D-Link DWS-3160-24PC Installation guide

Information in this document is subject to change without notice. Reproduction of this document in any manner whatsoever, without the written
permission of the D-Link Corporation, is strictly forbidden.
Trademarks used in this text: D-Link and the D-Link logo are trademarks of the D-Link Corporation; Microsoft and Windows are registered
trademarks of the Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either as the entities claiming the marks and the names or their
products. D-Link Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
© 2011 D-Link Corporation. All rights reserved.
November, 2011. P/N 651WS3160005G
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operating in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with this manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the
user may be required to take adequate measures.
Warnung!
Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen. In diesem Fall
kann vom Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.
Precaución!
Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio, en cuyo case, puede
requerirse al usuario para que adopte las medidas adecuadas.
Attention!
Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer des interférences
radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.
Attenzione!
Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può causare interferenze
radio, nel cui caso è possibile che l`utente debba assumere provvedimenti adeguati.
VCCI Warning
この装置は、クラス A 情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。
この場合には使用者が適切な対策を講ずるよう要求されることがあります。
VCCI-A
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Table of Contents
Intended Readers ......................................................................................................................................................... v
Typographical Conventions .......................................................................................................................................... v
Notes, Notices, and Cautions ....................................................................................................................................... v
Safety Instructions ....................................................................................................................................................... vi
Safety Cautions ....................................................................................................................................................... vi
General Precautions for Rack-Mountable Products .................................................................................................... vii
Protecting Against Electrostatic Discharge ................................................................................................................. viii
Chapter 1 Introduction ................................................................................................................................................ 1
Switch Description ........................................................................................................................................................ 1
Package Contents......................................................................................................................................................... 1
Features ........................................................................................................................................................................ 2
Ports .............................................................................................................................................................................. 3
Front Panel Components .............................................................................................................................................. 4
LED Indicators .............................................................................................................................................................. 4
Rear Panel Description ................................................................................................................................................. 5
Side Panel Description ................................................................................................................................................. 6
Chapter 2 Installation .................................................................................................................................................. 7
Installation Guidelines ................................................................................................................................................... 7
Installing the Switch without a Rack ......................................................................................................................... 7
Installing the Switch into a Rack ............................................................................................................................... 7
Installing SFP transceivers into the SFP Ports......................................................................................................... 8
Connecting to a Redundant Power Supply ................................................................................................................... 9
Redundant Power Supply, the DPS-200 .................................................................................................................. 9
Redundant Power Supply, the DPS-700 ................................................................................................................ 10
RPS Rack-Mountable Chassis, the DPS-800 ........................................................................................................ 12
RPS Rack-Mountable Chassis, the DPS-900 ........................................................................................................ 13
Chapter 3 Switch Connections ................................................................................................................................ 15
Switch to an End Node ............................................................................................................................................... 15
Switch to another Switch ............................................................................................................................................ 15
Switch to a Server ....................................................................................................................................................... 16
Switch to an Access Point directly .............................................................................................................................. 16
Chapter 4 Switch Management ................................................................................................................................ 17
Management Options ................................................................................................................................................. 17
Connecting to the Console Port .................................................................................................................................. 17
Connecting to the Switch for the first time .............................................................................................................. 19
Creating a User Account ........................................................................................................................................ 20
Configuring the IP Address..................................................................................................................................... 20
Connecting using SNMP ............................................................................................................................................. 22
Traps....................................................................................................................................................................... 23
Management Information Base (MIB) .................................................................................................................... 23
Connecting using the Web User Interface .................................................................................................................. 24
Logging onto the Web Manager ............................................................................................................................. 24
Areas of the User Interface..................................................................................................................................... 25
Chapter 5 D-Link Unified Access System ............................................................................................................... 26
D-Link Unified Access System Components .............................................................................................................. 26
D-Link Unified Switch ............................................................................................................................................. 26
D-Link Access Point ............................................................................................................................................... 26
WLAN Visualization ................................................................................................................................................ 27
D-Link Unified Access System Topology .................................................................................................................... 28
iii
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Single Unified Switch Deployment.......................................................................................................................... 28
Peer Unified Switch Deployment ............................................................................................................................ 28
Chapter 6 Appendix Section .................................................................................................................................... 30
Appendix A – Technical Specifications ....................................................................................................................... 30
General ................................................................................................................................................................... 30
Physical and Environmental ................................................................................................................................... 30
Performance ........................................................................................................................................................... 31
LED Indicators ........................................................................................................................................................ 31
Port Functions......................................................................................................................................................... 32
Wireless Functions ................................................................................................................................................. 33
Appendix B – Cables and Connectors ........................................................................................................................ 35
Ethernet Cable ........................................................................................................................................................ 35
Console Cable ........................................................................................................................................................ 36
Redundant Power Supply (RPS) Cable ................................................................................................................. 37
Appendix C – Module Specifications and Cable Lengths ........................................................................................... 39
Warranties & Support.................................................................................................................................................... 40
iv
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Intended Readers
Intended Readers
Typographical Conventions
Notes, Notices, and Cautions
Safety Instructions
General Precautions for Rack-Mountable Products
Protecting Against Electrostatic Discharge
The DWS-3160 Series Hardware Installation Guide contains detailed information about the hardware specifications
of a Switch in this series. It also contains brief information on how to configure and manage a Switch in this series.
This manual is intended for advanced level users that are familiar with network management concepts and
terminology. For all practical reasons all the Switches in this series will simply be referred to as the Switch throughout
this manual. All example screenshots are taken from the DWS-3160-24PC Switch.
Typographical Conventions
Convention
Description
[]
This convention is generally used in CLI commands. Square brackets indicate an
optional entry. For example: [copy | paste] means that optionally you can type copy or
you can type paste. Do not type the brackets.
Bold font
This font is generally used to put emphasis on a key subject in a sentence throughout
this manual. This font is also used to represent the physical CLI command used when
explaining a topic.
Boldface Typewriter
Font
This font is used to indicate CLI command examples used in this document.
Initial capital letter
The use of initial capital letters indicates that a referral to a specific name was made.
This will be seen a lot when referring to protocols, standards, keyboard keys, and
when we refer to the ‘Switch’ as a generic name for all switches with in the series. For
example: Click Enter.
Menu Name > Menu
Option
This convention indicates the referral to a menu structure found in the Web User
Interface of this Switch. For example: Device > Port > Port Properties means the
Port Properties menu option under the Port menu option that is located under the
Device menu.
Notes, Notices, and Cautions
A NOTE indicates that the reader must pay attention to this information in order to make better use of
the device.
A NOTICE indicates that the reader must observe the result when a certain action was taken.
A CAUTION indicates that the reader must pay serious attention to this information as negligence will
probably result in potential property damage, personal injury, or even death.
v
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Safety Instructions
Please pay careful attention to the following safety guidelines to ensure your own personal safety and to help protect
your system from potential damage.
Safety Cautions
To greatly reduce the risk of physical injury, electrical shock, fire, and damage to equipment, observe the following
precautions.
Observe and follow service markings.
•
Do not attempt to service any product, except when it is explained in the system’s documentation.
•
Opening or removing covers that are marked with this (
•
Only a trained service technician should service components inside these compartments.
) symbol may expose the user to electrical shock.
If any of the following conditions occur, unplug the product from the electrical outlet immediately and replace the part
or contact your trained service provider:
•
Damage to the power cable, extension cable, or plug.
•
An object has fallen into the product.
•
The product has been exposed to water.
•
The product has been dropped or damaged.
•
The product does not operate correctly when the operating instructions are correctly followed.
General safety cautions:
•
Keep the system away from radiators and heat sources. Also, do not block cooling vents.
•
Do not spill food or liquids on system components, and never operate the product in a wet environment. If the
system gets wet contact your trained service provider.
•
Do not push any objects into the openings of the system. Doing so can cause fire or electric shock by shorting
out interior components.
•
Only use this product with approved equipment.
•
Allow the product to cool before removing the cover or touching internal components.
•
Operate the product only from the type of external power source indicated on the electrical ratings label. If
unsure of the type of power source required, consult your service provider or local power company.
•
Be sure that attached devices are electrically rated to operate with the power available in your location.
•
Use only approved power cable(s). If you have not been provided with a power cable for your system or for
any AC-powered option intended for your system, purchase a power cable that is approved for use in your
country. The power cable must be rated for the product and for the voltage and current marked on the
product's electrical ratings label. The voltage and current rating of the cable should be greater than the ratings
marked on the product.
•
To help prevent electric shock, plug the system and peripheral power cables into properly grounded electrical
outlets. These cables are equipped with three-prong plugs to help ensure proper grounding. Do not use
adapter plugs or remove the grounding prong from a cable. If using an extension cable is necessary, use a 3wire cable with properly grounded plugs.
•
Observe the extension cable and power strip ratings. Make sure that the total ampere rating of all products
plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for the
extension cable or power strip.
•
To help protect the system from sudden, transient increases and decreases in electrical power, use a surge
suppressor, line conditioner, or uninterruptible power supply (UPS).
•
Position system cables and power cables carefully. Route cables so that they cannot be stepped on or tripped
over. Be sure that nothing rests on any cables.
vi
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
•
Do not modify power cables or plugs. Consult a licensed electrician or your power company for site
modifications. Always follow your local or national wiring rules.
When connecting or disconnecting power to and from hot-pluggable power supplies, observe the following guidelines:
•
Install the power supply before connecting the power cable to the power supply.
•
Unplug the power cable before removing the power supply.
•
If the system has multiple sources of power, disconnect power from the system by unplugging all power
cables from the power supplies.
•
Move products with care and ensure that all casters and stabilizers are firmly connected to the system. Avoid
sudden stops and uneven surfaces.
To help avoid damage to the system, be sure that the voltage selection switch, on the power supply, is set to match
the power available at the switch’s location:
•
115V/60Hz is used mostly in North and South America as well as Far Eastern countries like as South Korea
and Taiwan
•
100V/50Hz is used mostly in Eastern Japan and 100V/60Hz in Western Japan
•
230V/50Hz is used mostly in Europe, the Middle East, Africa and the Far East
General Precautions for Rack-Mountable Products
Please pay careful attention to the following precautions concerning rack stability and safety. Systems are considered
to be components in a rack. Thus, a component refers to any system, as well as to various peripherals or supporting
hardware.
CAUTION: Installing systems in a rack without the front and side stabilizers installed could cause the
rack to tip over, potentially resulting in serious injury. After installing system/components in a rack,
never pull more than one component out of the rack on its slide assemblies at one time. The weight of
more than one extended component could cause the rack to tip over and may result in serious injury.
•
Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and
that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
•
Always load the rack from the bottom up, and load the heaviest item in the rack first.
•
Make sure that the rack is level and stable before extending a component from the rack.
•
Use caution when pressing the component rail release latches and sliding a component into or out of a rack;
the slide rails can pinch your fingers.
•
After a component is inserted into the rack, carefully extend the rail into a locking position, and then slide the
component into the rack.
•
Do not overload the AC supply branch circuit that provides power to the rack. The total rack load should not
exceed 80 percent of the branch circuit rating.
•
Ensure that proper airflow is provided to components in the rack.
