
places where transport screws have been removed.
The transport safety screws should be stored to be used in case of a
transportation.
Do not operate the machine with the transport screws fitted. Damage
to the machine is likely to occur.
8
CHAPTER -3: SETTING UP
ADJUSTING ADJUSTABLE STAYS
Do not install your machine on a carpet or suchlike grounds.
To ensure silent and vibration-free operation of your machine, it
should be placed on a non-sliding and firm ground.
Loosen the plastic locking nut.
Adjust the feet upward and downward by rotating them.
Never put cardboard, wood or suchlike materials under your
machine if you are intending to stabilize the distortions on the
ground.
When cleaning the ground, on which your machine rests, be
careful not to disorder stays stabilization.
Adjust the feet, so that the machine is level and all feet are
touching the floor amd the machine does not rock. Then adjust up
the “locking nut”
9
CHAPTER -3: SETTING UP
ELECTRICAL CONNECTION / WATER INLET CONNECTION
Electrical connection
Your washing machine is set to 220-240V and 50Hz.
Water inlet connection
Your machine may have either a single inlet (cold) or double water
inlets (cold/hot) based on its specifications. White-capped hose
should be connected to cold water inlet and red-capped hose to
hot water inlet (applicable for machines with double water inlets).
To eliminate water leakages in points of contact, 1 or 2 washers
are provided in the hose package (applicable for machines with
double water inlets). Fit these washers to the ends of new water
inlet hoses on the side of the tap.
Connect the white-elbow end of the water inlet hoses to the whitefiltered water inlet valve on the rear side of the machine and the
red-elbow end to red-filtered one (applicable for machines with
double water inlets). Tighten plastic parts of the junctions using
your hand.
Flow of water with pressure of 0.1-1 Mpa will allow your machine to
operate more efficiently (0.1 Mpa pressure means that more than 8
litres of water will flow through a fully-opened tap per one minute).
Ensure that new water inlet hoses are not folded, broken, crushed
or their dimensions are not altered.
Connect new water inlet hoses to a ¾ , threaded tap.
If your machine has double hot water inlets, the temperature of hot
water inlet should not exceed 70°C.
10
CHAPTER -3: SETTING UP
WATER INLET CONNECTION / WATER D SCHARGE
CONNECTION
Water discharge connection
Ensure that water discharge hose is not folded, twisted, crushed or
elongated.
Water discharge hose can be fitted minimum 60 cm and maximum
100 cm above the ground.
The end of water discharge hose can be attached to dirty water
discharge hole.
Never attempt to extend the water discharge hose by jointing.
Do not put discharging hose of your machine in a vessel or,
bucket.
Max. 100 cm.
Max. 60 cm.
11
CHAPTER-4: PRELIMINARY PREPARATION FOR WASHING
Separate your laundries according to their types (cotton, synthetic,
sensitive, woollen, etc.), their temperatures (cold, 30°, 40°, 60°,
90°) and degree of contamination (slightly stained, stained, highly
stained).
Never wash your coloured and white laundries together.
Wash your coloured laundries separately in the first washing as
they may colour bleed.
Ensure that there are no metallic materials on your laundries or in
the pockets; if so, take them out.
WARNING: Faults that will emerge in case of penetration of
foreign substances into your machine are not included within the
scope of warranty.
Remove the metallic or plastic hooks of tulle curtains or curtains or
place them in a washing net or bag and then muzzle them.
Zip-up and button up your laundries.
Turn inside out pants, knitwear, t-shirt and sweat suit.
Normal washing
Maximum
washing
temperature is
90°C
Maximum
washing
temperature is
60°C
Maximum
washing
temperature is
30 °C
Hand washing
No washing
12
CHAPTER-4: PRELIMINARY PREPARATION FOR WASHING
Open the door of your machine.
Spread your laundries in your machine.
Note: Maximum loading capacity may vary based on the
laundry type you will wash, degree of contamination and the
programme you have chosen. Do not exceed maximum dry
loading capacity indicated in the programme table for
washing programmes.
You can take the following table of weights as an example.
LAUNDRY TYPE
WEIGHT (gr)
200
500
1200
700
200
100
250
Towel
Linen
Bathrobe
Quilt cover
Pillow slip
Underwear
Tablecloth
Put the laundries separately.
Ensure that no laundry is stuck between the cover and bellow seal
when closing the door of your machine.
Close the door of your machine properly; otherwise your machine
will not start the washing operation.
