Samsung SPC-2010 User manual

SYSTEM CONTROLLER
User Manual
SPC-2010
System Controller
User Manual
Copyright
©2012 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s
own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
 Design and specifications are subject to change without prior notice.
 The default password can be exposed to a hacking thread so it is recommended to change the
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible
for the user.
overview
IMPORTANT SAFETY INSTRUCTIONS
●
1. Read these instructions.
OVERVIEW
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety pu rpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety, If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
English _3
overview
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PROCUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT
THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
4_ overview
Please read the following recommend safety precautions carefully.
 Reference : Providing useful information for the user.
 Notice : If the instructions are not followed correctly damage to the goods or person
may occur.
 For safety please read this manual for the before using of goods and keep it in the safe place.
English _5
OVERVIEW
User’s Manual is a guidance book on how to use the product.
Below is a key to the following signs that are used in this manual.
●
 Do not Place this apparatus on an uneven surface.
 Do not install on a surface where it is exposed to direct sunlight, near heating
equipment or heavy cold area.
 Do not place this apparatus near.
 Do not attempt to service this apparatus yourself.
 Do not place a glass of water on the product.
 Do not install near any magnetic sources.
 Do not block any ventilation openings.
 Do not place heavy items on the product.
overview
CONTENTS
3
3
6
8
9
10
Important Safety Instructions
Contents
Key Features
What’s Included
System Controller at a Glance
INSTALLATION
13
Precautions
14
To Connect a RS-485/422 Device
19
19
24
Getting Started
Controlling the PTZ Camera
Controlling DVR
OVERVIEW
13
CONNECTING TO AN EXTERNAL
DEVICE
14
USING THE MENU
19
6_ overview
MENU SETTING
32
32
34
35
Specifications
Troubleshooting
Product Overview
OVERVIEW
APPENDIX
PTZ setting
DVR Setting
Controller Setting
Joystick Calibration
●
26
26
27
28
31
English _7
overview
KEY FEATURES
SPC-2010 system controller enables you to control external devices such as PTZ camera, DVR using
RS-485/422 communications.
It provides a user-friendly interface with joystick.
• Long-distance remote control
• With RS-485/422 communications, the control distance is a maximum of 1km.
• Integrated system control
• With a single system controller, you can control all cameras (receiver unit), DVRs.
Compatibility List
• Camera
• DVR
SRD-XXXX series (Not supported by SRD-480D.)
8_ overview
WHAT’S INCLUDED
●
Unpack the product package and place the product on the floor or a flat surface.
Check if the following components are all included in the product package.
OVERVIEW
ESC
PWR
PWR Tx
1
2
3
4
5
6
7
8
9
CLR
0
ENT
MON
CAM
MENU
PRESET
GROUP
FUNC
SETUP
PTZ
MODE
AUDIO
REC
SEARCH
FREEZE
ALARM
Rx
PTZ/DVR
A/F
AUX
IRIS
FOCUS
W
ZOOM
T
Main Unit
User Manual CD (Optional)
User Manual
Quick Guide (Optional)
Warranty Card
Power Adaptor 1EA
TRx
Tx3
Tx2
Tx1
Terminal Block 1EA
English _9
overview
SYSTEM CONTROLLER AT A GLANCE
Front Side
b
c ESC
PWR
PWR Tx
Item
1
2
3
4
5
6
7
8
9
CLR
0
ENT
MON
CAM
MENU
PRESET
GROUP
FUNC
SETUP
PTZ
MODE
AUDIO
REC
SEARCH
FREEZE
ALARM
Rx
PTZ/DVR
A/F
AUX
IRIS
FOCUS
W
ZOOM
T
Description
DVR Play Bar
Play/Pause, Fast Forward/Fast Backward, Stop, Record
b ESC / PWR
Cancels a command or turns power on/off.
c LCD Display
Display the operation status and the setup menu of the system controller.
Controller Selection Bar
Used to select a camera, monitor or DVR.
Joystick Controller
You can manipulate the Pan/Tilt operation up or down in connection with the PTZ camera
or receiver unit.
Turn the joystick clockwise or counter clockwise to control zooming.
You can control the direction of the connected controller from the menu screen of the
controller.
Camera Operation Bar
Runs Preset, Group, Auto Focus and Aux output functions.
DVR Control Bar
Executes the selected DVR’s Audio, Search, screen mode selection, Freeze and Alarm
Control.
10_ overview
Item
Control Iris (-: CLOSE/+: OPEN)
FOCUS
Adjust the focus (-: NEAR/+: FAR)
ZOOM
Zoom In/Out (W: WIDE/T: TELE)
MENU
Enters PTZ and DVR menu.
FUNC
Press [FUNC] button and desired function button to run.
SETUP
Press a number button and press [SETUP] button to enter the settings
menu.
OVERVIEW
Others
IRIS
●
Camera Lens Bar
Description
Used in DVR mode for controlling the camera connected to the DVR.
Number (0-9)
Used to specify numeric characters for camera, monitor, DVR or Preset
settings.
ENT
Move to a desired item using the navigation buttons and select it.
CLR
Cancel the current operation.
Jog
Used to search for forward/reverse frame in DVR play mode.
Shuttle
Forward/Reverse/Play/FF/REW in DVR play mode.
Number (0-9), ENT, CLR
Buttons
Jog Shuttle
English _11
overview
Rear Side
Tx1 Tx2 Tx3 TRx
PROGRAM
DC IN 12V
b
Item
Description
Power
DC 12V input port. (
b RS-485/422
For RS-485/422 communication, connected to camera, DVR and other control devices.
M

