Sharp LL-153A Service manual

15” LCD Color Monitor
Sharp LL-153A
Service
Service
Service
Horizontal Frequency
30kHz –80kHz
TABLE OF CONTENTS
Description
Page
Description
Page
Table Of Contents.......……..……..........................…........1 6. Schematic……………....................................…17
Revision List.….............……..........................……......2 6.1 Main Board.……...……..........................................17
Important Safety Notice.…………....................……......3 6.2 Inverter Board..………..……..................................22
1. Monitor Specification..............................………........4 6.3 Adapter Board...………..…….................................23
2. LCD Monitor Description…………………………….......5 6.4 Audio Board...………....…….................................24
3. Operation Instruction…………...............……...........6 7. PCB Layout..…….………….......................................25
3.1 General Instructions...........................…...........6 7.1 Main Board…………….........................................25
3.2 Control Button…………….…..............……...............6 7.2 PWPC Board…..………....................................26
3.3 Adjusting the Picture...........................…............7 7.3 Audio Board……….……….....................................27
4. Input/Output Specification............………..……............8 7.4 Key Board……………….....................................28
4.1 Input Signal Connector............………….................8 8. Maintainability……….......................................28
4.2 Factory Preset Display Modes..........................9 8.1 Equipments and Tools Requirement……..............28
4.3 Power Supply……..………………………….………….10
N
8.2 Trouble Shooting…….………..............................29
4.4 Panel Specification.....………………………................10 9. White-Balance, Luminance adjustment.............34
5. Block Diagram……...................…………................13 10. Monitor Exploded View……….……………............36
5.1 Soft Flow Chart….………………..……..……....….......13 11. BOM List……….....................................................37
5.2 Electrical Block Diagram….……………..…........….….15
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
1
15” LCD Color Monitor
Sharp LL-153A
Revision List
Revision
Date
Revision History
TPV Model
A00
Dec-28-06
Initial Release
T56CM5NJXXXWAJ
2
15” LCD Color Monitor
Important Safety Notice
Sharp LL-153A
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiation when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)
3
15” LCD Color Monitor
Sharp LL-153A
1. Monitor Specifications
Items
Descriptions
Driving system
TFT Color LCD
Type
CPT CLAA150XP01Q
Size
38cm(15.0")
Pixel pitch
0.297mm(H) x 0.297mm(V)
Viewable angle
140˚ (H) 125˚ (V)
Response time (type)
8 ms for CPT panel
Video
R, G, B Analog input
Digital input
Sync. Type
H/V TTL
H-Frequency
24.8kHz – 80kHz
V-Frequency
56-75Hz
ON Mode
≤27W
OFF Mode
≤1W
LCD Panel
Input
Power Consumption
Contrast Ratio
500:1
Dot Clock
135MHz
White Luminance
250cd/m2
Max. Resolution
1024 × 768 @75Hz
Power Consumption
(Maximum)
27 Watts
Display Color
16 M (6-bits+FRC)
Plug & Play
VESA DDC2BTM
Input Connector
15-pin D-Sub
Maximum Screen Size
Horizontal: 304.1mm;Vertical: 228.1mm
Power Source
100~240VAC,47~63Hz
Environmental
Considerations
Operating Temp: 5°C to 35°C
Storage Temp: -20°C to 60°C
Operating Humidity: 10% to 85%
4
15” LCD Color Monitor
Sharp LL-153A
2. LCD Monitor Description
The LCD MONITOR will contain a main board, a power board and a keypad board which house the flat panel control
logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Monitor Block Diagram
Flat Panel and
CCFL Drive.
CCFL backlight
PWPC board
main board
(Include: adapter, inverter)
RS232 Connector
For white balance
adjustment in factory
mode
Keyboard
AC-IN
HOST Computer
100V-240V
5
Video signal, DDC
15” LCD Color Monitor
Sharp LL-153A
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator will light up.
3.2 Control Buttons
- Power Button:
When pressed, the monitor enters the off mode, and the LED turns blank. Press again to restore normal status.
-
Left / Right Button:
The Left/Right Button is used to control the monitor functions. Press to switch functions or adjust settings.
-
/MODE:
The
/MODE Key is used to move the cursor and select display mode.
-
Power Indicator:
Green — Power On mode.
Red
— Power Saving mode.
Blank
—Power Off Mode.
LED = GREEN, BLINKING (0.5s period) —Out of Range
OSD Menu
Volume/Bright +, & Menu Select
Move the Cursor and
Select Display Mode
NO.
Name
1
MENU
2
/MODE
3
<
4
>
5
POWER
6
Indicator Light
Indicator Light
Power On/Off
Within OSD
An adjustment menu display, a change,
elimination
Without OSD
Activate OSD main menu
Select display mode to STD or
OFFICE or sRGB or VIVID.
1.Move the cursor to left
Activate the volume and the bright
2. Decrease the value of the selected item menu
1.Move the cursor to right
Activate the volume and the
2.Increase the value of the selected item brightness menu
Move the cursor to down
Power On / Off
Green—On
Power On / Off
Red—Save
6
Green—On
Red—Save
15” LCD Color Monitor
Sharp LL-153A
3.3 Adjusting the Picture
1. Press the MENU-button to activate the OSD window.
2. Press < or > to select the desired function.
3. Press the
/ MODE -button to select the function that you want to adjust.
4. Press < or > to change the settings of the current function.
5. To exit and save, select the exit function, or leave the monitor alone for 10 seconds. If you want to adjust any
other function, repeat steps 2-4.
CONTROL FUNCTION
Main Menu
Sub Main Menu
Description
Adjust picture Clock to reduce
Vertical-Line noise.
Adjust Picture Phase to reduce
Horizontal-Line noise.
Adjust the horizontal position of the
picture.
Adjust the vertical position of the
picture.
Clock
Phase
H. Position
V. Position
Black Level
Adjust the black level of the picture.
Contrast
Contrast from Digital-register.
Cool
Recall cool Color Temperature from
EEPROM.
STD
Recall standard Color Temperature
from EEPROM.
Warm
Recall warm Color Temperature
from EEPROM.
White Balance
User
OSD H-Position
OSD V-Position
Scaling
7
Adjust the value of the
Red/Green/Blue user color
temperature.
Adjust the horizontal position of the
OSD.
Adjust the vertical position of the
OSD.
Adjust the sharpness of the
pictures.
English
Set OSD display language to
English.
Español
Set OSD display language to
Spaish.
Français
Set OSD display language to
French.
中文
Set OSD display language to
Chinese.
日本语
Set OSD display language to
Japanese.
15” LCD Color Monitor
Sharp LL-153A
Information
Show the model, the S/N and the
Usage time.
Off
The off timer is off
On
The off timer is on
4. Input/Output Specification
4.1 Input Signal Connector
D-SUB connector
Pin No.
Description
Pin No.
Description
1.
Red Video
9.
+5V Supply
2.
Green Video
10.
GND
3.
Blue Video
11.
NC
4.
NC
12.
DDC-Serial Data
5.
GND
13.
H-Sync
6.
Red Ground
14.
V-Sync
7.
Green Ground
15.
DDC-Serial Clock
8.
Blue ground
Analog Connector
1
5
6
10
11
15
8
15” LCD Color Monitor
Sharp LL-153A
4.2 Factory Preset Display Modes
4.3 Power Supply
The power supply should be integrated to the monitor housing.
A/C Line voltage range
: 100 V ~ 240 V
A/C Line frequency range
: 50 ± 3Hz, 60 ± 3Hz
Current
: 1.5A max at 100V; 0.8A max at 240 V
Peak surge current
: < 55A peak at 240 VAC and cold starting
Leakage current
: < 3.5mA
Power line surge
: No advance effects (no loss of information or defect)
With a maximum of 1 half-wave missing per second
DC output Voltage
Current
: 5VDC ± 5%; 12VDC± 5%
1.5Amp (5V) ;2 Amp (12V)
9
15” LCD Color Monitor
Sharp LL-153A
4.4 Panel Specification
4.4.1 Display Characteristics
10
15” LCD Color Monitor
Sharp LL-153A
4.4.2 Optical Characteristics
4.4.3 Electrical Characteristics
TFT LCD Module
11
15” LCD Color Monitor
Sharp LL-153A
Back- Light Unit
12
15” LCD Color Monitor
Sharp LL-153A
5. Block Diagram
5.1 Soft Flow Chart
1
Y
2
3
N
4
N
5
Y
6
N
7
8
Y
9
N
10
11
Y
N
12
13
Y
Y
14
15
Y
17
18
N
N
19
Y
13
N
16
15” LCD Color Monitor
Sharp LL-153A
1) MCU initializes.
2) Is the EPROM blank?
3) Program the EPROM by default values.
4) Get the PWM value of brightness from EPROM.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EPROM.
Turn on the LED and set it to green color.
Scalar initializes.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappears.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
14
15” LCD Color Monitor
Sharp LL-153A
5.2 Electrical Block Diagram
5.2.1 Main Board
LCD Interface
Flash memory
Scalar TSUM13AK
(Include:ADC,OSD,MCU etc.)
