Carrier AQUAFORCE 30XA080-500 Operating instructions

AQUAFORCE®
30XA080-500
Air-Cooled Liquid Chillers
Controls, Start-Up, Operation, Service
and Troubleshooting
CONTENTS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . .2,3
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Conventions Used in This Manual . . . . . . . . . . . . . . . . 3
Display Module Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
• TOUCH PILOT™ DISPLAY
• NAVIGATOR™ DISPLAY MODULE
CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Main Base Board (MBB) . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Compressor Protection Module (CPM) . . . . . . . . . . . 9
Electronic Expansion Valve (EXV) Board . . . . . . . . . 9
Fan Boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Enable-Off-Remote Contact Switch (SW1) . . . . . . . 17
Emergency On/Off Switch (SW2) . . . . . . . . . . . . . . . . 17
Energy Management Module (EMM) . . . . . . . . . . . . . 17
Hot Gas Bypass/Pump Board . . . . . . . . . . . . . . . . . . . 17
Local Equipment Network . . . . . . . . . . . . . . . . . . . . . . . 19
Board Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Touch Pilot Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Control Module Communication. . . . . . . . . . . . . . . . . 19
• RED LED
• GREEN LED
• YELLOW LED
Carrier Comfort Network® (CCN) Interface. . . . . . . 20
Remote Alarm and Alert Relays . . . . . . . . . . . . . . . . . 20
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-59
Touch Pilot Operation Configuration Tables . . . . . 21
Machine Control Methods . . . . . . . . . . . . . . . . . . . . . . . 22
Machine On/Off Control . . . . . . . . . . . . . . . . . . . . . . . . . 22
• TOUCH PILOT MACHINE CONTROL
• NAVIGATOR DISPLAY MACHINE CONTROL
Fluid Set Point Control Location . . . . . . . . . . . . . . . . 27
Cooling Set Point Selection . . . . . . . . . . . . . . . . . . . . . 27
• SET POINT OCCUPANCY
Chilled Water Fluid Type Selection . . . . . . . . . . . . . . 28
• FRESH WATER
• BRINE OR GLYCOL OPERATION
Cooler Pump Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
• NO PUMP CONTROL
• SINGLE PUMP CONTROL
• DUAL PUMP AND MANUAL CONTROL
Machine Start Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Circuit/Compressor Staging and Loading . . . . . . . 31
• CIRCUIT/COMPRESSOR STAGING
• CIRCUIT/COMPRESSOR LOADING
Minimum Load Control . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Dual Chiller Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
• DUAL CHILLER CONTROL FOR PARALLEL
APPLICATIONS
• DUAL CHILLER PUMP CONTROL FOR PARALLEL
CHILLER APPLICATIONS
Page
• DUAL CHILLER CONTROL FOR SERIES
APPLICATIONS
• DUAL CHILLER PUMP CONTROL FOR SERIES
CHILLER APPLICATIONS
Night Time/Low Noise Applications . . . . . . . . . . . . . 37
Ramp Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Temperature Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
• RETURN WATER RESET
• OUTSIDE AIR TEMPERATURE RESET
• SPACE TEMPERATURE RESET
• 4-20 mA TEMPERATURE RESET
Demand Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
• SWITCH CONTROLLED DEMAND LIMIT
• EXTERNALLY POWERED CAPACITY BASED
DEMAND LIMIT
• EXTERNALLY POWERED CURRENT BASED
DEMAND LIMIT
• CCN LOADSHED CONTROLLED DEMAND LIMIT
Ice Storage Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Broadcast Configuration . . . . . . . . . . . . . . . . . . . . . . . . 46
• ACTIVATE
• OAT BROADCAST
• BROADCAST ACKNOWLEDGER
Alarm Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
• ALARM ROUTING CONTROL
• ALARM EQUIPMENT PRIORITY
• COMMUNICATION FAILURE RETRY TIME
• RE-ALARM TIME
• ALARM SYSTEM NAME
Daylight Saving Time Configuration. . . . . . . . . . . . . 47
Capacity Control Overrides . . . . . . . . . . . . . . . . . . . . . 47
Head Pressure Control . . . . . . . . . . . . . . . . . . . . . . . . . . 50
• LOW AMBIENT TEMPERATURE HEAD PRESSURE
CONTROL OPTION
• LOW AMBIENT TEMPERATURE HEAD PRESSURE
CONTROL OPERATING INSTRUCTIONS
PRE-START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
System Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-67
Actual Start-Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Operating Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
• TEMPERATURES
• VOLTAGE
• MINIMUM FLUID LOOP VOLUME
• FLOW RATE REQUIREMENTS
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67-74
Sequence of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . 67
• ACTUATED BALL VALVE (ABV), FLOODED
COOLER ONLY
Dual Chiller Sequence of Operation . . . . . . . . . . . . . 68
• PUMP OPERATION
Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
• THERMISTORS
• TRANSDUCERS
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53300091-01
Printed in U.S.A.
Form 30XA-4T
Pg 1
612
10-11
Replaces: 30XA-3T
Page
CONTENTS (cont)
APPENDIX F — MAINTENANCE SUMMARY
AND LOG SHEETS. . . . . . . . . . . . . . . . . . . . . . . . . . 165-167
APPENDIX G — BACNET COMMUNICATONS
OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168-178
Page
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74-87
Economizer Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Electronic Expansion Valve (EXV) . . . . . . . . . . . . . . . 74
• FLOODED COOLER MAIN EXV CONTROL
• DX COOLER MAIN EXV CONTROL
• ECONOMIZER EXV CONTROL
• EXV TROUBLESHOOTING PROCEDURE
Compressor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 77
• COMPRESSOR OIL SYSTEM
Flooded Cooler Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
• FLOODED COOLER SUCTION SERVICE VALVE
• FLOODED COOLER FREEZE PROTECTION
• FLOODED COOLER LOW FLUID TEMPERATURE
• FLOODED COOLER LOSS OF FLUID FLOW
PROTECTION
• FLOODED COOLER TUBE PLUGGING
• FLOODED COOLER RETUBING
• FLOODED COOLER TIGHTENING COOLER HEAD
BOLTS
• FLOODED COOLER INSPECTING/CLEANING
HEAT EXHANGERS
• FLOODED COOLER WATER TREATMENT
DX Cooler Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
• DX COOLER SUCTION SERVICE VALVE
• DX COOLER FREEZE PROTECTION
• DX COOLER LIQUID FLUID TEMPERATURE
• DX COOLER LOSS OF FLUID FLOW PROTECTION
• DX COOLER TUBE PLUGGING
• DX COOLER RETUBING
• DX COOLER TIGHTENING COOLER HEAD BOLTS
• DX COOLER CHILLED WATER FLOW SWITCH
DX Cooler and Flooded Cooler Units . . . . . . . . . . . . 84
• PREPARATION FOR WINTER SHUTDOWN
Microchannel Heat Exchanger (MCHX) Condenser
Coil Maintenance and Cleaning
Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
RTPF Condenser Coil Maintenance and Cleaning
Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
• REMOVE SURFACE LOADED FIBERS
• PERIODIC CLEAN WATER RINSE
• ROUTINE CLEANING OF RTPF COIL SURFACES
Condenser Fans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Refrigerant Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
• LEAK TESTING
• REFRIGERANT CHARGE
Safety Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
• COMPRESSOR PROTECTION
• OIL SEPARATOR HEATERS
• COOLER PROTECTION
Relief Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
• PRESSURE RELIEF VALVES
MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87,88
Recommended Maintenance Schedule . . . . . . . . . . 87
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . 88-109
Alarms and Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
• DIAGNOSTIC ALARM CODES AND POSSIBLE
CAUSES
Service Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
APPENDIX A — TOUCH PILOT™
DISPLAY TABLES . . . . . . . . . . . . . . . . . . . . . . . . . 110-127
APPENDIX B — NAVIGATOR™
DISPLAY TABLES. . . . . . . . . . . . . . . . . . . . . . . . . . 128-141
APPENDIX C — CCN TABLES . . . . . . . . . . . . . . 142-156
APPENDIX D — 30XA080-500 CPM
DIP SWITCH ADDRESSES. . . . . . . . . . . . . . . . 157-160
APPENDIX E — PIPING AND
INSTRUMENTATION . . . . . . . . . . . . . . . . . . . . . . 161-164
612
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
START-UP CHECKLIST
FOR 30XA LIQUID CHILLERS . . . . . . . . CL-1 to CL-8
SAFETY CONSIDERATIONS
Installing, starting up, and servicing this equipment can be
hazardous due to system pressures, electrical components, and
equipment location (roof, elevated structures, etc.). Only
trained, qualified installers and service technicians should
install, start up, and service this equipment. When working on
this equipment, observe precautions in the literature, on tags,
stickers, and labels attached to the equipment, and any other
safety precautions that apply. Follow all safety codes. Wear
safety glasses and work gloves. Use care in handling, rigging,
and setting this equipment, and in handling all electrical
components.
WARNING
Electrical shock can cause personal injury and death. Shut
off all power to this equipment during installation and service. There may be more than one disconnect switch. Tag
all disconnect locations to alert others not to restore power
until work is completed.
WARNING
DO NOT VENT refrigerant relief valves within a building.
Outlet from relief valves must be vented in accordance
with the latest edition of ANSI/ASHRAE (American
National Standards Institute/American Society of Heating,
Refrigerating and Air Conditioning Engineers) 15 (Safety
Code for Mechanical Refrigeration). The accumulation of
refrigerant in an enclosed space can displace oxygen and
cause asphyxiation. Provide adequate ventilation in
enclosed or low overhead areas. Inhalation of high concentrations of vapor is harmful and may cause heart irregularities, unconsciousness or death. Misuse can be fatal. Vapor
is heavier than air and reduces the amount of oxygen available for breathing. Product causes eye and skin irritation.
Decomposition products are hazardous.

WARNING
DO NOT USE TORCH to remove any component. System
contains oil and refrigerant under pressure.
To remove a component, wear protective gloves and goggles and proceed as follows:
a. Shut off electrical power to unit.
b. Recover refrigerant to relieve all pressure from system using both high-pressure and low pressure ports.
c. Traces of vapor should be displaced with nitrogen
and the work area should be well ventilated. Refrigerant in contact with an open flame produces toxic
gases.
d. Cut component connection tubing with tubing cutter
and remove component from unit. Use a pan to catch
any oil that may come out of the lines and as a gage
for how much oil to add to the system.
e. Carefully unsweat remaining tubing stubs when necessary. Oil can ignite when exposed to torch flame.
Failure to follow these procedures may result in personal
injury or death.
2
configuration. The user would scroll through the modes and
sub-modes using the
and
keys on the Navigator display.
For the Touch Pilot display, the user would simply touch the menu
item on the screen. The arrow symbol in the path name represents
pressing ENTER to move into the next level of the menu structure for the Navigator module, or touching the menu item on the
screen for the Touch Pilot display.
CAUTION
This unit uses a microprocessor-based electronic control
system. Do not use jumpers or other tools to short out components, or to bypass or otherwise depart from recommended procedures. Any short-to-ground of the control
board or accompanying wiring may destroy the electronic
modules or electrical components.
When a value is included as part of the point name, it will be
shown after the point name after an equals sign. If the value
represents a configuration setting, an explanation will be
shown in parentheses after the value. The Touch Pilot name
will be shown first with the Navigator name following. As an
example,
(Staged Loading Sequence = 1, LLCS = Circuit A leads).
Press the ESCAPE and ENTER keys simultaneously on
the Navigator module to display an expanded text description of
the point name or value. The expanded description is shown in the
Navigator display tables (Appendix B) but will not be shown with
the path names in text. The Touch Pilot display will show an
expanded description of the point name. To view the expanded
point name for the Touch Pilot display go to Appendix A.
CAUTION
To prevent potential damage to heat exchanger tubes,
always run fluid through heat exchanger when adding or
removing refrigerant charge. Use appropriate antifreeze
solutions in cooler fluid loop to prevent the freezing of heat
exchanger or interconnecting piping when the equipment is
exposed to temperatures below 32 F (0° C). Proof of flow
switch is factory installed on all models. Do NOT remove
power from this chiller during winter shut down periods
without taking precaution to remove all water from heat
exchanger. Failure to properly protect the system from
freezing may constitute abuse and may void warranty.
The Touch Pilot display configures the unit via the CCN
(Carrier Comfort Network®) Tables, which are located in Appendix C of this manual.
CAUTION
Compressors require specific rotation. Test condenser
fan(s) first to ensure proper phasing. Swap any two incoming power leads to correct condenser fan rotation before
starting compressors. Operating the unit without testing the
condenser fan(s) for proper phasing could result in equipment damage.

Display Module Usage
TOUCH PILOT DISPLAY — The Touch Pilot display is the
standard user interface for the AquaForce 30XA chillers with
the ComfortLink control system. The display includes a large
LCD (liquid crystal display) touch screen for display and user
configuration, a Start/Stop button, and an Alarm Indicator LED
(light-emitting diode). See Fig. 1.
CAUTION
LCD TOUCH SCREEN
DO NOT re-use compressor oil or any oil that has been
exposed to the atmosphere. Dispose of oil per local codes
and regulations. DO NOT leave refrigerant system open to
air any longer than the actual time required to service the
equipment. Seal circuits being serviced and charge with
dry nitrogen to prevent oil contamination when timely
repairs cannot be completed. Failure to follow these procedures may result in damage to equipment.
ALARM
INDICATOR
LIGHT
GENERAL
This publication contains Controls, Operation, Start-Up,
Service and Troubleshooting information for the 30XA080500 air-cooled liquid chillers with electronic controls. The
30XA chillers are equipped with ComfortLink™ controls and
electronic expansion valves. The AquaForce® 30XA chillers
offer two different user interface devices, the Touch Pilot™
display and the Navigator ™ display.
START-STOP
BUTTON
Figure-1
Fig. 1 — Touch Pilot™ Display
The Touch Pilot display can be used to access various
Carrier Comfort Network® devices. For operation under these
circumstances, contact your Carrier representative.
Operation of the Touch Pilot display is driven from the
displays on the touch screen. The Touch Pilot display uses the
following screen “buttons” to allow the user to operate the display and navigate within and between screens.
“BACK” Returns to the next higher screen in the
hierarchy.
“HOME” Displays the Default Group Display screen
for Touch Pilot display. The Default Screen is a userconfigured display of up to 9 points on each of 8 screens. This
allows for quick access to various, frequently viewed points,
without navigating through the Main Menu structure. This button is available at all menu levels and returns the user to the
first Default Group Display screen.
Conventions Used in This Manual — The following conventions for discussing configuration points for the
Navigator module and Touch Pilot display will be used in this
manual.
Point names for the Touch Pilot display will be shown in
bold. See Appendix A for a complete list of point names. Item
names for the Navigator module will be shown in bold italics.
See Appendix B for the complete path name preceeding the
item name. The point and item names in Appendices A and B
will be listed in alphabetical order and the path name for each
will be written with the mode name first, then any sub-modes,
each separated by an arrow symbol (.
This path name will show the user how to navigate through the
Navigator module or the Touch Pilot display to reach the desired
3
612
with up to 9 points on 8 separate screens. For more information
on adding or removing points from the Group Display screen,
see the Group Display Screens section on page 6.
Touch any of the screen point buttons and Point Data Dialog
box will be displayed with expanded information. In the example shown below, the CTRL_PNT button in the bottom left
corner was selected. See Fig. 2 and 3.
To exit the box, press
.
Main Menu Display — The default screen for the Touch Pilot
controller is the Group Display screen. To access the Main
Menu, press the
button. The screen shown in Fig. 4 will be
displayed. Selecting a button will display the screens associated with that category. The user can also access the login screen
from the Main Menu if needed.
“MAIN MENU” Displays the Main Menu screen.
This allows access for viewing and configuration,
where possible, of all points supported by the controller. This
includes points such as set point and operational configuration.
This button is available at all menu levels and returns the user
to the Main Menu screen.
“PREVIOUS” In a group of sequential screens of the
same type, pressing this button moves the user to the
next earlier screen in the group.
“NEXT” In a group of sequential screens of the same
type, pressing this button advances the user to the next
screen in the group.
“OK” Agrees with, or says “yes” to a prompt and performs the appropriate processing.
“NO” Rejects, or says “no” to a prompt and performs
the appropriate processing.
“CANCEL” Terminates an ongoing action and returns
to the current screen without any other processing.
“CLEAR DATA” Clears the data value in a data entry
dialog box. This button is used to clear incorrect data.
“RESET DATA” Zeros the data value in a data entry
dialog box.
“ADD” Adds the active point to a Group Display
screen.
“REMOVE” Deletes a point from a Group Display
screen.
“INCREASE” Modifies the value of a field within its
defined limits or “SCROLL UP” and shifts the screen
view up by one item.
“DECREASE” Modifies the value of a field within its
defined limits or “SCROLL DOWN” and shifts the
screen view down by one item.
“PAGE DOWN” If the current table or list has more
data than will fit on the screen, pressing this button
will replace the items currently on the screen with the next
group of items.
“PAGE UP” If the current table or list has more data
than will fit on the screen, pressing this button will
replace the items currently on the screen with the previous
group of items.
“FORCE” Begins the process of forcing or overriding
the value of a point.
“AUTO” Begins the process of removing a force from
a point.
“MODIFY” Begins the process of modifying a configuration value.
“ALARM INDICATOR LIGHT” An LED alarm
indicator light is activated when a new alarm condition occurs. The alarm indicator light, located on the
right side of the display, remains activated until it is manually
reset using the Reset button on the Main menu.
“START/STOP BUTTON” The Touch Pilot™ display includes an equipment Start/Stop Button that
enables the user to start or stop the chiller from the
display. See Enable-Off-Remote Contact Switch (SW1) on
page 17 for additional information.
Several items are password protected. When required, a
Password dialog box will be displayed for field input of the
password. The default password is 3333. The password can be
changed if desired.
Power-Up Display — When the Touch Pilot display is powered up, it displays an initialization progress bar and attaches
(initiates communication) to the Main Base Board. The Touch
Pilot display then shows that controller’s default Group Display screen. See Fig. 2. This is a user-configured display screen
Touch Pilot Menu Structure — The user can navigate through
the Touch Pilot display screens by selecting the buttons that appear on the screen. When a button is selected, either a submenu or a list of point names and values will be shown. Submenus will display a list of associated point names. See Fig. 5
for the Touch Pilot menu structure.
If the list of point names and values are shown, the top line
of the display is the table name. The line and total line counter
is displayed in the upper right corner of the display. Selecting
an item will cause a Point Data dialog box to appear.
Setup Menu Screen — The Setup Menu screen, shown in
Fig. 6, is accessed by pressing the Setup button from the Main
Menu. This configuration allows the user to configure the basic
operation and look of the display. Table 1 summarizes the Setup Menu functions.
4
Fig. 2 — Group Display Screen
a30-4470
Fig. 3 — Point Data Dialog Box
a30-4471
a30-4474
Fig. 4 — Main Menu Display
a30-4472
Fig. 6 — Setup Menu Display
User interface
Group display x 8
Status
Schedule
Service
Maint
Config
Alarms
GENUNIT
OCC1PO1S
FACTORY
LOADFACT
Ctrl-ID
ALARHIST
Regional
CIRCA_AN
OCC2PO2S
FACTORY2
FANCTRL
DISPCONF
ALARHIS2
Language
CIRCA_D
SERVICE1
M_MSTSLV
USER
ALAM_CUR
Contrast
CIRCB_AN
CP_UNABL
DEFROSTM
MST_SLV
Backlight
CIRCB_D
UPDTHOUR
LAST_POR
CFG_TAB1
Calibrate
CIRCC_D
UPDHRFAN
PR_LIMIT
…
Password
CIRCC_AN
MAINTCFG
BOARD_PN
…
Display
STATEGEN
SERMAINT
CFG_TAB8
CCN
RECLAIM
EXV_CTRL
BRODEFS
MODES
CUR_PHAS
OCCDEFCS
STRTHOUR
OCCDEFCFM
HOLIDAY
FANHOURS
Setpoint
Main menu
Reset
Time
Attach
Setup
Login
ALARMDEF
FREECOOL
a30-4473
QCK_TST1
QCK_TST2
SERV_TST
Fig. 5 — Touch Pilot™ Display Menu Structure
5
Table 1 — Setup Menu
SETUP MENU BUTTON
REGIONAL
LANGUAGE
CONTRAST
BACKLIGHT
CALIBRATE
FUNCTION
This button specifies the time and date format and the base unit of measure. Time display can be configured as 12hour AM/PM setting or as a 24-hour setting. The date can be formatted in one of 3 settings, MM-DD-YYYY (MonthDay-Year), DD-MM-YYYY (Day-Month-Year), or YYYY-MM-DD (Year-Month-Day). Units of measure can be either US
(English) or Metric (SI).
This button selects the active language and font of the display. Available languages are English and Spanish (Espanol).
If a preferred language is not available, additional software for the Main Base Board (MBB) and the Touch Pilot™ display are required. Contact your Carrier representative for instructions and software.
This button adjusts the LCD contrast. Press and hold the [MOON] button to increase/darken the contrast or the [STAR]
button to decrease/lighten the current contrast.
NOTE: Touching the screen anywhere for 5 seconds while powering-up will prompt the user to restore contrast and
calibration settings to factory defaults.
This button specifies whether backlighting should be kept on at all times or turned off during inactive periods.
This button is used to adjust the LCD touch screen calibration. Touch the screen in the circular targets located first in
the upper left and then in the lower right corner of the screen to adjust.
This button is used to configure the limited and full logged-in access system passwords. In order to change passwords,
the user must be logged in with full access to view and change the passwords. All passwords must consist of 4-digits,
which can be entered using the numeric keypad. Access levels and associated privileges are as follows:
Limited Logged-in Access - Provides the user with read/write access to all available tables (except service configuration tables, where the user will not be permitted to modify point data, and Group Display tables, where the user will not
be permitted to add points.) This access level also provides read/write access to all Touch Pilot display setup properties
except Display, CCN, and Password.
PASSWORDS
Full Logged-in Access - Provides user with read/write access to all available tables for the attached device and all
Touch Pilot display properties.
If the user does not log in, read-only access to all tables is allowed. The user will be prompted to log in when attempting
to access password-required functions.
This button is used to view the description data and part number from the Ctlr-ID Table and to specify the Operating
Mode. The Operating mode can be configured for Equipment mode or Network mode. For Touch Pilot displays that are
standard with the unit, Operating mode should not be changed from Equipment mode. Equipment mode provides
access only to the chiller’s MBB via the Local Equipment Network (LEN) Bus. For remote access, a remote Touch Pilot
display can be set to Network mode. Network mode provides access to all devices on the CCN (Carrier Comfort Network®) bus.
DISPLAY
NOTE: When changing the operating mode, a power cycle is required in order for the new operating mode to take
effect. The user should view and correct the following CCN data: address and baud rate, alarm acknowledger, and
broadcast acknowledger designation.
This button is used to configure the bus and element numbers and the baud rate of the control on the network.
CCN
Group Display Screens — The Touch Pilot™ display supports up to eight Group Display screens. Group Display
screens show status information along the top of the screens
and nine buttons that display nine point names and point values
that are chosen by the user. All Group Display screen points are
user configurable. The bottom line of the screen contains navigation buttons that can be used to move between the Group
Display screens.
Pressing a point button will show that point’s Point Data
dialog box. See Fig. 2 and 3. This box contains buttons that
remove the point from the group display and apply or remove a
force (point override). When touching any button in the display
screen, the button will be outlined to acknowledge input. There
may be a delay in response to input, but if the button is outlined, do NOT press any other button until the previous input
has been processed.
If there is a communication failure with the MBB (Main
Base Board), all point buttons will be displayed in inverse video and the message Communication Failure will be displayed
in the top left line of the screen.
Default Group Designation — The default group is the first of
the 8 Group Display screens. This is the default screen of the
display. Information on this screen as well as the other 7
screens can be user-modified to meet the needs of the site.
To Add a Point To a Group Display — From the Main Menu,
press the desired menu button (Status, Setpoint, Service,
Maint, or Config) and, if necessary, the sub-menu button to
access the point to be added. Press the point button to show the
source point’s Point Data dialog box. See Fig. 3. From the
Point Data dialog box, press the ADD button. The display will
show the last Group Display accessed. Use the navigation buttons to access the destination Group Display. Press an existing
Setting the Time and Date — The ComfortLink™ control has
a time and date function. This can be useful for diagnostics to
determine when alarms occur. The control is factory configured for the proper date and is set for the Eastern Time Zone.
The date and time zone must be checked and corrected if necessary, to allow the machine to function on an internal time
schedule and to display a proper time and date stamp for
alarms. The time and date is displayed on the Group Display
Screen.
To change the Time and Date, press the
Main Menu
button. Select
Time. On the display, a day and date box
with a time box will be shown. To change the day and date,
press the day and date box. A calendar will be displayed. If the
correct month is displayed, touch the correct date. If the wrong
month is displayed, use the
or
to change to the correct
month and select the correct date. The date will highlighted.
Press
to accept the change. The previous screen will be
displayed with the corrected day and date shown. To correct
the time, use the
the
or
or
on the left to change the hour. Use
on the left to change the minutes. Continuously
touching the
or
will sequence the numbers. The time is
shown in a 24-hour format. To accept the changes, press the
or
buttons. A “Save” dialog box is displayed with the
words, “Do you wish to save changes?” Press
to accept
the changes.
6
display will be shown. If communication is not established, the
Navigator module will display:
Communication
Failure
If the Navigator module is connected to a Main Base Board
without software loaded, the display will remain at the
powered-up initialization display.
Setting the Time and Date — The ComfortLink control has a
time and date function. This can be useful for diagnostics to determine when alarms occur. The control is factory configured
for the proper date and for use in the Eastern Time Zone. The
control must be checked and corrected if necessary. The correct
time is important if the machine is to function on an internal
time schedule and display a proper time and date stamp for
alarms. The time and date will be displayed on the default rotating display of the Navigator module. The time and date can
also be checked and changed under the Time Clock mode as
described below.
point button or a blank button to update the highlighted button
with the source point’s name. Press to add the highlighted
point to the group and return to the table display.
To Remove a Point From a Group Display — From the Point
Data Dialog box, press the REMOVE button and follow the
prompts. The display will return to the Group Display screen
from which the point was removed, and the button corresponding to the deleted point will be blank and disabled.
NAVIGATOR™ DISPLAY MODULE — The Navigator display module provides a mobile user interface to the
ComfortLink control system. The display has up and down arrow keys, an ENTER key, and an ESCAPE key. These keys
are used to navigate through the different levels of the display
structure. Press the ESCAPE key until ‘Select a Menu Item’ is
displayed. Use the up and down arrow keys to move through
the top 11 mode levels indicated by LEDs on the left side of the
display. See Fig. 7. See Table 2 and Appendix B for more details about the display menu structure.
ITEM
HH.MM
Once within a mode or sub-mode, a “>” indicates the
currently selected item on the display screen. Pressing the
ENTER and ESCAPE keys simultaneously will put the
Navigator module into expanded text mode where the full
meaning of all sub-modes, items, and their values can be displayed. Pressing the ENTER and ESCAPE keys when the
display says ‘Select Menu Item’ (Mode LED level) will return
the Navigator module to its default menu of rotating display
items (those items in Run StatusVIEW). In addition, the
password will be disabled, requiring that it be entered again before changes can be made to password protected items. Press
the ESCAPE key to exit out of the expanded text mode.
When a specific item is located, the item name appears on
the left of the display, the value will appear near the middle of
the display and the units (if any) will appear on the far right of
the display. Press the ENTER key at a changeable item and
the value will begin to flash. Use the up and down arrow keys
to change the value, and confirm the value by pressing the
ENTER key.
ITEM EXPANSION
Time of Day
PATH
Time ClockTIME
VALUE
XX.XX
To change the time, press the arrow key to move to the correct hour and press ENTER . The minutes can be changed in a
similar manner.
To check or change the date, the following items must be
checked and changed if necessary.
ITEM
MNTH
DOM
DAY
YEAR
ITEM EXPANSION
Month of Year
Day of Month
Day of Week
Year of Century
PATH
Time ClockDATE
Time ClockDATE
Time ClockDATE
Time ClockDATE
VALUE
WW
XX
YY
ZZ
NOTE: WW is the current month of the controller, (01=January,
02=February, etc.).
XX is the current day of the month
YY is the day of the week, (01=Monday, 02-Tuesday, etc.)
ZZ is the year of the century, (06=2006, 07=2007)
Changing the Unit of Measure — The Navigator display has
two options for unit of measure on the display, English or SI
(metric). The factory default for the units of measure is
English. To change the unit of measure, the following item
must be changed.
Changing item values or testing outputs is accomplished in
the same manner. Locate and display the desired item. Press
ENTER so that the item value flashes. Use the arrow keys to
change the value or state and press the ENTER key to accept
it. Press the ESCAPE key to return to the next higher level of
structure. Repeat the process as required for other items.
ITEM ITEM EXPANSION
PATH
VALUE
OFF – English
ConfigurationDISP ON – SI (Metric)
METR Metric Display
Comf
o
rtLi
Items in the Configuration and Service Test modes are password protected. The words Enter Password will be displayed
when required, with 1111 also being displayed. The default
password is 0111. Use the arrow keys to change each number
and press ENTER to accept the digit. Continue with the
remaining digits of the password. The password can only be
changed through CCN operator interface software such as
ComfortWORKS®, ComfortVIEW™ and Service Tool.
nk
MODE
Run
Alarm
Statu
Statu
s
s
Servi
ce Te
st
Temp
eratur
es
sures
Pres
Setpo
ints
Inputs
Outpu
ts
Confi
gurat
Time
ion
Cloc
k
Opera
Alarm
ting
Power-Up Display — When the Navigator display is powered
up it will display:
ComfortLink
Navigator
By
Carrier
This indicates an initialization period while the Navigator™
display initiates communication with the Main Base Board.
Once communication is established, the default rotating
ESC
Mode
s
s
ENTE
R
a30-3924
Fig. 7 — Navigator Display Module
7
Table 2 — ComfortLink™ Navigator™ Display Menu Structure
RUN
STATUS
Auto Display
(VIEW)
Machine
Starts/Hours
(RUN)
Compressor
Run Hours
(HOUR)
Compressor
Starts
(STRT)
Fan Run
Hours
(FAN)
MODE
SERVICE
SET
TEMPERATURES PRESSURES
INPUTS OUTPUTS CONFIGURATION
TEST
POINTS
Manual
Unit
Circuit A
Cooling General Circuit A
Display
Test Mode
Temperatures
Pressures
Setpoints Inputs
Outputs
Configuration
(TEST)
(UNIT)
(PRC.A)
(COOL) (GEN.I)
(CIR.A)
(DISP)
Quick
Circuit A
Circuit B
Heating
Circuit B
Unit
Test Mode
Temperatures
Pressures
Setpoints
Outputs
Configuration
(QUIC)
(CIR.A)
(PRC.B)
(HEAT)
(CIR.B)
(UNIT)
Circuit B
Circuit C
Misc.
Circuit C
Service
Temperatures
Pressures
Setpoints
Outputs
Configurations
(CIR.B)
(PRC.C)
(MISC)
(CIR.C)
(SERV)
General
Options
Circuit C
Outputs
Configuration
Temperatures
(GEN.O)
(OPTN)
(CIR.C)
Reset,
Demand Limit,
Master/Slave
(RSET)
Compressor
Disable
(CP.UN)
TIME
OPERATING
ALARMS
CLOCK
MODES
Time of Day
Operating Reset Current
(TIME)
Control Type
Alarms
(SLCT)
(R.ALM)
Day, Date
Operating
Current
(DATE)
Modes
Alarms
(MODE)
(ALRM)
Schedule 1
Alarm
(SCH1)
History
(H.ALM)
Schedule 2
(SCH2)
Holidays
(HOLI)
Service
Maintenance
Configuration
(MCFG)
Predictive
Maintenance
(MAIN)
Software Versions
(VERS)
default is set to the highest level. To adjust the backlight of the
Navigator module, enter the LED Test mode of the device.
Changing the Display Language — The Navigator display
has five language options to select from, English, Espanol,
Francais, Portugues, and Translated. The “Translated” option is
not supported at this time. The factory default language is
English. To change the display language, the following item
must be changed.
ITEM
ITEM EXPANSION
LANG Language Selection
PATH
ConfigurationDISP
ITEM ITEM EXPANSION
PATH
TEST Test Display LEDs Configuration ModeDISP
Pressing ENTER will access the TEST point. Pressing
ENTER again will cause the “OFF” to flash. Use the up or
down arrow to change “OFF” to “ON.” Pressing ENTER will
illuminate all LEDs and display all pixels in the view screen.
Pressing the up and down arrow keys simultaneously allows
the user to adjust the display brightness. The display will read:
VALUE
English
Espanol
Francais
Portugues
Translated
NOTE: When the Language Selection (Configuration
DISPLANG) variable is changed, all appropriate display
expansions will immediately change to the new language. The
four letter/digit code will not change. No power-off or control
reset is required when reconfiguring languages.
Adjusting the Contrast — The contrast of the display can be
adjusted to suit ambient conditions. To adjust the contrast, enter
the LED Test mode of the device.
ITEM
TEST
ITEM EXPANSION
Test Display LEDs
PATH
ConfigurationDISP
VALUE
Adjust Brightness
-----------------+
Use the up or down arrow keys to adjust screen brightness.
Press ENTER to accept the change. The Navigator module
will keep this setting as long as it is plugged in to the LEN bus.
CONTROLS
VALUE
General — The 30XA air-cooled liquid chillers contain the
ComfortLink™ electronic control system that controls and
monitors all operations of the chiller. The control system is
composed of several components as listed in the following sections. All machines have a Main Base Board (MBB), Touch Pilot™ module, electronic expansion valve board (EXV), fan
board, Compressor Protection board, Emergency On/Off
switch, and an Enable-Off-Remote Contact switch.
Pressing ENTER will access the TEST point. Pressing
ENTER again will cause the “OFF” to flash. Use the up or
down arrow to change “OFF” to “ON.” Pressing ENTER will
illuminate all LEDs and display all pixels in the view screen.
Pressing ENTER and ESCAPE simultaneously allows the
user to adjust the display contrast. The display will read:
Main Base Board (MBB) — The MBB is the core of
the ComfortLink control system. It contains the major portion
of operating software and controls the operation of the
machine. See Fig. 8. The MBB continuously monitors input/
output channel information received from its inputs and from
all other modules. The MBB receives inputs from status and
feedback switches, pressure transducers and thermistors. The
MBB also controls several outputs. Some inputs and outputs
that control the chiller are located on other boards, but are
transmitted to or from the MBB via the internal communications bus. Information is transmitted between modules via a 3wire communication bus or LEN (Local Equipment Network).
The CCN (Carrier Comfort Network®) bus is also supported.
Connections to both LEN and CCN buses are made at TB3.
Adjust Contrast
- - - -+ - - - - - - - - - - - - - - Use the up or down arrows to adjust the contrast. The
screen’s contrast will change with the adjustment. Press
ENTER to accept the change. The Navigator module will
keep this setting as long as it is plugged in to the LEN (Local
Equipment Network) bus.
Adjusting the Backlight Brightness — The backlight of the
display can be adjusted to suit ambient conditions. The factory
8
For a complete description of Main Base Board inputs and outputs and their channel identifications, see Table 3.
Compressor Protection Module (CPM) — There
is one CPM per compressor. See Fig. 9. The device controls the
compressor contactors, oil solenoid, loading/unloading the
solenoid, motor cooling solenoid (30XA080,082 only) and the
oil separator heater. The CPM also monitors the compressor
motor temperature, high pressure switch, oil level switch, discharge gas temperature, oil pressure transducer, motor current,
MTA (must trip amps) setting and economizer pressure transducer. The CPM responds to commands from the MBB (Main
Base Board) and sends the MBB the results of the channels it
monitors via the LEN (Local Equipment Network). The CPM
has three DIP switch input banks, Switch 1 (S1), Switch 2 (S2),
and Switch 3 (S3). The CPM board DIP switch (S1) configures
the board for the type of starter, the location and type of the
current transformers and contactor failure instructions. See Table 4 for description of DIP switch 1 (S1) inputs. See Appendix
D for DIP switch settings.
The CPM board DIP switch S2 setting determines the must
trip amps (MTA) setting. See Appendix D for DIP switch settings. The MTA setting which is calculated using the settings
S2 must match the MTA setting in the software or an MTA
alarm will be generated.
See below for CPM board DIP switch S3 address information. See Table 5 for CPM inputs and outputs.
CPM-A DIP Switch
Address:
1
OFF
2
OFF
3
OFF
4
OFF
CPM-B DIP Switch
Address:
1
OFF
2
OFF
3
ON
4
OFF
CPM-C DIP Switch
Address:
1
OFF
2
OFF
3
OFF
4
ON
NOTE: The CPM-A and CPM-B DIP switches are for all
units. The CPM-C DIP switches are for 30XA400-500 units.
Electronic Expansion Valve (EXV) Board —
The 30XA080,082 unit has one EXV board. The 30XA090500 units have one EXV board per circuit. See Fig. 10. The
board is responsible for monitoring the suction gas temperature
and economizer gas temperature thermistors. The board also
signals the main EXV and economizer EXV (ECEXV) motors
to open or close. The electronic expansion valve board
responds to commands from the MBB and sends the MBB the
results of the channels it monitors via the LEN (Local Equipment Network). See below for DIP switch information. See
Tables 6 and 7 for EXV inputs and outputs.
EXV BOARD A
(080-500)
DIP SWITCH
Address:
EXV BOARD B
(090-500)
DIP SWITCH
Address:
EXV BOARD C
(400-500)
DIP SWITCH
Address:
CCN
J13
1
2
3
4
5
6
7
8
ON
ON
ON
ON
ON
ON
OFF
ON
1
2
3
4
5
6
7
8
OFF ON ON ON ON ON OFF ON
1
ON
3
4
5
6
SIO
(LEN)
LEN
LEN
+ G –
+ G –
J9C
J9B
LEN
+ G –
221
221
J7C
CH9
J9A
CH8
221
J7D
+ G -
221
D15
TR2
TR3
TR4
TR5
K1
24 VAC
12/11
195
12/11
195
C41
C42
C32
J2A
C43
C34
CH21
CH22 CH23
C35
J2C
RELAY
OUTPUTS
195
195
ANALOG J8
J3 INPUTS
11
195
C16
J4
CH + + CH + CH
15a C C 16a C 16b
CH19
CH20
CH24 CH25 CH26
CH7
DISCRETE
INPUTS
J5A
195
195
C33
J2B
CH6
K2
MOV1
CH1
TR1
CH3
CH2
J6
CH4
THERMISERS
CH5
J7A
PRESSURES
J7B
CCN
J1A
CH10
CH11 CH12 CH13 CH14 CH
15A
LOCATION OF
SERIAL NUMBER
Fig. 8 — Main Base Board
9
7
8
OFF ON ON ON ON OFF ON
J9D
STATUS
J10
2
J5B
J5C
CH17
CH18
a30-4255
Table 3 — Main Base Board Inputs and Outputs
DESCRIPTION
INPUT/OUTPUT
I/O TYPE
DISPLAY MODULE POINT NAME
Power (24 vac supply)
—
—
—
Local Equipment Network
—
—
—
Carrier Communication
Network
—
—
—
Chilled Water Flow Switch
CWFS
Switch
Cooler Flow Switch, LOCK
Demand Limit Switch No. 1
Demand Limit SW1
Switch
Limit Switch 2 Status, DLS1
Circuit A Discharge
Pressure Transducer
DPTA
Pressure Transducer
Discharge Pressure, DP.A
CONNECTION POINT
Pin
Notation
MBB-J1, MBB-J1A,
MBB-J1B
11
24 vac
12
Ground
MBB-J9A, MBB-J9B,
MBB-J9C, MBBJ9D
+
RS485 Port (D+)
G RS485 Port (Gnd)
RS485 Port (D-)
MBB-J12
+
RS485 Port (D+)
G RS485 Port (Gnd)
RS485 Port (D-)
MBB-J5B-CH17
17
MBB-J4-CH13
MBB-J7A-CH6
5V
+5 vdc Ref.
S
Signal
R
Circuit B Discharge
Pressure Transducer
Dual Chiller
LWT Thermistor
Dual Set Point Input
Entering Water Thermistor
Leaving Water Thermistor
Outdoor Air Thermistor
External Chilled
Water Pump Interlock
Circuit A Suction
Pressure Transducer
DPTB
Pressure Transducer
Discharge Pressure, DP.B
Return
MBB-J7C-CH8
5V
+5 vdc Ref.
S
Signal
R
Return
DUAL
5k Thermistor
CHWS Temperature, CHWS
MBB-J6-CH3
Dual Set Point
EWT
LWT
OAT
Switch
5k Thermistor
5k Thermistor
5k Thermistor
Remote Setpoint Switch, DUAL
Cooler Entering Fluid, EWT
Cooler Leaving Fluid, LWT
External Temperature, OAT
MBB-J4-CH12
MBB-J6-CH2
MBB-J6-CH1
MBB-J6-CH4
PMPI
Switch
Electrical Box Interlock, ELEC
MBB-J4-CH15A
SPTA
Pressure Transducer
Suction Pressure, SP.A
5V
S
MBB-J7B-CH7
+5 vdc Ref.
Signal
R
Circuit B Suction
Pressure Transducer
SPTB
Pressure Transducer
Suction Pressure, SP.B
Return
MBB-J7D-CH9
5V
+5 vdc Ref.
S
Signal
R
Return
Unit Status
Remote Contact-Off-Enable
Switch
On/Off Remote Switch, ONOF
MBB-J4-CH11
Alarm Relay
Alert Relay
Cooler Heater
Isolation Valve A
Isolation Valve B
Isolation Valve C (Size 400-500)
Oil Heater A (Size 080, 082 only)
Oil Heater B (Size 080, 082 only)
Pump #1 Interlock
Pump #2 Interlock
ALM R
ALT R
CL-HT
ISVA
ISVB
ISVC
OIL HT_A
OIL HT_A
PMP1
PMP2
Relay
Relay
Contactor
Contactor
Contactor
Contactor
Contactor
Contactor
Alarm Relay Output, ALRM
Alert Relay Output, ALRT
Cooler Heater Command, CO.HT
Ball Valve Position, BVL.A
Ball Valve Position, BVL.B
Ball Valve Position, BVL.C
Circuit A Oil Heater, HT.A
Circuit B Oil Heater, HT.B
MBB-J3-CH24
MBB-J3-CH25
MBB-J3-CH26
MBB-J2A-CH19
MBB-J2A-CH20
MBB-J2C-CH22
MBB-J2C-CH22
MBB-J2C-CH23
Switch
Cooler Pump Run Status, PUMP
MBB-J5C-CH18
LEGEND
I/O
— Input or Output
LWT — Leaving Water Temperature
10
DIP
SWITCH 2
(S2)
C
CH
06 C
CH
10
CH
12
CH
11
R
R
CH02
CH01
DG
MOT
TMP J9 TMP
J11
J2
CH
05
CH
13
CH
14
12
11
J10B
J10A
R
S 5
CH03
R
SMT
S 5
CH04
OIL
PRESS
LOADERS
OLS MOTOR COOLING
151
1
R20 ECO
AUX
PRESS
2
2
151
24 VDC/OLL
151
HPS
151
2x
151
2x
151
561
DIP
SWITCH 3
(S3)
561
561
561
151
102
151
151
151
102
620
0N
102
102
102
1 2 3 4
101
S3
CT1 CT2
LOCATION OF
SERIAL NUMBER
MTA
K40
0N
CT3
1 2 3 4 5 6 7 8
S2
J8
K40
0N
S1
1 2 3 4 5 6 7 8
151
151
J4
100K
100 K
101
101
101
101
– G
3 2
+ – G
1 3 2
J12
SIO
(LEN)
CH
09
102
100 K
SI0 STATUS
(LEN)
+
1
01
J1
02
J5
DIP
STATUS SWITCH 1
(S1)
CH
07
CH
08
J3
a30-4215
Fig. 9 — Compressor Protection Module
Table 4 — DIP Switch 1 (S1) Inputs
DIP SWITCH POSITION
1
FUNCTION
Starter Configuration
Current Transformer (CT) Position
2, 3
Current Transformer (CT) Selection
4, 5, 6
7
8
Contactor Failure Action
Not Used
SETTING
OFF
ON
OFF (2), OFF (3)
ON (2), OFF (3)
OFF (2), ON (3)
ON (2), ON (3)
OFF (4), OFF (5), OFF (6)
ON (4), OFF (5), OFF (6)
OFF (4), ON (5), OFF (6)
ON (4), ON (5), OFF (6)
OFF (4), OFF (5), ON (6)
ON (4), OFF (5), ON (6)
OFF (4), ON (5), ON (6)
ON (4), ON (5), ON (6)
OFF
ON
—
11
MEANING
Across-the-line Start
Wye-Delta Start
CT is located in the Delta of the motor
CT is located in the main line
Reserved for future use
Invalid; will cause MTA configuration alarm
100A/1V CT1
100A/0.503V CT2
100A/0.16V CT3
Invalid; will cause MTA configuration alarm
Invalid; will cause MTA configuration alarm
Invalid; will cause MTA configuration alarm
Invalid; will cause MTA configuration alarm
Invalid; will cause MTA configuration alarm
All units should be off
Used when Shunt Trip is available in the unit
—
Table 5 — Compressor Protection Module Inputs and Outputs*
DESCRIPTION
INPUT/OUTPUT
I/O TYPE
DISPLAY MODULE POINT NAME
Power (24 vac supply)
—
—
—
Local Equipment Network
—
—
—
Circuit X High Pressure Switch
HPS-X
Switch
Not available
CONNECTION POINT
Pin
Notation
CPM-X-J1
11
24 vac
12
Ground
CPM-X-JP12
1
RS485 Port (D+)
2
RS485 Port (Gnd)
3
RS485 Port (D-)
CPM-X-J12
1
RS485 Port (D+)
2
RS485 Port (Gnd)
3
RS485 Port (D-)
CPM-X-J7-CH05
1
2
CPM-X-J6-CH06
Oil Level Switch
Oil LS X
Switch
Circuit X Oil Solenoid, OLS.X
1
2
Must Trip Amps†
MTA (S2)
8-Pin DIP Switch
Must Trip Amps, MTA.X
Configuration Switch†
S1
8-Pin DIP Switch
S1 Config Switch, C.SW.X
Compressor X Motor Temperature
MTR-X
NTC Thermistor
Motor Temperature, CTP.X
CPM-X-J9-CH01
1
2
CPM-X-J9-CH02
Compressor X Discharge Gas Temperature
DGT X
NTC Thermistor
Discharge Gas Temp, DGT.X
1
2
CPM-X-J10B-CH04
5V
Oil Pressure Transducer
OPT X
Pressure Transducer
Oil Pressure, OP.X
+ 5 vdc ref
S
Signal
R
Return
CPM-X-J10A
5V
Economizer Pressure Transducer
EPT X
Pressure Transducer
Economizer Pressure, ECP.X
+ 5 vdc ref
S
Signal
R
Return
CPM-X-J8-CH01
Compressor Current X Phase A
Current Sensor
CUR.A
1
2
CPM-X-J8-CH02
Compressor Current X Phase B
Current Sensor
CUR.B
1
2
CPM-X-J8-CH3
Compressor Current X Phase C
Current Sensor
CUR.C
1
2
CPM-X-J1-CH07
Compressor X 1M Contactor
C X 1M
Contactor
Compressor Output, CP.X
1
2
Compressor X 2M Contactor
C X 2M
Contactor
Not available
1
2
Compressor X S Contactor
CXS
Contactor
Not available
1
2
Oil Heater Relay X (090-500 Only)
Oil HTR X
Contactor
Oil Heater Output, HT.X
1
2
Oil Solenoid X
Oil solenoid-X
Solenoid
Oil Solenoid Output, OLS.X
1
2
Load Solenoid X
Loading Solenoid-X
Solenoid
Slide Valve 1 Output, SL1.X
Unload Solenoid X
Unloading Solenoid-X
Solenoid
Slide Valve 2 Output, SL2.X
1
2
Gas Cooling Solenoid X (080,082 Only)
Gas Cooling Solenoid-X
Solenoid
DGT Cooling Solenoid, DGT.X
1
2
CPM-X-J2-CH8
CPM-X-J2-CH9
CPM-X-J2-CH10
CPM-X-J2-CH12
CPM-X-J2-CH13
1
CPM-X-J2-CH14
CPM-X-J2-CH10
*“X” denotes the circuit, A, B or C.
†See Appendix D for MTA settings.
12
COMM J4
3 2 1
- G +
1
U2
SB
Q7
S1
ON
1
D15
C10
5
U6
THB
2
L1
3
U1
4
C37
712
D2
THA
C39
J3
R9
Q4
C11
Q5
C25
TEMP
100
D1
C49
100K
4
Q12
Q17
Q15
Q20
Q22
Q27
Q25
6
2
5
Q10
7
1
J2B
3
3
4
EXVB
2
257-01
D8
2
J2A
D9
3
4
EXVA
5
8
D29
SI0
(LEN)
STATUS
1
DIP
SWITCH
R2
L3
100
L2
100
100K
R3
Q30
Q2
Q1
L4
U5
G2
U4
Q37
Q42
Q35
Q45
D5
+
C16
C15
D6
D4
LOCATION OF
SERIAL NUMBER
C17
MOV1
J1
24VAC
12/11
a30-4216
Fig. 10 — EXV Board
13
Table 6 — EXVA Board Inputs and Outputs (30XA080,082)
DESCRIPTION
INPUT/OUTPUT
I/O TYPE
DISPLAY MODULE POINT NAME
Power (24 vac supply)
—
—
—
Local Equipment Network
—
—
—
Circuit A Suction Gas Thermistor
SGTA
5k Thermistor
Compressor Suction Temp, SGT.A
Circuit B Suction Gas Thermistor
SGTB
5k Thermistor
Compressor Suction Temp, SGT.B
Circuit A EXV
EXV-A
Stepper Motor
EXV Position, EXV.A
Circuit B EXV
EXV-B
Stepper Motor
EXV Position, EXV.B
CONNECTION POINT
Pin
Notation
EXVA-J1
11
24 vac
12
Ground
EXVA-J4
1
RS485 Port (D+)
2 RS485 Port (Gnd)
3
RS485 Port (D–)
EXVA-J3
TH
A
EXVA-J3
TH
B
EXVA-J2A
1
2
3
4
EXVA-J2B
1
2
3
4
Table 7 — EXV A,B,C Board Inputs and Outputs* (30XA090-500)
DESCRIPTION
INPUT/OUTPUT
I/O TYPE
DISPLAY MODULE POINT NAME
Power (24 vac supply)
—
—
—
Local Equipment Network
—
—
Circuit X Suction Gas Thermistor
SGT X
5k Thermistor
Compressor Suction Temp, SGT.X
Circuit X Economizer Gas Thermistor
ECT X
5k Thermistor
Economizer Gas Temp, ECT.X
Circuit X EXV
EXV-X
Stepper Motor
EXV Position, EXV.X
Circuit X Economizer EXV
ECEXV-X
Stepper Motor
Cir X Economizer EXV Pos, ECO.X
*“X” denotes the circuit, A, B or C.
14
—
CONNECTION POINT
Pin
Notation
EXVX-J1
11
24 vac
12
Ground
EXVX-J4
1
RS485 Port (D+)
2 RS485 Port (Gnd)
3
RS485 Port (D–)
EXVX-J3
TH
A
EXVX-J3
TH
B
EXVX-J2A
1
2
3
4
EXVX-J2A
1
2
3
4
Fan Boards — At least one fan board is installed in each
unit. See Fig. 11 and 12. There are two types of fan boards.
One with and one without an analog output signal for the low
ambient temperature head pressure control fan speed controllers. If a unit does not have low ambient temperature head pressure control installed, it will not have the analog connection terminals. The fan board responds to commands from the MBB
and sends the MBB the results of the channels it monitors via
the Local Equipment Network (LEN). See below for fan board
A, B and C DIP switch addresses. See Tables 8-10 for inputs
and outputs.
FAN BOARD
(080,082)
DIP SWITCH
Address:
1
2
3
4
5
7
8
OFF ON OFF OFF ON OFF ON OFF
FAN BOARD A
(090-500)
DIP SWITCH
Address:
1
2
OFF
ON
FAN BOARD B
(140-500)
DIP SWITCH
Address:
FAN BOARD C
(400-500)
DIP SWITCH
Address:
1
3
4
OFF OFF
2
3
4
5
6
7
8
ON
OFF
ON
OFF
5
6
7
8
ON ON OFF OFF ON OFF ON OFF
1
2
OFF OFF
3
4
5
6
7
8
ON
OFF
ON
OFF
ON
OFF
a30-4046
DIP SWITCH
LOCATION OF
SERIAL NUMBER
6
STATUS SIO (LEN)
Q5
8
L2
100K
100K
–
3
U2
Q12
L3
Q60
G
2
100K
D3
Q1
+
1
U1
24 VAC
L5
Q11
Q10
U9
U8
–
3
U10
U7
U6
U5
U21
+
1
7
G
2
6
J9
5
D6
4
Y1
J1
3
S1
2
1
D5
D7
D8
ON
U4
J2
CH1
TR2
CH2
TR3
TR4
J3
CH4
CH3
TR5
TR6
TR7
TR8
CH5
CH6
CH7
CH8
CH9
CH10
CH13
CH14
JP2
C61
J4
TR1
CH13
D12 JP1
CH12
CH11
Fig. 11 — Fan Board (AUX 1) with Low Ambient Temperature Head Pressure Control
LOCATION OF
SERIAL NUMBER
DIP SWITCH
D7
Q5
STATUS SIO (LEN)
6
7
8
L2
U1
24 VAC
Q1
+
1
5
G
2
4
100K
100K
D3
100K
Q12
U6
–
3
Q11
Q10
U9
U8
Q2
U5
G
2
Q9
Q3
Q7
C3
U2
+
1
–
3
3
D6
2
Y1
S1
J1
1
J9
D5
ON
Q13
D4
J4
J2
TR1
TR2
TR3
TR4
TR5
TR6
TR7
TR8
J3
a30-4047
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
Fig. 12 — Fan Board (AUX 2) without Low Ambient Temperature Head Pressure Control
15
Table 8 — Fan Board A Outputs (30XA080-122)
DESCRIPTION
INPUT/OUTPUT
I/O TYPE
DISPLAY MODULE POINT NAME
Power (24 vac supply)
—
—
—
Local Equipment Network
—
—
—
Circuit A Low Ambient Temperature
Head Pressure Control Speed Signal
MM-A*
0-10 VDC
Head Press Actuator Pos, SPD.A
Circuit B Low Ambient Temperature
Head Pressure Control Speed Signal
MM-B*
0-10 VDC
Head Press Actuator Pos, SPD.B
Fan Contactor A1
Fan Contactor A2
Fan Contactor A3
FCA1
FCA2
FCA3
Contactor
Contactor
Contactor
Fan Contactor A4
FCA4
Contactor
Fan Contactor B1
Fan Contactor B2
Fan Contactor B3
FCB1
FCB2
FCB3
Contactor
Contactor
Contactor
Fan Contactor B4
FCB4
Contactor
CONNECTION POINT
Pin
Notation
FBA-J1
11
24 vac
12
Ground
FBA-J9
+
RS485 Port (D+)
G RS485 Port (Gnd)
RS485 Port (D-)
+
RS485 Port (D+)
G RS485 Port (Gnd)
RS485 Port (D-)
FBA-CH9
+
Signal
Ground
FBA-CH10
+
Signal
Ground
FBA-J2-CH1
FBA-J2-CH2
FBA-J2-CH3
FBA-J2-CH4
(090-122)
FBA-J3-CH5
FBA-J3-CH6
FBA-J3-CH7
FBA-J3-CH8
(090-122)
*Output only on low ambient temperature head pressure control (AUX1).
Table 9 — Fan Board X Outputs (30XA140-352)
DESCRIPTION
INPUT/OUTPUT
I/O TYPE
DISPLAY MODULE POINT NAME
Power (24 vac supply)
—
—
—
Local Equipment Network
—
—
—
Circuit X Low Ambient Temperature
Head Pressure Control
Speed Signal
MM-n*
0-10 VDC
Head Press Actuator Pos, SPD.X
Fan Contactor X1
Fan Contactor X2
Fan Contactor X3
Fan Contactor X4
Fan Contactor X5
Fan Contactor X6
Fan Contactor X7
Fan Contactor X8
FCX1
FCX2
FCX3
FCX4
FCX5
FCX6
FCX7
FCX8
Contactor
Contactor
Contactor
Contactor
Contactor
Contactor
Contactor
Contactor
*Output only on units with low ambient temperature head pressure control installed (AUX1).
NOTES:
1. Fan Board B used on 30XA140-350.
2. “X” indicates circuit A or circuit B.
3. See page 109, Fig. 65 for which contactor is used with circuit A
or B.
16
CONNECTION POINT
Pin
Notation
FBX-J1
11
24 vac
12
Ground
FBX-J9
+
RS485 Port (D+)
G RS485 Port (Gnd)
RS485 Port (D-)
+
RS485 Port (D+)
G RS485 Port (Gnd)
RS485 Port (D-)
FBX-CH9
+
Signal
Ground
FBX-J2-CH01
FBX-J2-CH02
FBX-J2-CH03
FBX-J2-CH04
FBX-J3-CH05
FBX-J3-CH06
FBX-J3-CH07
FBX-J3-CH08
Table 10 — Fan Board C Inputs and Outputs (30XA400-500)
CONNECTION POINT
(Unit Size)
Pin
Notation
FBC-J1
11
24 vac
12
Ground
FBC-J9
+
RS485 Port (D+)
G RS485 Port (Gnd)
RS485 Port (D-)
+
RS485 Port (D+)
G RS485 Port (Gnd)
RS485 Port (D-)
DESCRIPTION
INPUT/OUTPUT
I/O TYPE
DISPLAY MODULE POINT NAME
Power (24 vac supply)
—
—
—
Local Equipment Network
—
—
—
Circuit C Discharge
Pressure Transducer
Circuit C Suction
Pressure Transducer
DPTC
Pressure Transducer
Discharge Pressure, DP.C
FBC-J7-CH13
SPTC
Pressure Transducer
Suction Pressure, SP.C
FBC-J8-CH14
Circuit C Low Ambient
Temperature Head Pressure
Control Speed Signal
MM-C
0-10 VDC
Head Press Actuator Pos, SPD.C
Fan Contactor C1
Fan Contactor C2
Fan Contactor C3
Fan Contactor C4
Fan Contactor C5
Fan Contactor C6
Fan Contactor C7
Fan Contactor C8
FCC1
FCC2
FCC3
FCC4
FCC5
FCC6
FCC7
FCC8
Contactor
Contactor
Contactor
Contactor
Contactor
Contactor
Contactor
Contactor
FBC-CH9
Signal
Ground
FBC-J2-CH1
FBC-J2-CH2
FBC-J2-CH3
FBC-J2-CH4
FBC-J3-CH5
FBC-J3-CH6
FBC-J3-CH7
FBC-J3-CH8
+
-
limit, and other functions according to the inputs received. See
Table 11.
Enable-Off-Remote Contact Switch (SW1) —
This switch is installed in all units and provides the owner and
service person with a local means of enabling or disabling the
machine. It is a 3-position switch and it is used to control the
chiller. When switched to the Enable position, the chiller will
be under its own control. When switched to the Off position,
the chiller will shut down. When switched to the Remote Contact position, a field-installed dry contact can be used to start
the chiller. The contacts must be capable of handling a 24-vac,
50-mA load. In the Enable and Remote Contact (dry contacts
closed) positions, the chiller is allowed to operate and respond
to the scheduling configuration, CCN configuration, and set
point data.
For units with a Touch Pilot™ display, the position of the
Enable/Off/Remote contact switch is ignored except when the
“remote mode” control type is selected. Refer to the Machine
Control Methods section on page 22 for more details.
CAUTION
Care should be taken when interfacing with other manufacturer’s control systems due to possible power supply differences, full wave bridge versus half wave rectification,
which could lead to equipment damage. The two different
power supplies cannot be mixed. ComfortLink™ controls
use half wave rectification. A signal isolation device should
be utilized if incorporating a full wave bridge rectifier signal generating device is used.
Hot Gas Bypass/Pump Board — The hot gas bypass (HGBP) and pump board controls the ON/OFF of the
HGBP solenoids and pump contactors, and responds to MBB
commands via the LEN connection. Hot gas bypass is available as a factory-installed option or as a field-installed accessory for 30XA080-500, and the pump package is available as
factory-installed option for sizes 30XA090-162. See Fig. 14.
The board is not required for single pump operation. See below
for DIP switch information. See Table 12 for HGBP/Pump
board inputs and outputs.
Emergency On/Off Switch (SW2) — This switch is
installed in all units. The Emergency On/Off switch should
only be used when it is required to shut the chiller off immediately. Power to all modules is interrupted when this switch is
off and all outputs from these modules will be turned off.
Energy Management Module (EMM) — The EMM
is available as a factory-installed option or as a field-installed
accessory. See Fig. 13. The EMM receives 4 to 20 mA inputs
for the temperature reset, cooling set point and demand limit
functions. The EMM also receives the switch inputs for the
field-installed second stage 2-step demand limit and ice done
functions. The EMM communicates the status of all inputs
with the MBB, and the MBB adjusts the control point, capacity
HGBP/Pump
BOARD
DIP SWITCH
Address:
17
1
2
3
ON
ON
ON
4
5
6
7
8
OFF ON OFF ON OFF
Table 11 — Energy Management Module (EMM) Inputs and Outputs
INPUT/OUTPUT
4-20 mA Demand Limit
4-20 mA Temperature
Reset/Cooling Setpoint
Demand Limit SW2
Ice Done
Occupancy Override
Remote Lockout Switch
SPT
% Total Capacity
RUN R
SHD R
DESCRIPTION
4-20 mA Demand Limit
4-20 mA Temperature Reset/
Cooling Set point
Demand Limit Step 2
Ice Done Switch
Occupied Schedule Override
Chiller Lockout
Space Temperature Thermistor
Percent Total Capacity Output
Run Relay
Shutdown Relay
I/O TYPE
4-20 mA*
4-20 mA*
DISPLAY MODULE POINT NAME
Limit 4-20 mA Signal, DMD
Reset/Setpnt 4-20 mA Signal, RSET
CONNECTION POINT
EMM-J7B-CH6
EMM-J7A-CH5
Switch Input
Switch Input
Switch Input
Switch Input
10k Thermistor
0-10 vdc
Relay
Relay
Switch Limit Setpoint 2, DLS2
Ice Done Storage Switch, ICE.D
Occupied Override Switch, OCCS
Remote Interlock Switch, RLOC
Optional Space Temp, SPT
Chiller Capacity Signal, CATO
Running Status, RUN
Shutdown Indicator State, SHUT
EMM-J4-CH9
EMM-J4-CH11A
EMM-J4-CH8
EMM-J4-CH10
EMM-J6-CH2
EMM-J8-CH7
EMM-J3-CH25
EMM-J3-CH24
* A field-supplied 1/2 watt 250 ohm resistor is required across terminals TB6-1,2 (CH6) and/or TB6-3, 4 (CH5).
+ G -
+ G -
SIO LEN
100K
CH 7
221
SIO LEN
221
221
221
100K
100K
CH 6
J8
CH 5
100K
J7B
J7A
J6
CH
12
CH
13
CH
14
CH
15
CH
1
CH
2
CH
3
CH
4
100K
CH
11b
24 VAC
12 11
J5
CH
J1
J2A
CH CH
17 16
CH
17
CH
18
CH
19
CH
20
CH
21
CH
22
CH
23
J2B
J3
Fig. 13 — Energy Management Module
18
J4
a30-4465
Table 12 — Hot Gas Bypass/Pump Board Inputs and Outputs
CONNECTION POINT
DESCRIPTION
INPUT/OUTPUT
I/O TYPE
DISPLAY MODULE POINT NAME
—
—
—
—
—
—
MLV-A
MLV-B
MLV-C
PMP1
PMP2
Solenoid Valve
Solenoid Valve
Solenoid Valve
Contactor
Contactor
Hot Gas Bypass A Output, HGB.A
Hot Gas Bypass B Output, HGB.B
Hot Gas Bypass C Output, HGB.C
Water Exchanger Pump 1, PMP.1
Water Exchanger Pump 2, PMP.2
Pin
Notation
HGBP/PMP-J1
11 24 vac
12 Ground
HGBP/PMP-J9
+ RS485 Port (D+)
G RS485 Port (Gnd)
RS485 Port (D-)
HGBP/PMP-J2-CH3
HGBP/PMP-J2-CH4
HGBP/PMP-J2-CH5
HGBP/PMP-J2-CH1
HGBP/PMP-J2-CH2
Power (24 vac supply)
Local Equipment Network
LOCATION OF
SERIAL NUMBER
DIP SWITCH
D7
Q5
STATUS SIO (LEN)
D5
ON
6
7
8
L2
U1
24 VAC
Q1
+
1
5
G
2
4
100K
100K
D3
100K
Q12
U6
–
3
Q11
Q10
U9
U8
Q2
U5
G
2
Q9
Q3
Q7
C3
U2
+
1
–
3
3
D6
2
Y1
S1
J1
1
J9
Circuit A Minimum Load Control
Circuit B Minimum Load Control
Circuit C Minimum Load Control
Pump #1 Starter
Pump #2 Starter
Q13
D4
J4
J2
TB1
TB2
TB3
TB4
TB5
TB6
TB7
TB8
CH5
CH6
CH7
CH8
J3
a30-4047
CH1
CH2
CH3
CH4
Fig. 14 — Hot Gas Bypass/Pump Board
Base Board (MBB) is supplied with the current software. If
necessary, reload current software. If the problem still persists,
replace the MBB. A red LED that is lit continuously or blinking at a rate of once per second or faster indicates that the board
should be replaced.
GREEN LED — All boards have a green LEN (SIO) LED
which should be blinking whenever power is on. If the LEDs
are not blinking as described check LEN connections for
potential communication errors at the board connectors. See
Input/Output Tables 3-12 for LEN connector designations. A
3-wire bus accomplishes communication between modules.
These 3 wires run in parallel from module to module. The J9A
connector on the MBB provides communication directly to the
Navigator™ display module.
YELLOW LED — The MBB has one yellow LED. The
Carrier Comfort Network® (CCN) LED will blink during times
of network communication.
Local Equipment Network — Information is transmitted between modules via a 3-wire communication bus or
LEN (Local Equipment Network). External connection to the
LEN bus is made at TB3.
Board Addresses — All boards (except the Main Base
Board and Energy Management Module Board) have
8-position DIP switches.
Touch Pilot™ Display — The Touch Pilot display port
connections are shown in Table 13. Wiring is shown in Fig. 15.
Control Module Communication
RED LED — Proper operation of the control boards can be
visually checked by looking at the red status LEDs (lightemitting diodes). When operating correctly, the red status
LEDs will blink in unison at a rate of once every 2 seconds. If
the red LEDs are not blinking in unison, verify that correct
power is being supplied to all modules. Be sure that the Main
19
It is important when connecting to a CCN communication
bus that a color-coding scheme be used for the entire network
to simplify the installation. It is recommended that red be used
for the signal positive, black for the signal negative, and white
for the signal ground. Use a similar scheme for cables containing different colored wires.
At each system element, the shields of its communication
bus cables must be tied together. If the communication bus is
entirely within one building, the resulting continuous shield
must be connected to a ground at one point only. If the communication bus cable exits from one building and enters another,
the shields must be connected to grounds at the lightning
suppressor in each building where the cable enters or exits the
building (one point per building only). To connect the unit to
the network:
1. Turn off power to the control box.
2. Cut the CCN wire and strip the ends of the red (+), white
(ground), and black (–) conductors. (Substitute appropriate colors for different colored cables.)
3. Connect the red wire to (+) terminal on TB3 of the plug,
the white wire to COM terminal, and the black wire to the
(–) terminal.
4. The RJ14 CCN connector on TB3 can also be used, but is
only intended for temporary connection (for example, a
laptop computer running Service Tool).
Table 13 — Touch Pilot™ Display Port
Connections
CONNECTOR
J1 (Power)
J2 (COM1)
J3 (RJ11)
PIN
1
2
3
1
2
3
1
2
3
4
5
6
FUNCTION
24VAC +
24VAC Earth Ground
RS485 Port (D+)
RS485 Port (GND)
RS485 Port (D-)
24VAC (+)
RS485 Port (D+)
RS485 Port (GND)
Unused (no connect)
RS485 Port (D-)
24VAC(-)
Carrier Comfort Network® (CCN) Interface —
All 30XA units can be connected to the CCN, if desired. The
communication bus wiring is a shielded, 3-conductor cable
with drain wire and is field supplied and installed. The system
elements are connected to the communication bus in a daisy
chain arrangement. The positive pin of each system element
communication connector must be wired to the positive pins of
the system elements on either side of it. The negative and signal ground pins of each system element must also be wired in
the same manner. Wiring connections for CCN should be made
at TB3. Consult the CCN Contractor’s Manual for further information. See Fig. 16.
NOTE: Conductors and drain wire must be 20 AWG (American Wire Gage) minimum stranded, tinned copper. Individual
conductors must be insulated with PVC, PVC/nylon, vinyl,
Teflon, or polyethylene. An aluminum/polyester 100% foil
shield and an outer jacket of PVC, PVC/nylon, chrome vinyl,
or Teflon with a minimum operating temperature range of
–20 C to 60 C is required. See Table 14 for recommended wire
manufacturers and part numbers.
IMPORTANT: A shorted CCN bus cable will prevent
some routines from running and may prevent the unit
from starting. If abnormal conditions occur, disconnect the CCN bus. If conditions return to normal,
check the CCN connector and cable. Run new cable if
necessary. A short in one section of the bus can cause
problems with all system elements on the bus.
Remote Alarm and Alert Relays — The 30XA chiller can be equipped with a remote alert and remote alarm
annunciator contacts. Both relays connected to these contacts
must be rated for a maximum power draw of 10 va sealed,
25 va inrush at 24 volts. The alarm relay, indicating that the
complete unit has been shut down, can be connected to TB5-12
and TB5-13. Refer to unit wiring diagrams. For an alert relay,
indicating that at least 1 circuit is off due to the alert, a fieldsupplied and installed relay must be connected between MBBJ3-CH25-3 and TB5-13. The action of the alarm and alert relays can be reversed from normally open to normally closed by
using the Reverse Alarms Relay configuration (Reverse
Alarms Relay, RV.AL).
Table 14 — CCN Communication Bus Wiring
MANUFACTURER
Alpha
American
Belden
Columbia
Manhattan
Quabik
PART NUMBER
Regular Wiring
Plenum Wiring
1895
—
A21451
A48301
8205
884421
D6451
—
M13402
M64430
6130
—
a30-4082
Fig. 16 — ComfortLink™ CCN Communication Wiring
Fig. 15 — Touch Pilot™ Display Wiring
20
Fig. 16 — ComfortLink™ CCN Communication Wiring
Service Tool or ComfortVIEW™ software. The tables are the
CtrlID (Controller Identification) configuration table and the
USERCONF (User Configuration) table. See Tables 15 and 16.
NOTE: Always perform an Upload to obtain the latest configuration before making configuration table changes.
CONFIGURATION
Touch Pilot™ Operation Configuration
Tables — The Touch Pilot display operation is controlled by
configuration information entered in the following configuration tables. These tables are accessible by using Network
Table 15 — Touch Pilot Controller Identification Configuration Table
CONTROLLER ID DATA
BLOCK NO.
Device Name
1
Local address
Bus number
2
2
Device (driver) type
2
Primary baud rate
Secondary baud rate
3
3
Device description
4
Device location
4
Software part number
Model number
Serial number
Reference number
4
4
4
4
Broadcast address processing list (primary)
5
Broadcast address processing list (secondary)
5
VALUE AND RANGE
CHILLDSP
8 character Name field
115
0
0 = Non-bridge
3 = Broadcast Acknowledger
38400
38400
Global Chiller Display
24 character text field
(Blank)
24 character text field
CESR-131363-01
(Blank)
(Blank)
Version 1.0
241-251, 254, 255 enabled
241-255 enabled/disabled
none
QUALIFIERS
Default
Optional
Default
Default
Default
Optional
Default
Fixed
Default
Optional
Default
Optional
Fixed
Fixed
Fixed
Fixed
Defaults
Optional
Not applicable
Table 16 — Touch Pilot™ User Configuration (USERCONF) Table
DESCRIPTION
Backlight always on?
Full access password
Limited access password
Active language
Time format
Date format
Units base
Contrast control
Network mode
Network settings
Alarm acknowledger
Broadcast acknowledger
Equipment CCN address
Bus number
Element number
Control variables
Equipment status (Not Used)
Equipment start/stop (Not Used)
Alarm status (Not Used)
Alarm reset (Not Used)
LIMITS
No - Yes
0 - 9999
0 - 9999
0-1
0-1
0-2
US - Metric
Manual - Auto
0-1
NAME
BACKLITE
PSWDFULL
PSWDLMTD
ACTLANG
TIMEFMT
DATEFMT
UNITBASE
CONTRAST
NETWORK
DEFAULT
No
3333
2222
0
0
0
US
Auto
0
No - Yes
No - Yes
ALARMACK
BROADACK
No
No
0 - 239
1 - 239
EQUIPBUS
EQUIPELE
0
1
Name char 8
Name char 8
Name char 8
Name char 8
EQSTATUS
STARSTOP
ALSTATUS
ALRESET
NOT USED
NOT USED
NOT USED
NOT USED
21
UNITS
such as ComfortVIEW™ software, the Autodial Gateway or
TeLINK is already set as the alarm acknowledger for the CCN
network then this decision should be set to No.
NOTE: The display must be in Network mode and connected
to the primary CCN bus and this decision set to Yes for alarm
acknowledgement to be enabled.
Allowable Entries: No
Yes
Default Value:
No
BROADCAST ACKNOWLEDGER — This configuration
is used to indicate whether the Touch Pilot display will act as
the broadcast acknowledger for its CCN bus. There can be only
one broadcast acknowledger per CCN bus.
NOTE: The display must be in Network mode and this decision set to Yes for broadcast acknowledgement to be enabled.
Allowable Entries: No
Yes
Default Value:
No
EQUIPMENT CCN ADDRESS — When in equipment
mode (USERCONF Table’s Network Mode decision is set to
Disable), the Bus Number and Element Number decisions are
used to specify the CCN address of the piece of equipment to
communicate with. An Attach or power cycle must be
performed for changes to take effect. These decisions will be
ignored when the display is connected to the LEN bus or in
Network mode. In Network mode, specify the bus and element
number the equipment communicates with using the display’s
Attach function.
NOTE: In Network mode, these configurations will be overwritten with the default device address if it is changed through
the Attach process.
BUS NUMBER — This configuration is used to specify the
Equipment Controller bus number.
Allowable Entries: 0 through 239
Default Value:
0
ELEMENT NUMBER — This configuration is used to specify the Equipment Controller element number.
Allowable Entries: 1 through 239
Default Value:
1
BACKLIGHT ALWAYS ON? — This configuration is used
to keep the backlight on continuously or to turn it off after 60
seconds with no activity.
Allowable Entries: No/Yes (No=0 or Yes=1)
Default Value:
No
FULL ACCESS PASSWORD — This configuration is used
to specify the full access password. Refer to Table 1, Setup
Menu, for additional information on passwords.
Allowable Entries: 0 through 9999
Default Value:
3333
LIMITED ACCESS PANEL — This configuration is used to
specify the limited access password.
Allowable Entries: 0 through 9999
Default Value:
2222
ACTIVE LANGUAGE — This configuration is used to specify the display’s active language. All translatable text will be
displayed in this language.
Allowable Entries: 0, 1
Default Value:
0
TIME FORMAT — This configuration is used to specify the
format for display of time.
Allowable Entries: 0 = H:MM AM/PM without leading zero
1 = HH:MM with leading zero when
necessary
Default Value:
0
DATE FORMAT — This configuration is used to specify the
format for display of date.
Allowable Entries: 0 = MM-DD-YYYY with leading zero
when necessary
1 = DD-MM-YYYY with leading zero
when necessary
2 = YYYY-MM-DD
Default Value:
0
UNITS BASE — This configuration is used to specify the format of the units of measure.
Allowable Entries: U.S.
Metric
Default Value:
U.S.
CONTRAST CONTROL — This configuration is used to enable or disable the display’s auto contrast adjustment feature.
When enabled, the display’s contrast will be automatically adjusted as required, based on temperature.
Allowable Entries: Manual
(Auto Contrast Adjustment Disabled)
Auto
(Auto Contrast Adjustment Enabled)
Default Value:
Auto
NETWORK MODE — This configuration is used to set the
display’s operating mode. For additional information on operating mode, refer to Display in the Table Setup Menu. This decision will be ignored and the mode will default to Equipment
when the display is connected to a device (the LEN Bus).
NOTE: A power cycle is required for this decision to take
effect.
Allowable Entries: 0 (Disable) = Equipment Mode
1 (Enable) = Network Mode
Default Value:
0 (Disable)
ALARM ACKNOWLEDGER — This configuration is used
to specify whether the Touch Pilot™ display will act as the
alarm acknowledger for the CCN. There can be only one alarm
acknowledger per CCN. Therefore, if another CCN device
Machine Control Methods — Three variables control how the machine operates. These variables control the
On-Off function, set point operation, and Heat-Cool operation.
Machine On/Off Control — Machine On/Off control
depends on which interface display is used. The control is different for Touch Pilot™ or Navigator™ displays. Select the
correct configuration procedure below based on which interface is being used.
TOUCH PILOT MACHINE CONTROL — Machine On/Off
control is determined locally by pushing the Start/Stop button
on the Touch Pilot display. Pressing this button will cause the
Equipment Start screen to be displayed. See Fig. 17.
Table 17 summarizes the unit control type and stop or go
status with regard to the following parameters:
• Operating type: this is selected by using the start/stop button
on the front of the user interface.
• Remote start/stop contacts: these contacts are used when the
unit is in remote operating type (Remote mode).
• CHIL_S_S: this network command variable relates to the
chiller start/stop when the unit is in CCN control (CCN
mode). When this variable forced to Disable, then the unit is
stopped. When this variable is forced to Enable, then the
unit runs in accordance with schedule 1.
22
Control Type will be Local. The Operating Type variable
will change to L-Sched (Local Schedule).
The schedules consist of 8 user-configurable occupied time
periods. The control supports time schedules for local control,
remote control, and ice building. These time periods can be
flagged to be in effect or not in effect on each day of the week.
The day begins at 00.00 and ends at 24.00. The machine will be
in unoccupied mode unless a scheduled time period is in effect.
If an occupied period extends past midnight, the occupied
period will automatically end at 24:00 hours (midnight) and the
new occupied period must be programmed to begin at 00:00
hours.
In the following example, the occupied period starts at 6:00
AM, Monday through Friday and 10:00 AM on Saturday and
Sunday. The occupied time ends at 6:30 PM on Monday
through Friday and 2:00 PM on Saturday and Sunday. See
Fig. 18.
• Start/Stop schedule: occupied or unoccupied status of the
unit as determined by the chiller start/stop program (Schedule 1).
• Master control type: This parameter is used when the unit is
the master unit in a two chiller lead/lag arrangement. The
master control type determines whether the unit is to be
controlled locally, remotely or through CCN (this parameter
is a Service configuration).
• CCN emergency shutdown: if this CCN command is activated, it shuts the unit down whatever the active operating
type.
• General alarm: the unit is totally stopped due to failure.
Local Mode — To start the machine in local mode, press the
Start/Stop button on the Touch Pilot display. The Equipment
Start screen will be displayed. Select Local On. The control
will ignore the position of Enable/Off/Remote Contact switch
and all CCN network force commands, except an Emergency
Stop Command. The Run Status variable, indicating the current status of the machine, will change to RUNNING, DELAY
or READY. The Chiller Occupied? variable will change to
YES. The Control Type variable indicates the type of control.
For this configuration, Control Type will be Local. The Operating Type variable will change to L-On (Local On).
Local Schedule — To start the machine with a local schedule,
press the Start/Stop button on the Touch Pilot display. The
Equipment Start screen will be displayed. Select Local Schedule. The unit will start and stop according to the schedule defined in the Time Schedule menu. Two Internal Time Schedules are available and must be field programmed. Time
Schedule 1 is used for single set point On-Off control. Time
Schedule 2 is used for Dual Set Point/Occupied-Unoccupied set point control. The control will ignore the position of
Enable/Off/Remote Contact switch and all CCN network force
commands, except the Emergency Stop Command.
The Run Status variable will indicate the current status of
the machine — OFF, RUNNING, DELAY, or READY. The
Chiller Occupied? variable will indicate the occupied state of
the machine according to Time Schedule 1 and will be either
YES (occupied) or NO (unoccupied). The Control Type variable will indicate the type of control. For this configuration,
Fig. 17 — Equipment Start Screen
Table 17 — Touch Pilot™ Start/Stop Control
ACTIVE OPERATING TYPE
Remote
Local Local
Local
Remote CCN Master CHIL_S_S Start/Stop
On
On
Schedule Mode Mode Mode
Variable
Contact
Active
Active
Active
Off
Active
Active
Off
Active
Active
Active
Off
Active
Active
Off
Active
Active
Active
Active
On Cool
Active
On
Active
Active
On Cool
Active
On
-
PARAMETER STATUS
CONTROL
Start/Stop
CCN
Master Unit
TYPE
Schedule
Emergency General
Control Type
Alarm
Mode
Shutdown
Active
Yes
Local
Unoccupied
Local
Remote
Unoccupied
Remote
CCN
CCN
Local
Unoccupied
Local
Remote
Remote
Remote
Unoccupied
Remote
CCN
CCN
CCN
Unoccupied
CCN
Disabled
No
Local
Occupied
Disabled
No
Local
Occupied
Disabled
No
Remote
Occupied
Disabled
No
CCN
Local
Occupied
Disabled
No
Local
Remote
Occupied
Disabled
No
Remote
CCN
Occupied
Disabled
No
CCN
23
UNIT
STATUS
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On
On
Table 19 — Programming Holiday Schedules with
Touch Pilot Display
LINE
NO. VALUE
Holiday Start Month
1
7
Start Day
Config\HOLIDAY\HOLDY_01 2
4
Duration (days)
3
1
Holiday Start Month
1
12
Start Day
Config\HOLIDAY\HOLDY_02 2
25
Duration (days)
3
2
DISPLAY NAME
PATH
Timed Override — With the Touch Pilot display only, each
time schedule can be overridden to keep the chiller in an Occupied mode (Timed Override Hours) for 1, 2, 3 or 4 hours on a
one-time basis. To configure this option for the Touch Pilot display, see Table 20.
Table 20 — Configuring Timed Override
Fig. 18 — Chiller Schedule Screen
DISPLAY NAME
Timed Override
Config\OCCDEFCS\
Hours
OCC1P01S or OCC1P02S
NOTE: This schedule was designed to illustrate the programming of the schedule function and is not intended as a
recommended schedule for chiller operation.
If the chiller is to be controlled to a single set point, use
Schedule 1 (OCCPC01S). This will start and stop the machine.
During the unoccupied times, the chiller will be off. If the chiller is to be controlled to 2 set points, occupied and unoccupied,
use Schedule 2 (OCCPC02S). This will cause the chiller to
control to an occupied set point and an unoccupied set point.
The machine will be able to provide cooling at any time.
To configure this option on the Touch Pilot™ display see
Table 18.
PATH
Period 1 DOW (MTWTFSSH)
Occupied from
Occupied to
Period 2 DOW (MTWTFSSH)
Occupied from
Occupied to
Config\
Period 3 DOW (MTWTFSSH)
OCCDEFCS\
Occupied from
OCC1P01S
Occupied to
or OCC1P02S
Period 4 DOW (MTWTFSSH)
Occupied from
Occupied to
Period 5 DOW (MTWTFSSH)
Occupied from
Occupied to
LINE
NO.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
LINE
NO.
VALUE
1
Range: 0 to 4
Default: 0
If configured for a timed override, the override can be cancelled by changing the Timed Override Hours to 0.
CCN Global Time Schedule — A CCN Global Schedule can
be utilized with the chiller controls. The schedule number can
be set anywhere from 65 to 99 to configure operation under a
CCN global schedule. The 30XA chillers can be configured to
follow a CCN Global Time Schedule broadcast by another system element. ComfortVIEW™ Network Manager’s Configure
and Modify commands or the Service Tool’s Modify/Names
function must be used to change the number of the Occupancy
Equipment Part Table Name (OCC1P01E) to the Global
Schedule Number. The Schedule Number can be set from 65 to
99 (OCC1P65E to OCC1P99E).
The Occupancy Supervisory Part table name (OCC1P01S)
number must be changed to configure the unit to broadcast a
Global Time Schedule. The Schedule Number can be set from
65 to 99 (OCC1P65S to OCC1P99S). When OCC1PxxS is set
to a value greater than 64, an occupancy flag is broadcast over
the CCN every time it transitions from occupied to unoccupied
or vice-versa. By configuring their appropriate Time Schedule
decisions to the same number, other devices on the network can
follow this same schedule.