[PROGRAM] is not for user’s accessing.
12_ overview
)
installation
PRECAUTIONS
INSTALLATION
• The product is designed for indoor use only.
• Keep it away from water or moisture.
• Do not put excessive force on it.
• Do not pull out the power cable forcibly.
• Do not dismantle it at your own.
• Use only the rated I/O range.
• Install the system controller on a flat table.
• The layout of the system controller and the wiring system are critical for a proper system operation.
• You must turn off the product before installing it.
• A severe impact or vibration may cause a system failure.
• Keep it away from a strong magnetic field or electric interference, or wireless devices such as radio or TV set.
• Keep the installation site clean and dust-free all the time while or after you have installed the system controller.
• Leaving an abnormal smoke or smell as it is may lead to a fire or electric shock.
If this is the case, turn off the system controller immediately and contact us for a technical assistance.
• Take an appropriate action if you find: damp floor, unearthed power extension cord, peeled-off power
cable, or absence of safety grounding.
- Operation Temperature : 0°C ~ 40°C
- Storage Temperature : -30°C ~ +60°C
- Operation Humidity : 20% ~ 85% RH
- Storage Humidity : ~ 90% RH
- Power Consumption : DC 12V, Max 1.1W (
J

●
Before you install the system controller, read through and comply with the following instructions.
)
Use a dry cloth to wipe it out. If badly dirty or stained, use a cloth soaked into neutral detergent to wipe it out.
Do not use volatile solvents such as alcohol, benzene or thinner that may damage the product surface.
English _13
connecting to an external device
SPC-2010 system controller can be used in connection with an external device such as camera
or DVR.
TO CONNECT A RS-485/422 DEVICE
With the system controller, you can control the PTZ camera or DVR that supports RS-485/422 communication
protocols.
1. Connect the rear Tx1 with RS-485 port of the PTZ camera or DVR.
2. According to the external device connected, select RS-485 (Half Duplex) or RS-422 (Full Duplex)
connection.
For RS-485/422 communications, pay special attention to the polarity (+/-).
Use the provided terminal block in the product package.
Check if the RS-485/422 device is compatible with SPC-2010.
Tx3
Tx2



TRx
M
Tx1
Tx1 Tx2 Tx3 TRx
PROGRAM
DC IN 12V
TRx
Tx3
Tx2
Tx1
Connecting RS-485/422 Signal Wires
• RS-485 Communications
• RS-422 Communications
Camera
Controller
Camera
Controller
RXD+
TRx+
RXD+
Tx1+
RXD–
TRx–
RXD–
Tx1–
TXD+
TRx+
TXD–
TRx–

You may use the Tx2 or Tx3 terminal instead of Tx1.
14_ connecting to an external device
Connecting the PTZ Camera