EPR_SDA
EPR_SCL
OSD Control
Interface
(Key pad)
RXD
TXD
RGB
H-SYNC
V-SYNC
D-Sub
Connector
EEPROM
24C16
DB15_SDA
DB15_SCL
EEPROM
24C02
15
Crystal
14.31818MHz
15” LCD Color Monitor
Sharp LL-153A
5.2.2 Inverter/Power Board
AC input
Bridge
Rectifier
and Filter
EMI filter
Rectifier
diodes
Transformer
12V
Start Circuit: R909、R910、R931
CN902
12V
Feedback
Over
Voltage
Protect
PWM
Control IC
5V
Circuit
ON/OFF
Output
Lamp
MOSFET
Q805
Transformer
Circuit
PWM
Feedback
Circuit
PWM
Control IC
ON/OFF Control
DIM
16
15” LCD Color Monitor
Sharp LL-153A
6. Schematic
6.1 Main Board
TSUM13AK
XGA/SXGA
B3
SCHEMATIC
LVDS OUTPUT
B4
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSY NC
VSY NC
DDCA_SDA
DDCA_SCL
DET_VGA
+5V
+5V
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSY NC
VSY NC
DDCA_SDA
DDCA_SCL
DET_VGA
VCC1.8
+3V3
+5V
+12V
VCC1.8
DDC_WP
DDC_WP
+3V3
+5V
+12V
3.INPUT
B5
PA[0..7]
PA[0..7]
PA[0..7]
+3V3
PA[12..13]
PA[12..13]
PA[12..13]
+12V
PB[12..21]
PB[12..21]
PB[12..21]
+3V3
VLCD
VCC1.8
+5V
VLCD
B2
on_BACKLIGHT
on_Panel
+3V3
on_BACKLIGHT
on_Panel
+12V
5.PANEL INTERFACE
VCC1.8
+5V
Adj_BACKLIGHT
+3V3
Adj_BACKLIGHT
VLCD
VLCD
Title
4.SCALER
TSUM13AK
Size
B
2.POWER
Date:
17
Document Number
Rev
A
TOP
Monday , May 30, 2005
Sheet
1
of
5
15” LCD Color Monitor
Sharp LL-153A
+3V3
+3V3
+5V
Q602
AO3401L
(3,4,5)
AIC1084-18PM
TO-263
layout together
L602
22uH
3
2
PGATE
C610
+
D602
1
C604
100uF/25V 0.1uF
C609
220uF/25V
+
U601
LM3485
7
C613
0.001uF
6
5
VIN
PGATE
VIN
VOUT
VCC1.8
(4)
ADJ
C602
47uF/25V
+
47uF/25V
C603
0.1uF
3
N.C
2
PWGND AGND
ADJ
1
+
2
C614
0.001uF
4
FB
C601
C612
0.001uF
SSM54
8
R606
33K 1/16W
R605
22 1/16W
VCC1.8
U602
3
R607
1
ISENSE
C611
0.001uF
33K 1/16W 1%
R608
20K 1/16W
keep shorter
keep away from L602
+5V
+12V
+12V
C706
0.1uF
100uF/25V
5V
+5V
FUSE_1.5A
GND
(4)
CN701
1
3
5
7
9
11
10K 1/16W
BL_ON
BL_ADJ
+12V
GND
5V
GND
2
4
6
8
10
12
R710
C711
0.1uF
F602
C709
C710
+
0.1uF
100uF/25V
R711
(3,4)
+5V
TO-263
10K 1/16W
R712
4.7K 1/16W
U702
on_BACKLIGHT (4)
3
Q703
PMBS3904
1
CONN
+3V3
C702
+5V
+
NC
R701
C713
VIN
PANEL3.3
VOUT
2
ADJ
NC
NC
C712
C714
+
NC
NC
+3V3
+5V
1K 1/16W
R703
NC
NC
R706 NC
R705 4.7K 1/16W
+3V3
R715
R702
0 1/16W
Q701
(4) Adj_BACKLIGHT
R707
1K 1/16W
PMBS3904
NC
VLCD
PANEL3.3
VLCD
C708
1uF/25V
R716
NC
R717
R714
4.7K 1/16W
10K 1/16W
R731
1K 1/16W
+3V3
(5)
C701
NC
Q704
AO3401L
R723 51K 1/16W
FB414
NC
FB413
120 OHM
3
120 OHM
FB701
GND
GND
+12V
GND
+5V
(4)
on_Panel
R725
NC
1
C718
NC
Q706
NC
2
(3,4)
C707
+
+5V
R708
C715
NC
+
C717
47uF/25V
Title
TSUM13AK
Size
B
Date:
18
Document Number
Rev
A
POWER
Wednesday , June 01, 2005
Sheet
2
of
5
Sharp LL-153A
CN405
RED+
REDGREEN+
GREENBLUE+
BLUE-
75 1/16W
R440
75 1/16W
R438
VGA_CON
56 1/16W
C432 0.047uF
R435
56 1/16W
C433 0.047uF
R436
56 1/16W
C434 0.047uF
R437
470 1/16W
C435 0.001uF
R441
100 1/16W
C436 0.047uF
R442
100 1/16W
C437 0.047uF
R443
100 1/16W
C438 0.047uF
D404
BAV99
RIN
(4)
GIN
(4)
BIN
(4)
SOG
(4)
GNDR
(4)
GNDG
(4)
GNDB
(4)
+5V
PC5V
D405
BAV99
ESD_5V
C440 0.1uF
C441 0.1uF
+5V
1
C439 0.1uF
1
R470
UDZS5.6B
2
ZD403
+5V
D403
BAV99
3
DB15
3
16
15
FB412 0 1/16W
PC5V
PC5V
2
14
R434
FB411 0 1/16W
3
13
FB409 0 1/16W
R439
75 1/16W
1
6
2
7
3
8
4
9
5
10
12
1
11
2
17
15” LCD Color Monitor
+5V
1K 1/16W
(2,4)
R444
NC
R445
NC
ZD404
DET_VGA (4)
VSI
0 1/16W
2
100 1/16W
R455
R446
150 1/16W
R486
R447
1K 1/16W
D407
R451
4.7K 1/16W
ZD402
UDZS5.6B
UDZS5.6B
R448
2.2K 1/16W
C442
47pF
R449
2.2K 1/16W
C443
R450
220pF
R452
NC
R453
R454
C444
U201
8
7
6
5
4.7K 1/16W
SCL_VGA
SDA_VGA
100 1/16W
100 1/16W
VCC A0
WP A1
SCL A2
SDA VSS
1
2
3
4
1uF/25V
UDZS5.6B
(4)
(4)
DDCA_SDA
DDCA_SCL
DDC_WP (4)
+3V3
R480
0 1/16W
C113
2
13
12
U202F
NC
4
7
3
0.1uF
VCC
VSY NC
(4)
14
U202A
NC
14
1
0 1/16W
14
14
R494
GND
11
120 OHM
FB407
U202E
NC
10
HSY NC
(4)
R493
7
NC
U202B
7
7
ZD406
UDZS5.6B
M24C02WMN6
ZD405
ZD401
100 1/16W
BAV70
3
HSI
1
UDZS5.6B
ZD412
ESD_5V
0 1/16W
GND
Title
TSUM13AK
Size
B
Date:
19
Document Number
Rev
A
INPUT
Tuesday , May 31, 2005
Sheet
3
of
5
15” LCD Color Monitor
VDVI
Sharp LL-153A
VMPLL VPLL
AVDD
VDDP
VDDC
+5V
0.1uF
61
REFP
GB1P/NC/GB2
GB1N/NC/GB3
GB2P/NC/GB4
GB2N/NC/GB5
GB3P/NC/GB6
GB3N/NC/GB7
REFM
+3V3
TSUM13AK
U402
8
7
3
4
C417
1uF/25V
ROM_WP#
VDD
HOLD#
WP#
VSS
SDO
CE#
SCK
SDI
2
1
6
5
70
71
72
73
CLKBP/LVBCKP/LCK_ODD
CLKBN/LVBCKM/LDE
NC/LVB2P/NC
NC/LVB2M/NC
BB1P/LVB1P/BB2
BB1N/LVB1M/BB3
BB2P/LVB0P/BB4
BB2N/LVB0M/BB5
BB3P/NC/BB6
BB3N/NC/BB7
SST25VF010-33
RST
19
CLKAP/LVB3P/LHSY NC
RSDS/LVDS/TTLCLKAN/LVB3M/LVSY NC
SDO
SCZ
SCK
SDI
RST
R482
10K 1/16W
C421 22pF
32
ESP
OSP
GPO0
GPO1
GPO2
GPO3
GPO4
GPO5
GPO6
XIN
X401
14.318MHz
33
C423 22pF
XOUT
GPIO_P22
GPIO_P23
GPIO_P03
+3V3
R407
R410
NC
NC
102
104
R415
GPIO_P16
GPIO_P15
PWM2/GPIO_P24
GPIO_P27/PWM1
MODE[0]
MODE[1]
GPIO_P16
PWM1/GPIO_P25
R416
10K 1/16W
GPIO_P17/SAR0
GPIO_P00/SAR1
GPIO_P01/SAR2
GPIO_P02/SAR3
10K 1/16W
GPIO_P06
GPIO_P07
PWM0/GPIO_P26
GPIO_P13
GPIO_P14
GND
GND
GND
GND
GND
GND
DDCROM_SCL
DDCROM_SDA
+3V3
(2,3,5) +3V3
2
3
5
6
7
8
118
119
120
121
122
123
124
125
126
127
128
1
PB12
PB13
PB14
PB15
PB16
PB17
PB18
PB19
PB20
PB21
R405
NC
R489
NC
R481
100 1/16W
1
C422
R490
+3V3
+5V
R412
NC
on_BACKLIGHT (2)
adj_BACKLIGHT (2)
R413
Q403
PMBS3906
C425
R426
U303
10K 1/16W
8
VCC
R427 100 1/16W 7
WP
100 1/16W
