Casio LK-33 User`s guide

2012年12月25日 火曜日 午後12時15分
This recycle mark indicates that the packaging conforms to
the environmental protection legislation in Germany.
Esta marca de reciclaje indica que el empaquetado se
ajusta a la legislación de protección ambiental en Alemania.
LK-160
LK-165
LK-240
LK-247
USER’S GUIDE
Please keep all information for future reference.
Safety Precautions
Before trying to use the Digital Keyboard, be sure to
read the separate “Safety Precautions”.
GUÍA DEL USUARIO
Guarde toda información para tener como referencia futura.
Precauciones de seguridad
Antes de intentar usar el teclado digital, asegúrese de
leer las “Precauciones de seguridad” separadas.
K
MA1301-B Printed in China
LK240/165-ES-1B
ES
English
1 ページ
Español
LK240_es_Cover1-4.fm
LK240_es_Cover1-4.fm
2 ページ
2012年12月25日 火曜日 午後12時15分
B
O : Yes
X : No
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
Remarks
Aux
Messages
O
O
X
O
O
X
X
O
X
O
X
X
: All sound off
: Reset all controller
: Local ON/OFF
: All notes OFF
: Active Sense
: Reset
X
X
O
O
: Clock
: Commands
System
Real Time
X
X
X
X
X
X
: Song Pos
: Song Sel
: Tune
System
Common
O *2
O 0 - 127
O *2
O 0 - 127
Hold 1
Sostenuto
Soft pedal
Reverb send
RPN LSB, MSB
System Exclusive
After
Touch
Control
Change
Pitch Bender
Velocity
Note
Number
● Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your own, personal
use, any other use of the contents of this manual without the consent of CASIO is prohibited under copyright laws.
● IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION) ARISING OUT OF THE
USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
● The contents of this manual are subject to change without notice.
● The actual appearance of the product may be different from that shown in the illustrations in this User’s Guide.
● Company and product names used in this manual may be registered trademarks of others.
:True #
Key’s
Ch’s
Note OFF
Note ON
True voice
Default
Messages
Altered
Mode
Responsible within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
Program
Change
O
X
X
O
O
X
0, 32
1
6, 38
7
10
11
X
X
X
O 9nH v = 100 (LK-160/165)
1-127 (LK-240/LK-247)
X 9nH v = 0
36 - 96
Mode 3
X
1
1 - 16
Manufacturer:
CASIO COMPUTER CO.,LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Default
Changed
Function
This mark applies in EU countries only.
Basic
Channel
Model: LK-160/LK-165/LK-240/LK-247
Transmitted
• Before using the optional AD-E95100L Adaptor to power the unit, be sure to check the AC Adaptor for any damage first.
Carefully check the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC
adaptor that is seriously damaged.
• Never attempt to recharge batteries.
• Do not use rechargeable batteries.
• Never mix old batteries with new ones.
• Use recommended batteries or equivalent types.
• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated near the battery compartment.
• Replace batteries as soon as possible after any sign they are getting weak.
• Do not short-circuit the battery terminals.
• The product is not intended for children under 3 years.
• Use only CASIO AD-E95100L adaptor.
• The AC adaptor is not a toy.
• Be sure to disconnect the AC adaptor before cleaning the product.
O
O
O
O
O *2
O (MSB only)
O
O *2
O
O
O
O
X
O
X 9nH v = 0, 8nH v =**
Please note the following important information before using this product.
O 9nH v = 1 - 127
0 - 127
0 - 127 *1
Mode 3
X
1 - 16
1 - 16
Recognized
Important!
O *3
O *3
O *3
X
X
Bank select
Modulation
Data entry
Volume
Pan
Expression
Declaration of Conformity
Model Number: LK-160/LK-165/LK-240/LK-247
Trade Name: CASIO COMPUTER CO., LTD.
Responsible party: CASIO AMERICA, INC.
Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
64
66
67
91
100, 101
Remarks
Version : 1.0
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
*1: Depends on tone.
*1: Depende del tono.
*2: For details about NRPN, RPN, and system exclusive *2: Para obtener información acerca de NRPN, RPN y
messages, see MIDI Implementation at
los mensajes exclusivos del sistema, consulte
http://world.casio.com/.
Implementación MIDI en http://world.casio.com/.
*3: In accordance with pedal effect setting.
*3: De acuerdo con el ajuste de efecto de pedal.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
LK240_01_eTOC.fm
1 ページ
2012年12月25日 火曜日 午後12時8分
General Guide .................................. E-2
bq
Using the 10-key Pad ( )..................................... E-4
Using the FUNCTION Button ( ) ......................... E-4
3
Using Built-in Songs to
Master Keyboard Play ................... E-20
Phrases ................................................................ E-20
Step Up Lesson Flow ........................................... E-20
Selecting the Song, Phrase, and
Part You Want to Practice .................................... E-21
Lessons 1, 2, and 3 .............................................. E-22
Lesson Settings .................................................... E-23
Using Auto Step Up Lesson ................................. E-24
Getting Ready to Play...................... E-5
Preparing the Music Stand ..................................... E-5
Power Supply ......................................................... E-5
Playing the Digital Keyboard .......... E-6
Turning on Power and Playing ............................... E-6
Using Headphones ................................................. E-7
Changing Keyboard Response to
Touch Pressure (Touch Response)
(LK-240/LK-247 only) ............................................. E-7
Turning Off Keyboard Lighting................................ E-8
Using the Voice Pads ............................................. E-8
Using the Metronome ............................................. E-9
Controlling the
Keyboard Sounds .......................... E-10
Select from a variety of
musical instrument sounds ................................... E-10
Using Reverb........................................................ E-11
Using a Pedal ....................................................... E-11
Changing the Pitch (Transpose, Tuning).............. E-12
Sampling a Sound and Playing It on the
Keyboard (Sampling)............................................ E-12
Using a Sampled Sound in a Rhythm
(Drum Assign)....................................................... E-15
Music Challenge
Keyboard Game ............................. E-26
Using Auto Accompaniment......... E-28
Playing the Rhythm Part only ............................... E-28
Playing All Parts ................................................... E-29
Using Auto Accompaniment Effectively................ E-31
Using One-Touch Preset ...................................... E-32
Connecting External Devices ....... E-33
Connecting a Computer........................................ E-33
MIDI Settings ........................................................ E-34
Connecting to Audio Equipment ........................... E-36
Reference ....................................... E-37
Troubleshooting.................................................... E-37
Specifications ....................................................... E-39
Operating Precautions.......................................... E-40
Song List............................................................... E-41
Fingering Guide .................................................... E-42
Chord Example List .............................................. E-43
Playing Built-in Songs................... E-16
Playing the Demo Songs ...................................... E-16
Playing Back a Particular Song ............................ E-16
B
MIDI Implementation Chart
Included Accessories
Separately Available Accessories
● Music Stand
● Song Book
● Leaflets
• Safety Precautions
• Appendix
• Other (Warranty, etc.)
Items included as accessories are subject to change without notice.
• You can get information about accessories that
are separately for this product from the CASIO
catalog available from your retailer, and from the
CASIO website at the following URL.
http://world.casio.com/
E-1
English
Contents
LK240_02_e.fm
2 ページ
2012年12月25日 火曜日 午後12時9分
General Guide
• In this manual, the term “Digital Keyboard” refers to the LK-160/LK-165/LK-240/LK-247.
• In this manual, buttons and other controllers are identified using the numbers shown below.
• There is a button number reference at the back of this manual. You can tear it out and refer to the button numbers as required.
1
2
3
4
5
7
8
9
6
bk
bl
bm
bn
br
cn
co
cs
E-2
bs
cp
bo bp
bt
cq cr
bq
ck
cl
cm
cn
ct
B
LK240_02_e.fm
3 ページ
2012年12月25日 火曜日 午後12時9分
General Guide
• The following explains the meaning of the $ symbol that appears on the product console and with the key names below.
1 POWER button ☞E-6
2 VOLUME slider ☞E-6
3 FUNCTION, $ KEY LIGHT button ☞E-4
4 SAMPLING button ☞E-13
5 METRONOME, $ BEAT button ☞E-9
6 TEMPO buttons ☞E-9, 18, 32
7 REPEAT, INTRO button ☞E-17, 31
8 REW, NORMAL/FILL-IN button ☞E-17, 31
9 FF, VAR./FILL-IN button ☞E-17, 31
bk PAUSE, SYNCHRO/ENDING button ☞E-17, 31
bl PLAY/STOP, START/STOP button ☞E-17, 28
bm PART SELECT, ACCOMP, $ CHORDS button
English
$ : Indicates a function that is enabled by holding down the button for some time.
bp SONG BANK button ☞E-16
bq Number buttons, [–]/[+] keys ☞E-4
br LISTEN, VOICE PAD1 button ☞E-8, 22
bs WATCH, VOICE PAD2 button ☞E-8, 22
bt REMEMBER, VOICE PAD3 button ☞E-8, 23
ck NEXT, VOICE PAD4 button ☞E-8, 21
cl AUTO, VOICE PAD5 button ☞E-8, 24
cm MUSIC CHALLENGE, SET SELECT button
☞E-8, 26
cn Speakers
co Song Bank list
cp Display
cq Rhythm list
cr Tone list
cs CHORD root names ☞E-29
ct Percussion instrument list ☞E-10
☞E-19, 29
bn TONE button ☞E-10
bo RHYTHM, ONE TOUCH PRESET $ button
☞E-28, 32
■ Back
dk
dl
dk USB port ☞E-33
dl SUSTAIN jack ☞E-11
B
dm
dn
do
dp
dq
dm MIC VOLUME knob ☞E-12
dn MIC IN/SAMPLING jack ☞E-12
do AUDIO IN jack (LK-240/LK-247 only) ☞E-36
dp DC 9.5V terminal ☞E-5
dq PHONES/OUTPUT jack ☞E-7, 36
E-3
LK240_02_e.fm
4 ページ
2012年12月25日 火曜日 午後12時9分
General Guide
Using the 10-key Pad (
bq)
Use the number buttons and the [–] and [+] keys to change
the settings of the parameters that appear in the upper left
area of the display.
3
Using the FUNCTION Button ( )
Use the FUNCTION button (3) to access settings that let
you select the reverb type, pedal effect, etc.
1. Press 3 (FUNCTION).
Setting
Setting
Trans .
Md e r nPn o
Parameter
Number Buttons
2. Next press 3 (FUNCTION) until the parameter
whose setting you want to change is displayed.
Use the number buttons to enter numbers and values.
• Enter the same number of digits as the currently displayed
value.
Example: To enter tone number 004, input 0 3 0 3 4.
• Negative values cannot be input using the number buttons.
Use [+] (increase) and [–] (decrease) instead.