Depending on the camera, the polarity may differ.
For more information, refer to the user manual of the PTZ camera.
For the half duplex system
- Connect Rx (+) of RS-485 port of the PTZ camera with TRx (+) of SPC-2010.
- Connect Rx (–) of RS-485 port of the PTZ camera with TRx (–) of SPC-2010.
 If connecting a PTZ camera without using DVR device, you can connect to Tx1, Tx2 or Tx3 instead of TRx.
/0
"6%*0@*/ "6%*0@065
"9*$0.
*.0
7%$
59
"9*$0.
*.0
7%$
59
$0.
"9*$0.
*.0
7%$
39
(/%
"VY
TRx
"VY
/0
39
$POUSPMMFS
59
Tx3
(/%
$0.
1PXFS
"$_7
%%59%59%(/%"$0."/0
$POUSPMMFS
59
%%59%59%(/%"$0."/0
Tx2
Tx1 Tx2 Tx3 TRx
39
"MBSN0/
"MBSN0/
*/*/(/%*/*/(/%$.//$$.//$
7JEFP0VU
39
/$
/
$0.
/$
/
$0.
(/%
*/
*/
(/%
*/
*/
"MBSN
English _15
CONNECTING TO AN EXTERNAL DEVICE
M
●
By connecting RS-485 port on the rear of the PTZ camera with Tx of SPC-2010, you can control the
camera.
TRx
Tx3
Tx2
Tx1
Tx1
connecting to an external device
For the full duplex system
- Connect Rx (+) of RS-485 port of the PTZ camera with Tx1 (+) of SPC-2010.
- Connect Rx (–) of RS-485 port of the PTZ camera with Tx1 (–) of SPC-2010.
- Connect Tx (+) of RS-485 port of the PTZ camera with TRx (+) of SPC-2010.
- Connect Tx (–) of RS-485 port of the PTZ camera with TRx (–) of SPC-2010.
/0
"6%*0@*/ "6%*0@065
"9*$0.
*.0
7%$
59
"9*$0.
*.0
7%$
59
$0.
"9*$0.
*.0
7%$
39
(/%
"VY
TRx
"VY
Tx3
Tx2
Tx1
TRx
Tx3
Tx2
Tx1
16_ connecting to an external device
/0
39
$POUSPMMFS
59
(/%
$0.
1PXFS
"$_7
%%59%59%(/%"$0."/0
$POUSPMMFS
59
%%59%59%(/%"$0."/0
Tx1 Tx2 Tx3 TRx
39
"MBSN0/
"MBSN0/
*/*/(/%*/*/(/%$.//$$.//$
7JEFP0VU
39
/$
/
$0.
/$
/
$0.
(/%
*/
*/
(/%
*/
*/
"MBSN
Connecting SRD-16XX/8XX Series DVR
●
Connect between DVR and SPC-2010 using RS-485 port on the rear of the DVR.
- Connect Tx (+) of RS-485 port of the DVR with TRx (+) of SPC-2010.
- Connect Tx (–) of RS-485 port of the DVR with TRx (–) of SPC-2010.
CH 4
AUDIO OUT
AC 100-240~
IN
LOOP OUT
CH 2
CH 3
VIDEO IN
SPOT
AUDIO IN
CH 1
NETWORK
ALARM OUT
VGA
ALARM IN
SERIAL
CONSOLE
TRx
Tx3
Tx2
Tx1
USB
ALARM OUT
Tx1 Tx2 Tx3 TRx
TRx
Tx3
Tx2
Tx1
For the full duplex system
- Connect Tx (+) of RS-485 port of the DVR with TRx (+) of SPC-2010.
- Connect Tx (–) of RS-485 port of the DVR with TRx (–) of SPC-2010.
- Connect Rx (+) of RS-485 port of the DVR with Tx1 (+) of SPC-2010.
- Connect Rx (–) of RS-485 port of the DVR with Tx1 (–) of SPC-2010.
CH 4
AUDIO OUT
AC 100-240~
IN
LOOP OUT
CH 2
CH 3
VIDEO IN
SPOT
AUDIO IN
CH 1
NETWORK
ALARM OUT
VGA
ALARM IN
SERIAL
CONSOLE
TRx
Tx3
Tx2
USB
Tx1 Tx2 Tx3 TRx
ALARM OUT
TRx
English _17
CONNECTING TO AN EXTERNAL DEVICE
For the half duplex system
Tx3
Tx2
Tx1
Tx1
connecting to an external device
Connecting SRD-4XX DVR
Connect RS-485 port on the rear of SRD-4XX with SPC-2010.
For the half duplex system
- Connect Tx (+) of SRD-4XX with TRx (+) of SPC-2010.
- Connect Tx (–) of SRD-4XX with TRx (–) of SPC-2010.
TRx
Tx3
Tx2
Tx1
Tx1 Tx2 Tx3 TRx
Tx3
Tx2
Tx1