6
SCK
100 1/16W
5
SI
1uF/25V
A0
A1
A2
VSS
1K 1/16W
+12V
R431 NC
R433 1K 1/16W
NC
R457
1K 1/16W
R456
Volume
OUT-L+
OUT-L-
FUSE_2A
+12V
R488
R474
R475
10K 1/16W
R476
10K 1/16W
10K 1/16W
R477
10K 1/16W
KEY _AUTO1
R418
1K 1/16W
KEY _AUTO
KEY _RIGHT1
R420
1K 1/16W
KEY _RIGHT
KEY _MENU1
R483
1K 1/16W
KEY _MENU
KEY _LEFT1
R484
1K 1/16W
KEY _LEFT
LED_G
LED_A
KEY _POWER
C427
0.1uF
C428
0.1uF
C430
0.1uF
C429
0.1uF
C446
0.1uF
C447
0.1uF
(2)
AUDIO_STBY
R495 10K 1/16W
R496
10K 1/16W AUDIO_MUTE
CN403
OUT-R+
OUT-R-
PMBS3904
Q405
R458
Q404
F601
+3V3
10K 1/16W
1
2
3
4
0.1uF
0 1/8W
LED_A
0 1/16W
LED_G
0 1/16W
+5V
+3V3
R485
R419
PMBS3906
R421
+5V
100 1/16W
100 1/16W
Q401
Volume
AUDIO_MUTE
AUDIO_STBY
R425
R409
NC
C426
CN404
2
4
6
8
10
12
14
R408
10K 1/16W
R414
C424 NC
KEY _POWER1 R411
1
3
5
7
9
11
13
+3V3
10K 1/16W
R417
KEY _RIGHT1
KEY _MENU1
KEY _LEFT1
4.7K 1/16W
4.7K 1/16W
(2,3)
DET_VGA (3)
on_PANEL (2)
22
23
24
25
C419 C420
0.1uF 0.1uF
DDC_WP (3)
+5V
ROM_WP#
KEY _POWER1
77
76
VMPLL
120 OHM
NC
M24C16
1K 1/16W
C416
NC
R406
NC
20
21
R422
R423
FB406
Q402
NC
KEY _AUTO1
R428
R429
R430
VPLL
120 OHM
+3V3
R424
10K 1/16W
FB405
C414 C415
0.1uF 0.1uF
+3V3
10K 1/16W 10K 1/16W
R479
+3V3
(2,3,5) +3V3
PB[12..21] (5)
(2,3,5) +3V3
35
69
78
79
27
28
29
30
31
VDVI
120 OHM
0.1uF
PB[12..21]
80
81
88
87
86
85
84
83
82
75
74
26
FB404
ZD414
R478
100K 1/16W
REXT
UDZS5.6B
62
C401
C409 C410 C411 C412 C413
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
PA[12..13] (5)
9
10
15
16
17
18
ZD413
51
+
10uF/50V
UDZS5.6B
390 1%
R403
0.1uF
(5)
ZD410
C448
PA[0..7]
UDZS5.6B
MAX810STR-2.9V
C408
P[0..7]
13
38
41
47
96
116
0.1uF
PA12
PA13
89
90
91
92
93
94
ZD411
C445
VDDP
UDZS5.6B
12
97
117
68
60
14
67
95
103
115
VDDP
VDDP
VDDP
VDDP
VDDP
52
4
34
RB1P/NC/RB2
RB1N/NC/RB3
RB2P/NC/RB4
RB2N/NC/RB5
RB3P/NC/RB6
RB3N/NC/RB7
C407
120 OHM
ZD409
AVDD
1
GND
AVDD
120 OHM
0.1uF
UDZS5.6B
RESET
Vcc
FB403
+3V3
ZD408
3
2
RST
2
BA1P/NC/BA2
BA1N/NC/BA3
BA2P/NC/BA4
BA2N/NC/BA5
BA3P/NC/BA6
BA3N/NC/BA7
+3V3
(2,3,5)
UDZS5.6B
1
U405
RX2P
RX2N
RX1P
RX1N
RX0P
RX0N
RXCKP
RXCKN
DDCD_SDA
DDCD_SCL
FB402
10uF/50V
C404 C405 C406
0.1uF 0.1uF 0.1uF
R492
10K 1/16W
39
40
42
43
45
46
48
49
36
37
98
99
100
101
105
106
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
UDZS5.6B
3
(2,3)
GA1P/NC/GA2
GA1N/NC/GA3
GA2P/NC/GA4
GA2N/NC/GA5
GA3P/LVA3P/GA6
GA3N/LVA3M/GA7
107
108
109
110
111
112
113
114
+3V3
(2,3,5) +3V3
+ C403
10K 1/16W
R491
+5V
NC/LVACKP/NC
NC/LVACKM/NC
RA1P/LVA2P/RA2
RA1N/LVA2M/RA3
RA2P/LVA1P/RA4
RA2N/LVA1M/RA5
RA3P/LVA0P/RA6
RA3N/LVA0M/RA7
VDDC
120 OHM
ZD407
+5V
VCTRL
VCC1.8
3
DDCA_SDA
DDCA_SCL
+5V
R487
NC
(3)
(3)
RIN0P
RIN0N
GIN0P
GIN0N
SOGIN0
BIN0P
BIN0N
HSY NC0
VSY NC0
DDCA_SDA
DDCA_SCL
(2)
11
2
NC
59
58
56
55
57
54
53
63
64
65
66
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSY NC
VSY NC
VCC1.8 FB401
0.1uF
VDDC
VDDC
VDDC
VDD_OTP
(3)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
1
2
3
4
AVDD_ADC
NC
AVDD_PLL
CN402
AVDD_DVI
AVDD_DVI
NC
U401
AVDD_MPLL
AVDD_MPLL
R402
44
50
C402
R401
CONN
OUT-L+
PMBS3904
F402
FUSE 1A 0603
LED_G
KEY _AUTO
KEY _LEFT
KEY _POWER
OUT-L-
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
LED_A
KEY _MENU
KEY _RIGHT
F401
FUSE 1A 0603
OUT-R-
OUT-R+
Title
TSUM13AK
10K 1/16W
GND
20
CONN
GND
GND
Size
C
Date:
Document Number
Rev
A
SCALER
Tuesday , May 31, 2005
Sheet
4
of
5
15” LCD Color Monitor
(4)
PA[0..7]
Sharp LL-153A
PA[0..7]
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
+3V3
+3V3
(2,3,4)
R728
(4)
PA[12..13]
PA12
PA13
2.2K 1/16W
LVA3P
LVA3M
LVDS_TEST
R729
NC
(4)
PB[12..21]
PB[12..21]
PB12
PB13
PB14
PB15
PB16
PB17
PB18
PB19
PB20
PB21
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
CN101
R730
LVB0M
NC
LVB1M
LVB2M
LVBCKM
LVB3M
LVA0M
LVA1M
LVA2M
LVACKM
LVA3M
RXO1RXO2RXOCRXO3RXE0RXE1RXE2RXECRXE3-
1
3
5
7
9
11
13
15
17
19
21
23
RXO0+
RXO1+
RXO2+
RXOC+
RXO3+
RXE0+
RXE1+
RXE2+
RXEC+
RXE3+
2
4
6
8
10
12
14
16
18
20
22
24
LVB0P
LVB1P
LVB2P
LVBCKP
LVB3P
LVA0P
LVA1P
LVA2P
LVACKP
LVA3P
CONN
VLCD
VLCD
C720
0.1uF
+
C719
47uF/25V
(2)
R732
1K 1/8W
Title
TSUM13AK
Size
B
Date:
21
Document Number
Rev
A
PANEL INTERFACE
Tuesday , May 31, 2005
Sheet
5
of
5
15” LCD Color Monitor
Sharp LL-153A
6.2 Inverter Board
RJ801
0 1/8W
RJ802
0 1/8W
PT801
80GL19T-36-DN
5
7
RJ804
0 1/8W
CN801
2
R836
1K 1/10W
3
4
R819
15 1/8W
8
2
C817
5PF/3KV
N.C C814
1
33G8021-2D-U
R821
100K 1/10W
1000P/50V
R820
15K 1/10W
5
G2N D2N
R822
3M / 1/2W
2
1
2
N.C R823
75K 1/10W
D801
BAV70
D809
LL4148WP
+
N.C C829
0.1uF/50V
Thursday , May 04, 2006
Sheet
2
of
2
R845
1M 1/10W
1M 1/10W
R846
R847
1M 1/10W
C830
0.1uF/25V
R835
C810
470PF/50V
C832
C831
0.1uF/25V
0.1uF/25V
1M 1/10W
C824
0.1uF/25V
R841
430 1/10W 1%
R826
430 1/10W 1%
C819
0.047UF/25V
R817
39K 1/10W
C809
0.047UF/50V
1
6
5
G2N D2N
S2N D2N
G1N D1N
C826
5PF/3KV
D807
LL4148WP
D808
LL4148WP
CN803
2
33G8021-2D-U
1
R832
3M / 1/2W
2
33G8021-2D-U
2
1
4
3
7
8
S1N D1N
1
R843
1K 1/10W
R848
560 1/10W
3
Rev
PWPC1742HDP3P(715G1927 1)
R816
1M 1/10W
R830
15K 1/10W
3
Date:
LL4148WP
CN804
R831
100K 1/10W
SHARP LL-174A 4 LAMPS INVERTER
Document Number
D806
8
N.C R840 N.C C815
2
AM9945
C825
10PF/3KV
1
1000P/50V
Q806
Size
C808
6800PF/50V
R814
56K 1/10W
C820
470UF/25V
33K 1/8W
AOC (Top Victory) Electronics Co., Ltd.