•
Do not step on or stand on any component when servicing other components in a rack.
CAUTION: Never defeat the ground conductor or operate the equipment in the absence of a suitably
installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if
uncertain that suitable grounding is available.
CAUTION: The system chassis must be positively grounded to the rack cabinet frame. Do not
attempt to connect power to the system until grounding cables are connected. Completed power and
safety ground wiring must be inspected by a qualified electrical inspector. An energy hazard will exist
if the safety ground cable is omitted or disconnected.
vii
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Protecting Against Electrostatic Discharge
Static electricity can harm delicate components inside the system. To prevent static damage, discharge static
electricity from your body before touching any of the electronic components, such as the microprocessor. This can be
done by periodically touching an unpainted metal surface on the chassis.
The following steps can also be taken prevent damage from electrostatic discharge (ESD):
1. When unpacking a static-sensitive component from its shipping carton, do not remove the component from
the antistatic packing material until ready to install the component in the system. Just before unwrapping the
antistatic packaging, be sure to discharge static electricity from your body.
2. When transporting a sensitive component, first place it in an antistatic container or packaging.
3. Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads, workbench pads
and an antistatic grounding strap.
viii
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Chapter 1
Introduction
Switch Description
Package Contents
Features
Ports
Front Panel Components
LED Indicators
Rear Panel Description
Side Panel Description
Switch Description
The DWS-3160 Series Gigabit Ethernet Unified Switch is specifically tailored for a small and remote office
environment and fulfills the growing demand of wireless unified switches in this segment. This series provides a
performance optimized, cost effective solution for small and remote offices as well as small to medium sized
enterprise wireless network deployments.
With the default D-Link License Management Service (DLMS) agreement, this Switch can manage up to 12 unified
Access Points. After an optional upgrade of the license agreement, purchased from D-Link, this Switch can manage
up to 48 unified Access Points per unified Switch. The most powerful feature of this Switch is that up to 4 Switches
can form a cluster to manage up to 192 unified Access Points centrally with a single IP address.
This cost effective Gigabit Switch provides an affordable solution for Administrators to upgrade their networks to high
speed Gigabit connections. The advanced Access Control Lists (ACLs) and User Authentication functions on the
Switch extends network security coverage from the Core part of the network to the Edge parts. A unique D-Link
Safeguard Engine protects this Switch from outside networking threats and thereby increasing overall reliability,
serviceability, and availability.
The Switch is equipped with Copper ports (10/100/1000Mbps) and SFP ports (10/1000Mbps) that can be used to
attach various networking devices to the network like Computers, Notebooks, Print Servers, Network Attached
Storage devices, IP Cameras, VoIP PBX devices, and other Switches. The Small Form Factor Portable (SFP) combo
ports can be used together with fiber-optical transceivers in order to connect various other networking devices, using a
fiber-optic connection, to the network at Gigabit Ethernet speeds over great distances.
All the copper ports the DWS-3160-24PC Switch also offers Power over Ethernet (PoE) for a variety of uses. On the
DWS-3160-24PC Switch, each Gigabit port supports the standards IEEE 802.3af and IEEE 802.3at Power over
Ethernet that allows PoE devices like Access Points (supporting the standard IEEE 802.11n), VoIP phones and IP
Cameras to connect to the Switch and receive power from it at the same time. This provides ease of installation and
placement, as well as lesser power points needed for the devices connected to the Switch.
Package Contents
Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following
items:
•
•
•
•
•
•
•
One DWS-3160 Series Switch.
One Quick Installation Guide.
One AC power cord.
One RJ-45 to RS-232 console cable.
One rack mounting kit (two brackets and screws).
Four rubber feet with adhesive backing.
One CD containing the Web UI Reference Guide, CLI Reference Guide, and D-View module.
If any item is missing or damaged, please contact your local D-Link reseller for replacement.
1
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Features
This Switch series is action packed with an abundance of networking features that span inside and outside of the
traditional Layer 2 framework making it truly a Layer 2+ Switch. The list below highlights the significant protocols and
features supported by this Switch.
Local Area Networking (LAN) features that can be found on this Switch series are:
•
Virtual Stacking otherwise known as Clustering.
•
A 16K MAC Address Table.
•
Flow Control with Head-Of-Line blocking prevention.
•
Jumbo Frame of up to 13Kb.
•
Internet Group Management Protocol (IGMP)
Snooping Versions 1, 2, and 3.
•
Internet Group Management Protocol (IGMP)
Authentication.
•
Multicast Listener Discovery (MLD) Snooping Version
1 and 2.
•
Spanning Tree Protocols like 802.1D STP, 802.1w
RSTP, and 802.1s MSTP.
•
BPDU Attack Protection.
•
D-Link Loopback Detection Version 4.0.3
•
Link Aggregation (IEEE 802.3ad).
•
Port Mirroring that includes RSPAN.
•
Link Layer Discovery Protocol (LLDP).
•
Network Load Balancing (NLB).
•
Layer 2 Protocol Tunneling (L2PT).
•
PPPoE Circuit-ID Tag Insertion.
•
Virtual LAN (VLAN) using the IEEE 802.1Q protocol.
•
VLAN Grouping.
•
Voice VLAN and Guest VLAN.
•
Port-based, MAC-based, and Protocol-based VLAN.
•
Asymmetric VLAN and ISM VLAN.
•
VLAN Trunking and Private VLAN.
•
Static Routing.
•
Virtual Router Redundancy Protocol (VRRP).
•
Quality Of Service (QoS)
•
Queue Handling (Strict and Weighted Round Robin).
•
Class of Service (CoS).
•
Bandwidth Control.
•
Layer 3, Control Packet Filtering.
•
Access Control Lists (ACLs), Ingress and Egress
ACLs.
•
CPU Interface Filtering (Software ACL).
•
Secure Shell (SSH).
•
Secure Sockets Layer (SSL).
•
Port Security.
•
Storm Control (Unicast/Broadcast/Multicast).
•
Traffic Segmentation
•
D-Link Safeguard Engine.
•
DHCP Server Screening.
•
ARP Spoofing Prevention.
•
Filter Database (FDB) Security.
•
NetBIOS/NetBEUI Filtering.
•
DoS Prevention.
•
Proxy ARP.
•
Access Authentication Control.
•
IEEE 802.1X Network Access Control.
•
Captive Portal.
•
MAC-based Access Control (MAC).
•
Compound Authentication.
•
Microsoft Network Access Protection (NAP).
•
RADIUS Accounting and Authentication.
•
User Account Privileges.
•
Trusted Hosts.
•
Authentication Database Failover Enhancement.
•
Command Logging.
•
Web-based GUI Management.
•
Command Line Interface (CLI) Management.
•
Telnet Server/Client and TFTP Client.
•
Simple Network Management Protocol (SNMP).
•
SNMP Traps.
•
Trap/Alarm/Log Severity Control.
•
RMON Version 1 and 2.
•
sFLOW.
•
DHCP Auto-configuration, Client and Relay.
•
Multiple Image and Configuration support.
•
CPU Monitoring.
•
Password Encryption and Recovery.
•
IPv6 Neighbor Discovery (ND).
•
Internet Control Message Protocol (ICMP).
•
Simple Mail Transfer Protocol (SMTP).
•
SD Card Management.
•
Cable Diagnostics.
•
Ethernet Link OAM (IEEE 802.3ah).
•
Power Saving.
•
Time-based Power-over-Ethernet (PoE).
•
Wi-Fi Multimedia Power Save (WMM-PS).
•
Intelligent Green Network (D-Link Green 3.0).
•
D-Link License Management System (DLMS).
•
TACACS+ Authentication
®
2
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
•
Management Information Base (MIBs) for MIBII, Bridge MIB, SNMPv2 MIB, RMON MIB, RMONv2 MIB, Ether-like
MIB, 802.1p MIB, IF MIB, RADIUS Authentication Client MIB, RADIUS Accounting Client MIB, Ping and
Traceroute MIB, Private MIB, IPv6 MIB, IP MIB, TCP MIB, Zone Defense MIB, UDP, ICMP, ARP, Entity MIB, and
TCP/IP-based Internet.
Wireless Local Area Networking (WLAN) features that can be found on this Switch series are:
•
Switch and Access Point Discovery.
•
Fast Roaming.
•
Intra-Switch Roaming
•
Inter-Switch Roaming
•
Layer 2 and Layer 3 Roaming.
•
Tunnel Protocols like D-Link Wireless AP Protocol
(DWAPP) and CAPWAP-like protocol.
•
MSS Reduction.
•
Tunnel (L3 Tunneling) and non-Tunnel (VLAN
Forwarding) modes.
•
AP to AP Tunneling.
•
Multiple ESSIDs per Access Point.
•
Multiple SSIDs per Switch.
•
Automatic AP RF channel adjustment.
•
Automatic AP transmit output power adjustment.
•
RF Self-healing around Failed AP.
•
Load Balancing.
•
AP Software version Auto-detection and Central
Firmware dispatch.
•
AP Auto-discovery.
•
Remote AP rebooting.
•
AP, Client and Ad-hoc Client monitoring.
•
AP Authentication.
•
Centralized RF/Security policy management.
•
Visualized AP Management Tool.
•
Unified AP Support (DWL-8600AP, DWL-3600AP
and DWL-6600AP).
•
Wireless Multimedia (WMM).
•
SVP (Spectralink Voice Protocol).
•
Wireless Standards like IEEE 802.11a, 802.11b,
802.11g, 802.11d, 802.11h, 802.11n.
•
Wireless Security Modes like WEP, WPA, and WPA2.
•
IEEE 802.1X EAP types like EAP-MD5, EAP-TLS,
EAP-TTLS, EAP-FAST, EAP-SIM, PEAP-GTC,
PEAP-TLS, and PEAP-MS-CHAPv2.
•
Wireless Intrusion Detection System (WIDS).
•
Rogue AP Detection.
•
Rogue AP Mitigation.
•
Captive Portal.
•
Station Isolation.
Ports
In the DWS-3160 Series there are 2 Switches. They are:
•
The DWS-3160-24TC that includes 20 Copper ports (10/100/1000BASE-T) and 4 Combo Copper/SFP ports
(1000BASE-T/SFP), Layer 2+, Unified Switch.
•
The DWS-3160-24PC that includes 20 Copper PoE ports (10/100/1000BASE-T) and 4 Combo Copper/SFP
PoE ports (1000BASE-T/SFP), Layer 2+, Unified Switch.
All the Switches, in the Series, are equipped with:
•
One RJ-45 Console port (used to connect to the Command Line Interface (CLI) of the Switch). This port uses a
special console cable (included with the packing) with a DB9 interface to connect the Switch to a PC.
•
One Redundant Power Supply (RPS) outlet for optional external RPS.
NOTE: For customers interested in D-View, D-Link Corporation's proprietary SNMP management software, go to http://dview.dlink.com.tw/ and download the software and manual.
3
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Front Panel Components
The Front panel of the Switch consists of a Console port, LED indicators, Copper (10/100/1000Mbps) ports, SFP
(10/1000Mbps) ports and an SD Card slot.