13
CHAPTER-4: PRELIMINARY PREPARATION FOR WASHING
The amount of detergent you will put in your machine will depend on
the following criteria:
Your detergent requirement will be based on the degree of
contamination of your laundries. Do not prewash your less stained
laundries and put your slight amount of detergent in the 2nd
compartment of the detergent drawer.
For your much stained laundries, select a programme including
prewashing, and put ¼ of the detergent you will put in the
detergent drawer in the 1st compartment of the detergent drawer
while putting the remaining ¾ of it into 2nd compartment.
Use detergents produced for front loading machines. The amount
of detergent you will use for your laundries is printed on the
detergent package.
The higher the degree of hardness of the water the more detergent
you will use.
The amount of the detergent you will use will increase as the
amount of your laundries increase.
Put the softener in the softener compartment in the detergent
drawer. Do not exceed the MAX level. Otherwise, softener will flow
into washing water through flushing and stain your laundry.
Softeners with high density are required to be thinned to a degree
before being put in the drawer. Because high-density softener will
clog the flush and avoid the flow of the softener.
You can use your liquid detergents in all programs without
prewashing. For this, fit liquid detergent level plate in the
accessories bag into 2nd compartment of the detergent drawer and
set the amount of liquid detergent according to the levels on this
plate. Remember to detach the liquid detergent plate.
14
1-Detergent drawer
2-Programme knob
3-Electronic display and auxiliary functions
1
2
3
CHAPTER 5: CONTROL PANEL
15
CHAPTER 5: CONTROL PANEL
DETERGENT DRAWER
E
D
B
A
C
A. Prewashing compartment
B. Main washing compartment
C. Softener compartment
D. Siphon cover
E. Liquid level detergent plate
16
CHAPTER 5: CONTROL PANEL
PROGRAMME KNOB
Select the programme you wish to wash your laundries through
programme knob. You may set the programme selection
operation by rotating the programme knob in both direction.
Ensure that the programme knob is exactly on the programme
you want to select.
17
CHAPTER 5: CONTROL PANEL
ELECTRONIC DISPLAY
1-Adjusting button for revolution speed
2-Adjusting button for temperature of washing water
3-Auxiliary function prewash
4-Auxiliary function for rapid wash
5-Auxiliary function for easy ironing
6-Auxiliary function for delay timer
7-Start/Pause button
8-Electronic display
On the electronic display, you may view washing water temperature,
spin speed of your machine, the amount time your machine will
continue washing, the auxiliary functions you have selected and
whether the door of your machine is locked or not. Furthermore,
electronic display will warn you by means of fault symbols on the
display when a fault occurs on your machine and notify you of the
completion of the washing programme by revealing expression of
“END” on the display as soon as the washing programme you have
selected has finished as well.
18
CHAPTER 6: OPERATING YOUR MACHINE
Plug your machine in.
Turn on the tap.
Open the machine door.
Load your laundries in your machine.
Push the door of your machine until hearing the locking sound to
close it.
Put detergent and softener in the detergent drawer.
First washing operation
Some water may be left in your machine due to quality control test
carried out during production. To dispose of this water, it is
recommended to perform the first washing operation in 1st programme
and without laundry by inserting ½ scale of detergent in 2nd
compartment of the detergent drawer.
Selecting programme
Select the convenient programme for your laundries on the
programme table.
Auxiliary functions
Before starting the programme, you can optionally select an auxiliary
function.
Press on the button of auxiliary function you like to select.
If auxiliary function symbol on electronic display flashes
continuously, the auxiliary function you have selected will be
activated.
If auxiliary function symbol on electronic display blinks, the
auxiliary function you have selected will not be activated.
Reason for non-activation:
-The auxiliary function you want to use in the washing programme you
have selected is not applicable.
-Your machine has passed over the stage, during which the auxiliary
function you like to select would be implemented.
-It is not compatible with an auxiliary function you have selected
previously.
19
CHAPTER 6: OPERATING YOUR MACHINE
Half-load detection system
Your machine features a half-load detection system. In case you put
approximately half or less amount of laundries of maximum laundry
capacity in your machine, your machine will run so as to save washing
time, water consumption and energy in some programmes (White
cotton 95°, Colorfast cotton 60°, Non colorfast cotton 40°). When halfload function is active, the machine can complete the programme you
have set in a shorter time.
Twinjet system
Detergent water in your machine will be circulated with 2 water
injection mechanisms and a mixing system via twinjet system.