Q810
RK7002
C827
470PF/50V
J825
TIN COATED
Q809
RK7002
C821
0.1uF/25V
2
J824
TIN COATED
J821
TIN COATED
Q808
RK7002
LL4148WP
1
3
4
R829
15 1/8W
J823
TIN COATED
J820
TIN COATED
D805
PT802
80GL19T-36-DN
5
7
C823
1500PF/50V
J819
TIN COATED
Q807
RK7002
Q804
RK7002
J816
TIN COATED
15 1/8W
J818
TIN COATED
R837
16 10 1/10W
15
14
13
12
11
10
9
OZ9938
R828
J817
TIN COATED
J815
TIN COATED
DRV1 PGND
VDDA DRV2
TIMER GNDA
DIM
CT
ISEN SSTCMP
VSEN
LCT
OVPT
ENA
NC1
NC2
C822
1500PF/50V
J814
TIN COATED
R813
1M 1/10W
C805
1000PF/50V
C804
1.5uF/25V
R811
47K 1/10W
C803
0.01UF/50V
R812
10K 1/10W
J812
TIN COATED
R815
100K 1/10W
IC801
1
2
3
4
5
6
7
8
C807
0.01UF/50V
C806
1UF/25V
R810
100K 1/10W
200K 1/10W
R842
10 1/10W
Title
R844
1M 1/10W
R809
200K 1/8W
J811
TIN COATED
D802
BAV99
R827
3.3K 1/10W
DIM
R808
R825
560 1/10W
3
VCC
1
6
1
3
1
N.C R838
0 1/8W
S2N D2N
AM9945
R807
22 1/8W
+5V
8
Q805
CN802
4
N.C R806
470 1/8W
3
ZD801
RLZ5.6B
33G8021-2D-U
C818
470PF/50V
N.C R839
33K 1/8W
1
C816
10PF/3KV
C813
1500PF/50V
VCC
S1N D1N
C801
0.1uF/50V
C812
1500PF/50V
2
1
7
3
2
Q803
PMBS3904
1
G1N D1N
Q802
PMBS3904
+
C811
470UF/25V
2
1
Q801
PMBS3904
2
R803
10K 1/10W
470 1/8W
C828
10K 1/8W
3
ON/OFF
R805
0.1uF/50V
R804
3
R802
300K 1/8W
R818
15 1/8W
+12V
B
22
D803
BAV70
N.C R833
75K 1/10W
R834
3.3K 1/10W
D804
BAV99
15” LCD Color Monitor
Sharp LL-153A
6.3 Adapter Board
2
R908
680K 1/4W
ZD906
NC
!
4
R918
10 1/4W
100KΩ 1% 1/4W
L901
R919
10K 1/8W
C917
0.001uF
!
!
C915
0.1uF/25V
RLZ22B
NR901
NTCR
t
F902
!
R915
100 1/8W
F901
FUSE
!
D903
LL4148WP
R913
4.7K 1/8W
C916
0.1uF/25V
NC
CN903
3
ZD904
RLZ12B
1
ZD902
RLZ5.1B
R921
3.6K 1/8W
DIM
R926
1K 1/8W
1
R920
33K 1/8W
ON/OFF
C918
1uF/25V
CN902
CONN
2
4
6
8
10
12
1
3
5
7
9
11
+12V
+5V
R923
1K 1/8W
R925
0 1/8W
R924
1K 1/8W
R922
2.43K 1/8W
AZ431AZ-AE1
C913
3
NC
R904
0.68Ω 2W
IC903
Q902
PMBS3904
C908
NC
R927
100 1/4W
PMBS3906
FUSE
!
R912
2.7KΩ 1/8W
C910
0.1uF/25V
CONN(NC)
Q901
1
R902
R903
680K 1/4W
680K 1/4W
C920
FB901
BEAD
3
2
!
ZD901
C911
470UF/25V
0.001uF/250V
4
R911
4.7K 1/4W
+
3
2
1
IC902
PC123X8Y FZOF
C903
0.47uF/275V
C912
1000uF/25V
F801
+
!
C919
470pF/25V
3.5uH
+5V
2
3
2
R928
220 1/4W
ZD903
PTZ7.5B
C921
1
2.0MH
!
!
SP10150
Q903
2SK2645-54MR
ZD905
RLZ18B
LD7552BPS
C907
0.1uF/25V
2
1
R930
D904
2
!
5
6
7
8
+ C906
470UF/25V
L904
C932
0.001uF
+
POWER X'FMR
1
C901
0.001uF/250V
!
RT
NC
VCC
CS
COMP VCC
GND OUT
+ C909
1000uF/25V
11
R932
680K 1/4W
U?
4
3
2
1
R937 100 1/4W
7
2
VAR901
Varistor
+12V
+ C904
NC
R916 100 1/4W
R936 100 1/4W
6
C922
22uF/50V
1
R931
430K 1/4W
9
10
4
5
5.1 1/4W
D905
FR103
+
!
3
R914
0Ω 1/4W
8
2
D901
FR107
2
C914
0.1uF
T901
3
SG901
!
C902
0.001uF/250V
R901
680K 1/4W
1
1
R910
430K 1/4W
C930
1500pF/1KV
3.5uH
2
R907
680K 1/4W
D906
3
SG902
2
R909
430K 1/4W
NC
NC
4
!
1
!
C905
100uF/450V
L903
SP10150
2
D902
1
1
+
!
1
-
100K 2W
L902
17.0mH
C933
0.0022uF
R905
1
3
C931
0.0022uF
2
+
!
2
4
R935
100 1/4W
R934
100 1/4W
R906
100 1/4W
BD901
U4KB80R
NC
2
1
CN901
SOCKET
!
CN301
TPV (Top Victory) Electronics Co., Ltd.
CN302
5
4
3
2
1
3
2
1
PHONEJACK
INR
GND
INL
CONN & WIRE
23
Title
Size
Date:
POWER OUTPUT 12V & 5 V
Document Number
F OR SHARP L L 154
Rev
( PWPC521CP1P) F
Sheet
1
of
2
15” LCD Color Monitor
Sharp LL-153A
6.4 Audio Board
24
15” LCD Color Monitor
Sharp LL-153A
7. PCB Layout
7.1 Main Board
25
15” LCD Color Monitor
Sharp LL-153A
7.2 PWPC Board
26
15” LCD Color Monitor
Sharp LL-153A
7.3 Audio Board
715G1144-3-SH
27
15” LCD Color Monitor
Sharp LL-153A
7.4 Key Board
8. Maintainability
8.1 Equipments and Tools Requirement
1.
Voltmeter.150
2.
Oscilloscope.
3.
Pattern Generator.
4.
DDC Tool with an IBM Compatible Computer.
5.
Alignment Tool.
6.
LCD Color Analyzer.
7.
Service Manual.
8. User Manual.
28
15” LCD Color Monitor
Sharp LL-153A
8.2 Trouble Shooting
8.2.1 MAIN BOARD
NO SCREEN APPEAR
Measured CN701 pin5,6 = 12 V?
Measured CN701 pin 9,10= 5V?
Measured U702 pin 2= 3.3V?
Measured U602 pin 2= 1.8V?
Measured CN402 pin 1/2 = 5V?
Measured CN402 pin 3/4 = 3.3V?
NG
Check Correspondent component.
Is there any shortage or cold solder?
Yes .there have OSD show
Yes, all DC level exist
Disconnected the Signal cable( Loose the
Signal cable ),Is the screen show “Cable Not
Connected” ?
No, nothing is
Led Orange
Connected the Signal cable
Led Green
Connected the Signal cable again,
Check LED status.
Replace U402
Flash Rom
Check Power switch is in Power-on
status , and check if Power switch had
been stuck ?
Led orange
again
Led Green
OK, Keyboard no
Check the Wire-Harness from CN405
Measured RGB (R434, R435, R436 )
H,V Input at U401 pin 63,64 ,was there
have signal ?
Check Correspondent
component short/open
( Protection Diode )
OK, Wire tight
NG
Check Panel-Power Circuit Block
OK, input Normal
OK ,Panel Power
Check U401 Data-output Block
NG,still no screen
OK, U201 data
Replace Power board and Check
Inverter control relative circuit
OK, clock
Replace U401 (TSUM13AK)
Re-do White balance adjust
OK
Note:1. If replace “MAIN-BOARD” , Please re-do “DDC-content” programmed & “WHITE-Balance”.
2. If replace “Power Board” only, Please re-do “ WHITE-Balance”
29
15” LCD Color Monitor
Sharp LL-153A
2.PANEL POWER CIRCUIT
Check R731 should have response from 0V to 5V
NG , no transition
Check the PPWR panel power relative circuit,
Mea
When we switch the power switch from on to off
Q704(pin2)
In normal operation, when LED =green, R731
should =0 v,
OK
Yes
Measured the Q706 pin 3= 5 V?