CCN Mode — To allow machine control by CCN commands,
press the Start/Stop button on the Touch Pilot™ display. The
Equipment Start screen will be displayed. Select CCN Mode.
The unit will be controlled by a CCN command to the CCN
Chiller Start/Stop variable. An external CCN device, such as
Chillervisor, controls the On/Off state of the machine. When
controlled by a Chillervisor, it is recommended that the Auto
Start When SM Lost configuration be set to Yes. In the event
of a loss of communication with the network, the machine will
start and be controlled locally.
Careful evaluation of chilled water plant control should be
reviewed. In the event local control is established, be sure that
all pumps, valves, and other devices are capable of operating
properly. The control will ignore the position of Enable/Off/
Remote Contact switch. The Run Status variable will indicate
the current status of the machine — OFF, RUNNING, DELAY,
or READY. The Control Type variable will change to CCN.
The Operating Type variable will change to CCN.
For dual chiller control applications, the slave chiller must
be enabled using the CCN Mode button.
Remote Mode — To allow machine to start and stop via a
remote contact closure, press the Start/Stop button on the
Touch Pilot display. The Equipment Start screen will be
Table 18 — Configuring the Schedule with
Touch Pilot Display
DISPLAY NAME
PATH
VALUE
10000000
00:00
03:00
11000000
07:00
18:00
00100000
07:00
21:30
00011000
07:00
17:00
00000100
07:00
12:00
Holiday Schedule — For the Touch Pilot display, the control
allows up to 16 holiday periods. All holidays are entered with
numerical values. To configure, first change the month (Holiday Start Month), then the day (Holiday Start Day), then the
duration (Holiday Duration) of the holiday period in days. If a
holiday in included in one of the Occupied Time Periods of the
schedule, the machine will follow that operating condition for
the holiday. In the following examples, the holidays July 4 and
December 25-26 are programmed for Holiday 1 and Holiday 2,
respectively. To configure these holidays with the Touch Pilot
display, see Table 19. To configure Holidays with the Navigator display, check the H (holiday) schedule on the Schedule
screen and program in the desired occupied times. See Fig. 18.
24
displayed. Select Remote Mode. The unit will be controlled by
the Enable/Off/Remote Contact switch. Switching the Enable/
Off/Remote Contact switch to the Enable or Remote Contact position (external contacts closed) will force the unit into
an occupied state. In this mode, all CCN network force commands, except the Emergency Stop Command will be ignored.
The Run Status variable will indicate the current status of the
machine (OFF, RUNNING, DELAY, or READY), depending
on the position of the Remote/Off/Enable Switch closure. The
Chiller Occupied? variable will change to YES. The Control
Type variable will change to Remote. The Operating Type
variable will change to Remote.
Master Mode — To activate Dual Chiller Control, each machine must be individually configured for Dual Chiller Control.
To operate the machines in Dual Chiller Mode, one machine
must be designated as the master unit and one machine as the
slave unit. On the master unit, press the Start/Stop button on the
Touch Pilot display. The Equipment Start screen will be displayed. Select Master Mode. Failure to start the Master unit in
this manner will cause both machines to operate in local mode.
The Master Unit Control can be done locally, remotely or
through CCN commands per the master/slave configuration
(Master Control Type). The control will ignore the position of
Enable/Off/Remote Contact switch if the Master Control
Type is configured for Local Control or CCN Control. The
Run Status variable, Chiller Occupied? variable, and Control Type variable will change based on the Master Control
Type configured above and the Machine On/Off Control defined above. The Operating Type variable will change to
Master.
To Turn Machine Off — To turn the machine off, press the
Start/Stop button on the Touch Pilot display. See Fig. 19. The
machine will shut down. While the unit is in Local Off, it will
remain shut down and ignore all CCN commands as well as
the position of Enable/Off/Remote Contact switch. The Run
Status variable, indicating the current status of the machine,
will change to OFF. The Chiller Occupied? variable will
change to NO. The Control Type variable will indicate
Local. The Operating Type variable will change to L-OFF
(Local Off).
NAVIGATOR™ DISPLAY MACHINE CONTROL —
Machine On/Off control with the Navigator display is determined by the configuration of the Operating Type Control
(OPER). Options to control the machine locally via a switch,
from a local Time Schedule, or via a Carrier Comfort Network® command are offered. See Table 21.
Switch Control — In the Switch Control operating type, the
Enable/Off/Remote Contact switch controls the machine locally. All models are factory configured with Operating Type
Control (OPER) set to SWITCH CTRL (Switch Control).
With SWITCH CTRL, switching the Enable/Off/Remote
Contact switch to the Enable or Remote Contact position (external contacts closed) will put the chiller in an occupied state.
The Unit Run Status (STAT) will indicate the current status of
the machine and will change from OFF to RUNNING or
DELAY. The unit Occupied Status (OCC) will change from
NO to YES. The Status Unit Control Type (CTRL) will change
from LOCAL OFF when the switch is Off to LOCAL ON
when in the Enable position or in the Remote Contact position
with external contacts closed.
ITEM
ITEM EXPANSION
PATH
Operating Control
Operating
OPER
Type
ModesSLCTOPER
VALUE
SWITCH
CTRL
Time Schedule — With Time Schedule Operating Type control, the machine operates under a local schedule programmed
by the user as long as the Enable/Off/Remote Contact switch is
in the Enable or Remote Contact position (external contacts
closed). To operate under this Operating Type Control (OPER)
must be set to TIME SCHED (Time Schedule).
Fig. 19 — Equipment Stop Screen
Table 21 — Navigator Start/Stop Control
CONTROL
ACTIVE
CCN CHILLER EMERGENCY
REMOTE
REMOTE/OFF/ENABLE REMOTE ON/OFF
UNIT
METHOD OPERATING
TIME SCHEDULE 1 START/STOP
STOP
ALARM LOCKOUT STATUS
SWITCH
SWITCH
(OPER)
TYPE
(CHIL_S_S)
(EMSTOP)
SWITCH
All
Local Off
Switch
Control
Local On
Time
Schedule
Local
Schedule
CCN
Control
CCN
Off
—
—
—
—
—
Remote
—
—
—
Enable
Remote
Enable
Remote
—
Remote
Remote
Enable
Enable
Open
—
—
—
—
Closed
—
Closed
—
Closed
Closed
—
—
—
—
—
—
—
—
Occupied
Occupied
Unoccupied
—
—
—
—
—
—
—
—
—
—
—
—
—
Enable
Disable
Enable
Disable
—
Enable
—
—
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
—
—
Yes
—
—
—
—
—
—
—
—
—
—
25
—
—
—
—
Closed
—
—
—
—
—
—
—
—
—
Off
Off
Off
Off
Off
On
On
On
On
Off
On
Off
On
Off
Two Internal Time Schedules are available and must be
field programmed. Time Schedule 1 (SCH1) is used for single
set point On-Off control. Time Schedule 2 (SCH2) is used for
dual set point On-Off and Occupied-Unoccupied set point control. The control will use the operating schedules as defined under the Time Clock mode in the Navigator display module.
ITEM
ITEM EXPANSION
PATH
Operating Control
Operating
OPER Type
ModesSLCTOPER
Table 22 — Configuring Schedules with
Navigator™ Display
ITEM
OCC.1
UNO.1
MON.1
TUE.1
WED.1
THU.1
FRI.1
SAT.1
SUN.1
HOL.1
OCC.2
UNO.2
MON.2
TUE.2
WED.2
THU.2
FRI.2
SAT.2
SUN.2
HOL.2
OCC.3
UNO.3
MON.3
TUE.3
WED.3
THU.3
FRI.3
SAT.3
SUN.3
HOL.3
OCC.4
UNO.4
MON.4
TUE.4
WED.4
THU.4
FRI.4
SAT.4
SUN.4
HOL.4
OCC.5
UNO.5
MON.5
TUE.5
WED.5
THU.5
FRI.5
SAT.5
SUN.5
HOL.5
VALUE
TIME
SCHED
The schedules consist of 8 user-configurable occupied time
periods. The control supports time schedules for local control,
remote control, and ice building. These time periods can be
flagged to be in effect or not in effect on each day of the week.
The day begins at 00.00 and ends at 24.00. The machine is in
unoccupied mode unless a scheduled time period is in effect. If
an occupied period is to extend past midnight, the occupied
period must end at 24:00 hours (midnight) and a new occupied
period must be programmed to begin at 00:00 hours.
In the following example, a early morning pulldown time
period is scheduled for Monday morning from 12:00 AM to
3:00 AM. The occupied period starts at 7:00 AM, Monday
through Saturday. The occupied time ends at 6:00 PM on Monday and Tuesday, 9:30 PM on Wednesday, 5:00 PM on Thursday and Friday, and 12:00 PM on Saturday.
NOTE: This schedule was designed to illustrate the programming of the schedule function and is not intended as a recommended schedule for chiller operation.
If the chiller is to be controlled to a single set point, use
Schedule 1 (SCH1). This type of schedule will start and stop
the machine only. During the unoccupied times, the chiller will
be off. If the chiller is to be controlled to 2 set points, occupied
and unoccupied, use Schedule 2 (SCH2). This will cause the
chiller to control to an occupied set point and an unoccupied set
point. The machine will be able to provide cooling at any time.
To configure this option while using the Navigator™ display, see Table 22.
Holiday Schedule — The unit control allows up to 16 holiday
periods. All holidays are entered with numerical values. First
enter the month (MON.x), then the day (DAY.x), then the
duration (DUR.x) of the holiday period in days. If a holiday in
included in one of the Occupied Time Periods of the schedule,
the machine will follow that operating condition for the
holiday. In the following examples, the holidays July 4 and
December 25-26 are programmed for Holiday 1 and Holiday 2
respectively.
To configure this option for the Navigator display, see
Table 23.
CCN Global Time Schedule — A CCN global schedule can
be used if desired. The schedule number can be set anywhere
from 65 to 99 for operation under a CCN global schedule. The
30XA chillers can be configured to follow a CCN Global
Time Schedule broadcast by another system element. The
ComfortVIEW™ Network Manager’s Configure and Modify
commands or the Service Tool’s Modify/Names function must
be used to change the number of the Occupancy Equipment
Part Table Name (OCC1P01E) to the Global Schedule Number. The Schedule Number can be set from 65 to 99
(OCC1P65E to OCC1P99E).
ITEM EXPANSION
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
PATH
Time
ClockSCH1PER.1
or Time
ClockSCH2PER.1
Time
ClockSCH1PER.2
or Time
ClockSCH2PER.2
Time
ClockSCH1PER.3
or Time
ClockSCH2PER.3
Time
ClockSCH1PER.4
or Time
ClockSCH2PER.4
Time
ClockSCH1PER.5
or Time
ClockSCH2PER.5
VALUE
00:00
03:00
Yes
No
No
No
No
No
No
No
07:00
18:00
Yes
Yes
No
No
No
No
No
No
07:00
21:30
No
No
Yes
No
No
No
No
No
07:00
17:00
No
No
No
Yes
Yes
No
No
No
07:00
12:00
No
No
No
No
No
Yes
No
No
Table 23 — Configuring Holiday Schedules
for Navigator Display
ITEM
MON.1
DAY.1
DUR.1
MON.2
DAY.2
DUR.2
26
ITEM EXPANSION
PATH
VALUE
Holiday Start Month
7
Time
Holiday Start Day
4
ClockHOLIHOL.1
Holiday Duration in Day
1
Holiday Start Month
12
Time
Holiday Start Day
25
ClockHOLIHOL.2
Holiday Duration in Day
2
To configure this option for the Navigator™ display:
The Occupancy Supervisory Part table name (OCC1P01S)
number must be changed to configure the unit to broadcast a
Global Time Schedule. The Schedule Number can be set from
65 to 99 (OCC1P65S to OCC1P99S). When OCC1PxxS is set
to a value greater than 64, an occupancy flag is broadcast over
the CCN every time it transitions from occupied to unoccupied
or vice-versa. By configuring their appropriate Time Schedule
decisions to the same number, other devices on the network can
follow this same schedule. The Enable/Off/Remote Contact
must be in the Enable position or the Remote Contact position
with the contacts closed for the unit to operate. The Unit Run
Status (STAT) will indicate the current status of the machine
(OFF, RUNNING, STOPPING or DELAY), depending on the
schedule. The unit Occupied status (OCC) will indicate the
current occupied schedule according to the schedule, either NO
or YES. The Status Unit Control Type (CTRL) will be LOCAL
OFF when the switch is Off. The Status Unit Control Type will
be CCN when the Enable/Off/Remote Contact switch input is
On.
CCN Control — With CCN Operating Type control, the machine operates under CCN control as long as the Enable/Off/
Remote Contact Switch is in the Enable or Remote Contact
position (external contacts closed.) To operate under this
Operating Control, OPER must be set to CCN CONTROL. An
external CCN device, such as Chillervisor, controls the On/Off
state of the machine. When controlled by a Chillervisor, it is
recommended that the Auto Start When SM Lost (AU.SM) be
set to Yes.
Careful evaluation of Chilled Water Plant control should be
reviewed. In the event Local Control is established, be sure that
all pumps, valves, and other devices are capable of operating
properly. In the event of a loss of communication with the network, the machine will start and be controlled locally. The
CCN device forces the variable CHIL_S_S to control the chiller. The Unit Run Status (STAT) will indicate the current status
of the machine (OFF, RUNNING, STOPPING or DELAY),
depending on the CCN command. The unit Occupied status
(OCC) will indicate the current occupied state according to the
CCN command and will be displayed as either NO or YES.
The Status Unit Control Type (CTRL) will be LOCAL OFF
when the Enable/Off/Remote Contact switch is Off. The Status
Unit Control Type will be CCN when the Enable/Off/Remote
Contact switch input is Closed and the CHIL_S_S variable is
Stop or Start.
For Dual Chiller Control applications, the Slave Chiller
must be enabled using the CCN CONTROL option.
ITEM ITEM EXPANSION
PATH
VALUE
EWTO Entering Water
ConfigurationSERV No = Leaving
Water Control
Control
Yes = Entering
Water Control
Cooling Set Point Selection — Several options for
controlling the Leaving Chilled Water Set Point are offered and
are configured by the Cooling Set Point Select (Setpoint Select, SP.SE) variable. In addition to the Cooling Set Point Select, Ice Mode Enable discussed later in this book, and Heat
Cool Select (Heat/Cool Select, HC.SE) variables also have a
role in determining the set point of the machine. All units are
shipped from the factory with the Heat Cool Select set to 0.
All default set points are based on Leaving Water Control
(Entering Fluid Control, EWTO) set to No. Values must be
confirmed for the individual set points. Limits for the set points
are listed in the configurations noted below.
To configure these options for the Touch Pilot display, see
Table 24A. To configure these options for the Navigator display, see Table 24B.
Table 24A — Cooling Set Point Selection
with Touch Pilot Display
Service\
SERVICE1
VALUE
5
No = Leaving Water Control
Yes = Entering Water Control
3
Cooling Ice Setpoint
Setpoint
4
Range: 14 to 70 F
(–10.0 to 21.1 C)
Default: 44 F (6.6 C)
Range: 14 to 70 F
(–10.0 to 21.1 C)
Default: 44 F (6.6 C)
Range: -20 to 32 F
(–28.9 to 0 C)
Default: 44 F (6.6 C)
PATH
In all cases, there are limits on what values are allowed for
each set point. These values depend on the Cooler Fluid Type
and the Brine Freeze Set point, discussed later. See Table 25.
Table 25 — Configuration Set Point Limits
default for the chilled water fluid set point is controlling to the
leaving water temperature. An option to configure the machine
for entering water control is available. The control operation
remains the same except the control point is focused on the
entering water temperature, rather than the leaving water temperature when configured.
To configure this option for the Touch Pilot™ display:
Entering Fluid
Control
Setpoint
VALUE
VALUE
Range: 14 to 70 F
CSP.1 Cooling Setpoint 1 SetpointsCOOL (–10.0 to 21.1 C)
Default: 44 F (6.6 C)
Range: 14 to 70 F
CSP.2 Cooling Setpoint 2 SetpointsCOOL (–10.0 to 21.1 C)
Default: 44 F (6.6 C)
Range: -20 to 32 F
CSP.3 Ice Setpoint
SetpointsCOOL (–28.9 to 0 C)
Default: 44 F (6.6 C)
Fluid Set Point Control Location — The factory
LINE
NO.
Cooling Setpoint 2
ITEM ITEM EXPANSION
ITEM EXPANSION
PATH
VALUE
Operating Control Operating
CCN
OPER Type
ModesSLCTOPER CONTROL
Auto
Start
when
YES
AU.SM
ConfigurationSERV
SM Lost
PATH
Setpoint
PATH
Table 24B — Cooling Set Point Selection
with Navigator Display
ITEM
DISPLAY NAME
Cooling Setpoint 1
LINE
NO.
2
DISPLAY NAME
SET POINT LIMITS
Minimum *
Maximum
COOLER FLUID TYPE
(COOLER FLUID TYPE, FLUD)
1, Water
2, Brine
38 F (3.3 C)
14 F (–10.0 C)
60 F (15.5 C)
*The minimum set point for Medium Temperature Brine applications
is related to the Brine Freeze Point. The set point is limited to be no
less than the Brine Freeze Point +5° F (2.8° C).
The Setpoint Select configuration can be set to five different
control options: Set Point Occupancy, Set Point 1, Set Point 2,
4-20 mA Input, and Dual Switch.
SET POINT OCCUPANCY — Set Point Occupancy is the
default configuration for the Setpoint Select variable. When
Setpoint Select (Setpoint Select, SP.SE) is configured to 0
(Setpoint Occ), the unit’s active set point is based on Cooling
27
The following equation is used to control the set point. See
Fig. 20.
Fahrenheit Set Point = 10 + 70(mA – 4)/16 (deg F)
Celsius Set Point = –12.2 + 38.9(mA – 4)/16 (deg C)
To configure this option while using a Touch Pilot display:
Set Point 1 (Cooling Setpoint 1, CSP.1) during the occupied
period while operating under Time Schedule 1 (SCH1). If the
Time Schedule 2 (SCH2) is in use, the unit’s active set point is
based on Cooling Set Point 1 (Cooling Setpoint 1, CSP.1) during the occupied period and Cooling Set Point 2 (Cooling Setpoint 2, CSP.2) during the unoccupied period. See Tables 26
and 27.
To configure this option while using a Touch Pilot display:
LINE
VALUE
NO.
Setpoint select StatusGENUNIT 25 0 (Setpoint Occupied)
DISPLAY NAME
PATH
Setpoint select
StatusGENUNIT
DISPLAY NAME
VALUE
1 (Set Point 1)
Setpoint select
To change this value, a Control Point Force must be applied.
When configured correctly, Setpoint Control will indicate
Setp 1.
To configure this option with the Navigator™ display:
ITEM
Setpoint select
StatusGENUNIT
LINE
NO.
25
StatusGENUNIT
ITEM EXPANSION
SP.SE Setpoint Select
Set Point 2 — When Set Point Select (Setpoint Select, SP.SE)
is configured to 2 (Setpoint 2), the unit’s active set point is
based on Cooling Set Point 2 (Cooling Setpoint 2, CSP.2).
To configure this option with the Touch Pilot™ display:
PATH
PATH
LINE
NO.
VALUE
25
4 (Dual
Setpoint Switch)
To change this value, a Control Point Force must be applied.
When configured correctly, Setpoint Control will indicate
Setp Sw.
To configure this option while using a Navigator display:
ITEM ITEM EXPANSION
PATH
VALUE
SP.SE Setpoint Select
Operating ModesSLCT Setpoint 1
DISPLAY NAME
StatusGENUNIT
Dual Switch — When Set Point Select (Setpoint Select,
SP.SE) is configured to 4 (Dual Setp Sw), the unit’s active set
point is based on Cooling Set Point 1 (Cooling Setpoint 1,
CSP.1) when the Dual Set Point switch contact is open and
Cooling Set Point 2 (Cooling Setpoint 2, CSP.2) when it is
closed.
To configure this option while using a Touch Pilot display:
Set Point 1 — When Set Point Select (Setpoint Select, SP.SE)
is configured to 1 (Setpoint 1), the unit’s active set point is
based on Cooling Set Point 1 (Cooling Setpoint 1, CSP.1).
To configure this option with the Touch Pilot display:
LINE
NO.
25
Setpoint select
LINE
VALUE
NO.
25
3 (4-20 mA Input)
ITEM ITEM EXPANSION
PATH
VALUE
SP.SE Setpoint Select
Operating ModesSLCT 4-20 mA Setp
ITEM ITEM EXPANSION
PATH
VALUE
SP.SE Setpoint Select
Operating ModesSLCT Setpoint Occ
PATH
PATH
To change this value, a Control Point Force must be applied.
When configured correctly, Setpoint Control will indicate 420 mA.
To configure this option while using a Navigator display:
To change this value, a Control Point Force must be applied.
When configured correctly, Setpoint Control (Setpoint
Control, SP.SE) will indicate Auto.
To configure this option while using a Navigator display:
DISPLAY NAME
DISPLAY NAME
PATH
Operating ModesSLCT
VALUE
Dual
Setp Sw
Chilled Water Fluid Type Selection — The chilled
water fluid must be configured. The fluid type must be configured to obtain the proper leaving water set point control range
and freeze protection. The Cooler Fluid Type (Cooler Fluid
Type, FLUD) can be set to water or brine.
FRESH WATER — Configure the unit for Cooler Fluid Type
(Cooler Fluid Type, FLUD) to water for units without brine or
glycol installed in the chilled water loop. The factory default
fluid type is fresh water. Use this option for fresh water systems. This will allow for a water temperature set point of 38 to
60 F (3.3 to 15.5 C). With water as the selection, the Freeze
Point is fixed at 34 F (1.1 C).
To configure this option with the Touch Pilot display:
VALUE
2 (Set Point 2)
To change this value, a Control Point Force must be applied.
When configured correctly, Setpoint Control (Status
GENUNIT) will indicate Setp 2.
To configure this option with the Navigator display:
ITEM ITEM EXPANSION
PATH
VALUE
SP.SE Setpoint Select
Operating ModesSLCT Setpoint 2
DISPLAY
LINE
PATH
NAME
NO. VALUE
Cooler
1 1 = Water
Main MenuServiceSERVICE1
Fluid Type
4 to 20 mA Input — When Set Point Select (Setpoint Select,
SP.SE) is configured to 3 (4-20 mA Setp), the unit’s active set
point is based on an field supplied, external 4 to 20 mA signal
input to the Energy Management Module (EMM). Care should
be taken when interfacing with other manufacturer’s control
systems, due to power supply differences of full wave bridge
versus half wave rectification. The two different power supplies cannot be mixed. ComfortLink™ controls use half wave
rectification. A signal isolation device should be utilized if a
full wave bridge signal generating device is used.
To configure this option with the Navigator display:
ITEM
FLUD
28
ITEM EXPANSION
Cooler Fluid Type
PATH
ConfigurationSERV
VALUE
Water
90
80
70
Max LWT
Set Point
60
50
Min LWT, Cooler Fluid Type = 1, FLUD=Water
40
30
20
Min LWT, Cooler Fluid Type = 1, FLUD=Brine
10
0
0
2
4
6
8
10
12
14
16
18
20
a30-4476
mA Signal
Fig. 20 — 4 to 20 mA Set Point Control
Table 26 — Cooling Set Point Selection Touch Pilot™ Parameters
SET POINT
CONFIGURATION
(Setpoint Select)
ICE MODE
ENABLE
(ice_cnfg)
NO
0
(Auto)
YES
1 (Setp 1)
2 (Setp 2)
3 (4-20 mA)
—
—
—
NO
4 (Setp Sw)
YES
DUAL SET
POINT INPUT
(SETP_SW)
—
—
—
—
—
—
—
—
Open
Closed
Open
Closed
Closed
ICE DONE INPUT
(ICE_SW)
TIME
SCHEDULE 2
ACTIVE
SET POINT
—
—
Open
Closed
—
—
—
—
—
—
—
Open
Closed
Occupied
Unoccupied
Unoccupied
Unoccupied
Occupied
—
—
—
—
—
—
—
—
Cooling Setpoint 1
Cooling Setpoint 2
Cooling Ice Setpoint
Cooling Setpoint 2
Cooling Setpoint 1
Cooling Setpoint 1
Cooling Setpoint 2
4 to 20 mA Input
Cooling Setpoint 1
Cooling Setpoint 2
Cooling Setpoint 1
Cooling Ice Setpoint
Cooling Setpoint 2
Table 27 — Cooling Set Point Selection Navigator™ Parameters
PARAMETER STATUS
Control Method
(OPER)
Heat/Cool
Select (HC.SE)
LOCAL
COOL
CCN
COOL
Setpoint
Select (SP.SE)
Ice Mode
Enable (ICE.M)
Ice Done
(ICE.D)
Dual Setpoint
Switch (DUAL)
Setpoint Occ
Setpoint Occ
Setpoint Occ
Setpoint 1
Setpoint 2
4-20mA Setp
—
—
—
Dual Setp Sw
—
—
—
—
Enable
—
—
—
Enable
Enable
—
—
—
—
—
—
Open
—
—
—
Open
Closed
—
—
—
—
—
—
—
—
—
—
Closed
Closed
Open
Closed
—
—
29
Setpoint
Occupied
(SP.OC)
Occupied
Unoccupied
Unoccupied
—
—
—
—
—
—
—
Occupied
Unoccupied
ACTIVE
SET POINT
CSP.1
CSP.2
CSP.3
CSP.1
CSP.2
4_20mA
CSP.3
CSP.2
CSP.1
CSP.2
CSP.1
CSP.2
When Cooler Pumps Sequence is set to 0 (No Pump), closure of both the chilled water flow switch (CWFS) and the
chilled water pump interlock contact (connected across TB-5
terminals 1 and 2) are required for the unit to start mechanical
cooling.
To configure this option with the Touch Pilot™ display:
BRINE OR GLYCOL OPERATION — Configure the unit
for Cooler Fluid Type (Cooler Fluid Type, FLUD) to brine for
brine or glycol chilled water loops. This option will allow for a
set point temperature range of 14 to 60 F (–10.0 to 15.5 C).
Before configuring this selection, confirm that a suitable antifreeze has been added and is at a sufficient concentration to
protect the loop. Additionally, the Brine Freeze Set Point
(Brine Freeze Setpoint, LOSP) must be set for proper freeze
protection operation. Set the Brine Freeze Set Point to the burst
protection provided by the glycol concentration. This value
will be Freeze Point for the fluid.
To configure this option with the Touch Pilot display:
DISPLAY NAME
Cooler Pumps
Sequence
PATH
LINE
NO.
VALUE
Main
MenuConfigUSER
8
0 (No Pump
Control)
To configure this option with the Navigator™ display:
DISPLAY
LINE
PATH
VALUE
NAME
NO.
Cooler Fluid Main Menu
Type
ServiceSERVICE1 1 2 = Brine
Brine Freeze Main Menu
Dependent on
Setpoint
ServiceSERVICE1 3 fluid concentration
ITEM
PUMP
ITEM EXPANSION
PATH
Cooler Pumps
Configuration
OPTN
Sequence
VALUE
No Pump
SINGLE PUMP CONTROL — For units with the single
pump hydronic package, the factory default setting for Cooler
Pumps Sequence (Cooler Pumps Sequence, PUMP) is 1
(1 Pump Only). This control algorithm may be used to control
an external pump, as long as the same controls are applied as
noted below.
When the Cooler Pumps Sequence configuration is set to 1
Pump Only, closure of both the chilled water flow switch
(CWFS) and the chilled water pump interlock contact (connected across TB-5 terminals 1 and 2) are required for the unit
to start mechanical cooling. Additionally, the normally open
auxiliary contacts for Pump 1 contactor must be connected to
the violet and pink wires located in the harness from the MBBJ5C-CH18 connector. The wires in the harness are marked
“PMP1-13” and “PMP1-14”. See the field wiring diagram in
the 30XA Installation Instructions.
Three additional parameters are configurable for pump control with single pump control. Periodic pump start and check
flow if pump is off parameters can customize the pump operation for the application. Another parameter, to stop the pump in
standby mode is not supported.
The control system has the ability to periodically start the
pumps to maintain the bearing lubrication and seal integrity. If
Periodic Pump Start (Pump Sticking Protection, PM.PS) is
set to YES and the unit is off at 2:00 PM, the pump will be
started once each day for 2 seconds. The default for this option
is NO.
Another configuration to check the status of the chilled
water flow switch can be selected. When configured, if Flow
Checked if Pump Off (Flow Checked if C Pump Off, P.LOC)
is set to YES, the control will monitor the chilled water flow
switch status and will alarm if the pump is commanded off and
the chilled water flow switch is closed. This can provide the
user with information of a faulty cooler pump contactor or a
failed chilled water flow switch. This parameter should be set
to NO for series flow machines. The factory default for this
item is YES.
To configure this option with the Touch Pilot display:
To configure this option with the Navigator display:
ITEM ITEM EXPANSION
PATH
VALUE
FLUD Cooler Fluid Type ConfigurationSERV Brine
Dependent on
Brine Freeze
LOSP Setpoint
ConfigurationSERV fluid concentration
Cooler Pump Control — It is required for flooded
cooler units that cooler pump control be utilized on all chillers
unless the chilled water pump runs continuously or the chilled
water system contains a suitable antifreeze solution. The 30XA
units can be configured for single external pump control as
standard. Control of dual external pumps requires installation
of the external pump control accessory package (Part No.
00EFN900003200A).
Cooler Pumps Sequence (Cooler Pumps Sequence,
PUMP) is the variable that must be confirmed in the field.
Proper configuration of the cooler pump control is required to
provide reliable chiller operation. Pump control can be accomplished for both on-board and external pumps. For external
pump control, control connections to the pump contactor and a
feedback circuit from the contactor must be supplied. The
Cooler Pumps Sequence configuration can be set to 5 different
control settings: No Pump Control, Single Pump Control, Dual
Pump Control, Pump 1 Manual, and Pump 2 Manual.
When the Cooler Pumps Sequence is configured, the cooler
pump output will be energized when the chiller enters an “ON”
mode. The cooler pump output is also energized when certain
alarms are generated. The cooler pump output should be used
as an override to the external pump control if cooler pump control is not utilized. The cooler pump output is energized if a
P.01 Water Exchanger Freeze Protection alarm is generated,
which provides additional freeze protection if the system is not
protected with a suitable antifreeze solution.
A chilled water pump interlock contact PMP-I is connected
across TB5 terminals 1-2, as an alternative to the standard
jumper. This interlock is an optional field-installed device
which would provide extra protection in the event of the flow
switch failing closed. It may be used regardless of whether or
not pump control is enabled. However, this interlock should
NOT be confused with the pump contactor feedback auxiliary
contacts which MUST be wired to MBB channel 18 at connector J5C if the pump control feature is enabled (with or without
the optional on-board hydronic package).
NO PUMP CONTROL — The factory default setting for
Cooler Pumps Sequence (Cooler Pumps Sequence, PUMP)
is 0 (No Pump), for units without the factory-installed hydronic
package.
DISPLAY NAME
30
PATH
LINE
NO.
Cooler Pumps
Sequence
Main
MenuConfigUSER
8
Pump Sticking
Protection
Main
MenuConfigUSER
15
Flow Checked
if C Pump Off
Main
MenuConfigUSER
17
VALUE
1 (Single
Pump Control)
Default = No
No = Disabled
Yes = Enabled
Default = Yes
No = Disabled
Yes = Enabled
To configure these options with the Touch Pilot™ display:
To configure this option with the Navigator display:
ITEM ITEM EXPANSION
PATH
VALUE
PUMP Cooler Pumps
ConfigurationOPTN 1 Pump Only
Sequence
Default = No
Periodic Pump
PM.PS Start
ConfigurationOPTN No = Disabled
Yes = Enabled
Default = Yes
Flow Checked
P.LOC if Pmp Off
ConfigurationOPTN No = Disabled
Yes = Enabled
LINE
NO.
VALUE
Main Menu
ConfigUSER
8
2 (2 Pumps Automatic)
3 (Pump 1 Manual)
4 (Pump 2 Manual)
Pump Auto
Main Menu
Rotation Delay ConfigUSER
14
Pump Sticking Main Menu
Protection
ConfigUSER
15
Flow Checked
if C Pump Off
17
DISPLAY NAME
Cooler Pumps
Sequence
DUAL PUMP AND MANUAL CONTROL — For units with
the dual pump hydronic package, the factory default setting for
Cooler Pumps Sequence (Cooler Pumps Sequence, PUMP)
is 2 (2 Pumps Auto). This control algorithm may be used to
control two external pumps, as long as the same controls are
applied as noted below. For dual pump hydronic option units,
three control options exist. The control will start the pumps and
automatically alternate the operation of the pumps to even the
wear of the pumps based on the hours configured under Pump
Auto Rotation Delay (Pump Auto Rotation Delay, ROT.P). If
the difference between the operating hours of the 2 pumps exceeds the Pump Auto Rotation Delay the lead pump will
change. If a flow failure is detected, the other pump will attempt to start.
Two manual control options also exist. When the Cooler
Pumps Sequence (Cooler Pumps Sequence, PUMP) is set to
3 (PMP 1 Manual), Cooler Pump 1 will always operate. When
the Cooler Pumps Sequence (Cooler Pumps Sequence,
PUMP) is set to 4 (PMP 2 Manual), Cooler Pump 2 will always operate.
If the Cooler Pumps Sequence configuration is set to 2
(2 Pumps Auto), 3 (PMP 1 Manual), or 4 (PMP 2 Manual),
closure of both the chilled water flow switch (CWFS) and the
chilled water pump interlock contact (connected across TB-5
terminals 1 and 2) are required for the unit to start mechanical
cooling. Additionally, the normally open auxiliary contacts for
Pump 1 and Pump 2 contactors (wired in parallel) must be connected to the violet and pink wires located in the harness from
the MBB-J5C-CH18 connector. The wires in the harness are
marked “PMP1-13” and “PMP1-14”. See the field wiring diagram in the 30XA Installation Instructions.
Three additional parameters are configurable for pump control with single pump control. The Periodic Pump Start (Pump
Sticking Protection, PM.PS) and Flow Checked if Pump Off
(Flow Checked if C Pump Off, P.LOC) parameters can customize the pump operation for the application. Another parameter, that is used to stop the pump in standby mode, is not
supported.
The control system has the ability to periodically start the
pumps to maintain the bearing lubrication and seal integrity. If
Periodic Pump Start (Pump Sticking Protection, PM.PS) is
set to YES and if the unit is off at 2:00 PM, a pump will be
started once each day for 2 seconds. If the unit has 2 pumps,
Pump 1 will be started on even days (such as day 2, 4, or 6 of
the month); Pump 2 will be started on odd days (such as day 1,
3 or 5 of the month). The default for this option is NO.
A configuration to check the status of the chilled water flow
switch can be selected. When Flow Checked if Pump Off
(Flow Checked if C Pump Off, P.LOC) is configured to YES,
the control will monitor the chilled water flow switch status
and will alarm if the pump is commanded off and the chilled
water flow switch is closed. This can provide the user with
information of a faulty cooler pump contactor or a failed
chilled water flow switch. This parameter should be set to NO
for series flow machines. The factory default for this item is
YES.
PATH
Main Menu
ConfigUSER
Default = 48 hours
Default = No
No = Disabled
Yes = Enabled
Default = Yes
No = Disabled
Yes = Enabled
To configure these options with the Navigator™ display:
ITEM ITEM EXPANSION
PATH
Cooler Pumps
PUMP
Sequence
ConfigurationOPTN
ROT.P Pump Rotation
Delay
ConfigurationOPTN
Periodic Pump
PM.PS Start
ConfigurationOPTN
Flow Checked
P.LOC if Pmp Off
ConfigurationOPTN
VALUE
2 Pumps Auto
PMP1 Manual
PMP2 Manual
Default =
48 hours
Default = No
No = Disabled
Yes = Enabled
Default = Yes
No = Disabled
Yes = Enabled
Machine Start Delay — An option to delay the start of
the machine is also available. This parameter is useful in keeping multiple machines from starting at the same time in case of
a power failure. The parameter has a factory default of
1 minute. This parameter also has a role in the timing for a
chilled water flow switch alarm.
To configure this option with the Touch Pilot display:
DISPLAY NAME
Unit Off to
On Delay
PATH
Main Menu
ConfigUSER
LINE
NO.
VALUE
6
Default = 1 Minute
To configure this option with the Navigator display:
ITEM
ITEM EXPANSION
DELY
Minutes Off Time
PATH
ConfigurationOPTN
VALUE
Default =
1 Minute
Circuit/Compressor Staging and Loading —
The AquaForce® 30XA chillers employ one compressor per
circuit. As a result, circuit and compressor staging are the
same. The control has several control option parameters to load
the compressors. The circuit/compressor start can be configured as well as the loading of each circuit/compressor.
CIRCUIT/COMPRESSOR STAGING — The control can be
configured to decide which circuit/compressor starts first, by
configuring Lead/Lag Circuit Select (Staged Loading
Sequence, LLCS). Four options for this variable are allowed:
Automatic Lead-Lag, Circuit A Leads, Circuit B Leads, or
Circuit C Leads (30XA400-500 only). The factory default is
Automatic Lead-Lag.
The automatic lead-lag function determines which circuit/
compressor starts. When enabled, the control will determine
which circuit/compressor starts to even the wear of the compressor. The compressor wear factor (combination of starts and
run hours) is used to determine which compressor starts.
Compressor Wear Factor = (Compressor Starts) + 0.1 (Compressor Run Hours)
The circuit/compressor with the lowest compressor wear
factor is the circuit that starts first.
If starting a particular circuit/compressor first is desired, that
can also be configured with the same variable.
31
To configure this option with the Navigator display:
To configure this option with the Touch Pilot display:
DISPLAY NAME
LINE
NO.
PATH
VALUE
ITEM
0 (Automatic Lead-lag)
1 (Circuit A Leads)
2 (Circuit B Leads)
3 (Circuit C Leads)
Default = 0
(Automatic Lead-lag)
Circuit Loading Main Menu
Sequence
ConfigUSER 1
ITEM EXPANSION
Lead/Lag
LLCS Circuit Select
PATH
Configuration
OPTN
available for the control of two units installed in series or parallel supplying chilled fluid on a common loop. One chiller must
be configured as the master chiller, the other as the slave chiller. An additional leaving fluid temperature thermistor (Dual
Chiller LWT) must be installed in the common chilled water
piping as described in the Installation Instructions for both the
master and slave chillers. See the Field Wiring section in the
30XA Installation Instructions for Dual Chiller LWT sensor
control wiring.
The control algorithm relies on several parameters that must
be field configured for operation. Both chillers must be on the
same Carrier Comfort Network® bus with different addresses.
On both chillers, Master/Slave Select (Master/Slave Select,
MSSL) must be enabled. The water piping arrangement, Chillers in Series (Chiller in Series, SERI), must be configured.
The master chiller must be programmed with the Slave Chiller
Address (Slave Address, SLVA). Additional optional programming parameters may be configured to meet application
requirements.
Lead/Lag Balance Select (Lead Lag Select, LLBL) determines which chiller is the lead machine. The options are Always Lead, Lag if Fail, and Runtime Select. Under Runtime
Select control, the lead chiller will change based on the time increment selected in the Lead/Lag Balance Delta configuration
(Lead/Lag Balance Data, LLBD). If the run hour difference
between the master and the slave remains less than the Lead/
Lag Balance Delta, the chiller designated as the lead will
remain the lead chiller. The Lead/Lag changeover between the
master and the slave chiller due to hour balance will occur during chiller operating odd days, such as day 1, day 3, and day 5
of the month, at 12:00 a.m. If a lead chiller is not designated,
the master chiller will always be designated the lead chiller.
The dual chiller control algorithm has the ability to delay
the start of the lag chiller in two ways. The Lead Pulldown
Time parameter (Lead Pulldown Type, LPUL) is a one-time
time delay initiated after starting the lead chiller, before checking whether to start an additional chiller. This time delay gives
the lead chiller a chance to remove the heat that the chilled
water loop picked up while being inactive during an unoccupied period. The second time delay, Lead/Lag Delay (Lag
Start Timer, LLDY) is a time delay imposed between the last
stage of the lead chiller and the start of the lag chiller. This prevents enabling the lag chiller until the lead/lag delay timer has
expired.
A quicker start of the lag chiller can be accomplished by
configuring the Start if Error Higher parameter (Start if Error
Higher, LL.ER). If the difference between the common leaving water temperature and the set point is greater than the configured value, then the lag chiller will start.
A minimum on time for the lag chiller can be programmed
with the Lag Minimum Running Time configuration (Lag
Minimum Running Time, LAG.M). This parameter causes
the control to run the lag chiller for the programmed minimum
on time. The Lag Unit Pump Select (Lag Unit Pump Control,
LAGP) can be configured such that the pump can be on or off
while the chiller is off. This parameter is only active in Parallel
Chiller Operation.
CIRCUIT/COMPRESSOR LOADING — The control can
be configured to stage the circuit/compressors. The Loading
Sequence Select (Circuit Loading Sequence, LOAD) setting
determines how the control will perform loading. The configuration can be set to Equal or Staged.
Equal Loading — With Equal loading, the circuit which starts
first will maintain the minimum stage of capacity with the slide
valve fully unloaded. When additional capacity is required, the
next circuit with the lowest compressor wear factor is started
with its slide valve at minimum position. As additional capacity is required, the slide valve for a circuit will be adjusted in
approximately 5% increments to match capacity requirements.
The control will alternate between circuits to maintain the same
percentage of capacity on each circuit. See Fig. 21.
Staged Loading — If staged loading is selected, the circuit
which starts first will gradually load its slide valve to match
capacity requirements until the circuit is fully loaded. Once the
circuit is fully loaded and additional capacity is required, the
control will start an additional circuit fully unloaded. The control will gradually unload the circuit which was fully loaded to
match capacity requirements. See Fig. 21.
To configure this option with the Touch Pilot™ display:
PATH
LINE
NO.
VALUE
Staged Loading
Sequence
Main
MenuConfigUSER
4
Default = No
No (Equal)
Yes (Staged)
To configure this option with the Navigator™ display:
ITEM ITEM EXPANSION
VALUE
Default = Equal
Loading Sequence
LOAD Select
ConfigurationOPTN Equal
Staged
PATH
Minimum Load Control — Minimum Load Control
can be a factory-installed option or a field-installed accessory.
If installed, and its operation is desired, the Minimum Load
Control must be enabled. Once enabled, the valve will be operational only during the first stage of cooling.
To configure this option with the Touch Pilot display:
DISPLAY NAME
Hot Gas
Bypass Select
PATH
Main
MenuService
FACTORY
LINE
NO.
14
VALUE
Dual Chiller Control — The dual chiller routine is
VALUE
Range: Automatic,
Cir A Leads,
Cir B Leads,
Cir C Leads
Default – Automatic
DISPLAY NAME
PATH
No = No Minimum
Hot Gas
Load Control
ConfigurationUNIT
HGBP
Bypass Select
Yes = Minimum Load
Control Installed
To configure this option with the Navigator display:
ITEM
ITEM
EXPANSION
VALUE
Default = No
No (No Minimum
Load Control)
Yes (Minimum Load
Control Installed)
32
Lead Compressor Loading
Lag Compressor Loading
Lead Compressor Unloading
Lag Compressor Unloading
Lead compressor can fall anywhere in this area
when load between 40%~65%
100
Compressor Capacity (%)
80
UNLOADING
LOADING
60
40
20
Lag compressor can fall anywhere in this area
when load between 40%~65%
0
100
0
0
Load (%)
a30-4466
Equal Circuit Loading
Compressor Loading Unloading (Staged circuit loading)
Lead Compressor Loading
Lag Compressor Loading
100
Lead Compressor Unloading
Lag Compressor Unloading
Compressor Capacity (%)
80
60
40
20
0
0
100
0
Load (%)
Staged Circuit Loading
a30-4477
Fig. 21 — Compressor Loading and Unloading
For units with a Touch Pilot display, two additional steps
DUAL CHILLER CONTROL FOR PARALLEL APPLImust be completed to start the machine. On the master chiller,
CATIONS — To configure the master chiller for parallel
the Master Control Type must be configured for the start conapplications using the Touch Pilot display, see Table 28. To
trol defined in the Machine Control configuration. To start the
configure the master chiller for parallel applications using the
machines, the master chiller must be started with the Start/Stop
Navigator display, see Table 29.
button and Master Mode selected. The slave chiller must be
To configure the slave chiller for parallel applications using
started with the CCN Mode selected.
the Touch Pilot display, see Table 30. To configure the slave
Each application, Parallel and Series, are described sepachiller for parallel applications using the Navigator display, see
rately below.
Table 31. A power cycle is required for the values to take
effect.
33
Table 28 — Dual Master Chiller Control Parameters for Parallel Applications with Touch Pilot™ Display
DISPLAY NAME
PATH
LINE NO.
Master/Slave Select
Main MenuConfigMST_SLV
3
Master Control Type
Main MenuConfigMST_SLV
7
Slave Address
Main MenuConfigMST_SLV
11
Lead Lag Select
Main MenuConfigMST_SLV
12
Lead/Lag Balance Delta
Main MenuConfigMST_SLV
16
Lag Start Timer
Main MenuConfigMST_SLV
17
Lead Pulldown Time
Main MenuConfigMST_SLV
18
Start If Error Higher
Main MenuConfigMST_SLV
19
Lag Minimum Running Time
Main MenuConfigMST_SLV
20
Lag Unit Pump Control
Main MenuConfigMST_SLV
21
Chiller In Series
Main MenuConfigMST_SLV
22
VALUE
1 (Master)
Default: 0 (Disable)
1=Local Control
2=Remote Control
3=CCN Control
Default: 1
Configure for proper control type.
Must be set to the Slave Chiller’s address.
The master and slave chiller must have
different addresses and be on the same
Bus Number
Default: 2
0 (Master Always Leads)
1 (Lag Once Failed Only)
2 (Lead/Lag Runtime Select)
Default: 0 (Master Always Leads)
Range: 40 to 400 hours
Default: 168 hours
Range: 2 to 30 minutes
Default: 10 minutes
Range: 0 to 60 minutes
Default: 0 minutes
Range: 3.0 to 18 F (1.7 to 10.0 C)
Default: 4.0 F (2.2 C)
Range: 0 to 150 minutes
Default: 0 minutes
0 (Stop If Unit Stops)
1 (Run If Unit Stops)
Default: 0 (Stop If Unit Stops)
Default: No
Value: No
NOTE: If pump control is configured to OFF, then LAG UNIT PUMP
SELECT = 1. If pump control is set to any other value, then LAG
UNIT PUMP SELECT = 0. This configuration must be set consistently for both master and slave chillers.
Table 29 — Dual Master Chiller Control Parameters for Parallel Applications with Navigator™ Display
ITEM
ITEM EXPANSION
PATH
MSSL
Master/Slave Select
ConfigurationRSET
SLVA
Slave Address
ConfigurationRSET
LLBL
Master Lead Lag Select
ConfigurationRSET
LLBD
Lead/Lag Balance Delta
ConfigurationRSET
LLDY
Lag Start Delay
ConfigurationRSET
LL.ER
Start If Error Higher
ConfigurationRSET
LAG.M
Lag Unit Pump Select
ConfigurationRSET
LPUL
Lead Pulldown Time
ConfigurationRSET
SERI
Chillers in Series
ConfigurationRSET
OPER
Operating Control Type
Operating ModesSLCT
NOTE: If pump control is configured to OFF, then LAG UNIT PUMP
SELECT = 1. If pump control is set to any other value, then LAG
UNIT PUMP SELECT = 0. This configuration must be set consistently for both master and slave chillers.
34
VALUE
Master
Default: Disable
Must be set to the Slave Chiller’s address.
The master and slave chiller must have
different addresses and be on the same
Bus Number
Default: 2
Range: Always Lead, Lag if Fail, Runtime Sel
Default: Always Lead
Range: 40 to 400 hours
Default: 168 hours
Range: 2 to 30 minutes
Default: 10 minutes
Range: 3.0 to 18 F (1.7 to 10.0 C)
Default: 4.0 F (2.2 C)
Range: Off If U Stp, On If U Stop
Default: Off If U Stp
Range: 0 to 60 minutes
Default: 0 minutes
No
Default: No
Set to desired control
Table 30 — Dual Slave Chiller Control Parameters for Parallel Applications with Touch Pilot™ Display
DISPLAY NAME
PATH
LINE NO.
Master/Slave Select
Main MenuConfigMST_SLV
3
Master Control Type
Main MenuConfigMST_SLV
7
Slave Address
Main MenuConfigMST_SLV
11
Lead Lag Select
Main MenuConfigMST_SLV
12
Lead/Lag Balance Delta
Main MenuConfigMST_SLV
16
Lag Start Timer
Main MenuConfigMST_SLV
17
Lead Pulldown Time
Main MenuConfigMST_SLV
18
Start If Error Higher
Main MenuConfigMST_SLV
19
Lag Minimum Running Time
Main MenuConfigMST_SLV
20
Lag Unit Pump Control
Main MenuConfigMST_SLV
21
Chiller In Series
Main MenuConfigMST_SLV
22
VALUE
2 (Slave)
Default: 0 (Disable)
1 (Local Control)
2 (Remote Control)
3 (CCN Control)
Default: 1
Configure for proper control type.
Must be set to the Slave Chiller’s address.
The master and slave chiller must have
different addresses and be on the same
Bus Number
Default: 2
0 (Master Always Leads)
1 (Lag Once Failed Only)
2 (Lead/Lag Runtime Select)
Default: 0 (Master Always Leads)
Range: 40 to 400 hours
Default: 168 hours
Range: 2 to 30 minutes
Default: 10 minutes
Range: 0 to 60 minutes
Default: 0 minutes
Range: 3.0 to 18 F (1.7 to 10.0 C)
Default: 4.0 F (2.2 C)
Range: 0 to 150 minutes
Default: 0 minutes
0 (Stop If Unit Stops)
1 (Run If Unit Stops)
Default: 0 (Stop If Unit Stops)
No
Default: No
NOTE: If pump control is configured to OFF, then LAG UNIT PUMP
SELECT = 1. If pump control is set to any other value, then LAG
UNIT PUMP SELECT = 0. This configuration must be set consistently for both master and slave chillers.
Table 31 — Dual Slave Chiller Control Parameters for Parallel Applications with Navigator™ Display
ITEM
ITEM EXPANSION
PATH
MSSL
Master/Slave Select
ConfigurationRSET
SLVA
Slave Address
ConfigurationRSET
LLBL
Master Lead Lag Select
ConfigurationRSET
LLBD
Lead/Lag Balance Delta
ConfigurationRSET
LLDY
Lag Start Delay
ConfigurationRSET
LL.ER
Start If Error Higher
ConfigurationRSET
LAG.M
Lag Unit Pump Select
ConfigurationRSET
LPUL
Lead Pulldown Time
ConfigurationRSET
SERI
Chillers in Series
ConfigurationRSET
OPER
Operating Control Type
Operating ModesSLCT
NOTE: If pump control is configured to OFF, then LAG UNIT PUMP
SELECT = 1. If pump control is set to any other value, then LAG
UNIT PUMP SELECT = 0. This configuration must be set consistently for both master and slave chillers.
35
VALUE
Slave
Default: Disable
Must be set to the Slave Chiller’s address.
The master and slave chiller must have
different addresses and be on the same
Bus Number
Default: 2
Range: Always Lead, Lag if Fail, Runtime Sel
Default: Always Lead
Range: 40 to 400 hours
Default: 168 hours
Range: 2 to 30 minutes
Default: 10 minutes
Range: 3.0 to 18 F (1.7 to 10.0 C)
Default: 4.0 F (2.2 C)
Range: Off If U Stp, On If U Stop
Default: Off If U Stp
Range: 0 to 60 minutes
Default: 0 minutes
No,
Default: No
CCN Control
DUAL CHILLER CONTROL FOR SERIES APPLICATIONS — To configure the master chiller for series applications using the Touch Pilot™ display, see Table 32. To
configure the master chiller for series applications using the
Navigator™ display, see Table 33.
To configure the slave chiller for series applications using
the Touch Pilot™ display, see Table 34. To configure the slave
chiller for series applications using the Navigator™ display,
see Table 35. A power cycle is required for the values to take
effect.
DUAL CHILLER PUMP CONTROL FOR PARALLEL
CHILLER APPLICATIONS — It is recommended that a
dedicated pump be used for each unit. The chiller must start
and stop its own water pump located on its own piping. If
pumps are not dedicated for each chiller, chiller isolation
valves are required and each chiller must open and close its
own isolation valve.
Table 32 — Dual Master Chiller Control Parameters for Series Applications with Touch Pilot™ Display
DISPLAY NAME
PATH
LINE NO.
Master/Slave Select
Main MenuConfigMST_SLV
3
Master Control Type
Main MenuConfigMST_SLV
7
Slave Address
Main MenuConfigMST_SLV
11
Lead Lag Select
Main MenuConfigMST_SLV
12
Lead/Lag Balance Delta
Main MenuConfigMST_SLV
16
Lag Start Timer
Main MenuConfigMST_SLV
17
Lead Pulldown Time
Main MenuConfigMST_SLV
18
Start If Error Higher
Main MenuConfigMST_SLV
19
Lag Minimum Running Time
Main MenuConfigMST_SLV
20
Lag Unit Pump Control
Main MenuConfigMST_SLV
21
Chiller In Series
Main MenuConfigMST_SLV
22
NOTE: If pump control is configured to OFF, then LAG UNIT PUMP
SELECT = 1. If pump control is set to any other value, then LAG
VALUE
1 (Master)
Default: 0 (Disable)
1 (Local Control)
2 (Remote Control)
3 (CCN Control)
Default: 1 (Local Control)
Value: Configure for proper control type.
Must be set to the Slave Chiller’s address.
The master and slave chiller must have
different addresses and be on the same
Bus Number
Default: 2
0 (Master Always Leads)
1 (Lag Once Failed Only)
2 (Lead/Lag Runtime Select)
Default: 0 (Master Always Leads)
Range: 40 to 400 hours
Default: 168 hours
Range: 2 to 30 minutes
Default: 10 minutes
Range: 0 to 60 minutes
Default: 0 minutes
Range: 3.0 to 18 F (1.7 to 10.0 C)
Default: 4.0 F (2.2 C)
Range: 0 to 150 minutes
Default: 0 minutes
0 (Stop If Unit Stops)
1 (Run If Unit Stops)
Default: 0 (Stop If Unit Stops)
Yes
Default: No
UNIT PUMP SELECT = 0. This configuration must be set consistently for both master and slave chillers.
Table 33 — Dual Master Chiller Control Parameters for Series Applications with Navigator™ Display
ITEM
ITEM EXPANSION
PATH
MSSL
Master/Slave Select
ConfigurationRSET
SLVA
Slave Address
ConfigurationRSET
LLBL
Master Lead Lag Select
ConfigurationRSET
LLBD
Lead/Lag Balance Delta
ConfigurationRSET
LLDY
Lag Start Delay
ConfigurationRSET
LL.ER
Start If Error Higher
ConfigurationRSET
LAG.M
Lag Unit Pump Select
ConfigurationRSET
LPUL
Lead Pulldown Time
ConfigurationRSET
SERI
Chillers in Series
ConfigurationRSET
OPER
Operating Control Type
Operating ModesSLCT
NOTE: If pump control is configured to OFF, then LAG UNIT PUMP
SELECT = 1. If pump control is set to any other value, then LAG
UNIT PUMP SELECT = 0. This configuration must be set consistently for both master and slave chillers.
36
VALUE
Master
Default: Disable
Must be set to the Slave Chiller’s address.
The master and slave chiller must have
different addresses and be on the same
Bus Number
Default: 2
Range: Always Lead, Lag if Fail, Runtime Sel
Default: Always Lead
Range: 40 to 400 hours
Default: 168 hours
Range: 2 to 30 minutes
Default: 10 minutes
Range: 3.0 to 18 F (1.7 to 10.0 C)
Default: 4.0 F (2.2 C)
Range: Off If U Stp, On If U Stop
Default: Off If U Stp
Range: 0 to 60 minutes
Default: 0 minutes
YES
Default: NO
Set to desired value
Table 34 — Dual Slave Chiller Control Parameters for Series Applications with Touch Pilot Display
DISPLAY NAME
PATH
LINE NO.
Master/Slave Select
Main MenuConfigMST_SLV
3
Master Control Type
Main MenuConfigMST_SLV
7
Slave Address
Main MenuConfigMST_SLV
11
Lead Lag Select
Main MenuConfigMST_SLV
12
Lead/Lag Balance Delta
Main MenuConfigMST_SLV
16
Lag Start Timer
Main MenuConfigMST_SLV
17
Lead Pulldown Time
Main MenuConfigMST_SLV
18
Start If Error Higher
Main MenuConfigMST_SLV
19
Lag Minimum Running Time
Main MenuConfigMST_SLV
20
Lag Unit Pump Control
Main MenuConfigMST_SLV
21
Chiller In Series
Main MenuConfigMST_SLV
22
NOTE: If pump control is configured to OFF, then LAG UNIT PUMP
SELECT = 1. If pump control is set to any other value, then LAG
VALUE
2 (Slave)
Default: 0 (Disable)
1 (Local Control)
2 (Remote Control)
3 (CCN Control)
Default: 1 (Local Control)
Value: Configure for proper control type.
Must be set to the Slave Chiller’s address.
The master and slave chiller must have
different addresses and be on the same
Bus Number
Default: 2
0 (Master Always Leads)
1 (Lag Once Failed Only)
2 (Lead/Lag Runtime Select)
Default: 0 (Master Always Leads)
Range: 40 to 400 hours
Default: 168 hours
Range: 2 to 30 minutes
Default: 10 minutes
Range: 0 to 60 minutes
Default: 0 minutes
Range: 3.0 to 18 F (1.7 to 10.0 C)
Default: 4.0 F (2.2 C)
Range: 0 to 150 minutes
Default: 0 minutes
0 (Stop If Unit Stops)
1 (Run If Unit Stops)
Default: 0 (Stop If Unit Stops)
Yes
Default: No
UNIT PUMP SELECT = 0. This configuration must be set consistently for both master and slave chillers.
Table 35 — Dual Slave Chiller Control Parameters for Series Applications with Navigator Display
ITEM
ITEM EXPANSION
PATH
MSSL
Master/Slave Select
ConfigurationRSET
SLVA
Slave Address
ConfigurationRSET
LLBL
Master Lead Lag Select
ConfigurationRSET
LLBD
Lead/Lag Balance Delta
ConfigurationRSET
LLDY
Lag Start Delay
ConfigurationRSET
LL.ER
Start If Error Higher
ConfigurationRSET
LAG.M
Lag Unit Pump Select
ConfigurationRSET
LPUL
Lead Pulldown Time
ConfigurationRSET
SERI
Chillers in Series
ConfigurationRSET
OPER
Operating Control Type
Operating ModesSLCT
VALUE
Slave
Default: Disable
Must be set to the Slave Chiller’s address.
The master and slave chiller must have
different addresses and be on the same
Bus Number
Default: 2
Range: Always Lead, Lag if Fail,
Runtime Sel
Default: Always Lead
Range: 40 to 400 hours
Default: 168 hours
Range: 2 to 30 minutes
Default: 10 minutes
Range: 3.0 to 18 F (1.7 to 10.0 C)
Default: 4.0 F (2.2 C)
Range: Off If U Stp, On If U Stop
Default: Off If U Stp
Range: 0 to 60 minutes
Default: 0 minutes
YES
Default: NO
CCN Control
NOTE: If pump control is configured to OFF, then LAG UNIT PUMP
SELECT = 1. If pump control is set to any other value, then LAG
UNIT PUMP SELECT = 0. This configuration must be set consistently for both master and slave chillers.
DUAL CHILLER PUMP CONTROL FOR SERIES
CHILLER APPLICATIONS — Pump control for series chiller applications is controlled by the master chiller only. The
control of the slave chiller is directed through commands emitted by the master chiller. The slave chiller has no action in
master/slave operations. The slave chiller only verifies that
CCN communication with the master chiller is present. See the
Dual Chiller Sequence of Operation section on page 68.
Night Time/Low Noise Operation — The ComfortLink™ controls have the ability to lower the sound level of
the machine by reducing the number of fans that are running,
provided that the conditions are acceptable. Reducing the number of running fans also limits the capacity. Three parameters
must be configured for this operation. A start and end time for
the mode of operation is required and an optional capacity limit
set point must also be configured.
37
Under normal operation, the chiller will maintain a constant
entering or leaving fluid temperature, based on the configuration, approximately equal to the chilled fluid set point. As the
cooler load varies, the cooler fluid temperature difference will
change in proportion to the load. For example, if the chiller was
selected for a Entering to Leaving Water Temperature difference of 10 F (5.5 C) at full load, at 50% load the temperature
difference would be 5 F (2.2 C). See Fig. 22. Because the
change in temperature through the cooler is a measure of the
building load, the temperature difference reset is the average
building load. Usually the chiller size and fluid temperature set
point are selected based on a full load condition. At part load,
the fluid temperature set point may be lower than required. If
the fluid temperature were allowed to increase at part load, the
efficiency of the machine would increase. The chiller can also
be set for return water temperature control. See Fig. 23.
Other indirect means of estimating building load and controlling temperature reset are also available and are discussed
below.
To verify that reset is functioning correctly, subtract the Setpoint Select (Current Setpoint, SETP) from the Control Point
(Control Point, CTPT) to determine the degrees reset.
RETURN WATER RESET — The control system is capable
of performing fluid temperature reset based on cooler fluid
temperature difference. Because the change in temperature
through the cooler is a measure of the building load, the temperature difference reset is, in effect, an average building load
reset method.
Return Water Temperature Reset allows for the chilled
water temperature set point to be reset upward as a function of
the fluid temperature difference (building load).
NOTE: Return Water Temperature Reset should not be used
with variable cooler flow rate systems.
To use Return Water Temperature Reset, four variables
must be configured. Cooling Reset Type (Cooling Reset
Select, CRST) must be enabled. The variable Delta T No Reset
Temp (Delta T No Reset Value, CRT1) should be set to the
cooler temperature difference (T) where no chilled water temperature reset should occur. The variable Delta T Full Reset
Temp (Delta T Full Reset Value, CRT2) should be set to the
cooler temperature difference where the maximum chilled
water temperature reset should occur. The variable Degrees
Cool Reset (Cooling Reset Deg. Value, DGRC) should be set
to the maximum amount of reset desired.
To configure this option with the Touch Pilot display:
If the Start and End Time remain at the factory default
(0:00), then the unit is not programmed for Night Time/Low
Noise Operation.
To configure this option with the Touch Pilot™ display:
LINE
VALUE
NO.
Start Hour
Main MenuConfigUser 39 Default: 00:00
End Hour
Main MenuConfigUser 40 Default: 00:00
Capacity Limit Main MenuConfigUser 41 Default: 100%
DISPLAY NAME
PATH
To configure this option with the Navigator™ display:
ITEM
ITEM EXPANSION
PATH
VALUE
Night Low Noise
LS.ST Start
ConfigurationOPTN Default: 00:00
LS.ND Night Low Noise
ConfigurationOPTN Default: 00:00
End
Low Noise Capacity
ConfigurationOPTN Default: 100%
LS.LT
Lim
Ramp Loading — Ramp Loading limits the rate of
change of the leaving fluid temperature. If the unit is in a Cooling mode and configured for Ramp Loading Select (Ramp
Loading Select, RL.S), the control makes two comparisons
before deciding to increase capacity. First, the control calculates the temperature difference between the control point and
leaving fluid temperature. If the difference is greater than 4° F
(2.2° C) and the rate of change (°F or °C per minute) is more
than the configured Cool Ramp Loading rate (Cooling Ramp
Loading, CRMP), then the control does not allow any increase
of capacity.
To configure this option with the Touch Pilot display:
DISPLAY NAME
PATH
LINE
NO.
Ramp Loading
Select
Main Menu
ConfigUSER
5
Cooling Ramp
Loading
Main Menu
Setpoint
14
VALUE
Yes
Range: 0.2 to 2.0 °F
(0.1 to 1.1 °C)
Default: 1.0 °F (0.5 °C)
To configure this option with the Navigator display:
ITEM
PATH
VALUE
EXPANSION
Ramp Load
RL.S Select
ConfigurationOPTN Yes
Range: 0.2 to 2.0 °F
Cool Ramp
SetpointsCOOL
(0.1 to 1.1 °C)
CRMP
Loading
Default: 1.0 °F (0.5 °C)
ITEM
DISPLAY
NAME
Temperature Reset — Temperature reset is a value
added to the basic leaving fluid temperature set point and the
resulting sum of these values is the new control point. When a
non-zero temperature reset is applied, the chiller controls to the
new control point, not the set point. The type of temperature reset is configured with the Cooling Reset Type (Cooling Reset
Select, CRST) variable. Four types of temperature reset are
available: Return Water Reset, Outside Air Temperature Reset,
Space Temperature Reset, and 4-20 mA Temperature Reset.
PATH
Cooling Reset Main
Select
MenuConfigUSER
Delta T No
Reset Temp
Delta T Full
Reset Temp
Cooling Reset
Deg. Value
38
Main
MenuSetpointSETPOINT
Main
MenuSetpointSETPOINT
Main
MenuSetpointSETPOINT
LINE
NO.
19
7
8
13
VALUE
Default =0
(No Reset)
2 (Delta T)
Default =
0 F (0 C)
Default =
0 F (0 C)
Default =
0 F (0 C)
56
54
Fluid Temperature (deg F)
52
EWT
50
Design
Rise
(typical)
48
46
LWT
44
42
40
0
10
20
30
40
50
60
70
80
90
100
a30-4066
% Load
Fig. 22 — Leaving Chilled Water Temperature Control
56
EWT
54
Fluid Temperature (deg F)
52
50
Design
Rise
(typical)
LWT
48
46
44
42
40
0
10
20
30
40
50
60
70
80
90
100
a30-4478
% Load
Fig. 23 — Return Water Temperature Control Load Profile
39
To use Space Temperature Reset, four variables must be
configured. Cooling Reset Type (Cooling Reset Select, CRST)
must be enabled. The space temperature at which no temperature reset is required, Space T No Reset Temp (Space T No
Reset Value, CRS1) must be set. The space temperature at
which full temperature reset is required, Space T Full Reset
Temp (Space T Full Reset Value, CRS2) must be set. Finally,
the amount of temperature reset desired, Degrees Cool Reset
(Cooling Reset Deg. Value, DRGC), must be set.
To configure this option with the Touch Pilot display:
To configure this option with the Navigator™ display:
ITEM
CRST
ITEM EXPANSION
Cooling Reset
Type
Delta T No
Reset Temp
Delta T Full
CRT2
Reset Temp
Degrees Cool
DGRC Reset
CRT1
PATH
VALUE
Default =
ConfigurationRSET No Reset
Delta T Temp
Default =
SetpointsCOOL
0 F (0 C)
Default =
SetpointsCOOL
0 F (0 C)
Default =
SetpointsCOOL
0 F (0 C)
DISPLAY NAME
In the example in Fig. 24 using Return Water Temperature
Reset, the chilled water temperature will be reset by 5° F
(2.8° C) when the Fluid Temperature Difference is 2° F
(1.1° C) and 0° F (0° C) reset when the Temperature Difference
is 10° F.
OUTSIDE AIR TEMPERATURE RESET — The control system is also capable of temperature reset based on outdoor-air
temperature (OAT).
To use Outdoor Air Temperature Reset, four variables must
be configured. Cooling Reset Type (Cooling Reset Select,
CRST) must be enabled. The outside temperature at which no
temperature reset is required, OAT No Reset Temp (OAT No
Reset Value, CRO1) must be set. The outside temperature at
which full temperature reset is required, OAT Full Reset Temp
(OAT Full Reset Value, CRO2) must be set. Finally, the
amount of temperature reset desired, Degrees Cool Reset
(Cooling Reset Deg. Value, DRGC) must be set.
To configure this option with the Touch Pilot™ display:
DISPLAY NAME
LINE
NO.
PATH
Cooling Reset
Select
Main
MenuConfigUSER
OAT No Reset
Value
OAT Full Reset
Value
Cooling Reset
Deg. Value
Main
MenuSetpointSETPOINT
Main
MenuSetpointSETPOINT
Main
MenuSetpointSETPOINT
19
5
6
13
CRST
ITEM EXPANSION
Cooling Reset
Type
CRO1 OAT No Reset
Temp
OAT Full Reset
CRO2
Temp
Degrees Cool
DGRC Reset
Cooling Reset
Select
ConfigUSER
Main Menu
Space T No
Reset Value
Space T Full
Reset Value
Cooling Reset
Deg. Value
Main Menu
SetpointSETPOINT
Main Menu
SetpointSETPOINT
Main Menu
SetpointSETPOINT
19
11
12
13
VALUE
Default =0
(No Reset)
4 (Space Temp)
Default =
14 F (–10 C)
Default =
14 F (–10 C)
Default =
0 F (0 C)
To configure this option with the Navigator display:
ITEM
CRST
CRS1
CRS2
DGRC
VALUE
Default =0
(No Reset)
1 (OAT)
Default =
14 F (–10 C)
Default =
14 F (–10 C)
Default =
0 F (0 C)
ITEM EXPANSION
PATH
VALUE
Default =
Cooling Reset Type ConfigurationRSET No Reset
Space Temp
Space T No Reset
Default =
Setpoints

COOL
Temp
14 F (–10 C)
Space T Full Reset
Default =
SetpointsCOOL
Temp
14 F (–10 C)
Default =
Degrees Cool Reset SetpointsCOOL
0 F (0 C)
In the space temperature reset example in Fig. 26, 0° F
(0° C) chilled water set point reset at 72 F (22.2 C) space
temperature and 6° F (3.3° C) reset at 68 F (20.0 C) space
temperature.
4-20 mA TEMPERATURE RESET — The control system is
also capable of temperature reset based on an externally powered 4 to 20 mA signal. The Energy Management Module
(EMM) is required for temperature reset using a 4 to 20 mA
signal.
To use 4-20 mA Temperature Reset, four variables must be
configured. Cooling Reset Type (Cooling Reset Select, CRST)
must be enabled. The milliamp signal at which no temperature
reset is required, Current No Reset Value (Current No Reset
Value, CRV1), must be set. The milliamp signal at which full
temperature reset is required, Current Full Reset Value
(Current Full Reset Value, CRV2), must be set. Finally, the
amount of temperature reset desired, Degrees Cool Reset
(Cooling Reset Deg. Value, DRGC), must be set.
To configure this option with the Navigator display:
ITEM
LINE
NO.
PATH
PATH
VALUE
Default =
ConfigurationRSET No Reset
Out Air Temp
Default =
SetpointsCOOL
14 F (–10 C)
Default =
SetpointsCOOL
14 F (–10 C)
Default =
SetpointsCOOL
0 F (0 C)
CAUTION
In the example in Fig. 25, the outdoor air temperature reset
example provides 0° F (0° C) chilled water set point reset at
85 F (29.4 C) outdoor-air temperature and 15° F (8.3° C) reset
at 55 F (12.8 C) outdoor-air temperature.
SPACE TEMPERATURE RESET — The control system is
also capable of temperature reset based on space temperature
(SPT). An accessory sensor must be used for SPT reset
(33ZCT55SPT). The Energy Management Module (EMM) is
also required for temperature reset using space temperature.
Care should be taken when interfacing with other control
systems due to possible power supply differences such as a
full wave bridge versus a half wave rectification. Connection of control devices with different power supplies may
result in permanent damage. The ComfortLink™ controls
incorporate power supplies with half wave rectification. A
signal isolation device should be utilized if the signal generator incorporates a full wave bridge rectifier.
40
6
5
Degrees Reset (deg F)
4
Cooling
Reset
Deg. Value,
DGRC
3
Delta T No Reset Temp,
CRT1
2
Delta T Full Reset Temp,
CRT2
1
0
2
0
6
4
8
10
a30-4479
Entering-Leaving Water Temperature (deg F)
Fig. 24 — Return Water Reset
16
14
Reset Amount (deg F)
12
10
Cooling Reset
Deg. Value,
DGRC
8
6
OAT No Reset Value,
CRO1
OAT Full Reset Value,
CRO2
4
2
0
0
20
40
60
80
Outdoor Temperature
Fig. 25 — OAT Temperature Reset
41
100
120
a30-4480
7
6
Degrees Reset (deg F)
5
4
Cooling Reset
Deg. Value,
DGRC
3
Space T No Reset Value,
CRS1
2
Space T Full Reset Value,
CRS2
1
0
60
65
70
75
Space Temperature (deg F)
80
a30-4481
Fig. 26 — Space Temperature Reset
To configure this option with the Touch Pilot™ display:
DISPLAY NAME
LINE
NO.
PATH
Cooling Reset
Select
ConfigUSER
Main Menu
Current No
Reset Value
Current Full
Reset Value
Cooling Reset
Deg. Value
SetpointSETPOINT
19
Main Menu
Main Menu
SetpointSETPOINT
Main Menu
SetpointSETPOINT
9
10
13
maximum capacity linearly between 100% at a 4 mA input
signal (no reduction) down to the user-configurable level at a
20 mA input signal. The third type uses the CCN Loadshed
module and has the ability to limit the current operating capacity to maximum and further reduce the capacity if required. Demand limit control can be based on a calculated capacity level
or by compressor current level.
NOTE: If using the compressor current level for demand limit,
take into account the other power draws such as the condenserfan motors when determining the limit value desired.
SWITCH CONTROLLED DEMAND LIMIT — The control system is capable of demand limit based on a field-supplied switch for 1-step demand limit or 2 switches for 2-step
demand limit. One-step Demand Limit is standard. The 2-step
switch control of demand limiting requires the Energy Management Module (EMM). Demand Limit steps are controlled
by two relay switch inputs field wired to TB5-5 and TB5-14
for Switch 1 and TB6-14 and TB6-15 for Switch 2.
For demand limit by switch control, closing the first demand limit contact will put the unit on the first demand limit
level, either by capacity or compressor current. The unit will
not exceed the percentage of capacity or compressor current
entered as Demand Limit Switch 1 set point. Closing contacts
on the second demand limit switch prevents the unit from exceeding the demand limit entered as Demand Limit Switch 2
set point. The demand limit percent capacity or compressor
current that is set to the lowest demand takes priority if both demand limit inputs are closed. If the demand limit percentage
does not match unit operation, the unit will limit capacity or
current to the closest step without exceeding the value.
To use Demand Limit, select the type of demand limiting to
use by configuring the Demand Limit Select variable (Demand Limit Type Select, DMDC) to Switch. Configure the
Demand Limit set points based on the type selected.
VALUE
Default =0
(No Reset)
3 (4-20mA
Control)
4.0 mA
Default = 0.0
30.0 mA
Default = 0.0
Default =
0.0 F (0.0 C)
To configure this option with the Navigator™ display:
ITEM ITEM EXPANSION
Cooling Reset
CRST Type
Current No
Reset Temp
Current Full
CRV2 Reset Temp
DGRC Degrees Cool
Reset
CRV1
PATH
VALUE
Default =
ConfigurationRSET No Reset
4-20mA Input
4.0 mA
SetpointsCOOL
Default = 0.0
20.0 mA
SetpointsCOOL
Default = 0.0
5.0 F (2.8 C)
SetpointsCOOL
Default = 0.0
In the example in Fig. 27, at 4 mA no reset takes place and
at 20 mA, 5° F (2.8° C) chilled water set point reset is required.
Demand Limit — Demand limit is a feature that allows
the unit capacity to be limited during periods of peak energy
usage. This allows the owner to keep energy costs down. There
are three types of demand limiting that can be configured. The
first type is through 2-step switch control, which will reduce
the maximum capacity to 2 user configurable percentages. The
second type is by 4 to 20 mA signal input which will reduce the
42
6
5
Degrees Reset (deg F)
4
Cooling Reset
Deg. Value
(DGRC)
3
Current No Reset Value
(CRV1)
2
1
Current Full
Reset Value
(CRV2)
0
0
10
5
15
20
a30-4482
mA Signal
Fig. 27 — 4 to 20 mA Temperature Reset
capacity to 40%. Demand Limit Switch 1 is 60% and Demand
Limit Switch 2 is 40%.
Switch Controlled (Capacity Based) — If using 2-step Demand Limit control, an Energy Management Module must be
installed. One-step Demand Limit control does not require the
Energy Management Module. To configure Demand Limit for
switch control, three parameters for 1-step switch control must
be configured. For 2-step control, four parameters must be
configured. The parameters are: the type of Demand Limit
Selection (Demand Limit Type Select, DMDC), the setting
for Switch Limit Set Point 1 (Switch Limit Setpoint 1, DLS1),
The setting for Switch Limit Set Point 2 (Switch Limit Setpoint 2, DLS2), and Current Limit Select (Current Limit Select, CUR.S). Current Limit Select must be set to NO.
To configure this option with the Touch Pilot™ display:
DISPLAY NAME
PATH
LINE
NO.
VALUE
Demand Limit
Type Select
Switch Limit
Setpoint 1
ConfigUSER
24
1 (Switch Control)
Default = 0 (None)
SetpointsSETPOINT
33
Default = 100%
Switch Limit
Setpoint 2
SetpointsSETPOINT
34
Current Limit
Select
ConfigUSER
30
TOUCH PILOT DISPLAY
Display Name
Value
Demand Limit Type Select
1
Switch Limit Setpoint 1
60%
Switch Limit Setpoint 2
40%
Current Limit Select
No
NAVIGATOR DISPLAY
Item
Value
DMDC
SWITCH
DSL1
60%
DSL2
40%
CUR.S
NO
Switch Controlled (Current Based) — If using 2-step demand limit control, an Energy Management Module must be
installed. One-step demand limit control does not require the
Energy Management Module. Four parameters for 1-step
switch control must be configured. For 2-step control, five
parameters must be configured. The parameters are: the type
of Demand Limit Selection (Demand Limit Type Select,
DMDC), the setting for Switch Limit Set Point 1 (Switch Limit Setpoint 1, DLS1), the setting for Switch Limit Set Point 2
(Switch Limit Setpoint 2, DLS2), the Current Limit Select
(Current Limit Select, CUR.S), and the Compressor Current
limit at 100% signal, (Current Limit at 100%, CUR.F).
To configure this option with the Touch Pilot display:
(Not required
for 1-Step)
Default = 100%
No
Default = No
DISPLAY NAME
To configure this option with the Navigator™ display:
ITEM ITEM EXPANSION
PATH
VALUE
Demand
Limit
SWITCH
DMDC
ConfigurationRSET
Select
Default = NONE
Switch Limit
Default = 100%
DLS1
SetpointsMISC
Setpoint 1
(Not required
for 1-Step)
DLS2 Switch Limit
SetpointsMISC
Setpoint 2
Default = 100%
NO
Current Limit
CUR.S Select
ConfigurationOPTN Default: NO
In the following example, 2-step demand limit based on
capacity is desired with the first switch closure limiting the
capacity to 60%. The second switch closure is to limit the
43
PATH
LINE
NO.
VALUE
Demand Limit
Type Select
ConfigUSER
24
1 (Switch Control)
Default = 0
(None)
Switch Limit
Setpoint 1
SetpointsSETPOINT
33
Default = 100%
Switch Limit
Setpoint 2
SetpointsSETPOINT
34
Current Limit
Select
Current Limit
at 100%
ConfigUSER
30
ConfigUSER
31
(Not required
for 1-Step)
Default = 100%
Yes
Default = No
Default =
2000.0 Amps
20 mA signal is connected to TB6-1 and TB6-2. The demand
limit is a linear interpolation between the two values entered. In
Fig. 28, if the machine receives a 12 mA signal, the machine
controls will limit the capacity to 50%.
EXTERNALLY POWERED (4 to 20 mA) CURRENT
BASED DEMAND LIMIT — The Energy Management
Module is required for 4 to 20 mA demand limit control. An
externally powered 4 to 20 mA signal must be connected to
TB6-1 and TB6-2. To configure demand limit for 4 to 20 mA
control based on compressor current, five parameters must be
configured. The parameters are: the type of Demand Limit
Selection (Demand Limit Type Select, DMDC), the current at
which 100% capacity limit takes place (mA For 100%
Demand Limit, DMMX), the current at which 0% capacity
limit takes place (mA For 0% Demand Limit, DMZE), the
Current Limit Selection (Current Limit Select, CUR.S), and
the Compressor Current limit at 100% signal (Current Limit
at 100%, CUR.F).
To configure this option with the Navigator™ display:
ITEM ITEM EXPANSION
Demand Limit
DMDC
Select
DSL1
Switch Limit
Setpoint 1
DSL2
Switch Limit
Setpoint 2
CUR.S Current Limit
Select
Current Limit
CUR.F
at 100%
PATH
VALUE
SWITCH
ConfigurationRSET Default =
NONE
Default =
SetpointsMISC
100%
(Not required
for 1-Step)
SetpointsMISC
Default =
100%
NO
ConfigurationOPTN
Default: NO
Default =
ConfigurationOPTN
2000
EXTERNALLY POWERED (4 to 20 mA) CAPACITY
BASED DEMAND LIMIT — The Energy Management
Module is required for 4 to 20 mA demand limit control. An
externally powered 4 to 20 mA signal must be connected to
TB6-1 and TB6-2. To configure demand limit for 4 to 20 mA
control based on unit capacity, four parameters must be configured. The parameters are: the type of Demand Limit Selection
(Demand Limit Type Select, DMDC), the current at which
100% capacity limit takes place (mA For 100% Demand
Limit, DMMX), the current at which 0% capacity limit takes
place (mA For 0% Demand Limit, DMZE), and the Current
Limit Selection (Current Limit Select, CUR.S).
CAUTION
Care should be taken when interfacing with other control
systems due to possible power supply differences such as a
full wave bridge versus a half wave rectification. Connection of control devices with different power supplies may
result in permanent damage. ComfortLink controls incorporate power supplies with half wave rectification. A signal isolation device should be utilized if the signal
generator incorporates a full wave bridge rectifier.
CAUTION
Care should be taken when interfacing with other control
systems due to possible power supply differences such as a
full wave bridge versus a half wave rectification. Connection of control devices with different power supplies may
result in permanent damage. ComfortLink™ controls
incorporate power supplies with half wave rectification. A
signal isolation device should be utilized if the signal generator incorporates a full wave bridge rectifier.
To configure this option with the Touch Pilot display:
DISPLAY NAME
Demand Limit
Type Select
mA For 100%
Demand Limit
mA For 0%
Demand Limit
Current Limit
Select
Current Limit
at 100%
To configure this option with the Touch Pilot™ display:
DISPLAY NAME
Demand Limit
Type Select
mA For 100%
Demand Limit
mA For 0%
Demand Limit
Current Limit
Select
LINE
NO.
PATH
ConfigUSER
24
ConfigUSER
28
ConfigUSER
29
ConfigUSER
30
VALUE
2 (4-20mA Control)
Default = 0 (None)
4.0 mA
Default = 0.0 mA
20.0 mA
Default = 10.0 mA
No
Default = No
PATH
ConfigRSET
ConfigRSET
ConfigRSET
ConfigOPTN
LINE
NO.
ConfigUSER
24
ConfigUSER
28
ConfigUSER
29
ConfigUSER
30
ConfigUSER
31
VALUE
2 (4-20mA Control)
Default = 0 (None)
4.0 mA
Default = 0.0 mA
20.0 mA
Default = 10.0 mA
Yes
Default = No
Default = 2000.0 Amps
To configure this option with the Navigator display:
ITEM ITEM EXPANSION
DMDC Demand Limit
Select
mA for 100%
DMMX
Demand Lim
mA for 0%
DMZE Demand Limit
CUR.S Current Limit
Select
Current Limit
CUR.F
at 100%
To configure this option with the Navigator display:
ITEM ITEM EXPANSION
Demand Limit
DMDC
Select
mA for 100%
DMMX Demand Lim
DMZE mA for 0%
Demand Limit
Current Limit
CUR.S
Select
PATH
VALUE
4-20MA INPUT
Default = NONE
4.0 mA
Default = 0.0 mA
20.0 mA
Default = 10.0 mA
NO
Default: NO
PATH
VALUE
ConfigRSET 4-20MA INPUT
Default = NONE
4.0 mA
ConfigRSET
Default = 0.0 mA
20.0 mA
ConfigRSET Default = 10.0 mA
ConfigOPTN YES
Default: NO
ConfigOPTN Default = 2000
In the following example, a 4 mA signal is Demand Limit
for compressor current is 2000 amps and a 20 mA Demand
Limit signal corresponds with a compressor current of 0 amps.
The 4 to 20 mA signal is connected to TB6-1 and TB6-2. The
demand limit is a linear interpolation between the two values
entered. If the machine receives a 12 mA signal, the machine
controls will limit the total compressor current capacity to
1000 amps. See Fig. 29.