Figure 1- 1. Front panel view of the DWS-3160-24TC
Figure 1- 2. Front panel view of the DWS-3160-24PC
A separate table below describes LED indicators in more detail.
LED Indicators
On the Switch’s front panel we’ll find the following LED indicators: Power, Console, RPS, Fan, and SD. For each
Copper/SFP port, also found on the front panel, there is a Link/Act light. The DWS-3160-24PC Switch is also
equipped with an additional PoE light, to indicate whether the ports are running in the Power-over-Ethernet mode or
not.
Figure 1- 3. LED indicators for the DWS-3160-24TC
Figure 1- 4. LED indicators for the DWS-3160-24PC
4
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
LED
Description
Power
This LED will light solid green after the Switch has been powered on successfully.
This LED will be off when the Switch is no longer receiving power (i.e. powered off).
Console
This LED will blink green during the Power-On Self Test (POST).
This LED will light solid green when a user is logged in through the console port.
This LED will be off after the POST finished successfully and no user is connected to the
console port.
RPS
This LED will light solid green if the Redundant Powers Supply is in use.
This LED will blink green when the Switch detects that the RPS is connected.
This LED will be off when the RPS is not in use.
Fan
This LED will blink red when a fan fails.
This LED will be off when all the fans are working properly.
SD
This LED will light solid green if a Secure Digital (SD) card is plugged in.
This LED will blink green when the Switch is reading or writing data to and from the SD
card.
This LED will be off when no SD card is plugged into the SD port.
This LED will light solid red when an SD card failure has been detected.
Link/Act LEDs
This LED will light solid green when there is a secure connection to a 1000Mbps
Ethernet device at any of the ports.
This LED will light solid orange when there is a secure connection to a 10/100Mbps
Ethernet device at any of the ports.
This LED will blink green when a 1000Mbps port is active, or blink orange when a
10/100Mbps port is active.
This LED will be off when there is no link or activity.
PoE LED Mode
(DWS-3160-24PC Only)
This LED will light solid green when the port is feeding power to the PoE devices
plugged in.
This LED will light solid orange when the port is in an error condition state.
This LED will be off when the port is not supplying power to the device plugged in.
After the pressing the ‘Mode’ button, only the port LEDs, that feed power, will be lit.
Rear Panel Description
The Rear panel of the Switch consists of a power connector and an outlet for an external redundant power supply.
Figure 1- 5. Rear panel view of the DWS-3160-24TC
Figure 1- 6. Rear panel view of the DWS-3160-24PC
Connect the one end of the power cord supplied to the power connector and the other end into a properly grounded
electrical outlet. The Switch will automatically adjust the power setting to adapt to any voltage supply in the range from
5
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
100~240VAC at 50~60Hz.
In addition, an optional external Redundant Power Supply (DPS-200 for the DWS-3124-24TC and DPS-700 for the
DWS-3124-24PC) can be plugged into the connector displayed above. When the internal power fails, this optional
external RPS will take over all the power immediately and automatically.
In the event that a power failure might occur in the environment and no UPS is used, as a precaution, unplug the
power cord from the Switch. After the return of power, you can plug the power cord back into the Switch’s power
connector.
Side Panel Description
The Side panel of the Switch consists out of heat and fan vents that are used to dissipate heat. Do not block these
openings. Leave at least 4 inches of space at the rear and sides of the Switch for proper ventilation. Be reminded that
without proper heat dissipation and air circulation, system components might overheat, which could lead to system
failure or even severely damage components.
Figure 1- 7. Side panels of the DWS-3160-24TC
Figure 1- 8. Side panels of the DWS-3160-24PC
6
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Chapter 2
Installation
Installation Guidelines
Connecting to a Redundant Power Supply
Installation Guidelines
This section will discuss the hardware installation guidelines that the user must follow in order to properly and safely
install this Switch into the appropriate environment.
•
Visually inspect the power cord and see that it is fully secured to both the power connector, on the Switch, and
the electrical outlet, that supplies power.
•
Install the Switch in a fairly cool and dry place within the acceptable temperature and humidity operating
ranges.
•
Install the Switch in a site free from strong electromagnetic field generators such as motors, vibration, dust,
and direct exposure to sunlight.
Installing the Switch without a Rack
This section is used to guide the user through installing the Switch in an area other than a switch rack. Attach the
rubber feet included to the bottom of the Switch. Take note that there should be marked blocks on the bottom of the
Switch to indicate where to attach the rubber feet. These marking are usually found at each bottom corner of the
device. The rubber feet cushion the Switch, protecting the casing from scratches and preventing it from scratching
other surfaces.
Figure 2- 1. Prepare the Switch for installation on a desktop or shelf
Install the Switch on a sturdy, level surface that can support the weight of the Switch (see the Appendix section for the
weight specifications of each Switch). Do not place any heavy objects on the Switch. The power outlet should be
within 1.82 meters (6 feet) of the Switch.
Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. Leave at least 10 cm
(4 inches) of space at the front and rear of the Switch for ventilation.
Installing the Switch into a Rack
This section is used to guide the user through installing the Switch into a switch rack. The Switch can be mounted in a
standard 19"(1U) rack using the provided mounting brackets. Use the following diagram as a guide.
7
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Figure 2- 2. Fasten mounting brackets on the Switch
Fasten the mounting brackets supplied to the sides of the Switch using the screws provided. With the brackets
attached securely, the Switch can be mounted in a standard rack, as shown below.
Figure 2- 3. Installing the Switch in a rack
Make sure that there is adequate space around the Switch to allow for proper air flow, ventilation, and cooling.
Installing SFP transceivers into the SFP Ports
The Switch is equipped with small form-factor pluggable (SFP) ports (otherwise known as Mini-GBIC ports) that can
be used to connect various other networking devices to this Switch that do not support the standard copper wiring
connection. These ports are generally used to connect this Switch to networking devices that can only be accessed
via an optical fiber connection and is normally used for a connection that spans greater distances. The maximum
distance that the copper wiring connection can reach is 100 meters. Fiber optic connections can span over several
kilometers.
The figure below illustrates how to properly insert SFP transceivers into the Switch’s SFP ports.
8
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Figure 2- 4. Inserting SFP transceivers into the Switch’s SFP ports
A complete list of SFP transceivers, compatible with this Switch, can be found in the Appendix section, at the end of
this document.
Connecting to a Redundant Power Supply
This Switch can be connected to the Redundant Power Supply (RPS) using either a 14-pin DC power cable or a 22pin DC power cable. A standard, three-pronged AC power cable connects to the redundant power supply and the
main power source to provide power to the RPS. The external redundant power supply is only used when the internal
power supply fails. After the internal power supply fails, the external RPS will immediately take over the power
supplying duties to the Switch automatically.
Please note that every Switch within this series will make use of a specific RPS.
The DWS-3160-24TC must be used together with the DPS-200 Redundant Power Supply or an equivalent RPS.
The DWS-3160-24PC must be used together with the DPS-700 Redundant Power Supply or an equivalent RPS.
Redundant Power Supply, the DPS-200
The D-Link, DPS-200, External Redundant Power Supply, provides a backup power solution to the DWS-3160-24TC
Switch in the event that the Internal Power Supply fails. The DPS-200 is a standalone, low-cost, simple solution that
can prevent the Switch from shutting down when the Internal Power Supply fails. This option is imperative when the
availability of this Switch on the network is of high importance.
9
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Figure 2- 5. Connecting the DWS-3160-24TC to the DPS-200
To connect the DPS-200 to the Switch for the first time, follow these steps:
1. Disconnect the power cable from the power connector of the Switch.
2. Interlink the RPS ports of the Switch and the DPS-200 by using the 14-pin DC power cable, supplied with the
RPS.
3. Interlink the Power connector, of the DPS-200, and the grounded electrical outlet by using a standard AC
power cable. A green LED on the front of the DPS-200 will illuminate to indicate a successful connection.
4. Reconnect the power cable to the power connector of the Switch.
5. No software configuration is needed for this installation.
CAUTION: Do NOT use the DWS-3160-24TC Switch with any Redundant Power System other
than the DPS-200.
Redundant Power Supply, the DPS-700
The D-Link, DPS-700, External Redundant Power Supply, provides a backup power solution to the DWS-3160-24PC
Switch in the event that the Internal Power Supply fails. The DPS-700 is a standalone, low-cost, simple solution that
can prevent the Switch from shutting down when the Internal Power Supply fails. This option is imperative when the
availability of this Switch on the network is of high importance.
10
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Figure 2- 6. Connecting the DWS-3160-24PC to the DPS-700
To connect the DPS-700 to the Switch for the first time, follow these steps:
1. Disconnect the power cable from the power connector of the Switch.
2. Interlink the RPS ports of the Switch and the DPS-700 by using the 22-pin DC power cable, supplied with the
RPS.
3. Interlink the Power connector, of the DPS-700, and the grounded electrical outlet by using a standard AC
power cable. A green LED on the front of the DPS-700 will illuminate to indicate a successful connection.
4. Reconnect the power cable to the power connector of the Switch.
5. No software configuration is needed for this installation.
CAUTION: Do NOT use the DWS-3160-24PC Switch with any Redundant Power System other
than the DPS-700.
11
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Figure 2- 7. Front view of the DPS-700
RPS Rack-Mountable Chassis, the DPS-800
Because of the small size of the DPS-200, the DPS-800 can be used to house and mount the DPS-200 into a switch
rack. The DPS-800 is a standard-size rack mount (1U) designed to hold up to two DPS-200 redundant power
supplies. Using this rack mount chassis, will allow the user to save space when deploying the DPS-200 RPS’s into a
switch rack.
Figure 2- 8. Installing the DPS-200 in the DPS-800
The RPS can be mounted in a standard 19" rack. Use the following diagram to guide you.
12
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Figure 2- 9. Installing the DPS-800 in an Equipment Rack
NOTE: The DPS-800 is NOT equipped with any power supplies on its own. This is a 2-slot, rackmountable chassis.
RPS Rack-Mountable Chassis, the DPS-900
Because of the small size of the DPS-200, the DPS-900 can be used to house and mount the DPS-200 into a switch
rack. The DPS-900 is a standard-size rack mount (5U) designed to hold up to eight DPS-200 redundant power
supplies. Using this rack mount chassis, will allow the user to save space when deploying the DPS-200 RPS’s into a
switch rack.
Figure 2- 10. Inserting the DPS-200 into the DPS-900
13
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
The RPS can be mounted in a standard 19" rack. Use the following diagram to guide you.
Figure 2- 11. Installing the DPS-900 into the equipment rack
NOTE: The DPS-900 is NOT equipped with any power supplies on its own. This is an 8-slot, rackmountable chassis.
14
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Chapter 3
Switch Connections
Switch to an End Node
Switch to another Switch
Switch to a Server
Switch to an Access Point directly
Switch to an End Node
End node is a generic name for edge networking devices that will be connected to this Switch. Typical examples of
end nodes are Personal Computers (PCs), Notebooks, Access Points, Print Servers, VoIP Phones and more. Each
end node will be outfitted with a 10/100/1000Mbps, RJ-45, networking port. Normally end nodes will connect to this
Switch by using a standard twisted-pair, UTP/STP, network cable. Any one of the networking ports, found on this
Switch, can be used to connect to an end node. After a successful connection, the corresponding Link/Act light will
illuminate and blink to indicate that packet activity is taking place on that port.
