- Computers & electronics
- Audio & home theatre
- Remote controls
- Universal Electronics
- ATLAS CABLE 4-DEVICE
- User's Guide
advertisement
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 1
ATLAS CABLE 4-DEVICE
Universal Remote Control
(Control Remoto Universal)
User’s Guide
(Guía Del Usuario)
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 2
TABLE OF CONTENTS
Introduction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features And Functions
. . . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing Batteries
. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming Device Control
. . . . . . . . . . . . . . . . . . . 8
Programming TV/VCR Combo Control
. . . . . . . . . . . . 10
Searching For Your Code
. . . . . . . . . . . . . . . . . . . . . . 11
Checking The Codes
. . . . . . . . . . . . . . . . . . . . . . . . . 12
Programming ID Lock
. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programming Channel Control Lock
. . . . . . . . . . . . . 14
To De-Activate Channel Control Lock . . . . . . . . . . . . . . . . . 14
To Re-Activate Channel Control Lock . . . . . . . . . . . . . . . . . 14
Using The Master Power Key
. . . . . . . . . . . . . . . . . . . 15
To Program The Master Power Key . . . . . . . . . . . . . . . . . . . 15
To Clear The Master Power Key. . . . . . . . . . . . . . . . . . . . . . 15
To Operate The Master Power Key. . . . . . . . . . . . . . . . . . . . 15
Re-Assigning Device Keys
. . . . . . . . . . . . . . . . . . . . 16
Using Macros
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Example – Programming A Favorite Channel . . . . . . . . . . 17
To Clear A Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Changing Volume Lock
. . . . . . . . . . . . . . . . . . . . . . . 18
To Unlock Volume Control For A Single Device
(Individual Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . 18
To Unlock All Volume Control
(Global Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
To Lock Volume Control To One Mode
(Global Volume Lock). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Instructions To The User
. . . . . . . . . . . . . . . . . . . . . . . . . 21
Additional Information
. . . . . . . . . . . . . . . . . . . . . . . . 21
Guía Del Usuario. . . . . . . . . . . . . . . . . . . . . . . . . .
22
Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . .
42
Setup Codes for Audio Amplifiers. . . . . . . . . . . . . . . . . . . . 42
Setup Codes for Audio Receivers . . . . . . . . . . . . . . . . . . . . 42
Setup Codes for Cable Converters . . . . . . . . . . . . . . . . . . . 43
Setup Codes for DVD Players . . . . . . . . . . . . . . . . . . . . . . . 43
Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Setup Codes for TV/VCR Combos . . . . . . . . . . . . . . . . . . . . 48
Setup Codes for VCRs and PVRs . . . . . . . . . . . . . . . . . . . . 48
2
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 3
INTRODUCTION
The Atlas Cable 4-Device Universal Remote Control by
Universal Electronics is our latest generation universal remote control. Its sophisticated technology allows you to consolidate all of your original home entertainment remote controls into one easy-to-use product. Moreover, it’s packed with advanced features such as:
• Preprogrammed to operate the cable converter supplied by your cable system provider
• Master Power key for master on/off control of all of your equipment with a single keystroke
• Macro key for instant tune-in of favorite channels
• Cable ID Lock to lock your remote control for use only with the cable converter
• Channel Lock to lock channel selection only to the cable converter
• Volume Lock to lock volume controls to one mode or individual modes
• Device Key Re-Assignment to remotely control a second (duplicate) device
• Color-coded keys to quickly locate popular functions
• Code library for popular video and audio devices
Before using the product, you will need to program it to operate the specific home entertainment devices you wish to control. Follow the instructions detailed in this manual to set up your unit and then start enjoying your new remote control.
3
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 4
FEATURES AND FUNCTIONS
Use the illustration below to locate features on the Atlas
Universal Remote Control and then study the Key Charts (on the next two pages) to learn how they function.
4
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 5
Key Charts
or or
Use SETUP for all programming sequences.
Press POWER once to turn on or off a home entertainment device.
Press AUD, VCR, TV, or CBL once to select a home entertainment device to control. Each device key has an embedded LED (red light) that blinks upon selection and indicates that the remote control is working and is sending signals.
Use GUIDE to display the program guide.
Press MENU once to display the available interactive services.
Press LOCK once to lock or unlock channels for parental control of viewing.
Use INFO to display the current channel and program information.
Use SETTINGS/MENU to access additional cable features (see your cable converter’s manual).
Use PAGE+ (or PAGE-) to page up
(or page down) through menu screens and the program guide.
Use the Cursor keys to move the cursor in the program guide and menu screens and to navigate within the interactive service.
Use SELECT to choose options, PPV events, and to tune programs from the program guide.
continued on the next page...
5
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 6
FEATURES AND FUNCTIONS
Key Charts (continued)
After programming, press MACRO once to run a macro (see Using
Macros on page 17).
Use EXIT to exit out of your cable converter’s menu and guide.
Use A, B, or C to access additional cable features (see your cable converter’s manual).
Use DAY+ (or DAY-) to move a day forward (or back) on your cable converter’s program guide.
Use VOL+ (or VOL-) to raise (or lower) the audio volume.
Press LAST once to recall the last channel. For PVRs, use LAST to select live or recorded video.
Use FAV to cycle through your favorite channels stored in your cable converter.
Press MUTE once to turn the sound off or on.
Use CH+ (or CH-) to select the next higher (or lower) channel.
For DVD players, use these keys to skip forward (or reverse) through chapters. For amplifiers/receivers, use these keys to select the next higher (or lower) preset station.
Use the keypad (1~9, 0, , and ) to directly select channels (e.g., 09).
Press ENTER once after entering channel numbers on some TVs.
For amplifiers/receivers, use the keypad to select inputs 1 through 10.
Use BYPASS to view other video sources (A or B) instead of cable.
6
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 7
Use TV/VCR to switch the TV input to view video or TV programs. For amplifiers/receivers, use this key to select input or output.
In all modes except CBL, use these keys to control a VCR, DVD player, or PVR. To record in the VCR mode, press REC twice.
In the CBL mode, use these keys except REC to control VOD (Video
On Demand), if available.
INSTALLING BATTERIES
❶
❷
1.
❸
On the back of the remote control, push the tab and lift off the battery cover.
continued on next page...
7
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 8
INSTALLING BATTERIES (continued)
2.
3.
Obtain two (2) new AA alkaline batteries.
Match the + and – marks with those in the battery case, then insert the new batteries.
Align the cover’s keys with the case’s holes and press the cover back into place. The tab should click when the cover is locked.
4.
Test the unit by pressing POWER and any mode key (e.g., TV). If batteries are inserted correctly, the selected mode key will blink once.
NOTE: When batteries need replacement, the remote control will cease to operate. Replace the batteries and the unit will be restored to its full functionality, complete with your favorite settings.
PROGRAMMING DEVICE CONTROL
The Atlas Universal Remote Control is preprogrammed to operate the cable converter provided by your cable system, an RCA TV, an RCA VCR, and a Pioneer audio receiver.
To control devices other than the default brands, perform the following steps; otherwise skip this section:
NOTES: To control a DVD player, program the VCR key. To control a PVR, program the VCR key. To control a stereo amplifier or receiver, program the AUD key. For TV/VCR Combo control, skip this section and perform the instructions on page 10.
If you have another brand of cable converter and interactive service you would like to control, you’ll first need to unlock the cable ID Lock before changing the converter code – see
“Programming ID Lock” on page 13.
1.
Turn on a device and, if applicable, insert video media, (e.g., cassette or disc).
2.
3.
NOTE: Please read steps 2 to 4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.
On the remote control, press a device key once
(e.g., AUD, VCR, TV, or CBL). Press and hold
SETUP until the selected mode key blinks twice, then release SETUP.
Use the Manufacturer’s Codes (starting on page 42) to locate the the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the selected mode key will blink twice.
8
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 9
4.
5.
TV
CBL
NOTE: If the selected mode key emits a long blink, the code is invalid. Repeat steps 2 and 3 and try entering the same code again.
Aim the remote control at the device and press
POWER once. The device should turn off. If it does not, repeat steps 2 to 3, trying each code for your brand until you find one that works.
If it still does not work, try searching for the code (see Searching For Your Code on page 11).
NOTE: If the device does not have a POWER key, press the (Play) key.
Repeat steps 1 through 4 for each device you want the the remote control to control. For future reference, write down each working device code in the following boxes:
AUD
Audio Device ____________________
VCR
9
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 10
PROGRAMMING TV/VCR COMBO CONTROL
If you own a TV/VCR Combo, perform the following instructions to control this device:
1.
Turn on your TV/VCR Combo and insert a video cassette.
2.
3.
On the remote control, press VCR once.
Press and hold SETUP until the VCR key blinks twice, then release SETUP.
Use the Setup Codes For TV/VCR Combos (on page 48) to locate the brand name and then enter the first four-digit code for your TV/VCR
Combo. If you perform this procedure correctly, the VCR key will blink twice.
4.
5.
NOTE: If the VCR key did not blink twice after entering the code’s last digit, then repeat steps 2 to 3 and try entering the same code again.
