Emerson 1F85-0422 Operating instructions

Blue Universal Thermostat with
Automatic Heat/Cool Changeover Option
Single Stage, Multi-Stage or Heat Pump
Installation and Operating Instructions for Models:
Save these instructions for future use!
Model
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS
CAREFULLY BEFORE INSTALLING OR OPERATING
THIS CONTROL COULD CAUSE PERSONAL INJURY
AND/OR PROPERTY DAMAGE.
1F85-0422
1F83-0422
Programming Choices
5/1/1 Day
5/2 Day
Non-Programmable
Non-Programmable
APPLICATIONS
THERMOSTAT APPLICATION GUIDE
Description
Heat Pump (No Aux. or Emergency Heat)
Heat Pump (with Aux. or Emergency Heat)
Systems with up to 2 Stages Heat, 2 Stages Cool
Heat Only Systems (with optional fan switch)
Millivolt Heat Only Systems – Floor or Wall Furnaces
Cool Only Systems
Gas or Oil Heat
1F83-0422 Thermostat
Electric Furnace
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Hydronic (Hot Water) Zone Heat – 2 Wires
Hydronic (Hot Water) Zone Heat – 3 Wires
Yes
Yes
SPECIFICATIONS
Electrical Rating:
Battery Power..................................................... mV to 30 VAC, NEC Class II, 50/60 Hz or DC
Input-Hardwire.................................................... 20 to 30 VAC
Terminal Load............................................................ 1.5 A per terminal, 2.5A maximum all terminals combined
Setpoint Range.......................................................... 45° to 90°F (7° to 32°C)
Differential (Single Stage).......................................... Heat 0.6°F; Cool 1.2°F (adjustable)
Differential (Heat Pump)............................................ Heat 1.2°F; Cool 1.2°F (adjustable)
Operating Ambient..................................................... 32° to +105°F (0° to +41°C)
Operating Humidity.................................................... 90% non-condensing max.
Shipping Temperature Range.................................... -4° to +150°F (-20° to +65°C)
Dimensions Thermostat............................................. 3-7/8”H x 5-1/8”W x 1-1/4”D
! CAUTION
To prevent electrical shock and/or equipment damage,
disconnect electric power to system at main fuse or
circuit breaker box until installation is complete.
Index
Page
Installation
2
Wiring Connections
Thermostat Quick Reference
Installer Configuration Menu
Operating Your Thermostat
Programming
Troubleshooting
2
3
4
6
7
8
ATTENTION: MERCURY NOTICE
This product does not contain mercury. However, this
product may replace a product that contains mercury.
Mercury and products containing mercury must not be
discarded in household trash. Do not touch any spilled
mercury. Wearing non-absorbent gloves, clean up any
spilled mercury and place in a sealed container. For
proper disposal of a product containing mercury or a
sealed container of spilled mercury, place it in a suitable
shipping container. Refer to www.white-rodgers.com for
location to send product containing mercury.
PART NO. 37-7136A
www.white-rodgers.com
www.emersonclimate.com
1
1007
INSTALLATION
!
Figure 1 – Battery door shown open
WARNING
Thermostat installation and all components of the
control system shall conform to Class II circuits per
the NEC code.
“AA” Alkaline Batteries
Remove Old Thermostat
A standard heat/cool thermostat consists of three basic parts:
1) The cover, which may be either a snap-on or hinge type.
2) The base, which is removed by loosening all captive screws.
3) The switching subbase, which is removed by unscrewing
the mounting screws that hold it on the wall or adapter
plate. Before removing wires from old thermostat,
label each wire with the terminal designation from
which it was attached. Disconnect the wires from the
old thermostat one at a time. Do not let wires fall back
into the wall.
Thermostat can be powered by system AC power or Battery.
If
is displayed, the thermostat is battery powered. If
is not displayed, thermostat is system powered with optional
battery back-up. When battery power remaining is approximately half, the
will be displayed. When “Change
”
is displayed, install fresh “AA” alkaline batteries immediately.
For best results, replace all batteries with new premium brand
alkaline batteries such as Duracell® or Energizer®. We recommend replacing batteries every 2 years. If the home is going
to be unoccupied for an extended period (over 3 months) and
is displayed, the batteries should be replaced before
leaving. When less than two months of battery life remain, the
setpoint temperature will offset by 10 degrees (10 degrees
cooler in Heat mode / 10 degrees warmer in Cool mode). If
offset occurs, the normal setpoint can be manually reset with
or
. Another offset will occur within two days if batteries are not replaced.