[–] and [+] Keys
You can use the [+] (increase) and [–] (decrease) keys to
change the displayed number or value.
• Holding down either key scrolls the displayed setting.
• Pressing both keys at the same time will revert to the initial
default setting or the recommended setting.
3
Each press of
(FUNCTION) cycles through the
available parameters.
Parameter
Display
See Page
1
Transpose
Trans.
E-12
2
Accompaniment Volume
AcompVol
E-32
3
Song Volume
Song Vol
E-18
4
Touch Response
(LK-240/LK-247 only)
Touch
E-7
5
Tuning
Tune
E-12
6
Reverb
Reverb
E-11
7
Voice Fingering Guide
Speak
E-23
8
Note Guide
NoteGuid
E-24
9
Performance Evaluation
Scoring
E-24
10 Phrase
PhraseLn
E-24
11 Sampling Start
SmplAuto
E-14
12 Keyboard Channel
Keybd Ch
E-34
13 Navigate Channels
Navi. Ch
E-34
14 Local Control
Local
E-35
15 Accomp Out
AcompOut
E-35
16 Pedal Effect
Jack
E-11
17 Power On Alert
Demo2
E-6
3. When the parameter you want is displayed, use
bq (10-key) to change its setting.
• The parameter setting will disappear from the upper left
area of the screen if you do not perform any operation
for some time.
• The tone and other parameters revert to their initial
defaults whenever you turn on power (page E-6).
E-4
B
LK240_e.book
5 ページ
2011年4月15日 金曜日 午前11時51分
Preparing the Music Stand
Music stand
English
Getting Ready to Play
Using Batteries
• Be sure to turn off power before loading batteries.
• It is up to you to prepare six commercially available
AA-size batteries. Do not use oxyride batteries or any
other nickel based batteries.
1. Open the battery cover on the bottom of the
Digital Keyboard.
Power Supply
Either an AC adaptor or batteries can be used to power this
Digital Keyboard. Normally, use of AC adaptor power is
recommended.
• The AC adaptor does not come with this Digital Keyboard.
Purchase it separately from your retailer. See page E-1 for
information about options.
2. Load six AA-size batteries into the battery
compartment.
Make sure the positive + and negative - ends of the
batteries are facing as shown in the illustration.
Using the AC Adaptor
Make sure that you use only the AC adaptor specified for this
Digital Keyboard. Use of a different type of AC adaptor can
cause malfunction.
Specified AC Adaptor: AD-E95100L
(JEITA Standard plug)
Household power outlet
DC 9.5V terminal
3. Insert the tabs of the battery cover into the
holes on the side of the battery compartment,
and close the cover.
Tabs
AC adaptor
• Be sure to turn off Digital Keyboard power before
connecting or disconnecting the AC adaptor.
• The AC adaptor will become warm to the touch after
very long use. This is normal and does not indicate
malfunction.
• To prevent breaking of the wire, take care to avoid
putting any type of load on the power cord.
No bending!
No winding!
■ Low Battery Indication
The indicator shown below starts to flash to let you know
when battery power is low. Replace the batteries with new
ones.
Low battery indicator
(flashes)
• Never insert metal, pencils, or any other objects into
the product’s 9.5V DC terminal. Doing so creates the
risk of accident.
E-5
LK240_02_e.fm
6 ページ
2011年4月18日 月曜日 午後4時20分
Playing the Digital Keyboard
1 2 3
5
bnbo
6
bq
br bs bt ck cl cm
Turning on Power and Playing
1. Press 1.
This turns on power.
• To turn off the Digital Keyboard, press
1 again.
2. Try playing something on the keyboard. Use 2
to adjust volume.
Power On Alert (Using the AC Adaptor)
While you are using the AC adaptor for power, the keyboard
keys will light to remind you that power is on if you do not
perform any operation for about six minutes. Power on alert is
disabled while batteries are being used for power.
■ Disabling Power On Alert
You can disable power on alert to ensure that keyboard keys
do not light during a concert, etc.
Increase
1. Press 3 (FUNCTION) a number of times until
“Demo2” appears on the display (page E-4).
Decrease
Demo 2
• Turning off the Digital Keyboard power causes all
current settings and sampled sounds (page E-12) to be
cleared. The Digital Keyboard will revert to initial
default settings the next time you turn it on.
Auto Power Off
If you do not perform any operation on the Digital Keyboard
for one of the trigger times noted below, Auto Power Off will
turn off power.
During battery operation
: 6 minutes
During AC adaptor operation : 30 minutes
■ Disabling Auto Power Off
You can disable Auto Power Off to ensure that power is not
turned off automatically during a concert, etc.
1. While holding down bn (TONE), turn on power.
Auto Power Off will be disabled.
E-6
2. Press the bq (10-key) [–] key to select the OFF
setting.
LK240_02_e.fm
7 ページ
2012年12月25日 火曜日 午後12時12分
Using Headphones
Using headphones cuts off output from the built-in speakers,
which means you can practice playing even late at night
without disturbing others.
• Be sure to turn down the volume level before connecting
headphones.
Changing Keyboard Response to
Touch Pressure (Touch Response)
(LK-240/LK-247 only)
Touch Response alters tone volume in accordance with
keyboard pressure (speed). This provides you some of the
same expressivity you get on an acoustic piano.
Pressing fast produces
louder notes.
PHONES/OUTPUT jack
• Headphones do not come with the Digital Keyboard.
• Use commercially available headphones. See page E-1 for
information about options.
Pressing slowly produces
softer notes.
• Do not listen to very high volume output over
headphones for long period. Doing so creates the risk
of hearing damage.
• If you are using headphones that require an adaptor
plug, make sure you do not leave the adaptor plugged
in when removing the headphones.
Do not try to use too much
pressure.
Changing Touch Response Sensitivity
Use the procedure below to control how much the volume of
played notes change in accordance with playing speed.
Select the setting that best matches your playing style.
1. Press 3 (FUNCTION) a number of times until
“Touch” appears on the display (page E-4).
Touch
2. Use bq (10-key) [–] and [+] keys to select one of
the three Touch Response sensitivity settings.
B
Off (oFF)
Touch Response is turned off. Sound
volume is fixed, regardless of key press
speed.
Type 1 (1)
Normal Touch Response
Type 2 (2)
More sensitive Touch Response than Type 1
E-7
English
Playing the Digital Keyboard
LK240_02_e.fm
8 ページ
2011年4月22日 金曜日 午前9時55分
Playing the Digital Keyboard
Turning Off Keyboard Lighting
2. Press a pad (1 through 5, br through cl) to
sound what is assigned to it.
Keyboard Lighting causes keyboard keys to light when you
press them, during built-in song playback, etc. You can use
the following procedure to turn off Keyboard Lighting.
There are four sets of voice pad sounds numbered 1
cycles through
through 4 (see below). Each press of
the sound sets 1 through 4.
1. Hold down 3 (FUNCTION) until “Keylight”
br
appears on the display.
cm
bs
bt
ck
cl
cm
Key l i gh t
2. Press the bq (10-key) [–] key to select the OFF
setting.
Set 1
Using the Voice Pads
You can use the voice pads to sound various sound effects or
even sounds you have sampled (“Sampling”, page E-12). Use
the voice pads to add something extra to your performances.
1. Press bo (RHYTHM).
Lights
Pad 1
Pad 2
Pad 3
TONE 402
“VOICE
PAD 1”
TONE 403
“VOICE
PAD 2”
TONE 404
“VOICE
PAD 3”
Set 2
Set 1 sounds with various pitches.*2
Set 3
Set 1 sounds repeated.*3
Set 4
XIAO LUO
GUNSHOT
BONGO
Pad 4
Pad 5
TONE 401 “ORIGINAL” *1
CONGA
TAMBOURINE
*1: Pad 5 plays original sound raised a perfect fifth.
*2: Pad 1: Up a perfect fifth; Pad 2: Down a perfect fifth;
Pad 3: Same as Set 1; Pad 4: Up a major third;
Pad 5: Down a perfect fifth
*3: Pads 1 and 5: Gradually rising pitch;
Pad 2: Gradually falling pitch
Example: When Set 2 is selected
Pad Se t
• While a sound set number is displayed, you can change it
(10-key). If you do not perform any operation for a
using
few seconds after the indicator appears, the display will
return to the previous screen automatically.
bq
Sounding Sampled Sounds with the Voice
Pads
Sampling sounds will change the tones assigned to sets 1
through 3 to the sampled sounds. For more information, see
page E-12.
E-8
LK240_e.book
9 ページ
2011年4月15日 金曜日 午前11時51分
Playing the Digital Keyboard
Changing the Metronome Tempo
The metronome lets you play and practice along with a steady
beat to help keep you on tempo.
Use the following procedure to change the tempo of the
metronome.
English
Using the Metronome
1. Press 6.
Start/Stop
Use w (slower) and q (faster) to change the tempo
setting. Holding down either button changes the setting at
high speed.
• Pressing w and q at the same time will initialize the
tempo setting in accordance with the currently selected
song or rhythm.
• Pressing
causes the tempo value to flash on the
display. While the tempo value is flashing, you can use
(10-key) to change it.
Note that you must input leading zeros, so 89 is input
as 089.
• The tempo value will stop flashing if you do not perform
any operation for a short while.
1. Press 5.
This starts the metronome.
This pattern changes with each beat.
6
bq
2. Press 5 again to stop the metronome.
Changing the Beats per Measure
Tempo value (flashes)
You can configure the metronome to use a bell sound for the
first beat of each measure of the song you are playing.
• You can specify 0, or a value from 2 to 6 as the number of
beat per measure.
• When playing a built-in song, the beats per measure setting
(which determines when the bell sounds) is configured
automatically for the currently selected song.
1. Hold down 5 until the beats per measure
setting screen appears on the display.
Changing the Metronome Sound Volume
The metronome volume setting is changed automatically with
the volume level of the currently selected Auto
Accompaniment or song. The metronome volume cannot be
adjusted independently.
• For information about changing the Auto Accompaniment
volume, see page E-32.
• For information about changing the song volume, see page
E-18.
Bea t
• If you do not perform any operation for after the beats
per measure setting screen appears, the display will
return to the screen displayed before you pressed
.
• You cannot adjust the balance between the metronome
and note volume during Auto Accompaniment and built-in
tune play.
5
2. Use bq (10-key) to enter the number of beats
per measure.
• The bell will not sound if you specify 0 for this setting. In
this case, all beats are indicated by a click sound. This
setting lets you practice with a steady beat, without
worrying how many beats there are in each measure.
E-9
LK240_02_e.fm
10 ページ
2012年12月25日 火曜日 午後12時12分
Controlling the Keyboard Sounds
bnbo
3 4
bq
br bs bt ck cl
Select from a variety of musical
instrument sounds
3. Try playing something on the keyboard.
The tone of the instrument you selected will sound.