OK
Replace Q602 ( N-MOS, A03401)
NG, no Voltage
OK
3. INVERTER CONTROL RELATIVE CIRCUIT
Measured the inverter connector
CN701
Check the Bklt-On relative circuit, R711, R712,
NG
In normal operation, when LED =green,
R711,R712 Bklt-On should =5 v,
Pin2 on/off control=5V (on)
If Bklt-On no-response when the power switch
Pin4 PWM signal control dim 0V-5V
Replace power board to new-one and check
turn on-off, Replace U401 TSUM13AK
NG
the screen is normal?
Replace Power board
& Re-do white balance
OK
30
15” LCD Color Monitor
Sharp LL-153A
4. U4-DATA OUTPUT
Measured DCLK(pin 65,66 from U401)
NG , no transition
DVS, DHS (pin 63,64 from U401 )
Is the waveform ok?
Replace TSUM13AK (U401) or
DCLK around 48 MHZ , DVS=60.09Hz , DHS around 80
replace Main board.
KHz ?(refer to input signal=640x480@60 Hz 31k, and
LED is Green)
OK
Check TSUM13AK(U401)
If Main Board being replace, please
Signal output (PIN105-114, 118-127)
do the DDC – content reprogrammed
Is the waveform ok ?
OK
OK
8.2.2 Keypad Board
OSD is unstable or not working
N
Connect Key Pad Board
Is Key Pad Board connecting normally?
Y
N
Is Button Switch normally?
Replace Button Switch
Y
N
Is Key Pad Board normally?
Y
Check main board
31
Replace Key Pad Board
15” LCD Color Monitor
Sharp LL-153A
8.2.3 Power/Inverter Board
1.) No power
Check CN902 pin5, 6 = 12V
NG
Check Interface board
OK
Check AC line volt 120V or 220V
OK
NG
Change AC input
Check the voltage of C905(+)
OK
NG
Check bridge rectified circuit and F901 circut
Check start voltage for the pin3 of IC901
OK
NG
Change R909,R910,R931 and Change IC901
Check the auxiliary voltage is bigger than 10V
smaller than 20V
NG
1) Check IC901
OK
2) Check ZD901, R915,C916…OVP circuit
Check IC901 pin8 PWM wave
NG
Check IC901
OK
Check Q903,R918, R919, R928,T901,ZD905,D901
32
15” LCD Color Monitor
Sharp LL-153A
2.) W / LED , No Backlight
Check C811(+) =12V
NG
Change L921 circuit
OK
Check ON/OFF signal
NG
Check Main board
OK
Check IC801 pin2=5V
NG
Change Q801,Q802,Q803 circuit
OK
Check the pin1,15 of IC801 have saw tooth wave
NG
Check IC801 pin6,7,10
OK
Check the pin5 of IC801
NG
Check D802,D804,Q806 circuit
OK
Check the resonant wave for PT801
OK
NG
Check Q805 circuit
Check the output of PT801
NG
OK
Change PT801
Check connecter & lamp
33
15” LCD Color Monitor
Sharp LL-153A
9. White-Balance, Luminance Adjustment
Approximately 30 minutes should be allowed for warm up before proceeding White-Balance adjustment.
1. How to do the CA210 MEM. Channel setting
A. Reference to CA210 user guide
B. Use “ SC” key and “ NEXT” key to modify x, y, Y value and use “ID” key to modify the TEXT description
Following is the procedure to do white-balance adjust:
2. Setting the color temp. you want
A. MEM.CHANNEL 1 (9300K color):
9300K color temp. parameter is x = 383±20, y = 297±15,
B. MEM.CHANNEL 2 (7500K color):
7500K color temp. parameter is x = 299±20, y = 315±15,
C. MEM.CHANNEL 3 (6500K color):
6500K color temp. parameter is x = 313±20, y = 329±15,
D. MEM.CHANNEL 3 (5000K color):
5000K color temp. parameter is x = 364±20, y = 359±15,
E. MEM.CHANNEL 3 (4000K color):
4000K color temp. parameter is x = 282±20, y = 384±15,
3. Into factory mode of SHARP LL-154A
Turn on power, press the MENU button, pull out the power cord, and then plug the power cord. Then the factory
OSD will be at the left top of the panel.
4. Bias adjustment:
Set the Contrast
to 64; Adjust the Brightness
to 31.
5. Gain adjustment:
Move cursor to “-F-” and press MENU key
A. Adjust 9300K color-temperature
1. Switch the CA210 to 9300 (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 283±15, y = 297±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
B. Adjust 7500K color-temperature
1. Switch the CA210 to 7500 (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 299±15, y = 315±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
34
15” LCD Color Monitor
Sharp LL-153A
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
C. Adjust 6500K color-temperature
1. Switch the CA210 to STD (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 313±15, y = 329±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
D. Adjust 5000K color-temperature
1. Switch the CA210 to 5000 (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 346±15, y = 359±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
E. Adjust 4000K color-temperature
1. Switch the CA210 to 4000 (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 282±15, y = 384±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
C. Turn the Power-button off to quit from factory mode.
35
15” LCD Color Monitor
Sharp LL-153A
10. Monitor Exploded View
36
15” LCD Color Monitor
Sharp LL-153A
11. BOM List
T56CM5NJXXXWAJ
Location
Part No.
Description
AUPC560KB8P
AUPC BOARD FOR SMT
CBPC6CM5XWJ1
MAIN BOARD
KEPC6JA9
KEY BOARD
PWPC521CP1P
G2152-F-X-X-1-20061121
11G6055
1
口字框
11G6082
1
CLAMP
12G 394
3
FOOT
12G6051
1
Thermal Pal
15G5791
1
VESA BRACKET
34G1298 8M ST
REAR COVER
34G1630A8M
T
FRONT COVER
34G1631 8M
T
STAND
34G1632 8M
T
BASE
37G 495
1
HINGE
44G3231 15
EVA WASHER
45G8088607SH3
EPE BAG FOR MONITOR
52G
1150 SH
BLACK TAPE
52G
1210
AL Foil
52G6019
A
1
YELLOW TAPE
52G6022 22 GP
Adhesive tape
52G6025 11582
MYLAR SHIELD
52G8001
8
NON-WOVEN FABRICS
78G 314
2
85G 707
1
K
LCD Speaker
MAIN SHIELD
89G 17356G556
AUDIO CABLE
89G 728GAB901
SIGNAL CABLE
89G401D18NISA
POWER CORD
95G8014 12 36
HARNESS 12P-12P 80mm
95G8014 16 46
HARNESS 12P-16P 180MM
95G8018 24701
D
WIRE HARNESS 20P-24P 115
XN01A
M1G 330
4120
SCREW
XN01B
M1G 330
4120
SCREW
XN01C
M1G 330
4120
SCREW
XN01A
M1G 330
6120
SCREW
XN01A
M1G1140
5120
SCREW
XN01A
M1G1730
6120
M3*6
XN01B
M1G1730
6120
M3*6
37
15” LCD Color Monitor
Sharp LL-153A
XN01C
M1G1730
6120
M3*6
XN01A
Q1G 330
6120
SCREW M3X6MM
XN01A
Q1G 330 10120
SCREW
XN01A
Q1G1030
SCREW 3X8 NI
8120
705GP503 1A SH
PAPER PAD ASS'Y
750GLC50P1Q13N
PANEL LCD CLAA150XP01Q 0
XN01A