Installing New Thermostat
1)
2)
3)
4)
5)
6)
7)
Pull the thermostat body off the thermostat base. Forcing
or prying on the thermostat will cause damage to the unit.
Place base over hole in wall and mark mounting hole
locations on wall using base as a template.
Move base out of the way. Drill mounting holes. If you
are using existing mounting holes and the holes drilled
are too large and do not allow you to tighten base snugly,
use plastic screw anchors to secure the base.
Fasten base snugly to wall using mounting holes shown
in Figure 2 and two mounting screws. Leveling is for
appearance only and will not affect thermostat operation.
Connect wires to terminal block on base.
Push excess wire into wall and plug hole with a fire resistant material (such as fiberglass insulation) to prevent
drafts from affecting thermostat operation.
Carefully line the thermostat up with the base and snap
into place.
Figure 2 – Thermostat base and rear view of thermostat
Mounting
Hole
Place Level
across
Mounting Tabs
(for appearance only)
Mounting
Hole
Place Level
across
Mounting Tabs
(for appearance only)
Batteries
2 “AA” alkaline batteries are included with the thermostat.
To install the batteries, pull the battery door as shown by the
arrow and lift open. Using the polarity indicated inside the battery door, insert the batteries. To close the battery door, swing
the door down while pulling in the direction of arrow. Once
fully down, snap the door back into position. To replace the
batteries, set system to OFF.
WIRING CONNECTIONS
Refer to 37-6895 for 1F83-0422/1F85-0422 wiring diagram
specifications.
Refer to equipment manufacturers’ instructions for specific
system wiring information. After wiring, see CONFIGURATION
section for proper thermostat configuration.
TERMINAL DESIGNATION DESCRIPTIONS
Terminal
Designation
Description
L...............Heat pump malfunction indicator for systems
with malfunction connection
O...............Changeover valve for heat pump energized
constantly in cooling
B...............Changeover valve for heat pump energized
constantly in heating
Y...............Compressor Relay
Y2..............2nd Stage Compressor
2
Terminal
Designation
Description
W/E.............Heat Relay/Emergency Heat Relay (Stage 1)
W2..............2nd Stage Heat (3rd Stage Heat in HP 2)
G...............Fan Relay
RH..............Power for Heating
RC..............Power for Cooling
C...............Common wire from secondary side of cooling system transformer or heat only system transformer
6...............3 Wire Zone Valve – Energized when no call for Heat
THERMOSTAT QUICK REFERENCE
Home Screen Description
Figure 3 – Home Screen Display
Setting
Temperature
Room
Temperature
Displays the power level of
the 2 “AA” batteries:
indicates good power level
indicates batteries at about
half power. “Change
” indicates
batteries are low and should be
replaced with 2 new premium brand
“AA” Alkaline batteries.
(See page 2 for more details)
Set
FAN
Auto
SYSTEM
Heat
System
Indicator
Menu
Fan
Indicator
Figure 4 – Programming & Configuration Items
2
12
3
1
9
4
Mo Tu We Th Fr Sa Su
P Date Set
Temp Hold
Save
Month Call For Service
Year
Change
Hold
Filter
System On 2
Auto Sched
Cool Savings
Heat Pump
SYSTEM
Heat Emer Auto
Cool Off Time
FAN
On Auto
Run Sched
5
6
Programming and Configuration Items
1 “System On” indicates when heating or cooling stage
is energized. “System On +2” indicates when a second
stage is energized.
2 The word HOLD is displayed when the thermostat is in
the HOLD mode. Temp HOLD is displayed when
the thermostat is in a Temporary HOLD mode.
3 Displays Change Filter when the system has run for
the programmed filter time period as a reminder to
change or clean your filter.
4 Displays “Set” for setpoint when in Run Program mode.
5 Displays System Mode (Heat, Emer, Auto, Cool, Off)
or Time in menu mode.
6 Displays Fan Mode (On, Auto) or “Run Sched” in Menu mode.
8
10
11
Run
Schedule
Menu
7
7 Displays “Run Schedule”, “Schedule”, or “Menu”.
TM
8 Displays “Save” when Cool Savings is working.
Displays “Heat Pump” when system is configured
9
as Heat Pump thermostat.