The diagram below display a typical end node connected to the Switch.
Figure 3- 1. Connecting the Switch to an end node
Switch to another Switch
Another popular configuration is to connect this Switch to another Switch or Hub. This network typography is
considered when one Switch does not have enough ports to cater for all the end nodes in the network. There is a
great deal of flexibility in the type of cabling that can be used to interlink switches. The copper ports support cables
like Categories 3, 4, 5, and 5e running on standards like 10BASE-T, 100BASE-TX, and 1000BASE-T. Two or more
Switches can also be interlinked using fiber-optic cables via the Switch’s SFP ports.
Figure 3- 2. Connecting a Switch to another switch
15
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Switch to a Server
When configuring a network, users will most likely have to add a Server or two to this Switch. Generally, any port on
this Switch can be used to connect to a Server, as they all operate at a maximum speed of one Gigabit per second.
What sets this Switch apart is the fact that there are powerful software applications available on this Switch that
specifically caters for better Server access, management and security.
Figure 3- 3. Connecting the Switch to a server
Switch to an Access Point directly
This Switch can be used to connect to Wireless Access Points (like the DWL-8600AP, DWL-3600AP, and DWL6600AP) to manage, configure and monitor them. An Access Point can either be configured as a Standalone or a
Managed Access Point. For the Unified System to function at optimal performance and flexibility, it is more feasible to
configure the Access Point to function as a Managed Access Point. This means that the Switch will manage the
Access Point.
16
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Chapter 4
Switch Management
Management Options
Connecting to the Console Port
Connecting using SNMP
Connecting using the Web User Interface
Management Options
This Switch series provides multiple access platforms that can be used to configure, manage and monitor networking
features available on this Switch. Currently there are three management platforms available and they are described
below.
The Command Line Interface (CLI) through the Serial Port or remote Telnet
This Switch can be managed, out-of-band, by using the console port on the front panel of the Switch. Alternatively, the
Switch can also be managed, in-band, by using a Telnet connection to any of the Copper/SFP ports in this Switch.
The command line interface provides complete access to all Switch management features.
SNMP-based Management
The Switch can be managed with an SNMP-compatible console program. The Switch supports SNMP version 1.0,
version 2.0 and version 3.0. The SNMP agent decodes the incoming SNMP messages and responds to requests with
MIB objects stored in the database. The SNMP agent updates the MIB objects to generate statistics and counters.
Web-based Management Interface
After successfully installing the Switch, the user can configure the Switch, monitor the LED panel, and display
statistics graphically using a Web browser, such as Microsoft® Internet Explorer (version 5.5 and later), Mozilla Firefox
(version 2.0 and later), Safari (version 4.0 and later), and Google Chrome (version 6.0 and later).
Connecting to the Console Port
The front panel of the Switch provides a port that enables a connection to a computer monitoring and configuring the
Switch. The console port is an RJ-45 port and requires a special cable that is included with the Switch, to establish the
physical connection.
To use the console port, the following equipment is needed:
•
A terminal or a computer with both an RS-232 serial port and the ability to emulate a terminal.
•
A console cable with a male DB-9 connector on one end and an RJ-45 connection on the other. This cable
should be included with the Switch. It establishes the physical connection to the console port.
Using a terminal to connect to the console port:
Connect the male DB-9 connector on the console cable (shipped with the Switch) to the RS-232 serial port on the
computer running terminal emulation software then insert the RJ-45 connector into the RJ-45 console port on the front
of the Switch.
17
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Set the terminal emulation software as follows:
•
Select the appropriate serial port (COM1 or
COM2).
•
Set the data rate to 115200 baud.
•
Set the data format to 8 data bits, 1 stop bit, and
no parity.
•
Set flow control to none.
Figure 4- 1. COM1 Properties
•
Under Properties, select VT100 for Emulation
mode.
•
Select Terminal keys for Function, Arrow and Ctrl
keys. Make sure to use Terminal keys (not
Windows keys) are selected.
NOTE: When using HyperTerminal with the
Microsoft® Windows® 2000 operating
system, ensure that Windows 2000 Service
Pack 2 or later is installed. Windows 2000
Service Pack 2 allows use of arrow keys in
HyperTerminal's VT100 emulation. See
www.microsoft.com for information on
Windows 2000 service packs.
Figure 4- 2. Connection Properties
After correctly configuring the terminal, plug the power cable into the power receptacle on the back of the Switch. The
boot sequence will appear in the terminal.
18
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Boot Procedure
V1.00.001
------------------------------------------------------------------------------Power On Self Test ........................................
MAC Address
H/W Version
100 %
: 00-11-22-33-45-67
: A1
Please Wait, Loading V1.00.037 Runtime Image ..............
UART init .................................................
Starting runtime image
Device Discovery ..........................................
Configuration init ........................................
100 %
100 %
100 %
100 %
Figure 4- 3. Boot up display in console screen
After the boot sequence has been completed, the console login screen will be displayed.
Connecting to the Switch for the first time
The Switch supports user-based security that can allow prevention of unauthorized users from accessing the Switch
or changing its settings. This section will explain how to log into the Switch’s Command Line Interface via the out-ofband console connection.
Upon initial connection to the Switch, the login screen appears (see example below).
DWS-3160-24PC Gigabit Ethernet Switch
Command Line Interface
Firmware: Build 1.00.037
Copyright(C) 2011 D-Link Corporation. All rights reserved.
UserName:
PassWord:
DWS-3160-24PC:admin#
Figure 4- 4. The Switch’s Login Screen
By default, there is no Username and Password configured in the account settings of this Switch. This will allow the
user to simply connect to this Switch for the first time by pressing the ‘Enter’ key twice.
After press Enter for both the Username and Password fields, access will be given to enter commands after the
command prompt (DWS-3160-24PC:admin#) appears.
NOTE: The first user automatically gets Administrator level privileges. At least one Admin-level user
account must be created for the Switch.
19
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Creating a User Account
As you will have noticed by now is that this Switch does not have a default username and password. One of the first
and most important tasks will be to create user accounts. Logging in using a predefined administrator-level username
will give the user privileged access to the Switch's management software. Also this will prevent unauthorized access
to the Switch, and record the passwords for future reference.
An example to create an administrator-level account for the Switch called ‘NewUser’:
DWS-3160-24PC:admin#create account admin NewUser
Command: create account admin NewUser
Enter a case-sensitive new password:******
Enter the new password again for confirmation:******
Success.
DWS-3160-24PC:admin#
Figure 4- 5. To create a user account
1. At the CLI command prompt, enter the ‘create account admin NewUser’ command and press ‘Enter’. This
will create a new administrator-level account called ‘NewUser’.
2. The Switch will then prompt the user to enter a password. Enter the password for the administrator account
and press the ‘Enter’ key.
3. The Switch will again prompt the user to enter the same password again to verify it. Enter the same password
and press the ‘Enter’ key.
4. A “Success” response message will be displayed, by the Switch, to verify the successful creation of the new
administrator-level account.
NOTE: Passwords are case sensitive. User names and passwords can be up to 15 characters in
length.
Configuring the IP Address
Each Switch must be assigned its own IP Address, which is used for communication with an SNMP network manager
or other TCP/IP applications. The Switch's default IP address is 10.90.90.90. You can change the Switch’s default IP
address to fit into your networking address range.
The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be
found by entering the command "show switch" into the command line interface, as shown below.
20
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
DWS-3160-24PC:admin#show switch
Command: show switch
Device Type
: DWS-3160-24PC Gigabit Ethernet Switch
MAC Address
: 00-11-22-33-45-67
IP Address
: 10.90.90.90 (Manual)
VLAN Name
: default
Subnet Mask
: 255.0.0.0
Default Gateway
: 0.0.0.0
Boot PROM Version
: Build 1.00.001
Firmware Version
: Build 1.00.037
Hardware Version
: A1
System Name
:
System Location
:
System Uptime
: 0 days, 0 hours, 0 minutes, 34 seconds
System Contact
:
Spanning Tree
: Disabled
GVRP
: Disabled
IGMP Snooping
: Disabled
MLD Snooping
: Disabled
VLAN Trunk
: Disabled
Telnet
: Enabled (TCP 23)
Web
: Enabled (TCP 80)
SNMP
: Disabled
SSL Status
: Disabled
CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a All
Figure 4- 6. The ‘show switch’ command
The IP address of the Switch must be configured before it can be managed, by the user, via the Web User Interface.
An example to change the IP address of the Switch to ’10.90.90.90’, using a subnet mask of ‘255.0.0.0’:
DWS-3160-24PC:admin#config ipif System ipaddress 10.90.90.91/8
Command: config ipif System ipaddress 10.90.90.91/8
Success.
DWS-3160-24PC:admin#
Figure 4- 7. To change the IP address
1. At the CLI command prompt, enter the ‘config ipif System ipaddress 10.90.90.91/8’ command and press
‘Enter’. This will change the IP address of the Switch to 10.90.90.91.
2. Also notice the subnet mask’s notation method. Here we use the value ‘/8’ which means that the subnet mask
will be change to 255.0.0.0 using the CIDR notation.
3. Alternatively, if you don’t know the CIDR notation for your subnet mask, you can also simply type out the
subnet mask. For example: ‘config ipif System ipaddress 10.90.90.91/255.0.0.0’.
The Switch can now be configured and accessed using Telnet or the Web-based management.
The Switch’s IP address can also automatically be obtained by using the BOOTP or DHCP protocol.
21
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Connecting using SNMP
The Switch can be managed with an SNMP-compatible console program. The Simple Network Management Protocol
(SNMP) operates on the Application Layer of the OSI model and is designed specifically for managing and monitoring
network devices. The SNMP agent decodes the incoming SNMP messages and responds to requests with MIB
objects stored in the database. The SNMP agent updates the MIB objects to generate statistics and counters.
D-Link provides a professional network management software package, called D-View 6.0 that uses SNMP to
®
connect, configure, manage and monitor this Switch. The D-View 6.0 SNMP Network Management System is a
software tool that facilitates the central administration of a network with various SNMP-enabled devices.
Figure 4- 8. D-Link’s D-View SNMP Software
Managed devices that support SNMP include software (referred to as an agent), which runs locally on the device. A
defined set of variables (managed objects) is maintained by the SNMP agent and used to manage the device. These
objects are defined in a Management Information Base (MIB), which provides a standard presentation of the
information controlled by the on-board SNMP agent. SNMP defines both the format of the MIB specifications and the
protocol used to access this information over the network.
This Switch supports SNMP Versions 1, 2c, and 3 alternatively known as SNMPv1, SNMPv2c and SNMPv3. The
administrator may specify which version of SNMP to use to monitor and control the Switch. The three versions of
SNMP vary in the level of security provided between the management station and the network device.
In SNMPv1 and SNMPv2c, user authentication is accomplished using 'community strings', which function like
passwords. The remote user SNMP application and the Switch’s SNMP must use the same community string. SNMP
packets from any station that has not been authenticated are ignored (dropped).