In the following example, a 4 mA signal is Demand Limit
100% and a 20 mA Demand Limit signal is 0%. The 4 to
44
100
90
80
% Demand Limit
70
60
mA For 0% Demand Limit,
DMZE
50
40
30
mA For 100% Demand Limit,
DMMX
20
10
0
2
0
4
6
8
10
12
14
16
18
mA Demand Limit Signal
20
a30-4483
Fig. 28 — 4 to 20 mA Demand Limit (Capacity)
2000
1800
1600
Compressor Current
1400
1200
mA For 0% Demand Limit,
DMZE
1000
80 0
60 0
mA Fo r 100% Demand Limit,
DMMX
40 0
20 0
0
0
2
4
6
8
10
12
14
16
mA Signal
Fig. 29 — 4 to 20 mA Demand Limit (Compressor Current)
45
18
20
a30-4484
To configure this option with the Touch Pilot display:
CCN LOADSHED CONTROLLED DEMAND LIMIT —
To configure Demand Limit for CCN Loadshed control, the
unit Operating Type Control must be in CCN control. With the
Touch Pilot™ display, the machine must be started with CCN
Control. For the Navigator™ display, the Operating Control
Type (I/O Button, OPER) must be CCN CONTROL.
The unit must be controlled by a Chillervisor module. The
Chillervisor module can force the demand limit variable and
directly control the capacity of the machine. Additionally, the
unit’s set point will be artificially lowered to force the chiller to
load to the demand limit value.
DISPLAY NAME
Activate
configured to make and store ice. The Energy Management
Module and an Ice Done Switch are required for operation in
the Ice Mode. In this configuration, the machine can operate
with up to three cooling set points: Cooling Set Point 1 (Cooling Setpoint 1, CSP.1) is used during the Occupied period;
Cooling Set Point 2 (Cooling Setpoint 2, CSP.2) is used during the Unoccupied period when the ice build is complete (Ice
Done Switch is closed); and Cooling Ice Set Point (Cooling
Ice Setpoint, CSP.3) is used during the unoccupied period
while ice is building (Ice Done Switch is open).
To configure this option with the Touch Pilot display:
Ice Mode Enable
PATH
ConfigUSER
LINE
NO.
42
ITEM EXPANSION
Ice Mode Enable
PATH
ConfigurationOPTN
VALUE
1
Range = 0 to 2
Default = 2
ConfigBRODEFS
DISPLAY NAME
LINE
NO.
PATH
Activate
ConfigBRODEFS
1
OAT Broadcast
ConfigBRODEFS
3
Bus #
ConfigBRODEFS
4
Element #
ConfigBRODEFS
5
VALUE
VALUE
Range = 0 to 2
Default = 2
Range = 0 to 239
Default = 0
Range = 0 to 239
Default = 0
BROADCAST ACKNOWLEDGER — This configuration
defines if the chiller will be used to acknowledge broadcast
messages on the CCN bus. One broadcast acknowledger is required per bus, including secondary buses created by the use of
a bridge. This variable can only be changed with the Touch Pilot display, ComfortVIEW software, or Network Service Tool.
This variable cannot be changed with the Navigator display.
To configure this option with the Touch Pilot display:
Yes
To configure this option with the Navigator display:
ITEM
ICE.M
LINE
NO.
OAT BROADCAST — To enable the outside air temperature
(OAT) broadcast, the unit broadcasting the temperature must
be configured with its own CCN Bus and CCN Address. Leaving the parameters at the factory default of 0 for the CCN Bus
and CCN Address disables the OAT Broadcast function. Once
configured, the first broadcast of OAT will be within 5 minutes.
This variable can only be changed when using the Touch Pilot
display, ComfortVIEW software, or Network Service Tool.
This variable cannot be changed with the Navigator display.
To configure this option with the Touch Pilot display:
Ice Storage Operation — Chiller operation can be
DISPLAY NAME
PATH
VALUE
ENBL
Broadcast Configuration — The 30XA chiller is ca-
pable of broadcasting outside-air temperature (OAT), time,
date, and holiday status to all elements in the CCN system. In
the stand-alone mode, broadcast must be activated to utilize
holiday schedules and adjust for daylight saving time. If the
chiller is to be connected to a CCN system, determine which
system element is to be the network broadcaster and activate
broadcast in all other system elements. Broadcast is activated
and deactivated in the BRODEFS Table. It is accessible from
Touch Pilot display (ConfigBRODEFS) or through Network Service Tool. It is not accessible through Navigator
display.
Only one element should be configured as a broadcaster. If
a broadcast is activated by a device that has been designated as
a network broadcaster, then broadcasted time, date, and holiday
status will be updated over the CCN system. If broadcast is enabled, a broadcast acknowledger must also be enabled. The acknowledger cannot be the same machine as the broadcasting
machine.
ACTIVATE — The Activate variable enables the broadcast
function of the ComfortLink™ controls. If this variable is set to
0, this function is not used and holiday schedules and daylight
savings compensation are not possible. Setting this variable to
1 allows the machine to broadcast and receive broadcasts on
the network. The following information is broadcast: the time
with compensation for daylight savings, date, holiday flag, and
the outdoor-air temperature.
Set this variable to 2 for stand-alone units that are not connected to a CCN. With this configuration, daylight saving time
and holiday determination will be done without broadcasting
through the bus. This variable can only be changed when using
the Touch Pilot display, ComfortVIEW™ software, or Network Service Tool. This variable cannot be changed with the
Navigator display.
DISPLAY NAME
PATH
Broadcast acknowledger
ConfigCtlt-ID
LINE
NO.
10
VALUE
Yes
Alarm Control
ALARM ROUTING CONTROL — Alarms recorded on the
chiller can be routed through the CCN. To configure this option, the ComfortLink controls must be configured to determine which CCN elements will receive and process alarms. Input for the decision consists of eight digits, each of which can
be set to either 0 or 1. Setting a digit to 1 specifies that alarms
will be sent to the system element that corresponds to that digit.
Setting all digits to 0 disables alarm processing. The factory default is 00000000. See Fig. 30. The default setting is is based
on the assumption that the unit will not be connected to a network. If the network does not contain a ComfortVIEW, ComfortWORKS®, TeLink, DataLINK™, or BACLink module,
enabling this feature will only add unnecessary activity to the
CCN Communication Bus.
This option can be modified by the Touch Pilot display. It
cannot be modified with the Navigator display.
Typical configuration of the Alarm Routing variable is
11010000. This Alarm Routing status will transmit alarms to
ComfortView software, TeLink, BACLink, and DataLINK.
To configure this option with the Touch Pilot display:
DISPLAY NAME
PATH
Alarm Routing
ConfigALARMDEF
Control
46
LINE
NO.
VALUE
1
Default = 00000000
DESCRIPTION
Alarm Routing
0
0
0
STATUS
0
0
0
0
0
POINT
ALRM_CNT
ComfortView™, or ComfortWorks®
TeLink
Unused
BacLink or DataLink™
Unused
a30-4485
Fig. 30 — Alarm Routing Control
characters in length. This variable can only be changed when
using the Touch Pilot display, ComfortVIEW, or Network
Service Tool. This variable cannot be changed with the
Navigator display.
To configure this option with the Touch Pilot display:
ALARM EQUIPMENT PRIORITY — The ComfortVIEW
software uses the equipment priority value when sorting alarms
by level. The purpose of the equipment priority value is to determine the order in which to sort alarms that have the same
level. A priority of 0 is the highest and would appear first when
sorted. A priority of 7 would appear last when sorted. For example, if two chillers send out identical alarms, the chiller with
the higher priority would be listed first. The default is 4. This
variable can only be changed when using the Touch Pilot display, ComfortVIEW software, or Network Service Tool. This
variable cannot be changed with the Navigator™ display. To
configure this option with the Touch Pilot™ display:
DISPLAY NAME
PATH
LINE
NO.
Alarm Equipment
Priority
ConfigALARMDEF
2
VALUE
Range = 0 to 7
Default = 4
DISPLAY NAME
Alarm System
Name
Comm Failure
Retry Time
PATH
ConfigALARMDEF
LINE
NO.
VALUE
3
Range =
1 to 240 minutes
Default =
10 minutes
PATH
LINE
NO.
VALUE
Realarm
Time
ConfigALARMDEF
4
Range = 1 to 254 minutes
255 = Re-Alarm Disabled
Default = 30 minutes
VALUE
ConfigALARMDEF
5
Default =
PRO_RGRW
chiller control contains software which can automatically correct for daylight saving time. This software is accessible from
the Touch Pilot display, ComfortVIEW, or Network Service
Tool. It is not accessible through the Navigator display.
To enable this feature, Daylight Saving Select must be set to
1. The start of Daylight Saving must be configured by setting
the Month, Day of Week, and Week of Month. The end for
Daylight Saving must also be configured. To configure this option with the Touch Pilot display, see Table 36.
Table 36 — Daylight Savings Time Configuration
DISPLAY NAME
PATH
LINE
NO.
ConfigBRODEFS
1
ConfigBRODEFS
7
ConfigBRODEFS
8
Month
ConfigBRODEFS
9
Day of Week
(1=Monday)
ConfigBRODEFS
10
Week of Month ConfigBRODEFS
11
Leaving
ConfigBRODEFS
12
Month
ConfigBRODEFS
13
Day of Week
(1=Monday)
ConfigBRODEFS
14
Week of Month ConfigBRODEFS
15
Activate
Daylight
Saving Select
Entering
RE-ALARM TIME — This variable specifies the amount of
time that will be allowed to elapse between re-alarms. A realarm occurs when the conditions that caused the initial alarm
continue to persist for the number of minutes specified in this
decision. Re-alarming will continue to occur at the specified interval until the condition causing the alarm is corrected. This
variable can only be changed with the Touch Pilot display,
ComfortVIEW, or Network Service Tool. This variable cannot
be changed with the Navigator display. To configure this option
with the Touch Pilot display:
DISPLAY
NAME
LINE
NO.
Daylight Saving Time Configuration — The 30XA
COMMUNICATION FAILURE RETRY TIME — This variable specifies the amount of time that will be allowed to elapse
between alarm retries. Retries occur when an alarm is not
acknowledged by a network alarm acknowledger, which may
use either ComfortVIEW software or TeLink. If acknowledgement is not received, the alarm will be re-transmitted after the
number of minutes specified in this decision. This variable can
only be changed with the Touch Pilot display, ComfortVIEW,
or Network Service Tool. This variable cannot be changed with
the Navigator display. To configure this option with the Touch
Pilot display:
DISPLAY NAME
PATH
VALUE
1 or 2
Default = 2
Enable
Default = Dsble
Enter Starting
Month for
Daylight Saving
Enter the Day of
the Week Daylight
Saving Starts
Enter Week of
the Month Daylight
Saving Starts
Enter Ending
Month for
Daylight Saving
Enter the Day of
the Week Daylight
Saving ends
Enter Week of
the Month Daylight
Saving ends
Capacity Control Overrides — The following capacity control overrides (Active Capacity Override, CAP.S)
will modify the normal operation routine. If any of the override
conditions listed below are satisfied, the override will determine the capacity change instead of the normal control. Overrides are listed by priority order and are often linked to unit
ALARM SYSTEM NAME — This variable specifies the
system element name that will appear in the alarms generated
by the unit control. The name can be up to 8 alphanumeric
47
operating modes. See Table 37 for a list of overrides. See the
Operating Modes section on page 68 for more information regarding operating modes.
Override #1: Cooler Freeze Protection — This override attempts to avoid the freeze protection alarm. If the Leaving
Water Temperature is less than Brine Freeze Set Point (Brine
Freeze Setpoint, LOSP) + 2.0° F (1.1º C) then a stage of
capacity is removed.
NOTE: The freeze set point is 34 F (1.1 C) for fresh water
systems (Cooler Fluid Type, FLUD=1). The freeze set point
is Brine Freeze Set Point (Brine Freeze Setpoint, LOSP), for
Medium Temperature Brine systems (Cooler Fluid Type,
FLUD=2).
Override #2: Circuit A Low Saturated Suction Temperature
in Cooling
Override #3: Circuit B Low Saturated Suction Temperature
in Cooling
Override #4: Circuit C Low Saturated Suction Temperature
in Cooling — These overrides attempt to avoid the low suction
temperature alarms and are active only when the compressor is
running beyond the fully unloaded level. The slide valve in the
affected circuit will be decreased in position if the Saturated
Suction Temperature is less than Brine Freeze Set Point (Brine
Freeze Setpoint, LOSP) –18.0 F (–10 C) for 90 seconds, or the
Saturated Suction Temperature is less than –4 F (–20 C).
Override #5: Low Temperature Cooling and High Temperature Heating — This override decreases capacity when the difference between the Control Point (Control Point, CTPT) and
the Leaving Water Temperature (Cooler Leaving Fluid, LWT)
reaches a predetermined limit and the rate of change of the water is 0º F per minute or still decreasing.
Override #6: Low Temperature Cooling and High Temperature
Heating — This override decreases capacity (approximately
5% of circuit capacity) when the Entering Water Temperature
(Cooler Entering Fluid, EWT) is less than the Control Point
(Control Point, CTPT).
Override #7: Ramp Loading — No capacity stage increase
will be made if the unit is configured for ramp loading (Ramp
Loading Select, RL.S=ENBL) and the difference between the
Leaving Water Temperature and the Control Point is greater
than 4º F (2.2º C) and the rate of change of the leaving water is
greater than Cool Ramp Loading Rate (Cooling Ramp Loading, CRMP). Operating mode 5 (MD05) will be in effect.
Override #8: Service Manual Test Override — This override mode places the unit into Service Test mode. The user can
then use Service Test functions to test the unit. All safeties and
higher priority overrides are monitored and acted upon.
Override # 9: Demand Limit — This override mode is active
when a command to limit the capacity is received. If the
current unit capacity is greater than the active capacity limit
value, a stage is removed. If the current capacity is lower than
the capacity limit value, the control will not add a stage that
will result in the new capacity being greater then the capacity
limit value. Operating mode 4 (MD04) will be in effect.
Override #10: Cooler Interlock Override — This override
prohibits compressor operation until the Cooler Interlock
(Cooler Flow Switch, LOCK) is closed.
Override #11: High Temperature Cooling and Low Temperature Heating — This override algorithm runs once when the
unit is switched to ON. If the difference between the Leaving
Water Temperature (Cooler Leaving Fluid, LWT) and the
Control Point (Control Point, CTPT) exceeds a calculated
value and the rate of change of the water temperature is greater
than –0.1º F/min, a stage will be added.
Table 37 — Capacity Control Overrides
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
77
48
CAPACITY CONTROL OVERRIDES
Cooler Freeze Protection
Circuit A Low Saturated Suction Temperature in Cooling
Circuit B Low Saturated Suction Temperature in Cooling
Circuit C Low Saturated Suction Temperature in Cooling
Low Temperature Cooling and High Temperature Heating (LWT)
Low Temperature Cooling and High Temperature Heating (EWT)
Ramp Loading
Service Manual Test Override
Demand Limit
Cooler Interlock Override
High Temperature Cooling and Low Temperature Heating
High Temperature Cooling and Low Temperature Heating
(minimum load control in effect)
Minimum On/Off and Off/On Time Delay
Slow Change Override
System Manager Capacity Control
Circuit A High Pressure Override
Circuit B High Pressure Override
Circuit C High Pressure Override
Standby Mode
—
—
Minimum On Time Delay
Circuit A Low Saturated Suction Temperature in Cooling
Circuit B Low Saturated Suction Temperature in Cooling
Circuit C Low Saturated Suction Temperature in Cooling
Circuit A High Discharge Gas Override
Circuit B High Discharge Gas Override
Circuit C High Discharge Gas Override
—
—
—
—
—
Circuit A Low Refrigerant Charge
Circuit B Low Refrigerant Charge
Circuit C Low Refrigerant Charge
—
—
—
—
Circuit A High Current Override
Circuit B High Current Override
Circuit C High Current Override
Circuit A High Suction Superheat at Part Load
Circuit B High Suction Superheat at Part Load
Circuit C High Suction Superheat at Part Load
—
—
—
Circuit A MCHX MOP Control
Circuit B MCHX MOP Control
Circuit C MCHX MOP Control
Circuit A Delay for Unloading the Slide Valve
Circuit B Delay for Unloading the Slide Valve
Circuit C Delay for Unloading the Slide Valve
Circuit A Delay for Refrigeration Isolation Valve to Open
Circuit B Delay for Refrigeration Isolation Valve to Open
Circuit C Delay for Refrigeration Isolation Valve to Open
Circuit A Low Oil Level
Circuit B Low Oil Level
Circuit C Low Oil Level
Circuit A High Motor Temperature Override
Circuit B High Motor Temperature Override
Circuit C High Motor Temperature Override
Boostload Function
freeze set point is Brine Freeze Set Point (Brine Freeze
Setpoint, LOSP), for Medium Temperature Brine
systems (Cooler Fluid Type, FLUD=2).
If any of these conditions are met, the appropriate operating
mode, 21 (Circuit A), 22 (Circuit B) or 23 (Circuit C) will be in
effect.
Override #26: Circuit A High Discharge Gas Override
Override #27: Circuit B High Discharge Gas Override
Override #28: Circuit C High Discharge Gas Override —
When the temperature is above the limit curve minus 2° F
(1.1° C) increase in capacity will not be allowed. This override
will remain active until the discharge gas temperature drops
below the limit curve by –3° F (–1.7° C).
Override #34: Circuit A Low Refrigerant Charge
Override #35: Circuit B Low Refrigerant Charge
Override #36: Circuit C Low Refrigerant Charge — The capacity override attempts to protect the compressor from starting with no refrigerant in the circuit. This algorithm runs only
when the circuit is not operational (compressor is OFF). There
are several criteria that will enable this override:
1. The saturated suction temperature or saturated discharge
temperature is less than –13 F (–10.6 C).
2. All of these conditions must be true:
a. The saturated suction temperature or saturated
discharge temperature is less than leaving water
temperature by more than 5.4º F (3.0º C).
b. Saturated suction temperature or saturated discharge temperature is less than 41 F (5 C).
c. Outdoor air temperature is less than 32 F (0º C).
d. Saturated suction temperature or saturated discharge
temperature is less than the outdoor air temperature
by more than 5.4º F (3.0º C).
3. All of these conditions must be true:
a. The saturated suction temperature or saturated
discharge temperature is less than leaving water
temperature by more than 5.4º F (3.0º C).
b. Saturated suction temperature or saturated discharge temperature is less than 41 F (5 C).
c. Saturated suction temperature or saturated discharge temperature is less than the brine freeze
point (Brine Freeze Setpoint, LOSP) by more
than 6º F (3.3º C).
NOTE: The freeze set point is 34 F (1.1 C)
for fresh water systems (Brine Freeze Setpoint,
FLUD=1). The freeze set point is brine freeze set
point (Brine Freeze Setpoint, LOSP), for medium
temperature brine systems (Cooler Fluid Type,
FLUD=2).
4. All of these conditions must be true:
a. The saturated suction temperature or saturated
discharge temperature is less than leaving water
temperature by more than 5.4º F (3.0º C).
b. Saturated suction temperature or saturated discharge
temperature is less than 41 F (5 C).
c. Saturated suction temperature or saturated discharge
temperature is less than the outdoor-air temperature
by more than 9º F (5º C).
If any of these conditions 1, 2, 3 or 4 are met, the appropriate operating mode, 21 (Circuit A), 22 (Circuit B) or 23
(Circuit C) will be in effect.
Override #41: Circuit A High Current Override
Override #42: Circuit B High Current Override
Override #43: Circuit C High Current Override — This override attempts to avoid an overcurrent failure. The algorithm is
run every 4 seconds. If the compressor current is greater than
79% of must trip amps (MTA) but less than 85% MTA then the
Override #12: High Temperature Cooling and Low Temperature Heating — This override runs only when Minimum
Load Control is Enabled, (Hot Gas Bypass Select, HGBP)
and is set to 1, 2 or 3. This override will add a stage of capacity
if the next stage is Minimum Load Control, when the difference between the Leaving Water Temperature (Cooler Leaving Fluid, LWT) and the Control Point (Control Point, CTPT)
exceeds a calculated value and the rate of change of the water
temperature is greater than a fixed value.
Override #13: Minimum On/Off and Off/On Time Delay —
Whenever a capacity change has been made, the control will
remain at this capacity stage for the next 90 seconds. During
this time, no capacity control algorithm calculations will be
made. If the capacity step is a compressor, an additional
90-second delay is added to the previous hold time (see Override #22). This override allows the system to stabilize before
another capacity stage is added or removed. If a condition of a
higher priority override occurs, the higher priority override will
take precedence. Operating Mode 10 (MD10) will be in effect.
Override #14: Slow Change Override — This override prevents compressor stage changes when the leaving temperature
is close to the control point and slowly moving towards it.
Override #15: System Manager Capacity Control — If a
Chillervisor module is controlling the unit and multiple chillers, the unit will increase capacity to attempt to load to the demand limited value.
Override #16: Circuit A High Pressure Override
Override #17: Circuit B High Pressure Override
Override #18: Circuit C High Pressure Override — This override attempts to avoid a high pressure failure. The algorithm is
run every 4 seconds. If the Saturated Condensing Temperature
for the circuit is above the High Pressure Threshold (High
Pressure Threshold, HP.TH) then the position of slide valve
will be unloaded.
Override #19: Standby Mode — This override algorithm will
not allow a compressor to run if the unit is in Standby mode,
(Heat/Cool Status, HC.ST=2).
Override #22: Minimum On Time Delay — In addition to
Override #13 Minimum On/Off and Off/On Time Delay, for
compressor capacity changes, an additional 90-second delay
will be added to Override #13 delay. No compressor will be
deenergized until 3 minutes have elapsed since the last compressor has been turned ON. When this override is active, the
capacity control algorithm calculations will be performed, but
no capacity reduction will be made until the timer has expired.
A control with higher precedence will override the Minimum
On Time Delay.
Override #23: Circuit A Low Saturated Suction
Temperature in Cooling
Override #24: Circuit B Low Saturated Suction
Temperature in Cooling
Override #25: Circuit C Low Saturated Suction
Temperature in Cooling — If the circuit is operating close to
the operational limit of the compressor, the circuit capacity will
remain at the same point or unload to raise the saturated suction
temperature. This algorithm will be active if the circuit is on and
one of the following conditions is true:
1. Saturated Suction Temperature is less than the Brine
Freeze Setpoint (Brine Freeze Setpoint, LOSP) –6º F
(3.3º C).
2. Saturated Suction Temperature is less than the Brine
Freeze Setpoint (Brine Freeze Setpoint, LOSP) and the
circuit approach (Leaving Water Temperature – Saturated
Suction Temperature) is greater than 15º F (8.3º C) and
the Circuit Superheat (Discharge Gas Temperature – Saturated Discharge Temperature) is greater than 25º F
(13.9º C).
NOTE: The freeze set point is 34 F (1.1 C) for fresh
water systems (Cooler Fluid Type, FLUD=1). The
49
Override #77: Boostload Function — This override can be
present when boostload function is enabled. It is set in the following conditions :
if cool_lwt > ctrl_pnt + 5.4 and cool_ewt > ctrl_pnt + 9.0
and demand limit > 99%.
capacity will be held at current capacity. If the compressor current is greater than 85% MTA then capacity will be reduced by
repositioning the slide valve until the current is less than 85%
MTA (Must Trip Amps, MTA.X).
Override #44: Circuit A High Suction Superheat at Part Load
Override #45: Circuit B High Suction Superheat at Part Load
Override #46: Circuit C High Suction Superheat at Part Load
— If the compressor of the circuit is on, the compressor current
is no more than 30% of the MTA, main EXV is more than 90%
open and the suction superheat is higher than the superheat
control point for more than 5 minutes, then the circuit will be
shut down.
Override #50: Circuit A MCHX MOP Control Override
Override #51: Circuit B MCHX MOP Control Override
Override #52: Circuit C MCHX MOP Control Override —
This override shall prevent the compressor from increasing capacity when saturated suction temperature is greater than the
MOP setpoint and saturated condensing temperature is greater
than the maximum condensing temperature setpoint minus
15 F on units equipped with MCHX condenser option. This is
to avoid high pressure alarm and operation outside the compressor envelope.
Override #53: Circuit A Delay for Unloading the Slide Valve
Override #54: Circuit B Delay for Unloading the Slide Valve
Override #55: Circuit C Delay for Unloading the Slide
Valve — This override prevents the compressor from re-starting with locked rotor failure after being shutdown due to an
alarm or power cycle. The delay varies depending on the size
of the compressor. Refer to Table 38 for compressor nominal
capacities. A delay of 20 minutes will elapse for 165 and
185 ton compressors, a delay of 8 minutes will elapse for 90
and 120 ton compressors, and 5 minutes will elapse for 45 and
50 ton compressors. The delay allows the slide valve of the
compressor to move back to its fully unloaded position. The
delay is adjusted according to the percent of the compressor
running capacity before it is shut down. If the compressor is
stopped normally, no delay will be applied. If the compressor is
shut down by the locked rotor alarm, a full delay will be applied before the compressor is allowed to re-start. See Table 38
for compressor nominal capacity.
Override #56: Circuit A Delay for Refrigeration Isolation
Valve to Open
Override #57: Circuit B Delay for Refrigeration Isolation
Valve to Open
Override #58: Circuit C Delay for Refrigeration Isolation
Valve to Open — This override allows the discharge motorized ball valve to open before the compressor starts. The delay
is 2 minutes and 30 seconds. (Does not apply to units with DX
cooler option.)
Override #59: Circuit A Low Oil Level
Override #60: Circuit B Low Oil Level
Override #61: Circuit C Low Oil Level — This override is
only effective when the circuit is not running. The override will
prevent the circuit from starting up with a low oil level. If this
override occurs three times, the low oil level alarm will be
tripped.
Override #62: Circuit A High Motor Temperature Override
Override #63: Circuit B High Motor Temperature Override
Override #64: Circuit C High Motor Temperature Override
— This override prevents the compressor motor temperature
from rising above the high temperature limit, but still allows
the chiller to run close to the high temperature limit by unloading the compressor. If the motor temperature is greater than
214 F (101.1 C), the compressor will not load. This override
will remain active until the temperature drops below 214 F
(101.1 C). If the motor temperature is greater than 225 F
(107.2 C) for 60 seconds, the circuit capacity will decrease by
one stage. If the motor temperature is greater than 228 F
(108.9), the circuit capacity will decrease by one stage immediately.
Head Pressure Control — The Main Base Board
(MBB) controls the condenser fans to maintain the lowest
condensing temperature possible, and thus, the highest unit efficiency. The MBB uses the saturated condensing temperature
input from the discharge pressure transducer to control the
fans. Head pressure control is maintained through a calculated
set point which is automatically adjusted based on actual
saturated condensing and saturated suction temperatures so that
the compressor(s) is (are) always operating within the manufacturer’s specified envelope (see Fig. 31). Each time a fan is
added, the calculated head pressure set point will be raised
25° F (13.9° C) for 35 seconds to allow the system to stabilize.
The control will automatically reduce the unit capacity as the
saturated condensing temperature approaches an upper limit.
See capacity overrides #16-18. The control will indicate
through an operating mode that high ambient unloading is in
effect. If the saturated condensing temperature in a circuit exceeds the calculated maximum, the circuit will be stopped. For
these reasons, there are no head pressure control methods or set
points to enter. The control will turn off a fan stage when the
condensing temperature is below the minimum head pressure
requirement for the compressor. Fan sequences are shown in
Fig. 31. See Table 38 for compressor nominal capacity.
LOW AMBIENT TEMPERATURE HEAD PRESSURE
CONTROL OPTION — Units will start and operate down to
32 F (0° C) as standard. Operation to –20 F (–29 C) requires
optional low ambient head pressure control as well as wind
baffles (field fabricated and installed on all units for operation
below 32 F [0° C]) if wind velocity is anticipated to be greater
than 5 mph (8 kp/h). Inhibited propylene glycol or other suitable corrosion-resistant anti-freeze solution must be field supplied and installed in all units for unit operation below 34 F
(1.1 C). Solution must be added to fluid loop to protect loop
down to 15° F (8.3° C) below minimum operating ambient
temperature. Concentration should be based on expected minimum temperature and either “Burst” or “Freeze” protection
levels. At least 6 gal per ton (6.5 l/kW) of water volume is the
recommended minimum for a moderate system load.
For low-ambient temperature operation, the lead fan on a
circuit can be equipped with low ambient temperature head
pressure control option or accessory. The controller adjusts fan
speed to maintain the calculated head pressure set point.
LOW AMBIENT TEMPERATURE HEAD PRESSURE
CONTROL OPERATING INSTRUCTIONS — The 30XA
low ambient control is a variable speed drive (VFD) that varies
the speed of the lead condenser fan in each circuit to maintain
the calculated head pressure control set point. The fan speed
varies in proportion to the 0 to 10 vdc analog signal produced
by the AUX1 fan board. The display indicates motor speed in
Hz by default.
Table 38 — 30XA Compressor Nominal Capacity
30XA
080, 090, 100, 110, 120, 140, 160, 180, 200, 220,
UNIT SIZE 082 092 102 112 122 142 162 182 202 222
Compressor Nominal Capacity (tons)
Circuit A
45
45
50
60
60
90 100 90 100 120
Circuit B
45
45
50
50
60
50
60 90 100 100
Circuit C
—
—
—
—
—
—
—
—
—
—
30XA
240, 260, 280, 300,
UNIT SIZE
242 262 282 302
Compressor Nominal Capacity (tons)
Circuit A
120 165 165 185
Circuit B
120 100 120 120
Circuit C
—
—
—
—
50
325,
327
350,
352
400
450
500
165
165
—
185
165
—
120
120
165
185
90
185
185
120
185
CIRCUIT STAGE
CIRCUIT
Fan stage A
COMP B
FM1
COMP A
FM3
FM2
A
FM5
FM4
FM6
B
30XA080,082
COMP B
COMP A
A
FM1
FM3
FM5
FM7
FM2
FM4
FM6
FM8
B
30XA090-122
COMP B
COMP A
PEB
A
3
Contactor #
FC B1 FC B2 FC B3
Fan position
FM1
FM4
FM2
Fan stage A
1
2
3
Contactor #
Fan position
FM7
FM5
FM8
FM6
Fan stage B
1
2
3
4
Contactor #
FC B1 FC B2 FC B3 FC B4
Fan position
FM1
FM3
FM2
FM4
Fan stage A
1
2
3
4
Contactor #
Fan position
FM9
FM7
FM5
FM10
FM10
Fan stage B
1
2
3
4
PEB
COMP A
A
FM5
FM7
FM9
FM11
FM2
FM4
FM6
FM8
FM10
FM12
COMP A
PEB
FM1
FM3
FM5
FM2
FM4
FM6
FM7
FM9
FM11 FM13
FM10
FM12 FM14
A
PEB
FM7
FM1
FM3
FM5
FM2
FM4
FM6
COMP A
FM9
FM11 FM13 FM15
FM10
FM12 FM14 FM16
A
30XA260,262
COMP B
FM3
PEB
FM7
FM5
FM4
FM8
FM6
FM9
FM10
COMP A
A
FM11 FM13 FM15
FM12 FM14 FM16
30XA280,282
FM3
FM7
FM5
FM4
PEB
FM6
FM8
FM9
FM10
COMP A
A
FM6
FM7
FM8
FM9
FM10
FM2
FM4
2
3
4
5
6
Contactor #
FC A1 FC A2 FC A3 FC A4 FC A5 FC A6
Fan position
FM11
FM9
FM7
Fan stage B
1
2
3
Contactor #
FM12 FM10
4
5
FM8
6
FC B1 FC B2 FC B3 FC B4 FC B5 FC B6
Fan position
FM1
FM3
FM5
FM2
FM4
FM6
Fan stage A
1
2
3
4
5
6
7
Contactor #
FC A1 FC A2 FC A3 FC A4 FC A5 FC A6 FC A7
Fan position
FM13 FM11
Contactor #
1
2
FM9
FM7
3
4
FM14 FM12 FM10
5
6
FC B1 FC B2 FC B3 FC B4 FC B5 FC B6
Fan position
FM1
FM3
FM5
FM2
FM4
FM6
Fan stage A
1
2
3
4
5
6
7
8
Contactor #
FC A1 FC A2 FC A3 FC A4 FC A5 FC A6 FC A7 FC A8 FC A9
Fan position
FM15 FM13 FM11
Contactor #
1
2
3
FM9
FM7
4
5
FM16 FM14 FM12 FM10
6
FC B1 FC B2 FC B3 FC B4 FC B5 FC B6
Fan position
FM1
FM3
FM5
FM2
FM4
FM6
Fan stage A
1
2
3
4
5
6
7
8
Contactor #
FC A1 FC A2 FC A3 FC A4 FC A5 FC A6 FC A7 FC A8 FC A9
Fan position
FM15 FM13 FM11
Contactor #
1
2
3
FM9
FM7
4
5
FM16 FM14 FM12 FM10
6
7
FC B1 FC B2 FC B3 FC B4 FC B5 FC B6 FC B7
Fan position
FM1
FM3
FM5
FM8
FM2
FM4
Fan stage A
1
2
3
4
5
6
FM6
7
8
FM11 FM13 FM15
Fan position
FM15 FM13 FM11
FM12 FM14 FM16
Fan stage B
PEB
COMP A
A
FM11 FM13 FM15 FM17
Contactor #
1
FM12 FM14 FM16 FM18
30XA325-352
3
FM9
FM7
4
5
FM16 FM14 FM12 FM10
6
FC B1 FC B2 FC B3 FC B4 FC B5 FC B6
FM1
FM3
FM5
FM2
FM4
FM6
Fan stage A
1
2
3
4
5
6
7
8
Contactor #
FC A1 FC A2 FC A3 FC A4 FC A5 FC A6 FC A7 FC A8 FC A9
Fan position
FM17 FM15 FM13 FM11
Contactor #
1
2
3
4
FM9
5
FM18 FM16 FM14 FM12
6
7
8
FC B1 FC B2 FC B3 FC B4 FC B5 FC B6 FC B7 FC B8 FC B9
Fan position
LEGEND
FM
— Fan Motor
PEB — Power Electrical Box
Fig. 31 — Fan Staging
51
2
Fan position
Fan stage B
B
Compressor
Fan Contactor
FM6
FC A1 FC A2 FC A3 FC A4 FC A5 FC A6 FC A7 FC A8 FC A9 FC A10
B
FM5
FM8
Contactor #
30XA300,302
COMP B
FM3
1
Fan stage B
B
COMP B
FM1
Fan stage A
Fan stage B
B
6
FC B1 FC B2 FC B3 FC B4
Fan position
Fan stage B
30XA220-242
COMP B
Contactor #
5
FC A1 FC A2 FC A3 FC A4 FC A5 FC A6
FM8
B
COMP —
FC
—
4
FC A1 FC A2 FC A3 FC A4
FM6
FM3
FM4
FM6
2
FM4
COMP B
FM2
FM3
1
FM2
FM1
FM3
FM5
Fan stage B
FM9
30XA180-202
FM1
Fan position
FM7
B
FM2
3
FM5
COMP B
FM1
2
FM3
B
FM2
1
FC A1 FC A2 FC A3
FM1
30XA140-162
FM1
Contactor #
FM1
FM3
FM5
FM7
FM10
FM2
FM4
FM6
FM8
FM8
CIRCUIT STAGE
CIRCUIT
Fan stage A
A
COMP B
PEB A/B
COMP A
FM3
FM5
FM7
FM9
FM11 FM13 FM15 FM17 FM19
FM2
FM4
FM6
FM8
FM10
FM12 FM14 FM16 FM18 FM20
a30-4219
B
30XA400
C
a30-4220
PEB A/B
COMP A
PEB C
A
COMP C
FM1
FM3
FM5
FM7
FM9
FM11 FM13 FM15 FM17 FM19 FM21
FM2
FM4
FM6
FM8
FM10
FM12 FM14 FM16 FM18 FM20 FM22
B
30XA450, 500
a30-4221
COMP —
FC
—
2
3
4
5
6
FC A1 FC A2 FC A3 FC A4 FC A5 FC A6
Fan position
FM11
FM9
FM7
FM12
FM10
FM8
Fan stage B
1
2
3
4
5
6
7
8
7
8
COMP C
PEB
FM1
COMP B
1
Contactor #
C
Contactor #
FC B1 FC B2 FC B3 FC B4 FC B5 FC B6
Fan position
FM1
FM3
FM5
FM2
FM4
FM6
Fan stage C
1
2
3
4
5
6
Contactor #
FC C1 FC C2 FC C3 FC C4 FC C5 FC C6 FC C7 FC C8
Fan position
FM19
FM17
FM15
FM13
FM20
FM18
FM16
FM14
Fan stage A
1
2
3
4
5
6
7
8
Contactor #
FC A1 FC A2 FC A3 FC A4 FC A5 FC A6 FC A7 FC A8
Fan position
FM13
FM11
FM9
FM7
FM14
FM12
Fan stage B
1
2
3
4
5
6
Contactor #
FM10
FM8
7
8
FC B1 FC B2 FC B3 FC B4 FC B5 FC B6
Fan position
FM1
FM3
FM5
FM2
FM4
FM6
Fan stage C
1
2
3
4
5
6
Contactor #
FC C1 FC C2 FC C3 FC C4 FC C5 FC C6 FC C7 FC C8
Fan position
FM21
FM19
FM17
FM15
FM22
FM20
FM18
FM16
LEGEND
Compressor
FM
— Fan Motor
Fan Contactor
PEB — Power Electrical Box
Fig. 31 — Fan Staging (cont)
Operation — The low ambient temperature head pressure controller is pre-configured to operate from a 0 to 10 vdc analog
input signal present on terminals 3 (AIN+) and 4 (AIN–).
Jumpers between terminals 2 and 4 and terminals 5 and 8 (5
and 9 for 575-v drives) are required for proper operation. The
AOUT+ AOUT- P+ Ndrive is enabled based on an increase in the analog input signal
above 0 vdc. Output is varied from 0 Hz to 60 Hz as the analog
signal increases from 0 vdc to 10 vdc. When the signal is at
12 13 14 15
0 vdc the drive holds the fan at 0 rpm. The head pressure control set point is not adjustable. The MBB determines the conDIN1 DIN2 DIN3 24V+ 0V
trol set point as required.
ENABLE
8
7
6
5
9
JUMPER
Replacement — If the controller is replaced the parameters in
Table 39 must be configured. See Fig. 32 and 33.
10V+
1
L3
DIP Switch 2
50 / 60 Hz
kW / hp
ON = 60 Hz
ON
RLB RLC
10
11
0V AIN+ AIN-
2
3
4
L3
L2
N
L2
L1
JUMPER
D
C
D
+
C
+ –
0-10 VDC SIGNAL FROM FAN BOARD
L
L1
U
V
W
T1 T2 T3
a30-4049
a30-4230
Fig. 33 — Siemens Low Ambient Temperature
Control Signal Wiring
TO CONDENSER
FAN MOTOR
Fig. 32 — Siemens Low Ambient Temperature
Control Power Wiring
52
Table 39 — Siemens VFD Control Parameters
PARAMETER*
P0010
P0311
P0757
P0761
P3900
P0003
P1210
P1310
VALUE
1
1140†
850**
0.50
0.50
1
3
6
10%
CHANGING P0004 — PARAMETER FILTER FUNCTION
DESCRIPTION
Enter Quick Commissioning
STEP
Rated Motor Speed
Control Signal Scaling Offset
Control Signal Scaling Offset
End of Quick Commissioning
User Access Level
Automatic Restart
Continuous Boost
1
Press
2
Press
3
Press
*Remove jumper from terminals 5 and 8 (or terminals 5 and 9 for
P
RESULT ON
DISPLAY
to access parameters
until P0004 is displayed
P
to access the parameter
value level
575 v) before configuring parameter. Reinstall jumper after configuration is complete.
†High Ambient option.
**Standard.
The DIP switches must also be set. DIP switch 1 is not used
and DIP switch 2 is the motor frequency. (OFF = 50 Hz, ON =
60 Hz)
Drive Programming — Parameter values can be altered via
the operator panel. The operator panel features a five-digit,
seven-segment display for displaying parameter numbers and
values, alarm and fault messages, set points, and actual values.
See Fig. 34 and 35. See Table 40 for additional information on
the operator panel.
NOTE: The operator panel motor control functions are disabled by default. To control the motor via the operator panel,
parameter P0700 should be set to 1 and P1000 set to 1. The
operator panel can be fitted to and removed from the drive
while power is applied. If the operator panel has been set as the
I/O control (P0700 = 1), the drive will stop if the operator
panel is removed.
Changing Parameters with the Operator Panel — See Fig. 35
for the procedure for changing the value of parameter P0004.
Modifying the value of an indexed parameter is illustrated in
Fig. 35 using the example of P0719. Follow the same procedure to alter other parameters using the operator panel.
NOTE: In some cases when changing parameter values the
display on the operator panel displays P - - - - . This means the
drive is busy with tasks of higher priority.
4
Press
value
or
5
Press
value
6
Only the command parameters are
visible to the user.
P
to the required
to confirm and store the
CHANGING P0719 AN INDEXED PARAMETER
SELECTION OF COMMAND/SETPOINT SOURCE
STEP
1
Press
2
Press
3
Press
P
RESULT ON
DISPLAY
to access parameters
until P0719 is displayed
P
to access the parameter
value level
4
Press
5
Press
value
6
Press
value
7
Press
8
Press
P
to display current set value
or
P
to the required
to conform and store the
until r0000 is displayed
a30-4061
Fig. 34 — Siemens Low Ambient Temperature
Controller
P
to return the display to the
standard drive display (as defined by
the customer)
Fig. 35 — Changing Parameters
with the Operator Panel
53
13. The drive is now active. Check fan rotation prior to testing.
If the fan is spinning forward, further adjustment is needed.
Fan should sit still when commanded speed is 0%. If the
fan is spinning forward slightly, press P and
to
Parameter P0761. Press P and use
to change this
value to 0.1. Press P to accept. Check the fan. If rotation
has stopped no further adjustment is required. If the fan
is still rotating forward, press P and use
to change
this value to 0.2. Press P to accept. Repeat as needed
until the fan is holding still or is just barely moving in
either direction. Do NOT enter a value greater than 0.5
for this parameter without first contacting your Carrier
representative.
Changing Single Digits in Parameter Values — For changing the parameters value rapidly, the single digits of the display
can be changed by performing the following actions:
Ensure the operator panel is in the parameter value changing level as described in the Changing Parameters with the
Operator Panel section.
1. Press Fn (function button), which causes the farthest
right digit to blink.
2. Change the value of this digit by pressing
or
.
3. Pressing Fn (function button) again to cause the next
digit to blink.
4. Perform steps 2 to 4 until the required value is displayed.
5. Press P (parameter button) to exit the parameter value
changing level.
Troubleshooting with the Operating Panel — Warnings and
faults are displayed on the operating panel with Axxx and
Fxxx. The individual messages are shown in Table 41.
If the motor fails to start, check the following:
• Power is present on T1, T2 and T3.
• Configuration jumpers are in place.
• Control signal between 1 vdc and 10 vdc is present on
terminals 3 and 4.
• P0010 = 0.
• P0700 = 2.
Fault Messages (Tables 41 and 42) — In the event of a failure, the drive switches off and a fault code appears on the
display.
NOTE: To reset the fault code, one of the following methods
can be used:
1. Cycle the power to the drive.
2. Press the Fn button on the operator panel.
Schneider Altivar VFD Operation — The low ambient temperature head pressure controller is pre-configured to operate
from a 0 to 10 vdc analog input signal present on terminals
AI1 and COM. A jumper between terminals 24V and LI1 is required for proper operation. The drive is enabled based on an
increase in the analog input signal above 0 vdc. Output is varied from 0 Hz to 60 Hz as the analog signal increases from
0 vdc to 10 vdc. When the signal is at 0 vdc the drive holds the
fan at 0 rpm. The head pressure control set point is not adjustable. The MBB determines the control set point as required.
The operating panel is shown in Fig. 37. Refer to the Quick
Start Guide for how to access the programming mode, or the
documentation on CD-ROM (shipped with each VFD) for a
complete set of VFD parameters, fault codes and troubleshooting information.
Schneider Altivar VFD Replacement — For Altivar 21
VFDs, if the controller is replaced the parameters in Table 43
must be configured. It is recommended that the configuration
of the VFD is verified per Table 43 prior to proceeding. Also,
the following must be wired:
1. A jumper must be in place from terminal P24 to F.
2. Connect the red and black wires from fan board 0-10
VDC output to terminal VIA and CC respectively.
3. Connect the motor power wires T1, T2 and T3 respectively to terminal U/T1, V/T2 and W/T3 of the drive.
4. Connect the line power wires L1, L2 and L3 from control
box respectively to terminal R/L1, S/L2 and T/L3 of the
drive.
NOTE: The function button may also be used to acknowledge
a fault condition.
Quick Commissioning (P0010=1) — It is important that parameter P0010 is used for commissioning and P0003 is used to
select the number of parameters to be accessed. The P0010 parameter allows a group of parameters to be selected that will
enable quick commissioning. Parameters such as motor settings and ramp settings are included. At the end of the quick
commissioning sequences, P3900 should be selected, which,
when set to 1, will carry out the necessary motor calculations
and clear all other parameters (not included in P0010=1) to the
default settings. This will only occur in Quick Commissioning
mode. See Fig. 36.
Reset to Factory Default — To reset all parameters to the factory default settings, the following parameters should be set as
follows:
1. Jumpers must be in place from terminals 2 and 4 and 5
and 8 (5 and 9 for 575v drives only).
2. Remove the keypad (pull out from top) and verify that
DIP switch 1 is OFF and 2 is ON. Replace keypad.
3. Power up the drive. Press Parameter P key. Press
to Parameter P0010.
4. Press P , then
to change the 0 to a 1. Press
again to accept the change.
P
5. Press
to Parameter P0311. Press P and press
to change this value to 1140 for 6-pole motors
or 850 for units with 8-pole motors. Press P to accept.
6. Press
to Parameter P3900. Press P and use
to change this value to 1. Press P to accept.
7. The drive will finish standard programming. Remove one
end of the jumper wire from terminal 8.
8. Press P again and go to Parameter P0003. Press P
and use
to change this value to 3. Press P to
accept.
9. Press
to Parameter P1210. Press P and use
to change this value to 6. Press P to accept.
10. Press
to Parameter P1310. Press P and use
to change this value to 10%. Press P to accept.
11. Press the Function
will read 0.00 Hz.
Fn
key and then
P
. The display
12. Replace the wire jumper in terminal 8.
54
Table 40 — Siemens Low Ambient Temperature Controller Operator Panel
PANEL/BUTTON
FUNCTION
DESCRIPTION
Indicates Status
The LCD displays the settings currently used by the converter.
Start Converter
The Start Converter button is disabled by default. To enable this button set P0700 = 1.
Stop Converter
Press the Stop Converter button to cause the motor to come to a standstill at the selected
ramp down rate. Disabled by default, to enable set P0700 = 1.
Press the Stop Converter button twice (or hold) to cause the motor to coast to a standstill.
This function is always enabled.
Change Direction
Press the Change Direction button to change the direction of rotation of the motor.
Reverse is indicated by a minus (–) sign or a flashing decimal point. Disabled by default, to
enable set P0700 = 1.
Jog Motor
Press the Jog Motor button while the inverter has no output to cause the motor to start and
run at the preset jog frequency. The motor stops when the button is released. The Jog
Motor button is not enabled when the motor is running.
Functions
The Functions button can be used to view additional information. Press and hold the button to display the following information starting from any parameter during operation:
1. DC link voltage (indicated by d – units V).
2. Output current. (A)
3. Output frequency (Hz)
4. Output voltage (indicated by o – units V).
5. The value selected in P0005 (If P0005 is set to show any of the above [3, 4, or 5] then
this will not be shown when toggling through the menu).
Press the Functions button repeatedly to toggle through displayed values.
Jump Function
Press of the Fn button from any parameter (rXXXX or PXXXX) to immediately jump to
r0000, when another parameter can be changed, if required. Return to r0000 and press
the Functions button again to return.
0
jog
Fn
Access Parameters
Allows access to the parameters.
P
Increase Value
Press the Increase Value button to increase the displayed value. To change the Frequency
Setpoint using the operator panel set P1000 = 1.
Decrease Value
Press the Decrease Value button to decrease the displayed value. To change the
Frequency Setpoint using the operating panel set P1000 = 1.
55
P0010 Start Quick Commissioning
0 Ready to Run
1 Quick Commissioning
30 Factory Setting
NOTE: P0010 must always be set back to ‘0’ before operating
the motor. However if P3900 = 1 is set after commissioning this
is done automatically.
P0700 Selection of Command Source
(on/off/reverse)
0 Factory Setting
1 Basic Operator Panel
2 Terminal/Digital Inputs
P0100 Operation
0 Power in kW; f default 50 Hz
1 Power in hp; f default 60 Hz
2 Power in kW; f default 60 Hz
NOTE: Settings 0 and 1 should be changed using the DIP
switches to allow permanent setting.
P1000 Selection of Frequency Setpoint
0 No frequency setpoint
1 Operator panel frequency control 
2 Analog Setpoint
P1080 Min. Motor Frequency
Sets minimum motor frequency (0-650Hz) at which the motor
will run independent of the frequency setpoint. The value set
here is valid for both clockwise and counterclockwise rotation.
P0304 Rated Motor Voltage*
10 V — 2000 V
Nominal motor voltage (V) from rating plate
P0305 Rated Motor Current*
0 — 2 x inverter rated current (A)
Nominal motor current (A) from rating plate
P1082 Max. Motor Frequency
Sets maximum motor frequency (0-650Hz) at which the motor
will run at independent of the frequency setpoint. The value set
here is valid for both clockwise and counterclockwise rotation.
P0307 Rated Motor Power*
0 kW — 2000 kW
Nominal motor power (kW) from rating plate.
If P0100 = 1, values will be in hp
P1120 Ramp-Up Time
0 s - 650 s
Time taken for the motor to accelerate from standstill up to
maximum motor frequency.
P0310 Rated Motor Frequency*
12 Hz — 650 Hz
Nominal motor frequency (Hz) from rating plate
P1121 Ramp-Down Time
0 s - 650 s
Time taken for motor to decelerate from maximum motor
frequency down to a standstill.
P0311 Rated Motor Speed*
0 — 4000 1/min
Nominal motor speed (rpm) from rating plate
P3900 End Quick Commissioning
0 End Quick Commissioning without motor calculation or
factory reset.
1 End Quick Commissioning with motor calculation and
factory reset (Recommended)
2 End Quick Commissioning with motor calculation and with
I/O reset
3 End Quick Commissioning with motor calculation but
without I/O reset
*Motor-specific parameters — see motor rating plate.
NOTE: Shaded boxes are for reference only.
Fig. 36 — Siemens Low Ambient Temperature Controller Flow Chart Quick Commissioning
56
Table 41 — Siemens Low Ambient Temperature Controller Fault Messages
FAULT
F0001
Overcurrent
F0002
Overvoltage
F0003
Undervoltage
F0004
Drive
Overtemperature
F0005
Drive I2t
F0011
Motor
Overtemperature I2t
F0041
Stator Resistance
Measurement Failure
F0051
Parameter EEPROM Fault
F0052
Powerstack Fault
F0060
Asic Timeout
F0070
Communications
Board Set Point Error
F0071
No Data for
RS232 Link During
Telegram Off Time
F0072
No Data from
RS485 Link During
Telegram Off Time
F0080
Analog Input Lost Input Signal
F0085
External Fault
F0101
Stack Overflow
F0221
PI Feedback
Below Minimum Value
F0222
PI Feedback Above
Maximum Value
F0450
(Service Mode Only)
BIST Tests Failure
ASIC
BIST
BOP
I2t
PI
PID
—
—
—
—
—
—
POSSIBLE CAUSES
TROUBLESHOOTING
• Motor power does not correspond to the
inverter power
• Motor lead short circuit
• Ground fault
Check the following:
1. Motor power (P0307) must correspond to inverter power (P0206)
2. Motor cable and motor must have no short-circuits or ground faults
3. Motor parameters must match the motor in use
4. Motor must not be obstructed or overloaded
After Steps 1-4 have been checked, increase the ramp time (P1120) and reduce the
boost level (P1310, P1311, P1312).
Check the following:
• DC-link voltage (r0026) exceeds trip level
1. Supply voltage (P0210) must lie within limits indicated on rating plate
(P2172)
• Overvoltage can be caused either by too high 2. DC-link voltage controller must be enabled (P1240) and have parameters set
correctly
main supply voltage or if motor is in regenera3. Ramp-down time (P1121) must match inertia of load
tive mode
• Regenerative mode can be caused by fast
ramp downs or if the motor is driven from an
active load
• Main supply failed
Check the following:
• Shock load outside specified limits
1. Supply voltage (P0210) must lie within limits indicated on rating plate
2. Supply must not be susceptible to temporary failures or voltage reductions
• Ambient temperature outside of limits
Check the following:
• Fan failure
1. Fan must turn when inverter is running
2. Pulse frequency must be set to default value
3. Air inlet and outlet points are not obstructed
4. Ambient temperature could be higher than specified for the drive.
• Drive overloaded
Check the following:
• Duty cycle too demanding
1. Load duty cycle must lie within specified limits
• Motor power (P0307) exceeds drive power
2. Motor power (P0307) must match drive power (P0206)
capability (P0206)
• Motor overloaded
1. Check motor data
• Motor data incorrect
2. Check loading on motor
• Long time period operating at low speeds
3. Boost settings too high (P1310,P1311, P1312)
4. Check parameter for motor thermal time constant
5. Check parameter for motor I2t warning level
Stator resistance measurement failure
1. Check if the motor is connected to the drive
2. Check that the motor data has been entered correctly
Reading or writing of the non-volatile parameter
storage has failed
Reading of the powerstack information has
failed or the data is invalid
Internal communications failure
1. Factory reset and new parameters set
2. Replace drive
Replace drive
No setpoint received from communications
board during telegram off time
1.
2.
1.
2.
No response during telegram off time via
BOP link
1. Check connections to the communications board
2. Check the master
No response during telegram off time via
COM link
1. Check connections to the communications board
2. Check the master
• Broken wire
• Signal out of limits
Check connection to analog input
External fault is triggered via terminal inputs
Disable terminal input for fault trigger
Software error or processor failure
1.
2.
1.
2.
PID Feedback below minimum value P2268
PID Feedback above maximum value P2267
Acknowledge fault
Replace drive if repeated
Check connections to the communications board
Check the master
Run self test routines
Replace drive
Change value of P2268
Adjust feedback gain
1. Change value of P2267
2. Adjust feedback gain
1. Inverter may run but certain actions will not function correctly
Fault value
1 Some of the power section tests have failed 2. Replace drive
2 Some of the control board tests have failed
4 Some of the functional tests have failed
8 Some of the IO module tests have failed
16 The Internal RAM has failed its check on
power-up
LEGEND
Application Specific Instruction
Built-in Self Test
Basic Operating Panel
Current Squared Time
Proportional Integral
Proportional Integral Derivative
NOTE: To reset the fault code, one of the following methods can be used:
1. Cycle the power to the drive.
2. Press the Fn
57
button on the operator panel.
Table 42 — Siemens Low Ambient Temperature Controller Alarm Messages
FAULT
A0501
Current Limit
POSSIBLE CAUSES
• Motor power does not correspond to the
drive power
• Motor leads are too short
• Ground fault
A0502
Overvoltage Limit
A0503
Undervoltage Limit
A0504
Drive
Overtemperature
A0505
Drive I2t
A0506
Drive Duty Cycle
A0511
Motor
Overtemperature I2t
A0541
Motor Data
Identification Active
A0600
RTOS Overrun Warning
• Mains supply too high
• Load regenerative
• Ramp-down time too short
• Mains supply too low
• Short mains interruption
Warning level of inverter heat-sink temperature
(P0614) is exceeded, resulting in pulse frequency reduction and/or output frequency
reduction (depending on parameters set
(P0610)
Warning level is exceeded; current will be
reduced if parameters set (P0610 = 1)
Heatsink temperature and thermal junction
model are outside of allowable range
Motor overloaded
Motor data identification (P1910) selected or
running
Software error
TROUBLESHOOTING
1. Check whether the motor power corresponds to the drive power
2. Check that the cable length limits have not been exceeded
3. Check motor cable and motor for short-circuits and ground faults
4. Check whether the motor parameters correspond with the motor being used
5. Check the stator resistance
6. Increase the ramp-up-time
7. Reduce the boost
8. Check whether the motor is obstructed or overloaded
1. Check that mains supply voltage is within allowable range
2. Increase ramp down times
NOTE: If the vdc-max controller is active, ramp-down times will be automatically
increased
Check main supply voltage (P0210)
1. Check if ambient temperature is within specified limits
2. Check load conditions and duty cycle
3. Check if fan is turning when drive is running
Check if duty cycle is within specified limits
Check if duty cycle is within specified limits
Check the following:
1. P0611 (motor I2t time constant) should be set to appropriate value
2. P0614 (motor I2t overload warning level) should be set to suitable level
3. Are long periods of operation at low speed occurring
4. Check that boost settings are not too high
Wait until motor identification is finished
—
LEGEND
I2 t
— Current Squared Time
RTOS — Run Time Operating System
1
4
2
5
RUN
3
%
PRG
Hz
MON
Loc
Rem
MODE
8
ENT
9
6
7
10
RUN
CALL
OUT
1
LED/KEY
Display
RUN LED
5
Display
PRG LED
Display
MON LED
Display
Unit
Display
Unit LED
6
Up/Down
arrows
2
3
4
7
8
Up/Down
LED
Loc/Rem
LED
STOP
12
11
13
14
CALL
OUT
DESCRIPTION
Illuminates when a run command is applied to the drive
controller. Flashes when a speed reference is present
with the run command.
Illuminates when Programming mode is active. Flashes
when -GrU menus are active.
Illuminates when Monitoring mode is active. Flashes in
fault record display mode.
4 digits, 7 segments
LED/KEY
MODE
9
10
11
12
13
The % LED illuminates when a displayed numeric
value is a percentage. The Hz LED illuminates when a
displayed numeric value is in hertz.
Depending on the mode, use the arrows to: navigate
between the menus, change a value, or change the
speed reference when Up/Down LED (7) is lit.
Illuminates when the Up/Down arrows are controlling
the speed reference.
Illuminates when Local mode is selected.
Loc/Rem
ENT
RUN LED
RUN
STOP
14
DESCRIPTION
Press to select the Keypad mode. Modes are: Run
mode (default on power-up), Programming mode, and
Monitoring mode. Can also be used to go back to the
previous menu.
Switches between Local and Remote modes.
Press to display a parameter’s value or to save a
changed value.
Illuminates when the Run key is enabled.
Pressing this key when the RUN LED is illuminated
starts the drive controller.
Stop/reset key. In Local mode, pressing the STOP key
causes the drive controller to stop based on the setting
of parameter F721. In Remote mode, pressing the
STOP key causes the drive controller to stop based on
the setting of parameter F603. The display will indicate
a flashing “E”. If F735 is set to 0 (default setting), pressing the stop key twice will reset all resettable faults if
the fault condition has been resolved.
Fig. 37 — Schnieder Altivar 21 VFD Display Panel
58
Table 43 — Schnieder Altivar 21 VFD Operating Parameters
PARAMETER
uLu
F201
F202
F203
F204
F401
F415
F417
F701
tHr
uL
FH
LL
UL
ACC
dEC
cnod
fnod
NAME
Rated Motor Voltage
VIA Speed Reference Level 1
VIA Output Frequency Level 1
VIA Speed Reference Level 2
VIA Output Frequency Level 2
Slip compensation
Rated Motor Current
Rated Motor Speed
Keypad display: % or A/V
Motor Rated Current Overload Setting
Rated Motor Frequency
Maximum Frequency
Low Speed
High Speed
Ramp-up Time
Ramp-down Time
Remote Mode Start/Stop Control
Remote Mode Primary Speed reference
Source
VALUE
Nominal motor voltage(V) from rating plate
5
0
100
60
60%
Nominal motor current(A) from rating plate
Nominal motor speed(RPM) from rating plate
1
Nominal motor current(A) from rating plate
60 Hz
60 Hz
0 Hz
60 Hz
10 Sec
10 Sec
0 (Control terminal logic inputs)
1 (VIA)
6. Electrical power source must agree with unit nameplate.
7. Oil separator heaters must be firmly seated under the oil
separator, and must be energized for 24 hours prior to
start-up.
8. Verify power supply phase sequence. Fan motors are 3
phase. Check rotation of non low-ambient controlled fans
by using the quick test. Fan rotation is counterclockwise
as viewed from top of unit. If fan is not turning counterclockwise, reverse 2 of the power wires at the main terminal block.
9. Perform service test to verify proper operation.
PRE-START-UP
IMPORTANT: Complete the Start-Up Checklist
for 30XA Liquid Chillers at the end of this publication.
The checklist assures proper start-up of a unit, and
provides a record of unit condition, application
requirements, system information, and operation at
initial start-up.
Do not attempt to start the chiller until the following checks
have been completed.
System Check
START-UP
1. Check auxiliary components, such as the chilled fluid
circulating pump, air-handling equipment, or other
equipment to which the chiller supplies liquid are operational. Consult manufacturer’s instructions. If the unit has
field-installed accessories, be sure all are properly
installed and wired correctly. Refer to unit wiring
diagrams.
2. Open compressor suction service valves (if equipped).
3. Open discharge line, liquid line, oil line, and economizer
(if equipped) service valves.
4. Fill the chiller fluid circuit with clean water (with recommended inhibitor added) or other non-corrosive fluid to be
cooled. Bleed all air out of high points of system. If outdoor temperatures are expected to be below 32 F (0° C),
and unit has a flooded cooler option, sufficient inhibited
propylene glycol or other suitable corrosion inhibited antifreeze should be added to the chiller water circuit to prevent possible freeze-up.
The chilled water loop must be cleaned before the unit is
connected. Units supplied with the accessory hydronic
package include a run-in screen. If the run-in screen is left
in the suction guide/strainer, it is recommended that the
Service Maintenance be set to alert the operator within
24 hours of start-up to be sure that the run-in screen in the
suction guide/strainer is removed. To set the time for the
parameter, go to Water Filter Ctrl (days), W.FIL. Values for this item are counted as days. Refer to the hydronic pump package literature if unit is equipped with the
optional hydronic pump package.
5. Check tightness of all electrical connections.
CAUTION
Do not manually operate contactors. Serious damage to the
machine may result.
Actual Start-Up — Actual start-up should be done only
under supervision of a qualified refrigeration technician.
1. Be sure all oil, suction valves, discharge valves (if
equipped) and liquid line service valves are open.
2. Using the unit control, set leaving-fluid set point (Cooling Setpoint 1, CSP.1). No cooling range adjustment is
necessary.
3. If optional control functions or accessories are being
used, the unit must be properly configured. Refer to
Configuration Options section for details.
4. Start the chilled fluid pump, if unit is not configured for
pump control. (Cooler Pumps Sequence, PUMP=0)
5. Complete the Start-Up Checklist to verify all components
are operating properly.
6. If unit is equipped with navitgator turn Enable/Off/Remote
contact switch to Enable position. If unit is equipped with
Touch Pilot press the Start/Stop button and select Local On.
7. Allow unit to operate and confirm that everything is
functioning properly. Check to see that leaving fluid
temperature agrees with leaving set point Control Point
(Control Point, CTPT).
59
1. Determine average voltage:
Operating Limitations
TEMPERATURES — Unit operating temperature limits are
listed in the table below.
TEMPERATURE
Maximum Ambient Temperature
Minimum Ambient Temperature
Maximum Cooler EWT*
Maximum Cooler LWT
Minimum Cooler LWT†
F
125
32
95
60
40
Average voltage =
C
52
0
35
15
4.4
=
=
2. Determine maximum deviation from average voltage:
(AB) 243 – 239 = 4 v
(BC) 239 – 236 = 3 v
(AC) 239 – 238 = 1 v
Maximum deviation is 4 v.
3. Determine percent voltage imbalance:
LEGEND
EWT — Entering Fluid (Water) Temperature
LWT — Leaving Fluid (Water) Temperature
*For sustained operation, EWT should not exceed 70 F (21.1 C).
†Unit requires brine modification for operation below this
temperature.
% Voltage Imbalance = 100 x
Low Ambient Temperature Operation — If unit operating
temperatures below 32 F (0° C) are expected, refer to separate
unit installation instructions for low ambient temperature operation using accessory low ambient temperature head pressure
control, if not equipped. Contact your Carrier representative for
details.
NOTE: If wind velocity is expected to be greater than 5 mph
(8 km/h) wind baffles and brackets must be field-fabricated
and installed for all units using accessory low ambient head
pressure control. See the 30XA Installation Instructions or the
low ambient temperature head pressure control accessory
installation instructions for more information.
4
239
= 1.7%
This voltage imbalance is satisfactory as it is below the
maximum allowable of 2%.
IMPORTANT: If the supply voltage phase imbalance is more than 2%, contact the local electric
utility company immediately. Do not operate unit
until imbalance condition is corrected.
MINIMUM FLUID LOOP VOLUME — To obtain proper
temperature control, loop fluid volume must be at least 3 gallons per ton (3.25 L per kW) of chiller nominal capacity for air
conditioning and at least 6 gallons per ton (6.5 L per kW) for
process applications or systems that must operate at low ambient temperatures (below 32 F [0° C]). Refer to application information in Product Data literature for details.
FLOW RATE REQUIREMENTS — Standard chillers should
be applied with nominal flow rates within those listed in the
Minimum and Maximum Cooler Flow Rates table. Higher or
lower flow rates are permissible to obtain lower or higher
temperature rises. Minimum flow rates must be exceeded to
assure turbulent flow and proper heat transfer in the cooler. See
Table 44. See Fig. 38A-38D for cooler pressure drop curves.
CAUTION
Brine duty application (below 40 F [4.4 C] LCWT) for
chiller normally requires factory modification. Contact a
Carrier Representative for details regarding specific
applications. Operation below 40 F (4.4 C) LCWT without modification can result in compressor failure.
VOLTAGE
Main Power Supply — Minimum and maximum acceptable
supply voltages are listed in the Installation Instructions.
Unbalanced 3-Phase Supply Voltage — Never operate a motor
where a phase imbalance between phases is greater than 2%.
To determine percent voltage imbalance:
% Voltage Imbalance = 100 x
243+236+238
3
717
3
239
CAUTION
Operation below minimum flow rate could generate
alarms, which could result in damage to the cooler.
max voltage deviation from
avg voltage
Consult application data section in the Product Data
literature and job design requirements to determine flow rate
requirements for a particular installation.
average voltage
The maximum voltage deviation is the largest difference
between a voltage measurement across 2 legs and the average
across all 3 legs.
Example: Supply voltage is 240-3-60.
AB = 243v
BC = 236v
AC = 238v
60
Table 44 — 30XA Minimum and Maximum Cooler Flow Rates
30XA
UNIT SIZE
80
82
90
92
100
102
110
112
120
122
140
142
160
162
180
182
200
202
220
222
240
242
260
262
280
282
300
302
325
327
350
352
400
450
500
DX
ITEM
Cooler Leaving Water Temperature*
Cooler Entering Water Temperature†
Nominal Flow Rate
Cooler
(gpm)
(L/s)
Standard, Flooded
180.4
11.4
Plus One Pass, Flooded
Minus One Pass, Flooded
172.8
10.9
DX Cooler
Standard, Flooded
201.9
12.7
Plus One Pass, Flooded
Minus One Pass, Flooded
193.7
12.2
DX Cooler
Standard, Flooded
225.5
14.2
Plus One Pass, Flooded
Minus One Pass, Flooded
214.3
13.5
DX Cooler
Standard, Flooded
244.9
15.5
Plus One Pass, Flooded
Minus One Pass, Flooded
235.2
14.8
DX Cooler
Standard, Flooded
264.8
16.7
Plus One Pass, Flooded
Minus One Pass, Flooded
254.7
16.0
DX Cooler
Standard, Flooded
317.8
20.1
Plus One Pass, Flooded
Minus One Pass, Flooded
303.5
19.1
DX Cooler
Standard, Flooded
365.1
23
Plus One Pass, Flooded
Minus One Pass, Flooded
347
21.9
DX Cooler
Standard, Flooded
409.6
25.8
Plus One Pass, Flooded
Minus One Pass, Flooded
401.7
25.3
DX Cooler
Standard, Flooded
463.9
29.3
Plus One Pass, Flooded
Minus One Pass, Flooded
447.1
28.2
DX Cooler
Standard, Flooded
505.9
31.9
Plus One Pass, Flooded
Minus One Pass, Flooded
493
31.1
DX Cooler
Standard, Flooded
545.8
34.4
Plus One Pass, Flooded
Minus One Pass, Flooded
530
33.5
DX Cooler
Standard, Flooded
600.3
37.9
Plus One Pass, Flooded
Minus One Pass, Flooded
583
36.8
DX Cooler
Standard, Flooded
Plus One Pass, Flooded
642.2
40.5
Minus One Pass, Flooded
627
39.5
DX Cooler
Standard, Flooded
687.5
43.4
Plus One Pass, Flooded
Minus One Pass, Flooded
665
42.0
DX Cooler
Standard, Flooded
733.4
46.3
Plus One Pass, Flooded
Minus One Pass, Flooded
720
45.4
DX Cooler
Standard, Flooded
775.4
48.9
Plus One Pass, Flooded
Minus One Pass, Flooded
757
47.8
DX Cooler
Standard, Flooded
917.6
57.9
Plus One Pass, Flooded
Minus One Pass, Flooded
Standard, Flooded
1019.3
64.3
Plus One Pass, Flooded
Minus One Pass, Flooded
Standard, Flooded
1092.8
68.9
Plus One Pass, Flooded
Minus One Pass, Flooded
MINIMUM
40 F (4.4 C)
45 F (7.2 C)
Minimum Flow Rate
(gpm)
(L/s)
95
6
43
2.7
196
12.4
86
5.4
101
6.4
43
2.7
229
14.4
97
6.1
101
6.4
43
2.7
229
14.4
107
6.7
125
7.9
61
3.8
254
16
118
7.4
125
7.9
73
4.6
281
17.7
127
8.0
134
8.5
73
4.6
324
20.4
152
9.6
165
10.4
98
6.2
354
22.3
174
10.9
202
12.7
73
4.6
416
26.2
201
12.6
223
14.1
98
6.2
458
28.9
224
14.1
235
14.8
122
7.7
501
31.6
246
15.5
266
16.8
147
9.3
538
33.9
265
16.7
257
16.2
141
8.9
584
36.8
292
18.4
293
18.5
141
8.9
620
39.1
313
19.8
327
20.6
174
11
687
43.3
333
21.0
361
22.8
211
13.3
724
45.7
360
22.7
379
23.9
244
15.4
767
48.4
379
23.9
501
31.6
—
—
—
—
501
31.6
—
—
—
—
501
31.6
—
—
—
—
MAXIMUM
60 F (15 C)
70 F (21.1 C)
Maximum Flow Rate
(gpm)
(L/s)
379
23.9
192
12.1
782
49.3
346
21.8
403
25.4
200
12.6
917
57.9
387
24.4
403
25.4
200
12.6
917
57.9
429
27.0
501
31.6
244
15.4
1014
64
470
29.6
501
31.6
293
18.5
1124
70.9
509
32.1
538
33.9
293
18.5
1296
81.8
607
38.2
660
41.6
391
24.7
1418
89.5
694
43.7
807
50.9
391
24.7
1662
104.9
803
50.6
892
56.3
391
24.7
1833
115.6
894
56.3
941
59.4
489
30.9
2004
126.4
950
59.9
1063
67.1
587
37
2151
135.7
950
59.9
1027
64.8
562
35.5
2334
147.3
950
59.9
1173
74
562
35.5
2481
156.5
950
59.9
1308
82.5
697
44
2750
173.5
1331
83.9
1442
91
843
53.2
2897
182.8
1440
90.8
1516
95.6
978
61.7
3068
193.6
1514
95.5
2004
126.4
—
—
—
—
2004
126.4
—
—
—
—
2004
126.4
—
—
—
—
Number of
Passes
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
2
3
1
—
1
—
—
1
—
—
1
—
—
NOTES:
1. The 30XA units will start and pull down with loop temperatures up to 95 F (35 C).
2. Nominal flow rates required at AHRI conditions 44 F (7 C) leaving fluid temperature, 54 F (12 C) entering water temperature, 95 F (35 C) ambient. Fouling factor
0.00010 ft2-hr-F/Btu (0.000018 m2-K/kW).
3. To obtain proper temperature control, cooler loop fluid volume must be at least
3 gal/ton (3.23 L/kW) of chiller nominal capacity for air conditioning and at least
6 gal/ton (6.5 L/kW) for process applications or systems that must operate in low
ambient temperatures (below 32 F [0° C]).
LEGEND
— Direct Expansion
*For applications requiring cooler leaving water temperature operation at less than
40 F (4.4 C), the units require the use of antifreeze and application may require
the brine option. Contact your local Carrier representative for more information.
†For applications requiring cooler entering water temperature operation at less
than 45 F (7.2 C), contact your local Carrier representative for unit selection using
the Carrier electronic catalog.
61
Unit Sizes 30XA080, 90, 100, 110, 120
50
(149.5)
080
45
(134.6)
090,100
110
120
Pressure Drop, ft wg (kPa)
40
(119.6)
35
(104.7)
30
(89.7)
25
(74.8)
20
(59.8)
15
(44.9)
10
(29.9)
5
(15)
0
0
100
(6.3)
200
(12.6)
300
(18.9)
400
(25.2)
500
(31.6)
Cooler Flow, GPM (l/s)
600
(37.9)
a30-4233
Unit Sizes 30XA140, 160, 180, 200, 220, 240
60
(179.4)
240
160
Pressure Drop, ft wg (kPa)
220
140
50
(149.5)
180 200
40
(119.6)
30
(89.7)
20
(59.8)
10
(29.9)
0
0
200
(12.6)
400
(25.2)
600
(37.9)
800
(50.5)
Cooler Flow, GPM (l/s)
1000
(63.1)
1200
(75.7)
1400
(88.3)
a30-4256
Fig. 38A — Cooler Pressure Drop Curves, Standard Pass Flooded Cooler
62
Unit Sizes 30XA260, 280, 300, 325, 350, 400, 450, 500
60
(179.4)
260 280
300
Pressure Drop, ft wg (kPa)
50
(149.5)
325 350
500
450
40
(119.6)
400
30
(89.7)
20
(59.8)
10
(29.9)
0
500
(31.6)
0
1000
(63.1)
1500
(94.6)
2000
(126.2)
2500
(157.7)
3000
(189.3)
a30-4257
Cooler Flow, GPM (l/s)
Fig. 38A — Cooler Pressure Drop Curves, Standard Pass Flooded Cooler (cont)
Unit Sizes 30XA082, 092, 102, 112, 122, 142, 162, 182, 202
70
(209.3)
Pressure Drop, ft wg (kPa)
60
(179.4)
082, 092, 102
50
(149.5)
40
(119.6)
112, 122
142, 162
182, 202
30
(89.7)
20
(59.8)
10
(29.9)
0
0
100
(6.31)
200
(12.62)
300
(18.93)
400
(25.24)
500
(31.55)
Cooler Flow, GPM (l/s)
600
(37.85)
700
(44.16)
800
(50.47)
a30-5308
Fig. 38B — Cooler Pressure Drop Curves, DX (Direct Expansion) Cooler
63
Unit Sizes 30XA222, 242, 262, 282, 302, 327, 352
80
Pressure Drop, wg (kPa)
(239.1)
60
(179.4)
222, 242
302, 327, 352
262, 282
40
(119.6)
20
(59.8)
0
0
200
(12.62)
400
(25.24)
600
(37.85)
800
(50.47)
1000
(63.09)
1200
(75.71)
1400
(88.32)
1600
(100.94)
1800
(113.56)
Cooler Flow, GPM (l/s)
Fig. 38B — Cooler Pressure Drop Curves, DX (Direct Expansion) Cooler (cont)
a30-5393
Unit Sizes 30XA080, 090, 100, 110, 120
250
(747)
Pressure Drop, ft wg (kPa)
200
(598)
080
090,100
110
150
(488)
120
100
(299)
50
(149)
0
0
100
(6.3)
200
(12.6)
300
(18.9)
400
(25.2)
500
(31.6)
Cooler Flow, GPM (l/s)
Fig. 38C — Cooler Pressure Drop Curves, Plus One-Pass Flooded Cooler
64
600
(37.9)
a30-4486
Unit Sizes 30XA140, 160, 180, 200, 220, 240
250
(747)
180
200
(598)
200
Pressure Drop, ft wg (kPa)
220
140
240
160
150
(488)
100
(299)
50
(149)
0
0
200
(12.6)
400
(25.2)
600
(37.9)
a30-4487
800
(50.6)
1000
(63.3)
1200
(75.9)
1400
(88.6)
COOLER FLOW, GPM (l/s)
Unit Sizes 30XA260, 280, 300, 325, 350
250
(747)
280
200
(598)
260
Pressure Drop, ft wg (kPa)
300
325
350
150
(488)
100
(299)
50
(149)
0
0
a30-4489
200
(12.6)
400
(25.2)
600
(37.9)
800
(50.6)
1000
(63.3)
1200
(75.9)
1400
(88.6)
1600
(101.3)
COOLER FLOW, GPM (l/s)
NOTE: Plus-one-pass coolers are not available for 30XA400-500 units.
Fig. 38C — Cooler Pressure Drop Curves, Plus One-Pass Flooded Cooler (cont)
65
1800
(114.0)
Unit Sizes 30XA080, 090, 100, 110, 120, 140
10
(29.9)
9
(26.1)
140
Pressure Drop, ft wg (kPa)
8
(23.2)
080
110
090,100
120
7
(20.3)
6
(17.4)
5
(14.5)
4
(11.6)
3
(8.7)
2
(5.8)
1
(2.9)
0
0
100
(6.3)
200
(12.6)
300
(18.9)
400
(25.2)
500
(31.6)
600
(37.9)
700
(44.2)
COOLER FLOW, GPM (l/s)
a30-4490
Unit Sizes 30XA140, 160, 180, 200, 220, 240
12
(35.7)
160
10
(29.9)
140
Pressure Drop, ft wg (kPa)
240
220
8
(23.2)
200
180
6
(17.4)
4
(11.6)
2
(5.3)
0
0
200
(12.6)
400
(25.2)
600
(37.9)
800
(50.6)
1000
(63.3)
1200
(75.9)
COOLER FLOW, GPM (l/s)
NOTE: Minus-one-pass coolers are not available for 30XA400-500 units.
Fig. 38D — Cooler Pressure Drop Curves, Minus One-Pass Flooded Cooler
66
1400
(88.6)
a30-4491
Unit Sizes 30XA260, 280, 300, 325, 350
10
(29.9)
350
325
280
9
(26.1)
300
260
8
(23.2)
Pressure Drop, ft wg (kPa)
7
(20.3)
6
(17.4)
5
(14.5)
4
(11.6)
3
(8.7)
2
(5.5)
1
(2.9)
0
0
200
(12.6)
400
(25.2)
600
(37.9)
800
(50.6)
1000
(63.3)
1200
(75.9)
1400
(88.6)
1600
(101.3)
1800
(114.0)
a30-4492
COOLER FLOW, GPM (l/s)
NOTE: Minus-one-pass coolers are not available for 30XA400-500 units.
Fig. 38D — Cooler Pressure Drop Curves, Minus One-Pass Flooded Cooler (cont)
the valve will close immediately without waiting for pressure
equalization.
The actuated ball valves are linked to the cooler heater operation in the controls. Cooler Heater option (Configuration 
Unit CO.HT , SERVICE FACTORY Cooler Heater
Select) must be enabled for the Actuated Ball Valve to operate.
See Fig. 40 for a view of a fully open ball valve with the actuator removed. The flat surface at the top of the valve shaft is
parallel to the discharge line. The ball valve motor mounting
plate should be perpendicular to the discharge line at all times.
If not, adjust it by loosening the set screw on the side of the
valve, reposition assembly and tighten set screw.
See Fig. 41 for a view of the ball valve motor mounting
with a fully open valve. The motor actuator arm should be at a
counterclockwise position, with the valve shaft in a parallel position. If not in a parallel position, loosen the clamping screw
and push the disengagement button to rotate the actuator arm
until it stops. Retighten the clamping screw.
ABV Manual Operation — The ABV can be operated manually as a discharge service valve by completing the following
steps:
1. Remove the actuator cover.
2. With the compressor off hold down the Push button.
3. Close the ABV by turning the shaft adapter by hand or
with a wrench so that the flats on the end of the shaft are
perpendicular to the discharge line.
4. Release the Push button.
5. Disconnect the control power cable to the ABV.
OPERATION
Sequence of Operation — With a command to start
the chiller, the cooler pump will start. After verifying water
flow, the control will monitor the entering and leaving water
temperature. If the need for mechanical cooling is determined,
the control decides which circuit and compressor to start. The
control will start the required compressor completely unloaded
and deenergize the oil separator heater (if already energized).
The control will continue to load this circuit by moving the
slide valve to satisfy cooling requirements. Once fully loaded,
the control will start additional circuits to satisfy the load as
required. Shutdown of each circuit under normal conditions
occurs in the opposite sequence to loading. Once the A circuit
is fully unloaded the compressor is shut off and the EXV will
close completely.
If the outside-air temperature is less than the brine freeze
point plus 17º F (9.4º C) then the circuit will perform a pump
down cycle. The EXV will be closed and the compressor continues to operate until the saturated suction temperature (SST)
is 10º F (5.6º C) lower than the starting SST or 10º F (5.6º C)
less than the brine freeze point. Once the compressor is shut off
the actuated ball valve (located in the discharge line) will be
closed if equipped (flooded cooler option units only).
ACTUATED BALL VALVE (ABV), FLOODED COOLER
ONLY — There is either one or two discharge ABVs located
in the discharge line of each circuit of the unit. See Fig. 39 for a
typical ABV assembly with enclosure. The ABV is a motorized ball valve, which is used to close the discharge line to prevent refrigerant migrating from condenser to the cooler when
the circuit is off. The valve will be opened before the compressor is started and will normally close when pressure equalizes
between suction and discharge lines. If the outside air temperature is less than the brine freeze point plus 17º F (9.4º C) then
67
Dual Chiller Sequence of Operation — With a com-
mand to start the chiller, the master chiller determines which
chiller will become the lead chiller based on the configuration
of Lead Lag Select, LLBL and Lead/Lag Balance Data,
LLBD. The lead chiller is always started first and the lag chiller
is held at zero percent capacity by the master chiller forcing the
lag demand limit value to 0%. If Lead Pulldown Time (Lead
Pulldown Time, LPUL) has been configured, the lead chiller
will continue to operate alone for that specified time. After the
Lead Pulldown Time timer has elapsed and when the lead chiller is fully loaded, either all available compression is on or at the
master demand limit value, then the lag start timer (Lag Start
Timer, LLDY) is initiated. When the pulldown timer and lag
start timer has elapsed and the Combined Leaving Chilled Water Temperature is more than 3° F (1.7° C) above the set point,
then the lag chiller is started. If the lag chiller’s water pump
was not started when the machines went into occupied mode,
the lag chiller water pump will be started. The lag chiller will
start with the master chiller forcing the lag chiller demand limit
value (LAG_LIM) to the master’s demand limit value. If lead/
lag capacity balance is selected, once the lag chiller has started,
the master shall try to keep the difference in capacity between
lead and lag less than 20%. The master shall then be responsible for water loop capacity calculation, and will determine
which chiller, the lead or lag, will increase or decrease capacity.
When the load reduces, the lag chiller will be the first chiller to
unload. To accomplish this, the lead chiller set point is decreased by 4° F (–2.2° C) until the lag chiller unloads.
PUMP OPERATION — For parallel chiller pump operation,
the lead chiller’s water pump will be started. The lag chiller’s
water pump will be maintained off if Lag Unit Pump Control,
LAGP=0. The internal algorithm of lead chiller will control capacity of the lead chiller.
For series chiller operation, the pump is always controlled
by the master chiller.
VALVE MOTOR COVER
VALVE MOTOR
BASE PLATE
a30-4236
Fig. 39 — Typical ABV Assembly with Enclosure
VALVE SHAFT
Operating Modes — Operating modes are override
modes that affect normal operation of the equipment. More
than one operating mode can be in effect at the same time.
Some operating modes have corresponding capacity control
overrides in the Capacity Control Overrides section on
page 47.
For the Touch Pilot™ display, the status of the operating
modes can be found in the MODES submenu, which is under
the STATUS menu. Each operating mode and its status (Yes =
active, No = inactive) is listed.
For the Navigator™ display, the status of the operating
modes can be found in the MODE submenu under the OPERATING MODES menu. The 6 top priority operating modes are
displayed in MD01 through MD06. To view the modes with
the Navigator display:
a30-4237
Fig. 40 — Fully Open Ball Valve
with Actuator Removed
ITEM
MD01
MD02
MD03
MD04
MD05
MD06
MOUNTING - FULLY CLOSED
DISENGAGEMENT
BUTTON
ACTUATOR ARM
PATH
Operating modesMODE
Operating modesMODE
Operating modesMODE
Operating modesMODE
Operating modesMODE
Operating modesMODE
VALUE
0-32
0-32
0-32
0-32
0-32
0-32
See Table 45 for a list of operating modes.