AM1G1740 10120
SCREW
D-SUB
J02G 247 SH
SCREW
J15G0030
MAIN FRAME
1
J44GP504624 1A
CARTON
J45G8088609SH1
EPE BAG FOR BASE
J52G8025 11823
INSULATE SHEET
AUPC560KB8SMTP
AUPC BOARD FOR SMT
12G 408 10
THERMAL PAD
CN204
33G3278
WAFER 3P PLUG 2.55mm
CN202
33G802414C
U201
56G 616
R212
61G 60222452T
220KOHM 5% 1/6W
C205
67G215L471 3N
470UF/16V
C207
67G215L471 3N
470UF/16V
C208
67G215L471 3N
470UF/16V
C201
67G215L681 4N
680UF 25V
C202
67G215L681 4N
680UF 25V
90G6093
HEAT SINK
3
H
WAFER
1
AMPLIFIER IC E-TDA7496L
1
AUPC560KB8AIP
AUPC BOARD FOR AI
R207
61G0603102
CHIPR 1KOHM +-5% 1/10W
R208
61G0603102
CHIPR 1KOHM +-5% 1/10W
R201
61G0603183
CHIP resistors 1/10W
R203
61G0603183
CHIP resistors 1/10W
R210
61G0603203
RST CHIP 20K 1/10W 5%
R211
61G0603203
RST CHIP 20K 1/10W 5%
R202
61G0603204
RST CHIP 200K 1/10W 5%
C211
65G0805101 31
CHIP 100PF 50V NPD 0805
C212
65G0805101 31
CHIP 100PF 50V NPD 0805
C203
65G0805104 32
CHIP 0.1UF 50V X7R 0805
C213
65G0805104 32
CHIP 0.1UF 50V X7R 0805
C204
65G0805474 22
CHIP 0.47UF 25V Y5V 0805
C206
65G0805474 22
CHIP 0.47UF 25V Y5V 0805
C209
67G 2151097NT
1UF/50V
C210
67G 2151097NT
1UF/50V
38
15” LCD Color Monitor
Sharp LL-153A
715G1144
3 SH
PCB
SMTC6CM5XWJ1
MAIN BOARD
CN404
33G801714H
H
PIN2*7
CN701
33G8027 12
WAFER 2*6P 2.0MM R/A
CN403
33G8027 16
WAFER 16PIN 2.0MM DIP
CN101
33G8027 24
H
PIN 24P 2.0MM RIGHT ANGL
40G 45762412B
CBPC LABEL
C403
67G215V100 7N
LOW ESR EC 10UF 50V NCC
C408
67G215V100 7N
LOW ESR EC 10UF 50V NCC
C610
67G215V101 4N
LOW ESR EC 100UF 25V NCC
C707
67G215V101 4N
LOW ESR EC 100UF 25V NCC
C710
67G215V101 4N
LOW ESR EC 100UF 25V NCC
C609
67G215V221 4N
LOW ESR EC 220UF 25V NCC
C601
67G215V470 4N
LOW ESR EC 47UF 25V NCC
C602
67G215V470 4N
LOW ESR EC 47UF 25V NCC
C717
67G215V470 4N
LOW ESR EC 47UF 25V NCC
C719
67G215V470 4N
LOW ESR EC 47UF 25V NCC
L602
73G 253158
CHOKE COIL
CN405
88G353A15F HJ
D-SUB 15PIN
90G6250
Radiator
L
1 GP
X401
93G
22 53
CRYSTAL 14.31818MHZ HC-4
U601
56G 133 32 NS
IC LM3485 MSOP-8
U401
56G 562102
TSUM13AK-LF PQFP-128
U602
56G 563 34
IC AIC1084-18PM TO-263
U405
56G 643 5A
MAX810STRG SOT-23 IC
U201
56G1133 34
IC M24C02-WMN6TP
U303
56G1133 56
IC M24C16-WMN6TP
U402
56G1133 81
Q404
57G 417
4
PMBS3904/PLILIPS
Q405
57G 417
4
PMBS3904/PLILIPS
Q701
57G 417
4
PMBS3904/PLILIPS
Q703
57G 417
4
PMBS3904/PLILIPS
Q401
57G 417
6
PMBS3906 PNP
Q403
57G 417
6
PMBS3906 PNP
Q602
57G 763
1
AO3401L
Q704
57G 763
1
AO3401L
F401
61G0603000
CHIPR 0OHM +-5% 1/10W
F402
61G0603000
CHIPR 0OHM +-5% 1/10W
FB409
61G0603000
CHIPR 0OHM +-5% 1/10W
FB411
61G0603000
CHIPR 0OHM +-5% 1/10W
X
SST25LF020A-33-4C-SAE
39
15” LCD Color Monitor
Sharp LL-153A
FB412
61G0603000
CHIPR 0OHM +-5% 1/10W
R419
61G0603000
CHIPR 0OHM +-5% 1/10W
R421
61G0603000
CHIPR 0OHM +-5% 1/10W
R480
61G0603000
CHIPR 0OHM +-5% 1/10W
R493
61G0603000
CHIPR 0OHM +-5% 1/10W
R494
61G0603000
CHIPR 0OHM +-5% 1/10W
R702
61G0603000
CHIPR 0OHM +-5% 1/10W
R409
61G0603101
CHIPR 100OHM +-5% 1/10W
R414
61G0603101
CHIPR 100OHM +-5% 1/10W
R427
61G0603101
CHIPR 100OHM +-5% 1/10W
R428
61G0603101
CHIPR 100OHM +-5% 1/10W
R429
61G0603101
CHIPR 100OHM +-5% 1/10W
R441
61G0603101
CHIPR 100OHM +-5% 1/10W
R442
61G0603101
CHIPR 100OHM +-5% 1/10W
R443
61G0603101
CHIPR 100OHM +-5% 1/10W
R445
61G0603101
CHIPR 100OHM +-5% 1/10W
R453
61G0603101
CHIPR 100OHM +-5% 1/10W
R454
61G0603101
CHIPR 100OHM +-5% 1/10W
R455
61G0603101
CHIPR 100OHM +-5% 1/10W
R481
61G0603101
CHIPR 100OHM +-5% 1/10W
R486
61G0603101
CHIPR 100OHM +-5% 1/10W
R411
61G0603102
CHIPR 1KOHM +-5% 1/10W
R418
61G0603102
CHIPR 1KOHM +-5% 1/10W
R420
61G0603102
CHIPR 1KOHM +-5% 1/10W
R430
61G0603102
CHIPR 1KOHM +-5% 1/10W
R433
61G0603102
CHIPR 1KOHM +-5% 1/10W
R447
61G0603102
CHIPR 1KOHM +-5% 1/10W
R456
61G0603102
CHIPR 1KOHM +-5% 1/10W
R470
61G0603102
CHIPR 1KOHM +-5% 1/10W
R483
61G0603102
CHIPR 1KOHM +-5% 1/10W
R484
61G0603102
CHIPR 1KOHM +-5% 1/10W
R701
61G0603102
CHIPR 1KOHM +-5% 1/10W
R707
61G0603102
CHIPR 1KOHM +-5% 1/10W
R731
61G0603102
CHIPR 1KOHM +-5% 1/10W
R408
61G0603103
CHIPR 10KOHM+-5% 1/10W
R413
61G0603103
CHIPR 10KOHM+-5% 1/10W
R415
61G0603103
CHIPR 10KOHM+-5% 1/10W
R416
61G0603103
CHIPR 10KOHM+-5% 1/10W
R424
61G0603103
CHIPR 10KOHM+-5% 1/10W
R425
61G0603103
CHIPR 10KOHM+-5% 1/10W
40
15” LCD Color Monitor
Sharp LL-153A
R426
61G0603103
CHIPR 10KOHM+-5% 1/10W
R458
61G0603103
CHIPR 10KOHM+-5% 1/10W
R474
61G0603103
CHIPR 10KOHM+-5% 1/10W
R475
61G0603103
CHIPR 10KOHM+-5% 1/10W
R476
61G0603103
CHIPR 10KOHM+-5% 1/10W
R477
61G0603103
CHIPR 10KOHM+-5% 1/10W
R479
61G0603103
CHIPR 10KOHM+-5% 1/10W
R488
61G0603103
CHIPR 10KOHM+-5% 1/10W
R490
61G0603103
CHIPR 10KOHM+-5% 1/10W
R491
61G0603103
CHIPR 10KOHM+-5% 1/10W
R492
61G0603103
CHIPR 10KOHM+-5% 1/10W
R495
61G0603103
CHIPR 10KOHM+-5% 1/10W
R496
61G0603103
CHIPR 10KOHM+-5% 1/10W
R708
61G0603103
CHIPR 10KOHM+-5% 1/10W
R711
61G0603103
CHIPR 10KOHM+-5% 1/10W
R714
61G0603103
CHIPR 10KOHM+-5% 1/10W
R478
61G0603104
CHIPR 100KOHM +-5% 1/10W
R446
61G0603151
CHIPR 150 OHM +-5% 1/10W
R608
61G0603200 2F
RST CHIP 20K 1/10W 1%
R605
61G0603220
CHIPR 22OHM+-5% 1/10W
R448
61G0603222
CHIPR 2.2KOHM+-5% 1/10W
R449
61G0603222
CHIPR 2.2KOHM+-5% 1/10W
R728
61G0603222
CHIPR 2.2KOHM+-5% 1/10W
R607
61G0603330 2F
RST CHIP 33K 1/10W 1%
R606
61G0603333
RST CHIP 33K 1/10W 5%
R403
61G0603390 0F
390OHM +-1%
R437
61G0603471
CHIPR 470OHM+-5%1/10W
R405
61G0603472
CHIP
4.7KOHM +-5% 1/10W
R422
61G0603472
CHIP
4.7KOHM +-5% 1/10W
R450
61G0603472
CHIP
4.7KOHM +-5% 1/10W
R451
61G0603472
CHIP
4.7KOHM +-5% 1/10W
R705
61G0603472
CHIP
4.7KOHM +-5% 1/10W
R712
61G0603472
CHIP
4.7KOHM +-5% 1/10W
R717
61G0603472
CHIP
4.7KOHM +-5% 1/10W
R723
61G0603513
CHIP 51K OHM
R434
61G0603560
RST CHIP 56R 1/10W 5%
R435
61G0603560
RST CHIP 56R 1/10W 5%
R436
61G0603560
RST CHIP 56R 1/10W 5%
R438
61G0603750
CHIPR 75OHM+-5%1/10W
R439
61G0603750
CHIPR 75OHM+-5%1/10W
41
15” LCD Color Monitor
Sharp LL-153A
R440
61G0603750
CHIPR 75OHM+-5%1/10W
ZD404
61G0805000