10 Displays “Hold” in programmable mode when not in
“Hold” mode. Displays Light Bulb in non-programmable
mode.
11 Initially displays “Auto Sched”. If Auto Schedule had
been used or disabled, then it displays “Cool Savings”
when in the Cool Mode if Cool Savings has been enabled in the menu.
12 “Call For Service” indicates a fault in the heating/
cooling system, it does not indicate a fault in the
thermostat.
3
INSTALLER/CONFIGURATION MENU
With thermostat in Heat, Cool or Auto, in normal operation, press the Menu button for at least 5 seconds. The display will show
item #1 in the table below. Press Menu to advance to the next menu, Press
or
to change an item option. Shaded
items are not available to 1F86.
INSTALLER/CONFIGURATION MENU
MENU
DISPLAYED
PRESS
or
to
Press
REF. HP SS BUTTON (FACTORY DEFAULT) select from listed options
4
1
1
1
MENU
Lk (OFF)
L
2
2
2
MENU
MENU
0
(MS 2)
001 to 999
HP 1, SS 1
3
3
3
MENU
ELE
4
4
4
MENU
1, 2, 4, 5, 6
5
5
5
MENU
(GAS) for SS or MS
(ELE) for HP
CS (0)
(Disabled)
E (On)
6
–
6
MENU
CR Heat (ME)
SL, FA
7
6
–
MENU
SL, FA
8
7
7
MENU
CR Heat Pump
(ME)
CR Cool (ME)
or
CR Emer (FA)
9
10
8
9
8
9
MENU
MENU
11
12
10 10
11 11
MENU
MENU
13
12 12
MENU
14
13 13
MENU
15
16
14 14
15 15
MENU
MENU
17
16 16
MENU
18
17 17
MENU
19
18
–
MENU
20
19
–
MENU
21
20
MENU
22
21 18
MENU
23
22 19
MENU
MENU
24
23 20
MENU
24 21
RUN
SCHED
CL (OFF)
Heat Auto
OFF
SL, FA
SL
COMMENTS
Selects Keypad Lockout.
(Not available on earlier models)
Selects Keypad lockout combination number
Selects Multi-Stage (MS 2 No Heat Pump),
Heat Pump 1 (HP 1, 1 compressor),
or Single Stage (SS 1)
GAS setting: furnace controls the blower
ELE setting: thermostat controls the blower
Selects Cool Savings
Value 1 (low) to 6 (high), Value 0 Disables Feature
Selects Energy Management Recovery (EMR)
On or OFF. 1F85 only
Adjustable Anticipation:
Selects heating cycle rate for MS or SS
Adjustable Anticipation (Heat Pump) (only
when heat pump selected in #1)
Adjustable Anticipation: Selects the cycle rate for
cooling (only when MS 2 or SS 1 is selected in
item 1.) or Selects the cycle rate for Emergency
mode and Auxiliary stage if Heat Pump is
selected in item 1.
Compressor Lockout Time
System Mode Configuration
with Automatic Changeover capability
CL On
Heat Cool Off,
Heat Off with Fan icon,
Cool Off
Heat Off without Fan icon
Cool Off, Auto Off
dL (On)
dL OFF
Selects Display Light On or OFF
0
1 HI, 2 HI, 3 HI, 4 HI,
Adjustable Ambient Temperature Display
(current temperature) 1 LO, 2 LO, 3 LO, 4 LO
Selects Fahrenheit/Celsius Temperature Display
°F
°C
L Heat
L 62 to L 89
Selects Limited HEAT Range
(90)
L Cool (45)
L 46 to L 82
Selects Limited COOL Range
P3
P0, P2
Defaults for 5-1-1 programming (P3) but nonprogrammable (PO) or 5-2 programming (P2)
is available on most models. 1F85 only
Heat AS (On)
OFF
Automatic Schedule for heat mode. 1F85 only.
NA to Cool only system.
Cool AS (On)
OFF
Automatic Schedule for cool mode. 1F85 only.
NA to Heat only system.
Heat FA (On)
OFF
Fast Heat option may be disabled by
selecting OFF. NA to SS config.
NA to Cool only system.