If you’ve located a TV/VCR setup code that works your TV/VCR Combo and a separate TV code is also listed, you’ll need to program this code into the remote control to access volume control (see Programming Device Control on page 8).
Aim the remote control at your TV/VCR
Combo and press POWER once. The device should turn off. If it does not respond, repeat steps 2 and 3 (starting on the previous page), trying each code listed for your brand until you find one that works. If it still does not work, try searching for the code (see Searching For Your
Code on the next page).
For future reference, write down each working device code in the boxes below:
TV/VCR
TV (if used)
10
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 11
SEARCHING FOR YOUR CODE
1.
2.
If your home entertainment device does not respond to the Atlas Universal Remote Control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.
NOTE: To search for a code in the CBL mode, you’ll first need to unlock the cable ID Lock – see “Programming ID Lock” on page 13.
For example, to search for a code for your TV:
Turn on your TV.
On the remote control, press TV once.
Then press and hold SETUP until the
TV key blinks twice, then release SETUP.
3.
Enter 9 - 9 - 1. The TV key will blink twice.
5.
6.
4.
Aim the remote control at the the TV and slowly alternate between pressing POWER and TV.
Stop when the TV turns off.
NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first.
Press SETUP once to lock in the code. The TV key will blink twice.
To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate key (i.e., AUD, VCR, or CBL) for the (Audio,VCR, or Cable) device you are searching for.
11
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 12
CHECKING THE CODES
If you have set up the Atlas Universal Remote Control using the Searching For Your Code procedure (on the previous page), you may need to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV:
1.
On the remote control, press TV once.
Then press and hold SETUP until the
TV key blinks twice, then release SETUP.
2.
Enter 9 - 9 - 0. The TV key will blink twice.
3.
4.
5.
To view the code for the first digit, press 1 once.
Wait 3 seconds and count the number of times the TV key blinks (e.g., 3 blinks = 3) and write down the number in the leftmost TV Code box
(see below).
NOTE: If a code digit is “0”, the selected mode key will not blink.
Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. Finish writing down the code in the TV Code boxes below.
To check for other device codes, repeat steps 1 through 4, but substitute the appropriate key
(i.e., AUD, VCR, or CBL) for the (Audio,VCR, or
Cable) device you are checking.Write down the codes in the appropriate boxes below.
AUD
Audio Device ____________________
VCR
TV
CBL
12
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 13
PROGRAMMING ID LOCK
1.
2.
The Atlas Universal Remote Control is preprogrammed and locked at the factory to operate a Scientific Atlanta cable converter.
However, if you have another brand or model of cable converter and interactive service that you would like to control, then you’ll need to perform the following steps to unlock the cable ID Lock, enter in a new manufacturer’s code, and lock the ID Lock again.
Turn on the cable converter.
On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
3.
Enter 9 - 8 - 2. The CBL key will blink four times.
4.
5.
6.
Perform the instructions in Programming
Device Control on page 8 to program device control for the desired cable converter and interactive service. Upon completion, perform the remaining steps (5 and 6 on this page) to again lock the ID lock.
On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
Enter 9 - 8 - 2. The CBL key will blink twice.
13
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 14
PROGRAMMING CHANNEL CONTROL LOCK
By default, the remote control’s channel-control capabilities are locked to the cable converter. The affected keys* are
0 ~ 9, CH+, CH-, ENTER, and LAST. This will guarantee that you do not inadvertently change a channel on your TV or
VCR. However, you can de-activate this feature to allow full access to these keys in the TV and VCR modes.
*NOTE: This feature does not affect the AUD mode.
To De-Activate Channel Control Lock:
1.
On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
2.
Enter 9 -7- 3. The CBL key will blink two times.
3.
Press CH- once. The CBL key will blink four times.
4.
Now, the remote control will provide TV and
VCR channel-control capabilities while in the
TV or VCR mode.
To Re-Activate Channel Control Lock:
1.
On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
2.
Enter 9 -7- 3. The CBL key will blink two times.
3.
4.
Press CH+ once. The CBL key will blink twice.
Now, regardless of what mode you select
(i.e., TV, VCR, or CBL), only the channel control capability of your cable converter will be accessible.
14
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 15
USING THE MASTER POWER KEY
The Atlas Universal Remote Control has a unique feature that allows you to sequentially turn on or off all of your home entertainment devices with a single key press.
NOTE: MASTER POWER only works in the CBL mode. If it is not programmed, only the cable converter will turn on or off. In any other mode, pressing MASTER POWER once will turn on or off the selected device.
To Program The Master Power Key:
1.
On the remote control, press and hold SETUP until the last-selected device key blinks twice, then release SETUP.
2.
Enter 9 - 9 - 5. The last-selected device key will blink twice. Then press POWER once.
3.
For the first device you want in the power on sequence, press a device key (e.g., CBL) once and then press POWER once.
4.
5.
Repeat step 3 up to three more times to add the second, third, and fourth device, as desired.
To save the settings and exit the program, press
CBL once. Next, press and hold SETUP until the
CBL key blinks twice, then release SETUP.
To Clear The Master Power Key:
1.
Perform steps 1 and 2 in the above section.
2.
To clear the settings and exit the program, press and hold SETUP until the CBL key blinks twice, then release SETUP.
To Operate The Master Power Key:
1.
After programming, point the remote control at the devices. Press CBL once.
2.
3.
Press MASTER POWER once to sequentially turn on or off all home entertainment devices.
You will see the devices turn on or off according to the programmed sequence.
15
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 16
RE-ASSIGNING DEVICE KEYS
The Atlas Universal Remote Control can be set up to control a second TV or VCR, or any combination of up to four home entertainment devices. For example, to have the unit control a TV, a Cable Converter, and two
VCRs, you will need to re-assign the unused AUD key to operate the second VCR as follows:
1.
On the remote control, press VCR once.
Then press and hold SETUP until the
VCR key blinks twice, then release SETUP.
2.
Enter 9 - 9 - 2. The VCR key will blink twice.
3.
4.
Press VCR once, then press AUD once. The
AUD key will blink twice.
The AUD key is now ready to be programmed for your second VCR. See Programming Device
Control on page 8.
To re-assign other device keys, repeat steps 1 to 4 and substitute the key sequence using the following chart:
To Re-Assign Perform Key Sequence
TV as 2nd VCR key: TV - SETUP - 9 - 9 - 2 - VCR - TV
TV as 2nd Audio key: TV - SETUP - 9 - 9 - 2 - AUD - TV
TV as 2nd Cable key: TV - SETUP - 9 - 9 - 2 - CBL - TV
TV back to TV: TV - SETUP - 9 - 9 - 2 - TV - TV
VCR as 2nd TV key: VCR - SETUP - 9 - 9 - 2 - TV - VCR
VCR as 2nd Audio key: VCR - SETUP - 9 - 9 - 2- AUD - VCR
VCR as 2nd Cable key: VCR - SETUP - 9 - 9 - 2 - CBL - VCR
VCR back to VCR: VCR - SETUP - 9 - 9 - 2 - VCR - VCR
AUD as 2nd TV key: AUD - SETUP - 9 - 9 - 2 - TV - AUD
AUD as 2nd Cable key: AUD - SETUP - 9 - 9 - 2 - CBL - AUD
AUD back to AUD: AUD - SETUP - 9 - 9 - 2 - AUD - AUD
Upon completion of a re-assignment, the selected mode key will blink twice to confirm your selection. Then, you’ll need to program device control (see Programming Device
Control on page 8).
16
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 17
USING MACROS
With programming, the MACRO key on your Atlas Universal
Remote Control can be setup to perform repetitive, timeconsuming operations through the press of a single key.
A macro can be used to control a home theater operation, to set a favorite channel, or for other multiple functions you would like to control with one key press (see examples below). Moreover, the MACRO key can hold up to three macros with up to 15 key presses each. The macros are then activated, in the order they were stored, each time you press this key.
NOTE: If three macros are stored, programming a new macro will erase the first original macro. Thereafter, each new macro will overwrite the next original macro.
Example – Programming A Favorite Channel
With so many channels available through your cable provider, you can program a macro that directly selects a favorite channel with one key press. For example, let’s assume your favorite cable programs are on channel 71.
Use the following instructions to program a macro for direct access of this channel:
1.
2.
On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
Enter 9 - 9 - 5. The CBL key will blink twice.
3.
4.
5.
6.
Press MACRO once.
Press CBL once.
Enter the channel number, 7 -1.
NOTE: If you have access to over 100 channels, enter
0-7-1. Moreover, if the original remote control required pressing an Enter key to change the channel, also press the ENTER key after the channel number
(e.g., 0-7-1-ENTER).
Press and hold SETUP until the CBL key blinks twice, then release SETUP.
Now when you press MACRO, you will instantly see the cable converter tune to channel 71.
NOTE: To store three channels onto the MACRO key, repeat the six steps above two more times, substituting a new favorite channel in step 5 (e.g., 7 - 2 for channel 72).
17
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 18
3.
4.
USING MACROS (continued)
To Clear A Macro:
1.
On the remote control, press and hold SETUP until the last-selected device key blinks twice, then release SETUP.
2.
Enter 9 - 9 - 5. The last-selected device key will blink twice.
Press MACRO once.