Your Digital Keyboard lets you select tones for a wide variety
of musical instrument sounds, including violin, flute, orchestra,
and more. Even the same song sound takes on a different feel
by changing the instrument type.
To select an instrument for playing
1. Press bn (TONE).
Tone number
Playing with a Piano Tone (Piano Setup)
bn
bo
Press
(TONE) and
(RHYTHM) at the same time.
This selects the grand piano tone.
S t .GrPno
Tone name
2. Use bq (10-key) to select the tone number you
want.
The corresponding tone number and tone name will
appear on the screen.
• Use the number buttons to enter the tone number.
Specify three digits for the tone number.
Example: To select 001, enter 0 3 0 3 1.
Settings
Tone Number:
“001”
Reverb:
“06”
Transpose:
“00”
Touch Response (LK-240/LK-247 only):
Off: Returns to initial default
On: No change
Pedal Effect:
SUS
Rhythm Number: “131”
Accompaniment: Rhythm part only
Local Control:
On
Drum Assign:
Off
• See the separate “Appendix” for a complete list of available
tones.
• When one of the drum sets is selected (tone numbers 395
through 400), each keyboard key is assigned a different
percussion sound.
E-10
B
LK240_02_e.fm
11 ページ
2011年4月18日 月曜日 午後4時21分
Controlling the Keyboard Sounds
Using a Pedal
Reverb adds reverberation to notes. You can change the
duration of the reverb.
1. Press 3 (FUNCTION) a number of times until
“Reverb” appears on the display (page E-4).
A pedal can be used to change notes in various ways while
playing.
• A pedal unit does not come with the Digital Keyboard.
Purchase one separately from your retailer. See page E-1
for information about options.
Connecting a Pedal Unit
Re v e r b
Connect an optional pedal unit.
2. Use the bq (10-key) [–] and [+] keys to select
the reverb setting you want.
Off (oFF)
Turns off reverb.
1 to 10
The larger the number selected, the longer
the reverb duration.
SUSTAIN jack
Selecting the Pedal Effect
1. Press 3 (FUNCTION) a number of times until
“Jack” appears on the display (page E-4).
Re v e r b
Jack
2. Use the bq (10-key) [–] and [+] keys to select
the pedal effect you want.
Indicator disappears when
reverb is turned off.
• The following shows the available pedal effects.
Sustain
(SUS)
Sustains notes played while the pedal is
depressed. Organ and other similar tone
notes are sustained even if the pedal is not
pressed.
Sostenuto
(SoS)
Sustains notes that are playing when the
pedal is depressed before the keyboard
keys are released.
Soft
(SFt)
Slightly softens notes played while the pedal
is depressed.
Rhythm
(rHy)
Pressing the pedal starts and stops Auto
Accompaniment or song playback.
E-11
English
Using Reverb
LK240_02_e.fm
12 ページ
2011年4月18日 月曜日 午後4時21分
Controlling the Keyboard Sounds
Changing the Pitch
(Transpose, Tuning)
Changing the Pitch in Semitone Steps
(Transpose)
The transpose feature lets you change the pitch, in semitone
steps. A simple operation lets you instantly change the pitch
to match that of a singer.
• The transpose setting range is –12 to +12 semitones.
1. Press 3 (FUNCTION).
Sampling a Sound and Playing It
on the Keyboard (Sampling)
You can use the Digital Keyboard to sample a sound from a
microphone, and then play the sound with the keyboard keys
or voice pads. For example, you could sample the bark of
your dog and then use the sound in a melody. The sampling
feature is a great way to create new sounds that are highly
creative.
Connection
Connect a microphone.
Trans .
MIC IN/SAMPLING jack
2. Use the bq (10-key) [–] and [+] keys to select
the transpose setting you want.
Fine Tuning (Tuning)
• Use of a commercially available microphone also is
supported.
Use the tuning feature when you need to adjust the pitch
slightly to play along with another musical instrument. Also,
some artists perform their music with slightly altered tuning.
You can use the tuning feature to adjust tuning so it exactly
matches a performance on a CD.
• The tuning feature specifies the frequency of the A4 note.
You can set a frequency within the range of 415.5 to
465.9 Hz. The initial default setting is 440.0 Hz.
• Turn off the microphone and the Digital Keyboard
before connecting them.
• It will take a few seconds before you can use the
microphone after you turn on the Digital Keyboard.
• Sampled sounds are recorded in monaural.
• You cannot sample sounds input from through the
AUDIO IN jack.
1. Press 3 (FUNCTION) a number of times until
Sampling a Sound and Playing It
“Tune” appears on the display (page E-4).
There are two sampling methods: full sampling and short
sampling.
■ Full Sampling
Tune
This method allows sampling of a single sound with a duration
of one second.
1. Turn the volume levels of the Digital Keyboard
2. Use the bq (10-key) [–] and [+] keys to adjust
the tuning.
• Performing this step causes the display to change from
“Tune” to a value that indicates the current frequency
setting as shown below. You can change the frequency
in 0.1Hz steps.
down.
2. Turn on the microphone and then the Digital
Keyboard.
3. Use dm (MIC VOLUME) to adjust the volume
level of microphone input.
440 . 0Hz
bq
(10-key) operation to
• Even if you do not perform a
adjust the tuning, the current frequency setting will
appear automatically after a few seconds.
E-12
LK240_e.book
13 ページ
2011年4月15日 金曜日 午前11時51分
Controlling the Keyboard Sounds
This enters record standby.
■ Short Sampling
With short sampling, you can sample up to three sounds,
each one with a duration of approximately 0.3 seconds. You
can sound the short sampled sounds using voice pads
1 through 3.
Wa i t i n g
1. Connect a microphone to the Digital Keyboard.
Refer to steps 1 through 2 under “Full Sampling” (page
E-12).
2. While holding down 4, press the voice pad
Flashes
br bs
bt
( ,
, or
) that corresponds to the tone
number where you want to store the sound.
• The relationship between tone numbers and voice pads
is shown below.
5. Output the sound in the direction of the
microphone.
The Digital Keyboard will start sampling automatically,
and stop after one second.
• Sampling will not start if the volume of the sound picked
up by the microphone is too low.
• What you sample is stored as tone number 401.
Samp l i n g
Flashes
Selected Tone
Number
402
403
404
Pressed Voice Pad
Pad 1
( )
Pad 2
( )
Pad 3
( )
br
bs
Example: When voice pad 3 (Tone Number 404) is
selected
Vo i . Pad3
Flashes
Record standby is entered when you release
Or i g i na l
bt
4.
Wa i t i n g
Lights
Flashes
6. Try playing something on the keyboard.
ck or cl) to sound the
• You can press pad 4 or 5 (
sampled sound (page E-8).
• A new sample replaces sample data currently assigned to
tone number 401. All of the old data (including short
sampled sounds) is deleted.
E-13
English
4. Press 4 and immediately release it.
LK240_e.book
14 ページ
2011年4月15日 金曜日 午前11時51分
Controlling the Keyboard Sounds
3. Output the sound in the direction of the
microphone.
Sampling starts automatically and stops after about 0.3
seconds.
• Sampling will not start if the volume of the sound picked
up by the microphone is too low.
Turning off power clears sampled data!
Turning off power will causes all sampled sound data to be
deleted.
■ How sampled sounds are played
Pressing Middle C (C4) will play back the original sound. The
keys to the left and right of C4 play the sound at different
pitches.
Vo i . Pad3
C4
Lights
br
Set 1 of voice pads 1 through 4 (
through
sampled sounds without modification.
ck) produce
Starting a Sampling Operation Manually
4. Try playing something on the keyboard.
• You also can sound the sampled sound by pressing the
voice pad you pressed in step 2.
1. Press 3 (FUNCTION) a number of times until
“SmplAuto” appears on the display (page E-4).
Smp l A u t o
• Sampling a new sound deletes the sound assigned to the
same tone number and the full sampling sound (page
E-12).
2. Press bq (10-key) [–] key to select the OFF
setting.
This enables manual sampling. When this setting is
selected, sampling starts as soon as you release
in
step 4 under “Full Sampling” (page E-12) or step 2 under
“Short Sampling” (page E-13).
4
• When the above setting is “oFF”, sampling starts when
you release
, not when you press it. Sampling will
not start if you keep
depressed.
4
E-14
4
LK240_e.book
15 ページ
2011年4月15日 金曜日 午前11時51分
Applying Effects to a Sampled Sound
You can use the following procedure to apply various settings
to the sampled tone assigned to tone number 401.
1. Use bq (10-key) to select a tone number from
405 to 414.
Tone numbers 405 to 414 actually represent effects
assigned to tone number 401. Selecting a tone will play
the sampled sound in a loop, along with the applicable
effect, as described below.
Tone
No.
405
Effect
Name
Use the following procedure to replace a percussive
instrument with a sampled sound you sampled with short
sampling and play auto accompaniment rhythms (page E-28)
with it.
1. Press 3 (FUNCTION) and 4 at the same time.
Description
Loop 1
Loops the sampled sound.
406
Loop 2
Loops the sample sound and raises the
pitch of the resonating sound when the
keyboard key is released.
407
Loop 3
Loops the sample sound and lowers
the pitch of the resonating sound when
the keyboard key is released.
408
Pitch 1
Changes the pitch from low to high, at
an increasing rate.
409
Pitch 2
Changes pitch from high to low, at a
decreasing rate.
Pitch 3
Changes pitch from high to low, at a
decreasing rate, and then raises the
pitch when the key is released.
410
Using a Sampled Sound in a
Rhythm (Drum Assign)
411
Tremolo
Alternates volume between high and
low.
412
Funny 1
Adds vibrato and changes pitch by a
gradually increasing amount.
413
Funny 2
Alternates between high pitch and low
pitch.
414
Funny 3
Adds vibrato and changes pitch from
low to high.
D r mA s i g n
Lights
The display will return to the previous screen if you do not
perform the next step for some time.
2. Use the bq (10-key) [–] and [+] keys to select
the drum assign type you want.
Off (oFF)
Sampled sound does not sound.
Type 1 (dr1)
Replaces the bass drum of the rhythm
pattern with tone number 402, and the
snare drum with tone number 403.
Type 2 (dr2)
Replaces more of the percussive
instruments than Type 1 with tone numbers
402, 403, and 404.
3. Start rhythm play (page E-28).
The rhythm sounds in accordance with the drum assign
type you selected in step 2.
• Some rhythm part drum sounds cannot be replaced by
sampled sounds.