Circulated detergent water will be injected over your laundry, which
allows a better washing performance.
Twinjet system will help you wash higher amount of laundry in a
shorter time with a better washing performance, less energy and water
consumption.
20
CHAPTER 6: OPERATING YOUR MACHINE
PROGRAM TABLE
TEMPERATURE
(°C)
MAXIMUM
AMOUNT OF
DRY
LAUNDRY
(kg)
DETERGENT
COMPARTMENT
1-COTTON
95
8
2
2-COTTON
60
8
2
3-COTTON
40
8
2
4-SYNTHETICS
60
3,5
2
5-SILK
6-WOOL
30
40
2,5
2,5
2
2
7-RINSE
-
8
-
8-SPIN
-
8
-
9-HAND W ASH
30
2,5
2
10-SPORTS WEAR
11-MIX WASH
12-SHIRTS/
BLOUSES
30
30
3,5
3,5
2
2
Very dirty synthetic or synthetic-mixed textiles. (Nylon socks, shirts, blouses, syntheticincluding trousers etc.)
Less dirty silk-mixed laundries with machine wash labels.
Woollen laundries with machine wash labels.
If you want to additionally rinse your laundries upon completion of washing operation,
you may use this programme for any kind of laundries.
If you want to additionally wring your laundries upon completion of washing operation,
you may use this programme for any kind of laundries.
Sensitive and woollen laundries with non-machine wash label recommended to be
washed by hand.
Sportswear.
Dirty cotton, synthetic, colour and flax textiles can be washed together.
60
4
2
Dirty cotton, synthetic and synthetic-mixed shirts and blouses can be washed together.
13-HYGIENE
30
5
2
14-DAILY 60 min.
60
4
2
15-SUPER RAPID
12 min.
-
2
2
PROGRAMME
LAUNDRY TYPE
Very dirty cotton and flax textiles. (Underwears, linen, tablecloth, (towel maximum 4 kg),
bedclothes, etc.)
Dirty cotton and flax textiles. (Underwears, linen, tablecloth, (towel maximum 4 kg),
bedclothes, etc.)
Normally soiled cotton clothes (Underwears, linen, tablecloth, (towel maximum 4 kg),
bedclothes, etc.)
For European Countries only. This function requires washing detergents that meet
European IEC Standards.
You can wash your dirty cotton, colour and flax textiles at 60°C in 60 minutes.
You can wash your slightly dirty cotton, colour and flax textiles in 12 minutes that is a
short period.
Note: As the washing period is short, less amount of detergent is required to be used
compared to other programmes. The programme period will increase if your machine
detects an unstable load. You can open the door of your machine 2 minutes after the
completion of washing operation. (The duration of 2 minutes required to open the door
of your machine is not included in the washing period.)
Program duration, energy consumption and water consumption values may vary according to wash load weight and type, selected extra functions, tap water and ambient
temperature
21
CHAPTER 6: OPERATING YOUR MACHINE
AUXILIARY FUNCTIONS
1-Spin speed selection and auxiliary function of soaking
You can set the spin speed for your laundry via spin speed setting
button.
When you select a new
programme, the maximum spin
speed of the programme you have
selected will be viewed on the
display of spin speed.
You can gradually reduce the spin
speed between cancel spinning (-) options through the maximum
spinning speed of the programme
selected by pressing spin speed
setting button.
If you have skipped the spin speed you want to set, you can re-switch
to the speed by keeping the spin speed setting button pressed.
If you do not remove your laundries upon completion of the
programme and you do not want them to wrinkle in your machine, you
can use the auxiliary function of soaking.
In programmes where auxiliary
function of soaking is an option, it
may be activated by pressing the
spin speed setting button once
more. You can see that it is active
when symbol
flashes on
electronic display.
22
CHAPTER 6: OPERATING YOUR MACHINE
AUXILIARY FUNCTIONS
If this function is selected, your laundries will be soaked in the latest
rinsing water. When your machine soaks your laundries in the latest
rinsing water, symbol
will blink on electronic display.
If you want to take your laundries out, press on “Start / Pause” button.
Your machine will empty the water in it and finish the programme
without spinning.
If you want to spin your laundries again:
a) You can select spin speed by using the spin speed setting
button when your machine is soaking your laundries in the
latest rinsing water. If you want to take your laundries out,
press on “Start / Pause” button. Your machine will empty the
water in it and finish the programme after spinning your
laundries through the spinning speed you have selected.
b) Switch the programme knob to 0. Select spin programme on
programme knob. You can optionally reduce the spin speed.