Press and hold SETUP until the last-selected device key blinks twice, then release SETUP.
NOTE: A macro will be cleared in the order it was originally stored.
CHANGING VOLUME LOCK
On the Atlas Universal Remote Control, Global Volume Lock is set to TV, so you can control TV volume while in the TV,
VCR, or Cable mode. If desired, you can still perform
Individual Volume Unlock on a selected device to set its volume control for independent operation.
NOTE: If you lock the volume controls to the AUDIO mode, you will still have control of the audio device’s volume in all other modes
(i.e., TV, VCR, and CBL).
To Unlock Volume Control For A Single Device
(Individual Volume Unlock):
1.
Assuming Global Volume Lock is active, select a mode on the remote control that you want to unlock (e.g.,CBL) and press it once. Next, press and hold SETUP until the device key blinks twice, then release SETUP.
2.
Enter 9 - 9 - 3. The last-selected device key will blink twice.
3.
Press VOL– once. The selected device key will blink four times.
18
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 19
4.
5.
Now, after you select a device that has volume unlocked (e.g., CBL), pressing VOL+, VOL–, or
MUTE, will control the device’s volume only in its own mode.
To Unlock All Volume Control
(Global Volume Unlock):
NOTE: Performing these instructions will set independent volume control for all programmed devices (e.g., TV volume control in
TV mode, VCR volume in VCR mode, etc.).
1.
On the remote control, press and hold SETUP until the last-selected device key blinks twice, then release SETUP.
2.
Repeat steps 1 through 3 (of this section) for each device you want volume to be unlocked.
Enter 9 - 9 - 3. The last-selected device key will blink twice.
3.
Press VOL+ once. The last-selected device key will blink four times.
To Lock Volume Control To One Mode
(Global Volume Lock):
NOTE: If you lock the volume controls to the AUDIO mode, you will still have control of the audio device’s volume in all other modes
(i.e., TV, VCR, and CBL).
1.
On the remote control, press and hold SETUP until the last-selected device key blinks twice, then release SETUP.
2.
Enter 9 - 9 - 3. The last-selected device key will blink twice.
3.
4.
Select a mode (e.g., TV) where you want to globally lock the volume controls. The selected device key will blink twice.
Now, when you press VOL+, VOL–, or MUTE, the volume of the selected device (e.g., TV) can be controlled regardless of mode.
19
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 20
TROUBLESHOOTING
PROBLEM: Mode key does not blink when you press a key.
SOLUTION: Replace the batteries with two (2) new AA alkaline batteries (see page 7).
PROBLEM: Mode key blinks when you press a key, but home entertainment device does not respond.
SOLUTION: Make sure you are aiming the remote control at your home entertainment device and that you are within 15 feet of the device you are trying to control.
PROBLEM: The remote control does not control home entertainment devices or commands are not performing properly.
SOLUTION: Try all listed codes for the device brand being set up. Make sure all devices can be operated with an infrared remote control.
PROBLEM: TV/VCR combo does not respond properly.
SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation (see page 10).
PROBLEM: No volume on a second TV.
SOLUTION: Follow instructions in Changing Volume Lock
(see page 18).
PROBLEM: CH+ , CH – , and LAST do not work for your
RCA TV.
SOLUTION: Due to RCA design (1983-1987), only the original remote control will operate these functions.
PROBLEM: Changing channels does not work properly.
SOLUTION: If original remote control required pressing
ENTER to change channels, press ENTER on the remote control after entering a channel number.
PROBLEM: Tried “Search Method” and still could not find a working code.
SOLUTION: Try the “Search Method” again after clearing out the device key as follows: Press and hold SETUP until mode key blinks twice, then release. Next enter 9 - 9 - 2. Then press and release the mode key to be cleared twice.
PROBLEM: Remote control does not turn on Sony or Sharp
TV/VCR Combo.
SOLUTION: For power on, these products require programming TV codes on the remote control. For Sony, use TV code 0000 and VCR code 0032. For Sharp, use TV code 0093 and VCR code 0048.
20
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 21
INSTRUCTIONS TO THE USER
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been verified to comply with the limits for a class B computing device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
ADDITIONAL INFORMATION
This product does not have any user-serviceable parts. Opening the case, except for the battery cover, may cause permanent damage to your Atlas Universal Remote Control.
For help via the Internet, visit us at: www.urcsupport.com
For help via e-mail, contact us at: [email protected]
Copyright 2003 by Universal Electronics Inc. No part of this publication may be reproduced, transmitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without prior written permission of
Universal Electronics Inc.
M4030AS 05/03
21
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 22
TABLA DE CONTENIDOS
Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Características Y Funciones . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cuadros De Teclas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Instalación De Las Baterías . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Programación Del Control De Dispositivos . . . . . . . . . . . . . . 28
Programación De Control De Combos TV/VCR . . . . . . . . . . . 30
Búsqueda De Su Código
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Comprobación De Los Códigos . . . . . . . . . . . . . . . . . . . . . . . . 32
Programación Del Bloqueo De ID . . . . . . . . . . . . . . . . . . . . . . . 33
Programación Del Bloqueo Del Control De Canal . . . . . . . . 34
Desactivación Del Bloqueo Del Control De Canal . . . . . . . . . . . . . . 34
Reactivación Del Bloqueo Del Control De Canal . . . . . . . . . . . . . . 34
Utilización Del Botón De Encendido Principal . . . . . . . . . . 35
Programación Del Botón De Encendido Principal . . . . . . . . . . . . . 35
Restablecimiento Del Botón De Encendido Principal . . . . . . . . . . . 35
Utilización Del Botón De Encendido Principal . . . . . . . . . . . . . . . . 35
Reasignación De Teclas De Dispositivos . . . . . . . . . . . . . . . . 36
Utilización De Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Ejemplo – Programación De Su Canal Favorito . . . . . . . . . . . . . . . 37
Eliminación De Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cambio Del Bloqueo De Volumen . . . . . . . . . . . . . . . . . . . . . . . 38
Desbloqueo Del Control De Volumen Para Un Sólo Dispositivo
(Desbloqueo De Volumen Individual. . . . . . . . . . . . . . . . . . . . . . . . 38
Desbloqueo De Todos Los Controles De Volumen
(Desbloqueo De Volumen Total) . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Bloqueo De Volumen En Un Modo
(Bloqueo De Volumen Total) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Resolución De Problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Instrucciones Al Usuario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Información Adicional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Códigos Del Fabricante
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Códigos De Configuración Para Amplificadores De Audio. . . . . . . . 42
Códigos De Configuración Para Receptores De Audio. . . . . . . . . . . 42
Códigos De Configuración Para Convertidores De Cable . . . . . . . . 43
Códigos De Configuración Para Reproductores De DVD . . . . . . . . . 43
Códigos De Configuración Para TVs. . . . . . . . . . . . . . . . . . . . . . . . 44
Códigos De Configuración Para Combos TV/VCRs . . . . . . . . . . . . . 48
Códigos De Configuración Para VCRs Y PVRs . . . . . . . . . . . . . . . . 48
22
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 23
INTRODUCCIÓN
El control remoto universal para cable y 4-Dispositivos Atlas de
Universal Electronics es nuestro control remoto universal de
última generación. Su sofisticada tecnología le permitirá reunir todos los controles remotos de sus dispositivos de entretenimiento doméstico en un único aparato de fácil manejo.
Además, incluye funciones avanzadas como:
• Preprogramación para funcionar con el convertidor de cable suministrado por su proveedor de cable.
• Botón De Encendido Principal para encender y apagar todos sus equipos con un solo botón.
• Botón De Macro para la sintonización instantánea de sus canales favoritos.
• Bloqueo De ID De Cable para utilizar su control remoto
únicamente con el convertidor de cable.
• Bloqueo De Canal para bloquear la selección de canal sólo en el convertidor de cable
• Bloqueo De Volumen para bloquear el control de volumen en uno o más modos.
• Reasignación De Dotones De Dispositivos para el control remoto de un segundo servicio (duplicado)
• Teclas de colores para ubicar rápidamente los funciones más utilizadas
• Biblioteca de códigos para dispositivos de audio y video
Antes de comenzar a utilizar el producto, deberá programarlo para que funcione con los dispositivos de entretenimiento doméstico con los que usted desee utilizar el control. Siga las instrucciones que se detallan en este manual para configurar su unidad y comenzar a disfrutar de su nuevo control remoto.
23
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 24
CARACTERÍSTICAS Y FUNCIONES
Refiérase a la ilustración mostrada más adelante para ubicar las funciones del Control Remoto Universal Atlas y estudie a continuación los Cuadros De Teclas (en las dos páginas siguientes) para aprender a usar cada una de ellas.
24
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 25
Cuadros De Teclas
Use SETUP para todas las secuencias de programación.
o o
Presione POWER una vez para encender o apagar un dispositivo de entretenimiento doméstico.
Presione AUD, VCR, TV, o CBL para seleccionar el dispositivo que desea controlar. Cada tecla cuenta con un LED
(luz roja) que parpadea cuando ésta es usada e indica que el control remoto está funcionando y enviando señales.
Use GUIDE para mostrar la guía de programas.