E-15
English
Controlling the Keyboard Sounds
LK240_02_e.fm
16 ページ
2011年4月18日 月曜日 午後4時21分
Playing Built-in Songs
3
bp
6
bq
7 8 9 bk bl bm
With this Digital Keyboard, built-in tune data is referred to as
“songs”. You can listen to the built-in songs for your own
enjoyment, or you can play along with them for practice.
• In addition to simple listening enjoyment, the built-in songs
can be used with the lesson system (page E-20) for
practice.
Playing Back a Particular Song
Use the procedure below to play back one of the built-in
songs. You can play along on the keyboard with song
playback.
Start/Stop
1. Press bp (SONG BANK).
Playing the Demo Songs
Song number
Use the following procedure to play back built-in songs (001 to
090).
1. Press bl and bm at the same time.
This will start playback of the demo songs. Demo
playback continues until you stop it.
• See page E-41 for a complete list of available songs.
• Demo playback always starts from song number 001.
Tw i n k l e
Lights
Tune name
Song number
Lights
Tw i n k l e
Flashes
2. Use bq (10-key) to enter the number of the song
Tune name
you want.
2. To change to another song while demo
bq
playback is in progress, use
(10-key) [–] and
[+] keys to enter the song number you want
(page E-4).
This will cause demo playback to jump to the song whose
number you entered.
(10-key) number buttons to select a
• You cannot use
song.
bq
3. To stop demo playback, press bl.
Demo playback continues until you stop it by pressing
E-16
bl.
• See page E-41 for a complete list of available songs.
• Use the number buttons to enter the song number.
Specify three digits for the song number.
Example: To select 001, enter 0 3 0 3 1.
LK240_e.book
17 ページ
2011年4月15日 金曜日 午前11時51分
Playing Built-in Songs
3. Press bl.
This skips song playback forward to the next measure.
Each press of
skips ahead one measure. Holding
down
skips forward at high speed until you release it.
• Pressing
while song playback is stopped performs
lesson function phrase skip forward (page E-21).
Sustain pedal
Key
Beat
1. Press 9.
Note
9
9
9
Measure
Tempo
Fingering
Measure number
■ Skip Back
4. Press bl again to stop playback.
bl to
Song playback will continue (repeat) until you press
stop it. You can cancel song repeat by pressing
.
7
1. Press 8.
This skips song playback back to the previous measure.
Each press of
skips back one measure. Holding down
skips back at high speed until you release it.
• Pressing
while song playback is stopped performs
lesson function phrase skip back (page E-21).
8
8
8
Repeating Playback of Specific Measures
Indicator disappears when song repeat
is turned off.
Pause, Skip Forward, Skip Back
You can use the procedure in this section to repeat particular
measures for practice playing along until you master it. You
can specify the start measure and the end measure of the
section you want to play and practice.
Start
End
Use the operations in this section to perform pause, skip
forward, and skip back operations.
■ Pause
1. Press bk.
This pauses song playback.
These measures are repeated.
1. Press 7 to temporarily turn off song repeat.
2. Press bk again to resume playback from the
point where you paused it.
Disappears
E-17
English
■ Skip Forward
This starts playback of the song. Keyboard keys will light
as notes are played.
LK240_e.book
18 ページ
2011年4月15日 金曜日 午前11時51分
Playing Built-in Songs
2. When song playback reaches the measure you
want to specify as the start measure, press
7.
This specifies the measure as the start measure.
Changing Playback Speed (Tempo)
You can use the following procedure to change the speed
(tempo) in order to slow down playback to practice difficult
passages, etc.
1. Press 6.
6
Flashes
3. When playback reaches the measure you want
to select as the end measure, press
7 again.
This specifies the measure as the end measure and starts
repeat playback of the measures in the specified range.
• During repeat play you can use
to pause playback,
to skip forward, or
to skip back.
9
8
Use w (slower) and q (faster) to change the tempo
setting. Holding down either button changes the setting at
high speed.
• Pressing w and q at the same time will return the
current song to its original default tempo.
• Pressing
causes the tempo value to flash on the
display. While the tempo value is flashing, you can use
(10-key) to change it. The tempo value will stop
flashing if you do not perform any operation for a short
while.
• Changing the song number will return the song to its
original default tempo.
bk
bq
Adjusting the Song Volume
Use the following procedure to adjust the balance between
the volume of what you play on the keyboard and song
playback volume.
1. Press 3 (FUNCTION) a number of times until
“Song Vol” appears on the display (page E-4).
Lights
4. Pressing 7 again returns to normal playback.
Changing the song number clears the start measure and
end measure of the repeat operation.
Song Vo l
2. Use the bq (10-key) [–] and [+] keys to adjust
the song volume.
Disappears
E-18
LK240_e.book
19 ページ
2011年4月15日 金曜日 午前11時51分
Playing Built-in Songs
Playing with the Tone as Song Playback
English
The procedure below lets you select the same keyboard tone
as the one being used in the song and play along with your
favorite tunes.
1. After selecting a song, hold down bp (SONG
BANK) for about two seconds until the
displayed tone name changes to the tone name
of the song.
• If your currently selected tone is the same as the song
tone, the display contents will not change.
2. Play along with song playback.
• If you select a song that uses different tones for left and
right hand play, the right hand part tone is assigned to the
keyboard.
Turning Off the Part of One Hand for Practice
(Part Select)
You can turn off the right hand part or the left hand part of a
song during playback and practice playing the along with the
remaining part.
1. Press bm to select the part you want to turn off.
Each press of
below.
bm cycles through the settings shown
Right hand part off
Left hand part off
Both hand parts off
Both hand parts on
2. Press bl.
This starts playback in accordance with the setting you
selected in step 1.
• During playback with one part turned off, only the notes of
the part that is turned off are shown on the display.
E-19
LK240_03_e.fm
20 ページ
2011年4月18日 月曜日 午後4時21分
Using Built-in Songs to Master Keyboard Play
bp
3
7 8 9
bl bm
br bs bt ck cl
To master a song, it is best to break it up into shorter parts
(phrases), master the phrases, and then put everything
together. Your Digital Keyboard comes with a Step Up Lesson
feature that helps you to do just that.
Phrases
The built-in songs are pre-divided into phrases to help you
master keyboard play.
Song start
Step Up Lesson Flow
Step Up Lesson takes you through practice of the right hand
part, left hand part, and both hand parts for each phrase of a
song. Master all of the phrases and you master the song.
Phrase 1
• Right Hand Lesson 1, 2, 3
• Left Hand Lesson 1, 2, 3
• Both Hand Lesson 1, 2, 3
Song end
4
Phrase 1
Phrase 2
Phrase 3
. . . .
Final
Phrase
Repeat the above to practice phrase
2, 3, 4, and so on, until you reach the
final phrase of the song.
4
After mastering all of the phrases,
practice the entire song.
4
Now you have mastered the entire
song!
E-20
bq
LK240_e.book
21 ページ
2011年4月15日 金曜日 午前11時51分
Using Built-in Songs to Master Keyboard Play
The following are the messages that appear on the display
during Step Lessons.
Message
<Phrase>
<Wait>
NextPhrs
From Top
Complete
Description
Appears when you select a phrase, when a
lesson starts, etc.
• Note that certain phrases will cause
“<Wait>” to appear instead of “<Phrase>”.
Appears when the lesson starts with an intro
or fill-in phrase that is not included in the
phrases to be practiced. Play toll advance
automatically to the next phrase after the unincluded phrase plays, so wait until then to
start playing on the keyboard.
Appears when advancing automatically to the
next phrase. This message appears following
a phrase for which “<Wait>” (see above) is
displayed, and during an Auto Step Up Lesson
(page E-24).
2. Press ck (or 9) to move forward one phrase,
or
8 to move back one phrase.
9 8
• Holding down
or
scrolls through phrases at high
speed.
• The Digital Keyboard remembers the last phrase you
practiced for up to 20 songs. To recall the last practice
phrase for the current song (if it is available), hold down
.
ck
Phrase number
<Ph r ase>
First measure of the selected phrase
3. Press bm to select the part you want to practice.
Each press of
below.
This message appears during Auto Step Up
Lesson (page E-24) immediately before
practice from Phrase 1 up until the phrase
currently being practiced.
bm cycles through the settings shown
Right hand practice
Appears at the end of Auto Step Up Lesson
(page E-24).
Left hand practice
Selecting the Song, Phrase, and
Part You Want to Practice
Both hand practice
First, select the song, phrase, and part you want to practice.
1. Select the song you want to practice (page
E-16).
*
This will select the first phrase of the song.
* This indicator (setting) is skipped if you press
a lesson is in progress.
bm while
4. Hold down bp (SONG BANK) for about two
seconds.
The same tone used for song playback will be assigned to
the keyboard (page E-19).
E-21
English
Messages that Appear during Lessons
LK240_e.book
22 ページ
2011年4月15日 金曜日 午前11時51分
Using Built-in Songs to Master Keyboard Play
Lessons 1, 2, and 3
Now it is time to start the lessons. First, select the song and
part you want to practice.
Lesson 1: Listen to the song.
2. Play notes on the keyboard in accordance with
the instructions provided on the display and by
voice fingering guide.
During this lesson, the display shows the key you need to
press next. Voice fingering guide uses a simulate voice to
announce which finger you should use.
First, listen to the example a few times to familiarize yourself
with what it sounds like.
1. Press br.
Flashes
This starts example play.
Lights
Lights
2. To stop Lesson 1, press br or bl.
Lesson 2: Watch how the song is played.
Play the song on the keyboard. During this lesson, the display
shows the key you need to press next. Voice fingering guide
also uses a simulate voice to announce which finger you
should use. Follow the instructions to press the correct
keyboard keys and play the notes. Don’t worry if you play the
wrong note. Song playback will wait until you play the correct
note. Take your time and play at your own pace.
<Lesson 2 Guidance>
Master playing the correct note with the correct finger
as instructed by the guidance. Practice playing with the
correct timing.
4
Song playback will wait for you to play the correct note.
• Keyboard key goes from flashing to lit.
• Note guide sounds the correct note to be played.
• Voice Fingering Guide tells you what finger to use.
1. Press bs.
This starts Lesson 2.
4
Pressing the correct keyboard key causes song
playback to resume and the key for the next note
flashes.
Lights
3. To stop Lesson 2, press bs or bl.
● If you complete Lesson 2 play to the end, a score that
rates your play appears on the screen.
E-22
Bravo!
You pass! Advance to the next lesson.
Again!
Go back and try again.
LK240_e.book
23 ページ
2011年4月15日 金曜日 午前11時51分
Using Built-in Songs to Master Keyboard Play
Though song playback stands by waiting for you to press the
correct keys as in Lesson 2, the Digital Keyboard does not
provide any guidance about what note you need to play next.
Remember everything you have learned up to Lesson 2 as
you play.