TRx
M
Not supported by SRD-480D.
18_ connecting to an external device
using the menu
GETTING STARTED
●
USING THE MENU
Power
1. When powered off, press [PWR] to turn on.
2. When powered on, press and hold [PWR] to turn off.
Initial Screen
• SAMSUNG-T: Shows the current channel’s protocol used for the camera
or DVR.
• 9.6K: Shows the current channel’s baud rate set for the camera or DVR.
SAMSUNG-T 9.6K
ID : 001
• ID: Shows the current channel’s number.
CONTROLLING THE PTZ CAMERA
To enter PTZ control mode
Press [PTZ/DVR] button to switch to PTZ control mode.
To select a camera
1. Use the number buttons to enter the number of the camera of your choice.
2. Press the [CAM] or [ENT] button to set the camera ID to the selected number.
 You can set between 1 ~ 255.
Note that the ID 0 allows SAMSUNG-T/E protocol only.
English _19
using the menu
PAN/TILT Control
You can use the controller joystick to adjust the pan/tilt angle of the camera.
The farther from the center of the joystick is, the faster the moving speed becomes.
20_ using the menu
IRIS
Press [IRIS – / +] on the controller to adjust the brightness of the camera video.
●
USING THE MENU
• IRIS – : camera Brighter
• IRIS + : camera Darker
FOCUS
Press [FOCUS – / +] on the controller to fit the camera focus.
• FOCUS – : Focus Closer
• FOCUS + : Focus Farther
ZOOM
Turn the joystick clockwise, or press [T] to control the zoom-in operation of the camera.
Turn the joystick counter clockwise, or press [W] to control the zoom-out operation of the camera.
• ZOOM W : Zoom Wide
• ZOOM T : Zoom Tele
< Zoom Wide Action >
< Zoom Tele Action >
English _21
using the menu
PRESET
Move the camera to a pre-determined point.
To set a preset
1. Using the joystick and controller buttons, move the camera to a desired location.
2. Enter a preset number.
3. Hold down the [PRESET] button for 2 seconds to save the preset location.
To execute the preset
1. Select a camera.
2. Enter a desired number(s) using the number buttons and press [PRESET].
3. The preset will be executed.
M

You can select preset numbers from 1 to 255 using the controller. The maximum preset location number varies
depending on the camera model. (For more information, please refer to your camera’s user manual.)

You can set up preset locations in the OSD menu of the camera.
GROUP
You can make a group of multiple presets before calling them in sequence.
To set a group
1. Enter the group number.
2. Press the [GROUP] button to activate the Group mode.
 To pause the Group mode, move the joystick.
M


In order to use Group modes, you must set up the modes in the camera’s OSD menu prior to actual operation.
Group function is available only for SAMSUNG-T/E protocol.
SAMSUNG-E protocol allows SCAN function.
22_ using the menu
A/F
●
1. Pressing the [A/F] button.
USING THE MENU
2. Execute One Shot AF function of the camera.
M

A/F function is available in SAMSUNG-T/E and Pelco-D/P protocols.
AUX
Controls the camera’s Aux output operation.
• AUX ON : Press the number of desired AUX channel and then briefly press [AUX] button to set Aux
output to ON.
• AUX OFF : Press the number of desired AUX channel and then press [AUX] button for about 2
seconds to set Aux output to OFF.
M