You can start your machine by pressing on Start/Pause button.
Your machine will finish the programme after spinning your
laundries in the spinning speed you have selected.
23
CHAPTER 6: OPERATING YOUR MACHINE
AUXILIARY FUNCTIONS
2-Washing water temperature selection
You can select the washing water temperature with the washing water
temperature adjustment button.
Whenever you select a new
programme, the maximum
washing water temperature is
shown on the washing water
temperature display.
You can gradually decrease the
washing water temperature
between the maximum
temperature and cold washing (--)
by pressing washing water
temperature adjustment button.
If you have missed the washing water temperature setting you wanted,
you can return to the intended temperature by continuously pressing
the washing water temperature adjustment button.
24
CHAPTER 6: OPERATING YOUR MACHINE
AUXILIARY FUNCTIONS
3-Auxiliary function prewash
Very dirty laundry can be prewashed before the main wash
with this function. When using this
function, you should put detergent
in front washing compartment of
the detergent drawer.
4-Auxiliary function for rapid wash
This auxiliary function will enable
the washing duration of your
laundries that are not very dirty to
be shortened. In case you put
half of or less than half of the
laundry capacity of the washing
programme you have selected in
your machine, your machine will
detect this event thanks to
automatic half-load detection
system, and the programme you have selected will wash your
laundries in a shorter time to consume less energy and water. If your
machine detects half load, symbol
will automatically flash on
electronic display. To cancel it, pressing on the auxiliary function of
quick washing for once will be enough. However, selection of auxiliary
function of quick washing is not possible in course of the same
washing operation.
5-Auxiliary function for easy ironing
You can enable your laundries to
be taken out less wrinkled as the
washing operation is completed
by employing this auxiliary
function.
25
CHAPTER 6: OPERATING YOUR MACHINE
AUXILIARY FUNCTIONS
6-Auxiliary function for delay timer
By using this auxiliary function,
you can let your machine start
washing after half an hour to 23
hours. For time of use electricity
customer, this allows you to use
your electricity at a cheaper tariff
rate.
To use auxiliary function of delay timer:
- Press time delay button once.
- Expression of “0.5h” will appear on the display.
- Press on time delay button until the time, on which you want washing
operation to be started.
- To activate the time delay you have selected in the programme, you
may press on any auxiliary function button you like except
“Start/Pause” button.
Intervals of delay timer is half an hour for the first 2 hours, 1 hour for 3
hours to 23 hours.
If you have skipped the time delay you want to set, you can go back to
the time desired by keeping pressed on delay timer button.
If you want to cancel the delay timer, you are required to press the
delay timer button once.
To run delay timer function, your machine is required to be operated
by pressing on Start/Pause button. As soon as you start your machine,
the count down process will start on the electronic display based on
the delay period you have selected.
26
CHAPTER 6: OPERATING YOUR MACHINE
AUXILIARY FUNCTIONS
7-Anti-Allergic auxiliary function
In the programmes where this
auxiliary function is active, your
machine will perform an extra
rinsing operation on your
laundries prior to latest rinsing
operation.
Note: Anti-Allergic auxiliary function is selected automatically only in
Hygiene programme.
27
CHAPTER 6: OPERATING YOUR MACHINE
STARTING THE PROGRAMME
Start/Pause button
By pressing on Start/Pause
button, you may start the
programme you have selected or
suspend a running programme. If
you switch your machine to pause
mode, the electronic display will
blink.
When you start your machine, the following symbols for the
programmes you have selected will be available on electronic display.
- Temperature of washing water
- Spin Speed
- If you have selected, symbols of auxiliary functions
- Programme ending time or programme delay time based on your
selection
- Symbol of open or locked door
Note: Symbol for open door flashing on electronic display will go off
and symbol for locked door will flash approximately 1 minute after you
start your machine by pressing Start/pause button.
Open door
Locked door
28
CHAPTER 6: OPERATING YOUR MACHINE
ADDING/REMOVING LAUNDRY
Laundry adding to / removing from the machine
If you want to add or remove laundries when your machine is running:
- Switch your machine to pause mode by pressing on Start/Pause
button.
has changed on the
- After a while, if you see that the symbol
display, this means that the door of your machine can now be opened.
When you see symbol
on electronic display, you can either add or
remove laundries after opening the machine door.
blinks on the electronic display, it means that your
Note: If symbol
machine cannot carry out the operation of laundry adding or removing
as your machine has passed the steps in question.