The default community strings for the Switch used for SNMPv1 and SNMPv2c are:
•
public - Allows authorized management stations to retrieve MIB objects.
•
private - Allows authorized management stations to retrieve and modify MIB objects.
22
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
DWS-3160-24PC:admin# show snmp community
Command: show snmp community
SNMP Community Table
Community Name
View Name
Access Right
--------------------------------
--------------------------------
------------
private
public
CommunityView
CommunityView
read_write
read_only
Total Entries: 2
DWS-3160-24PC:admin#
Figure 4- 9. To view the SNMP community strings
SNMPv3 uses a more sophisticated authentication process that is separated into two parts.
1. The first part is to maintain a list of users and their attributes that are allowed to act as SNMP managers.
2. The second part describes what each user on that list can do as an SNMP manager.
The Switch allows groups of users to be created and configured with a shared set of privileges. The SNMP version
may also be configured for a specific group of SNMP managers. A group of SNMP managers can be created to view
read-only information or to receive traps using SNMPv1 while assigning a higher level of security to another group,
granting read/write privileges using SNMPv3.
Using SNMPv3, individual users or groups of SNMP managers can be allowed to perform or be restricted from
performing specific SNMP management functions. The functions allowed or restricted are defined using the Object
Identifier (OID) associated with a specific MIB. An additional layer of security is available for SNMPv3 in which SNMP
messages may be encrypted.
Traps
Traps are messages that alert network personnel of events that occur on the Switch. The events can be as serious as
a reboot (someone accidentally turned OFF the Switch), or less serious like a port status change. The Switch
generates traps and sends them to the trap recipient (or network manager). Typical traps include trap messages for
Authentication Failure, Topology Change and Broadcast/Multicast Storm.
Management Information Base (MIB)
The Management Information Base (MIB) stores management and counter information. The Switch uses the standard
MIB-II Management Information Base module. Consequently, values for MIB objects can be retrieved from any
SNMP-based network management software. In addition to the standard MIB-II, the Switch also supports its own
proprietary enterprise MIB as an extended Management Information Base. The proprietary MIB may also be retrieved
by specifying the MIB Object Identifier. MIB values can be either read-only or read-write.
23
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Connecting using the Web User Interface
All software functions of the Switch can be managed, configured, and monitored via the embedded Web-based
(HTML) interface. This can be done from any remote station on the network through a standard web browser, such as
Internet Explorer (version 5.5 and later), Mozilla Firefox (version 2.0 and later), Safari (version 4.0 and later), or
Google Chrome (version 6.0 and later). The browser acts as a universal access tool and can communicate directly
with the Switch using the HTTP protocol.
All the software features that can be configured using the Command Line Interface can also be configured using the
Web User Interface. The Web User Interface is thus an alternative configuration method for the lesser analytical
users.
Logging onto the Web Manager
To access the Web User Interface the user simply runs the standard web browser and enter the Switch’s IP address
into the address bar of the browser and press the ‘Enter’ key.
Figure 4- 10. Displays entering the IP address in Internet Explorer
NOTE: The factory default IP address is 10.90.90.90.
This will open the user authentication window, as seen below.
Figure 4- 11. Enter Network Password window
As there is no default User name or Password, click OK to proceed. This will open the Web-based User Interface.
The Switch management features available in the Web-based manager are explained below.
24
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Areas of the User Interface
After a successful connection to the Web User Interface has been made, the following page should be displayed.
AREA 2
AREA 1
AREA 3
Figure 4- 12. Main Web Manager window
On this page we will find three main areas to observe.
Area Number
Function
AREA 1
This area is divided up into two main sections. The LAN section can be used to configure anything
that is related to the Ethernet network segments. The WLAN section can be used to configure
anything that is related to the Wireless LAN segments. Both sections have Folder links that can be
expanded and both sections have Window links that will navigate the user to a specific feature’s
configuration page. This can be done by simply click on them with the mouse pointer.
AREA 2
This area displays a graphical, real-time image of the front panel of the Switch. When clicking on
active ports, in this image, the user will be navigated to the port activity page for the specific port.
Also in this area, on the bottom left, the user can access the Save and Tools pages by simply
clicking on them. On the top right, the user can also select the Refresh Interval time for this area.
Click Apply to accept the change made.
AREA 3
This area is where the magic really happens. After clicking on a Window link, in Area 1, this area
will display the configuration page for the specific features that can be configured or monitored.
25
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Chapter 5
D-Link Unified Access System
D-Link Unified Access System Components
D-Link Unified Access System Topology
The D-Link Unified Access System is a wireless local area network (WLAN) solution that enables WLAN deployment
while providing state-of-the-art wireless networking features. It is a scalable solution that provides secure wireless
connectivity and seamless layer 2 and layer 3 roaming for end users.
D-Link Unified Access System Components
The D-Link Unified Access System components include the D-Link Unified Switch and the D-Link Access Point (AP).
With the default D-Link License Management Service (DLMS) agreement, this Switch can manage up to 12 unified
Access Points. After an optional upgrade of the license agreement, purchased from D-Link, this Switch can manage
up to 48 unified Access Points per unified Switch. The most powerful feature of this Switch is that up to 4 Switches
can form a cluster to manage up to 192 unified Access Points centrally with a single IP address.
The switch tracks the status and statistics for all associated WLAN traffic and devices. You can configure up to 4 peer
D-Link Unified Switches that share various information about APs and their associated wireless clients. The peer
Unified Switches can be directly connected to each other, separated by Layer 2 bridges, or located in different IP
Subnets. Wireless clients can roam among the access points managed by peer Unified Switches without losing
network connections. Whether or not you have a peer group, the D-Link Unified Access System can support a total of
8000 wireless clients
D-Link Unified Switch
The D-Link Unified Switch handles Layer 2+ switching functions for traffic on the wired and wireless LAN. The Unified
Switch user interface allows you to configure and monitor all AP settings and maintain a consistent configuration
among all APs in the network.
The Unified Switch supports advanced data path connectivity, mobility control, security safeguards, control over radio
and power parameters, and management features for both network and element control. The Unified Switch allows
you to control the discovery, validation, authentication, and monitoring of peer Unified Switches, D-Link Access Points,
and clients on the WLAN, including discovery and status of rogue APs and clients.
The D-Link Unified Access System works with the following D-Link switches:
•
DWS-3160-24TC
•
DWS-3160-24PC
D-Link Access Point
The D-Link Access Point can operate in one of two modes: Standalone Mode or Managed Mode.
•
In Standalone Mode, the D-Link Access Point acts as an individual access point in the network, and you
manage it by connecting to the AP and using the Administrator Web User Interface (UI) or Command Line
Interface (CLI).
•
In Managed Mode, the D-Link Access Point is part of the D-Link Unified Access System, and you manage it
by using the D-Link Unified Switch. If an AP is in Managed Mode, the Administrator Web UI services on the
AP are disabled. Access is limited to the CLI through Telnet.
The Standalone Mode is appropriate for small networks with only a few APs. The Managed Mode is useful for any size
network. If you start out with D-Link Access Points in Standalone Mode, you can easily transition the APs to Managed
Mode when you add a Unified Switch to the network. By using the AP in Managed Mode, you can centralize AP
26
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
management and streamline the AP upgrade process by pushing configuration profiles and software upgrades from
the Unified Switch to the managed APs. The Web UI Reference Guide and the CLI Reference Guide primarily
describes the D-Link Access Point in Managed Mode.
The D-Link Unified Access System works with the following D-Link access points:
•
DWL-3600AP
•
DWL-8600AP
•
DWL-6600AP
Each access point supports up to eight virtual access points (VAPs) on each radio. The VAP feature allows you to
segment each physical access point into eight logical access points (per radio) that each supports a unique SSID,
VLAN ID, and security policy.
WLAN Visualization
The D-Link Unified Access System includes the WLAN Visualization tool, which provides a graphical representation of
your wireless network through a Web browser. WLAN Visualization detects and displays the D-Link Unified Switch, DLink Access Points, other access points, and all wireless clients associated with the D-Link Access Point. You can
import information about your building layout to customize the network view.
The figure below shows an example of a floor plan and network with a D-Link Unified Switch that manages two APs.
The graph also shows a peer switch and a rogue AP in the network.
Figure 5-1 WLAN Visualization
The WLAN Visualization tool provides an AP power display with color-coded channels to help you determine where to
physically place access points to reduce interference or increase coverage on your WLAN.
27
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
D-Link Unified Access System Topology
The WLAN network topology you use depends on the size and requirements of your network. Small-to-medium
networks might require only one Unified Switch that manages a few D-Link Access Points. For larger networks that
need greater roaming capabilities for wireless clients, a deployment with multiple peer switches that each manages
several APs might be appropriate.
Single Unified Switch Deployment
When you deploy a D-Link Access Point, the D-Link Unified Switch can automatically detect the AP and assign a
default profile, which includes automatic RF channel selection and automatic power adjustment.
Figure 5-2 One Unified Switch with Three APs
When the APs are on the same subnet and have the same SSID, wireless clients can seamlessly roam among the
three APs with no interruption in network access. The client keeps the same IP address and does not need to reauthenticate when it moves into the broadcast area of a different AP. Configuration changes to the APs are managed
by the switch simultaneously or on a per-AP basis.
Peer Unified Switch Deployment
To support larger networks, you can configure up to four switches as peers, which increases the size and range of the
WLAN. The Unified Switch and the APs it manages do not need to be on the same subnet.
28
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Figure 5-3 Unified Access System Deployment with 3 Unified Switches
Peer Unified Switches share information about APs and allow Layer 3 roaming among them. To support this, peer
Unified Switches establish IPv4 tunnels so that the wireless client keeps the same IP address even when the client
associates with an access point in a different subnet. The Layer 3 roaming service allows wireless phone users to
roam between access points connected to different subnets without dropping calls.
29
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Chapter 6
Appendix Section
Appendix A – Technical Specifications
General
Feature
Detailed Description
Standards
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
IEEE 802.3z 1000BASE-T (SFP “Mini GBIC”)
IEEE 802.1D/2004/Spanning Tree (802.1s, 802.1w)
IEEE 802.1Q-2005 VLAN
IEEE 802.1p Priority Queues
IEEE 802.1X Network Access Control
IEEE 802.3 Nway Auto-negotiation
IEEE 802.3ad Link Aggregation Control
IEEE 802.3x Full-duplex Flow Control
IEEE 802.1u Fast Ethernet
Protocols
CSMA/CD
Data Transfer Rates:
Ethernet
Fast Ethernet
Gigabit Ethernet
Half-duplex
10 Mbps
100Mbps
-------------
Network Cables
Cat.5 Enhanced for 1000BASE-T
UTP Cat.5, Cat. 5 Enhanced for 100BASE-TX
UTP Cat.3, 4, 5 for 10BASE-T
EIA/TIA-568 100-ohm screened twisted-pair (STP)(100m)
Full-duplex
20Mbps
200Mbps
2000Mbps
Physical and Environmental
Feature
Detailed Description
Internal Power Supply
DWS-3160-24TC: 100-240VAC, 50-60Hz, 60 Watt
DWS-3160-24PC: 100-240VAC, 50-60Hz, 589 Watt
Optional Redundant
Power Supply
One connector in rear panel to install an optional external RPS. When internal power
fails, the optional external RPS will automatically take over all the power supply
immediately.