Presione MENU una vez para mostrar los servicios interactivos disponibles.
Presione LOCK una vez para bloquear o desbloquear canales (control parental).
Use INFO para mostrar la información sobre el canal y el programa actual.
Use SETTINGS/MENU para acceder a funciones adicionales de cable
(consulte el manual de su convertidor de cable).
Use PAGE+ (o PAGE-) para desplazarse por las pantallas del menú y la guía de programa.
Use las Teclas De Cursor para mover el cursor dentro de la guía de programas y las pantallas de menú y para navegar dentro del servicio interactivo.
Utilice SELECT para elegir opciones, eventos PPV, y para sintonizar programas de la guía de programas.
Después de la programación, presione
MACRO para ejecutar un macro (ver
Utilización De Macros en la página 37).
Use EXIT para salir del menú y la guía del convertidor de cable.
Use A, B, o C para acceder a funciones adicionales de cable (consulte el manual de su convertidor de cable).
continúa en la página siguiente…
25
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 26
CARACTERÍSTICAS Y FUNCIONES
Cuadros De Teclas (continuación)
Use DAY+ (o DAY) para avanzar o retroceder un día en su guía de programas del convertidor de cable.
Use VOL+ (or VOL-) para subir o bajar el volumen del sonido.
Presione LAST una vez para volver al
último canal. Para PVRs, use LAST para seleccionar vídeo en directo o grabado.
Use FAV para rotar por sus canales favoritos almacenados en el convertidor de cable.
Presione MUTE una vez para anular o restablecer el sonido.
Use CH+ (o CH-) para seleccionar el canal siguiente (o anterior).
Para reproductores de DVD, utilice estas teclas para avanzar o retroceder capítulos. Para amplificadores y receptores, utilice estas teclas para seleccionar la anterior o siguiente emisora preestablecida.
Use el teclado numérico (1~9, 0, , y
) para seleccionar directamente los canales (p. ej., 09).
Presione ENTER después de introducir los números del canal en algunas marcas de TV.
Para amplificadores/receptores, use el teclado numérico para seleccionar entradas de 1 a 10.
Use BYPASS para ver otras fuentes de vídeo (A o B) en lugar del cable.
Use TV/VCR para alternar la entrada de TV entre vídeo o programas de televisión. Utilice esta tecla en amplificadores/receptores para seleccionar entrada o salida.
26
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 27
En todos los modos excepto CBL,use estas teclas para controlar un VCR, reproductor de DVD o PVR.Para grabar en el modo VCR, presione REC dos veces.
Use estas teclas (excepto REC) en el modo CBL para controlar el VOD
(Video On Demand), en los casos en que esté disponible.
INSTALACIÓN DE LAS BATERÍAS
❶
❷
1.
2.
❸
En el reverso del control remoto, presione la pestaña y levante la tapa de las baterías.
Adquiera dos (2) baterías alcalinas AA nuevas. Haga coincidir las marcas + y – de las baterías con las de su compartimento e insertelas.
continúa en la página siguiente…
27
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 28
INSTALACIÓN DE BATERÍAS (continuación)
3.
Alinee las teclas de la cubierta con los orificios de la carcasa y empuje la cubierta anterior hasta que quede en su sitio. La pestaña hará clic cuando la cubierta esté ajustada.
4.
Pruebe la unidad presionando la tecla POWER o la de modo (p. ej., TV ). Si las baterías han sido introducidas correctamente, la tecla de modo seleccionada parpadeará una vez.
NOTA: El control remoto dejará de funcionar cuando las baterías tengan que ser sustituidas. Sustituya las baterías y la unidad recuperará todas sus funciones y su configuración personal.
PROGRAMACIÓN DE CONTROL DE DISPOSITIVOS
El Control remoto universal Atlas está preprogramado para funcionar con su convertidor de cable, con una TV RCA, con un
VCR RCA, y con un receptor de audio Pioneer. Para controlar dispositivos de marcas diferentes a las predeterminadas, siga los siguientes pasos; en caso contrario, ignore esta sección.
NOTAS: Para controlar un PVR, programe la tecla VCR. Para controlar un
PVR, programe la tecla VCR. Para controlar un amplificador o receptor estéreo, programe la tecla AUD. Para controlar un Combo TV/VCR, ignore esta sección y siga las instrucciones detalladas en la página siguiente.
Si posee otra marca de convertidor de cable o servicio interactivo con la que desea utilizar el control, deberá en primer lugar desactivar el Bloqueo
De ID De Cable antes de cambiar el código de convertidor. Consulte
“Programación Del Bloqueo De ID" en la página 33.
1.
Encienda un dispositivo e introduzca, en su caso, un medio audiovisual (p. ej., cassette o video).
2.
NOTA: Por favor, lea íntegramente los pasos del 2 al 4 antes de empezar. Subraye o anote los códigos y dispositivo que desea programar antes de seguir con el paso número 2.
En el control remoto, presione una de las teclas de dispositivo una vez (ej., AUD, VCR, TV, o CBL).
Presione y mantenga presionado SETUP hasta que el modo seleccionado parpadee dos veces.
A continuación, suelte el botón.
3.
Utilice los Códigos Del Fabricante (a partir de la página 42) para determinar el tipo de dispositivo y marca y a continuación introduzca el primer dígito del código de cuatro dígitos de su dispositivo. La tecla del modo seleccionado parpadeará dos veces para indicarle que es correcto.
NOTA: Si la tecla de modo seleccionada emite una luz prolongada, el código es inválido. Repita los pasos 2 y 3 e intente introducir el mismo código de nuevo.
28
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 29
4.
5.
Dirija el control remoto hacia el dispositivo y presione POWER una vez. El dispositivo debería apagarse. Si no ocurre así, repita los pasos 2 y 3, inténtelo con cada código de su marca hasta encontrar uno que funcione. Si aún así no funciona, intente buscar el código (consulte Búsqueda De Su
Código en la página 31).
NOTA: Si el dispositivo no tiene botón POWER, presione el botón (Play).
Repita los pasos del 1 al 4 para cada uno de los dispositivos con los que desea utilizar el control remoto.Anote los códigos correctos de cada dispositivo en los siguientes espacios para referencias futuras:
AUD
Dispositivo Audio ___________________
VCR
TV
CBL
29
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 30
PROGRAMACIÓN DEL CONTROL
DEL COMBO TV/VCR
Si usted posee un combo TV/VCR, siga las siguientes instrucciones para utilizar el control con este dispositivo:
1.
Encienda su combo TV/VCR e introduzca una cinta de video.
2.
3.
4.
En el control remoto, presione VCR una vez. Presione y mantenga presionado SETUP hasta que la tecla
VCR parpadee dos veces.A continuación, suelte el botón SETUP.
Utilice los Códigos De Configuración Para Combos
TV/VCR (en lapágina 48) para ubicar el nombre de la marca y después introducir el primer código de cuatro dígitos para su combo TV/VCR. Si ha seguido este procedimiento correctamente, la tecla
VCR parpadeará dos veces.
NOTA: Si la tecla VCR no parpadeó dos veces tras introducir el último dígito del código, repita los pasos del
2 al 3 e intente introducir el mismo código de nuevo.
Si localiza un código de configuración que funcione con su combo TV/VCR y encuentra también un código independiente para TV, deberá programar este código en el control remoto para acceder al control de volumen (consulte Programación De Control
De Dispositivos en la página 28).
Dirija el control remoto hacia su combo TV/VCR y presione POWER una vez. El dispositivo debería apagarse. Si no ocurre así, repita los pasos 2 y 3, inténtelo con cada código enumerado para su marca hasta encontrar uno que funcione. Si aún así no funciona, intente buscar el código (consulte Búsqueda De Su
Código en la página 31).
5.
Anote los códigos correctos de cada dispositivo en los siguientes espacios para referencias futuras:
TV/VCR
TV
(si se usó)
30
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 31
BÚSQUEDA DE SU CÓDIGO
Si su dispositivo de entretenimiento doméstico no responde al
Control Remoto Universal Atlas después de haber probado todos los códigos enumerados para su marca, o si su marca no aparece, intente la búsqueda de su código.
NOTA: Para buscar un código en el modo CBL, deberá en primer lugar desbloquear el Bloqueo De ID dDe Cable (ver “Programación Del Bloqueo
De ID” en la página 33).
Por ejemplo, para buscar un código para su TV:
1.
Encienda su TV.
2.
En el control remoto, presione TV una vez. Presione y mantenga presionado SETUP hasta que la tecla
TV parpadee dos veces. A continuación, suelte el botón SETUP.
3.
Presione 9 - 9 - 1. La tecla TV parpadeará dos veces.
4.
5.
6.
Dirija el control a la TV y lentamente alterne entre las teclas de POWER y TV. Deténgase cuando la TV se apague.
NOTA: En el modo de búsqueda, el control remoto enviará códigos infrarrojos desde su biblioteca al dispositivo seleccionado, comenzando con el código más utilizado.
Presione SETUP una vez para bloquear el código.
La tecla TV parpadeará dos veces.
Para buscar los códigos del resto de sus dispositivos, repita los pasos del 1 al 5, pero presione la tecla pertinente (p. ej., AUD, VCR, o CBL) para el dispositivo que esté buscando.