- Upon completion of laundry adding or removing function, close the
door of your machine and press on Start/Pause button.
- Your machine will continue to wash after locking the door of your
machine.
- Symbol
will flash on electronic display.
29
CHAPTER 6: OPERATING YOUR MACHINE
CHILD LOCK
Child lock
To avoid programme flow from being affected if programme knobs are
pressed or programme knob is turned when performing washing
operation in your machine, child lock is available. Child lock will be
activated by pressing on both auxiliary functions of rapid wash and
easy ironing at the same time in excess of 3 seconds.
Symbol
will flash on the electronic display when activated.
If any button is pressed while child lock is active, symbol
on the electronic display.
will blink
When any of the programmes are running and child lock is active, if
another programme is selected after programme knob is switched to 0
position, the programme already running will resume.
To deactivate it, press on the same buttons for more than 3 seconds.
When child lock is deactivated, symbol
will go off.
30
on the electronic display
CHAPTER 6: OPERATING YOUR MACHINE
CANCELLING PROGRAMME
Cancelling programme
If you want to cancel any programme running:
- Switch the programme knob to 0.
- Your machine will stop the washing operation and the programme will
be cancelled.
- To get rid of the water accumulated in the machine switch the
programme knob to any programme.
- Your machine will perform the necessary discharge operation and
cancel the programme.
- You can run your machine by selecting a new programme.
31
CHAPTER 6: OPERATING YOUR MACHINE
FINISHING PROGRAMME
Finishing programme
- Your machine will stop by itself as soon as the programme you have
selected finishes.
-Expression of “END” will flash on the electronic display.
Note: Within 2 minutes after the programme has finished, your
machine will extinguish the electronic display to save energy. It will reflash when any auxiliary function button is pressed.
- If you see that the symbol indicating that the door can be opened
flashes on the electronic display, you can open the door of your
machine and remove the laundry.
- Leave the door of your machine open to allow the inner part of your
machine to dry after removing your laundries.
- Switch the programme knob to 0.
- Switch off the power at the mains.
- Turn the tap off.
32
CHAPTER -7: ELECTRONIC DISPLAY WARNING SYMBOLS
WARNING OF WATER CUT-OFF / LOW MAINS WATER
PRESSURE
If symbol
flashes on the electronic display:
- Tap may be closed. Check.
- Mains water may be cut-off. Check. If so, switch the programme knob
to position 0. You can select a programme and run your machine after
the mains water is supplied.
- Mains water pressure may be low. Check.
- Water inlet hose may be twisted. Check.
- Water inlet hose may be clogged. Clean water inlet hose filters. (*)
- Valve inlet filter may be clogged. Clean the valve inlet filters. (*)
(*) See the chapter regarding maintenance and cleaning of your
machine.
33
CHAPTER -7: ELECTRONIC DISPLAY WARNING SYMBOLS
WARNING OF CLOGGED PUMP FILTER
If symbol
flashes on the electronic display:
- Pump filter may be clogged. Clean the pump filter. (*)
- Discharging hose may be clogged or twisted. Check the discharging
hose.
(*) See the chapter regarding maintenance and cleaning of your
machine.
34
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR
MACHINE
Unplug your machine.
Turn the tap off.
WATER INLET FILTERS
Filters to avoid dirt and foreign substances in the water from
penetrating into the machine filters are available both on the side of
the tap and on the ends of water valves along the water inlet hose of
your machine. If your machine cannot intake sufficient amount of water
despite the tap being open, these filters should be cleaned.
Detach the water inlet hoses.
Remove the filters on water inlet valves using pliers and then clean
it with a brush in water.
Disassemble the filters on the tap side of water inlet hoses
manually and clean it.
Having the filters cleaned, you can fit them in the same way
reversely.
CAUTION: Filters of water inlet valves may be clogged due to
contaminated water or lack of necessary maintenance or valves
may be broken down, causing water leaking into your machine
continuously.
35
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR
MACHINE / PUMP FILTER
A filter system which avoids small items (i.e. coins) from entering into
the pump during water discharging is carried out by your machine after
completing washing to prolong the lifecycle of your pump. It is
recommended that you clean your pump filter once in 2 months. To
clean the pump filter:
Depress the lug downwards, to uncover the pump section of the
toe board and pull it towards yourself and extract it.
Before opening the filter cover, settle a vessel in front of the filter
cover to prevent the water remained in the machine from flowing
on the ground.