STARTUP DELAY IN EFFECT — This mode is checked
for when the unit is started. This mode is active when the Minutes Off Time (Unit Off to On Delay, DELY) timer is active.
The unit will not start until the timer has expired. The mode
will terminate when the timer expires.
CLAMPING SCREW
MOUNTING - FULLY OPEN
ITEM EXPANSION
First Active Mode
Second Active Mode
Third Active Mode
Fourth Active Mode
Fifth Active Mode
Sixth Active Mode
a30-4238
Fig. 41 — Ball Valve Motor
68
Table 45 — 30XA Operating Modes
NAVIGATOR OPERATING
MODE NUMBER
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
NAVIGATOR EXPANSION
Startup Delay in Effect
Second Setpoint in Use
Reset in Effect
Demand Limit Active
Ramp Loading Active
Cooler Heater Active
Cooler Pumps Rotation
Pump Periodic Start
Night Low Noise Active
System Manager Active
Mast Slave Ctrl Active
Auto Changeover Active
Free Cooling Active
Reclaim Active
Electric Heat Active
Heating Low EWT Lockout
Condenser Pumps Rotation
Ice Mode in Effect
Defrost Active on Cir A
Defrost Active on Cir B
Low Suction Circuit A
Low Suction Circuit B
Low Suction Circuit C
High DGT Circuit A
High DGT Circuit B
High DGT Circuit C
High Pres Override Cir A
High Pres Override Cir B
High Pres Override Cir C
Low Superheat Circuit A
Low Superheat Circuit B
Low Superheat Circuit C
TOUCH PILOT DISCRIPTION
Startup Delay in Effect
Second Setpoint in Use
Reset in Effect
Demand Limit Active
Ramp Loading Active
Cooler Heater Active
Cooler Pumps Rotation
Pump Periodic Start
Night Low Noise Active
System Manager Active
Mast Slave Active
Auto Changeover Active
Free Cooling Active
Reclaim Active
Electric Heat Active
Heating Low EWT Lockout
Condenser Pumps Rotation
Ice Mode in Effect
Defrost Active on Cir A
Defrost Active on Cir B
Low Suction Circuit A
Low Suction Circuit B
Low Suction Circuit C
High DGT Circuit A
High DGT Circuit B
High DGT Circuit C
High Pres Override Cir A
High Pres Override Cir B
High Pres Override Cir C
Low Superheat Circuit A
Low Superheat Circuit B
Low Superheat Circuit C
TOUCH PILOT
LINE NUMBER
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
TOUCH PILOT
VALUE
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
(Ramp Loading Select, RL.S) is enabled and the following
conditions are met:
1. The leaving water temperature is more than 4° F (2.2° C)
from the Control Point (Control Point, CTPT), and
2. The rate of change of the leaving water temperature is
greater than the Cool Ramp Loading (Cooling Ramp
Loading, CRMP).
The control will limit the percent capacity increase until one
of the two conditions above are no longer met, then the mode
will terminate.
COOLER HEATER ACTIVE — This mode is checked for
whether the unit is ON or OFF. The mode is active when the
cooler heater is energized. The cooler heater is energized when
the Outdoor Air Temperature (External Temperature, OAT)
is less than the calculated value, (Freeze Setpoint + Cooler
Heater Delta T Setpoint [Cooler Heater Delta Spt, HTR] default – 2° F [1.1° C]) and either the Leaving Water Temperature
(Cooler Leaving Fluid, LWT) or the Entering Water Temperature (Cooler Entering Fluid, EWT) are less than or equal to
the Freeze Setpoint + Cooler Heater Delta T Setpoint (HTR).
The Freeze Setpoint is 34 F (1.1 C), for fresh water systems
(Cooler Fluid Type, FLUD=1). The Freeze Setpoint is Brine
Freeze Setpoint (Brine Freeze Setpoint, LOSP), for Medium
Temperature Brine systems (Cooler Fluid Type, FLUD=2).
When in this mode, the cooler heater will be energized. The
cooler heater will be deenergized when both the Entering Water Temperature (EWT) and Leaving Water Temperature
(LWT) are above the Freeze Setpoint + Cooler Heater Delta T
Setpoint (HTR).
This mode is enabled for freeze protection. If the temperatures are not as described above, check the accuracy of the outside air, entering and leaving water thermistors.
COOLER PUMPS ROTATION — This mode is checked for
whether the unit is ON or OFF. The mode is active when the
SECOND SETPOINT IN USE — This mode is checked for
when the unit is ON. The mode is active when Cooling Setpoint 2 (Cooling Setpoint 2, CSP.2) or Ice Setpoint (Cooling
Ice Setpoint, CSP.3) is in use. While in this mode, the Active
Setpoint (Current Setpoint, SETP) will show the CSP.2 or
CSP.3 value.
While in this mode, the unit will operate to the Cooling Setpoint 2 (CSP.2) or Ice Setpoint (CSP.3). The mode will terminate when the Cooling Setpoint 2 (CSP.2) or Ice Setpoint
(CSP.3) is no longer in use.
RESET IN EFFECT — This mode is checked for when the
unit is ON. The mode will be active when Temperature Reset
(Cooling Reset Select, CRST) is enabled either by CRST=1
(Outside Air Temperature), CRST=2 (Return Water), CRST=3
(4-20 mA Input), or CRST=4 (Space Temperature) and reset is
active.
While in this mode, the Active Setpoint (Current Setpoint,
SETP) will be modified according to the programmed information and will be displayed as the Control Point (Control
Point, CTPT). The mode will terminate when the Temperature
Reset is not modifying the active leaving water set point, causing SETP to be the same as CTPT.
DEMAND LIMIT ACTIVE — This mode is chacked for
when the unit is ON. The mode is active when Demand Limit
(Demand Limit Type Select, DMDC) is enabled either by
DMDC=1 (Switch), DMDC=2 (4-20 mA Input), or the Night
Time Low Sound Capacity Limit (Capacity Limit, LS.LT).
The Active Demand Limit Value (Active Demand Limit
Val, LIM) will display the current demand limit according to
the programmed information and the unit’s capacity will be reduced to the amount shown or lower. The mode will terminate
when the Demand Limit command has been removed.
RAMP LOADING ACTIVE — This mode is checked for
when the unit is ON. The mode is active when Ramp Loading
69
Setpoint (CSP.3). This mode will terminate when the Ice
Setpoint (CSP.3) is no longer in use.
DEFROST ACTIVE ON CIR A — This mode is not
supported.
DEFROST ACTIVE ON CIR B — This mode is not
supported.
LOW SUCTION CIRCUIT A
LOW SUCTION CIRCUIT B
LOW SUCTION CIRCUIT C — These modes are checked
when the circuit is ON. The appropriate circuit mode will be
active if one of the following conditions is true:
1. If the circuit’s saturated suction temperature (SST) is
more than 6° F (3.3° C) less than the freeze point and
both the cooler approach (Leaving Water Temperature –
SST) and superheat (Suction Gas Temperature – SST) are
greater than 15° F (8.3° C).
2. If the circuit is ON and the circuit’s SST is more than
18º F (10.0º C) below the freeze point for more than
90 seconds.
3. If the circuit’s saturated suction temperature is more
than 6° F (3.3° C) below the freeze point for more than
3 minutes.
For a fresh water system (Cooler Fluid Type, FLUD =1),
the freeze point is 34° F (1.1° C). For medium temperature
brine systems, (Cooler Fluid Type, FLUD=2), the freeze point
is Brine Freeze Set Point (Brine Freeze Setpoint, LOSP).
For criterion 1, no additional capacity will be added. For criteria 2 and 3 capacity will be decreased on the circuit. The
mode will terminate when the circuit’s SST is greater than the
freeze point minus 6° F (3.3° C) or the circuit has alarmed.
If this condition is encountered, see Possible Causes for
Alarms 56-58 on page 98.
HIGH DGT CIRCUIT A — This mode is not supported.
HIGH DGT CIRCUIT B — This mode is not supported.
HIGH DGT CIRCUIT C — This mode is not supported.
HIGH PRES OVERRIDE CIR A
HIGH PRES OVERRIDE CIR B
HIGH PRES OVERRIDE CIR C — This mode is checked
for when the circuit is ON. The appropriate circuit mode will
be active if the discharge pressure for the circuit, Discharge
Pressure Circuit A (Discharge Pressure, DP.A), Discharge
Pressure Circuit B (Discharge Pressure, DP.B), or Discharge
Pressure Circuit C (Discharge Pressure, DP.C), is greater than
the High Pressure Threshold (High Pressure Threshold,
HP.TH).
The capacity of the affected circuit will be reduced. Two
minutes following the capacity reduction, the circuit’s saturated
condensing temperature (SCTt+2) is calculated and stored. The
affected circuit will not be allowed to add capacity for at least 5
minutes following the capacity reduction. If after 5 minutes,
the circuit’s saturated condensing temperature is less than
SCTt+2 –3° F (1.7° C), and then if required, percent capacity
will be added. If additional capacity is required, the control will
look for other circuits to add capacity.
This mode will terminate once the circuit’s saturated condensing temperature is less than SCTt+2 –3° F (1.7° C).
If this condition is encountered, see Possible Causes for
Alarm A1.03. on page 103.
LOW SUPERHEAT CIRCUIT A
LOW SUPERHEAT CIRCUIT B
LOW SUPERHEAT CIRCUIT C — This mode is checked
for when the circuit is ON. The appropriate circuit mode will
be active if the circuit’s superheat (discharge gas temperature –
SCT) is less than 18° F (10° C).
Cooler Pump Sequence (Cooler Pump Run Status,
PUMP=2) (2 Pumps Automatic Changeover) and the Pump
Rotation Delta Timer (Pump Auto Rotation Delay, ROT.P)
have expired.
The control will switch the operation of the pumps. The
lead pump will operate normally. The lag pump will be started,
becoming the lead, and then the original lead pump will be shut
down. This mode will terminate when the pump operation has
been completed.
PUMP PERIODIC START — This mode is active when the
cooler pump is started due to the Periodic Pump Start configuration (Pump Sticking Protection, PM.PS=YES). If the pump
has not run that day, a pump will be started and will run for 2
seconds at 2:00 PM. If the machine is equipped with dual
pumps, Pump no. 1 will run on even days (such as day 2, 4, 6
of the month). Pump no. 2 will run on odd days (such as day 1,
3, 5 of the month). The mode will terminate when the pump
shuts down.
NIGHT LOW NOISE ACTIVE — This mode is active when
the Night Time Low Noise Option has been configured and the
current time is within the configured time frame. Programming
a Night Low Noise Start Time (Start Hour, LS.ST) and a
Night Low Noise End Time (End Hour, LS.ND) configures
the option.
The control will raise the head pressure set point to reduce
the number of condenser fans on, thereby reducing the sound
level of the machine. Additionally, if the Night Time Low
Sound Capacity Limit (Start Hour, LS.LT) has been configured, the unit’s capacity will be limited to the programmed level. This mode will terminate once the Night Low Noise End
Time (LS.ND) has been reached.
SYSTEM MANAGER ACTIVE — This mode is checked
when the unit is ON or OFF. This mode is active if a System
Manager such as Building Supervisor, Chillervisor System
Manager, or another CCN device is controlling the machine.
When this mode is active, the machine will respond to the
specific commands received from the System Manager. The
mode will be terminated if the System Manager control is released.
MASTER SLAVE CONTROL ACTIVE — This mode is
checked for if the machine is ON. This mode is active if Master
Slave Control has been enabled. This occurs when two machines are programmed, one as the master (Master/Slave Select, MSSL=1 [Master]) and the other as a slave (Master/
Slave Select, MSSL=2 [Slave]).
Both the master and slave machines will respond to the capacity control commands issued by the master controller. This
may include control point changes and demand limit commands. This mode will terminate when Master Slave Control
has been disabled.
AUTO CHANGEOVER ACTIVE — This mode is not
supported.
FREE COOLING ACTIVE — This mode is not supported.
RECLAIM ACTIVE — This mode is not supported.
ELECTRIC HEAT ACTIVE — This mode is not supported.
HEATING LOW EWT LOCKOUT — This mode is not
supported.
CONDENSER PUMPS ROTATION — This mode is not
supported.
ICE MODE IN EFFECT — This mode is checked for when
the unit is ON. This mode is active when Ice Setpoint (Cooling
Ice Setpoint, CSP.3) is in use. While in this mode, the Active
Setpoint (Current Setpoint, SETP) will show the Cooling Ice
Setpoint, CSP.3, value and the unit will operate to the Ice
70
the conditioned space where it will not be subjected to either a
cooling or heating source or direct exposure to sunlight, and 4
to 5 ft above the floor).
Space temperature sensor wires are to be connected to
terminals in the unit main control box. See Fig. 44. The space
temperature sensor includes a terminal block (SEN) and a RJ11
female connector. The RJ11 connector is used access into
the Carrier Comfort Network® (CCN) at the sensor.
To connect the space temperature sensor (see Fig. 44):
1. Using a 20 AWG twisted pair conductor cable rated for
the application, connect one wire of the twisted pair to
one SEN terminal and connect the other wire to the other
SEN terminal located under the cover of the space
temperature sensor.
2. Connect the other ends of the wires to terminals 7 and 8
on TB6 located in the unit control box.
Units on the CCN can be monitored from the space at the
sensor through the RJ11 connector, if desired. To wire the RJ11
connector into the CCN:
1. Cut the CCN wire and strip ends of the red (+), white
(ground), and black (–) conductors. (If another wire color
scheme is used, strip ends of appropriate wires.)
2. Insert and secure the red (+) wire to terminal 5 of the
space temperature sensor terminal block.
3. Insert and secure the white (ground) wire to terminal 4 of
the space temperature sensor.
4. Insert and secure the black (–) wire to terminal 2 of the
space temperature sensor.
No additional capacity will be added until the circuit’s superheat is greater than 18° F (10° C). The control will look for
other circuits to add capacity if additional steps of capacity are
required. This mode will terminate once the affected circuit’s
superheat is greater than 18° F (10° C).
If this condition is encountered, see Possible Causes for
Alarms P.11, P.12 and P.13 on page 98.
Sensors — The electronic control uses up to 17 thermistors
to sense temperatures and up to 12 transducers to sense
pressure for controlling chiller operation. These sensors are
outlined below.
THERMISTORS (Tables 46-47B) — Thermistors that are
monitoring the chiller’s operation include: Cooler Entering
Water, Cooler Leaving Water, Dual Chiller Leaving Water,
Compressor Suction Gas Temperature, Compressor Discharge
Gas Temperature, Economizer Temperature, Compressor Motor
Temperature, and Outdoor Air Temperature Thermistors. These
thermistors are 5 kat 77 F (25 C) and are identical in temperature versus resistance. The Space Temperature Thermistor is
10 k at 77 F (25 C) and has a different temperature vs.
resistance.
Cooler Leaving Water Sensor — On all sizes, this thermistor
is installed in a friction fit well in the leaving water nozzle of
the cooler. See Fig. 42 and 43.
Cooler Entering Water Sensor — On all sizes, this thermistor
is factory-installed in a friction fit well in the entering water
nozzle of the cooler.
Suction Gas Temperature — On all sizes, this thermistor is
factory-installed in a friction fit well located on the compressor
of each circuit. There is one thermistor for each circuit.
Compressor Discharge Gas Temperature — On all sizes, this
thermistor is factory-installed in a friction fit well located in the
discharge end of the compressor for the circuit. There is one
thermistor for each circuit.
Economizer Temperature — On all sizes except 080 and 082,
this thermistor is factory-installed in a friction fit well located
in the economizer line for the circuit. There is one thermistor
for each circuit.
Compressor Motor Temperature — On all sizes, this thermistor is embedded in the motor windings. There are two thermistors in each compressor. One spare is provided.
Outdoor Air Temperature — This sensor is factory-installed
to the back of the control box.
Remote Space Temperature — This sensor (part no.
33ZCT55SPT) is a field-installed accessory mounted in the indoor space and is used for water temperature reset. The sensor
should be installed as a wall-mounted thermostat would be (in
IMPORTANT: The cable selected for the RJ11
connector wiring MUST be identical to the CCN
communication bus wire used for the entire network.
Refer to Table 14 for acceptable wiring.
5. Connect the other end of the communication bus cable to
the remainder of the CCN communication bus.
NOTE: The Energy Management Module (EMM) is required
for this accessory.
TRANSDUCERS — There are four pressure transducers per
circuit, and two different types of transducers: low pressure
(green connector) and high pressure (black connector).
Low Pressure Type: Suction Pressure Transducer (SPT), Economizer Pressure Transducer (EPT).
High Pressure Type: Discharge Pressure Transducer (DPT),
Oil Pressure Transducer (OPT). See Fig. 45A and 45B for
transducer locations.
Table 46 — Thermistor Identification
THERMISTOR ID
DESCRIPTION
EWT
Entering Water Thermistor
LWT
Leaving Water Thermistor
OAT
Outdoor Air Thermistor
SGTA*
Circuit A Suction Gas Thermistor
SGTB*
Circuit B Suction Gas Thermistor
SGTC
Circuit C Suction Gas Thermistor
DGTA
Circuit A Discharge Gas Thermistor
DGTB
Circuit B Discharge Gas Thermistor
DGTC
Circuit C Discharge Gas Thermistor
ECTA
Circuit A Economizer Thermistor
ECTB
Circuit B Economizer Thermistor
ECTB
Circuit C Economizer Thermistor
DUAL
Dual Chiller LWT Thermistor
CAMT
Circuit A Motor Temperature
CBMT
Circuit B Motor Temperature
CCMT
Circuit C Motor Temperature
SPT
Space Temperature Thermistor
*SGTA and SGTB for 30XA080,082 units are connected to the EXVA board.
RESISTANCE AT 77 F (25 C)
5k 
5k 
5k 
5k 
5k 
5k 
5k 
5k 
5k 
5k 
5k 
5k 
5k 
5k 
5k 
5k 
10k 
71
CONNECTION POINT
MBB-J6-CH2
MBB-J6-CH1
MBB-J6-CH4
EXVA-J3-THA
EXVB-J3-THA
EXVC-J3-THA
CPM-A-J9-CH02
CPM-B-J9-CH02
CPM-C-J9-CH02
EXVA-J3-THB
EXVB-J3-THB
EXVC-J3-THB
MBB-J6-CH3
CPM-A-J9-CH01
CPM-B-J9-CH01
CPM-C-J9-CH01
EMM-J6-CH2
O-RING
BRASS NUT 3/8 - 24 FOR
ASSEMBLY ON BRASS WELL a30-4079
Fig. 42 — 5K Thermistor (Sensor 00PPG000008105A, Connector: HY06AM016)
1/4-18 NPT
a30-4080
SENSOR
a30-4081
TB6
SEN
SEN
7
6" MINIMUM
CLEARANCE FOR
THERMISTOR
REMOVAL
1.188 in.
8
2.315 in.
Fig. 43 — Dual Leaving Water Thermistor Well
(00PPG000008000A)
SUCTION PRESSURE
TRANSDUCER (SPT A)
Fig. 44 — Typical Remote Space Temperature
Sensor (33ZCT55SPT) Wiring
ECONOMIZER PRESSURE
TRANSDUCER (EPT A)
ECONOMIZER PRESSURE
TRANSDUCER (EPT B)
SUCTION PRESSURE
TRANSDUCER (SPT B)
COOLER
A
OIL SEPARATOR
B
DISCHARGE PRESSURE
TRANSDUCER (DPT A)
DISCHARGE PRESSURE
TRANSDUCER (DPT B)
CIRCUIT A
CIRCUIT B
OIL PRESSURE TRANSDUCER
(OPT B)
OIL PRESSURE TRANSDUCER
(OPT A)
Fig. 45A — Transducer Locations (Flooded Cooler Units)
72
COMPRESSOR
a30-4467
SUCTION PRESSURE
TRANSDUCER (SPT A)
ECONOMIZER PRESSURE
TRANSDUCER (EPT A)
ECONOMIZER PRESSURE
TRANSDUCER (EPT B)
SUCTION PRESSURE
TRANSDUCER (SPT B)
COOLER
A
OIL SEPARATOR
B
DISCHARGE PRESSURE
TRANSDUCER (DPT A)
DISCHARGE PRESSURE
TRANSDUCER (DPT B)
CIRCUIT A
CIRCUIT B
OIL PRESSURE TRANSDUCER
(OPT B)
OIL PRESSURE TRANSDUCER
(OPT A)
COMPRESSOR
a30-5329
Fig. 45B — Transducer Locations (DX Cooler Units)
Table 47A — 5K Thermistor Temperature (°F) vs Resistance
TEMP
(F)
–25
–24
–23
–22
–21
–20
–19
–18
–17
–16
–15
–14
–13
–12
–11
–10
–9
–8
–7
–6
–5
–4
–3
–2
–1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
RESISTANCE
(Ohms)
98,010
94,707
91,522
88,449
85,486
82,627
79,871
77,212
74,648
72,175
69,790
67,490
65,272
63,133
61,070
59,081
57,162
55,311
53,526
51,804
50,143
48,541
46,996
45,505
44,066
42,679
41,339
40,047
38,800
37,596
36,435
35,313
34,231
33,185
32,176
31,202
30,260
29,351
28,473
27,624
26,804
26,011
25,245
24,505
23,789
23,096
22,427
21,779
21,153
20,547
19,960
TEMP
(F)
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
RESISTANCE
(Ohms)
19,393
18,843
18,311
17,796
17,297
16,814
16,346
15,892
15,453
15,027
14,614
14,214
13,826
13,449
13,084
12,730
12,387
12,053
11,730
11,416
11,112
10,816
10,529
10,250
9,979
9,717
9,461
9,213
8,973
8,739
8,511
8,291
8,076
7,686
7,665
7,468
7,277
7,091
6,911
6,735
6,564
6,399
6,238
6,081
5,929
5,781
5,637
5,497
5,361
5,229
5,101
TEMP
(F)
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
RESISTANCE
(Ohms)
4,976
4,855
4,737
4,622
4,511
4,403
4,298
4,196
4,096
4,000
3,906
3,814
3,726
3,640
3,556
3,474
3,395
3,318
3,243
3,170
3,099
3,031
2,964
2,898
2,835
2,773
2,713
2,655
2,597
2,542
2,488
2,436
2,385
2,335
2,286
2,239
2,192
2,147
2,103
2,060
2,018
1,977
1,937
1,898
1,860
1,822
1,786
1,750
1,715
1,680
1,647
73
TEMP
(F)
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
RESISTANCE
(Ohms)
1,614
1,582
1,550
1,519
1,489
1,459
1,430
1,401
1,373
1,345
1,318
1,291
1,265
1,240
1,214
1,190
1,165
1,141
1,118
1,095
1,072
1,050
1,029
1,007
986
965
945
925
906
887
868
850
832
815
798
782
765
750
734
719
705
690
677
663
650
638
626
614
602
591
581
TEMP
(F)
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
RESISTANCE
(Ohms)
570
561
551
542
533
524
516
508
501
494
487
480
473
467
461
456
450
445
439
434
429
424
419
415
410
405
401
396
391
386
382
377
372
367
361
356
350
344
338
332
325
318
311
304
297
289
282
Table 47B — 5K Thermistor Temperature (°C) vs Resistance/Voltage
TEMP
(C)
–32
–31
–30
–29
–28
–27
–26
–25
–24
–23
–22
–21
–20
–19
–18
–17
–16
–15
–14
–13
–12
–11
–10
–9
–8
–7
–6
–5
–4
–3
–2
–1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
RESISTANCE
(Ohms)
100,260
94,165
88,480
83,170
78,125
73,580
69,250
65,205
61,420
57,875
54,555
51,450
48,536
45,807
43,247
40,845
38,592
38,476
34,489
32,621
30,866
29,216
27,633
26,202
24,827
23,532
22,313
21,163
20,079
19,058
18,094
17,184
16,325
15,515
14,749
14,026
13,342
12,696
12,085
11,506
10,959
10,441
9,949
9,485
9,044
8,627
8,231
TEMP
(C)
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
RESISTANCE
(Ohms)
7,855
7,499
7,161
6,840
6,536
6,246
5,971
5,710
5,461
5,225
5,000
4,786
4,583
4,389
4,204
4,028
3,861
3,701
3,549
3,404
3,266
3,134
3,008
2,888
2,773
2,663
2,559
2,459
2,363
2,272
2,184
2,101
2,021
1,944
1,871
1,801
1,734
1,670
1,609
1,550
1,493
1,439
1,387
1,337
1,290
1,244
1,200
TEMP
(C)
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
RESISTANCE
(Ohms)
1,158
1,118
1,079
1,041
1,006
971
938
906
876
836
805
775
747
719
693
669
645
623
602
583
564
547
531
516
502
489
477
466
456
446
436
427
419
410
402
393
385
376
367
357
346
335
324
312
299
285
pressure transducer. Discharge and suction pressure as measured by the transducers are converted to saturated temperatures. The main control logic for the EXV uses discharge superheat to control the position of the EXV. The difference between the temperature of the discharge gas and the saturated
discharge temperature is the superheat. The EXV module controls the position of the electronic expansion valve stepper motor to maintain the discharge superheat set point.
The EXV control logic has several overrides, which are also
used to control the position of the EXV.
• Approach between SST (Saturated Suction Temperature)
and LWT
• Maximum Operating Pressure (MOP)
Approach — If the approach (pinch), which is the difference
between leaving fluid temperature and saturated suction temperature, is equal to or less than the pinch set point then the
EXV will not open any further even though discharge superheat set point is not met. Pinch set point is calculated using
suction superheat, discharge superheat and pinch offset. Pinch
offset is used to adjust calculated pinch set point do to accuracy
of transducers and thermistors.
MOP — The EXV is also used to limit cooler saturated suction
temperature to 62 F (16.6 C). This makes it possible for the
chiller to start at higher cooler fluid temperatures without overloading the compressor. This is commonly referred to as MOP
(maximum operating pressure). If the SST is equal to or greater
than the MOP set point then the MBB will try to control the
EXV position to maintain the MOP set point.
SERVICE
Each circuit on the
30XA090-500 units has an economizer assembly. The
30XA080,082 units do not have an economizer and have one
main electronic expansion valve. The 30XA080,082 units are
controlled the same way as units with a separate economizer
assembly. See Fig. 46.
Economizer Assembly —
Electronic Expansion Valve (EXV) — See Fig. 47
for a cutaway view of the EXV. High-pressure liquid refrigerant enters valve through the top. As refrigerant passes through
the orifice, pressure drops and refrigerant changes to a 2-phase
condition (liquid and vapor). The electronic expansion valve
operates through an electronically controlled activation of a
stepper motor. The stepper motor stays in position unless power pulses initiate the two discrete sets of motor stator windings
for rotation in either direction. The direction depends on the
phase relationship of the power pulses.
The motor directly operates the spindle, which has rotating
movements that are transformed into linear motion by the
transmission in the cage assembly. The valve cone is a V-port
type which includes a positive shut-off when closed.
The large number of steps and long stroke results in very accurate control of the refrigerant flow. The stepper motor has either 3690 (main) or 2785 (economizer) steps.
FLOODED COOLER MAIN EXV CONTROL — Each
circuit has a thermistor located in the discharge end of the compressor (DGT) and another one located in the compressor motor cavity (SGT). Each circuit also has discharge and suction
74
The discharge superheat leaving the compressor is maintained between approximately 18° and 25° F (10° and 14° C),
or less. Because EXV status is communicated to the Main Base
Board (MBB) and is controlled by the EXV modules, it is possible to track the valve position. The unit is then protected
against loss of charge and a faulty valve. During initial start-up,
the EXV is fully closed. After an initialization period, valve
position is tracked by the EXV module by constantly monitoring the amount of valve movement.
DX (Direct Expansion) COOLER MAIN EXV CONTROL — Each circuit has a thermistor located in a well in the
discharge of the compressor (DGT) and another one located in
the compressor motor cavity (SGT). Thermistors are also located in a well in the water inlet and outlet nozzles. Apart from
thermistors, each circuit also has a discharge and suction pressure transducer. Discharge and suction pressures as measured
by the transducers are converted to saturated temperatures. The
main control logic for the EXV uses approach temperature in
the cooler (Water Inlet Temperature – Saturated Suction Temperature) and suction superheat (Suction Temperature – Saturated Suction Temperature) to control the position of the EXV.
The EXV module controls the position of the electronic expansion valve stepper motor to maintain a minimum approach and
a suction superheat set point.
The EXV control logic has several overrides, which are also
used to control the position of the EXV.
• Maximum Operating Pressure (MOP)
• High Discharge Gas Temperature
• Low Discharge Superheat
MOP — The EXV is also used to limit cooler saturated suction
temperature to 62 F (16.6 C). This makes it possible for the
chiller to start at higher cooler fluid temperatures without overloading the compressor. This is commonly referred to as MOP
(maximum operating pressure). If the SST (Saturated Suction
Temperature) is equal to or greater than the MOP set point then
the MBB will try to control the EXV position to maintain the
MOP set point.
High Discharge Gas Temperature — The EXV is also used to
limit the discharge gas temperature to 200 F (93.3 C). This
makes it possible for the chiller to operate at low load and high
ambient temperature without overloading the compressor. If
the DGT is approaching the High DGT limit then the control
will try to control the EXV position to bring the DGT down by
opening the EXV.
Low Discharge Superheat — The EXV is also used to limit
the discharge superheat (DSH) to 18° F (10° C). This makes it
possible for the chiller to operate at high load and low ambient
temperature without overloading the compressor. If the DSH
goes below 18° F (10° C) the MBB will try to control the EXV
position to bring the discharge superheat up by closing the
EXV valve.
The suction superheat entering the compressor is maintained between approximately 15° and 25° F (8.3° and 14° C)
while maintaining a constant approach in the cooler. Because
EXV status is communicated to the Main Base Board (MBB)
and is controlled by the EXV modules, it is possible to track the
valve position. During initial start-up, the EXV is fully closed.
After an initialization period, valve position is tracked by the
EXV module by constantly monitoring the amount of valve
movement.
ECONOMIZER
RELIEF
ECONOMIZER
FLOW TO
COMPRESSOR
ECONOMIZER
RELIEF
LIQUID LINE
SHUT OFF
VALVE
BRAZE PLATE
HEAT EXCHANGER
ECONOMIZER
EXV
FILTER DRIER
MAIN EXV
*SIGHT GLASS
*Economizer EXV has sight glass
on opposite side of valve shown.
MAIN FLOW
TO COOLER
a30-4468
Fig. 46 — Economizer Assembly
75
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Cable
Glass Seal
Motor Housing
Stepper Motor
Bearing
Lead Screw
Insert
Valve Piston
Valve Seat
Valve Port
a30-4241
Fig. 47 — Cutaway Views of the Electronic Expansion Valve
If the valve is not working properly, continue with the following test procedure:
Check the 8-position DIP switch on the board for the proper
address (see page 11). Check the EXV output signals at appropriate terminals on the EXV module. For 30XA080 units,
connect the positive test lead to EXV-J2A terminal 5 for Circuit
A and to EXV-J2B terminal 5 for Circuit B.
For 30XA090-500 units connect positive test lead to
EXV(X)-J2A terminal 5 for EXV(X) and EXV(X)-J2B terminal 5 for Economizer EXV(X). Using the Service Test procedure on page 105, move the valve output under test to 100%.
DO NOT short meter leads together or pin 5 to any other pin,
as board damage will occur. During the next several seconds,
carefully connect the negative test lead to pins 1,2,3 and 4 in
succession. Digital voltmeters will average this signal and
display approximately 6 vdc. If the output remains at a constant
voltage other than 6 vdc or shows 0 volts, remove the connector to the valve and recheck.
Select 0% to close the valve.
NOTE: Twelve vdc is the output from the EXV board when
the valve is stationary.
See Tables 6 and 7. If a problem still exists, replace the
EXV board. If the reading is correct, the expansion valve and
EXV wiring should be checked. Check the EXV connector and
interconnecting wiring.
1. Check color-coding and wire connections. Make sure
they are connected to the correct terminals at the EXV
board and EXV plug and that the cables are not crossed.
2. Check for continuity and tight connection at all pin
terminals.
Check the resistance of the EXV motor windings. For
30XA080,082 units remove the EXV module plug EXV-J2A
for Circuit A EXV and EXV-J2B for Circuit B EXV. For
30XA090-500 units remove the EXV module plug EXV(X)J2A for main EXV and EXV(X)-J2B for economizer EXV.
Check the resistance of the two windings between pins 1 and 3
for one winding and pins 2 and 4 for the other winding. The
resistance should be 52 ohms (± 5.2 ohms). Also check pins 1-4
for any shorts to ground.
ECONOMIZER EXV CONTROL — The economizer EXV
is controlled by the circuit EXV board. There is an economizer
gas temperature thermistor and economizer pressure transducer
located in the line, which runs from the economizer assembly to
the compressor. The economizer pressure is converted to saturated temperature and is used to calculate economizer superheat.
Economizer superheat equals economizer temperature minus
saturated economizer temperature. The economizer EXV only
operates during normal conditions when the capacity of the
circuit is greater than 75%. Once the capacity of the circuit is
greater than 75% the MBB will start controlling the economizer
EXV to maintain economizer superheat set point, which is approximately 8° to 12° F (4.4° to 6.7° C). If the circuit capacity is
less than 75%, the economizer EXV will be closed.
The economizer EXV has one override. If the discharge gas
temperature exceeds 195 F (90.6 C) the economizer EXV will
start to open. The EXV will be controlled to maintain discharge
gas temperature at approximately 195 F (90.6 C).
If it appears that main EXV or economizer EXV is not
properly controlling circuit operation to maintain correct superheat, there are a number of checks that can be made using test
functions and initialization features built into the microprocessor control. See the Service Test section to test EXVs.
EXV TROUBLESHOOTING PROCEDURE — There are
two different economizer EXVs. Both of the economizer
EXVs have a total of 2785 steps. There are three different main
EXVs, which all have a total of 3690 steps. The EXV motor
moves at 150 steps per second. Commanding the valve to
either 0% or 100% will add an additional 160 steps to the
move, to ensure the valve is open or closed completely.
Follow the steps below to diagnose and correct EXV
problems. Check EXV motor operation first. Switch the
Enable/Off/Remote (EOR) Contact switch to the Off position.
Check the appropriate circuit EXV, Circuit A EXV % Open
(Circuit A EXV Position, EXV.A), Circuit B EXV % Open
(Circuit B EXV Position, EXV.B), or Circuit C EXV % Open
(Circuit C EXV Position, EXV.C). The current value of 0 will
be displayed. Increase the EXV position to select 100% valve
position. The actuator should be felt moving through the EXV.
To close the valve, select 0%. The actuator should knock when
it reaches the bottom of its stroke. See Table 48 for a list of
EXV modes and submodes.
76
Table 48 — EXV Modes and Submodes
EXV TYPE AND CIRCUIT
EXV, Circuit A
EXV, Circuit B
EXV, Circuit C
Economizer EXV, Circuit A
Economizer EXV, Circuit B
Economizer EXV, Circuit C
TOUCH PILOT™ PATH
Main MenuStatusCIRCA_AN
Main MenuStatusCIRCB_AN
Main MenuStatusCIRCC_AN
Main MenuStatusQCK_TST1
Main MenuStatusQCK_TST1
Main MenuStatusQCK_TST1
NAVIGATOR™ PATH
Service Test ModeQUICEXV.A
Service Test ModeQUICEXV.B
Service Test ModeQUICEXV.C
Service Test ModeQUICECO.A
Service Test ModeQUICECO.B
Service Test ModeQUICECO.C
Installing EXV Motor
Inspecting/Opening Electronic Expansion Valves
IMPORTANT: Obtain replacement gaskets before
opening EXV. Do not re-use gaskets.
IMPORTANT: Obtain replacement gasket before
opening EXV. Do not re-use gaskets.
To check the physical operation of an EXV, the following
steps must be performed if the unit does not have service valve
option or activated ball valves (ABV) (flooded coolers only)
the complete charge needs to be recovered using proper recovery techniques Steps 1-3 shown below. If the unit has ABV or
discharge service valves, only perform Steps 1 and 2.
1. Close the liquid line service valve of the circuit to be
checked. Put the Enable/Off/Remote Contact switch in
the Off position. Enter the Service Test mode and change
Service Test Enable, T.REQ from OFF to ON. A password may be required. Switch the EOR switch to the
Enable position. Under the COMP sub-mode, enable one
of the compressors (CP.xn) for the circuit. Let compressor run until gage on suction pressure port reads 10 psig
(68.9 kPa). Turn the compressor off. The compressor will
turn off. Immediately after the compressor shuts off,
manually close the actuated ball valve (ABV) (see the
Actuated Ball Valve section for instructions). If the unit is
equipped with suction service valves, discharge service
valve, and economizer service valves, close all valves.
Closing the valves will minimize the amount of charge
that will have to be removed from the system after pump
down.
2. Remove any remaining refrigerant from the system low
side using proper recovering techniques. The economizer
assembly has a 1/4-in. access connection which can be
used to remove charge from the inlet of the EXVs. Turn
off the line voltage power supply to the compressors.
If re-installing the motor, be sure to use a new gasket in the
assembly. See Fig. 48. It is easier to install the motor assembly
with the piston in the fully closed position. Insert the motor into
the body of the EXV. Tighten the motor to the body to 36 ft-lb
(50 N-m) and then tighten the valve another 30 degrees.
Moisture Liquid Indicator — Clear flow of liquid refrigerant
indicates sufficient charge in system. Bubbles in the sight glass
indicate undercharged system or presence of noncondensables.
Moisture in system, measured in parts per million (ppm),
changes color of indicator. See Table 49. Change filter drier at
first sign of moisture in system.
Table 49 — Color Indicators when
Moisture is Present in Refrigerant
COLOR
INDICATOR
Green — Dry
Yellow-green — Caution
Yellow — Wet
R-134A,
75 F (24 C)
(ppm)
<30
30-100
>100
R-134A,
125 F (52 C)
(ppm)
<45
45-170
>170
IMPORTANT: Unit must be in operation at least
12 hours before moisture indicator can give an accurate reading.
With unit running, indicating element must be in contact with liquid refrigerant to give true reading.
Filter Drier — Whenever moisture-liquid indicator shows
presence of moisture, replace filter drier(s). There is one filter
drier assembly on each circuit with either one or two cores.
The 30XA080-122 units have one core per circuit. The
30XA140-162 units have two cores, in circuit A and one for
circuit B. The 30XA180-500 units have two cores per circuit.
Refer to the Carrier Standard Service Techniques Manual,
Chapter 1, Refrigerants, for details on servicing filter driers.
Liquid Line Service Valve — This valve is located immediately
ahead of filter drier, and has a 1/4-in. access connection for field
charging. In combination with compressor discharge service
valve, each circuit can be pumped down into the high side for
servicing.
CAUTION
Ensure refrigerant is removed from both the inlet and outlet
of EXV assemblies. Equipment damage could result.
3. The expansion valve motor is hermetically sealed inside
the top portion of the valve. See Fig. 47. Disconnect the
EXV plug. Carefully unscrew the motor portion from the
body of the valve. The EXV operator will come out with
the motor portion of the device. Reconnect the EXV plug.
4. Enter the appropriate EXV test step under the (QUIC)
Service Test mode Locate the desired item Circuit A
EXV Position, EXV.A, Circuit B EXV Position,
EXV.B, or Circuit C EXV Position, EXV.C. Change the
position to 100%. Observe the operation of the lead
screw. See Fig. 47. The motor should be turning, raising
the operator closer to the motor. Motor actuator movement should be smooth and uniform from fully closed to
fully open position. Select 0% and check open to closed
operation. If the valve is properly connected to the processor and receiving correct signals, yet does not operate
as described above, the sealed motor portion of the valve
should be replaced.
Compressor Assembly — The 30XA units utilize
screw compressors with a modulating slide valve which varies
capacity from 30% to 100% of compressor capacity for each
circuit. See Fig. 49 for a view of a typical 06T compressor.
The slide valve position is varied by opening and closing the
2 solenoid valves located on the compressor. To unload the
compressor, both solenoids are deenergized. To increase in
capacity both solenoid valves are energized together which
will cause the slide valve to slide towards the fully loaded
position. To stop the loading process solenoid 2 is energized
and solenoid 1 is deenergized. This will cause the slide valve to
maintain its current position. There is no feedback for the position of the slide valve. The control utilizes compressor current
77
• ISO Viscosity Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
as an indicator of the slide valve position. Once the calculated
position of the slide valve reaches 100% circuit capacity, the
control will try to increase capacity again if the compressor
current continues to increase. The control will continue to load
the compressor until the compressor current no longer
increases. At that time the control will energize both solenoids
and the circuit will be considered fully loaded.
COMPRESSOR OIL SYSTEM — Each compressor/circuit
has its own oil system which includes an oil filter, oil solenoid,
check valve, oil level switch, oil separator heater, oil pressure
transducer, and an oil shut-off valve. A typical oil system is
shown in Fig. 50. See Table 50.
Do not reuse drained oil or any oil that has been exposed to the
atmosphere.
Oil is available in the following quantities from your local
Carrier representative:
QUANTITY
1 Quart
1 Gallon
5 Gallon
If unsure if there is low oil charge in the system, follow the
steps below:
1. If the unit shuts off repeatedly from a low oil level alert it
may be an indication of inadequate oil charge; however, it
could also indicate that the oil is not being reclaimed from
the low-side of the system.
2. Begin running the unit at full load for 11/2 hours. Use the
manual Test Mode feature of Service Test if the unit does
not normally run at full load.
NOTE: An adequate load must be available.
3. After running the unit for 11/2 hours at full load, allow the
unit to restart and run normally. If low oil alarms persist,
continue with the following steps.
4. Close the liquid line service valve and place a pressure
gage on top of the cooler or suction line service port. Enable the Service Test feature and turn the Enable/Off/Remote switch to the enable position. Start the desired circuit by turning it on under the TEST function: CP.A for
compressor A, CP.B for compressor B, or CP.C for compressor C.
Table 50 — Unit Oil Quantities
30XA UNIT SIZE
080-122
140-162
180-202
220,222
240,242
260,262
280-302
325-352
400
450
500
TOTALINE PART NO.
P903-2325
P903-2301
P903-2305
OIL CHANGE (gal, [liters])
Circuit A
Circuit B
Circuit C
5.5 [20.8]
5.5 [20.8]
—
6.25 [23.7]
5.5 [20.8]
—
6.25 [23.7]
6.25 [23.7]
—
6.75 [25.6]
6.25 [23.7]
—
6.75 [25.6]
6.75 [25.6]
—
7.50 [28.4]
6.75 [25.6]
—
7.50 [28.4]
6.75 [25.6]
—
7.50 [28.4]
7.50 [28.4]
—
6.75 [25.6]
6.75 [25.6]
7.50 [28.4]
7.50 [28.4]
6.25 [23.7]
7.50 [28.4]
7.50 [28.4]
6.75 [25.6]
7.50 [28.4]
Oil Charge — When additional oil or a complete charge is
required it must meet the following specifications:
• Manufacturer . . . . . . . . . . . . . . . . . . . . . Emkarate RL220XL
• Oil Type . . . . . . . . . . . . . . . . . . . Inhibited polyolester-based
synthetic compressor lubricant for use with screw compressors.
DISASSEMBLY
Closed
Open
NOTE: Open valve in QuickOPEN
Test sub-mode
before
disassembling.
VALVE IN QUICK
TEST
SUB-MODE BEFORE DISASSEMBLING
ASSEMBLY
Closed
Open
GASKET
EF05BD271
EF05BD331
mm
mm
a30-4072
NOTES:
1. Push down on valve piston to close valve before assembling.
2. After valve is assembled close valve in Quick Test sub-mode or cycle power before opening service valve.
Fig. 48 — Disassembly and Assembly of EXV Motor
78
5. When the compressor starts successfully, observe the
cooler pressure. When the pressure reads 10 psig
(68.9 kPa), turn the Emergency Switch (SW2) to the OFF
position. The compressor should stop.
6. Open the liquid line service valve and allow the unit to
restart normally. If low oil level alarms persist, continue
with the following steps.
7. If none of the previous steps were successful, the unit is
low on oil charge. Add oil to the oil separator using the
1/ in. access fitting that the discharge pressure transducer
4
is mounted to.
NOTE: To facilitate the oil charging process, ensure that
the unit is not running when adding oil. The system is under pressure even when the unit is not running, so it is
necessary to use a suitable pump to add oil to the system.
Using a suitable pump, add 1/2 gal (1.9 l) of oil to the system. Continue adding oil in 1/2 gal (1.9 l) increments until
the problem is resolved, up to a maximum of 1.5 gal
(5.7 l). If it is necessary to add factory oil charge levels to
the system contact your local Carrier representative.
Oil Filter Maintenance — Each circuit has one oil filter located externally to the compressor. Oil line pressure drop is
monitored by the control. Oil line pressure drop is calculated
by subtracting oil pressure (OP) from discharge pressure (DP).
If the oil line pressure drop exceeds 30 psi (206.8 kPa) for
5 minutes the control will generate a High Oil Filter Pressure
Drop alert. The High Oil Filter Pressure Drop alert will
not shut down the compressor, but instead indicates that the
oil filter is dirty. If oil pressure line losses exceed 50 psi
(344.7 kPa) then the control will shut down the circuit on
Maximum Oil Filter Differential Pressure Failure.
CAUTION
Compressor oil is pressurized. Use proper safety precautions when relieving pressure.
Replacing the Oil Filter — Close the oil line ball valve located in front of the oil filter. Connect a charging hose to the 1/4-in.
access fitting port located downstream of the valve and bleed
off oil trapped between the service valve and the oil solenoid
valve. A quart of oil is typically what is removed during this
process. Remove the charging hose. Unscrew the nuts from
both ends of the oil filter and remove the oil filter. Remove the
protective caps from the new oil filter and install, being careful
not to lose or damage the new O-ring located on the new oil filter. Draw a vacuum at the Schrader port. Remove the charging
hose and open the oil line ball valve. Check both fittings for
leaks.
Flooded Cooler Units
FLOODED COOLER UNIT SUCTION SERVICE
VALVE — The suction service valve is a factory-installed option for 30XA units. It is located in the suction outlet of the
cooler. The suction service valve is bolted between the cooler
outlet and the suction flange piping. The suction service valve
shaft has a locking device located on the shaft to lock the valve
in either a fully open position or a fully closed position. The
locking device must be pulled out prior to moving the valve
handle to a fully open or a fully closed position. See Fig. 51A
and 51B.
OIL PRESSURE SUCTION
TRANSDUCER TEMPERATURE
LOCATION
DISCHARGE
GAS THERMISTOR
ACCESS
FITTING
MOTOR TEMPERATURE
SENSOR 1
COMMON
MOTOR TEMPERATURE
SENSOR 2
HIGH PRESSURE
SWITCH
Unloader Piston
Chamber
text
Slide Valve
Discharge
Port
Discharge
Port
text
Slide Valve
l
text
Discharge
Port
Bleed Line to Low Pressure Suction
High Pressure Oil
De-energized
FLOW
Valve #2 (NO)
De-energized
NO FLOW
Valve #1 (NC)
High Pressure Oil
Energized
NO FLOW
Valve #2 (NO)
FULLY UNLOADED OPERATION
Fig. 49 — Typical 06T Compressor (All Units)
79
Slide
Valve
Slide
Valve
Part Load Position
Bleed Line to Low Pressure Suction
High Pressure Oil
FULLY LOADED OPERATION
Trapped
Oil at
High
Pressure
Unloaded Position
Bleed Line to Low Pressure Suction
Energized
FLOW
Valve #1 (NC)
Compression
Process
Compression
Process
Loaded Position
Energized
NO FLOW
Valve #2 (NO)
SOLENOID 1
Unloader Piston
Chamber
Unloader Piston
Chamber
Compression
Process
Drain to
Low Pressure
High with
High
Pressure
Oil
SOLENOID 2
De-energized
NO FLOW
Valve #1 (NC)
MAINTAIN POSITION
a30-4469
HIGH
PRESSURE
TRANSDUCER
OIL
SEPARATOR
HEATER
(BOTTOM)
OIL
FILTER
OIL
PRESSURE
TRANSDUCER
OIL LEVEL
SWITCH
(BOTTOM)
OIL SHUT OFF
VALVE
OIL
SOLENOID
VALVE
CHECK
VALVE
a30-4243
Fig. 50 — Typical Oil System (All Units)
FLOODED COOLER FREEZE PROTECTION — All
coolers are equipped with cooler heaters and are controlled by
the Main Base Board. The control logic uses the unit status,
outdoor air temperature, and the saturated suction temperatures
for all circuits to decide if the cooler heater should be energized. The cooler heaters can only be energized when the state
of the unit is OFF. The cooler heaters will be energized if the
outdoor-air temperature is less than the Cooler Heater Set Point
and the lowest circuit Saturated Suction Temperature is less
than the heater set point plus 6° F (3.3° C). See Table 51. The
cooler heater set point = freeze point + Cooler Heater DT Setp
(Cooler Heater Delta Spt, HTR). If the entering or leaving
water temperature is less than the Heater Set Point and the outdoor air temperature is less than the Heater Set Point –2° F
(1.1° C), then the heater will be turned on.
If the Entering or Leaving Water Temperature is less than
the Brine Freeze Setpoint (Brine Freeze Setpoint, LOSP)
+1.0° F (0.5° C), then the heater will be turned on along with
the pump.
The entire cooler is covered with closed-cell insulation
applied over the heater. The heater plus insulation protects
cooler against low ambient temperature freeze-up to 0° F
(–17.8 C).
a30-5246
Fig. 51A — Suction Service Valve Locking Device,
Closed and Unlocked (Flooded Cooler Units)
IMPORTANT: If unit is installed in an area where
ambient temperatures fall below 32 F (0° C), a suitable
corrosion-inhibited antifreeze solution or cooler heater
must be used in the chilled water circuit.
FLOODED COOLER LOW FLUID TEMPERATURE —
Main Base Board is programmed to shut chiller down if leaving fluid temperature drops below 34 F (1.1 C) for cooler fluid
type water or below Brine Freeze Setpoint (Brine Freeze Setpoint, LOSP) for cooler fluid type brine. The unit will shut
down without a pumpout. When fluid temperature rises to
6° F (3.3° C) above the leaving fluid set point, safety resets and
chiller restarts. Reset is automatic as long as this is the first
occurrence.
VALVE
LOCKED
OPEN
a30-5247
Fig. 51B — Suction Service Valve Locking Device,
Open and Locked (Flooded Cooler Units)
80
Table 51 — Cooler Heater Operation Examples for Flooded Coolers
OAT
F (C)
UNIT
STATUS
BRINE
FREEZE
POINT
F (C)
COOLER
DELTA T
F (C)
COOLER
HEATER
SETPOINT
F (C)
SSTA
F (C)
SSTB
F (C)
SSTC
F (C)
COOLER
HEATER
STATUS
50
(10)
OFF
36
(2.2)
6
(3.3)
42
(5.6)
N/A
N/A
N/A
OFF
40
(4.4)
OFF
36
(2.2)
6
(3.3)
42
(5.6)
41
(5)
N/A
N/A
ON
40
(4.4)
OFF
15
(–9.4)
6
(3.3)
21
(–6.1)
41
(5)
N/A
N/A
OFF
40
(4.4)
OFF
36
(2.2)
6
(3.3)
42
(5.6)
52.1
(11.2)
52.1
(11.2)
52.1
(11.2)
OFF
40
(4.4)
ON
36
(2.2)
6
(3.3)
42
(5.6)
N/A
N/A
N/A
OFF
N/A
OAT
SSTA
SSTB
SSTC
—
—
—
—
—
COMMENTS
OAT
>42 F
(5.6 C)
SSTA
<42 F
(5.6 C)
SSTA
>21 F
(–6.1 C)
All SST
Temperatures
>52 F
(11.2 C)
Unit Status
ON
LEGEND
Not Applicable
Outdoor-Air Temperature
Saturated Suction Temperature, Circuit A
Saturated Suction Temperature, Circuit B
Saturated Suction Temperature, Circuit C
FLOODED COOLER LOSS OF FLUID FLOW PROTECTION — All 30XA ma-chines include an integral flow switch
that protects the cooler against loss of cooler flow.
FLOODED COOLER TUBE PLUGGING — A leaky tube
can be plugged until retubing can be done. The number of
tubes plugged determines how soon the cooler must be
retubed. All tubes in the cooler may be removed. Loss of unit
capacity and efficiency as well as increased pump power will
result from plugging tubes. Failed tubes should be replaced as
soon as possible. Up to 10% of the total number of tubes can
be plugged before retubing is necessary. Figure 52 shows an
Elliott tube plug and a cross-sectional view of a plug in place.
See Tables 52 and 53 for plug components. If the tube failure
occurs in both circuits using tube plugs will not correct the
problem. Contact your local Carrier representative for assistance.
Table 52 — Plug Component Parts
(Flooded Cooler Units Only)
COMPONENT
For Tubes
Brass Pin
Brass Ring
PART NUMBER
853103-1*
853002-640 or 657*
(measure tube
before ordering)
For Holes without tubes
Brass Pin
Brass Ring
Loctite
Locquic
Roller Extension
853103-1A
85102-738
No. 675 †
“N”†
S82-112/11
*Order directly from Elliot Tube Company, Dayton, OH or RCD.
†Can be obtained locally.
CAUTION
Table 53 — Flooded Cooler Tube Components
Use extreme care when installing plugs to prevent damage
to the tube sheet section between the holes.
COMPONENT
FLOODED COOLER RETUBING — When retubing is required, obtain service of qualified personnel experienced in
boiler maintenance and repair. Most standard procedures can
be followed when retubing the coolers. An 8% crush is recommended when rolling replacement tubes into the tubesheet.
Place one drop of Loctite No. 675 or equivalent on top of
tube prior to rolling. This material is intended to “wick” into
the area of the tube that is not rolled into the tube sheet, and
prevent fluid from accumulating between the tube and the tube
sheet. New tubes must also be rolled into the center tubesheet
to prevent circuit to circuit leaks.
Tube sheet hole diameter
Tube OD
Tube ID after rolling (includes
expansion due to clearance.)
SIZE
in.
0.756
0.750
0.650 to
0.667
mm
19.20
19.05
16.51 to 16.94
NOTE: Tubes replaced along heat exchanger head partitions must
be flush with tube sheet (both ends).
FLOODED COOLER TIGHTENING COOLER HEAD
BOLTS
Preparation — When reassembling cooler heads, always
check the condition of the O-rings first. The O-ring should be
replaced if there is visible signs of deterioration, cuts or
damage. Apply a thin film of grease to the O-ring before
installation. This will aid in holding the O-ring in the groove
while the head is installed. Torque all bolts to the following
specification and in sequence:
3/ -in. Diameter Perimeter Bolts (Grade 5) . . . 200 to 225 ft-lb
4
(271 to 305 N-m)
a30-4083
Fig. 52 — Elliott Tube Plug
81
located in the suction line for each circuit. The suction service
valve is either a ball valve type valve or a butterfly type valve.
DX COOLER FREEZE PROTECTION — Coolers can be
ordered with heaters installed in the factory. If equipped, the
main base board based on the outdoor-air temperature and the
entering and leaving water thermistors controls the cooler heaters. The Heater Set Point is the sum of the freeze point and
Cooler Heater DT Setp (ConfigurationSERVHTR).
If the entering or leaving water temperature is less than the
Heater Set Point and the outdoor air temperature is less than
the Heater Set Point – 2° F (1.1° C), then the heater will be
turned on.
If the Entering or Leaving Water Temperature is less than
the Brine Freeze Setpoint (ConfigurationSERVLOSP) +
1.0° F (0.5° C), then the heater will be turned on along with the
pump.
Entire cooler is covered with closed-cell insulation applied
over the heater. Heater plus insulation protect cooler against
low ambient temperature freeze-up to –20 F (–28 C).
1. Install all bolts finger tight.
2. Bolt tightening sequence is outlined in Fig. 53. Follow
the numbering or lettering sequence so that pressure is
evenly applied to O-ring.
3. Apply torque in one-third steps until required torque is
reached. Load all bolts to each one-third step before proceeding to next one-third step.
4. No less than one hour later, retighten all bolts to required
torque values.
5. After refrigerant is restored to system, check for refrigerant leaks using recommended industry practices.
6. Replace cooler insulation.
10
SINGLE
PASS
ONLY
9
6
5
15
13
3
2
1
4
IMPORTANT: If unit is installed in an area where
ambient temperatures fall below 32 F (0° C), it is recommended that a suitable corrosion-inhibited antifreeze solution be used in chilled water circuit.
DX COOLER LIQUID FLUID TEMPERATURE — Main
Base Board is programmed to shut chiller down if leaving fluid
temperature drops below 34 F (1.1 C) for cooler fluid type water or below Brine Freeze Setpoint (Brine Freeze Setpoint,
LOSP) for cooler fluid type brine. The unit will shut down
without a pumpout. When fluid temperature rises to 6 F (3.3 C)
above the leaving fluid set point, safety resets and chiller restarts. Reset to automatic as long as this is the first occurance.
DX COOLER LOSS OF FLUID FLOW PROTECTION — All 30XA machines include an integral flow switch
that protects the cooler against loss of cooler flow.
DX COOLER TUBE PLUGGING — A leaky tube can be
plugged until retubing can be done. The number of tubes
plugged determines how soon the cooler must be retubed. If
several tubes require plugging, check with a local Carrier representative to find out how the number and location of tubes
can affect unit capacity. Fig. 54 shows an Elliott tube plug and
a cross-sectional view of a plug in place. See Tables 54 and 55
for plug components.
14
16
8
7
12
11
a30-4246
Fig. 53 — Flooded Cooler Unit Head
Recommended Bolt Torque Sequence
FLOODED COOLER INSPECTING/CLEANING HEAT
EXCHANGERS — Inspect and clean cooler tubes at the end
of the first operating season. Because these tubes have internal
ridges, a rotary-type tube cleaning system is necessary to fully
clean the tubes. Tube condition in the cooler will determine the
scheduled frequency for cleaning, and will indicate whether
water treatment is adequate in the chilled water/brine circuit.
Inspect the entering and leaving water thermistor wells for
signs of corrosion or scale. Replace the well if corroded or remove any scale if found.
CAUTION
CAUTION
Hard scale may require chemical treatment for its prevention or removal. Consult a water treatment specialist for
proper treatment procedures.
Use extreme care when installing plugs to prevent damage
to the tube sheet section between the holes.
Table 54 — DX Cooler Unit Plug Component Part
Numbers
FLOODED COOLER WATER TREATMENT — Untreated or improperly treated water may result in corrosion, scaling,
erosion or algae. The services of a qualified water treatment
specialist should be obtained to develop and monitor a treatment program.
COMPONENTS FOR PLUGGING
For Tubes
Brass Pin
Brass Ring
For Holes without tubes
Brass Pin
Brass Ring
Loctite
Locquic
CAUTION
Water must be within design flow limits, clean and treated
to ensure proper machine performance and reduce the
potential of tubing damage due to corrosion, scaling, and
algae. Carrier assumes no responsibility for cooler damage
resulting from untreated or improperly treated water.
PART NUMBER
853103-312*
853002-322*
853103-375
853002-377
No. 675 †
“N” †
*Order directly from Elliot Tube Company, Dayton, OH or RCD.
†Can be obtained locally.
DX Cooler Units
DX COOLER SUCTION SERVICE VALVE — The suction
service valve is a factory-installed option for 30XA units. It is
82
Table 55 — DX Cooler Unit Plug Component
Dimensions
Place one drop of Loctite No. 675 or equivalent on top of
tube prior to rolling. This material is intended to “wick” into the
area of the tube that is not rolled into the tube sheet, and prevent
fluid from accumulating between the tube and the tube sheet.
DX COOLER TIGHTENING COOLER HEAD BOLTS
(Fig. 55-58)
Gasket Preparation — When reassembling cooler heads, always use new gaskets. Gaskets are neoprene-based and are
brushed with a light film of compressor oil. Do not soak gasket
or gasket deterioration will result. Use new gaskets within
30 minutes to prevent deterioration. Reassemble cooler nozzle
end or plain end cover of the cooler with the gaskets. Torque all
cooler bolts to the following specification and sequence:
5/ -in. Diameter Perimeter Bolts (Grade 5) . . . 150 to 170 ft-lb
8
(201 to 228 N-m)
1/ -in. Diameter Flange Bolts (Grade 5) . . . . . . . . 70 to 90 ft-lb
2
(94 to 121 N-m)
1/ -in. Diameter Center Stud (Grade 5). . . . . . . . . 70 to 90 ft-lb
2
(94 to 121 N-m)
1. Install all bolts finger tight, except for the suction flange
bolts. Installing these flanges will interfere with tightening the center stud nuts.
2. Bolt tightening sequence is outlined in Fig. 55-58. Follow
the numbering or lettering sequence so that pressure is
evenly applied to gasket.
3. Apply torque in one-third steps until required torque is
reached. Load all bolts to each one-third step before proceeding to next one-third step.
4. No less than one hour later, retighten all bolts to required
torque values.
5. After refrigerant is restored to system, check for refrigerant leaks using recommended industry practices.
6. Replace cooler insulation.
SIZE
in.
mm
0.377-0.382
9.58-9.70
0.373-0.377
9.47-9.58
PLUG COMPONENT
Tube sheet hole diameter
Tube OD
Tube ID after rolling (includes
expansion due to clearance.)
0.328
8.33
NOTE: Tubes next to gasket webs must be flush with tube sheet
(both ends).
Fig. 54 — Elliott Tube Plug
For the 30XA142,162,182,202,222,242,262,282,302,327,
352 DX coolers, the pass partition has a perforated distribution
plate in the inlet pass to more uniformly distribute the refrigerant as it enters the tubes of the cooler. The perforated distribution plate is on the tubesheet side of the pass partition. A tube
plug will interfere with the installation of pass partition. The
tube plug must be flush with the tube sheet to prevent this interference. The pass partition is symmetrical, meaning the partition plate can be rotated 180 degrees, however, the performance
of the machine will be affected if the pass partition is installed
incorrectly.
DX COOLER RETUBING — When retubing is required,
obtain service of qualified personnel experienced in boiler
maintenance and repair. Most standard procedures can be followed when retubing the coolers. An 8% crush is recommended when rolling replacement tubes into the tubesheet.
The following Elliott Co. tube rolling tools are required:
• Expander Assembly
• Cage
• Mandrel
• Rolls
15
6
8
a30-5330
10
13
4
19
23
15
2
25
27
28
29
1
29
26
24
3
5
18
14
11 7
9
21
25
28
3
22
16
17
1
26
20
22
24
20
5
16
18
14
12
11
7
Fig. 55 — Bolt Tightening Sequence, 30XA082,092,102,122
83
13
2
23
21
10
4
19
17
27
6
8
9
12
17
13 9
6 11
a30-5331
4
21
25
1
28
3
24
20
5
16
12 7
8 10
6 11
17
21
25
19
23
2
29
31
13 9
15
4
15
19
23
27
30
29
31
2
1
27
30
26
22
18
14
28
3
26
22
18
24
20
5
16
12 7
8 10
14
Fig. 56 — Bolt Tightening Sequence, 30XA142,162,182,202
a30-5407
Fig. 57 — Bolt Tightening Sequence, 30XA222, 242, 262, 282
a30-5408
Fig. 58 — Bolt Tightening Sequence, 30XA302, 327, 352
DX COOLER CHILLED WATER FLOW SWITCH — A
factory-installed flow switch is installed in the entering water
nozzle for all machines. See Fig. 59 and 60. This is a thermaldispersion flow switch. Figure 59 shows typical installation. If
nuisance trips of the sensor are occurring, follow the steps below to correct:
1. Check to confirm that all strainers are clean, valves are
open and pumps are running. For the case of variable
frequency drive (VFD) controlled pumps, ensure the
minimum speed setting has not been changed.
2. Measure the pressure drop across the cooler. Use the
cooler pressure drop curves on pages 62-67 to calculate
the flow and compare this to system requirements.
DX Cooler and Flooded Cooler Units
PREPARATION FOR WINTER SHUTDOWN — If the
unit is not operational during the winter months, at the end of
cooling season complete the following steps.
CAUTION
Failure to remove power before draining heater equipped
coolers and hydronic packages can result in heater tape and
insulation damage.
1. If the unit has optional heater tapes on the cooler and the
cooler will not be drained, do not shut off power disconnect during off-season shutdown. If the unit has optional
84
2.
3.
4.
5.
At the beginning of the next cooling season, be sure that
there is refrigerant pressure on each circuit before refilling
cooler, add recommended inhibitor, and reset the CB-HT (circuit breaker heater) (if opened) or restore power.
heater tapes on the cooler and the cooler is drained, open
the circuit breaker for the heater, CB-13 or shut off power
during off-season shutdown.
Draining the fluid from the system is highly recommended. If the unit is equipped with a hydronic package, there
are additional drains in the pump housing and strainer
that must be opened to allow for all for all of the water to
drain.
Isolate the cooler from the rest of the system with water
shutoff valves.
Replace the drain plug and completely fill the cooler with
a mixture of water and a suitable corrosion-inhibited antifreeze solution such as propylene glycol. The concentration should be adequate to provide freeze protection to
15° F (8.3° C) below the expected low ambient temperature conditions. Antifreeze can be added through the vent
on top of the cooler. If the unit has a hydronic pump package, the pump must be treated in the same manner.
Leave the cooler filled with the antifreeze solution for the
winter, or drain if desired. Be sure to deenergize heaters
(if installed) as explained in Step 1 to prevent damage.
Use an approved method of disposal when removing antifreeze solution.
Microchannel Heat Exchanger (MCHX) Condenser Coil Maintenance and Cleaning Recommendations — Routine cleaning of coil surfaces is
essential to maintain proper operation of the unit. Elimination
of contamination and removal of harmful residues will greatly
increase the life of the coil and extend the life of the unit. The
following steps should be taken to clean MCHX condenser
coils:
CAUTION
Do not apply any chemical cleaners to MCHX condenser
coils. These cleaners can accelerate corrosion and damage
the coil.
1. Remove any foreign objects or debris attached to the coil
face or trapped within the mounting frame and brackets.
2. Put on personal protective equipment including safety
glasses and/or face shield, waterproof clothing and
gloves. It is recommended to use full coverage clothing.
3. Start high pressure water sprayer and purge any soap or
industrial cleaners from sprayer before cleaning condenser coils. Only clean potable water is authorized for cleaning condenser coils.
4. Clean condenser face by spraying the coil steady and uniformly from top to bottom while directing the spray
straight toward the coil. Do not exceed 900 psig
(6205 kPa) or 30 degree angle. The nozzle must be at
least 12 in. (304.8 mm) from the coil face. Reduce pressure and use caution to prevent damage to air centers.
a30-5334
L1
24 VAC
N
BRN
1
WHT
2
BLK
4
BLU
3
CAUTION
Excessive water pressure will fracture the braze between
air centers and refrigerant tubes.
Fig. 59 — Chilled Water Flow Switch
RTPF (Round Tube Plate Fin) Condenser Coil
Maintenance and Cleaning Recommendations — Routine cleaning of coil surfaces is essential to
a30-5335
maintain proper operation of the unit. Elimination of contamination and removal of harmful residues will greatly increase
the life of the coil and extend the life of the unit. The following
maintenance and cleaning procedures are recommended as part
of the routine maintenance activities to extend the life of the
coil.
REMOVE SURFACE LOADED FIBERS — Surface loaded fibers or dirt should be removed with a vacuum cleaner. If a
vacuum cleaner is not available, a soft non-metallic bristle
brush may be used. In either case, the tool should be applied in
the direction of the fins. Coil surfaces can be easily damaged
(fin edges can be easily bent over and damage to the coating of
a protected coil) if the tool is applied across the fins.
NOTE: Use of a water stream, such as a garden hose, against a
surface loaded coil will drive the fibers and dirt into the coil.
This will make cleaning efforts more difficult. Surface loaded
fibers must be completely removed prior to using low velocity
clean water rinse.
PERIODIC CLEAN WATER RINSE — A periodic clean
water rinse is very beneficial for coils that are applied in coastal
or industrial environments. However, it is very important that
the water rinse is made with very low velocity water stream to
avoid damaging the fin edges. Monthly cleaning as described
below is recommended.
OUT
IN
FLOW SWITCH
STANDARD FLOODED COOLER
Fig. 60 — Flow Switch
85
7. Ensure cleaner thoroughly penetrates deep into finned
areas.
8. Interior and exterior finned areas must be thoroughly
cleaned.
9. Finned surfaces should remain wet with cleaning solution
for 10 minutes.
10. Ensure surfaces are not allowed to dry before rinsing.
Reapplying cleaner as needed to ensure 10-minute
saturation is achieved.
11. Thoroughly rinse all surfaces with low velocity clean
water using downward rinsing motion of water spray
nozzle. Protect fins from damage from the spray nozzle.
ROUTINE CLEANING FOR RTPF COIL SURFACE —
Monthly cleaning with Totaline® environmentally sound coil
cleaner is essential to extend the life of coils. This cleaner is
available from Carrier Replacement Parts division as part number P902-0301 for a one gallon container, and part number
P902-0305 for a five gallon container. It is recommended that
all coils, including the standard copper tube aluminum fin, precoated fin, copper fin, or e-coated coils be cleaned with the
Totaline environmentally sound coil cleaner as described
below. Coil cleaning should be part of the unit’s regularly
scheduled maintenance procedures to ensure long life of the
coil. Failure to clean the coils may result in reduced durability
in the environment. Avoid the use of:
• coil brighteners
• acid cleaning prior to painting
• high pressure washers
• poor quality water for cleaning
Totaline environmentally sound coil cleaner is non-flammable, hypoallergenic, nonbacterial, and a USDA accepted biodegradable agent that will not harm the coil or surrounding components such as electrical wiring, painted metal surfaces, or insulation. Use of non-recommended coil cleaners is stongly
discouraged since coil and unit durability could be affected.
Totaline Environmentally Sound Coil Cleaner Application
Equipment
• 21/2 gallon garden sprayer
• Water rinse with low velocity spray nozzle
Condenser Fans — A formed metal mount bolted to fan
deck supports each fan and motor assembly. A shroud and a
wire guard provide protection from the rotating fan. See
Fig. 61. The exposed end of the fan motor shaft is protected
from weather by grease. If fan motor must be removed for
service or replacement, be sure to regrease fan shaft and
reinstall fan guard. The fan motor has a step in the motor shaft.
For proper performance, fan should be positioned such that it is
securely seated on this step. Tighten the bolt to 15 ft lb ± 2.0
(20.34 Nm ± 2.7 Nm) .
Refrigerant Circuit
LEAK TESTING — Units are shipped with complete operating charge of refrigerant R-134a (see Physical Data tables
supplied in the 30XA installation instructions) and should be
under sufficient pressure to conduct a leak test. If there is no
pressure in the system, introduce enough nitrogen to search for
the leak. Repair the leak using good refrigeration practices.
After leaks are repaired, system must be evacuated and
dehydrated.
REFRIGERANT CHARGE — Refer to Physical Data tables
supplied in the 30XA installation instructions). Immediately
ahead of filter drier in each circuit is a factory-installed liquid
line service valve. Each valve has a 1/4-in. access connection
for charging liquid refrigerant.
Charging with Unit Off and Evacuated — Close liquid line
service valve before charging. Weigh in charge shown on unit
nameplate. Open liquid line service valve; start unit and allow
it to run several minutes fully loaded. Check for a clear sight
glass. Be sure clear condition is liquid and not vapor.
Charging with Unit Running — If charge is to be added while
unit is operating, all condenser fans and compressors must be
operating. It may be necessary to block condenser coils at low
ambient temperatures to raise condensing pressure to approximately 198 psig (1365 kPa) to turn all condenser fans on. Do not
totally block a coil to do this. Partially block all coils in uniform
pattern. Charge each circuit until sight glass shows clear liquid,
and has a liquid line temperature of 103 F (39 C) for 30XA080352 units and 108 F (42 C) for 30XA400-500 units.
Add 3 to 5 lb (1.36 to 2.27 kg) depending on unit size of liquid charge into the fitting located on the tube entering the cooler. This fitting is located between the electronic expansion
valve (EXV) and the cooler.
Allow the system to stabilize and then recheck the liquid
temperature. If needed, add additional liquid charge, 3 to 5 lb
at a time, allowing the system to stabilize between each charge
addition. Slowly add charge as the sight glass begins to clear to
avoid overcharging.
CAUTION
Harsh chemicals, household bleach or acid or basic cleaners should not be used to clean outdoor or indoor coils of
any kind. These cleaners can be very difficult to rinse out
of the coil and can accelerate corrosion at the fin/tube interface where dissimilar materials are in contact. If there is
dirt below the surface of the coil, use the Totaline environmentally sound coil cleaner as described above.
CAUTION
High velocity water from a pressure washer, garden hose,
or compressed air should never be used to clean a coil. The
force of the water or air jet will bend the fin edges and
increase airside pressure drop. Reduced unit performance
or nuisance unit shutdown may occur.
Totaline Environmentally Sound Coil Cleaner Application
Instructions
1. Proper eye protection such as safety glasses is recommended during mixing and application.
2. Remove all surface loaded fibers and dirt with a vacuum
cleaner as described above.
3. Thoroughly wet finned surfaces with clean water and a
low velocity garden hose, being careful not to bend fins.
4. Mix Totaline environmentally sound coil cleaner in a
21/2 gallon garden sprayer according to the instructions
included with the cleaner. The optimum solution temperature is 100 F.
NOTE: Do NOT USE water in excess of 130 F (54.4 C), as the
enzymatic activity will be destroyed.
5. Thoroughly apply Totaline environmentally sound coil
cleaner solution to all coil surfaces including finned area,
tube sheets and coil headers.
6. Hold garden sprayer nozzle close to finned areas and
apply cleaner with a vertical, up-and-down motion. Avoid
spraying in horizontal pattern to minimize potential for
fin damage.
IMPORTANT: When adjusting refrigerant charge, circulate fluid through cooler continuously to prevent freezing
and possible damage to the cooler. Do not overcharge, and
never charge liquid into the low-pressure side of system.
86
FORMED METAL
MOUNT
FAN DECK
WIRE GUARD
MOTOR
FAN BLADE
a30-4249
Fig. 61 — Fan Mounting
Safety Devices — The 30XA chillers contain many
IMPORTANT: If unit is installed in an area where
ambient temperatures fall below 32 F (0° C), a suitable corrosion-inhibited antifreeze solution or cooler
heater must be used in the chilled water circuit.
safety devices and protection logic built into the electronic
control. Following is a description of the major safeties.
COMPRESSOR PROTECTION
Motor Overload — The compressor protection modules
(CPM) protect each compressor against overcurrent. Do not
bypass the current transformers or make any changes to the
factory-installed and configured headers. The configuration of
these headers defines the Must Trip Amps (MTA) at which the
CPM will turn the compressors off. Determine the cause for
trouble and correct the problem before resetting the CPM. See
Appendix D for MTA settings and configuration headers.
Each CPM board also reads the status of each compressor’s
high-pressure switch. All compressors have factory-installed
high-pressure switches. See Table 56.
Relief Devices — Fusible plugs are located in each cir-
cuit between the condenser and the liquid line shutoff valve.
PRESSURE RELIEF VALVES — Valves are installed in each
circuit and are located on the coolers and oil separators. These
valves are designed to relieve if an abnormal pressure condition
arises. Relief valves on all coolers relieve at 220 psi (1517 kPa).
Relief valves on oil separators relieve at 350 psi (2413 kPa).
These valves should not be capped. If a valve relieves, it should
be replaced. If the valve is not replaced, it may relieve at a lower
pressure, or leak due to trapped dirt from the system which may
prevent resealing.
See Table 57. Some local building codes require that relieved gases be exhausted to a specific location. This connection allows conformance to this requirement.
Table 56 — High-Pressure Switch Settings
UNIT
30XA
SWITCH SETTING
psig
kPa
304.5 +7.25, –14.5
2099 +50, –100
Table 57 — Relief Valve Connection Specs
If the switch opens during operation, the compressor will be
shut down. The CPM will reset automatically when the switch
closes, however, a manual reset of the control is required to
restart the compressor.
OIL SEPARATOR HEATERS — Each oil separator circuit
has a heater mounted on the underside of the vessel. The heater
is deenergized anytime the compressor is on. If the compressor
is off and outdoor-air temperature (OAT) is greater than 100 F
(37.8 C) the heater is deenergized. The heater will also be
deenergized if OAT – SST >32 F (17.8° C) and the OAT –
LWT > 32 F (17.8° C).
COOLER PROTECTION
Low Water Temperature — Microprocessor is programmed
to shut the chiller down if the leaving fluid temperature drops
below 34 F (1.1 C) for water or more than 8 F (4.4 C) below
set point for Fluid Type = brine. When the fluid temperature
rises 6 F (3.3 C) above the leaving fluid set point, the safety
resets and the chiller restarts. Reset is automatic as long as this
is the first occurrence of the day.
LOCATION
Oil Separator
DX Cooler Option
Flooded Cooler Option
CONNECTION SIZES
3/8 SAE Flare
5/8 SAE Flare
3/4 in. NPT Female
MAINTENANCE
Recommended Maintenance Schedule — The fol-
lowing are only recommended guidelines. Jobsite conditions
may dictate that maintenance schedule is performed more often
than recommended.
Routine:
For machines with e-coat condenser coils:
• Check condenser coils for debris; clean as necessary with
Carrier approved coil cleaner.
• Periodic clean water rinse, especially in coastal and industrial applications.
87
reset the alarm. The following method must be followed to
reset manual alarms:
Before resetting any alarm, first determine the cause of the
alarm and correct it. To reset the alarm, set R.ALM to YES.
The alarms will be reset. Indicator light will be turned off when
switched correctly. Do not reset the chiller at random without
first investigating and correcting the cause(s) of the failure.
Each alarm is described by a three or four-digit code. The
first one or two digits indicate the alarm source and are listed in
Fig. 62. The last two digits pinpoint the problem. See Table 59.
Every month:
• Check condenser coils for debris; clean as necessary with
Carrier approved coil cleaner.
• Check moisture indicating sight glass for possible refrigerant loss and presence of moisture.
Every 3 months (for all machines):
• Check refrigerant charge.
• Check all refrigerant joints and valves for refrigerant leaks;
repair as necessary.
• Check chilled water flow switch operation.
• Check all condenser fans for proper operation.
• Check oil filter pressure drop.
• Check oil separator heater operation.
• Inspect pump seal, if equipped with a hydronic pump package.
Every 12 months (for all machines):
• Check all electrical connections; tighten as necessary.
• Inspect all contactors and relays; replace as necessary.
• Check accuracy of thermistors; replace if greater than ±2° F
(1.2° C) variance from calibrated thermometer.
• Check accuracy of transducers; replace if greater than ±5 psi
(34.47 kPa) variance.
• Check to be sure that the proper concentration of antifreeze
is present in the chilled water loop, if applicable.
• Verify that the chilled water loop is properly treated.
• Check refrigerant filter driers for excessive pressure drop;
replace as necessary.
• Check chilled water strainers, clean as necessary.
• Check cooler heater operation.
• Check condition of condenser fan blades and that they are
securely fastened to the motor shaft.
• Perform Service Test to confirm operation of all components.
• Check for excessive cooler approach (Leaving Chilled
Water Temperature – Saturated Suction Temperature) which
may indicate fouling. Clean cooler vessel if necessary.
• Obtain oil analysis; change as necessary.
Alarm Descriptor
Alarm
.01
th
Alarm Prefix
A1 – Compressor A1 Failure
B1 – Compressor B1 Failure
C1 – Compressor C1 Failure
Co – Communication Failure
FC – Factory Configuration Error
MC – Master Chiller Configuration Error
P – Process Failure
Pr – Pressure Transducer Failure
Sr – Service Notification
th – Thermistor Failure
Alarm Suffix
Code Number to identify source
a30-4250
Fig. 62 — Alarm Description
DIAGNOSTIC ALARM CODES AND POSSIBLE
CAUSES
Thermistor Failure
Alarm 1 — Cooler Fluid Entering (th.01)
Alarm 2 — Cooler Fluid Leaving (th.02)
Criteria for Trip — This alarm criterion is tested whether the
unit is on or off if the temperature as measured by the thermistor is outside of the range –40 to 245 F (–40 to 118.3 C).
Action to be Taken — The unit shuts down normally, or is not
allowed to start.
Reset Method — Automatic, the alarm will reset once the
thermistor reading is within the expected range.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to the Main Base Board
• sensor accuracy
See the Thermistors section on page 71 for thermistor description, identifiers and connections.
Defrost Thermistor Failure
Alarm 3 — Circuit A (th.03)
Alarm 4 — Circuit B (th.04)
NOTE: These alarms are not used or supported. If this condition is encountered, confirm machine configuration.
TROUBLESHOOTING
See Table 58 for an abbreviated list of symptoms, possible
causes and possible remedies.
Alarms and Alerts — The integral control system constantly monitors the unit and generates warnings when abnormal or fault conditions occur. Alarms may cause either a circuit
(Alert) or the whole machine (Alarm) to shut down. Alarms
and Alerts are assigned codes as described in Table 59. The
alarm/alert indicator LED on the Navigator™ module is illuminated when any alarm or alert condition is present. If an
Alert is active, the Alarm Indicator LED will blink. If an Alarm
is active, the Alarm Indicator LED will remain on. Currently
active Alerts and Alarms can be found in (Current Alarm,
ALRM).
The controller generates two types of alarms. Automatic
reset alarms will reset without any intervention if the condition
that caused the alarm corrects itself. Manual reset alarms
require the service technician to check for the alarm cause and
88
Table 58 — Troubleshooting
SYMPTOM
Unit Does Not Run
POSSIBLE CAUSE
Check for power to unit
Wrong or incorrect unit
configuration
Active alarm
Active operating mode
Unit Operates too
Long or
Continuously
Low refrigerant charge
Compressor or control
contacts welded
Air in chilled water loop
Non-condensables in
refrigerant circuit.
Inoperative EXV
Load too high
Circuit Does Not Run Active alarm
Active operating mode
Circuit Does Not
Load
Active alarm
Active operating mode
Low saturated suction
temperature
High circuit suction superheat
Low suction superheat
Compressor Does
Not Run
Active alarm
Active operating mode
Inoperative compressor
contactor
Chilled Water Pump
is ON, but the
Machine is OFF
Cooler freeze protection
POSSIBLE REMEDY
• Check overcurrent protection device.
• Check non-fused disconnect (if equipped).
• Restore power to unit.
Check unit configuration.
Check Alarm status. See the Alarms and Alerts section
and follow
troubleshooting instructions.
Check for Operating Modes. See the Operating Modes
section and follow troubleshooting instructions
Check for leak and add refrigerant.
Replace contactor or relay.
Purge water loop.
Remove refrigerant and recharge.
• Check EXV, clean or replace.
• Check EXV cable, replace if necessary.
• Check EXV board for output signal.
Unit may be undersized for application
Check Alarm status. See the Alarms and Alerts section
and follow troubleshooting instructions.
Check for Operating Modes. See the Operating Modes
section and follow troubleshooting instructions.
Check Alarm status. See the Alarms and Alerts section
and follow troubleshooting instructions.
Check for Operating Modes. See the Operating Modes
section and follow troubleshooting instructions.
See Operating Modes 21, 22 and 23.
The circuit capacity is not allowed increase if circuit superheat is greater than 36°F (20 C). See Alarms 59-61 for
potential causes.
The circuit capacity is not allowed to increase if the circuit
superheat is less than 18° F (10° C). See Alarms 62-64 for
potential causes.
Check Alarm status. See the Alarms and Alerts section
and follow troubleshooting instructions.
Check for Operating Modes. See the Operating Modes
section and follow troubleshooting instructions.
• Check control wiring.
• Check scroll protection module.
• Check contactor operation, replace if necessary.
Chilled water loop temperature too low. Check cooler
heater.