Playing a Particular Song All the Way
Through
After you successfully complete all of the phrases in Lessons
1, 2, and 3, it is time to try playing the entire song from
beginning to end.
1. Use bm to turn off both hand parts and then
press
1. Press bt.
bl.
Try playing with both hands and find out how the Digital
Keyboard evaluates your effort.
This starts Lesson 3.
Lesson Settings
Lights
Playing without Phrase Repeat
You can turn off phrase repeat for Lessons 1, 2, and 3.
2. Play the song along with the song playback.
1. Press 7.
This disables phrase repeat play.
<Lesson 3 Guidance>
Press the keyboard keys you learned in Lesson 2.
4
Tw i n k l e
Song playback will wait for you to play the correct note.
• Note guide sounds the correct note to be played.
4
If you are still unable to press the correct keyboard
key, the Digital Keyboard will display keyboard
guidance and voice fingering guide will tell you what
finger to use, just as in Lesson 2.
4
Pressing the correct key will cause song playback to
resume.
3. To stop Lesson 3, press bt or bl.
• If you complete Lesson 3 play to the end, a score that
rates your play appears on the screen the same as with
Lesson 2.
Disappears
Turning Off Voice Fingering Guide
Use the following procedure to turn off voice fingering guide,
which tells you which finger to use to play each note in
Lesson 2 and Lesson 3.
1. Press 3 (FUNCTION) a number of times until
“Speak” appears on the display (page E-4).
Speak
2. Press the bq (10-key) [–] key to select the OFF
setting.
E-23
English
Lesson 3: Remember what you learned as
you play.
LK240_e.book
24 ページ
2011年4月15日 金曜日 午前11時51分
Using Built-in Songs to Master Keyboard Play
Turning Off Note Guide
Use the following procedure to turn off note guide, which
sounds the note to be played next in Lesson 2 and Lesson 3.
1. Press 3 (FUNCTION) a number of times until
“NoteGuid” appears on the display (page E-4).
Using Auto Step Up Lesson
With Auto Step Up Lesson, the Digital Keyboard advances
through each lesson automatically.
1. Select the song and part you want to practice
(page E-16).
2. Press cl.
No t eGu i d
2. Press the bq (10-key) [–] key to select the OFF
Listen to the first phrase in Lesson 1.
• In Lesson 1, the sample phrase is played only once
before advancing to Lesson 2.
Flashes
setting.
Lights
Turning Off Performance Evaluation
Use the following procedure to turn off performance
evaluation, which evaluates your performance and displays a
score in Lesson 2 and Lesson 3.
1. Press 3 (FUNCTION) a number of times until
“Scoring” appears on the display (page E-4).
3. Auto Step Up Lesson stops automatically after
you are able to get through all of the lessons
successfully.
• In Lesson 2 and Lesson 3, the Digital Keyboard
advances to the next lesson if you are able to achieve
the “Bravo!” evaluation result.
• To cancel a lesson, press
or
.
cl bl
Sco r i ng
2. Press the bq (10-key) [–] key to select the OFF
setting.
Lesson Play without Dividing Songs into
Phrases
When the phrase function is turned off, lessons go through an
entire song from beginning to end, without dividing it up
between phrases.
1. Press 3 (FUNCTION) a number of times until
“PhraseLn” appears on the display (page E-4).
Ph r aseLn
2. Press the bq (10-key) [–] key to select the OFF
setting.
E-24
• You can change the step and phrase during Auto Step Up
Lesson using
,
, and
to
.
• Starting Auto Step Up Lesson turns on Phrase Repeat
(page E-23), Note Guide (page E-24) and Performance
Evaluation (page E-24) automatically. These features
cannot be turned off during lessons.
89
br ck
LK240_e.book
25 ページ
2011年4月15日 金曜日 午前11時51分
Using Built-in Songs to Master Keyboard Play
■ Auto Step Up Lesson Procedure
English
Phrase 1
Lesson 1
4
Lesson 2
4
Lesson 3
4
Phrase 2
Lesson 1
4
Lesson 2
4
Lesson 3
4
Phrase 1, 2
• Lesson 3*
4
Phrase 3
Lesson 1
4
Lesson 2
4
Lesson 3
4
Phrase 1, 2, 3
• Lesson 3*
4
Next phrase practice using the same
procedure
4
Final phrase
Lesson 1
4
Lesson 2
4
Lesson 3
4
From Phrase 1 to the final phrase
• Lesson 3*
4
Lesson complete
* Auto Step Up Lesson advances to the next phrase,
regardless of whether the “Bravo!” result is attained.
E-25
LK240_03_e.fm
26 ページ
2011年4月18日 月曜日 午後4時21分
Music Challenge Keyboard Game
bobp
bn
bnbo
1
bl
Music Challenge is a game that measures your reaction
speed as you press keys in response to keyboard keys that
light and to on-screen fingering guide indications.
1. Press bp (SONG BANK).
2. Press cm.
This causes a keyboard key to start flashing, and starts
the Music Challenge song.
cm
3. After the keyboard key changes from flashing
to lit, press the key with the finger indicated on
the screen as quickly as possible.
This causes the lighting of the key you press to go out,
indicating you have cleared the first note. The next key
will start flashing, so get ready to press it next.
• The time it takes you to press the keyboard key after it
lights appears on the display (Unit: 0.1sec). The shorter
the time, the higher your score.
• Pressing a key before it goes from flashing to lit, will not
advance to the next note.
0.3sec
Time
M . CHA L . !
Number of remaining notes
Displayed during a game.
Fingering
E-26
LK240_e.book
27 ページ
2011年4月15日 金曜日 午前11時51分
Music Challenge Keyboard Game
4. The game ends when you advance successfully
through 20 notes.
bn
bo
English
• Your score and playing time appear on the display.
After a short while, the playing time display changes to
an evaluation result. To clear the evaluation result from
the display, press
(TONE),
(RHYTHM), or
(SONG BANK).
• You can cancel a game at any time by pressing
or
.
bp
cm
bl
Score
T i me 1 9 . 2
Playing time
Grade :
A
Evaluation result
Evaluation Result
S
<High>
A
B
Evaluation Ranges
C
D
<Low>
• Notes and fingering guide fingers are indicated randomly.
• The tempo of the game songs cannot be changed.
• All buttons except
,
, and
are disabled while a
game is in progress.
1 bl
cm
E-27
LK240_03_e.fm
28 ページ
2011年4月18日 月曜日 午後4時21分
Using Auto Accompaniment
3
bo
6
bq
7 8 9 bk bl bm
With Auto Accompaniment, simply select an accompaniment
pattern. Each time you play a chord with your left hand the
appropriate accompaniment will play automatically. It’s like
having a personal backup group along with you wherever you
go.
Starting and Stopping the Rhythm Part only
1. Press bo (RHYTHM).
Rhythm number
• Auto Accompaniments are made up of the following three
parts.
(1) Rhythm
(2) Bass
(3) Harmony
You can have only the rhythm part play, or you can have all
three parts play at the same time.
Funk 8B t
Rhythm pattern name
2. Use bq (10-key) to select the rhythm number
you want.
Playing the Rhythm Part only
The rhythm part is the foundation each Auto Accompaniment.
Your Digital Keyboard comes with a variety of built-in rhythms,
including 8-beat and waltz. Use the following procedure to
play the basic rhythm part.
• See the separate “Appendix” for information about
individual rhythms.
• Use the number buttons to enter the rhythm number.
Specify three digits for the rhythm number.
Example: To select 001, enter 0 3 0 3 1.
3. Press bl or 8.
This starts the rhythm.
This pattern changes with each beat.
4. Play along with the rhythm.
5. To stop the rhythm, press bl again.
E-28
LK240_e.book
29 ページ
2011年4月15日 金曜日 午前11時51分
Using Auto Accompaniment
5. Pressing bm again returns to rhythm only
Playing All Parts
Auto Accompaniment with Chords
Playing a chord with your left hand automatically adds bass
and harmony accompaniment parts to the currently selected
rhythm. It is just like having your own personal back up group
on call.
1. Start play of the Auto Accompaniment rhythm
part.
2. Press bm.
This enables chord input on the accompaniment
keyboard.
Accompaniment keyboard
• For information about starting Auto Accompaniment as
soon as a chord is played, see “Using Synchro Start” on
page E-32.
Selecting a Chord Input Mode
You can select from among the following five chord input
modes.
• FINGERED 1
• FINGERED 2
• FINGERED 3
• CASIO CHORD
• FULL RANGE CHORD
1. Hold down bm until the chord input mode
selection screen appears on the display.
Chord input mode
Lights
Cho r d
3. Use the accompaniment keyboard to play
chords.
This will cause bass and harmony Auto Accompaniment
parts to be added to the rhythm part.
Chords
(no melody played)
Melody
2. Use the bq (10-key) [–] and [+] keys to select
the chord input mode you want.
• If you do not perform any operation after the chord input
mode selection screen appears, the display will return
automatically to the screen that was displayed before
you held down
.
bm
F3
Example: Pressing D-F#-A-C on the accompaniment keyboard
4
Accompaniment for the D-F#-A-C chord (D7) sounds.
4. Play other chords with left hand as you play the
melody with your right hand.
E-29
English
accompaniment.
LK240_e.book
30 ページ
2011年4月15日 金曜日 午前11時51分
Using Auto Accompaniment
■ FINGERED 1, 2, and 3
With these three input modes, you play chords on the
accompaniment keyboard using their normal chord fingerings.
Some chord forms are abbreviated, and can be fingered with
one or two keys.
See page E-42 for information about chords that are
supported and how they are fingered on the keyboard.
Accompaniment keyboard
● FINGERED 1
Play the component notes of the chord on
the keyboard.
● FINGERED 2
Unlike FINGERED 1, 6th input is not
b
possible. m7 or m7 5 is input.
● FINGERED 3
Unlike FINGERED 1, allows input of
fraction chords with the lowest keyboard
note as the bass note.
CASIO CHORD Fingering
Chord Type
Example
Major Chords
Letters above the accompaniment
keyboard indicate the chord assigned
to each key. Pressing a single
accompaniment area key in the
CASIO CHORD mode will play the
major chord whose name is marked
above the key. All of the
accompaniment area keys that are
marked with the same chord name
play exactly the same chord.
C (C Major)
Minor Chords
To play a minor chord, press the
accompaniment area key that
corresponds to the major chord, while
also pressing one other
accompaniment area key to the right.
Cm (C Minor)
C C#D Eb E F F#G Ab A Bb B C C#DEb E F
C C#D Eb E F F#G Ab A Bb B C C#DEb E F
C7 (C Seventh)
Seventh Chords
To play a seventh chord, press the
accompaniment area key that
corresponds to the major chord, while
also pressing two other
accompaniment area keys to the right.