31
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 32
COMPROBACIÓN DE LOS CÓDIGOS
Si usted ha configurado el Control Remoto Universal Atlas siguiendo el procedimiento Búsqueda De Su Código (página anterior), es probable que deba averiguar qué código de cuatro dígitos funciona con su dispositivo. Por ejemplo, para averiguar qué código funciona con su TV:
1.
En el control remoto, presione TV una vez. Presione y mantenga presionado SETUP hasta que la tecla
TV parpadee dos veces. A continuación, suelte el botón SETUP.
2.
Presione 9 - 9 - 0. La tecla TV parpadeará dos veces.
3.
4.
5.
Para ver el primer dígito del código, presione 1 una vez. Espere 3 segundos y cuente el número de veces que parpadea la tecla TV (p. ej., 3 parpadeos = 3) y anote el número en el primer espacio de los destinados al código de su TV (ver más adelante).
NOTA: Si el dígito del código es “0”, la tecla de modo seleccionada no parpadeará.
Repita el paso 3 tres veces más para los dígitos restantes. Utilice 2 para el segundo dígito, 3 para el tercer dígito, y 4 para el cuarto. Termine de escribir el código en los espacios destinados al código de su
TV más adelante.
Para buscar los códigos del resto de sus dispositivos, repita los pasos del 1 al 4, pero presione la tecla pertinente (p. ej., AUD, VCR, o CBL) para el dispositivo que esté buscando.Anote los códigos en los cuadrados adecuados abajo:
AUD
Dispositivo Audio ___________________
VCR
TV
CBL
32
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 33
PROGRAMACIÓN DEL BLOQUEO DE ID
El Control Remoto Universal Atlas está preprogramado y bloqueado de fábrica para funcionar con el convertidor de cable
Scientific Atlanta.
Sin embargo, si usted tiene otra marca o modelo de convertidor de cable y servicio interactivo con los que le gustaría utilizar su control remoto, deberá entonces seguir los siguientes pasos para desbloquear el ID de cable, introducir un nuevo código de fabricante y bloquear el ID de nuevo.
1.
Encienda el convertidor de cable.
2.
En el control remoto, presione CBL una vez. Presione y mantenga presionado SETUP hasta que la tecla
CBL parpadee dos veces.A continuación, suelte el botón SETUP.
3.
Presione 9 - 8 - 2. La tecla CBL parpadeará cuatro veces.
4.
5.
6.
Siga las instrucciones detalladas en Programación
Del Control De Dispositivo en la página 28 para programar el control de dispositivo para el convertidor de cable y servicio interactivo deseados.
Hecho esto, siga los pasos restantes (5 y 6, en esta página) para bloquear de nuevo el ID.
En el control remoto, presione CBL una vez. Presione y mantenga presionado SETUP hasta que la tecla
CBL parpadee dos veces.A continuación, suelte el botón SETUP.
Presione 9 - 8 - 2. La tecla CBL parpadeará dos veces.
33
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 34
PROGRAMACIÓN DEL BLOQUEO
DEL CONTROL DE CANAL
Las funciones de control de canal del control remoto están por defecto bloqueadas en relación con el convertidor de cable. Las teclas afectadas* son 0 ~ 9, CH+, CH-, ENTER, y LAST. Esto evitará que usted cambie sin querer el canal de su TV o VCR.No obstante, puede desactivar esta función para permitir un acceso total a estas teclas en los modos TV y VCR.
*NOTA: Esta función no afecta al modo AUD.
Desactivación Del Bloqueo Del Control De Canal:
1.
En el control remoto, presione CBL una vez. Presione y mantenga presionado SETUP hasta que la tecla
CBL parpadee dos veces.A continuación, suelte el botón SETUP.
2.
Presione 9 - 7 - 3. La tecla CBL parpadeará dos veces.
3.
4.
Presione CH- una vez. La tecla CBL parpadeará cuatro veces.
Ahora el control remoto proporcionará funciones de control de canal de TV y VCR siempre que esté en el modo TV o VCR.
Reactivación Del Bloqueo Del Control De Canal:
1.
En el control remoto, presione CBL una vez. Presione y mantenga presionado SETUP hasta que la tecla
CBL parpadee dos veces.A continuación, suelte el botón SETUP.
2.
Presione 9 - 7 - 3. La tecla CBL parpadeará dos veces.
3.
4.
Presione CH+ una vez. La tecla CBL parpadeará dos veces.
En este momento, sólo estará disponible la función de control de canal de su convertidor de cable, independientemente del modo que seleccione
(p. ej., TV, VCR, o CBL).
34
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 35
UTILIZACIÓN DEL BOTÓN DE
ENCENDIDO PRINCIPAL
El Control Remoto Universal Atlas está equipado con una función exclusiva que le permite encender o apagarde manera secuencial todos sus dispositivos de entretenimiento doméstico con un único botón.
NOTA: MASTER POWER solo funciona en el modo CBL. En caso de no estar programado, solo se encenderá o apagará el convertidor de cable.
En cualquier otro modo, al pulsar una vez MASTER POWER se encenderá o apagará el dispositivo seleccionado.
Programación Del Botón De Encendido Principal:
1.
2.
Presione y mantenga presionado SETUP hasta que el dispositivo seleccionado en último lugar parpadee dos veces.A continuación, suelte el botón SETUP.
Presione 9 - 9 - 5. La tecla del dispositivo seleccionado en último lugar parpadeará dos veces.A continuación, presione POWER una vez.
3.
Pulse una tecla de dispositivo (p. ej., CBL) una vez y a continuación POWER para el primer dispositivo que desee en la lista de encendido.
4.
5.
Repita el paso 3 hasta tres veces más para añadir el segundo, tercer y cuarto dispositivos según estime oportuno.
Para guardar la configuración y salir del programa, pulse CBL una vez.A continuación, presione y mantenga presionado SETUP hasta que la tecla CBL parpadee dos veces. Suelte el botón SETUP.
Restablecimiento Del Botón De Encendido Principal:
1.
2.
Para restablecer la configuración y salir del programa, presione y mantenga presionado SETUP hasta que la tecla CBL parpadee dos veces.A continuación, libere
SETUP.
Utilización Del Botón De Encendido Principal:
1.
Siga los pasos 1 y 2 como se indica en la sección anterior.
2.
3.
Después de haberlo programado, dirija el control remoto hacia los dispositivos. Presione CBL una vez.
Presione POWER una vez para encender o apagar todos los dispositivos de entretenimiento doméstico de forma secuencial.
Podrá ver los dispositivos encenderse o apagarse de acuerdo a la secuencia programada.
35
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 36
REASIGNACIÓN DE TECLAS DE DISPOSITIVOS
El Control Remoto Universal Atlas puede configurarse para su utilización con un segundo dispositivo de TV o VCR, o cualquier otra combinación de cuatro dispositivos de entretenimiento doméstico.
Por ejemplo, para utilizar el control con una TV, un convertidor de cable, y dos VCR, deberá reasignar la tecla AUD fuera de uso para utilizarla con el segundo VCR, de la siguiente manera:
1.
En el control remoto, presione VCR una vez.
Presione y mantenga presionado SETUP hasta que la tecla VCR parpadee dos veces. A continuación, libere el botón SETUP.
2.
Presione 9 - 9 - 2. La tecla VCR parpadeará dos veces.
3.
4.
Presione VCR una vez. Presione luego AUD. La tecla
AUD parpadeará dos veces.
La tecla AUD podrá ya ser programada para su segundo VCR. Consulte Programación De Control De
Dispositivos en la página 28.
Para reasignar otras teclas de dispositivos, repita los pasos del 1 al 4 sustituyendo la secuencia de teclas tal y como se indica en el siguiente cuadro:
Para Reasignar Secuencia De Teclas
TV como segunda tecla de VCR: TV - SETUP - 9 - 9 - 2 - VCR - TV
TV como segunda tecla de Audio: TV - SETUP - 9 - 9 - 2 - AUD - TV
TV como segunda tecla de Cable: TV - SETUP - 9 - 9 - 2 - CBL - TV
TV volver a TV: TV - SETUP - 9 - 9 - 2 - TV - TV
VCR como segunda tecla de TV: VCR - SETUP - 9 - 9 - 2 - TV - VCR
VCR como segunda tecla de Audio: VCR - SETUP - 9 - 9 - 2 - AUD- VCR
VCR como segunda tecla de Cable: VCR - SETUP - 9 - 9 - 2 - CBL- VCR
VCR volver a VCR: VCR - SETUP- 9 - 9 - 2 - VCR - VCR
AUD como segunda tecla de TV: AUD - SETUP - 9 - 9 - 2 - TV - AUD
AUD como segunda tecla de Cable: AUD - SETUP - 9 - 9 - 2 - CBL - AUD
AUD volver a AUD: AUD - SETUP - 9 - 9 - 2 - AUD -AUD
Una vez completada la reasignación, el modo seleccionado parpadeará dos veces para confirmar su selección.
A continuación, programe el control de dispositivos (consulte
Programación De Control De Dispositivos en la página 28).