LEGEND
EXV — Electronic Expansion Valve
89
Table 59 — Alarm Codes
PREFIX
CODE
th
SUFFIX
CODE
01
02
Pr
CCN
CPM
DX
EMM
EWT
EXV
HGBP
—
—
—
—
—
—
—
ALARM
ALARM DESCRIPTION
NUMBER
1
Cooler Entering Fluid
Thermistor
2
Cooler Leaving Fluid
Thermistor
03
04
06
3
4
5
Circuit A Defrost Thermistor
Circuit B Defrost Thermistor
Condenser Entering
Fluid Thermistor
Condenser Leaving
Fluid Thermistor
Reclaim Condenser
Entering Thermistor
Reclaim Condenser
Leaving Thermistor
OAT Thermistor
07
6
08
7
09
8
10
9
11
10
Master/Slave Common Fluid
Thermistor
12
11
13
12
14
13
15
14
16
15
17
16
18
17
19
18
Circuit A Suction Gas
Thermistor
Circuit B Suction Gas
Thermistor
Circuit C Suction Gas
Thermistor
Circuit A Discharge Gas
Thermistor
Circuit B Discharge Gas
Thermistor
Circuit C Discharge Gas
Thermistor
Circuit A Condenser Subcooling Liquid Thermistor
Circuit B Condenser Subcooling Liquid Thermistor
21
19
Space Temperature
Thermistor
23
20
Cooler heater feedback
thermistor
24
21
25
22
26
23
01
24
02
25
03
26
04
05
06
07
27
28
29
30
08
31
Circuit A Economizer Gas
Thermistor
Circuit B Economizer Gas
Thermistor
Circuit C Economizer Gas
Thermistor
Circuit A Discharge
Transducer
Circuit B Discharge
Transducer
Circuit C Discharge
Transducer
Circuit A Suction Transducer
Circuit B Suction Transducer
Circuit C Suction Transducer
Circuit A Reclaim Pumpdown Pressure Transducer
Circuit B Reclaim Pumpdown Pressure Transducer
LEGEND
Carrier Comfort Network®
HPS
Compressor Protection Module
LWT
Direct Expansion
MOP
Energy Management Module
MTA
Entering Water Temperature
OAT
Electronic Expansion Valve
SST
Hot Gas Bypass
UL
—
—
—
—
—
—
—
ACTION TAKEN
BY CONTROL
Unit be shut down or
not allowed to start
RESET
TYPE
Automatic
None
Automatic
Configuration error
Temperature measured
by the controller is
outside of the range
of –40 F to 245 F
(–40 C to 118 C)
Temperature measured
by the controller is
outside of the range
of –40 F to 245 F
(–40 C to 118 C)
Temperature measured
by the controller is
outside of the range
of –40 F to 245 F
(–40 C to 118 C)
Unit be shut down or
not allowed to start
Automatic
Faulty Sensor,
wiring error or failed
main base board
Automatic
Faulty Sensor,
wiring error, failed
EXV or CPM board
Temperature measured
by the controller is
outside of the range
of –40 F to 245 F
(–40 C to 118 C)
Temperature measured
by the controller is
outside of the range
of –40 F to 245 F
(–40 C to 118 C)
Temperature measured
by the controller is
outside of the range
of –40 F to 245 F
(–40 C to 118 C)
Temperature measured
by the controller is
outside of the range
of –40 F to 245 F
(–40 C to 118 C)
None
Automatic
Configuration error
Alarm tripped
Automatic
Faulty Sensor, wiring
error, failed EMM
board
None
Automatic
Configuration error
Circuit economizer
function disabled
Automatic
Faulty Sensor,
wiring error, failed
EXV board
Measured voltage is
Circuit shut down or
0 vdc or SST > EWT and not allowed to start
EXV < 50% for 1 minute
Automatic
Faulty transducer,
wiring error, failed
main base board or
fan board
Measured voltage is
0 vdc or SST > EWT and
EXV < 50% for 1 minute
Automatic
Configuration error
REASON FOR ALARM
Temperature measured
by the controller is
outside of the range
of –40 F to 245 F
(–40 C to 118 C)
Temperature measured
by the controller is
outside of the range
of –40 F to 245 F
(–40 C to 118 C)
High Pressure Switch
Leaving Water Temperature
Maximum Operating Pressure
Must Trip Amps
Outdoor Air Temperature
Saturated Suction Temperature
Underwriters Laboratories
90
Dual chiller deactivated. Master and
slave machines
operate in standalone mode
Circuit shut down or
not allowed to start
None
PROBABLE CAUSE
Faulty Sensor,
wiring error or failed
main base board
Table 59 — Alarm Codes (cont)
PREFIX
CODE
Pr
SUFFIX
CODE
10
11
12
13
14
15
Co
P
CCN
CPM
DX
EMM
EWT
EXV
HGBP
—
—
—
—
—
—
—
ALARM
ALARM DESCRIPTION
NUMBER
32
Circuit A Oil Pressure
Transducer
33
Circuit B Oil Pressure
Transducer
34
Circuit C Oil Pressure
Transducer
35
Circuit A Economizer
Pressure Transducer
36
Circuit B Economizer
Pressure Transducer
37
Circuit C Economizer
Pressure Transducer
A1
38
B1
39
C1
40
E1
41
E2
42
E3
43
F1
44
F2
ACTION TAKEN
BY CONTROL
Measured voltage is
Circuit shut down or
0 vdc or SST > EWT and not allowed to start
EXV < 50% for 1 minute
REASON FOR ALARM
RESET
TYPE
PROBABLE CAUSE
Automatic
Faulty transducer,
wiring error, failed CPM
board
Faulty transducer,
wiring error, failed CPM
board
Wrong CPM address,
wrong unit configuration, wiring error, power
loss, failed
CPM board
Measured voltage is
0 vdc
Circuit shut down or
not allowed to start
Automatic
Loss of communication with
Compressor Board A
Loss of communication with
Compressor Board B
Loss of communication with
Compressor Board C
Loss of communication with
EXV Board A
Loss of communication with
EXV Board B
Loss of communication with
EXV Board C
Loss of communication with
Fan Board 1
No communication
with CPM board
Affected
compressor shut
down
Automatic
No communication with
EXV board
Affected
compressor
shut down
Automatic
Wrong EXV board
address, wrong unit
configuration, wiring
error, power loss,
failed EXV board
No communication with
fan board
Automatic
Wrong board address,
wrong unit configuration, wiring error, loss
of power, failed board
45
Loss of communication with
Fan Board 2
No communication with
fan board
Circuit A/B shut
down or not allowed
to start (080-120
ton), Circuit A shut
down or not allowed
to start
(130-500 ton)
Circuit B shut down
or not allowed to
start (130-500 ton)
Automatic
F3
46
Loss of communication with
Fan Board 3
No communication with
fan board
Circuit C shut down
or not allowed to
start (400-500 ton)
Automatic
01
47
No communication with
free cooling board
None
Automatic
02
48
03
49
Loss of communication with
Free Cooling Board 1
Loss of communication with
Free Cooling Board 2
Loss of communication with
Energy Management Board
Wrong board address,
wrong unit configuration, wiring error, loss
of power, failed board
Wrong board address,
wrong unit configuration, wiring error, loss
of power, failed board
Configuration error
No communication with
EMM board
Automatic
Wrong board
address, wrong unit
configuration, wiring
error, power loss to
module, failed module
04
50
Disable or not allow
EMM functions
3 step and 4-20 mA
and space temperature reset, occupancy override and
ice build)
None
Automatic
Configuration error
05
51
01
52
02
53
03
54
04
55
Loss of communication with
Heat Reclaim Board
Loss of communication with
AUX Board 6
No communication
with Free Cooling Board
Wrong board
address, wrong unit
configuration, wiring
error, power loss to
module, failed module
Cooler Freeze Protection
Entering or leaving therm- Unit shut down or Automatic, first Faulty thermistor, faulty
istor sensed a tempera- not allowed to start occurrence in wiring, low water flow,
ture at or below freeze
24 hours;
low loop volume, fouled
point
manual if
cooler, or freeze
multiple alarms
conditions
within 24 hours
Condenser Freeze Protection
—
None
Automatic
Configuration error
Circuit A
Condenser Freeze Protection
Circuit B
Condenser Freeze Protection
Circuit C
LEGEND
Carrier Comfort Network®
HPS
Compressor Protection Module
LWT
Direct Expansion
MOP
Energy Management Module
MTA
Entering Water Temperature
OAT
Electronic Expansion Valve
SST
Hot Gas Bypass
UL
—
—
—
—
—
—
—
No communication
with HGBP/PUMP Board
High Pressure Switch
Leaving Water Temperature
Maximum Operating Pressure
Must Trip Amps
Outdoor Air Temperature
Saturated Suction Temperature
Underwriters Laboratories
91
Unit shut down or
not allowed to start
Automatic
Table 59 — Alarm Codes (cont)
PREFIX SUFFIX
CODE
CODE
P
05
06
07
08
09
10
11
12
13
14
ALARM
REASON FOR ALARM
NUMBER ALARM DESCRIPTION
56
Circuit A Low Suction
Low saturated suction temTemperature
peratures detected for a
period of time
57
Circuit B Low Suction
Temperature
58
Circuit C Low Suction
Temperature
59
Circuit A High Suction
EXV>98%,
Superheat
suction superheat > 30 F
(–1 C), and SST<MOP for
60
Circuit B High Suction
more than 5 minutes
Superheat
61
Circuit C High Suction
Superheat
62
Circuit A Low Suction
EXV<5% and either the sucSuperheat
tion superheat is less than
the set point by at least 5 F
63
Circuit B Low Suction
(–15 C) or the suction temSuperheat
perature is greater than
64
Circuit C Low Suction
MOP set point for more than
Superheat
5 minutes
65
Interlock Failure
Lockout Switch Closed
RESET
PROBABLE CAUSE
TYPE
Automatic, first Faulty thermistor, faulty wiroccurrence in 24 ing, low water flow, low loop
hours;
volume, fouled cooler, or
manual if
freeze conditions.
multiple alarms
Closed suction valve, DX
within 24 hours
units.
Circuit shut down
Manual
Faulty transducer, faulty wiring, faulty thermistor, faulty
EXV, low refrigerant charge,
plugged or restricted liquid
line
Circuit shut down
Manual
Faulty transducer, faulty wiring, faulty thermistor, faulty
EXV, or incorrect
configuration
Automatic
Lockout Switch Closed
on EMM board
Automatic
External pump off. Faulty
jumper wiring when channel
not used
Faulty communication wiring, no power supply to the
external controller
Unit shut down or
not allowed to
start
External pump interlock
Unit shut down or
open
not allowed to
start
Loss of communication with
Unit change to
an external control device
stand-alone
for more than
operation
2 minutes
Communication between the Unit change to
master and slave machines
stand-alone
lost
operation
28
66
29
67
30
68
Master/Slave communication Failure
67
69
70
Oil pressure and suction
pressure differential is less
than the set point
Circuit shut down
68
69
71
Automatic, first
occurrence in 24
hours;
manual if
multiple alarms
within 24 hours
70
72
Manual
73
Plugged oil filter, closed oil
valve, bad oil solenoid, oil
check valve stuck, faulty oil
pressure transducer
72
74
Difference between discharge pressure and oil
pressure is greater than
50 psi for more than
30 seconds
Circuit shut down
71
84
75
Manual
Plugged oil filter
76
86
77
Difference between discharge pressure and oil
pressure is greater than
30 psi for more than
5 minutes
Alert generated
85
75
76
77
78
79
80
Circuit A Low Oil
Pressure
Circuit B Low Oil
Pressure
Circuit C Low Oil
Pressure
Circuit A Max Oil Filter
Differential Pressure
Circuit B Max Oil Filter
Differential Pressure
Circuit C Max Oil Filter
Differential Pressure
Circuit A High Oil Filter
Drop Pressure
Circuit B High Oil Filter
Drop Pressure
Circuit C High Oil Filter
Drop Pressure
Circuit A Low Oil Level
Circuit B Low Oil Level
Circuit C Low Oil Level
Oil level switch open
Circuit shut down
or not allowed to
start
MC
nn
81
Wrong or incompatible configuration data
FC
n0
82
Master chiller configuration error Number 01 to
nn
No factory configuration
nn
83
31
84
Illegal factory configuration Number 01 to 04
Unit is in CCN emergency stop
Wrong or incompatible configuration data
Emergency stop command
has been received
32
33
85
86
Cooler pump #1 fault
Cooler pump #2 fault
15
87
Condenser Flow Switch
Failure
Pump interlock status does
not match pump
status
—
P
CCN
CPM
DX
EMM
EWT
EXV
HGBP
—
—
—
—
—
—
—
Electrical Box Thermostat Failure/Reverse
Rotation
Loss of communication
with System Manager
ACTION TAKEN
BY CONTROL
Circuit shut down
LEGEND
Carrier Comfort Network®
HPS
Compressor Protection Module
LWT
Direct Expansion
MOP
Energy Management Module
MTA
Entering Water Temperature
OAT
Electronic Expansion Valve
SST
Hot Gas Bypass
UL
No Configuration
—
—
—
—
—
—
—
Automatic
Faulty communication wiring, no power or control
power to the main base
board of either module
Plugged oil filter, faulty oil
transducer, oil check valve
stuck, plugged oil strainer
Automatic, first
Low oil level, faulty switch,
occurrence in 24
wiring error, failed CPM
hours; manual if
board
multiple alarms
within 24 hours
Unit not allowed to
Automatic
Configuration error
start in Masterslave control
Unit not allowed to
Automatic
Configuration error
start
Unit not allowed to
Automatic
Configuration error
start
(see Table 61)
Unit shut down or
Automatic
Carrier Comfort
not allowed to
Network® Emergency Stop
command received
start
Unit shuts down, if
Manual
Faulty contacts, wiring error
available, another
or low control voltage. Conpump will start
figuration error.
None
Manual
Configuration error
High Pressure Switch
Leaving Water Temperature
Maximum Operating Pressure
Must Trip Amps
Outdoor Air Temperature
Saturated Suction Temperature
Underwriters Laboratories
92
Automatic
Table 59 — Alarm Codes (cont)
PREFIX
CODE
P
SUFFIX
CODE
34
35
37
38
39
40
41
42
43
73
74
78
79
80
81
82
83
87
88
89
90
91
ALARM
ALARM DESCRIPTION
REASON FOR ALARM
NUMBER
88
Circuit A Reclaim Operation
—
Failure
89
Circuit B Reclaim Operation
Failure
90
Circuit A — Repeated high
Multiple capacity overdischarge gas overrides
rides due to high
saturated discharge
91
Circuit B — Repeated high
temperature
discharge gas overrides
92
Circuit C — Repeated high
discharge gas overrides
93
Circuit A — Repeated low
Multiple capacity
suction temp overrides
overrides due to low saturated
suction temperature
94
Circuit B — Repeated low
suction temp overrides
95
Circuit C — Repeated low
suction temp overrides
96
Low entering water temperaNot supported
ture in heating
97
Condenser pump #1 default
—
98
Condenser pump #2 default
99
Circuit A High Discharge
Discharge gas temperaTemperature
ture is higher than 212 F
(100 C) for more than
100
Circuit B High Discharge
90 seconds
Temperature
101
Circuit C High Discharge
Temperature
102
Circuit A Low Economizer
The economizer pressure
Pressure
is below the suction pressure more than 14.5 psi
103
Circuit B Low Economizer
for more than 10 seconds
Pressure
104
Circuit C Low Economizer
Pressure
105
Circuit A Slide Valve Control
If 100% load current is
Unverifiable
less than 1.1 times of 30%
106
Circuit B Slide Valve Control load current, or for 1 minute when active cooling
Unverifiable
setpoint is greater than
107
Circuit C Slide Valve Control
32 F (0°C).
Unverifiable
108
Cooler flow switch set point
—
configuration failure
109
Cooler flow switch failure
Flow switch open
97
127
Water Exchanger Temperature Sensors Swapped
Service maintenance alert
Number # nn
Sr
nn
110
A1, B1, C1
01
111-01,
112-01,
113-01
Compressor Motor temperature too high
02
111-02,
112-02,
113-02
Compressor Motor temperature out of range
03
111-03,
112-03,
113-03
Compressor High pressure
switch protection
Control detects EWT
below LWT for 1 minute
Field programmed
elapsed time has expired
for maintenance time
Compressor temperature
higher than 232 F (111 C)
for more than 90 seconds
Compressor temperature
reading out of the range of
–40 F to 245 F
(–40 C to 118 C)
HPS input on CPM board
open
LEGEND
CCN
CPM
DX
EMM
EWT
EXV
HGBP
—
—
—
—
—
—
—
Carrier Comfort Network®
Compressor Protection Module
Direct Expansion
Energy Management Module
Entering Water Temperature
Electronic Expansion Valve
Hot Gas Bypass
HPS
LWT
MOP
MTA
OAT
SST
UL
—
—
—
—
—
—
—
High Pressure Switch
Leaving Water Temperature
Maximum Operating Pressure
Must Trip Amps
Outdoor Air Temperature
Saturated Suction Temperature
Underwriters Laboratories
93
ACTION TAKEN
BY CONTROL
None
RESET
TYPE
Manual
Circuit shut down
Automatic
Condenser air
recirculation, dirty or
plugged condenser
coils, inaccurate
discharge transducer,
faulty condenser fan
Circuit shut down
Automatic
Inaccurate
transducer, faulty EXV,
low refrigerant charge,
plugged or restricted
liquid line filter drier.
—
—
—
None
Manual
Configuration error
Circuit shut down
Manual
Faulty transducer/high
pressure switch, low/
restricted condenser
flow
Circuit shut down
Manual
Faulty transducer,
faulty main base board,
faulty wiring, closed
suction service valve,
faulty EXV
None
Manual
Slide valve stuck, inaccurate initial current
reading
None
Manual
Configuration error
Unit shut down
Unit shut down
None
Configuration error
Manual if unit Faulty flow switch, low
is running,
cooler flow, faulty
automatic
wiring, faulty cooler
otherwise
pump, faulty main base
board, minutes off time
set to 0
Manual
Wiring error, EWT and
LWT sensors swapped
Manual
Maintenance required
Circuit shut down
Manual
Circuit shut down
Manual
Circuit shut down
PROBABLE CAUSE
Motor cooling solenoid
or economizer
(080,082 only) EXV
failure, faulty CPM
board, low refrigerant
charge (090-500)
Faulty thermistor, faulty
wiring, faulty CPM
board
Manual, press Loss of condenser air
reset button on flow, operation beyond
HPS
compressor envelope,
faulty high pressure
switch, faulty wiring,
faulty CPM board
Table 59 — Alarm Codes (cont)
PREFIX
SUFFIX
CODE
CODE
A1, B1, C1
04
05
06
RESET
TYPE
Manual
Circuit shut down
Manual
CPM board detects current unbalance greater
than 65% for more than
1 second
Circuit shut down
Manual
CPM board detects high
motor current compared
with MTA setting
CPM board detects locked
rotor current compared
with MTA setting
PROBABLE CAUSE
Operating beyond
compressor envelope,
incorrect configuration
Compressor motor failure, unloader slide
valve failure, compressor mechanical failure
Blown fuse, wiring
error, loose terminals
Compressor Phase loss L1
Compressor Low current
alarm
CPM detects motor current less than a certain
percentage of the MTA
setting, compressor not
operating
Circuit shut down
Manual
10
111-10,
112-10,
113-10
Compressor Y delta starter
current increase failure alarm
If the delta mode current
is not 25% greater than
the current in Y mode
Circuit shut down
Manual
11
111-11,
112-11,
113-11
Compressor Contactor failure
Circuit shut down
Manual
12
111-12,
112-12,
113-12
Compressor Unable to stop
motor
Circuit shut down
Manual
Faulty contactor,
contactor welded,
wiring error
13
111-13,
112-13,
113-13
Compressor Phase reversal
CPM board detects
greater than 15% of MTA
current for 10 seconds
after shutting off the compressor contactor. Oil
solenoid is energized.
CPM board detects
greater than 15% of MTA
current for 10 seconds
after three attempts
CPM board detects phase
reversal from current
toroid
Circuit shut down
Manual
14
111-14,
112-14,
113-14
111-15,
112-15,
113-15
Compressor MTA configuration fault
MTA setting is out of the
allowed MTA range
Circuit shut down
Manual
Terminal block power
supply lead not in
correct phase. Power
supply leads going
through toroid crossed
Incorrect MTA setting,
faulty CPM board
Compressor Configuration
switch mismatch
CPM board MTA setting
do not match factory
configuration
Circuit shut down
Manual
111-16,
112-16,
113-16
111-17,
112-17,
113-17
111-18,
112-18,
113-18
111-19,
112-19,
113-19
Compressor Unexpected
switch setting change
CPM board dipswitch S1
setting changed
Circuit shut down
Manual
Compressor Power on reset
CPM board detects a
power failure
Circuit shut down
Manual
Compressor UL 1998 critical
section software error
Software error
Circuit shut down
Manual
Electric noise, faulty
CPM board
Compressor UL 1998 current
measure dual channel
mismatch
Software error
Circuit shut down
Manual
Electric noise, faulty
CPM board
08
09
15
16
17
18
19
—
—
—
—
—
—
—
ACTION TAKEN
BY CONTROL
Circuit shut down
REASON FOR ALARM
111-06,
112-06,
113-06
111-07,
112-07,
113-07
111-08,
112-08,
113-08
111-09,
112-09,
113-09
07
CCN
CPM
DX
EMM
EWT
EXV
HGBP
ALARM
ALARM DESCRIPTION
NUMBER
111-04, Compressor Over current
112-04,
113-04
111-05, Compressor Locked rotor
112-05,
113-05
Compressor Phase loss L2
Compressor Phase loss L3
LEGEND
Carrier Comfort Network®
HPS
Compressor Protection Module
LWT
Direct Expansion
MOP
Energy Management Module
MTA
Entering Water Temperature
OAT
Electronic Expansion Valve
SST
Hot Gas Bypass
UL
—
—
—
—
—
—
—
High Pressure Switch
Leaving Water Temperature
Maximum Operating Pressure
Must Trip Amps
Outdoor Air Temperature
Saturated Suction Temperature
Underwriters Laboratories
94
Power supply disconnected, blown fuse,
wiring error, contact
deenergized, faulty
current toroid high
pressure switch trip.
Power supply to delta
contactor not
connected, faulty delta
contactor or wiring,
faulty CPM board
Faulty contactor, contactor welded, wiring
error
Incorrect CPM dipswitch setting,
incorrect factory MTA
setting, faulty CPM
board
Incorrect CPM dipswitch setting, faulty
CPM board
Power supply
interruption
See the Thermistors section on page 71 for thermistor description, identifiers and connections.
Circuit Discharge Gas Thermistor Sensor Failure
Alarm 14 — Circuit A (th.15)
Alarm 15 — Circuit B (th.16)
Alarm 16 — Circuit C (th.17)
Criteria for Trip — This alarm criterion is tested whether the
unit is ON or OFF. The alarm is tripped if the temperature
measured by the Outdoor Air Thermistor sensor is outside the
range of –40 to 245 F (–40 to 118.3 C).
Action to be Taken — The unit shuts down normally, or is not
allowed to start.
Reset Method — Automatic, the alarm will reset once the
thermistor reading is within the expected range.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to the CPM board
• a faulty thermistor
• a faulty channel on the board
See the Thermistors section on page 71 for thermistor description, identifiers and connections.
Condenser Subcooling Liquid Thermistor
Alarm 17 — Circuit A (th.18)
Alarm 18 — Circuit B (th.19)
NOTE: Alarms 17 and 18 are not used or supported. If this
condition is encountered, confirm machine configuration.
Alarm 19 — Space Temperature Sensor Failure (th.21)
Criteria for Trip — This alarm criterion is checked whether the
unit is ON or OFF and if Space Temperature Reset has been
enabled. This alarm is generated if the outdoor-air temperature
as measured by the thermistor is outside of the range –40 to
245 F (–40 to 118.3 C).
Action to be Taken — Unit operates under normal control.
Temperature Reset based on Space Temperature is disabled.
Reset Method — Automatic, once the thermistor reading is
within the expected range. The Space Temperature Reset will
resume once the alarm has cleared.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to the Energy Management Module
• board for a faulty channel
• a faulty thermistor
For thermistor descriptions, identifiers and connections, see
the Thermistors section.
Alarm 20 — Cooler Heater Feedback Sensor Thermistor
(th.23)
NOTE: Alarm 20 is not used or supported. If this condition is
encountered, confirm machine configuration.
Economizer Gas Thermistor
Alarm 21 — Circuit A (th.24)
Alarm 22 — Circuit B (th.25)
Alarm 23 — Circuit C (th.26)
Criteria for Trip — This alarm criterion is tested whether the
unit is ON or OFF. The alarm is tripped if the Economizer gas
reading is outside the range of –40 to 245 F (–40 to 118.3 C).
Action to be Taken — The unit shuts down normally, or is not
allowed to start.
Reset Method — Automatic, the alarm will reset once the
thermistor reading is within the expected range.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to the EXV board
• a faulty thermistor
• a faulty channel on the board
Thermistor Failure
Alarm 5 — Condenser Entering Fluid (th.06)
Alarm 6 — Condenser Leaving Fluid (th.07)
NOTE: These alarms are not used or supported. If this condition is encountered, confirm machine configuration.
Condenser Reclaim Thermistor
Alarm 7— Reclaim Entering Fluid (th.08)
Alarm 8 — Reclaim Leaving Fluid (th.09)
NOTE: Alarms 7 and 8 are not used or supported. If this condition is encountered, confirm machine configuration.
Alarm 9 — Outdoor Air Temperature Thermistor Failure
(th.10)
Criteria for Trip — This alarm criterion is tested whether the
unit is ON or OFF. The alarm is tripped if the temperature
measured by the outdoor air thermistor sensor is outside the
range of –40 to 245 F (–40 to 118.3 C).
Action to be Taken — The unit shuts down normally, or is not
allowed to start.
Reset Method — Automatic, the alarm will reset once the
thermistor reading is within the expected range.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to the Main Base Board
• a faulty thermistor
See the Thermistors section on page 71 for thermistor description, identifiers and connections.
Alarm 10 — Master/Slave Common Fluid Thermistor
(th.11)
Criteria for Trip — This alarm criterion is tested whether the
unit is ON or OFF. The alarm will be tripped if the unit is
configured as a master or a slave (Master/Slave Select,
MSSL), leaving temperature control is selected (Entering
Fluid Control, EWTO), and if the temperature measured by
the CHWS (chilled water sensor) fluid sensor is outside the
range of –40 to 245 F (–40 to 118.3 C).
Action to be Taken — Master/slave operation is disabled and
the chiller returns to stand alone mode.
Reset Method — Reset is automatic when the thermistor reading is inside the range of –40 to 245 F (–40 to 118.3 C).
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to the Main Base Board
• a faulty thermistor
See the Thermistors section on page 71 for thermistor description, identifiers and connections.
Suction Gas Thermistor
Alarm 11 — Circuit A (th.12)
Alarm 12 — Circuit B (th.13)
Alarm 13 — Circuit C (th.14)
Criteria for Trip — This alarm criterion is tested whether the
unit is ON or OFF. If the suction gas temperature as measured
by the thermistor is outside of the range –40 to 245 F (–40 to
118.3 C).
Action to be Taken — The affected circuit shuts down
normally.
Reset Method — Automatic, once the thermistor reading is
within the expected range. The affected circuit will restart once
the alarm has cleared.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to the EXV board
• board for a faulty channel
• a faulty thermistor
95
See the Thermistors section on page 71 for thermistor description, identifiers and connections.
Discharge Transducer
Alarm 24 — Circuit A (Pr.01)
Alarm 25 — Circuit B (Pr.02)
Alarm 26 — Circuit C (Pr.03)
Criteria for Trip — The criterion is tested whether the circuit is
ON or OFF. This alarm is generated if the voltage as sensed by
the MBB or Fan Board C (FBC) is 0 vdc, which corresponds
to the Navigator™ display of –7 psi (–48.3 kPa).
Action to be Taken — The circuit is shut down normally, or not
allowed to start.
Reset Method — Automatic, once the transducer voltage is
greater than 0 vdc, which corresponds to the Navigator display
of a value greater than –7 psi (–48.3 kPa).
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to Main Base Board (Alarms 24 and 25)
• sensor wiring to Fan Board C (Alarm 26)
• board for a faulty channel
• for a faulty transducer
• confirm unit configuration
Suction Pressure Transducer Failure
Alarm 27 — Circuit A (Pr.04)
Alarm 28 — Circuit B (Pr.05)
Alarm 29 — Circuit C (Pr.06)
Criteria for Trip — The criteria are tested whether the circuit is
ON or OFF. The alarm is generated if one of the following
criteria is met:
1. If the voltage as sensed by the MBB or Fan Board C is
0 vdc, which corresponds to the Navigator™ display of
–7 psi (–48.3 kPa).
2. The circuit is ON in cooling mode and the Saturated
Suction Temperature (Saturated Suction Temp, SST)
for the circuit is greater than the Entering Water Temperature and EXV opening is less than 50% for more than
60 seconds.
Action to be Taken — The circuit is shut down immediately, or
not allowed to start.
Reset Method
1. Automatic, once the transducer voltage is greater than
0 vdc, which corresponds to the Navigator display of a
value greater than –7 psi (–48.3 kPa).
2. Automatic once the circuit’s saturated suction temperature is lower than the Entering Water Temperature by 3° F
(1.6° C). If this criterion trips the alarm 3 times within a
24-hour period, the alarm changes to a manual reset.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to Main Base Board (Alarms 27 and 28)
• sensor wiring to Fan Board C (Alarm 29)
• board for a faulty channel
• faulty transducer
• faulty entering water temperature sensor
• unit configuration
Reclaim Pumpdown Pressure Transducer
Alarm 30 — Circuit A (Pr.07)
Alarm 31 — Circuit B (Pr.08)
NOTE: Alarms 30 and 31 are not used or supported. If this
condition is encountered, confirm machine configuration.
Oil Pressure Transducer
Alarm 32 — Circuit A (Pr.10)
Alarm 33 — Circuit B (Pr.11)
Alarm 34 — Circuit C (Pr.12)
Criteria for Trip — The criteria are tested whether the circuit is
ON or OFF. The alarm is generated if one of the following criteria is met:
1. If the voltage as sensed by the MBB or Fan Board C is
0 vdc, which corresponds to the Navigator display of
–7 psi (–48.3 kPa).
2. The circuit is OFF and outside air temperature is below
35.6 F (2 C).
3. The circuit is OFF and the fluid type is brine.
Action to be Taken — The circuit is shut down immediately, or
not allowed to start.
Reset Method — Automatic, once the transducer voltage is
greater than 0 vdc.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to CPM board
• board for a faulty channel
• faulty transducer
• plugged oil filter
• faulty oil solenoid valve coil
• stuck oil solenoid valve
• confirm unit configuration
Economizer Pressure Transducer Failure
Alarm 35 — Circuit A (Pr. 13)
Alarm 36 — Circuit B (Pr. 14)
Alarm 37 — Circuit C (Pr. 15)
Criteria for Trip — The criteria are tested whether the circuit is
ON or OFF. The alarm is generated if the voltage as sensed by
the MBB or Fan Board C is 0 vdc, which corresponds to the
Navigator display of –7 psi (–48.3 kPa).
Action to be Taken — The circuit is shut down immediately, or
not allowed to start.
Reset Method — Automatic, once the transducer voltage is
greater than 0 vdc, which corresponds to the Navigator display
of a value greater than –7 psi (–48.3 kPa).
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to EXV Board
• EXV board for a faulty channel
• faulty transducer
• faulty economizer EXV or EXV wiring
• faulty economizer EXV channel on the board
• closed or partially closed suction service valve
• confirm unit configuration
Loss of Communication with Compressor Board
Alarm 38 — Compressor Board A (Co.A1)
Alarm 39 — Compressor Board B (Co.B1)
Alarm 40 — Compressor Board C (Co.C1)
Criteria for Trip — The alarm criterion is tested whether the
unit is ON or OFF. If communication with the Compressor
Protection Module Board (CPM) is lost for a period of 10 seconds, the alarm will be generated.
Action to be Taken — The affected compressor will be shut
down.
Reset Method — Automatic, if communication is established.
If called for, the compressor will start normally.
Possible Causes — If this condition is encountered, check the
following items:
• power supply to the affected CPM board
• address of the CPM
• local equipment network (LEN) wiring
• confirm unit configuration
Loss of Communication with EXV Board
Alarm 41 — Circuit A, EXV Board A (Co.E1)
Alarm 42 — Circuit B, EXV Board B (Co.E2)
Alarm 43 — Circuit C, EXV Board C (Co.E3)
96
• confirm unit configuration
Loss of Communication with Free Cooling Board
Alarm 47 — Board 1 (Co.01)
Alarm 48 — Board 2 (Co.02)
NOTE: Alarms 47 and 48 are not used or supported. If this
condition is encountered, confirm machine configuration.
Alarm 49 — Loss of Communication with Energy Management Module Board (Co.03)
Criteria for Trip — The criterion is tested whether the unit is
ON or OFF and when a function that requires the Energy
Management Module (EMM) is configured. If communication
with the EMM is lost for a period of 10 seconds, the alarm will
be triggered.
Action to be Taken — If any function controlled by the EMM
(3-Step and 4-20 mA Demand Limit, 4-20 mA and Space
Temperature Reset, Occupancy Override, and Ice Build) is
active, that function will be terminated. If an EMM function is
programmed, and communication is lost, the function will not
be allowed to start.
Reset Method — Automatic, if communication is established,
the functions will be enabled.
Possible Causes — If this condition is encountered, check the
following items:
• The EMM is installed, (EMM NRCP2 Board, EMM). If
EMM NRCP2 Board, EMM=YES, then check for a control option that requires the EMM that may be enabled (correct configuration if not correct).
• power supply to EMM
• address of the EMM
• local equipment network (LEN) wiring
• confirm unit configuration to be sure that no options that
require the EMM are enabled
Alarm 50 — Loss of Communication with Heat Reclaim
Board (Co.04)
NOTE: Alarm 50 is not used or supported. If this condition is
encountered, confirm machine configuration.
Alarm 51 — Loss of Communication with AUX Board 6
(Co.05)
Criteria for Trip — The alarm criteria are checked whether the
unit is ON or OFF. If units are configured for dual cooler pump
control (Cooler Pumps Sequence, PUMP=2,3,4) or HGBP =
YES. If communication with the AUX board is lost then the
alarm will be generated.
Action to be Taken — Unit shut down or not allowed to start.
Reset Method — Automatic, if communication is established,
the unit will start normally.
Possible Causes — If this condition is encountered, check the
following items:
• power supply to the HGBP/PUMP board
• address of the HGBP/PUMP board
• local equipment network (LEN) wiring
• confirm network configuration
Alarm 52 — Cooler Freeze Protection (P.01)
Criteria for Trip — The alarm criteria are checked whether the
unit is ON or OFF. If the entering or leaving water thermistor
senses a temperature at the freeze point or less, the alarm will
be generated. For a fresh water system (Cooler Fluid Type,
FLUD=1), the freeze point is 34 F (1.1 C). For medium temperature brine systems (Cooler Fluid Type, FLUD=2), the
freeze point is Brine Freeze Set Point (Brine Freeze Setpoint,
LOSP).
Action to be Taken — Unit shut down or not allowed to start.
Chilled water pump will be started.
Reset Method — Automatic, first occurrence in 24 hours if
LWT rises to 6° F (3° C) above set point. Manual, if more than
one occurrence in 24 hours.
Criteria for Trip — The alarm criterion is tested whether the
unit is ON or OFF. If communication with EXVA, B or C is
lost for a period of 10 seconds, the alarm will be triggered.
Action to be Taken — If running, Circuit A, B or C will shut
down normally. If Circuit A, B or C is not operating, it will not
be allowed to start.
Reset Method — Automatic, if communication is established,
the unit will start normally.
Possible Causes — If this condition is encountered, check the
following items:
• power supply to EXVA, B or C
• address of the EXV board
• local equipment network (LEN) wiring
• confirm unit configuration
Alarm 44 — Loss of Communication with Fan Board 1
(Co.F1)
Criteria for Trip — The criterion is tested whether the unit is
ON or OFF. If communication with Fan Board A is lost for a
period of 10 seconds, the alarm will be triggered.
Action to be Taken — If the number of fans per circuit is
greater than four fans per circuit, Circuit A will shut down normally if they are running. Circuit B will continue to run. If the
circuit or circuits controlled by the board are not running, then
they will not be allowed to start.
Reset Method — Automatic, if communication is established,
the unit will start normally.
Possible Causes — If this condition is encountered, check the
following items:
• power supply to Fan Board A
• address of the Fan Board A
• local equipment network (LEN) wiring
• confirm unit configuration
Alarm 45 — Loss of Communication with Fan Board 2
(Co.F2)
Criteria for Trip — The criterion is tested whether the unit is
ON or OFF, and only if Circuit A or B has more than four fans
per circuit.
NOTE: Fan Board B controls Circuit B only.
Action to be Taken — If communication with Fan Board B is
lost for a period of 10 seconds, the alarm will be triggered. If
running, Circuit B will shut down normally. If Circuit B is not
running, then it will not be allowed to start.
Reset Method — Automatic, if communication is established,
the unit will start normally.
Possible Causes — If this condition is encountered, check the
following items:
• power supply to Fan Board B
• address of the Fan Board B
• local equipment network (LEN) wiring
• confirm unit configuration
Alarm 46 — Loss of Communication with Fan Board 3
(Co.F3)
Criteria for Trip — The criterion is tested whether the unit is
ON or OFF, and on units with three circuits only. If communication with Fan Board C is lost for a period of 10 seconds, the
alarm will be triggered.
Action to be Taken — If running, Circuit C will shut down normally. If the circuit is not running, then it will not be allowed to
start.
Reset Method — Automatic, if communication is established,
the unit will start normally.
Possible Causes — If this condition is encountered, check the
following items:
• power supply to Fan Board C
• address of the Fan Board C
• local equipment network (LEN) wiring
97
• The circuit’s Saturated Suction Temperature is less than
Maximum Operating Pressure (MOP) set point (EXV
MOP Setpoint, MOP) for more than 5 minutes.
Action to be Taken — The circuit is shut down normally.
Reset Method — Manual.
Possible Causes — If this condition is encountered, check the
following items:
• suction pressure transducer wiring to Main Base Board
(Alarm 59 and 60) or Fan Board C (Alarm 61)
• board for a faulty channel
• a faulty suction transducer
• suction gas thermistor wiring to EXV Board 1 (Alarm 41)
or to EXV Board 2 (Alarm 43)
• suction gas thermistor sensor for accuracy
• for EXV Board 1 (Alarm 41) or EXV Board 2 (Alarm 42)
faulty channel
• EXV operation
• a liquid line refrigerant restriction, filter drier, service valve,
etc.
• refrigerant charge
Low Suction Superheat
Alarm 62 — Circuit A (P.11)
Alarm 63 — Circuit B (P.12)
Alarm 64 — Circuit C (P.13)
Criteria for Trip — The criteria are tested when the circuit is
ON. This alarm is generated if the following criterion is met:
The EXV position is equal to or less than 5% and the circuit’s Suction Superheat (Suction Gas Temperature – Saturated
Suction Temperature) is less than the Suction Superheat Set
Point (EXVA Superheat Setpoint, SHP.A, EXVB Superheat
Setpoint, SHP.B, or EXVC Superheat Setpoint, SHP.C) by at
least 5° F (2.8° C) or the circuit Saturated Suction Temperature
is greater than Maximum Operating Pressure (MOP) set point
(EXV MOP Setpoint, MOP) for more than 5 minutes.
Action to be Taken — The circuit is shut down normally.
Reset Method — Automatic, first occurrence in 24 hours.
Manual, if more than one occurrence in 24 hours.
Possible Causes — If this condition is encountered, check the
following items:
• suction pressure transducer wiring to Main Base Board
(Alarm 62 and 63) or Fan Board C (Alarm 64)
• board for a faulty channel
• faulty suction transducer
• suction gas thermistor wiring to EXV Board 1 (Alarm 41)
or to EXV Board 2 (Alarm 42)
• suction gas thermistor sensor for accuracy
• EXV Board 1 (Alarm 41) or EXV Board 2 (Alarm 42)
faulty channel
• EXV operation
• confirm maximum operating pressure set point
• refrigerant charge level
Alarm 65 — Interlock Failure (P.14)
Criteria for Trip — The criteria are tested whether the unit is
ON or OFF. This alarm is generated if the lockout switch
(located in the Energy Management Module) is closed during
normal operation.
Action to be Taken — All compressors are shut down immediately without going through pumpdown. and is not allowed to
start.
Reset Method — Automatic, first occurrence in 24 hours.
Manual, if more than one occurrence in 24 hours.
Possible Causes — If this condition is encountered, check the
following items:
• chilled water flow switch operation
• water flow. Be sure all water isolation valves are open and
check water strainer for a restriction
• interlock wiring circuit
Possible Causes — If this condition is encountered, check the
following items:
• entering and leaving fluid thermistors for accuracy
• water flow rate
• loop volume — low loop volume at nominal flow rates can
in extreme cases bypass cold water to the cooler
• freezing conditions
• heater tape and other freeze protection items for proper
operation
• glycol concentration and adjust LOSP accordingly
• If the Leaving Water Set Point is above 40 F (4.4 C) and
there is glycol in the loop, consider using the Medium
Temperature Brine option (Cooler Fluid Type, FLUD=2)
to utilize the brine freeze point instead of 34 F (1.1 C)
Condenser Freeze Protection
Alarm 53 — Circuit A (P.02)
Alarm 54 — Circuit B (P.03)
Alarm 55 — Circuit C (P.04)
NOTE: Alarms 53-55 are not used or supported. If this condition is encountered, confirm machine configuration.
Low Saturated Suction Temperature
Alarm 56 — Circuit A (P.05)
Alarm 57 — Circuit B (P.06)
Alarm 58 — Circuit C (P.07)
Criteria for Trip — The criteria are tested only when the
circuit is ON. This alarm is generated if one of the following
criteria is met:
• If the circuit Saturated Suction Temperature is below –13 F
(–25 C) for more than 30 seconds or 40 seconds if OAT is
less than 14 F (–10 C) or LWT is less than 36 F (2.2 C).
• If the circuit Saturated Suction Temperature is below –22 F
(–30 C) for more than 10 seconds, or 20 seconds if OAT less
than 50 F (10 C).
Action to be Taken — The circuit is shut down immediately.
Prior to the alarm trip, the control will take action to avoid
the alarm. See Operating Modes 21, 22 and 23 on page 68.
Reset Method — Automatic, first occurrence in 24 hours.
Manual, if more than one occurrence in 24 hours.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to Main Base Board (Alarm 56 and 57) or Fan
Board C (Alarm 58)
• board for a faulty channel
• faulty suction transducer
• cooler water flow
• loop volume
• EXV operation
• liquid line refrigerant restriction, filter drier, service valve,
etc.
• refrigerant charge
• If the Leaving Water Set Point is above 40 F (4.4 C) and
there is glycol in the loop, consider using the Medium
Temperature Brine option (Cooler Fluid Type, FLUD=2)
to utilize the brine freeze point instead of 34 F (1.1 C).
• Closed suction service valve on DX Cooler units.
High Suction Superheat
Alarm 59 — Circuit A (P.08)
Alarm 60 — Circuit B (P.09)
Alarm 61 — Circuit C (P.10)
Criteria for Trip — The criteria are tested only when the circuit is ON. This alarm is generated if all of the following criteria are met:
• The EXV position is equal to or greater than 98%.
• The circuit’s Suction Superheat (Suction Gas Temperature –
Saturated Suction Temperature) is greater than the superheat control set point.
98
oil_sp2 = sp + 14.5 psi (45 seconds after start)
If the compressor starts with the ambient temperature (OAT
less than 36° F [2° C] the oil pressure monitoring is delayed by
30 seconds.
Action to be Taken — The affected compressor will be
stopped. The other compressors will continue to operate.
Reset Method — Manual.
Possible Causes — If this condition is encountered, check the
following items:
• sensor wiring to the CPM Board
• board for a faulty channel
• faulty transducer
• plugged oil filter
• faulty oil solenoid valve coil
• stuck oil solenoid valve
• stuck check valve
• manual shut off valve to ensure it is fully open
• confirm unit configuration
Max Oil Filter Differential Pressure Failure
Alarm 72 — Circuit A (P.70)
Alarm 73 — Circuit B (P.71)
Alarm 74 — Circuit C (P.72)
Criteria for Trip — The criterion is tested when the compressor has been operating for at least 5 seconds. The alarm is
generated if the difference between the Circuit Discharge Pressure and the Compressor Oil Pressure is greater than 50 psi
(345 kPa) for more than 30 seconds.
Action to be Taken — The affected compressor will be turned
off.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• check the discharge and oil sensor wiring to the Main Base
Board and CPM board
• boards for a faulty channel
• faulty transducer
• plugged oil filter
• faulty oil solenoid valve coil
• stuck oil solenoid valve
• stuck check valve
• manual shut off valve to ensure it is fully open
Check the power supply to the System Manager and unit
controls.
High Oil Filter Pressure Drop
Alarm 75 — Circuit A (P.84)
Alarm 76 — Circuit B (P.85)
Alarm 77 — Circuit C (P.86)
Criteria for Trip — The criterion is tested when the compressor has been operating for at least 5 seconds. The alarm is generated if the difference between the Circuit Discharge Pressure
and the Compressor Oil Pressure is greater than 30 psi for
more than 5 minutes.
Action to be Taken — The compressor will continue to run.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• discharge and oil sensor wiring to the Main Base Board and
CPM board
• boards for a faulty channel
• faulty transducer
• plugged oil filter
• faulty oil solenoid valve coil
• oil solenoid valve stuck open
• stuck check valve
• manual shut off valve to ensure it is fully open
• power supply to the pump
• control signal to the pump controller
• chilled water pump operation
• cooler pump contactor for proper operation
Alarm 66 — Electrical Box Thermostat Failure/Reverse
Rotation (P.28)
Criteria for Trip — The alarm criteria are checked whether the
unit is ON or OFF. If channel 15A on the MBB, which is used
for field wired external pump interlock, is open then the alarm
will be generated.
Action to be Taken — Unit shut down or note allowed to start.
Reset Method — Automatic, if the channel is closed, the unit
will start normally.
Possible Causes — If this condition is encountered, check the
following items:
• jumper wiring on TB5-1 and TB5-2 when channel is not in
use
• external pump status
• field wiring for the external pump interlock
Alarm 67 — Loss of Communication with System Manager
(P.29)
Criteria for Trip — The criterion is tested whether the unit is
ON or OFF. This alarm is generated if the System Manager
had established communications with the machine and is then
lost for more than 2 minutes.
Action to be Taken — The action to be taken by the control
depends on the configuration. If Auto Start when SM lost is
enabled, (Cooler Heater Delta Spt, AU.SM=YES), then the
unit will force the CCN Chiller Start Stop to ENBL and clear
all forced points from the System Manager. The unit will revert
to stand-alone operation.
Reset Method — Automatic, once communication is
re-established.
Possible Causes — If this condition is encountered, check the
following items:
• communication wiring
• power supply to the System Manager and unit controls
Alarm 68 — Master/Slave Communication Failure (P.30)
Criteria for Trip — The criterion is tested whether the units are
ON or OFF and a master and slave machine has been configured, (Master/Slave Select, MSSL=1 and Master/Slave
Select, MSSL=2). If communication is lost for more than 3
minutes, this alarm is generated.
Action to be Taken — Dual chiller control will be disabled and
each unit will operate in Stand-Alone mode.
Reset Method — Automatic, once communication is
re-established.
Possible Causes — If this condition is encountered, check the
following items:
• CCN wiring
• control power to each Main Base Board, master and slave
• confirm correct configuration
Low Oil Pressure
Alarm 69 — Circuit A (P.67)
Alarm 70 — Circuit B (P.68)
Alarm 71 — Circuit C (P.69)
Criteria for Trip — The criteria are tested only when the compressor is ON. The alarm is generated if one of the following
occurs, where:
oil = oil pressure transducer reading for the appropriate compressor
sp = suction pressure reading for the affected circuit
dp = discharge pressure reading for the affected circuit
oil_sp1 = 0.7 x (dp-sp) + sp
oil_sp2 = sp + 7.2 psi (15 seconds after start)
99
Check the power supply to the System Manager and unit
controls.
Low Oil Level Failure
Alarm 78 — Circuit A (P.75)
Alarm 79 — Circuit B (P.76)
Alarm 80 — Circuit C (P.77)
Criteria for Trip — The criteria are tested whether the compressor is on or off. The alarm is generated if:
• The compressor is not running and an increase in capacity is
required and the compressor is not started.
• The compressor is running and the oil level switch is open
for more than 45 seconds.
Action to be Taken — The affected compressor will be turned
off.
Reset Method — Automatic, when the oil level is elevated,
first three times the alarm is tripped in a 24-hour period. Manual if alarm is tripped more than three times in a 24-hour
period.
Possible Causes — If this condition is encountered, check the
following items:
• oil level in the oil separator
• oil level switch wiring to the CPM board
• CPM board for a faulty channel
• faulty oil level switch
• oil solenoid valve stuck open
Alarm 81 — Master Chiller Configuration Error (MC.nn)
Criteria for Trip — The criterion is tested whether the unit is
ON or OFF. The units must be configured as a Master and
Slave machine (Master/Slave Select, MSSL=1 and Master/
Slave Select, MSSL=2), and one of the following configuration errors has been found. The “nn” refers to the error code
listed in Table 60.
Action to be Taken — Unit not allowed to start in Master Slave
control.
Reset Method — Automatic
Possible Causes — If this condition is encountered, check the
following:
• CCN wiring.
• Control power to each Main Base Board, master and slave.
• Move to first position.
• Confirm unit configuration.
Alarm 82 — Initial Factory Configuration Required (FC.n0)
Criteria for Trip — The criterion is tested whether the unit is
ON or OFF. The alarm will be generated if the Unit Capacity
Model, TONS=0.
Action to be Taken — The unit is not allowed to start.
Reset Method — Automatic after factory configuration is complete. The configuration must be manually completed.
Possible Causes — If this condition is encountered, confirm
the unit configuration.
Alarm 83 — Illegal Configuration (FC.nn)
Criteria for Trip — The criterion is tested whether the unit is
ON or OFF. The alarm will be generated if the one of the
following configuration errors is detected by the control. The
“nn” refers to the error code listed in Table 61.
Action to be Taken — The unit is not allowed to start.
Reset Method — Automatic after reconfiguration is completed.
Possible Causes — If this condition is encountered, confirm
the unit configuration (None, UNIT).
Alarm 84 — Unit is in Emergency Stop (P.31)
Criteria for Trip — The criterion is tested whether the units are
ON or OFF and when the machine receives a Carrier Comfort
Network® (CCN) command for an Emergency Stop.
Action to be Taken — Unit will stop, or will not allowed to
start.
Reset Method — Automatic, once a return to normal command
is received.
Possible Causes — If this condition is encountered, check for
CCN Emergency Stop command.
Cooler Pump Fault
Alarm 85 — Pump 1 Fault (P.32)
Alarm 86 — Pump 2 Fault (P.33)
Criteria for Trip — The criterion is tested whether the units are
ON or OFF. This alarm will be generated if the cooler pump
interlock opens. When starting the pump, the control must
read an open circuit for 3 consecutive reads. If the pump is
operating and the circuit opens, the alarm will be generated
immediately.
Action to be Taken — The pump and machine will be shut
down. If there is another pump available, the control will start
that pump, restart the machine and clear the alarm. If no other
pump is available, the unit will remain OFF.
Reset Method — Manual.
Possible Causes — If this condition is encountered, check the
following items:
• interlock wiring circuit
• control signal to the pump controller
• cooler pump contactor for proper operation
• control voltage for proper voltage (on 208-volt systems, be
sure the proper tap on TRAN1 is utilized)
Alarm 87 — Condenser Flow Switch Failure (P.15)
NOTE: Alarm 87 is not used or supported. If this condition is
encountered, confirm machine configuration.
Reclaim Operation Failure
Alarm 88 — Circuit A (P.34)
Alarm 89 — Circuit B (P.35)
Repeated High Discharge Gas Overrides
Alarm 90 — Circuit A (P.37)
Alarm 91 — Circuit B (P.38)
Alarm 92 — Circuit C (P.39)
Criteria for Trip — The criterion is tested when the circuit is
ON. This alarm will be tripped if the circuit capacity is reduced
more than 8 times in 30 minutes due to high discharge gas temperatures. If no override occurs in a 30-minute period, the
counter is reset.
Action to be Taken — The affected circuit will be shut down.
Reset Method — Automatic, after 30 minutes. If the alarm is
cleared via the Manual method, the counter will be reset to
zero.
Possible Causes — If this condition is encountered, check the
following items:
• Maximum Condensing Temperature (MCT) for the proper
setting
• noncondensables in the refrigerant circuit
• condenser air re-circulation
• proper refrigerant charge (overcharged)
• operation beyond the limit of the machine
• condenser coils for debris or restriction
• condenser fans and motors for proper rotation and operation
• discharge service valve to be sure that it is open. Check the
discharge pressure transducer for accuracy
• confirm unit configuration
100
Table 60 — Master/Slave Alarm Code
MC
ERROR
CODE
MASTER
SLAVE
DESCRIPTION
01
X
X
02
03
04
X
X
X
05
X
06
X
07
X
08
X
09
10
11
12
13
X
X
X
X
X
The master or slave water pump is not configured while the control of the lag unit pump is required
(lag_pump = 1)
Master and slave units have the same network address.
There is no slave configured at the slave address
Slave pump_seq incorrect configuration
There is a conflict between the master and the slave LWT option: the master is configured for EWT control
while the slave is configured for LWT control.
There is a conflict between the master and the slave LWT option: the master is configured for LWT control
while the slave is configured for EWT control.
There is a conflict between the master and the slave pump option: the master is configured for lag pump
control while the slave is not configured for lag pump control.
There is a conflict between the master and the slave pump option: the master is not configured for lag pump
control while the slave is configured for lag pump control.
The slave chiller is in local or remote control (chilstat = 3)
The slave chiller is down due to fault (chilstat = 5)
The master chiller operating type is not Master: master_oper_typ
No communication with slave.
Master and slave heat cool status are not the same.
X
X
X
LEGEND
EWT — Entering Water Temperature
LWT — Leaving Water Temperature
NOTE: Alarms 97 and 98 are not used or supported. If this
condition is encountered, confirm machine configuration.
High Discharge Temperature
Alarm 99 — Circuit A (P.78)
Alarm 100 — Circuit B (P.79)
Alarm 101 — Circuit C (P.80)
Criteria for Trip — The criterion is tested when the compressor is operating. This alarm will be tripped if the discharge gas
temperature is higher than 212 F (100 C) for more than
90 seconds.
Action to be Taken — The affected compressor will be
stopped.
Reset Method — Manual.
Possible Causes — If this condition is encountered, check the
following items:
• noncondensables in the refrigerant circuit
• condenser air re-circulation
• proper refrigerant charge (undercharged) EXV operation
• EXV operation
• operation beyond the limit of the machine
• condenser coils for debris or restriction
• condenser fans and motors for proper rotation and operation
• the discharge service valve to be sure that it is open, check
the discharge pressure transducer for accuracy
• confirm unit configuration
Low Economizer Pressure
Alarm 102 — Circuit A (P.81)
Alarm 103 — Circuit B (P.82)
Alarm 104 — Circuit C (P.83)
Criteria for Trip — The criterion is tested when the compressor is operating to prevent pumpdown conditions when the
suction service valve is closed. This alarm will be tripped if the
economizer pressure is below the suction pressure more than
1 bar (14.5 psi) for more than 10 seconds.
Action to be Taken — The affected compressor will be
stopped.
Reset Method — Manual.
Possible Causes — If this condition is encountered, check the
following items:
• suction service valve is closed
• sensor wiring to the EXV boards
Table 61 — Illegal Configuration Alarm Code
FC
ERROR
CODE
01
02
03
04
DESCRIPTION
Unit size is unknown.
Reclaim option selected for Heat Pump machine.
Hot Gas Bypass configured for a Heat Pump machine.
Number of Fans controlled by low ambient temperature
head pressure control is greater than expected.
Repeated Low Suction Temperature Protection
Alarm 93 — Circuit A (P.40)
Alarm 94 — Circuit B (P.41)
Alarm 95 — Circuit C (P.42)
Criteria for Trip — The criterion is tested when the circuit is
ON. If the circuit operates and if more than 8 successive circuit
capacity decreases (stop the compressor) have occurred because
of low suction temperature protection overrides, the circuit
alarm will be tripped. If no override has occurred for more than
30 minutes, the override counter will be reset to zero.
Action to be Taken — ALARM_LED will be set to blinking.
Alert relay will be energized.
Reset Method — Automatic, when the override counter returns
to zero. If the alarm is cleared via the Manual method, the
counter will be forced to zero.
Possible Causes — If this condition is encountered, check the
following items:
• suction transducer for accuracy
• suction transducer wiring
• EXV operation
• proper refrigerant charge (undercharged)
• evaporator loop for low water flow
• evaporator leaving water temperature
• suction service valve to be sure it is open
• plugged filter drier
Alarm 96 — Low Entering Water Temperature in Heating
(P.43)
NOTE: Alarm 96 is not used or supported. If this condition is
encountered, confirm machine configuration.
Condenser Default
Alarm 97 — Pump 1 (P.73)
Alarm 98 — Pump 2 (P.74)
101
Action to be Taken — The chiller is shut down immediately.
Reset Method — Manual.
Possible Causes — If this condition is encountered, check the
following items:
• Check LWT and EWT wiring at main base board (connector J6, channels 1,2).
• Check for a faulty entering or leaving water temperature
sensor.
• Check cooler nozzles for proper water temperature sensor
locations.
Alarm 110 — Service Maintenance Alert (Sr.nn)
Criteria for Trip — This alert is tested whether the unit is ON
or OFF and when the Servicing Alert decisions listed under
Time ClockMCFG have been enabled. The alarm will be
generated if the one of the following configuration errors is
detected by the control. The “nn” refers to the error code listed
in Table 62.
• boards for faulty channels
• faulty transducer
• economizer EXV operation
Slide Valve Control Unverifiable
Alarm 105 — Circuit A (P.87)
Alarm 106 — Circuit B (P.88)
Alarm 107 — Circuit C (P.89)
Criteria for Trip — The criteria are tested when the compressor is operating and the active cooling set point is greater than
32° F (0° C). This alarm will be tripped if the circuit is operating at 100% of capacity and the measured current is less than
1.1 times the current at fully unloaded 30% for more than one
minute.
Action to be Taken — The affected compressor will continue to
run.
Reset Method — Manual.
Possible Causes — If this condition is encountered, check the
following items:
• faulty unloader solenoid valves
• faulty unloader solenoid coils
• wiring of the unloader solenoid valves
• CPM board for faulty channels
• current transformer reading for accuracy
Alarm 108 — Cooler Flow Switch Setpoint Configuration
Failure (P.90)
NOTE: Alarm 108 is not used or supported. If this condition is
encountered, confirm machine configuration.
Alarm 109 — Cooler Flow Switch Failure (P.91)
Criteria for Trip — The criteria are tested when the unit is on
or off. This alarm will be tripped when the unit is on if:
• The flow switch fails to close after the Off/On delay.
• If the master/slave control is active, the unit is the lag chiller
and if the cooler flow switch fails to close within one minute
after the cooler pump was restarted. The alarm is ignored if
the lag cooler pump is stopped as a result of master/slave
control.
• The flow switch is opened during normal operation.
The alarm will be tripped when the unit is off if:
• The cooler pump control is enabled (Cooler Pumps
Sequence, PUMP=0)and the cooler flow switch is checked
when the pump is enabled (Flow Checked if C Pump Off,
P.LOC) and the cooler flow switch is closed after the cooler
pump is commended OFF for more than 2 minutes.
• The flow switch fails to close after the Off/On delay after
the cooler pump has been turned on to protect the cooler
from freezing (Cooler Pumps Sequence, PUMP=0).
Action to be Taken — For criteria for trip A1 and A2, the compressors will not be started.
For criteria for trip A3, all compressors will be stopped without
going through pumpdown. Cooler pump will be stopped with
no delay.
For criteria for trip B1, the unit will not start.
Reset Method — Manual if at least one compressor is operating. Automatic if no compressors are operating.
Possible Causes — If this condition is encountered, check the
following items:
• a faulty flow switch
• flow switch wiring
• Main Base Board for a faulty channel
• Minutes off time set to 0 (DELY, unit off to on delay)
Alarm 127 — Water Exchanger Temperature Sensors
Swapped (P.97)
Criteria for Trip — The alarm criterion is checked when the
chiller is ON and one or more compressors is running. This
alarm will be tripped if the entering water temperature is less
than the leaving water temperature for more than 1 minute.
Table 62 — Service Maintenance Alert Codes
CODE
Sr.01
Sr.02
Sr.03
Sr.04
Sr.05
Sr.06
Sr.07
Sr.08
Sr.09
Sr.10
Sr.11
Sr.12
Sr.13
DESCRIPTION
Circuit A Loss of Refrigerant Charge
Circuit B Loss of Refrigerant Charge
Circuit C Loss of Refrigerant Charge
Water Loop Size Warning
Air Exchanger Cleanliness Warning
Cooler Pump 1 Servicing Required
Cooler Pump 2 Servicing Required
Condenser Pump 1 Servicing Required
Condenser Pump 2 Servicing Required
Water Filter Servicing Required
Compressor A Oil Filter Servicing Required
Compressor B Oil Filter Servicing Required
Compressor C Oil Filter Servicing Required
Action to be Taken — None.
Reset Method — Manual, after the service has been completed.
Possible Causes — If the Sr-01, 02, or 03 conditions are
encountered, check the following items:
• refrigerant charge
• sensor wiring to the Main Base Board
• sensor for accuracy
Compressor Motor Temperature Too High
Alarm 111-01 — Circuit A (A1.01)
Alarm 112-01 — Circuit B (B1.01)
Alarm 113-01 — Circuit C (C1.01)
Criteria for Trip — The alarm criteria are checked when the
compressor is ON. This alarm will be generated if:
• The temperature is greater than 245 F (118 C) and it has
been greater than 212 F (100 C) for 10 consecutive seconds.
• The compressor temperature is greater than 232 F (111 C)
for 90 seconds (but less than 250 F [120 C]).
Action to be Taken — The circuit shuts down immediately.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• faulty wiring and loose plugs
• faulty CPM board
Compressor Motor Temperature Out of Range
Alarm 111-02 — Circuit A (A1.02)
Alarm 112-02 — Circuit B (B1.02)
Alarm 113-02 — Circuit C (C1.02)
Criteria for Trip — The alarm criterion is checked when the
compressor is ON. This alarm will be generated if: the temperature is greater than 245 F (118 C) and it has NOT been greater
than 212 F (100 C) for 10 consecutive seconds.
102
Criteria for Trip — The alarm criteria are checked during
startup when the compressor is ON. This alarm will be generated if:
• The current unbalance on any of the 3 phases is greater than
48% for more than 1 second continuously during start-up.
• The current unbalance on any of the 3 phases is greater than
48% for more than 2 seconds continuously during runtime.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• power failure
• blown fuse or tripped circuit breaker
• power wiring errors or loose terminals
Compressor Low Current
Alarm 111-09 — Circuit A (A1.09)
Alarm 112-09 — Circuit B (B1.09)
Alarm 113-09 — Circuit C (C1.09)
Criteria for Trip — The alarm criteria are checked when the
compressor is ON. This alarm will be generated if:
• The current is less than 15% MTA on all three legs for more
than 1 second for Wye-Delta start units.
• If the current is less than 15% of MTA on all three legs for
more than 1 second for direct start units.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• power failure
• blown fuse or tripped circuit breaker
• deenergized contactor
• faulty current toroid
• high pressure switch (HPS) trip (when auto reset HPS is
used)
Compressor Wye-Delta Starter Current Increase Failure
Alarm 111-10 — Circuit A (A1.10)
Alarm 112-10 — Circuit B (B1.10)
Alarm 113-10 — Circuit C (C1.10)
Criteria for Trip — The alarm criterion is checked during
compressor start-up. This alarm will be generated if the current
in Delta mode is not more than 25% greater than the current in
Y mode within 550 ms.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• power supply failure to the delta contactor
• faulty wiring to the delta contactor
• faulty CPM board
• faulty current toroid
Compressor Contactor Failure
Alarm 111-11 — Circuit A (A1.11)
Alarm 112-11 — Circuit B (B1.11)
Alarm 113-11 — Circuit C (C1.11)
Criteria for Trip — The alarm criterion is checked during
compressor shutdown. This alarm will be generated if the current is greater than 15% of the MTA on at least one phase for
10 continuous seconds.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• faulty or welded contactor
• faulty wiring
• faulty CPM board
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• faulty compressor temperature thermistor
• faulty wiring and loose plugs
• faulty CPM board
Compressor High Pressure Switch Protection
Alarm 111-03 — Circuit A (A1.03)
Alarm 112-03 — Circuit B (B1.03)
Alarm 113-03 — Circuit C (C1.03)
Criteria for Trip — The alarm criterion is checked when the
compressor is ON. This alarm will be generated if the circuit
high-pressure switch (HPS) opens for more than 2 seconds.
The CPM board monitors the HPS switch.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual (reset button on switch)
Possible Causes — If this condition is encountered, check the
following items:
• condenser fan or contactor failure of loss of condenser air
flow
• compressor operating beyond the operation envelope
• faulty high pressure switch or wiring
• faulty CPM board
Compressor Overcurrent
Alarm 111-04 — Circuit A (A1.04)
Alarm 112-04 — Circuit B (B1.04)
Alarm 113-04 — Circuit C (C1.04)
Criteria for Trip — The alarm criterion is checked when the
compressor is ON. This alarm will be generated if the CPM
board detects a motor current greater than 93% MTA (must
trip amps) and less than 2 times that for more than 1.7 seconds.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• Compressor operating beyond the operation envelope.
• Incorrect MTA setting.
Compressor Locked Rotor
Alarm 111-05 — Circuit A (A1.05)
Alarm 112-05 — Circuit B (B1.05)
Alarm 113-05 — Circuit C (C1.05)
Criteria for Trip — The alarm criterion is checked during
start-up when the compressor is ON. This alarm will be generated if the CPM board detects a high motor current compared
with the MTA (must trip amps) setting for more than 450 ms.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• compressor mechanical failure
• unloader slide valve failure
• compressor motor failure
Compressor Phase Loss
Alarm 111-06 — Circuit A L1 (A1.06)
Alarm 112-06 — Circuit B L1 (B1.06)
Alarm 113-06 — Circuit C L1 (C1.06)
Alarm 111-07 — Circuit A L2 (A1.07)
Alarm 112-07 — Circuit B L2 (B1.07)
Alarm 113-07 — Circuit C L2 (C1.07)
Alarm 111-08 — Circuit A L3 (A1.08)
Alarm 112-08 — Circuit B L3 (B1.08)
Alarm 113-08 — Circuit C L3 (C1.08)
103
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• incorrect CPM board settings
• faulty CPM board
Compressor Power on Reset
Alarm 111-17 — Circuit A (A1.17)
Alarm 112-17 — Circuit B (B1.17)
Alarm 113-17 — Circuit C (C1.17)
Criteria for Trip — The alarm criterion is checked when the
compressor is ON. This alarm will be generated if the CPM
board detects a power failure.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check for
power interruptions.
Compressor UL 1998 Critical Section Software Error
Alarm 111-18 — Circuit A (A1.18)
Alarm 112-18 — Circuit B (B1.18)
Alarm 113-18 — Circuit C (C1.18)
Criteria for Trip — The alarm criterion is checked when the
compressor is ON. This alarm will be generated if the CPM
board detects a software error.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• electrical noise
• faulty CPM board
Compressor UL 1998 Current Measure Dual Channel Mismatch
Alarm 111-19 — Circuit A (A1.19)
Alarm 112-19 — Circuit B (B1.19)
Alarm 113-19 — Circuit C (C1.19)
Criteria for Trip — The alarm criterion is checked when the
compressor is ON. This alarm will be generated if the CPM
board detects a software error.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• electrical noise
• faulty CPM board
Compressor Unable to Stop Motor
Alarm 111-12 — Circuit A (A1.12)
Alarm 112-12 — Circuit B (B1.12)
Alarm 113-12 — Circuit C (C1.12)
Criteria for Trip — The alarm criterion is checked during
compressor shutdown. This alarm will be generated if after
three attempts to turn off the compressor outputs and the current is still greater than 15% of the MTA on at least one phase
for 10 continuous seconds.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• faulty or welded contactor
• faulty wiring
Compressor Phase Reversal
Alarm 111-13 — Circuit A (A1.13)
Alarm 112-13 — Circuit B (B1.13)
Alarm 113-13 — Circuit C (C1.13)
Criteria for Trip — The alarm criterion is checked during
compressor start-up. This alarm will be generated if the CPM
board detects a phase reversal from the current toroid.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• if power supply lead at the terminal block is not operating at
the correct phase
• if power supply is crossed when going through the current
toroid
Compressor MTA Configuration Fault
Alarm 111-14 — Circuit A (A1.14)
Alarm 112-14 — Circuit B (B1.14)
Alarm 113-14 — Circuit C (C1.14)
Criteria for Trip — The alarm criterion is checked whether the
compressor is ON or OFF. This alarm will be generated if the
MTA setting is out of the allowed MTA range.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• incorrect MTA settings
• faulty CPM board
Compressor Configuration Switch Mismatch
Alarm 111-15 — Circuit A (A1.15)
Alarm 112-15 — Circuit B (B1.15)
Alarm 113-15 — Circuit C (C1.15)
Criteria for Trip — The alarm criterion is checked whether the
compressor is ON or OFF. This alarm will be generated if
the CPM board S1 and S2 setting does not match software
configuration.
Action to be Taken — The compressor will be stopped.
Reset Method — Manual
Possible Causes — If this condition is encountered, check the
following items:
• incorrect CPM board settings
• faulty CPM board
Compressor Unexpected Switch Setting Change
Alarm 111-16 — Circuit A (A1.16)
Alarm 112-16 — Circuit B (B1.16)
Alarm 113-16 — Circuit C (C1.16)
Criteria for Trip — The alarm criterion is checked when the
compressor is ON. This alarm will be generated if the CPM
board S1 setting has changed.
Service Test — Main power and control circuit power
must be on for Service Test.
The Service Test function is used to verify proper operation
of various devices within the chiller, such as condenser fan(s),
compressors, minimum load valve solenoid (if installed),
cooler pump(s) and remote alarm relay. This is helpful during
the start-up procedure to determine if devices are installed
correctly. See Fig. 63-65 for 30XA wiring diagrams.
To use the Service Test mode, the Enable/Off/Remote Contact switch must be in the OFF position. Use the display keys to
move to the Service Test mode. The items are described in the
Service Test table. There are two sub-modes available. Service
Test Enable, T.REQ allows for manual control of the
compressors and minimum load control. In this mode the compressors will operate only on command. The capacity control
and head pressure control algorithms will be active. The condenser fans will operate along with the EXVs. There must be a
load on the chiller to operate for an extended period of time.
All circuit safeties will be honored during the test. Quick Test
Enable, Q.REQ allows for test of EXVs, condenser fans,
pumps, low ambient head pressure control speed control, oil
104
access Q.REQ. Press ENTER and the display will show OFF.
Press ENTER and OFF will flash. Enter the password if
required. Use either arrow key to change the QUIC value to
ON and press ENTER . Quick Test mode is now active. Follow the same instructions for the Manual Control mode to activate a component (see Table 63).
separator, cooler heaters, oil solenoids, unloader solenoids and
status points (alarm relays, running status and chiller capacity).
If there are no keys pressed for 5 minutes, the active test mode
will be disabled.
To enter the Manual Control mode with the Navigator™
display, the Enable/Off/Remote Contact switch must be in the
OFF position. Move the LED to the Service Test mode. Press
ENTER to access TEST. Press ENTER to access T.REQ.
Press ENTER and the display will show OFF. Press
ENTER and OFF will flash. Enter the password if required.
Use either arrow key to change the T.REQ value to ON and
press ENTER . Place the Enable/Off/Remote Switch in the
enable position. Manual Control mode is now active. Press the
arrow keys to move to the appropriate item. To activate an item
locate the item, press ENTER and the display will show OFF.
Press ENTER and OFF will flash. Use either arrow key to
change the value to ON and press ENTER . The item should
be active. To turn the item off, locate the item, press ENTER
and the display will show ON. The chiller must be enabled by
turning the Enable/Off/Remote Contact switch to Enable. Press
ENTER and ON will flash. Use either arrow key to change
the value to OFF and press ENTER . The item should be
inactive.
Example — Test the condenser fan A1.
Power must be applied to the unit. Enable/Off/Remote
Contact switch must be in the OFF position.
Test the condenser fans, cooler pump(s) and alarm relay by
changing the item values from OFF to ON. These discrete
outputs are then turned off if there is no keypad activity for
10 minutes. Test the compressor and minimum load valve solenoid (if installed) outputs in a similar manner. The minimum
load valve solenoids will be turned off if there is no keypad
activity for 10 minutes. Compressors will stay on until the operator turns them off. The Service Test mode will remain enabled for as long as there is one or more compressors running.
All safeties are monitored during this test and will turn a compressor, circuit or the machine off if required. Any other mode
or sub-mode can be accessed, viewed, or changed during the
Manual Control mode only. The STAT item (Run StatusVIEW) will display “0” as long as the Service mode is
enabled. The TEST sub-mode value must be changed back to
OFF before the chiller can be switched to Enable or Remote
contact for normal operation.
NOTE: There may be up to a one-minute delay before the
selected item is energized.
To enter the Quick Test mode, the Enable/Off/Remote
Contact switch must be in the OFF position. Move the LED to
the Service Test mode. Press ENTER to access TEST. Use
the
key until the display reads QUIC. Press ENTER to
105
Table 63 — Testing Circuit A Oil Solenoid
MODE
(Red LED)
SUB-MODE
SERVICE TEST
KEYPAD
ENTRY
ITEM
VALUE
DESCRIPTION
(Units)
COMMENT
Service Test Mode
ENTER
TEST
QUIC
DISPLAY
EXPANSION
Manual Sequence
ENTER
Q.REQ
PASS WORD
Password may be required
0111
ENTER
ENTER
Each
ENTER
digit. If 0111 is not the password,
ENTER
will lock in the next
use the arrow keys to change the
ENTER
password digit and press
ENTER
Q.REQ
Returns to the original field
ENTER
OFF
ENTER
OFF
OFF will flash
ON
The Enable/Off/Remote Contact
switch must be in the OFF
position.
ESCAPE
Q.REQ
EXV.A
Press 15 times.
OLS.A
Oil Solenoid Cap.A
ENTER
OFF
ENTER
OFF
OFF will flash
ON
ENTER
ON
OLS.A will turn on.
ENTER
ON
1 will flash
OFF
OFF
ENTER
OLS.A will turn off.
LEGEND FOR FIG. 63-65
ALM
ALT
CB
CLR
CPM
CWFS
DPT
ECEXV
ECTA
EMM
EXV
FC
FIOP
—
—
—
—
—
—
—
—
—
—
—
—
—
ENTER
when correct.
ENTER
Alarm
Alert
Circuit Breaker
Clear
Compressor Protection Module
Chilled Water Flow Switch
Discharge Pressure and Temperature
Economizer Electronic Expansion Valve
Economizer A Temp
Energy Management Module
Electronic Expansion Valve
Fuse
Factory-Installed Option
HGBP
LWT
MBB
MLV
MM
OAT
PMP
SGT
SHD
SPT
TB
UPC
106
—
—
—
—
—
—
—
—
—
—
—
—
Hot Gas Bypass
Leaving Water Temperature
Main Base Board
Minimum Load Valve
Low Ambient Temperature Head Pressure Control
Outdoor Air Temperature
Pump
Saturated Gas Temperature
Loadshed
Space Temperature
Terminal Block
Universal Protocol Converter/BacNet
Communications Option
a30-5255
Fig. 63 — 30XA080,082 Low Voltage Control Schematic
107
a30-5256
Fig. 64 — 30XA090-352 Low Voltage Control Schematic
108
a30-5257
Fig. 65 — 30XA400-500 Low Voltage Control Schematic
109
APPENDIX A — TOUCH PILOT DISPLAY TABLES
The Touch Pilot™ display tables are formatted in alphabetical order based on the point
name description. The line number corresponds to the line number from the top the Touch
Pilot screen. A cross reference to the CCN tables in Appendix C is provided. Please refer
to Appendix C for range and configuration default information.
TOUCH PILOT DESCRIPTION
110
1 Elec Stage for backup
3 Way Valve Position
3 Way Valve Position
Circuit A
Circuit B
Circuit C
3 Way Valve Status
Circuit A
Circuit B
Circuit C
4 way Valve Circuit A
4 way Valve Circuit B
4 Way Refrigerant Valve
Circuit A
Circuit B
Circuit C
Activate
Active Capacity Override
Active Demand Limit Val
Actual Capacity
Actual Capacity Limit
Actual Chiller Current
Actual Chiller Current
Air Cond Enter Valve A
Air Cond Enter Valve B
Air Cond Entering Valv A
Air Cond Entering Valv B
Air Cond Leaving Valv A
Air Cond Leaving Valv B
Air Cond Leaving Valve A
Air Cond Leaving Valve B
Air Cooled Reclaim Sel
Alarm Equipment Priority
Alarm Relay Output
Alarm Relay Status
Alarm Routing Control
Alarm State
Alarm System Name
Alert Relay Output
Alert Relay Status
Auto Changeover Active
Auto Changeover Select
Auto Start When SM Lost
AUX Board #1 Part Number
AUX Board #2 Part Number
AUX Board #3 Part Number
AUX Board #4 Part Number
AUX Board #5 Part Number
Average Ctrl Water Temp
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
ehs_back
Q_3W_VLV
NOTE: In places where duplicated point name descriptions were used, the headers were
added to the point name description to differentiate them. For example, the description 3
Way Valve Position is used three times for circuits A, B, and C. In this table, the descriptions include Circuit A, Circuit B, and Circuit C.
MAIN MENU\Config\USER
MAIN MENU\Status\QCK_TST2
35
11
READ/
WRITE
RW
RW
fc_vlv_a
fc_vlv_b
fc_vlv_c
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
14
24
34
RO
RO
RO
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
FC_VLV_A
FC_VLV_B
FC_VLV_C
Q_RV_A
Q_RV_B
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\QCK_TST2
15
25
35
13
14
RO
RO
RO
RW
RW
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\QCK_TST2
Status Display Tables\QCK_TST2
RV_A
RV_B
RV_C
ccnbroad
over_cap
DEM_LIM
cap_t
cap_lim
TOT_CURR
TOT_CURR
Q_HREA_A
Q_HREA_B
hr_ea_a
hr_ea_b
Q_HRLA_A
Q_HRLA_B
hr_la_a
hr_la_b
recl_opt
EQP_TYP
Q_ALARM
ALARMOUT
ALRM_CNT
ALM
ALRM_NAM
Q_ALERT
ALERT
Mode_12
auto_sel
auto_sm
AUX_BRD1
AUX_BRD2
AUX_BRD3
AUX_BRD4
AUX_BRD5
ctrl_avg
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
MAIN MENU\Config\BRODEFS
MAIN MENU\Maint\LOADFACT
MAIN MENU\Status\GENUNIT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Service\FACTORY
MAIN MENU\Config\ALARMDEF
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\STATEGEN
MAIN MENU\Config\ALARMDEF
MAIN MENU\Status\GENUNIT
MAIN MENU\Config\ALARMDEF
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\MODES
MAIN MENU\Config\USER
MAIN MENU\Service\SERVICE1
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\LOADFACT
24
24
23
1
20
21
8
9
10
23
3
7
15
25
4
8
17
27
10
2
48
28
1
13
5
49
29
13
18
18
4
5
6
7
8
2
RO
RO
RO
RW
RO
RO
RO
RO
RO
RO
RW
RW
RO
RO
RW
RW
RO
RO
RW
RW
RW
RO
RW
RO
RW
RW
RO
RO
RW
RW
RO
RO
RO
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
Configuration Tables\BRODEFS\BROCASTS
Maintenance Display Tables\LOADFACT
Status Display Tables\GENUNIT
Maintenance Display Tables\LOADFACT
Maintenance Display Tables\LOADFACT
Maintenance Display Tables\LOADFACT
Status Display Tables\GENUNIT
Status Display Tables\QCK_TST2
Status Display Tables\QCK_TST2
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\QCK_TST2
Status Display Tables\QCK_TST2
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Service Configuration Tables\FACTORY
Configuration Tables\ALARMDEF\ALARMS01
Status Display Tables\QCK_TST1
Status Display Tables\STATEGEN
Configuration Tables\ALARMDEF\ALARMS01
Status Display Tables\GENUNIT
Configuration Tables\ALARMDEF\ALARMS01
Status Display Tables\QCK_TST1
Status Display Tables\STATEGEN
Status Display Tables\MODES
Configuration Tables\USER
Service Configuration Tables\SERVICE1
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\LOADFACT
TOUCH PILOT PATH
LINE
CCN TABLE NAME
Configuration Tables\USER
Status Display Tables\QCK_TST2
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
111
Ball Valve Closing Out
Circuit A
Circuit B
Circuit C
Ball Valve Opening Out
Circuit A
Circuit B
Circuit C
Ball Valve Position
Circuit A
Circuit B
Circuit C
Baud rate
Brine flow Switch SP
Brine Freeze Setpoint
Broadcast acknowledger
Bus
CCN Chiller Start/Stop
Chiller Capacity in0-10v
Chiller Capacity Signal
Chiller Current Limit
Chiller Current Limit
Chiller in Series
Chiller Occupied?