DWS-3160-24TC: DPS-200
DWS-3160-24PC: DPS-700
Fans
DWS-3160-24TC: 2 Fans
DWS-3160-24PC: 4 Fans
Power Consumption
DWS-3160-24TC: 37.7 Watts (Max.)
DWS-3160-24PC: 467.3 Watts (Max.)
Operating Temperature
0~50°C
Storage Temperature
-40~70°C
Humidity
Operation: 10%-90% RH non-condensing
30
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Storage: 5% ~ 90% RH non-condensing
Dimensions
DWS-3160-24TC: 440mm (W) x 210mm (D) x 44mm (H)
DWS-3160-24PC: 440mm (W) x 310mm (D) x 44mm (H)
Weight
DWS-3160-24TC: 2.552kg.
DWS-3160-24PC: 5.242kg.
SD Card
At least 4G supported.
Power-over-Ethernet
IEEE 802.3af and 802.3at compliance.
Provides up to 15.4 Watts for 802.3af compliant devices.
Provides up to 30 Watts for 802.3at compliant devices.
System PoE power budget: 740W.
Auto-discover the connection of PD and immediately providing power.
Auto-disable port if the port current is over 350mA.
Feeding power over pins 1, 2, 3 & 6 of 8 wires of UTP cables.
Supports dynamic PoE power allocation.
Support per-port PoE priority setting, default setting all ports low priority.
EMI
CE Class A, FCC Class A, VCCI Class A, C-Tick Report
Safety
UL, CB Report, CSA International Mark
Performance
Feature
Detailed Description
Transmission Method
Store-and-forward
Packet Buffer
2 Mbyte (Max)
Maximum Forwarding
Rate
DWS-3160-24TC: 35.72 million packets per second.
DWS-3160-24PC: 35.72 million packets per second.
Switching Capability
DWS-3160-24TC: 48Gbps
DWS-3160-24PC: 48Gbps
Priority Queues
8 Priority Queues per port
MAC Address Table
Supports 16K MAC addresses
Wire Speed
Full-wire speed (full-duplex) operation on all ports including Gigabit ports.
Virtual Stacking /
Clustering
Support D-Link Single IP Management v1.6
Able to manage up to 4 Unified Switches in a virtual stack with a single IP address.
Manage up to 32 devices in a virtual stack with a single IP address.
LED Indicators
Location
LED Indicative
Color
Status
Description
Per Device
Power
Green
Solid Light
Power On
Light off
Power Off
Solid Light
Console on
Light off
Console off
Blinking
When switch detects that RPS is
connected
Solid Light
RPS in using
Console
RPS
Green
Green
31
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Fan Err
Light off
RPS off
Blinking
When any of the fans has failed
Light off
When all fans work normally
Solid Light
A LED Mode Select Button to switch
Link/Act/Speed Mode
Solid Light
A LED Mode Select Button to switch
PoE Mode
Solid Light
When there is a secure connection (or
link) to 1000Mbps Ethernet device at
any of the ports.
Blinking
When there is reception or
transmission of data occurring at
1000Mbps.
Solid Light
When there is a secure connection (or
link) to 10/100Mbps Ethernet device
at any of the ports.
Blinking
When there is reception or
transmission of data occurring at
10/100Mbps.
Off
Light off
No link.
Green
Solid Light
Power feeding.
Orange
Solid Light
Error Condition.
Off
Light Off
No Power feeding.
Green
Solid Light
When there is a secure connection (or
link) to 1000Mbps Ethernet device at
any of the ports.
Blinking
When there is reception or
transmission of data occurring at
1000Mbps.
Solid Light
When there is a secure connection (or
link) to 100Mbps Ethernet device at
any of the ports.
Blinking
When there is reception or
transmission of data occurring at
100Mbps.
Off
Light off
No link
Green
Solid Light
SD card plug-in
Blinking
Read/Write
Light off
No link
Solid Light
SD card failure
Red
Port LED Mode
Indicator
LED Per
Link/Act/Speed
10/100/1000 Mbps Mode
Port
Green
Green
Orange
PoE Mode
(DWS-3160-24PC)
LED Per SFP Port Link/Act
Orange
SD
Red
Port Functions
Feature
Detailed Description
Console Port
RJ-45 interface for out-of-band CLI configuration
Copper Ports
(10/100/1000Mbps)
Compliant to following standards:
•
IEEE 802.3 compliance
•
IEEE 802.3u compliance
32
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
•
SFP Ports
(1000Mbps)
IEEE 802.3ab compliance
•
Support Half/Full-Duplex operations
•
Auto-negotiation, Auto MDI/MDIX
•
IEEE 802.3x Flow Control support for Full-Duplex mode, Back Pressure when HalfDuplex mode, and Head-of-line blocking prevention
Compliant to following standards:
•
IEEE 802.3z compliance
•
IEEE 802.3x Flow Control support for Full-Duplex mode.
•
Support Auto-negotiation for Full-Duplex/ flow control operations
SFP Transceivers Supported:
•
DEM-310GT (1000BASE-LX, Single-mode, 10km)
•
DEM-311GT (1000BASE-SX, Multi-mode, 500m)
•
DEM-312GT2 (1000BASE-SX, Multi-mode, 2km)
•
DEM-314GT (1000BASE-LHX, Single-mode, 50km)
•
DEM-315GT (1000BASE-ZX, Single-mode, 80km)
•
DEM-330T/R (WDM transceiver, Single-Mode 10km)
•
DEM-331T/R (WDM transceiver, Single-Mode 40km)
•
DGS-712 (1000BASE-T,Copper, 100m)
•
DEM-210 (100BASE-FX, Single-Mode 15km)
•
DEM-211 (100BASE-FX, Multi-mode, 2km)
•
DEM-220T/R (100BASE-BX, Single-Mode, 20km)
Wireless Functions
Feature
Detailed Description
Max. AP per Switch
Default DLMS: 12 Unified Access Points.
Upgraded DLMS: 48 Unified Access Points.
Max. Users per Switch Up to 1024 Tunneled users
Up to 2048 non-Tunneled users
Multiple SSIDs per AP Up to 16 SSIDs per radio, 32 SSIDs per AP
Multiple SSIDs per
Switch
Up to 64 SSIDs can be configured and stored on the Switch.
Visualized AP
Management Tool
Support up to 16 JPEG files.
Unified AP Support
DWL-8600AP, DWL-3600AP, DWL-6600AP
Wireless Standards
IEEE 802.11a, 802.11b, 802.11g, 802.11d, 802.11h, 802.11n
Security Modes
None
WEP - Open System
WEP – Shared Key
WEP – 802.1x (Dynamic WEP)
WPA/WPA2 – Shared Key (Personal)
WPA/WPA2 – 802.1x (Enterprise)
802.1X EAP Types
EAP-MD5, EAP-TLS, EAP-TTLS, EAP-FAST, EAP-SIM, PEAP-GTC, PEAP-TLS, PEAPMS-CHAPv2
Captive Portal
Support Radius and Local User Databases.
Up to 128 users in the Local Database.
33
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Up to 1024 concurrent on-line users.
Support up to 6 customized web pages.
34
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Appendix B – Cables and Connectors
Ethernet Cable
When connecting the Switch to another switch, a bridge or hub, a normal cable is necessary. Please review these
products for matching cable pin assignment.
The following diagrams and tables show the standard RJ-45 receptacle/connector and their pin assignments.
Figure B- 1. The standard RJ-45 port and connector
RJ-45 Pin Assignments
Contact
MDI-X Port
MDI-II Port
1
RD+ (receive)
TD+ (transmit)
2
RD- (receive)
TD- (transmit)
3
TD+ (transmit)
RD+ (receive)
4
1000BASE-T
1000BASE-T
5
1000BASE-T
1000BASE-T
6
TD- (transmit)
RD- (receive)
7
1000BASE-T
1000BASE-T
8
1000BASE-T
1000BASE-T
35
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Console Cable
When connecting the Switch a PC, a Console cable is necessary. The following diagrams and tables show the
standard Console-to-DJ-45 receptacle/connector and their pin assignments.
Figure B- 2. Console-to-RJ-45 Cable
Console-RJ-45 Pin Assignments
Pin
Console (DB9/RS232)
RJ-45
1
Not Used
Not Used
2
RXD
Not Used
3
TXD
TXD
4
Not Used
GND
5
GND (shared)
GND
6
Not Used
RXD
7
Not Used
Not Used
8
Not Used
Not Used
36
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Redundant Power Supply (RPS) Cable
When connecting the Switch to a Redundant Power Supply, an RPS cable is necessary. Please review these products
for matching cable pin assignment.The following diagrams and tables show the standard RPS receptacle/connector
and their pin assignments.
14-pin DC power cable
Figure B- 3. Redundant Power Supply (RPS) 14-pin DC Power Cable
RPS 14-pin DC Power Cable Pin Assignments
Pin
Device
DPS-200
1
GND
GND
2
NC
NC
3
+12V
+12V
4
+12V
+12V
5
+12V
+12V
6
+12V
+12V
7
GND
GND
8
GND
GND
9
NC
Power Good
10
NC
Power Present
11
Power Good
NC
12
Power Present
NC
13
GND
GND
14
GND
GND
37
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
22-pin DC power cable
Figure B- 4. Redundant Power Supply (RPS) 22-pin DC Power Cable
RPS 22-pin DC Power Cable Pin Assignments
Pin
Device
DPS-700
1
-54Vrtn
-54Vrtn
2
-54V
-54V
3
+12V
+12V
4
+12V
+12V
5
+12V
+12V
6
+12V
+12V
7
NC/GND
GND
8
+12Ven
+12Ven
9
LS-54V
LS-54V
10
-54V
-54V
11
-54Vrtn
-54Vrtn
12
GND
NC/GND
13
GND
GND
14
RPS Present
Status_2
15
Status_1
RPS PG
16
Status_2
RPS Present
17
RPS PG
Status_1
18
GND
GND
19
+12VRTNsen
+12VRTNsen
20
LS+12V
LS+12V
21
-54Vsen
-54Vsen
22
-54VRTNsen
-54VRTNsen
38
DWS-3160 Series Gigabit Ethernet Unified Switch Hardware Installation Guide
Appendix C – Module Specifications and Cable
Lengths
Use the following table to as a guide for the module specs and maximum cable lengths.