Loosen the filter cover in counter-clockwise and then empty water.
Clean the foreign materials in the filter.
Check whether the pump rotates with your hands.
36
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR
MACHINE / PUMP FILTER
After cleaning the filter, fit the filter cover by rotating it clockwise.
Fit the pump section of the toe board.
Remember that water will leak if you do not fit the filter cover
properly.
You can use the pump section of the toe board for discharging
slight amount of water remaining in the pump of your machine.
WARNING!
As water in the pump may be hot, wait until it cools down.
37
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR
MACHINE / DETERGENT DRAWER
Your detergents may deposit residue in the detergent drawer and
housing of detergent drawer over time. To clean the residue formed,
disassemble the detergent drawer in particular periods. To eject the
detergent drawer:
Pull the detergent drawer up to the end
Keep on pulling by depressing on the flush cover in the detergent
drawer already being pulled up to the end and then unsettle the
detergent drawer.
Flush it using a brush.
Collect residues in the housing of the detergent drawer without
dropping them inside the machine.
To assemble the detergent drawer after drying it using a towel or
dry cloth, resettle the detergent drawer by depressing on the flush
cover and fit it by pushing forward.
Do not wash your detergent drawer in dishwasher.
38
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR
MACHINE / SIPHON PLUG / BODY / DRUM
Siphon plug
Disassemble the detergent drawer. Disassemble the flush stopper and
clean the softener residues completely. Refit the flush stopper after
cleaning it. Check whether it has settled properly.
Body
Clean the outer body of your machine with warm water and a noninflammable cleaning agent that will not abrade the body of your
machine. After rinsing with some water, dry it using a soft and dry
cloth.
Drum
Do not leave metallic objects such as needles, paper clips, coins, etc.
in your machine. These objects will lead to formation of rust stains in
the drum. To clean such rust stains, use a non-chlorine cleaning agent
and follow the instructions of manufacturers of the cleaning agent.
Never use steel wool or similar hard objects for cleaning rust stains.
39
CHAPTER -9: PRACTICAL INFORMATION
Alcoholic drinks: Spotted areas should initially be washed
using cold water, and then be wiped with glycerine and
water and rinsed with vinegar-mixed water.
Shoe shine: Spots should be rubbed out gently without
damaging the cloth and be scrubbed and rinsed with
detergent. If not removed, it should be scrubbed using the
mixture obtained by adding 1 measure of alcohol (96 ) into 2
measure of water, and then be washed with warm water.
Tea and coffee: Stretch the spotted area of your laundry
throughout the opening of a vessel, and pour hot water as
much as the type of your laundry can resist If it is still a
stubborn stain then use bleach, if your laundry permits it.
Chocolate and cocoa: After submerging your laundry in
cold water and rubbing it using soap or detergent, wash it in
temperature that fabric type of your laundry can resist. In
case oil stain is still visible, wipe with oxygen water (3%).
Tomato paste: After rubbing out the dried substances
without damaging your laundry, submerge it in water for 30
minutes, and then scrub and wash it with detergent.
Bouillon-egg: Remove dried spot residues on your laundry,
and then wipe it with a sponge or soft cloth submerged in
cold water previously. Scrub with detergent, wash with
diluted bleach.
Grease and oil stains: Firstly, wipe the residues. Scrub the
spot with detergent and wash it with warm soapy water.
Mustard: Apply glycerine on the spotted area. Scrub with
detergent and wash. If spot cannot be removed, then wipe
with alcohol. (For synthetic and colour fabrics, a mixture of 1
measure of alcohol and 2 measures of water should be
used)
40
CHAPTER -9: PRACTICAL INFORMATION
Blood stain: Submerge your laundries in cold water for
30 minutes. If the stain is not removed, then submerge
in a mixture of water and ammoniac (3 spoons of
ammoniac in 4 litres of water) for 30 minutes.
Cream, ice cream and milk: Submerge your laundry in
cold water and scrub the spotted area with detergent. If
the spot is not removed, apply bleacher to the extent
suitable for your laundries. (Do not use bleacher for
colour laundries.)
Mould: Mould stains should be cleaned as soon as
possible. Stain should be washed with detergent water,
nevertheless if it cannot be removed, it should be wiped
with oxygen water (3%).
Ink: Subject the spotted area to running water and wait
until the flow of inked water ends. Then, wipe it with
lemon-added water and detergent, and wash it after
allowing 5 minutes.