Chiller Ready Output
Chiller Running Output
CHWS Temperature
Circuit C Heater Temp
Circuit Loading Sequence
Comm Failure Retry Time
Comp A Must Trip Amps
Comp A S1 Config Switch (8->1)
Comp B Must Trip Amps
Comp B S1 Config Switch (8->1)
Comp C Must Trip Amps
Comp C S1 Config Switch (8->1)
Compressor A Disable
Compressor A Hours
Compressor A Hours
Compressor A Output
Compressor A Starts
Compressor A Starts
Compressor B Disable
Compressor B Hours
Compressor B Hours
Compressor B Output
Compressor B Starts
Compressor B Starts
Compressor C Disable
Compressor C Hours
Compressor C Hours
Compressor C Output
Compressor C Starts
Compressor C Starts
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
LINE
READ/
WRITE
CCN TABLE NAME
ISO_CL_A
ISO_CL_B
ISO_CL_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
22
22
22
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
ISO_OP_A
ISO_OP_B
ISO_OP_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
23
23
23
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
ISO_REFA
ISO_REFB
ISO_REFC
Baud rate
flow_sp
lowestsp
Broadcast
Bus
CHIL_S_S
Q_CATO
CAPT_010
CURR_LIM
CURR_LIM
ll_serie
CHIL_OCC
Q_READY
Q_RUN
CHWSTEMP
T_HEAT_C
lead_cir
RETRY_TM
cpa_mtac
cpa_s1_c
cpb_mtac
cpb_s1_c
cpc_mtac
cpc_s1_c
un_cp_a
hr_cp_a
HR_CP_A
Q_CPA
st_cp_a
st_cp_a
un_cp_b
hr_cp_b
HR_CP_B
Q_CPB
st_cp_b
st_cp_b
un_cp_c
hr_cp_c
HR_CP_C
Q_CPC
st_cp_c
st_cp_c
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Service\SERVICE1
MAIN MENU\Service\SERVICE1
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\STATEGEN
MAIN MENU\Maint\LOADFACT
MAIN MENU\Status\GENUNIT
MAIN MENU\Config\MST_SLV
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Config\USER
MAIN MENU\Config\ALARMDEF
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\CP_UNABL
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
MAIN MENU\Status\SERV_TST
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
MAIN MENU\Service\CP_UNABL
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
MAIN MENU\Status\SERV_TST
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
MAIN MENU\Service\CP_UNABL
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
MAIN MENU\Status\SERV_TST
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
21
21
21
9
2
3
10
7
5
46
43
11
24
24
6
41
42
40
38
1
3
2
3
6
7
10
11
2
7
3
3
8
4
3
9
5
5
10
6
4
11
7
7
12
8
RO
RO
RO
RO
RW
RW
RO
RO
RO
RW
RO
RO
RW
RW
RO
RW
RW
RO
RO
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RO
RW
RW
RO
RW
RW
RO
RW
RW
RO
RW
RW
RO
RW
RW
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
Configuration Tables\!CtlrID\PD5_XAXQ
Service Configuration Tables\SERVICE1
Service Configuration Tables\SERVICE1
Configuration Tables\!CtlrID\PD5_XAXQ
Configuration Tables\!CtlrID\PD5_XAXQ
Status Display Tables\GENUNIT
Status Display Tables\QCK_TST1
Status Display Tables\STATEGEN
Maintenance Display Tables\LOADFACT
Status Display Tables\GENUNIT
Configuration Tables\MST_SLV
Status Display Tables\GENUNIT
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Configuration Tables\USER
Configuration Tables\ALARMDEF\ALARMS01
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY2
Service Configuration\CP_UNABL
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
Status Display Tables\SERV_TST
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
Service Configuration\CP_UNABL
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
Status Display Tables\SERV_TST
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
Service Configuration\CP_UNABL
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
Status Display Tables\SERV_TST
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
112
Compressor Output
Circuit A
Circuit B
Circuit C
Compressor Suction Temp
Circuit A
Circuit B
Circuit C
Condenser Entering Fluid
Condenser Flow Status
Condenser Fluid Type
Condenser Leaving Fluid
Condenser Probe Select
Condenser Pump #1 Command
Condenser Pump #1 Hours
Condenser Pump #1 Hours
Condenser Pump #2 Command
Condenser Pump #2 Hours
Condenser Pump #2 Hours
Condenser Pump 1
Condenser Pump 2
Condenser Pumps Rotation
Condenser Pumps Sequence
Condenser Water Val Sel
Control Point
Control Point
Control Type
Controlled Temp Error
Controlled Water Temp
Cool Changeover Setpt
Cooler Entering Fluid
Cooler Entering Fluid
Cooler Exchange DT Cir A
Cooler Exchange DT Cir B
Cooler Exchange DT Cir C
Cooler Flow Setpoint Out
Cooler Flow Switch
Cooler Fluid Type
Cooler Heater Active
Cooler Heater Command
Cooler Heater Delta Spt
Cooler Heater Output
Cooler Heater Select
Cooler Heater Temp
Cooler Leaving Fluid
Cooler Leaving Fluid
Cooler Pinch Ctl Point A
Cooler Pinch Ctl Point B
Cooler Pinch Ctl Point C
Cooler Pump #1 Command
Cooler Pump #1 Hours
Cooler Pump #2 Command
Cooler Pump #2 Hours
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
COMP_A
COMP_B
COMP_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
SUCT_T_A
SUCT_T_B
SUCT_T_C
COND_EWT
CONDFLOW
cond_typ
COND_LWT
condprob
HPUMP_1
hr_hpum1
hr_hpum1
HPUMP_2
hr_hpum2
hr_hpum2
Q_HPMP1
Q_HPMP2
Mode_17
hpump_seq
cond_val
CTRL_PNT
CTRL_PNT
ctr_type
tp_error
CTRL_WT
cauto_sp
COOL_EWT
COOL_EWT
pinch_a
pinch_b
pinch_c
SET_FLOW
FLOW_SW
flui_typ
Mode_06
COOLHEAT
heatersp
Q_CL_HT
heat_sel
T_HEATER
COOL_LWT
COOL_LWT
pinch_spa
pinch_spb
pinch_spc
CPUMP_1
hr_cpum1
CPUMP_2
hr_cpum2
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Service\SERVICE1
MAIN MENU\Status\STATEGEN
MAIN MENU\Service\FACTORY
MAIN MENU\Status\STATEGEN
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
MAIN MENU\Status\STATEGEN
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\MODES
MAIN MENU\Config\USER
MAIN MENU\Service\FACTORY
MAIN MENU\Maint\LOADFACT
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\GENUNIT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Status\GENUNIT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Service\SERVICE1
MAIN MENU\Status\MODES
MAIN MENU\Status\STATEGEN
MAIN MENU\Service\SERVICE1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Service\FACTORY
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STRTHOUR
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STRTHOUR
LINE
READ/
WRITE
CCN TABLE NAME
2
2
2
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
14
14
14
35
14
4
36
26
23
15
11
24
16
12
39
40
18
7
13
5
28
3
7
29
29
33
33
6
13
20
18
12
1
7
26
17
36
12
37
34
34
7
14
21
20
9
21
10
RO
RO
RO
RO
RO
RW
RO
RW
RO
RW
RO
RO
RW
RO
RW
RW
RO
RW
RW
RO
RO
RO
RO
RO
RW
RO
RO
RO
RO
RO
RO
RO
RW
RO
RO
RW
RW
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Service Configuration Tables\SERVICE1
Status Display Tables\STATEGEN
Service Configuration Tables\FACTORY
Status Display Tables\STATEGEN
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
Status Display Tables\STATEGEN
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\MODES
Configuration Tables\USER
Service Configuration Tables\FACTORY
Maintenance Display Tables\LOADFACT
Status Display Tables\GENUNIT
Status Display Tables\GENUNIT
Maintenance Display Tables\LOADFACT
Status Display Tables\GENUNIT
Setpoint Configuration Tables\SETPOINT
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Service Configuration Tables\SERVICE1
Status Display Tables\MODES
Status Display Tables\STATEGEN
Service Configuration Tables\SERVICE1
Status Display Tables\QCK_TST1
Service Configuration Tables\FACTORY
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Status Display Tables\STATEGEN
Status Display Tables\STRTHOUR
Status Display Tables\STATEGEN
Status Display Tables\STRTHOUR
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
113
Cooler Pump Run Status
Cooler Pumps Rotation
Cooler Pumps Sequence
Cooling Ice Setpoint
Cooling Ramp Loading
Cooling Reset Deg. Value
Cooling Reset Select
Cooling Setpoint 1
Cooling Setpoint 2
Cooling/FreeCool Timeout
CPump 1 Ctl Delay (days)
CPump 2 Ctl Delay (days)
Current Alarm 1
Current Alarm 2
Current Alarm 3
Current Alarm 4
Current Alarm 5
Current At 100% Load A
Current At 100% Load B
Current At 100% Load C
Current At 30% Load A
Current At 30% Load B
Current At 30% Load C
Current Control
Current Cooling Power
Current Full Reset Value
Current Full Reset Value
Current Limit at 100%
Current Limit Select
Current Mode (1=occup.)
Current Mode (1=occup.)
Current No Reset Value
Current No Reset Value
Current Occup Period #
Current Occup Period #
Current Occupied Time
Current Occupied Time
Current Phase 1 Comp A
Current Phase 1 Comp B
Current Phase 1 Comp C
Current Phase 2 Comp A
Current Phase 2 Comp B
Current Phase 2 Comp C
Current Phase 3 Comp A
Current Phase 3 Comp B
Current Phase 3 Comp C
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
CPUMPDEF
Mode_07
cpump_seq
ice_sp
cramp_sp
cr_deg
cr_sel
csp1
csp2
fc_tmout
cpump1_c
cpump2_c
alarm_1
alarm_2
alarm_3
alarm_4
alarm_5
cur100_a
cur100_b
cur100_c
cur_30_a
cur_30_b
cur_30_c
on_ctrl
cool_pwr
v_cr_fu
v_hr_fu
curr_ful
curr_sel
MODE
MODE
v_cr_no
v_hr_no
PER-NO
PER-NO
STRTTIME
STRTTIME
cpa_cur1
cpb_cur1
cpc_cur1
cpa_cur2
cpb_cur2
cpc_cur2
cpa_cur3
cpb_cur3
cpc_cur3
TOUCH PILOT PATH
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\MODES
MAIN MENU\Config\USER
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Config\USER
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Status\FREECOOL
MAIN MENU\Service\MAINTCFG
MAIN MENU\Service\MAINTCFG
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\GENUNIT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\FREECOOL
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Config\USER
MAIN MENU\Config\USER
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Maint\CUR_PHAS
MAIN MENU\Maint\CUR_PHAS
MAIN MENU\Maint\CUR_PHAS
MAIN MENU\Maint\CUR_PHAS
MAIN MENU\Maint\CUR_PHAS
MAIN MENU\Maint\CUR_PHAS
MAIN MENU\Maint\CUR_PHAS
MAIN MENU\Maint\CUR_PHAS
MAIN MENU\Maint\CUR_PHAS
LINE
13
8
8
4
14
13
19
2
3
7
5
6
14
15
16
17
18
15
16
17
12
13
14
4
4
10
24
31
30
1
1
9
23
2
2
5
5
1
4
7
2
5
8
3
6
9
READ/
WRITE
RO
RO
RW
RW
RW
RW
RW
RW
RW
RO
RW
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RW
RW
RW
RW
RO
RO
RW
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
CCN TABLE NAME
Status Display Tables\STATEGEN
Status Display Tables\MODES
Configuration Tables\USER
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Configuration Tables\USER
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Status Display Tables\FREECOOL
Service Configuration Tables\MAINTCFG
Service Configuration Tables\MAINTCFG
Status Display Tables\GENUNIT
Status Display Tables\GENUNIT
Status Display Tables\GENUNIT
Status Display Tables\GENUNIT
Status Display Tables\GENUNIT
Maintenance Display Tables\LOADFACT
Maintenance Display Tables\LOADFACT
Maintenance Display Tables\LOADFACT
Maintenance Display Tables\LOADFACT
Maintenance Display Tables\LOADFACT
Maintenance Display Tables\LOADFACT
Status Display Tables\STATEGEN
Status Display Tables\FREECOOL
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Configuration Tables\USER
Configuration Tables\USER
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Maintenance Display Tables\CUR_PHASE
Maintenance Display Tables\CUR_PHASE
Maintenance Display Tables\CUR_PHASE
Maintenance Display Tables\CUR_PHASE
Maintenance Display Tables\CUR_PHASE
Maintenance Display Tables\CUR_PHASE
Maintenance Display Tables\CUR_PHASE
Maintenance Display Tables\CUR_PHASE
Maintenance Display Tables\CUR_PHASE
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
114
Current Setpoint
Current Unoccupied Time
Current Unoccupied Time
Current Z Multiplier Val
Customer Shutdown Out
Daylight Sav Ent Day of Week (1=Monday)
Daylight Sav Ent Month
Daylight Sav Ent Week of Month
Daylight Sav Leaving Day of Week (1=Monday)
Daylight Sav Leaving Month
Daylight Sav Leaving Week of Month
Daylight Saving Select
Decription
Defrost Active On Cir A
Defrost Active On Cir B
Defrost Active?
Circuit A
Circuit B
Defrost Duration
Circuit A
Circuit B
Defrost Fan Offset Cal A
Defrost Fan Offset Cal B
Defrost Fan Start Cal A
Defrost Fan Start Cal B
Defrost Number
Circuit A
Circuit B
Defrost Number
Circuit A
Circuit B
Defrost Temperature
Circuit A
Circuit B
Delta - Reference Delta
Circuit A
Circuit B
Delta: OAT - Mean SST
Circuit A
Circuit B
Delta T Full Reset Value
Delta T Full Reset Value
Delta T No Reset Value
Delta T No Reset Value
Demand Limit Active
Demand Limit Type Select
Deri PID Gain Varifan
DGT Cool Solenoid
Circuit A
Circuit B
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
SP
ENDTIME
ENDTIME
zm
Q_SHUT
startdow
startmon
startwom
stopdow
stopmon
stopwom
dayl_sel
DevDesc
Mode_19
Mode_20
TOUCH PILOT PATH
MAIN MENU\Status\GENUNIT
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Maint\LOADFACT
MAIN MENU\Status\QCK_TST1
MAIN MENU\Config\BRODEFS
MAIN MENU\Config\BRODEFS
MAIN MENU\Config\BRODEFS
MAIN MENU\Config\BRODEFS
MAIN MENU\Config\BRODEFS
MAIN MENU\Config\BRODEFS
MAIN MENU\Config\BRODEFS
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
READ/
LINE WRITE
31
RW
6
RO
6
RO
18
RO
47
RW
10
RW
9
RW
11
RW
14
RW
13
RW
15
RW
7
RW
1
RW
20
RO
21
RO
CCN TABLE NAME
Status Display Tables\GENUNIT
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Maintenance Display Tables\LOADFACT
Status Display Tables\QCK_TST1
Configuration Tables\BRODEFS\BROCASTS
Configuration Tables\BRODEFS\BROCASTS
Configuration Tables\BRODEFS\BROCASTS
Configuration Tables\BRODEFS\BROCASTS
Configuration Tables\BRODEFS\BROCASTS
Configuration Tables\BRODEFS\BROCASTS
Configuration Tables\BRODEFS\BROCASTS
Configuration Tables\!CtlrID\PD5_XAXQ
Status Display Tables\MODES
Status Display Tables\MODES
mode[19]
mode[20]
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
4
21
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
defr_dua
defr_dub
def_of_a
def_of_b
def_ca_a
def_ca_b
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
6
23
16
33
15
32
RO
RO
RO
RO
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
nb_def_a
nb_def_b
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
6
7
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
nb_def_a
nb_def_b
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
3
4
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
DEFRT_A
DEFRT_B
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
5
22
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
delt_v_a
delt_v_b
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
13
30
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
delt_a
delt_b
dt_cr_fu
dt_hr_fu
dt_cr_no
dt_hr_no
Mode_04
lim_sel
hd_dg
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Status\MODES
MAIN MENU\Config\USER
MAIN MENU\Service\SERVICE1
11
28
8
22
7
21
5
24
8
RO
RO
RW
RW
RW
RW
RO
RW
RW
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Status Display Tables\MODES
Configuration Tables\USER
Service Configuration Tables\SERVICE1
Q_CDGT_A
Q_CDGT_B
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
21
28
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
115
DGT Cooling Solenoid
Circuit A
Circuit B
Circuit C
Discharge Gas Temp
Circuit A
Circuit B
Circuit C
Discharge Pressure
Circuit A
Circuit B
Circuit C
Differential Water Temp
Discharge A Gas Limit
Discharge A Temp Average
Discharge A Temp Rate
Discharge B Gas Limit
Discharge B Temp Average
Discharge B Temp Rate
Discharge C Gas Limit
Discharge C Temp Average
Discharge C Temp Rate
Discharge Superheat A
Discharge Superheat B
Discharge Superheat C
DLY 3 - Cooler Pump 1 (days)
DLY 4 - Cooler Pump 2 (days)
DLY 5 - Condenser Pump 1 (days)
DLY 6 - Condenser Pump 2 (days)
DLY 7 - Water Filter (days)
DLY 8 - Cp A Oil Filter (days)
DLY 9 - Cp B Oil Filter (days)
DLY 10 - Cp C Oil Filter (days)
DX Cooler Select
Economizer A Steps Numb
Economizer B Steps Numb
Economizer C Steps Numb
Economizer Position A
Economizer Position B
Economizer Position C
Economizer SH Setpoint A
Economizer SH Setpoint A
Economizer SH Setpoint B
Economizer SH Setpoint B
Economizer SH Setpoint C
Economizer SH Setpoint C
Economizer Superheat A
Economizer Superheat B
Economizer Superheat C
Economizer EXV Pos
Circuit A
Circuit B
Circuit C
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
GASCOOLA
GASCOOLB
GASCOOLC
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
DGT_A
DGT_B
DGT_C
LINE
READ/
WRITE
CCN TABLE NAME
8
8
8
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
10
10
10
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
DP_A
DP_B
DP_C
diff_wt
sdtlim_a
sdt_m_a
sdt_mr_a
sdtlim_b
sdt_m_b
sdt_mr_b
sdtlim_c
sdt_m_c
sdt_mr_c
DSH_A
DSH_B
DSH_C
cpump1_m
cpump2_m
hpump1_m
hpump2_m
wfilte_m
ofilta_m
ofiltb_m
ofiltc_m
dxcooler
eco_cnfa
eco_cnfb
eco_cnfc
EXV_EC_A
EXV_EC_B
EXV_EC_C
ecsh_spa
esh_sp_a
ecsh_spb
esh_sp_b
ecsh_spc
esh_sp_c
eco_sha
eco_shb
eco_shc
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
MAIN MENU\Maint\LOADFACT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\SERMAINT
MAIN MENU\Maint\SERMAINT
MAIN MENU\Maint\SERMAINT
MAIN MENU\Maint\SERMAINT
MAIN MENU\Maint\SERMAINT
MAIN MENU\Maint\SERMAINT
MAIN MENU\Maint\SERMAINT
MAIN MENU\Maint\SERMAINT
MAIN MENU\Service\FACTORY
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY2
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Service\SERVICE1
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Service\SERVICE1
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Service\SERVICE1
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
3
3
3
3
3
1
2
7
5
6
11
9
10
3
10
17
10
11
12
13
14
15
16
17
16
22
23
24
25
29
33
27
21
31
22
35
23
26
30
34
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RW
RW
RW
RW
RO
RO
RO
RO
RW
RO
RW
RO
RW
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
Maintenance Display Tables\LOADFACT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\SERMAINT
Maintenance Display Tables\SERMAINT
Maintenance Display Tables\SERMAINT
Maintenance Display Tables\SERMAINT
Maintenance Display Tables\SERMAINT
Maintenance Display Tables\SERMAINT
Maintenance Display Tables\SERMAINT
Maintenance Display Tables\SERMAINT
Service Configuration Tables\FACTORY
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY2
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Service Configuration Tables\SERVICE1
Maintenance Display Tables\EXV_CTRL
Service Configuration Tables\SERVICE1
Maintenance Display Tables\EXV_CTRL
Service Configuration Tables\SERVICE1
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Q_ECO_A
Q_ECO_B
Q_ECO_C
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
6
7
8
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
116
Economizer Gas Temp
Circuit A
Circuit B
Circuit C
Economizer Pressure
Circuit A
Circuit B
Circuit C
EHS Ctrl Override
Elec Stage OAT Threshold
Electric Heat Active
Electrical Box Interlock
Electrical Heat Stage
Electrical Heat Stages
Electrical Pulldown Time
Electrical Pulldown?
Element
Emergency Stop
EMM NRCP2 Board
Energy Management Module
Entering Fluid Control
Estimated FreeCool Power
Exchanger Frost Factor
Circuit A
Circuit B
External Temperature
EXV A Maximum Steps Numb
EXV A Superheat Setpoint
EXV B Maximum Steps Numb
EXV B Superheat Setpoint
EXV Board Circuit A
EXV Board Circuit B
EXV Board Circuit C
EXV C Maximum Steps Numb
EXV C Superheat Setpoint
EXV MOP Setpoint
EXV Override Circuit A
EXV Override Circuit A
EXV Override Circuit B
EXV Override Circuit B
EXV Override Circuit C
EXV Override Circuit C
EXV Position Circuit A
EXV Position Circuit B
EXV Position Circuit C
EXV Position
Circuit A
Circuit B
Circuit C
EXV Position
Circuit A
Circuit B
Circuit C
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
LINE
READ/
WRITE
CCN TABLE NAME
ECO_TP_A
ECO_TP_B
ECO_TP_C
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
11
11
11
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
ECON_P_A
ECON_P_B
ECON_P_C
over_ehs
ehs_th
Mode_15
ELEC_BOX
EHS_STEP
ehs_sel
ehs_pull
ehspulld
Element
EMSTOP
EMM_NRCP
emm_nrcp
ewt_opt
fc_pwr
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
MAIN MENU\Maint\LOADFACT
MAIN MENU\Config\USER
MAIN MENU\Status\MODES
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Service\FACTORY
MAIN MENU\Config\USER
MAIN MENU\Maint\LOADFACT
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Status\GENUNIT
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Service\FACTORY
MAIN MENU\Service\SERVICE1
MAIN MENU\Status\FREECOOL
5
5
5
22
34
16
16
19
16
36
24
8
32
9
17
5
5
RO
RO
RO
RO
RW
RO
RO
RO
RW
RW
RO
RO
RO
RO
RW
RW
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
Maintenance Display Tables\LOADFACT
Configuration Tables\USER
Status Display Tables\MODES
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Service Configuration Tables\FACTORY
Configuration Tables\USER
Maintenance Display Tables\LOADFACT
Configuration Tables\!CtlrID\PD5_XAXQ
Status Display Tables\GENUNIT
Maintenance Display Tables\BOARD_PN
Service Configuration Tables\FACTORY
Service Configuration Tables\SERVICE1
Status Display Tables\FREECOOL
frost_a
frost_b
OAT
exva_max
sh_sp_a
exvb_max
sh_sp_b
EXV_BRD1
EXV_BRD2
EXV_BRD3
exvc_max
sh_sp_c
mop_sp
oc_eco_a
ov_exv_a
oc_eco_b
ov_exv_b
oc_eco_c
ov_exv_c
EXV_A
EXV_B
EXV_C
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Status\GENUNIT
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\SERVICE1
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\SERVICE1
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\SERVICE1
MAIN MENU\Service\SERVICE1
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
2
19
30
18
9
19
10
1
2
3
20
11
15
28
8
32
15
36
22
2
9
16
RO
RO
RO
RW
RW
RW
RW
RO
RO
RO
RW
RW
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
Status Display Tables\GENUNIT
Service Configuration Tables\FACTORY2
Service Configuration Tables\SERVICE1
Service Configuration Tables\FACTORY2
Service Configuration Tables\SERVICE1
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Service Configuration Tables\FACTORY2
Service Configuration Tables\SERVICE1
Service Configuration Tables\SERVICE1
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Q_EXVA
Q_EXVB
Q_EXVC
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
3
4
5
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
EXV_A
EXV_B
EXV_C
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
15
15
15
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
117
EXV Position
Circuit A
Circuit B
Circuit C
Factory Password
Fan #1 Hours
Circuit A
Circuit B
Circuit C
Fan #1 Hours
Circuit A
Circuit B
Circuit C
Fan #2 Hours
Circuit A
Circuit B
Circuit C
Fan #2 Hours
Circuit A
Circuit B
Circuit C
Fan #3 Hours
Circuit A
Circuit B
Circuit C
Fan #3 Hours
Circuit A
Circuit B
Circuit C
Fan #4 Hours
Circuit A
Circuit B
Circuit C
Fan #4 Hours
Circuit A
Circuit B
Circuit C
Fan #5 Hours
Circuit A
Circuit B
Circuit C
Fan #5 Hours
Circuit A
Circuit B
Circuit C
Fan #6 Hours
Circuit A
Circuit B
Circuit C
Fan #6 Hours
Circuit A
Circuit B
Circuit C
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
LINE
READ/
WRITE
CCN TABLE NAME
EXV_A
EXV_B
EXV_C
fac_pass
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Service\FACTORY
20
30
40
19
RO
RO
RO
RW
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Service Configuration Tables\FACTORY
hr_fana1
hr_fanb1
hr_fanc1
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
8
18
28
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hr_fana1
hr_fanb1
hr_fanc1
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
5
15
25
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
hr_fana2
hr_fanb2
hr_fanc2
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
9
19
29
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hr_fana2
hr_fanb2
hr_fanc2
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
6
16
26
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
hr_fana3
hr_fanb3
hr_fanc3
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
10
20
30
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hr_fana3
hr_fanb3
hr_fanc3
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
7
17
27
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
hr_fana4
hr_fanb4
hr_fanc4
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
11
21
31
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hr_fana4
hr_fanb4
hr_fanc4
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
8
18
28
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
hr_fana5
hr_fanb5
hr_fanc5
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
12
22
32
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hr_fana5
hr_fanb5
hr_fanc5
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
9
19
29
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
hr_fana6
hr_fanb6
hr_fanc6
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
13
23
33
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hr_fana6
hr_fanb6
hr_fanc6
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
10
20
30
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
118
Fan #7 Hours
Circuit A
Circuit B
Circuit C
Fan #7 Hours
Circuit A
Circuit B
Circuit C
Fan #8 Hours
Circuit A
Circuit B
Circuit C
Fan #8 Hours
Circuit A
Circuit B
Circuit C
Fan #9 Hours
Circuit A
Circuit B
Circuit C
Fan #9 Hours
Circuit A
Circuit B
Circuit C
Fan #10 Hours
Circuit A
Circuit B
Circuit C
Fan #10 Hours
Circuit A
Circuit B
Circuit C
Fan Cycle Counter
Circuit A
Circuit B
Circuit C
Fan Output DO #1
Circuit A
Circuit B
Circuit C
Fan Output DO #2
Circuit A
Circuit B
Circuit C
Fan Output DO #3
Circuit A
Circuit B
Circuit C
Fan Output DO #4
Circuit A
Circuit B
Circuit C
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
LINE
READ/
WRITE
CCN TABLE NAME
hr_fana7
hr_fanb7
hr_fanc7
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
14
24
34
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hr_fana7
hr_fanb7
hr_fanc7
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
11
21
31
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
hr_fana8
hr_fanb8
hr_fanc8
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
15
25
35
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hr_fana8
hr_fanb8
hr_fanc8
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
12
22
32
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
hr_fana9
hr_fanb9
hr_fanc9
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
16
26
36
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hr_fana9
hr_fanb9
hr_fanc9
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
13
23
33
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
hrfana10
hrfanb10
hrfanc10
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Service\UPDHRFAN
17
27
37
RW
RW
RW
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
Service Configuration Tables\UPDHRFAN
hrfana10
hrfanb10
hrfanc10
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
14
24
34
RO
RO
RO
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
fancyc_a
fancyc_b
fancyc_c
MAIN MENU\Maint\FANCTRL
MAIN MENU\Maint\FANCTRL
MAIN MENU\Maint\FANCTRL
3
7
11
RO
RO
RO
Maintenance Display Tables\FANCTRL
Maintenance Display Tables\FANCTRL
Maintenance Display Tables\FANCTRL
fan_a1
fan_b1
fan_c1
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
11
11
11
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
fan_a2
fan_b2
fan_c2
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
12
12
12
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
fan_a3
fan_b3
fan_c3
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
13
13
13
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
fan_a4
fan_b4
fan_c4
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
14
14
14
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
119
Fan Output DO #5
Circuit A
Circuit B
Circuit C
Fan Output DO #6
Circuit A
Circuit B
Circuit C
Fan Output DO #7
Circuit A
Circuit B
Circuit C
Fan Output DO #8
Circuit A
Circuit B
Circuit C
Fan Sequence Started?
Circuit A
Circuit B
Fan Stages
Circuit A
Circuit B
Circuit C
Fan Staging Number
Circuit A
Circuit B
Circuit C
Fan Staging Number
Circuit A
Circuit B
Circuit C
Flow Checked if C Pump Off
Free Cool A Ball Valve
Free Cool A EXV Position
Free Cool B Ball Valve
Free Cool B EXV Position
Free Cool Conditions OK?
Free Cool Pump A Hours
Free Cool Pump B Hours
Free Cool Request?
Free Cooling A Pump Hours
Free Cooling Active
Free Cooling Active
Circuit A
Circuit B
Circuit C
Free Cooling B Pump Hours
Free Cooling Disable
Free Cooling Disable Sw
Free Cooling Disable?
Free Cooling Heater
Free Cooling OAT Limit
Free Cooling Select
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
LINE
READ/
WRITE
CCN TABLE NAME
fan_a5
fan_b5
fan_c5
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
15
15
15
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
fan_a6
fan_b6
fan_c6
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
16
16
16
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
fan_a7
fan_b7
fan_c7
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
17
17
17
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
fan_a7
fan_b7
fan_c7
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
17
17
17
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
def_fa_a
def_fa_b
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
7
24
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
Q_FAN_A
Q_FAN_B
Q_FAN_C
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
9
10
11
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
FAN_ST_A
FAN_ST_B
FAN_ST_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
19
19
19
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
FAN_ST_A
FAN_ST_B
FAN_ST_C
pump_loc
Q_FCBVL_A
Q_FCEXVA
Q_FCBVL_B
Q_FCEXVB
fc_ready
hr_fcm_a
hr_fcm_b
fc_reqst
hr_fcp_a
Mode_13
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Config\USER
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FANHOURS
MAIN MENU\Status\FREECOOL
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Status\MODES
13
23
33
17
18
16
19
17
8
1
2
9
4
14
RO
RO
RO
RW
RO
RO
RO
RO
RO
RO
RO
RO
RW
RO
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Configuration Tables\USER
Status Display Tables\QCK_TST2
Status Display Tables\QCK_TST2
Status Display Tables\QCK_TST2
Status Display Tables\QCK_TST2
Status Display Tables\FREECOOL
Status Display Tables\FANHOURS
Status Display Tables\FANHOURS
Status Display Tables\FREECOOL
Service Configuration Tables\UPDHRFAN
Status Display Tables\MODES
FC_ON_A
FC_ON_B
FC_ON_C
hr_fcp_b
FC_DSBLE
FC_SW
FC_DSBLE
Q_FC_HTR
free_oat
freecool
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Service\UPDHRFAN
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\QCK_TST2
MAIN MENU\Config\USER
MAIN MENU\Service\FACTORY
12
22
32
5
12
6
2
15
33
11
RO
RO
RO
RW
RW
RO
RO
RO
RW
RW
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Service Configuration Tables\UPDHRFAN
Status Display Tables\GENUNIT
Status Display Tables\STATEGEN
Status Display Tables\FREECOOL
Status Display Tables\QCK_TST2
Configuration Tables\USER
Service Configuration Tables\FACTORY
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
120
Frost Integrator Gain
Circuit A
Circuit B
Head Press Speed
Circuit A
Circuit B
Circuit C
HEAT RECLAIM CIRCUIT A
HEAT RECLAIM CIRCUIT B
Heat Reclaim Select
Heat Reclaim Select
Heat/Cool Select
Heat/Cool Status
Heating Changeover Setpt
Heating Low EWT Lockout
Heating OAT Threshold
Heating Ramp Loading
Heating Reset Deg. Value
Heating Reset Select
Heating Setpoint 1
Heating Setpoint 2
High Condensing Select
High DGT Circuit A
High DGT Circuit B
High DGT Circuit C
High Pres Override Cir A
High Pres Override Cir B
High Pres Override Cir C
High Pressure Threshold
High Tiers Display Selec
Holiday Duration (days)
Holiday Start Day
Holiday Start Month
Hot Gas Bypass Select
Head Press Actuator Pos
Circuit A
Circuit B
Circuit C
Heater Ball Valve
Circuit A
Circuit B
Circuit C
Hot Gas Bypass Output
Circuit A
Circuit B
Circuit C
Hot Gas Bypass
Circuit A
Circuit B
Circuit C
HPump 1 Ctl Delay (days)
HPump 2 Ctl Delay (days)
HR Condenser Heater
Ice Done Storage Switch
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
LINE
READ/
WRITE
CCN TABLE NAME
fr_int_a
fr_int_b
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
14
31
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
Q_VFANA
Q_VFANB
Q_VFANC
—
—
RECL_SEL
RECL_SET
HC_SEL
HEATCOOL
hauto_sp
Mode_16
heat_th
hramp_sp
hr_deg
hr_sel
hsp1
hsp2
highcond
Mode_24
Mode_25
Mode_26
Mode_27
Mode_28
Mode_29
hp_th
highdisp
HOL-LEN
HOL-DAY
HOL-MON
hgbp_sel
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\GENUNIT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Status\MODES
MAIN MENU\Config\USER
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Config\USER
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Service\FACTORY
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Service\SERVICE1
MAIN MENU\Service\FACTORY
MAIN MENU\Config\HOLIDAY\HOLDY_01
MAIN MENU\Config\HOLIDAY\HOLDY_01
MAIN MENU\Config\HOLIDAY\HOLDY_01
MAIN MENU\Service\FACTORY
12
13
14
9
19
1
11
9
8
30
17
32
26
25
20
17
18
24
25
26
27
28
29
30
16
18
3
2
1
14
RW
RW
RW
RO
RO
RO
RW
RW
RO
RW
RO
RW
RW
RW
RW
RW
RW
RW
RO
RO
RO
RO
RO
RO
RW
RW
RW
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\GENUNIT
Status Display Tables\GENUNIT
Status Display Tables\GENUNIT
Setpoint Configuration Tables\SETPOINT
Status Display Tables\MODES
Configuration Tables\USER
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Configuration Tables\USER
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Service Configuration Tables\FACTORY
Status Display Tables\MODES
Status Display Tables\MODES
Status Display Tables\MODES
Status Display Tables\MODES
Status Display Tables\MODES
Status Display Tables\MODES
Service Configuration Tables\SERVICE1
Service Configuration Tables\FACTORY
Configuration Tables\HOLIDAY\HOLDY_01
Configuration Tables\HOLIDAY\HOLDY_01
Configuration Tables\HOLIDAY\HOLDY_01
Service Configuration Tables\FACTORY
hd_pos_a
hd_pos_b
hd_pos_c
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
16
16
16
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
Q_BVL_A
Q_BVL_B
Q_BVL_C
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
19
26
33
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
HGBP_A
HGBP_B
HGBP_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
9
9
9
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
Q_HGBP_A
Q_HGBP_B
Q_HGBP_C
hpump1_c
hpump2_c
Q_CD_HT
ICE_SW
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Service\MAINTCFG
MAIN MENU\Service\MAINTCFG
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\STATEGEN
20
27
34
7
8
12
11
RW
RW
RW
RW
RW
RW
RO
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Service Configuration Tables\MAINTCFG
Service Configuration Tables\MAINTCFG
Status Display Tables\QCK_TST2
Status Display Tables\STATEGEN
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
121
Ice Mode Enable
Ice Mode in Effect
Int PID Gain Varifan
Lag Capacity Limit Value
Lag Minimum Running Time
Lag Start Delay
Lag Start Timer
Lag Unit Pump Control
Language Selection
Lead Lag Select
Lead Pulldown Time
Lead Pulldown?
Lead Unit is the:
Lead/Lad Changeover?
Lead/Lag Balance Delta
Lead/Lag Hours Delta
Limit 4-20mA Signal
Limit Switch 1 Status
Limit Switch 2 Status
Load/Unload Factor
Location
Low Suction Circuit A
Low Suction Circuit B
Low Suction Circuit C
Low Superheat Circuit A
Low Superheat Circuit B
Low Superheat Circuit C
LWT-OAT Delta
mA For 0% Demand Limit
mA For 100% Demand Limit
Machine Operating Hours
Machine Operating Hours
Machine Starts
Machine Starts Number
Master Control Type
Master Control Type
Master Slave Active
Master/Slave Ctrl Active
Master/Slave Error
Master/Slave Select
Max Available Capacity?
Max Condenser LWT = 45C
MCHX Exchanger Select
Metric Display on STDU
Minutes Left for Start
Model Number
Must Trip Amps
Must Trip Amps
Must Trip Amps
Mean SST Calculation
Circuit A
Circuit B
Motor Current
Circuit A
Circuit B
Circuit C
LEGEND
RO — Read Only
MAIN MENU\Config\USER
MAIN MENU\Status\MODES
MAIN MENU\Service\SERVICE1
MAIN MENU\Status\GENUNIT
MAIN MENU\Config\MST_SLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Config\MST_SLV
MAIN MENU\Config\MST_SLV
MAIN MENU\Config\DISPCONF
MAIN MENU\Config\MST_SLV
MAIN MENU\Config\MST_SLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Config\MST_SLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Maint\LOADFACT
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Status\MODES
MAIN MENU\Status\FREECOOL
MAIN MENU\Config\USER
MAIN MENU\Config\USER
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Status\STRTHOUR
MAIN MENU\Config\MST_SLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Status\MODES
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Config\MST_SLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Service\FACTORY
MAIN MENU\Service\FACTORY
MAIN MENU\Config\DISPCONF
MAIN MENU\Status\GENUNIT
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
42
19
7
22
20
8
17
21
2
12
18
11
5
10
16
9
42
8
9
19
2
22
23
24
31
32
33
3
29
28
5
1
6
2
7
3
12
4
12
3
13
25
15
1
7
4
12
16
20
READ/
WRITE
RW
RO
RW
RO
RW
RO
RW
RW
RW
RW
RW
RO
RO
RO
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RW
RW
RW
RO
RW
RO
RW
RO
RO
RO
RO
RW
RO
RW
RW
RW
RO
RO
RO
RO
RO
sst_dm_a
sst_dm_b
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
10
27
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
CURREN_A
CURREN_B
CURREN_C
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
8
8
8
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
TOUCH PILOT
POINT NAME
ice_cnfg
Mode_18
hd_ig
LAG_LIM
lag_mini
l_strt_d
lstr_tim
lag_pump
LANGUAGE
lead_sel
lead_pul
ll_pull
lead_sel
ll_chang
ll_bal_d
ll_hr_d
LIM_ANAL
LIM_SW1
LIM_SW2
smz
Location
Mode_21
Mode_22
Mode_23
Mode_30
Mode_31
Mode_32
fc_delta
lim_ze
lim_mx
hr_mach
HR_MACH
st_mach
st_mach
ms_ctrl
ms_ctrl
Mode_11
ms_activ
ms_error
ms_sel
cap_max
max_clwt
mchx_sel
DISPUNIT
min_left
ModelNum
cpa_mtam
cpb_mtam
cpc_mtam
TOUCH PILOT PATH
LINE
RW — Read/Write
CCN TABLE NAME
Configuration Tables\USER
Status Display Tables\MODES
Service Configuration Tables\SERVICE1
Status Display Tables\GENUNIT
Configuration Tables\MST_SLV
Maintenance Display Tables\MSTSLAVE
Configuration Tables\MST_SLV
Configuration Tables\MST_SLV
Configuration Tables\DISPCONF
Configuration Tables\MST_SLV
Configuration Tables\MST_SLV
Maintenance Display Tables\MSTSLAVE
Maintenance Display Tables\MSTSLAVE
Maintenance Display Tables\MSTSLAVE
Configuration Tables\MST_SLV
Maintenance Display Tables\MSTSLAVE
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Maintenance Display Tables\LOADFACT
Configuration Tables\!CtlrID\PD5_XAXQ
Status Display Tables\MODES
Status Display Tables\MODES
Status Display Tables\MODES
Status Display Tables\MODES
Status Display Tables\MODES
Status Display Tables\MODES
Status Display Tables\FREECOOL
Configuration Tables\USER
Configuration Tables\USER
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
Service Configuration Tables\UPDTHOUR
Status Display Tables\STRTHOUR
Configuration Tables\MST_SLV
Maintenance Display Tables\MSTSLAVE
Status Display Tables\MODES
Maintenance Display Tables\MSTSLAVE
Maintenance Display Tables\MSTSLAVE
Configuration Tables\MST_SLV
Maintenance Display Tables\MSTSLAVE
Service Configuration Tables\FACTORY
Service Configuration Tables\FACTORY
Configuration Tables\DISPCONF
Status Display Tables\GENUNIT
Configuration Tables\!CtlrID\PD5_XAXQ
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
122
Motor Temperature
Circuit A
Circuit B
Circuit C
Next Sequence Allowed in
Circuit A
Circuit B
Oil Heater
Circuit A
Circuit B
Circuit C
Oil Heater Output
Circuit A
Circuit B
Circuit C
Oil Level Input
Circuit A
Circuit B
Circuit C
Oil Pressure
Circuit A
Circuit B
Circuit C
Oil Pressure Difference
Circuit A
Circuit B
Circuit C
Oil Solenoid
Circuit A
Circuit B
Circuit C
Oil Solenoid Output
Circuit A
Circuit B
Circuit C
Optimal Fan Count
Circuit A
Circuit B
Circuit C
Override State
Circuit A
Circuit B
Percent Total Capacity
Circuit A
Circuit B
Circuit C
Pump Differential Press.
Circuit A
Circuit B
Circuit C
Pump Inlet Pressure
Circuit A
Circuit B
Circuit C
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
LINE
READ/
WRITE
CCN TABLE NAME
CP_TMP_A
CP_TMP_B
CP_TMP_C
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
9
9
9
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
def_se_a
def_se_b
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
20
20
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
Q_HT_A
Q_HT_B
Q_HT_C
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
15
22
29
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
OIL_HT_A
OIL_HT_B
OIL_HT_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
5
5
5
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
OIL_L_A
OIL_L_B
OIL_L_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
7
7
7
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
OP_A
OP_B
OP_C
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
6
6
6
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
DOP_A
DOP_B
DOP_C
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
7
7
7
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
Q_OILS_A
Q_OILS_B
Q_OILS_C
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
16
23
30
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
OIL_SL_A
OIL_SL_B
OIL_SL_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
6
6
6
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
fancop_a
fancop_b
fancop_c
MAIN MENU\Maint\FANCTRL
MAIN MENU\Maint\FANCTRL
MAIN MENU\Maint\FANCTRL
4
8
12
RO
RO
RO
Maintenance Display Tables\FANCTRL
Maintenance Display Tables\FANCTRL
Maintenance Display Tables\FANCTRL
over_d_a
over_d_b
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
8
25
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
CAPA_T
CAPB_T
CAPC_T
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
2
2
2
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
fc_dp_a
fc_dp_b
fc_dp_c
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
19
29
39
RO
RO
RO
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
fc_inp_a
fc_inp_b
fc_inp_c
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
17
27
37
RO
RO
RO
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
123
Pump Inlet Pressure
Circuit A
Circuit B
Circuit C
Pump Outlet Pressure
Circuit A
Circuit B
Circuit C
NB Fans on Varifan Cir A
NB Fans on Varifan Cir B
NB Fans on Varifan Cir C
Next Occupied Day
Next Occupied Day
Next Occupied Time
Next Occupied Time
Next Session Allowed In
Next Unoccupied Day
Next Unoccupied Day
Next Unoccupied Time
Next Unoccupied Time
Night Control Capacity Limit
Night Control End Hour
Night Control Start Hour
Night Low Noise Active
OAT Broadcast Bus #
OAT Broadcast Element #
OAT Full Reset Value
OAT Full Reset Value
OAT No Reset Value
OAT No Reset Value
Occupied From
Occupied Override Switch
Occupied To
Oil Filter A Ctrl (days)
Oil Filter B Ctrl (days)
Oil Filter C Ctrl (days)
On/Off - Remote Switch
OP WARN 1- Refrigerant Charge
OP WARN 2 - Water Loop Size
Operating Type
Optional Space temp
Pass for All User Config
Percent Total Capacity
Period # DOW (MTWTFSSH)
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
fc_inp_a
fc_inp_b
fc_inp_c
fc_oup_a
fc_oup_b
fc_oup_c
varfan_a
varfan_b
varfan_c
NXTOCDAY
NXTOCDAY
NXTOCTIM
NXTOCTIM
fc_next
NXTUNDAY
NXTUNDAY
NXTUNTIM
NXTUNTIM
nh_limit
nh_end
nh_start
Mode_09
oatbusnm
oatlocad
oatcr_fu
oathr_fu
oatcr_no
oathr_no
OCCTOD#
OCC_OVSW
UNOCTOD#
oilfil_a
oilfil_b
oilfil_c
ONOFF_SW
charge_m
wloop_m
OPER_TYP
SPACETMP
all_pass
CAP_T
DOW#
LINE
READ/
WRITE
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
17
27
37
RO
RO
RO
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Service\FACTORY
MAIN MENU\Service\FACTORY
MAIN MENU\Service\FACTORY
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Status\FREECOOL
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Config\USER
MAIN MENU\Config\USER
MAIN MENU\Config\USER
MAIN MENU\Status\MODES
MAIN MENU\Config\BRODEFS
MAIN MENU\Config\BRODEFS
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Schedule\OCCPC01S
MAIN MENU\Status\STATEGEN
MAIN MENU\Schedule\OCCPC01S
MAIN MENU\Service\MAINTCFG
MAIN MENU\Service\MAINTCFG
MAIN MENU\Service\MAINTCFG
MAIN MENU\Status\STATEGEN
MAIN MENU\Maint\SERMAINT
MAIN MENU\Maint\SERMAINT
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\STATEGEN
MAIN MENU\Config\USER
MAIN MENU\Status\GENUNIT
MAIN MENU\Schedule\OCCPC01S
18
28
38
5
6
7
7
7
8
8
6
9
9
10
10
41
40
39
10
4
5
6
20
5
19
3
10
4
10
11
12
2
6
7
2
39
44
20
2
RO
RO
RO
RW
RW
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RW
RW
RW
RO
RW
RW
RW
RW
RW
RW
RO
RO
RO
RW
RW
RW
RO
RO
RO
RO
RO
RW
RO
RO
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Service Configuration Tables\FACTORY
Service Configuration Tables\FACTORY
Service Configuration Tables\FACTORY
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Status Display Tables\FREECOOL
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Configuration Tables\USER
Configuration Tables\USER
Configuration Tables\USER
Status Display Tables\MODES
Configuration Tables\BRODEFS\BROCASTS
Configuration Tables\BRODEFS\BROCASTS
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Configuration Tables\OCCPC01S
Status Display Tables\STATEGEN
Configuration Tables\OCCPC01S
Service Configuration Tables\MAINTCFG
Service Configuration Tables\MAINTCFG
Service Configuration Tables\MAINTCFG
Status Display Tables\STATEGEN
Maintenance Display Tables\SERMAINT
Maintenance Display Tables\SERMAINT
Status Display Tables\GENUNIT
Status Display Tables\STATEGEN
Configuration Tables\USER
Status Display Tables\GENUNIT
Configuration Tables\OCCPC01S
TOUCH PILOT PATH
CCN TABLE NAME
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
124
Pinch offset circuit A
Pinch offset circuit B
Pinch offset circuit C
Power Down 1: day-mon-year
Power Down 1: hour-minute
Power Down 2: day-mon-year
Power Down 2: hour-minute
Power Down 3: day-mon-year
Power Down 3: hour-minute
Power Down 4: day-mon-year
Power Down 4: hour-minute
Power Down 5: day-mon-year
Power Down 5: hour-minute
Power Frequency 60HZ Sel
Power On 1: day-mon-year
Power On 1: hour-minute
Power On 2: day-mon-year
Power On 2: hour-minute
Power On 3: day-mon-year
Power On 3: hour-minute
Power On 4: day-mon-year
Power On 4: hour-minute
Power On 5: day-mon-year
Power On 5: hour-minute
Power Supply Voltage
Prev unoccupied Day
Prev unoccupied Day
Prev unoccupied Time
Prev unoccupied Time
Prop PID Gain Varifan
Pump Auto Rotation Delay
Pump Periodic Start
Pump Sticking Protection
Pumpdown Pressure Cir A
Pumpdown Pressure Cir B
Pumpdown Saturated Tmp A
Pumpdown Saturated Tmp B
Quick EHS for Defrost
Quick Test Enable
Quick Test Enable
Ramp Loading Active
Ramp Loading Select
Ready or Running Status
Realarm Time
Recl Valve Max Position
Recl Valve Min Position
Reclaim Active
Reclaim Condenser Flow
Reclaim Condenser Heater
Reclaim Condenser Pump
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
p_ofst_a
p_ofst_b
p_ofst_c
date_of1
time_of1
date_of2
time_of2
date_of3
time_of3
date_of4
time_of4
date_of5
time_of5
freq_60H
date_on1
time_on1
date_on2
time_on2
date_on3
time_on3
date_on4
time_on4
date_on5
time_on5
voltage
PRVUNDAY
PRVUNDAY
PRVUNTIM
PRVUNTIM
hd_pg
pump_del
Mode_08
pump_per
PD_P_A
PD_P_B
hr_sat_a
hr_sat_b
ehs_defr
Q_TSTRQ
Q_TSTRQ
Mode_05
ramp_sel
READY
RE_ALARM
max_3w
min_3w
Mode_14
CONDFLOW
cond_htr
HPUMP_1
TOUCH PILOT PATH
MAIN MENU\Service\SERVICE1
MAIN MENU\Service\SERVICE1
MAIN MENU\Service\SERVICE1
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Service\FACTORY
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Maint\LAST_POR
MAIN MENU\Service\FACTORY
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Service\SERVICE1
MAIN MENU\Config\USER
MAIN MENU\Status\MODES
MAIN MENU\Config\USER
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Config\USER
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\MODES
MAIN MENU\Config\USER
MAIN MENU\Status\STATEGEN
MAIN MENU\Config\ALARMDEF
MAIN MENU\Service\SERVICE1
MAIN MENU\Service\SERVICE1
MAIN MENU\Status\MODES
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
LINE
12
13
14
3
4
7
8
11
12
15
16
19
20
3
1
2
5
6
9
10
13
14
17
18
4
11
11
12
12
6
14
9
15
11
21
13
23
37
1
1
6
5
30
4
20
19
15
3
4
2
READ/
WRITE
RW
RW
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RW
RO
RO
RO
RO
RW
RW
RO
RW
RO
RO
RO
RO
RW
RW
RW
RO
RW
RO
RW
RW
RW
RO
RO
RO
RO
CCN TABLE NAME
Service Configuration Tables\SERVICE1
Service Configuration Tables\SERVICE1
Service Configuration Tables\SERVICE1
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Service Configuration Tables\FACTORY
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Maintenance Display Tables\LAST_POR
Service Configuration Tables\FACTORY
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Service Configuration Tables\SERVICE1
Configuration Tables\USER
Status Display Tables\MODES
Configuration Tables\USER
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Configuration Tables\USER
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST2
Status Display Tables\MODES
Configuration Tables\USER
Status Display Tables\STATEGEN
Configuration Tables\ALARMDEF\ALARMS01
Service Configuration Tables\SERVICE1
Service Configuration Tables\SERVICE1
Status Display Tables\MODES
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
125
Reclaim Deadband
Reclaim Entering Fluid
Reclaim Fluid Setpoint
Reclaim Leaving Fluid
Reclaim NRCP2 Board
Reclaim Setpoint
Reclaim Status Circuit A
Reclaim Status Circuit B
Reclaim Valve Position
Reference Number
Refrigerant Charge Ctrl
Remote Heat/Cool Switch
Remote Interlock Status
Remote Reclaim Switch
Remote Setpoint Switch
Requested Electric Stage
Reset Amount
Reset in Effect
Reset Maintenance Alert
Reset/Setpnt 4-20mA Sgnl
Reverse Alarms Relay
Rotate Condenser Pumps?
Rotate Cooler Pumps?
Run Status
Running Status
Reference Delta
Circuit A
Circuit B
Refrigerant Pump Out
Circuit A
Circuit B
Circuit C
Running Output
Circuit A
Circuit B
Circuit C
Saturated Condensing Tmp
Circuit A
Circuit B
Circuit C
Saturated Suction Temp
Circuit A
Circuit B
Circuit C
LEGEND
RO — Read Only
RW — Read/Write
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Service\MAINTCFG
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Maint\LOADFACT
MAIN MENU\Maint\LOADFACT
MAIN MENU\Status\MODES
MAIN MENU\Maint\SERMAINT
MAIN MENU\Status\STATEGEN
MAIN MENU\Config\USER
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\STATEGEN
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\STATEGEN
37
5
7
6
10
36
10
20
8
6
3
3
15
5
7
23
6
4
1
41
43
25
22
4
31
READ/
WRITE
RW
RO
RO
RO
RO
RW
RO
RO
RO
RO
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RW
RO
RO
RO
RO
delt_r_a
delt_r_b
MAIN MENU\Maint\DEFROSTM
MAIN MENU\Maint\DEFROSTM
12
29
RO
RO
Maintenance Display Tables\DEFROSTM
Maintenance Display Tables\DEFROSTM
FC_PMP_A
FC_PMP_B
FC_PMP_C
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
MAIN MENU\Status\FREECOOL
16
26
36
RO
RO
RO
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Status Display Tables\FREECOOL
Q_RUN_A
Q_RUN_B
Q_RUN_C
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
43
44
45
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
SCT_A
SCT_B
SCT_C
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
12
12
12
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
SST_A
SST_B
SST_C
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
13
13
13
RO
RO
RO
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
TOUCH PILOT
POINT NAME
hr_deadb
HR_EWT
RSP
HR_LWT
REC_NRCP
rsp
hrstat_a
hrstat_b
hr_v_pos
RefNum
charge_c
HC_SW
REM_LOCK
RECL_SW
SETP_SW
eh_stage
reset
Mode_03
S_RESET
SP_RESET
al_rever
ROTHPUMP
ROTCPUMP
STATUS
RUNNING
TOUCH PILOT PATH
LINE
CCN TABLE NAME
Setpoint Configuration Tables\SETPOINT
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Maintenance Display Tables\BOARD_PN
Setpoint Configuration Tables\SETPOINT
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Configuration Tables\!CtlrID\PD5_XAXQ
Service Configuration Tables\MAINTCFG
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Maintenance Display Tables\LOADFACT
Maintenance Display Tables\LOADFACT
Status Display Tables\MODES
Maintenance Display Tables\SERMAINT
Status Display Tables\STATEGEN
Configuration Tables\USER
Status Display Tables\STATEGEN
Status Display Tables\STATEGEN
Status Display Tables\GENUNIT
Status Display Tables\STATEGEN
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
126
SCT Candidate
Circuit A
Circuit B
Circuit C
SCT Control Point
Circuit A
Circuit B
Circuit C
Slide Valve 1
Circuit A
Circuit B
Circuit C
Slide Valve 2
Circuit A
Circuit B
Circuit C
Slide Valve 1 Output
Circuit A
Circuit B
Circuit C
Slide Valve 2 Output
Circuit A
Circuit B
Circuit C
Suction Pressure
Circuit A
Circuit B
Circuit C
S1 Config Switch (8 ->1)
S1 Config Switch (8 ->1)
S1 Config Switch (8 ->1)
Second Setpoint in Use
Serial Number
Service Test Enable
Servicing Alert
Setpoint Control
Setpoint Occupied?
Setpoint select
Shutdown Indicator State
Slave Address
Slave Chiller State
Slave Chiller Total Cap
Slave lagstat
Slide Valve Capacity A
Slide Valve Capacity B
Slide Valve Capacity C
Soft Starter Select
Software Part Number
Space T Full Reset Value
Space T No Reset Value
Staged Loading Sequence
Start if Error Higher
Startup Delay in Effect
Stop Pump During Standby
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
TOUCH PILOT PATH
LINE
READ/
WRITE
CCN TABLE NAME
sct_fu_a
sct_fu_b
sct_fu_c
MAIN MENU\Maint\FANCTRL
MAIN MENU\Maint\FANCTRL
MAIN MENU\Maint\FANCTRL
2
6
10
RO
RO
RO
Maintenance Display Tables\FANCTRL
Maintenance Display Tables\FANCTRL
Maintenance Display Tables\FANCTRL
sct_sp_a
sct_sp_b
sct_sp_c
MAIN MENU\Maint\FANCTRL
MAIN MENU\Maint\FANCTRL
MAIN MENU\Maint\FANCTRL
1
5
9
RO
RO
RO
Maintenance Display Tables\FANCTRL
Maintenance Display Tables\FANCTRL
Maintenance Display Tables\FANCTRL
Q_SLI_1A
Q_SLI_1B
Q_SLI_1C
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
17
24
31
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Q_SLI_2A
Q_SLI_2B
Q_SLI_2C
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
18
25
32
RW
RW
RW
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
SLID_1_A
SLID_1_B
SLID_1_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
3
3
3
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
SLID_2_A
SLID_2_B
SLID_2_C
MAIN MENU\Status\CIRCA_D
MAIN MENU\Status\CIRCB_D
MAIN MENU\Status\CIRCC_D
4
4
4
RO
RO
RO
Status Display Tables\CIRCA_D
Status Display Tables\CIRCB_D
Status Display Tables\CIRCC_D
SP_A
SP_B
SP_C
cpa_s1_m
cpb_s1_m
cpc_s1_m
Mode_02
SerialNo
Q_STREQ
s_alert
sp_ctrl
SP_OCC
sp_sel
SHUTDOWN
slv_addr
slv_stat
slv_capt
lagstat
Q_SLIA
Q_SLIB
Q_SLIC
softstar
PartNum
spacr_fu
spacr_no
seq_typ
start_dt
Mode_01
pump_sby
MAIN MENU\Status\CIRCA_AN
MAIN MENU\Status\CIRCB_AN
MAIN MENU\Status\CIRCC_AN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Status\MODES
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Status\SERV_TST
MAIN MENU\Service\MAINTCFG
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\GENUNIT
MAIN MENU\Status\STATEGEN
MAIN MENU\Config\MST_SLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Status\SERV_TST
MAIN MENU\Status\SERV_TST
MAIN MENU\Status\SERV_TST
MAIN MENU\Service\FACTORY
MAIN MENU\Config\Ctlr-ID
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Config\USER
MAIN MENU\Config\MST_SLV
MAIN MENU\Status\MODES
MAIN MENU\Config\USER
4
4
4
13
17
21
3
5
1
2
27
26
25
27
11
6
7
14
4
6
8
8
3
12
11
4
19
2
16
RO
RO
RO
RO
RO
RO
RO
RO
RW
RW
RO
RO
RW
RO
RW
RO
RO
RO
RW
RW
RW
RW
RO
RW
RW
RW
RW
RO
RW
Status Display Tables\CIRCA_AN
Status Display Tables\CIRCB_AN
Status Display Tables\CIRCC_AN
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Status Display Tables\MODES
Configuration Tables\!CtlrID\PD5_XAXQ
Status Display Tables\SERV_TST
Service Configuration Tables\MAINTCFG
Status Display Tables\GENUNIT
Status Display Tables\GENUNIT
Status Display Tables\GENUNIT
Status Display Tables\STATEGEN
Configuration Tables\MST_SLV
Maintenance Display Tables\MSTSLAVE
Maintenance Display Tables\MSTSLAVE
Maintenance Display Tables\MSTSLAVE
Status Display Tables\SERV_TST
Status Display Tables\SERV_TST
Status Display Tables\SERV_TST
Service Configuration Tables\FACTORY
Configuration Tables\!CtlrID\PD5_XAXQ
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Configuration Tables\USER
Configuration Tables\MST_SLV
Status Display Tables\MODES
Configuration Tables\USER
APPENDIX A — TOUCH PILOT™ DISPLAY TABLES (cont)
TOUCH PILOT DESCRIPTION
127
Sub Condenser Temp Cir A
Sub Condenser Temp Cir B
Subcooling Temperature A
Subcooling Temperature B
Suction A Temp Average
Suction B Temp Average
Suction C Temp Average
Suction SH Control Pt A
Suction SH Control Pt B
Suction SH Control Pt C
Suction Superheat A
Suction Superheat B
Suction Superheat C
Switch Limit Setpoint 1
Switch Limit Setpoint 2
Switch Limit Setpoint 3
System Manager Active
TCPM Board Comp A
TCPM Board Comp B
TCPM Board Comp C
Timed Overrider Hours
Timed Overrider Hours
Timed-Override Duration
Timed-Override Duration
Timed-Override in Effect
Timed-Override in Effect
Total Fans NB
Circuit A
Circuit B
Circuit C
Unit Capacity Model
Unit is Master or Slave
Unit Off to On Delay
Unit Type (Heat Pump=2)
Use Password
Valve Actuators Heaters
VLT Fan Drive Select
VLT Fan Drive RPM
Water Cond Enter Valv A
Water Cond Enter Valv B
Water Cond Enter Valve A
Water Cond Enter Valve B
Water Cond Leav Valve B
Water Cond Leaving Valve A
Water Cond Leaving Valve B
Water Delta T
Water Exchanger Pump 1
Water Exchanger Pump 2
Water Filter Ctrl (days)
Water Loop Control
Water Pump #1 Hours
Water Pump #2 Hours
Water Val Condensing Stp
Watre Cond Leav Valve A
Wye Delta Start Select
LEGEND
RO — Read Only
RW — Read/Write
TOUCH PILOT
POINT NAME
hr_subta
hr_subtb
hr_subca
hr_subcb
sst_m_a
sst_m_b
sst_m_c
sh_sp_a
sh_sp_b
sh_sp_c
SH_A
SH_B
SH_C
lim_sp1
lim_sp2
lim_sp3
Mode_10
cpa_vers
cpb_vers
cpc_vers
OVR_EXT
OVR_EXT
OVE_HRS
OVE_HRS
OVERLAST
OVERLAST
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\PR_LIMIT
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Maint\EXV_CTRL
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Status\MODES
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
MAIN MENU\Maint\BOARD_PN
Configuration Tables\OCCPC01S
MAIN MENU\Schedule\OCCPC02S
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
MAIN MENU\Maint\OCCDEFCM\OCC1PO1S
MAIN MENU\Maint\OCCDEFCM\OCC2PO2S
12
22
14
24
4
8
12
5
12
19
4
11
18
33
34
35
11
11
15
19
1
1
4
4
3
3
READ/
WRITE
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RW
RW
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
nb_fan_a
nb_fan_b
nb_fan_c
unitsize
mstslv
off_on_d
unit_typ
use_pass
FC_HTR
vlt_set
vlt_rpm
Q_HREW_A
Q_HREW_B
hr_ew_a
hr_ew_b
Q_HRLW_B
hr_lw_a
hr_lw_b
delta_t
Q_PMP1
Q_PMP2
wfilte_c
wloop_c
hr_cpum1
hr_cpum2
w_sct_sp
Q_HRLW_A
wye_delt
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY2
MAIN MENU\Service\FACTORY
MAIN MENU\Maint\M_MSTSLV
MAIN MENU\Config\USER
MAIN MENU\Service\FACTORY
MAIN MENU\Service\SERVICE1
MAIN MENU\Status\FREECOOL
MAIN MENU\Service\FACTORY
MAIN MENU\Service\FACTORY
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\QCK_TST2
MAIN MENU\Status\RECLAIM
MAIN MENU\Status\RECLAIM
MAIN MENU\Maint\LOADFACT
MAIN MENU\Status\QCK_TST1
MAIN MENU\Status\QCK_TST1
MAIN MENU\Service\MAINTCFG
MAIN MENU\Service\MAINTCFG
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Service\UPDTHOUR
MAIN MENU\Setpoint\SETPOINT
MAIN MENU\Status\QCK_TST2
MAIN MENU\Service\FACTORY
14
15
16
2
2
6
1
24
10
22
23
5
9
16
26
10
18
28
4
37
38
9
4
13
14
38
6
9
RW
RW
RW
RW
RO
RW
RW
RW
RO
RW
RW
RW
RW
RO
RO
RW
RO
RO
RO
RW
RW
RW
RW
RW
RW
RW
RW
RW
TOUCH PILOT PATH
LINE
CCN TABLE NAME
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\PR_LIMIT
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Maintenance Display Tables\EXV_CTRL
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Setpoint Configuration Tables\SETPOINT
Status Display Tables\MODES
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Maintenance Display Tables\BOARD_PN
Configuration Tables\OCCPC01S
Configuration Tables\OCCPC02S
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Maintenance Display Tables\OCCDEFCM\OCC1PO1S
Maintenance Display Tables\OCCDEFCM\OCC2PO2S
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY2
Service Configuration Tables\FACTORY
Maintenance Display Tables\MSTSLAVE
Configuration Tables\USER
Service Configuration Tables\FACTORY
Service Configuration Tables\SERVICE1
Status Display Tables\FREECOOL
Service Configuration Tables\FACTORY
Service Configuration Tables\FACTORY
Status Display Tables\QCK_TST2
Status Display Tables\QCK_TST2
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Status Display Tables\QCK_TST2
Status Display Tables\RECLAIM
Status Display Tables\RECLAIM
Maintenance Display Tables\LOADFACT
Status Display Tables\QCK_TST1
Status Display Tables\QCK_TST1
Service Configuration Tables\MAINTCFG
Service Configuration Tables\MAINTCFG
Service Configuration Tables\UPDTHOUR
Service Configuration Tables\UPDTHOUR
Setpoint Configuration Tables\SETPOINT
Status Display Tables\QCK_TST2
Service Configuration Tables\FACTORY
APPENDIX B — NAVIGATOR™ DISPLAY TABLES
MODE — RUN STATUS
ITEM
VIEW
EXPANSION
 EWT
AUTO DISPLAY
Entering Fluid Temp
 LWT
Leaving Fluid Temp
 SETP
Active Setpoint
 CTPT
Control Point
 STAT
Unit Run Status
 OCC
 CTRL
Occupied
Status Unit Control Type
 CAP
 CAP. A
 CAP. B
 CAP. C
 CAP. S
 LIM
 CURR
 CUR.L
 ALRM
Percent Total Capacity
Percent Capacity Cir A
Percent Capacity Cir B
Percent Capacity Cir C
Capacity Indicator
Active Demand Limit Val
Actual Chiller Current
Chiller Current Limit
Alarm State
 EMGY
 CH.SS
 HC.ST
Emergency Stop
CCN Chiller Start Stop
Heat Cool Status
 RC.ST
 TIME
 MNTH
Reclaim Select Status
Time of Day
Month of Year
 DATE
 YEAR
RUN
 HRS.U
 STR.U
 HR.P1
 HR.P2
 HR.P3
HOUR
 HR.A
 HR.B
 HR.C
STRT
 ST.A
 ST.B
 ST.C
Day of Month
Year of Century
MACHINE STARTS/HOURS
Machine Operating Hours
Machine Starts
Water Pump 1 Run Hours
Water Pump 2 Run Hours
Condenser Pump 1 Hours
COMPRESSOR RUN HOURS
Compressor A Run Hours
Compressor B Run Hours
Compressor C Run Hours
COMPRESSOR STARTS
Compressor A Starts
Compressor B Starts
Compressor C Starts
UNITS
XXXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
RANGE
COMMENT
WRITE
STATUS
0-100
CCN TABLE
STATEGEN
CCN POINT
COOL_EWT
0-100
STATEGEN
COOL_LWT
0-100
GENUNIT
SP
0-100
GENUNIT
CTRL_PNT
GENUNIT
STATUS
GENUNIT
GENUNIT
CHIL_OCC
ctr_type
GENUNIT
GENUNIT
GENUNIT
GENUNIT
LOADFACT
GENUNIT
GENUNIT
GENUNIT
GENUNIT
CAP_T
CAPA_T
CAPB_T
CAPC_T
OVER_CAPLC
DEM-LIM
TOT_CURR
CURR_LIM
ALM
GENUNIT
GENUNIT
GENUNIT
EMSTOP
CHILL_S_S
HEATCOOL
GENUNIT
N/A
N/A
reclaim_sel
TIME
moy
XX
XX
Off
Running
Stopping
Delay
NO/YES
Local Off
Local On
CCN
Remote
0-100
0-100
0-100
0-100
0-32
0-100
0-4000
0-4000
0=Normal
1=Partial
2=Shutdown
DSBL/ENBL
DSBL/ENBL
0=Cooling
1=Heating
2=Standby
NO/YES
00:00-23:59
1=January
2=February
3=March
4=April
6=May
6=June
7=July
8=August
9=September
10=October
11=November
12=December
1-31
00-99
N/A
N/A
dom
yoc
XXXX (hours)
XXXX
XXXX (hours)
XXXX (hours)
XXXX (hours)
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
forcible
forcible
forcible
forcible
forcible
STRTHOUR
STRTHOUR
STRTHOUR
STRTHOUR
STRTHOUR
hr_mach
st_mach
hr_cpum1
hr_cpum2
hr_hpump1
XXXX (hours)
XXXX (hours)
XXXX (hours)
0-999999*
0-999999*
0-999999*
forcible
forcible
forcible
STRTHOUR
STRTHOUR
STRTHOUR
hr_cp_a
hr_cp_b
hr_cp_c
XXXX
XXXX
XXXX
0-999999*
0-999999*
0-999999*
forcible
forcible
forcible
STRTHOUR
STRTHOUR
STRTHOUR
st_cp_a
st_cp_b
st_cp_c
XXX (%)
XXX (%)
XXX (%)
XXX (%)
XX
XXX (%)
XXX (amps)
XXX (amps)
XX.XX
*As data in all of these categories can exceed 9999 the following display strategy is used:
From 0-9999 display as 4 digits.
From 9999-99999 display xx.xK
From 99900-999999 display as xxxK.
128
Standby not
supported.
Not supported.
PAGE
NO.
10,48,
69
10,48,
49,69
38,69
38,48,
49,59,
69
25,27,
105
25,27
25,27
47
69
49
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — RUN STATUS (cont)
ITEM
FAN
 FR.A1
 FR.A2
 FR.A3
 FR.A4
 FR.A5
 FR.A6
 FR.A7
 FR.A8
 FR.A9
 F.A10
 FR.B1
 FR.B2
 FR.B3
 FR.B4
 FR.B5
 FR.B6
 FR.B7
 FR.B8
 FR.B9
 F.B10
 FR.C1
 FR.C2
 FR.C3
 FR.C4
 FR.C5
 FR.C6
 FR.C7
 FR.C8
 FR.C9
 F.C10
CP.UN
 A.UN
 B.UN
 C.UN
MAIN
 CHRG
 WATE
 PMP.1
 PMP.2
 PMP.3
 PMP.4
 W.FIL
 A.FIL
 B.FIL
 C.FIL
VERS
 APPL
 MARQ
 NAVI
 EXVA
 EXVB
 EXVC
 AUX1
 AUX2
 AUX3
 AUX4
 AUX5
 AUX6
 CPMA
 CPMB
 CPMC
 EMM
 R.BRD
EXPANSION
FAN RUN HOURS
Fan 1 Run Hours Cir A
Fan 2 Run Hours Cir A
Fan 3 Run Hours Cir A
Fan 4 Run Hours Cir A
Fan 5 Run Hours Cir A
Fan 6 Run Hours Cir A
Fan 7 Run Hours Cir A
Fan 8 Run Hours Cir A
Fan 9 Run Hours Cir A
Fan 10 Run Hours Cir A
Fan 1 Run Hours Cir B
Fan 2 Run Hours Cir B
Fan 3 Run Hours Cir B
Fan 4 Run Hours Cir B
Fan 5 Run Hours Cir B
Fan 6 Run Hours Cir B
Fan 7 Run Hours Cir B
Fan 8 Run Hours Cir B
Fan 9 Run Hours Cir B
Fan 10 Run Hours Cir B
Fan 1 Run Hours Cir C
Fan 2 Run Hours Cir C
Fan 3 Run Hours Cir C
Fan 4 Run Hours Cir C
Fan 5 Run Hours Cir C
Fan 6 Run Hours Cir C
Fan 7 Run Hours Cir C
Fan 8 Run Hours Cir C
Fan 9 Run Hours Cir C
Fan 10 Run Hours Cir C
COMPRESSOR DISABLE
Compressor A Disable
Compressor B Disable
Compressor C Disable
PREDICTIVE MAINTENANCE
Refrigerant Charge
Water Loop Size
Pump 1 (Days)
Pump 2 (Days)
Cond Pump 1 (Days)
Cond Pump 2 (Days)
Water Filter
Comp A OIl Filter (days)
Comp B Oil Filter (days)
Comp C Oil Filter (days)
SOFTWARE VERSIONS
CSA-XXXXXXXXX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
XXXXXX-XX-XX
UNITS
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
XXXX (hours)
RANGE
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
0-999999*
COMMENT
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
(days)
(days)
Not supported.
Not supported.
(days)
Press ENTER
and ESCAPE
simultaneously
to read version
information
*As data in all of these categories can exceed 9999 the following display strategy is used:
From 0-9999 display as 4 digits.
From 9999-99999 display xx.xK
From 99900-999999 display as xxxK.
129
WRITE
STATUS
CCN TABLE
CCN POINT
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
FANHOURS
hr_fana1
hr_fana2
hr_fana3
hr_fana4
hr_fana5
hr_fana6
hr_fana7
hr_fana8
hr_fana9
hrfana10
hr_fanb1
hr_fanb2
hr_fanb3
hr_fanb4
hr_fanb5
hr_fanb6
hr_fanb7
hr_fanb8
hr_fanb9
hrfanb10
hr_fanc1
hr_fanc2
hr_fanc3
hr_fanc4
hr_fanc5
hr_fanc6
hr_fanc7
hr_fanc8
forcible
forcible
forcible
CP_UNABL
CP_UNABL
CP_UNABL
un_cp_a
un_cp_b
un_cp_c
SERMAINT
SERMAINT
SERMAINT
SERMAINT
SERMAINT
SERMAINT
SERMAINT
SERMAINT
SERMAINT
SERMAINT
charge_m
wloop_m
cpump1_m
cpump2_m
hpump1_m
hpump2_m
wfilte_m
ofilta_m
ofiltb_m
ofiltc_m
CntlID
PD5_APPL
STDU
Navigator
EXV_BRDA
EXV_BRDB
EXV_BRDC
AUX_BRD1
AUX_BRD2
AUX_BRD3
AUX_BRD4
AUX_BRD5
AUX_BRD6
SPM_CPA
SPM_CPB
SPM_CPC
EMM_NRCP
REC_NRCP
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
BOARD_PN
PAGE
NO.
19
19
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — SERVICE TEST
ITEM
TEST
 T.REQ
EXPANSION
UNITS
MANUAL TEST MODE
Manual Sequence
RANGE
Remote-OffEnable Switch
must be set to
OFF Position
OFF/ON
 CP.A
Compressor A Output
OFF/ON
 SLI.A
Slide Valve Capacity A
 CP.B
 SLI.B
Compressor B Output
Slide Valve Capacity B
 CP.C
 SLI.C
Compressor C Output
Slide Valve Capacity C
unchanged
increase
decrease
OFF/ON
unchanged
increase
decrease
OFF/ON
unchanged
increase
decrease
QUIC
QUICK TEST MODE
 Q.REQ
 EXV.A
 EXV.B
 EXV.C
 ECO.A
 ECO.B
 ECO.C
 FAN.A
 FAN.B
 FAN.C
 SPD.A
 SPD.B
 SPD.C
 HT.A
 SL1.A
 SL2.A
 HGP.A
 OLS.A
 DGT.A
 HT.B
 SL1.B
 SL2.B
 HGP.B
 OLS.B
 DGT.B
 HT.C
 SL1.C
 SL2.C
 HGP.C
 OLS.C
 DGT.C
 PMP.1
 PMP.2
 PMP.3
 CL.HT
 BVL.A
 BVL.B
 BVL.C
 Q.RDY
 Q.RUN
 SHUT
 CATO
 ALRM
 ALRT
Remote-OffEnable Switch
must be set to
ENABLE
Position
OFF/ON
Circuit A EXV % Open
Circuit B EXV % Open
Circuit C EXV % Open
Circ A ECO EXV %
Circ B ECO EXV %
Circ C ECO EXV %
Circuit A Fan Stages
Circuit B Fan Stages
Circuit C Fan Stages
Cir A Varifan position
Cir B Varifan position
Cir C Varifan position
Oil Heater Circuit A
Slide Valve 1 Cir A
Slide Valve 2 Cir B
Hot Gas Bypass A Output
Oil Solenoid Cir A
DGT Cool Solenoid A
Oil Heater Circuit B
Slide Valve 1 Cir B
Slide Valve 2 Cir B
Hot Gas Bypass B Output
Oil Solenoid Cir A
DGT Cool Solenoid B
Oil Heater Circuit C
Slide Valve 1 Cir C
Slide Valve 2 Cir C
Hot Gas Bypass C Output
Oil Solenoid Cir C
DGT Cool Solenoid C
Water Exchanger Pump 1
Water Exchanger Pump 2
Condenser Pump 1
Cooler Heater Output
Ball Valve Position A
Ball Valve Position B
Ball Valve Position C
Chiller Ready Status
Chiller Running Status
Customer Shutdown Stat
Chiller Capacity in 0-10v
Alarm Relay
Alert Relay
XXX (%)
XXX (%)
XXX (%)
XXX (%)
XXX (%)
XXX (%)
X
X
X
XXX (%)
XXX (%)
XXX (%)
XX.X (vdc)
COMMENT
0-100
0-100
0-100
0-100
0-100
0-100
0-8
0-8
0-8
0-100
0-100
0-100
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OPEN/CLSE
OPEN/CLSE
OPEN/CLSE
OFF/ON
OFF/ON
OFF/ON
0-10
OFF/ON
OFF/ON
130
Remote-OffEnable Switch
must be set to
OFF Position
WRITE
STATUS
forcible
CCN TABLE
CCN POINT
SERV_TST
SERV_TST
Q_STREQ
PAGE
NO.
77,
104,
105
forcible
SERV_TST
forcible
SERV_TST
Q_SLIA
forcible
forcible
SERV_TST
SERV_TST
Q_CPB
Q_SLIB
77,78
forcible
forcible
SERV_TST
SERV_TST
Q_CPC
Q_SLIC
77,78
forcible
QCK_TST1
QCK_TST1
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
QCK_TST1
Q_CPA
Q_TSTRQ
Q_EXVA
Q_EXVB
Q_EXVC
Q_ECO_A
Q_ECO_B
Q_ECO_C
Q_FAN_A
Q_FAN_B
Q_FAN_C
Q_VFANA
Q_VFANB
Q_VFANC
Q_HT_A
Q_SLI_1A
Q_SLI_2A
Q_HGBP_A
Q_OILS_A
Q_CDGT_A
Q_HT_B
Q_SLI_1B
Q_SLI_2B
Q_HGBP_B
Q_OILS_B
Q_CDGT_B
Q_HT_C
Q_SLI_1C
Q_SLI_2C
Q_HGBP_C
Q_OILS_C
Q_CDGT_C
Q_PMP1
Q_PMP2
Q_HPMP1
Q_CL_HT
Q_BVL_A
Q_BVL_B
Q_BVL_C
Q_READY
Q_RUN
Q_SHUT
Q_CATO
Q_ALARM
Q_ALERT
77,78
104,
106
76,77
76,77
76,77
77
77
77
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — TEMPERATURE
ITEM
UNIT
 CEWT
EXPANSION
UNIT TEMPERATURES
Cooler Entering Fluid
 CLWT
Cooler Leaving Fluid
 CD.LT
Condenser Entering Fluid
 CD.ET
Condenser Leaving Fluid
 OAT
Outside Air Temperature
 CHWS
Lead/Lag Leaving Fluid
 SPT
Optional Space Temp
 THHR
Cooler Heater Temp
 THR.C
Cooler Heat Temp Cir C
CIR.A
 SCT.A
CIRCUIT A TEMPERATURES
Sat Cond Temp Circ A
 SST.A
Sat Suction Temp Circ A
 DGT.A
Discharge Gas Temp Cir A
 SGT.A
Suction Gas Temp Circ A
 SUP.A
 ECT.A
Superheat Temp Circ A
Economizer Gas Temp A
 ESH.A
Economizer Superheat A
 CTP.A
Motor Temperature Cir A
CIR.B
 SCT.B
CIRCUIT B TEMPERATURES
Sat Cond Temp Circ B
 SST.B
Sat Suction Temp Circ B
 DGT.B
Discharge Gas Temp Cir B
 SGT.B
Suction Gas Temp Circ B
 SUP.B
 ECT.B
Superheat Temp Circ B
Economizer Gas Temp B
 ESH.B
Economizer Superheat B
 CTP.B
Motor Temperature Cir B
 SCT.C
CIR.C
CIRCUIT C TEMPERATURES
Sat Cond Temp Circ C
 SST.C
Sat Suction Temp Circ C
 DGT.C
Discharge Gas Temp Cir C
 SGT.C
Suction Gas Temp Circ C
 SUP.C
 ECT.C
Superheat Temp Circ C
Economizer Gas Temp C
 ESH.C
Economizer Superheat C
 CTP.C
Motor Temperature Cir C
UNITS
RANGE
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X (F/C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X (F/C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X (F/C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–40-245 F
(–40-118 C)
–45-245 F
(–43-118 C)
–45-245 F
(–43-118 C)
–40-245 F
(–40-118 C)
–45-245 F
(–43-118 C)
–45-245 F
(–43-118 C)
–40-245 F
(–40-118 C)
–45-245 F
(–43-118 C)
131
COMMENT
WRITE
STATUS
CCN TABLE
CCN POINT
STATEGEN
COOL_EWT
STATEGEN
COOL_LWT
Not supported.
PAGE
NO.
COND_LWT
Not supported.
COND_EWT
GENUNIT
OAT
10,69
STATEGEN
CHWS
10
STATEGEN
SPACETMP
18
Not supported.
TH_HEATER
Not supported.
T_HEAT_C
CIRCA_AN
SCT_A
CIRCA_AN
SST_A
96
CIRCA_AN
DGT_A
12
CIRCA_AN
SUCT_T_A
14
EXV_CTRL
CIRCA_AN
SH_A
ECO_TP_A
14
EXV_CTRL
eco_sha
CIRCA_AN
CP_TMP_A
CIRCB_AN
SCT_B
12
CIRCB_AN
SST_B
96
CIRCB_AN
DGT_B
12
CIRCB_AN
SUCT_T_B
14
EXV_CTRL
CIRCB_AN
SH_B
ECO_TP_B
14
EXV_CTRL
eco_shb
CIRCB_AN
CP_TMP_B
12
CIRCC_AN
CIRCC_AN
SCT_C
CIRCC_AN
SST_C
96
CIRCC_AN
DGT_C
12
CIRCC_AN
SUCT_T_C
14
EXV_CTRL
CIRCC_AN
SH_C
ECO_TP_C
14
EXV_CTRL
eco_shc
CIRCC_AN
CP_TMP_C
12
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — PRESSURE
ITEM
PRC.A
 DP.A
EXPANSION
CIRCUIT A PRESSURES
Discharge Pressure Cir A
 SP.A
Suction Pressure Circ A
 OP.A
Oil Pressure Circ A
 DOP.A
Oil Pressure Diff A
 ECP.A
Economizer Pressure A
PRC.B
 DP.B
CIRCUIT B PRESSURES
Discharge Pressure Cir B
 SP.B
Suction Pressure Circ B
 OP.B
Oil Pressure Circ B
 DOP.B
Oil Pressure Diff B
 ECP.B
Economizer Pressure B
PRC.C
 DP.C
CIRCUIT A PRESSURES
Discharge Pressure Cir C
 SP.C
Suction Pressure Circ C
 OP.C
Oil Pressure Circ C
 DOP.C
Oil Pressure Diff C
 ECP.C
Economizer Pressure C
UNITS
RANGE
COMMENT
WRITE
STATUS
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
CCN TABLE
CIRCA_AN
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
XXX.X
(psig/kPa)
CCN POINT
PAGE
NO.
DP_A
10,70
CIRCA_AN
SP_A
10
CIRCA_AN
OP_A
12
CIRCA_AN
DOP_A
CIRCA_AN
ECON_P_A
12
CIRCB_AN
DP_B
10,70
CIRCB_AN
SP_B
10
CIRCB_AN
OP_B
12
CIRCB_AN
DOP_B
CIRCB_AN
ECON_P_B
12
CIRCC_AN
DP_C
17,70
CIRCC_AN
SP_C
17
CIRCC_AN
OP_C
12
CIRCC_AN
DOP_C
CIRCC_AN
ECON_P_C
12
MODE — INPUTS
ITEM
GEN.I
 ONOF
 LOCK
 COND
 DLS1
 DLS2
 ICE.D
 DUAL
 ELEC
 PUMP
 OCCS
 HC.SW
 RLOC
 OIL.A
 OIL.B
 OIL.C
 CUR.A
 CUR.B
 CUR.C
 DMND
 RSET
 HT.SW
EXPANSION
GENERAL INPUTS
On Off Switch
Cooler Interlock
Condenser Flow Switch
Demand Limit Switch 1
Demand Limit Switch 2
Ice Done
Dual Setpoint Switch
Electrical Box Safety
Pump Run Feedback
Occupancy Override Swit
Heat Cool Switch Status
Remote Interlock Switch
Oil Level Circuit A
Oil Level Circuit B
Oil Level Circuit C
Motor Current Circuit A
Motor Current Circuit B
Motor Current Circuit C
4-20 mA Demand Signal
4-20 mA Reset/Setpoint
Heater Switch Input
UNITS
XXX.X (amps)
XXX.X (amps)
XXX.X (amps)
XXX.X (mA)
XXX.X (mA)
XXX.X (mA)
RANGE
OPEN/CLSE
OPEN/CLSE
OPEN/CLSE
OPEN/CLSE
OPEN/CLSE
OFF/ON
OFF/ON
OPEN/CLSE
OPEN/CLSE
OFF/ON
OFF/ON
OPEN/CLSE
LOW/HIGH
LOW/HIGH
LOW/HIGH
0-600
0-600
0-600
4 to 20
4 to 20
OFF/ON
132
COMMENT
WRITE
STATUS
CCN TABLE
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
CCN POINT
ONOF
LOCK_1
CONFLOW
LIM_SW1
LIM_SW2
ICE_SW
SETP_SW
ELEC_BOX
PUMP_DEF
OCC_OVSW
HC_SW
REM-LOCK
OIL_L_A
OIL_L_B
OIL_L_C
CURR_A
CURR_B
CURR_C
LIM_ANAL
SP_RESET
HEATR_SW
PAGE
NO.
10
10,48
10
18
18,29
10,29
10
10
18
18
12
12
12
18
18
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — SET POINTS
ITEM
COOL
EXPANSION
UNITS
 CSP.1
COOLING SETPOINTS
Cooling Setpoint 1
 CSP.2
Cooing Setpoint 2
XXXX.X
(deg F/deg C)
 CSP.3
Ice Setpoint
XXXX.X
(deg F/deg C)
 CRV1
Current No Reset Val
XX.X (mA)
 CRV2
Current Full Reset Val
XX.X (mA)
 CRT1
Delta T No Reset Temp
XXX.X (F/C)
 CRT2
Delta T Full Reset Temp
XXX.X (F/C)
 CRO1
OAT No Reset Temp
XXX.X
(deg F/deg C)
 CRO2
OAT Full Reset Temp
XXX.X
(deg F/deg C)
 CRS1
Space T No Reset Temp
XXX.X
(deg F/deg C)
 CRS2
Space T Full Reset Temp
XXX.X
(deg F/deg C)
 DGRC
Degrees Cool Reset
XX.X (F/C)
 CAUT
Cool Changeover Setpt
 CRMP
Cool Ramp Loading
XX.X
(deg F/deg C)
X.X
 HSP.1
HEAT
HEATING SETPOINTS
Heating Setpoint 1
 HSP.2
Heating Setpoint 2
 HRV1
 HRV2
 HRT1
 HRT2
 HRO1
Current to Reset Val
Current Full Reset Val
Delta T No Reset Temp
Delta T Full Reset Temp
OAT No Reset Temp
 HRO2
OAT Full Reset Temp
 DGRH
 HAUT
Degrees Heat Reset
Heat Changeover Setpt
 HRMP
XXXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XX.X (mA)
XX.X (mA)
XXX.X (F/C)
XXX.X (F/C)
XXX.X
(deg F/deg C)
XXX.X
(deg F/deg C)
XX.X (F/C)
XX.X
(deg F/deg C)
X.X
MISC
 DLS1
Heat Ramp Loading
MISC SETPOINTS
Switch Limit Setpoint 1
 DLS2
Switch Limit Setpoint 2
XXX (%)
 DLS3
Switch Limit Setpoint 3
XXX (%)
 W.SCT
Water Val Cond Stp
XXX.X
(deg F/deg C)
XXX (%)
RANGE
–20-70 F
(–29-21 C),
Default = 44.0
–20-70 F
(–29-21 C),
Default = 44.0
–20-70 F
(–29-21 C),
Default = 44.0
0-20,
Default = 0
0-20,
Default = 0
0-125 F
(0-69.4 C),
Default = 0
0-125 F
(0-69.4 C),
Default = 0
0-125 F
(–18-52 C),
Default = 14.0
0-25 F
(–18-52 C),
Default = 14.0
0-125 F
(–18-52 C),
Default = 14.0
0-125 F
(–18-52 C),
Default = 14.0
–30-30 F
(–16.7-16.7 C),
Default = 0
Default = 75.0
COMMENT
Not supported.