RST CHIP MAX
F601
61G1206000
CHIP resistors 1/3W
F602
61G1206000
CHIP resistors 1/3W
R485
61G1206000
CHIP resistors 1/3W
R732
61G1206102
CHIP 1K OHM 5% 1/8W
C435
65G0603102 32
CHIP 1000PF 50 X7R
C611
65G0603102 32
CHIP 1000PF 50 X7R
C612
65G0603102 32
CHIP 1000PF 50 X7R
C613
65G0603102 32
CHIP 1000PF 50 X7R
C614
65G0603102 32
CHIP 1000PF 50 X7R
C113
65G0603104 32
CHIP 0.1UF 50V X7R
C401
65G0603104 32
CHIP 0.1UF 50V X7R
C402
65G0603104 32
CHIP 0.1UF 50V X7R
C404
65G0603104 32
CHIP 0.1UF 50V X7R
C405
65G0603104 32
CHIP 0.1UF 50V X7R
C406
65G0603104 32
CHIP 0.1UF 50V X7R
C407
65G0603104 32
CHIP 0.1UF 50V X7R
C409
65G0603104 32
CHIP 0.1UF 50V X7R
C410
65G0603104 32
CHIP 0.1UF 50V X7R
C411
65G0603104 32
CHIP 0.1UF 50V X7R
C412
65G0603104 32
CHIP 0.1UF 50V X7R
C413
65G0603104 32
CHIP 0.1UF 50V X7R
C414
65G0603104 32
CHIP 0.1UF 50V X7R
C415
65G0603104 32
CHIP 0.1UF 50V X7R
C416
65G0603104 32
CHIP 0.1UF 50V X7R
C419
65G0603104 32
CHIP 0.1UF 50V X7R
C420
65G0603104 32
CHIP 0.1UF 50V X7R
C426
65G0603104 32
CHIP 0.1UF 50V X7R
C427
65G0603104 32
CHIP 0.1UF 50V X7R
C428
65G0603104 32
CHIP 0.1UF 50V X7R
C429
65G0603104 32
CHIP 0.1UF 50V X7R
C430
65G0603104 32
CHIP 0.1UF 50V X7R
C439
65G0603104 32
CHIP 0.1UF 50V X7R
C440
65G0603104 32
CHIP 0.1UF 50V X7R
C441
65G0603104 32
CHIP 0.1UF 50V X7R
C445
65G0603104 32
CHIP 0.1UF 50V X7R
C446
65G0603104 32
CHIP 0.1UF 50V X7R
C447
65G0603104 32
CHIP 0.1UF 50V X7R
C448
65G0603104 32
CHIP 0.1UF 50V X7R
42
0R05
1/8W
15” LCD Color Monitor
Sharp LL-153A
C603
65G0603104 32
CHIP 0.1UF 50V X7R
C604
65G0603104 32
CHIP 0.1UF 50V X7R
C701
65G0603104 32
CHIP 0.1UF 50V X7R
C706
65G0603104 32
CHIP 0.1UF 50V X7R
C709
65G0603104 32
CHIP 0.1UF 50V X7R
C711
65G0603104 32
CHIP 0.1UF 50V X7R
C720
65G0603104 32
CHIP 0.1UF 50V X7R
C421
65G0603220 31
CHIP 22PF 50V NPO
C423
65G0603220 31
CHIP 22PF 50V NPO
C443
65G0603221 31
CAP:CER 220PF 5% 50V SMT
C442
65G0603470 31
CHIP 47PF 50V NPO
C432
65G0603473 32
CHIP 47NF 50V X7R
C433
65G0603473 32
CHIP 47NF 50V X7R
C434
65G0603473 32
CHIP 47NF 50V X7R
C436
65G0603473 32
CHIP 47NF 50V X7R
C437
65G0603473 32
CHIP 47NF 50V X7R
C438
65G0603473 32
CHIP 47NF 50V X7R
C417
65G0805105 22
CHIP 1UF 25V X7R 0805
C425
65G0805105 22
CHIP 1UF 25V X7R 0805
C444
65G0805105 22
CHIP 1UF 25V X7R 0805
C708
65G0805105 22
CHIP 1UF 25V X7R 0805
FB401
71G 56K121
M
GP
CHIP BEAD 120OHM T
FB402
71G 56K121
M
GP
CHIP BEAD 120OHM T
FB403
71G 56K121
M
GP
CHIP BEAD 120OHM T
FB404
71G 56K121
M
GP
CHIP BEAD 120OHM T
FB405
71G 56K121
M
GP
CHIP BEAD 120OHM T
FB406
71G 56K121
M
GP
CHIP BEAD 120OHM T
FB407
71G 56K121
M
GP
CHIP BEAD 120OHM T
FB413
71G 56K121
M
GP
CHIP BEAD 120OHM T
FB701
71G 56K121
M
GP
CHIP BEAD 120OHM T
D407
93G
64 42
P
D403
93G
6433P
BAV99 SOT-23
D404
93G
6433P
BAV99 SOT-23
D405
93G
6433P
BAV99 SOT-23
ZD401
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD402
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD403
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD405
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD406
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD407
93G 39S 34
T
ZENER DIODE UDZS5.6B
BAV70 DIODE
43
15” LCD Color Monitor
Sharp LL-153A
ZD408
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD409
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD410
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD411
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD412
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD413
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD414
93G 39S 34
T
ZENER DIODE UDZS5.6B
D602
93G5004
2
715G1590
SSM54PT SMA DIODE 5A 40V
1
MAIN BOARD PCB
SMTKEPC6JA9
KEYBOARD FOR SMT
CN102
33G3802 2H
WAFTER
CN103
33G3802 2H
WAFTER
CN101
33G8027 12
H
WAFER 2*6P 2.0mm R/A
R103
61G 60210152T
CFR 1/6W 100OHM +-5%
R104
61G 60210152T
CFR 1/6W 100OHM +-5%
R101
61G 60251152T
CFR 1/6W 510OHM +-5%
R102
61G 60251152T
CFR 1/6W 510OHM +-5%
SW1
77G 600
1GCJ
Switch
SW2
77G 600
1GCJ
Switch
SW3
77G 600
1GCJ
Switch
SW4
77G 600
1GCJ
Switch
SW5
77G 600
1GCJ
Switch
D101
81G
CN104
88G 30211K
PHONE JOCK
J1
95G 900 58
WIRE HARNESS
ZD101
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD102
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD103
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD104
93G 39S 34
T
ZENER DIODE UDZS5.6B
ZD105
93G 39S 34
T
ZENER DIODE UDZS5.6B
12 1F GP
715G1591
LED
2
KEPC PCB
PW521CP1SMTP
POWER BOARD FOR SMT
W901
9G6005
PIN FOOT
CN801
33G8020 2D AC
CONN,2P R/A DIP BY ACES
CN802
33G8020 2D AC
CONN,2P R/A DIP BY ACES
CN902
33G8027 12
WAFER 2*6P 2.0MM R/A
40G 45762412B
CBPC LABEL
51G
RTV Glue
1
6
45056863
IC902
56G 139 3A
VAR901
61G
46
PC123Y22FZOF
9
10471
44
15” LCD Color Monitor
Sharp LL-153A
NR901
61G
58080 WT
NTCR
C903
63G 10747410S
0.47UF +-10% 250VAC
C816
65G
3J2206ET
22PF 5% 3KV TDK
C817
65G
3J5096ET
5PF 5% SL 3KV
C901
65G306M1022BM
Y1.CAP.001UF 250VAC MURA
C902
65G306M1022BM
Y1.CAP.001UF 250VAC MURA
C921
65G306M1022BM
Y1.CAP.001UF 250VAC MURA
C909
67G215L102 4N
LOW ESR 1000UF 25V
C912
67G215L102 4N
LOW ESR 1000UF 25V
C811
67G215L471 4Q
LOW ESR EC 470UF 25V UH
C906
67G215L471 4Q
LOW ESR EC 470UF 25V UH
C911
67G215L471 4Q
LOW ESR EC 470UF 25V UH
C905
67G215S10115Q
LOWESR EC 100UF 450V PAG
FB901
71G
Φ3.5*Φ0.8*2.2\ 100MM>
L903
73G 253 91 LS
CHOKE COIL
L904
73G 253 91 LS
CHOKE COIL
L901
73L 174 53 LG
GP
LINE FILTER
L902
73L 174 55 LG
GP
LINE FILTER
PT801
80GL15T 30 DN
T901
80LL19T
CN301
88G 30214K
PHONE JACK 5PIN
BD901
93G
50460900
GBU408
D901
93G
6026T52T
FR107-DO-41 1000V/1A
D905
93G
6038T52T
FR103 DO-41 200V/1A
CN302
95G8013
55 29
7 LG
3704
X'FMR 74uH TK.2026.101
GP
TRANSFORMER
X
HARNESS
705G 560 57S44
R905 ASS'Y
705G 780 57S7P
Q903 ASS'Y
705GJ5K0 61001
R904 ASS'Y
705GJ5K0 87001
CN901 ASS'Y
705GJ5K0 93001
D902 ASS'Y
705GJ5K0 93002
D904 ASS'Y
705GJ5K0 95001
JP907 ASS'Y
PW521CP1AIP
POWER FOR AI
IC901
56G 379 76
IC LD7552BPS SOP-8
IC801
56G 608 10