Fruit: Stretch the spotted area of your laundry
throughout the opnening of a vessel, and pour cold
water on it. Do not pour hot water on the spot. Wipe with
cold water and apply glycerine. Allow 1-2 hours, wipe
with a few drops of white vinegar, and rinse it.
Grass stain: Wipe the stained part with detergent. If the
laundries permit using bleach, wash with bleach. Wipe
your woollen laundries with alcohol. (For colour fabrics,
a mixture of 1 measure of pure alcohol and 2 measures
of water)
Oil paint: Spot should be removed by applying thinner
before drying. Then, it should be wiped with detergent
and washed.
Burn stain: If your laundry is suitable for applying
bleach, you can add bleacher into washing water. For
woollen fabrics, a cloth previously submerged in oxygen
water should be covered over the stain, and it should be
ironed after putting a dry cloth on this cloth. It should be
washed after being rinsed properly.
41
CHAPTER -10: TROUBLESHOOTING
All repairing operations required for your machine should be carried
out by authorised service, personnel If your machine requires a repair
or if you cannot remove the fault by the help of the information
provided as follows:
Unplug your machine.
Turn the tap off.
Contact the nearest authorised service technician.
FAULT
Your machine does
not start.
POSSIBLE CAUSE
It is not plugged.
Fuses out of order.
Electricity cut-off.
Start/pause button
not pressed.
Programme knob on
position 0.
REMOVING
METHODS
Plug it.
Replace the fuses.
Check mains power.
Press on start/pause
button.
Switch the
programme knob to
the desired position.
The machine door
Close the machine
not completely
door.
closed.
Your tap is turned
Turn your faucet on.
off.
Water inlet hose may Check water inlet
be twisted.
hose.
Clean water inlet
Water inlet hose
Your machine does
clogged.
hose filters. (*)
not intake water.
Valve inlet filter
Clean the valve inlet
clogged.
filters. (*)
The machine door
Close the machine
not completely
door.
closed.
(*) See the chapter regarding maintenance and cleaning of your
machine.
42
CHAPTER -10: TROUBLESHOOTING
FAULT
POSSIBLE CAUSE
Discharging hose
clogged or twisted.
Your machine does
not discharge water.
Pump filter clogged.
Laundries settled in
the machine nonhomogeneously.
The stays of your
machine not
adjusted.
Safety assembly
fitted for transport
not disassembled.
Less amount of
laundries in the
appliance.
REMOVING
METHODS
Check the
discharging hose.
Clean the pump
filter. (*)
Spread your
laundries in the
machine properly
and homogeneously.
Adjust the stays of
your machine. (**)
Disassemble the
safety assembly of
your machine. (**)
This will not block
operation of your
machine.
Do not put laundries
Your machine
more than the
Your machine
overloaded with
amount
vibrates.
laundries or
recommended and
laundries settled
settle the laundries in
non-homogeneously the machine
homogeneously.
Prevent your
machine from resting
on hard surfaces.
Your machine rests
When settling your
on a hard surface.
machine, leave 2 cm
space between it and
wall or hard
surfaces.
(*) See the chapter regarding maintenance and cleaning of your
machine.
(**) See the chapter regarding installation of your machine.
43
CHAPTER -10: TROUBLESHOOTING
FAULT
POSSIBLE CAUSE
Excessive amount of
detergent used.
Excessive foam is
formed in the
detergent drawer.
Wrong detergent
used..
The contamination
degree of your
laundries does not
match the programme
you have chosen.
Unsatisfactory
washing result.
Amount of detergent
used insufficient.
Laundries in excess
of maximum capacity
put in your machine.
44
REMOVING
METHODS
Press on Start/Pause
button. To eliminate
foam formation, mix a
spoon of softener with
half litres of water,
and pour the mixture
in the detergent
drawer. After 5-10
minutes, press on
Start/Pause button
again. In next
washing operation,
decide the dose of
detergent as required.
Use detergents
produced only for
automatic washing
machines in your
machine.
Select the programme
appropriate for the
contamination degree
of your laundries. (see
programme table)
Adjust the amount of
detergent based on
the amount and
contamination degree
of your laundries.
Load your machine
with laundries,
amount of which will
not exceed maximum
laundry capacity
CHAPTER -10: TROUBLESHOOTING
FAULT
POSSIBLE CAUSE
Water being hard.
(Dirty, hard, etc.)
Unsatisfactory
washing result.
Laundries distributed
in your machine nonhomogenously.