0.2-2.0 F
(0.1-1.1 C),
Default = 1.0
WRITE
STATUS
CCN TABLE
CCN POINT
forcible
SETPOINT
csp1
27-29,
46,59
forcible
SETPOINT
csp2
27-29
46,69
forcible
SETPOINT
ice_sp
forcible
SETPOINT
v_cr_no
forcible
SETPOINT
v_cr_fu
forcible
SETPOINT
dt_cr_no
27,29,
46,69,
70
40,42,
43
40,42,
43
38,40,
41
forcible
SETPOINT
dt_cr_fu
38,40,
41
forcible
SETPOINT
oatcr_no
40,41
forcible
SETPOINT
oatcr_fu
40,41
forcible
SETPOINT
spacr_no
40,42
forcible
SETPOINT
spacr_fu
40,42
forcible
SETPOINT
cr_deg
38, 4043
forcible
SETPOINT
cauto_sp
forcible
SETPOINT
cramp_sp
Default = 100
Not supported.
forcible
SETPOINT
HSP.1
Default = 100
Not supported.
forcible
SETPOINT
HSP.2
Default = 0
Default = 0
Default = 0
Default = 0
Default = 14.0
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
forcible
forcible
forcible
forcible
forcible
SETPOINT
SETPOINT
SETPOINT
SETPOINT
SETPOINT
v_hr_no
v_hr_fu
dt_hr_no
dt_hr_fu
oathr_no
Default = 14.0
Not supported.
forcible
SETPOINT
oathr_fu
Default = 0
Default = 64
Not supported.
Not supported.
forcible
forcible
SETPOINT
SETPOINT
DGRH
hauto_sp
Default = 1.0
Not supported.
forcible
SETPOINT
hramp_sp
0-100,
Default = 100
0-100,
Default = 100
0-100,
Default = 100
80-140 F
(26.7-60 C)
133
38,48,
69
forcible
SETPOINT
lim_sp1
43,44
forcible
SETPOINT
lim_sp2
18,43,
44
forcible
Not supported.
PAGE
NO.
SETPOINT
lim_sp3
SETPOINT
w_sct_sp
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — OUTPUTS
ITEM
CIR.A
 CP.A
 HT.A
 SL1.A
 SL2.A
 OLS.A
 HGB.A
 FAN.A
 SPD.A
 EXV.A
 ECO.A
 DGT.A
CIR.B
 CP.B
 HT.B
 SL1.B
 SL2.B
 OLS.B
 HGB.B
 FAN.B
 SPD.B
 EXV.B
 ECO.B
 DGT.B
CIR.C
 CP.C
 HT.C
 SL1.C
 SL2.C
 OLS.C
 HGB.C
 FAN.C
 SPD.C
 EXV.C
 ECO.C
 DGT.C
GEN.O
 PMP.1
 PMP.2
 PMP.3
 CO.HT
 BVL.A
 BVL.B
 BVL.C
 CN.HT
 REDY
 RUN
 SHUT
 CATO
 ALRM
 ALRT
EXPANSION
CIRCUIT A OUTPUTS
Compressor A Relay
Oil Heater Circuit A
Slide Valve 1 Cir A
Slide Valve 2 Cir A
Oil Solenoid Cir A
Hot Gas Bypass Cir A
Circuit A Fan Stages
Circ A Varifan Position
Circuit A EXV % Open
Circ A EXV ECO % Open
DGT Cool Solenoid A
CIRCUIT B OUTPUTS
Compressor B Relay
Oil Heater Circuit B
Slide Valve 1 Cir B
Slide Valve 2 Cir B
Oil Solenoid Cir B
Hot Gas Bypass Cir B
Circuit B Fan Stages
Circ B Varifan Position
Circuit B EXV % Open
Circ B EXV ECO % Open
DGT Cool Solenoid B
CIRCUIT C OUTPUTS
Compressor C Relay
Oil Heater Circuit C
Slide Valve 1 Cir C
Slide Valve 2 Cir C
Oil Solenoid Cir C
Hot Gas Bypass Cir C
Circuit C Fan Stages
Circ C Varifan Position
Circuit C EXV % Open
Circ C EXV ECO % Open
DGT Cool Solenoid C
GENERAL OUTPUTS
Water Exchanger Pump 1
Water Exchanger Pump 2
Condenser Pump 1
Cooler Heater Output
Ball Valve Position A
Ball Valve Position B
Ball Valve Position C
Condenser Heat Output
Chiller Ready Status
Chiller Running Status
Customer Shutdown Stat
Chiller Capacity 0-10 v
Alarm Relay
Alert Relay
UNITS
X
XXX (%)
XXX (%)
XXX (%)
X
XXX (%)
XXX (%)
XXX (%)
RANGE
COMMENT
WRITE
STATUS
XX.X
CCN POINT
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
0-6
0-100
0-100
0-100
OFF/ON
CIRCA_D
CIRCA_D
CIRCA_D
CIRCA_D
CIRCA_D
CIRCA_D
CIRCA_D
CIRCA_AN
CIRCA_AN
CIRCA_AN
CIRCA_D
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
0-6
0-100
0-100
0-100
OFF/ON
CIRCB_D
CIRCB_D
CIRCB_D
CIRCB_D
CIRCB_D
CIRCB_D
CIRCB_D
CIRCB_AN
CIRCB_AN
CIRCB_AN
CIRCB_D
OFF/ON
OFF/ON
OFF/ON
OFF/ON
0-6
0-100
0-100
0-100
OFF/ON
CIRCC_D
CIRCC_D
CIRCC_D
CIRCC_D
CIRCC_D
CIRCC_D
CIRCC_D
CIRCC_AN
CIRCC_AN
CIRCC_AN
CIRCC_D
CP_C
OIL_HT_C
SLID1_C
SLID2_C
OIL_SL_C
STATEGEN
STATEGEN
STATEGEN
STATEGEN
CIRCA_D
CIRCB_D
CIRCC_D
RECLAIM
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
STATEGEN
CPUMP_1
CPUMP_2
HPUMP_1
COOLHEAT
ref_iso_a
ref_iso_b
ref_iso_c
cond_htr
READY
RUNNING
SHUTDOWN
CAPT_010
ALARM
ALERT
OFF/ON
OFF/ON
X
XXX (%)
XXX (%)
XXX (%)
CCN TABLE
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OPEN/CLOSE
OPEN/CLOSE
OPEN/CLOSE
OFF/ON
OFF/ON
OFF/ON
OFF/ON
0-10
OFF/ON
OFF/ON
134
forcible
forcible
Not supported.
CP_A
OIL_HT_A
SLID1_A
SLID2_A
OIL_SL_A
FAN_ST_A
hd_pos_a
EXV_A
EXV_EC_A
dgt_gascool_a
CP_B
OIL_HT_B
SLID1_B
SLID2_B
OIL_SL_B
FAN_ST_B
hd_pos_b
EXV_B
EXV_EC_B
dgt_gascool_b
FAN_ST_C
hd_pos_c
EXV_C
EXV_EC_C
dgt_gascool_c
PAGE
NO.
12
10,12
12
12
12
19
16
14,76
14
12
12
10,12
12
12
12
19
16
14,76
14
12
12
12
12
12
12
19
16,17
14,76
14
12
19
19
10
10
10
10
18
18
18
10
10
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — CONFIGURATION
ITEM
DISP
EXPANSION
UNITS
 TEST
 METR
 LANG
DISPLAY CONFIGURATION
Test Display LEDs
Metric Display
Language Selection
 TYPE
UNIT
UNIT CONFIGURATION
Unit Type
 TONS
Unit Size
XXX
 VAR.A
Nb Fan on Varifan Cir A
 VAR.B
 VAR.C
RANGE
COMMENT
DEFAULT
CCN
TABLE
CCN
POINT
PAGE NO.
OFF/ON
US/METR
English
Espanol
Francais
Portugues
Translated
OFF
US
English
N/A
display_test 8
DISPCONF DISPUNIT
7
DISPCONF LANGUAGE 8
Air cooled
FACTORY
unit_typ
FACTORY
unitsize
X
1 = Air Cooled
2 = Heat Pump
0 to 1800*
(nominal size)
0-8
FACTORY
varfan_a
Nb Fan on Varifan Cir B
X
0-8
FACTORY
varfan_b
Nb Fan on Varifan Cir C
X
0-8
FACTORY
varfan_c
 VOLT
Power Supply Voltage
XXX (volt)
voltage
60 Hz Frequency
Soft Starter Select
Wye Delta T Start Select
Must Trip Amps Cir A
Read Must Trip Amps A
Must Trip Amps Cir B
Read Must Trip Amps B
Must Trip Amps Cir C
Read Must Trip Amps C
S1 Config Switch Cir A
Read S1 Config Switch A
S1 Config Switch Cir B
Read S1 Config Switch B
S1 Config Switch Cir C
Read S1 Config Switch C
Heat Reclaim Select
DX Cooler Select
EMM Module Installed
Password Enable
Factory Password
Cooler Heater Select†
200, 230, 380,
460, 575
NO/YES
NO/YES
NO/YES
0 to 1500
0 to 1500
0 to 1500
0 to 1500
0 to 1500
0 to 1500
0 to 255
0 to 255
0 to 255
0 to 255
0 to 255
0 to 255
NO/YES
NO/YES
NO/YES
ENBL/DSBL
1 to 0150
0-2
FACTORY
 60HZ
 STAR
 Y.D.
 MTA.A
 R.MT.A
 MTA.B
 R.MT.B
 MTA.C
 R.MT.C
 C.SW.A
 R.CSA
 C.SW.B
 R.CSB
 C.SW.C
 R.CSC
 RECL
 DX.CL
 EMM
 PAS.E
 PASS
 CO.HT
NO
NO
NO
ENBL
0111
1
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
freq_60H
softstar
wye_delt
cpa_mtac
cpa_mtam
cpb_mtac
cpb_mtam
cpc_mtac
cpb_mtam
cpa_s1_c
cpa_s1_m
cpb_s1_c
cpb_s1_m
cpc_s1_c
cpc_s1_m
recl_opt
FACTORY
FACTORY
FACTORY
FACTORY
emm_nrcp
pass_enb
fac_pass
heat_sel
 CON.V
 HGBP
 MCHX
 HI.TI
 H.KIT
 PA.NB
 VLT
 RPM
 H.CON
Condenser Valve Select
Hot Gas Bypass Select
MCHX Exchanger Select
High Tiers Display Select
Hydronic Kit Selection
Cooler Pass Number
VLT Fan Drive Select
VLT Fan Drive RPM
High Condensing Select
NO
NO
NO
**
NO
2
NONE
0
NO
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
FACTORY
cond_val
hgbp_sel
mchx_sel
highdisp
XXX (amps)
XXX (amps)
XXX (amps)
XXX (amps)
XXX (amps)
XXX (amps)
XXX (amps)
XXX (amps)
XXX (amps)
XXX (amps)
XXX (amps)
XXX (amps)
XXX
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
1-3
0: No low ambient 0
temperature head
pressure control
1:low ambient
temperature head
pressure control
0: No low ambient 0
temperature head
pressure control
1: low ambient
temperature head
pressure control
0: No low ambient 0
temperature head
pressure control
1: low ambient
temperature head
pressure control
Nameplate value
YES
Not supported.
Not supported.
0-No Heater,
1-Cooler Heater,
2-Future
Not supported.
Not supported.
Not supported.
NO/YES
*Unit size should be entered as nominal size. For units with DX cooler option,
unit capacity is nominal tonnage i.e., 92 should be 90) and configure DX
cooler equal to yes.
†Must be configured to 1 for the motorized ball valves (ABV) to operate.
**Navigator Display = NO, Touch Pilot Display = YES.
135
100
12,50
12,50
12,50
12
12
12
97
67
32,49
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — CONFIGURATION (cont)
ITEM
SERV
 FLUD
EXPANSION
SERVICE CONFIGURATIONS
Cooler Fluid Type
 CFLU
Condenser Fluid Type
 MOP
EXV MOP Setpoint
 HP.TH
High Pressure Threshold
 SHP.A
Cir A Superheat Setp
 SHP.B
Cir B Superheat Setp
 SHP.C
Cir C Superheat Setp
 HTR
Cooler Heater DT Setp
 EWTO
 AU.SM
 LLWT
Entering Water Control
Auto Start When SM Lost
Brine Minimum Fluid Temp
 LOSP
Brine Freeze Setpoint
 FL.SP
 HD.PG
 HD.DG
 HD.IG
 F.LOA
 AVFA
 AVFB
 AVFC
 EWT.S
 MAXL
 CCNA
 CCNB
 BAUD
Brine Flow Switch Setp
Varifan Proportion Gain
Varifan Derivative Gain
Varifan Integral Gain
Fast Load Select
Fan A Drive Attach
Fan B Drive Attach
Fan C Drive Attach
EWT Probe on Cir A Side
Max Condenser LWT 45DC
OPTIONS CONFIGURATION
CCN Address
CCN Bus Number
CCN Baud Rate
 LOAD
Loading Sequence Select
 LLCS
Lead/Lag Circuit Select
 RL.S
 DELY
 ICE.M
 HPUM
Ramp Load Select
Minutes Off Time
Ice Mode Enable
Condenser Pumps Sequence
 PUMP
Cooler Pumps Sequence
 ROT.P
 PM.PS
 P.SBY
 P.LOC
 LS.ST
 LS.ND
 LS.LT
 RV.AL
 OA.TH
Pump Rotation Delay
Periodic Pump Start
Stop Pump In Standby
Flow Checked if Pmp Off
Night Low Noise Start
Night Low Noise End
Low Noise Capacity Lim
Reverse Alarms Relay
Heat Mode OAT Threshold
 CUR.S
 CUR.F
Current Limit Select
Current Limit at 100%
OPTN
UNITS
RANGE
COMMENT
WATER
BRINE
WATER
WATER
BRINE
XX.X
40-60 F
(deg F/deg C)
(4.4-15.6 C)
XXX.X (psi/kPa) 200-300 psi
(1724-1930 kPa)
XX.X (F/C)
12.6-44.0 F
(1.7-7.8 C)
XX.X (F/C)
12.6-44.0 F
(1.7-7.8 C)
XX.X (F/C)
12.6-44.0 F
(1.7-7.8 C)
XX.X (F/C)
0.5-9 F
(0.3-5.0 C)
NO/YES
NO/YES
XX.X
–20-38 F
(deg F/deg C)
(–28.9-3.3 C)
XX.X
–20-50 F
(deg F/deg C)
(–20-10 C)
0-60
XX.X
–10-10
XX.X
–10-10
XX.X
–10-10
0-4
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
XXX
XXX
XX (Minutes)
XXXX (hours)
XX.XX
XX.XX
XXX (%)
1-239
0-239
2400
4800
9600
19200
38400
Equal
Staged
Automatic
Cir A Leads
Cir B Leads
Cir C Leads
ENBL/DSBL
1 to 15†
ENBL/DSBL
No Pump
1 Pump Only
2 Pumps Auto
PMP 1 Manual
PMP 2 Manual
No Pump
1 Pump Only
2 Pumps Auto
PMP 1 Manual
PMP 2 Manual
24 to 3000
NO-YES
NO-YES
NO-YES
00.00-23.59
00-00-23.59
0-100
NO-YES
XX.X
(deg F/deg C)
XXXX
DEFAULT
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
Not supported.
NO/YES
0 to 5000
* Superheat setpoint for DX cooler unit see table below:
SUPERHEAT SETPOINT FOR DX COOLER
UNIT SIZE
FLUID
CKT.
082-242
262-302
327-352
Water
A
15
10
10
LWT 40 F
B
15
15
10
Brine
A
25
20
20
LWT < 40 F
B
25
25
20
†Do not configure to 0.
136
SERVICE1
WATER
62.0
Not supported.
CCN TABLE
CCN POINT
flui_typ
PAGE NO.
28,30,48,
49,69,70,
97,98
cond_typ
SERVICE1
mop_sp
98
290
SERVICE1
hp_th
49,70
14.4*
SERVICE1
sh_sp_a
98
14.4*
SERVICE1
sh_sp_b
98
14.4
SERVICE1
sh_sp_c
98
2.0
SERVICE1
heatersp
69,80,82
NO
NO
38
SERVICE1
SERVICE1
ewt_opt
auto_sm
27,95
27,99
34
SERVICE1
lowestsp
30,70,80,
82,97,98
1
2.0
0.4
0.2
0
NO
NO
NO
YES
NO
SERVICE1
SERVICE1
SERVICE1
SERVICE1
SERVICE1
flow_sp
hd_pg
hd_dg
hd_ig
fastload
SERVICE1
FACTORY
ewt_cirA
max_clwt
1
0
9600
N/A
N/A
N/A
CCNA
CCNB
BAUD
EQUAL
USER
lead_cir
32
AUTOMATIC
USER
seq_typ
31,32
DSBL
1
DSBL
NO PUMP
USER
USER
USER
ramp_sel
off_on_d
ice_cnfg
hpum_seq
38,69
31,68
29,46
NO PUMP
USER
pump_seq
30,31,59,
70,97,102
48
NO
NO
NO
00.00
00.00
100
NO
5F
USER
USER
USER
USER
USER
USER
USER
USER
USER
pump_del
pump_per
pump_sby
pump_loc
nh_start
nh_end
nh_limit
al_rever
heat_th
31,70
30,31,70
NO
2000
USER
USER
curr_sel
curr_ful
30,31,102
38,70
38,70
38,70
20
43,44
43,44
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — CONFIGURATION (cont)
ITEM
RSET
 CRST
EXPANSION
UNITS
RESET, DEMAND LIMIT, MASTER/SLAVE
Cooling Reset Type
 HRST
Heating Reset Type
 DMDC
Demand Limit Select
 DMMX
 DMZE
 MSSL
mA for 100% Demand Limit
mA for 0% Demand Limit
Master/Slave Select
XX.X (mA)
XX.X (mA)
 SLVA
 LLBL
Slave Address
Lead/Lag Balance Select
XXX
 LLBD
 LLDY
 LL.ER
Lead/Lag Balance Delta
Lead/Lag Delay
Start if Error Higher
 LAG.M
Lag Minimum Running Time
 LAGP
XXX (hours)
XX (minutes)
XX.X
(deg F/deg C)
XXX
(min)
Lag Unit Pump Select
 LPUL
 SERI
Lead Pulldown Time
Chillers in Series
XX (minutes)
RANGE
COMMENT
No Reset
Out Air Temp
Delta T Temp
4-20 mA Input
Space Temp
No Reset
Out Air Temp
Delta T Temp
4-20 mA Input
None
Switch
4-20 mA Input
DEFAULT
CCN TABLE
CCN POINT
PAGE NO.
NO RESET
USER
cr_sel
38,40,42,69
NO RESET
USER
hr_sel
NONE
USER
lim_sel
42,43,44,69
44,45
44,45
32,3437,70,95,
99,100
32,34-37
32,34-37,
68
Disable
Master
Slave
1-236
Always Lead
Lag if Fail
Runtime Sel
40-400
2-30
3-18
0.0
10.0
DISABLE
USER
USER
MST_SLV
lim_mx
lim_ze
ms_sel
2
Always
Lead
MST_SLV
MST_SLV
slv_addr
ll_bal
168
10
4
MST_SLV
MST_SLV
MST_SLV
ll_bal_d
lsrt_tim
start_dt
32,34-37,68
32,34-37,68
32,34-37
0-150
0
MST_SLV
lag_mini
32,34-37
OFF if U stp
ON if U stp
0-60
NO/YES
OFF if U stp
MST_SLV
lag_pump
32,34-37,68
0
NO
MST_SLV
MST_SLV
lead_pul
ll_serie
34-37,67,68
32,34-37
137
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — TIMECLOCK
ITEM
TIME
EXPANSION
UNITS
DATE
 MNTH
TIME OF DAY
Hour and Minute
DAY, DATE
Month
 DOM
 DAY
Day of Month
Day of Week
XX
Year of Century
SCHEDULE 1
Period 1 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 2 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 3 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 4 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 5 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 6 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
XX
 HH.MM
 YEAR
SCH1
 PER.1
 PER.1 OCC.1
 PER.1 UNO.1
 PER.1 MON.1
 PER.1 TUE.1
 PER.1 WED.1
 PER.1 THU.1
 PER.1 FRI.1
 PER.1 SAT.1
 PER.1 SUN.1
 PER.1 HOL.1
 PER.2
 PER.2 OCC.2
 PER.2 UNO.2
 PER.2 MON.2
 PER.2 TUE.2
 PER.2 WED.2
 PER.2 THU.2
 PER.2 FRI.2
 PER.2 SAT.2
 PER.2 SUN.2
 PER.2 HOL.2
 PER.3
 PER.3 OCC.3
 PER.3 UNO.3
 PER.3 MON.3
 PER.3 TUE.3
 PER.3 WED.3
 PER.3 THU.3
 PER.3 FRI.3
 PER.3 SAT.3
 PER.3 SUN.3
 PER.3 HOL.3
 PER.4
 PER.4 OCC.4
 PER.4 UNO.4
 PER.4 MON.4
 PER.4 TUE.4
 PER.4 WED.4
 PER.4 THU.4
 PER.4 FRI.4
 PER.4 SAT.4
 PER.4 SUN.4
 PER.4 HOL.4
 PER.5
 PER.5 OCC.5
 PER.5 UNO.5
 PER.5 MON.5
 PER.5 TUE.5
 PER.5 WED.5
 PER.5 THU.5
 PER.5 FRI.5
 PER.5 SAT.5
 PER.5 SUN.5
 PER.5 HOL.5
 PER.6
 PER.6 OCC.6
 PER.6 UNO.6
 PER.6 MON.6
 PER.6 TUE.6
 PER.6 WED.6
 PER.6 THU.6
 PER.6 FRI.6
 PER.6 SAT.6
 PER.6 SUN.6
 PER.6 HOL.6
XX.XX
RANGE
COMMENT
WRITE
STATUS
CCN TABLE
CCN POINT
PAGE
NO.
00.00-23.59
forcible
N/A
HH.MM
7
1=January
2=February
3=March
4=April
5=May
6=June
7=July
8=August
9=September
10=October
11=November
12=December
1-31
1=Monday
2=Tuesday
3=Wednesday
4=Thursday
5=Friday
6=Saturday
7=Sunday
00-99
forcible
N/A
MNTH
7
forcible
forcible
N/A
N/A
DOM
DAY
7
7
forcible
N/A
YEAR
7
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCCTOD1
UNOCTOD1
DOW1
DOW1
DOW1
DOW1
DOW1
DOW1
DOW1
DOW1
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCCTOD2
UNOCTOD2
DOW2
DOW2
DOW2
DOW2
DOW2
DOW2
DOW2
DOW2
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCCTOD3
UNOCTOD3
DOW3
DOW3
DOW3
DOW3
DOW3
DOW3
DOW3
DOW3
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCCTOD4
UNOCTOD4
DOW4
DOW4
DOW4
DOW4
DOW4
DOW4
DOW4
DOW4
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCCTOD5
UNOCTOD5
DOW5
DOW5
DOW5
DOW5
DOW5
DOW5
DOW5
DOW5
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCC1P01S
OCCTOD6
UNOCTOD6
DOW6
DOW6
DOW6
DOW6
DOW6
DOW6
DOW6
DOW6
138
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — TIMECLOCK (cont)
ITEM
SCH1
 PER.7
 PER.7 OCC.7
 PER.7 UNO.7
 PER.7 MON.7
 PER.7 TUE.7
 PER.7 WED.7
 PER.7 THU.7
 PER.7 FRI.7
 PER.7 SAT.7
 PER.7 SUN.7
 PER.7 HOL.7
 PER.8
 PER.8 OCC.8
 PER.8 UNO.8
 PER.8 MON.8
 PER.8 TUE.8
 PER.8 WED.8
 PER.8 THU.8
 PER.8 FRI.8
 PER.8 SAT.8
 PER.8 SUN.8
 PER.8 HOL.8
SCH2
 PER.1
 PER.1 OCC.1
 PER.1 UNO.1
 PER.1 MON.1
 PER.1 TUE.1
 PER.1 WED.1
 PER.1 THU.1
 PER.1 FRI.1
 PER.1 SAT.1
 PER.1 SUN.1
 PER.1 HOL.1
 PER.2
 PER.2 OCC.2
 PER.2 UNO.2
 PER.2 MON.2
 PER.2 TUE.2
 PER.2 WED.2
 PER.2 THU.2
 PER.2 FRI.2
 PER.2 SAT.2
 PER.2 SUN.2
 PER.2 HOL.2
 PER.3
 PER.3 OCC.3
 PER.3 UNO.3
 PER.3 MON.3
 PER.3 TUE.3
 PER.3 WED.3
 PER.3 THU.3
 PER.3 FRI.3
 PER.3 SAT.3
 PER.3 SUN.3
 PER.3 HOL.3
 PER.4
 PER.4 OCC.4
 PER.4 UNO.4
 PER.4 MON.4
 PER.4 TUE.4
 PER.4 WED.4
 PER.4 THU.4
 PER.4 FRI.4
 PER.4 SAT.4
 PER.4 SUN.4
 PER.4 HOL.4
 PER.5
 PER.5 OCC.5
 PER.5 UNO.5
 PER.5 MON.5
 PER.5 TUE.5
 PER.5 WED.5
 PER.5 THU.5
 PER.5 FRI.5
 PER.5 SAT.5
 PER.5 SUN.5
 PER.5 HOL.5
 PER.6
 PER.6 OCC.6
 PER.6 UNO.6
 PER.6 MON.6
 PER.6 TUE.6
 PER.6 WED.6
 PER.6 THU.6
 PER.6 FRI.6
 PER.6 SAT.6
 PER.6 SUN.6
 PER.6 HOL.6
EXPANSION
SCHEDULE 1
Period 7 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 8 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
SCHEDULE 2
Period 1 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 2 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 3 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 4 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 5 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 6 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
UNITS
RANGE
COMMENT
WRITE
STATUS
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
XX.XX
XX.XX
CCN TABLE
CCN POINT
PAGE
NO.
OCCTOD7
UNOCTOD7
DOW7
DOW7
DOW7
DOW7
DOW7
DOW7
DOW7
DOW7
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
OCCP01S
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCCTOD1
UNOCTOD1
DOW1
DOW1
DOW1
DOW1
DOW1
DOW1
DOW1
DOW1
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCCTOD
UNOCTOD2
DOW2
DOW2
DOW2
DOW2
DOW2
DOW2
DOW2
DOW2
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCCTOD
UNOCTOD3
DOW3
DOW3
DOW3
DOW3
DOW3
DOW3
DOW3
DOW3
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCCTOD4
UNOCTOD4
DOW4
DOW4
DOW4
DOW4
DOW4
DOW4
DOW4
DOW4
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCCTOD5
UNOCTOD5
DOW5
DOW5
DOW5
DOW5
DOW5
DOW5
DOW5
DOW5
26
26
26
26
26
26
26
26
26
26
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCCTOD6
UNOCTOD6
DOW6
DOW6
DOW6
DOW6
DOW6
DOW6
DOW6
DOW6
OCCTOD8
UNOCTOD8
DOW8
DOW8
DOW8
DOW8
DOW8
DOW8
DOW8
DOW8
26
139
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — TIMECLOCK (cont)
ITEM
 PER.7
 PER.7 OCC.7
 PER.7 UNO.7
 PER.7 MON.7
 PER.7 TUE.7
 PER.7 WED.7
 PER.7 THU.7
 PER.7 FRI.7
 PER.7 SAT.7
 PER.7 SUN.7
 PER.7 HOL.7
 PER.8
 PER.8 OCC.8
 PER.8 UNO.8
 PER.8 MON.8
 PER.8 TUE.8
 PER.8 WED.8
 PER.8 THU.8
 PER.8 FRI.8
 PER.8 SAT.8
 PER.8 SUN.8
 PER.8 HOL.8
EXPANSION
 HOL.1
 HOL.1 MON.1
Period 7 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
Period 8 Occ/Unocc Sel
Occupied Time
Unoccupied Time
Monday Select
Tuesday Select
Wednesday Select
Thursday Select
Friday Select
Saturday Select
Sunday Select
Holiday Select
HOLIDAYS*
Holiday 1 Configuration
Holiday Start Month
 HOL.1 DAY.1
 HOL.1 DUR.1
 HOL.1 HOL.2
 HOL.1 MON.2
Holiday Start Day
Holiday Duration in Days
Holiday 2 Configuration
Holiday Start Month
 HOL.2 DAY.2
Holiday Start Day
 HOL.2 DUR.2
Holiday Duration in Days
 HOL.16 HO.16
 HOL.16 MO.16
Holiday 16 Configuration
Holiday Start Month
 HOL.16 DA.16
Holiday Start Day
 HOL.16 DU.16
Holiday Duration in Days
HOLI
MCFG
 AL.SV
 CHRG
 WATE
 PMP.1
 PMP.2
 PMP.3
 PMP.4
 W.FIL
 A.FIL
 B.FIL
 C.FIL
 RS.SV
UNITS
RANGE
COMMENT
WRITE
PAGE
STATUS CCN TABLE CCN POINT NO.
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
XX.XX
XX.XX
00:00-23:59
00:00-23:59
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
XX
XX
SERVICE MAINTENANCE CONFIGURATION
Service Warning Select
Refrigerant Charge
Water Loop Size
Pump 1 (days)
XXXX (days)
Pump 2 (days)
XXXX (days)
Cond Pump 1 (days)
XXXX (days)
Cond Pump 2 (days)
XXXX (days)
Water Filter (days)
XXXX (days)
Comp A Oil Filter (days)
XXXX (days)
Comp B Oil Filter (days)
XXXX (days)
Comp C Oil Filter (days)
XXXX (days)
Servicing Alert Reset
OCCTOD7
UNOCTOD7
DOW7
DOW7
DOW7
DOW7
DOW7
DOW7
DOW7
DOW7
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
OCC2P02S
1=January
2=February
3=March
4=April
5=May
6=June
7=July
8=August
9=September
10=October
11=November
12=December
1 to 31
1 to 99
forcible
HOLDY_01
HOL_MON
26
forcible
forcible
HOLDY_01
HOLDY_01
HOL_DAY
HOL_LEN
See
HOL.1 MON.1
See
HOL.1 DAY.1
See
HOL.1 DUR.1
forcible
HOLDY_02
HOL_MON
26
26
26
26
forcible
HOLDY_02
HOL_DAY
26
forcible
HOLDY_02
HOL_LEN
26
See
HOL.1 MON.1
See
HOL.1 DAY.1
See
HOL.1 DUR.1
forcible
HOLDY_16
forcible
HOLDY_16
forcible
HOLDY_16
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
MAINTCFG
MAINTCFG
MAINTCFG
MAINTCFG
MAINTCFG
MAINTCFG
MAINTCFG
MAINTCFG
MAINTCFG
MAINTCFG
MAINTCFG
SERMAINT
OCCTOD8
UNOCTOD8
DOW8
DOW8
DOW8
DOW8
DOW8
DOW8
DOW8
DOW8
102
NO/YES
NO/YES
NO/YES
0-65,500
0-65,500
0-65,500
0-65,500
0-65,500
0-65,500
0-65,500
0-65,500
0=Default
1=Refrigerant Charge
2=Water loop size
3=Not used
4=Pump 1
5=Pump 2
6=Reclaim Pump (not used)
7=Reclaim Pump (not used)
8=Water Filter
9=Compressor A Oil Filter
10=Compressor B Oil Filter
11=Compressor C Oil Filter
12=Reset All
DEFAULT=NO
DEFAULT=NO
DEFAULT=NO
DEFAULT=0
DEFAULT=0
DEFAULT=0
DEFAULT=0
DEFAULT=0
DEFAULT=0
DEFAULT=0
DEFAULT=0
DEFAULT=0
*Holidays range from 1-16. Item has same structure, with the only difference being the two-number identifier.
140
s_alert
charge_a
wloop_c
pump1_c
pump2_c
hpump1_c
hpump2_c
wfilte_c
ofilta_c
ofiltb_c
ofiltc_c
s_reset
19
19
59
APPENDIX B — NAVIGATOR™ DISPLAY TABLES (cont)
MODE — OPERATING MODE
ITEM
SLCT
EXPANSION*
 OPER
OPERATING CONTROL TYPE
Operating Control Type
 SP.SE
Setpoint Select
 HC.SE
Heat Cool Select
MODE*
 MD01
 MD02
 MD03
 MD04
 MD05
 MD06
UNITS
RANGE
Switch Ctrl
Time Sched
CCN Control
Setpoint Occ
Setpoint1
Setpoint2
4-20mA Setp
Dual Setp Sw
Cooling
Heating
Auto Chgover
Heat Cool Sw
OPERATING MODES
First Active Mode
Second Active Mode
Third Active Mode
Fourth Active Mode
Fifth Active Mode
Sixth Active Mode
COMMENT
WRITE
STATUS
CCN TABLE
CCN POINT
PAGE
NO.
Default = Switch forcible
Ctrl
N/A
N/A
Default =
Setpoint Occ
forcible
GENUNIT
sp_ctrl
25-27,
34-37
46
27-29
Default = Cooling forcible
GENUNIT
HC_SEL
27,29
0-32
0-32
0-32
0-32
0-32
0-32
MODES
MODES
MODES
MODES
MODES
MODES
68
68
68
68
68
68
*Up to six current operating modes will be displayed.
NOTE: See Operating Modes starting on page 68.
MODE — ALARMS
ITEM
R.ALM
ALRM†
H.ALM**
EXPANSION*
RESET ALL CURRENT ALARM
CURRENTLY ACTIVE ALARMS
Current Alarm 1
Current Alarm 2
Current Alarm 3
Current Alarm 4
Current Alarm 5
ALARM HISTORY
Alarm History #1
Alarm History #2
Alarm History #49
Alarm History #50
UNITS
RANGE
NO/YES
*Expanded display will be actual alarm description.
†History of up to five past alarms will be displayed.
**History of fifty past alarms will be displayed.
141
COMMENT
WRITE
STATUS
forcible
CCN TABLE
CCN POINT
N/A
N/A
GENUNIT
GENUNIT
GENUNIT
GENUNIT
GENUNIT
alarm_1
alarm_2
alarm_3
alarm_4
alarm_5
ALRMHIST
ALRMHIST
ALRMHIST
ALRMHIST
alm_history_01
alm_history_02
alm_history_49
alm_history_50
PAGE
NO.
88
APPENDIX C — CCN TABLES
STATUS DISPLAY TABLES
TABLE
CIRCA_AN
CIRCA_D
CIRCB_AN
CIRCB_D
DISPLAY NAME
CIRCUIT A ANALOG VALUES
Percent Total Capacity
Discharge Pressure
Suction Pressure
Economizer Pressure
Oil Pressure
OIl Pressure Difference
Motor Current
Motor Temperature
Discharge Gas Temp
Economizer Gas Temp
Saturated Condensing Tmp
Saturated Suction Temp
Compressor Suction Temp
EXV Position
Head Press Actuator Pos
CIRCUIT A DISCRETE
Compressor Output
Slide Valve 1 Output
Slide Valve 2 Output
Oil Heater Output
Oil Solenoid Output
Oil Level Input
DGT Cooling Solenoid
Hot Gas Bypass Output
FANS OUTPUT
Fan Output DO # 1
Fan Output DO # 2
Fan Output DO # 3
Fan Output DO # 4
Fan Output DO # 5
Fan Output DO # 6
Fan Output DO # 7
Fan Output DO # 8
Fan Staging Number
MISCELLANEOUS
Ball Valve Position*
Ball Valve Closing Out*
Ball Valve Opening Out*
4 Way Refrigerant Valve†
CIRCUIT B ANALOG VALUES
Percent Total Capacity
Discharge Pressure
Suction Pressure
Economizer Pressure
Oil Pressure
Oil Pressure Difference
Motor Current
Motor Temperature
Discharge Gas Temp
Economizer Gas Temp
Saturated Condensing Tmp
Saturated Suction Temp
Compressor Suction Temp
EXV Position
Head Press Actuator Pos
CIRCUIT B DISCRETE
Compressor Output
Slide Valve 1 Output
Slide Valve 2 Output
Oil Heater Output
Oil Solenoid Output
Oil Level Input
DGT Cooling Solenoid
Hot Gas Bypass Output
FANS OUTPUT
Fan Output DO # 1
Fan Output DO # 2
Fan Output DO # 3
Fan Output DO # 4
Fan Output DO # 5
Fan Output DO # 6
Fan Output DO # 7
Fan Output DO # 8
Fan Staging Number
MISCELLANEOUS
Ball Valve Position
Ball Valve Closing Out
Ball Valve Opening Out
4 Way Refrigerant Valve†
RANGE
0 - 100
nnn.n
nnn.n
nnn.n
nnn.n
nnn.n
nnn.n
nnnn
nnnn
nnnn
±nnn.n
±nnn.n
±nnn.n
0 - 100
0 - 100
UNITS
%
psi
psi
psi
psi
psi
AMPS
°F
°F
°F
°F
°F
°F
%
%
POINT NAME
CAPA_T
DP_A
SP_A
ECON_P_A
OP_A
DOP_A
CURREN_A
CP_TMP_A
DGT_A
ECO_TP_A
SCT_A
SST_A
SUCT_T_A
EXV_A
hd_pos_a
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
Low/High
ON/OFF
ON/OFF
COMP_A
SLID_1_A
SLID_2_A
OIL_HT_A
OIL_SL_A
OIL_L_A
GASCOOLA
HGBP_A
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
0-10
fan_a1
fan_a2
fan_a3
fan_a4
fan_a5
fan_a6
fan_a7
fan_a8
FAN_ST_A
OPEN/CLSE
ON/OFF
ON/OFF
ON/OFF
ISO_REFA
ISO_CL_A
ISO_OP_A
RV_A
0 - 100
nnn.n
nnn.n
nnn.n
nnn.n
nnn.n
nnn.n
nnnn
nnnn
nnnn
±nnn.n
±nnn.n
±nnn.n
0-100
0-100
%
psi
psi
psi
psi
psi
AMPS
°F
°F
°F
°F
°F
°F
%
%
CAPB_T
DP_B
SP_B
ECON_P_B
OP_B
DOP_B
CURREN_B
CP_TMP_B
DGT_B
ECO_TP_B
SCT_B
SST_B
SUCT_T_B
EXV_B
hd_pos_b
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
Low/High
ON/OFF
ON/OFF
COMP_B
SLID_1_B
SLID_2_B
OIL_HT_B
OIL_SL_B
OIL_L_B
GASCOOLB
HGBP_B
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
0-10
fan_b1
fan_b2
fan_b3
fan_b4
fan_b5
fan_b6
fan_b7
fan_b8
FAN_ST_B
OPEN/CLSE
ON/OFF
ON/OFF
ON/OFF
ISO_REFB
ISO_CL_B
ISO_OP_B
RV_B
*Not supported for units with DX cooler.
†Not supported.
142
WRITE STATUS
APPENDIX C — CCN TABLES (cont)
STATUS DISPLAY TABLES (cont)
TABLE
CIRCC_AN
CIRCC_D
DISPLAY NAME
CIRCUIT C ANALOG VALUES
Percent Total Capacity
Discharge Pressure
Suction Pressure
Economizer Pressure
Oil Pressure
Oil Pressure Difference
Motor Current
Motor Temperature
Discharge Gas Temp
Economizer Gas Temp
Saturated Condensing Tmp
Saturated Suction Temp
Compressor Suction Temp
EXV Position
Head Press Actuator Pos
CIRCUIT C DISCRETE
Compressor Output
Slide Valve 1 Output
Slide Valve 2 Output
Oil Heater Output
Oil Solenoid Output
Oil Level Input
DGT Cooling Solenoid
Hot Gas Bypass Output
FANS OUTPUT
Fan Output DO # 1
Fan Output DO # 2
Fan Output DO # 3
Fan Output DO # 4
Fan Output DO # 5
Fan Output DO # 6
Fan Output DO # 7
Fan Output DO # 8
Fan Staging Number
MISCELLANEOUS
Ball Valve Position
Ball Valve Closing Out
Ball Valve Opening Out
RANGE
0-100
nnn.n
nnn.n
nnn.n
nnn.n
nnn.n
nnn.n
nnnn
nnnn
nnnn
±nnn.n
±nnn.n
±nnn.n
0-100
0-100
UNITS
%
psi
psi
psi
psi
psi
AMPS
°F
°F
°F
°F
°F
°F
%
%
POINT NAME
CAPC_T
DP_C
SP_C
ECON_P_C
OP_C
DOP_C
CURREN_C
CP_TMP_C
DGT_C
ECO_TP_C
SCT_C
SST_C
SUCT_T_C
EXV_C
hd_pos_c
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
Low/High
ON/OFF
ON/OFF
COMP_C
SLID_1_C
SLID_2_C
OIL_HT_C
OIL_SL_C
OIL_L_C
GASCOOLC
HGBP_C
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
0-10
fan_c1
fan_c2
fan_c3
fan_c4
fan_c5
fan_c6
fan_c7
fan_c8
FAN_ST_C
OPEN/CLSE
ON/OFF
ON/OFF
ISO_REFC
ISO_CL_C
ISO_OP_C
FAN HOURS
Free Cool A Pump Hours
Free Cool B Pump Hours
Circuit A Defrost Number
Circuit B Defrost Number
Circuit A Fan #1 Hours
Circuit A Fan #2 Hours
Circuit A Fan #3 Hours
Circuit A Fan #4 Hours
Circuit A Fan #5 Hours
Circuit A Fan #6 Hours
Circuit A Fan #7 Hours
Circuit A Fan #8 Hours
Circuit A Fan #9 Hours
Circuit A Fan #10 Hours
Circuit B Fan #1 Hours
Circuit B Fan #2 Hours
Circuit B Fan #3 Hours
Circuit B Fan #4 Hours
Circuit B Fan #5 Hours
Circuit B Fan #6 Hours
Circuit B Fan #7 Hours
Circuit B Fan #8 Hours
Circuit B Fan #9 Hours
Circuit B Fan #10 Hours
Circuit C Fan #1 Hours
Circuit C Fan #2 Hours
Circuit C Fan #3 Hours
Circuit C Fan #4 Hours
Circuit C Fan #5 Hours
Circuit C Fan #6 Hours
Circuit C Fan #7 Hours
Circuit C Fan #8 Hours
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
143
hours
hours
—
—
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hr_fem_a
hr_fem_b
ub_def_a
ub_def_b
hr_fana1
hr_fana2
hr_fana3
hr_fana4
hr_fana5
hr_fana6
hr_fana7
hr_fana8
hr_fana9
hrfana10
hr_fanb1
hr_fanb2
hr_fanb3
hr_fanb4
hr_fanb5
hr_fanb6
hr_fanb7
hr_fanb8
hr_fanb9
hrfanb10
hr_fanc1
hr_fanc2
hr_fanc3
hr_fanc4
hr_fanc5
hr_fanc6
hr_fanc7
hr_fanc8
WRITE STATUS
APPENDIX C — CCN TABLES (cont)
STATUS DISPLAY TABLES (cont)
TABLE
GENUNIT
DISPLAY NAME
Operating Type
Control Type
Run Status
CCN Chiller Start/Stop
Chiller Occupied?
Minutes Left for Start
Heat/Cool Status
Heat/Cool Select
Heat Reclaim Select
Free Cooling Selct
Alarm State
Current Alarm 1
Current Alarm 2
Current Alarm 3
Current Alarm 4
Current Alarm 5
Percent Total Capacity
Active Demand Limit Val
Lag Capacity Limit Value
Actual Chiller Current
Chiller Current Limit
Current Setpoint
Setpoint Occupied?
Setpoint Control
MODES
Control Point
Controlled Water Temp
External Temperature
Emergency Stop
Startup Delay in Effect
Second Setpoint in Use
Reset in Effect
Demand Limit Active
Ramp Loading Active
Cooler Heater Active
Cooler Pumps Rotation
Pump Periodic Start
Night Low Noise Active
System Manager Active
Master Slave Active
Auto Changeover Active
Free Cooling Active
Reclaim Active
Electric Heat Active
Heating Low EWT Lockout
Condenser Pumps Rotation
Ice Mode in Effect
Defrost Active On Cir A
Defrost Active On Cir B
Low Suction Circuit A
Low Suction Circuit B
Low Suction Circuit C
High DGT Circuit A
High DGT Circuit B
High DGT Circuit C
High Pres Override Cir A
High Pres Override Cir B
High Pres Override Cir C
Low Superheat Circuit A
Low Superheat Circuit B
Low Superheat Circuit C
RANGE
L-Off-Local Off
(Navigator Display= SW1 Switch=Opened)
L-On-Local On
L-Sched-Local On/Off State based on Time Schedules
CCN-Unit is in CCN Control
Remote-On/Off Based on Remote Contact
(not applied to Navigator Display)
Master-Unit Operation in Lead/Lag and it is a Master
Local
CCN
Remote
0 = Off
1 = Running
2 = Stopping
3 = Delay
4 = Tripout
5 = Ready
6 = Override
7 = Defrost
8 = Run Test
9 = Test
Enable/Disable
Yes/No
0-15
0 = Cool
1 = Heat
2 = Stand-by
3 = Both
0 = Cool
1 = Heat
2 = Auto
Yes/No
Yes/No
0 = Normal
1 = Partial
2 = Shutdown
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnn
nnn
nnn
nnn
nnn
±nnn.n
Yes/No
Setpt 1
Setpt 2
Ice_sp
4-20mA
Auto
±nnn.n
±nnn.n
±nnn.n
Enable/Disable
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
Yes/No
*Not supported.
†The forced value will be used.
144
UNITS
POINT NAME
OPER_TYP
WRITE STATUS
ctr_type
STATUS
min
%
%
%
amps
amps
°F
°F
°F
°F
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
CHIL_S_S
CHIL_OCC
min_left
HEATCOOL
forcible
forcible
HC_SEL
forcible
RECL_SEL
FC_DSBLE
ALM
forcible*
forcible
alarm_1
alarm_2
alarm_3
alarm_4
alarm_5
CAP_T
DEM_LIM
LAG_LIM
TOT_CURR
CURR_LIM
SP
SP_OCC
sp_ctrl
CTRL_PNT
CTRL_WT
OAT
EMSTOP
Mode_01
Mode_02
Mode_03
Mode_04
Mode_05
Mode_06
Mode_07
Mode_08
Mode_09
Mode_10
Mode_11
Mode_12
Mode_13
Mode_14
Mode_15
Mode_16
Mode_17
Mode_18
Mode_19
Mode_20
Mode_21
Mode_22
Mode_23
Mode_24
Mode_25
Mode_26
Mode_27
Mode_28
Mode_29
Mode_30
Mode_31
Mode_32
forcible†
forcible†
forcible
forcible
forcible†
forcible
APPENDIX C — CCN TABLES (cont)
STATUS DISPLAY TABLES (cont)
TABLE
QCK_TST1
DISPLAY NAME
Quick Test Enable
Circuit A EXV Position
Circuit B EXV Position
Circuit C EXV Position
Cir A Economizer EXV Pos
Cir B Economizer EXV Pos
Cir C Economizer EXV Pos
Circuit A Fan Stages
Circuit B Fan Stages
Circuit C Fan Stages
Circuit A Head Press Speed
Circuit B Head Press Speed
Circuit C Head Press Speed
Circuit A Oil Heater
Circuit A Oil Solenoid
Circuit A Slide Valve 1
Circuit A Slide Valve 2
Cir A Heater Ball Valve
Cir A Hot Gas Bypass
Cir A DGT Cool Solenoid
Circuit B Oil Heater
Circuit B Oil Solenoid
Circuit B Slide Valve 1
Circuit B Slide Valve 2
Cir B Heater Ball Valve
Cir B Hot Gas Bypass
Cir B DGT Cool Solenoid
Circuit C Oil Heater
Circuit C Oil Solenoid
Circuit C Slide Valve 1
Circuit C Slide Valve 2
Cir C Heater Ball Valve
Cir C Hot Gas Bypass
Cooler Heater Output
Water Exchanger Pump 1
Water Exchanger Pump 2
Condenser Pump 1
Condenser Pump 2*
Chiller Ready Output
Chiller Running Output
Customer Shutdown Out*
Alarm Relay Output
Alert Relay Output
Cir A Running Output*
Cir B Running Output*
Cir C Running Output*
Chiller Capacity in 0-10v
RANGE
no/Yes
0 - 100
0 - 100
0 - 100
0 - 100
0 - 100
0 - 100
0-10
0-10
0-10
0 - 100
0 - 100
0 - 100
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
0 – 10.0
UNITS
—
%
%
%
%
%
%
—
—
—
%
%
%
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
volt
POINT NAME
Q_TSTRQ
Q_EXVA
Q_EXVB
Q_EXVC
Q_ECO_A
Q_ECO_B
Q_ECO_C
Q_FAN_A
Q_FAN_B
Q_FAN_C
Q_VFANA
Q_VFANB
Q_VFANC
Q_HT_A
Q_OILS_A
Q_SLI_1A
Q_SLI_2A
Q_BVL_A
Q_HGBP_A
Q_CDGT_B
Q_HT_B
Q_OILS_B
Q_SLI_1B
Q_SLI_2B
Q_BVL_B
Q_HGBP_B
Q_CDGT_B
Q_HT_C
Q_OILS_C
Q_SLI_1C
Q_SLI_2C
Q_BVL_C
Q_HGBP_C
Q_CL_HT
Q_PMP1
Q_PMP2
Q_HPMP1
Q_HPMP2
Q_READY
Q_RUN
Q_SHUT
Q_ALARM
Q_ALERT
Q_RUN_A
Q_RUN_B
Q_RUN_C
Q_CATO
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
WRITE STATUS
UNITS
POINT NAME
Q_TSTRQ
Q_HREA_A
Q_HRLA_A
Q_HREW_A
Q_HRLW_A
Q_HREA_B
Q_HRLA_B
Q_HREW_B
Q_HRLW_B
Q_CD_HT
Q_RV_A
Q_RV_B
Q_FC_HTR
Q_FCEXVA
Q_FCEXVB
Q_FCBVL_A
Q_FCBVL_B
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
POINT NAME
Q_STREQ
Q_CPA
Q_SLIA
Q_CPB
Q_SLIB
Q_CPC
Q_SLIC
forcible
forcible
forcible
forcible
forcible
forcible
forcible
*Not supported.
NOTE: Disable quick test: all the quick test parameters shall be reset to 0.
TABLE
QCK_TST2*
DISPLAY NAME
Quick Test Enable
Air Cond Enter Valve A
Air Cond Leaving Valv A
Water Cond Enter Valv A
Water Cond Leav Valve A
Air Cond Enter Valve B
Air Cond Leaving Valv B
Water Cond Enter Valv B
Water Cond Leav Valve B
HR Condenser Heater
4 way Valve Circuit A
4 way Valve Circuit B
Free Cooling Heater
Free Cool A EXV Position
Free Cool B EXV Position
Free Cool A Ball Valve
Free Cool B Ball Valve
RANGE
no/Yes
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
Off/On
On/Off
0 - 100
0 - 100
Off/On
Off/On
—
—
—
—
—
—
—
—
—
—
—
—
—
%
%
—
—
WRITE STATUS
*Not supported.
NOTE: Disable quick test: all the quick test parameters shall be reset to 0.
TABLE
SERV_TST
DISPLAY NAME
Service Test Enable*
Compressor A Output
Slide Valve Capacity A
Compressor B Output
Slide Valve Capacity B
Compressor C Output
Slide Valve Capacity C
RANGE
no/Yes
Off/On
0 - 2†
Off/On
0 - 2†
Off/On
0 - 2†
*Yes = service test function enable.
†0 = capacity frozen (unchanged).
1 = capacity increase.
2 = capacity decrease.
145
UNITS
—
—
—
—
—
—
—
WRITE STATUS
APPENDIX C — CCN TABLES (cont)
STATUS DISPLAY TABLES (cont)
TABLE
FREECOOL*
DISPLAY NAME
GENERAL PARAMETERS
Free Cooling Disable ?
LWT – OAT Delta
Current Cooling Power
Estimated FreeCoo Power
Next Session Allowed In
Cooling/FreeCool Timeout
Free Cool Conditions OK ?
Free Cool Request ?
Valve Actuators Heaters ?
CIRCUIT A
Free Cooling Active
Fan Staging Number
3 Way Valve Position
3 Way Valve Status
Refrigerant Pump Out
Pump Inlet Pressure
Pump Outlet Pressure
Pump Differential Pressure
EXV Position
CIRCUIT B
Free Cooling Active
Fan Staging Number
3 Way Valve Position
3 Way Valve Status
Refrigerant Pump Out
Pump Inlet Pressure
Pump Outlet Pressure
Pump Differential Pressure
EXV Position
CIRCUIT C
Free Cooling Active
Fan Staging Number
3 Way Valve Position
3 Way Valve Status
Refrigerant Pump Out
Pump Inlet Pressure
Pump Outlet Pressure
Pump Differential Pressure
EXV Position
RANGE
UNITS
POINT NAME
Yes/No
±nnn.n
nnn
nnn
nn
nn
Yes/No
Yes/No
On/Off
—
°F
°F
°F
minutes
minutes
—
—
—
FC_DSBLE
fc_delta
cool_pwr
fc_pwr
fc_next
fc_tmout
fc_ready
fc_reqst
FC_HTR
Yes/No
1 to 6
nnn
Opening/Closing/...
On/Off
±nnn
±nnn
±nnn
nnn.n
—
—
%
—
—
kPa
kPa
kPa
%
fc_on_a
FAN_ST_A
fc_vlv_a
FC_VLV_A
fc_pmp_a
fc_inp_a
fc_oup_a
fc_dp_a
EXV_A
Yes/No
1 to 6
nnn
Opening/Closing/...
On/Off
±nnn
±nnn
±nnn
nnn.n
—
—
%
—
—
kPa
kPa
kPa
%
fc_on_b
FAN_ST_B
fc_vlv_b
FC_VLV_B
fc_pmp_b
fc_inp_b
fc_oup_b
fc_dp_b
EXV_B
Yes/No
1 to 6
nnn
Opening/Closing/...
On/Off
±nnn
±nnn
±nnn
nnn.n
—
—
%
—
—
kPa
kPa
kPa
%
fc_on_c
FAN_ST_C
fc_vlv_c
FC_VLV_C
fc_pmp_c
fc_inp_c
fc_oup_c
fc_dp_c
EXV_C
*Not supported.
146
APPENDIX C — CCN TABLES (cont)
STATUS DISPLAY TABLES (cont)
TABLE
RECLAIM*
STATEGEN
STRTHOUR
DISPLAY NAME
Heat Reclaim Select
Reclaim Condenser Pump
Reclaim Condenser Flow
Reclaim Condenser Heater
Reclaim Entering Fluid
Reclaim Leaving Fluid
Reclaim Fluid Setpoint
Reclaim Valve Position
HEAT RECLAIM CIRCUIT A
Reclaim Status Circuit A
Pumpdown Pressure Cir A
Sub Condenser Temp Cir A
Pumpdown Saturated Tmp A
Subcooling Temperature A
Air Cond Entering Valv A
Water Cond Enter Valve A
Air Cond Leaving Valve A
Water Cond Leaving Val A
HEAT RECLAIM CIRCUIT B
Reclaim Status Circuit B
Pumpdown Pressure Cir B
Sub Condenser Temp Cir B
Pumpdown Saturated Tmp B
Subcooling Temperature B
Air Cond Entering Valv B
Water Cond Enter Valve B
Air Cond Leaving Valve B
Water Cond Leaving Val B
UNIT DISCRETE IN
On/Off – Remote Switch
Remote Heat/Cool Switch
Current Control
Remote Reclaim Switch
Free Cooling Disable Switch*
Remote Setpoint Switch
Limit Switch 1 Status
Limit Switch 2 Status
Occupied Override Switch
Ice Done Storage Switch
Cooler Flow Switch
Cooler Pump Run Status
Condenser Flow Status
Remote Interlock Status
Electrical Box Interlock*
UNIT DISCRETE OUT
Cooler Flow Setpoint Out*
Heater Switch
Electrical Heat Stage*
Cooler Pump #1 Command
Cooler Pump #2 Command
Rotate Cooler Pumps ?
Condenser Pump #1 Out*
Condenser Pump #2 Out*
Rotate Condenser Pumps?*
Cooler Heater Command
Shutdown Indicator State
Alarm Relay Status
Alert Relay Status
Ready or Running Status
Running Status
UNIT ANALOG
Cooler Entering Fluid
Cooler Leaving Fluid
Condenser Entering Fluid
Condenser Leaving Fluid
Cooler Heater Temp*
Circuit C Heater Temp*
Optional Space Temp
CHWS Temperature
Reset /Setpnt 4-20mA Sgnl
Limit 4-20mA Signal
Chiller Capacity Signal
Machine Operating Hours
Machine Starts Number
Compressor A Hours
Compressor A Starts
Compressor B Hours
Compressor B Starts
Compressor C Hours
Compressor C Starts
WATER PUMPS
Cooler Pump #1 Hours
Cooler Pump #2 Hours
Condenser Pump #1 Hours*
Condenser Pump #2 Hours*
RANGE
Yes/no
On/Off
On/Off
On/Off
±nnn.n
±nnn.n
±nnn.n
±nnn.n
n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
On/Off
On/Off
On/Off
On/Off
n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
On/Off
On/Off
On/Off
On/Off
UNITS
°F
°F
°F
%
psi
°F
°F
^F
psi
°F
°F
^F
POINT NAME
RECL_SEL
CONDPUMP
CONDFLOW
cond_htr
HR_EWT
HR_LWT
RSP
hr_v_pos
hrstat_b
PD_P_B
hr_subtb
hr_sat_b
hr_subcb
hr_ea_b
hr_ew_b
hr_la_b
hr_lw_b
RECL_SW
FC_SW
SETP_SW
LIM_SW1
LIM_SW2
OCC_OVSW
ICE_SW
FLOW_SW
CPUMPDEF
CONDFLOW
REM_ LOCK
ELEC_BOX
On/Off
On/Off
0-4/Off
On/Off
On/Off
Yes/No
On/Off
On/Off
Yes/No
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
SET_FLOW
HEAT_SW
EHS_STEP
CPUMP_1
CPUMP_2
ROTCPUMP
HPUMP_1
HPUMP_2
ROTHPUMP
COOLHEAT
SHUTDOWN
ALARMOUT
ALERT
READY
RUNNING
ONOFF_SW
HC_SW
on_ctrl
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nn.n
±nn.n
±nn.n
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
°F
°F
°F
°F
°F
°F
°F
°F
ma
ma
volts
hours
nnnnn
nnnnn
nnnnn
nnnnn
hours
hours
hours
hours
147
forcible
hrstat_a
PD_P_A
hr_subta
hr_sat_a
hr_subca
hr_ea_a
hr_ew_a
hr_la_a
hr_lw_a
Open/Clse
Open/Clse
Off, On Cool, On Heat,
On Auto
Open/Clse
Open/Clse
Open/Clse
Open/Clse
Open/Clse
Open/Clse
Open/Clse
Open/Clse
Open/Clse
On/Off
Open/Clse
Open/Clse
*Not supported.
WRITE STATUS
hours
hours
hours
COOL_EWT
COOL_LWT
COND_EWT
COND_LWT
HEATER
T_HEAT_C
SPACETMP
CHWSTEMP
SP_RESET
LIM_ANAL
CAPT_010
HR_MACH
st_mach
HR_CP_A
st_cp_a
HR_CP_B
st_cp_b
HR_CP_C
st_cp_c
hr_cpum1
hr_cpum2
hr_hpum1
hr_hpum2
forcible
forcible
forcible
forcible
forcible
forcible
APPENDIX C — CCN TABLES (cont)
CONFIGURATION TABLES
TABLE
!CtlrID/PD5_XAXQ
DISPLAY NAME
Device Name
Description
Location
Software Part Number
Model Number
Serial Number
Reference Number
CCN Bus Number
CCN Element Number
CCN Baud Rate
ALARMDEF/
ALARMS01
BRODEFS/
BROCASTS
Alarm Routing Control
Alarm Equipment Priority
Comm Failure Retry Time
Realarm Time
Alarm System Name
Activate
OAT Broadcast
Bus #
Element #
HOLIDAY/HOLDY_nn
nn = 01 to 16
OCCDEFCS/
OCCnP0nS
n = 1 or 2
DAYLIGHT SAVING SELECT
ENTERING
Month
Day of week* (1=Monday)
Week Number of Month†
LEAVING
Month
Day of week* (1=Monday)
Week Number of Month†
Holiday Start Month
Start Day
Duration (days)
Timed Override Hours
Period 1 DOW (MTWTFSSH)
Occupied From
Occupied To
Period 2 DOW (MTWTFSSH)
Occupied From
Occupied To
Period 3 DOW (MTWTFSSH)
Occupied From
Occupied To
Period 4 DOW (MTWTFSSH)
Occupied From
Occupied To
Period 5 DOW (MTWTFSSH)
Occupied From
Occupied To
Period 6 DOW (MTWTFSSH)
Occupied From
Occupied To
Period 7 DOW (MTWTFSSH)
Occupied From
Occupied To
Period 8 DOW (MTWTFSSH)
Occupied From
Occupied To
RANGE
8 chars
24 chars
24 chars
16 chars
20 chars
12 chars
24 chars
0-239
1-239
9600
19200
38400
0-11111111
0-7
1-240
1-255
8 chars
0=Unused
1=Broadcast time,
date, holiday flag and
OAT.
2=For Standalone
chiller. Daylight savings
time & holiday determination will be done
without broadcasting
through the bus.
DEFAULT
30XW
PRO-DIALOG 5
30XA XQ XW
UNITS
POINT NAME
DevDesc
0
1
9600
Location
PartNum
ModelNum
SerialNo
RefNum
CCNB
CCNA
BAUD
00000000
4
10
30
PRO_XAXQ
2
ALRM_CNT
EQP_TYP
RETRY_TM
RE_ALARM
ALRM_NAM
ccnbroad
CSA-SR-20C47nnnn
min
min
—
0 to 239
0 to 239
0
0
oatbusnm
oatlocad
Disable/Enable
Disable
dayl_sel
1 to 12
1 to 7
1 to 5
3
7
5
startmon
startdow
startwom
1 to 12
1 to 7
1 to 5
0-12
0-31
0-99
0-4
0/1
00:00-24:00
00:00-24:00
0/1
00:00-24:00
00:00-24:00
0/1
00:00-24:00
00:00-24:00
0/1
00:00-24:00
00:00-24:00
0/1
00:00-24:00
00:00-24:00
0/1
00:00-24:00
00:00-24:00
0/1
00:00-24:00
00:00-24:00
0/1
00:00-24:00
00:00-24:00
10
7
5
0
0
0
0
11111111
00:00
24:00
11111111
00:00
00:00
00000000
00:00
00:00
00000000
00:00
00:00
00000000
00:00
00:00
00000000
00:00
00:00
00000000
00:00
00:00
00000000
00:00
00:00
Stopmon
Stoptdow
stopwom
HOL_MON
HOL_DAY
HOL_LEN
OVR_EXT
DOW1
OCCTOD1
UNOCTOD1
DOW2
OCCTOD2
UNOCTOD2
DOW3
OCCTOD3
UNOCTOD3
DOW4
OCCTOD4
UNOCTOD4
DOW5
OCCTOD5
UNOCTOD5
DOW6
OCCTOD6
UNOCTOD6
DOW7
OCCTOD7
UNOCTOD7
DOW8
OCCTOD8
UNOCTOD8
*Day of week where daylight savings time will occur in the morning (at
2:00 am). Daylight savings time occurs on Sunday (7) morning, 1 hour shall
be added when entering and 1 hour subtracted when leaving.
†Date once selected (from 1) shall occur in the week number entered. 1: If day
of week selected is 7 (Sunday) time change will occur the first Sunday (week
number 1) in the month. 5: If day of week selected is 7 (Sunday) time change
will occur the last Sunday of the month (week number 4 or 5).
NOTE: nnnn is software version.
148
APPENDIX C — CCN TABLES (cont)
CONFIGURATION TABLES (cont)
TABLE
CFG_TABn
(n = 1 to 8)
DISPCONF
MST_SLV
DISPLAY NAME
Display n table number 1
Display n var number 1
Display n table number 2
Display n var number 2
Display n table number 3
Display n var number 3
Display n table number 4
Display n var number 4
Display n table number 5
Display n var number 5
Display n table number 6
Display n var number 6
Display n table number 7
Display n var number 7
Display n table number 8
Display n var number 8
Display n table number 9
Display n var number 9
Metric Display on STDU
Language Selection
MASTER SLAVE CONTROL
Master/Slave Select
Master Control Type
Slave Address
Lead Lag Select
Lead/Lag Balance Delta
Lag Start Timer
Lead Pulldown Time
Start if Error Higher
Lag Minimum Running Time
Lag Unit Pump Control
Chiller in Series
RANGE
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
Yes/No
0=English
1=Espanol
2=Francais
3=Portugues
4=Translated
0=Disable
1=Master
2=Slave
1=Local Control
2=Remote Control
3=CCN Control
1 to 236
0=Always Lead
1=Lag Once
Failed Only
2=Lead/Lag
Runtime Sel
40 to 400
2 to 30
0 to 60
0=Stop if Unit Stops
1=Run if Unit Stops
Yes/No
149
DEFAULT
No
0
POINT NAME
tab_nb_1
var_nb_1
tab_nb_2
var_nb_2
tab_nb_3
var_nb_3
tab_nb_4
var_nb_4
tab_nb_5
var_nb_5
tab_nb_6
var_nb_6
tab_nb_7
var_nb_7
tab_nb_8
var_nb_8
tab_nb_9
var_nb_9
DISPUNIT
LANGUAGE
0
ms_sel
1
ms_ctrl
2
0
slv_addr
lead_sel
168
10
0
4
0
0
No
UNITS
hours
min
min
^F
min
ll_bal_d
lstr_tim
lead_pul
start_dt
lag_mini
lag_pump
II_serie
APPENDIX C — CCN TABLES (cont)
CONFIGURATION TABLES (cont)
TABLE
USER
DISPLAY NAME
Circuit Loading Sequence
Staged Loading Sequence
Ramp Loading Select
Unit Off to On Delay
Condenser Pumps Sequence
Cooler Pumps Sequence
Pump Auto Rotation Delay
Pump Sticking Protection
Stop Pump During Standby
Flow Checked if Pump Off
Auto Changeover Select*
Cooling Reset Select
Heating Reset Select*
Demand Limit Type Select
mA For 100% Demand Limit
mA For 0% Demand Limit
Current Limit Select
Current Limit at 100%
Heating OAT Threshold*
Free Cooling Delta T Th*
Full Load Timeout
HSM Both Command Select
NIGHT CONTROL
Start Hour
End Hour
Capacity Limit
Ice Mode Enable
Reverse Alarms Relay
Cooler pump off in heat
Cond pump off in cool
RANGE
0-3
0=Auto,
1=A Lead
2=B Lead,
3 =C Lead
No/Yes
No/Yes
1-15†
0-4*
0-4
0=No Pump
1=One Pump Only
2=Two Pumps Auto
3=Pump#1 Manual
4=Pump#2 Manual
24-3000
No/Yes
No/Yes
No/Yes
No/Yes
0-4
0-4
0=None
1=OAT,
2=Delta T,
3=4-20mA Control
4=Space Temp
0-2
0=None
1=Switch Control
2=4-20mA Control
0-20
0-20
No/Yes
0 to 2000
-4-32
14.4-27
20-300
No/Yes
DEFAULT
0
10
No
2000
5
18
30
No
00:00-24:00
00:00-24:00
0-100
No/Yes
No/Yes
No/Yes
No/Yes
00:00
00:00
100
No
No
No
No
UNITS
0
No
No
1
0
0
48
No
No
No
No
0
0
min
hours
0
POINT NAME
lead_cir
seq_typ
ramp_sel
off_on_d
hpumpseq
cpumpseq
pump_del
pump_per
pump_sby
pump_loc
auto_sel
cr_sel
hr_sel
lim_sel
ma
ma
amps
°F
°F
min
%
lim_mx
lim_ze
curr_sel
curr_ful
heat_th
free_dt
fc_tmout
both_sel
nh_start
nh_end
nh_limit
ice_cnfg
al_rever
stopheat
stopcool
2. If cooling reset select set point has been selected the set point based on
4-20mA input signal through ComfortLink™ control, then a 4-20 mA reset
function shall be ignored. Configuration 3 (4-20mA Control) and 4 (Space
Temperature) shall require an Energy Management Module.
3. Configuration 2 (4-20mA Control) shall require an Energy Management
Module. Configuration 1 Switch Demand limit provides 3 step demand
limit if an Energy Management Module is present. Otherwise, only one
step is allowed.
4. Reverse Alarms Relay configuration will be deenergized when an alarm
and alert relay is present and will be energized when no alarm is present.
*Not supported.
†Do not configure for 0.
NOTES:
1. Flow checked if pump off needed when a command is sent to the primary
pump to prevent cooler from freezing in winter conditions. Command will
set the cooler flow switch to closed while the controls stop the cooler
pump. The controls may then generate an alarm. If this decision is active,
the cooler flow switch is not checked when the cooler pump is stopped.
150
APPENDIX C — CCN TABLES (cont)
SETPOINT CONFIGURATION TABLES
TABLE
SETPOINT
DISPLAY NAME
COOLING
Cooling Setpoint 1
Cooling Setpoint 2
Cooling Ice Setpoint
OAT No Reset Value
OAT Full Reset Value
Delta T No Reset Value
Delta T Full Reset Value
Current No Reset Value
Current Full Reset Value
Space T No Reset Value
SpaceT Full Reset Value
Cooling Reset Deg. Value
Cooling Ramp Loading
HEATING*
Heating Setpoint 1
Heating Setpoint 2
OAT No Reset Value
OAT Full Reset Value
Delta T No Reset Value
Delta T Full Reset Value
Current No Reset Value
Current Full Reset Value
Heating Reset Deg. Value
Heating Ramp Loading
AUTO CHANGEOVER*
Cool Changeover Setpt
Heat Changeover Setpt
MISCELLANEOUS
Switch Limit Setpoint 1
Switch Limit Setpoint 2
Switch Limit Setpoint 3
Reclaim Setpoint*
Reclaim Deadband*
Water Val Condensing Stp*
RANGE
DEFAULT
UNITS
POINT NAME
–20-70
–20-70
–20-70
14-125
14-125
0-25
0-25
0-20
0-20
14-125
14-125
–30-30
0.2-2.0
44.0
44.0
44.0
14.0
14.0
0.0
0.0
0.0
0.0
14.0
14.0
0.0
1.0
°F
°F
°F
°F
°F
^F
^F
ma
ma
°F
°F
^F
^F
csp1
csp2
ice_sp
oatcr_no
oatcr_fu
dt_cr_no
dt_cr_fu
v_cr_no
v_cr_fu
spacr_no
spacr_fu
cr_deg
cramp_sp
80-140
80-140
14-125
14-125
0-25
0- 25
0-20
0-20
–30-30
0.2-2.0
100.0
100.0
14.0
14.0
0.0
0.0
0.0
0.0
0.0
1.0
°F
°F
°F
°F
^F
^F
ma
ma
^F
^F
hsp1
hsp2
oathr_no
oathr_fu
dt_hr_no
dt_hr_fu
v_hr_no
v_hr_fu
hr_deg
hramp_sp
39-122
32-115
75.0
64.0
°F
°F
cauto_sp
hauto_sp
0-100
0-100
0-100
95-140
5-27
80 to 120
100
100
100
122.0
9.0
86
%
%
%
°F
°F
°F
lim_sp1
lim_sp2
lim_sp3
rsp
hr_deadb
w_sct_sp
*Not supported.
MAINTENANCE DISPLAY TABLES
TABLE
BOARD_PN
CUR_PHASE
DEFROSTM*
DISPLAY NAME
EXV Board Circuit A
EXV Board Circuit B
EXV Board Circuit C
AUX Board #1 Part Number
AUX Board #2 Part Number
AUX Board #3 Part Number
AUX Board #4 Part Number
AUX Board #5 Part Number
EMM NRCP2 Board
Reclaim NRCP2 Board
TCPM Board Comp A
Must Trip Amps
S1 Config Switch (8 to 1)
TCPM Board Comp B
Must Trip Amps
S1 Config Switch (8 to 1)
TCPM Board Comp C
Must Trip Amps
S1 Config Switch (8 to 1)
Current Phase 1 Comp A
Current Phase 2 Comp A
Current Phase 3 Comp A
Current Phase 1 Comp B
Current Phase 2 Comp B
Current Phase 3 Comp B
Current Phase 1 Comp C
Current Phase 2 Comp C
Current Phase 3 Comp C
CIR A DEFROST CONTROL
Exchanger Frost Factor
Next Sequence Allowed in
Defrost Active?
Defrost Temperature
Defrost Duration
Fan Sequence Started ?
Override State
Mean SST Calculation
Delta: OAT - Mean SST
Reference Delta
Delta - Reference Delta
Frost Integrator Gain
Defrost Fan Start Cal A
Defrost Fan Offset Cal A
CIR B DEFROST CONTROL
Exchanger Frost Factor
Next Sequence Allowed in
Defrost Active?
Defrost Temperature
Defrost Duration
Fan Sequence Started?
Override State
Mean SST calculation
Delta: OAT - Mean SST
Reference Delta
Delta - Reference Delta
Frost Integrator Gain
Defrost Fan Start Cal B
Defrost Fan Offset Cal B
RANGE
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
0-600
00000000
nnnn
0-600
00000000
XXXXXXXX
0-600
00000000
0-600
0-600
0-600
0-600
0-600
0-600
0-600
0-600
0-600
0-100
nnn
True/False
±nnn.n
nnn
n
nn
±nnn.n
±nnn.n
±nnn.n
±nnn.n
n.n
0.00
0.00
0-100
nnn
True/False
±nnn.n
nnn
n
nn
±nnn.n
±nnn.n
±nnn.n
±nnn.n
n.n
0.00
0.00
*Not supported.
NOTES: Tables for display only. Forcing shall not be supported on this maintenance screen.
151
UNITS
amps
0
amps
0
amps
0
amps
amps
amps
amps
amps
amps
amps
amps
amps
%
minutes
°F
minutes
°F
^F
^F
°F
psi
psi
%
minutes
°F
minutes
°F
^F
^F
^F
psi
psi
POINT NAME
exv_brda
exv_brdb
exv_brdc
aux_brd1
aux_brd2
aux_brd3
aux_brd4
aux_brd5
emm_nrcp
rec_nrcp
cpa_vers
cpa_mtam
cpa_s1_m
cpb_vers
cpb_mtam
cpb_s1_m
cpc_vers
cpc_mtam
cpc_s1_m
cpa_cur1
cpa_cur2
cpa_cur3
cpb_cur1
cpb_cur2
cpb_cur3
cpc_cur1
cpc_cur2
cpc_cur3
frost_a
def_se_a
mode[19]
DEFRT_A
defr_dua
def_fa_a
over_d_a
sst_dm_a
delt_a
delt_r_a
del_v_a
fr_int_a
def_ca_a
def_of_a
frost_b
def_se_b
mode[20]
DEFRT_B
defr_dub
def_fa_b
over_d_b
sst_dm_b
delt_b
delt_r_b
del_v_b
fr_int_b
def_ca_b
def_of_b
WRITE STATUS
APPENDIX C — CCN TABLES (cont)
MAINTENANCE DISPLAY TABLES (cont)
TABLE
FANCTRL
LAST_POR
LOADFACT
EXV_CTRL
DISPLAY NAME
Cir A SCT Control Point
Cir A SCT Candidate
Cir B SCT Control Point
Cir B SCT Candidate
Cir C SCT Control Point
Cir C SCT Candidate
Circuit A Fan Power Drive
Circuit A Fan Drive Amps
Fan A Drive Attach
Fan B Drive Attach
Fan C Drive Attach
Power On 1: day-mon-year
Power On 1: hour-minute
PowerDown 1:day-mon-year
PowerDown 1:hour-minute
Power On 2: day-mon-year
Power On 2: hour-minute
PowerDown 2:day-mon-year
PowerDown 2:hour-minute
Power On 3: day-mon-year
Power On 3: hour-minute
PowerDown 3:day-mon-year
PowerDown 3:hour-minute
Power On 4: day-mon-year
Power On 4: hour-minute
PowerDown 4:day-mon-year
PowerDown 4:hour-minute
Power On 5: day-mon-year
Power On 5: hour-minute
PowerDown 5:day-mon-year
PowerDown 5:hour-minute
CAPACITY CONTROL
Average Ctrl Water Temp
Differential Water Temp
Water Delta T
Control Point
Reset Amount
Controlled Temp Error
Actual Capacity
Actual Capacity Limit
Actual Chiller Current
Chiller Current Limit
Current At 30% Load A
Current At 30% Load B
Current At 30% Load C
Current At 100% Load A
Current At 100% Load B
Current At 100% Load C
Current Z Multiplier Val
Load/Unload Factor
Active Capacity Override
EHS CAPACITY CONTROL*
EHS Ctrl Override
Requested Electric Stage
Electrical Pulldown?
EXV CONTROL
EXV Position Circuit A
Discharge Superheat A
Suction Superheat A
Suction SH Control Pt A
Cooler Exchange DT Cir A
Cooler Pinch Ctl Point A
EXV Override Circuit A
WC EXV Optimiz Status A
EXV Position Circuit B
Discharge Superheat B
Suction Superheat B
Suction SH Control Pt B
Cooler Exchange DT Cir B
Cooler Pinch Ctl Point B
EXV Override Circuit B
WC EXV Optimiz status
EXV Position Circuit C
Discharge Superheat C
Suction Superheat C
Suction SH Control Pt C
Cooler Exchange DT Cir C
Cooler Pinch Ctl Point C
EXV Override Circuit C
WC EXV Optimiz Status
ECONOMIZER CONTROL
Economizer Position A
Economizer Superheat A
Economizer SH Setpoint A
EXV Override Circuit A
Economizer Position B
Economizer Superheat B
Economizer SH Setpoint B
EXV Override Circuit B
Economizer Position C
Economizer Superheat C
Economizer SH Setpoint C
EXV Override Circuit C
RANGE
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
°F
°F
°F
°F
°F
°F
UNITS
nnnnnn
nnnn
nnnnnn
nnnn
nnnnnn
nnnn
nnnnnn
nnnn
nnnnnn
nnnn
nnnnnn
nnnn
nnnnnn
nnnn
nnnnnn
nnnn
nnnnnn
nnnn
nnnnnn
nnnn
ddmmyy
hhmm
ddmmyy
hhmm
ddmmyy
hhmm
ddmmyy
hhmm
ddmmyy
hhmm
ddmmyy
hhmm
ddmmyy
hhmm
ddmmyy
hhmm
ddmmyy
hhmm
ddmmyy
hhmm
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
nnn
nnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
±n.n
±nnn.n
nn
°F
°F
^F
°F
^F
^F
%
%
amps
amps
amps
amps
amps
amps
amps
amps
0/0
nn
nn
True/False
POINT NAME
sct_sp_a
sct_fu_a
sct_sp_b
sct_fu_b
sct_sp_c
sct_fu_c
drva_pwt
drva_i
SET A_DRVA
SET B_DRVA
SET C_DRVA
date_on1
time_on1
date_of1
time_of1
date_on2
time_on2
date_of2
time_of2
date_on3
time_on3
date_of3
time_of3
date_on4
time_on4
date_of4
time_of4
date_on5
time_on5
date_of5
time_of5
ctrl_avg
diff_wt
delta_t
CTRL_PNT
reset
tp_error
cap_t
cap_lim
TOT_CURR
CURR_LIM
cur_30_a
cur_30_b
cur_30_c
cur100_a
cur100_b
cur100_c
zm
smz
over_cap
over_ehs
eh_stage
ehspulld
nnn.n
nnn.n
nn.n
nn.n
nn.n
nn.n
nn
%
%
^F
^F
^F
^F
EXV_A
DSH_A
SH_A
sh_sp_a
pinch_a
pinch_spa
ov_exv_a
nnn.n
nnn.n
nn.n
nn.n
nn.n
nn.n
nn
%
%
^F
^F
^F
^F
EXV_B
DSH_B
SH_B
sh_sp_b
pinch_b
pinch_spb
ov_exv_b
nnn.n
nnn.n
nn.n
nn.n
nn.n
nn.n
nn
%
%
^F
^F
^F
^F
EXV_C
DSH_C
SH_C
sh_sp_c
pinch_c
pinch_spc
ov_exv_c
nnn.n
nn.n
nn.n
nn
nnn.n
nn.n
nn.n
nn
nnn.n
nn.n
nn.n
nn
%
^F
^F
EXV_EC_A
eco_sha
ecsh_spa
ov_eco_a
EXV_EC_B
eco_shb
ecsh_spb
ov_eco_b
EXV_EC_C
eco_shc
ecsh_spc
ov_eco_c
%
^F
^F
%
^F
^F
*Not supported.
152
WRITE STATUS
APPENDIX C — CCN TABLES (cont)
MAINTENANCE DISPLAY TABLES (cont)
TABLE
MSTSLAVE
DISPLAY NAME
MASTER/SLAVE CONTROL
Unit is Master or Slave
Master Control Type*
Master/Slave Ctrl Active
Lead Unit is the:
Slave Chiller State†
Slave Chiller Total Cap
Lag Start Delay**
Lead/Lag Hours Delta
Lead/Lag Changeover?**
Lead Pulldown?
Master/Slave Error
Max Available Capacity?††
Slave Lagstat
RANGE
Disable/Master/Slave
Local/Remote/CCN
True/False
Master/Slave
0=Chiller is off
1=Valid Run State in
CCN Mode
2=Unused for this control
3=Chiller is in local mode
4=Power fail restart in
progress
5=Shudown due to fault
6=Communication failure
0-100
1-30
±nnnnn
Yes/No
Yes/No
nn
True/False
0=Unit not configured
as a slave chiller
1=Slave pump
configuration error
(ms_error=1)
2=Unit configured as
slave chiller with
lwt_opt=no (entering
water control) with
pump control
(lag_pump=0)
3=Unit configured as slave
chiller with lwt_opt=yes
(leaving water control)
with pump control
(lag_pump=0)
4=Unit Configured as slave
chiller with lwt_opt=no
(entering water control)
with no pump control
(lag_pump=1)
5=Unit configured as slave
chiller with lwt_opt=yes
(leaving water control)
with no pump control
(lag_pump=1)
UNITS
POINT NAME
WRITE STATUS
mstslv
ms_ctrl
ms_activ
lead_sel
slv_stat
%
minutes
hours
slv_capt
l_strt_d
ll_hr_d
ll_chang
ll_pull
ms_error
cap_max
lagstat
*Always CCN for the slave chiller.
†Slave chiller chillstat value
**This decision is consistent for master chiller only. It shall be set by default to 0 for the slave chiller.
††This item is true when chiller has loaded its total available capacity tonnage.
TABLE
OCCMAINT
TABLE
PR_LIMIT
DISPLAY NAME
Current Mode (1=occup.)
Current Occp Period #
Timed-Override in Effect
Timed-Override Duration
Current Occupied Time
Current Unoccupied Time
Next Occupied Day
Next Occupied Time
Next Unoccupied Day
Next Unoccupied Time
Prev Unoccupied Day
Prev Unoccupied Time
RANGE
0/1
1 to 8
Yes/No
0-4
00:00-23:59
00:00-23:59
Mon-Sun
00:00-23:59
Mon-Sun
00:00-23:59
Mon-Sun
00:00-23:59
UNITS
POINT NAME
MODE
PER_NO
OVERLAST
OVR_HRS
STRTTIME
ENDTIME
NXTOCDAY
NXTOCTIM
NXTUNDAY
NXTUNTIM
PRVUNDAY
PRVUNTIM
WRITE STATUS
DISPLAY NAME
Discharge A Temp Average
Discharge A Temp Rate
Discharge A Gas Limit
Suction A Temp Average
Discharge B Temp Average
Discharge B Temp Rate
Discharge B Gas Limit
Suction B Temp Average
Discharge C Temp Average
Discharge C Temp Rate
Discharge C Gas Limit
Suction C Temp Average
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
±nnn.n
UNITS
POINT NAME
sdt_m_a
sdt_mr_a
sdtlim_a
sst_m_a
sdt_m_b
sdt_mr_b
sdtlim_b
sst_m_b
sdt_m_c
sdt_mr_c
sdtlim_c
sst_m_c
WRITE STATUS
UNITS
nn
POINT NAME
S_RESET
WRITE STATUS
forcible
Normal/Low/Disable
Normal/Low/Disable
charge_m
wloop_m
0-1000/Alert/Disable
0-1000/Alert/Disable
0-1000/Alert
0-1000/Alert
0-1000/Alert/Disable
0-1000/Alert
0-1000/alert
0-1000/Alert
cpump1_m
cpump2_m
hpump1_m
hpump2_m
wfilte_m
ofiLta_m
ofiLtb_m
ofiLtc_m
hours
RANGE
°F
^F
°F
°F
°F
^F
°F
°F
°F
^F
°F
°F
NOTE: Table for display only. Used for Cooling and Heat Pump Compressor Envelope.
