Bosch VC7D1305T Specifications

VCM7D130/00T & VC7D1305T | Installation Instructions
EN | 1
IMPORTANT SAFEGUARDS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Install in accordance with the manufacturerís instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this apparatus during lightning storms or when unused
for long periods of time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
The apparatus shall not be exposed to dripping or splashing.
Do not install this equipment in a confined space such as a
bookcase or similar unit.
Bosch Security Systems | 2003-08 | Version 2
Installation Instructions
ENGLISH
EN
VCM7D130/00T & VC7D1305T | Installation Instructions
EN | 2
WARNING
This device is intended for use in public areas only. Surreptitious
recording of oral communications is strictly prohibited by US Federal
law. The manufacturer recommends posting obvious signs to warn
that oral communications are being recorded.
FCC INFORMATION
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into and outlet on a circuit different form
that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for
help.
ATTENTION:
INSTALLATION SHOULD BE PERFORMED BY
QUALIFIED SERVICE PERSONNEL ONLY IN
ACCORDANCE WITH THE NATIONAL ELECTRICAL
CODE OR APPLICABLE LOCAL CODES.
Bosch Security Systems | 2003-08 | Version 2
VCM7D130/00T & VC7D1305T | Installation Instructions
EN | 3
Servicing: Do not attempt to service this product yourself as
removing covers expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
Damage requiring service: Unplug this product from the wall outlet
and referservicing to qualified service personnel.
Replacement Parts: When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
Safety Check: Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
1. INTRODUCTION
This Dome camera is designed for use with Bosch Color Observation
Systems only. It combines a high sensitivity sensor with advanced
digital signal processing, resulting in a high quality Dome camera
with excellent performance even under difficult circumstances.
2. STANDARD PACKAGE INCLUDED
•
•
•
•
Screws x 2pcs
Dome camera x 1pc
Dual twisted pair cable - 15 metres x 1pc
DFU x 1pc
Bosch Security Systems | 2003-08 | Version 2
VCM7D130/00T & VC7D1305T | Installation Instructions
EN | 4
3. INSTALLATION (refer to fig. 1)
To obtain the best results from your new Dome camera, read these
instructions carefully before use. Retain the manual for future
reference. Recommended for indoor Application Only.
This chapter describes the installation of the Dome camera. For more
detailed information about the installation and operation of the
system monitor you should consult the monitor manuals.
Remark: When the system configuration is altered, the system
monitor needs to check and memorise the cameras and accessories
connected to its inputs. This is done automatically when the mains
power is switched on (rear switch).
1
2a
Pull Dome cover
to remove
Mounting screws
2b
3
120º Horz; 120º Vertical;
360º Rotation
Use a screwdriver to
release clip
Fig. 1
Bosch Security Systems | 2003-08 | Version 2
VCM7D130/00T & VC7D1305T | Installation Instructions
EN | 5
When you unpack the Dome camera, the physical default position of
the camera is that the top of the image is correspondant to the camera
'Bosch' logo side.
Before starting the installation, remove the tinted dome by pulling it
off and put it in a safe place to avoid stains and scratches
MOUNTING THE UNIT:
The unit has two cable entries for:
• Cables' route is through the surface like false ceiling or in a
wall (bottom entry)
• Cables' route is on the surface like concrete wall (side entry)
1. Open the mounting plate (1) by pushing the side tab (2b). You
can remove the mounting plate by unhooking from the tab (2a).
2. Using the mounting plate (1) as template, drill holes for camera
mount and cable entry as appropriate.
3. Connect the Dome camera to the system monitor.
4. Locate cable into the appropriate routing clip
5. Fit the camera onto the mounting plate, by hooking the clip (2a),
and then ensuring the tab (2b) clicks into it's location.
6. Connect the system monitor to the mains.
7. Switch on the mains power switch.
8. The monitor will check the system. After a short time the Dome
camera image will appear on the monitor screen.
9. If necessary adjust contrast /brightness and/or color (See the
View Settings menu of the monitor) to optimize the image on the
system monitor.
10. Adjust the viewing direction of the ball camera (3) and ensure
that the picture display on the monitor is level.
11. Click the tinted dome in place and if necessary clean its surface
with a soft cloth.
Bosch Security Systems | 2003-08 | Version 2
VCM7D130/00T & VC7D1305T | Installation Instructions
EN | 6
Note:
The image sensors in modern CCD cameras are highly sensitive and
require special care for proper performance and extended lifetime.
Please follow the guidelines to get optimum results of your camera:
• Do not expose to direct sunlight or bright spotlights in operating
and non-operating conditions.
• Avoid bright lights in the field of view of the camera.
• These bright lights will cause a "smearing" effect, which is
visible as white lines above and below the highlight.
• Bright lights may cause bleaching of the sensor's color filters.
This will be visible as colored spots in the picture and is
irreversible.
Field of view
The figure below shows the Field of view
Bosch Security Systems | 2003-08 | Version 2
VCM7D130/00T & VC7D1305T | Installation Instructions
EN | 7
Dome camera sound on/off
Use the On Screen Display Menus of your system monitor to enable
or disable the built-in Dome camera microphone.
System Cable
For the interconnections between the system monitor and Dome
camera 15m/45ft system cable is supplied.
For an optimum picture and sound quality you should always use 4wire dual twisted-pair cable when extending the connection. The
maximum allowed cable length is 200m/600ft.
Pay attention that the connectors are fixed to the cable corresponding
to the figure.
2 34 5
2 34 5
2
3
2
3
45
4-5
2-3
45
4-5
2-3
CAUTION:
The plugs used for the observation system have the same
dimensions as standard telephone plugs. Never connect a
telephone to the Dome camera or system monitor.
Bosch Security Systems | 2003-08 | Version 2
VCM7D130/00T & VC7D1305T | Installation Instructions
EN | 8
4. TIPS FOR MAINTENANCE
Cleaning
You can clean the outside of the Dome camera with a moist fluff-free
cloth or shammy leather cloth.
When cleaning the Dome camera lens a special cleaning cloth should
be used. Do NOT use cleaning fluids based on alcohol, methylated
spirit, ammonia, etc..
Never touch the glass of the Dome camera lens to prevent its delicate
coating from damaging.
Avoid direct contact with water.
5. SPECIFICATIONS
VCM7D130/00T
VC7D1305T
PAL
NTSC
Integrated lens
Integrated lens
Accessories
The following Dome camera accessories are available:
• Extension system cables (loop resistance max. 16 Ω at 100m).
• Cable extension box for providing additional power and cable
length compensation to the Dome camera at large distances (up
to 300m).
Electro Magnetic Compatibility (EMC)
This equipment complies with the European EMC directive used
standards:
EN50130-4, EN55022
USA standard: FCC part 15, class B
Australia AS/NZS 3548
Bosch Security Systems | 2003-08 | Version 2
VCM7D130/00T & VC7D1305T | Installation Instructions
EN | 9
Safety
according to European standard EN60065 ; USA UL6500
Environmental conditions:
Operating temperature
Non operating temperature
Relative humidity Non-condense
-10ºC +45ºC
-25ºC +70ºC
0% to 95% RH
Input Voltage, via tp-input:
Power consumption, Typical
Weight
Dimensions
24VDC
2.5W
0.31 kg
Ø 115 mm h = 80 mm
This camera can be connected to a previous generation Color
Observation System Monitor at a length of 15 meters. By using an
interface box for every camera the cable length can be up to 200
meters.
If you have any problems, contact your dealer.
Bosch Security Systems | 2003-08 | Version 2