OZ9938GN SOIC-16
Q801
57G 417
4
PMBS3904/PLILIPS
Q802
57G 417
4
PMBS3904/PLILIPS
Q803
57G 417
4
PMBS3904/PLILIPS
Q902
57G 417
4
PMBS3904/PLILIPS
Q901
57G 417
6
PMBS3906 PNP
45
15” LCD Color Monitor
Sharp LL-153A
Q804
57G 759
2
TRANSISTOR RK7002 SOT-3
Q806
57G 759
2
TRANSISTOR RK7002 SOT-3
Q807
57G 759
2
TRANSISTOR RK7002 SOT-3
Q808
57G 759
2
TRANSISTOR RK7002 SOT-3
Q805
57G 763 14
AM9945N-T1-PF
R839
61G0805000
RST CHIP MAX
0R05
1/8W
R844
61G0805000
RST CHIP MAX
0R05
1/8W
R925
61G0805000
RST CHIP MAX
0R05
1/8W
RJ824
61G0805000
RST CHIP MAX
0R05
1/8W
R836
61G0805100
RST CHIP 10R 1/8W 5%
R837
61G0805100
RST CHIP 10R 1/8W 5%
R826
61G0805100 2F
RST CHIP 10K 1/8W 1%
R915
61G0805101
RST CHIP 100R 1/8W 5%
R923
61G0805102
CHIPR 1K OHM +-5% 1/10W
R924
61G0805102
CHIPR 1K OHM +-5% 1/10W
R926
61G0805102
CHIPR 1K OHM +-5% 1/10W
R803
61G0805103
CHIP 10KOHM 1/10W
R804
61G0805103
CHIP 10KOHM 1/10W
R812
61G0805103
CHIP 10KOHM 1/10W
R820
61G0805103
CHIP 10KOHM 1/10W
R919
61G0805103
CHIP 10KOHM 1/10W
R810
61G0805104
RST CHIP 100K 1/8W 5%
R815
61G0805104
RST CHIP 100K 1/8W 5%
R821
61G0805104
RST CHIP 100K 1/8W 5%
R813
61G0805105
RST CHIP 1M 1/8W 5%
R816
61G0805105
RST CHIP 1M 1/8W 5%
R845
61G0805105
RST CHIP 1M 1/8W 5%
R847
61G0805105
RST CHIP 1M 1/8W 5%
R848
61G0805105
RST CHIP 1M 1/8W 5%
R809
61G0805204
RST CHIPR 200 KOHM +-5%
R807
61G0805220
RST CHIP 22R 1/8W 5%
R840
61G0805242
RST CHIP 2K4 1/8W 5%
R841
61G0805242
RST CHIP 2K4 1/8W 5%
R922
61G0805243 1F
RST CHIPR 2.43 KOHM +-1%
R825
61G0805271
CHIPR 270 OHM +-50% 1/8W
R912
61G0805272
RST CHIP 2K7 1/8W 5%
R802
61G0805304
RST CHIPR 300 KOHM +-5%
R920
61G0805330 2F
CHIP 33KOHM 1/10W/1%
R838
61G0805360 0F
RST CHIPR 360 OHM +-1% 1
R921
61G0805360 1F
CHIP 3.6KOHM 1/10W 1%
46
SOIC-8
15” LCD Color Monitor
Sharp LL-153A
R817
61G0805360 2F
RST CHIPR 36 KOHM +-1% 1
R843
61G0805471
RST CHIP 470R 1/8W 5%
R913
61G0805472
RST CHIP 4K7 1/8W 5%
R811
61G0805473
RST CHIP 47K 1/8W 5%
R827
61G0805510 1F
RST CHIPR 5.1 KOHM +-1%
R814
61G0805563
RST CHIP 56K 1/8W 5%
D906
61G1206000
CHIP resistors 1/3W
JR902
61G1206000
CHIP resistors 1/3W
R801
61G1206000
CHIP resistors 1/3W
R918
61G1206100
RST CHIP 10R 1/4W 5%
R930
61G1206100 3F
RST CHIPR 100 KOHM +-1%
R906
61G1206101
CHIP 100OHM 5% 1/8W
R916
61G1206101
CHIP 100OHM 5% 1/8W
R927
61G1206101
CHIP 100OHM 5% 1/8W
R934
61G1206101
CHIP 100OHM 5% 1/8W
R935
61G1206101
CHIP 100OHM 5% 1/8W
R936
61G1206101
CHIP 100OHM 5% 1/8W
R937
61G1206101
CHIP 100OHM 5% 1/8W
R806
61G1206105
CHIP 1MOHM 5% 1/8W
R818
61G1206150
RST CHIP 15R 1/4W 5%
R819
61G1206150
RST CHIP 15R 1/4W 5%
R808
61G1206204
RST CHIPR 200 KOHM +-5%
R909
61G1206434
RST CHIPR 430 KOHM +-5%
R910
61G1206434
RST CHIPR 430 KOHM +-5%
R931
61G1206434
RST CHIPR 430 KOHM +-5%
R805
61G1206471
RST CHIP 47OR 1/4W 5%
R911
61G1206472
CHIP 4.7KOHM 5% 18W
R914
61G1206519
CHIP resistors 1/3W
R901
61G1206684
CHIPR 680KOHM +-5% 1/8W
R902
61G1206684
CHIPR 680KOHM +-5% 1/8W
R903
61G1206684
CHIPR 680KOHM +-5% 1/8W
R907
61G1206684
CHIPR 680KOHM +-5% 1/8W
R908
61G1206684
CHIPR 680KOHM +-5% 1/8W
R932
61G1206684
CHIPR 680KOHM +-5% 1/8W
C805
65G0805102 32
CHIP 1000PF 50V X7R 0805
C917
65G0805102 32
CHIP 1000PF 50V X7R 0805
C807
65G0805103 32
CHIP 10000 PF 50V X7R 08
C803
65G0805104 22
CHIP 0.1UF 25VX7R 0805
C907
65G0805104 22
CHIP 0.1UF 25VX7R 0805
C910
65G0805104 22
CHIP 0.1UF 25VX7R 0805
47
15” LCD Color Monitor
Sharp LL-153A
C915
65G0805104 22
CHIP 0.1UF 25VX7R 0805
C916
65G0805104 22
CHIP 0.1UF 25VX7R 0805
C801
65G0805104 32
CHIP 0.1UF 50V X7R 0805
C820
65G0805104 32
CHIP 0.1UF 50V X7R 0805
C821
65G0805104 32
CHIP 0.1UF 50V X7R 0805
C822
65G0805104 32
CHIP 0.1UF 50V X7R 0805
C806
65G0805105 22
CHIP 1UF 25V X7R 0805
C918
65G0805105 22
CHIP 1UF 25V X7R 0805
C804
65G0805155 A2
1.5 UF 10V
C802
65G0805221 31
CHIP 220PF 50V NPO
C818
65G0805271 31
CHIP 270pF 50V NPO 0805
C919
65G0805471 21
CHIP 470PF 25V NPO 0805
C812
65G0805472 31
CHIP 4700PF 50V X7R 080
C813
65G0805472 31
CHIP 4700PF 50V X7R 080
C823
65G0805472 31
CHIP 4700PF 50V X7R 080
C824
65G0805472 31
CHIP 4700PF 50V X7R 080
C809
65G0805473 32
SMD 47NF +-10% 50V
C819
65G0805473 32
SMD 47NF +-10% 50V
C810
65G080556131G
MLCC 0805 560PF G 50V NP
C808
65G0805682 32
CHIP 6.8nF 50V X7R 0805
C932
65G1206102 72
CHIP 1000PF 500V X7R
C914
65G1206104 32
CHIP 0.1UF 25V X7R 1206
C931
65G1206222 72
CHIP 2200PF 500V X7R
C933
65G1206222 72
CHIP 2200PF 500V X7R
D802
93G
64 33
BAV99 SOT-23
D801
93G
64 42 PP
DIODE BAV70 SOT-23
D803
93G
64 44
S
CHIP DIODE LL4148WP
D804
93G
64 44
S
CHIP DIODE LL4148WP
D903
93G
64 44
S
CHIP DIODE LL4148WP
ZD904
93G 39S 17
T
RLZ12B LLDS
ZD903
93G 39S 19
T
PTZ7.5B
ZD901
93G 39S 23
T
GLZ22B
ZD801
93G 39S 24
T
RLZ5.6B ROHM
ZD902
93G 39S 25
T
RLZ5.1B ROHM
ZD905
93G 39S 44
T
RLZ18B LLDS
CN901
6G
31500
2.0MM EYELET
C905
6G
31502
1.5MM RIVET
L901
6G
31502
1.5MM RIVET
L902
6G
31502
1.5MM RIVET
PT801
6G
31502
1.5MM RIVET
48
15” LCD Color Monitor
Sharp LL-153A
Q903
6G
31502
1.5MM RIVET
R904
6G
31502
1.5MM RIVET
T901
6G
31502
1.5MM RIVET
IC903
56G 158 10
R928
61G 20022152T
220OHM 1% 1/4W
R822
61G212Y305 KT
MGFR 3M OHM +-5% 1/2W
C930
65G
1500PF +/-10% 1KV Y5P
C922
67G 2152207NT
22UF/50V
F901
84G
55 7W
250V/3.15A FUSE
F902
84G
55 7W
250V/3.15A FUSE
Q903
IC AZ431AZ-AE1 TO-92
1K152 1T
715G2152
R905
T
F
PCB
61G152M10458G
100K OHM 5% 2W
96G
SHRINK TUBE UL/CSA
29
6
51G 200
1
6342
Coolant Oil
57G 667 30
2SK2645-54MR TO-220F
90G6084
HEAT SINK
1
XN01A
AM1G1730
R904
61G
2J68858G
0.68 OHM 5% 2W
96G
29
SHRINK TUBE UL/CSA
CN901
8120
SCREW
6
87G 501 36
S
AC SOCKET
95G 900703
X
WIRE HARNESS
96G
29
6
51G 200
1
90G6084
1
D902
93G
XN01A
AM1G1730
SHRINK TUBE UL/CSA
6342
Coolant Oil
HEAT SINK
60245
51G 200
DIODE SP10150 ITO-220
8120
1
SCREW
6342
Coolant Oil
90G6084800
HEAT SINK
D904
93G
DIODE SP10150 ITO-220
XN01A
AM1G1730
96G
60245
29
8120
SCREW
1
H.S.TUBE
44GP503 1A
1
PAPER PAD-1
44GP503 1A
2
PAPER PAD-2
44GP503 1A
3
PAPER PAD-3
49