Cool FA (On)
OFF
Fast Cool option may be disabled by
selecting OFF. NA to SS config.
NA to Heat only system.
CA (OFF)
Selects active Comfort Alert On or OFF.
On
Require CA II Module. (Not available on earlier
models)
dS (On)
OFF
Selects Automatic daylight Savings Time option
On or OFF. 1F85 only
Change Filter (OFF)
On
Selects Filter Change-out Indicator On or OFF.
Change Filter (200 h)
25-1975 h
Change Filter time in 25 hour increments. This
menu only appears if On is selected in above.
Cool On (o)
Heat On (b)
Selects operation of the reversing valve terminal
(O/B) output as an O or B terminal.
Returns to Normal Operation
INSTALLER/CONFIGURATION MENU
1) Keypad Lockout – This menu selection will display “Lk”
and
and “OFF” (default, keypad not locked out). The
are used to toggle the selection between OFF and
“L” (keypad locked out). When the keypad lockout selection is enabled “L”, and the MENU button is pressed
again, the display will indicate the number “0” (default,
and
are
still disabled) in the time digits. The
used to set the combination number from 0 to 999. If a
combination of 0 is selected and the MENU button is
pressed, the menu will be exited and keypad will not be
locked. If 1 to 999 is selected and the MENU button is
pressed, the combination is stored into memory and the
menu is exited. The “LOC” will display designating keypad locked with a valid combination. The SYSTEM button
will operate for 10 seconds after the menu mode is exited
to allow the user to change the mode from “OFF” to the
desired SYSTEM mode.
While the keypad is locked out, a press of MENU will enter the configuration menu. The first menu item displayed
or
keys are
is the combination code “0”. The
used to set the combination unlock number from 0 to
999. If the unlock number matches exactly with the combination lock number stored in memory when the MENU
button is pressed, the keypad is unlocked and the “LOC”
is removed. If the unlock number does not match when
the MENU button is pressed, the combination returns to
“0” for another attempt to set the unlock code. To exit the
menu without unlocking the keypad, press RUN SCHED.
To reset the combination code and unlock the keypad if
the code is forgotten, see troubleshooting section.
2) This control can be configured for:
MS 2 – Multi-Stage System (no heat pump)
HP 1 – Heat Pump with one stage of compressor
SS 1 – Single Stage System
3) GAS or Electric (ELE) fan operation. If the heating system requires the thermostat to energize the fan, select
ELE. Select GAS if the heating system energizes the fan
on a call for heat.
4) Select Cool Savings™ value – Selects the amount
of adjustment for the Cool Savings™ feature in Cool
mode with 1 (1°) being the least amount of adjustment
and 6 (6°) being the most amount of adjustment. Default
value is 0 which disables this feature. Cool Savings is
an optional energy saving feature that can reduce your
cooling costs. It is based on the principal that lower
indoor humidity makes a slightly higher temperature
feel more comfortable. Cool Savings operates during
periods of high demand which normally occur on the
hottest summer days when a cooling system may run
for hours to reach the thermostat setting. Long cooling
run times also lower the indoor humidity. Cool Savings,
very slowly, adjusts the setpoint temperature to make the
setpoint closer to the displayed room temperature, to a
maximum of the number of degrees you select. Adjusting the setpoint temperature over a long cooling run time
allows the system to reach your set temperature and turn
off. The room temperature will actually be higher than
the thermostat displays but the reduction in humidity will
allow comfort at the slightly higher temperature.
To turn this feature on in the Cool mode press Cool Savings. The display will show “Save” next to the
setpoint temperature. When Cool Savings is making adjustments to the room temperature display “Save” will be
flashing and the displayed room temperature may vary
within the adjustment range you selected.
If “Save” is not displayed and this feature is OFF, no
change will occur when the cooling system is continuously running during periods of high demand.
5) Energy Management Recovery: (this step is skipped if
configured to be non-programmable). Energy Manage-
ment Recovery (E) On enables the thermostat to start
heating or cooling early to make the building temperature
reach the program setpoint at the time you specify. Heating will start 5 minutes early for every 1° of temperature
required to reach setpoint.
Example: E On is selected and your heating is pro-
grammed to 65° at night and 70° at 7 AM. If the building temperature is 65°, the difference between 65° and
70° is 5°. Allowing 5 minutes per degree, the thermostat
setpoint will change to 70° at 6:35 AM. Cooling allows
more time per degree, because it takes longer to reach
set temperature.