C C#D Eb E F F#G Ab A Bb B C C#DEb E F
Cm7
Minor Seventh Chords
To play a minor seventh chord, press (C Minor Seventh)
the accompaniment area key that
corresponds to the major chord, while
also pressing three other
accompaniment area keys to the right.
C C#D Eb E F F#G Ab A Bb B C C#DEb E F
■ CASIO CHORD
With CASIO CHORD, you can use
simplified fingerings to play the four types
of chords described below.
Accompaniment keyboard
• When playing a minor, seventh, or minor seventh chord, it
makes no different whether the additional keys you press
are black or white.
■ FULL RANGE CHORD
With this mode, you can use the full range
of the keyboard to play chords and the
melody.
See page E-42 for information about
chords that are supported.
Accompaniment keyboard / Melody keyboard
E-30
LK240_e.book
31 ページ
2011年4月15日 金曜日 午前11時51分
Using Auto Accompaniment
Auto Accompaniment Pattern Variations
Use the following procedures to play intro and ending
patterns, to play fill-in patterns, and to play variations of basic
Auto Accompaniment patterns.
■ Auto Accompaniment Variation
Each Auto Accompaniment pattern has a basic “normal
pattern” as well as a “variation pattern”.
1. Press 9.
■ Auto Accompaniment Fill-in
Use the procedure below to play a fill-in pattern during a
performance.
• A “fill-in” is a short phrase played where you want to change
the mood of a piece. A fill-in pattern can be used to create a
link between two melodies or an accent.
• Normal and variation patterns have their own unique fill-in
patterns.
● Normal Pattern Fill-in
1. While a normal pattern is playing, press 8.
This plays the fill-in for the normal pattern.
• Normal pattern play will resume after the fill in pattern is
complete.
Lights
This starts the variation pattern.
Lights
● Variation Pattern Fill-in
2. Pressing 8 returns to normal pattern.
Lights
1. While a variation pattern is playing, press 9.
This plays the fill-in for the variation pattern.
• Variation pattern play will resume after the fill in pattern
is complete.
Lights
■ Auto Accompaniment Intro
Use the following procedure to play an intro of a few
measures.
1. Press 7.
This starts the intro pattern. Normal pattern play will start
when the intro pattern is finished.
• If you press
while an intro pattern is being played,
the variation pattern will start when the intro pattern is
finished.
9
Lights
■ Auto Accompaniment Ending
Use the following procedure to play an ending of a few
measures.
1. While an Auto Accompaniment is playing, press
bk.
This will play the ending pattern and then stop Auto
Accompaniment play automatically.
Lights
E-31
English
Using Auto Accompaniment
Effectively
LK240_e.book
32 ページ
2011年4月15日 金曜日 午前11時51分
Using Auto Accompaniment
■ Using Synchro Start
Use the following procedure to configure the Digital Keyboard
to start Auto Accompaniment play as soon as you press a
keyboard key.
1. Press bk.
Adjusting the Accompaniment Volume
Use the following procedure to adjust the balance between
what you are playing on the keyboard and the volume of the
Auto Accompaniment.
1. Press 3 (FUNCTION) a number of times until
This enters accompaniment start standby.
“AcompVol” appears on the display (page E-4).
Flashes
A c ompVo l
2. Use the bq (10-key) [–] and [+] keys to adjust
the accompaniment volume.
2. Play a chord on the keyboard.
Using One-Touch Preset
This will start full part accompaniment (normal).
With One-Touch Preset, the Digital Keyboard automatically
configures optimal tone, tempo, and other settings in
accordance with the rhythm pattern you select.
Any of the following operations can be performed while in
synchro standby to start a non-normal pattern.
• To start with intro pattern, press
.
• To start with variation pattern play, press
.
7
9
1. Hold down bo (RHYTHM) until the current tone
screen appears on the display.
Changing Auto Accompaniment Speed
(Tempo)
Use the following procedure to change Auto Accompaniment
speed to a level that suits you.
2. Play a chord on the keyboard.
This will start accompaniment automatically.
1. Press 6.
Use w (slower) and q (faster) to change the tempo
setting. Holding down either button changes the setting at
high speed.
• Pressing w and q at the same time will initialize the
rhythm setting in accordance with the currently selected
rhythm.
• While the tempo value is flashing, you also can use
(10-key) to change it.
• If you do not perform any operation for after the tempo
setting screen appears, the display will return to the
screen displayed before you pressed
.
bq
6
Flashes
E-32
This will automatically apply the One-Touch Preset
settings in accordance with the rhythm pattern that is
currently selected.
LK240_03_e.fm
33 ページ
2011年4月18日 月曜日 午後4時22分
English
Connecting External Devices
bq
3
bm
Connecting a Computer
You can connect the Digital Keyboard to a computer and
exchange MIDI data between them. You can send play data
from the Digital Keyboard to music software running on your
computer, or you can send MIDI data from your computer to
the Digital Keyboard for playback.
Minimum Computer System Requirements
The following shows the minimum computer system
requirements for sending and receiving MIDI data. Check to
make sure that your computer complies with these
requirements before connecting the Digital Keyboard to it.
• Operating System
Windows® XP (SP2 or later) *1
Windows Vista® *2
Windows® 7 *3
Mac OS® X (10.3.9, 10.4.11, 10.5.8 or later, 10.6.6 or later)
*1: Windows XP Home Edition
Windows XP Professional (32-bit)
*2: Windows Vista (32-bit)
*3: Windows 7 (32-bit, 64-bit)
• USB port
• Never connect to a computer that does not conform to
the above requirements. Doing so can cause problems
with your computer.
Connecting the Digital Keyboard to Your
Computer
• Make sure you follow the steps of the procedure below
exactly. Connecting incorrectly can make data send
and receive impossible.
1. Turn off the Digital Keyboard and then start up
your computer.
• Do not start up the music software on your computer
yet!
2. After starting up your computer, use a
commercially available USB cable to connect it
to the Digital Keyboard.
B connector
USB cable
(A-B type)
Digital Keyboard USB port
A connector
Computer USB port
3. Turn on the Digital Keyboard.
• If this is the first time you are connecting the Digital
Keyboard to your computer, the driver software
required to send and receive data will be installed on
your computer automatically.
4. Start up your computer’s music software.
E-33
LK240_e.book
34 ページ
2011年4月15日 金曜日 午前11時51分
Connecting External Devices
5. Configure the music software settings to select
one of the following as the MIDI device.
CASIO USB-MIDI: (For Windows 7, Windows Vista,
Mac OS X)
USB Audio Device: (For Windows XP)
• For information about how to select the MIDI device,
see the user documentation that comes with the music
software you are using.
MIDI Settings
Keyboard Channel
A keyboard channel is the channel used for sending Digital
Keyboard data to a computer. You can select the channel you
want for sending Digital Keyboard data to a computer.
• The keyboard channel setting range is 01 to 16.
1. Press 3 (FUNCTION) a number of times until
• Be sure to turn on the Digital Keyboard first before
starting up your computer’s music software.
• USB send and receive is disabled during playback of a
Song Bank song (page E-16), or while the Digital
Keyboard is lighting during a power on alert operation.
Whenever you plan to exchange data between your
Digital Keyboard and computer, first turn off power on
alert (page E-6).
“Keybd Ch” appears on the display (page E-4).
Ke y bd Ch
2. Use the bq (10-key) [–] and [+] keys to change
• Once you are able to connect successfully, there is no
problem with leaving the USB cable connected when you
turn off your computer and/or Digital Keyboard.
• This Digital Keyboard conforms to General MIDI Level 1
(GM).
• For detailed specifications and connections that apply to
MIDI data send and receive by this Digital Keyboard, see
the latest support information provided by the website at the
following URL.
http://world.casio.com/
the keyboard channel.
Navigate Channels
The navigate channels can be used to display only the notes
of a particular channel (part) as on-screen guide information
from among the note information of a tune sent from the
computer.
■ Specifying the Navigate Channels
From among the 16 available channels (numbered 1 to 16),
you can specify any two neighboring channels (such as 05
and 06) as navigate channels. The smaller numbered channel
is the navigate (L) channel, while the larger numbered
channel is the navigate (R) channel. Specifying the navigate
(R) channel will automatically configure the navigate (L)
channel as well.
1. Press 3 (FUNCTION) a number of times until
“Navi. Ch” appears on the display (page E-4).
Na v i .
Ch
2. Use the bq (10-key) to specify the navigate (R)
channel.
This also will automatically configure the next lower
channel number as the navigate (L) channel.
E-34
LK240_e.book
35 ページ
2011年4月15日 金曜日 午前11時51分
Connecting External Devices
You can turn off the sound on one or both of the navigate
channels and play the cancelled part on the keyboard
yourself.
1. Press bm to select the channel setting you want
to turn off.
bm
Each press of
cycles through settings (1) through (4)
described below.
• If you turn off one channel, you can play the cancelled
part on the keyboard using the same tone as the
channel you turned off. If you turn off both channels
(option (3)), what you play on the keyboard sounds
using the tone of the navigate (R) channel.
Local Control
There are times when exchanging data with a computer when
you may not want the Digital Keyboard to sound notes you
play on its keyboard. The local control setting lets you do just
that.
1. Press 3 (FUNCTION) a number of times until
“Local” appears on the display (page E-4).
Loca l
2. Use the bq (10-key) [–] and [+] keys to specify
the local control setting.
Accomp Out
L
Enabling the Accomp Out setting causes Auto
Accompaniment data to be sent to the computer.
R
1. Press 3 (FUNCTION) a number of times until
Selected channel indicator appears.
“AcompOut” appears on the display (page E-4).
Navigate (L)
Channel
Navigate (R)
Channel
Sound
Onscreen
Guide
Sound
Onscreen
Guide
(1) R only displayed
{
×
×
{
(2) L only displayed
×
{
{
×
(3) LR displayed
×
{
×
{
(4) LR nor displayed
{
{
{
{
A c ompOu t
2. Use the bq (10-key) [–] and [+] keys to turn
Accomp Out on or off.
E-35
English
■ Turning Off the Navigate Channel Sound and
Playing the Part on the Keyboard
LK240_03_e.fm
36 ページ
2012年12月25日 火曜日 午後12時13分
Connecting External Devices
Connecting to Audio Equipment
This Digital Keyboard can be connected to commercially
available stereo, amplifier, or recording equipment, to a
portable audio player or other equipment.
Outputting Digital Keyboard Notes to Audio
Equipment
Connection requires commercially available connecting cords,
supplied by you. The connecting cords should have a stereo
standard plug on one end and a plug that matches the
configuration of the external device on the other end.
• Turn off the external device when making connections.
After connecting, turn down the Digital Keyboard and
external device volume levels whenever turning power
on or off.