TABLE
SERMAINT
DISPLAY NAME
Reset Maintenance Alert
1 to 11: reset individually
12: reset all
OPERATION WARNINGS
1 — Refrigerant Charge
2 — Water Loop Size
GENERAL SERVICING DELAYS
3 — Cooler Pump 1 (days)
4 — Cooler Pump 2 (days)
5 — Condenser Pump 1 (days)
6 — Condenser Pump 2 (days)
7 — Water Filter (days)
8 — Cp A Oil Filter (days)
9 — Cp B Oil Filter (days)
10 — CP.C Oil Filter (days)
RANGE
153
APPENDIX C — CCN TABLES (cont)
SERVICE CONFIGURATION TABLES
TABLE
DISPLAY NAME
RANGE
DEFAULT
TABLE USED FOR DISABLE COMPRESSORS (see notes)
CP_UNABL
Compressor A Disable
No/Yes
(See Notes)
Compressor B Disable
No/Yes
Compressor C Disable*
No/Yes
FACTORY
Unit Type
1 (Air Cooled)
(See Notes)
2 (Heat Pump)
Unit Capacity
0 to 1800**
Power Frequence 60HZ Sel
Yes/No
Power Supply Voltage
200 to 660
NB Fans on Varifan Cir A
0 to 6
NB Fans on Varifan Cir B
0 to 6
NB Fans on Varifan Cir C
0 to 6
Soft Starter Select*
Yes/No
Wye Delta Start Select
Yes/No
Air Cooled Reclaim Sel*
Yes/No
Free Cooling Select*
Yes/No
Cooler Heater Select
0 to 2
0 = No Heater
1 = Cooler Heater
2 = Future
Condenser Water Val Sel
Yes/No
Hot Gas Bypass Select
Yes/No
MCHX Exchanger Select
Yes/No
DX Cooler Select
Yes/No
Boiler Command Select*
Yes/No
Energy Management Module
Yes/No
High Tiers Display Selec
No = Use Navigator™
display as user interface
(factory installed)
Yes = Use Touch Pilot™
Display as user interface
(factory installed)
Factory Password
0 to 9999
Hydraulic Transducer Kit*
Yes/No
Cooler Pass Number
1 to 3
VLT Fan Drive Select*
VLT Fan Drive rpm*
High Condensing Select*
Yes/No
Max Condenser LWT=45degC* Yes/No
Condenser probe select*
Yes/No
FACTORY2
Compressor A Config
Must Trip Amps
0 to 600
S1 Config Switch (8 to 1)
00000000 (8 position dip
switch configuration)
Compressor B Config
Must Trip Amps
0 to 600
S1 Config Switch (8 to 1)
00000000 (8 position dip
switch configuration)
Compressor C Config
Must Trip Amps
0 to 600
S1 Config Switch (8 to 1)
00000000 (8 position dip
switch configuration)
Circuit A Total Fans NB
2 to 8
Circuit B Total Fans NB
2 to 8
Circuit C Total Fans NB
0 to 8
EXV A Maximum Steps Numb
0/15000
EXV B Maximum Steps Numb
0/15000
EXV C Maximum Steps Numb
0/15000
Economizer A Steps Numb
0/15000
Economizer B Steps Numb
0/15000
Economizer C Steps Numb
0/15000
UNITS
No
No
No
1
POINT NAME
WRITE
STATUS
un_cp_a
un_cp_b
un_cp_c
unit_typ
Nominal Unit Size
Yes
Nameplate Voltage
1
1
0
No
No
No
No
1
volts
unitsize
freq_60H
voltage
varfan_a
varfan_b
varfan_c
softstar
wye_delt
recl_opt
freecool
heat_sel
No
No
Yes
No
No
No
No
cond_val
hgbp_sel
mchx_sel
dx_sel
boil_sel
emm_nrcp
highdisp
111
No
2
0
0
No
No
No
fac_pass
kithydro
cpass_nb
vlt_sel
vlt_rpm
highcond
max_clwt
condprob
Refer to Appendix D
Refer to Appendix D
cpa_mtac
cpa_s1_c
Refer to Appendix D
Refer to Appendix D
cpb_mtac
cpb_s1_c
Refer to Appendix D
Refer to Appendix D
cpc_mtac
cpc_s1_c
3690
3690
3690
2785†
2785†
2785†
nb_fan_a
nb_fan_b
nb_fan_c
exva_max
exvb_max
exvc_max
eco_cnfa
eco_cnfb
eco_cnfc
4. Used for extra functions with the purpose of energy management such as
occupancy override switch, ice storage, setpoint reset, and demand limit.
5. Compressor capacity will be automatically determined if unit size entered
in FACTORY table matches the values in the unit compressor configuration table.
6. Total number of fans includes fans controlled by a variable speed fan. This
value will be automatically populated if unit size entered in FACTORY
table matches the values in the unit compressor configuration table.
*Not supported.
†0 = No economizer.
**Unit capacity should be entered as nominal size. For DX unit capacity unit
capacity is nominal tonnage. i.e., 92 should be 90 and configure DX cooler
select equal to yes.
NOTES:
1. Table used to disable compressors for maintenance purposes. The
capacity control will consider that these compressors (once set to YES)
are failed manually (no alarm will appear).
2. Enter unit size. This item allows the controls to determine capacity of each
compressor and the total number of fans on each circuit based on a compressor arrangement array (can be viewed in table FACTORY2). It is not
necessary to enter compressor capacity and number of fans on each circuit. See the 30XA Installation Instructions for more information.
3. Number of fans controlled directly by a variable speed fan actuator using
0 to 10 vdc signal. This will enable the controls to determine the remaining
discrete fan staging outputs from the total fans on each circuit.
154
APPENDIX C — CCN TABLES (cont)
SERVICE CONFIGURATION TABLES (cont)
TABLE
MAINTCFG
DISPLAY NAME
MAINTENANCE CONFIG
Servicing Alert
Refrigerant Charge Ctrl
Water Loop Control
CPump 1 Ctl Delay (days)
CPump 2 Ctl Delay (days)
HPump 1 Ctrl Delay (days)*
HPump 2 Ctrl Delay (days)*
Water Filter Ctrl (days)
Oil Filter A Ctrl (days)
Oil Filter B Ctrl (days)
Oil Filter C Ctrl (days)
RANGE
DEFAULT
Enable/Disable
Enable/Disable
Enable/Disable
0-1000
0-1000
0-1000
0-1000
0-1000
0 to 1000
0 to 1000
0 to 1000
UNITS
Disable
Disable
Disable
0
0
0
0
0
0
0
0
POINT NAME
WRITE STATUS
s_alert
charge_c
wloop_c
cpump1_c
cpump2_c
hpump1_c
hpump2_c
wfilte_c
oilfia_c
oilfib_c
oilfic_c
*Not supported.
TABLE
SERVICE1
DISPLAY NAME
Cooler Fluid Type
Flow Switch SP*
Brine Freeze Setpoint
Brine Minimum Fluid Temp
Condenser Fluid Type*
Entering Fluid Control
Prop PID Gain Varifan
Int PID Gain Varifan
Deri PID Gain Varifan
Maximum Ducted Fan Speed*
EXV A Superheat Setpoint
EXV B Superheat Setpoint
EXV C Superheat Setpoint
Pinch offset circuit A
Pinch offset circuit B
Pinch offset circuit C
EXV MOP Setpoint
High Pressure Threshold
Cooler Heater Delta Spt
Auto Start When SM Lost
3way Valve Min Position*
3way Valve Max Position*
Economizer SH Setpoint A
Economizer SH Setpoint B
Economizer SH Setpoint C
Fast Loading Sequence
EWT Probe on Cir A Side
Current Offset Cir A
Current Offset Cir B
Current Offset Cir C
RANGE
1/2
1=Water
2=Brine
0-60
–20.0-34.0
10.0-34.0
1/2
1=Water
2=Brine
Yes/No
–20.0-20.0
–5.0-5.0
–20.0-20.0
20-100
7.2-44
7.2-44
7.2-44
–5.4-5.4
–5.4-5.4
–5.4-5.4
40-55
200-290
1-6
Enable/Disable
0-50
20-100
5-15
5-15
5-15
0-4
Yes/No
DEFAULT
UNITS
1
1
34
38
1
°F
°F
No
2.0
0.2
0.4
100
14.4†
14.4†
14.4
0
0
–3.6
62
275.5
2
Disable
0
100
10.8
10.8
10.8
0
Yes
0
0
0
*Not supported. Must be configured at default.
†Default superheat setpoint for DX cooler unit see table below:
SUPERHEAT SETPOINT FOR DX COOLER
UNIT SIZE
FLUID
CKT.
082-242
262-302
327-352
Water
A
15
10
10
LWT 40 F
B
15
15
10
Brine
A
25
20
20
LWT < 40 F
B
25
25
20
NOTE: This table shall be downloadable at any time. However, modified value
shall not be used by tasks until the unit is in OFF state. This shall not apply to
the Varifan gains that shall be modified at any time and used immediately by
the head pressure control tasks even if the unit is in operation.
155
%
^F
^F
^F
^F
^F
^F
°F
psi
^F
%
%
^F
^F
^F
amps
amps
amps
POINT NAME
flui_typ
flow_sp
freezesp
mini_lwt
cond_typ
ewt_opt
hd_pg
hd_ig
hd_dg
fan_max
sh_sp_a
sh_sp_b
sh_sp_c
p_ofst_a
p_ofst_b
p_ofst_c
mop_sp
hp_th
heatersp
auto_sm
min_3w
max_3w
esh_sp_a
esh_sp_b
esh_sp_c
fastload
ewt_cirA
cur_offA
cur_offB
cur_offC
WRITE STATUS
APPENDIX C — CCN TABLES (cont)
SERVICE CONFIGURATION TABLES (cont)
TABLE
DISPLAY NAME
RANGE
TABLE TO BE USED FOR RUN TIMES UPDATE IN CASE OF MBB REPLACEMENT
UPDHRFAN
Free Cooling A Pump Hours
0
Free Cooling B Pump Hours
0
Circuit A Defrost Number
0
Circuit B Defrost Number
0
Circuit A Fan #1 Hours
0
Circuit A Fan #2 Hours
0
Circuit A Fan #3 Hours
0
Circuit A Fan #4 Hours
0
Circuit A Fan #5 Hours
0
Circuit A Fan #6 Hours
0
Circuit A Fan #7 Hours
0
Circuit A Fan #8 Hours
0
Circuit A Fan #9 Hours
0
Circuit A Fan #10 Hours
0
Circuit B Fan #1 Hours
0
Circuit B Fan #2 Hours
0
Circuit B Fan #3 Hours
0
Circuit B Fan #4 Hours
0
Circuit B Fan #5 Hours
0
Circuit B Fan #6 Hours
0
Circuit B Fan #7 Hours
0
Circuit B Fan #8 Hours
0
Circuit B Fan #9 Hours
0
Circuit B Fan #10 Hours
0
Circuit C Fan #1 Hours
0
Circuit C Fan #2 Hours
0
Circuit C Fan #3 Hours
0
Circuit C Fan #4 Hours
0
Circuit C Fan #5 Hours
0
Circuit C Fan #6 Hours
0
Circuit C Fan #7 Hours
0
Circuit C Fan #8 Hours
0
UNITS
hours
hours
POINT NAME
WRITE STATUS
hr_fcp_a
hr_fcp_b
nb_def_a
nb_def_b
hr_fana1
hr_fana2
hr_fana3
hr_fana4
hr_fana5
hr_fana6
hr_fana7
hr_fana8
hr_fana9
hrfana10
hr_fanb1
hr_fanb2
hr_fanb3
hr_fanb4
hr_fanb5
hr_fanb6
hr_fanb7
hr_fanb8
hr_fanb9
hrfanb10
hr_fanc1
hr_fanc2
hr_fanc3
hr_fanc4
hr_fanc5
hr_fanc6
hr_fanc7
hr_fanc8
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
hours
NOTE: This table shall be used for purposes of transplanting the devices run
hours in the event of a module hardware failure or software upgrade via
downloading. It shall be usable only if all items are still null. Afterwards, its
access shall be denied.
TABLE
DISPLAY NAME
RANGE
TABLE TO BE USED FOR RUN TIMES UPDATE IN CASE OF MBB REPLACEMENT
UPDTHOUR
Machine Operating Hours
0
Machine Starts
0
Compressor A Hours
0
Compressor A Starts
0
Compressor B Hours
0
Compressor B Starts
0
Compressor C Hours
0
Compressor C Starts
0
Water Pump #1 Hours
0
Water Pump #2 Hours
0
Condenser Pump #1 Hours
0
NOTE: This table shall be used for purposes of transplanting the devices run
hours and starts in the event of a module hardware failure or software upgrade
via downloading. It shall be usable only if all items are still null. Afterwards, its
access shall be denied.
156
UNITS
hours
hours
hours
hours
hours
hours
hours
POINT NAME
hr_mach
st_mach
hr_cp_a
st_cp_a
hr_cp_b
st_cp_b
hr_cp_c
st_cp_c
hr_cpum1
hr_cpum2
hr_hpum1
WRITE STATUS
APPENDIX D — 30XA080-500 CPM DIP SWITCH ADDRESSES
ACROSS-THE-LINE START
ON
1
30XA
UNIT
SIZE
VOLTAGE
CPM DIP
(3 ph,
SWITCHES
60 Hz)
575
460
080,
082
380
230
200
575
460
090,
092
380
230
200
575
460
100,
102
380
230
200
575
110,
112
460
380
575
120,
122
460
380
575
140,
142
460
380
575
160,
162
460
380
575
180,
182
460
380
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
2
3
CIRCUIT A
4
5
6
a30-4254
8
CIRCUIT B
CIRCUIT C
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
LEGEND
CPM
MTA
7
— Compressor Protection Module
— Must Trip Amps
157
1
2
3
4
5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
6
7
8
MTA
MTA
MTA
SETTING SETTING SETTING
CIRCUIT CIRCUIT CIRCUIT
A
B
C
70
70
—
92
92
—
106
106
—
184
184
—
204
204
—
72
72
—
94
94
—
110
110
—
190
190
—
208
208
—
80
80
—
104
104
—
122
122
—
210
210
—
232
232
—
98
80
—
128
104
—
148
122
—
98
98
—
128
128
—
148
148
—
152
80
—
198
104
—
230
122
—
176
98
—
230
128
—
266
148
—
152
152
—
198
198
—
230
230
—
APPENDIX D — 30XA080-500 CPM DIP SWITCH ADDRESSES (cont)
ACROSS-THE-LINE START (cont)
30XA
UNIT
SIZE
VOLTAGE
CPM DIP
(3 ph,
SWITCHES
60 Hz)
575
200,
202
460
380
575
220,
222
460
380
575
240,
242
460
380
575
260,
262
460
380
575
280,
282
460
380
575
300,
302
460
380
575
325,
327
460
380
575
350,
352
460
380
575
400
460
380
575
450
460
380
575
500
460
380
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
CIRCUIT A
CIRCUIT B
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
ON
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
ON
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
LEGEND
CPM
MTA
CIRCUIT C
1
— Compressor Protection Module
— Must Trip Amps
158
1
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
2
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
3
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
4
5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
OFF ON
ON OFF
OFF ON
ON ON
OFF ON
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF OFF
6
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
MTA
MTA
MTA
SETTING SETTING SETTING
CIRCUIT CIRCUIT CIRCUIT
C
B
A
176
176
—
230
230
—
266
266
—
210
176
—
274
230
—
318
266
—
210
210
—
274
274
—
318
318
—
286
176
—
374
230
—
434
266
—
286
210
—
374
274
—
434
318
—
338
210
—
446
274
—
514
318
—
286
286
—
374
374
—
434
434
—
338
286
—
446
374
—
514
434
—
210
210
286
274
274
374
318
318
434
338
152
338
446
198
446
514
230
514
338
210
338
446
274
446
514
318
514
APPENDIX D — 30XA080-500 CPM DIP SWITCH ADDRESSES (cont)
WYE DELTA START
30XA
UNIT
SIZE
VOLTAGE
CPM DIP
(3 Ph,
SWITCHES
60 Hz)
575
460
080,
082
380
230
200
575
460
090,
092
380
230
200
575
460
100,
102
380
230
200
575
460
110,
112
380
230
200
575
460
120,
122
380
230
200
575
460
140,
142
380
230
200
575
460
160,
162
380
230
200
575
460
180,
182
380
230
200
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
CIRCUIT A
CIRCUIT B
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
LEGEND
CPM
MTA
CIRCUIT C
1
— Compressor Protection Module
— Must Trip Amps
159
1
2
3
4
5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
6
7
8
MTA
MTA
MTA
SETTING SETTING SETTING
CIRCUIT CIRCUIT CIRCUIT
C
B
A
70
70
—
92
92
—
106
106
—
184
184
—
204
204
—
72
72
—
94
94
—
110
110
—
190
190
—
208
208
—
80
80
—
104
104
—
122
122
—
210
210
—
232
232
—
98
80
—
128
104
—
148
122
—
254
210
—
282
232
—
98
98
—
128
128
—
148
148
—
254
254
—
282
282
—
152
80
—
198
104
—
230
122
—
398
210
—
438
232
—
176
98
—
230
128
—
266
148
—
462
254
—
506
282
—
152
152
—
198
198
—
230
230
—
398
398
—
438
438
-—
APPENDIX D — 30XA080-500 CPM DIP SWITCH ADDRESSES (cont)
WYE DELTA START (cont)
30XA
UNIT
SIZE
VOLTAGE
CPM DIP
(3 Ph,
SWITCHES
60 Hz)
575
460
200,
202
380
230
200
575
460
220,
222
380
230
200
575
460
240,
242
380
230
200
575
260,
262
460
380
575
280,
282
460
380
575
300,
302
460
380
575
325,
327
460
380
575
350,
352
460
380
575
400
460
380
575
450
460
380
575
500
460
380
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
S1
S2
CIRCUIT A
CIRCUIT B
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
ON
OFF
ON
ON
OFF
ON
OFF
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
ON
OFF
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
LEGEND
CPM
MTA
CIRCUIT C
1
— Compressor Protection Module
— Must Trip Amps
160
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
2
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
3
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
4
5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ON OFF
ON ON
ON OFF
OFF OFF
ON OFF
OFF OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF OFF
6
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
7
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
8
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
MTA
MTA
MTA
SETTING SETTING SETTING
CIRCUIT CIRCUIT CIRCUIT
B
C
A
176
176
—
230
230
—
266
266
—
462
462
—
506
506
—
210
176
—
274
230
—
318
266
—
550
462
—
602
506
—
210
210
—
274
274
—
318
318
—
550
550
—
602
602
—
286
176
—
374
230
—
434
266
—
286
210
—
374
274
—
434
318
—
338
210
—
446
274
—
514
318
—
286
286
—
374
374
—
434
434
—
338
286
—
446
374
—
514
434
—
210
210
286
274
274
374
318
318
434
338
152
338
446
198
446
514
230
514
338
210
338
446
274
446
514
318
514
161
Serv. Valve
(SSV Option)
Flow Switch
Sightglass
Dry Eye
EXV
7
8
10
3
6
5
Oil Filter
Oil Level
Switch
2
4
9
Oil Heater
Muffler
3
6
5
1
Cooler Heater
Motor Cooling
Solenoid Valve
Relief Valve
10
Serv. Valve
(SSV Option)
Suction Service Valve (Option)
Oil Filter
Oil Level
Switch
Minimum Load
Control Valve
(Option)
Cooler Heater
Suction Service Valve (Option)
1
9
4
Oil Heater
Muffler
2
Motorized Discharge
Service Valve
Condenser Coil
Condenser Coil
Motorized Discharge
Service Valve
Condenser Coil
11
Condenser Fans
30XA080 Flooded Cooler Units
Load Solenoid 1
Load Solenoid 2
APPENDIX E — PIPING AND INSTRUMENTATION
Condenser Coil
Condenser Fans
Relief Valve
Load Solenoid 2
Load Solenoid 1
Motor Cooling
Solenoid Valve
Filter Drier
Liquid Line
Service Valve
a30-4493
Sightglass
Dry Eye
EXV
Filter Drier
Liquid Line
Service Valve
SSV
1
2
3
4
5
6
7
8
9
10
11
—
—
—
—
—
—
—
—
—
—
—
—
Fusible Plug
Device Connection
High Flow Shrader Valve
LEGEND
Suction Service Valve
Suction Pressure
Discharge Pressure
Economizer Pressure
Oil Pressure
High Pressure Switch
Discharge Gas Thermistor
Entering Water Thermistor
Leaving Water Thermistor
Return Gas Thermistor
Economizer Gas Thermistor
Outside Air Thermistor
Refrigerant Access Fitting
a30-4494
162
7
8
10
3
6
5
Oil Filter
Oil Level
Switch
2
4
9
Oil Heater
Muffler
3
6
5
1
Cooler Heater
Muffler
Relief Valve
10
Serv. Valve
(SSV Option)
Suction Service Valve (Option)
Oil Filter
Oil Level
Switch
Minimum Load
Control Valve
(Option)
Cooler Heater
Suction Service Valve (Option)
1
9
4
Oil Heater
Muffler
2
Motorized Discharge
Service Valve
Condenser Coil
Condenser Coil
Motorized Discharge
Service Valve
Condenser Coil
11
Condenser Fans
Condenser Coil
Condenser Fans
SSV
1
2
3
4
5
6
7
8
9
10
11
—
—
—
—
—
—
—
—
—
—
—
—
Economizer EXV
Sightglass
Dry Eye
Sightglass
Dry Eye
EXV
Economizer
(SSV
Option)
Econo.
Serv. Valve
Filter Drier
Liquid Line
Service Valve
30XA090, 100, 110, 120, 140, 160, 180, 200, 220, 240, 260, 280, 300, 325, 350 Flooded Cooler Units
Relief Valve
Muffler
Serv. Valve
(SSV Option)
Flow Switch
Sightglass
Dry Eye
EXV
Economizer
(SSV
Option)
Econo.
Serv. Valve
Economizer EXV
Sightglass
Dry Eye
Filter Drier
Liquid Line
Service Valve
Load Solenoid 2
Load Solenoid 1
APPENDIX E — PIPING AND INSTRUMENTATION (cont)
Load Solenoid 1
Load Solenoid 2
Fusible Plug
Device Connection
High Flow Shrader Valve
LEGEND
Suction Service Valve
Suction Pressure
Discharge Pressure
Economizer Pressure
Oil Pressure
High Pressure Switch
Discharge Gas Thermistor
Entering Water Thermistor
Leaving Water Thermistor
Return Gas Thermistor
Economizer Gas Thermistor
Outside Air Thermistor
Refrigerant Access Fitting
30XA082 DX Cooler Units
APPENDIX E — PIPING AND INSTRUMENTATION (cont)
a30-5327
163
30XA092, 102, 112, 122, 142, 162, 182, 202, 222, 242, 262, 282, 302, 327, 352 DX Cooler Units
APPENDIX E — PIPING AND INSTRUMENTATION (cont)
a30-5328
164
APPENDIX F — MAINTENANCE SUMMARY AND LOG SHEETS
30XA Maintenance Interval Requirements
WEEKLY
Compressor
Cooler
Condenser
Check Oil Level.
Economizer
None.
Controls
Inspect and clean all coils as necessary.
Starter
None.
Review Alarm/Alert History.
None.
MONTHLY
Compressor
Check Oil Level.
Economizer
Cooler
Check moisture.
Controls
Condenser
Inspect and clean all coils as necessary.
Starter
None.
Check accuracy of tranducers and thermistors. Verify flow
switch operation.
Inspect all contactors.
QUARTERLY
Compressor
Cooler
Condenser
Check Oil Level
Economizer
Check refrigerant charge. Check for leaks.
Controls
Check for leaks.
Starter
Check all connections for leaks.
Perform an Automated Controls test. Run all Compressors
and ensure proper operation. Verify operation of units flow
switch.
None.
ANNUALLY
Compressor
Check Oil Level. Obtain and test an oil sample.
Check approach on unit to determine if tubes
need cleaning (flooded cooler units only).
Cooler
Economizer
Controls
Check for temperature drop across filter drier
to determine if filter needs replacement.
Condenser
Check fan blades and motors for cracks and
loose bolts. Tighten bolts as needed.
Starter
NOTE: Equipment failures caused by lack of adherence to the Maintenance Interval Requirements are not covered under warranty.
165
Verify proper operation of EXVs.
Perform an Automated Controls test. Run all Compressors
and ensure proper operation.
Inspect all electrical connections and tighten as needed.
Measure current to each compressor and inspect
contactors.
APPENDIX F — MAINTENANCE SUMMARY AND LOG SHEETS (cont)
30XA Monthly Maintenance Log
Month
Date
Operator
UNIT SECTION
Compressor
Cooler
Condenser
166
Controls
Starter
System
1
/
ACTION
Change Oil Filter (Screw Compressors)
Send Oil Sample Out for Analysis
Leak Test
Inspect and Clean Cooler Tubes*
Inspect Cooler Heater
Inspect Relief Valves
Leak Test
Record Water Pressure Differential (PSI)
Inspect Water Pumps
Eddy Current Test
Leak Test
Inspect and Clean Condenser Coils
Inspect Relief Valves
General Cleaning and Tightening Connections
Check Pressure Transducers for Accuracy
Verify Flow Switch Operation
Confirm Accuracy of Thermistors
General Tightening and Cleaning Connections
Inspect All Contactors
Check Refrigerant Charge
Verify Operation of EXVs
Record System Superheat
2
/
UNIT
yes/no
yes/no
yes/no
yes/no
amps
yes/no
yes/no
PSI
yes/no
yes/no
yes/no
yes/no
yes/no
yes/no
yes/no
yes/no
yes/no
yes/no
yes/no
yes/no
yes/no
deg. F
*Flooded cooler units only.
NOTE: Equipment failures caused by lack of adherence to the Maintenance Interval Requirements
are not covered under warranty.
/
3
/
/
4
/
/
5
/
/
6
/
/
7
/
/
8
/
ENTRY
Year 1 then As Needed
Annually
Every 3 - 5 Years
Every 3 - 5 Years
Annually
Annually
/
9
/
/
/
10
/ /
11
/ /
12
/ /
APPENDIX F — MAINTENANCE SUMMARY AND LOG SHEETS (cont)
30XA Seasonal Shutdown Log
Month
Date
Operator
UNIT SECTION
Cooler
Controls
1
/
2
/
/
3
/
ACTION
Isolate and Drain Waterbox/Cooler
Add Glycol/Water Mixture To Prevent Freeze-up
Do Not Disconnect Control Power
NOTE: Equipment failures caused by lack of adherence to the Maintenance Interval Requirements
are not covered under warranty.
/
4
/
/
5
/
/
6
/
/
7
/
ENTRY
/
8
/
/
9
/
/
/
10
/ /
11
/ /
12
/ /
167
APPENDIX G — BACNET COMMUNICATIONS OPTION
6
5
7 8
2 34
5
6
10's
1
9 0
2 34
7 8
9 0
1
The following section is used to configure the UPC Open
controller which is used when the BACnet* communications
option is selected. The UPC Open controller is mounted in a
separate enclosure below the main control box.
TO ADDRESS THE UPC OPEN CONTROLLER — The
user must give the UPC Open controller an address that is
unique on the BACnet network. Perform the following procedure to assign an address:
1. If the UPC Open controller is powered, pull the screw terminal connector from the controller's power terminals labeled Gnd and HOT. The controller reads the address
each time power is applied to it.
2. Using the rotary switches (see Fig. A and B), set the controller's address. Set the Tens (10's) switch to the tens digit of the address, and set the Ones (1's) switch to the ones
digit.
As an example in Fig. B, if the controller’s address is 25,
point the arrow on the Tens (10's) switch to 2 and the arrow on
the Ones (1's) switch to 5.
1's
Fig. B — Address Rotary Switches
BACNET DEVICE INSTANCE ADDRESS — The UPC
Open controller also has a BACnet Device Instance address.
This Device Instance MUST be unique for the complete BACnet system in which the UPC Open controller is installed. The
Device Instance is auto generated by default and is derived by
adding the MAC address to the end of the Network Number.
The Network Number of a new UPC Open controller is 16101,
but it can be changed using i-Vu® Tools or BACView device.
By default, a MAC address of 20 will result in a Device Instance of 16101 + 20 which would be a Device Instance of
1610120.
BT485
TERMINATOR
BACNET
CONNECTION
(BAS PORT)
POWER LED
Tx1 LED
Rx1 LED
Tx2 LED
Rx2 LED
23
45
01
8
67 9
EIA-485
JUMPERS
01
8
67 9
23
45
BACNET
BAUD RATE
DIP SWITCHES
ADDRESS
ROTARY
SWITCHES
RUN LED
ERROR LED
Fig. A — UPC Open Controller
*Sponsored by ASHRAE (American Society of Heating,
Refrigerating, and Air Conditioning Engineers).
168
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
CONFIGURING THE BAS PORT FOR BACNET MS/
TP — Use the same baud rate and communication settings for
all controllers on the network segment. The UPC Open controller is fixed at 8 data bits, No Parity, and 1 Stop bit for this
protocol's communications.
If the UPC Open controller has been wired for power, pull
the screw terminal connector from the controller's power terminals labeled Gnd and HOT. The controller reads the DIP
Switches and jumpers each time power is applied to it.
Set the BAS Port DIP switch DS3 to “enable.” Set the BAS
Port DIP switch DS4 to “E1-485.” Set the BMS Protocol DIP
switches DS8 through DS5 to “MSTP.” See Table A.
Fig. C — DIP Switches
Table A — SW3 Protocol Switch Settings
for MS/TP
DS8
Off
DS7
Off
DS6
Off
DS5
Off
DS4
On
Wire the controllers on an MS/TP network segment in a daisy-chain configuration. Wire specifications for the cable are
22 AWG (American Wire Gage) or 24 AWG, low-capacitance,
twisted, stranded, shielded copper wire. The maximum length
is 2000 ft.
Install a BT485 terminator on the first and last controller on
a network segment to add bias and prevent signal distortions
due to echoing. See Fig. A, D, and E.
To wire the UPC Open controller to the BAS network:
1. Pull the screw terminal connector from the controller's
BAS Port.
2. Check the communications wiring for shorts and
grounds.
3. Connect the communications wiring to the BAS port’s
screw terminals labeled Net +, Net -, and Shield.
NOTE: Use the same polarity throughout the network
segment.
4. Insert the power screw terminal connector into the UPC
Open controller's power terminals if they are not currently connected.
5. Verify communication with the network by viewing a
module status report. To perform a module status report
using the BACview keypad/display unit, press and hold
the “FN” key then press the “.” Key.
DS3
Off
Verify that the EIA-485 jumpers below the CCN Port are set
to EIA-485 and 2W.
The example in Fig. C shows the BAS Port DIP Switches
set for 76.8k (Carrier default) and MS/TP.
Set the BAS Port DIP Switches DS2 and DS1 for the appropriate communications speed of the MS/TP network (9600,
19.2k, 38.4k, or 76.8k bps). See Fig. C and Table B.
Table B — Baud Selection Table
BAUD RATE
9,600
19,200
38,400
76,800
DS2
Off
On
Off
On
DS1
Off
Off
On
On
WIRING THE UPC OPEN CONTROLLER TO THE MS/
TP NETWORK — The UPC Open controller communicates
using BACnet on an MS/TP network segment communications
at 9600 bps, 19.2 kbps, 38.4 kbps, or 76.8 kbps.
Fig. D — Network Wiring
169
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
Fig. E — BT485 Terminator Installation
temperature rating specifications list two acceptable alternatives. The Halar specification has a higher temperature rating
and a tougher outer jacket than the SmokeGard specification,
and it is appropriate for use in applications where the user is
concerned about abrasion. The Halar jacket is also less likely to
crack in extremely low temperatures.
NOTE: Use the specified type of wire and cable for maximum
signal integrity.
To install a BT485 terminator, push the BT485 terminator
on to the BT485 connector located near the BACnet connector.
NOTE: The BT485 terminator has no polarity associated with
it.
To order a BT485 terminator, consult Commercial Products
i-Vu Open Control System Master Prices.
MS/TP WIRING RECOMMENDATIONS — Recommendations are shown in Tables C and D. The wire jacket and UL
Table C — MS/TP Wiring Recommendations
SPECIFICATION
Cable
Conductor
Insulation
Color Code
Twist Lay
Shielding
Jacket
DC Resistance
Capacitance
Characteristic Impedance
Weight
UL Temperature Rating
Voltage
Listing
AWG
CL2P
DC
FEP
NEC
O.D.
TC
UL
—
—
—
—
—
—
—
—
RECOMMMENDATION
Single twisted pair, low capacitance, CL2P, 22 AWG (7x30), TC foam FEP, plenum rated cable
22 or 24 AWG stranded copper (tin plated)
Foamed FEP 0.015 in. (0.381 mm) wall 0.060 in. (1.524 mm) O.D.
Black/White
2 in. (50.8 mm) lay on pair 6 twists/foot (20 twists/meter) nominal
Aluminum/Mylar shield with 24 AWG TC drain wire
SmokeGard Jacket (SmokeGard PVC) 0.021 in. (0.5334 mm) wall 0.175 in. (4.445 mm) O.D.
Halar Jacket (E-CTFE) 0.010 in. (0.254 mm) wall 0.144 in. (3.6576 mm) O.D.
15.2 Ohms/1000 feet (50 Ohms/km) nominal
12.5 pF/ft (41 pF/meter) nominal conductor to conductor
100 Ohms nominal
12 lb/1000 feet (17.9 kg/km)
SmokeGard 167°F (75°C)
Halar -40 to 302°F (-40 to 150°C)
300 Vac, power limited
UL: NEC CL2P, or better
LEGEND
American Wire Gage
Class 2 Plenum Cable
Direct Current
Fluorinated Ethylene Polymer
National Electrical Code
Outside Diameter
Tinned Copper
Underwriters Laboratories
170
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
Table D — Open System Wiring Specifications and Recommended Vendors
WIRING SPECIFICATIONS
Wire Type
RECOMMENDED VENDORS AND PART NUMBERS
Connect Air
Contractors
Belden RMCORP Wire and Cable
International
Description
22 AWG, single twisted shielded pair, low capacitance, CL2P,
TC foam FEP, plenum rated. See MS/TP Installation Guide for
specifications.
MS/TP
Network (RS-485) 24 AWG, single twisted shielded pair, low capacitance, CL2P,
TC foam FEP, plenum rated. See MS/TP Installation Guide
for specifications.
Rnet
4 conductor, unshielded, CMP, 18 AWG, plenum rated.
AWG
CL2P
CMP
FEP
TC
—
—
—
—
—
W221P-22227
—
25160PV
CLP0520LC
W241P-2000F
82841
25120-OR
—
W184C-2099BLB
6302UE
21450
CLP0442
LEGEND
American Wire Gage
Class 2 Plenum Cable
Communications Plenum Rated
Fluorinated Ethylene Polymer
Tinned Copper
number and CCN Bus number. The factory default settings for
CCN Element and CCN Bus number are 1 and 0 respectively.
If modifications to the default Element and Bus number are
required, both the ComfortLink™ and UPC Open configurations must be changed.
The following configurations are used to set the CCN Address and Bus number in the ComfortLink control. These configurations can be changed using the scrolling marquee display
or accessory Navigator™ handheld device.
Configuration→CCN→CCN.A (CCN Address)
Configuration→CCN→CCN.B (CCN Bus Number)
The following configurations are used to set the CCN Address and Bus Number in the UPC Open controller. These configurations can be changed using the accessory BACview6 display.
Navigation: BACview→CCN
Home: Element Comm Stat
Element: 1
Bus: 0
LOCAL ACCESS TO THE UPC OPEN CONTROLLER — The user can use a BACview6 handheld keypad display unit or the Virtual BACview software as a local user interface to an Open controller. These items let the user access the
controller network information. These are accessory items and
do not come with the UPC Open controller.
The BACview6 unit connects to the local access port on the
UPC Open controller. See Fig. F. The BACview software must
be running on a laptop computer that is connected to the local
access port on the UPC Open controller. The laptop will require an additional USB link cable for connection.
See the BACview Installation and User Guide for instructions on connecting and using the BACview6 device.
To order a BACview6 Handheld (BV6H), consult Commercial Products i-Vu® Open Control System Master Prices.
CONFIGURING THE UPC OPEN CONTROLLER'S
PROPERTIES — The UPC Open device and ComfortLink
control must be set to the same CCN Address (Element)
Fig. F — BACview6 Device Connection
171
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
If the UPC Open controller is used with the chiller application of Lead/Lag/Standby, all chillers and UPC Open's CCN element numbers must be changed to a unique number in order
to follow CCN specifications. In this application, there can
only be a maximum of 3 UPC Open controllers on a CCN bus.
For the CCN Alarm Acknowledger configuration, the UPC
Open controller defaults to CCN Acknowledger. If a Chiller
Lead/Lag/Standby application is being used, then the Carrier
technician must change the configuration to only one CCN Acknowledger on the CCN bus.
For the CCN Time Broadcaster configuration, the UPC
Open controller defaults to CCN Time Broadcaster. If the
Chiller Lead/Lag/Standby application is used, then the Carrier
technician must change the configuration to only one CCN
Time Broadcaster on the CCN bus.
TROUBLESHOOTING — If there are problems wiring or
addressing the UPC Open controller, contact Carrier Technical
Support.
COMMUNICATION LEDS — The LEDs indicate if the
controller is communicating with the devices on the network.
See Tables E and F. The LEDs should reflect communication
traffic based on the baud rate set. The higher the baud rate the
more solid the LEDs become. See Fig. A for location of LEDs
on UPC Open module.
REPLACING THE UPC OPEN BATTERY — The UPC
Open controller's 10-year lithium CR2032 battery provides a
minimum of 10,000 hours of data retention during power
outages.
IMPORTANT: Power must be ON to the UPC Open controller when replacing the battery, or the date, time, and
trend data will be lost.
Remove the battery from the controller, making note of the
battery's polarity. Insert the new battery, matching the battery's
polarity with the polarity indicated on the UPC Open
controller.
NETWORK POINTS LIST — The points list for the controller is shown in Table G.
Table E — LED Status Indicators
LED
Power
Rx
Tx
Run
Error
STATUS
Lights when power is being supplied to the controller. The UPC Open controller is protected by internal solid-state polyswitches on
the incoming power and network connections. These polyswitches are not replaceable and will reset themselves if the condition
that caused the fault returns to normal.
Lights when the controller receives data from the network segment; there is an Rx LED for Ports 1 and 2.
Lights when the controller transmits data to the network segment; there is an Tx LED for Ports 1 and 2.
Lights based on controller status. See Table F.
Lights based on controller status. See Table F.
Table F — Run and Error LEDs Controller and Network Status Indication
RUN LED
2 flashes per second
2 flashes per second
2 flashes per second
2 flashes per second
2 flashes per second
5 flashes per second
5 flashes per second
7 flashes per second
14 flashes per second
ERROR LED
Off
2 flashes, alternating with Run LED
3 flashes, then off
1 flash per second
On
On
Off
7 flashes per second, alternating with Run LED
14 flashes per second, alternating with Run LED
172
STATUS
Normal
Five minute auto-restart delay after system error
Controller has just been formatted
Controller is alone on the network
Exec halted after frequent system errors or control programs halted
Exec start-up aborted, Boot is running
Firmware transfer in progress, Boot is running
Ten second recovery period after brownout
Brownout
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
Table G — Network Points List
BACNET
OBJECT ID
AV:1
AV:2
AV:3
AV:4
AV:5
AV:6
AV:7
AV:8
AV:9
AV:10
AV:11
AV:12
AV:13
AV:14
AV:15
AV:16
AV:17
AV:18
AV:19
AV:20
AV:21
AV:22
AV:23
AV:24
AV:25
AV:26
AV:27
AV:28
AV:29
AV:30
AV:31
AV:32
AV:33
AV:34
AV:35
AV:36
AV:37
AV:38
AV:39
AV:40
AV:41
AV:42
AV:43
AV:44
AV:45
AV:46
AV:47
AV:48
AV:49
AV:50
AV:51
AV:52
Circuit A Fan #1 Hours
Circuit A Fan #2 Hours
Circuit A Fan #3 Hours
Circuit A Fan #4 Hours
Circuit A Fan #5 Hours
Circuit A Fan #6 Hours
Circuit A Fan #7 Hours
Circuit A Fan #8 Hours
Circuit A Fan #9 Hours
Circuit A Fan #10 Hours
Circuit B Fan #1 Hours
Circuit B Fan #2 Hours
Circuit B Fan #3 Hours
Circuit B Fan #4 Hours
Circuit B Fan #5 Hours
Circuit B Fan #6 Hours
Circuit B Fan #7 Hours
Circuit B Fan #8 Hours
Circuit B Fan #9 Hours
Circuit B Fan #10 Hours
Circuit C Fan #1 Hours
Circuit C Fan #2 Hours
Circuit C Fan #3 Hours
Circuit C Fan #4 Hours
Circuit C Fan #5 Hours
Circuit C Fan #6 Hours
Circuit C Fan #7 Hours
Circuit C Fan #8 Hours
Compressor Suction Temp
Compressor Suction Temp
Compressor Suction Temp
Discharge Gas Temp
Discharge Gas Temp
Discharge Gas Temp
Discharge Pressure
Discharge Pressure
Discharge Pressure
Economizer Gas Temp
Economizer Gas Temp
Economizer Gas Temp
Economizer Pressure
Economizer Pressure
Economizer Pressure
EXV Position
EXV Position
EXV Position
Fan Staging Number
Fan Staging Number
Fan Staging Number
Head Pressure Actuator Position
Head Pressure Actuator Position
Head Pressure Actuator Position
READ/
WRITE
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
AV:53
Heat/Cool Select
R/W
AV:54
Minutes Left for Start
R
CHWS
DGT
DO
EWT
—
—
—
—
POINT NAME
LEGEND
Chilled Water Switch
EXV
Discharge Gas Thermistor
OAT
Digital Output
R
Entering Water Temperature W
—
—
—
—
UNITS
RANGE
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
hr
°F
°F
°F
°F
°F
°F
psi
psi
psi
°F
°F
°F
psi
psi
psi
%
%
%
%
%
%
0=Cool
1=Heat
2=Auto
min
Expansion Valve
Outdoor Air Temperature
Read
Write
173
DEFAULT
VALUE
BACNET
OBJECT NAME
hr_fana1_1
hr_fana2_1
hr_fana3_1
hr_fana4_1
hr_fana5_1
hr_fana6_1
hr_fana7_1
hr_fana8_1
hr_fana9_1
hrfana10_1
hr_fanb1_1
hr_fanb2_1
hr_fanb3_1
hr_fanb4_1
hr_fanb5_1
hr_fanb6_1
hr_fanb7_1
hr_fanb8_1
hr_fanb9_1
hrfanb10_1
hr_fanc1_1
hr_fanc2_1
hr_fanc3_1
hr_fanc4_1
hr_fanc5_1
hr_fanc6_1
hr_fanc7_1
hr_fanc8_1
suct_t_a_1
suct_t_b_1
suct_t_c_1
dgt_a_1
dgt_b_1
dgt_c_1
dp_a_1
dp_b_1
dp_c_1
eco_tp_a_1
eco_tp_b_1
eco_tp_c_1
econ_p_a_1
econ_p_b_1
econ_p_c_1
exv_a_1
exv_b_1
exv_c_1
fan_st_a_1
fan_st_b_1
fan_st_c_1
hd_pos_a_1
hd_pos_b_1
hd_pos_c_1
hc_sel_1
min_left_1
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
Table G — Network Points List (cont)
BACNET
OBJECT ID
AV:55
AV:56
AV:57
AV:58
AV:59
AV:60
AV:61
AV:62
AV:63
AV:64
AV:65
AV:67
AV:68
AV:69
AV:70
AV:71
AV:72
AV:73
AV:74
AV:75
AV:76
AV:77
AV:78
AV:79
AV:80
AV:81
AV:82
AV:83
AV:84
AV:85
AV:86
AV:87
AV:88
AV:89
AV:90
AV:91
AV:92
READ/
WRITE
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R/W
R
R/W
R
R/W
R
R
R
R
R
R
R
R
R
POINT NAME
Motor Current
Motor Current
Motor Current
Motor Temperature
Motor Temperature
Motor Temperature
Oil Pressure
Oil Pressure
Oil Pressure
Oil Pressure Difference
Oil Pressure Difference
Percent Total Capacity
Percent Total Capacity
Percent Total Capacity
Saturated Condensing Temp
Saturated Condensing Temp
Saturated Condensing Temp
Saturated Suction Temp
Saturated Suction Temp
Saturated Suction Temp
Suction Pressure
Suction Pressure
Suction Pressure
Active Demand Limit Value
Actual Chiller Current
Chiller Current Limit
Controlled Water temp
Control point
Current Setpoint
External Temperature
Lag Capacity Limit Value
Percent Total Capacity
Setpoint Select
Chiller Capacity Signal
CHWS Temperature
Circuit C Heater Temp
Heat/Cool Status
AV:93
Run Status
R
AV:94
AV:95
Cooler Entering Fluid
Cooler Heater Temp
Cooler Leaving Fluid - Prime
Variable
Cooling power
Limit 4-20mA Signal
Optional Space Temp
Reset/Setpoint 4-20mA Signal
Water pressure before cooler
Water pressure after cooler
Water pressure before filter
R
R
AV:96
AV:97
AV:98
AV:99
AV:100
AV:101
AV:102
AV:103
CHWS
DGT
DO
EWT
—
—
—
—
LEGEND
Chilled Water Switch
EXV
Discharge Gas Thermistor
OAT
Digital Output
R
Entering Water Temperature W
—
—
—
—
UNITS
DEFAULT
VALUE
A
A
A
°F
°F
°F
psi
psi
psi
psi
psi
%
%
%
°F
°F
°F
°F
°F
°F
psi
psi
psi
%
A
A
°F
°F
°F
°F
%
%
RANGE
0-100
0 - 4000
0 - 100
V
°F
°F
0=Off
1=Running
2=Stopping
3= Delay
4=Tripout
5=Ready
6=Override
7=Defrost
8=Run Test
9=Test
°F
°F
BACNET
OBJECT NAME
curren_a_1
curren_b_1
curren_c_1
cp_tmp_a_1
cp_tmp_b_1
cp_tmp_c_1
op_a_1
op_b_1
op_c_1
dop_a_1
dop_b_1
capa_t_1
capb_t_1
capc_t_1
sct_a_1
sct_b_1
sct_c_1
sst_a_1
sst_b_1
sst_c_1
sp_a_1
sp_b_1
sp_c_1
dem_lim_1
tot_curr_1
curr_lim_1
ctrl_wt_1
ctrl_pnt_1
sp_1
oat_1
lag_lim_1
cap_t_1
sp_sel_1
capt_010_1
chwstemp_1
t_heat_c_1
heatcool_1
status_1
cool_ewt_1
t_heater_1
R
°F
cool_lwt_1
R
R
R
R
R
R
R
kW
mA
°F
mA
psi
psi
psi
cool_pwr_1
lim_anal_1
spacetmp_1
sp_reset_1
watpres1_1
watpres2_1
watpres3_1
Expansion Valve
Outdoor Air Temperature
Read
Write
174
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
Table G — Network Points List (cont)
BACNET
OBJECT ID
AV:104
AV:105
Water pressure after filter
Water flow
READ/
WRITE
R
R
AV:106
Circuit Loading Sequence
R/W
AV:107
AV:108
AV:109
AV:110
AV:111
AV:112
AV:113
AV:114
AV:115
AV:116
Compressor A Hours
Compressor A Starts
Compressor B Hours
Compressor B Starts
Compressor C Hours
Compressor C Starts
Cooler pump #1 Hours
Cooler pump #2 Hours
Machine Operating Hours
Machine Starts
R
R
R
R
R
R
R
R
R
R
POINT NAME
AV:117
Cooler Pumps Sequence
R/W
AV:118
AV:119
AV:120
AV:121
AV:122
AV:123
AV:124
AV:125
AV:126
AV:127
AV:128
AV:129
AV:130
AV:131
AV:132
AV:133
AV:134
AV:135
AV:136
Current Limit at 100%
Pump Auto Rotation Delay
Unit Off-to-On Delay
Cooling Ice Setpoint
Cooling Ramp Loading
Cooling Reset Degrees
Cooling Setpoint 1
Cooling Setpoint 2
Current Full Reset Value
Current No Reset Value
Delta T Full Reset Value
Delta T No Reset Value
OAT Full Reset Value
OAT No Reset Value
Space T Full Reset Value
Space T No Reset Value
Switch Limit Setpoint 1
Switch Limit Setpoint 2
Switch Limit Setpoint 3
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
AV:137
Alarm State
R
AV:2901
AV:2902
AV:2903
AV:2904
AV:2905
AV:9006
AV:80001
User Defined Analog 1
User Defined Analog 2
User Defined Analog 3
User Defined Analog 4
User Defined Analog 5
System Cooling Demand Level
System OAT Master
R/W
R/W
R/W
R/W
R/W
R
R
CHWS
DGT
DO
EWT
—
—
—
—
LEGEND
Chilled Water Switch
EXV
Discharge Gas Thermistor
OAT
Digital Output
R
Entering Water Temperature W
—
—
—
—
UNITS
DEFAULT
VALUE
RANGE
psi
gal/sec
0=Auto
1=A Lead
2=B Lead
3=C Lead
hr
hr
hr
hr
hr
°F
Expansion Valve
Outdoor Air Temperature
Read
Write
175
lead_cir_1
hr_cp_a_1
st_cp_a_1
hr_cp_b_1
st_cp_b_1
hr_cp_c_1
st_cp_c_1
hr_cpum1_1
hr_cpum2_1
hr_mach_1
st_mach_1
hr
A
hr
min
°F
°^F
°^F
°F
°F
mA
mA
°^F
°^F
°F
°F
°F
°F
%
%
%
BACNET
OBJECT NAME
watpres4_1
wat_flow_1
0=No Pump
1=One Pump Only
2=Two Pumps Auto
3=Pump#1 Manual
4=Pump#2 Manual
0 - 2000
24 - 3000
0
0.2 - 2.0
-30 - 30
-20 - 70
-20 - 70
0 - 20
0 - 20
0 - 25
0 - 25
14 - 125
14 - 125
14 - 125
14 - 125
0 - 100
0 - 100
0 - 100
0=Normal
1=Partial
2=Shutdown
cpumpseq_1
curr_ful_1
pump_del_1
off_on_d_1
ice_sp_1
cramp_sp_1
cr_deg_1
csp1_1
csp2_1
v_cr_fu_1
v_cr_no_1
dt_cr_fu_1
dt_cr_no_1
oatcr_fu_1
oatcr_no_1
spacr_fu_1
spacr_no_1
lim_sp1_1
lim_sp2_1
lim_sp3_1
alm_1
user_analog_1_1
user_analog_2_1
user_analog_3_1
user_analog_4_1
user_analog_5_1
cool_demand_level_1
mstr_oa_temp_1
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
Table G — Network Points List (cont)
BACNET
OBJECT ID
POINT NAME
READ/
WRITE
BV:1
Chiller Start/Stop
R/W
BV:2
Chiller Occupied?
R/W
BV:3
BV:4
BV:5
BV:6
BV:7
BV:8
BV:9
BV:10
BV:11
BV:12
BV:13
BV:14
BV:15
BV:16
BV:17
BV:18
BV:19
BV:20
BV:21
BV:22
BV:23
BV:24
BV:25
BV:26
BV:27
BV:28
BV:29
BV:30
BV:31
BV:32
BV:33
BV:34
BV:35
BV:36
BV:37
BV:38
BV:39
BV:40
BV:41
BV:42
BV:43
BV:44
BV:45
BV:46
BV:47
BV:48
BV:49
BV:50
BV:51
BV:52
Ball Valve Position
Ball Valve Position
Ball Valve Position
Compressor Output
Compressor Output
Compressor Output
DGT Cooling Solenoid
DGT Cooling Solenoid
DGT Cooling Solenoid
Fan Output DO #1
Fan Output DO #2
Fan Output DO #3
Fan Output DO #4
Fan Output DO #5
Fan Output DO #6
Fan Output DO #7
Fan Output DO #8
Fan Output DO #1
Fan Output DO #2
Fan Output DO #3
Fan Output DO #4
Fan Output DO #5
Fan Output DO #6
Fan Output DO #7
Fan Output DO #8
Fan Output DO #1
Fan Output DO #2
Fan Output DO #3
Fan Output DO #4
Fan Output DO #5
Fan Output DO #6
Fan Output DO #7
Fan Output DO #8
Free Cooling Disable
Heat Reclaim Select
Hot Gas Bypass A Output
Hot Gas Bypass B Output
Hot Gas Bypass C Output
Oil Heater Output
Oil Heater Output
Oil Heater Output
Oil Level Input
Oil Level Input
Oil Level Input
Oil Solenoid Output
Oil Solenoid Output
Oil Solenoid Output
Slide Valve 1 Output
Slide Valve 2 Output
Slide Valve 1 Output
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R/W
R/W
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
CHWS
DGT
DO
EWT
—
—
—
—
LEGEND
Chilled Water Switch
EXV
Discharge Gas Thermistor
OAT
Digital Output
R
Entering Water Temperature W
—
—
—
—
UNITS
DEFAULT
VALUE
RANGE
0 = Disable
1 = Enable
0 = No
1 = Yes
No/Yes
No/Yes
Expansion Valve
Outdoor Air Temperature
Read
Write
176
BACNET
OBJECT NAME
chil_s_s_1
chil_occ_1
iso_refa_1
iso_refb_1
iso_refc_1
comp_a_1
comp_b_1
comp_c_1
gascoola_1
gascoolb_1
gascoolc_1
fan_a1_1
fan_a2_1
fan_a3_1
fan_a4_1
fan_a5_1
fan_a6_1
fan_a7_1
fan_a8_1
fan_b1_1
fan_b2_1
fan_b3_1
fan_b4_1
fan_b5_1
fan_b6_1
fan_b7_1
fan_b8_1
fan_c1_1
fan_c2_1
fan_c3_1
fan_c4_1
fan_c5_1
fan_c6_1
fan_c7_1
fan_c8_1
fc_dsble_1
recl_sel_1
hgbp_a_1
hgbp_b_1
hgbp_c_1
oil_ht_a_1
oil_ht_b_1
oil_ht_c_1
oil_l_a_1
oil_l_b_1
oil_l_c_1
oil_sl_a_1
oil_sl_b_1
oil_sl_c_1
slid_1_a_1
slid_2_a_1
slid_1_b_1
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
Table G — Network Points List (cont)
BACNET
OBJECT ID
BV:53
BV:54
BV:55
BV:56
BV:57
BV:58
BV:59
BV:60
BV:61
BV:62
BV:63
BV:64
BV:65
BV:66
BV:67
BV:68
BV:69
BV:70
BV:71
BV:72
BV:73
BV:74
BV:75
BV:76
BV:77
BV:78
BV:79
BV:80
BV:81
BV:82
BV:83
BV:84
BV:85
BV:86
BV:87
BV:88
BV:89
BV:90
BV:91
BV:92
BV:93
BV:94
BV:95
BV:96
BV:97
BV:98
BV:99
BV:100
BV:101
BV:102
BV:103
BV:104
CHWS
DGT
DO
EWT
—
—
—
—
READ/
WRITE
R
R
R
R/W
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R/W
R
R
R/W
R/W
R
R
R/W
R/W
R
R
POINT NAME
Slide Valve 2 Output
Slide Valve 1 Output
Slide Valve 2 Output
Emergency Stop
Setpoint Occupied?
Startup Delay in Effect
Second Setpoint in Use
Reset in Effect
Demand Limit Active
Ramp Loading Active
Cooler Heater Active
Cooler Pumps Rotation
Pump Periodic Start
Night Low Noise Active
System Manager Active
Master Slave Active
Auto Changeover Active
Free Cooling Active
Reclaim Active
Boiler Active
Heating Low EWT Lockout
Condenser pumps Rotation
Ice Mode in Effect
Defrost Active on Circuit A
Defrost Active on Circuit B
Low Suction Circuit A
Low Suction Circuit B
Low Suction Circuit C
High DGT Circuit A
High DGT Circuit B
High DGT Circuit C
High Pressure Override Circuit A
High Pressure Override Circuit B
High Pressure Override Circuit C
Low Superheat Circuit A
Low Superheat Circuit B
Low Superheat Circuit C
Alarm Relay Status
Alert Relay Status
Boiler Command
Condenser Flow Status
Cooler Flow Setpoint Out
Cooler Flow Switch
Cooler Heater Command
Cooler Pump #1 Command
Cooler Pump #2 Command
Cooler Pump Run Status
Electrical Box Interlock
Ramped Loading Select
Staged Loading Sequence
System Demand Limiting
Free Cooling Disable Switch
LEGEND
Chilled Water Switch
EXV
Discharge Gas Thermistor
OAT
Digital Output
R
Entering Water Temperature W
—
—
—
—
UNITS
DEFAULT
VALUE
RANGE
0=Disable,1=Enable
0=No, 1=Yes
Off/On
Off/On
Off/On
No/Yes
No/Yes
Expansion Valve
Outdoor Air Temperature
Read
Write
177
BACNET
OBJECT NAME
slid_2_b_1
slid_1_c_1
slid_2_c_1
emstop_1
sp_occ_1
mode_01_1
mode_02_1
mode_03_1
mode_04_1
mode_05_1
mode_06_1
mode_07_1
mode_08_1
mode_09_1
mode_10_1
mode_11_1
mode_12_1
mode_13_1
mode_14_1
mode_15_1
mode_16_1
mode_17_1
mode_18_1
mode_19_1
mode_20_1
mode_21_1
mode_22_1
mode_23_1
mode_24_1
mode_25_1
mode_26_1
mode_27_1
mode_28_1
mode_29_1
mode_30_1
mode_31_1
mode_32_1
alarmout_1
alert_1
boiler_1
condflow_1
set_flow_1
flow_sw_1
coolheat_1
cpump_1_1
cpump_2_1
cpumpdef_1
elec_box_1
ramp_sel_1
seq_typ_1
dem_lmt_act_1
fc_sw_1
APPENDIX G — BACNET COMMUNICATIONS OPTION (cont)
Table G — Network Points List (cont)
BACNET
OBJECT ID
BV:105
BV:106
BV:107
BV:108
BV:109
BV:110
BV:111
BV:112
BV:113
BV:114
Ice Done Storage Switch
Limit Switch 1 Status
Limit Switch 2 Status
Occupied Override Switch
On/Off - Remote Switch
Ready or Running Status
Remote Heat/Cool Switch
Remote Interlock Status
Remote Reclaim Switch
Remote Setpoint Switch
READ/
WRITE
R
R
R
R
R
R
R
R
R
R
BV:115
Rotate Cooler Pumps?
R/W
BV:116
BV:117
BV:118
BV:119
BV:120
BV:2911
BV:2912
BV:2913
BV:2914
BV:2915
BV:2999
Running Status
Shutdown Indicator State
Current Limit Select
Local Schedule
Element Communications Alarm
User Defined Binary 1
User Defined Binary 2
User Defined Binary 3
User Defined Binary 4
User Defined Binary 5
Element Comm Status
R
R
R/W
R
R
R/W
R/W
R/W
R/W
R/W
R
CHWS
DGT
DO
EWT
—
—
—
—
POINT NAME
LEGEND
Chilled Water Switch
EXV
Discharge Gas Thermistor
OAT
Digital Output
R
Entering Water Temperature W
—
—
—
—
UNITS
DEFAULT
VALUE
RANGE
BACNET
OBJECT NAME
ice_sw_1
lim_sw1_1
lim_sw2_1
occ_ovsw_1
onoff_sw_1
ready_1
hc_sw_1
rem_lock_1
recl_sw_1
setp_sw_1
0=No
1=Yes
rotcpump_1
Off/On
Expansion Valve
Outdoor Air Temperature
Read
Write
178
running_1
shutdown_1
curr_sel_1
schedule_1
comm_lost_alm_1
user_binary_1_1
user_binary_2_1
user_binary_3_1
user_binary_4_1
user_binary_5_1
element_stat_1
INDEX
4-20 mA temperature reset 39
Actual start-up 59
Actuated ball valve (ABV) 67
Alarms and alerts 88
Alarm control 46
Equipment priority 47
Routing control 46
System name 47
BACnet communications option 168-178
Board addresses 19
Brine or glycol operation 30
Broadcast acknowledger 46
Broadcast configuration 46
Capacity control overrides 47
Carrier Comfort Network® (CCN)
Interface 20
Loadshed controlled demand limit 46
Tables 142-156
Chilled water flow switch 84
Chilled water fluid type selection 28
Circuit/compressor staging
and loading 31
Loading 32
Staging 31
Communication failure retry time 47
Compressor
Assembly 77
Oil system 78
Protection 87
Compressor protection
module (CPM) 9
Condenser coil maintenance
and cleaning recommendations 85
Condenser fans 86
Configuration 21-59
Control module communication 19
Controls 8-21
Conventions used in this manual 3
Cooler
Protection 87
Pump control 30
Cooling set point selection 27
CPM DIP switch addresses 157-160
Daylight saving time configuration 47
Demand limit 42
Externally powered capacity based 43
Externally powered current based 43
Switch controlled 42
Diagnostic alarm codes
and possible causes 88
Display module usage 3
Dual chiller control 32
For parallel applications 33
For series applications 36
Pump control for parallel
chiller applications 36
Pump control for series
chiller applications 37
Dual chiller sequence of operation 68
Dual pump and manual control 31
DX cooler units 82
Economizer assembly 74
Electronic expansion valve (EXV) 74
EXV board 9
Economizer EXV control 76
Main EXV control 74,75
Troubleshooting procedure 76
Emergency on/off switch (SW2) 17
Enable-off-remote contact
switch (SW1) 17
Energy Management Module (EMM) 17
Fan boards 15
Flooded cooler units 79
Flow rate requirements 60
Fluid set point control location 27
Freeze protection 80,82
Fresh water 28
General (Controls) 8
Green LED 19
Head pressure control 50
Heat exchangers, inspecting/cleaning 82
Hot gas bypass/pump board 17
Ice storage operation 46
Leak testing 86
Liquid fluid temperature 82
Local equipment network 19
Loss of fluid flow protection 81,82
Low ambient temperature
head pressure control 50
Operating instructions 50
Option 50
Low fluid temperature 80
Machine control methods 22
Machine on/off control 22
Machine start delay 31
Main Base Board (MBB) 8
Maintenance 87,88
Log Sheets 165-167
Microchannel heat exchanger
maintenance and cleaning 85
Minimum fluid loop volume 60
Minimum load control 32
Navigator™ display module 7
Display tables 128-141
Machine control 25
Night time/low noise applications 37
No pump control 30
OAT broadcast 46
Oil separator heaters 87
Operating limitations 60
Operating modes 68
Operation 67-74
Outside air temperature reset 39
Piping and instrumentation 161-164
Pressure relief valves 87
Pre-start-up 59
Pump operation 68
Ramp loading 38
Re-alarm time 47
Recommended maintenance schedule 87
Red LED 19
Refrigerant charge 86
Refrigerant circuit 86
Relief devices 87
Remote alarm and alert relays 20
Retubing 81,83
Return water reset 38
Round table plate fin condenser coil
maintenance and cleaning
85
Safety considerations 2,3
Safety devices 87
Sensors 71
Sequence of operation 67
Service 74-87
Service test 104
Set point occupancy 27
Single pump control 30
Space temperature reset 39
Start-up 59-67
Start-up checklist for
30XA liquid chillers CL-1 to CL-8
Suction service valve 79,82
System check 59
Temperature reset 38
Thermistors 70
Tightening cooler head bolts 81,84
179
Touch Pilot display 3,19
Display tables 110-127
Machine control 22
Operation configuration tables
Transducers 71
Troubleshooting 88-109
Tube plugging 81,82
Voltage 60
Water treatment 82
Winter shutdown, preparation for
Yellow LED 19
21
84
Copyright 2011 Carrier Corporation
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53300091-01
Printed in U.S.A.
Form 30XA-4T
Pg 180
612
10-11
Replaces: 30XA-3T
START-UP CHECKLIST FOR 30XA LIQUID CHILLERS
A. PROJECT INFORMATION
Job Name ______________________________________
Address ________________________________________
City __________________ State ________ Zip ________
Installing Contractor_______________________________
Sales Office _____________________________________
Start-up Performed By _____________________________
Design Information
CAPACITY
EWT
LWT
FLUID TYPE
FLOW RATE
P.D.
AMBIENT
Cooler
Unit
Model _______________________________________ Serial ______________________________________
Compressors
Compressor A
Model _______________________________________ Serial ______________________________________
Compressor B
Model _______________________________________ Serial ______________________________________
Compressor C
Model _______________________________________ Serial ______________________________________
Cooler
Model _______________________________________ Serial ______________________________________
B. PRELIMINARY EQUIPMENT CHECK (This section to be completed by installing contractor)
1. Is there any physical damage?
 Yes
 No
Will this prevent start-up?
 Yes
 No
Description
__________________________________________________________________________________________
2. Unit is installed level as per the installation instructions.
 Yes
 No
3. Power supply agrees with the unit nameplate.
 Yes
 No
4. Correct control voltage ________vac.
 Yes
 No
5. Electrical power wiring is installed properly.
 Yes
 No
6. Unit is properly grounded.
 Yes
 No
7. Electrical circuit protection has been sized and installed properly.
 Yes
 No
8. All terminals are tight.
 Yes
 No
9. All plug assemblies are tight.
 Yes
 No
10. All cables, thermistors and transducers have been inspected for cross wires.
 Yes
 No
11. All thermistors are fully inserted into wells.
 Yes
 No
12. Oil separator heaters energized for 24 hours before start-up.
 Yes
 No
13. Relief valve vent piping per local codes.
 Yes
 No
Chilled Water System Check
1.
2.
3.
4.
5.
6.
7.
8.
All chilled water valves are open.
All piping is connected properly.
All air has been purged from the system.
Chilled water pump is operating with the correct rotation.
Chilled water pump starter controlled by chiller.
Chilled water flow switch operational.
Inlet piping to cooler includes a 20 mesh strainer.
Water loop volume greater than 3 gal/ton (40 L/kW) for air conditioning
or 6 gal/ton (80 L/kW) for process cooling and low ambient operation.
9. Proper loop freeze protection provided to ____ F (C).
Antifreeze type__________________ Concentration _____%.
(If antifreeze solution is not utilized on 30XA machines and the
minimum outdoor ambient is below 32 F (0 C) then items 10 and 11
have to be completed to provide cooler freeze protection to –20 F (–28.9 C).
Refer to Installation Instructions for proper cooler winterization procedure.)
10. Outdoor piping wrapped with electric heater tape.
11. Cooler heaters installed and operational.
12. Is the Unit equipped with low ambient head pressure control?
a. If yes, are wind baffles installed?







Yes
Yes
Yes
Yes
Yes
Yes
Yes







No
No
No
No
No
No
No
 Yes
 No
 Yes
 No








Yes
Yes
Yes
Yes
No
No
No
No
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53300091-01
Printed in U.S.A.
Form 30XA-4T
Pg CL-1
612
10-11
Replaces: 30XA-3T
1.
2.
3.
4.
5.
6.
7.
All liquid line service valves are open.
Verify actuated ball valve (ABV) operation. (Flooded Cooler Units only)
All suction and discharge service valves are open.
Economizer service valves open. (Leaving Main EXV and Leaving BPH)
Oil service valves open.
Leak check unit. Locate, repair and report any refrigerant leaks.
Voltage at terminal block is within unit nameplate range.
Check voltage imbalance: A-B______ A-C______B-C______
Average voltage = __________ (A-B + A-C + B-C)/3
Maximum deviation from average voltage = _______
Voltage imbalance = ______% (max. deviation / average voltage) X 100
Is voltage imbalance less than 2%.
(DO NOT start chiller if voltage imbalance is greater than 2%.
Contact local utility for assistance.)
8. Verify cooler flow rate
Pressure entering cooler
_____ psig (kPa)
Pressure leaving cooler
_____ psig (kPa)
Cooler pressure drop
_____ psig (kPa)
Psig x 2.31 ft./psi =
_____ ft of water
kPa x 0.334 m/psi =
_____ mm of water
Cooler flow rate _____ gpm (l/s) (See Cooler Pressure Drop Curve)














Yes
Yes
Yes
Yes
Yes
Yes
Yes
 Yes
No
No
No
No
No
No
No
 No
Start and Operate Machine
1.
2.
3.
4.
5.
6.
Complete component test utilizing Quick Test Mode
Operate compressors and verify slide valve operation using manual test mode.
Check refrigerant and oil charge. Record charge information.
Record compressor and condenser fan motor current.
Record operating data.
Provide operating instructions to owner’s personnel.
Circuit A
Circuit B
Circuit C
Refrigerant Charge
Additional charge required
__________
___________
___________
__________
___________
___________
Oil Charge
Additional charge required
Record Software Versions
TOUCH PILOT
DESRIPTION
Software Part Number
NAVIGATOR ITEM
NAVIGATOR SUB-MODE
ITEM EXPANSION
APPL
Run StatusVERS
CSA-SR- __ __ __ __ __ __
(Press ENTER and ESCAPE simultaneously to obtain software versions)
CL-2
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - CUT ALONG DOTTED LINE
CUT ALONG DOTTED LINE
C. UNIT START-UP
Record Configuration Information
TOUCH PILOT™ DESCRIPTION
NAVIGATOR™
ITEM
TEST
NAVIGATOR
SUBMODE
ConfigurationDISP
Metric Display on STDU
METR
ConfigurationDISP
US
Language Selection
LANG
ConfigurationDISP
English
None (Navigator Configuration)
DEFAULT*
OFF
Unit Type
TYPE
ConfigurationUNIT
Air-Cooled
Unit Capacity Model
TONS
ConfigurationUNIT
Nominal Unit Size
NB Fans on Varifan Cir A
VAR.A
ConfigurationUNIT
0: No low ambient temperature
head pressure control
1: low ambient temperature
head pressure control installed
NB Fans on Varifan Cir B
VAR.B
ConfigurationUNIT
0: No low ambient temperature
head pressure control
1: low ambient temperature
head pressure control installed
NB Fans on Varifan Cir C
VAR.C
ConfigurationUNIT
0: No low ambient temperature
head pressure control
1: low ambient temperature
head pressure control installed
Nameplate voltage
Power Supply Voltage
VOLT
ConfigurationUNIT
Power Frequency 60HZ Sel
60HZ
ConfigurationUNIT
YES
Soft Starter Select
STAR
ConfigurationUNIT
NO†
Y.D
ConfigurationUNIT
Unit Dependent
Must Trip Amps (Circuit A)
Wye Delta Start Select
MTA.A
ConfigurationUNIT
Unit Dependent
Must Trip Amps (Read Circuit A)
R.MT.A
ConfigurationUNIT
Unit Dependent
Must Trip Amps (Circuit B)
MTA.B
ConfigurationUNIT
Unit Dependent
Must Trip Amps (Read Circuit B)
R.MT.B
ConfigurationUNIT
Unit Dependent
Must Trip Amps (Circuit C)
MTA.C
ConfigurationUNIT
Unit Dependent
Must Trip Amps (Read Circuit C)
R.MT.C
ConfigurationUNIT
Unit Dependent
S1 Config Switch (Circuit A)
C.SW.A
ConfigurationUNIT
Unit Dependent
S1 Config Switch
(Read Circuit A)
R.CSA
ConfigurationUNIT
Unit Dependent
S1 Config Switch (Circuit B)
C.SW.B
ConfigurationUNIT
Unit Dependent
S1 Config Switch
(Read Circuit B)
R.CSB
ConfigurationUNIT
Unit Dependent
S1 Config Switch (Circuit C)
C.SW.C
ConfigurationUNIT
Unit Dependent
S1 Config Switch
(Read Circuit C)
R.CSC
ConfigurationUNIT
Unit Dependent
Air Cooled Reclaim Sel
RECL
ConfigurationUNIT
NO†
DX Cooler Select
DX.CL
ConfigurationUNIT
NO
Energy Management Module
EMM
ConfigurationUNIT
NO
Password Enable
PAS.E
ConfigurationUNIT
ENBL
0111
Factory Password
PASS
ConfigurationUNIT
Cooler Heater Select
CO.HT
ConfigurationUNIT
1
Condenser Water Val Sel
CON.V
ConfigurationUNIT
NO†
Hot Gas Bypass Select
HGBP
ConfigurationUNIT
NO
MCHX Exchanger Select
MCHX
ConfigurationUNIT
NO
HI.TI
ConfigurationUNIT
NO
NO†
High Tier Display Selec
Hydronic Kit Select
H.KIT
ConfigurationUNIT
Cooler Pass Number
PA.NB
ConfigurationUNIT
2
VLT Fan Drive Select
VLT
ConfigurationUNIT
NONE†
VLT Fan Drive RPM
RPM
ConfigurationUNIT
0†
H.CON
ConfigurationUNIT
NO†
Cooler Fluid Type
FLUD
ConfigurationSERV
WATER
WATER†
High Condensing Select
Condenser Fluid Type
CFLU
ConfigurationSERV
EXV MOP Setpoint
MOP
ConfigurationSERV
62
High Pressure Threshold
HP.TH
ConfigurationSERV
290.0
* Based on Navigator controls.
† Not supported.
CL-3
ENTRY
TOUCH PILOT™ DESCRIPTION
NAVIGATOR™
ITEM
NAVIGATOR
SUBMODE
DEFAULT*
EXV A Superheat Setpoint
SHP.A
ConfigurationSERV
Unit dependent
EXV B Superheat Setpoint
SHP.B
ConfigurationSERV
Unit dependent
EXV C Superheat Setpoint
SHP.C
ConfigurationSERV
Unit dependent
HTR
ConfigurationSERV
2.0 (Number of
degrees
added to brine
freeze
set point to enable
cooler heater.)
Cooler Heater Delta Spt
Entering Fluid Control
EWTO
ConfigurationSERV
NO
Auto Start When SM Lost
AU.SM
ConfigurationSERV
NO
Brine Freeze Setpoint
LOSP
ConfigurationSERV
34
Brine Flow Switch SP
FL.SP
ConfigurationSERV
1†
Varifan Proportional Gain
HD.PG
ConfigurationSERV
2.0
Varifan Derivative Gain
HD.DG
ConfigurationSERV
0.4
Varifan Integral Gain
HD.IG
ConfigurationSERV
0.2
Element
CCNA
ConfigurationOPTN
1
Bus
CCNB
ConfigurationOPTN
0
Baud Rate
BAUD
ConfigurationOPTN
9600
Circuit Loading Sequence
LOAD
ConfigurationOPTN
EQUAL
Staged Loading Sequence
LLCS
ConfigurationOPTN
AUTOMATIC
Ramp Loading Select
RL.S
ConfigurationOPTN
DSBL
Unit Off to On Delay
DELY
ConfigurationOPTN
1
Ice Mode Enable
ICE.M
ConfigurationOPTN
DSBL
Condenser Pumps Sequence†
HPUM
ConfigurationOPTN
NO PUMP
Cooler Pumps Sequence
PUMP
ConfigurationOPTN
NO PUMP
Pump Auto Rotation Delay
ROT.P
ConfigurationOPTN
48
Pump Sticking Protection
PM.PS
ConfigurationOPTN
NO
NO
Stop Pump During Standby
P.SBY
ConfigurationOPTN
Flow Checked if C Pump On
P.LOC
ConfigurationOPTN
NO
Start Hour (Night Control)
LS.ST
ConfigurationOPTN
00.00
End Hour (Night Control)
LS.ND
ConfigurationOPTN
00.00
Capacity Limit (Night Control)
LS.LT
ConfigurationOPTN
100
Reverse Alarms Relay
RV.AL
ConfigurationOPTN
NO
Heating OAT Threshold*
OA.TH
ConfigurationOPTN
5F
Current Limit Select
CUR.S
ConfigurationOPTN
NO
Current Limit at 100%
CUR.F
ConfigurationOPTN
2000
Cooling Reset Select
CRST
ConfigurationRSET
NO RESET
Heating Reset Select
HRST
ConfigurationRSET
NO RESET
Demand Limit Type Select
DMDC
ConfigurationRSET
NONE
mA for 100% Demand Limit
DMMX
ConfigurationRSET
0.0
mA for 0% Demand Limit
DMZE
ConfigurationRSET
10.0
Master/Slave Select
MSSL
ConfigurationRSET
DISABLE
Slave Address
SLVA
ConfigurationRSET
2
Lead/Lag Select
LLBL
ConfigurationRSET
ALWAYS LEAD
Lead/Lag Balance Delta
LLBD
ConfigurationRSET
168
Lag Start Timer
LLDY
ConfigurationRSET
10
Start if Error Higher
LL.ER
ConfigurationRSET
4
Lag Minimum Running Time
LAG.M
ConfigurationRSET
0
Lag Unit Pump Control
LAGP
ConfigurationRSET
OFF IF U STP
Lead Pulldown Time
LPUL
ConfigurationRSET
0
Chiller in Series
SERI
ConfigurationRSET
NO
* Based on Navigator controls.
† Not supported.
CL-4
ENTRY
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - CUT ALONG DOTTED LINE
CUT ALONG DOTTED LINE
Record Configuration Information
Record Configuration Information
TOUCH PILOT™ DESCRIPTION
Cooling Setpoint 1
Cooling Setpoint 2
Cooling Ice Setpoint
Current No Reset Value (Cooling)
Current Full Reset Value (Cooling)
Delta T No Reset Value (Cooling)
Delta T Full Reset Value (Cooling)
OAT No Reset Value (Cooling)
OAT Full Reset Value (Cooling)
Space T No Reset Value
Space T Full Reset Value
Cooling Reset Deg. Value
Cool Changeover Setpoint
Cooling Ramp Loading
Switch Limit Setpoint 1
Switch Limit Setpoint 2
Switch Limit Setpoint 3
Water Val Condensing Stp*
Equipment Start (I/O Button)
Setpoint Select
Heal/Cool Select
NAVIGATOR™
ITEM
CSP.1
CSP.2
CSP.3
CRV1
CRV2
CRT1
CRT2
CRO1
CRO2
CRS1
CRS2
DGRC
CAUT
CRMP
DLS1
DLS2
DLS3
W.SCT
OPER
SP.SE
HC.SE
NAVIGATOR
SUBMODE
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointCOOL
Set PointMISC
Set PointMISC
Set PointMISC
Set PointMISC
Operating ModesSLCT
Operating ModesSLCT
Operating ModesSLCT
*Not supported.
CL-5
DEFAULT
44.0
44.0
44.0
0
0
0
0
14.0
14.0
14.0
14.0
0
75
1.0
100
100
100
95.0
SWITCH CTRL
SET POINT OOC
COOLING
ENTRY
TOUCH PILOT™ DESCRIPTION
Service Test Enable
Compressor A Output
Slide Valve Capacity A
Compressor B Output
Slide Valve Capacity B
Compressor C Output
Slide Valve Capacity C
Quick Test Enable
Circuit A EXV Position
Circuit B EXV Position
Circuit C EXV Position
Cir A Economizer EXV Position
Cir B Economizer EXV Position
Cir C Economizer EXV Position
Circuit A Fan Stages
Circuit B Fan Stages
Circuit C Fan Stages
Circuit A Head Pressure Speed
Circuit B Head Pressure Speed
Circuit C Head Pressure Speed
Circuit A Oil Heater
Circuit A Slide Valve 1
Circuit A Slide Valve 2
Circuit A Hot Gas Bypass
Circuit A Oil Solenoid
Circuit A DGT Cool Solenoid
Circuit B Oil Heater
Circuit B Slide Valve 1
Circuit B Slide Valve 2
Circuit B Hot Gas Bypass
Circuit B Oil Solenoid
Circuit B DGT Cool Solenoid
Circuit C Oil Heater
Circuit C Slide Valve 1
Circuit C Slide Valve 2
Circuit C Hot Gas Bypass
Circuit C Oil Solenoid
Water Exchanger Pump 1
Water Exchanger Pump 2
Cooler Heater Output
Cir A Heater Ball Valve
Cir B Heater Ball Valve
Cir C Heater Ball Valve
Chiller Ready Status
Chiller Running Output
Customer Shutdown Out
Chiller Capacity in 0-10V
Alarm Relay Output
Alert Relay Output
NAVIGATOR™ ITEM
T.REQ
CP.A
SLI.A
CP.B
SLI.B
CP.C
SLI.C
Q.REQ
EXV.A
EXV.B
EXV.C
ECO.A
ECO.B
ECO.C
FAN.A
FAN.B
FAN.C
SPD.A
SPD.B
SPD.C
HT.A
SL1.A
SL2.A
HGP.A
OLS.A
DGT.A
HT.B
SL1.B
SL2.B
HGP.B
OLS.B
DGT.B
HT.C
SL1.C
SL2.C
HGP.C
OLS.C
PMP.1
PMP.2
CL.HT
BVL.A
BVL.B
BVL.C
Q.RDY
Q.RUN
SHUT
CATO
ALRM
ALRT
CL-6
NAVIGATOR SUBMODE
Service TestTEST
Service TestTEST
Service TestTEST
Service TestTEST
Service TestTEST
Service TestTEST
Service TestTEST
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
Service TestQUIC
CHECK WHEN COMPLETE
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - CUT ALONG DOTTED LINE
CUT ALONG DOTTED LINE
Component Test — Complete the following tests to make sure all peripheral components are
operational before the compressors are started.
Operating Data:
Record the following information from the Run Status, Temperatures and Outputs Modes when machine is in a
stable operating condition.
TEMPERATURES
COOLER ENTERING FLUID
COOLER LEAVING FLUID
CONTROL POINT
CAPACITY
OUTSIDE AIR TEMPERATURE
LEAD/LAG LEAVING FLUID
EWT _______________
LWT _______________
CTPT _______________
CAP _______________
OAT _______________
CHWS_______________ (Dual Chiller Control Only)
CIRCUIT A
CIRCUIT B
SCT.A __________
SCT.B __________
SST.A __________
SST.B __________
DGT.A __________
DGT.B __________
SGT.A __________
SGT.B __________
SUP.A __________
SUP.B __________
ECT.A __________
ECT.B __________
ESH.A __________
ESH.B __________
CTP.A __________
CTP.B __________
EXV.A__________
EXV.B __________
ECO.A__________
ECO.B __________
NOTE: EXV A,B,C positions are found in the output mode.
COMPRESSOR MOTOR CURRENT
L1
L2
COMPRESSOR A1
______
______
COMPRESSOR B1
______
______
COMPRESSOR C1
______
______
L3
______
______
______
CONDENSER FAN MOTOR CURRENT
L1
L2
FAN MOTOR 1
______
______
FAN MOTOR 2
______
______
FAN MOTOR 3
______
______
FAN MOTOR 4
______
______
FAN MOTOR 5
______
______
FAN MOTOR 6
______
______
FAN MOTOR 7
______
______
FAN MOTOR 8
______
______
FAN MOTOR 9
______
______
FAN MOTOR 10
______
______
FAN MOTOR 11
______
______
FAN MOTOR 12
______
______
FAN MOTOR 13
______
______
FAN MOTOR 14
______
______
FAN MOTOR 15
______
______
FAN MOTOR 16
______
______
FAN MOTOR 17
______
______
FAN MOTOR 18
______
______
FAN MOTOR 19
______
______
FAN MOTOR 20
______
______
FAN MOTOR 21
______
______
FAN MOTOR 22
______
______
L3
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
CIRCUIT C
SCT.C___________
SST.C ___________
DGT.C ___________
SGT.C ___________
SUP.C ___________
ECT.C ___________
ESH.C ___________
CTP.C ___________
EXV.C ___________
ECO.C ___________
CL-7
SIGNATURES:
Start-up
Technician _____________________________________
Date ________________________________________________
Customer
Representative __________________________________
Date ________________________________________________
Copyright 2011 Carrier Corporation
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53300091-01
Printed in U.S.A.
Form 30XA-4T
Pg CL-8
612 10-11
Replaces: 30XA-3T
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - CUT ALONG DOTTED LINE
CUT ALONG DOTTED LINE
COMMENTS:
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________