Standard
Media Type
Maximum Distance
Mini-GBIC
1000BASE-LX, Single-mode fiber module
1000BASE-SX, Multi-mode fiber module
1000BASE-LH, Single-mode fiber module
1000BASE-ZX, Single-mode fiber module
10km
550m / 2km
50km
80km
1000BASE-T
Category 5e UTP Cable
100m
100BASE-TX
Category 5 UTP Cable (100 Mbps)
100m
10BASE-T
Category 3, 4 or 5 UTP Cable (10 Mbps)
100m
DEM-310GT
1000BASE-LX, Single-mode
10km
DEM-311GT
1000BASE-SX, Multi-mode
500m
DEM-312GT2
1000BASE-SX, Multi-mode
2km
DEM-314GT
1000BASE-LH, Single-mode
50km
DEM-315GT
1000BASE-ZX, Single-mode
80km
DEM-210
100BASE-FX, Single-mode
15km
DEM-330T
TX-1550/RX-1310 nm, Single-mode
Up to 10km
DEM-330R
TX-1310/RX-1550 nm, Single-mode
Up to 10km
DEM-331T
TX-1550/RX-1310 nm, Single-Mode
Up to 40km
DEM-331R
TX-1310/RX-1550 nm, Single-Mode
Up to 40km
DGS-712
1000BASE-T, Copper
100m
Network pluggable optical modules meet the following regulatory requirements:
•
Class 1 Laser Product
•
EN60825-1+A2:2001 or later, European laser standard
•
FCC 21 CFR Chapter 1, Subchapter J in accordance with FDA & CDRH requirements
39
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:


Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates,
U.S. Military Installations, or addresses with an APO or FPO.
Limited Warranty: D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in
workmanship and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”),
except as otherwise stated herein.
Limited Lifetime Warranty for the product is defined as follows:



Hardware: For as long as the original customer/end user owns the product, or five (5) years after product discontinuance, whichever occurs first
(excluding power supplies and fans)
Power supplies and fans: Three (3) Year
Spare parts and spare kits: Ninety (90) days
The customer's sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to
repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual purchase price paid. Any
repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical
make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably
determines is substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or replacement hardware will be
warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer, and is subject to the same limitations and exclusions.
If a material defect is incapable of correction, or if D-Link determines that it is not practical to repair or replace the defective Hardware, the actual price
paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part
thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.
Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current
functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period
of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in
its documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be
free of physical defects. The customer's sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be,
at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional
specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise agreed
by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by
D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations
and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the
non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the nonconforming Software (and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given
automatically terminates.
Non-Applicability of Warranty: The Limited Warranty provided hereunder for Hardware and Software portions of D-Link's products will not be applied to
and does not cover any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link,
the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold "As-Is"
without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the
contrary.
Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has
expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:

The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient
detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product)
if the product is not registered.

The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the customer in resolving
any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material Authorization (“RMA”)
number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.com/.

After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it
will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or
accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.

The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be
rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595
Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or
replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be
prepaid by D-Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available
upon request and provided shipping charges are prepaid by the customer.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA
number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any
product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or nonconforming.
What Is Not Covered: The Limited Warranty provided herein by D-Link does not cover: Products that, in D-Link’s judgment, have been subjected to
abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not
contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial
installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product,
and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware,
software, firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance
or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.
While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link
Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT
ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A
PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO NINETY (90) DAYS. EXCEPT AS EXPRESSLY
COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE
OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.
Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE,
STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF
ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS
OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER
EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA
CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM
THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF
D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED
WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM LIABILITY OF DLINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING
EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES,
EXPRESS, IMPLIED OR STATUTORY.
Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of
incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This
Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state.
Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective
owners.
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used
to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated
by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice. Copyright 2004 by D-Link
Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning: This is a Class A product. In a residential environment, this product may cause radio interference, in which case the user may be
required to take adequate measures.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a particular installation. Operation of this equipment in a residential
environment is likely to cause harmful interference to radio or television reception. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding
local D-Link office.
Product Registration
Register your D-Link product online at http://support.dlink.com/register/
Product registration is entirely voluntary and failure to complete or return this form will
not diminish your warranty rights.
Tech Support
Technical Support
You can find software updates and user documentation on the DLink website.
D-Link provides free technical support for customers within the
United States and within Canada for the duration of the service
period, and warranty confirmation service, during the warranty
period on this product. U.S. and Canadian customers can contact
D-Link technical support through our website, or by phone.
Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
USA - 877-DLINK-55 (877-354-6555)
D-Link Technical Support over the Internet:
http://support.dlink.com
Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
877-354-6560
D-Link Technical Support over the Internet:
http://support.dlink.com
Technical Support
United Kingdom (Mon-Fri)
Home Wireless/Broadband 0871 873 3000 (9.00am–06.00pm, Sat 10.00am-02.00pm)
Managed, Smart, & Wireless Switches, or Firewalls 0871 873 0909 (09.00am – 05.30pm)
(BT 10ppm, other carriers may vary.)
Ireland (Mon-Fri)
All Products 1890 886 899 (09.00am-06.00pm, Sat 10.00am-02.00pm)
€0.05ppm peak, €0.045ppm off peak Times
Internet
http://www.dlink.co.uk
ftp://ftp.dlink.co.uk
Technische Unterstützung
Deutschland:
Österreich:
Schweiz:
Web:
http://www.dlink.de
Telefon:
+49(0)1805 2787
Zeiten:
Mo. –Fr. 09:00 – 17:30 Uhr
Web:
http://www.dlink.at
Telefon:
+43(0)820 480084
Zeiten:
Mo. –Fr. 09:00 – 17:30 Uhr
Web:
http://www.dlink.ch
Telefon:
+41(0)848 331100
Zeiten:
Mo. –Fr. 09:00 – 17:30 Uhr
0,14 € pro Minute
0,116 € pro Minute
0,08 CHF pro Minute
* Gebühren aus Mobilnetzen und von anderen Providern können abweichen.
Assistance technique
Assistance technique D-Link sur internet :http://www.dlink.fr
Assistance technique D-Link par téléphone : 0820 0803 03
0.12 € TTC/min depuis un poste fixe
Du lundi au vendredi de 9h à 19h (hors jours fériés)
Asistencia Técnica
Asistencia Técnica Telefónica de D-Link: +34 902 30 45 45
0,067 €/min
De Lunes a Viernes de 9:00 a 19:00
http://www.dlink.es
Supporto tecnico
Supporto Tecnico dal lunedì al venerdì dalle ore 9.00 alle ore 19.00 con orario
continuato
Telefono: 02 87366396
http://www.dlink.it/support
TECHNISCHE ONDERSTEUNING
Technische ondereuning voor klanten in Nederland:
www.dlink.nl / 0900 501 2007 / €0.15per minuut.
Tech Support for customers within Belgium:
www.dlink.be / 070 66 06 40 / €0.175per minuut(spitsuren), €0.0875per minuut(daluren)
Technische ondereuning voor klanten in Luxemburg:
www.dlink.be / +32 70 66 06 40
Pomoc techniczna
Telefoniczna pomoc techniczna firmy D-Link: 0 801 022 021
Pomoc techniczna firmy D-Link świadczona przez Internet:
http://www.dlink.eu/support/
Technická podpora
Web: http://www.dlink.cz/support/
E-mail: support@dlink.cz
Telefon ČR: +420 211 151 640 nebo SK: +421 (0)692 147 110
Telefonická podpora je v provozu: PO - PÁ od 09:00 do 17:00
Volání je zpoplatněno dle příslušných tarifů Vašeho operátora.
Technikai Támogatás
Tel. : 06 1 461-3001
Fax : 06 1 461-3004
Land Line 14,99 HUG/min - Mobile 49.99,HUF/min
email : support@dlink.hu
URL : http://www.dlink.hu
Teknisk Support
D-Link Teknisk Support over Internett: http://www.dlink.no
D-Link Teknisk telefonsupport: 820 00 755
(Hverdager 08:00-20:00)
Teknisk Support
D-Link teknisk support over telefonen: Tlf.: 9013 8899
Normale åbningstider: Hverdage kl. 08:00 - 20:00
D-Link teknisk support på Internettet: http://www.dlink.dk
Teknistä tukea asiakkaille Suomessa:
Internetin kautta : http://www.dlink.fi
Arkisin klo. 9 - 21
Numerosta : 0600 155 57
Teknisk Support
D-Link Teknisk Support via Internet: http://www.dlink.se
D-Link Teknisk Support via telefon: 0900-100 77 00
Vardagar 08:00-20:00
Assistência Técnica
Assistência Técnica da D-Link na Internet:
http://www.dlink.pt
e-mail: soporte@dlink.es
Τεχνική Υποστήριξη
D-Link Hellas Support Center
Κεφαλληνίας 64, 11251 Αθήνα,
Τηλ: 210 86 11 114 (Δευτέρα- Παρασκευή 09:00-17:00)
Φαξ: 210 8611114
http://www.dlink.gr/support
Tehnička podrška
Hvala vam na odabiru D-Link proizvoda. Za dodatne informacije, podršku
i upute za korištenje uređaja, molimo vas da posjetite D-Link internetsku
stranicu na www.dlink.eu
www.dlink.biz/hr
Tehnična podpora
Zahvaljujemo se vam, ker ste izbrali D-Link proizvod. Za vse nadaljnje
informacije, podporo ter navodila za uporabo prosimo obiščite D-Link - ovo
spletno stran www.dlink.eu
www.dlink.biz/sl
Suport tehnic
Vă mulţumim pentru alegerea produselor D-Link. Pentru mai multe informaţii,
suport şi manuale ale produselor vă rugăm să vizitaţi site-ul D-Link www.dlink.eu
www.dlink.ro
Technical Support
You can find software updates and user do cumentation on the D-Link website.
Tech Support for customers in
Australia:
Tel: 1300-766-868
24/7 Technical Support
Web: http://www.dlink.com.au
E-mail: support@dlink.com.au
India:
Tel: +91-22-27626600
Toll Free 1800-22-8998
Web: www.dlink.co.in
E-Mail: helpdesk@dlink.co.in
Singapore, Thailand, Indonesia, Malaysia,
Philippines, Vietnam:
Singapore - www.dlink.com.sg
Thailand - www.dlink.co.th
Indonesia - www.dlink.co.id
Malaysia - www.dlink.com.my
Philippines - www.dlink.com.ph
Vietnam - www.dlink.com.vn
Korea:
Tel : +82-2-2028-1810
Monday to Friday 9:00am to 6:00pm
Web : http://d-link.co.kr
E-mail : g2b@d-link.co.kr
New Zealand:
Tel: 0800-900-900
24/7 Technical Support
Web: http://www.dlink.co.nz
E-mail: support@dlink.co.nz
South Africa and Sub Sahara Region:
Tel: +27 12 661 2025
08600 DLINK (for South Africa only)
Monday to Friday 8:30am to 9:00pm South Africa
Time
Web: http://www.d-link.co.za
E-mail: support@d-link.co.za
Saudi Arabia (KSA):
Tel: +966 01 217 0008
Fax: +966 01 217 0009
Saturday to Wednesday 9.30AM to 6.30PM
Thursdays 9.30AM to 2.00 PM
E-mail: Support.sa@dlink-me.com
D-Link Middle East - Dubai, U.A.E.
Plot No. S31102,
Jebel Ali Free Zone South,
P.O.Box 18224, Dubai, U.A.E.