AUX function is available in SAMSUNG-T/E and Pelco-D/P protocols.
English _23
using the menu
CONTROLLING DVR
Depending on the model, the DVR may have different features available.
For details, refer to the applicable user manual.
M

An improper setting may cause a problem using the DVR.
To enter DVR control mode
Press [PTZ/DVR] button to switch to DVR control mode.
To select a DVR
1. Use the number buttons to enter a DVR number (0~255) and press [ENT].
2. Screen according to the selected DVR model appears.
M

PTZ control synchronizes to the settings configured in the selected DVR. When changed PTZ settings of the DVR,
select the DVR as instructed above to refresh synchronization to changed settings.
To select a DVR channel
1. Use the number buttons to enter the number for a desired DVR channel.
2. Press [CAM].
M

Hold [FUNC] button and select a channel’s number button to switch to the desired DVR channel. (Channel 1 ~ 9)
Controlling the DVR Spot Monitor
If using DVR that supports Spot Out, press the buttons below in a row to control Spot Out.
• To switch selected DVR’s Spot channel to a desired camera’s video:
SPOT monitor number + [MON] + Channel number + [CAM]
• To switch selected DVR’s Spot channel to a desired DVR’s split screen mode:
SPOT monitor number + [MON] + [MODE]
24_ using the menu
To control the DVR menu
●
1. To control the menus of the selected DVR, press [MENU] in the DVR control bar.
To control the PTZ device that is connected to DVR
Depending on used DVR model, you may not be able to directly control PTZ camera connected to the
DVR.
In such cases, press [PTZ/DVR] button in DVR control mode to switch to camera control mode, and
then you can control the camera.
To control the PTZ device in DVR mode
1. In DVR control mode, select a channel for PTZ control.
2. Press [
] button to display “
” on the right bottom side of the monitor.
3. Use joystick to control the PTZ camera connected to the DVR.
4. Press [
] button again. “
the previous mode.
” on the right bottom side of the monitor disappears and restores
DVR login
When accessing DVR menu, logging in may prompt for password depending on the DVR’s settings
configured.
• You can enter the DVR password as in the way of channel selection.
Ex) If the DVR’s password is “4321”, press buttons below in a row to login to the DVR.
[4] + [CAM] + [3] + [CAM] + [2] + [CAM] + [1] + [CAM]
M

DVR password can be entered using the [FUNC] button too.
Refer to “To select a DVR channel”. (Page 24)
English _25
USING THE MENU
2. Use joystick and [ENT] to traverse DVR menu.
menu setting
PTZ SETTING
From the PTZ setup screen, you can specify the protocol and baud rate.
1. Press [1] on the number pad.
Hold down the [SETUP] button to enter the PTZ SETUP mode.
2. Enter the 4-digit password.
 Default Password : 4321
J

The default password can be exposed to a hacking thread so it is recommended to
change the password after installing the product.
Note that the security and other related issues caused by the unchanged password
shall be responsible for the user.
3. To change a channel address, select a channel by moving the joystick to
the right or left. Or you can enter the channel number and then press the
[ENT] button.
4. Change the <MODEL>, <BAUDRATE> and <PARITY> settings of the
select channel.
M



To move between the options, move the joystick up or down.
To change the value of the settings, move the joystick to the right or left.
For the default settings values, please refer to the picture on the right.
BAUDRATE : 9.6K, PARITY : NONE
5. Select the <SAVE> menu to save the changes.
You can continue changing the settings by selecting different channels.
To exit to the initial screen, select the <EXIT> menu or press the [ESC]
button.
J

After changing the settings of a channel, you must select the <SAVE> menu.
If you move to a different channel without using the <SAVE> menu, the changes
will not be saved.

Under Controller Serial Setup, Data Bit is fixed to 8 and Stop Bit to 1.
Serial values of the controller and camera must match each other.