As soon as the
machine is loaded
with water, water
discharges.
No water appears in
the drum during
washing.
The end of water
discharging hose is
too low for the
machine.
No fault. Water in the
non-visible part of the
drum.
REMOVING
METHODS
Adjust the amount of
detergent based on
the instruction of
detergent
manufacturer.
Spread your laundries
in the machine
properly and
homogeneously.
Set the water
discharging hose on
appropriate height.
(**)
-
Perform an extra
rinsing by setting your
machine to “Rinsing”
Laundries have
programme, or clean
detergent residues on
the spots using a
them.
brush after your
laundries dries.
Apply the maximum
amount of detergent
The reason for this
instructed by the
Grey spots appear on
spots may be oil,
detergent
the laundries.
cream or ointment.
manufacturer in the
next washing
operation.
(**) See the chapter regarding installation of your machine.
Non-dissolving
particles of some
detergents may
adhere to your
laundries as white
spots.
45
CHAPTER -10: TROUBLESHOOTING
FAULT
POSSIBLE CAUSE
Wringing operation is
not performed or
runs late.
No fault. Unbalanced
load control system
has been activated.
46
REMOVING
METHODS
Unbalanced load
control system will
try to spread your
laundries
homogeneously.
Spinning operation
will start after
spreading your
laundries. Put your
laundries in the
machine
homogeneously in
the next washing
operation.
CHAPTER -11: AUTOMATIC FAULT WARNINGS AND WHAT
TO BE DONE
Your machine is equipped with the systems which are capable of both
taking necessary precautions and warning you in case of any
breakdown by means of continuous self-checking during washing
operations.
TROUBLE
CODE
POSSIBLE
FAULT
WHAT TO DO
E01
The door of
your machine
is left open.
Close the machine door. If your
machine persists to indicate
fault, turn off your machine,
unplug it and contact the
nearest authorised service
agent immediately.
E03
Pump is faulty
or pump filter is
clogged or
electrical
connection of
the pump is
faulty.
Clean the pump filter.
If the problem persists, contact
the nearest authorised service
agent. (*)
Your machine will discharge
water by itself. Pursuant to
Your machine
discharging operation, turn off
has excessive
your machine and unplug it.
E04
amount of
Turn off your tap and contact
water.
the nearest authorised service
agent.
(*) See the chapter regarding maintenance and cleaning of your
machine.
47
CHAPTER -11: AUTOMATIC FAULT WARNINGS AND WHAT
TO BE DONE
TROUBLE CODE
POSSIBLE
FAULT
Water cut-off
or low mains
water
pressure..
Pump is
faulty or
pump filter is
clogged or
electrical
connection
of the pump
is faulty.
48
WHAT TO DO
- Tap may be closed. Check.
- Mains water may be cut-off.
Check.
- If so, switch the programme
knob to position 0. You can
select a programme and run
your machine after the mains
water is supplied.
- Mains water pressure may
be low. Check.
- Water inlet hose may be
twisted. Check.
- Water inlet hose may be
clogged.
- Clean water inlet hose
filters. (*)
- Valve inlet filter may be
clogged.
- Clean the valve inlet filters.
(*)
If the problem persists,
unplug your machine, turn off
your tap and contact the
nearest authorised service
agent.
- Pump filter may be clogged.
Clean the pump filter. (*)
- Discharging hose may be
clogged or twisted. Check the
discharging hose.
If the problem persists,
contact the nearest
authorised service agent. (*)
CHAPTER -12: SAVING ENERGY AND WATER
Energy and water consumption may vary based on water pressure,
water hardness, water temperature, ambient temperature, laundry
amount, additional function selection, voltage fluctuations.
It will reduce energy and water consumption to use your machine
with the laundry capacity proposed for the selected programme,
wash your less dirty or daily laundries in short programmes, carry
out cleaning and maintenance periodically, use your machine in
convenient time intervals specified by electricity vendor.
49
DISPOSAL OF YOUR OLD MACHINE
This symbol on the product or package implies that the
product should not be treated as domestic waste.
Instead, it should be delivered to applicable waste
collection places recycling electrical and electronic
equipment. You will contribute to avoid potential
negative results regarding environment and human
health, which will arise due to wrong waste procedure
for the product by ensuring that this product is
annihilated properly. Recycling materials will help
natural resources be preserved. For more detailed
information regarding recycling of this product, please
contact local municipality, domestic waste management
service or the shop you have purchased the product.
52086488