6, 7 & 8) Cycle Rate Selection – The factory default setting
for Heat and Cool modes, SS1 and MS2 is medium cycle
(ME). For Heat Pump and HP1, the default setting is
medium (ME). For Emer (Aux) the default setting is fast
or
cycle (FA). To change cycle rate, press the
key.
Cycle rate differentials for different settings are:
Fast
Medium Slow
MODE FA
ME
SL
Heat (SS1, MS2)
0.4°F 0.6°F 1.7°F
Cool (SS1, MS2)
0.9°F 1.2°F 1.7°F
Heat Pump (HP1)
0.9°F 1.2°F 1.7°F
Emer (HP1)
0.6°F
-
1.7°F
9) Select Compressor Lockout CL OFF or ON – Selecting CL ON will cause the thermostat to wait 5 minutes
between cooling cycles. This is intended to help protect
the compressor from short cycling. Some newer compressors already have a time delay built in and do not
require this feature. Your compressor manufacturer can
tell you if the lockout feature is already present in their
system. When the thermostat compressor time delay occurs, it will flash the setpoint for up to five minutes.
10) System Mode Configuration – This thermostat is configured for Heat and Cool (SYSTEM switch with Cool Off Heat) default. It can also be configured for Heat and Cool with Auto changeover (Heat, Auto, Cool, Off), Heat only
with fan (Off Heat), Heat only without fan, Auto only (Auto Off), and Cool only (Cool Off).
11) Select Backlight Display – The display backlight improves display contrast in low lighting conditions. When
the “C” terminal is powered, selecting backlight CdL ON
will keep the light on continuously. Select backlight OFF
will turn the light on momentarily after any key is pressed.
When the “C” terminal is not powered, the light will be on
momentarily after any key is pressed no matter whether
the backlight is selected ON or OFF.
12) Select Temperature Display Adjustment 4 LO to 4 HI
– Allows you to adjust the room temperature display up
to 4° higher or lower. Your thermostat was accurately calibrated at the factory, but you have the option to change
the display temperature to match your previous thermostat. The current or adjusted room temperature will be
displayed.
13) Select F° or C° Readout – Changes the display readout
to Celsius or Fahrenheit as required.
14) Limited Heat Range – This feature provides a maximum
setpoint temperature for heat. The default setting is 90°F.
It can be changed between 62°F and 89°F by pressing
or
key.
the
15) Limited Cool Range – This feature provide a minimum
setpoint temperature for cool. The default setting is 45°F.
It can be changed between 46°F and 82°F by pressing
or
key.
the
16) Program Options: 1F85 only, configured for 5/1/1 day or
5/2 day programming or non-programming mode. The
default setting is P3, indicating 5/1/1 day programming.
The programs per week can be changed to P2 or P0 by
5
INSTALLER/CONFIGURATION MENU
pressing the
or
keys. A selection of 0 Days for
non-programmable will eliminate the need for EMR, and
that step in the menu will be skipped.
17 & 18)Select Automatic Schedule – 1F85 only, with just one touch of the Auto Schedule key this feature allows
you to program a desired comfort temperature into all the
program periods along with a 6° set back for night periods of both Heat and Cool programs. Factory default is
“On” for both. When Heat AS On and Cool AS On are
activated while in Heat or Cool mode, select desired
setpoint temperature and press Auto Schedule. This
value will be copied into all the morning, day and evening
program periods. The night program periods will have a
6°F set back.
19 & 20)Select Fast Second Stage ON or OFF – Heat
pump or Multi-stage only, in the run mode, with the fast
Heat feature enabled (FA Heat On), if the Heat setpoint
temperature is manually raised by 3°F (2°C) or more
the second
above the actual temperature using
stage will energize immediately. With FA OFF, second
stage will not energize until the setpoint temperature is
1°F or more above actual temperature for more than ten
minutes. The Fast Cool feature (FA Cool) provides the
same controls when the setpoint temperature is lowered.