Note that the ID 0 allows SAMSUNG-T/E protocol only.
26_ menu setting
[ PTZ SETUP 1 ]
PASSWORD [ **** ]

[ PTZ SETUP 1]
1. ADDRESS : 001

[ PTZ SETUP 1]
2. MODEL : SAMSUNG-T

[ PTZ SETUP 1]
3. BAUDRATE : 9.6K

[ PTZ SETUP 1]
4. PARITY : NONE

[ PTZ SETUP 1 ]
5. SAVE

[ PTZ SETUP 1 ]
6. EXIT
DVR SETTING
2. Enter the 4-digit password.
 Default Password : 4321
J

The default password can be exposed to a hacking thread so it is recommended to
change the password after installing the product.
Note that the security and other related issues caused by the unchanged password
shall be responsible for the user.
3. To change a channel address, select a channel by moving the joystick to
the right or left. Or you can enter the channel number and then press the
[ENT] button.
4. Change the <BAUDRATE> and <PARITY> settings of the select
channel.
M



To move between the options, move the joystick up or down.
To change the value of the settings, move the joystick to the right or left.
For the default settings values, please refer to the picture on the right.
Protocol : Samsung Techwin SAMSUNG-T
BAUDRATE : 9.6K, PARITY : NONE
5. Select the <SAVE> menu to save the changes.
You can continue changing the settings by selecting different channels.
To exit to the initial screen, select the <EXIT> menu or press the [ESC]
button.
J

After changing the settings of a channel, you must select the <SAVE> menu.
If you move to a different channel without using the <SAVE> menu, the changes
will not be saved.

Under Controller Serial Setup, Data Bit is fixed to 8 and Stop Bit to 1.
Serial values of the controller and camera must match each other.
[ DVR SETUP 1 ]
PASSWORD [ **** ]

[ DVR SETUP 1]
1. ADDRESS : 001

[ DVR SETUP 1]
2. BAUDRATE : 9.6K

[ DVR SETUP 1]
3. PARITY : NONE

[ DVR SETUP 1 ]
4. SAVE

[ DVR SETUP 1 ]
5. EXIT
English _27
MENU SETTING
1. Press [2] on the number pad.
Hold down the [SETUP] button to enter the DVR SETUP mode.
●
From the DVR setup screen, you can specify the DVR type and baud rate.
menu setting
CONTROLLER SETTING
1. Press [3] on the number pad.
2. Hold down the [SETUP] button to enter the controller’s MAIN SETUP
mode.
[ MAIN SETUP ]
PASSWORD [ **** ]
3. Enter the 4-digit password.
 Default Password : 4321
J

The default password can be exposed to a hacking thread so it is recommended to change the password after
installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
4. After changing the settings, select <YES> in the <SAVE/EXIT> menu
to save the changes and move back to the initial screen. To cancel
changes and move back to the initial screen, select <NO> in the
<SAVE/EXIT> menu or press the [ESC] button.
M



[ MAIN SETUP ]
10. SAVE/EXIT
To move between the options, move the joystick up or down.
To change the value of the settings, move the joystick to the right or left.
For the default settings values, please refer to the picture on the right.
Firmware Version
Displays the current version of the controller firmware.
[ MAIN SETUP ]
1. v1.00_XXXXXX
Serial Data Transfer Standard
You can select serial communication mode from <RS485> and <RS422>.
28_ menu setting
[ MAIN SETUP ]
2. COMM : RS485
LCD Backlight
• ON : Keeps the backlight on at all times.
[ MAIN SETUP ]
3. BACKLIGHT : AUTO
• OFF : Keeps the backlight off at all times.
Sleep
If the controller is not used for specified time, it switches to SLEEP mode.
Operating joystick or button of the controller exits SLEEP mode.
[ MAIN SETUP ]
4. SLEEP : OFF
Buzzer
You can set the controller to beep on button pressings.
• ON: Each pressing of a button beeps.
• OFF: Pressing a button produces no sound.
[ MAIN SETUP ]
5. BUZZER : ON
Terminate
To prevent the attenuation of communication signals between the camera
and controller, the controller’s termination option must be <ON> if it is
located farthest from the camera and controller communication loop. If the
controller is in the middle of the camera and controller communication loop,
turn the termination option <OFF>.
[ MAIN SETUP ]
6. TERMINATE : ON
English _29
MENU SETTING
• AUTO : Turns the backlight off automatically if no command has been
entered in the last 30 seconds.
●
You can set the controller’s LCD backlight setting to OFF, ON or AUTO.
menu setting
Joystick’s Serial Command Transfer Cycle
Select a PTZ serial command transfer cycle for using the joystick.
Shortening the transfer cycle increases the response speed of the camera.