36
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 37
UTILIZACIÓN DE MACROS
Durante la programación, la tecla MACRO de su Control Remoto
Universal Atlas puede ser configurada para realizar funciones repetitivas y lentas presionando una sola vez la tecla. Un macro puede ser utilizado para controlar el funcionamiento de un home theater (cine en casa), para configurar un canal o para otras múltiples funciones que usted quiera controlar con sólo una tecla (ver ejemplos más adelante).Además, la tecla MACRO puede almacenar tres macros con hasta 15 funciones de tecla cada uno. Los macros se activan en el orden que fueron almacenados cada vez que usted presione la tecla.
NOTA: Si se programa un macro habiendo ya tres almacenados, se eliminará el macro almacenado en primer lugar. A partir de entonces, cada nuevo macro sobrescribirá sobre el siguiente macro original.
Ejemplo – Programación De Su Canal Favorito
Su servidor de cable ofrece infinidad de canales diferentes. Con
Atlas, puede programar un macro que seleccione directamente su canal favorito con una sola tecla. Por ejemplo, digamos que sus programas de cable favoritos están en el canal 71. Siga las instrucciones siguientes para programar un macro que le permita acceder directamente a este canal:
1.
En el control remoto, presione CBL una vez. Presione y mantenga presionado SETUP hasta que la tecla
CBL parpadee dos veces.A continuación, suelte el botón SETUP.
2.
Presione 9 - 9 - 5. La tecla CBL parpadeará dos veces.
3.
Presione MACRO una vez.
4.
Presione CBL una vez.
5.
6.
Presione el número de canal, 7 - 1.
NOTA: Si tiene acceso a más de 100 canales, presione 0 - 7 -1.
Además, si el control remoto original requería presionar la tecla Enter para cambiar de canal, deberá presionar la tecla
ENTER después del número de canal (p. ej., 0 -7 - 1 - ENTER).
Presione y mantenga presionado SETUP hasta que la tecla CBL parpadee dos veces.A continuación, suelte el botón SETUP.
Ahora, cuando presione MACRO, el convertidor de cable sintonizará de forma instantánea el canal 71.
NOTA: Para almacenar tres canales en l a tecla MACRO, repita los seis pasos anteriores dos veces más, introduciendo un nuevo número de canal en el paso 5 (p. ej., 7 – 2 para el canal 72).
37
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 38
3.
4.
UTILIZACIÓN DE MACROS (continuación)
Eliminación De Macros:
1.
2.
En el control remoto, presione y mantenga presionado
SETUP hasta que el dispositivo seleccionado en
último lugar parpadee dos veces.A continuación, suelte el botón SETUP.
Presione 9 - 9 - 5. La tecla del dispositivo seleccionado en último lugar parpadeará dos veces.
Presione MACRO una vez.
Presione y mantenga presionado SETUP hasta que el
último dispositivo seleccionado parpadee dos veces.
A continuación, suelte el botón SETUP.
NOTA: Los macros se eliminarán en el orden en que fueron almacenados.
3.
4.
CAMBIO DEL BLOQUEO DE VOLUMEN
En el Control Remoto Universal Atlas, el bloqueo De Volumen
Total está configurado en TV, de modo que podrá controlar al volumen de la TV aun estando en los modos TV,VCR, o Cable.
Si lo desea, puede realizar un des bloqueo De Volumen Individual en un dispositivo seleccionado para configurar su control de volumen de manera que lo pueda controlar de forma independiente.
NOTA: Si bloquea los controles de volumen en el modo AUDIO, podrá controlar el volumen del dispositivo de audio en todos los demás modos
(p. ej., TV, VCR, y CBL).
Desbloqueo Del Control De Volumen Para Un Sólo
Dispositivo (Desbloqueo De Volumen Individual):
1.
2.
Teniendo en cuenta que control De Volumen Total debe estar activado, seleccione en el control remoto el modo que desea desbloquear (p.ej., CBL) y presione una vez.Presione y mantenga presionado SETUP hasta que la tecla de dispositivo parpadee dos veces.
A continuación, libere el botón SETUP.
Presione 9 - 9 - 3. La tecla del dispositivo seleccionado en último lugar parpadeará dos veces.
Presione VOL- una vez. El dispositivo seleccionado parpadeará cuatro veces.
Repita los pasos 1 a 3 de esta sección para cada dispositivo cuyo volumen desee desbloquear.
38
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 39
5.
Ahora bien, una vez haya seleccionado desbloquear el volumen de un dispositivo (p. ej., CBL), las teclas
VOL+, VOL-, o MUTE controlarán el volumen del dispositivo sólo en el modo de éste.
Desbloqueo De Todos Los Controles De Volumen
(Desbloqueo De Volumen Total):
NOTA: Estas instrucciones le permitirán configurar un control de volumen independiente para cada uno de los dispositivos programados (p. ej, control de volumen de TV en el modo TV, control de volumen de VCR en el modo VCR, etc.).
1.
En el control remoto, presione y mantenga presionado
SETUP hasta que el dispositivo seleccionado en último lugar parpadee dos veces.A continuación, suelte el botón SETUP.
2.
Presione 9 - 9 - 3. La tecla del dispositivo seleccionado en último lugar parpadeará dos veces.
3.
Presione VOL+ una vez. El último dispositivo seleccionado parpadeará cuatro veces.
Bloqueo De Volumen En Un Modo
(Bloqueo De Volumen Total):
NOTA: Si bloquea los controles de volumen en el modo AUDIO, podrá controlar el volumen del dispositivo de audio en todos los demás modos (p.
ej., TV, VCR y CBL).
1.
En el control remoto, presione y mantenga presionado
SETUP hasta que el dispositivo seleccionado en último lugar parpadee dos veces.A continuación, suelte el botón SETUP.
2.
Presione 9 - 9 - 3. La tecla del dispositivo seleccionado en último lugar parpadeará dos veces.
3.
4.
Seleccione un modo (p. ej., TV) en el que desee bloquear de forma total los controles de volumen.
El modo seleccionado parpadeará dos veces.
Ahora cuando presione VOL+, VOL-, o MUTE, podrá controlar el volumen del dispositivo seleccionado
(p. ej., TV).
39
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 40
RESOLUCIÓN DE PROBLEMAS
PROBLEMA: La tecla de modo no parpadea cuando presiona una tecla.
SOLUCIÓN: Sustituya las baterías gastadas por dos (2) baterías alcalinas nuevas del tipo AA (consulte la página 27).
PROBLEMA: La tecla de modo parpadea cuando presiona una tecla, pero el dispositivo de entretenimiento doméstico no responde.
SOLUCIÓN: Asegúrese de que está dirigiendo el control remoto hacia su dispositivo de entretenimiento doméstico y de que está situado a 5 metros del dispositivo con el que está intentando utilizar el control remoto.
PROBLEMA: El control remoto no funciona con los dispositivos de entretenimiento doméstico o las órdenes no se ejecutan correctamente.
SOLUCIÓN: Pruebe todos los códigos enumerados para la marca del dispositivo que está siendo configurado.Asegúrese de que todos los dispositivos pueden recibir señal de un control remoto.
PROBLEMA: El combo TV/VCR no responde correctamente.
SOLUCIÓN: Utilice los códigos de VCR para su marca.Algunos combos necesitan un código de TV y otro de VCR para funcionar correctamente (consulte la página 48).
PROBLEMA: No hay volumen en la segunda TV.
SOLUCIÓN: Siga las instrucciones indicadas en Cambio De Bloqueo
De Volumen (ver página 38).
PROBLEMA: CH+, CH-, y LAST no funcionan en su TV RCA.
SOLUCIÓN: Debido a los diseños RCA (1983-1987), solo funcion con estas TVs su control remoto original.
PROBLEMA: El cambio de canales no funciona correctamente.
SOLUCIÓN: Si era necesario en el control remoto original presionar
ENTER para cambiar canales, deberá presionar ENTER en su control remoto después de presionar el número de canal.
PROBLEMA: Probó el “Método De Búsqueda” pero aún así no pudo encontrar un código que funcionara.
SOLUCIÓN: Pruebe el “Método De Búsqueda” de nuevo tras borrar la tecla de dispositivo de la manera siguiente: Presione y mantenga presionado SETUP hasta que la tecla de modo parpadee dos veces.A continuación, libere el botón
SETUP. A continuación, introduzca 9 - 9 - 2. Presione y libere dos veces la tecla del moro que desea restablecer.
PROBLEMA: El control remoto no enciende combos TV/VCR de las marcas Sony o Sharp.
SOLUCIÓN: Para encender estos equipos, es necesario programar los códigos de TV en el control remoto. Para Sony, utilice el código de TV 0000 y el código de VCR 0032.
Para Sharp, utilice el código de TV 0093 y el código de
VCR 0048.
40
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 41
INSTRUCCIONES AL USUARIO
Este equipo ha sido probado y se halló que cumple con los límites fijados para los dispositivos digitales de clase B, de acuerdo con la parte
15 de las Reglas de la FCC. Estos límites están diseñados para brindar una protección razonable contra las interferencias dañinas en una instalación residencial. Este equipo genera, usa y puede irradiar energía de radiofrecuencia y, si no se le instala y usa de acuerdo con las instrucciones, podría causar interferencias dañinas a las comunicaciones por radio.