21) Comfort Alert with Active Protection – Turn this
feature ON to enable active protection. This allows the
thermostat to identify fault codes sent by the Comfort
Alert module when compressor damage is possible and
react to those codes by turning the compressor off. Fault
codes from the Comfort Alert module will flash on the
thermostat. (Refer to Comfort Alert Yellow Alert Codes
OPERATING YOUR THERMOSTAT
Choose the Fan Setting (Auto or On)
Set the FAN Switch to Auto or On.
Fan Auto is the most commonly selected setting and runs the
fan only when the heating or cooling system is on.
Fan On runs the fan continuously for increased air circulation
or to allow additional air cleaning.
Choose the System Setting
(Heat, Off, Cool, Auto, Emer)
Press the SYSTEM button to select:
Heat: Thermostat controls only the heating system.
Off: Heating and Cooling systems are off.
Cool: Thermostat controls only the cooling system.
Auto: Auto Changeover is used in areas where both heating
and cooling may be required on the same day. AUTO allows
the thermostat to automatically select heating or cooling
depending on the indoor temperature and the selected heat
and cool temperatures. When using AUTO, be sure to set the
Cooling temperatures more than 1° Fahrenheit higher than
the heating temperature.
Emer: (Heat Pump models) Thermostat controls only backup
heating system.
6
in Troubleshooting section.) If a Comfort Alert module is
not connected, or to disable active protection, turn this
feature OFF. If a Comfort Alert module is connected and
this feature is turned OFF, the thermostat will still receive
and flash the fault codes from the Comfort Alert module,
but the active protection will not be enabled to protect the
compressor.
22) Select Daylight Saving Time Calculation – 1F85 only,
this feature will allow the thermostat to calculate the DST
automatically and apply it to the Real Time Clock display.
or
touch keys to select the
Default On. Use
feature OFF.
23) Select Filter Replacement Reminder and Set Run
Time – Select the “Change Filter” reminder On or
OFF. If selected On, press MENU to select the time
period from 25 to 1975 hours in 25 hours increments.
In a typical system, 200 hours (default) of run time is
approximately 30 days. After the selected time of blower
operation, the thermostat will display “Change Filter”
as a reminder to change or clean your air filter. When
“Change Filter” is displayed, press MENU or RUN
SCHED button to clear the display and restart the time to
the next filter change.
24) Select Reversing Valve Output – The O/B option is
factory set at “O” position. This will accommodate the
majority of heat pump applications, which require the
changeover relay to be energized in COOL. If the
thermostat you are replacing or the heat pump being
installed with this thermostat requires a “B” terminal, to
energize the changeover relay in HEAT, the O/B option
should be set at “B” position.
IMPORTANT!
Manual Operation for Non-Programmable
Mode
Press the SYSTEM button to select Heat or Cool and use
the
or
buttons to adjust the temperature to your
desired setting. After selecting your desired settings you can
also press the SYSTEM button to select AUTO to allow the
thermostat to automatically change between Heat and Cool.
Manual Operation (Bypassing the Program)
Programmable Thermostats
Press
or
and then the HOLD button and adjust the
temperature wherever you like. This will override the program.
The HOLD feature bypasses the program and allows you
to adjust the temperature manually, as needed. Whatever
temperature you set in HOLD will be maintained 24 hours
a day, until you manually change the temperature or press
RUN SCHED to cancel HOLD and resume the programmed
schedule.
Program Override (Temporary Override)
Press
or
buttons to adjust the temperature. This
will override the temperature setting for two hours minimum
or until the next programmed time. To cancel the temporary
setting at any time and return to the program, press Run
Sched. If the SYSTEM button is pressed to select AUTO
the thermostat will change to Heat or Cool, whichever ran
last. If it switches to heat but you want cool, or it changes
to cool but you want heat, press both
and
buttons
simultaneously to change to the other mode.
PROGRAMMING (For Programmable Model Only)
Set Current Time and Date
1) Press MENU and then TIME button once. The display
will show the hour only.
2) Press and hold either the
or
key until you reach
the correct hour and AM/PM designation (AM begins at
midnight, PM begins at noon).
3) Press TIME once again. The display window will show
the minutes only.
4) Press and hold either the
or
key until you reach
the correct minutes.
5) Additional presses of TIME will advance the display to
show the year, month and date of month. Press the
or
key to change the display to the correct setting
for each.
6) Press RUN SCHED to exit the TIME mode.