• After connecting, turn on the Digital Keyboard and then
the external device.
• If Digital Keyboard notes sound distorted when they
are sounded from external audio equipment, lower the
Digital Keyboard’s volume setting.
Audio equipment, amplifier,
etc.
Stereo standard plug
Digital Keyboard PHONES/OUTPUT jack
Playing an External Device from the Digital
Keyboard (LK-240/LK-247 only)
Connection requires commercially available connecting cords,
supplied by you. The connecting cords should have a stereo
mini plug on one end and a plug that matches the
configuration of the external device on the other end.
• Turn off the Digital Keyboard when making
connections. After connecting, turn down the Digital
Keyboard and external device volume levels whenever
turning power on or off.
• After connecting, turn on the external device and then
the Digital Keyboard.
• If notes are distorted when they are sounded on the
external device, lower the volume setting of the
external device.
Portable audio player, etc.
Stereo mini plug
Digital Keyboard AUDIO IN jack
E-36
B
LK240_e.book
37 ページ
2011年4月15日 金曜日 午前11時51分
English
Reference
Troubleshooting
Symptom
Action
Included Accessories
I can’t find something that should be here.
Carefully check inside all of the packing materials.
Power Requirements
Power will not turned on.
• Check the AC adaptor or make sure that the batteries are facing
correctly (page E-5).
• Replace the batteries with new ones or switch over to AC adaptor
power (page E-5).
The Digital Keyboard outputs a loud sound and then
suddenly powers down.
Replace the batteries with new ones or switch over to AC adaptor
power (page E-5).
The Digital Keyboard suddenly powers down after a
few minutes.
This happens when Auto Power Off (page E-6) is triggered.
Display
If I don’t play anything for a few minutes, keyboard
keys suddenly start flashing. Things return to normal
after I press a keyboard key or a button.
Turn off the power on alert feature (page E-6).
The display keeps going out or are flashing.
Replace the batteries with new ones or switch over to AC adaptor
power (page E-5).
On-screen keyboard keys or notes remain on the
display.
A Step Up Lesson is in progress and the Digital Keyboard is waiting
for you to play the next note in the song. To stop this from happening,
cancel the lesson (page E-22).
Screen contents are visible only from straight ahead. This is dues to production limitations. It does not indicate malfunction.
Sound
Nothing happens when I press any keyboard key.
• Adjust the main volume setting (page E-6).
• Check if something is plugged into the PHONES/OUTPUT jack
( ) on the back of the Digital Keyboard.
• Turn power off and then back on to initialize all Digital Keyboard
settings (page E-6).
dp
bm
Nothing happens or notes do not play normally when
I play notes on the left side of the keyboard.
Press
to disable chord input in the accompaniment keyboard area
(page E-29).
Nothing happens when I start an Auto
Accompaniment.
• With rhythms 140, and 142 to 150, nothing will sound until you play
a chord on the keyboard. Try playing a chord (page E-29).
• Check and adjust the accompaniment volume setting (page E-32).
• Turn power off and then back on to initialize all Digital Keyboard
settings (page E-6).
Nothing happens when I start playback of a built-in
song.
• It takes a little time after you press the button until the song starts to
play. Wait for a moment for the song to start.
• Check and adjust the song volume (page E-18).
• Turn power off and then back on to initialize all Digital Keyboard
settings (page E-6).
The metronome does not sound.
• Check and adjust the accompaniment volume setting (page E-32).
• Check and adjust the song volume (page E-18).
• Turn power off and then back on to initialize all Digital Keyboard
settings (page E-6).
Notes keep sounding, without stopping.
• Turn power off and then back on to initialize all Digital Keyboard
settings (page E-6).
• Replace the batteries with new ones or switch over to AC adaptor
power (page E-5).
E-37
LK240_03_e.fm
38 ページ
2012年12月25日 火曜日 午後12時13分
Reference
Symptom
Action
Some notes are cut off while they are playing.
Notes are cut off whenever the number of notes being sounded
exceeds the maximum polyphony value of 48 (24 for some tones).
This does not indicate malfunction.
The volume or tone setting I made has changed.
• Adjust the main volume setting (page E-6).
• Turn power off and then back on to initialize all Digital Keyboard
settings (page E-6).
• Replace the batteries with new ones or switch over to AC adaptor
power (page E-5).
Output volume does not change even though is
change my keyboard touch (LK-240/LK-247 only).
• Change the Touch Response setting (page E-7).
• Turn power off and then back on to initialize all Digital Keyboard
settings (page E-6).
In certain keyboard ranges, the volume and tone
This is due to system limitations. It does not indicate malfunction.
quality sound are slightly different from those in other
keyboard ranges.
With some tones, octaves do not change at the far
ends of the keyboard.
This is due to system limitations. It does not indicate malfunction.
The pitch of the notes does not match other
accompanying instruments or sounds strange when
played long with other instruments.
• Check and adjust the transpose (page E-12) and tuning settings
(page E-12).
• Turn power off and then back on to initialize all Digital Keyboard
settings (page E-6).
The reverb of notes seems to change suddenly.
• Check and adjust the reverb setting (page E-11).
• Turn power off and then back on to initialize all Digital Keyboard
settings (page E-6).
Sounds I sampled were deleted.
Sampled data is deleted whenever Digital Keyboard power is turned
off (page E-14).
Operation
When I perform a skip forward or skip back
operation, the skip operation moves multiple song
measures instead of only a single measure.
While song playback is stopped or a Step Up Lesson is in progress,
skip forward and skip back operations are performed in phrase units
(page E-17).
Computer Connection
I can’t exchange data between the Digital Keyboard
and a computer.
E-38
• Check to make sure that the USB cable is connected to the Digital
Keyboard and computer, and that the device is selected correctly
with your computer’s music software settings (page E-33).
• Turn off the Digital Keyboard and then exit the music software on
your computer. Next, turn the Digital Keyboard back on and then
restart the music software on your computer.
B
LK240_03_e.fm
39 ページ
2012年12月25日 火曜日 午後12時13分
Reference
Model
LK-160/LK-165/LK-240/LK-247
Keyboard
61 standard-size keys
Touch Response
(LK-240/LK-247 only)
English
Specifications
2 types, Off
Key Light System
Up to 4 keys can be lit at the same time
Maximum Polyphony
48 notes (24 for certain tones)
Tones
Built-in Tones
400
Sampling Tones
1 (Full Sampling) or 3 (Short Sampling)
Sampling Time: 1 second (Full Sampling) or approximately 0.3 seconds each (Short Sampling)
Effects: 10 types (for Full Sampling samples)
Reverb
1 to 10, Off
Voice Pad
5 pads × 4 sets
(3 sets for sampled sounds, 1 set for percussion only)
Metronome
Beats per Measure
0, 2 to 6
Tempo Range
30 to 255
Song Bank
Tunes
110
Step Up Lesson
Lessons
4 (Listen, Watch, Remember, Auto)
Lesson Part
L, R, LR
Functions
Music Challenge
Repeat, Voice Fingering Guide, Note Guide, Performance Evaluation
20 notes
Auto Accompaniment
Rhythm Patterns
150
One Touch Presets
150
Other Functions
Transpose
±1 octaves (–12 to +12 semitones)
Tuning
A4 = 415.5 to 465.9 Hz (Initial Default: 440.0 Hz)
MIDI
16 multi-timbre received, GM Level 1 standard
Musical Information Function
Tone, Rhythm, Song Bank, numbers and names, staff notation, fingering, pedal operation,
tempo, measure and beat number, chord name, etc.
Inputs/Outputs
USB port
TYPE B
Sustain jack
Standard jack (sustain, sostenuto, soft, rhythm)
Phones/Output jack
Stereo standard jack
Output Impedance: 200 Ω, Output Voltage: 4.5 V (RMS) MAX
Audio In jack
(LK-240/LK-247 only)
Stereo mini jack
Input Impedance: 9 kΩ, Input Sensitivity: 200 mV
Mic In jack
Standard jack
Input Impedance: 3 kΩ, Input Sensitivity: 10 mV
Power Jack
9.5 V DC
Power Supply
2-way
Batteries
6 AA-size zinc-carbon batteries or alkaline batteries
Battery Life
Approximately 3 hours continuous operation on alkaline batteries
AC Adaptor
AD-E95100L
Auto Power Off
Approximately 6 minutes (during battery operation) or 30 minutes (during AC adaptor
operation) without any operation
Speakers
Output
Power Consumption
B
10 cm × 2
2W+2W
9.5 V = 7.7 W
E-39
LK240_03_e.fm
40 ページ
2012年12月25日 火曜日 午後12時13分
Reference
Dimensions
94.6 × 30.7 × 9.2 cm (37 1/4 × 12 1/16 × 3 5/8 inch)
Weight
LK-160/LK-165: Approximately 3.5kg (7.7 lbs) (without batteries)
LK-240/LK-247: Approximately 3.6kg (7.9 lbs) (without batteries)
• Design and specifications are subject to change without notice.
Operating Precautions
Be sure to read and observe the following operating precautions.
■ Location
Avoid the following locations for this product.
• Areas exposed to direct sunlight and high humidity
• Areas subjected to temperature extremes
• Near a radio, TV, video deck, or tuner
The above devices will not cause malfunction of the product, but interference from the product can cause audio or video
interference of a nearby device.
■ User Maintenance
• Never use benzine, alcohol, thinner, or other chemical agents to clean the product.
• To clean the product or its keyboard, wipe with a soft cloth moistened in a weak solution of water and a mild neutral detergent.
Wring all excess moisture from the cloth before wiping.
■ Included and Optional Accessories
Use only accessories that are specified for use with this product. Use of unauthorized accessories creates the risk of fire, electric
shock, and personal injury.
■ Weld Lines
Lines may be visible on the exterior of the product. These are “weld lines” that result from the plastic molding process. They are not
cracks or scratches.
■ Musical Instrument Etiquette
Always be aware of others around you whenever using this product. Be especially careful when playing late at night to keep the
volume at levels that do not disturb others. Other steps you can take when playing late at night are closing the window and using
headphones.
E-40
B
LK240_e.book
41 ページ
2011年4月15日 金曜日 午前11時51分
Reference
SONG BANK
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
WORLD
TWINKLE TWINKLE LITTLE STAR
LIGHTLY ROW
LONG LONG AGO
ON TOP OF OLD SMOKEY
SAKURA SAKURA
WHEN THE SAINTS GO MARCHING IN
AMAZING GRACE
AULD LANG SYNE
COME BIRDS
DID YOU EVER SEE A LASSIE?