Sin embargo, no hay garantía de que no ocurrirá la interferencia en una instalación en particular. Si este equipo causa interferencias dañinas a la recepción por radio o por televisión, lo cual se puede determinar encendiendo y apagando el equipo, se anima al usuario a que trate de corregir la interferencia con una o más de las siguientes medidas.
• Reoriente o cambie de lugar la antena receptora.
• Aumente la distancia entre el equipo y el receptor.
• Conecte el equipo en una toma de corriente que esté en un circuito diferente al circuito donde está conectado el receptor.
• Consulte al distribuidor o a un técnico experto en radio y televisión para que le asistan.
Se verificó que este equipo cumple con los límites fijados para un dispositivo de computación de clase B, de acuerdo con las Reglas de la
FCC. Para poder mantener el cumplimiento con las reglas de la FCC, se tienen que usar cables blindados con este equipo. La operación con equipos no aprobados o con cables no blindados probablemente resultará en una interferencia en la recepción de radio y televisión. Se cauciona al usuario de que los cambios y modificaciones que se hagan al equipo sin la aprobación del fabricante podrían nulificar la autoridad del usuario para operar este equipo.
INFORMACIÓN ADICIONAL
Este producto no tiene ninguna parte que pueda ser de otra utilidad para el usuario.Abrir la caja, a excepción del compartimiento de las baterías, puede ocasionar daños permanentes en el control remoto.
Para obtener ayuda a través de Internet, visítenos en www.urcsupport.com
Para obtener ayuda a través de correo electrónico, póngase en contacto con nosotros en: [email protected]
Copyright 2003 porUniversal Electronics Inc. Ninguna parte de esta publicación puede ser reproducida, transmitida, transcrita, almacenada en ningún sistema de recuperación, o traducida a cualquier idioma, en ninguna forma o medio, ya sea electrónico, mecánico, magnético, óptico, manual o de otro tipo, sin el consentimiento previo por escrito de
Universal Electronics Inc.
M4030AS 05/03
41
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 42
MANUFACTURER’S CODES
(CÓDIGOS DEL FABRICANTE)
Setup Codes For Audio Amplifiers
(Códigos De Configuración Para
Amplificadores De Audio):
GE 0078
Harman/Kardon 0892
JVC 0331
Luxman
Marantz
Nakamichi
Optimus
0165
0321, 0892
0321
0395
Philips
Polk Audio
Realistic
Sansui
Sony
Soundesign
Victor
Wards
Yamaha
0892
0892
0395
0321
0689
0078
0331
0078
0354
Setup Codes For Audio Receivers
(Códigos De Configuración Para
Receptores De Audio):
ADC
Aiwa
Bose
Capetronic
Carver
Compaq
Denon
0531
0121, 1089, 1405
1229
0531
1089, 1189
1136
1104, 1160
Harman/Kardon 0110
Hewlett Packard 1181
JBL
JVC
0110
0074
Kenwood 0186, 1027, 1313, 1569, 1570
MCS 0039
Magnavox
Marantz
0531, 1089, 1189
0039, 1089, 1189
Onkyo
Optimus
Panasonic
Philips
Pioneer
Proscan
Quasar
RCA
0135
0531, 0670, 0186, 1023
0039, 1518
1089, 1189, 1269
0531, 0014, 0150, 0630, 1023
1254
0039
0531, 1023, 1254
42
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 43
Sansui
Sharp
Sony
Soundesign
Sunfire
Technics
Thorens
Victor
Wards
Yamaha
1089
0186
1058, 1158, 1258
0670
1313
0039, 1308, 1309, 1518
1189
0074
0014
0176, 0186, 1176
Setup Codes For Cable Converters
(Códigos De Configuración Para
Convertidores De Cable):
ABC
Americast
0003, 0008, 0017
0899
Bell South 0899
General Instrument 0476, 0810
GoldStar 0144
Jerrold
Memorex
Motorola
Panasonic
Paragon
Philips
Pioneer
Pulsar
0003, 0476, 0276, 0810
0000
0476
0000
0000
0305, 0317
0144, 0533, 0877, 1877
0000
Quasar
Runco
0000
0000
Samsung 0144
Scientific Atlanta 0008, 0477, 0017, 0877, 1877
Starcom
Supercable
Toshiba
Zenith
0003
0276
0000
0000, 0525, 0899
Setup Codes For DVD Players
(Códigos De Configuración Para
Reproductores DVD):
Aiwa
Apex
Audiologic
B & K
Denon
Emerson
Fisher
0641
0672, 0755
0736
0655, 0662
0490, 0634
0591
0670 continued on next page...
continúa en la página siguiente…
43
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 44
MANUFACTURER’S CODES
(CÓDIGOS DEL FABRICANTE)
Setup Codes For DVD Players, Continued
(Códigos De Configuración Para
Reproductores DVD, Continuación):
Optimus
Oritron
Panasonic
Philips
Pioneer
Princeton
Proscan
RCA
Samsung
Sanyo
Sharp
Sherwood
Sony
Technics
Techwood
Theta Digital
Toshiba
Yamaha
Zenith
GE
GPX
Go Video
0522, 0717
0769
0715
Gradiente 0651
Harman/Kardon 0582
Hitachi
Hiteker
0573, 0664
0672
JVC
Kenwood
Konka
Magnavox
Marantz
Microsoft
Mitsubishi
Onkyo
0558, 0623
0534, 0682
0711, 0719, 0720, 0721
0503, 0675
0539
0522
0521
0503, 0627
0573
0670
0630
0633
0533
0490
0692
0571
0571
0651
0490, 0632, 0677, 0678
0503, 0539
0525, 0571, 0632
0674
0522
0522, 0571, 0704, 0717
0503
0490, 0545
0503, 0591
Setup Codes For TVs
(Códigos De Configuración Para Televisores):
AOC
Admiral
Aiko
Aiwa
Akai
Alaron
0030, 0019
0093, 0463
0092
0701
0030
0179
44
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 45
America Action
Ampro
Anam
Audiovox
Baysonic
Belcor
Bell & Howell
Bradford
Brockwood
Broksonic
CXC
Candle
Carnivale
Carver
Celebrity
0180
0751
0180
0451, 0180, 0092, 0623
0180
0019
0154, 0016
0180
0019
0236, 0463
0180
0030, 0056
0030
0054
0000
Cineral
Citizen
Concerto
Contec
Craig
Crosley
Crown
Curtis Mathes
0451, 0092
0060, 0030, 0056, 0039, 0092
0056
0180
0180
0054
0180, 0039
0047, 0054, 0154, 0051, 0451, 0093, 0060, 0030, 0145, 0056,
0016, 0039, 0166, 0466, 1147, 1347
0451, 0019, 0039, 0092, 0623, 0624
0019
0145
Daewoo
Daytron
Denon
Dumont
Dwin
Electroband
Emerson
Envision
Fisher
Fujitsu
Funai
Futuretech
GE
Gibralter
GoldStar
Gradiente
Grunpy
Hallmark
0017, 0019
0720, 0774
0000
0154, 0236, 0463, 0180, 0282, 0178, 0019, 0179, 0039, 0623,
0624
0030
0154
0179, 0683
0180, 0179, 0171
0180
0047, 0051, 0451, 0093, 0282, 0178, 0021, 0135, 1147, 1347
0017, 0030, 0019
0030, 0178, 0019, 0056
0053, 0056
0180, 0179
0178
Harley Davidson 0179
Harman/Kardon 0054
Harvard
Hitachi
0180
0145, 0056, 0016
Infinity
Inteq
JBL
0054
0017
0054 continued on next page...