Enter the Heating Program
1) Press SYSTEM button to select “Heat” in the system
switch area indicating the active mode being programmed.
2) Press the MENU button and then press SCHEDULE.
3) The top of the display will show the day(s) being programmed. The time and temperature (flashing) are also
displayed. “1” will also be displayed to indicate the period.
4)
5)
6)
7)
8)
9)
Press
or
key to change the temperature to your
selected temperature for the 1st heating period.
Press TIME button, time will flash.
Press
or
key to adjust the start time for the
1st period.
The time will change in 15 minute increments.
After you have set the time and the temperature for
the period to begin, press SCHEDULE to advance to the
next program period.
Repeat steps 2 through 8 until all of the program times
and temperatures are set for all program periods on that
day.
10) Press SCHEDULE to the next day and repeat steps 2
through 9.
11) When programming is complete and all of the times and
temperatures match your desired heating schedule, press
RUN SCHEDULE. The thermostat will now run your
program.
Enter the Cooling Program
1) Press SYSTEM button to select “Cool” in the system
switch area indicating the active mode being programmed.
2) Follow Enter Heating Program instructions for entering
cooling times and temperatures.
Energy Saving ENERGY STAR® Factory Pre-Program
The 1F85-0422 thermostats are programmed with the energy
saving settings shown in the table below for all days of the
week. If this program suits your needs, simply set the thermoWake Up
(Period 1)
stat clock and press the RUN SCHED button.
The table below shows the factory set heating and cooling
schedule for all days of the week.
Leave For Work
(Period 2)
Return Home
(Period 3)
Go To Bed
(Period 4)
Heating
Program
6:00 AM
70°F
8:00 AM
62°F
5:00 PM
70°F
10:00 PM
62°F
Cooling
Program
6:00 AM
75°F
8:00 AM
83°F
5:00 PM
75°F
10:00 PM
78°F
7
PROGRAMMING
Planning Your Program – Important
The Heating and Cooling Program schedules below allow you
to pencil in your own program times and temperatures.
The 1F85-0422 comes configured for 5/1/1 day programming
and can also be configured for 5/2 day programming (see
configuration section).
Factory settings are listed on Monday through Friday, Saturday and Sunday. If you are re-programming a 5/2 day schedule, pencil in your own times and temperatures directly below
the factory times and temperatures.
If you are re-programming a 5+1+1 fill in all lines with the
times and temperatures you want.
Keep the following guidelines in mind when planning your
program.
• In Heating, lower temperatures will save energy.
• In Cooling, higher temperatures will save energy.
• If you plan on using Auto Changeover, do not program the heating higher than the cooling.
Worksheet for Re-Programming 5/2 Day and 5+1+1 Day Program
Heating
Program
Wake Up
(Period 1)
Leave For Work
(Period 2)
Return Home
(Period 3)
Go To Bed
(Period 4)
6:00 AM
70°F
8:00 AM
62°F
5:00 PM
70°F
10:00 PM
62°F
Sat-Sun
or Sat
6:00 AM
70°F
8:00 AM
62°F
5:00 PM
70°F
10:00 PM
62°F
Sun
5+1+1 only
6:00 AM
70°F
8:00 AM
62°F
5:00 PM
70°F
10:00 PM
62°F
Mon-Fri
Cooling
Program
Wake Up
(Period 1)
Leave For Work
(Period 2)
Return Home
(Period 3)
Go To Bed
(Period 4)
6:00 AM
75°F
8:00 AM
83°F
5:00 PM
75°F
10:00 PM
78°F
Sat-Sun
or Sat
6:00 AM
75°F
8:00 AM
83°F
5:00 PM
75°F
10:00 PM
78°F
Sun
5+1+1 only
6:00 AM
75°F
8:00 AM
83°F
5:00 PM
75°F
10:00 PM
78°F
Mon-Fri
TROUBLESHOOTING
Comfort Alert Codes
The Comfort Alert diagnostics product monitors the air
conditioning outdoor systems with single phase Copeland
Scroll compressors. Abnormal system and electrical
conditions are indicated by flashing ALERT codes on the
yellow LED on the Comfort Alert module. The flash codes are
transmitted to the thermostat by the Comfort Alert Thermostat
interface module. The Comfort Alert compatible thermostat
displays “Call For Service” that flashes at the same rate as
the yellow LED on the Comfort Alert module.