MICHAEL ROW THE BOAT ASHORE
DANNY BOY
MY BONNIE
HOME SWEET HOME
AURA LEE
HOME ON THE RANGE
ALOHA OE
SANTA LUCIA
FURUSATO
GREENSLEEVES
JOSHUA FOUGHT THE BATTLE OF JERICHO
THE MUFFIN MAN
LONDON BRIDGE
UNDER THE SPREADING CHESTNUT TREE
SIPPIN’ CIDER THROUGH A STRAW
GRANDFATHER’S CLOCK
ANNIE LAURIE
BEAUTIFUL DREAMER
IF YOU’RE HAPPY AND YOU KNOW IT, CLAP YOUR
HANDS
MY DARLING CLEMENTINE
LITTLE BROWN JUG
HOUSE OF THE RISING SUN
SHE WORE A YELLOW RIBBON
YANKEE DOODLE
MY OLD KENTUCKY HOME
SZLA DZIEWECZKA
TROIKA
WALTZING MATILDA
ON THE BRIDGE OF AVIGNON
I’VE BEEN WORKING ON THE RAILROAD
OH! SUSANNA
CAMPTOWN RACES
JEANNIE WITH THE LIGHT BROWN HAIR
TURKEY IN THE STRAW
JAMAICA FAREWELL
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069
070
071
072
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091-100
101-110
EVENT
SILENT NIGHT
WE WISH YOU A MERRY CHRISTMAS
JINGLE BELLS
JOY TO THE WORLD
O CHRISTMAS TREE
PIANO/CLASSICS
MARY HAD A LITTLE LAMB
LE CYGNE FROM “LE CARNAVAL DES ANIMAUX”
JE TE VEUX
SONATA op.13 “PATÉTIQUE” 2nd Mov.
HEIDENRÖSLEIN
AIR FROM “SUITE no.3”
SPRING FROM “THE FOUR SEASONS”
HABANERA FROM “CARMEN”
BRINDISI FROM “LA TRAVIATA”
HUNGARIAN DANCES no.5
MINUET IN G MAJOR
MUSETTE IN D MAJOR
GAVOTTE (GOSSEC)
ARABESQUE (BURGMÜLLER)
CHOPSTICKS
DECK THE HALL
ODE TO JOY
AVE MARIA (GOUNOD)
SONATINA op.36 no.1 1st Mov.
PRELUDE op.28 no.7 (CHOPIN)
RÊVERIE
GYMNOPÉDIES no.1
GOING HOME FROM “FROM THE NEW WORLD”
FÜR ELISE
TURKISH MARCH (MOZART)
SONATA op.27 no.2 “MOONLIGHT” 1st Mov.
ETUDE op.10 no.3 “CHANSON DE L’ADIEU”
THE ENTERTAINER
WEDDING MARCH FROM “MIDSUMMER NIGHT’S
DREAM”
AMERICAN PATROL
FRÖHLICHER LANDMANN
LA CHEVALERESQUE
SONATA K.545 1st Mov.
LA PRIÈRE D’UNE VIERGE
VALSE op.64 no.1 “PETIT CHIEN”
LIEBESTRÄUME no.3
JESUS BLEIBET MEINE FREUDE
CANON (PACHELBEL)
SERENADE FROM “EINE KLEINE NACHTMUSIK”
MARCH FROM “THE NUTCRACKER”
EXERCISE
EXERCISE I
EXERCISE II
E-41
English
Song List
LK240_e.book
42 ページ
2011年4月15日 金曜日 午前11時51分
Reference
Fingering Guide
Fingered 1, Fingered 2 Chords
Fingered 3, Full Range Chords
In addition to the chords that can be fingered with Fingered 1
and Fingered 2, the following chords also are recognized.
C
#
C
C
Cm
Gm Am
C
C
D
C
E
C
F
C
b
Bm
C
G
C
Ddim
C
b
A
C
b
B
C
b
A7
C
B
C
F7
C
#
Cm
C
Fm7
C
Dm
C
Gm7
C
Fm
C
b
A add9
C
Cdim
Caug *3
Csus4 *3
Csus2 *3
C7
Cm7 *3
CM7
Cm7b 5 *3
C7b 5 *3
C7sus4
Cadd9
Cmadd9
CmM7
Cdim7 *3
C69 *3
C6 *1 *3
Cm6 *2 *3
*1 With Fingered 2, interpreted as Am7.
*2 With Fingered 2, interpreted as Am7b5.
*3 Inverted form not supported in some cases.
E-42
• With Fingered 3, the lowest note fingered is interpreted as
the base note. Inverted forms are not supported.
• With Full Range Chord, when the lowest note fingered is a
certain distance from the neighboring note, the chord is
interpreted as a fraction chord.
• Unlike Fingered 1, 2, and 3, Full Range Chord requires
pressing of at least three keys to form a chord.
Root
C#/(Db)
D
(D#)/Eb
E
F
F#/(Gb)
• Since the chord input range is limited, this model may not support some of the chords shown above.
m6
6
69
dim7
mM7
madd9
add9
7sus4
7b5
m7b5
M7
m7
7
sus2
sus4
aug
dim
C
G
(G#)/Ab
A
(A#)/Bb
English
B
43 ページ
m
M
Chord
Type
Chord Example List
LK240_e.book
2011年4月15日 金曜日 午前11時51分
Reference
E-43
B
7 8 9 bk bl bm
6
bq
br bs bt ck cl cm
bn bobp
45 ページ
1 2 3 4 5
LK-160/LK-165/LK-240/LK-247
LK240_04_es_MIDI.fm
2012年12月25日 火曜日 午後12時13分
Control
Change
Pitch Bender
After
Touch
Velocity
Key’s
Ch’s
B
64
66
0, 32
1
6, 38
7
10
11
Note OFF
Note ON
True voice
X
O
O
O (MSB only)
O
O *2
O
O
O
O
O
X
O
X
X
O
O
X
O *3
O *3
X 9nH v = 0, 8nH v =**
O 9nH v = 1 - 127
0 - 127
0 - 127 *1
X
X
O 9nH v = 100 (LK-160/165)
1-127 (LK-240/LK-247)
X 9nH v = 0
36 - 96
Mode 3
X
Mode 3
X
Default
Messages
Altered
Mode
Note
Number
1 - 16
1 - 16
1
1 - 16
Recognized
Default
Changed
Transmitted
Basic
Channel
Function
Hold 1
Sostenuto
Bank select
Modulation
Data entry
Volume
Pan
Expression
**: no relation
**: sin relación
Remarks
Version : 1.0
48 ページ
MIDI Implementation Chart
Model: LK-160/LK-165/LK-240/LK-247
LK240_04_es_MIDI.fm
2012年12月25日 火曜日 午後12時14分
LK240_es_Cover1-4.fm
2 ページ
2012年12月25日 火曜日 午後12時15分
B
O : Yes
X : No
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
Remarks
Aux
Messages
O
O
X
O
O
X
X
O
X
O
X
X
: All sound off
: Reset all controller
: Local ON/OFF
: All notes OFF
: Active Sense
: Reset
X
X
O
O
: Clock
: Commands
System
Real Time
X
X
X
X
X
X
: Song Pos
: Song Sel
: Tune
System
Common
O *2
O 0 - 127
O *2
O 0 - 127
Hold 1
Sostenuto
Soft pedal
Reverb send
RPN LSB, MSB
System Exclusive
After
Touch
Control
Change
Pitch Bender
Velocity
Note
Number
● Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your own, personal
use, any other use of the contents of this manual without the consent of CASIO is prohibited under copyright laws.
● IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION) ARISING OUT OF THE
USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
● The contents of this manual are subject to change without notice.
● The actual appearance of the product may be different from that shown in the illustrations in this User’s Guide.
● Company and product names used in this manual may be registered trademarks of others.
:True #
Key’s
Ch’s
Note OFF
Note ON
True voice
Default
Messages
Altered
Mode
Responsible within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
Program
Change
O
X
X
O
O
X
0, 32
1
6, 38
7
10
11
X
X
X
O 9nH v = 100 (LK-160/165)
1-127 (LK-240/LK-247)
X 9nH v = 0
36 - 96
Mode 3
X
1
1 - 16
Manufacturer:
CASIO COMPUTER CO.,LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Default
Changed
Function
This mark applies in EU countries only.
Basic
Channel
Model: LK-160/LK-165/LK-240/LK-247
Transmitted
• Before using the optional AD-E95100L Adaptor to power the unit, be sure to check the AC Adaptor for any damage first.
Carefully check the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC
adaptor that is seriously damaged.
• Never attempt to recharge batteries.
• Do not use rechargeable batteries.
• Never mix old batteries with new ones.
• Use recommended batteries or equivalent types.
• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated near the battery compartment.
• Replace batteries as soon as possible after any sign they are getting weak.
• Do not short-circuit the battery terminals.
• The product is not intended for children under 3 years.
• Use only CASIO AD-E95100L adaptor.
• The AC adaptor is not a toy.
• Be sure to disconnect the AC adaptor before cleaning the product.
O
O
O
O
O *2
O (MSB only)
O
O *2
O
O
O
O
X
O
X 9nH v = 0, 8nH v =**
Please note the following important information before using this product.
O 9nH v = 1 - 127
0 - 127
0 - 127 *1
Mode 3
X
1 - 16
1 - 16
Recognized
Important!
O *3
O *3
O *3
X
X
Bank select
Modulation
Data entry
Volume
Pan
Expression
Declaration of Conformity
Model Number: LK-160/LK-165/LK-240/LK-247
Trade Name: CASIO COMPUTER CO., LTD.
Responsible party: CASIO AMERICA, INC.
Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
64
66
67
91
100, 101
Remarks
Version : 1.0
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
*1: Depends on tone.
*1: Depende del tono.
*2: For details about NRPN, RPN, and system exclusive *2: Para obtener información acerca de NRPN, RPN y
messages, see MIDI Implementation at
los mensajes exclusivos del sistema, consulte
http://world.casio.com/.
Implementación MIDI en http://world.casio.com/.
*3: In accordance with pedal effect setting.
*3: De acuerdo con el ajuste de efecto de pedal.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
2012年12月25日 火曜日 午後12時15分
This recycle mark indicates that the packaging conforms to
the environmental protection legislation in Germany.
Esta marca de reciclaje indica que el empaquetado se
ajusta a la legislación de protección ambiental en Alemania.
LK-160
LK-165
LK-240
LK-247
USER’S GUIDE
Please keep all information for future reference.
Safety Precautions
Before trying to use the Digital Keyboard, be sure to
read the separate “Safety Precautions”.
GUÍA DEL USUARIO
Guarde toda información para tener como referencia futura.
Precauciones de seguridad
Antes de intentar usar el teclado digital, asegúrese de
leer las “Precauciones de seguridad” separadas.
K
MA1301-B Printed in China
LK240/165-ES-1B
ES
English
1 ページ
Español
LK240_es_Cover1-4.fm