Tel: +971-4-8809022
Fax: +971-4-8809066 / 8809069
Technical Support: +971-4-8809033
General Inquiries: info.me@dlink-me.com
Tech Support: support.me@dlink-me.com
Egypt
1, Makram Ebeid Street - City Lights Building
Nasrcity - Cairo, Egypt
Floor 6, office C2
Tel.: +2 02 26718375 - +2 02 26717280
Technical Support: +2 02 26738470
General Inquiries: info.eg@dlink-me.com
Tech Support: support.eg@dlink-me.com
Kingdom of Saudi Arabia
Office # 84 ,
Al Khaleej Building ( Mujamathu Al-Khaleej)
Opp. King Fahd Road, Olaya
Riyadh - Saudi Arabia
Tel: +966 1 217 0008
Technical Support:
+966 1 2170009 / +966 2 6522951
General Inquiries: info.sa@dlink-me.com
Tech Support: support.sa@dlink-me.com
Pakistan
Islamabad Office:
61-A, Jinnah Avenue, Blue Area,
Suite # 11, EBC, Saudi Pak Tower,
Islamabad - Pakistan
Tel.: +92-51-2800397, 2800398
Fax: +92-51-2800399
Karachi Office:
D-147/1, KDA Scheme # 1,
Opposite Mudassir Park, Karsaz Road,
Karachi – Pakistan
Phone: +92-21-34548158, 34326649
Fax: +92-21-4375727
Technical Support: +92-21-34548310, 34305069
General Inquiries: info.pk@dlink-me.com
Tech Support: support.pk@dlink-me.com
Technical Support
You can find software updates and user documentation on the D-Link website.
Tech Support for customers in
Iran
Unit 5, 5th Floor, No. 20, 17th Alley , Bokharest
St. , Argentine Sq. ,
Tehran IRAN
Postal Code : 1513833817
Tel: +98-21-88880918,19
+98-21-88706653,54
General Inquiries: info.ir@dlink-me.com
Tech Support: support.ir@dlink-me.com
Morocco
M.I.T.C
Route de Nouaceur angle RS et CT 1029
Bureau N° 312 ET 337
Casablanca , Maroc
Phone : +212 663 72 73 24
Email: support.na@dlink-me.com
Lebanon RMA center
Dbayeh/Lebanon
PO Box:901589
Tel: +961 4 54 49 71 Ext:14
Fax: +961 4 54 49 71 Ext:12
Email: taoun@dlink-me.com
Bahrain
Technical Support: +973 1 3332904
Kuwait:
Technical Support: + 965 22453939 / +965
22453949
Türkiye Merkez İrtibat Ofisi
Ayazağa Maslak yolu
Erdebil Cevahir İş Merkezi No: 5/A Ayazağa /
Maslak İstanbul
Tel: +90 212 2895659
Ücretsiz Müşteri Destek Hattı: 0 800 211 00 65
Web:www.dlink.com.tr
Teknik Destek: support.tr@dlink.com.tr
Israel
20 ‫רח' המגשימים‬
49348 ‫ פ"ת‬,‫קרית מטלון‬
7060 .‫ד‬.‫ת‬
77-11-277-073 :‫טלפון‬
info@dlink.co.il :‫מאייל כללי‬-‫אי‬
support@dlink.co.il :‫מאייל תמיכה‬-‫אי‬
Техническая поддержка
Обновления программного обеспечения и документация доступны на Интернет-сайте D-Link.
D-Link предоставляет бесплатную поддержку для клиентов в течение гарантийного срока.
Клиенты могут обратиться в группу технической поддержки D-Link по телефону или через
Интернет.
Техническая поддержка D-Link:
+7(495) 744-00-99
Техническая поддержка через Интернет
http://www.dlink.ru
e-mail: support@dlink.ru
Офисы
Украина,
04080 г. Киев , ул. Межигорская, 87-А, офис 18
Тел.: +38 (044) 545-64-40
E-mail: kiev@dlink.ru
Грузия
0162, г. Тбилиси,
проспект Чавчавадзе 74, 10 этаж
Тел./Факс: + 995 (32) 244-563
Беларусь
220114, г. Минск, проспект Независимости,
169 , БЦ "XXI Век"
Тел.: +375(17) 218-13-65
E-mail: minsk@dlink.ru
Lietuva
09120, Vilnius, Žirmūnų 139-303
Tel./faks. +370 (5) 236-3629
E-mail: info@dlink.lt
Казахстан,
050008, г. Алматы, ул. Курмангазы, дом 143
(уг. Муканова)
Тел./факс: +7 727 378-55-90
E-mail: almaty@dlink.ru
Узбекистан
100015, г.Ташкент, ул. Нукусская, 89
Тел./Факс: +998 (71) 120-3770, 150-2646
E-mail: tashkent@dlink.ru
Армения
0038, г. Ереван, ул. Абеляна, 6/1, 4 этаж
Тел./Факс: + 374 (10) 398-667
E-mail: erevan@dlink.ru
Eesti
Peterburi tee 46-205
11415, Tallinn, Eesti , Susi Bürookeskus
tel +372 613 9771
e-mail: info@dlink.ee
Latvija
Mazā nometņu 45/53 (ieeja no Nāras ielas)
LV-1002, Rīga
tel.: +371 6 7618703 +371 6 7618703
e-pasts: info@dlink.lv
SOPORTE TÉCNICO
Usted puede encontrar actualizaciones de softwares o firmwares y
documentación para usuarios a través de nuestro sitio www.dlinkla.com
SOPORTE TÉCNICO PARA USUARIOS EN LATINO AMERICA
Soporte técnico a través de los siguientes teléfonos de D-Link
PAIS
NUMERO
Argentina
0800 - 12235465
Chile
800 - 835465 ó (02) 5941520
Colombia
01800 - 9525465
Costa Rica
0800 - 0521478
Ecuador
1800 - 035465
El Salvador
800 - 6335
Guatemala
1800 - 8350255
México
01800 - 1233201
Panamá
011 008000525465
Perú
0800 - 00968
Venezuela
0800 - 1005767
Soporte Técnico de D-Link a través de Internet
Horario de atención Soporte Técnico en www.dlinkla.com
e-mail: soporte@dlinkla.com & consultas@dlinkla.com
Suporte Técnico
Caso tenha dúvidas na instalação do produto, entre em
contato com o Suporte Técnico D-Link por:
Chat Online
www.dlink.com.br/suporte
E-mail
suporte@dlink.com.br
Back Office
backoffice@dlink.com.br *
*Acionar Garantia para 4 ou mais equipamentos
Telefones
São Paulo: (11) 2755-6950
*GO: 4052-1850 (Ligação local)
*Nordeste: 0800-7024104
*Demais Estados: 4062-1850 (Ligação local)
*Apenas Modems ADSL
Garantia diferenciada vendida pela internet. Agilidade e
tranquilidade para suas atividades!
Conheça: http://garantiapremium.dlink.com.br
Atendimento disponível das 9h as 21h de segunda a sexta
feira e aos sábados das 9h as 15h
D-Link 友訊科技 台灣分公司
技術支援資訊
如果您還有任何本使用手冊無法協助您解決的產品相關問題,台灣
地區用戶可以透過我們的網站、電子郵件或電話等方式與D-Link台灣
地區技術支援工程師聯絡。
D-Link 免付費技術諮詢專線
0800-002-615
服務時間:週一至週五,早上9:00到晚上9:00
(不含周六、日及國定假日)
網
站:http://www.dlink.com.tw
電子郵件:dssqa_service@dlink.com.tw
如果您是台灣地區以外的用戶,請參考D-Link網站全球各地
分公司的聯絡資訊以取得相關支援服務。
產品保固期限、台灣區維修據點查詢,請參考以下網頁說明:
http://www.dlink.com.tw
產品維修:
使用者可直接送至全省聯強直營維修站或請洽您的原購買經銷商。
Dukungan Teknis
Update perangkat lunak dan dokumentasi pengguna
dapat diperoleh pada situs web D-Link.
Dukungan Teknis untuk pelanggan:
Dukungan Teknis D-Link melalui telepon:
Tel: +62-21-5731610
Dukungan Teknis D-Link melalui Internet:
Email : support@dlink.co.id
Website : http://support.dlink.co.id
Technical Support
この度は弊社製品をお買い上げいただき、誠にありがとうご
ざいます。
下記弊社 Web サイトからユーザ登録及び新製品登録を
行っていただき、ダウンロードサービスにて
サポート情報、ファームウェア、ユーザマニュアルを
ダウンロードすることができます。
ディーリンクジャパン Web サイト
URL:http://www.dlink-jp.com
技术支持
办公地址:北京市东城区北三环东路 36 号 环球贸易中心 B 座
26F 02-05 室 邮编: 100013
技术支持中心电话:8008296688/ (028)66052968
技术支持中心传真:(028)85176948
各地维修中心地址请登陆官方网站查询
网址:http://www.dlink.com.cn
办公时间:周一到周五,早09:00到晚18:00
Registration Card
All Countries and Regions Excluding USA
Print, type or use block letters.
Your name: Mr./Ms_____________________________________________________________________________
Organization: ________________________________________________ Dept. ____________________________
Your title at organization: ________________________________________________________________________
Telephone: _______________________________________ Fax:________________________________________
Organization's full address: ______________________________________________________________________
____________________________________________________________________________________________
Country: _____________________________________________________________________________________
Date of purchase (Month/Day/Year): _______________________________________________________________
Product Model
Product Serial No.
* Product installed in type of
computer
* Product installed in
computer serial No.
(* Applies to adapters only)
Product was purchased from:
Reseller's name: ______________________________________________________________________________
Telephone: _______________________________________
Answers to the following questions help us to support your product:
1. Where and how will the product primarily be used?
Home Office Travel Company Business Home Business Personal Use
2. How many employees work at installation site?
1 employee 2-9 10-49 50-99 100-499 500-999 1000 or more
3. What network protocol(s) does your organization use ?
XNS/IPX TCP/IP DECnet Others_____________________________
4. What network operating system(s) does your organization use ?
D-Link LANsmart Novell NetWare NetWare Lite SCO Unix/Xenix PC NFS 3Com 3+Open Cisco Network
Banyan Vines DECnet Pathwork Windows NT Windows 98 Windows 2000/ME Windows XP
Others__________________________________________
5. What network management program does your organization use ?
D-View HP OpenView/Windows HP OpenView/Unix SunNet Manager Novell NMS
NetView 6000 Others________________________________________
6. What network medium/media does your organization use ?
Fiber-optics Thick coax Ethernet Thin coax Ethernet 10BASE-T UTP/STP
100BASE-TX 1000BASE-T Wireless 802.11b and 802.11g wireless 802.11a Others_________________
7. What applications are used on your network?
Desktop publishing Spreadsheet Word processing CAD/CAM
Database management Accounting Others_____________________
8. What category best describes your company?
Aerospace Engineering Education Finance Hospital Legal Insurance/Real Estate Manufacturing
Retail/Chain store/Wholesale Government Transportation/Utilities/Communication VAR
System house/company Other________________________________
9. Would you recommend your D-Link product to a friend?
Yes No Don't know yet
10.Your comments on this product?
__________________________________________________________________________________________
__________________________________________________________________________________________