8
Comfort Alert Yellow Alert Codes
1 Flash
Long run time
2 Flashs
System pressure trip
3 Flashs
Short cycling
4 Flashs
Locked rotor
5 Flashs
Open circuit
6 Flashs
Open start circuit
7 Flashs
Open run circuit
8 Flashs
Welded Contactor
9 Flashs
Low voltage
TROUBLESHOOTING
Reset Operation
Note: When thermostat is reset, installer configuration menu
settings and programming will reset to factory settings.
If a voltage spike or static discharge blanks out the display
or causes erratic thermostat operation, you can reset the
thermostat by removing the wires from terminals R and C
(do not short them together) and removing batteries for 2
minutes. After resetting the thermostat, replace the wires and
batteries. If the thermostat has been reset and still does not
function correctly contact your heating/cooling service person
or place of purchase.
Note: Be sure to review the installer configuration menu
settings.
To reset the programming, clock and configuration settings,
press
and
and the FAN button simultaneously. The
thermostat should go blank and then all segments will be
displayed momentarily.
Symptom
Possible Cause
Correction Action
No Heat/No Cool/No Fan
(common problems)
1.Blown fuse or tripped circuit breaker.
2.Furnace power switch to OFF.
3.Furnace blower compartment door or
panel loose or not properly installed.
4.Loose connection to thermostat or
system.
Replace fuse or reset breaker.
Turn switch to ON.
Replace door panel in proper position to engage safety
interlock or door switch.
Tighten connections.
No Heat
1.Pilot light not lit.
2.Furnace Lock-Out Condition. Heat
may also be intermittent.
Re-light pilot.
Many furnaces have safety devices that shut down when
a lock-out condition occurs. If the heat works intermittently
contact the furnace manufacturer or local HVAC service
person for assistance.
Diagnostic: Set SYSTEM Switch to HEAT and raise the
setpoint above room temperature. Within a few seconds
the thermostat should make a soft click sound. This sound
usually indicates the thermostat is operating properly. If
the thermostat does not click, try the reset operation listed
above. If the thermostat does not click after being reset
contact your heating and cooling service person or place
of purchase for a replacement. If the thermostat clicks,
contact the furnace manufacturer or a HVAC service
person to verify the heating is operating correctly.
3.Heating system requires service or
thermostat requires replacement.
No Cool
1.Cooling system requires service or
thermostat requires replacement.
Same as diagnostic for No Heat condition except set the
thermostat to COOL and lower the setpoint below the room
temperature. There may be up to a five minute delay before
the thermostat clicks in Cooling.
1.Possible short in wiring.
2.Possible short in thermostat.
3.Possible short in heat/cool/fan system.
4.FAN Switch set to Fan ON.
Check each wire connection to verify they are not shorted
or touching together. No bare wire should stick out from
under terminal block. Try resetting the thermostat as
described above. If the condition persists the manufacturer
of your system or service person can instruct you on how
to test the Heat/Cool system for correct operation. If the
system operates correctly, replace the thermostat.
Thermostat Setting &
Thermostat Thermometer
Disagree
1.Thermostat thermometer setting
requires adjustment.
The thermometer can be adjusted +/- 4 degrees. See
Temperature Display Adjustment in the Configuration Menu
section.
Furnace (Air Conditioner)
Cycles Too Fast or Too
Slow (narrow or wide
temperature swing)
1.The location of the thermostat and/or
the size of the Heating System may
be influencing the cycle rate.
Digital thermostats provide precise control and cycle faster
than older mechanical models. The system turns on and off
more frequently but runs for a shorter time so there is no
increase in energy use. If you would like an increased cycle
time, choose SL for slow cycle in the Configuration menu,
step 6 (heat), 7 (cool) or 8 (heat pump). If an acceptable
cycle rate is not achieved, contact a local HVAC service
person for additional suggestions.
Heat, Cool or Fan
Runs Constantly
Forgot Keypad Lockout
Code
Hold MENU key for 20 seconds and the lockout will reset.
9
NOTES
10
NOTES
11
Homeowner Help Line: 1-800-284-2925
White-Rodgers is a division
of Emerson Electric Co.
The Emerson logo is a
trademark and service mark
of Emerson Electric Co.
12
www.white-rodgers.com
www.emersonclimate.com