J

[ MAIN SETUP ]
7. JOY SPD : 100MS
Shortening the joystick’s serial command transfer cycle may cause certain camera models to not process commands
properly.
To prevent and resolve such malfunctions, extend the transfer cycle.
Password
You can set the controller password.
Enter a new password.
[ MAIN SETUP ]
8. PASSWORD : ****
M

The default password is “4321”.
J

The default password can be exposed to a hacking thread so it is recommended to change the password after
installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
Factory Set
Resets the controller’s current settings to the factory release default values
and optimizes the joystick calibration.
30_ menu setting
[ MAIN SETUP ]
9. FACTORY SET
JOYSTICK CALIBRATION
●
1. Press [4] on the number pad.
3. At each option, move the joystick as far as you can, and then press the [ENT] button to calibrate.
[ JOYSTICK CALI. ]
1. PTZ OFFSET **
[ JOYSTICK CALI. ]
2. PAN LEFT ***


Move to the far left
side
Joystick in the Center
[ JOYSTICK CALI. ]
4. TILT UP ***

[ JOYSTICK CALI. ]
7. ZOOM TELE ***
[ JOYSTICK CALI. ]
6. ZOOM WIDE ***

Move to the far
lower side

Move to the far
right side
[ JOYSTICK CALI. ]
5. TILT DOWN ***
Move to the far
upper side
Rotate to the Tele
direction as far as
possible
[ JOYSTICK CALI. ]
3. PAN RIGHT ***
Rotate to the Wide
direction as far as
possible

[ J O Y S T I C K S AV E ]
<NO>
YES

Select <YES> to save the changes and move back to the initial screen.
Select <NO> or press the [ESC] button to cancel changes and move back to the
initial screen.
English _31
MENU SETTING
2. Hold down the [SETUP] button to enter the Joystick Calibration mode.
appendix
SPECIFICATIONS
Item
Description
Communication
Communication System
RS-485 / 422
Baud Rate
2,400 ~ 57,600 bps
Compatibility
PTZ / DVR / RECEIVER
PTZ
SAMSUNG-T/E, PELCO-D/P, Panasonic, Vicon, AD, Honeywell, BOSCH, ELMO, GE
Zoom
SCZ
DVR
SRD (Not supported by SRD-480D.)
Receiver
Samsung-T
Protocol
Operational
LCD Display
16 x 2 character LCD
Joystick
3 axial Twist Zoom
Jog Shuttle
Control DVD playback
OSD
English
32_ appendix
Environmental
Operation Humidity
20%~85% RH
APPENDIX
0°C ~ 40°C
●
Operation Temperature
Electrical
Input Voltage /Current
12 VDC
Power consumption
1.1W
Mechanical
Dimensions (WXHXD)
W334.1 X H171.1 X D105.2 mm (13.15 X 6.74 X 4.14 inch)
Weight
800g
English _33
appendix
PRODUCT OVERVIEW
171.1 (6.74")
unit : mm (inches)
334.1 (13.15")
105.2 (4.14")
76.6 (3.02")
34_ appendix
28.6
(1.13")
TROUBLESHOOTING
●
Countermeasures
If the power is not turned on
• Check the connection between the main unit and adaptor.
If the problem persists even if there’s no problem with connection, consult your
dealer for servicing.
If the joystick does not move, or the
controller buttons are not pressed
• There may be a problem with the controller board. Please contact your nearest
dealer for further assistance.
If the controller cannot control the
camera
If forgot password
• Please check the network cable between the controller and camera.
• Check if the controller’s PTZ/DVR mode and ID are properly selected.
• Please check the protocol and serial settings of the controller and camera.
• Consult your dealer.
English _35
APPENDIX
Symptom
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at
his own expense.
Samsung Techwin cares for the environment at all product manufacturing stages, and is taking
measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products,
and indicates that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste
at the end of their working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take these items for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product and its electronic accessories should not be mixed with other commercial
wastes for disposal.
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
PT01-001332A