continúa en la página siguiente…
45
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 46
MANUFACTURER’S CODES
(CÓDIGOS DEL FABRICANTE)
Philco
Philips
Pilot
Pioneer
Portland
Princeton
Prism
Proscan
Proton
Pulsar
Quasar
Setup Codes For TVs, Continued
(Códigos De Configuración Para Televisores,
Continuación):
Matsushita
Megatron
Memorex
Midland
Minutz
Mitsubishi
Motorola
Multitech
NAD
NEC
NTC
Nikko
Onwa
Optimus
Optonica
Orion
Panasonic
Penney
JCB
JVC
KEC
KTV
Kenwood
Konka
LG
LXI
Logik
Luxman
MGA
MTC
Magnavox
Majestic
Marantz
0000
0053
0180
0180, 0030, 0039
0030, 0019
0628, 0632, 0638, 0703, 0707
0056
0047, 0054, 0154, 0156, 0178
0016
0056
0150, 0030, 0178, 0019
0060, 0030, 0019, 0056
0054, 0030, 0179
0016
0054, 0030
0250
0178, 0145
0154, 0250, 0463, 0150, 0178, 0179, 0056, 0016
0047, 0017, 0051, 0039, 0135
0021
0093, 0150, 0178, 0019
0093
0180
0156, 0178, 0166
0030, 0019, 0056
0092
0030, 0178, 0092
0180
0154, 0250, 0166
0093, 0165
0236, 0463, 0179
0051, 0250
0047, 0156, 0051, 0060, 0030, 0178, 0021, 0019, 0056, 0039,
0135, 1347
0054, 0463, 0030, 0145, 0019
0054
0030, 0019, 0039
0166, 0679
0019, 0039, 0092
0717
0051
0047
0178, 0466
0017, 0019
0051, 0250, 0165
46
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 47
Semivox
Semp
Sharp
Shogun
Signature
Sony
Soundesign
Squareview
Starlite
Supreme
Sylvania
Symphonic
TMK
TNCi
Tandy
Technics
RCA
RadioShack
Realistic
Runco
SSS
Sampo
Samsung
Samsux
Sansei
Sansui
Sanyo
Scimitsu
Scotch
Scott
Sears
0047, 0051, 0093, 0019, 0090, 0135, 0679, 1047, 1147, 1347
0047, 0154, 0165, 0180, 0030, 0178, 0019, 0056, 0039
0154, 0165, 0180, 0030, 0178, 0019, 0056, 0039
0017, 0030, 0603
0180, 0019
0030, 0039
0060, 0030, 0178, 0019, 0056
0039
0451
0463
0154
0019
0178
0236, 0180, 0178, 0019, 0179
0047, 0054, 0154, 0156, 0178, 0179, 0056, 0171
0180
0156
0093, 0165, 0039, 0688
0019
0016
0000
0180, 0178, 0179
0171
0180
0000
0054, 0030
0180, 0171
0178, 0056
0017
0093
0051, 0250
Technol Ace
Techwood
Teknika
Telefunken
Toshiba
Totevision
Vector Research
Victor
0179
0051, 0056
0054, 0180, 0150, 0060, 0019, 0179, 0056, 0016, 0039, 0092
0056
0154, 0156, 0060, 1256
0039
0030
0053
Vidikron
Vidtech
0054
0178, 0019
Wards 0054, 0165, 0030, 0178, 0021, 0019, 0179, 0056, 0016
White Westinghouse 0463, 0623, 0624
Yamaha
Zenith
0030, 0019
0017, 0463, 0016, 0092, 0624 continued on next page...
continúa en la página siguiente…
47
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 48
MANUFACTURER’S CODES, continued
(CÓDIGOS DEL FABRICANTE, continuación)
Setup Codes For TV/VCR Combos
(Códigos De Configuración Para Aparatos
Combinados Televisor/Videograbadora):
Broksonic
Citizen
Colt
Curtis Mathes
Daewoo
0002, 0479 (for TV use 0463)
0278
0072
0035 (for TV use 0051)
0278 (for TV use 0624)
Emerson
Funai
GE
0002, 0278 (for TV use 0624), 0479 (for TV use 0463)
0000
0035 (for TV use 0051), 0048 (for TV use 0093),
0060 (for TV use 0047), 0240
GoldStar 0037 (for TV use 0056)
Harley Davidson 0000
Hitachi
Lloyd’s
Magnasonic
Magnavox
0000
0000
0278
0000, 0081 (for TV use 0054)
Magnin
Memorex
MGA
Mitsubishi
0240
0037, 0162 (for TV use 0250), 1162
0240
0048 (for TV use 0093)
Optimus
Orion
Panasonic
Penney
0162 (for TV use 0250), 1162, 1262
0002, 0479 (for TV use 0463)
0035 (for TV use 0051), 0162 (for TV use 0250), 1162
0035 (for TV use 0051), 0037 (for TV use 0056), 0240
0035 (for TV use 0051), 0162 (for TV use 0250) Quasar
RCA
Sansui
Sanyo
Sears
Sharp
Sony
Sylvania
Symphonic
0035 (for TV use 0051), 0048 (for TV use 0093),
0060 (for TV use 0047), 0240
0000, 0479 (for TV use 0463)
0240
0000, 0037 (for TV use 0056)
0048 (for TV use 0093)
0000, 0032 (for TV use 0000)
0081 (for TV use 0054)
0000, 0563
Thomas 0000
White Westinghouse 0278 (for TV use 0624)
Zenith 0000
Setup Codes For VCRs And PVRs
(Códigos De Configuración Para
Videograbadoras Y PVRs):
Admiral
Adventura
Aiko
0048, 0209
0000
0278
48
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 49
Aiwa
Akai
America Action
American High
Asha
Audiovox
Beaumark
Bell & Howell
Broksonic
CCE
Calix
Canon
Carver
Cineral
Citizen
Colt
0037, 0000
0041
0278
0035
0240
0037
0240
0104
0184, 0121, 0209, 0002, 0479
0072, 0278
0037
0035
0081
0278
0037, 0278
0072
Craig
Curtis Mathes
Cybernex
Daewoo
Denon
Dynatech
Electrohome
Electrophonic
Emerex
Emerson
Fisher
Fuji
Funai
GE
Garrard
Go Video
GoldStar
Gradiente
HI-Q
0432
0037, 0038
0000
0047
Harley Davidson 0000
Harman/Kardon 0081, 0038
Harwood
Hitachi
0072
0000, 0042, 0041
Hughes Net. Sys.
0042
JVC 0067, 0041
Jensen
KEC
0041
0037, 0278
KLH
Kenwood
Kodak
LXI
0072
0067, 0041, 0038
0035, 0037
0037
Lloyd’s
Logik
MEI
0000
0072
0035
0037, 0047, 0240, 0072
0060, 0035, 0041, 0162, 0760
0240
0045, 0278
0042
0000
0037
0037
0032
0037, 0184, 0000, 0121, 0043, 0209, 0002, 0278, 0479
0047, 0104
0035, 0033
0000
0060, 0035, 0048, 0240, 0760
0000 continued on next page...
continúa en la página siguiente…
49
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 50
MANUFACTURER’S CODES
(CÓDIGOS DEL FABRICANTE)
Setup Codes For VCRs And PVRs, Continued
(Códigos De Configuración Para
Videograbadoras Y PVRs, Continuación):
RadioShack
Radix
Randex
Realistic
ReplayTV
Runco
STS
Samsung
Sanky
Sansui
MGA 0240, 0043
MGN Technology 0240
MTC 0240, 0000
Magnasonic
Magnavox
Magnin
Marantz
0278
0035, 0039, 0081, 0000, 0149
0240
0035, 0081
Marta
Matsushita
Memorex
Minolta
Mitsubishi
Motorola
Multitech
NEC
Nikko
Noblex
Olympus
Optimus
Orion
Panasonic
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Polk Audio
Profitronic
Proscan
Protec
Pulsar
Quasar
RCA
0037
0035, 0162
0035, 0037, 0048, 0039, 0047, 0240, 0000, 0104, 0209, 0162,
0479, 1162
0042
0048, 0067, 0043
0035, 0048
0000, 0072
0104, 0067, 0041, 0038
0037
0240
0035
0037, 0048, 0104, 0162, 0432, 1162
0184, 0209, 0002, 0479
0035, 0162, 0225, 0616, 1162
0035, 0037, 0240, 0042, 0038
0042
0035, 0209, 0479
0035, 0081, 0618, 1081, 1181
0037
0067
0081
0240
0060, 0760
0072
0039
0035, 0162, 1162
0060, 0035, 0048, 0240, 0042, 0149, 0760
0000
0037
0037
0035, 0037, 0048, 0047, 0000, 0104
0614, 0616
0039
0042
0240, 0045
0048, 0039
0000, 0067, 0209, 0041, 0479
50
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 51
Sanyo
Scott
Sears
Semp
Sharp
Shintom
Shogun
Singer
Sony
Sylvania
Symphonic
TMK
Tatung
Teac
Technics
Teknika
Thomas
Tivo
Toshiba
Totevision
0047, 0240, 0104
0184, 0045, 0121, 0043
0035, 0037, 0047, 0000, 0042, 0104
0045
0048
0072
0240
0072
0035, 0032, 0000, 0033, 0636
0035, 0081, 0000, 0043
0000
0240
0041
0000, 0041
0035, 0162
0035, 0037, 0000
0000
0618, 0636
0045, 0043
0037, 0240
Unitech
Vector
Vector Research
Video Concepts
Videosonic
Wards
0240
0045
0038
0045
0240
0060, 0035, 0048, 0047, 0081, 0240, 0000, 0042, 0072, 0149,
0760
White Westinghouse 0209, 0072, 0278
XR-1000 0035, 0000, 0072
Yamaha
Zenith
0038
0039, 0000, 0209, 0033, 0479
51
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 52
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 Key Charts
- 14 To De-Activate Channel Control Lock
- 14 To Re-Activate Channel Control Lock
- 15 To Program The Master Power Key
- 15 To Clear The Master Power Key
- 15 To Operate The Master Power Key
- 17 Example – Programming A Favorite Channel
- 18 To Clear A Macro
- 18 (Individual Volume Unlock)
- 19 (Global Volume Unlock)
- 19 (Global Volume Lock)
- 42 Setup Codes for Audio Amplifiers
- 42 Setup Codes for Audio Receivers
- 43 Setup Codes for Cable Converters
- 43 Setup Codes for DVD Players
- 44 Setup Codes for TVs
- 48 Setup Codes for TV/VCR Combos
- 48 Setup Codes for VCRs and PVRs